Powered by Deep Web Technologies
Note: This page contains sample records for the topic "alcohol msds section" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


1

Material Safety Data Sheet MSDS ID NO.: 0137SPE012  

Alternative Fuels and Advanced Vehicles Data Center (EERE)

Material Safety Data Sheet Material Safety Data Sheet MSDS ID NO.: 0137SPE012 Revision date: 05/25/2011 1. CHEMICAL PRODUCT AND COMPANY INFORMATION Product name: Speedway E85 Synonym: Speedway ED75/ED85; E-75; E75; E-85; E85; Ethanol/Gasoline Fuel Blend; Fuel Ethanol ED75/ED85 Chemical Family: Gasoline/Ethanol Formula: Mixture Manufacturer: Speedway LLC P.O. Box 1500 Enon, OH 45501 Other information: 419-421-3070 Emergency telephone number: 877-627-5463 2. COMPOSITION/INFORMATION ON INGREDIENTS E85 is a mixture of ethyl alcohol and gasoline that is approved for use in an automobile spark ignition engine. Can contain small amounts of dye and other additives (>0.02%) which are not considered hazardous at the concentrations used. Product information: Name CAS Number

2

NITROGEN -N2 MSDS (Document # 001040) PAGE 1 OF 10 MATERIAL SAFETY DATA SHEET  

E-Print Network (OSTI)

in an emergency? 1. PRODUCT IDENTIFICATION CHEMICAL NAME; CLASS: NITROGEN - N2 LIQUEFIED NITROGEN N2, (CryogenicNITROGEN - N2 MSDS (Document # 001040) PAGE 1 OF 10 MATERIAL SAFETY DATA SHEET Prepared to U ppm ppm ppm Nitrogen 7727-37-9 >99 % There are no specific exposure limits for Nitrogen. Nitrogen

Choi, Kyu Yong

3

State of California BOARD OF EQUALIZATION ALCOHOLIC BEVERAGE TAX REGULATIONS  

E-Print Network (OSTI)

section 23007, is presumed to contain 0.5 percent or more alcohol by volume derived from flavors or other ingredients containing alcohol obtained from the distillation of fermented agricultural products, unless this

unknown authors

2008-01-01T23:59:59.000Z

4

Alcohol fired alcohol fuel still  

Science Conference Proceedings (OSTI)

The best method for using alcohol as the base for alcohol fuel distillation would be in the conservation of the initial heat input. In other words, the 20 gallon system would, at the end of a load, in effect waste a full gallon of alcohol fuel with each batch. Therefore either a continual feed system needs to be developed which would serve the 20 gallon heater or heat exchangers of some type should be designed to salvage a great portion of the heat. If, on the other hand, large amounts of fuel are not required, a large single batch still fired by alcohol would not be too wasteful. It would be adviseable that some form of alcohol fuel research both small and large scale be continued. While not necessarily an important part of the energy picture now, it may well be in the future. It could also open up overseas markets where fuels in liquid form are scarce, yet raw materials are not. Lastly, this project, while accomplishing muon, needs further study to make the system more efficient in fuel economy.

Johnson, F.

1982-01-01T23:59:59.000Z

5

Alcohol fuels program technical review  

DOE Green Energy (OSTI)

The last issue of the Alcohol Fuels Process R/D Newsletter contained a work breakdown structure (WBS) of the SERI Alcohol Fuels Program that stressed the subcontracted portion of the program and discussed the SERI biotechnology in-house program. This issue shows the WBS for the in-house programs and contains highlights for the remaining in-house tasks, that is, methanol production research, alcohol utilization research, and membrane research. The methanol production research activity consists of two elements: development of a pressurized oxygen gasifier and synthesis of catalytic materials to more efficiently convert synthesis gas to methanol and higher alcohols. A report is included (Finegold et al. 1981) that details the experimental apparatus and recent results obtained from the gasifier. The catalysis research is principally directed toward producing novel organometallic compounds for use as a homogeneous catalyst. The utilization research is directed toward the development of novel engine systems that use pure alcohol for fuel. Reforming methanol and ethanol catalytically to produce H/sub 2/ and CO gas for use as a fuel offers performance and efficiency advantages over burning alcohol directly as fuel in an engine. An application of this approach is also detailed at the end of this section. Another area of utilization is the use of fuel cells in transportation. In-house researchers investigating alternate electrolyte systems are exploring the direct and indirect use of alcohols in fuel cells. A workshop is being organized to explore potential applications of fuel cells in the transportation sector. The membrane research group is equipping to evaluate alcohol/water separation membranes and is also establishing cost estimation and energy utilization figures for use in alcohol plant design.

Not Available

6

European Section  

Science Conference Proceedings (OSTI)

European geographical region. European Section Sections achievement application award awards canadian distinguished division fats member membership memorial network nomination oils poster program recognizing research section service European Secti

7

Australasian Section  

Science Conference Proceedings (OSTI)

The Australasian Section brings together professionals in the Australia and Pacific Rim geographical regions. Australasian Section Sections achievement application award awards canadian distinguished division fats member membership memorial networ

8

Asian Section  

Science Conference Proceedings (OSTI)

Taiwan, Japan, and Korea geographical regions. Asian Section Sections achievement application award awards canadian distinguished division fats member membership memorial network nomination oils poster program recognizing research section service

9

Canadian Section  

Science Conference Proceedings (OSTI)

Bringing together professionals from Canadian geographical regions. Canadian Section Sections achievement application award awards canadian distinguished division fats member membership memorial network nomination oils poster program recognizing r

10

USA Section  

Science Conference Proceedings (OSTI)

Section is made up of professionals in the USA. USA Section Membership Information achievement application award Awards distinguished division Divisions fats job Join lipid lipids Member member get a member Membership memorial nomination oils post

11

Indian Section  

Science Conference Proceedings (OSTI)

Bringing together professionals in the geographic area of India. Indian Section Sections achievement application award awards canadian distinguished division fats member membership memorial network nomination oils poster program recognizing resear

12

Furfuryl alcohol cellular product  

DOE Patents (OSTI)

Self-extinguishing rigid foam products are formed by polymerization of furfuryl alcohol in the presence of a lightweight, particulate, filler, zinc chloride and selected catalysts.

Sugama, T.; Kukacka, L.E.

1982-05-26T23:59:59.000Z

13

Extracting alcohols from aqueous solutions  

DOE Patents (OSTI)

Hydrocarbon and surfactants are contacted with a solution of alcohol and water to extract the alcohol into the hydrocarbon-surfactant mixture.

Compere, Alicia L. (Knoxville, TN); Googin, John M. (Oak Ridge, TN); Griffith, William L. (Oak Ridge, TN)

1984-01-01T23:59:59.000Z

14

Alcohol fuel conversion apparatus  

Science Conference Proceedings (OSTI)

This patent describes an alcohol fuel conversion apparatus for internal combustion engines comprising: fuel storage means for containing an alcohol fuel; primary heat exchange means in fluid communication with the fuel storage means for transferring heat to pressurized alcohol contained within the heat exchange means; a heat source for heating the primary heat exchange means; pressure relief valve means in closed fluid communication with the primary heat exchange means for releasing heated pressurized alcohol into an expansion chamber; converter means including the expansion chamber in fluid communication with the pressure relief valve means for receiving the heated pressurized alcohol and for the vaporization of the alcohol; fuel injection means in fluid communication with the converter means for injecting vaporized alcohol into the cylinders of an internal combustion engine for mixing with air within the cylinders for proper combustion; and pump means for pressurized pumping of alcohol from the 23 fuel storage means to the primary heat exchanger means, converter means, fuel injector means, and to the engine.

Carroll, B.I.

1987-12-08T23:59:59.000Z

15

Alcohol | OpenEI  

Open Energy Info (EERE)

Alcohol Alcohol Dataset Summary Description The Energy Statistics Database contains comprehensive energy statistics on the production, trade, conversion and final consumption of primary and secondary; conventional and non-conventional; and new and renewable sources of energy. The Energy Statistics dataset, covering the period from 1990 on, is available at UNdata. This dataset relates to the consumption of alcohol by the transportation industry. Source United Nations (UN) Date Released December 09th, 2009 (5 years ago) Date Updated Unknown Keywords Agriculture Alcohol consumption transportation industry UN Data application/xml icon UN Data: consumption by transportation industry XML (xml, 95 KiB) text/csv icon UN Data: consumption by transportation industry XLS (csv, 21.6 KiB)

16

Section J  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

M-1 Section J Appendix M Key Design, Licensing and Site Management M&O Milestone Chart Activity Planned Date Develop and Submit CD-2 (25%-30%) 082009 Submission of Construction...

17

SECTION M  

NLE Websites -- All DOE Office Websites (Extended Search)

using the policies and procedures in FAR Part 15 and DEAR Part 915. A Source Evaluation Board (SEB) will evaluate proposals using the criteria in this Section M. The Source...

18

Section J  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

L-1 L-1 Section J Appendix L MEMORANDUM FROM DAVID R. HILL, GENERAL COUNSEL, DATED NOVEMBER 30, 2006, SUBJECT: ONGOING LICENSING SUPPORT NETWORK ("LSN") OBLIGATIONS Contract No.: DE-RW0000005 QA:QA J-L-2 Contract No.: DE-RW0000005 QA:QA J-L-3 Contract No.: DE-RW0000005

19

Production of hydrogen from alcohols  

DOE Patents (OSTI)

A process for producing hydrogen from ethanol or other alcohols. The alcohol, optionally in combination with water, is contacted with a catalyst comprising rhodium. The overall process is preferably carried out under autothermal conditions.

Deluga, Gregg A. (St. Paul, MN); Schmidt, Lanny D. (Minneapolis, MN)

2007-08-14T23:59:59.000Z

20

Fermentative alcohol production  

DOE Patents (OSTI)

An improved fermentation process for producing alcohol which includes the combination of vacuum fermentation and vacuum distillation. Preferably, the vacuum distillation is carried out in two phases, one a fermentor proper operated at atmospheric pressure and a flash phase operated at reduced pressure with recycle of fermentation brew having a reduced alcohol content to the fermentor, using vapor recompression heating of the flash-pot recycle stream to heat the flash-pot or the distillation step, and using "water load balancing" (i.e., the molar ratio of water in the fermentor feed is the same as the molar ratio of water in the distillation overhead).

Wilke, Charles R. (El Cerrito, CA); Maiorella, Brian L. (Berkeley, CA); Blanch, Harvey W. (Berkeley, CA); Cysewski, Gerald R. (Kennewick, WA)

1982-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "alcohol msds section" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


21

Section 66  

NLE Websites -- All DOE Office Websites (Extended Search)

CFCl CFCl 3 ) (CF 2 Cl 2 ) (CHFCl 2 ) CF 4 CCl 4 (CFCl 3 ) (CF 2 Cl 2 ) (CHFCl 2 ) SF 6 CF 4 CCl 4 Session Papers 277 Figure 1. Spectral absorption cross-sections of CF 4 between 1281 and 1284 cm . The experimental -1 conditions correspond to the surface, 5-km, and 19-km levels of the U.S. Standard Atmosphere. Figure 2. Spectral absorption cross-sections of CCl 4 between 755 and 810 cm . The experimental conditions -1 correspond to the surface, 5-km, and 19-km levels of the U.S. Standard Atmosphere. Laboratory Spectroscopy in Support of the Atmospheric Radiation Measurement Program P. Varanasi Institute for Terrestrial and Planetary Atmospheres The University at Stony Brook Stony Brook, New York There is considerable world-wide interest in the remote sensing of chlorofluorocarbons (CFCs), especially CFC-11

22

SECTION J  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

J-F-1 SECTION J APPENDIX F CRITICAL STAFF Subject Matter Expert Subject Matter Canister Transfer Machine Engineering Waste Package Transfer Trolley Engineering Transport and Emplacement Vehicle Engineering Cask Transfer Trolley Engineering Criticality and Nuclear Engineering Subsurface Thermal Management Engineering Pre-closure Safety Analysis Specialist Waste Package and Drip Shields Engineering Waste Package Closure System Engineering NOG-1 Cranes Engineering Subsurface Design Engineering Structural Seismic Design Engineering Transport, Aging, and Disposal (TAD) interface with repository systems Note: The Contractor shall identify names of at least one individual which shall function in each of the subject matter areas identified above. Qualification requirements for these individuals are

23

SECTION J  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

D-1 D-1 SECTION J APPENDIX D KEY PERSONNEL Name Position Doug Cooper General Manager John Donnell Repository Licensing Lead Al Ebner, PE, PhD Repository Design Lead Steve Piccolo Deputy General Manager Steve White Quality & Performance Assurance Lead George Clare Project Management & Integration Lead Mike Hitchler Preclosure Safety Analysis Lead Contract No.: DE-RW0000005 QA:QA J-D-2 POSITION DESCRIPTIONS OCRWM SPECIFIED KEY PERSONNEL 1. General Manager: Requires 10 years experience as a Senior Manager, responsible for the licensing and/or design and/or operation of a large complex nuclear facility. Must have experience as a

24

State of California BOARD OF EQUALIZATION ALCOHOLIC BEVERAGE TAX REGULATIONS  

E-Print Network (OSTI)

Effective October 1, 2008, for purposes of tax reporting, a taxpayer will be deemed to have correctly classified an alcoholic beverage as not being a distilled spirit, as defined by Business and Professions Code section 23005, if at the time taxes are imposed, as set forth in the Revenue and Taxation Code, division 2, part 14, chapters 4, 5, and

unknown authors

2008-01-01T23:59:59.000Z

25

SECTION J  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

H-1 H-1 SECTION J APPENDIX H CONTRACT GUIDANCE FOR PREPARATION OF DIVERSITY PLAN This Guidance is to assist the Contractor in understanding the information being sought by the Department for each of the Diversity elements and where these issues may already be addressed in the contract. To the extent these issues are already addressed in the contract, the Contractor need only cross reference the location. Contractor's Workforce The Department's contracts contain clauses on Equal Employment Opportunity (EEO) and Affirmative Action (AA). The Plan may discuss how the contractor has or plans to establish and maintain result-oriented EEO and AA programs in accordance with the requirements of these clauses, and how the contractor's organization includes

26

Section J  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

M-1 M-1 Section J Appendix M Key Design, Licensing and Site Management M&O Milestone Chart Activity Planned Date Develop and Submit CD-2 (25%-30%) 08/2009 Submission of Construction Performance Specifications - Balance of Plant Support Facilities (OCRWM Start of Construction 3/2012) TBD Submission of Construction Performance Specifications - Initial Handling Facility (IHF) (OCRWM Start of Construction for IHF: 9/2013) TBD Submission of Construction Performance Specifications - Wet Handling Facility (WHF) (OCRWM Start of Construction for WHF: 12/2012) TBD Submission of Construction Performance Specifications - Canister Receipt and Closure Facility (CRCF) (OCRWM Start of Construction for CRCF-1: 10/2011) TBD Submission of Construction Performance Specifications - Panel 1

27

Section 19  

NLE Websites -- All DOE Office Websites (Extended Search)

Observations and Applications of Data Taken with the Observations and Applications of Data Taken with the Cloud Profiling Radar System J. M. Firda, S. M. Sekelsky, S. P. Lohmeier, R. E. McIntosh Microwave Remote Sensing Laboratory, University of Massachusetts Amherst, Massachusetts Introduction During the past year, the University of Massachusetts' Cloud Profiling Radar System (CPRS) team has been active in collecting and processing data. Participation in several field campaigns has produced new and interesting data sets. A classification software was also developed using rule-based techniques and neural networks to identify cloud particles. This paper describes the activities of CPRS from March of 1995 to March of 1996. In the first section, involvement in field experiments is briefly described. This is followed by a

28

Section Number:  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

QA:QA J-E-1 SECTION J APPENDIX E LIST OF APPLICABLE DIRECTIVES Pursuant to the contract clause entitled, "Laws, Regulations, and DOE Directives," the following list of directives is applicable to this contract. List A Pursuant to the contract clause entitled, "Laws, Regulations, and DOE Directives," the Contractor shall comply with the requirements of applicable Federal, State, and local laws and regulations, unless relief has been granted in writing by the appropriate regulatory agency. Omission of any applicable law or regulation from this list does not affect the obligation of the contractor to comply with such law or regulation. Laws & Regulations Title 10 CFR Part 2 Rules of Practice for Domestic Licensing Proceedings and Issuance of Orders

29

Generation of electricity with fuel cell using alcohol fuel  

Science Conference Proceedings (OSTI)

This patent describes a method for generating electricity in a fuel cell, the fuel cell comprising a cathode, an electrolyte, an anode comprising a first, fluid-permeable face and a second face in contact with the electrolyte, and an external circuit connecting the cathode and the anode. It comprises bringing a lower primary alcohol into contact with the first fluid-permeable face of the anode, thereby permitting the lower primary alcohol to penetrate into the cross-section of the anode toward the second face; oxidizing the lower primary alcohol essentially to carbon dioxide and water at the second face of the anode, reducing a reducible gas at the cathode, and obtaining electricity from the fuel cell.

Reddy, N.R.K.V.; Taylor, E.J.

1992-07-21T23:59:59.000Z

30

Alcoholes Biocarburantes de Extremadura Albiex | Open Energy...  

Open Energy Info (EERE)

Name Alcoholes Biocarburantes de Extremadura (Albiex) Place Spain Product Spanish bioethanol producer building a plant in Extremadura. References Alcoholes Biocarburantes de...

31

Gene therapy in alcoholic rats  

NLE Websites -- All DOE Office Websites (Extended Search)

70 70 Sept. 9, 2001 Gene Therapy Reduces Drinking in "Alcoholic" Rats UPTON, NY - Scientists at the U.S. Department of Energy's Brookhaven National Laboratory have shown that increasing the level of a brain protein important for transmitting pleasure signals can turn rats that prefer alcohol into light drinkers, and those with no preference into near teetotalers. The findings, published in the first September 2001 issue of the Journal of Neurochemistry (Vol. 78, No. 5), may have implications for the prevention and treatment of alcoholism in humans. "This is a preliminary study, but when you see a rat that chooses to drink 80 to 90 percent of its daily fluid as alcohol, and then three days later it's down to 20 percent, that's a dramatic drop in alcohol intake - a very clear change in behavior," said Panayotis Thanos, the lead researcher. "This gives us great hope that we can refine this treatment for future clinical use."

32

Australasian Section Newsletter  

Science Conference Proceedings (OSTI)

Read the Australasian Section Newsletter. Australasian Section Newsletter Australasian Section aaocs aocs australasian Australasian Sections Australia award awards excellence fats global inform job listings member membership network oils Pacific Rim Prof

33

Small-scale alcohol fuel plant. Final report  

DOE Green Energy (OSTI)

The objective to decrease the cost of distillation by the use of solar heat and a vacuum system combined was achieved. My original design of a single pot type still was altered during construction by dividing the distillation tank into three sections with a condenser coil after each section so that 160+ proof alcohol can be acquired without extensive reflux. However, some reflux will still be necessary to extract the most alcohol possible from the mash. This proto-type still could be reproduced for use as an On the Farm Plant if the components are size matched and the modifications are incorporated as I have outlined in Conclusions and Recommendations on page No. 4 of this report.

Fitzcharles, H.M. III

34

State of California BOARD OF EQUALIZATION ALCOHOLIC BEVERAGE TAX REGULATIONS  

E-Print Network (OSTI)

A person may be relieved from the liability for the payment of alcoholic beverage taxes, including any penalties and interest added to those taxes, when that liability resulted from the failure to make a timely return or a payment and such failure was found by the board to be due to reasonable reliance on written advice given by the board as described in California Code of Regulations, Title 18, Section 4902.

unknown authors

2002-01-01T23:59:59.000Z

35

Alcohol fuel from Ohio farms  

Science Conference Proceedings (OSTI)

This booklet provides an introduction to technical, marketing, and regulatory issues involved in on-farm alcohol fuel production. Discussed are ethanol production provcesses, investment, potential returns, regulations and permits, and sources of financial and technical assistance. 2 figures. (DMC)

Jones, J.D.

1984-01-01T23:59:59.000Z

36

Mixed Alcohol Synthesis Catalyst Screening  

DOE Green Energy (OSTI)

National Renewable Energy Laboratory (NREL) and Pacific Northwest National Laboratory (PNNL) are conducting research to investigate the feasibility of producing mixed alcohols from biomass-derived synthesis gas (syngas). PNNL is tasked with obtaining commercially available or preparing promising mixed-alcohol catalysts and screening them in a laboratory-scale reactor system. Commercially available catalysts and the most promising experimental catalysts are provided to NREL for testing using a slipstream from a pilot-scale biomass gasifier. From the standpoint of producing C2+ alcohols as the major product, it appears that the rhodium catalyst is the best choice in terms of both selectivity and space-time yield (STY). However, unless the rhodium catalyst can be improved to provide minimally acceptable STYs for commercial operation, mixed alcohol synthesis will involve significant production of other liquid coproducts. The modified Fischer-Tropsch catalyst shows the most promise for providing both an acceptable selectivity to C2+ alcohols and total liquid STY. However, further optimization of the Fischer-Tropsch catalysts to improve selectivity to higher alcohols is highly desired. Selection of a preferred catalyst will likely entail a decision on the preferred coproduct slate. No other catalysts tested appear amenable to the significant improvements needed for acceptable STYs.

Gerber, Mark A.; White, James F.; Stevens, Don J.

2007-09-03T23:59:59.000Z

37

Alcohol consumption, medical conditions and health behavior in older adults  

E-Print Network (OSTI)

Alcohol consumption In press, American JournalHealth Behavior Alcohol Consumption, Medical Conditions andin the association of alcohol consumption with health and

Satre, Derek; Gordon, Nancy P.; Weisner, Constance

2007-01-01T23:59:59.000Z

38

Section Administration and Resources  

Science Conference Proceedings (OSTI)

Section Information, Membership, Newsletters and Awards Section Administration and Resources Awards Program aocs award Awards baldwin fats global inform job listings member membership network oils ...

39

Autothermal Partial Oxidation of Ethanol and Alcohols  

Autothermal Reforming of Ethanol and Alcohols into Syngas Ethanol and alcohols can be converted into syngas using a robust autothermal reforming process. Syngas is a mixture of carbon monoxide and hydrogen that can be used to synthesize other ...

40

European Section Articles of interest.  

Science Conference Proceedings (OSTI)

European geographical region. European Section Articles of interest. Sections award awards canadian division fats member membership network oils section European Section aocs awards European Section European Section Awards for Young Lipid Scienti

Note: This page contains sample records for the topic "alcohol msds section" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


41

Alcohol Fuels Program. Final technical report  

DOE Green Energy (OSTI)

The activities and accomplishments of the alcohol fuels program are reviewed briefly. Educational and promotional activities are described. (MHR)

Weiss, G.M.

1982-01-01T23:59:59.000Z

42

Division and Section Awards  

Science Conference Proceedings (OSTI)

Division and Section Awards Division and Section Awards Divisions achievement agricultural analytical application award awards biotechnology detergents distinguished division Divisions edible fats food Interest Area lipid lipids member membership

43

Sections / Geographical Regions Information  

Science Conference Proceedings (OSTI)

AOCS Sections provide a local forum for fats and oils professionals. Building a Stronger Global Association Sections / Geographical Regions Information Divisions achievement agricultural analytical application award awards biotechnology detergents

44

Hydride transfer made easy in the oxidation of alcohols catalyzed by choline oxidase  

Science Conference Proceedings (OSTI)

Choline oxidase (E.C. 1.1.3.17) catalyzes the two-step, four-electron oxidation of choline to glycine betaine with betaine aldehyde as enzyme-associated intermediate and molecular oxygen as final electron acceptor (Scheme 1). The gem-diol, hydrated species of the aldehyde intermediate of the reaction acts as substrate for aldehyde oxidation, suggesting that the enzyme may use similar strategies for the oxidation of the alcohol substrate and aldehyde intermediate. The determination of the chemical mechanism for alcohol oxidation has emerged from biochemical, mechanistic, mutagenetic, and structural studies. As illustrated in the mechanism of Scheme 2, the alcohol substrate is initially activated in the active site of the enzyme by removal of the hydroxyl proton. The resulting alkoxide intermediate is then stabilized in the enzyme-substrate complex via electrostatic interactions with active site amino acid residues. Alcohol oxidation then occurs quantum mechanically via the transfer of the hydride ion from the activated substrate to the N(5) flavin locus. An essential requisite for this mechanism of alcohol oxidation is the high degree of preorganization of the activated enzyme-substrate complex, which is achieved through an internal equilibrium of the Michaelis complex occurring prior to, and independently from, the subsequent hydride transfer reaction. The experimental evidence that support the mechanism for alcohol oxidation shown in Scheme 2 is briefly summarized in the Results and Discussion section.

Gadda, G.; Orville, A.; Pennati, A.; Francis, K.; Quaye, O.; Yuan, H.; Rungsrisuriyachai, K.; Finnegan, S.; Mijatovic, S.; Nguyen, T.

2008-06-08T23:59:59.000Z

45

Section J: HOUSEHOLD CHARACTERISTICS  

U.S. Energy Information Administration (EIA)

2001 Residential Energy Consumption Survey Form EIA-457A (2001)--Household Questionnaire OMB No.: 1905-0092, Expiring February 29, 2004 42 Section J: HOUSEHOLD ...

46

Section D: SPACE HEATING  

U.S. Energy Information Administration (EIA)

2005 Residential Energy Consumption Survey Form EIA-457A (2005)--Household Questionnaire OMB No.: 1905-0092, Expiring May 31, 2008 33 Section D: SPACE HEATING

47

Special Section on RFID  

E-Print Network (OSTI)

The eight articles in this special section describe state-of-the-art technologies and tools and one application of RFID.

Engels, Daniel W.

48

Material Safety Data Sheet Isopropyl  

NLE Websites -- All DOE Office Websites (Extended Search)

Safety Safety Data Sheet Isopropyl alcohol MSDS Section 1: Chemical Product and Company Identification Product Name: Isopropyl alcohol Catalog Codes: SLI1153, SLI1579, SLI1906, SLI1246, SLI1432 CAS#: 67-63-0 RTECS: NT8050000 TSCA: TSCA 8(b) inventory: Isopropyl alcohol CI#: Not available. Synonym: 2-Propanol Chemical Name: isopropanol Chemical Formula: C3-H8-O Contact Information: Sciencelab.com, Inc. 14025 Smith Rd. Houston, Texas 77396 US Sales: 1-800-901-7247 International Sales: 1-281-441-4400 Order Online: ScienceLab.com CHEMTREC (24HR Emergency Telephone), call: 1-800-424-9300 International CHEMTREC, call: 1-703-527-3887 For non-emergency assistance, call: 1-281-441-4400 Section 2: Composition and Information on Ingredients Composition: Name CAS # % by Weight Isopropyl alcohol 67-63-0 100 Toxicological Data on Ingredients: Isopropyl alcohol: ORAL

49

Sectional device handling tool  

DOE Patents (OSTI)

Apparatus for remotely handling a device in an irradiated underwater environment includes a plurality of tubular sections interconnected end-to-end to form a handling structure, the bottom section being adapted for connection to the device. A support section is connected to the top tubular section and is adapted to be suspended from an overhead crane. Each section is flanged at its opposite ends. Axially retractable bolts in each bottom flange are threadedly engageable with holes in the top flange of an adjacent section, each bolt being biased to its retracted position and retained in place on the bottom flange. Guide pins on each top flange cooperate with mating holes on adjacent bottom flanges to guide movement of the parts to the proper interconnection orientation. Each section carries two hydraulic line segments provided with quick-connect/disconnect fittings at their opposite ends for connection to the segments of adjacent tubular sections upon interconnection thereof to form control lines which are connectable to the device and to an associated control console.

Candee, Clark B. (Monroeville, PA)

1988-07-12T23:59:59.000Z

50

Section Building Training Manual  

E-Print Network (OSTI)

) to enter search criteria. 3. Enter the term you are searching in. 4. Enter section search criteria (subject Exit #12;6 Adding a Section of a Course 1. Access the Schedule Form (SSASECT). 2. Enter the term code. 14. Tab to the Part of Term field. Enter the Part of Term code (will be 1 for Fall, Spring and Summer

Kelly, Scott David

51

South Dakota alcohol fuel production handbook: permits, regulations, and assistance  

SciTech Connect

This handbook contains information on South Dakota alcohol legislation, and information on the various types of additional government program assistance available to the alcohol producer. It was prepared to assist potential alcohol producers with federal and state permit prerequisites. (DMC)

1980-01-01T23:59:59.000Z

52

Formation of alcohol conversion catalysts  

DOE Patents (OSTI)

The method of the present invention involves a composition containing an intimate mixture of (a) metal oxide support particles and (b) a catalytically active metal oxide from Groups VA, VIA, or VIIA, its method of manufacture, and its method of use for converting alcohols to aldehydes. During the conversion process, catalytically active metal oxide from the discrete catalytic metal oxide particles migrates to the oxide support particles and forms a monolayer of catalytically active metal oxide on the oxide support particle to form a catalyst composition having a higher specific activity than the admixed particle composition.

Wachs, Israel E. (Bridgewater, NJ); Cai, Yeping (Louisville, KY)

2001-01-01T23:59:59.000Z

53

Alcohol Outlets and Violent Crime in Washington D.C.  

E-Print Network (OSTI)

Alcohol Availability and Crime: Evidence From Census Tractand Ontkush, M. J. Violent Crime and Alcohol Availability:Neighborhoods and Urban Crimes. Social Forces. 1996;75:619-

Franklin, F. Abron; LaVeist, Thomas A.; Webster, Daniel W.; Pan, William K.

2010-01-01T23:59:59.000Z

54

Solid alcohol fuel with hydration inhibiting coating  

Science Conference Proceedings (OSTI)

This patent describes a process for preparing a solid alcohol fuel. It comprises: mixing an alcohol solution with a cellulose derivative having a hydration inhibiting coating thereby forming a slurry and then adding an effective amount sufficient to increase the pH level above 8, of a caustic material so as to effect hydration and solidification.

Gartner, S.

1990-11-20T23:59:59.000Z

55

Alcohol fuel research in Turkey  

Science Conference Proceedings (OSTI)

Turkey, like most of the developing countries of the world, has vast agricultural potential, yet the country is highly dependent on oil imports, which satisfy 90% of its crude oil demand. Since Turkey had an economy based on agriculture, the usage of national resources in the energy field is extremely important. In the first years of the Turkish Republic, in 1931, the usage of national resources as an alternative to conventional fuels became a subject of increasing interest. Since then a lot of research has been conducted, but only a limited amount of application has been realized. Alcohol has always occupied an important place among the alternative fuel studies. The subject has been the scope of some research institute projects and university and government development planning studies. In Turkey, one of the most important studies in this area has been undertaken by the authors` research group in their university. This study is a general review of alcohol usage as an alternative automotive fuel in Turkey. This review includes a short history of the subject, the approach of the government, the research results, possible developments on the subject in the near future, and finally, it concludes with proposals.

Karaosmanoglu, F.; Isigiguer-Erguedenler, A.; Aksoy, H.A. [Istanbul Technical Univ. (Turkey). Dept. of Chemical Engineering

1998-12-01T23:59:59.000Z

56

Alcohol Transportation Fuels Demonstration Program  

DOE Green Energy (OSTI)

Hawaii has abundant natural energy resources, especially biomass, that could be used to produce alternative fuels for ground transportation and electricity. This report summarizes activities performed during 1988 to June 1991 in the first phase of the Alcohol Transportation Fuels Demonstration Program. The Alcohol Transportation Fuels Demonstration Program was funded initially by the Energy Division of the State of Hawaii's Department of Business, Economic Development and Tourism, and then by the US Department of Energy. This program was intended to support the transition to an altemative transportation fuel, methanol, by demonstrating the use of methanol fuel and methanol-fueled vehicles, and solving the problems associated with that fuel. Specific objectives include surveying renewable energy resources and ground transportation in Hawaii; installing a model methanol fueling station; demonstrating a methanol-fueled fleet of (spark-ignition engine) vehicles; evaluating modification strategies for methanol-fueled diesel engines and fuel additives; and investigating the transition to methanol fueling. All major objectives of Phase I were met (survey of local renewable resources and ground transportation, installation of methanol refueling station, fleet demonstration, diesel engine modification and additive evaluation, and dissemination of information on alternative fueling), and some specific problems (e.g., relating to methanol fuel contamination during handling and refueling) were identified and solved. Several key issues emerging from Phase I (e.g., methanol corrosion, flame luminosity, and methanol-transition technoeconomics) were recommended as topics for follow-on research in subsequent phases of this program.

Kinoshita, C.M. (ed.)

1990-01-01T23:59:59.000Z

57

Building, landscape and section  

E-Print Network (OSTI)

All buildings have in their section a relationship to the landscape on which they are sited. Therefore we as inhabitants of these buildings may or may not have a relationship with the landscape. It is the supposition of ...

Johnson, Daniel B. (Daniel Bryant)

1992-01-01T23:59:59.000Z

58

Cross-section  

NLE Websites -- All DOE Office Websites (Extended Search)

Cross-section Cross-section formulae for specific processes 1 39. CROSS-SECTION FORMULAE FOR SPECIFIC PROCESSES Revised September 2005 by R.N. Cahn (LBNL). Setting aside leptoproduction (for which, see Sec. 16), the cross sections of primary interest are those with light incident particles, e + e - , γγ, qq, gq , gg, etc., where g and q represent gluons and light quarks. The produced particles include both light particles and heavy ones - t, W , Z, and the Higgs boson H. We provide the production cross sections calculated within the Standard Model for several such processes. 39.1. Resonance Formation Resonant cross sections are generally described by the Breit-Wigner formula (Sec. 16 of this Review). σ(E) = 2J + 1 (2S 1 + 1)(2S 2 + 1) 4π k 2 Γ 2 /4 (E - E 0 ) 2 + Γ 2 /4 B in B out , (39.1) where E is the c.m. energy, J is the spin of the resonance, and the number of polarization states of the two incident particles

59

TABLE OF CONTENTS SECTION A: PREINTERVIEW OBSERVATION  

Gasoline and Diesel Fuel Update (EIA)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 SECTION E: WATER HEATING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....

60

Alcoholic fermentation of sorghum without cooking  

Science Conference Proceedings (OSTI)

Sorgum was used as raw material for alcoholic fermentation without cooking. Two varieties of sorghum grown in Thailand, KU 439 and KU 257, contained 80.0 and 75.8% of total sugar. Optimum amount of sorghum for alcoholic fermentation should be between 30 and 35% (w/v) in the fermentation broth. In these conditions 13.0 and 12.6% (v/v) of alcohol could be obtained in 84 and 91.9% yield based on the theoretical value of the starch content from KU 439 and KU 257, respectively.

Thammarutwasik, P.; Koba, Y.; Ueda, S.

1986-07-01T23:59:59.000Z

Note: This page contains sample records for the topic "alcohol msds section" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


61

European Section List  

Science Conference Proceedings (OSTI)

Name AffiliationCity, State, CountryEuropean Section2013 Members171 Members as of July 1, 2013Abend, SvenKolb Distribution LtdHedingen, SwitzerlandAlekperov, DzhamilAzersun HoldingBaku, AzerbaijanAnderberg, CathrineNovozymes ASBagsvaerd, DenmarkAracil, Jos

62

India Section List  

Science Conference Proceedings (OSTI)

Name AffiliationCity, State, CountryIndia Section2013 Members63 Members as of October 1, 2013Agarwal, RavindraPondicherry UniversityPondicherry, TN, IndiaAggarwal, Ram SarupBunge India Pvt LtdRajpura, PB, IndiaAgrawal, MiteshNICMARKhandwa, MP, IndiaAhuja,

63

Canadian Section List  

Science Conference Proceedings (OSTI)

Name AffiliationCity, State, CountryCanadian Section2013 Members243 Members as of October 1, 2013Abuzaytoun, ReemDalhousie UniversityHalifax, NS, CanadaAcosta, EdgarUniversity of TorontoToronto, ON, CanadaAlfieri, JocelynSilliker Canada CoMarkham, ON, Cana

64

Australasian Section List  

Science Conference Proceedings (OSTI)

Name AffiliationCity, State, CountryAustralasian Section2013 Members76 Members as of October 1, 2013Abeywardena, MahindaCSIRO Health NutritionAdelaide, SA, AustraliaAdcock, JacquiDeakin UniversityWaurn Ponds, VIC, Ariyapperuma, YasindaMSM MillingManildra,

65

Latin American Section List  

Science Conference Proceedings (OSTI)

Name AffiliationCity, State, CountryLatin American Section2013 Members208 Members as of October 1, 2013Abril, RubenDSM Nutritional ProductsBoulder, CO, USAAcevedo, NuriaUniversity of GuelphAmes, IA, USAAcosta, EdgarUniversity of TorontoToronto, ON, CanadaA

66

USA Section List  

Science Conference Proceedings (OSTI)

Name AffiliationCity, State, CountryUSA Section2013 Members919 Members as of October 1, 2013, Process Plus LLCCincinnati, OH, USAAbels, JeffreyForeign Trade Service CorpPrinceton Junction, NJ, USAAbou-Nemeh, IbrahimNovus International IncSaint Charles, MO,

67

Asian Section List  

Science Conference Proceedings (OSTI)

Name AffiliationCity, State, CountryAsian Section2013 Members122 Members as of July 1, 2013Abideen, Syed Noor UlUniversity of Agriculture PeshawarPeshawar, PakistanAdachi, ShujiKyoto UniversityKyoto, JapanAhmed, Muhammad SaadInternational Islamic Universit

68

CHAPTER CONTENTS Section Page  

E-Print Network (OSTI)

CHAPTER CONTENTS Section Page 13.1 Wooded Wetland Monitoring 13.1-1 13.2 Landfill Soils Gas Left Blank #12;Data Quality Objectives ­ Landfill Gas and Surface Leachate Monitoring Environmental Surveillance X Restoration #12;Data Quality Objectives - Landfill Gas and Surface Leachate Monitoring 13

Homes, Christopher C.

69

Small-scale alcohol fuel production  

Science Conference Proceedings (OSTI)

This is the final report of a project to demonstrate the feasibility of small-scale alcohol fuel production. A list of equipment and costs incurred in contracting the still are included. No experimental results are presented. (DMC)

Evans, J.; McQueary, J.

1983-02-25T23:59:59.000Z

70

SECTION J, APPENDIX B - PEP  

National Nuclear Security Administration (NNSA)

SECTION J APPENDIX B PERFORMANCE EVALUATION PLAN Replaced by Mods 002, 016, 020, 029 Intentionally left blank for Internet posting purposes. Section J, Appendix B, Page 1...

71

Third international symposium on alcohol fuels technology  

DOE Green Energy (OSTI)

At the opening of the Symposium, Dr. Sharrah, Senior Vice President of Continental Oil Company, addressed the attendees, and his remarks are included in this volume. The Symposium was concluded by workshops which addressed specific topics. The topical titles are as follows: alcohol uses; production; environment and safety; and socio-economic. The workshops reflected a growing confidence among the attendees that the alcohols from coal, remote natural gas and biomass do offer alternatives to petroleum fuels. Further, they may, in the long run, prove to be equal or superior to the petroleum fuels when the aspects of performance, environment, health and safety are combined with the renewable aspect of the biomass derived alcohols. Although considerable activity in the production and use of alcohols is now appearing in many parts of the world, the absence of strong, broad scale assessment and support for these fuels by the United States Federal Government was a noted point of concern by the attendees. The environmental consequence of using alcohols continues to be more benign in general than the petroleum based fuels. The exception is the family of aldehydes. Although the aldehydes are easily suppressed by catalysts, it is important to understand their production in the combustion process. Progress is being made in this regard. Of course, the goal is to burn the alcohols so cleanly that catalytic equipment can be eliminated. Separate abstracts are prepared for the Energy Data Base for individual presentations.

none,

1980-04-01T23:59:59.000Z

72

Part III - Section J  

National Nuclear Security Administration (NNSA)

H H DIVERSITY PLAN GUIDANCE To Be Updated during Transition With regard to the Contract Section I Clause entitled "Diversity Plan", this Appendix provides guidance to assist the Contractor in understanding the information being sought by the Department for each of the clause's Diversity elements. If the Contractor's current policy or procedure already addresses the following elements, the Contractor need only provide a copy of the policy or procedure to the Contracting Officer and identify the applicable policy or procedure and applicable page number(s). Work Force This Contract includes clauses on Equal Employment Opportunity (EEO) and Affirmative Action (AA). The Contractor's Diversity Plan should describe the means by which the

73

Alcohol Fuels Program technical review, Spring 1984  

DOE Green Energy (OSTI)

The alcohol fuels program consists of in-house and subcontracted research for the conversion of lignocellulosic biomass into fuel alcohols via thermoconversion and bioconversion technologies. In the thermoconversion area, the SERI gasifier has been operated on a one-ton per day scale and produces a clean, medium-Btu gas that can be used to manufacture methanol with a relatively small gas-water shift reaction requirement. Recent research has produced catalysts that make methanol and a mixture of higher alcohols from the biomass-derived synthetic gas. Three hydrolysis processes have emerged as candidates for more focused research. They are: a high-temperature, dilute-acid, plug-flow approach based on the Dartmouth reactor; steam explosion pretreatment followed by hydrolysis using the RUT-C30 fungal organism; and direct microbial conversion of the cellulose to ethanol using bacteria in a single or mixed culture. Modeling studies, including parametric and sensitivity analyses, have recently been completed. The results of these studies will lead to a better definition of the present state-of-the-art for these processes and provide a framework for establishing the research and process engineering issues that still need resolution. In addition to these modeling studies, economic feasibility studies are being carried out by commercial engineering firms. Their results will supplement and add commercial validity to the program results. The feasibility contractors will provide input at two levels: Technical and economic assessment of the current state-of-the-art in alcohol production from lignocellulosic biomass via thermoconversion to produce methanol and higher alcohol mixtures and bioconversion to produce ethanol; and identification of research areas having the potential to significantly reduce the cost of production of alcohols.

Not Available

1984-10-01T23:59:59.000Z

74

Section 180(c)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

: : Questions for Discussion * Funding Allocation Method: - Formula or needs-based? Does either choice impact a set-aside? * Eligibility: - What happens if a Tribe has no emergency response or law enforcement capability? Can they be eligible for Section 180(c) funds? Funding Allocation Method * What we've heard: - Population is not an appropriate measure for funds - Funding should protect all aboriginal lands - Don't use the ½ mile of a route measure used in the EIS - Consider a set-aside of funds for Tribes, higher than the 3% used by DOT's HMEP assistance program. Funding Allocation Method * Formula Approach - Factors in a formula should measure risk and need - What factors might be appropriate? - How can a formula account for varying levels of tribal authority over a route? For example,

75

Radiation and photochemistry section  

Science Conference Proceedings (OSTI)

The highlights of this past year in the Radiation and Photochemistry Section at Argonne include: (1) picosecond optical studies of radical cations and excited states produced in hydrocarbon radiolysis provided the first kinetic measurements of ion transformation and production of triplet and singlet excited states by ion recombination. (2) studies of radical cations of alkyl-substituted amines and sulfides provided insights into ion-molecule reactions of radical cations in the condensed phase. (3) studies of the behavior of strained alkane radical cations, such as cubane {sup +}{center dot}, revealed new rearrangements and remarkable, medium-dependent differences in their structures. (4) H{center dot}atom reactions yielding e{sub aq}{sup {minus}} provided the first reliable measurements of hydrated-electron enthalpy and entropy and forced the revision of some previous thinking about the driving force in {sub aq}{sup {minus}} reactions.

Not Available

1991-01-01T23:59:59.000Z

76

Alcohol fuel conversion apparatus for internal combustion engines  

Science Conference Proceedings (OSTI)

An alcohol fuel conversion apparatus is described for internal combustion engines comprising: fuel storage means containing an alcohol fuel; primary heat exchanger means in fluid communication with the fuel storage means for transferring heat to pressurized alcohol contained within the heat exchanger means; a heat source for heating the heat exchange means; pressure relief valve means, in closed fluid communication with the primary heat exchange means, operable to release heated pressurized alcohol into an expansion chamber; converter means, including the expansion chamber, in fluid communication with the pressure relief valve means for receiving the heated pressurized alcohol and for the vaporization of the alcohol; carburetor means in fluid communication with the converter means for metering and mixing vaporized alcohol with air for proper combustion and for feeding the mixture to an internal combustion engine; and pump means for pressurized pumping of alcohol from the fuel storage means to the heat exchanger means, converter means, carburetor means, and to the engine.

Carroll, B.I.

1987-01-13T23:59:59.000Z

77

Improved fermentative alcohol production. [Patent application  

DOE Patents (OSTI)

An improved fermentation process is described for producing alcohol which includes the combination of vacuum fermentation and vacuum distillation. Preferably, the vacuum distillation is carried out in two phases, one a fermentor proper operated at atmospheric pressure and a flash phase operated at reduced pressure with recycle of fermentation brew having a reduced alcohol content to the fermentor, using vapor recompression heating of the flash-pot recycle stream to heat the flash-pot or the distillation step, and using water load balancing (i.e., the molar ratio of water in the fermentor feed is the same as the molar ratio of water in the distillation overhead).

Wilke, C.R.; Maiorella, B.L.; Blanch, H.W.; Cysewski, G.R.

1980-11-26T23:59:59.000Z

78

Latin American Section of AOCS  

Science Conference Proceedings (OSTI)

Fats and Oils professionals from South America, Central America, Mexico and the Caribbean. Latin American Section of AOCS Sections achievement application award awards canadian distinguished division fats member membership memorial network nominat

79

Alcohols as hydrogen-donor solvents for treatment of coal  

DOE Patents (OSTI)

A method for the hydroconversion of coal by solvent treatment at elevated temperatures and pressure wherein an alcohol having an .alpha.-hydrogen atom, particularly a secondary alcohol such as isopropanol, is utilized as a hydrogen donor solvent. In a particular embodiment, a base capable of providing a catalytically effective amount of the corresponding alcoholate anion under the solvent treatment conditions is added to catalyze the alcohol-coal reaction.

Ross, David S. (Palo Alto, CA); Blessing, James E. (Menlo Park, CA)

1981-01-01T23:59:59.000Z

80

Alcohol synthesis from CO or CO.sub.2  

SciTech Connect

Methods for producing alcohols from CO or CO.sub.2 and H.sub.2 utilizing a palladium-zinc on alumina catalyst are described. Methods of synthesizing alcohols over various catalysts in microchannels are also described. Ethanol, higher alcohols, and other C.sub.2+ oxygenates can produced utilizing Rh--Mn or a Fisher-Tropsch catalyst.

Hu, Jianli [Kennewick, WA; Dagle, Robert A [Richland, WA; Holladay, Jamelyn D [Kennewick, WA; Cao, Chunshe [Houston, TX; Wang, Yong [Richland, WA; White, James F [Richland, WA; Elliott, Douglas C [Richland, WA; Stevens, Don J [Richland, WA

2010-12-28T23:59:59.000Z

Note: This page contains sample records for the topic "alcohol msds section" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


81

Alcohol fuel production training program. Final report  

Science Conference Proceedings (OSTI)

The purpose of the project was to offer instruction in the small scale production of ethanol, which can be added to gasoline by about 10%. The course was designed to help farmers in particular to make ethanol to extend fuel use. This project has four objectives. They are: (1) design an alcohol fuel production course with appropriate equipment for hands-on training; (2) offer at least three training sessions on alcohol fuel production in Cumberland County each year of the project; (3) work with the Governor's Task Force on Gasohol to disseminate the necessary information on alcohol production to the public; (4) identify, in consultation with the New Jersey Department of Energy and Agriculture, other training sites in the state and offer at least three training sessions outside of Cumberland County during the second year of the project. As of March 31, 1982, Cumberland County College completed all activities and objectives outlined in its Appropriate Technology project ''Alcohol Fuel Production.'' Given the six month extension requested to accommodate farmers in other parts of the state and the growing season, this project was completed within the stated time schedule. Although the response for the course was high in the beginning of 1981, the increased supply of low cost fuels at the end of the year probably accounts for the decline in the public's willingness to take a course of this nature.

Burke, J.

1982-06-30T23:59:59.000Z

82

Physics Out Loud - Cross Section  

NLE Websites -- All DOE Office Websites (Extended Search)

Cerenkov Light Previous Video (Cerenkov Light) Physics Out Loud Main Index Next Video (Cryomodule) Cryomodule Cross Section Jo Dudek, a jointly appointed associate professor at Old...

83

TABLE OF CONTENTS SECTION A: PREINTERVIEW OBSERVATION  

U.S. Energy Information Administration (EIA) Indexed Site

TABLE OF CONTENTS TABLE OF CONTENTS SECTION A: PREINTERVIEW OBSERVATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 SECTION B: HOUSING TYPE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 SECTION C: HOME HEATING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 SECTION D: AIR CONDITIONING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 SECTION E: WATER HEATING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 SECTION F: LIGHTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 SECTION G: APPLIANCES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Cooking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Refrigerators and Freezers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

84

Developing alternative feedstocks for fuel alcohol  

Science Conference Proceedings (OSTI)

This paper briefly reviews recent research to examine the viability of energy sorghum as a feedstock for producing fuel alcohol. Energy sorghum is the name given to any sweet sorghum shown to be feasible for producing fuel alcohol. Energy sorghum can grow on a variety of soils, in 90 day cycles, with up to three crops a year. Crop rotation is rarely needed; most of the nitrogen and potassium returns to the soil. Harmon Engineering and Testing initiated an inhouse program to research sweet sorghum development. Equipment specifications and preliminary results are given. An ''energy farm'' process is explained step by step. Stalk juice, grain, and stalk fiber yields are listed. The use of bagasse and carbon dioxide is also considered.

Verma, V.K.

1982-06-01T23:59:59.000Z

85

Limonene and tetrahydrofurfuryl alcohol cleaning agent  

DOE Patents (OSTI)

The present invention is a tetrahydrofurfuryl alcohol and limonene or terpineol cleaning agent and method for formulating and/or using the cleaning agent. This cleaning agent effectively removes both polar and nonpolar contaminants from various electrical and mechanical parts and is readily used without surfactants, thereby reducing the need for additional cleaning operations. The cleaning agent is warm water rinsable without the use of surfactants. The cleaning agent can be azeotropic, enhancing ease of use in cleaning operations and ease of recycling.

Bohnert, George W. (Harrisonville, MO); Carter, Richard D. (Lee' s Summit, MO); Hand, Thomas E. (Lee' s Summit, MO); Powers, Michael T. (Santa Rosa, CA)

1996-05-07T23:59:59.000Z

86

Limonene and tetrahydrofurfurly alcohol cleaning agent  

DOE Patents (OSTI)

The present invention is a tetrahydrofurfuryl alcohol and limonene cleaning agent and method for formulating and/or using the cleaning agent. This cleaning agent effectively removes both polar and nonpolar contaminants from various electrical and mechanical parts and is readily used without surfactants, thereby reducing the need for additional cleaning operations. The cleaning agent is warm water rinsable without the use of surfactants. The cleaning agent can be azeotropic, enhancing ease of use in cleaning operations and ease of recycling.

Bohnert, George W. (Harrisonville, MO); Carter, Richard D. (Lee' s Summit, MO); Hand, Thomas E. (Lee' s Summit, MO); Powers, Michael T. (Santa Rosa, CA)

1997-10-21T23:59:59.000Z

87

Limonene and tetrahydrofurfuryl alcohol cleaning agent  

DOE Patents (OSTI)

The present invention is a tetrahydrofurfuryl alcohol and limonene cleaning agent and method for formulating and/or using the cleaning agent. This cleaning agent effectively removes both polar and nonpolar contaminants from various electrical and mechanical parts and is readily used without surfactants, thereby reducing the need for additional cleaning operations. The cleaning agent is warm water rinsable without the use of surfactants. The cleaning agent can be azeotropic, enhancing ease of use in cleaning operations and ease of recycling.

Bohnert, G.W.; Carter, R.D.; Hand, T.E.; Powers, M.T.

1997-10-21T23:59:59.000Z

88

The Search for Genes Related to a Low-Level Response to Alcohol Determined by Alcohol Challenges  

E-Print Network (OSTI)

Background: A low level of response (LR) to alcohol seems to relate to a substantial proportion of the risk for alcoholism and to have significant heritability. Methods: This report describes the results of a genome-wide segregation analysis for the first 139 pairs of full siblings by using an alcohol challenge protocol as a direct measure of LR. Subjects from 18 to 29 years old were selected if the original screen indicated they had an alcohol-dependent parent, reported a personal history of drinking but had no evidence of alcohol dependence, and had a full sibling with similar characteristics. Body sway and Subjective High Assessment Scale scores were measured at baseline and at regular intervals after the administration of a measured dose of alcohol. Participants and available parents were genotyped for 811 microsatellite markers, and resulting data were analyzed with a variance component method. Results: Nine chromosome regions with logarithm of the odds ratio (LOD) between 2.2 and 3.2 were identified; several had previously been implicated regarding phenotypes relevant to alcoholism and the LR to alcohol. Several regions identified in the previous linkage study by using a retrospective self-report questionnaire were potentially confirmed by this study. The strongest evidence was on chromosomes 10, 11, and 22. Conclusions: Several chromosomal areas seem to relate to the low LR to alcohol as a risk factor for alcohol dependence.

Kirk C. Wilhelmsen; Marc Schuckit; Tom L. Smith; James V. Lee; Samantha K. Segall; Heidi S. Feiler; Jelger Kalmijn

2003-01-01T23:59:59.000Z

89

Separation and concentration of lower alcohols from dilute aqueous solutions  

DOE Patents (OSTI)

A process for producing, from a dilute aqueous solution of a lower (C.sub.1 -C.sub.5) alcohol, a concentrated liquid solution of the alcohol in an aromatic organic solvent is disclosed. Most of the water is removed from the dilute aqueous solution of alcohol by chilling sufficiently to form ice crystals. Simultaneously, the remaining liquid is extracted at substantially the same low temperature with a liquid organic solvent that is substantially immiscible in aqueous liquids and has an affinity for the alcohol at that temperature, causing the alcohol to transfer to the organic phase. After separating the organic liquid from the ice crystals, the organic liquid can be distilled to enrich the concentration of alcohol therein. Ethanol so separated from water and concentrated in an organic solvent such as toluene is useful as an anti-knock additive for gasoline.

Moore, Raymond H. (Richland, WA); Eakin, David E. (Kennewick, WA); Baker, Eddie G. (Richland, WA); Hallen, Richard T. (Richland, WA)

1991-01-01T23:59:59.000Z

90

Equipment Design and Cost Estimation for Small Modular Biomass Systems, Synthesis Gas Cleanup, and Oxygen Separation Equipment; Task 9: Mixed Alcohols From Syngas -- State of Technology  

DOE Green Energy (OSTI)

This deliverable is for Task 9, Mixed Alcohols from Syngas: State of Technology, as part of National Renewable Energy Laboratory (NREL) Award ACO-5-44027, ''Equipment Design and Cost Estimation for Small Modular Biomass Systems, Synthesis Gas Cleanup and Oxygen Separation Equipment''. Task 9 supplements the work previously done by NREL in the mixed alcohols section of the 2003 technical report Preliminary Screening--Technical and Economic Assessment of Synthesis Gas to Fuels and Chemicals with Emphasis on the Potential for Biomass-Derived Syngas.

Nexant Inc.

2006-05-01T23:59:59.000Z

91

The Relationship Between Tobacco, Alcohol, and Marijuana Use Among Teenagers.  

E-Print Network (OSTI)

??The purpose of this study was to explore the relationship between alcohol, tobacco, and marijuana use among teenagers. This study examined three research questions: (1) (more)

Rose, John Donald

2006-01-01T23:59:59.000Z

92

Electrocatalyst for Alcohol Oxidation at Fuel Cell Anodes - Energy ...  

Ethanol and other alcohols are nearly ideal reactants for fuel cells. Unfortunately they are difficult to oxidize, requiring breaking of carbon-carbon bonds. This ...

93

Minimally refined biomass fuel. [carbohydrate-water-alcohol mixture  

DOE Patents (OSTI)

A minimally refined fluid composition, suitable as a fuel mixture and derived from biomass material, is comprised of one or more water-soluble carbohydrates such as sucrose, one or more alcohols having less than four carbons, and water. The carbohydrate provides the fuel source; water-solubilizes the carbohydrate; and the alcohol aids in the combustion of the carbohydrate and reduces the viscosity of the carbohydrate/water solution. Because less energy is required to obtain the carbohydrate from the raw biomass than alcohol, an overall energy savings is realized compared to fuels employing alcohol as the primary fuel.

Pearson, R.K.; Hirschfeld, T.B.

1981-03-26T23:59:59.000Z

94

The effects of alcohol use on zinc status  

E-Print Network (OSTI)

Alcohol consumption has been shown to have adverse affects on bone growth and maintenance, although the mechanism has not been elucidated. The objective of this research was to look at the relationship between zinc and alcohol as a possible mechanism for the negative effects of ethanol consumption on bone health. Five studies were performed in order to analyze the effects of different types of alcohol consumption on female Sprague-Dawley rats of various ages. The animals were fed one of three diets (alcohol, pair-fed or chow). The rats were sacrificed at varying time intervals according to the specific study. Zinc analysis of the serum, femur and tibia was performed using atomic absorption spectrophotometry. The alcohol eventually affected the serum zinc status of the rats in the adolescent project. The zinc status of the animals in the moderate alcohol, 2-day binge, 5-day binge and short-term adult alcohol projects was not significantly altered due to the alcohol. A longer duration and/or a higher amount of ethanol was needed to consistently detect changes in the serum and bone zinc concentrations of all the animals. Although zinc status is altered by ethanol consumption, this relationship is not likely to be the sole mechanism behind the effects of alcohol on bone health.

Chapman, Lisa Louise

1998-01-01T23:59:59.000Z

95

Catalytic distillation for the synthesis of tertiary butyl alcohol.  

E-Print Network (OSTI)

??Catalytic Distillation for the synthesis of tertiary butyl alcohol (TBA) is investigated in this thesis. The solvent, ethylene glycol, is proposed as a means of (more)

Safinski, Tomasz

2005-01-01T23:59:59.000Z

96

Electrocatalyst for alcohol oxidation in fuel cells  

DOE Patents (OSTI)

Binary and ternary electrocatalysts are provided for oxidizing alcohol in a fuel cell. The binary electrocatalyst includes 1) a substrate selected from the group consisting of NiWO.sub.4 or CoWO.sub.4 or a combination thereof, and 2) Group VIII noble metal catalyst supported on the substrate. The ternary electrocatalyst includes 1) a substrate as described above, and 2) a catalyst comprising Group VIII noble metal, and ruthenium oxide or molybdenum oxide or a combination thereof, said catalyst being supported on said substrate.

Adzic, Radoslav R. (Setauket, NY); Marinkovic, Nebojsa S. (Coram, NY)

2001-01-01T23:59:59.000Z

97

Agricultural scientists cut alcohol fuel costs  

Science Conference Proceedings (OSTI)

Scientists at the US Department of Agriculture have succeeded in lowering the cost of making alcohol from corn by 15 cents to $1.64 per gallon. The cost of drying distillers' solubles dropped because at the end of each cooking/fermenting/distilling run, the solubles are used for cooking, cooling and fermenting in the next run. One evaporation of solubles is required after 10 runs, so energy cost is cut from 17 cents to 1.7 cents. The protein by-products recovered, can be used as swine and poultry feeds and as human food.

Not Available

1981-09-21T23:59:59.000Z

98

Process for producing fuel grade ethanol by continuous fermentation, solvent extraction and alcohol separation  

DOE Patents (OSTI)

Alcohol substantially free of water is prepared by continuously fermenting a fermentable biomass feedstock in a fermentation unit, thereby forming an aqueous fermentation liquor containing alcohol and microorganisms. Continuously extracting a portion of alcohol from said fermentation liquor with an organic solvent system containing an extractant for said alcohol, thereby forming an alcohol-organic solvent extract phase and an aqueous raffinate. Said alcohol is separated from said alcohol-organic solvent phase. A raffinate comprising microorganisms and unextracted alcohol is returned to the fermentation unit.

Tedder, Daniel W. (Marietta, GA)

1985-05-14T23:59:59.000Z

99

Alcohol and Other Drugs Office of Student Life  

E-Print Network (OSTI)

to, buy alcohol for, or furnish alcohol to anyone under 21, even if you are the parent, legal or furnishing beer or intoxicating liquor to an person under 21 years of age, or buying it for any person under,Valium) Flunitrazepam (Rohypnol) GHB Methaqualone (Quaalude) Fatigue; confusion; impaired coordination, memory, judgment

Jones, Michelle

100

Acceptorless Photocatalytic Dehydrogenation for Alcohol Decarbonylation and Imine Synthesis  

Science Conference Proceedings (OSTI)

It has come to light: Renewed interest in conversions of highly oxygenated materials has motivated studies of the organometallic-catalyzed photocatalytic dehydrogenative decarbonylation of primary alcohols into alkanes, CO, and H2 (see scheme). Methanol, ethanol, benzyl alcohol, and cyclohexanemethanol are readily decarbonylated. The photocatalysts are also active for amine dehydrogenation to give N-alkyl aldimines and H2.

Ho, Hung-An; Manna, Kuntal; Sadow, Aaron D.

2012-07-29T23:59:59.000Z

Note: This page contains sample records for the topic "alcohol msds section" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


101

Alcohol Fuel Flexibility -- Progress And Prospects  

E-Print Network (OSTI)

This paper was prepared as the result of work by a member of the staff of the California Energy Commission. It does not necessarily represent the views of the Energy Commission, its employees, or the State of California. The Energy Commission, the State of California, its employees, contractors and subcontractors make no warrant, express or implied, and assume no legal liability for the information in this paper; nor does any party represent that the uses of this information will not infringe upon privately owned rights. This paper has not been approved or disapproved by the California Energy Commission nor has the California Energy Commission passed upon the accuracy or adequacy of the information in this paper. SEPTEMBER 2005 CEC-600-2005-038 2 Alcohol Fuel Flexibility -- Progress and Prospects Thomas MacDonald California Energy Commission 1516 Ninth St. Sacramento, California 95814 Phone (916) 654-4120 FAX (916) 654-4753 e-mail: tmacdona@energy.state.ca.us Fifteenth International Symposium on Alcohol Fuels San Diego, CA September 26-28, 2005

Transportation Fuels Division; Thomas Macdonald; Thomas Macdonald

2005-01-01T23:59:59.000Z

102

Alcohol Transportation Fuels Demonstration Program. Phase 1  

DOE Green Energy (OSTI)

Hawaii has abundant natural energy resources, especially biomass, that could be used to produce alternative fuels for ground transportation and electricity. This report summarizes activities performed during 1988 to June 1991 in the first phase of the Alcohol Transportation Fuels Demonstration Program. The Alcohol Transportation Fuels Demonstration Program was funded initially by the Energy Division of the State of Hawaii`s Department of Business, Economic Development and Tourism, and then by the US Department of Energy. This program was intended to support the transition to an altemative transportation fuel, methanol, by demonstrating the use of methanol fuel and methanol-fueled vehicles, and solving the problems associated with that fuel. Specific objectives include surveying renewable energy resources and ground transportation in Hawaii; installing a model methanol fueling station; demonstrating a methanol-fueled fleet of (spark-ignition engine) vehicles; evaluating modification strategies for methanol-fueled diesel engines and fuel additives; and investigating the transition to methanol fueling. All major objectives of Phase I were met (survey of local renewable resources and ground transportation, installation of methanol refueling station, fleet demonstration, diesel engine modification and additive evaluation, and dissemination of information on alternative fueling), and some specific problems (e.g., relating to methanol fuel contamination during handling and refueling) were identified and solved. Several key issues emerging from Phase I (e.g., methanol corrosion, flame luminosity, and methanol-transition technoeconomics) were recommended as topics for follow-on research in subsequent phases of this program.

Kinoshita, C.M. [ed.

1990-12-31T23:59:59.000Z

103

WASTE DISPOSAL SECTION CORNELL UNIVERSITY  

E-Print Network (OSTI)

2/07 WASTE DISPOSAL SECTION CORNELL UNIVERSITY PROCEDURE for DISPOSAL of RADIOACTIVE MATERIALS This procedure has been developed to ensure the safety of those individuals who handle radioactive waste identified hazardous waste, or other unusual issues require special consideration. Contact the Department

Manning, Sturt

104

Environment Canada Industrial Programs Section  

E-Print Network (OSTI)

is a promoter-trap vector. Promoter-trapping cereus is ubiquitous in soil and on plant roots (Stabb involves Elite@ flow cytometer/cell sorter Section 2.6 after subculturing and at stationary phase. At each-colored transmitted light image. The apparent fusions for visualizing single cells in soil and on plantvariation

105

Section 999 Program Library | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Science & Innovation Oil & Gas Offshore Drilling Section 999 Program Library Section 999 Program Library Cost-Shared Program Publications October 2, 2013 URTAC Meeting -...

106

Symmetric Long Straight Section Lattices  

NLE Websites -- All DOE Office Websites (Extended Search)

Symmetric Symmetric Long Straight Section Lattices for 2, 4, and 8 Sectors formerly AOP-TN-2009-007, Rev. 2 Michael Borland March 23, 2009 Accelerator Systems Division, Advanced Photon Source 1 Introduction Long straight sections [1] (LSS) are anticipated to be one of the significant changes to the accel- erator as part of the APS Renewal. Previously [2], we developed a lattice with eight LSS that, while workable, would have presented some operational challenges. In the present note, we show improved results for 8LSS, along with new solutions for 4LSS and 2LSS. As before, these lattices are developed by removing the Q2 quadrupoles and moving the Q1 back into its place, permitting a 7.7-m-long insertion device (as judged by the increase in face-to-face distance for the innermost powered quadrupoles). Further increases in length (perhaps 10%) might be possible by removing corrector magnets,

107

Transverse section radionuclide scanning system  

DOE Patents (OSTI)

This invention provides a transverse section radionuclide scanning system for high-sensitivity quantification of brain radioactivity in cross-section picture format in order to permit accurate assessment of regional brain function localized in three-dimensions. High sensitivity crucially depends on overcoming the heretofore known raster type scanning, which requires back and forth detector movement involving dead-time or partial enclosure of the scan field. Accordingly, this invention provides a detector array having no back and forth movement by interlaced detectors that enclose the scan field and rotate as an integral unit around one axis of rotation in a slip ring that continuously transmits the detector data by means of laser emitting diodes, with the advantages that increased amounts of data can be continuously collected, processed and displayed with increased sensitivity according to a suitable computer program.

Kuhl, David E. (Rosemont, PA); Edwards, Roy Q. (Plymouth Township, PA)

1976-01-01T23:59:59.000Z

108

SECTION J, APPENDIX A - SOW  

National Nuclear Security Administration (NNSA)

Replaced Mod 002; Modified Mod 016; Replaced Mod 002; Modified Mod 016; Replaced Mod 029; Modified Mod 0049) Honeywell FM&T, LLC Contract No. DE-NA0000622 SECTION J APPENDIX A STATEMENT OF WORK 09/19/12 TABLE OF CONTENTS CHAPTER I. OBJECTIVES, SCOPE, AND REQUIREMENTS ......................................................................... 1 1.0 OBJECTIVE .................................................................................................................................................. 1 2.0 BACKGROUND ............................................................................................................................................ 1 2.1 The NNSA Mission ...................................................................................................................................... 1

109

Proceedings of the alcohol fuel production and utilization conference  

Science Conference Proceedings (OSTI)

A conference was held to provide farmers, businesses, industries, and specialty groups with the best available information on current and projected activities related to the production and utilization of biomass for alcohol fuels. All aspects of the alcohol fuel production and utilization process were discussed. From biomass sources, through conversion processes to end-use products and applications were topics discussed by numerous experts. Other experts took this basic information and put it together into total systems. Speakers presented overviews on alcohol fuel related activities on state, regional, and national levels. Finally, commercialization incentives, funding sources, environmental considerations, research developments, safety considerations, and regulatory requirements were discussed as factors which must be addressed when considering the production and utilization of alcohol fuels. Separate abstracts have been prepared for items within the scope of the Energy Data Base.

Not Available

1980-01-01T23:59:59.000Z

110

New diversification strategies for the Japanese alcohol industry  

E-Print Network (OSTI)

Japanese major alcoholic beverage companies, whose businesses are mainly the production and sale of beer products, stand at a strategic crossroads. There are several reasons: a slow decrease in the Japanese population, ...

Yoshimura, Toru, M.B.A. Massachusetts Institute of Technology

2007-01-01T23:59:59.000Z

111

Method for producing hydrocarbon and alcohol mixtures. [Patent application  

DOE Patents (OSTI)

It is an object of this invention to provide an efficient process for extracting alcohols and ketones from an aqueous solution containing the same into hydrocarbon fuel mixtures, such as gasoline, diesel fuel and fuel oil. Another object of the invention is to provide a mixture consisting of hydrocarbon, alcohols or ketones, polyoxyalkylene polymer and water which can be directly added to fuels or further purified. The above stated objects are achieved in accordance with a preferred embodiment of the invention by contacting an aqueous fermentation liquor with a hydrocarbon or hydrocarbon mixture containing carbon compounds having 5 to 18 carbon atoms, which may include gasoline, diesel fuel or fuel oil. The hydrocarbon-aqueous alcohol solution is mixed in the presence or one or more of a group of polyoxyalkylene polymers described in detail hereinafter; the fermentation alcohol being extracted into the hydrocarbon fuel-polyoxyalkylene polymer mixture.

Compere, A.L.; Googin, J.M.; Griffith, W.L.

1980-12-01T23:59:59.000Z

112

Electrogenerative oxidation of lower alcohols to useful products  

DOE Patents (OSTI)

In the disclosed electrogenerative process for converting alcohols such as ethanol to aldehydes such as acetaldehyde, the alcohol starting material is an aqueous solution containing more than the azeotropic amount of water. Good first-pass conversions (<40% and more typically <50%) are obtained at operating cell voltages in the range of about 80 to about 350 millivolts at ordinary temperatures and pressures by using very high flow rates of alcohol to the exposed anode surface (i.e. the "gas" side of an anode whose other surface is in contact with the electrolyte). High molar flow rates of vaporized aqueous alcohol also help to keep formation of undesired byproducts at a low level.

Meshbesher, Thomas M. (4507 Weldin Rd., Wilmington, DE 19803)

1987-01-01T23:59:59.000Z

113

DOE supported research in alcohol fuel technology development  

Science Conference Proceedings (OSTI)

The Department of Energy sponsored research in alcohol fuel technology development under the direction of Congress and Public Law 96-126. Twenty-seven research grants of about $50,000 each were funded to develop lower cost methods for alcohol fuel production. This paper discusses the objectives of the program and relates the accomplishments achieved by the research. A discussion of the highlights of several selected projects is included.

Dodds, J.

1984-01-01T23:59:59.000Z

114

Use of alcohol in farming applications: alternative fuels utilization program  

DOE Green Energy (OSTI)

The use of alcohol with diesel fuel has been investigated as a means of extending diesel fuel supplies. The ability to use ethanol in diesel-powered farm equipment could provide the means for increasing the near-term fuels self-sufficiency of the American farmer. In the longer term, the potential availability of methanol (from coal) in large quantities could serve to further decrease the dependency on diesel fuel. This document gives two separate overviews of the use of alcohols in farm equipment. Part I of this document compares alcohol with No. 1 and No. 2 diesel fuels and describes several techniques for using alcohol in farm diesels. Part II of this document discusses the use of aqueous ethanol in diesel engines, spark ignition engines and provides some information on safety and fuel handling of both methanol and ethanol. This document is not intended as a guide for converting equipment to utilize alcohol, but rather to provide information such that the reader can gain insight on the advantages and disadvantages of using alcohol in existing engines currently used in farming applications.

Borman, G.L.; Foster, D.E.; Uyehara, O.A.; McCallum, P.W.; Timbario, T.J.

1980-11-01T23:59:59.000Z

115

High-alcohol microemulsion fuel performance in a diesel engine  

DOE Green Energy (OSTI)

Incidence of methanol use in diesel engines is increasing rapidly due to the potential to reduce both diesel particulate emissions and petroleum consumption. Because simple alcohols and conventional diesel fuel are normally immiscible, most tests to date have used neat to near-neat alcohol, or blends incorporating surfactants or other alcohols. Alcohol's poor ignition quality usually necssitates the use of often expensive cetane enhancers, full-time glow plugs, or spark assist. Reported herein are results of screening tests of clear microemulsion and micellar fuels which contain 10 to 65% C{sub 1}--C{sub 4} alcohol. Ignition performance and NO emissions were measured for clear, stable fuel blends containing alcohols, diesel fuel and additives such as alkyl nitrates, acrylic acids, and several vegetable oil derivatives. Using a diesel engine calibrated with reference fuels, cetane numbers for fifty four blends were estimated. The apparent cetane numbers ranged from around 20 to above 50 with the majority between 30 and 45. Emissions of nitric oxide were measured for a few select fuels and were found to be 10 to 20% lower than No. 2 diesel fuel. 36 refs., 87 figs., 8 tabs.

West, B.H.; Compere, A.L.; Griffith, W.L.

1990-01-01T23:59:59.000Z

116

Method of forming a dianhydrosugar alcohol  

Science Conference Proceedings (OSTI)

The invention includes methods of producing dianhydrosugars. A polyol is reacted in the presence of a first catalyst to form a monocyclic sugar. The monocyclic sugar is transferred to a second reactor where it is converted to a dianhydrosugar alcohol in the presence of a second catalyst. The invention includes a process of forming isosorbide. An initial reaction is conducted at a first temperature in the presence of a solid acid catalyst. The initial reaction involves reacting sorbitol to produce 1,4-sorbitan, 3,6-sorbitan, 2,5-mannitan and 2,5-iditan. Utilizing a second temperature, the 1,4-sorbitan and 3,6-sorbitan are converted to isosorbide. The invention includes a method of purifying isosorbide from a mixture containing isosorbide and at least one additional component. A first distillation removes a first portion of the isosorbide from the mixture. A second distillation is then conducted at a higher temperature to remove a second portion of isosorbide from the mixture.

Holladay, Johnathan E. (Kennewick, WA); Hu, Jianli (Kennewick, WA); Wang, Yong (Richland, WA); Werpy, Todd A. (West Richland, WA); Zhang, Xinjie (Burlington, MA)

2010-01-19T23:59:59.000Z

117

SECTION THIRTY SEVEN Consultants Section Thirty Seven Consultants, Inc.  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

THIRTY SEVEN THIRTY SEVEN Consultants Section Thirty Seven Consultants, Inc. A California Corporation 1 DEPARTMENT OF ENERGY [OE Docket No. RRTT-IR-001] Rapid Response Team for Transmission AGENCY: Office of Electricity Delivery and Energy Reliability, Department of Energy, DoE. ACTION: Request for information. (1) The development timelines for generation and attendant transmission are often not coordinated or run concurrently. Because of the lengthy time to obtain regulatory reviews, permits and approvals (collectively ''Regulatory Permits''), major new transmission lines can take significantly longer to develop than some types of generation to which the transmission would connect. This Request for Information will refer to the difference in development times between generation and transmission as

118

Clean Air Act, Section 309  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

CLEAN AIR ACT § 309* CLEAN AIR ACT § 309* §7609. Policy review (a) The Administrator shall review and comment in writing on the environmental impact of any matter relating to duties and responsibilities granted pursuant to this chapter or other provisions of the authority of Administrator, contained in any (1) legislation proposed by any Federal department or agency, (2) newly authorized Federal projects for construction and any major Federal agency action (other than a project for construction) to which section 4332(2)(C) of this title applies, and (3) proposed regulations published by any department or agency of the Federal Government. Such written comment shall be made public at the conclusion of any such review. (b) In the event the Administrator determines that any such legislation, action, or regulation

119

Section 7 | OpenEI Community  

Open Energy Info (EERE)

Contributor 4 September, 2012 - 22:36 Idaho Meeting 2 endangered species Fauna Fish and Wildlife Flora FWS Section 12 Section 7 The second Idaho GRR meeting was held today...

120

Section 12 | OpenEI Community  

Open Energy Info (EERE)

Contributor 4 September, 2012 - 22:36 Idaho Meeting 2 endangered species Fauna Fish and Wildlife Flora FWS Section 12 Section 7 The second Idaho GRR meeting was held today...

Note: This page contains sample records for the topic "alcohol msds section" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


121

Neutron cross sections: Book of curves  

Science Conference Proceedings (OSTI)

Neuton Cross Sections: Book of Curves represents the fourth edition of what was previously known as BNL-325, Neutron Cross Sections, Volume 2, CURVES. Data is presented only for (i.e., intergrated) reaction cross sections (and related fission parameters) as a function of incident-neutron energy for the energy range 0.01 eV to 200 MeV. For the first time, isometric state production cross sections have been included. 11 refs., 4 figs.

McLane, V.; Dunford, C.L.; Rose, P.F.

1988-01-01T23:59:59.000Z

122

Geothermal source potential and utilization for alcohol production  

DOE Green Energy (OSTI)

A study was conducted to assess the technical and economic feasibility of using a potential geothermal source to drive a fuel grade alcohol plant. Test data from the well at the site indicated that the water temperature at approximately 8500 feet should approach 275/sup 0/F. However, no flow data was available, and so the volume of hot water that can be expected from a well at this site is unknown. Using the available data, numerous fuel alcohol production processes and various heat utilization schemes were investigated to determine the most cost effective system for using the geothermal resource. The study found the direct application of hot water for alcohol production based on atmospheric processes using low pressure steam to be most cost effective. The geothermal flow rates were determined for various sizes of alcohol production facility using 275/sup 0/F water, 235/sup 0/F maximum processing temperature, 31,000 and 53,000 Btu per gallon energy requirements, and appropriate process approach temperatures. It was determined that a 3 million gpy alcohol plant is the largest facility that can practically be powered by the flow from one large geothermal well. An order-of-magnitude cost estimate was prepared, operating costs were calculated, the economic feasibility of the propsed project was examined, and a sensitivity analysis was performed.

Austin, J.C.

1981-11-01T23:59:59.000Z

123

Modeling and cold start in alcohol-fueled engines  

DOE Green Energy (OSTI)

Neat alcohol fuels offer several benefits over conventional gasoline in automotive applications. However, their low vapor pressure and high heat of vaporization make it difficult to produce a flammable vapor composition from a neat alcohol fuel during a start under cold ambient conditions. Various methods have been introduced to compensate for this deficiency. In this study, the authors applied computer modeling and simulation to evaluate the potential of four cold-start technologies for engines fueled by near-neat alcohol. The four technologies were a rich combustor device, a partial oxidation reactor, a catalytic reformer, and an enhanced ignition system. The authors ranked the competing technologies by their ability to meet two primary criteria for cold starting an engine at {minus}25 deg C and also by several secondary parameters related to commercialization. Their analysis results suggest that of the four technologies evaluated, the enhanced ignition system is the best option for further development.

Markel, A.J.; Bailey, B.K.

1998-05-01T23:59:59.000Z

124

State of California BOARD OF EQUALIZATION ALCOHOLIC BEVERAGE TAX REGULATIONS  

E-Print Network (OSTI)

Samples and donations of alcoholic beverages shall be reported as sales. Each transfer of samples between licensees authorized to possess alcoholic beverages on which the California state alcoholic beverages taxes have not been paid (manufacturers, manufacturers agents, distilled spirits wholesalers and rectifiers) shall be on an ex-tax basis, and shall be recorded on an invoice marked: Samples. Distilled spirits taxpayers receiving samples from other licensees in California shall record the receipt in form BOE-241-A. Samples received by direct importation shall be recorded in form BOE-242-A. Distilled spirits picked up at the licensed premises of a distilled spirits rectifier or wholesaler by a representative of a manufacturer or of a manufacturers agent to be used by him for sampling purposes, shall not be considered to be a transfer of samples between the licensees referred to in the second paragraph of this rule. Such deliveries of distilled

Regulation Treated; As Sales

1955-01-01T23:59:59.000Z

125

Alcohol Use among Restaurant Workers: An Examination of the Impact of Work-related Stress and Workplace Culture.  

E-Print Network (OSTI)

??Despite reports indicating high levels of alcohol use in the restaurant industry, little research has examined alcohol use among restaurant workers in an in depth (more)

Rocheleau, Gregory Christopher

2008-01-01T23:59:59.000Z

126

STEP 1: TO BE COMPLETED BY ALCOHOL TECHNICIAN  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

7 (07/03) OMB Control No. 1910-5122 7 (07/03) OMB Control No. 1910-5122 U.S. Department of Energy (DOE) Human Reliability Program (HRP) Alcohol Testing Form (Instructions for completing this form are attached.) STEP 1: TO BE COMPLETED BY ALCOHOL TECHNICIAN A. Employee Name __________________________________________________________________ (Print) First M.I. Last B. Employee ID No. __________________________________________________________ C. Employer Name __________________________________________________________ _____________________________________(____)________________ HRP Supervisor Phone Number D. Reason for Test: Random Reasonable Susp. Post-Accident Return to Duty Follow-up Pre-employment

127

Elastic sectional stress analysis of variable section piers subjected to three-dimensional loads  

Science Conference Proceedings (OSTI)

The elastic stress analysis of beam-column structures of uniaxial symmetrical variable cross-sections is developed using an extension of Euler-Bernoulli beam theory. The applied loads are general considering axial (P), flexure (M"x-M"y), shear (V"x-V"y), ... Keywords: Elastic sectional analysis, Shear stress, Tapered section, Three-dimensional loads, Variable section, Warping function

Lucian Stefan; Pierre Lger

2012-01-01T23:59:59.000Z

128

Alcohol production from various enzyme-converted starches with or without cooking  

Science Conference Proceedings (OSTI)

The effectiveness of alcoholic fermentation was compared by measuring alcoholic yields from various starch mashes, both cooked and uncooked. Alcohol yields from cooked and liquefied starch by bacterial ..cap alpha..-amylase were 93.9% for corn, 92.0% for cassava, 90.6% for potato, and 73.0% for babassu, whereas alcohol yields from raw starch were 90.0% for corn, 89.0% for cassava, 48.9% for babassu, and 11.4% for potato. (JMT)

Park, Y.K.; Rivera, B.C.

1982-02-01T23:59:59.000Z

129

Continuous Flow Oxidation of Alcohols and Aldehydes Utilizing Bleach and Catalytic Tetrabutylammonium Bromide  

E-Print Network (OSTI)

We report a method for the oxidation of a range of alcohols and aldehydes utilizing a simple flow system of alcohols in EtOAc with a stream of 12.5% NaOCl and catalytic Bu[subscript 4]NBr. Secondary alcohols are oxidized ...

Leduc, Andrew B.

130

Vertically stabilized elongated cross-section tokamak  

SciTech Connect

This invention provides a vertically stabilized, non-circular (minor) cross-section, toroidal plasma column characterized by an external separatrix. To this end, a specific poloidal coil means is added outside a toroidal plasma column containing an endless plasma current in a tokamak to produce a rectangular cross-section plasma column along the equilibrium axis of the plasma column. By elongating the spacing between the poloidal coil means the plasma cross-section is vertically elongated, while maintaining vertical stability, efficiently to increase the poloidal flux in linear proportion to the plasma cross-section height to achieve a much greater plasma volume than could be achieved with the heretofore known round cross-section plasma columns. Also, vertical stability is enhanced over an elliptical cross-section plasma column, and poloidal magnetic divertors are achieved.

Sheffield, George V. (Hopewell, NJ)

1977-01-01T23:59:59.000Z

131

Expandable mixing section gravel and cobble eductor  

DOE Patents (OSTI)

In a hydraulically powered pump for excavating and transporting slurries in hich it is immersed, the improvement of a gravel and cobble eductor including an expandable mixing section, comprising: a primary flow conduit that terminates in a nozzle that creates a water jet internal to a tubular mixing section of the pump when water pressure is applied from a primary supply flow; a tubular mixing section having a center line in alignment with the nozzle that creates a water jet; a mixing section/exit diffuser column that envelopes the flexible liner; and a secondary inlet conduit that forms an opening at a bas portion of the column and adjacent to the nozzle and water jet to receive water saturated gravel as a secondary flow that mixes with the primary flow inside of the mixing section to form a combined total flow that exits the mixing section and decelerates in the exit diffuser.

Miller, Arthur L. (Kenyon, MN); Krawza, Kenneth I. (Lakeville, MN)

1997-01-01T23:59:59.000Z

132

Methods for sequestering carbon dioxide into alcohols via gasification fermentation  

SciTech Connect

The present invention is directed to improvements in gasification for use with synthesis gas fermentation. Further, the present invention is directed to improvements in gasification for the production of alcohols from a gaseous substrate containing at least one reducing gas containing at least one microorganism.

Gaddy, James L; Ko, Ching-Whan; Phillips, J. Randy; Slape, M. Sean

2013-11-26T23:59:59.000Z

133

Section D: SPACE HEATING - Energy Information Administration  

U.S. Energy Information Administration (EIA)

2001 Residential Energy Consumption Survey Form EIA-457A (2001)--Household Questionnaire OMB No.: 1905-0092, Expiring February 29, 2004 19 Section D: SPACE HEATING

134

Guest editorial special section on RFID  

E-Print Network (OSTI)

The eight articles in this special section describe state-of-the-art technologies and tools and one application of RFID.

Sarma, Sanjay Emani

135

Section E: WATER HEATING - Energy Information Administration  

U.S. Energy Information Administration (EIA)

2001 Residential Energy Consumption Survey Form EIA-457A (2001)--Household Questionnaire OMB No.: 1905-0092, Expiring February 29, 2004 24 Section E: WATER HEATING

136

NIST: Electron-Impact Cross Section Database  

Science Conference Proceedings (OSTI)

... of molecules by electron impact. The database also includes cross sections for some atoms and energy distributions of ejected electrons for H, He ...

2011-12-09T23:59:59.000Z

137

O A L Section 2. Coal  

U.S. Energy Information Administration (EIA)

Section 2. Coal Coal prices are developed for the following three categories: coking coal; steam coal (all noncoking coal); and coal coke imports and exports.

138

Neutrino absortion cross sections in supernova environment  

E-Print Network (OSTI)

We study charged-current neutrino cross sections on neutronrich nuclei in the mass $A\\sim60$ region. Special attention is paid to environmental effects, i.e. finite temperature and density, on the cross sections. As these effects are largest for small neutrino energies, it is sufficient to study only the Gamow-Teller (GT) contributions to the cross sections. The relevant GT strength distributions are derived from large-scale shell model calculations. We find that the low-energy cross sections are enhanced at finite temperatures. However, for $(\

J. M. Sampaio; K. Langanke; G. Martinez-Pinedo

2001-04-04T23:59:59.000Z

139

Section B: KITCHEN APPLIANCES - Energy Information Administration  

U.S. Energy Information Administration (EIA)

2001 Residential Energy Consumption Survey Form EIA-457A (2001)--Household Questionnaire OMB No.: 1905-0092, Expiring February 29, 2004 6 Section B: KITCHEN APPLIANCES

140

GRR/Section 14-CA-d - Section 401 Water Quality Certification | Open Energy  

Open Energy Info (EERE)

GRR/Section 14-CA-d - Section 401 Water Quality Certification GRR/Section 14-CA-d - Section 401 Water Quality Certification < GRR Jump to: navigation, search GRR-logo.png GEOTHERMAL REGULATORY ROADMAP Roadmap Home Roadmap Help List of Sections Section 14-CA-d - Section 401 Water Quality Certification 14CADSection401WaterQualityCertification (1).pdf Click to View Fullscreen Contact Agencies California State Water Resources Control Board Regulations & Policies Section 401 Clean Water Act (33 U.S.C. 1251 et seq.) Porter-Cologne Water Quality Control Act Code of Regulations Title 23, Section 3855 et. seq. Triggers None specified Click "Edit With Form" above to add content 14CADSection401WaterQualityCertification (1).pdf Error creating thumbnail: Page number not in range. Error creating thumbnail: Page number not in range.

Note: This page contains sample records for the topic "alcohol msds section" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


141

GRR/Section 11-FD-a - NHPA Section 106 - Resource Survey | Open Energy  

Open Energy Info (EERE)

11-FD-a - NHPA Section 106 - Resource Survey 11-FD-a - NHPA Section 106 - Resource Survey < GRR Jump to: navigation, search GRR-logo.png GEOTHERMAL REGULATORY ROADMAP Roadmap Home Roadmap Help List of Sections Section 11-FD-a - NHPA Section 106 - Resource Survey 11-FD-a NHPA Section 106 Consultation.pdf Click to View Fullscreen Contact Agencies Advisory Council on Historic Preservation National Park Service Bureau of Indian Affairs Regulations & Policies National Historic Preservation Act 36 CFR Part 800 Triggers None specified Click "Edit With Form" above to add content 11-FD-a NHPA Section 106 Consultation.pdf 11-FD-a NHPA Section 106 Consultation.pdf Error creating thumbnail: Page number not in range. Error creating thumbnail: Page number not in range. Flowchart Narrative Section 106 applies when two thresholds are met:

142

GRR/Section 17-FD-a - Wild & Scenic Rivers Section 7(a) | Open Energy  

Open Energy Info (EERE)

GRR/Section 17-FD-a - Wild & Scenic Rivers Section 7(a) GRR/Section 17-FD-a - Wild & Scenic Rivers Section 7(a) < GRR Jump to: navigation, search GRR-logo.png GEOTHERMAL REGULATORY ROADMAP Roadmap Home Roadmap Help List of Sections Section 17-FD-a - Wild & Scenic Rivers Section 7(a) 17FDAWildScenicRiversSection7AProcess.pdf Click to View Fullscreen Contact Agencies National Park Service Bureau of Land Management United States Forest Service United States Forest Service Federal Energy Regulatory Commission Regulations & Policies Wild and Scenic Rivers Act 36 CFR 297 Wild and Scenic Rivers Triggers None specified Click "Edit With Form" above to add content 17FDAWildScenicRiversSection7AProcess.pdf Error creating thumbnail: Page number not in range. Error creating thumbnail: Page number not in range.

143

GRR/Section 14-NV-d - Section 401 Water Quality Certification | Open Energy  

Open Energy Info (EERE)

GRR/Section 14-NV-d - Section 401 Water Quality Certification GRR/Section 14-NV-d - Section 401 Water Quality Certification < GRR Jump to: navigation, search GRR-logo.png GEOTHERMAL REGULATORY ROADMAP Roadmap Home Roadmap Help List of Sections Section 14-NV-d - Section 401 Water Quality Certification 14NVDSection401WaterQualityCertification.pdf Click to View Fullscreen Contact Agencies Nevada Division of Environmental Protection Regulations & Policies Section 401 of the Clean Water Act (33 U.S.C. 1341) Triggers None specified Click "Edit With Form" above to add content 14NVDSection401WaterQualityCertification.pdf Error creating thumbnail: Page number not in range. Error creating thumbnail: Page number not in range. Error creating thumbnail: Page number not in range. Flowchart Narrative Section 401 of the Clean Water Act (33 U.S.C. 1341) requires activities in

144

GRR/Section 14-WA-d - Section 401 Water Quality Certification | Open Energy  

Open Energy Info (EERE)

GRR/Section 14-WA-d - Section 401 Water Quality Certification GRR/Section 14-WA-d - Section 401 Water Quality Certification < GRR Jump to: navigation, search GRR-logo.png GEOTHERMAL REGULATORY ROADMAP Roadmap Home Roadmap Help List of Sections Section 14-WA-d - Section 401 Water Quality Certification 14-WA-d - 401 Water Quality Certification.pdf Click to View Fullscreen Contact Agencies U S Army Corps of Engineers Washington State Department of Ecology Regulations & Policies Revised Statute of Washington Chapter 90.48 Washington Administrative Code Chapter 173-201A Washington Administrative Code 173-225-030 Triggers None specified Developers requiring a Section 404 Dredge and Fill Permit from the U S Army Corps of Engineers (Corps) are required to obtain a Section 401 Water Quality Certification from the state of Washington. The Washington State

145

GRR/Section 14-UT-d - Section 401 Water Quality Certification | Open Energy  

Open Energy Info (EERE)

GRR/Section 14-UT-d - Section 401 Water Quality Certification GRR/Section 14-UT-d - Section 401 Water Quality Certification < GRR Jump to: navigation, search GRR-logo.png GEOTHERMAL REGULATORY ROADMAP Roadmap Home Roadmap Help List of Sections Section 14-UT-d - Section 401 Water Quality Certification 14-UT-d - Section 401 Water Quality Certification.pdf Click to View Fullscreen Triggers None specified Section 401 of the Clean Water Act (CWA) requires a Water Quality Certification for any federal license or permit that is issued to construct or operate a facility, which may result in any fill or discharge into the navigable waters of the United States. The Utah Division of Water Quality oversees the 401 Water Quality Certification process in the state of Utah. The director of the Utah Division of Water Quality ("director") handles

146

The Solar System Section 4 CCoommeettss  

E-Print Network (OSTI)

orbits closer to the sun and begins to heat up. The comet's tail is formed when the solar wind forces, Lego buildings, trees, cars, aliens Chart paper Computer Power Point Presentation: Our Solar SystemSection 4 The Solar System Section 4 CCoommeettss Activity 16:Activity 16: Crazy Comets Goal

Weston, Ken

147

Heat exchanger with a removable tube section  

DOE Patents (OSTI)

A heat exchanger is described in which the tube sheet is secured against primary liquid pressure, but which allows for easy removal of the tube section. The tube section is supported by a flange which is secured by a number of shear blocks, each of which extends into a slot which is immovable with respect to the outer shell of the heat exchanger. (auth)

Wolowodiuk, W.; Anelli, J.

1975-07-29T23:59:59.000Z

148

H. W. Laboratory manual: 100 Area section  

SciTech Connect

The purpose of this manual is to present a Hazard Breakdown of all jobs normally encountered in the laboratory work of the three sections comprising the Analytic Section, Metallurgy and Control Division of the Technical Department. A Hazard Breakdown is a careful analysis of any job in which the source of possible dangers is clearly indicated for each particular step. The analysis is prepared by individuals who are thoroughly familiar with the specific job or procedure. It is felt that if the hazards herein outlined are recognized by the Laboratory personnel and the suggested safety cautions followed, the chance for injury will be minimized and the worker will become generally more safety conscious. The manual, which is prefaced by the general safety rules applying to all the laboratories, is divided into three main sections, one for each of the three sections into which the Laboratories Division is divided. These sections are as follows: Section 1 -- 200 Area Control; Section 2 -- 100 Area Control; Section 3 -- 300 Area Control, Essential Materials, and Methods Improvement.

1950-07-01T23:59:59.000Z

149

Plasma Concentrations of/3-Endorphin, Adrenocorticotropic Hormone, and Cortisol in Drinking and Abstinent Chronic Alcoholics  

E-Print Network (OSTI)

concentrations of l~-endorphin, adrenocorticotropic hormone, and cortisol in drinking and abstinent chronic alcoholics. ALCOHOL 12(6) 525-529, 1995.-Previous studies of the relationship between the endogenous opioid system and alcohol consumption have reported contradictory results. To shed light on this connection, we compared plasma concentrations of B-endorphin, adrenocorticotropic hormone, and cortisol in 70 alcoholic persons after different periods of abstinence and a group of 80 control subjects. Plasma B-endorphin was decreased in alcoholics (18.61 _+ 1.38 vs. 39.31 + 3.44 pg/ml), even after more than 10 years ' abstinence. This effect may be mediated by the tetrahydroisoquinoline system, and may thus result from chronic alcohol consumption. On the other hand, lowered circulating concentrations of/3-endorphin may be a cause, rather than an effect, of alcoholism. Plasma levels of adrenocorticotropic hormone and cortisol did not differ in alcoholics and controls (19.29 1.66 vs. 13.27 _+ 1.85 pg/ml for ACTH, 20.37 ~ 0.78 vs. 17.22 _ 0.64 ng/ml for cortisol), and thus appear to have no relation with chronic alcohol consumption. Adrenocorticotropic hormone Alcoholism /3-Endorphins Cortisol Tetrahydroisoquinolines THE RELATIONSHIP between alcohol consumption, abuse, and dependence, and the endogenous opioid system (EOS) has been investigated frequently (7,8,10,24,28,34). Although the findings have been contradictory, it nonetheless appears clear

J. L. Del Arbol; L J. C. Aguirre; J. Raya; J. Rico; M. E. Ruiz-requenat; M. T. Miranda

1995-01-01T23:59:59.000Z

150

Section 999: Annual Plans | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Section 999: Annual Plans Section 999: Annual Plans Section 999: Annual Plans October 2, 2013 URTAC Meeting - October 2013 Federal Register Notice for October 10, 2013 URTAC Meeting The 24th Meeting of the Unconventional Resources Technology Advisory Committee (URTAC), previously scheduled for October 10, 2013, is postponed until further notice due to a lapse in Federal funding. October 2, 2013 UDAC Meeting - October 2013 Federal Register Notice for October 8, 2013 UDAC Meeting The 24th Meeting of the Ultra-Deepwater Advisory Committee (UDAC), previously scheduled for October 8, 2013, is postponed until further notice due to a lapse in Federal funding. September 10, 2013 Draft 2014 Annual Plan Section 999: Draft 2014 Annual Plan July 8, 2013 2013 Annual Plan Section 999: 2013 Annual Plan

151

CenterLineBowles Center for Alcohol Studies School of Medicine, University of North Carolina at Chapel Hill  

E-Print Network (OSTI)

the National Institute of Alcohol Abuse and Alcoholism--is designed for middle-school and high-school scienceCenterLineBowles Center for Alcohol Studies School of Medicine, University of North Carolina grant to develop a second science-based curriculum. Designed for high-school students,Fetal Alcohol

Crews, Stephen

152

GRR/Section 14-HI-d - Section 401 Water Quality Certification | Open Energy  

Open Energy Info (EERE)

HI-d - Section 401 Water Quality Certification HI-d - Section 401 Water Quality Certification < GRR Jump to: navigation, search GRR-logo.png GEOTHERMAL REGULATORY ROADMAP Roadmap Home Roadmap Help List of Sections Section 14-HI-d - Section 401 Water Quality Certification 14HID - Section401WaterQualityCertification (1).pdf Click to View Fullscreen Contact Agencies Hawaii Department of Health Clean Water Branch United States Environmental Protection Agency Regulations & Policies Clean Water Act (33 U.S.C. 1251) Section 401 Hawaii Administrative Rules Title 11, Chapter 54 Triggers None specified Click "Edit With Form" above to add content 14HID - Section401WaterQualityCertification (1).pdf Error creating thumbnail: Page number not in range. Error creating thumbnail: Page number not in range. Error creating thumbnail: Page number not in range.

153

Mixed Alcohol Synthesis Catalyst Screening 2007 Progress Report  

DOE Green Energy (OSTI)

Pacific Northwest National Laboratory (PNNL) and National Renewable Energy Laboratory (NREL) are researching the feasibility of producing mixed alcohols from biomass-derived synthesis gas (syngas). PNNL is obtaining commercially available mixed alcohol or preparing promising mixed-alcohol catalysts and screening them in a laboratory-scale reactor system. The most promising catalysts are provided to NREL for testing using a slipstream from a pilot-scale biomass gasifier. After a review of the literature in 2006 and conversations with companies that produce catalysts, it was determined that no commercial mixed-alcohol synthesis catalysts were available. One manufacturer supplied a modified methanol catalyst that was tested in the PNNL laboratory-scale system and provided to NREL for further testing. PNNL also prepared and tested the behavior of 10 other catalysts representing the distinct catalyst classes for mixed alcohol syntheses. Based on those results,testing in 2007 focused on the performance of the rhodium-based catalysts. The effects of adding promoters to the rhodium catalysts in addition to the manganese already being used were examined. The iron and rhenium promoters both stood out as achieving higher carbon selectivities , followed by Cu. Iridium and Li, on the other hand, had low carbon selectivity ratios of 0.27 and 0.22, respectively. Although testing of candidate promoters is not complete, it appears that Ir and Li promoters warrant further optimization and possibly combination to further improve STYs and carbon selectivities to C2+ oxygenates. However, using these promoters, it will be necessary to incorporate a separate hydrogenation catalyst to improve the yield of C2+ alcohols with respect to the other oxygenates. Fe, Re, and Cu stand out as possible candidates in this respect, but additional research is needed to examine whether they can be combined with the other promoters on the Rh-based catalyst or need to be optimized on a separate catalyst support that is either physically mixed or used in series with the promoted Rh-based catalyst.

Gerber, Mark A.; White, J. F.; Gray, Michel J.; Stevens, Don J.

2007-11-01T23:59:59.000Z

154

Appendix: Selected Answers Section 1.2  

E-Print Network (OSTI)

Appendix: Selected Answers Chapter 1 Section 1.2 1.2.1 (a) 5/6. (b) 1. (c) 1/2. 1.2.4 No. 1.2.8 No/4. 1.6.3 limn P(An) = P(A) = P(S) = 1. 1 #12;2 APPENDIX: SELECTED ANSWERS Chapter 2 Section 2.1 2.1.1(a Negative Binomial(r + s, ) . Section 2.4 2.4.1 (a) P(U 0) = 0. (b) P(U = 1/2) = 0. (c) P(U

Rosenthal, Jeffrey S.

155

Renewable Hydrogen Production Using Sugars and Sugar Alcohols (Presentation)  

NLE Websites -- All DOE Office Websites (Extended Search)

Working Group Meeting Working Group Meeting 11/06/2007 Renewable Hydrogen Production Using Renewable Hydrogen Production Using Sugars and Sugar Alcohols Sugars and Sugar Alcohols * * Problem: Problem: Need Need to develop renewable to develop renewable hydrogen production technologies using hydrogen production technologies using diverse diverse feedstocks feedstocks 10 15 20 CH 4 : C 6 H 14 ln(P) * * Description: Description: The BioForming The BioForming TM TM process uses process uses aqueous phase reforming to cost effectively aqueous phase reforming to cost effectively produce hydrogen from a range of feedstocks, produce hydrogen from a range of feedstocks, including glycerol and sugars. The key including glycerol and sugars. The key breakthrough is a proprietary catalyst that breakthrough is a proprietary catalyst that

156

Report to the Congress: strategic alcohol fuel reserve  

Science Conference Proceedings (OSTI)

The feasibility of developing a Strategic Alcohol Fuel Reserve (SAFURE) is examined in this report. The analysis compares each of three different ethanol storage program options to that portion of the currently-planned Strategic Petroleum Reserve (SPR) which could be replaced by a particular SAFURE program. These options are: Ethanol Spare Production Capacity Utilization using essentially uneconomical, existing production capacity; Market Diversion through government purchases of ethanol for SAFURE storage, and Dedicated Plants using federal contracts to procure the entire output of five new plants. Based on this most recent analysis and other information currently available, it was concluded that the costs of acquiring, storing and managing an alcohol fuel reserve are substantially higher than the costs of the current SPR program. The net economic and security benefits of the current SPR program are also higher, and the budget costs of the SPR program are lower.

Not Available

1982-12-31T23:59:59.000Z

157

Electrocatalyst for alcohol oxidation at fuel cell anodes  

DOE Patents (OSTI)

In some embodiments a ternary electrocatalyst is provided. The electrocatalyst can be used in an anode for oxidizing alcohol in a fuel cell. In some embodiments, the ternary electrocatalyst may include a noble metal particle having a surface decorated with clusters of SnO.sub.2 and Rh. The noble metal particles may include platinum, palladium, ruthenium, iridium, gold, and combinations thereof. In some embodiments, the ternary electrocatalyst includes SnO.sub.2 particles having a surface decorated with clusters of a noble metal and Rh. Some ternary electrocatalysts include noble metal particles with clusters of SnO.sub.2 and Rh at their surfaces. In some embodiments the electrocatalyst particle cores are nanoparticles. Some embodiments of the invention provide a fuel cell including an anode incorporating the ternary electrocatalyst. In some aspects a method of using ternary electrocatalysts of Pt, Rh, and SnO.sub.2 to oxidize an alcohol in a fuel cell is described.

Adzic, Radoslav (East Setauket, NY); Kowal, Andrzej (Cracow, PL)

2011-11-02T23:59:59.000Z

158

Alcohol-free alkoxide process for containing nuclear waste  

DOE Patents (OSTI)

Disclosed is a method of containing nuclear waste. A composition is first prepared of about 25 to about 80%, calculated as SiO.sub.2, of a partially hydrolyzed silicon compound, up to about 30%, calculated as metal oxide, of a partially hydrolyzed aluminum or calcium compound, about 5 to about 20%, calculated as metal oxide, of a partially hydrolyzed boron or calcium compound, about 3 to about 25%, calculated as metal oxide, of a partially hydrolyzed sodium, potassium or lithium compound, an alcohol in a weight ratio to hydrolyzed alkoxide of about 1.5 to about 3% and sufficient water to remove at least 99% of the alcohol as an azeotrope. The azeotrope is boiled off and up to about 40%, based on solids in the product, of the nuclear waste, is mixed into the composition. The mixture is evaporated to about 25 to about 45% solids and is melted and cooled.

Pope, James M. (Monroeville, PA); Lahoda, Edward J. (Edgewood, PA)

1984-01-01T23:59:59.000Z

159

Process for reducing organic compounds with calcium, amine, and alcohol  

DOE Patents (OSTI)

Olefins are produced by contacting an organic compound having at least one benzene ring with calcium metal, ethylenediamine, a low molecular weight aliphatic alcohol, and optionally a low molecular weight aliphatic primary amine, and/or an inert, abrasive particulate substance. The reduction is conducted at temperatures ranging from about -10.degree. C. to about 30.degree. C. or somewhat higher. Substantially all of the organic compounds are converted to corresponding cyclic olefins, primarily diolefins.

Benkeser, Robert A. (West Lafayette, IN); Laugal, James A. (Lostant, IL); Rappa, Angela (Baltimore, MD)

1985-01-01T23:59:59.000Z

160

Process for reducing organic compounds with calcium, amine, and alcohol  

DOE Patents (OSTI)

Olefins are produced by contacting an organic compound having at least one benzene ring with calcium metal, ethylenediamine, a low molecular weight aliphatic alcohol, and optionally a low molecular weight aliphatic primary amine, and/or an inert, abrasive particulate substance. The reduction is conducted at temperatures ranging from about [minus]10 C to about 30 C or somewhat higher. Substantially all of the organic compounds are converted to corresponding cyclic olefins, primarily diolefins.

Benkeser, R.A.; Laugal, J.A.; Rappa, A.

1985-08-06T23:59:59.000Z

Note: This page contains sample records for the topic "alcohol msds section" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


161

GRR/Section 14-MT-d - Section 401 Water Quality Certification | Open Energy  

Open Energy Info (EERE)

GRR/Section 14-MT-d - Section 401 Water Quality Certification GRR/Section 14-MT-d - Section 401 Water Quality Certification < GRR Jump to: navigation, search GRR-logo.png GEOTHERMAL REGULATORY ROADMAP Roadmap Home Roadmap Help List of Sections Section 14-MT-d - Section 401 Water Quality Certification 14MTD401WaterQualityCertification (2).pdf Click to View Fullscreen Contact Agencies Montana Department of Environmental Quality Regulations & Policies Federal Clean Water Act (33 USC § 1251 et seq.) Montana Codes Annotated 75-5-401 Aministrative Rules of Montana Chapter 30 Administrative Rules of Montana 17.30.101 through 109 Triggers None specified Click "Edit With Form" above to add content 14MTD401WaterQualityCertification (2).pdf Error creating thumbnail: Page number not in range. Error creating thumbnail: Page number not in range.

162

GRR/Section 14-OR-d - Section 401 Water Quality Certification | Open Energy  

Open Energy Info (EERE)

GRR/Section 14-OR-d - Section 401 Water Quality Certification GRR/Section 14-OR-d - Section 401 Water Quality Certification < GRR Jump to: navigation, search GRR-logo.png GEOTHERMAL REGULATORY ROADMAP Roadmap Home Roadmap Help List of Sections Section 14-OR-d - Section 401 Water Quality Certification 14ORDSection410WaterQualityCertification.pdf Click to View Fullscreen Contact Agencies Oregon Department of Environmental Quality U S Army Corps of Engineers Regulations & Policies OAR 340-048: Certification of Compliance with Water Quality Requirements Triggers None specified Click "Edit With Form" above to add content 14ORDSection410WaterQualityCertification.pdf Error creating thumbnail: Page number not in range. Error creating thumbnail: Page number not in range. Error creating thumbnail: Page number not in range.

163

GRR/Section 14-ID-d - Section 401 Water Quality Certification | Open Energy  

Open Energy Info (EERE)

GRR/Section 14-ID-d - Section 401 Water Quality Certification GRR/Section 14-ID-d - Section 401 Water Quality Certification < GRR Jump to: navigation, search GRR-logo.png GEOTHERMAL REGULATORY ROADMAP Roadmap Home Roadmap Help List of Sections Section 14-ID-d - Section 401 Water Quality Certification 14IDDSection401WaterQualityCertificationProcess.pdf Click to View Fullscreen Contact Agencies Idaho Department of Environmental Quality United States Environmental Protection Agency U S Army Corps of Engineers Regulations & Policies Idaho Environmental Protection and Health Act Idaho Administrative Procedure Act Triggers None specified Click "Edit With Form" above to add content 14IDDSection401WaterQualityCertificationProcess.pdf 14IDDSection401WaterQualityCertificationProcess.pdf Error creating thumbnail: Page number not in range.

164

GRR/Section 14-AK-d - Section 401 Water Quality Certification | Open Energy  

Open Energy Info (EERE)

GRR/Section 14-AK-d - Section 401 Water Quality Certification GRR/Section 14-AK-d - Section 401 Water Quality Certification < GRR Jump to: navigation, search GRR-logo.png GEOTHERMAL REGULATORY ROADMAP Roadmap Home Roadmap Help List of Sections Section 14-AK-d - Section 401 Water Quality Certification 14AKDSection401WaterQualityCertification.pdf Click to View Fullscreen Contact Agencies Alaska Department of Environmental Conservation United States Environmental Protection Agency U S Army Corps of Engineers Regulations & Policies Alaska Water Quality Standards Alaska Statutes Alaska Administrative Code Triggers None specified Click "Edit With Form" above to add content 14AKDSection401WaterQualityCertification.pdf 14AKDSection401WaterQualityCertification.pdf Error creating thumbnail: Page number not in range. Error creating thumbnail: Page number not in range.

165

GRR/Section 12-FD-f - ESA Section 7 Formal Consultation | Open Energy  

Open Energy Info (EERE)

f - ESA Section 7 Formal Consultation f - ESA Section 7 Formal Consultation < GRR Jump to: navigation, search GRR-logo.png GEOTHERMAL REGULATORY ROADMAP Roadmap Home Roadmap Help List of Sections Section 12-FD-f - ESA Section 7 Formal Consultation 12FDF - ESA Section 7 Formal Consultation.pdf Click to View Fullscreen Contact Agencies Fish and Wildlife Service Bureau of Land Management United States Forest Service Bureau of Reclamation Regulations & Policies Endangered Species Act ESA Sec. 3 ESA Sec. 7 ESA Sec. 9 ESA Sec. 10 50 CFR 17.11-17.12 50 CFR 226 50 CFR 402.02 50 CFR 402.14 Triggers None specified Click "Edit With Form" above to add content 12FDF - ESA Section 7 Formal Consultation.pdf Error creating thumbnail: Page number not in range. Error creating thumbnail: Page number not in range.

166

Energy-efficient alcohol-fuel production. Technical final report  

Science Conference Proceedings (OSTI)

The proposed utilization schedule for the alcohol fuel plant and methane generator is to produce 180 proof ethanol during the spring, summer, and fall (April to October). The ethanol will be used in the farm tractors and trucks during the planting, growing, and harvesting seasons. Some alcohol can be stored for use during the winter. The still will not be operated during the winter (November to March) when the methane from the digester will be used to replace fuel oil for heating a swine farrowing building. There are tentative plans to develop a larger methane generator, which will utilize all of the manure (dairy, beef, horses, and swine) produced on the ISU farm. If this project is completed, there will be enough methane to produce all of the alcohol fuel needed to operate all of the farm equipment, heat the buildings, and possibly generate electricity for the farm. The methane generating system developed is working so well that there is a great deal of interest in expanding the project to where it could utilize all of the livestock waste on the farm for methane production.

Not Available

1982-01-01T23:59:59.000Z

167

Particle Data Group - Hadronic Cross-sections  

NLE Websites -- All DOE Office Websites (Extended Search)

Data files and plots of cross-sections and related quantities in the 2012 Review of Particle Physics Please use this CITATION: J. Beringer et al. (Particle Data Group), Phys. Rev....

168

Section I: FUEL BILLS - Energy Information Administration  

U.S. Energy Information Administration (EIA)

Section I: FUEL BILLS I-1 In this interview you have told me how your household uses energy. ... What portion of the electric bill is for non-household uses?

169

GRR/Sections | Open Energy Information  

Open Energy Info (EERE)

GRR/Sections GRR/Sections < GRR Jump to: navigation, search GRR-logo.png GEOTHERMAL REGULATORY ROADMAP Roadmap Home Roadmap Help List of Sections Roadmap Coverage The roadmapping initiative covers the states show in green on the map below, including California, Nevada, Hawai'i, Alaska, Idaho, Utah, Oregon, and Montana. The roadmap is being developed at the federal and state levels, allowing for future expansion to the local (county) level. Development of the roadmap for two additional states (Colorado and Texas) is underway for Fiscal Year 2013. Click on a state to view Regulatory Roadmap information specific to that state. List of Roadmap Sections Overview Flowchart The flowcharts listed below were developed as part of the Geothermal Regulatory Roadmap project. The flowcharts cover the major requirements for

170

Path forward for dosimetry cross sections  

SciTech Connect

In the 1980's the dosimetry community embraced the need for a high fidelity quantification of uncertainty in nuclear data used for dosimetry applications. This led to the adoption of energy-dependent covariance matrices as the accepted manner of quantifying the uncertainty data. The trend for the dosimetry community to require high fidelity treatment of uncertainty estimates has continued to the current time where requirements on nuclear data are codified in standards such as ASTM E 1018. This paper surveys the current state of the dosimetry cross sections and investigates the quality of the current dosimetry cross section evaluations by examining calculated-to-experimental ratios in neutron benchmark fields. In recent years more nuclear-related technical areas are placing an emphasis on uncertainty quantification. With the availability of model-based cross sections and covariance matrices produced by nuclear data codes, some nuclear-related communities are considering the role these covariance matrices should play. While funding within the dosimetry community for cross section evaluations has been very meager, other areas, such as the solar-related astrophysics community and the US Nuclear Criticality Safety Program, have been supporting research in the area of neutron cross sections. The Cross Section Evaluation Working Group (CSEWG) is responsible for the creation and maintenance of the ENDF/B library which has been the mainstay for the reactor dosimetry community. Given the new trends in cross section evaluations, this paper explores the path forward for the US nuclear reactor dosimetry community and its use of the ENDF/B cross-sections. The major concern is maintenance of the sufficiency and accuracy of the uncertainty estimate when used for dosimetry applications. The two major areas of deficiency in the proposed ENDF/B approach are: 1) the use of unrelated covariance matrices in ENDF/B evaluations and 2) the lack of 'due consideration' of experimental data in the evaluation. (authors)

Griffin, P.J. [Sandia National Laboratories, Albuquerque, NM 87185-1146 (United States); Peters, C.D. [Sandia Staffing Alliance, Albuquerque, NM 87110 (United States)

2011-07-01T23:59:59.000Z

171

Electrolytic method to make alkali alcoholates using ion conducting alkali electrolyte/separator  

DOE Patents (OSTI)

Alkali alcoholates, also called alkali alkoxides, are produced from alkali metal salt solutions and alcohol using a three-compartment electrolytic cell. The electrolytic cell includes an anolyte compartment configured with an anode, a buffer compartment, and a catholyte compartment configured with a cathode. An alkali ion conducting solid electrolyte configured to selectively transport alkali ions is positioned between the anolyte compartment and the buffer compartment. An alkali ion permeable separator is positioned between the buffer compartment and the catholyte compartment. The catholyte solution may include an alkali alcoholate and alcohol. The anolyte solution may include at least one alkali salt. The buffer compartment solution may include a soluble alkali salt and an alkali alcoholate in alcohol.

Joshi, Ashok V. (Salt Lake City, UT); Balagopal, Shekar (Sandy, UT); Pendelton, Justin (Salt Lake City, UT)

2011-12-13T23:59:59.000Z

172

GRR/Section 14-CO-d - Section 401 Water Quality Certification | Open Energy  

Open Energy Info (EERE)

4-CO-d - Section 401 Water Quality Certification 4-CO-d - Section 401 Water Quality Certification < GRR Jump to: navigation, search GRR-logo.png GEOTHERMAL REGULATORY ROADMAP Roadmap Home Roadmap Help List of Sections Section 14-CO-d - Section 401 Water Quality Certification 14CODSection401WaterQualityCertification.pdf Click to View Fullscreen Contact Agencies Colorado Department of Public Health and Environment Regulations & Policies 5 CCR 1002-82 Colorado Water Quality Control Act Triggers None specified Click "Edit With Form" above to add content 14CODSection401WaterQualityCertification.pdf Error creating thumbnail: Page number not in range. Error creating thumbnail: Page number not in range. Error creating thumbnail: Page number not in range. Flowchart Narrative Section 401 of the Clean Water Act (CWA) requires a Water Quality

173

GRR/Section 14-TX-d - Section 401 Water Quality Certification | Open Energy  

Open Energy Info (EERE)

4-TX-d - Section 401 Water Quality Certification 4-TX-d - Section 401 Water Quality Certification < GRR Jump to: navigation, search GRR-logo.png GEOTHERMAL REGULATORY ROADMAP Roadmap Home Roadmap Help List of Sections Section 14-TX-d - Section 401 Water Quality Certification 14TXDSection401WaterQualityCertification (2).pdf Click to View Fullscreen Contact Agencies Railroad Commission of Texas Regulations & Policies 16 TAC 3.93 - RRC Water Quality Certification 16 TAC 3.30 - MOU between the RRC and the TCEQ Triggers None specified Click "Edit With Form" above to add content 14TXDSection401WaterQualityCertification (2).pdf Error creating thumbnail: Page number not in range. Error creating thumbnail: Page number not in range. Error creating thumbnail: Page number not in range. Flowchart Narrative Section 401 of the Clean Water Act (CWA) requires a Water Quality

174

Ligand Rearrangement Reactions of Cr(CO)6 in Alcohol Solutions:Experiment and Theory  

SciTech Connect

The ligand rearrangement reaction of Cr(CO)6 is studied in a series of alcohol solutions using ultrafast, infrared spectroscopy and Brownian dynamics simulations.

Shanoski, Jennifer E.; Glascoe, Elizabeth A.; Harris, Charles B.

2005-09-24T23:59:59.000Z

175

BSA 99-05: Anodes to Oxidize Alcohol in Fuel Cells  

BSA 99-05: Anodes to Oxidize Alcohol in Fuel Cells. BNL Reference Number: BSA 99-05. Summary. ... Brookhaven National Laboratory conducts research in ...

176

Biomass-based alcohol fuels: the near-term potential for use with gasoline  

DOE Green Energy (OSTI)

This report serves as an introduction to the requirements and prospects for a nationwide alcohol-gasoline fuel system based on alcohols derived from biomass resources. Technological and economic factors of the production and use of biomass-based methanol and ethanol fuels are evaluated relative to achieving 5 or 10 percent alcohol-gasoline blends by 1990. It is concluded the maximum attainable is a nationwide 5 percent methanol or ethanol-gasoline system replacing gasoline by 1990. Relative to existing gasoline systems, costs of alcohol-gasoline systems will be substantial.

Park, W.; Price, G.; Salo, D.

1978-08-01T23:59:59.000Z

177

REVIEW ARTICLE Alcohol and injury in Poland: review and training recommendations  

E-Print Network (OSTI)

Background Alcohol plays a significant role in accidents, injuries, and their outcomes. According to the World Health Organization (WHO), there are 76.3 million people with alcohol use disorders worldwide; in 2000, 1.8 million deaths and loss of 58.3 million disability-adjusted life years were attributed to alcohol. Methods Although the association between alcohol consumption and trauma-related morbidity and mortality is well-documented, particularly in the US, there is much less At the time this paper was written, Dr. Wozniak was a Fogarty

Piotr Wozniak; Rebecca Cunningham; Sonia Kamat; Kristen L. Barry; Frederic C. Blow; Andrzej S. Zawadzki; P. Wozniak; R. Cunningham; S. Kamat; A. S. Zawadzki; R. Cunningham

2009-01-01T23:59:59.000Z

178

Catalytic conversion of C3+ alcohols to hydrocarbon blend-stock  

Catalytic conversion of C3+ alcohols to hydrocarbon blend-stock Note: The technology described above is an early stage opportunity. Licensing rights to this ...

179

Alcohol and Marijuana Use Across the Transition to Marriage: Group Differences and Psychosocial Factors.  

E-Print Network (OSTI)

??It has been well-established that alcohol and marijuana use levels tend to decline during the transition to marriage, or the transition from single to married (more)

Auerbach, Karen

2008-01-01T23:59:59.000Z

180

Category:Regulatory Roadmap Federal Sections | Open Energy Information  

Open Energy Info (EERE)

Category Category Edit History Facebook icon Twitter icon » Category:Regulatory Roadmap Federal Sections Jump to: navigation, search GRR-logo.png Looking for the Geothermal Regulatory Roadmap? Click here for a user-friendly list of Geothermal Regulatory Roadmap pages. This is the Regulatory Roadmap Federal Sections category. Add.png Add an Section Pages in category "Regulatory Roadmap Federal Sections" The following 48 pages are in this category, out of 48 total. G GRR/Section 1-FD-a - Land Use Planning Process GRR/Section 1-FD-b - Land Use Plan Amendment Process GRR/Section 11-FD-a - NHPA Section 106 - Resource Survey GRR/Section 11-FD-b - Tribal Consultation GRR/Section 11-FD-c - NHPA Section 106 - Effects Assessment GRR/Section 11-FD-d - NHPA Section 106 - Consultation

Note: This page contains sample records for the topic "alcohol msds section" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


181

Property:GRR/SectionNumber | Open Energy Information  

Open Energy Info (EERE)

SectionNumber SectionNumber Jump to: navigation, search Property Name GRR/SectionNumber Property Type Number Description The section number of a section in the Geothermal Regulatory Roadmap. The value of this property is derived automatically by the section template and is used in sorting sections on the GRR Home page. Subproperties This property has the following 2 subproperties: G GRR/Section 6-HI-d - Oversize and/or Overweight Vehicles and Loads Permit GRR/Section 7 - Power Plant Siting/Construction Overview Pages using the property "GRR/SectionNumber" Showing 25 pages using this property. (previous 25) (next 25) G GRR/Section 1 - Land Use Overview + 1 + GRR/Section 1-AK-a - Land Use Considerations + 1 + GRR/Section 1-CA-a - State Land Use Planning + 1 +

182

Category:Regulatory Roadmap Overview Sections | Open Energy Information  

Open Energy Info (EERE)

Sections Sections Jump to: navigation, search GRR-logo.png Looking for the Geothermal Regulatory Roadmap? Click here for a user-friendly list of Geothermal Regulatory Roadmap pages. This is the Regulatory Roadmap Overview Sections category. Add.png Add an Section Pages in category "Regulatory Roadmap Overview Sections" The following 22 pages are in this category, out of 22 total. G GRR/Section 1 - Land Use Overview GRR/Section 10 - On-Site Evaluation Process GRR/Section 11 - Cultural Resource Assessment GRR/Section 12 - Flora & Fauna Resource Assessment Process GRR/Section 13 - Land Use Assessment Process GRR/Section 14 - Water Resource Assessment GRR/Section 15 - Air Quality Assessment Process GRR/Section 16 - Geological Resources Assessment Process G cont.

183

Category:Regulatory Roadmap State Sections | Open Energy Information  

Open Energy Info (EERE)

Regulatory Roadmap State Sections Regulatory Roadmap State Sections Jump to: navigation, search GRR-logo.png Looking for the Geothermal Regulatory Roadmap? Click here for a user-friendly list of Geothermal Regulatory Roadmap pages. This is the Regulatory Roadmap State Sections category. Add.png Add an Section Pages in category "Regulatory Roadmap State Sections" The following 200 pages are in this category, out of 339 total. (previous 200) (next 200) G GRR/Section 1-AK-a - Land Use Considerations GRR/Section 1-CA-a - State Land Use Planning GRR/Section 1-HI-a - Land Use Considerations GRR/Section 1-ID-a - Land Use Considerations GRR/Section 1-MT-a - Land Use Considerations GRR/Section 1-NV-a - State Land Use Planning GRR/Section 1-OR-a - Land Use Considerations GRR/Section 11-AK-a - State Cultural Considerations

184

Electron and hydrogen atom transfer mechanisms for the photoreduction of o-quinones. Visible light induced photoreactions of. beta. -lapachone with amines, alcohols, and amino alcohols  

DOE Green Energy (OSTI)

{beta}-Lapachone (1), a substituted o-naphthoquinone absorbing into the visible ({lambda}{sub max} = 424 nm in benzene), is cleanly and efficiently reduced to the corresponding semiquinone radical upon photolysis in degassed solutions with alcohols, amines, and {beta}-amino alcohols. The course and products of these photoreactions have been followed by NMR, ESR, fluorescence, and absorption spectroscopy. For all three types of reductant the overall reaction involves 2e{sup {minus}} oxidation of the donor, and the quantum efficiencies show a dependence upon quinone concentration indicative of the role of a second dark reduction of 1 by products of the primary photolysis. For amines and amino alcohols the reaction is initiated by single electron transfer quenching of triplet 1. For triethylamine the mechanism is indicated to be a sequence of two electron transfer-proton transfer steps culminating in two semiquinone radicals and the enamine Et{sub 2}NCH{double bond}CH{sub 2}. For amino alcohols a C-C cleavage concurrent with deprotonation of the alcohol (oxidative photofragmentation) occurs, in competition with reverse electron transfer, following the quenching step. For both amines and amino alcohols, limiting efficiencies of reaction approach 2 (for QH{sup {sm bullet}} formation). In contrast, both 2-propanol and benzyl alcohol are oxidized by excited states of 1 with much lower efficiency. The probable mechanism for photooxidation of the alcohols involves a H atom abstraction quenching of the excited state followed by an electron transfer-proton transfer sequence in which a ground-state 1 is reduced. Lower limiting efficiencies for photoreduction of 1 by the alcohols are attributed to inefficiencies of net H-atom transfer in the quenching step. 54 refs., 3 figs., 9 tabs.

Xiaohong Ci; Whitten, D.G. (Univ. of Rochester, NY (USA)); Silveira da Silva, R.; Nicodem, D. (Universidade Federal do Rio de Janeiro (Brazil))

1989-02-15T23:59:59.000Z

185

Sectional Model Flume Facilities | Open Energy Information  

Open Energy Info (EERE)

Sectional Model Flume Facilities Sectional Model Flume Facilities Jump to: navigation, search Basic Specifications Facility Name Sectional Model Flume Facilities Overseeing Organization United States Army Corp of Engineers (ERDC) Hydrodynamic Testing Facility Type Flume Length(m) 21.3 Beam(m) 1.4 Depth(m) 2.4 Water Type Freshwater Cost(per day) Contact POC Towing Capabilities Towing Capabilities None Wavemaking Capabilities Wavemaking Capabilities Yes Maximum Wave Height(m) 0.0 Wave Period Range(s) 0.0 Current Velocity Range(m/s) 0.0 Programmable Wavemaking No Simulated Beach No Channel/Tunnel/Flume Channel/Tunnel/Flume Yes Recirculating No Wind Capabilities Wind Capabilities None Control and Data Acquisition Description Automated data acquisition and control system Cameras None Available Sensors Flow, Pressure Range(psi), Turbulence, Velocity, Wave Probe

186

Section 999 Program Library | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Science & Innovation » Oil & Gas » Offshore Drilling » Section Science & Innovation » Oil & Gas » Offshore Drilling » Section 999 Program Library Section 999 Program Library Cost-Shared Program Publications October 2, 2013 URTAC Meeting - October 2013 October 2, 2013 UDAC Meeting - October 2013 September 10, 2013 Draft 2014 Annual Plan More Ultra-Deepwater Advisory Committee (UDAC) Activities and Products November 27, 2013 UDAC Meeting - December 2013 November 20, 2013 UDAC Meeting - December 2013 November 18, 2013 UDAC Meeting - September 2013 More Unconventional Resources Technology Advisory Committee (URTAC) Activities and Products November 27, 2013 URTAC Meeting - December 2013 November 18, 2013 URTAC Meeting - December 2013 November 18, 2013 URTAC Meeting - December 2013 More Stay Connected Fossil Energy on Facebook Fossil Energy on Twitter Sign up for NewsAlerts Fossil Energy RSS Feeds

187

Utah Antiquities Section | Open Energy Information  

Open Energy Info (EERE)

Antiquities Section Antiquities Section Jump to: navigation, search Name Utah Antiquities Section Address 300 S. Rio Grande Street Place Salt Lake City, Utah Zip 84101 Coordinates 40.7623958°, -111.9047846° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":40.7623958,"lon":-111.9047846,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

188

Top differential cross section measurements (Tevatron)  

SciTech Connect

Differential cross sections in the top quark sector measured at the Fermilab Tevatron collider are presented. CDF used 2.7 fb{sup -1} of data and measured the differential cross section as a function of the invariant mass of the t{bar t} system. The measurement shows good agreement with the standard model and furthermore is used to derive limits on the ratio {kappa}/M{sub Pl} for gravitons which decay to top quarks in the Randall-Sundrum model. D0 used 1.0 fb{sup -1} of data to measure the differential cross section as a function of the transverse momentum of the top-quark. The measurement shows a good agreement to the next-to-leading order perturbative QCD prediction and various other standard model predictions.

Jung, Andreas W.

2012-01-01T23:59:59.000Z

189

Photodisintegration Cross Section of {sup 241}Am  

Science Conference Proceedings (OSTI)

The photodisintegration cross section of radioactive {sup 241}Am has been obtained for the first time using monoenergetic {gamma}-ray beams from the HI{gamma}S facility. The induced activity of {sup 240}Am produced via the {sup 241}Am({gamma},n) reaction in the {gamma}-ray energy range from 9.5 to 16 MeV was measured by the activation technique utilizing high resolution HPGe detectors. The {sup 241}Am({gamma},n) cross section was determined both by measuring the absolute {gamma}-ray flux and by comparison to the {sup 197}Au({gamma},n) and {sup 58}Ni({gamma},n) cross section standards. The experimental data for the {sup 241}Am({gamma},n) reaction in the giant dipole resonance energy region is compared with statistical nuclear-model calculations.

Tonchev, A. P.; Howell, C. R.; Hutcheson, A.; Kwan, E.; Rusev, G.; Tornow, W. [Duke University and TUNL, Durham NC 27708 (United States); Hammond, S.; Karwowski, H. J. [University of North Carolina at Chapel Hill and TUNL, Chapel Hill NC 27599 (United States); Huibregtse, C.; Kelley, J. H. [North Carolina State University and TUNL, Raleigh NC 27695 (United States); Vieira, D. J.; Wilhelmy, J. B. [Los Alamos National Laboratory, Los Alamos NM 87545 (United States)

2009-03-10T23:59:59.000Z

190

LLNL Section I Clauses/Prescriptions  

National Nuclear Security Administration (NNSA)

AC52-06NA27344 LLNL AC52-06NA27344 LLNL Section I, Page 56 Part II - Contract Clauses Section I I-1 CONTRACT CLAUSES Unless conditionally "Noted", all contract clauses are hereby incorporated by full text. The references cited herein are from the Federal Acquisition Regulation (FAR) (48 CFR Chapter 1) and the Department of Energy Acquisition Regulation (DEAR) (48 CFR Chapter 9). Note: The titles and page locations of the clauses are as follows: CLAUSE TITLE PAGE I001 FAR 52.202-1 DEFINITIONS (JUL 2004) (DEVIATION) ..............................62 I002 FAR 52.203-3 GRATUTIES (APR 1984) ..........................................................63

191

Optimum catalytic process for alcohol fuels from syngas  

DOE Green Energy (OSTI)

The objectives of this contract are to discover and evaluate the catalytic properties of novel homogeneous, heterogeneous, or combination catalytic systems for the production of alcohol fuel extenders from syngas, to evaluate analytically and on the bench scale novel reactor concepts for use in converting syngas to liquid fuel products, and to develop on the bench scale the best combination of chemistry, reactor, and total process configuration to achieve the minimum product cost for conversion of syngas to liquid fuel products. Methanol production and heterogeneous catalysis utilizing transition elements supported on metal oxides with spinel structure are discussed. 12 figs., 16 tabs.

Not Available

1990-04-28T23:59:59.000Z

192

Novel reactor configuration for synthesis gas conversion to alcohols  

SciTech Connect

Research continued on the conversion of synthesis gas to alcohols and reactor configuration. Objectives for this quarter: the project stated on October 1, 1989 and according to the Task Schedule provided in the original work breakdown schedule, Task I was to be completed in the first quarter and Task II to be started. Task I consisted of construction of the slurry reactor set-up to be used in Task IV for determination of the reactor kinetics and procurement of the parts for automation equipment, separators, computer activated parts etc. for automation of the trickle bed rector and GC equipment. Task II consisted of standardization and automation of GC analysis protocols. 1 fig.

Akgerman, A.; Anthony, R.G. (Texas A and M Univ., College Station, TX (USA). Dept. of Chemical Engineering)

1989-01-01T23:59:59.000Z

193

Role of osteopontin in hepatic neutrophil infiltration during alcoholic steatohepatitis  

SciTech Connect

Alcoholic liver disease (ALD) is a major complication of heavy alcohol (EtOH) drinking and is characterized by three progressive stages of pathology: steatosis, steatohepatitis, and fibrosis/cirrhosis. Alcoholic steatosis (AS) is the initial stage of ALD and consists of fat accumulation in the liver accompanied by minimal liver injury. AS is known to render the hepatocytes increasingly sensitive to toxicants such as bacterial endotoxin (LPS). Alcoholic steatohepatitis (ASH), the second and rate-limiting step in the progression of ALD, is characterized by hepatic fat accumulation, neutrophil infiltration, and neutrophil-mediated parenchymal injury. However, the pathogenesis of ASH is poorly defined. It has been theorized that the pathogenesis of ASH involves interaction of increased circulating levels of LPS with hepatocytes being rendered highly sensitive to LPS due to heavy EtOH consumption. We hypothesize that osteopontin (OPN), a matricellular protein (MCP), plays an important role in the hepatic neutrophil recruitment due to its enhanced expression during the early phase of ALD (AS and ASH). To study the role of OPN in the pathogenesis of ASH, we induced AS in male Sprague-Dawley rats by feeding EtOH-containing Lieber-DeCarli liquid diet for 6 weeks. AS rats experienced extensive fat accumulation and minimal liver injury. Moderate induction in OPN was observed in AS group. ASH was induced by feeding male Sprague-Dawley rats EtOH-containing Lieber-DeCarli liquid diet for 6 weeks followed by LPS injection. The ASH rats had substantial neutrophil infiltration, coagulative oncotic necrosis, and developed higher liver injury. Significant increases in the hepatic and circulating levels of OPN was observed in the ASH rats. Higher levels of the active, thrombin-cleaved form of OPN in the liver in ASH group correlated remarkably with hepatic neutrophil infiltration. Finally, correlative studies between OPN and hepatic neutrophil infiltration was corroborated in a simple rat peritoneal model where enhanced peritoneal fluid neutrophil infiltration was noted in rats injected OPN intraperitoneally. Taken together these data indicate that OPN expression induced during ASH may play a significant role in the pathogenesis of ASH by stimulating neutrophil transmigration.

Apte, Udayan M. [Department of Pathobiology, College of Veterinary Medicine, Texas A and M University, MS4467, College Station, TX 77843-4467 (United States); Banerjee, Atrayee [Department of Pathobiology, College of Veterinary Medicine, Texas A and M University, MS4467, College Station, TX 77843-4467 (United States); McRee, Rachel [Department of Pathobiology, College of Veterinary Medicine, Texas A and M University, MS4467, College Station, TX 77843-4467 (United States); Wellberg, Elizabeth [Department of Pathobiology, College of Veterinary Medicine, Texas A and M University, MS4467, College Station, TX 77843-4467 (United States); Ramaiah, Shashi K. [Department of Pathobiology, College of Veterinary Medicine, Texas A and M University, MS4467, College Station, TX 77843-4467 (United States)]. E-mail: sramaiah@cvm.tamu.edu

2005-08-22T23:59:59.000Z

194

Level of osteopenia and bone recovery in alcohol-fed adolescent rats  

E-Print Network (OSTI)

Adolescence is a period in human growth and development that is a time of rapid and drastic change. It is also known to be an age of widespread alcohol abuse. Studies addressing the reversibility of the deleterious effects of chronic alcohol consumption on young, actively growing adolescent bones have not been done. The objective of this study was to determine the level of bone recovery, if any, once an adolescent ceases alcohol consumption. Fifty, 4-week old, female, Sprague-Dawley rats were individually housed and maintained in an American Association for the Accreditation of Laboratory Animal Care-accredited facility at Texas A&M. The rats (n = 6 or 7 per group) were fed either alcohol (35% ethanol-derived calories), isocaloric liquid diet, or chow for 2 or 4 weeks, depending on the experimental group. The weekly blood alcohol concentrations averaged 309 [] 9 mg/dl. The rats were sacrificed 2 and 4 weeks after the experimental feeding began. The BioQuant Morphometric System was used to perform the histomorphometric analyses of the proximal tibia. Tibia bone volume per trabecular volume (BV/TV) in both age groups of alcohol and pair-fed animals was significantly less when compared to the chow 4 week animals. BV/TV was increased in the alcohol recovery group when compared to the alcohol 2 and 4 week groups, but the level of growth never reached the chow-fed 4 week group. Femur length, diameter and volume measurements increased in the alcohol recovery group when compared to both the alcohol 2 and 4 week groups. However, the length and volume parameters did not fully recover to equal those of the control chow 4 week animals, or even the some-age pair-fed animals. Femur diameter of the alcohol recovery animals was comparable to the alcohol 4 week animals, but less than the chow-fed. Alcohol also suppressed IGF-I levels. Full bone recovery did not occur within two weeks after removal of alcohol from the diet, suggesting the detrimental effects due to alcohol were not completely reversible during this time frame.

Spears, Heather Lynae

1999-01-01T23:59:59.000Z

195

Economics of producing fuel-grade alcohol from corn in western Ohio  

Science Conference Proceedings (OSTI)

The production of significant quantities of alcohol fuel will have important effects on the use of agricultural resources, including increased food prices. The two major objectives of this research were to determine (1) the potential effects of alcohol-fuel production on agriculture, and (2) the increase in energy prices needed for alcohol-fuel production to become economic. Western Ohio (the Corn Belt part of the state) was chosen for study. A quadratic-programming model with crop, livestock, and alcohol-fuel-production activities was used for analysis. Four alcohol-fuel-production levels were analyzed: 100, 200, 300 and 400 million gallons. The 400-million-gallon level represents western Ohio's share of alcohol-fuel production for a national gasohol program. The production of alcohol results in a high protein by-product feed that can substitute for soybean meal. Efficient use of this by-product is a crucial factor affecting resource use and food prices. At low alcohol-fuel production levels, 80% of the additional cropland required for increased corn production comes from the cropland released through by-product feeding. However, as alcohol-fuel production increases, livestock's ability to use efficiently this by-product feed decreases. This in turn, reduces greatly the cropland that can be released for increased corn production. Consequently, food prices increase substantially. The quantity of land released through by-product feeding, at high alcohol-fuel-production levels, can be increased if the corn is first wet milled. Wet milling produces high-protein feeds that can be used more efficiently by livestock. For alcohol-fuel production to become economic, crude oil prices must increase by ten cents per gallon for the wet-milling process and 22 cents per gallon for the conventional distillery process (1981 $).

Ott, S.L.

1981-01-01T23:59:59.000Z

196

Chapter 7, section 6-8 Chapter 8, section 1-5  

E-Print Network (OSTI)

1 Week 7, Chapter 7, section 6-8 Chapter 8, section 1-5 Potential Energy and Energy Conservation Potential Energy Potential energy is energy related to the configuration of a system in which with only specific types of forces acting between members of a system Gravitational Potential Energy

197

Solar fusion cross sections Eric G. Adelberger  

E-Print Network (OSTI)

Solar fusion cross sections Eric G. Adelberger Nuclear Physics Laboratory, University of Washington of Washington, Seattle, Washington 98195 Stuart J. Freedman Department of Physics, University of California, Berkeley, California 94720 Moshe Gai Department of Physics U46, University of Connecticut, Storrs

Bahcall, John

198

Testing (Validating?) Cross Sections with ICSBEP Benchmarks  

SciTech Connect

We discuss how to use critical benchmarks from the International Handbook of Evaluated Criticality Safety Benchmark Experiments to determine the applicability of specific cross sections to the end-user's problem of interest. Particular attention is paid to making sure the selected suite of benchmarks includes the user's range of applicability (ROA).

Kahler, Albert C. III [Los Alamos National Laboratory

2012-06-28T23:59:59.000Z

199

Student Response Sheet Name: _________________ Section One. Introduction  

E-Print Network (OSTI)

" in which category? Section 2. Coal Mine Locations 1. Pennsylvanian-age rocks are located in which general this layer? 4. If a company wanted to mine the Danville coal deposits along the western border of Indiana desiring to mine Springfield coal deposits along the western border of Indiana use surface or underground

Polly, David

200

Maximizing Buoyancy Flux across Layered Geostrophic Sections  

Science Conference Proceedings (OSTI)

For layered analogues of the ocean stratification, the problem of maximizing buoyancy flux across a section with zero mass flux is considered. The two layer situation on an f-plane is particularly simple and it is shown that the buoyancy flux is ...

Nelson G. Hogg; Henry M. Stommel

1990-02-01T23:59:59.000Z

Note: This page contains sample records for the topic "alcohol msds section" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


201

GRR/Section 12-FD-e -ESA Section 7 Informal Consultation | Open Energy  

Open Energy Info (EERE)

e -ESA Section 7 Informal Consultation e -ESA Section 7 Informal Consultation < GRR Jump to: navigation, search GRR-logo.png GEOTHERMAL REGULATORY ROADMAP Roadmap Home Roadmap Help List of Sections Section 12-FD-e -ESA Section 7 Informal Consultation 12FDE - ESASection7InformalConsultation.pdf Click to View Fullscreen Contact Agencies Fish and Wildlife Service Bureau of Land Management United States Forest Service Bureau of Reclamation Regulations & Policies Endangered Species Act 50 CFR 17.11-17.12 50 CFR 402.02 50 CFR 402.13 50 CFR 402.14 Triggers None specified Click "Edit With Form" above to add content 12FDE - ESASection7InformalConsultation.pdf Error creating thumbnail: Page number not in range. Error creating thumbnail: Page number not in range. Error creating thumbnail: Page number not in range.

202

GRR/Section 12-FD-d - ESA Section 10 Take Permit | Open Energy Information  

Open Energy Info (EERE)

Page Page Edit with form History Facebook icon Twitter icon » GRR/Section 12-FD-d - ESA Section 10 Take Permit < GRR Jump to: navigation, search GRR-logo.png GEOTHERMAL REGULATORY ROADMAP Roadmap Home Roadmap Help List of Sections Section 12-FD-d - ESA Section 10 Take Permit 12FDDESASection10TakePermit.pdf Click to View Fullscreen Contact Agencies Fish and Wildlife Service National Marine Fisheries Service Regulations & Policies Endangered Species Act National Environmental Policy Act Triggers None specified Click "Edit With Form" above to add content 12FDDESASection10TakePermit.pdf Error creating thumbnail: Page number not in range. Error creating thumbnail: Page number not in range. Error creating thumbnail: Page number not in range. Flowchart Narrative

203

GRR/Section 11-FD-c - NHPA Section 106 - Effects Assessment | Open Energy  

Open Energy Info (EERE)

FD-c - NHPA Section 106 - Effects Assessment FD-c - NHPA Section 106 - Effects Assessment < GRR Jump to: navigation, search GRR-logo.png GEOTHERMAL REGULATORY ROADMAP Roadmap Home Roadmap Help List of Sections Section 11-FD-c - NHPA Section 106 - Effects Assessment 11FDCNHPASection106EffectsAssessment.pdf Click to View Fullscreen Contact Agencies Advisory Council on Historic Preservation Regulations & Policies National Historic Preservation Act 36 CFR 800 - Protection of Historic Properties Triggers None specified Click "Edit With Form" above to add content 11FDCNHPASection106EffectsAssessment.pdf Error creating thumbnail: Page number not in range. Error creating thumbnail: Page number not in range. Error creating thumbnail: Page number not in range. Flowchart Narrative The Federal agency must proceed to the assessment of adverse effects when

204

GRR/Section 11-FD-d - NHPA Section 106 - Consultation | Open Energy  

Open Energy Info (EERE)

form form View source History View New Pages Recent Changes All Special Pages Semantic Search/Querying Get Involved Help Apps Datasets Community Login | Sign Up Search Page Edit with form History Facebook icon Twitter icon » GRR/Section 11-FD-d - NHPA Section 106 - Consultation < GRR Jump to: navigation, search GRR-logo.png GEOTHERMAL REGULATORY ROADMAP Roadmap Home Roadmap Help List of Sections Section 11-FD-d - NHPA Section 106 - Consultation 11FDDNHPASection106Consultation.pdf Click to View Fullscreen Contact Agencies Advisory Council on Historic Preservation Regulations & Policies National Historic Preservation Act 36 CFR 800 - Protection of Historic Properties Triggers None specified Click "Edit With Form" above to add content 11FDDNHPASection106Consultation.pdf

205

Automatic registration of serial mammary gland sections  

SciTech Connect

We present two new methods for automatic registration of microscope images of consecutive tissue sections. They represent two possibilities for the first step in the 3-D reconstruction of histological structures from serially sectioned tissue blocks. The goal is to accurately align the sections in order to place every relevant shape contained in each image in front of its corresponding shape in the following section before detecting the structures of interest and rendering them in 3D. This is accomplished by finding the best rigid body transformation (translation and rotation) of the image being registered by maximizing a matching function based on the image content correlation. The first method makes use of the entire image information, whereas the second one uses only the information located at specific sites, as determined by the segmentation of the most relevant tissue structures. To reduce computing time, we use a multiresolution pyramidal approach that reaches the best registration transformation in increasing resolution steps. In each step, a subsampled version of the images is used. Both methods rely on a binary image which is a thresholded version of the Sobel gradients of the image (first method) or a set of boundaries manually or automatically obtained that define important histological structures of the sections. Then distance-transform of the binary image is computed. A proximity function is then calculated between the distance image of the image being registered and that of the reference image. The transformation providing a maximum of the proximity function is then used as the starting point of the following step. This is iterated until the registration error lies below a minimum value.

Arganda-Carreras, Ignacio; Fernandez-Gonzalez, Rodrigo; Ortiz-de-Solorzano, Carlos

2004-04-13T23:59:59.000Z

206

Notice of Availability of Section 3116 Determination for Salt...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Notice of Availability of Section 3116 Determination for Salt Waste Disposal at the Savannah River Site Notice of Availability of Section 3116 Determination for Salt Waste Disposal...

207

Influence of alcohol on reliability and safety driver during driving on vehicle simulators  

Science Conference Proceedings (OSTI)

Alcohol, drugs and consequent serious attention decrease and aggression of human operators is one of the most common causes of accidents in traffic. Measure this situations are very dangerous and in real traffic. The paper describes objective methods ... Keywords: alcohol, measure, vehicle simulator, virtual reality

Roman Pieknik

2009-11-01T23:59:59.000Z

208

Objective methods of assessment of influence of alcohol on driving safety: study performed driving simulators  

Science Conference Proceedings (OSTI)

The paper is focused on an introduction of a set of experiments focused on objective methods used for detection of driving impairment caused by influence of different level of alcohol in blood. It introduces the initial experiments which were performed ... Keywords: alcohol, driver's impairment, driving simulation

Roman Pieknk; Stanislav Novotny; Petr Bouchner

2007-09-01T23:59:59.000Z

209

Addendum: Tenth International Symposium on Alcohol Fuels, The road to commercialization  

DOE Green Energy (OSTI)

The Tenth International Symposium on ALCOHOL FUELS ``THE ROAD TO COMMERCIALIZATION`` was held at the Broadmoor Hotel, Colorado Springs, Colorado, USA November 7--10, 1993. Twenty-seven papers on the production of alcohol fuels, specifications, their use in automobiles, buses and trucks, emission control, and government policies were presented. Individual papers have been processed separately for entry into the data base.

Not Available

1994-05-01T23:59:59.000Z

210

PROMOTED ZINC CHROMITE CATALYSTS FOR HIGHER ALCOHOL SYNTHESIS  

SciTech Connect

During this reporting period, a ''zinc chromite'' catalyst promoted with 6 wt.% cesium (Cs) was evaluated at the following operating conditions: Temperature - 375 C and 400 C; Total Pressure--13.6 MPa (2000 psig); Gas Hourly Space Velocity (GHSV) - 5000 standard liters/kg(cat)-hr; and H{sub 2}/CO feed ratio--0.5, 1.0 and 2.0 mole/mole. Decahydronaphthalene (DHN) was used as the slurry liquid. The experiment lasted for twelve days of continuous operation. Unpromoted zinc chromite catalyst then was re-examined under the same operating conditions. Reproducible data was achieved with a continuous liquid make-up. Compared with unpromoted zinc chromite catalyst, 6 wt.% Cs-promoted catalyst shifted the product distribution from methanol to higher alcohols, even though methanol was still the major product. The effect of operating conditions was less important than the addition of promoter. However, it was observed that higher temperature favors higher alcohol synthesis, and that a higher H{sub 2}/CO ratio leads to lower oxygenates selectivity and higher hydrocarbons selectivity. These trends showed clearly with the Cs-promoted catalyst, but were not as prominent with the unpromoted catalyst. The slurry liquid did not decompose or alkylate to a measurable extent during either continuous, 12 - day experiment, even with the higher reactor temperature (400 C). There was a relatively significant loss of catalyst surface area during the experiment with the promoted catalyst, but not with the unpromoted catalyst.

Ms. Xiaolei Sun; Professor George W. Roberts

2000-12-20T23:59:59.000Z

211

Mechanisms of alcohol-induced neuroteratology: an examination of the roles of fetal cerebral blood flow and hypoxia  

E-Print Network (OSTI)

Hypoxia (decreased tissue oxygen levels) has long been considered as a possible mechanism of alcohol-induced developmental deficits, yet research has not conclusively disproved this hypothesis, nor has it provided substantial evidence for a mechanism of developmental alcohol insults involving hypoxia. Previous research has shown that moderate acute doses of alcohol does not induce hypoxemia (decreased arterial oxygen levels), yet these same studies have shown that this same alcohol exposure does transiently decrease cerebral blood flow (CBF). This is significant because although developmental alcohol exposure did not result in hypoxemia, the decreases in CBF seen in these previous studies may induce hypoxia within the brain. Unfortunately, these experiments were only performed after acute doses of alcohol, so it is unknown if a more chronic or repeated alcohol exposure paradigm would have similar effects. The present study examined blood flow in the sheep fetus after repeated alcohol exposure in a bingelike paradigm throughout the third trimester. Additionally, this study examined the fetal neurovascular response to a subsequent infusion of alcohol after the repeated alcohol exposure. This latter experiment was designed to examine the hypothesis that alcohol exposure throughout the third trimester affects the normal responsiveness of the neurovasculature to alcohol (compared to previous research demonstrating acute alcohol-induced decreases in CBF). The results from the present experiments indicate that although few regions were significant, the majority of the regions (especially the brain regions) exhibited a trend for increases in blood flows after alcohol exposure. This phenomenon was especially prominent in the group receiving the lower dose of alcohol. Additionally, the data from this study demonstrated that after repeated alcohol exposures the near-term sheep fetus did not respond to a subsequent dose of alcohol in a similar manner seen in previous experiments when the acute alcohol exposure was administered in alcohol nave animals. After the final alcohol exposure the subjects in this study had either no effect in terms of blood flow or an increase in CBF. This is opposite to previous observations which demonstrated reduced blood flow in numerous brain regions. The present experiments suggest that alcohol does not induce fetal hypoxia, but does negatively affect the normal neurovascular response to alcohol. This latter phenomenon could have negative consequences on future development of the brain.

Parnell, Scott Edward

2004-12-01T23:59:59.000Z

212

Enabling Technologies for Ceramic Hot Section Components  

SciTech Connect

Silicon-based ceramics are attractive materials for use in gas turbine engine hot sections due to their high temperature mechanical and physical properties as well as lower density than metals. The advantages of utilizing ceramic hot section components include weight reduction, and improved efficiency as well as enhanced power output and lower emissions as a result of reducing or eliminating cooling. Potential gas turbine ceramic components for industrial, commercial and/or military high temperature turbine applications include combustor liners, vanes, rotors, and shrouds. These components require materials that can withstand high temperatures and pressures for long duration under steam-rich environments. For Navy applications, ceramic hot section components have the potential to increase the operation range. The amount of weight reduced by utilizing a lighter gas turbine can be used to increase fuel storage capacity while a more efficient gas turbine consumes less fuel. Both improvements enable a longer operation range for Navy ships and aircraft. Ceramic hot section components will also be beneficial to the Navy's Growth Joint Strike Fighter (JSF) and VAATE (Versatile Affordable Advanced Turbine Engines) initiatives in terms of reduced weight, cooling air savings, and capability/cost index (CCI). For DOE applications, ceramic hot section components provide an avenue to achieve low emissions while improving efficiency. Combustors made of ceramic material can withstand higher wall temperatures and require less cooling air. Ability of the ceramics to withstand high temperatures enables novel combustor designs that have reduced NO{sub x}, smoke and CO levels. In the turbine section, ceramic vanes and blades do not require sophisticated cooling schemes currently used for metal components. The saved cooling air could be used to further improve efficiency and power output. The objectives of this contract were to develop technologies critical for ceramic hot section components for gas turbine engines. Significant technical progress has been made towards maturation of the EBC and CMC technologies for incorporation into gas turbine engine hot-section. Promising EBC candidates for longer life and/or higher temperature applications relative to current state of the art BSAS-based EBCs have been identified. These next generation coating systems have been scaled-up from coupons to components and are currently being field tested in Solar Centaur 50S engine. CMC combustor liners were designed, fabricated and tested in a FT8 sector rig to demonstrate the benefits of a high temperature material system. Pretest predictions made through the use of perfectly stirred reactor models showed a 2-3x benefit in CO emissions for CMC versus metallic liners. The sector-rig test validated the pretest predictions with >2x benefit in CO at the same NOx levels at various load conditions. The CMC liners also survived several trip shut downs thereby validating the CMC design methodology. Significant technical progress has been made towards incorporation of ceramic matrix composites (CMC) and environmental barrier coatings (EBC) technologies into gas turbine engine hot-section. The second phase of the program focused on the demonstration of a reverse flow annular CMC combustor. This has included overcoming the challenges of design and fabrication of CMCs into 'complex' shapes; developing processing to apply EBCs to 'engine hardware'; testing of an advanced combustor enabled by CMCs in a PW206 rig; and the validation of performance benefits against a metal baseline. The rig test validated many of the pretest predictions with a 40-50% reduction in pattern factor compared to the baseline and reductions in NOx levels at maximum power conditions. The next steps are to develop an understanding of the life limiting mechanisms in EBC and CMC materials, developing a design system for EBC coated CMCs and durability testing in an engine environment.

Venkat Vedula; Tania Bhatia

2009-04-30T23:59:59.000Z

213

Enabling Technologies for Ceramic Hot Section Components  

DOE Green Energy (OSTI)

Silicon-based ceramics are attractive materials for use in gas turbine engine hot sections due to their high temperature mechanical and physical properties as well as lower density than metals. The advantages of utilizing ceramic hot section components include weight reduction, and improved efficiency as well as enhanced power output and lower emissions as a result of reducing or eliminating cooling. Potential gas turbine ceramic components for industrial, commercial and/or military high temperature turbine applications include combustor liners, vanes, rotors, and shrouds. These components require materials that can withstand high temperatures and pressures for long duration under steam-rich environments. For Navy applications, ceramic hot section components have the potential to increase the operation range. The amount of weight reduced by utilizing a lighter gas turbine can be used to increase fuel storage capacity while a more efficient gas turbine consumes less fuel. Both improvements enable a longer operation range for Navy ships and aircraft. Ceramic hot section components will also be beneficial to the Navy's Growth Joint Strike Fighter (JSF) and VAATE (Versatile Affordable Advanced Turbine Engines) initiatives in terms of reduced weight, cooling air savings, and capability/cost index (CCI). For DOE applications, ceramic hot section components provide an avenue to achieve low emissions while improving efficiency. Combustors made of ceramic material can withstand higher wall temperatures and require less cooling air. Ability of the ceramics to withstand high temperatures enables novel combustor designs that have reduced NO{sub x}, smoke and CO levels. In the turbine section, ceramic vanes and blades do not require sophisticated cooling schemes currently used for metal components. The saved cooling air could be used to further improve efficiency and power output. The objectives of this contract were to develop technologies critical for ceramic hot section components for gas turbine engines. Significant technical progress has been made towards maturation of the EBC and CMC technologies for incorporation into gas turbine engine hot-section. Promising EBC candidates for longer life and/or higher temperature applications relative to current state of the art BSAS-based EBCs have been identified. These next generation coating systems have been scaled-up from coupons to components and are currently being field tested in Solar Centaur 50S engine. CMC combustor liners were designed, fabricated and tested in a FT8 sector rig to demonstrate the benefits of a high temperature material system. Pretest predictions made through the use of perfectly stirred reactor models showed a 2-3x benefit in CO emissions for CMC versus metallic liners. The sector-rig test validated the pretest predictions with >2x benefit in CO at the same NOx levels at various load conditions. The CMC liners also survived several trip shut downs thereby validating the CMC design methodology. Significant technical progress has been made towards incorporation of ceramic matrix composites (CMC) and environmental barrier coatings (EBC) technologies into gas turbine engine hot-section. The second phase of the program focused on the demonstration of a reverse flow annular CMC combustor. This has included overcoming the challenges of design and fabrication of CMCs into 'complex' shapes; developing processing to apply EBCs to 'engine hardware'; testing of an advanced combustor enabled by CMCs in a PW206 rig; and the validation of performance benefits against a metal baseline. The rig test validated many of the pretest predictions with a 40-50% reduction in pattern factor compared to the baseline and reductions in NOx levels at maximum power conditions. The next steps are to develop an understanding of the life limiting mechanisms in EBC and CMC materials, developing a design system for EBC coated CMCs and durability testing in an engine environment.

Venkat Vedula; Tania Bhatia

2009-04-30T23:59:59.000Z

214

Alcoholic fermentation of raw sweet potato by a nonconventional method using Endomycopsis fibuligera glucoamylase preparation  

Science Conference Proceedings (OSTI)

In recent years, alcoholic fermentation has received much attention as an alternative energy source. In conventional alcoholic fermentation from starchy materials, precooking is necessary for liquefaction and saccharification of the broth, which requires a large amount of heat energy - about 30-40% of all energy spent for alcohol production. Ueda and his co-workers have attempted to produce ethanol from raw starch in a single-step process, which combines liquefaction, saccharification, and yeast fermentation without cooking and autoclaving by using glucoamylase preparation from Aspergillus niger in order to save the cost of energy consumption by cooking. Ueda has also reported alcoholic fermentation of sweet potato without cooking by using Rhizopus glucoamylase preparation. In the present communication, we report the effectiveness of alcoholic fermentation of sweet potato without cooking by using Endomycopsis fibuligers glucoamylase preparation. (Refs. 5).

Saha, B.C.; Ueda, S.

1983-04-01T23:59:59.000Z

215

Diboson production cross section at LHC  

E-Print Network (OSTI)

This paper presents an overview of the diboson production cross-section measurements and constraints on anomalous triple-gauge boson couplings performed by the ATLAS and CMS collaborations using proton-proton collisions produced at a centre-of-mass energy of sqrt{s} = 7 and 8 TeV at LHC. Results for all combinations of W, Z and \\gamma\\ gauge bosons (excluding \\gamma\\gamma) are presented with emphasis on the new WZ and ZZ production cross sections measured by ATLAS at sqrt{s} = 8 TeV and on the new constraints on anomalous triple-gauge couplings set by CMS in the WW and Z\\gamma\\ modes.

Vincenzo Lombardo

2013-05-16T23:59:59.000Z

216

Electron-collision cross sections for iodine  

Science Conference Proceedings (OSTI)

We present results from a joint experimental and theoretical study of elastic electron scattering from atomic iodine. The experimental results were obtained by subtracting known cross sections from the measured data obtained with a pyrolyzed mixed beam containing a variety of atomic and molecular species. The calculations were performed using both a fully relativistic Dirac B-spline R-matrix (close-coupling) method and an optical model potential approach. Given the difficulty of the problem, the agreement between the two sets of theoretical predictions and the experimental data for the angle-differential and the angle-integrated elastic cross sections at 40 eV and 50 eV is satisfactory.

Zatsarinny, O.; Bartschat, K. [Department of Physics and Astronomy, Drake University, Des Moines, Iowa 50311 (United States); Garcia, G. [Instituto de Fisica Fundamental, Consejo Superior de Investigaciones Cientificas, Madrid E-28006 (Spain); Blanco, F. [Departamento de Fisica Atomica, Molecular y Nuclear, Universidad Complutense de Madrid, Madrid E-28040 (Spain); Hargreaves, L.R.; Jones, D.B.; Murrie, R.; Brunton, J.R. [ARC Centre for Antimatter-Matter Studies, School of Chemical and Physical Sciences, Flinders University, GPO Box 2100, Adelaide, SA 5001 (Australia); Brunger, M.J. [ARC Centre for Antimatter-Matter Studies, School of Chemical and Physical Sciences, Flinders University, GPO Box 2100, Adelaide, SA 5001 (Australia); Institute of Mathematical Sciences, University of Malaya, 50603, Kuala Lumpur (Malaysia); Hoshino, M. [Department of Materials and Life Sciences, Sophia University, Chiyoda ku, Tokyo 102-8554 (Japan); Buckman, S.J. [ARC Centre for Antimatter-Matter Studies, Research School of Physics and Engineering, Australian National University, Canberra, ACT 0200 (Australia)

2011-04-15T23:59:59.000Z

217

Neutron cross section measurements at WNR  

DOE Green Energy (OSTI)

The Weapons Neutron Research Facility has been used to obtain moderate-resolution total neutron cross section data for H, C, /sup 208/Pb, /sup 232/Th, /sup 238/U, and /sup 242/Pu over the energy range 5 to 200 MeV. Neutrons were produced by bombarding a 2.5-cm diam by 15-cm long Ta target with an 800 MeV pulsed proton beam from LAMPF. A 10.2-cm diam by 15.2-cm thick NE110 proton recoil detector was used at a flight path of 32 meters, giving a time-of-flight resolution of 60 ps/m. The total cross section results are compared to ENDF/BV evaluations and to previous data where possible.

Lisowski, P.W.; Archampaugh, G.F.; Moore, M.S.; Morgan, G.L.; Shamu, R.E.

1980-01-01T23:59:59.000Z

218

SSCL RFQ-DTL Matching Section instrumentation  

Science Conference Proceedings (OSTI)

A description of the SSCL RFQ-DTL Matching Section instrumentation is presented with emphasis on design issues and early instrumentation commissioning results. The H{sup {minus}} beam energy through the RFQ-DTL matching section is 2.5 MeV, the beam current is 27 mA with a pulse width of 35 Its. The typical beam diameter is 3 mm. The instrumentation consists of three beam position monitors (BPM), a wire scanner, beam loss monitors (BLM), a slit and collector emittance measurement unit (EMU), a current toroid, and a Faraday cup. The instruments were designed to accommodate high current densities, have a large dynamic range with moderate bandwidths, and fit congested spaces.

Datte, P.; Aielo, R.; Hayworth, M. [and others

1993-11-01T23:59:59.000Z

219

OpenEI Community - Section 7  

Open Energy Info (EERE)

/0 en Idaho Meeting #2 /0 en Idaho Meeting #2 http://en.openei.org/community/blog/idaho-meeting-2 The second Idaho GRR meeting was held today in Boise.  Though the intent of the meeting was to focus on identifying permitting concerns, agencies and developers alike had few concerns with the current process.  There were agency personnel in attendance who had not attended the first Idaho meeting, so the workshop was a great opportunity to work through the flowcharts relevant to those agencies.read more http://en.openei.org/community/blog/idaho-meeting-2#comments endangered species Fauna Fish and Wildlife Flora FWS Section 12 Section 7 Geothermal

220

Gas Turbine Hot Section Component Life Tracking  

Science Conference Proceedings (OSTI)

Damage tracking softwarebacked by comprehensive analysis techniquesprovides a means for owners/operators to independently track and predict life consumption for critical gas turbine hot section components. Results can be compared with equipment supplier formulated intervals. This report updates the development status of damage tracking software for managing life-cycle costs by improving owner/operator understanding of component life and life consumption as a function of turbine ...

2012-12-03T23:59:59.000Z

Note: This page contains sample records for the topic "alcohol msds section" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


221

HUMAN RESOURCES MANUAL SECTION 5: STUDENT EMPLOYEES  

E-Print Network (OSTI)

. University Work-Study Program 1. An undergraduate work-study student employee must be enrolled for at least EMPLOYEES 2 | P a g e S e c t i o n 4 University Work-Study Program (continued) 4. Hiring departments shouldHUMAN RESOURCES MANUAL SECTION 5: STUDENT EMPLOYEES 1 | P a g e S e c t i o n 4 Program

222

Major developments in section 404-permitting  

Science Conference Proceedings (OSTI)

Mountain coal mining in the Central Appalachians faces increased challenge under the Clean Water Act (CWA). These challenges have included the US Environmental Protection Agency's (EPA) increased involvement in permitting under Section 404 of the CWA; active opposition by environmental groups to Section 404 permits; and proposed federal legislation to reduce the availability of these permits. These recent challenges culminated in a June 11, 2009, Memorandum of Understanding (MoU) between the PEA, the Department of Interior (DoI) and the Army Corps of Engineers (Corps) that will limit the use of general permits for mountaintop coal mining and increase the scrutiny applied to individual permits, while also providing a coordinated approach for reviewing the backlog of pending permit application. By entering into the MoU, the federal agencies aim to reduce the environmental impacts of mountaintop coal mining while increasing certainty and transparency for permit applications. Challenges to Section 404 permitting for mountaintop coal mining are dynamic and new developments occur almost daily. This article provides a snapshot of the current climate.

Ahrens, M.; Orr, S. [Lathan & Watkins LLP (United States)

2009-06-15T23:59:59.000Z

223

Cross sections for electron scattering from magnesium  

SciTech Connect

A B-spline R-matrix (close-coupling) method has been used to perform a systematic study of angle-differential cross sections for electron scattering from neutral magnesium. The calculations cover elastic scattering and excitation of the five excited states (3s3p) {sup 3,1}P{sup o}, (3s3d) {sup 1}D, (3s4s) {sup 1}S, and (3s4p) {sup 1}P{sup o}. A multiconfiguration Hartree-Fock method with nonorthogonal orbitals was employed for an accurate representation of the target wave functions. The close-coupling expansion for the collision problem included 37 bound states of neutral magnesium. Angle-differential cross sections are presented for incident electron energies from 10 to 100 eV. These results, as well as the corresponding angle-integrated cross sections, are compared with various experimental data and predictions from other close-coupling and distorted-wave calculations. In spite of a few remaining discrepancies, the overall agreement between our results and the experimental data is very satisfactory.

Zatsarinny, Oleg; Bartschat, Klaus; Gedeon, Sergey; Gedeon, Viktor; Lazur, Vladimir; Nagy, Elizabeth [Department of Physics and Astronomy, Drake University, Des Moines, Iowa 50311 (United States); Department of Theoretical Physics, Uzhgorod State University, Uzhgorod 88000 (Ukraine)

2009-05-15T23:59:59.000Z

224

GRR/Section 14-ID-d - Section 401 Water Quality Certification...  

Open Energy Info (EERE)

GRRSection 14-ID-d - Section 401 Water Quality Certification Process < GRR Jump to: navigation, search GRR-logo.png GEOTHERMAL REGULATORY ROADMAP Roadmap Home Roadmap Help List of...

225

Electrocatalysis: A Direct Alcohol Fuel Cell and Surface Science Perspective  

Science Conference Proceedings (OSTI)

In this report, we discuss some of the advances in surface science and theory that have enabled a more detailed understanding of the mechanisms that govern the electrocatalysis. More specifically, we examine in detail the electrooxidation of C-1 and C-2 alcohol molecules in both acidic and basic media. A combination of detailed in situ spectroscopic measurements along with density functional theory calculations have helped to establish the mechanisms that control the reaction paths and the influence of acidic and alkaline media. We discuss some of the synergies and differences between electrocatalysis and aqueous phase heterogeneous catalysis. Such analyses begin to establish a common language and framework by which to compare as well as advance both fields. (C) 2012 Elsevier B.V. All rights reserved.

Braunchweig, B [University of Illinois, Urbana-Champaign; Hibbitts, David D [ORNL; Neurock, Matthew [University of Virginia; Wieckowski, A. [University of Illinois, Urbana-Champaign

2013-01-01T23:59:59.000Z

226

Electrocatalysis: A direct alcohol fuel cell and surface science perspective  

Science Conference Proceedings (OSTI)

In this report, we discuss some of the advances in surface science and theory that have ena bled a more detailed understanding of the mechanisms that govern the electrocatalysis.More specifically, we examine in detail the electrooxidation ofC1 and Cz alcohol molecules in both acidic and basic media. A combination of detailed in situ spectroscopic measurements along with density functional theory calculations have helped to establish the mechanisms that control the reaction paths and the innuence of acidic and alkaline media. We discuss some of the synergies and differences between electrocatalysis and aqueous phase heterogeneous catalysis.Such analyses begin to establish a common language and framework by which to compare as well as advance both fields.

Braunchweig, B [University of Illinois, Urbana-Champaign; Neurock, Matthew [University of Virginia; Wieckowski, A. [University of Illinois, Urbana-Champaign; Hibbitts, David D [ORNL

2012-01-01T23:59:59.000Z

227

Pyrochlore-Based Catalysts for Syngas-Derived Alcohol Synthesis  

NLE Websites -- All DOE Office Websites (Extended Search)

Pyrochlore-Based Catalysts for Syngas-Derived Pyrochlore-Based Catalysts for Syngas-Derived Alcohol Synthesis Contact NETL Technology Transfer Group techtransfer@netl.doe.gov PON-13-006 August 2013 Opportunity This technology provides an advantageous means to convert syngas into a class of chemicals known as higher oxygenates as well as other long-chain hydrocarbons. Research is currently active on this patent-pending technology "Method of CO and/or CO2 Hydrogenation Using Doped Mixed Metal Oxides." This technology is available for licensing and/or further collaborative research from the U.S. Department of Energy's National Energy Technology Laboratory. Significance * Improves the conversion of syngas from natural gas, coal, or biomass * Enhances the potential use of oxygenates as

228

Catalysts and process for hydrogenolysis of sugar alcohols to polyols  

DOE Patents (OSTI)

The present invention provides a process for preparation of low molecular weight polyols from high molecular weight polyols in a hydrogenolysis reaction under elevated temperature and hydrogen pressure. The process comprises providing in a reaction mixture the polyols, a base, and a metal catalyst prepared by depositing a transition metal salt on an inert support, reducing the metal salt to the metal with hydrogen, and passivating the metal with oxygen, and wherein the catalyst is reduced with hydrogen prior to the reaction. In particular, the process provides for the preparation of glycerol, propylene glycol, and ethylene glycol from sugar alcohols such as sorbitol or xylitol. In a preferred process, the metal catalyst comprises ruthenium which is deposited on an alumina, titania, or carbon support, and the dispersion of the ruthenium on the support increases during the hydrogenolysis reaction.

Chopade, Shubham P. (East Lansing, MI); Miller, Dennis J. (Okemos, MI); Jackson, James E. (Haslett, MI); Werpy, Todd A. (West Richland, WA); Frye, Jr., John G. (Richland, WA); Zacher, Alan H. (Richland, WA)

2001-01-01T23:59:59.000Z

229

Atmospheric Pressure Low Current Plasma for Syngas Production from Alcohol  

E-Print Network (OSTI)

Abstract Atmospheric pressure low current arc discharge between graphite electrodes with conical geometry in liquid ethanol/water mixture was investigated. Syngas production was demonstrated over large experimental conditions. In this paper we focus on discharge aspects. It is shown from pictures that the behavior of low current arc discharge with consumable electrodes represents non-stationary plasma. The energetic properties of plasmas can be used to carry out many applications, particularly in discharge based systems. Recently, research interest focuses on the Non Thermal Plasma (NTP) treatment of hydrocarbons, alcohol, or biomass aimed to improve the yield of synthetic gas (syngas: H2+CO) production at low cost [1, 4]. Experiments were performed on a plasma reactor consisting of two graphite electrodes with conical shape

Ahmed Khacef; Khadija Arabi; Olivier Aubry; Jean Marie Cormier

2012-01-01T23:59:59.000Z

230

Section 1: Agency Policy and Strategy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Sustainability Performance Plan Report to: The Council on Environmental Quality The Office of Management and Budget June 2, 2010 U.S. Department of ENERGY United States Department of Energy Washington, DC 20585 Strategic Sustainability Performance Plan Discovering Sustainable Solutions to Power and Secure America's Future Report to The White House Council on Environmental Quality and Office of Management and Budget September 2010 Department of Energy ii Department of Energy iii Department of Energy Strategic Sustainability Performance Plan Discovering Sustainable Solutions to Power and Secure America's Future Table of Contents Section 1: Department Policy and Strategy.................................................. 1

231

Section 1: Agency Policy and Strategy  

NLE Websites -- All DOE Office Websites (Extended Search)

Sustainability Performance Plan Report to: The Council on Environmental Quality The Office of Management and Budget June 2, 2010 U.S. Department of ENERGY United States Department of Energy Washington, DC 20585 Strategic Sustainability Performance Plan Discovering Sustainable Solutions to Power and Secure America's Future Report to The White House Council on Environmental Quality and Office of Management and Budget September 2010 Department of Energy ii Department of Energy iii Department of Energy Strategic Sustainability Performance Plan Discovering Sustainable Solutions to Power and Secure America's Future Table of Contents Section 1: Department Policy and Strategy.................................................. 1

232

Section 5 -Page 1 5.0) CHEMICAL SAFETY  

E-Print Network (OSTI)

, hereafter referred to as the University of Kansas Chemical Hazard Communication Program (KU-CHCP), has been of the University's Safety and Health Policy. Application The KU-CHCP applies to all chemicals or chemical products. Exceptions - chemicals to which the KU-CHCP does not apply: · Food, drugs, cosmetics, or alcoholic beverages

Peterson, Blake R.

233

Design and development of eco-friendly alcohol engine fitted with waste heat recovery system  

Science Conference Proceedings (OSTI)

The present paper discusses the design and development of an eco-friendly alcohol engine fitted with the waste heat recovery system as a remedial alternative to the existing commonly used internal combustion engine. With the present trends in Internal ...

G. Vijayan Iyer; Nikos E. Mastorakis

2006-06-01T23:59:59.000Z

234

Cloning and sequencing of the alcohol dehydrogenase II gene from Zymomonas mobilis  

DOE Patents (OSTI)

The alcohol dehydrogenase II gene from Zymomonas mobilis has been cloned and sequenced. This gene can be expressed at high levels in other organisms to produce acetaldehyde or to convert acetaldehyde to ethanol.

Ingram, Lonnie O. (Gainesville, FL); Conway, Tyrrell (Gainesville, FL)

1992-01-01T23:59:59.000Z

235

Drug and alcohol abuse: the bases for employee assistance programs in the nuclear-utility industry  

SciTech Connect

This report describes the nature, prevalence, and trends of drug and alcohol abuse among members of the US adult population and among personnel in non-nuclear industries. Analogous data specific to the nuclear utility industry are not available, so these data were gathered in order to provide a basis for regulatory planning. The nature, prevalence, and trend inforamtion was gathered using a computerized literature, telephone discussions with experts, and interviews with employee assistance program representatives from the Seattle area. This report also evaluates the possible impacts that drugs and alcohol might have on nuclear-related job performance, based on currently available nuclear utility job descriptions and on the scientific literature regarding the impairing effects of drugs and alcohol on human performance. Employee assistance programs, which can be used to minimize or eliminate job performance decrements resulting from drug or alcohol abuse, are also discussed.

Radford, L.R.; Rankin, W.L.; Barnes, V.; McGuire, M.V.; Hope, A.M.

1983-07-01T23:59:59.000Z

236

Use of plastic construction materials in small-scale fuel alcohol production  

Science Conference Proceedings (OSTI)

Several general designs for small-scale fuel alcohol plants that have been published primarily use conventional materials of construction (steel, copper, etc.). A fuel alcohol plant owned by Dixie Fuels, Inc. Valley Park, Mississippi, and a farm-scale alcohol plant being developed by the Tennessee Valley Authority have incorporated plastic materials in several areas of their plants; results have been excellent in terms of reduced materials, labor, and operating costs. However, plastics were not used in the distillation step. This work investigated the suitability of small-scale distillation equipment made entirely or partially from plastics. A low-cost alcohol distillation system can be constructed using chlorinated poly(viny chloride) (CPVC) pipe or poly(vinly chloride) (PVC) plastic pipe for the column and heat-exchanger shells. Although pipe made from CPVC is preferred, schedule 80 PVC pipe can be used if external supports are used to provide rigidity. 3 figures, 1 table. (DP)

Lightsey, G.R.; Kadir, O.

1982-01-01T23:59:59.000Z

237

Some economic implications of the utilization of alcohol for the production of energy  

SciTech Connect

The production rate of ethanol per unit of land was examined for different crops and the order of magnitude of the costs was calculated. Alcohol production programs in Brazil, Thailand and Sudan are described.

Bennett, M.C.

1980-01-01T23:59:59.000Z

238

Production of Mixed Alcohols from Bio-syngas over Mo-based Catalyst  

Science Conference Proceedings (OSTI)

A series of Mo-based catalysts prepared by sol-gel method using citric acid as complexant were successfully applied in the high efficient production of mixed alcohols from bio-syngas

Song-bai Qiu; Wei-wei Huang; Yong Xu; Lu Liu; Quan-xin Li

2011-01-01T23:59:59.000Z

239

Consent Order of Dismissal, Section III  

NLE Websites -- All DOE Office Websites (Extended Search)

3 3 SRR-ESH-2013-00054 Revision 1 August 28, 2013 Page 1 of 6 Consent Order of Dismissal, Section III.7 Z-Area Saltstone Disposal Facility Permit General Condition B.5.a-h Information Permit Condition Requirement Estimated Value Updated Value Comments B.5 a) Cumulative process volume of salt waste disposed to date Not Applicable 7,845 kgals Vault 4, Cells B, D, E, F, H, J, K, L SDU 2, Cells 2A and 2B b) Process volume of saltstone grout disposed and vault/disposal unit location (including cell identity) for the reporting period Not Applicable 3.0 x 10 2 kgals SDU 2, Cell 2A 2.6 x 10 2 kgals SDU 2, Cell 2B c) Cumulative process volume of saltstone grout disposed to date Not Applicable 1.4 x 10 4 kgals Vault 4, Cells B, D, E, F, H, J, K, L

240

Sensors Chapter of the IEEE Richland Section  

NLE Websites -- All DOE Office Websites (Extended Search)

MEETING MEETING of the Sensors Chapter of the IEEE Richland Section Wednesday, 27 August 2008 Dr. Wassana Yantasee, PNNL presenting Next-generation metal analyzers based on nanomaterials for biomonitoring and environmental monitoring Abstract: Large numbers of industrial workers are regularly expose to toxic heavy metals like mercury (Hg), cadmium (Cd), and lead (Pb), which are known to induce various diseases that are detrimental to human health. In order to monitor workers for multiple toxic metal exposures and to ensure that these exposures are below a threshold for inducing permanent damage to various organ systems, real-time, non-invasive tools for monitoring of workplace and workers for toxic metal exposure is highly desirable. The portable metal analyzers are also highly beneficial to environmental monitoring of these toxic metals (e.g., in surface water, ground water,

Note: This page contains sample records for the topic "alcohol msds section" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


241

American Bar Association Section on Environment | Open Energy Information  

Open Energy Info (EERE)

Bar Association Section on Environment Bar Association Section on Environment Jump to: navigation, search Name American Bar Association Section on Environment Place Chicago, Illinois Zip 60610 Product The Section of Environment, Energy, and Resources is the premier forum for lawyers working in areas related to environment law, natural resources law, and energy law. References American Bar Association Section on Environment[1] LinkedIn Connections CrunchBase Profile No CrunchBase profile. Create one now! This article is a stub. You can help OpenEI by expanding it. American Bar Association Section on Environment is a company located in Chicago, Illinois . References ↑ "American Bar Association Section on Environment" Retrieved from "http://en.openei.org/w/index.php?title=American_Bar_Association_Section_on_Environment&oldid=342108

242

Draft Report to Congress: Energy Policy Act of 2005, Section...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Draft Report to Congress: Energy Policy Act of 2005, Section 1813, Indian Land Rights-of-Way Study Draft Report to Congress: Energy Policy Act of 2005, Section 1813, Indian Land...

243

Systematic Adjustments of Hydrographic Sections for Internal Consistency  

Science Conference Proceedings (OSTI)

A significant legacy of the World Ocean Circulation Experiment (WOCE) is the large number of high quality, high-resolution, full-depth, transoceanic hydrographic sections occupied starting in the mid-1980s. The section data provide an ...

Gregory C. Johnson; Paul E. Robbins; Gwyneth E. Hufford

2001-07-01T23:59:59.000Z

244

DEPARTMENT ORIENTATION CHECKLIST SECTION A: EMPLOYEE/POSITION INFORMATION  

E-Print Network (OSTI)

DEPARTMENT ORIENTATION CHECKLIST SECTION A: EMPLOYEE/POSITION INFORMATION Department Start Date: ___________________ SECTION B: DEPARTMENT ORIENTATION 1. Introductions Colleagues Department Orientation Partner 2. Department Information Philosophy/Objectives University Policies Telephone system

245

Design of clamping mechanism for securing sections of unmanned submarine  

E-Print Network (OSTI)

A clamping mechanism was designed for securing together two sections of a 12.75" diameter autonomous underwater vehicle. Two semicylindrical sections are secured together by sixteen 1/4"-20 bolts around the machined ends ...

Aronson, Reuben M

2012-01-01T23:59:59.000Z

246

Experiments on Antiprotons: Antiproton-Nucleon Cross Sections  

DOE R&D Accomplishments (OSTI)

In this paper experiments are reported on annihilation and scattering of antiprotons in H{sub 2}O , D{sub 2}O, and O{sub 2}. From the data measured it is possible to obtain an antiproton-proton and an antiproton-deuteron cross section at 457 Mev (lab). Further analysis gives the p-p and p-n cross sections as 104 mb for the p-p reaction cross section and 113 mb for the p-n reaction cross section. The respective annihilation cross sections are 89 and 74 mb. The Glauber correction necessary in order to pass from the p-d to the p-n cross section by subtraction of the p-p cross section is unfortunately large and somewhat uncertain. The data are compared with the p-p and p-n cross sections and with other results on p-p collisions.

Chamberlain, Owen; Keller, Donald V.; Mermond, Ronald; Segre, Emilio; Steiner, Herbert M.; Ypsilantis, Tom

1957-07-22T23:59:59.000Z

247

Partial oxidation for improved cold starts in alcohol-fueled engines: Phase 2 topical report  

DOE Green Energy (OSTI)

Alcohol fuels exhibit poor cold-start performance because of their low volatility. Neat alcohol engines become difficult, if not impossible, to start at temperatures close to or below freezing. Improvements in the cold-start performance (both time to start and emissions) are essential to capture the full benefits of alcohols as an alternative transportation fuel. The objective of this project was to develop a neat alcohol partial oxidation (POX) reforming technology to improve an alcohol engine`s ability to start at low temperatures (as low as {minus}30 C) and to reduce its cold-start emissions. The project emphasis was on fuel-grade ethanol (E95) but the technology can be easily extended to other alcohol fuels. Ultimately a compact, on-vehicle, ethanol POX reactor was developed as a fuel system component to produce a hydrogen-rich, fuel-gas mixture for cold starts. The POX reactor is an easily controllable combustion device that allows flexibility during engine startup even in the most extreme conditions. It is a small device that is mounted directly onto the engine intake manifold. The gaseous fuel products (or reformate) from the POX reactor exit the chamber and enter the intake manifold, either replacing or supplementing the standard ethanol fuel consumed during an engine start. The combustion of the reformate during startup can reduce engine start time and tail-pipe emissions.

NONE

1998-04-01T23:59:59.000Z

248

Why understanding neutrino cross sections is important for astrophysics  

Science Conference Proceedings (OSTI)

Neutrino cross sections are important in many different astrophysical environments. Particularly needed is information about low energy (tens of MeV) cross sections. We review, for a few situations, the importance of neutrino cross sections for supernovae, gamma ray bursts and neutron stars.

McLaughlin, G. C. [Department of Physics North Carolina State University, Raleigh, NC 27695-8202 (United States)

2007-12-21T23:59:59.000Z

249

Process for the synthesis of aliphatic alcohol-containing mixtures  

DOE Patents (OSTI)

A process for the synthesis of mixtures which include saturated aliphatic alcohols is disclosed. In the first step of the process, the first catalyst activation stage, a catalyst, which comprises the oxides of copper, zinc, aluminum, potassium and one or two additional metals selected from the group consisting of chromium, magnesium, cerium, cobalt, thorium and lanthanum, is partially activated. In this step, a reducing gas stream, which includes hydrogen and at least one inert gas, flows past the catalyst at a space velocity of up to 5,000 liters (STP) per hour, per kilogram of catalyst. The partially activated catalyst is then subjected to the second step of the process, second-stage catalyst activation. In this step, the catalyst is contacted by an activation gas stream comprising hydrogen and carbon monoxide present in a volume ratio of 0.5:1 and 4:1, respectively, at a temperature of 200.degree. to 450.degree. C. and a pressure of between 35 and 200 atmospheres. The activation gas flows at a space velocity of from 1,000 to 20,000 liters (STP) per hour, per kilogram of catalyst. Second-stage activation continues until the catalyst is contacted with at least 500,000 liters (STP) of activation gas per kilogram of catalyst. The fully activated catalyst, in the third step of the process, contacts a synthesis gas stream comprising hydrogen and carbon monoxide.

Greene, Marvin I. (Oradell, NJ); Gelbein, Abraham P. (Morristown, NJ)

1984-01-01T23:59:59.000Z

250

PROMOTED ZINC CHROMITE CATALYSTS FOR HIGHER ALCOHOL SYNTHESIS  

DOE Green Energy (OSTI)

This report describes the analytical protocols that were developed during the last two years to analyze ''spent'' THQ (tetrahydroquinoline) slurry liquid. Identification of the components of the ''spent'' THQ should help to understand the influence of the slurry medium on the methanol synthesis reaction, and on other reactions with THQ as the slurry liquid. Silica gel liquid chromatography and high performance liquid chromatography (HPLC) were used to isolate and purify the major compounds in the ''spent'' slurry liquid. Gas chromatography/mass spectroscopy (GC/MS), Fourier transform infrared (FTIR) and nuclear magnetic resonance (NMR) were applied to identify the major compounds. Methyl-, dimethyl-, and trimethyl-THQ were found to comprise more than 80% of the ''spent'' liquid. The balance was various methylated indoles. A methyl group always is attached to the N atom in the ring structure. Speculative mechanisms are presented that may help to understand the interaction between the catalyst and the alkylated THQ slurry liquid, and the effect of liquid composition on the methanol synthesis reaction. A poster entitled ''Promoted Zinc Chromite Catalyst for Higher Alcohol Synthesis in a Slurry Reactor-2. Spent Liquid Analysis'' was presented at the AIChE National Meeting, Los Angeles, CA, Nov 12-17, 2000.

Ms. Xiaolei Sun; Professor George W. Roberts

2001-06-15T23:59:59.000Z

251

Separation of alcohol-water mixtures using salts  

DOE Green Energy (OSTI)

Use of a salt (KF or Na/sub 2/SO/sub 4/) to induce phase separation of alcohol-water mixtures was investigated in three process flowsheets to compare operating and capital costs with a conventional distillation process. The process feed was the Clostridia fermentation product, composed of 98 wt % water and 2 wt % solvents (70% 1-butanol, 27% 2-propanol, and 3% ethanol). The design basis was 150 x 10/sup 6/ kg/y of solvents. Phase equilibria and tieline data were obtained from literature and experiments. Three separation-process designs were developed and compared by an incremental economic analysis (+-30%) with the conventional separation technique using distillation alone. The cost of salt recovery for recycle was found to be the critical feature. High capital and operating costs make recovery of salt by precipitation uneconomical; however, a separation scheme using multiple-effect evaporation for salt recovery has comparable incremental capital costs ($1.72 x 10/sup 6/ vs $1.76 x 10/sup 6/) and lower incremental operating costs ($2.14 x 10/sup 6//y vs $4.83 x 10/sup 6//y) than the conventional separation process.

Card, J. C.; Farrell, L. M.

1982-04-01T23:59:59.000Z

252

High octane ethers from synthesis gas-derived alcohols  

SciTech Connect

The temperature dependence of ether synthesis, particularly unsymmetric methylisobutylether (MIBE), was carried out over the Nafion-H microsaddles (MS) catalyst. The principal product formed under the rather severe reaction conditions of 1100 psig pressure and temperatures in the range of 123--157{degree}C was the expected MIBE formed directly by coupling the methanol/isobutanol reactants. In addition, significantly larger quantities of the dimethylether (DME) and hydrocarbon products were observed than were obtained under milder reaction conditions. Deactivation of the Nafion-H MS catalyst was determined by periodically testing the catalyst under a given set of reaction conditions for the synthesis of MIBE and MTBE from methanol/isobutanol = 2/1, i.e. 123{degree}C, 1100 psig, and total GHSV = 248 mol/kg cat/hr. After carrying out various tests over a period of 2420 hr, with intermittant periods of standing under nitrogen at ambient conditions, the yields of MIBE and MTBE had decreased by 25% and 41%, respectively. In order to gain insight into the role of the surface acidity in promoting the selective coupling of the alcohols to form the unsymmetric ether, the strengths of the acid sites on the catalysts are still being probed by calorimetric titrations in non-aqueous solutions. 11 refs., 13 figs., 9 tabs.

Klier, K.; Herman, R.G.; DeTavernier, S.; Johannson, M.; Kieke, M.; Bastian, R.D.

1991-07-01T23:59:59.000Z

253

Graphs of the cross sections in the recommended Monte Carlo cross-section library at the Los Alamos Scientific Laboratory  

Science Conference Proceedings (OSTI)

Graphs of all neutron cross sections and photon production cross sections on the Recommended Monte Carlo Cross Section (RMCCS) library have been plotted along with local neutron heating numbers. Values for anti ..nu.., the average number of neutrons per fission, are also given.

Soran, P.D.; Seamon, R.E.

1980-05-01T23:59:59.000Z

254

SECTION 13-CHEMICAL SAFETY NOTE: Much of the information contained in this Chemical Safety section is duplicated from the  

E-Print Network (OSTI)

164 SECTION 13- CHEMICAL SAFETY NOTE: Much of the information contained in this Chemical Safety section is duplicated from the "Chemical Hygiene Plan for Laboratories" in the Louisiana Tech University ( Section 12) when working with chemicals. REQULATORY BASIS FOR RULES GOVERNING THE SAFE USE OF CHEMICALS

Selmic, Sandra

255

EIA - Annual Energy Outlook 2008 - Overview Section  

Gasoline and Diesel Fuel Update (EIA)

Overview Overview Annual Energy Outlook 2008 with Projections to 2030 Energy Trends to 2030 In preparing projections for the Annual Energy Outlook 2008 (AEO2008), the Energy Information Administration (EIA) evaluated a wide range of trends and issues that could have major implications for U.S. energy markets between today and 2030. This overview focuses on one case, the reference case, which is presented and compared with the Annual Energy Outlook 2007 (AEO2007) reference case (see Table 1). Readers are encouraged to review the full range of alternative cases included in other sections of AEO2008. As in previous editions of the Annual Energy Outlook (AEO), the reference case assumes that current policies affecting the energy sector remain unchanged throughout the projection period. The reference case provides a clear basis against which alternative cases and policies can be compared. Although current laws and regulations may change over the next 25 years, and new ones may be created, it is not possible to predict what they will be or how they will be implemented [1].

256

SRS FTF Section 3116 Basis for Determination | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

FTF Section 3116 Basis for Determination FTF Section 3116 Basis for Determination SRS FTF Section 3116 Basis for Determination Basis for Section 3116 Determination for Closure of F-Tank Farm at the Savannah River Site. In accordance with NDAA Section 3116, certain waste from reprocessing of spent nuclear fuel is not high-level waste if the Secretary of Energy, in consultation with the NRC, determines that the criteria in NDAA Section 3116(a) are met. This FTF 3116 Basis Document shows that those criteria are satisfied, to support a determination that the Secretary may make pursuant to NDAA Section 3116. This FTF 3116 Basis Document concerns the stabilized residuals in waste tanks and ancillary structures, those waste tanks, and the ancillary structures (including integral equipment) at the SRS FTF at the time of closure.

257

Geothermal source potential and utilization for methane generation and alcohol production  

DOE Green Energy (OSTI)

A study was conducted to assess the technical and economic feasibility of integrating a geothermally heated anaerobic digester with a fuel alcohol plant and cattle feedlot. Thin stillage produced from the alcohol production process and manure collected from the cattle feedlot would be digested in anaerobic digesters to produce biogas, a mixture of methane and carbon dioxide, and residue. The energy requirements to maintain proper digester temperatures would be provided by geothermal water. The biogas produced in the digesters would be burned in a boiler to produce low-pressure steam which would be used in the alcohol production process. The alcohol plant would be sized so that the distiller's grains byproduct resulting from the alcohol production would be adequate to supply the daily cattle feed requirements. A portion of the digester residue would substitute for alfalfa hay in the cattle feedlot ration. The major design criterion for the integrated facilty was the production of adequate distiller's grain to supply the daily requirements of 1700 head of cattle. It was determined that, for a ration of 7 pounds of distiller's grain per head per day, a 1 million gpy alcohol facility would be required. An order-of-magnitude cost estimate was prepared for the proposed project, operating costs were calculated for a facility based on a corn feedstock, the economic feasibility of the proposed project was examined by calculating its simple payback, and an analysis was performed to examine the sensitivity of the project's economic viability to variations in feedstock costs and alcohol and distiller's grain prices.

Austin, J.C.

1981-11-01T23:59:59.000Z

258

Assessment of ether and alcohol fuels from coal. Volume 2. Technical report  

DOE Green Energy (OSTI)

A unique route for the indirect liquefaction of coal to produce transportation fuel has been evaluated. The resultant fuel includes alkyl tertiary alkyl ethers and higher alcohols, all in the gasoline boiling range. When blended into gasoline, the ether fuel provides several advantages over the lower alcohols: (1) lower chemical oxygen content, (2) less-severe water-separation problems, and (3) reduced front-end volatility effects. The ether fuel also has high-octane quality. Further, it can be utilized as a gasoline substitute in all proportions. Production of ether fuel combines several steps, all of which are or have been practiced on an industrial scale: (1) coal gasification, (2) gas cleanup and shift to desired H/sub 2/:CO ratio, (3) conversion of synthesis gas to isobutanol, methanol, and higher alcohols, (4) separation of alcohols, (5) chemical dehydration of isobutanol to isobutylene, and (6) etherification of isobutylene with methanol. A pilot-plant investigation of the isobutanol synthesis step was performed. Estimates of ether-fuel manufacturing costs indicate this process route is significantly more costly than synthesis of methanol. However, the fuel performance features provide incentive for developing the necessary process and catalyst improvements. Co-production of higher-molecular-weight co-solvent alcohols represents a less-drastic form of methanol modification to achieve improvement in the performance of methanol-gasoline blends. Costs were estimated for producing several proportions of methanol plus higher alcohols from coal. Estimated fuel selling price increases regularly but modestly with higher alcohol content.

Not Available

1983-03-01T23:59:59.000Z

259

Impact of timing of alcohol use initiation and depressed mood on risky substance use among urban minority adolescents.  

E-Print Network (OSTI)

??The current study involved the investigation of two research areas: (1) the effect of timing of alcohol use initiation on risky substance use in mid-adolescence, (more)

Boohar, Ellen Moore

2004-01-01T23:59:59.000Z

260

Help! I need somebody (not just anybody) - the folktale's helper in personal experience narratives of recovering alcoholics.  

E-Print Network (OSTI)

??This thesis explores the personal experience narratives of nine recovering alcoholics through the lens of folktale scholarship. Using Propp's structuralist model developed for folktales, I (more)

Baker, Jedediah, 1980-

2008-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "alcohol msds section" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


261

METAL MEDIA FILTERS, AG-1 SECTION FI  

Science Conference Proceedings (OSTI)

One application of metal media filters is in various nuclear air cleaning processes including applications for protecting workers, the public and the environment from hazardous and radioactive particles. To support this application the development of the ASME AG-1 FI Standard on Metal Media has been under way for more than ten years. Development of the proposed section has required resolving several difficult issues associated with operating conditions (media velocity, pressure drop, etc.), qualification testing, and quality acceptance testing. Performance characteristics of metal media are dramatically different than the glass fiber media with respect to parameters like differential pressures, operating temperatures, media strength, etc. These differences make existing data for a glass fiber media inadequate for qualifying a metal media filter for AG-1. In the past much work has been conducted on metal media filters at facilities such as Lawrence Livermore National Laboratory (LLNL) and Savannah River National Laboratory (SRNL) to qualify the media as High Efficiency Particulate Air (HEPA) Filters. Particle retention testing has been conducted at Oak Ridge Filter Test Facility and at Air Techniques International (ATI) to prove that the metal media meets or exceeds the 99.97% particle retention required for a HEPA Filter. Even with his testing, data was lacking to complete an AG-1 FI Standard on metal media. With funding secured by Mississippi State University (MSU) from National Nuclear Security Administration (NNSA), a research test stand is being designed and fabricated at MSU's Institute for Clean Energy Technology (ICET) Facility to obtain qualification data on metal media. This in turn will support required data needed for the FI Standard. The paper will discuss in detail how the test stand at MSU will obtain the necessary data to complete the FI Standard.

Adamson, D.

2012-05-23T23:59:59.000Z

262

Apparatus and methods for installing, removing and adjusting an inner turbine shell section relative to an outer turbine shell section  

DOE Patents (OSTI)

A turbine includes upper and lower inner shell sections mounting the nozzles and shrouds and which inner shell is supported by pins secured to a surrounding outer shell. To disassemble the turbine for access to the inner shell sections and rotor, an alignment fixture is secured to the lower outer shell section and has pins engaging the inner shell section. To disassemble the turbine, the inner shell weight is transferred to the lower outer shell section via the alignment fixture and cradle pins. Roller assemblies are inserted through access openings vacated by support pins to permit rotation of the lower inner shell section out of and into the lower outer shell section during disassembly and assembly. The alignment fixture includes adjusting rods for adjusting the inner shell axially, vertically, laterally and about a lateral axis. A roller over-cage is provided to rotate the inner shell and a dummy shell to facilitate assembly and disassembly in the field.

Leach, David (Niskayuna, NY); Bergendahl, Peter Allen (Scotia, NY); Waldo, Stuart Forrest (Salem, NC); Smith, Robert Leroy (Milford, OH); Phelps, Robert Kim (Milford, OH)

2001-01-01T23:59:59.000Z

263

Alcoholic fermentation of raw cassava starch by Rhizopus koji without cooking  

Science Conference Proceedings (OSTI)

Using only wheat bran koji from the Rhizopus strain, raw cassava starch and cassava pellets converted reasonably well to alcohol (ethanol) without cooking at 35 degrees C and pH 4.5-5.0. When the initial broth contained 30 g raw cassava starch, 10 g Rhizopus species koji, and 100 mL tap water, 12.1 g of alcohol was recovered by final distillation from fermented broth. In this case, 12.1 g alcohol corresponds to an 85.5% conversion rate based on the theoretical value of the starch content. When the initial broth contained 40 g cassava starch, 14.1 g of alcohol was recovered, where 14.1 g corresponds to a 74.5% conversion rate. The alcoholic fermentation process described in the present work is considered more effective and reasonable than the process using raw starch without cooking reported until now, since the new process makes it unnecessary to add yeast cells and glucoamylase preparation. (Refs. 15).

Fuijo, Y.; Suyanadona, P.; Attasampunna, P.; Ueda, S.

1984-04-01T23:59:59.000Z

264

Alcoholic fermentation of raw cassava starch by Rhizopus koji without cooking  

Science Conference Proceedings (OSTI)

Using only wheat bran koji from the Rhizopus strain, raw cassava starch and casava pellets converted reasonably well to alcohol (ethanol) without cooking at 35/sup 0/C and pH 4.5-5.0. When the initial broth contained 30 g raw cassava starch, 10 g Rhizopus sp. koji, and 100 mL tap water, 12.1 g of alcohol was recovered by final distillation from fermented broth. In this case, 12.1 g alcohol corresponds to an 85.5% conversion rate based on the theoretical value of the starch content. When the initial broth contained 40 g cassava starch, 14.1 g of alcohol was recovered, where 14.1 g corresponds to a 74.5% conversion rate. The alcoholic fermentation process described in the present work is considered more effective and reasonable than the process using raw starch without cooking reported until now, since the new process makes it unnecessary to add yeast cells and glucoamylase preparation.

Fujio, Y.; Suyanadona, P.; Attasampunna, P.; Ueda, S.

1984-01-01T23:59:59.000Z

265

The Non-alcoholic Beverage Market in the United States: Demand Interrelationships, Dynamics, Nutrition Issues and Probability Forecast Evaluation  

E-Print Network (OSTI)

There are many different types of non-alcoholic beverages (NAB) available in the United States today compared to a decade ago. Additionally, the needs of beverage consumers have evolved over the years centering attention on functionality and health dimensions. These trends in volume of consumption are a testament to the growth in the NAB industry. Our study pertains to ten NAB categories. We developed and employed a unique cross-sectional and time-series data set based on Nielsen Homescan data associated with household purchases of NAB from 1998 through 2003. First, we considered demographic and economic profiling of the consumption of NAB in a two-stage model. Race, region, age and presence of children and gender of household head were the most important factors affecting the choice and level of consumption. Second, we used expectation-prediction success tables, calibration, resolution, the Brier score and the Yates partition of the Brier score to measure the accuracy of predictions generated from qualitative choice models used to model the purchase decision of NAB by U.S. households. The Yates partition of the Brier score outperformed all other measures. Third, we modeled demand interrelationships, dynamics and habits of NAB consumption estimating own-price, cross-price and expenditure elasticities. The Quadratic Almost Ideal Demand System, the synthetic Barten model and the State Adjustment Model were used. Soft drinks were substitutes and fruit juices were complements for most of non-alcoholic beverages. Investigation of a proposed tax on sugar-sweetened beverages revealed the importance of centering attention not only to direct effects but also to indirect effects of taxes on beverage consumption. Finally, we investigated factors affecting nutritional contributions derived from consumption of NAB. Also, we ascertained the impact of the USDA year 2000 Dietary Guidelines for Americans associated with the consumption of NAB. Significant factors affecting caloric and nutrient intake from NAB were price, employment status of household head, region, race, presence of children and the gender of household food manager. Furthermore, we found that USDA nutrition intervention program was successful in reducing caloric and caffeine intake from consumption of NAB. The away-from-home intake of beverages and potential impacts of NAB advertising are not captured in our work. In future work, we plan to address these limitations.

Dharmasena, Kalu Arachchillage Senarath

2010-05-01T23:59:59.000Z

266

Energy Independence and Security Act, Section 432: Federal Facility  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Energy Independence and Security Act, Section 432: Federal Facility Energy Independence and Security Act, Section 432: Federal Facility Management and Benchmarking Requirements Energy Independence and Security Act, Section 432: Federal Facility Management and Benchmarking Requirements October 8, 2013 - 2:02pm Addthis Section 432 of the Energy Independence and Security Act of 2007 requires agencies to report Federal facility energy and water use. Section 432 of the Energy Independence and Security Act of 2007 requires agencies to report Federal facility energy and water use. The Federal Energy Management Program (FEMP) is responsible for tracking Federal agency progress toward meeting Section 432 of the Energy Independence and Security Act (EISA) of 2007 for Federal facility energy and water management and benchmarking. The EISA 432 Compliance Tracking System (EISA 432 CTS) tracks agency

267

NDAA Section 3116 Waste Determinations with Related Disposal Performance  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

NDAA Section NDAA Section 3116 Waste Determinations with Related Disposal Performance Assessments NDAA Section 3116 Waste Determinations with Related Disposal Performance Assessments Section 3116 of the Ronald W. Reagan National Defense Authorization Act for Fiscal Year 2005 authorizes the Secretary of Energy, in consultation with the Nuclear Regulatory Commission, to reclassify certain waste from reprocessing spent nuclear fuel from high-level waste to low-level waste if it meets the criteria set forth in Section 3116. Section 3116 is currently only applicable to Idaho National Laboratory (INL) and the Savannah River Site (SRS). The other two DOE sites with similar waste (residuals remaining after cleaning out tanks and equipment that held liquid high-level waste)

268

Criticality benchmark comparisons leading to cross-section upgrades  

Science Conference Proceedings (OSTI)

For several years criticality benchmark calculations with COG. COG is a point-wise Monte Carlo code developed at Lawrence Livermore National Laboratory (LLNL). It solves the Boltzmann equation for the transport of neutrons and photons. The principle consideration in developing COG was that the resulting calculation would be as accurate as the point-wise cross-sectional data, since no physics computational approximations were used. The objective of this paper is to report on COG results for criticality benchmark experiments in concert with MCNP comparisons which are resulting in corrections an upgrades to the point-wise ENDL cross-section data libraries. Benchmarking discrepancies reported here indicated difficulties in the Evaluated Nuclear Data Livermore (ENDL) cross-sections for U-238 at thermal neutron energy levels. This led to a re-evaluation and selection of the appropriate cross-section values from several cross-section sets available (ENDL, ENDF/B-V). Further cross-section upgrades anticipated.

Alesso, H.P.; Annese, C.E.; Heinrichs, D.P.; Lloyd, W.R.; Lent, E.M.

1993-03-01T23:59:59.000Z

269

SUMMARY OF REGULATIONS IMPLEMENTING FEDERAL POWER ACT SECTION 216 |  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

SUMMARY OF REGULATIONS IMPLEMENTING FEDERAL POWER ACT SECTION 216 SUMMARY OF REGULATIONS IMPLEMENTING FEDERAL POWER ACT SECTION 216 SUMMARY OF REGULATIONS IMPLEMENTING FEDERAL POWER ACT SECTION 216 The Energy Policy Act of 2005 added section 216(h) to the Federal Power Act providing for the Department of Energy to act as the lead agency for coordinating all applicable Federal authorizations and related environmental reviews required under Federal law in order to site an electric transmission facility. The Act authorized DOE to issue any regulations necessary to implement the provisions of 216(h). SUMMARY OF REGULATIONS IMPLEMENTING FEDERAL POWER ACT SECTION 216 More Documents & Publications SUMMARY OF REGULATIONS IMPLEMENTING FEDERAL POWER ACT SECTION 216 Comments on Notice of Proposed Rulemaking for Coordination of Federal

270

The Geometry of General Phase Diagram Sections - Programmaster ...  

Science Conference Proceedings (OSTI)

It is shown that all proper phase diagram sections obey the same simple set of geometrical rules, and the choices of axes and constants that ensure that a...

271

IAEA Planning and Economic Studies Section (PESS) Capacity Building | Open  

Open Energy Info (EERE)

IAEA Planning and Economic Studies Section (PESS) Capacity Building IAEA Planning and Economic Studies Section (PESS) Capacity Building Jump to: navigation, search Tool Summary Name: IAEA Planning and Economic Studies Section (PESS) Capacity Building Agency/Company /Organization: International Atomic Energy Agency Sector: Energy Focus Area: Non-renewable Energy, Energy Efficiency, Renewable Energy Topics: Pathways analysis Resource Type: Software/modeling tools, Training materials References: IAEA PESS capacity building[1] Logo: IAEA Planning and Economic Studies Section (PESS) Capacity Building "PESS offers assistance to Member States, particularly from developing regions, to improve their energy system analysis & planning capabilities. Assistance can include: transferring modern planning methods, tools and databanks

272

DOE EAC Electricity Adequacy Report. Transmission Section - September 15,  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Transmission Section - Transmission Section - September 15, 2008 DOE EAC Electricity Adequacy Report. Transmission Section - September 15, 2008 There is a critical need to upgrade the nation's electric transmission grid. Two reasons in particular drive this need. First, increasing transmission capability will help ensure a reliable electric supply and provide greater access to economically-priced power. Second, with the growth in state-adopted renewable performance standards (RPS) and the increasing possibility of a national RPS, significant new transmission, much of it interregional, is needed to access renewable resources. DOE EAC Electricity Adequacy Report. Transmission Section - September 15, 2008 More Documents & Publications DOE EAC Electricity Adequacy Report. Transmission Chapter DRAFT-

273

Positive Scattering Cross Sections using Constrained Least Squares  

Science Conference Proceedings (OSTI)

A method which creates a positive Legendre expansion from truncated Legendre cross section libraries is presented. The cross section moments of order two and greater are modified by a constrained least squares algorithm, subject to the constraints that the zeroth and first moments remain constant, and that the standard discrete ordinate scattering matrix is positive. A method using the maximum entropy representation of the cross section which reduces the error of these modified moments is also presented. These methods are implemented in PARTISN, and numerical results from a transport calculation using highly anisotropic scattering cross sections with the exponential discontinuous spatial scheme is presented.

Dahl, J.A.; Ganapol, B.D.; Morel, J.E.

1999-09-27T23:59:59.000Z

274

O A Section 2. Coal - Energy Information Administration  

U.S. Energy Information Administration (EIA)

Section 2. Coal Coal Consumption Physical Units Coal in the United States is mostly consumed by the electric power sector. Data are collected by the ...

275

NIST: Electron-Impact Cross Section Database - Ver. History  

Science Conference Proceedings (OSTI)

... date]. Version 3.0 August 2004, Electron-impact cross section data has been added for many molecules and atoms. Version ...

276

NIST: Electron-Impact Cross Section Database - Intro.  

Science Conference Proceedings (OSTI)

... the ionization and excitation of atoms and molecules by electron impact is ... ionization cross sections (energy distribution of ejected electrons) for H ...

277

NDAA Section 3116 Waste Determinations with Related Disposal...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

NDAA Section 3116 Waste Determinations with Related Disposal Performance Assessments Waste Management Nuclear Materials & Waste Tank Waste and Waste Processing Waste...

278

The TriBeam System: Femtosecond Laser Based Serial Sectioning  

Science Conference Proceedings (OSTI)

Presentation Title, The TriBeam System: Femtosecond Laser Based Serial Sectioning ... Measurement and Quantification of Grain Boundary Evolution in Three...

279

Preliminary Evaluation of the Impact of the Section 1603 Treasury...  

NLE Websites -- All DOE Office Websites (Extended Search)

Preliminary Evaluation of the Impact of the Section 1603 Treasury Grant Program on Renewable Energy Deployment in 2009 Mark Bolinger, Ryan Wiser, Nam Darghouth Environmental...

280

Process to convert biomass and refuse derived fuel to ethers and/or alcohols  

DOE Patents (OSTI)

A process for conversion of a feedstock selected from the group consisting of biomass and refuse derived fuel (RDF) to provide reformulated gasoline components comprising a substantial amount of materials selected from the group consisting of ethers, alcohols, or mixtures thereof, comprising: drying said feedstock; subjecting said dried feedstock to fast pyrolysis using a vortex reactor or other means; catalytically cracking vapors resulting from said pyrolysis using a zeolite catalyst; condensing any aromatic byproduct fraction; catalytically alkylating any benzene present in said vapors after condensation; catalytically oligomerizing any remaining ethylene and propylene to higher olefins; isomerizing said olefins to reactive iso-olefins; and catalytically reacting said iso-olefins with an alcohol to form ethers or with water to form alcohols.

Diebold, James P. (Lakewood, CO); Scahill, John W. (Evergreen, CO); Chum, Helena L. (Arvada, CO); Evans, Robert J. (Lakewood, CO); Rejai, Bahman (Lakewood, CO); Bain, Richard L. (Golden, CO); Overend, Ralph P. (Lakewood, CO)

1996-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "alcohol msds section" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


281

Process to convert biomass and refuse derived fuel to ethers and/or alcohols  

DOE Patents (OSTI)

A process is described for conversion of a feedstock selected from the group consisting of biomass and refuse derived fuel (RDF) to provide reformulated gasoline components comprising a substantial amount of materials selected from the group consisting of ethers, alcohols, or mixtures thereof, comprising: drying said feedstock; subjecting said dried feedstock to fast pyrolysis using a vortex reactor or other means; catalytically cracking vapors resulting from said pyrolysis using a zeolite catalyst; condensing any aromatic byproduct fraction; catalytically alkylating any benzene present in said vapors after condensation; catalytically oligomerizing any remaining ethylene and propylene to higher olefins; isomerizing said olefins to reactive iso-olefins; and catalytically reacting said iso-olefins with an alcohol to form ethers or with water to form alcohols. 35 figs.

Diebold, J.P.; Scahill, J.W.; Chum, H.L.; Evans, R.J.; Rejai, B.; Bain, R.L.; Overend, R.P.

1996-04-02T23:59:59.000Z

282

Operational safety report for the cleaning of non-radioactive, sodium-wetted reactor components with ethyl alcohol  

DOE Green Energy (OSTI)

The safety aspects of the removal of sodium from nonradioactive reactor components by the alcohol process are described in detail. Pertinent properties of alcohol and hydrogen are presented. Relevant excerpts from the Occupational Safety and Health Act safety codes are presented, and a conceptual system is shown illustrating the application of these safety measures.

Humphrey, L.; Felton, L.; Goodman, L.; Pilicy, G.; Welch, F.

1974-01-01T23:59:59.000Z

283

Stability and Lifetime of K-CoMoSx Mixed Alcohol Catalysts  

SciTech Connect

Researchers have studied sulfide-type catalysts for the production of mixed alcohols from synthesis gas for several decades. Despite many advances in the art, these processes are not yet commercial, due in large part to mediocre economics and the added risk associated with uncertainty in catalyst lifetime. This talk will outline some recent studies in the lifetime and stability of K-CoMoSx-type mixed alcohol catalysts. Specifically, studies of long term operation (> 3000h), sulfiding agents, simulated methanol recycle, and morphology (probed via XRD and XPS) will be discussed, with the conclusion that these materials are likely to exhibit acceptable lifetimes in continuous operation.

Hensley, J. E.; Ruddy, D.; Schaidle, J.; Ferrell, J.; Thibodeaux, J.

2013-01-01T23:59:59.000Z

284

Peculiar points in the phase diagram of the water-alcohol solutions  

E-Print Network (OSTI)

The work is devoted to the investigation of nontrivial behavior of dilute water-alcohol solutions. The temperature and concentration dependencies of the contraction for aqueous solutions of ethanol and methanol are analyzed. The existence of a specific point, the so-called peculiar point, was established. It is shown that water-alcohol solutions of different types obey the principle of corresponding states if temperature and volume fraction are used as principal coordinates. In this case, the concentration of the peculiar point for different solutions is close to x_{\

Chechko, V E; Malomuzh, M P

2013-01-01T23:59:59.000Z

285

QUANTUM DOT MULTI-SECTION LIGHT EMITTERS YONGCHUN XIN  

E-Print Network (OSTI)

such as lasers, super-luminescent light emitting diodes, detectors, amplifiers, and solar cells [19, 20]. 1QUANTUM DOT MULTI-SECTION LIGHT EMITTERS BY YONGCHUN XIN B.S., Physics, Peking University, 1996 M. To my son, Alex, you are the greatest gift I have. #12;QUANTUM DOT MULTI-SECTION LIGHT EMITTERS

New Mexico, University of

286

SOLAR BULLETIN Astronomical Society of Southern Africa, Solar Section  

E-Print Network (OSTI)

SOLAR BULLETIN Astronomical Society of Southern Africa, Solar Section Hi Solar friends, Hi Solar friends, As the emphasis in the ASSA group is on observations in the different sections, we in the solar and international solar observations. Observations are used to calculate a monthly Southern African sunspot number

Glass, Ian S.

287

Eliassen-Palm Cross Sections for the Troposphere  

Science Conference Proceedings (OSTI)

Eliassen-Palm (EP) cross sections are meridional cross sections showing the Eliassen-Palm flux F by arrows and its divergence by contours. For large-scale, quasi-geostrophic motion F is defined to have ? and ? components r0 cos?[?u?v?, fv???/?p] where ? is ...

H. J. Edmon Jr.; B. J. Hoskins; M. E. McIntyre

1980-12-01T23:59:59.000Z

288

Advanced Hot Section Materials and Coatings Test Rig  

SciTech Connect

The Hyperbaric Advanced Hot Section Materials & Coating Test Rig program provides design and implementation of a laboratory rig capable of simulating the hot gas path conditions of coal-gas fired industrial gas turbine engines. The principal activities during this reporting period were the continuation of test section detail design and developing specifications for auxiliary systems and facilities.

Dan Davies

2004-10-30T23:59:59.000Z

289

ADVANCED HOT SECTION MATERIALS AND COATINGS TEST RIG  

SciTech Connect

The Hyperbaric Advanced Hot Section Materials & Coating Test Rig program provides design and implementation of a laboratory rig capable of simulating the hot gas path conditions of coal-gas fired industrial gas turbine engines. The principal activity during this reporting period were the evaluation of syngas combustor concepts, the evaluation of test section concepts and the selection of the preferred rig configuration.

Scott Reome; Dan Davies

2004-04-30T23:59:59.000Z

290

Can a Family Farm Benefit from Section 9006?  

DOE Green Energy (OSTI)

Section 9006 of the 2002 U.S. Farm Bill provides grants and guaranteed loans for rural renewable energy and energy efficiency projects. This fact sheet describes how the Tjaden family of Iowa pursued Section 9006 funding in pursuit of a wind turbine for their family farm.

Not Available

2005-05-01T23:59:59.000Z

291

Bit section instruction set extension of ARM for embedded applications  

Science Conference Proceedings (OSTI)

Programs that manipulate data at subword level, i.e. bit sections within a word, are common place in the embedded domain. Examples of such applications include media processing as well as network processing codes. These applications spend significant ... Keywords: bit section operations, multimedia data, network processing

Bengu Li; Rajiv Gupta

2002-10-01T23:59:59.000Z

292

Nuclear Science and Technology, November 2000. NEUTRON CROSS SECTION EVALUATIONS  

E-Print Network (OSTI)

Nuclear Science and Technology, November 2000. 1 NEUTRON CROSS SECTION EVALUATIONS FOR 238 U UP and Power Engineering, 249020 Obninsk, Russia A.Ventura ENEA, Nuclear Data Center and INFN, Bologna Section of the statistical description that includes direct, pre-equilibrium and equilibrium mechanisms of nuclear reactions

293

Fission Cross Section Measurements of Actinides at LANSCE  

Science Conference Proceedings (OSTI)

Fission cross sections of a range of actinides have been measured at the Los Alamos Neutron Science Center (LANSCE) in support of nuclear energy applications. By combining measurement at two LANSCE facilities, Lujan Center and the Weapons Neutron Research center (WNR), differential cross sections can be measured from sub-thermal energies up to 200 MeV. Incident neutron energies are determined using the time-of-flight method, and parallel-plate ionization chambers are used to measure fission cross sections relative to the 235U standard. Recent measurements include the 233, 238U, 239-242Pu, and 243Am neutron-induced fission cross sections. In this paper preliminary results for fission cross sections of 243Am and 233U will be presented.

F. Tovesson; A. B. Laptev; T. S. Hill

2011-08-01T23:59:59.000Z

294

Department of Energy (DOE) and Section 508 | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Department of Energy (DOE) and Section 508 Department of Energy (DOE) and Section 508 Department of Energy (DOE) and Section 508 In 1998, Congress amended the Rehabilitation Act to require Federal agencies to make their electronic and information technology accessible to people with disabilities. Inaccessible technology interferes with an individual's ability to obtain and use information quickly and easily. Section 508 was enacted to eliminate barriers in information technology, to make available new opportunities for people with disabilities, and to encourage development of technologies that will help achieve these goals. The law applies to all Federal agencies when they develop, procure, maintain, or use electronic and information technology. Under Section 508 (29 U.S.C. 794d), agencies must give disabled employees and members of the

295

Energy Independence and Security Act, Section 432: Federal Facility  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Facility Reporting » Energy Independence and Facility Reporting » Energy Independence and Security Act, Section 432: Federal Facility Management and Benchmarking Requirements Energy Independence and Security Act, Section 432: Federal Facility Management and Benchmarking Requirements October 8, 2013 - 2:02pm Addthis Section 432 of the Energy Independence and Security Act of 2007 requires agencies to report Federal facility energy and water use. Section 432 of the Energy Independence and Security Act of 2007 requires agencies to report Federal facility energy and water use. The Federal Energy Management Program (FEMP) is responsible for tracking Federal agency progress toward meeting Section 432 of the Energy Independence and Security Act (EISA) of 2007 for Federal facility energy and water management and benchmarking.

296

Clean Air Act, Section 309 | Department of Energy  

NLE Websites -- All DOE Office Websites (Extended Search)

Clean Air Act, Section 309 Clean Air Act, Section 309 Clean Air Act, Section 309 The Administrator shall review and comment in writing on the environmental impact of any matter relating to duties and responsibilities granted pursuant to this chapter or other provisions of the authority of Administrator, contained in any (1) legislation proposed by any Federal department or agency, (2) newly authorized Federal projects for construction and any major Federal agency action (other than a project for construction) to which section 4332(2)(C) of this title applies, and (3) proposed regulations published by any department or agency of the Federal Government. Such written comment shall be made public at the conclusion of any such review. Clean Air Act, Section 309 More Documents & Publications

297

Oxidative Mineralization and Characterization of Polyvinyl Alcohol Solutions for Wastewater Treatment  

SciTech Connect

The principal objectives of this study are to identify an appropriate polyvinyl alcohol (PVA) oxidative mineralization technique, perform compatibility and evaporation fate tests for neat and mineralized PVA, and determine potential for PVA chemical interferences which may affect ion exchange utilization for radioactive wastewater processing in the nuclear industry.

Oji, L.N.

1999-08-31T23:59:59.000Z

298

Synthesis of higher alcohols from carbon monoxide and hydrogen in a slurry reactor  

DOE Green Energy (OSTI)

Higher, i.e. C{sub 2{sup +}}, alcohols are desired as gasoline additives, feedstocks for producing ethers and as alternative fuels for automobiles. In all cases, the backbone branching of an alcohol improves octane rating, which is essential for good engine performance. These types of branched, higher alcohols are the desired products for a process converting synthesis gas, a CO and H{sub 2} mixture, often generated from coal gasification. Based on this premise, promoted ZnCr oxide catalysts appear to be as one of the best avenues for further investigation. Once this investigation is complete, a natural extension is to replace the Cr in the ZnCr oxide catalyst with Mo and W, both in the same elemental triad with Cr. Mo has already been shown as an active HAS catalyst, both on a SiO{sub 2} support and in the MoS{sub 2} form. The three catalyst combinations, ZnMo, ZnW, and MnCr oxides will be tested in the stirred autoclave system. However, if none of the three indicate any comparable activity and/or selectivity toward higher alcohols as compared with other HAS catalysts, then an investigation of the effects of Cs promotion on the ZnCr oxide methanol catalysts will be executed.

McCutchen, M.S.

1992-08-28T23:59:59.000Z

299

Lightweight methods to estimate influenza rates and alcohol sales volume from Twitter messages  

Science Conference Proceedings (OSTI)

We analyze over 570 million Twitter messages from an eight month period and find that tracking a small number of keywords allows us to estimate influenza rates and alcohol sales volume with high accuracy. We validate our approach against government statistics ... Keywords: Classification, Regression, Social media

Aron Culotta

2013-03-01T23:59:59.000Z

300

Plasma Semicarbazide-Sensitive Amine Oxidase Activity in Type I and II Alcoholics  

E-Print Network (OSTI)

Semicarbazide-sensitive amine oxidase (SSAO) which catalysis the deamination of primary amines is involved in vascular endothelial or tissue damage through the formation of reactive aldehydes, hydrogen peroxide and ammonia from endogenous substrates. In the present study, plasma SSAO activity, plasma and erythrocyte lipid peroxidation status, glutathione levels and the correlation between the plasma SSAO activity and lipid peroxidation were determined to clarify the mechanism of liver injury related to the oxidative stress in early- and late-onset (Type I and II) alcoholic subtypes. Plasma SSAO activity and, plasma and erythrocyte malondialdehyde (MDA) levels as the indicators of lipid peroxidation status of alcoholics were found to be significantly higher than those of the control group. Increased plasma SSAO activity was strongly correlated with the elevated plasma and erythrocyte MDA levels and decreased reduced/oxidized glutathione (GSH/GSSG) ratio in alcoholics suggesting that enhanced plasma SSAO activity might contribute to the production of reactive oxygen species (ROS) detected in the liver of the alcoholics.

Glberk Uar; Ba?aran Demir; Yaz??ma Adresi

2003-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "alcohol msds section" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


301

Review of Section XI inservice inspection program effectiveness  

Science Conference Proceedings (OSTI)

To evaluate the effectiveness of Section XI, Division 1, {open_quotes}Rules for Inservice Inspection of Nuclear Power Plant Components,{close_quotes} of the American Society of Mechanical Engineers Boiler and Pressure Vessel Code, searches were performed of the Licensing Event Report and Nuclear Plant Reliability Data System computerized data bases, and a review was made of inservice inspection summary reports. It was found that the Section XI examinations and tests detect flaws in welds and plant components and result in subsequent corrective action. This study also shows that the format and topics of information provided in Section XI-prescribed inservice inspection summary reports vary widely.

Cook, J.F. Sr.

1993-08-01T23:59:59.000Z

302

GRR/Section 11 - Cultural Resource Assessment | Open Energy Information  

Open Energy Info (EERE)

- Cultural Resource Assessment - Cultural Resource Assessment < GRR Jump to: navigation, search GRR-logo.png GEOTHERMAL REGULATORY ROADMAP Roadmap Home Roadmap Help List of Sections Section 11 - Cultural Resource Assessment 11CulturalResourceAssessment (1).pdf Click to View Fullscreen Contact Agencies Advisory Council on Historic Preservation National Park Service Bureau of Land Management United States Department of Interior Bureau of Indian Affairs Regulations & Policies National Historic Preservation Act (NHPA) - specifically, Section 106 36 CFR 800 - Protection of Historic Properties Native American Graves Protection Act Archaeological and Historic Preservation Act Archaeological Resource Protection Act American Indian Religious Freedom Act Paleontological Resources Preservation Act Federal Cave Resources Protection Act

303

Commissioning of the cryogenics of the LHC long straight sections  

Science Conference Proceedings (OSTI)

The LHC is made of eight circular arcs interspaced with eight Long Straight Sections (LSS). Most powering interfaces to the LHC are located in these sections where the particle beams are focused and shaped for collision, cleaning and acceleration. The LSSs are constituted of several unique cryogenic devices and systems like electrical feed-boxes, standalone superconducting magnets, superconducting links, RF cavities and final focusing superconducting magnets. This paper presents the cryogenic commissioning and the main results obtained during the first operation of the LHC Long Straight Sections.

Perin, A.; Casas-Cubillos, J.; Claudet, S.; /CERN; Darve, C.; /Fermilab; Ferlin, G.; Millet, F.; Parente, C.; /CERN; Rabehl, R.; /Fermilab; Soubiran, M.; van Weelderen, R.; Wagner, U.; /CERN

2010-01-01T23:59:59.000Z

304

Cross Section to Multiplicity Ratios at Very High Energy  

E-Print Network (OSTI)

Recent data from the LHC makes it possible to examine an old speculation that at very high energy the total multiplicity and the cross section in elementary particle interactions vary in parallel with energy. Using fits incorporating the new data, it appears that the ratios of the total, elastic, and inelastic cross sections to the average multiplicity N can in fact approach constants at very high energy. The approach to the limit is however quite slow for the total and inelastic cross sections and is not yet reached at LHC energies. The elastic ratio sigma^{el}/N at 7 TeV, however, is not far from its asymptotic value.

M. M. Block; L. Stodolsky

2013-12-09T23:59:59.000Z

305

EPAct 2005 Section 1817 Public Comments | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

EPAct 2005 Section 1817 Public Comments EPAct 2005 Section 1817 Public Comments EPAct 2005 Section 1817 Public Comments Following are all comments received by the U.S. Department of Energy on the February 2007 draft of the Study, "The Potential Benefits of Distributed Generation and Rate-Related Issued That May Impede Their Expansion." All comments are provided in their original, unedited format. EPAct 2005 Section 1817 Public Comments More Documents & Publications The Potential Benefits of Distributed Generation and the Rate-Related Issues That May Impede Its Expansion The potential benefits of distributed deneration and rate-related issues that may impede issues its expansion. June 2007 STUDY OF THE EFFECT OF PRIVATE WIRE LAWS ON DEVELOPMENT OF COMBINED HEAT AND POWER FACILITIE

306

GRR/Section 16 - Geological Resources Assessment Process | Open Energy  

Open Energy Info (EERE)

GRR/Section 16 - Geological Resources Assessment Process GRR/Section 16 - Geological Resources Assessment Process < GRR Jump to: navigation, search GRR-logo.png GEOTHERMAL REGULATORY ROADMAP Roadmap Home Roadmap Help List of Sections Section 16 - Geological Resources Assessment Process 16GeologicalResourceAssessmentProcess.pdf Click to View Fullscreen Contact Agencies Bureau of Land Management Regulations & Policies Paleontological Resources Preservation Act 43 CFR 8365.1-5: Public Property and Resources 43 CFR 3620: Petrified Wood 16 USC 4301: Federal Cave Resources Protection Act 43 CFR 1610.7-2: Areas of Critical Environmental Concern Federal Land Policy and Management Act of 1976 Triggers None specified Click "Edit With Form" above to add content 16GeologicalResourceAssessmentProcess.pdf Error creating thumbnail: Page number not in range.

307

GRR/Section 5 - Drilling Overview | Open Energy Information  

Open Energy Info (EERE)

GRR/Section 5 - Drilling Overview GRR/Section 5 - Drilling Overview < GRR Jump to: navigation, search GRR-logo.png GEOTHERMAL REGULATORY ROADMAP Roadmap Home Roadmap Help List of Sections Section 5 - Drilling Overview 05DrillingPermittingOverview.pdf Click to View Fullscreen Contact Agencies BLM Regulations & Policies 30 USC § 1001 Triggers None specified On top of acquiring the correct drilling permits a developer needs to consider issues such as land and mineral ownership and right of way access. 05DrillingPermittingOverview.pdf Error creating thumbnail: Page number not in range. Error creating thumbnail: Page number not in range. Error creating thumbnail: Page number not in range. Flowchart Narrative 5.1 - Review Potential Construction Permits In addition to drilling permits, the developer may require other

308

Section 28 Trust Wind Farm | Open Energy Information  

Open Energy Info (EERE)

Section 28 Trust Wind Farm Section 28 Trust Wind Farm Jump to: navigation, search Name Section 28 Trust Wind Farm Facility Section 28 Trust Sector Wind energy Facility Type Commercial Scale Wind Facility Status In Service Energy Purchaser Southern California Edison Co Location San Gorgonio CA Coordinates 33.9095°, -116.734° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":33.9095,"lon":-116.734,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

309

Microsoft Word - Canceled -7 Section B April 16 2010.doc  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

REFERENCES REFERENCES DEPARTMENT OF ENERGY Office of Security and Safety Performance Assurance DOE M 470.4-7 DOE M 470.4-7 Section B 08-26-05 B-2 SECTION B - SAFEGUARDS AND SECURITY REFERENCES This Section contains S&S references arranged as general references and by topical S&S programmatic areas. These references are currently used in S&S directives. As with the Glossary, revisions to this Section are encouraged and should be submitted to the Office of Security. Safeguards and Security General References 1. United States Code (U.S.C.). a. 5 U.S.C. 552, The Freedom of Information Act, as amended, which requires Federal agencies to make information available upon request by anyone, subject to certain exemptions and exceptions.

310

Microsoft Word - 2007 Australasian Section_ Dec 2007_final.doc  

Science Conference Proceedings (OSTI)

Australasian Section, American Oil Chemist Society December 2007, Newsletter From the President Another busy year nears its end as the festive season approaches and we ready ourselves for family celebrations. This is the second newsletter of

311

RFQ (radio-frequency quadrupole) acceleration section and its optimization  

SciTech Connect

The acceleration section is a crucial component of any radio- frequency quadrupole (RFQ). It is common a practice to design this section with a constant modulation factor equal to its value at the end of the gentle buncher. A new method of design is proposed in this paper. The algorithm is based on the fact that the transverse space-charge current limit (TCL) is approximately proportional to the instantaneous velocity of the accelerated particle and the longitudinal space-charge current limit (LCL) is nearly independent of the velocity in the acceleration section. The modulation factor is increased such that the TCL is slightly larger than the double of the design current. Simulation using this method shows that transmission efficiency and emittances are the same as the conventional design. The advantage gained is a 50-75% increase in accelerating rate. The optimization of the length of this section is also discussed. 3 refs., 4 figs., 1 tab.

Raparia, D.

1988-01-01T23:59:59.000Z

312

Handbook of LHC Higgs Cross Sections: 2. Differential Distributions  

E-Print Network (OSTI)

This Report summarises the results of the second year's activities of the LHC Higgs Cross Section Working Group. The main goal of the working group was to present the state of the art of Higgs Physics at the LHC, integrating all new results that have appeared in the last few years. The first working group report Handbook of LHC Higgs Cross Sections: 1. Inclusive Observables (CERN-2011-002) focuses on predictions (central values and errors) for total Higgs production cross sections and Higgs branching ratios in the Standard Model and its minimal supersymmetric extension, covering also related issues such as Monte Carlo generators, parton distribution functions, and pseudo-observables. This second Report represents the next natural step towards realistic predictions upon providing results on cross sections with benchmark cuts, differential distributions, details of specific decay channels, and further recent developments.

LHC Higgs Cross Section Working Group; S. Dittmaier; C. Mariotti; G. Passarino; R. Tanaka; S. Alekhin; J. Alwall; E. A. Bagnaschi; A. Banfi; J. Blumlein; S. Bolognesi; N. Chanon; T. Cheng; L. Cieri; A. M. Cooper-Sarkar; M. Cutajar; S. Dawson; G. Davies; N. De Filippis; G. Degrassi; A. Denner; D. D'Enterria; S. Diglio; B. Di Micco; R. Di Nardo; R. K. Ellis; A. Farilla; S. Farrington; M. Felcini; G. Ferrera; M. Flechl; D. de Florian; S. Forte; S. Ganjour; M. V. Garzelli; S. Gascon-Shotkin; S. Glazov; S. Goria; M. Grazzini; J. -Ph. Guillet; C. Hackstein; K. Hamilton; R. Harlander; M. Hauru; S. Heinemeyer; S. Hoche; J. Huston; C. Jackson; P. Jimenez-Delgado; M. D. Jorgensen; M. Kado; S. Kallweit; A. Kardos; N. Kauer; H. Kim; M. Kovac; M. Kramer; F. Krauss; C. -M. Kuo; S. Lehti; Q. Li; N. Lorenzo; F. Maltoni; B. Mellado; S. O. Moch; A. Muck; M. Muhlleitner; P. Nadolsky; P. Nason; C. Neu; A. Nikitenko; C. Oleari; J. Olsen; S. Palmer; S. Paganis; C. G. Papadopoulos; T . C. Petersen; F. Petriello; F. Petrucci; G. Piacquadio; E. Pilon; C. T. Potter; J. Price; I. Puljak; W. Quayle; V. Radescu; D. Rebuzzi; L. Reina; J. Rojo; D. Rosco; G. P. Salam; A. Sapronov; J. Schaarschmidt; M. Schonherr; M. Schumacher; F. Siegert; P. Slavich; M. Spira; I. W. Stewart; W. J. Stirling; F. Stockli; C. Sturm; F. J. Tackmann; R. S. Thorne; D. Tommasini; P. Torrielli; F. Tramontano; Z. Trocsanyi; M. Ubiali; S. Uccirati; M. Vazquez Acosta; T. Vickey; A. Vicini; W. J. Waalewijn; D. Wackeroth; M. Warsinsky; M. Weber; M. Wiesemann; G. Weiglein; J. Yu; G. Zanderighi

2012-01-15T23:59:59.000Z

313

Microsoft Word - 2009 Australasian Section_ April 2009_final.doc  

Science Conference Proceedings (OSTI)

Australasian Section, American Oil Chemist Society April 2009, Newsletter In this issue: From the President Industry Updates ? Monola 77T: Nuseeds High Yielding Specialty Canola ? Certified Sustainable Palm Oil Available ? Oilseed Indu

314

References, Canceled -7 Section B - April 16 2010 | Department...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

areas. These references are currently used in S&S directives. As with the Glossary, revisions to this Section are encouraged and should be submitted to the Office of...

315

Geothermal Sourcebook, Section 2.0 - Plant Control (Draft)  

DOE Green Energy (OSTI)

This Section discusses (1) requirements for control of an individual power plant for both base loaded or load following plants, (2) operations during upset conditions, and (3) the degree of automation which may be applicable to a geothermal power plant.

None

1978-04-10T23:59:59.000Z

316

Black Hole Cross Section at the Large Hadron Collider  

E-Print Network (OSTI)

Black hole production at the Large Hadron Collider (LHC) was first discussed in 1999. Since then, much work has been performed in predicting the black hole cross section. In light of the start up of the LHC, it is now timely to review the state of these calculations. We review the uncertainties in estimating the black hole cross section in higher dimensions. One would like to make this estimate as precise as possible since the predicted values, or lower limits, obtain for the fundamental Planck scale and number of extra dimensions from experiments will depend directly on the accuracy of the cross section. Based on the current knowledge of the cross section, we give a range of lower limits on the fundamental Planck scale that could be obtained at LHC energies.

Douglas M. Gingrich

2006-09-06T23:59:59.000Z

317

Energy dependence of the total photoproduction cross section at HERA  

E-Print Network (OSTI)

The energy dependence of the total photon-proton cross-section is determined from data collected with the ZEUS detector at HERA with two different proton beam energies.

Aharon Levy

2008-07-01T23:59:59.000Z

318

Scaling Cross Sections for Ion-atom Impact Ionization  

DOE Green Energy (OSTI)

The values of ion-atom ionization cross sections are frequently needed for many applications that utilize the propagation of fast ions through matter. When experimental data and theoretical calculations are not available, approximate formulas are frequently used. This paper briefly summarizes the most important theoretical results and approaches to cross section calculations in order to place the discussion in historical perspective and offer a concise introduction to the topic. Based on experimental data and theoretical predictions, a new fit for ionization cross sections is proposed. The range of validity and accuracy of several frequently used approximations (classical trajectory, the Born approximation, and so forth) are discussed using, as examples, the ionization cross sections of hydrogen and helium atoms by various fully stripped ions.

Igor D. Kaganovich; Edward Startsev; Ronald C. Davidson

2003-06-06T23:59:59.000Z

319

Microsoft Word - AOCS Australasian Section_ May 2008_finalv2.docm  

Science Conference Proceedings (OSTI)

Australasian Section, American Oil Chemist Society May 2008, Newsletter In this issue: From the President Industry Updates ? Heritability Estimates of Individual Fatty Acids in Merino Meat Reported ? Olive Oil Helps Bypass Patients ? Th

320

Public Comment re Section 934 of the Energy Independence and...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

of 2007 Public Comment by the Uranium Producers of America (UPA) re Section 934 of the Energy Independence and Security Act of 2007 (EISA). The UPA urges DOE to clarify the...

Note: This page contains sample records for the topic "alcohol msds section" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


321

Hadronic cross sections, elastic slope and physical bounds  

Science Conference Proceedings (OSTI)

An almost model-independent parametrization for the ratio of the total hadronic cross section to elastic slope is discussed. Its applicability in studies of asymptotia and analyses of extensive air shower in cosmic-ray physics is also outlined.

Fagundes, D. A.; Menon, M. J. [Instituto de Fisica Gleb Wataghin, Universidade Estadual de Campinas, UNICAMP, 13083-859 Campinas SP (Brazil)

2013-03-25T23:59:59.000Z

322

STATE ADMINISTRATIVE MANUAL SECTIONS 0760-0765 EXPIRES: ISSUING AGENCY:  

E-Print Network (OSTI)

Policy The purpose of this Management Memo is for state agencies to comply with outof-state travel requirements of Section 11032 of the Government Code and Sections 0760 0765 of the State Administrative Manual. Government Code Section 11032 requires prior approval of out-of-state travel expenses by the Director of Finance and the Governors Office. State Administrative Manual (SAM) Section 0764 requires departments to submit out of state travel requests to the Department of Finance (Finance) at least 14 days before the travel is scheduled to begin. Failure to submit travel requests within this timeframe may result in the denial of the request by Finance. In addition, claims submitted to the State Controllers Office for reimbursement for out-of-state travel costs are subject to audit by the State Controllers Office and the payment will be denied if the claim is not in compliance with the statutory and administrative guidelines. Non-Compliance

Michael C. Genest

2004-01-01T23:59:59.000Z

323

GRR/Section 8 - Transmission Overview | Open Energy Information  

Open Energy Info (EERE)

GRR/Section 8 - Transmission Overview GRR/Section 8 - Transmission Overview < GRR Jump to: navigation, search GRR-logo.png GEOTHERMAL REGULATORY ROADMAP Roadmap Home Roadmap Help List of Sections Section 8 - Transmission Overview 08 - TransmissionOverview.pdf Click to View Fullscreen Contact Agencies Federal Energy Regulatory Commission Regulations & Policies FERC Order No. 2003 FERC Order No. 2006 Triggers None specified Click "Edit With Form" above to add content 08 - TransmissionOverview.pdf 08 - TransmissionOverview.pdf Error creating thumbnail: Page number not in range. Error creating thumbnail: Page number not in range. Flowchart Narrative The siting of an individual project can have a major impact on transmission and interconnection. 8.1 - Will the Power Plant Developer Negotiate an Interconnection

324

GRR/Section 9 - Environmental Overview | Open Energy Information  

Open Energy Info (EERE)

GRR/Section 9 - Environmental Overview GRR/Section 9 - Environmental Overview < GRR Jump to: navigation, search GRR-logo.png GEOTHERMAL REGULATORY ROADMAP Roadmap Home Roadmap Help List of Sections Section 9 - Environmental Overview 09EnvironmentalOverview.pdf Click to View Fullscreen Contact Agencies United States Environmental Protection Agency BLM United States Forest Service DOE United States Department of Defense Regulations & Policies National Environmental Policy Act 40 CFR 1508.18 Major Federal Action Triggers None specified Click "Edit With Form" above to add content 09EnvironmentalOverview.pdf Error creating thumbnail: Page number not in range. Error creating thumbnail: Page number not in range. Error creating thumbnail: Page number not in range. Flowchart Narrative The National Environmental Policy Act (NEPA) was signed into law on January

325

Prosection views: Dimensional inference through sections and projections  

E-Print Network (OSTI)

We present some basic properties of two general graphical techniques for constructing views of high-dimensional objects, projection and section. Projections can easily display aspects of structure that are only of low dimension, while sections, i.e., intersections of subspaces with a highdimensional object, can easily display structure of only low codimension (and hence often high dimension). However, compositions of sections and projections, here called prosections, can display aspects of structure of any intermediate dimension. These statements are relevant for data analysis: projections of data can be easily generated with x-yscatterplots, 3-D data rotations, and grand tours, while sections can be approximated in existing systems by scatterplot brushing and painting. Thus this paper is in part an investigation into the principles underlying these techniques.

George W. Furnas; Andreas Buja

1994-01-01T23:59:59.000Z

326

Foothills Parkway Section 8B Final Environmental Report, Volume 1  

SciTech Connect

In 1994, Oak Ridge National Laboratory (ORNL) was tasked by the National Park Service (NPS) to prepare an Environmental Report (ER) for Section 8B of the Foothills Parkway in the Great Smoky Mountains National Park (GSMNP). Section 8B represents 27.7 km (14.2 miles) of a total of 115 km (72 miles) of the planned Foothills Parkway and would connect the Cosby community on the east to the incorporated town of Pittman Center to the west.

Blasing, T.J.; Cada, G.F.; Carer, M.; Chin, S.M.; Dickerman, J.A.; Etnier, D.A.; Gibson, R.; Harvey, M.; Hatcher, B.; Lietzske, D.; Mann, L.K.; Mulholland, P.J.; Petrich, C.H.; Pounds, L.; Ranney, J.; Reed, R.M.; Ryan, P.F.; Schweitzer, M.; Smith, D.; Thomason, P.; Wade, M.C.

1999-07-01T23:59:59.000Z

327

Photon - Axion Conversion Cross Sections in a Resonant Cavity  

E-Print Network (OSTI)

Photon - axion conversions in the resonant cavity with the lowest mode are considered in detail by the Feynman diagram method. The differential cross sections are presented and numerical evaluations are given. It is shown that there is a resonant conversion for the considered process, in which the conversion cross sections are much larger than those of the wave guide in the same conditions. Some estimates for experimental conditions are given from our results.

Dang Van Soa; Hoang Ngoc Long; Le Nhu Thuc

2006-11-20T23:59:59.000Z

328

Cross section space shielding in double heterogeneous HTGR systems  

SciTech Connect

Collision probability methods using rational approximations for space shielding of cross sections in nuclear reactor codes allowing for one level of heterogeneity are first reviewed. A Dancoff factor for a cylindrical HTGR fuel pin with grain structure is then derived. A new simple method for cross section space shielding in a doubly heterogeneous HTGR system using collision probabilities and rational approximations is subsequently presented and calculations based on it are compared with calculations based on more elaborate methods. 39 references. (auth)

Stamatelatos, M.G.

1975-11-01T23:59:59.000Z

329

ADVANCED HOT SECTION MATERIALS AND COATINGS TEST RIG  

SciTech Connect

The Hyperbaric Advanced Hot Section Materials & Coating Test Rig program initiated this quarter, provides design and implementation of a laboratory rig capable of simulating the hot gas path conditions of coal-gas fired industrial gas turbine engines. The principle activity during this first reporting period were preparing for and conducting a project kick-off meeting, working through plans for the project implementation, and beginning the conceptual design of the test section.

Scott Reome; Dan Davies

2004-01-01T23:59:59.000Z

330

Radial Eigenmodes for a Toroidal Waveguide with Rectangular Cross Section  

SciTech Connect

In applying mode expansion to solve the CSR impedance for a section of toroidal vacuum chamber with rectangular cross section, we identify the eigenvalue problem for the radial eigenmodes which is different from that for cylindrical structures. In this paper, we present the general expressions of the radial eigenmodes, and discuss the properties of the eigenvalues on the basis of the Sturm-Liouville theory.

Rui Li

2012-07-01T23:59:59.000Z

331

New aspects in the evaluation of thermal neutron cross sections  

Science Conference Proceedings (OSTI)

Because of recent advances in experimental techniques, which improved the accuracies of thermal capture and scattering cross sections by an order of magnitude, a more stringent approach in the evaluation of the thermal constants is developed. In the present approach, the following aspects are introduced: (1) a consistency between thermal cross sections, coherent and incoherent scattering lengths, and neutron resonance parameters is achieved; (2) a consistency between the isotopic and element cross sections is sought; in addition, for each isotope, the requirement that the partial cross sections add up to the total is fulfilled; (3) where possible, charged particle data particularly derived from (d,p) reactions on light and medium weight isotopes are used in locating the positions and strengths of bound levels. Such a procedure is useful in the evaluation of the shape of the cross sections in the thermal region; and (4) the Lane-Lynn theory of direct capture is called upon to calculate thermal cross sections and check for consistencies for certain isotopes. Extensive examples to illustrate these procedures are presented.

Mughabghab, S.F.

1980-01-01T23:59:59.000Z

332

Effect of incorporating cellulose nanocrystals from corncob on the tensile, thermal and barrier properties of poly(vinyl alcohol) nanocomposites  

Science Conference Proceedings (OSTI)

The effect of incorporating cellulose nanocrystals fromcorncob (CNC) on the tensile, thermal, and barrier properties of poly(vinyl alcohol) (PVA) nanocomposites was evaluated. The CNC were prepared by sulfuric acid hydrolysis at 45C for 60 minutes, ...

Hudson Alves Silvrio, Wilson Pires Flauzino Neto, Daniel Pasquini

2013-01-01T23:59:59.000Z

333

Dual bowl metering block for alcohol and/or nitro-methane burning carburetor and method of conversion  

Science Conference Proceedings (OSTI)

An improved carburetor metering block for converting a conventional gasoline carburetor to alcohol fuel involving a carburetor metering block means adapted to attach to a conventional carburetor and replace the removable fuel bowl and standard metering block wherein the improved carburetor metering block means is adapted to accept, simultaneously, a plurality of individual and separate fuel bowls. Such a device can inexpensively convert a conventional carburetor to the use of alcohol fuel consistent with sufficient fuel flow and adequate fuel level control.

Horton, J.A.

1984-02-07T23:59:59.000Z

334

Thermochemical Ethanol via Direct Gasification and Mixed Alcohol Synthesis of Lignocellulosic Biomass  

NLE Websites -- All DOE Office Websites (Extended Search)

Thermochemical Ethanol via Thermochemical Ethanol via Direct Gasification and Mixed Alcohol Synthesis of Lignocellulosic Biomass A. Dutta and S.D. Phillips Technical Report NREL/TP-510-45913 July 2009 Technical Report Thermochemical Ethanol via NREL/TP-510-45913 Direct Gasification and Mixed July 2009 Alcohol Synthesis of Lignocellulosic Biomass A. Dutta and S.D. Phillips Prepared under Task No. BB07.3710 National Renewable Energy Laboratory 1617 Cole Boulevard, Golden, Colorado 80401-3393 303-275-3000 * www.nrel.gov NREL is a national laboratory of the U.S. Department of Energy Office of Energy Efficiency and Renewable Energy Operated by the Alliance for Sustainable Energy, LLC Contract No. DE-AC36-08-GO28308 NOTICE This report was prepared as an account of work sponsored by an agency of the United States government.

335

Fabrication of silicon field emission tips for vacuum microelectronics by KOH/Alcohol/Water etching  

Science Conference Proceedings (OSTI)

The fabrication of sharp silicon tips for field emission cathodes by KOH/Alcohol/Water (KAW) solution was investigated. The KOH/Alcohol/Water solution was found to work better and easier than the Ethylene-Diamine/Pyrocathechol/Water solution in etching silicon tips. It etched the (100) silicon surface more slowly, but in a more controllable manor. The resulting tips were usually very uniform and pretty sharp in most studies. Actually, there were some systems showing non-uniform etching behavior. However, we were able to demonstrate that the uniformity could be improved by shifting the reaction from mass transfer controlled to chemical kinetics controlled. Such technique could allow us to fabricate uniform silicon cones even in a very primitive apparatus with non-uniform mass transfer. 5 refs., 7 figs.

Hui, W.C.; Hee, E.; Ciarlo, D.

1990-11-01T23:59:59.000Z

336

Short-chain polymer rigidity due to the Debye process of monohydroxy alcohols  

E-Print Network (OSTI)

In addition to the ubiquitous structural relaxation of viscous supercooled liquids, monohydroxy alcohols and several other hydrogen-bonded systems display a strong single-exponential electrical low-frequency absorption. So far, this so-called Debye process could be observed only using dielectric techniques. Exploiting a combination of broad-band and high-resolution rheology experiments for three isomeric octanols, unambiguous mechanical evidence for the Debye process is found. Its spectral signature is similar to the viscoelastic fingerprint of small-chain polymers, enabling us to estimate the effective molecular weight for the supramolecular structure formed by the studied monohydroxy alcohols. This finding opens the venue for the application of further non-dielectric techniques directed at unraveling the microscopic nature of the Debye process and for an understanding of this phenomenon in terms of polymer concepts.

C. Gainaru; R. Figuli; T. Hecksher; B. Jakobsen; J. C. Dyre; M. Wilhelm; R. Bhmer

2013-05-19T23:59:59.000Z

337

Optimization of Rhodium-Based Catalysts for Mixed Alcohol Synthesis -- 2009 Progress Report  

DOE Green Energy (OSTI)

Pacific Northwest National Laboratory (PNNL) has been conducting research for the United States Department of Energy, Energy Efficiency Renewable Energy, Biomass Program to investigate the feasibility of producing mixed alcohols from biomass-derived synthesis gas (syngas). This research has involved the screening of potential catalysts, and optimization of the more promising ones, using laboratory scale reactors. During 2009, the main goal of the testing program focused on optimizing selected supported catalysts containing rhodium (Rh) and manganese (Mn). Optimization involved examining different total concentrations and atomic ratios of Rh and Mn as well as that of the more promising promoters (Ir and Li) identified in the earlier screening studies. Evaluation of catalyst performance focused on attaining improvements with respect to the space-time-yield and converted carbon selectivity to C2+ oxygenates, with additional consideration given to the fraction of the oxygenates that were C2+ alcohols.

Gerber, Mark A.; Gray, Michel J.; Stevens, Don J.; White, J. F.; Rummel, Becky L.

2010-12-21T23:59:59.000Z

338

Technoeconomic Analysis of a Lignocellulosic Biomass Indirect Gasification Process to Make Ethanol via Mixed Alcohols Synthesis  

Science Conference Proceedings (OSTI)

A technoeconomic analysis of a 2000 tonne/day lignocellulosic biomass conversion process to make mixed alcohols via gasification and catalytic synthesis was completed. The process, modeled using ASPEN Plus process modeling software for mass and energy calculations, included all major process steps to convert biomass into liquid fuels, including gasification, gas cleanup and conditioning, synthesis conversion to mixed alcohols, and product separation. The gas cleanup area features a catalytic fluidized-bed steam reformer to convert tars and hydrocarbons into syngas. Conversions for both the reformer and the synthesis catalysts were based on research targets expected to be achieved by 2012 through ongoing research. The mass and energy calculations were used to estimate capital and operating costs that were used in a discounted cash flow rate of return analysis for the process to calculate a minimum ethanol selling price of $0.267/L ($1.01/gal) ethanol (U.S.$2005).

Phillips, S. D.

2007-01-01T23:59:59.000Z

339

Film Thickness Changes in EHD Sliding Contacts Lubricated by a Fatty Alcohol  

E-Print Network (OSTI)

This paper describes the appearance of abnormal film thickness features formed in elastohydrodynamic contacts lubricated by a fatty alcohol. Experiments were conducted by varying the slide to roll ratio between a steel ball and a glass disk in a ball-on-disk type device. Lauric alcohol was used as lubricant and film thickness was measured in the contact area by optical interferometry. Experimental results showed that the film thickness distributions under pure rolling conditions remained classical whereas the film shape changed when the slide to roll ratio was increased. The thickness in the central contact area increased and in the same time inlet and exit film thicknesses were modified. In addition, the film shapes observed when the ball surface was moving faster than the disk one and those obtained in the opposite case were different, i.e. when opposite signs but equal absolute values of the slide to roll ratio were applied.

Yagi, Kazuyuki

2006-01-01T23:59:59.000Z

340

Alternative energy sources for non-highway transportation: technical section  

DOE Green Energy (OSTI)

Eighteen different alternative fuels were considered in the preliminary screening, from three basic resource bases. Coal can be used to provide 13 of the fuels; oil shale was the source for three of the fuels; and biomass provided the resource base for two fuels not provided from coal. In the case of biomass, six different fuels were considered. Nuclear power and direct solar radiation were also considered. The eight prime movers that were considered in the preliminary screening are boiler/steam turbine; open and closed cycle gas turbines; low and medium speed diesels; spark ignited and stratified charge Otto cycles; electric motor; Stirling engine; free piston; and fuel cell/electric motor. Modes of transport considered are pipeline, marine, railroad, and aircraft. Section 2 gives the overall summary and conclusions, the future outlook for each mode of transportation, and the R and D suggestions by mode of transportation. Section 3 covers the preliminary screening phase and includes a summary of the data base used. Section 4 presents the methodology used to select the fuels and prime movers for the detailed study. Sections 5 through 8 cover the detailed evaluation of the pipeline, marine, railroad, and aircraft modes of transportation. Section 9 covers the demand related issues.

Not Available

1980-06-01T23:59:59.000Z

Note: This page contains sample records for the topic "alcohol msds section" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


341

Education outreach programs at the Eastern Washington Section  

SciTech Connect

The Eastern Washington Section of the American Nuclear Society (ANS) has tried a number of different approaches to reach out to the local communities and to work alongside educators to increase their awareness of nuclear technology. Some of the programs that the authors have started may serve as examples for other sections in their outreach activities. The Eastern Washington Section of the ANS has an education committee coordinator who is assigned the task of working with high school and college students to increase the awareness of nuclear energy. The most effective approach that the authors have found to reach out to the area schools is to get directly involved with community activities that already interface with the schools and get to know the science teachers at the local schools. The Hanford project has a student internship program called ``Inquiry into Science``. The program allows students to work at Hanford for Science credits. Another program that the local section sponsors is grants to high schools to promote the awareness of nuclear technology. The local section has also worked alongside local community groups to increase nuclear science education. For years the authors have been active in the local science fair, providing awards to nuclear-related science projects. Other community events that the ANS has been involved in include the US Department of Energy Knowledge Bowl and National Engineers.

Schwarz, R.A. [Battelle, Richland, WA (United States)

1998-09-01T23:59:59.000Z

342

Correlation between speciated hydrocarbon emissions and flame ionization detector response for gasoline/alcohol blends .  

DOE Green Energy (OSTI)

The U.S. renewable fuel standard has made it a requirement to increase the production of ethanol and advanced biofuels to 36 billion by 2022. Ethanol will be capped at 15 billion, which leaves 21 billion to come from other sources such as butanol. Butanol has a higher energy density and lower affinity for water than ethanol. Moreover, alcohol fueled engines in general have been shown to positively affect engine-out emissions of oxides of nitrogen and carbon monoxide compared with their gasoline fueled counterparts. In light of these developments, the variety and blend levels of oxygenated constituents is likely to increase in the foreseeable future. The effect on engine-out emissions for total hydrocarbons is less clear due to the relative insensitivity of the flame ionization detector (FID) toward alcohols and aldehydes. It is well documented that hydrocarbon (HC) measurement using a conventional FID in the presence of oxygenates in the engine exhaust stream can lead to a misinterpretation of HC emissions trends for alcohol fuel blends. Characterization of the exhaust stream for all expected hydrocarbon constituents is required to accurately determine the actual concentration of unburned fuel components in the exhaust. In addition to a conventional exhaust emissions bench, this characterization requires supplementary instrumentation capable of hydrocarbon speciation and response factor independent quantification. Although required for certification testing, this sort of instrumentation is not yet widely available in engine development facilities. Therefore, an attempt is made to empirically determine FID correction factors for oxygenate fuels. Exhaust emissions of an engine fueled with several blends of gasoline and ethanol, n-butanol and iso-Butanol were characterized using both a conventional FID and a Fourier transform infrared. Based on these results, a response factor predicting the actual hydrocarbon emissions based solely on FID results as a function of alcohol type and content is presented. Finally, the correlation derived from data presented in this study is compared with equations and results found in the literature.

Wallner, T. (Energy Systems)

2011-08-01T23:59:59.000Z

343

Hydrogenolysis Of 5-Carbon Sugars, Sugar Alcohols And Compositions For Reactions Involving Hydrogen  

DOE Patents (OSTI)

Methods and compositions for reactions of hydrogen over a Re-containing catalyst with compositions containing a 5-carbon sugar, sugar alcohol, or lactic acid are described. It has been surprisingly discovered that reaction with hydrogen over a Re-containing multimetallic catalyst resulted in superior conversion and selectivity to desired products such as propylene glycol. A process for the synthesis of PG from lactate or lactic acid is also described.

Werpy, Todd A. (West Richland, WA); Frye, Jr., John G. (Richland, WA); Zacher, Alan H. (Kennewick, WA); Miller, Dennis J. (Okemos, MI)

2004-01-13T23:59:59.000Z

344

Nuclear magnetic resonance measurements reveal the origin of the Debye process in monohydroxy alcohols  

E-Print Network (OSTI)

Monohydroxy alcohols show a structural relaxation and at longer time scales a Debye-type dielectric peak. From spin-lattice relaxation experiments using different nuclear probes an intermediate, slower-than-structural dynamics is identified for n-butanol. Based on these findings and on diffusion measurements, a model of self-restructuring, transient chains is proposed. The model is demonstrated to explain consistently the so far puzzling observations made for this class of hydrogen-bonded glass forming liquids.

C. Gainaru; R. Meier; S. Schildmann; C. Lederle; W. Hiller; E. A. Rssler; R. Bhmer

2010-08-19T23:59:59.000Z

345

Spectroscopic Analyses of the Biofuels-Critical Phytochemical Coniferyl Alcohol and Its Enzyme-Catalyzed Oxidation Products  

SciTech Connect

Lignin composition (monolignol types of coniferyl, sinapyl or p-coumaryl alcohol) is causally related to biomass recalcitrance. We describe multiwavelength (220, 228, 240, 250, 260, 290, 295, 300, 310 or 320 nm) absorption spectroscopy of coniferyl alcohol and its laccase- or peroxidase-catalyzed products during real time kinetic, pseudo-kinetic and endpoint analyses, in optical turn on or turn off modes, under acidic or basic conditions. Reactions in microwell plates and 100 mu L volumes demonstrated assay miniaturization and high throughput screening capabilities. Bathochromic and hypsochromic shifts along with hyperchromicity or hypochromicity accompanied enzymatic oxidations by laccase or peroxidase. The limits of detection and quantitation of coniferyl alcohol averaged 2.4 and 7.1 mu M respectively, with linear trend lines over 3 to 4 orders of magnitude. Coniferyl alcohol oxidation was evident within 10 minutes or with 0.01 mu g/mL laccase and 2 minutes or 0.001 mu g/mL peroxidase. Detection limit improved to 1.0 mu M coniferyl alcohol with Km of 978.7 +/- 150.7 mu M when examined at 260 nm following 30 minutes oxidation with 1.0 mu g/mL laccase. Our assays utilized the intrinsic spectroscopic properties of coniferyl alcohol or its oxidation products for enabling detection, without requiring chemical synthesis or modification of the substrate or product(s). These studies facilitate lignin compositional analyses and augment pretreatment strategies for reducing biomass recalcitrance.

Achyuthan, Komandoor; Adams, Paul; Simmons, Blake; Singh, Anup

2011-07-13T23:59:59.000Z

346

Economic and energetic evaluation of alcohol fuel production from agriculture: Yolo County, California  

SciTech Connect

This dissertation reviews the technical aspects of alcohol fuel production and consumption, examines the set of policy-related issues that affect both the private and the public sectors, and investigates the economic and energetic feasibility of small-scale on-farm production on a representative Sacramento Valley field and vegetable crop farm. Candidate feedstocks, including both starch and sugar-rich crops, are: barley, corn, fodder beet, grain sorghum, Jerusalem artichoke, sugar beet, sweet sorghum, tomatoes, and wheat. The leading fuel crops were found to be sweet sorghum, Jerusalem artichoke, corn, fodder beet, and grain sorghum in order of declining preference. With better than average crop yields and the current mix of financial incentives, the breakeven cost of alcohol fuel is $1.03 per gallon when diesel fuel and gasoline prices are $1.30 and $1.46, respectively. Without subsidy, the breakeven cost is $1.62 per gallon. An energy analysis was calculated for each of the feedstocks under consideration. With the exception of sweet sorghum, wheat, and barley, all feedstocks showed a negative net energy balance. The use of agricultural residues as a boiler fuel, however, made a significant difference in the overall energy balance. The role of government in energy policy is reviewed and typical policy instruments are discussed. Although on-farm alcohol fuel production is not currently economically competitive with gasoline and diesel fuel, technological innovation and the return of increasing petroleum prices could alter the situation.

Meo, M.

1983-01-01T23:59:59.000Z

347

Method and system for producing lower alcohols. [Heteropolyatomic lead salt coated with alkali metal formate  

DOE Patents (OSTI)

It is an object of the present invention to provide an improved catalyst for the reaction of carbon monoxide with water to produce methanol and other lower alcohols. It is a further object to provide a process for the production of methanol from carbon monoxide and water in which a relatively inexpensive catalyst permits the reaction at low pressures. It is also an object to provide a process for the production of methanol from carbon monoxide and water in which a relatively inexpensive catalyst permits the reaction at low pressures. It is also an object to provide a process for the production of methanol in which ethanol is also directly produced. It is another object to provide a process for the production of mixtures of methanol with ethanol and propanol from the reaction of carbon monoxide and water at moderate pressure with inexpensive catalysts. It is likewise an object to provide a system for the catalytic production of lower alcohols from the reaction of carbon monoxide and water at moderate pressure with inexpensive catalysts. In accordance with the present invention, a catalyst is provided for the reaction of carbon monoxide and water to produce lower alcohols. The catalyst includes a lead heteropolyatomic salt in mixture with a metal formate or a precursor to a metal formate.

Rathke, J.W.; Klingler, R.J.; Heiberger, J.J.

1983-09-26T23:59:59.000Z

348

Federal Power Act section 202(c) - Mirant Corporation, August 2005 |  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Federal Power Act section 202(c) - Mirant Corporation, August 2005 Federal Power Act section 202(c) - Mirant Corporation, August 2005 Federal Power Act section 202(c) - Mirant Corporation, August 2005 On August 24, 2005 in response to a decision by Mirant Corporation to cease generation of electricity at its Potomac River generating station, the District of Columbia Public Service Commission requested that the Secretary of Energy issue a 202(c) emergency order requiring the operation of the Potomac River generating station in order to ensure compliance with reliability standards for the central D.C. area. After investigation, the Secretary made a determination that without the operation of the Potomac River generating station there was a reasonable possibility an outage would occur that would cause a blackout in the central D.C. area. Therefore, on

349

Recent advances in modeling fission cross sections over intermediate structures  

SciTech Connect

More accurate fission cross section calculations in presence of underlying intermediate structure are strongly desired. This paper recalls the common approximations used below the fission threshold and quantifies their impact. In particular, an exact expanded R-matrix Monte Carlo calculation of the intermediate structure, deeply mixed with the fluctuations of the class-I and II decay amplitudes, is shown. This paper also insists on the microscopic structure of the level densities as a function of the nucleus deformation and show preliminary neutron induced fission cross section calculations for {sup 239}Pu and {sup 240}Pu using newly calculated combinatorial level densities. Comparisons with recent evaluated and measured fission cross sections are made.

Bouland, Olivier [Los Alamos National Laboratory; Lynn, J. Eric [Los Alamos National Laboratory; Talou, Patrick [Los Alamos National Laboratory

2009-01-01T23:59:59.000Z

350

GRR/Section 1 - Land Use Overview | Open Energy Information  

Open Energy Info (EERE)

1 - Land Use Overview 1 - Land Use Overview < GRR Jump to: navigation, search GRR-logo.png GEOTHERMAL REGULATORY ROADMAP Roadmap Home Roadmap Help List of Sections Section 1 - Land Use Overview 01LandUseOverview.pdf Click to View Fullscreen Contact Agencies Bureau of Land Management U S Army Corps of Engineers United States Environmental Protection Agency Fish and Wildlife Service United States Department of Defense Regulations & Policies Federal Land Policy and Management Act of 1976 Endangered Species Act Clean Water Act Clean Air Act Farmland Protection Policy Act Sikes Act National Historic Preservation Act (NHPA) - specifically, Section 106 Native American Graves Protection Act Archaeological Resource Protection Act Triggers None specified Click "Edit With Form" above to add content

351

DOE_PPPL_Section G_M007  

NLE Websites -- All DOE Office Websites (Extended Search)

G G M007 i PART I SECTION G CONTRACT ADMINISTRATION DATA TABLE OF CONTENTS PAGE NO. G.1 - DOE CONTRACTING OFFICER G-1 G.2 - DOE CONTRACTING OFFICER'S REPRESENTATIVE (COR) G-1 G.3 - CONTRACT ADMINISTRATION G-1 G.4 - REPORTING PROCEDURES G-2 G.5 - INDIRECT CHARGES G-2 Contract No. DE-AC02-09CH11466 Section G M007 G-1 PART I SECTION G - CONTRACT ADMINISTRATION DATA G.1 - DOE CONTRACTING OFFICER For the definition of Contracting Officer see Federal Acquisition Regulation (FAR) 2.101. The Contracting Officer is the only individual who has the authority on behalf of DOE to take the following actions under the contract: (1) assign additional work within the general scope of the Statement of Work of the contract; (2) issue a change as defined in the "Changes" clause of the contract;

352

Category:Geothermal Regulatory Roadmap Sections | Open Energy Information  

Open Energy Info (EERE)

source source History View New Pages Recent Changes All Special Pages Semantic Search/Querying Get Involved Help Apps Datasets Community Login | Sign Up Search Category Edit History Facebook icon Twitter icon » Category:Geothermal Regulatory Roadmap Sections Jump to: navigation, search GRR-logo.png Looking for the Geothermal Regulatory Roadmap? Click here for a user-friendly list of Geothermal Regulatory Roadmap pages. Add.png Add a Section Pages in this category are created or edited using the RRSection form. Subcategories This category has the following 2 subcategories, out of 2 total. R [×] Regulatory Roadmap Overview Sections‎ 22 pages [×] Regulatory Roadmap State Sections‎ 362 pages Pages in category "Geothermal Regulatory Roadmap Sections" The following 200 pages are in this category, out of 432 total. (previous

353

pi+- p differential cross sections at low energies  

Science Conference Proceedings (OSTI)

Differential cross sections for pi- p and pi+ p elastic scattering were measured at five energies between 19.9 and 43.3 MeV. The use of the CHAOS magnetic spectrometer at TRIUMF, supplemented by a range telescope for muon background suppression, provided simultaneous coverage of a large part of the full angular range, thus allowing very precise relative cross section measurements. The absolute normalization was determined with a typical accuracy of 5 %. This was verified in a simultaneous measurement of muon proton elastic scattering. The measured cross sections show some deviations from phase shift analysis predictions, in particular at large angles and low energies. From the new data we determine the real part of the isospin forward scattering amplitude.

H. Denz; P. Amaudruz; J.T. Brack; J. Breitschopf; P. Camerini; J.L. Clark; H. Clement; L. Felawka; E. Fragiacomo; E.F. Gibson; N. Grion; G.J. Hofman; B. Jamieson; E.L. Mathie; R. Meier; G. Moloney; D. Ottewell; O. Patarakin; J.D. Patterson; M.M. Pavan; S. Piano; K. Raywood; R.A. Ristinen; R. Rui; M.E. Sevior; G.R. Smith; J. Stahov; R. Tacik; G.J. Wagner; F. von Wrochem; D.M. Yeomans

2005-12-03T23:59:59.000Z

354

Inelastic cross sections for positron scattering from atomic hydrogen  

DOE Green Energy (OSTI)

Positronium formation (Ps) cross sections for positrons impinging on atomic hydrogen were measured in the impact energy range from 13eV to 255eV at the High Intensity Positron (HIP) beam at Brookhaven National Laboratory (BNL). The Ps-formation cross section was found to rise rapidly from the threshold at 6.8eV to a maximum value of (2.98 {plus_minus} 0.18) {times} 10{sup {minus}16} cm{sup 2} for {approx} 15eV positrons. By 75eV it drops below the detection limit of 0.17 {times} 10{sup {minus}16} cm{sup 2} which is the present level of statistical uncertainty. The experiment was modified to enable the measurement of doubly differential scattering cross sections.

Weber, M.; Hofmann, A.; Raith, W.; Sperber, W. [Bielefeld Univ. (Germany). Fakultaet fuer Physik; Jacobsen, F.; Lynn, K.G. [Brookhaven National Lab., Upton, NY (United States)

1994-12-31T23:59:59.000Z

355

Advanced Hot Section Materials and Coatings Test Rig  

DOE Green Energy (OSTI)

Phase I of the Hyperbaric Advanced Hot Section Materials & Coating Test Rig Program has been successfully completed. Florida Turbine Technologies has designed and planned the implementation of a laboratory rig capable of simulating the hot gas path conditions of coal gas fired industrial gas turbine engines. Potential uses of this rig include investigations into environmental attack of turbine materials and coatings exposed to syngas, erosion, and thermal-mechanical fatigue. The principle activities during Phase 1 of this project included providing several conceptual designs for the test section, evaluating various syngas-fueled rig combustor concepts, comparing the various test section concepts and then selecting a configuration for detail design. Conceptual definition and requirements of auxiliary systems and facilities were also prepared. Implementation planning also progressed, with schedules prepared and future project milestones defined. The results of these tasks continue to show rig feasibility, both technically and economically.

Dan Davis

2006-09-30T23:59:59.000Z

356

A new method for the calculation of photodissociation cross sections  

SciTech Connect

A time-independent quantum mechanical approach to the calculation of photodissociation cross sections is developed. The method is based on the use of a discrete variable representation (DVR) and the application of absorbing boundary conditions (ABC). Both total photodissociation cross sections and partial cross sections (hence product state distributions) are obtained using the same basic technique, but the calculation is particularly efficient when only the former quantity is required. The method is applied to the photodissociation of HCl[sup +] for which accurate potential energy curves and dipole moment functions are available, to the photodissociation of ClCN which is a direct process, involving a single excited electronic state, and to the photodissociation of ICN which involves several strongly coupled excited electronic states. The applicability of the suggested scheme to a variety of other field--matter interaction processes is pointed out.

Seideman, T. (Department of Chemistry, University of California, Berkeley, California 94720 (United States))

1993-02-01T23:59:59.000Z

357

Bayesian Analysis of Inconsistent Measurements of Neutron Cross Sections  

SciTech Connect

The evaluation of neutron cross sections as a function of energy is fraught with inconsistent measurements. I describe a Bayesian approach to deal with the inconsistencies by probabilistically modeling the possibility of discrepant data and data sets with long-tailed likelihood functions. Systematic normalization uncertainties in each data set are included by considering the normalization to be a variable with specified uncertainty. By characterizing its uncertainty with a mixture of Cauchy and Gaussian distributions, data sets that disagree with the majority of others are given less weight in terms of normalization, but still provide useful information about the energy dependency of the cross sections. I demonstrate the approach with data sets of neutron fission cross sections for americium 243. Samples from the posterior obtained with the Markov Chain Monte Carlo technique are used to estimate the posterior mean and standard error.

Hanson, Kenneth M. [Theoretical Division, Los Alamos National Laboratory, Los Alamos, NM 87545 (United States)

2005-11-23T23:59:59.000Z

358

EIS-0391-FEIS-Volume3-Section4-2012  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

SECTION 4 SECTION 4 REFERENCES 4-1 SECTION 4 REFERENCES Anderson, J.D., 1996, The History of the 200 Area Burial Ground Facilities, WHC-EP-0912, Westinghouse Hanford Company, Richland, Washington, September. Anderson, J.D., and D.L. Hagel, 1996, Summary of Radioactive Solid Waste Received in the 200 Areas During Calendar Year 1995, WHC-EP-0125-8, Westinghouse Hanford Company, Richland, Washington, June. Atkinson, A., and J.A. Hearne, 1984, An Assessment of the Long-Term Durability of Concrete in Radioactive Waste Repositories, AERE-R11465, United Kingdom Atomic Energy Authority, Harwell, England, October. Barnett, D.B., R.M. Smith, C.J. Chou, and J.P. McDonald, 2005, Groundwater Monitoring Plan for the Hanford Site 216-B-3 Pond RCRA Facility, PNNL-15479, Pacific Northwest National Laboratory, Richland,

359

SODIUM GRAPHITE REACTOR QUARTERLY PROGRESS REPORT FOR OCTOBER-DECEMBER 1955. SECTION A. SECTION B  

DOE Green Energy (OSTI)

An analysis was made of the nuclear parameters for sodium graphite reactor lattices. These parameters include thermal utilization, macroscopic cross sections, thermal diffusion length, and neutron absorption. Results of all calculations are given in graphical form. Test fuel slugs for the SRE were cycled up to 500 times between 100 and 500 deg C at the rate of 2 cycles/hr. Results are tabulated. The centrifugal casting of U alloy fuel slugs is briefly evaluated. Results of the microscopic examination of the extruded ThU breeder fuels are shown. The percent elongation of graphite due to the presence of Na is shown for various temperatures. Results of wear tests on graphite are also tabulated. The behavior of Zr in liquid Na was studied, and weight gains in Zr are summarized. Analog computer studies were continued, and data are included on the temperature effects of the response time of coolant channel Na outlet temperature thermocouples, the effects of continuous rod motion and pump speed changes on the outlet Na temperature and power, and the outlet temperature as a function of scram time. The critical evaluation of B--Ni rods is tabulated. The fuel rod assembly apparatus is described. Fuel rod development is discussed. Cyclograph traces of rods bonded with various Na--K alloys were recorded for rods at room temperature and heated to 450 and 600 deg F. The traces are indicative of uniform bonding. The moderator can fabrication and testing is also discussed. Tests were completed on Freeze Seal No. 2 for the 6-in. oval port Wedgeplug test valve at 450, 850, and 1250 deg F. The temperature gradients from the hot flange face to the end of the seal mechanism for various valve temperature conditions are shown. Sodium leak rates through the valve are tabulated. Progress in the development of a liquid Na level gage is briefly reported. The tubular heater experiment was completed, and the times to raise pipe temperatures from ambient to 350 deg F are tabulated. Designs for a 6-in. Na pump loop are described briefly. A one to 3.5 scale model of a SRE fuel element was constructed to study the effect of side drag on the element during insertion operations at those fuel channels located near the outlet of the upper plenum chamber. The calibration of the SRE fuel element orifices was studied. Control rod lead screw development is discussed. Development of the safety rod system is described. Core tank galling tests are summarized. Experiments to determine the effects of radiation on MoS/ sub 2/ are described. Dose buildup factors for the concretes to be used in the reactor top shield are tabulated. Constants for the quadratic representation of the dose buildup factor and the capture gamma rays from heavy concrete are also tabulated. The sodium pumps and service system are described. The rated cooling capacity of the SRE tetralin evaporative cooler was checked. Results of a study on the effects of NaK temperature on the H content of He are tabulated. (D.E.B.)

Martin, A.B.; Cochran, J.C. ed.

1956-04-15T23:59:59.000Z

360

Interstrand resistance of selected sections of DCA312  

Science Conference Proceedings (OSTI)

The quench current ramp rate sensitivity of the full length SSC dipole DCA312 was strongly A-type and the eddy current losses for this magnet were the largest of all ASST magnets. The quench current remained constant with ramp rate up to approximately 20 A/s. At higher ramp rates the quench current decreased dramatically. At a current ramp rate of 200 A/s the quench current was only 2000 A. The eddy current losses of DCA312 at 60 A/s for a monopolar cycle of 500A-5000A-500A were approximately 3600 J/Cycle, a factor of 5--7 larger than for magnets DCA311, DCA319, and DCA318. In order to find the cause of the anomalous behavior of DCA312, it was decided that the magnet would be cut into sections and examined at WMSD and SSCL. The general goals of the DCA312 autopsy included verification of theoretical models for A-type behavior in SSC magnets as well as correlation of fabrication and assembly procedures to the quench behavior of A-type magnets. One of the important aspects of the magnet autopsy plan was the in-situ measurement of interstrand resistance in collared magnet sections. Four sections of DCA312 were designated for interstrand resistance measurements. Two of those sections (C and M) contained quench sites (100 A/s and 200 A/s respectively) and two of them (E and J) were sections representative of the magnet where quenches did not occur. The aim of the present work was to measure and analyze the interstrand resistance in each quadrant of these four sections of DCA312 and to find a correlation between the measured interstrand resistance, the actual resistance of individual interstrand contacts, and the quench performance of the magnet.

Kovachev, V.; Neal, M.; Seuntjens, J.; Qin, J.; Cline, P.; Capone, D. II [Superconducting Super Collider Lab., Dallas, TX (United States); Swenson, C. [Westinghouse Electric Corp., Round Rock, TX (United States)

1993-11-01T23:59:59.000Z

Note: This page contains sample records for the topic "alcohol msds section" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


361

DE-AC05-06OR23100 Section H  

NLE Websites -- All DOE Office Websites (Extended Search)

DE-AC05-06OR23100 DE-AC05-06OR23100 Section H - Page 1 of 29 PART I - SCHEDULE SECTION H SPECIAL CONTRACT REQUIREMENTS H.1 CONSECUTIVE NUMBERING (MAY 1997)......................................................................... 4 H.2 MODIFICATION AUTHORITY (MAY 1997) ....................................................................... 4 H.3 OVERSIGHT OF CONTRACTOR (OCT 2004)..................................................................... 4 H.4 SMALL BUSINESS SUBCONTRACTING PLAN (SEPT 1999)............................................ 5 H.5 SAFEGUARDS AND SECURITY AWARENESS PROGRAM (MAY 1997)........................ 5 H.6 QUALITY ASSURANCE SYSTEM ALTERNATE I (JUL 2004).......................................... 5 H.7 CONFIDENTIALITY OF INFORMATION (MAY 1997)...................................................... 6 H.8 INDIRECT

362

Inelastic cross sections from gamma-ray measurements  

Science Conference Proceedings (OSTI)

Measurements of gamma rays following neutron induced reactions have been studied with the Germanium Array for Neutron-induced Excitations (GEANIE) at the Los Alamos Neutron Science Center (LANSCE) for many years. Gamma-ray excitation functions and coincidence studies provide insight into nuclear reaction mechanisms as well as expanding our knowledge of energy levels and gamma-rays. Samples studied with Ge detectors at LANSCE range from Be to Pu. Fe, Cr and Ti have been considered for use as reference cross sections. An overview of the measurements and efforts to create a reliable neutron-induced gamma-ray reference cross section will be presented.

Nelson, Ronald Owen [Los Alamos National Laboratory

2010-12-06T23:59:59.000Z

363

Microsoft Word - Canceled -7 Section C April 16 2010.doc  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

ACRONYMS & ACRONYMS & ABBREVIATIONS DEPARTMENT OF ENERGY Office of Security and Safety Performance Assurance DOE M 470.4-7 DOE M 470.4-7 Section C 08-26-05 C-2 SECTION C - ACRONYMS AND ABBREVIATIONS 3-D Three Dimensional A AAAP Accelerated Access Authorization Program AC Advisory Circular ACL Adversary Capability List AIP Aviation Implementation Plan AIS Automated Information System ANACI Access National Agency Check and Inquiries ANSI American National Standards Institute ARAPT Alarm Response and Assessment Performance Test ARG Accident Response Group ASTM ASTM International (formerly "American Society for Testing Materials") AWE Atomic Weapons Establishment B BCD Binary Code Decimal BD Blast Deflector

364

Bent solenoids for spectrometers and emittance exchange sections.  

Science Conference Proceedings (OSTI)

Bent solenoids can be used to transport low energy beams as they provide both confinement and dispersion of particle orbits. Solenoids are being considered both as emittance exchange sections and spectrometers in the muon cooling system as part of the study of the muon collider. They present the results of a study of bent solenoids which considers the design of coupling sections between bent solenoids to straight solenoids, drift compensation fields, aberrations, and factors relating to the construction, such as field ripple, stored energy, coil forces and field errors.

Norem, J.

1999-03-26T23:59:59.000Z

365

Sub-barrier Fusion Cross Sections with Energy Density Formalism  

E-Print Network (OSTI)

We discuss the applicability of the energy density formalism (EDF) for heavy-ion fusion reactions at sub-barrier energies. For this purpose, we calculate the fusion excitation function and the fusion barrier distribution for the reactions of $^{16}$O with $^{154,}$$^{144}$Sm,$^{186}$W and $^{208}$Pb with the coupled-channels method. We also discuss the effect of saturation property on the fusion cross section for the reaction between two $^{64}$Ni nuclei, in connection to the so called steep fall-off phenomenon of fusion cross sections at deep sub-barrier energies.

F. Muhammad Zamrun; K. Hagino; N. Takigawa

2006-06-07T23:59:59.000Z

366

Suppressed fusion cross section for neutron halo nuclei  

E-Print Network (OSTI)

Fusion reactions of neutron-halo nuclei are investigated theoretically with a three-body model. The time-dependent wave-packet method is used to solve the three-body Schrodinger equation. The halo neutron behaves as a spectator during the Coulomb dissociation process of the projectile. The fusion cross sections of 11Be-209Bi and 6He-238U are calculated and are compared with measurements. Our calculation indicates that the fusion cross section is slightly hindered by the presence of weakly bound neutrons.

Makoto Ito; Kazuhiro Yabana; Takashi Nakatsukasa; Manabu Ueda

2005-06-23T23:59:59.000Z

367

Hadronic absorption cross sections of B{sub c}  

Science Conference Proceedings (OSTI)

The cross sections of B{sub c} absorption by {pi} mesons are calculated using a hadronic Lagrangian based on the SU(5) flavor symmetry. Calculated cross sections are found to be in the ranges 2-7 mb and 0.2-2 mb for the processes B{sub c}{sup +}{pi}{yields}DB and B{sub c}{sup +}{pi}{yields}D*B*, respectively, when the monopole form factor is included. These results could be useful in calculating the production rate of B{sub c} mesons in relativistic heavy ion collisions.

Lodhi, M. A. K. [Department of Physics, MS 1051, Texas Tech University, Lubbock, Texas 79409 (United States); Akram, Faisal; Irfan, Shaheen [Center for High Energy Physics, Punjab University, Lahore (Pakistan)

2011-09-15T23:59:59.000Z

368

New neutron cross section and fission yield data for SNManalysis  

DOE Green Energy (OSTI)

Neutron cross-section data are fundamental for the design ofnuclear interrogation systems, the maintenance of nuclear materials andwaste, and the understanding the consequences of nuclear catastrophe.Although a large body of nuclear data exists, it is often old,unreliable, or poorly determined. For several years we have collaborated,as part of an IAEA Coordinated Research Project, to precisely measure thepartial thermal neutron gamma ray cross sections for all elements fromhydrogen to uranium at the Budapest Reactor. These data will replace theunreliable tables of Lone et al [1], still widely in use, and will bepublished as an IAEA TECDOC.

Firestone, R.B.; Molnar, G.L.; Revay, Zs.; Belgya, T.

2003-05-28T23:59:59.000Z

369

Australasian Section of the American Oil Chemists' Society (AAOCS) Biennial Conference  

Science Conference Proceedings (OSTI)

Archive of the Australasian Section of the American Oil Chemists' Society (AAOCS)Biennial Conference Australasian Section of the American Oil Chemists' Society (AAOCS) Biennial Conference Adelaide, Australia Australasian Section of the American O

370

GRR/Section 1-CA-a - State Land Use Planning | Open Energy Information  

Open Energy Info (EERE)

Section 1-CA-a - State Land Use Planning < GRR Jump to: navigation, search GRR-logo.png GEOTHERMAL REGULATORY ROADMAP Roadmap Home Roadmap Help List of Sections Section 1-CA-a -...

371

NUMBER: FCMN 2.15 SECTION: Business and Finance  

E-Print Network (OSTI)

for generating, distributing and maintaining the high pressure steam (for heating and hot water) and chilledNUMBER: FCMN 2.15 SECTION: Business and Finance SUBJECT: Campus Utilities and Energy Distribution water (for air conditioning)distribution systems. In addition, Energy Services personnel maintain all

Almor, Amit

372

Microsoft Word - KCP Section J Appendix N - List of Applicable...  

National Nuclear Security Administration (NNSA)

NFPA 1600 (Sections 5.1 thru 5.7, 6.1 thru 6.11, 7.1 thru 7.5, 8.1 & 8.2) Standard for Disaster Emergency Management, 2010 Edition NFPA 704 Standard System for the...

373

Automatic segmentation of histological structures in mammary gland tissue sections  

SciTech Connect

Real-time three-dimensional (3D) reconstruction of epithelial structures in human mammary gland tissue blocks mapped with selected markers would be an extremely helpful tool for breast cancer diagnosis and treatment planning. Besides its clear clinical application, this tool could also shed a great deal of light on the molecular basis of breast cancer initiation and progression. In this paper we present a framework for real-time segmentation of epithelial structures in two-dimensional (2D) images of sections of normal and neoplastic mammary gland tissue blocks. Complete 3D rendering of the tissue can then be done by surface rendering of the structures detected in consecutive sections of the blocks. Paraffin embedded or frozen tissue blocks are first sliced, and sections are stained with Hematoxylin and Eosin. The sections are then imaged using conventional bright field microscopy and their background is corrected using a phantom image. We then use the Fast-Marching algorithm to roughly extract the contours of the different morphological structures in the images. The result is then refined with the Level-Set method which converges to an accurate (sub-pixel) solution for the segmentation problem. Finally, our system stacks together the 2D results obtained in order to reconstruct a 3D representation of the entire tissue block under study. Our method is illustrated with results from the segmentation of human and mouse mammary gland tissue samples.

Fernandez-Gonzalez, Rodrigo; Deschamps, Thomas; Idica, Adam K.; Malladi, Ravikanth; Ortiz de Solorzano, Carlos

2004-02-17T23:59:59.000Z

374

PROGRESS WITH NSLS-II INJECTION STRAIGHT SECTION DESIGN  

SciTech Connect

The NSLS-II injection straight section (SR) consists of pulsed and DC bumps, septa system, beam trajectory correction and diagnostics systems. In this paper we discuss overall injection straight layout, preliminary element designs, specifications for the pulsed and DC magnets and their power supplies, vacuum devices and chambers and diagnostics devices. Prior to selecting the current 'conventional' design of the injection straight section we analyzed an option of injection via pulsed multipole pioneered at PF-AR. We found that this promising approach was not suited to the NSLS-II storage ring optics, since it would require a impractically compact arrangement of the injection straight section components and a complex modification of the transport line optics due to the strong focusing of the injected beam passing off the pulsed multipole axis. In addition, the requirement for a small injection transient of the stored beam orbit severely constrains the vertical alignment tolerance of the pulsed multipole. The design of the NSLS-II injection straight section is now completed with exception of transition chamber details, which will be adjusted to accommodate the actual layouts of the pulsed magnets.

Shaftan, T.; Blednykh, A.; Casey, B.; Dalesio, B.; Faussete, R.; Ferreira, M.; Fliller, R.; Ganetis, G.; Heese, R.; Hseuh, H.-C.; Job, P.K.; Johnson, E.; Kosciuk, B.; Kowalski, S.; Padrazo, D.; Parker, B.; Pinayev, I.; Sharma, S.; Singh, O.; Spataro, C.

2011-03-28T23:59:59.000Z

375

Clean Water Act Section 316(a): Past, Present, and Future  

Science Conference Proceedings (OSTI)

Thermal discharge issues are receiving increasing attention from government agencies and electric power companies. This report summarizes the status and future trends regarding thermal discharge research and regulations with respect to Section 316(a) of the Clean Water Act (CWA). The report will be of particular value to power company environmental staff, government regulators and water resource managers.

2009-01-16T23:59:59.000Z

376

RZ calculations for self shielded multigroup cross sections  

Science Conference Proceedings (OSTI)

A collision probability method has been implemented for RZ geometries. The method accounts for white albedo, specular and translation boundary condition on the top and bottom surfaces of the geometry and for a white albedo condition on the outer radial surface. We have applied the RZ CP method to the calculation of multigroup self shielded cross sections for Gadolinia absorbers in BWRs. (authors)

Li, M.; Sanchez, R.; Zmijarevic, I.; Stankovski, Z. [Commissariat a l'Energie Atomique CEA, Direction de l'Energie Nucleaire, DEN/DM2S/SERMA/LENR, 91191 Gif-sur-Yvette Cedex (France)

2006-07-01T23:59:59.000Z

377

Oceanic Fluxes on the WOCE A11 Section  

Science Conference Proceedings (OSTI)

The most southerly WOCE one-time section in the South Atlantic, designated A11, was occupied in January 1993. The cruise track lay across the cool subantarctic zone of the Circumpolar Current in the west and the warm subtropical gyre in the east. ...

Peter M. Saunders; Brian A. King

1995-09-01T23:59:59.000Z

378

NUMBER: BUSF 4.12 SECTION: Finance and Planning  

E-Print Network (OSTI)

by an unusually large number of other persons opening accounts or by other Customers. 16. The person opening1 NUMBER: BUSF 4.12 SECTION: Finance and Planning SUBJECT: University Identity Theft and Detection of the account. 3. "Customer" means a person that has a Covered Account with the University. 4. "Identity Theft

Almor, Amit

379

Norm continuous unitary representations of Lie algebras of smooth sections  

E-Print Network (OSTI)

We give a complete description of the bounded (i.e. norm continuous) unitary representations of the Fr\\'echet-Lie algebra of all smooth sections, as well as of the LF-Lie algebra of compactly supported smooth sections, of a smooth Lie algebra bundle whose typical fiber is a compact Lie algebra. For the Lie algebra of all sections, bounded unitary irreducible representations are finite tensor products of so-called evaluation representations, hence in particular finite-dimensional. For the Lie algebra of compactly supported sections, bounded unitary irreducible (factor) representations are possibly infinite tensor products of evaluation representations, which reduces the classification problem to results of Glimm and Powers on irreducible (factor) representations of UHF C*-algebras. The key part in our proof is the classification of irreducible bounded unitary representations of Lie algebras that are the tensor product of a compact Lie algebra and a unital real continuous inverse algebra: every such representation is a finite product of evaluation representations. On the group level, our results cover in particular the bounded unitary representations of the identity component of the group of smooth gauge transformations of a principal fiber bundle with compact base and structure group, and the connected component of the group of special unitary n times n matrices with values in an involutive commutative continuous inverse algebra.

Bas Janssens; Karl-Hermann Neeb

2013-02-11T23:59:59.000Z

380

Ionizationexcitation magnetic sublevel cross sections states following fast electron  

E-Print Network (OSTI)

Center for Astrophysics, Cambridge, MA 02138, USA Abstract The first experimental magnetic substate S ground state to the final ionic state Heþ (2p) 2 P0 (also noted as HeII(2p) 2 P0 ) in e? þ He single that these absolute total cross sections do not provide direct information about the magnetic substate populations

Godunov, Alexander L.

Note: This page contains sample records for the topic "alcohol msds section" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


381

Inclusive Cross Sections in ME+PS Merging  

E-Print Network (OSTI)

We discuss an extension of matrix element plus parton shower merging at leading and next-to-leading order. The algorithm does preserve inclusive cross sections at the respective input order. This constraint avoids potentially large logarithmic contributions, which would require approximate (N)NLO contributions to cancel against.

Pltzer, Simon

2013-01-01T23:59:59.000Z

382

Inclusive Cross Sections in ME+PS Merging  

E-Print Network (OSTI)

We discuss an extension of matrix element plus parton shower merging at leading and next-to-leading order. The algorithm does preserve inclusive cross sections at the respective input order. This constraint avoids potentially large logarithmic contributions, which would require approximate (N)NLO contributions to cancel against.

Simon Pltzer

2013-07-02T23:59:59.000Z

383

Absolute photoionization cross-section of the propargyl radical  

SciTech Connect

Using synchrotron-generated vacuum-ultraviolet radiation and multiplexed time-resolved photoionization mass spectrometry we have measured the absolute photoionization cross-section for the propargyl (C{sub 3}H{sub 3}) radical, {sigma}{sub propargyl}{sup ion}(E), relative to the known absolute cross-section of the methyl (CH{sub 3}) radical. We generated a stoichiometric 1:1 ratio of C{sub 3}H{sub 3} : CH{sub 3} from 193 nm photolysis of two different C{sub 4}H{sub 6} isomers (1-butyne and 1,3-butadiene). Photolysis of 1-butyne yielded values of {sigma}{sub propargyl}{sup ion}(10.213 eV)=(26.1{+-}4.2) Mb and {sigma}{sub propargyl}{sup ion}(10.413 eV)=(23.4{+-}3.2) Mb, whereas photolysis of 1,3-butadiene yielded values of {sigma}{sub propargyl}{sup ion}(10.213 eV)=(23.6{+-}3.6) Mb and {sigma}{sub propargyl}{sup ion}(10.413 eV)=(25.1{+-}3.5) Mb. These measurements place our relative photoionization cross-section spectrum for propargyl on an absolute scale between 8.6 and 10.5 eV. The cross-section derived from our results is approximately a factor of three larger than previous determinations.

Savee, John D.; Welz, Oliver; Taatjes, Craig A.; Osborn, David L. [Sandia National Laboratories, Combustion Research Facility, Livermore, California 94551 (United States); Soorkia, Satchin [Institut des Sciences Moleculaires d'Orsay, Universite Paris-Sud 11, Orsay (France); Selby, Talitha M. [Department of Chemistry, University of Wisconsin, Washington County Campus, West Bend, Wisconsin 53095 (United States)

2012-04-07T23:59:59.000Z

384

LLNL-TR-446331 ENDF Cross Sections are not  

E-Print Network (OSTI)

LLNL-TR-446331 ENDF Cross Sections are not Uniquely Defined by Dermott E. Cullen Lawrence Livermore Technical Information Department's Digital Library http://www.llnl.gov/tid/Library.html #12;1 LLNL-TR-446331/NEA Data Bank), Pavel Oblozinsky (BNL, Retired), Ernest Plechaty (LLNL, retired), Andrej Trkov (IJS). Last

Cullen, Red

385

Arbitrary blade section design based on viscous considerations. Background information  

SciTech Connect

Background information is presented on an arbitrary blade section design method which is outlined in a joint paper. This information concerns the assumptions, the development, and the predictive capabilities of the viscous flow calculation tool used in the design procedure. General properties of laminar and turbulent, unseparated or separated compressible shear layers, necessary for the blade optimization procedure, are discussed.

Bouras, B.; Karagiannis, F.; Leoutsakos, G.; Giannakoglou, K.C.; Papailiou, K.D. [National Technical Univ. of Athens (Greece). Thermal Turbomachinery Lab.

1996-06-01T23:59:59.000Z

386

Two Cross-Equatorial Sections at 110W  

Science Conference Proceedings (OSTI)

A section along 110W in the eastern Pacific from about 6N to 6S was occupied in March and June of 1981. Measurements consisted of absolute velocity profiles and CTD cuts. The large-scale structure of the subsurface zonal flow remained ...

Ants Leetmaa; Robert L. Molinari

1984-02-01T23:59:59.000Z

387

ENERGY DRINK CONSUMPTION (WITH AND WITHOUT ALCOHOL) AND ITS RELATIONSHIP TO RISKY BEHAVIOR, RISK AWARENESS, AND BEHAVIORAL INTENTION IN COLLEGE STUDENTS.  

E-Print Network (OSTI)

??The purpose of this study was to assess the relationships between energy drink consumption (with and without alcohol) and other risky behaviors; students overall awareness (more)

Buchanan, Julia K

2012-01-01T23:59:59.000Z

388

Federal Power Act section 202(c) - California, December 2000 | Department  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

California, December 2000 California, December 2000 Federal Power Act section 202(c) - California, December 2000 On December 14, 2000, a Federal Power Act section 202(c) emergency order was issued in response to the California energy crisis. The order was directed to the California Independent System Operator (CAISO) and a group of electricity generators that supplied the CAISO. The order required the generators, upon a finding by the CAISO that, on any given day, it was "unable to acquire in the market adequate supplies of electricity to meet system demand", to provide electricity to the CAISO on that day. The expiration date on that order was December 21, 2000, but it was extended until January 11, 2001. Due to the expiration of the December 14, 2000 order, a new order with the same terms was issued on January 11, 2001. The

389

GRR/Section 6 - Construction Permits Overview | Open Energy Information  

Open Energy Info (EERE)

6 - Construction Permits Overview 6 - Construction Permits Overview < GRR Jump to: navigation, search GRR-logo.png GEOTHERMAL REGULATORY ROADMAP Roadmap Home Roadmap Help List of Sections Section 6 - Construction Permits Overview 06 - ConstructionPermitsOverview.pdf Click to View Fullscreen Triggers None specified Click "Edit With Form" above to add content 06 - ConstructionPermitsOverview.pdf 06 - ConstructionPermitsOverview.pdf Error creating thumbnail: Page number not in range. Error creating thumbnail: Page number not in range. Flowchart Narrative Constructing a geothermal power plant requires numerous permits from Federal, state, and local governments, related to transporting construction materials, encroaching upon Federal and state right-of-ways, demolishing existing structures and building new structures.

390

GRR/Section 17 - Aesthetic Resource Assessment | Open Energy Information  

Open Energy Info (EERE)

7 - Aesthetic Resource Assessment 7 - Aesthetic Resource Assessment < GRR Jump to: navigation, search GRR-logo.png GEOTHERMAL REGULATORY ROADMAP Roadmap Home Roadmap Help List of Sections Section 17 - Aesthetic Resource Assessment 17 - Aesthetic Resources Overview.pdf Click to View Fullscreen Contact Agencies Bureau of Land Management Regulations & Policies Wild and Scenic Rivers Act Federal Land Policy and Management Act of 1976 National Environmental Policy Act Clean Air Act Triggers None specified Click "Edit With Form" above to add content 17 - Aesthetic Resources Overview.pdf Error creating thumbnail: Page number not in range. Error creating thumbnail: Page number not in range. Error creating thumbnail: Page number not in range. Flowchart Narrative Aesthetic or Visual Resources are often considered during the land use

391

GRR/Section 4 - Exploration Overview | Open Energy Information  

Open Energy Info (EERE)

4 - Exploration Overview 4 - Exploration Overview < GRR Jump to: navigation, search GRR-logo.png GEOTHERMAL REGULATORY ROADMAP Roadmap Home Roadmap Help List of Sections Section 4 - Exploration Overview 04ExplorationPermittingOverview (3).pdf Click to View Fullscreen Contact Agencies BLM United States Forest Service Regulations & Policies 30 USC § 1001 Triggers None specified Click "Edit With Form" above to add content 04ExplorationPermittingOverview (3).pdf Error creating thumbnail: Page number not in range. Error creating thumbnail: Page number not in range. Error creating thumbnail: Page number not in range. Flowchart Narrative The exploration process requires consideration of right of way access, geothermal leasing, and state and federal exploration permits. 4.1 and 4.2 - Will the Developer Engage in Coproduction on an Existing

392

EPA's Section 309 Review: The Clean Air Act and NEPA  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Environmental Protection Agency Environmental Protection Agency Office of Enforcement and Compliance Assurance July, 1999 EPA's Section 309 Review: The Clean Air Act and NEPA Office of Federal Activities (2251A) Quick Reference Brochure ENVIRONMENTAL REVIEW AND THE CLEAN AIR ACT The Clean Air Act, a law to prevent pollution of a single environmental medium, contains an unusual provision. T h a t provision is Section 309, which authorizes the Environmental Protection Agency (EPA) to review certain proposed actions of other federal agencies in accordance with the National Environmental Policy Act (NEPA) and to make those reviews public. If the proposing agency (the "lead" agency) does not make sufficient revisions and the project remains environmentally unsatisfactory. EPA may refer the matter to the President's Council on Environmental Quality for

393

Chevy Chase Section Five, Maryland: Energy Resources | Open Energy  

Open Energy Info (EERE)

Chevy Chase Section Five, Maryland: Energy Resources Chevy Chase Section Five, Maryland: Energy Resources Jump to: navigation, search Equivalent URI DBpedia Coordinates 38.9837213°, -77.0741443° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":38.9837213,"lon":-77.0741443,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

394

Microsoft Word - canceled -7 Section A April 16 2010.doc  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

A A p p r o v e d : 0 8 - 2 6 - 0 5 SAFEGUARDS AND SECURITY PROGRAM GLOSSARY DEPARTMENT OF ENERGY Office of Security and Safety Performance Assurance DOE M 470.4-7 DOE M 470.4-7 Section A 08-26-05 A-2 (and A-2) SECTION A - SAFEGUARDS AND SECURITY GLOSSARY The Safeguards and Security Glossary contains DOE safeguards and security (S&S) program terms and definitions. These terms and their definitions reflect the latest additions and changes to terminology commonly used in S&S programs. Generally used terms defined in most dictionaries have been intentionally omitted from the Glossary. Although a Manual including the Safeguards and Security Glossary would be considered a requirements document, it is not intended that the definitions imply or be construed as

395

Potential Outline of Section 180(c) Policy and Procedures  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

J J Funding Operational Activities I. Introduction Version 22 1 2 4 6 8 10 12 14 16 18 20 22 24 The States believe that the NWPA creates an obligation on Department of Energy to cover all costs related to SNF/HLW transportation, whether the funds flow through Section 180(c) or another funding mechanism. 1 Since Section 180(c) has been interpreted by DOE's Office of General Counsel as applying strictly to "training-related" activities, this issue paper explores other funding mechanisms available to pay for non-training activities. These activities may include inspections, tracking, escorting, public information, and other operational activities related to accident prevention and emergency response.

396

GRR/Section 14 - Water Resource Assessment | Open Energy Information  

Open Energy Info (EERE)

- Water Resource Assessment - Water Resource Assessment < GRR Jump to: navigation, search GRR-logo.png GEOTHERMAL REGULATORY ROADMAP Roadmap Home Roadmap Help List of Sections Section 14 - Water Resource Assessment 14 - WaterResourceAssessment.pdf Click to View Fullscreen Contact Agencies United States Environmental Protection Agency Bureau of Land Management US Army Corps of Engineers Federal Emergency Management Agency Regulations & Policies Clean Water Act Coastal Zone Management Act Coastal Barrier Resources Act Safe Drinking Water Act Sole Source Aquifer Demonstration Program Flood Disaster Protection Act of 1973 NPDES Rules National Flood Insurance Act Flood Disaster Protection Act of 1973 Triggers None specified Click "Edit With Form" above to add content 14 - WaterResourceAssessment.pdf

397

Experimental validation of lead cross sections for scale and MCNP  

SciTech Connect

Moving spent nuclear fuel between facilities often requires the use of lead-shielded casks. Criticality safety that is based upon calculations requires experimental validation of the fuel matrix and lead cross section libraries. A series of critical experiments using a high-enriched uranium-aluminum fuel element with a variety of reflectors, including lead, has been identified. Twenty-one configurations were evaluated in this study. The fuel element was modelled for KENO V.a and MCNP 4a using various cross section sets. The experiments addressed in this report can be used to validate lead-reflected calculations. Factors influencing calculated k{sub eff} which require further study include diameters of styrofoam inserts and homogenization.

Henrikson, D.J.

1995-12-01T23:59:59.000Z

398

Fully hadronic tt cross section with the ATLAS detector  

E-Print Network (OSTI)

A measurement of the tt production cross section in the all-hadronic decay mode is presented using 4.7 fb-1 of proton-proton collisions at a centre of mass energy of 7 TeV collected by the ATLAS experiment in 2011. Events are selected using a multi-jet trigger. Kinematic and b-tagging requirements are then applied to identify tt event candidates. A kinematic fit reconstructs the event topology of the final state extracting the top-quark mass which is then used to measure the production cross section with an unbinned likelihood fit. The result is found in good agreement with the Standard Model prediction for a top-quark mass of 172.5 GeV.

Andrea Coccaro; on behalf of the ATLAS collaboration

2013-02-14T23:59:59.000Z

399

GRR/Section 20 - Plant Decommissioning Overview | Open Energy Information  

Open Energy Info (EERE)

20 - Plant Decommissioning Overview 20 - Plant Decommissioning Overview < GRR Jump to: navigation, search GRR-logo.png GEOTHERMAL REGULATORY ROADMAP Roadmap Home Roadmap Help List of Sections Section 20 - Plant Decommissioning Overview 20PlantDecommissioningOverview (1).pdf Click to View Fullscreen Contact Agencies BLM Regulations & Policies 43 CFR 3263.10-3263.15: Well Abandonment Geothermal Resources Operational Order No.3 Triggers None specified Click "Edit With Form" above to add content 20PlantDecommissioningOverview (1).pdf Error creating thumbnail: Page number not in range. Error creating thumbnail: Page number not in range. Error creating thumbnail: Page number not in range. Flowchart Narrative State and federal laws have specific requirements for the decommissioning process. 20.1 to 20.2 - Will a Geothermal Well be Abandoned?

400

GRR/Section 2 - Preliminary Site Considerations | Open Energy Information  

Open Energy Info (EERE)

2 - Preliminary Site Considerations 2 - Preliminary Site Considerations < GRR Jump to: navigation, search GRR-logo.png GEOTHERMAL REGULATORY ROADMAP Roadmap Home Roadmap Help List of Sections Section 2 - Preliminary Site Considerations 02SiteConsiderations (1).pdf Click to View Fullscreen Contact Agencies United States Forest Service Fish and Wildlife Service Bureau of Land Management Western Governors' Association Regulations & Policies National Environmental Policy Act Triggers None specified Click "Edit With Form" above to add content 02SiteConsiderations (1).pdf Error creating thumbnail: Page number not in range. Error creating thumbnail: Page number not in range. Error creating thumbnail: Page number not in range. Flowchart Narrative Premilinary site selection of geothermal exploration and potential leasing

Note: This page contains sample records for the topic "alcohol msds section" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


401

Hydrogen-bond equilibria and life times in a supercooled monohydroxy alcohol  

E-Print Network (OSTI)

Dielectric loss spectra covering 13 decades in frequency were collected for 2-ethyl-1-hexanol, a monohydroxy alcohol that exhibits a prominent Debye-like relaxation, typical for several classes of hydrogen-bonded liquids. The thermal variation of the dielectric absorption amplitude agrees well with that of the hydrogen-bond equilibrium population, experimentally mapped out using near infrared (NIR) and nuclear magnetic resonance (NMR) measurements. Despite this agreement, temperature-jump NIR spectroscopy reveals that the hydrogen-bond switching rate does not define the frequency position of the prominent absorption peak. This contrasts with widespread notions and models based thereon, but is consistent with a recent approach.

C. Gainaru; S. Kastner; F. Mayr; P. Lunkenheimer; S. Schildmann; H. J. Weber; W. Hiller; A. Loidl; R. Bhmer

2011-06-28T23:59:59.000Z

402

Vehicle-emission characteristics using mechanically emulsified alcohol/diesel fuels  

Science Conference Proceedings (OSTI)

A light-duty diesel vehicle fueled with an emulsified alcohol/diesel fuel was operated under cyclic mode. Emission and fuel economy measurements were taken during vehicle operation. The test results showed the volumetric fuel economy decreased slightly. Carbon monoxide emissions increased slightly, and oxides of nitrogen showed no significant change. Particulate emissions were reduced slightly, and the particulate extractables increased slightly. The environmental effect of these data cancel each other resulting in no significant changes in the total release of biological activity into the environment.

Allsup, J.R.; Seizinger, D.E.; Cox, F.W.; Brook, A.L.; McClellan, R.O.

1983-07-01T23:59:59.000Z

403

ANALYTIC EXPRESSIONS FOR THE LIGHT-SCATTERING CROSS SECTION  

NLE Websites -- All DOE Office Websites (Extended Search)

ANALYTIC ANALYTIC EXPRESSIONS FOR THE LIGHT-SCATTERING CROSS SECTION AND ÅNGSTRÖM EXPONENT OF AN AEROSOL Ernie R. Lewis Brookhaven National Laboratory, Upton, NY 11933 elewis@bnl.gov BACKGROUND For an aerosol consisting of spherical particles with size distribution of number concentration dN(r)/dr and real index of refraction m (thus no absorption), the light-scattering coefficient σ sp

404

Evaluation tests for photovoltaic concentrator receiver sections and modules  

DOE Green Energy (OSTI)

Sandia has developed a third-generation set of specifications for performance and reliability testing of photovoltaic concentrator modules. Several new requirements have been defined. The primary purpose of the tests is to screen new concentrator designs and new production runs for susceptibility to known failure mechanisms. Ultraviolet radiation testing of materials precedes receiver section and module performance and environmental tests. The specifications include the purpose, procedure, and requirements for each test. Recommendations for future improvements are presented.

Woodworth, J.R.; Whipple, M.L.

1992-06-01T23:59:59.000Z

405

Negative ion detachment cross sections. Interim progress report  

DOE Green Energy (OSTI)

The authors have measured absolute cross sections for electron detachment and charge exchange for collision of O and S with atomic hydrogen, have investigated the sputtering and photodesorption of negative ions from gas covered surfaces, and have begun an investigation of photon-induced field emission of electrons from exotic structures. Brief descriptions of these activities as well as future plans for these projects are given below.

Champion, R.L.; Doverspike, L.D.

1992-10-01T23:59:59.000Z

406

Neutrino and Antineutrino Cross sections at MiniBooNE  

SciTech Connect

The MiniBooNE experiment has reported a number of high statistics neutrino and anti-neutrino cross sections -among which are the charged current quasi-elastic (CCQE) and neutral current elastic (NCE) neutrino scattering on mineral oil (CH2). Recently a study of the neutrino contamination of the anti-neutrino beam has concluded and the analysis of the anti-neutrino CCQE and NCE scattering is ongoing.

Dharmapalan, Ranjan; /Alabama U.

2011-10-01T23:59:59.000Z

407

Overview of recent U235 neutron cross section evaluation work  

Science Conference Proceedings (OSTI)

This report is an overview (through 1997) of the U235 neutron cross section evaluation work at Oak Ridge National Laboratory (ORNL), AEA Technology (Harwell) and Lockheed Martin Corp.-Schenectady (LMS), which has influenced, or appeared in, ENDF/B-VI through Release 5. The discussion is restricted to the thermal and resolved resonance regions, apart from some questions about the unresolved region which still need investigation. The important role which benchmark testing has played will be touched on.

Lubitz, C. [Lockheed Martin Corp., Schenectady, NY (United States)

1998-10-01T23:59:59.000Z

408

Neutron-Induced Cross Sections Measurements of Calcium  

Science Conference Proceedings (OSTI)

To support the US Department of Energy Nuclear Criticality Safety Program neutron induced cross section experiments were performed at the Geel Electron Linear Accelerator of the Institute for Reference Material and Measurements of the Joint Research Centers, European Union. Neutron capture and transmission measurements were carried out using a metallic calcium sample. The obtained data will be used for a new calcium evaluation, which will be submitted with its covariances to the ENDBF/B nuclear data base.

Guber, Klaus H [ORNL; Kopecky, S. [EC-JRC-IRMM, Geel, Belgium; Schillebeeckx, P. [EC-JRC-IRMM, Geel, Belgium; Kauwenberghs, K. [EC-JRC-IRMM, Geel, Belgium; Siegler, P. [EC-JRC-IRMM, Geel, Belgium

2013-01-01T23:59:59.000Z

409

Inclusive jet cross-section measurement at CDF  

SciTech Connect

The CDF Collaboration has measured the inclusive jet cross section using 1992-93 collider data at 1.8 TeV. The CDF measurement is in very good agreement with NLO QCD predictions for transverse energies (E{sub T}) below 200 GeV. However, it is systematically higher than NLO QCD predictions for E{sub T} above 200 GeV.

Norniella, Olga; /Barcelona, IFAE

2007-05-01T23:59:59.000Z

410

Top quark pair production cross section at the Tevatron  

SciTech Connect

Top quark pair production cross section has been measured at the Tevatron by CDF and D0 collaborations using different channels and methods, in order to test standard model predictions, and to search for new physics hints affecting the t{bar t} production mechanism or decay. Measurements are carried out with an integrated luminosity of 1.0 to 2.0 fb{sup -1}, and are found to be consistent with standard model expectations.

Cortiana, Giorgio; /INFN, Padua /Padua U.

2008-04-01T23:59:59.000Z

411

Top Quark Production Cross Section at the Tevatron  

SciTech Connect

An overview of the preliminary results of the top quark pair production cross section measurements at a center-of-mass energy of 1.96 TeV carried out by the CDF and D0 collaborations is presented. The data samples used for the analyses are collected in the current Tevatron run and correspond to an integrated luminosity from 360 pb{sup -1} up to 760 pb{sup -1}.

Shabalina, E.; /Chicago U.

2006-05-01T23:59:59.000Z

412

Towards Reliable Cross Sections for National Security Applications  

Science Conference Proceedings (OSTI)

Stockpile stewardship requires the description of weapons performance without resorting to underground nuclear testing. In the earlier tests, selected isotopes were used as detectors, and recovered after irradiation. Aspects of nuclear device performance were inferred by comparing the measured isotopic ratios to those predicted from simulations. The reaction flows that produce the final isotopic distributions proceed through regions of the nuclear chart that include unstable nuclei. Presently, improved nuclear data input is required to reanalyze prior tests and to certify the stockpile's reliability and safety. Many important cross sections are unknown, as is shown in the example of the Yttrium reaction network (Figure 1). The relevant reactions include (n,2n), (n,n'), (n,gamma), (n,p) and other charged-particle emitting reactions. The cross sections have to be calculated or inferred from indirect measurements. In both cases, reliable optical models that are valid a few nucleons away from stability are needed. The UNEDF Nuclear Reaction activities address this need by combining nuclear-structure input from UNEDF structure calculations with modern reaction theory and large-scale computational capabilities to develop microscopic nucleon-nucleus optical potentials that can be extrapolated to unstable nuclei. In addition, the reaction calculation tools and optical models developed in this context are proving valuable for planning and interpreting indirect (surrogate) measurements of the required cross sections.

Escher, J E; Dietrich, F S; Nobre, G A; Thompson, I J

2011-02-24T23:59:59.000Z

413

File:Section106examplereport.pdf | Open Energy Information  

Open Energy Info (EERE)

Section106examplereport.pdf Section106examplereport.pdf Jump to: navigation, search File File history File usage File:Section106examplereport.pdf Size of this preview: 463 × 599 pixels. Other resolution: 464 × 600 pixels. Go to page 1 2 3 4 5 6 7 8 Go! next page → next page → Full resolution ‎(1,272 × 1,645 pixels, file size: 2.23 MB, MIME type: application/pdf, 8 pages) File history Click on a date/time to view the file as it appeared at that time. Date/Time Thumbnail Dimensions User Comment current 10:35, 20 November 2012 Thumbnail for version as of 10:35, 20 November 2012 1,272 × 1,645, 8 pages (2.23 MB) Dklein2012 (Talk | contribs) You cannot overwrite this file. Edit this file using an external application (See the setup instructions for more information) File usage There are no pages that link to this file.

414

Neutron Cross Section Measurements at the Spallation Neutron Source  

Science Conference Proceedings (OSTI)

With the prospect of construction of the Spallation Neutron Source (SNS) at ORNL, and the fantastic high neutron flux, new, up to now impossible, experiments seem to be feasible in the fields of applied nuclear physics and astrophysics. These experiments will supply crucial neutron-induced cross section data for radionuclides, which are badly needed by many applied physics programs. The SNS will be uniquely suited for measuring the cross sections of interest to nuclear criticality safety, accelerator transmutation of nuclear waste (ATW), and heavy element nucleosynthesis for astrophysics. Because the sample sizes required at current facilities are usually too large for practical measurements, scarce information of these cross sections is available. Using the high neutron flux at the SNS will allow these measurements to be made with samples about 40 times smaller than at the next best facility. The large reduction in sample size at the SNS will result in orders of magnitude reduction in background from the radioactive samples and make them much easier to produce; hence, a much wider range of samples will be accessible for measurement at the SNS than at any other facility.

Guber, K.H.

2001-08-24T23:59:59.000Z

415

Handbook of LHC Higgs Cross Sections: 3. Higgs Properties  

E-Print Network (OSTI)

This Report summarizes the results of the activities in 2012 and the first half of 2013 of the LHC Higgs Cross Section Working Group. The main goal of the working group was to present the state of the art of Higgs Physics at the LHC, integrating all new results that have appeared in the last few years. This report follows the first working group report Handbook of LHC Higgs Cross Sections: 1. Inclusive Observables (CERN-2011-002) and the second working group report Handbook of LHC Higgs Cross Sections: 2. Differential Distributions (CERN-2012-002). After the discovery of a Higgs boson at the LHC in mid-2012 this report focuses on refined prediction of Standard Model (SM) Higgs phenomenology around the experimentally observed value of 125-126 GeV, refined predictions for heavy SM-like Higgs bosons as well as predictions in the Minimal Supersymmetric Standard Model and first steps to go beyond these models. The other main focus is on the extraction of the characteristics and properties of the newly discovered particle such as couplings to SM particles, spin and CP-quantum numbers etc.

The LHC Higgs Cross Section Working Group; S. Heinemeyer; C. Mariotti; G. Passarino; R. Tanaka; J. R. Andersen; P. Artoisenet; E. A. Bagnaschi; A. Banfi; T. Becher; F. U. Bernlochner; S. Bolognesi; P. Bolzoni; R. Boughezal; D. Buarque; J. Campbell; F. Caola; M. Carena; F. Cascioli; N. Chanon; T. Cheng; S. Y. Choi; A. David; P. de Aquino; G. Degrassi; D. Del Re; A. Denner; H. van Deurzen; S. Diglio; B. Di Micco; R. Di Nardo; S. Dittmaier; M. Duhrssen; R. K. Ellis; G. Ferrera; N. Fidanza; M. Flechl; D. de Florian; S. Forte; R. Frederix; S. Frixione; S. Gangal; Y. Gao; M. V. Garzelli; D. Gillberg; P. Govoni; M. Grazzini; N. Greiner; J. Griffiths; A . V. Gritsan; C. Grojean; D. C. Hall; C. Hays; R. Harlander; R. Hernandez-Pinto; S. Hoche; J. Huston; T. Jubb; M. Kadastik; S. Kallweit; A. Kardos; L. Kashif; N. Kauer; H. Kim; R. Klees; M. Kramer; F. Krauss; A. Laureys; S. Laurila; S. Lehti; Q. Li; S. Liebler; X. Liu; H. E. Logan; G. Luisoni; M. Malberti; F. Maltoni; K. Mawatari; F. Maierhofer; H. Mantler; S. Martin; P. Mastrolia; O. Mattelaer; J. Mazzitelli; B. Mellado; K. Melnikov; P. Meridiani; D. J. Miller; E. Mirabella; S. O. Moch; P. Monni; N. Moretti; A. Muck; M. Muhlleitner; P. Musella; P. Nason; C. Neu; M. Neubert; C. Oleari; J. Olsen; G. Ossola; T. Peraro; K. Peters; F. Petriello; G. Piacquadio; C. T. Potter; S. Pozzorini; K. Prokofiev; I. Puljak; M. Rauch; D. Rebuzzi; L. Reina; R. Rietkerk; A. Rizzi; Y. Rotstein-Habarnau; G. P. Salam; G. Sborlini; F. Schissler; M. Schonherr; M. Schulze; M. Schumacher; F. Siegert; P. Slavich; J. M. Smillie; O. Stal; J. F. von Soden-Fraunhofen; M. Spira; I. W. Stewart; F. J. Tackmann; P. T. E. Taylor; D. Tommasini; J. Thompson; R. S. Thorne; P. Torrielli; F. Tramontano; N. V. Tran; Z. Trocsanyi; M. Ubiali; P. Vanlaer; M. Vazquez Acosta; T. Vickey; A. Vicini; W. J. Waalewijn; D. Wackeroth; C. Wagner; J. R. Walsh; J. Wang; G. Weiglein; A. Whitbeck; C. Williams; J. Yu; G. Zanderighi; M. Zanetti; M. Zaro; P. M. Zerwas; C. Zhang; T. J . E. Zirke; S. Zuberi

2013-07-04T23:59:59.000Z

416

Handbook of LHC Higgs Cross Sections: 1. Inclusive Observables  

E-Print Network (OSTI)

This Report summarizes the results of the first 10 months' activities of the LHC Higgs Cross Sections Working Group. The main goal of the working group was to present the status-of-art on Higgs Physics at the LHC integrating all new results that have appeared in the last few years. The Report is more than a mere collection of the proceedings of the general meetings. The subgroups have been working in different directions. An attempt has been made to present the first Report from these subgroups in a complete and homogeneous form. The subgroups' contributions correspondingly comprise the main parts of the Report. A significant amount of work has been performed in providing higher-order corrections to the Higgs-boson cross sections and pinning down the theoretical uncertainty of the Standard Model predictions. This Report comprises explicit numerical results on total cross sections, leaving the issues of event selection cuts and differential distributions to future publications. The subjects for further study are identified.

LHC Higgs Cross Section Working Group; S. Dittmaier; C. Mariotti; G. Passarino; R. Tanaka; J. Baglio; P. Bolzoni; R. Boughezal; O. Brein; C. Collins-Tooth; S. Dawson; S. Dean; A. Denner; S. Farrington; M. Felcini; M. Flechl; D. de Florian; S. Forte; M. Grazzini; C. Hackstein; T. Hahn; R. Harlander; T. Hartonen; S. Heinemeyer; J. Huston; A. Kalinowski; M. Krmer; F. Krauss; J. S. Lee; S. Lehti; F. Maltoni; K. Mazumdar; S. -O. Moch; A. Mck; M. Mhlleitner; P. Nason; C. Neu; C. Oleari; J. Olsen; S. Palmer; F. Petriello; G. Piacquadio; A. Pilaftsis; C. T. Potter; I. Puljak; J. Qian; D. Rebuzzi; L. Reina; H. Rzehak; M. Schumacher; P. Slavich; M. Spira; F. Stckli; R. S. Thorne; M. Vazquez Acosta; T. Vickey; A. Vicini; D. Wackeroth; M. Warsinsky; M. Weber; G. Weiglein; C. Weydert; J. Yu; M. Zaro; T. Zirke

2011-01-03T23:59:59.000Z

417

Idiosyncratic Consumption Risk and the Cross Section of Asset Returns  

E-Print Network (OSTI)

This paper investigates the importance of idiosyncratic consumption risk for the cross-sectional variation in average returns on stocks and bonds. If idiosyncratic consumption risk is not priced, the only pricing factor in a multiperiod economy is the rate of aggregate consumption growth. We oer evidence that the cross-sectional variance of consumption growth is also a priced factor. This demonstrates that consumers are not fully insured against idiosyncratic consumption risk, and that asset returns reect their attempts to reduce their exposure to this risk. We nd that over the sample period the resulting two-factor pricing model has lower Hansen-Jagannathan distances than the CAPM and the Fama-French three-factor model. Moreover, in the presence of the market factor and the size and book-to-market factors, the two consumption based factors retain explanatory power. Together with the results of Lettau and Ludvigson (2000), these ndings indicate that consumption-based asset pricing is relevant for explaining the cross-section of asset returns.

Kris Jacobs; Kevin Q. Wang

2004-01-01T23:59:59.000Z

418

Diffraction, Saturation and pp Cross Sections at the LHC  

E-Print Network (OSTI)

Results from the large hadron collider (LHC) show that no available Monte Carlo simulation incorporates our pre-LHC knowledge of soft and hard diffraction in a way that could be reliably extrapolated to LHC energies. As a simulation is needed to establish triggers, perform underlying event corrections and calculate acceptances, the lack of a robust simulation affects all measurements at the LHC. Particularly affected are the measurements of processes with large diffractive rapidity gaps, which constitute about one quarter of the inelastic cross section. In this paper, a previously described phenomenological model based on a saturation effect observed in single diffraction dissociation in pre-LHC data, validated by its successful application to several diffractive processes, is used to predict the total and total-inelastic proton-proton cross sections at the LHC. The prediction for the total-inelastic cross section at a center of mass collision energy of 7 TeV is compared with recent results from ATLAS and CMS.

Konstantin Goulianos

2011-05-25T23:59:59.000Z

419

Fully hadronic ttbar cross section measurement with ATLAS detector  

E-Print Network (OSTI)

The top quark pair production cross section in the fully hadronic final state is characterized by a six jet topology, two of which could be identified as originating from a b-quark using ATLAS b-tagging algorithms. Compared to other decay channels, this final state presents an advantageous larger branching ratio; on the other hand it suffers from a very large QCD multi-jet background, generally difficult to estimate from Monte Carlo simulation and therefore evaluated using data-driven techniques. The analysis is performed using 36pb-1 of pp collisions produced at the LHC with a center-of-mass energy of 7 TeV. The observed upper limit is set at 261 pb at 95% confidence level, where the expected Standard Model cross-section for the ttbar process is 165+11-16 pb. In the future, when the LHC luminosity increases, it is essential, to efficiently trigger on these fully hadronic ttbar events, to use dedicated triggers. An overview of the analysis for ttbar production cross section measurement in the fully hadronic final state and the state-of-the-art of the b-jet trigger performance estimation are presented in this contribution.

Claudia Bertella

2011-11-16T23:59:59.000Z

420

\\ttbar and single top cross sections at the Tevatron  

SciTech Connect

We present a summary of the latest measurements of the top pair and single top cross sections performed by the CDF and D0 collaborations at the Fermilab Tevatron collider. The Fermilab Tevatron collider ended its run on September 30, 2011 after delivering more than 10 fb{sup -1} of p{bar p} collision data per experiment at {radical}s = 1.96 TeV. A large sample of top quarks collected by the CDF and D0 experiments allows to perform precision measurements of their production which is predicted to occur within the standard model (SM) either in pairs via strong interactions or as single top events via electroweak interactions. Such measurements represent an important test of the theoretical calculations which predict the t{bar t} and single top production cross sections with a precision of 6% to 8% and 5%, respectively. Precise measurements of top pair cross section ({sigma}{sub t{bar t}}) in different t{bar t} final states and single top production via different production mechanisms are highly desirable as they are sensitive to the non-SM particles that may appear in top quark production or decays.

CDF, Elizaveta Shabalina for; collaborations, D0

2012-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "alcohol msds section" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


421

An evaluation of wind turbine blade cross section analysis techniques.  

SciTech Connect

The blades of a modern wind turbine are critical components central to capturing and transmitting most of the load experienced by the system. They are complex structural items composed of many layers of fiber and resin composite material and typically, one or more shear webs. Large turbine blades being developed today are beyond the point of effective trial-and-error design of the past and design for reliability is always extremely important. Section analysis tools are used to reduce the three-dimensional continuum blade structure to a simpler beam representation for use in system response calculations to support full system design and certification. One model simplification approach is to analyze the two-dimensional blade cross sections to determine the properties for the beam. Another technique is to determine beam properties using static deflections of a full three-dimensional finite element model of a blade. This paper provides insight into discrepancies observed in outputs from each approach. Simple two-dimensional geometries and three-dimensional blade models are analyzed in this investigation. Finally, a subset of computational and experimental section properties for a full turbine blade are compared.

Paquette, Joshua A.; Griffith, Daniel Todd; Laird, Daniel L.; Resor, Brian Ray

2010-03-01T23:59:59.000Z

422

From ZZ to ZH : How Low Can These Cross Sections Go or Everybody, Let's Cross Section Limbo!  

SciTech Connect

We report on two searches performed at the D0 detector at the Fermi National Laboratory. The first is a search for Z di-boson production with a theoretical cross section of 1.4 pb. The search was performed on 2.6 fb{sup -1} of data and contributed to the first observation of ZZ production at a hadron collider. The second is a search for a low mass Standard Model Higgs in 4.2 fb{sup -1} of data. The Higgs boson is produced in association with a Z boson where the Higgs decays hadronically and the Z decays to two leptons. The ZZ search was performed in both the di-electron and di-muon channels. For the ZH search, we will focus on the muonic decays where we expanded the traditional coverage by considering events in which one of the two muons fails the selection requirement, and is instead reconstructed as an isolated track. We consider Higgs masses between 100 and 150 GeV, with theoretical cross sections ranging from 0.17 to 0.042 pb, and set upper limits on the ZH production cross-section at 95% confidence level.

Strauss, Emanuel Alexandre; /SUNY, Stony Brook

2009-08-01T23:59:59.000Z

423

From ZZ to ZH : How Low Can These Cross Sections Go or Everybody, Let's Cross Section Limbo!  

SciTech Connect

We report on two searches performed at the D0 detector at the Fermi National Laboratory. The first is a search for Z di-boson production with a theoretical cross section of 1.4 pb. The search was performed on 2.6 fb{sup -1} of data and contributed to the first observation of ZZ production at a hadron collider. The second is a search for a low mass Standard Model Higgs in 4.2 fb{sup -1} of data. The Higgs boson is produced in association with a Z boson where the Higgs decays hadronically and the Z decays to two leptons. The ZZ search was performed in both the di-electron and di-muon channels. For the ZH search, we will focus on the muonic decays where we expanded the traditional coverage by considering events in which one of the two muons fails the selection requirement, and is instead reconstructed as an isolated track. We consider Higgs masses between 100 and 150 GeV, with theoretical cross sections ranging from 0.17 to 0.042 pb, and set upper limits on the ZH production cross-section at 95% confidence level.

Strauss, Emanuel Alexandre; /SUNY, Stony Brook

2009-08-01T23:59:59.000Z

424

Black liquor combustion validated recovery boiler modeling: Final year report. Volume 2 (Appendices I, section 5 and II, section 1)  

DOE Green Energy (OSTI)

This project was initiated in October 1990, with the objective of developing and validating a new computer model of a recovery boiler furnace using a computational fluid dynamics (CFD) code specifically tailored to the requirements for solving recovery boiler flows, and using improved submodels for black liquor combustion based on continued laboratory fundamental studies. The key tasks to be accomplished were as follows: (1) Complete the development of enhanced furnace models that have the capability to accurately predict carryover, emissions behavior, dust concentrations, gas temperatures, and wall heat fluxes. (2) Validate the enhanced furnace models, so that users can have confidence in the predicted results. (3) Obtain fundamental information on aerosol formation, deposition, and hardening so as to develop the knowledge base needed to relate furnace model outputs to plugging and fouling in the convective sections of the boiler. (4) Facilitate the transfer of codes, black liquid submodels, and fundamental knowledge to the US kraft pulp industry. Volume 2 contains the last section of Appendix I, Radiative heat transfer in kraft recovery boilers, and the first section of Appendix II, The effect of temperature and residence time on the distribution of carbon, sulfur, and nitrogen between gaseous and condensed phase products from low temperature pyrolysis of kraft black liquor.

Grace, T.M.; Frederick, W.J.; Salcudean, M.; Wessel, R.A.

1998-08-01T23:59:59.000Z

425

Syngas production by plasma treatments of alcohols, bio-oils and wood This article has been downloaded from IOPscience. Please scroll down to see the full text article.  

E-Print Network (OSTI)

Syngas production by plasma treatments of alcohols, bio-oils and wood This article has been Contact us My IOPscience #12;Syngas production by plasma treatments of alcohols, bio-oils and wood K to recover energy from biomass. The Syngas produced from biomass can be used to power internal combustion

426

The potential for alcohols and related ethers to displace conventional gasoline components  

DOE Green Energy (OSTI)

The United States Department of Energy is required by law to determine the feasibility of producing sufficient replacement fuels to replace 30 percent of the projected United States consumption of motor fuels by light duty vehicles in the year 2010. A replacement fuel is a non-petroleum portion of gasoline, including alcohols, natural gas and certain other components. A linear program has been used to study refinery impacts for production of ``low petroleum`` gasolines, which contain replacement fuels. The analysis suggests that high oxygenation is the key to meeting the replacement fuel target, and major contributors to cost increase can include investment in processes to produce olefins for etherification with alcohols. High oxygenation can increase the costs of control of vapor pressure, distillation properties, and pollutant emissions of gasolines. Year-round low petroleum gasoline with near-30 percent non-petroleum might be produced with cost increases of 23 to 37 cents per gallon, with substantial decreases in greenhouse gas emissions in some cases. Cost estimates are sensitive to assumptions about extrapolation of a national model for pollutant emissions, availability of raw materials and other issues. Reduction in crude oil use, a major objective of the low petroleum gasoline program, is 10 to 17 percent in the analysis.

Hadder, G.R. [Oak Ridge National Lab., TN (United States); McNutt, B.D. [USDOE, Washington, DC (United States)

1996-02-01T23:59:59.000Z

427

Environmental planning and assessment for highway vehicle use of alcohol fuels  

DOE Green Energy (OSTI)

Argonne National Laboratory is assisting the Office of Transportation Programs of the U.S. DOE in performing the required environmental planning and assessment for highway vehicle alcohol fuel commercialization in accordance with the National Environmental Policy Act of 1969 (NEPA). In this presentation the process for planning and assessment is given, specific documents resulting from the process are explained. NEPA requires an environmental impact statement (EIS) for every major federal action that may have a significant impact on the quality of the human environment. Three types of environmental documents record this process: the Environmental Development Plan (EDP), the Environmental Assessment (EA) and the Environmental Impact Statement (EIS). The transportation EDP describes the energy conserving technologies; identifies and ranks environmental concerns; outlines strategies to resolve the concerns on a priority basis; and proposes a research program to implement the strategies. This is done annually for the division. In addition, environmental codumentation is scheduled for each technology as it reaches different stages of development. One major document is the EA, prepared when it is not clear whether an EIS is necessary. The information to make such a decision is collected in one detailed assessment of the technology or program. An EIS may then be written if impacts are expected to be significant. An EA is being performed for alcohol (neat and blends) fuels for highway vehicles by ANL.

Bernard, III, M J; Bevilaqua, O M

1979-01-01T23:59:59.000Z

428

(100) facets of ?-Al2O3: the active surfaces for alcohol dehydration reactions  

DOE Green Energy (OSTI)

Temperature programmed desorption (TPD) of ethanol, and methanol dehydration reaction were studied on ?-Al2O3 in order to identify the catalytic active sites for alcohol dehydration reactions. Two high temperature (> 473 K) desorption features were observed following ethanol adsorption. Samples calcined at T?473 K displayed a desorption feature in the 523-533 K temperature range, while those calcined at T ? 673 K showed a single desorption feature at 498 K. The switch from the high to low temperature ethanol desorption correlated well with the dehydroxylation of the (100) facets of ?-Al2O3 that was predicted at 550 K DFT calculations. Theoretical DFT simulations of the mechanism of dehydration. on clean and hydroxylated ?-Al2O3(100) surfaces, find that a concerted elimination of ethylene from an ethanol molecule chemisorbed at an Al3+ pentacoordinated site is the rate limiting step for catalytic cycle on both surfaces. Furthermore, titration of the pentacoordinate Al3+ sites on the (100) facets of ?-Al2O3 by BaO completely turned off the methanol dehydration reaction activity. These results unambiguously demonstrate that only the (100) facets on ?-Al2O3 are the catalytic active surfaces for alcohol dehydration.

Kwak, Ja Hun; Mei, Donghai; Peden, Charles HF; Rousseau, Roger J.; Szanyi, Janos

2011-05-01T23:59:59.000Z

429

Under the influence of alcohol: The effect of ethanol and methanol on lipid bilayers  

E-Print Network (OSTI)

Extensive microscopic molecular dynamics simulations have been performed to study the effects of short-chain alcohols, methanol and ethanol, on two different fully hydrated lipid bilayer systems in the fluid phase at 323 K. It is found that ethanol has a stronger effect on the structural properties of the membranes. In particular, the bilayers become more fluid and permeable: Ethanol molecules are able to penetrate through the membrane in typical time scales of about 200 ns whereas for methanol that time scale is considerably longer, at least of the order of microseconds. We find good agreement with NMR and micropipette studies. We have also measured partitioning coefficients and the rate of crossing events for alcohols, i.e., typical time scale it takes for a molecule to cross the lipid bilayer and to move from one leaflet to the other. For structural properties, two-dimensional centre of mass radial-distribution functions indicate the possibility for quasi long-range order for ethanol-ethanol correlations in contrast to liquid-like behaviour for all other combinations.

Michael Patra; Emppu Salonen; Emma Terama; Roland Faller; Bryan W. Lee; Juha Holopainen; Mikko Karttunen

2004-08-05T23:59:59.000Z

430

MOX Cross-Section Libraries for ORIGEN-ARP  

Science Conference Proceedings (OSTI)

The use of mixed-oxide (MOX) fuel in commercial nuclear power reactors operated in Europe has expanded rapidly over the past decade. The predicted characteristics of MOX fuel such as the nuclide inventories, thermal power from decay heat, and radiation sources are required for design and safety evaluations, and can provide valuable information for non-destructive safeguards verification activities. This report describes the development of computational methods and cross-section libraries suitable for the analysis of irradiated MOX fuel with the widely-used and recognized ORIGEN-ARP isotope generation and depletion code of the SCALE (Standardized Computer Analyses for Licensing Evaluation) code system. The MOX libraries are designed to be used with the Automatic Rapid Processing (ARP) module of SCALE that interpolates appropriate values of the cross sections from a database of parameterized cross-section libraries to create a problem-dependent library for the burnup analysis. The methods in ORIGEN-ARP, originally designed for uranium-based fuels only, have been significantly upgraded to handle the larger number of interpolation parameters associated with MOX fuels. The new methods have been incorporated in a new version of the ARP code that can generate libraries for low-enriched uranium (LEU) and MOX fuel types. The MOX data libraries and interpolation algorithms in ORIGEN-ARP have been verified using a database of declared isotopic concentrations for 1042 European MOX fuel assemblies. The methods and data are validated using a numerical MOX fuel benchmark established by the Organization for Economic Cooperation and Development (OECD) Working Group on burnup credit and nuclide assay measurements for irradiated MOX fuel performed as part of the Belgonucleaire ARIANE International Program.

Gauld, I.C.

2003-07-01T23:59:59.000Z

431

Microsoft Word - Section 311 AL FAL Feb 17 2010  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

4 4 Acquisition Regulation Date 03/01/10 Department of Energy No. FAL 2010-04 Financial Assistance Regulations Date 03/01/10 ACQUISITION/FINANCIAL ASSISTANCE LETTER This Acquisition/Financial Assistance Letter is issued under the authority of the DOE and NNSA Senior Procurement Executives. Subject: Congressional Notification of Pending Contract or Financial Assistance Actions in excess of $1 Million References: Energy and Water Development and Related Agencies Appropriations Act, 2010 Pub.L. 111-85, Title III, section 311 Acquisition Guide, Chapter 5.1, Release of Information: Congressional Notification and Long- range Acquisition Estimates

432

ORISE Contract, PART I - SCHEDULE, Section G Contract Administration Data  

NLE Websites -- All DOE Office Websites (Extended Search)

G G CONTRACT ADMINISTRATION DATA G.1 CORRESPONDENCE PROCEDURES (OCT 2004) ................................................... 3 G.2 CONTRACTING OFFICER'S REPRESENTATIVE (COR) (MAY 1997) ............... 3 G.3 CONTRACT ADMINISTRATION (MAY 1997).......................................................... 4 G.4 PAYMENT OF BASE FEE AND AWARD FEE (NOV 2004)..................................... 4 Section G - Page 1 of 4 G.5 COST REPORTING REQUIREMENTS INVOLVING RECOVERY ACT ....... 4 PROJECT WORK (APR 2009) G.6 INDIRECT CHARGES INVOLVING RECOVERY ACT PROJECT .................4 WORK (APR 2009) G.7 PAYMENT OF FIXED FEE ..................................................................................4 DE-AC05-06OR23100

433

Scaling of cross sections in ion-atom collisions  

DOE Green Energy (OSTI)

Differential electron emission at 15{degrees} is investigated for 50-500 keV/amu hydrogen impacting on He and H targets. From hydrogen particles (H, H{sup +}, H{sub 2}{sup +}, H{sub 3}{sup +}) ratios of cross sections relative to proton impact data, it is shown how bound projectile electrons influence the differential electron emission and where different ionization mechanisms are important. It is demonstrated that the H{sub 2}{sup +} and H{sub 3}{sup +} molecular ions interact as though they are composed of independent nuclei with the appropriate number of bound electrons, the electronic structure of the components appearing to be unimportant.

DuBois, R.D.

1994-11-01T23:59:59.000Z

434

Photon plus Jet Cross Sections at the Tevatron  

E-Print Network (OSTI)

Photon plus jet production has been studied by the D0 and CDF experiments in Run II of the Fermilab Tevatron Collider at a center of mass energy of sqrt{s}=1.96 TeV. Measurements of the inclusive photon plus jet, di-photon and photon plus b jet cross section are presented. They are based on integrated luminosities between 0.2 fb^-1 and 1.1 fb^-1. The results are compared to perturbative QCD calculations in various approximations.

Lars Sonnenschein

2008-04-03T23:59:59.000Z

435

The shape of heavy ion upset cross section curves  

Science Conference Proceedings (OSTI)

An approach is developed to describe heavy ion single event upset cross section curves. It accounts for all significant mechanisms which cause the curve to deviate from ideal, step function-like behavior. The method is developed in terms of the charge deposited by an incident ion in a memory cell and is therefore free of ambiguities associated with the effective LET concept. It is suggested that this type of approach is an improvement over current methods used to characterize a memory response to accelerator tests. This has significant implications for predicting space upset rates.

Xapsos, M.A. (Naval Research Lab., Washington, DC (United States). Radiation Effects Branch); Weatherford, T.R.; Shapiro, P. (SFA, Inc., Landover, MD (United States))

1993-12-01T23:59:59.000Z

436

Section III, Division 5 - Development And Future Directions  

SciTech Connect

This paper provides commentary on a new division under Section III of the ASME Boiler and Pressure Vessel (BPV) Code. This new Division 5 has an issuance date of November 1, 2011 and is part of the 2011 Addenda to the 2010 Edition of the BPV Code. The new Division covers the rules for the design, fabrication, inspection and testing of components for high temperature nuclear reactors. Information is provided on the scope and need for Division 5, the structure of Division 5, where the rules originated, the various changes made in finalizing Division 5, and the future near-term and long-term expectations for Division 5 development.

Morton, Dana K. [Idaho National Laboratory (INL); Jetter, Robert I [Consultant; Nestell, James E. [MPR Associates Inc.; Burchell, Timothy D [ORNL; Sham, Sam [ORNL

2012-01-01T23:59:59.000Z

437

Predictive model of nucleon-nucleus scattering cross sections  

DOE Green Energy (OSTI)

Nucleon total reaction and neutron total cross sections as well as differential (including spin) observables from 25 to 300 MeV for stable nuclei from 6Li to 238U have been predicted that are in good agreement with measured data. Those predictions have been made using non-local, energy dependent, and complex optical potentials in coordinate space formed by full folding of effective nucleon-nucleon interactions with realistic nuclear ground state densities. By inverse kinematics the same model prescription describes exotic (radioactive) nuclei scattering from hydrogen as a target and the results reveal the extended (neutron) distributions such nuclei can have.

Amos, K. (Ken); Deb, P. (Pradip); Karataglidis, S. (Steven); Madland, D. G.

2001-01-01T23:59:59.000Z

438

CROSS SECTION EVALUATIONS FOR ENDF/B-VII.  

SciTech Connect

This is the final report of the work performed under the LANL contract on neutron cross section evaluations for ENDF/B-VII (April 2005-May 2006). The purpose of the contract was to ensure seamless integration of the LANL neutron cross section evaluations in the new ENDF/B-VII library. The following work was performed: (1) LANL evaluated data files submitted for inclusion in ENDF/B-VII were checked and, when necessary, formal formatting errors were corrected. As a consequence, ENDF checking codes, run on all LANL files, do not report any errors that would rise concern. (2) LANL dosimetry evaluations for {sup 191}Ir and {sup 193}Ir were completed to match ENDF requirements for the general purpose library suitable for transport calculations. A set of covariances for both isotopes is included in the ENDF files. (3) Library of fission products was assembled and successfully tested with ENDF checking codes, processed with NJOY-99.125 and simple MCNP calculations. (4) KALMAN code has been integrated with the EMPIRE system to allow estimation of covariances based on the combination of measurements and model calculations. Covariances were produced for 155,157-Gd and also for 6 remaining isotopes of Gd.

HERMAN, M.; ROCHMAN, D.; OBLOZINSKY, P.

2006-06-05T23:59:59.000Z

439

Experimental researches of fuelling systems and alcohol blends on combustion and emissions in a two stroke Si engine  

Science Conference Proceedings (OSTI)

Fuelling systems play a major role in the process of air-fuel mixture formation, due to this fact; the aim of this paper was to achieve an optimal mixture, which results in low exhaust emissions and best behavior of the combustion process. In order to ... Keywords: alcohols, combustion, engine, exhaust emissions, gasoline

Mihai Aleonte; Corneliu Cofaru; Radu Cosgarea; Maria Luminita Scutaru; Liviu Jelenschi; Gabriel Sandu

2011-04-01T23:59:59.000Z

440

Techno-Economics for Conversion of Lignocellulosic Biomass to Ethanol by Indirect Gasification and Mixed Alcohol Synthesis  

DOE Green Energy (OSTI)

This techno-economic study investigates the production of ethanol and a higher alcohols coproduct by conversion of lignocelluosic biomass to syngas via indirect gasification followed by gas-to-liquids synthesis over a precommercial heterogeneous catalyst. The design specifies a processing capacity of 2,205 dry U.S. tons (2,000 dry metric tonnes) of woody biomass per day and incorporates 2012 research targets from NREL and other sources for technologies that will facilitate the future commercial production of cost-competitive ethanol. Major processes include indirect steam gasification, syngas cleanup, and catalytic synthesis of mixed alcohols, and ancillary processes include feed handling and drying, alcohol separation, steam and power generation, cooling water, and other operations support utilities. The design and analysis is based on research at NREL, other national laboratories, and The Dow Chemical Company, and it incorporates commercial technologies, process modeling using Aspen Plus software, equipment cost estimation, and discounted cash flow analysis. The design considers the economics of ethanol production assuming successful achievement of internal research targets and nth-plant costs and financing. The design yields 83.8 gallons of ethanol and 10.1 gallons of higher-molecular-weight alcohols per U.S. ton of biomass feedstock. A rigorous sensitivity analysis captures uncertainties in costs and plant performance.

Abhijit Dutta; Michael Talmadge; Jesse Hensley; Matt Worley; Doug Dudgeon; David Barton; Peter Groenendijk; Daniela Ferrari; Brien Stears; Erin Searcy; Christopher Wright; J. Richard Hess

2012-07-01T23:59:59.000Z

Note: This page contains sample records for the topic "alcohol msds section" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


441

Investigation of syngas interaction in alcohol synthesis catalysts. Quarterly technical progress report, January 1, 1995--March 31, 1995  

DOE Green Energy (OSTI)

Work is described on the investigations of the interaction of syngas in the preparation of alcohols. The analysis of work performed on copper/cobalt/chromium catalysts and the effect of the method of preparation on magnetic properties of the catalysts is discussed.

Akundi, M.A.

1995-10-01T23:59:59.000Z

442

Investigation of syngas interaction in alcohol synthesis catalysts. Quartery technical progress report, July 1, 1995--September 31, 1995  

DOE Green Energy (OSTI)

This report presents the work done on {open_quotes}Investigation of Syngas Interaction in Alcohol Synthesis Catalysts{close_quotes} during the last three months. In this report the results of the work done on the effect of CO adsorption on the magnetic character of cobalt in the Cu/Co/Cr catalysts is discussed.

Akundi, M.A.

1996-02-01T23:59:59.000Z

443

The economical production of alcohol fuels from coal-derived synthesis gas: Case studies, design, and economics  

DOE Green Energy (OSTI)

This project is a combination of process simulation and catalyst development aimed at identifying the most economical method for converting coal to syngas to linear higher alcohols to be used as oxygenated fuel additives. There are two tasks. The goal of Task 1 is to discover, study, and evaluate novel heterogeneous catalytic systems for the production of oxygenated fuel enhancers from synthesis gas, and to explore, analytically and on the bench scale, novel reactor and process concepts for use in converting syngas to liquid fuel products. The goal of Task 2 is to simulate, by computer, energy efficient and economically efficient processes for converting coal to energy (fuel alcohols and/or power). The primary focus is to convert syngas to fuel alcohols. This report contains results from Task 2. The first step for Task 2 was to develop computer simulations of alternative coal to syngas to linear higher alcohol processes, to evaluate and compare the economics and energy efficiency of these alternative processes, and to make a preliminary determination as to the most attractive process configuration. A benefit of this approach is that simulations will be debugged and available for use when Task 1 results are available. Seven cases were developed using different gasifier technologies, different methods for altering the H{sub 2}/CO ratio of the syngas to the desired 1.1/1, and with the higher alcohol fuel additives as primary products and as by-products of a power generation facility. Texaco, Shell, and Lurgi gasifier designs were used to test gasifying coal. Steam reforming of natural gas, sour gas shift conversion, or pressure swing adsorption were used to alter the H{sub 2}/CO ratio of the syngas. In addition, a case using only natural gas was prepared to compare coal and natural gas as a source of syngas.

NONE

1995-10-01T23:59:59.000Z

444

Liquid Fuel From Renewable Electricity and Bacteria: Electro-Autotrophic Synthesis of Higher Alcohols  

SciTech Connect

Electrofuels Project: UCLA is utilizing renewable electricity to power direct liquid fuel production in genetically engineered Ralstonia eutropha bacteria. UCLA is using renewable electricity to convert carbon dioxide into formic acid, a liquid soluble compound that delivers both carbon and energy to the bacteria. The bacteriaare genetically engineered to convert the formic acid into liquid fuelin this case alcohols such as butanol. The electricity required for the process can be generated from sunlight, wind, or other renewable energy sources. In fact, UCLAs electricity-to-fuel system could be a more efficient way to utilize these renewable energy sources considering the energy density of liquid fuel is much higher than the energy density of other renewable energy storage options, such as batteries.

2010-07-01T23:59:59.000Z

445

Optimization of Rhodium-Based Catalysts for Mixed Alcohol Synthesis -- 2011 Progress Report  

SciTech Connect

Pacific Northwest National Laboratory has been conducting research to investigate the feasibility of producing mixed alcohols from biomass-derived synthesis gas (syngas). In recent years, this research has primarily involved the further development of catalysts containing rhodium and manganese based on the results of earlier catalyst screening tests. Research during FY 2011 continued to examine the performance of RhMn catalysts on alternative supports including selected zeolite, silica, and carbon supports. Catalyst optimization continued using both the Davisil 645 and Merck Grade 7734 silica supports. Research also was initiated in FY 2011, using the both Davisil 645 silica and Hyperion CS-02C-063 carbon supports, to evaluate the potential for further improving catalyst performance, through the addition of one or two additional metals as promoters to the catalysts containing Rh, Mn, and Ir.

Gerber, Mark A.; Gray, Michel J.; Albrecht, Karl O.; Rummel, Becky L.

2011-10-01T23:59:59.000Z

446

Optimization of Rhodium-Based Catalysts for Mixed Alcohol Synthesis -- 2010 Progress Report  

SciTech Connect

Pacific Northwest National Laboratory has been conducting research for the U.S. Department of Energy, Energy Efficiency Renewable Energy, Biomass Program to investigate the feasibility of producing mixed alcohols from biomass-derived synthesis gas. In recent years this research has primarily involved the further development of a silica-supported catalyst containing rhodium and manganese that was selected from earlier catalyst screening tests. A major effort during 2010 was to examine alternative catalyst supports to determine whether other supports, besides the Davisil 645 silica, would improve performance. Optimization of the Davisil 645 silica-supported catalyst also was continued with respect to candidate promoters iridium, platinum, and gallium, and examination of selected catalyst preparation and activation alternatives for the baseline RhMn/SiO2 catalyst.

Gerber, Mark A.; Gray, Michel J.; Albrecht, Karl O.; White, J. F.; Rummel, Becky L.; Stevens, Don J.

2010-10-01T23:59:59.000Z

447

Weak dispersive forces between glass-gold macroscopic surfaces in alcohols  

E-Print Network (OSTI)

In this work we concentrate on an experimental validation of the Lifshitz theory for van der Waals and Casimir forces in gold-alcohol-glass systems. From this theory weak dispersive forces are predicted when the dielectric properties of the intervening medium become comparable to one of the interacting surfaces. Using inverse colloid probe atomic force microscopy dispersive forces were measured occasionally and under controlled conditions by addition of salt to screen the electrostatic double layer force if present. The dispersive force was found to be attractive, and an order of magnitude weaker than that in air. Although the theoretical description of the forces becomes less precise for these systems even with full knowledge of the dielectric properties, we find still our results in reasonable agreement with Lifshitz theory.

P. J. van Zwol; G. Palasantzas; J. Th. M. DeHosson

2009-04-03T23:59:59.000Z

448

Adsorption of various alcohols on Illinois No. 6 coal in aqueous solutions  

SciTech Connect

Hydrophilicity, hydrophobicity and aromacity of Illinois {number_sign}6 coal in water are relatively determined by evaluating equilibrium physical/chemical adsorption of probe compounds on the coal. Experiments on equilibrium adsorption loadings of various additives on 60--200 mesh Illinois {number_sign}6 coal (DECS-2; Randolph county) were performed to investigate relatively surface properties of the coal at 25{degree}C. The additives include various alcohols, alkanes and aromatic compounds. The main objectives of this research are to evaluate relatively surface properties of raw coals, treated coals and coal minerals with the inverse liquid chromatography technique, using various probe compounds, to analyze flotation recoveries of coals with a micro-flotation apparatus in order to relate coal floatability to evaluated coal surface properties, and to delineate roles of coal-cleaning/handling additives with the inverse liquid chromatography technique.

Kwon, K.C.; Rigby, R.R.

1993-07-01T23:59:59.000Z

449

Design of a high activity and selectivity alcohol catalyst. [Design of a flow microreactor  

DOE Green Energy (OSTI)

Research on the design of a high selectivity alcohol catalyst continued. During the first quarter of this project, our goals have been to overhaul key experimental equipment used in the previous project, plan and design new equipment and to identify a person to carry out the research program. The flow microreactor, previously assembled, has been reactivated and major improvements have been made both to the reactor and its attendant analytical instrumentation. This equipment is described later in this report. In addition to this, a state-of-the-art hydrogen chemisorption instrument has been designed and the components for its construction have been ordered. Additionally, four recent publications by the principal investigators on the subject of this project have appeared. 3 figs.

Foley, H.C.; Mills, G.A.

1990-11-26T23:59:59.000Z

450

Mutant alcohol dehydrogenase leads to improved ethanol tolerance in Clostridium thermocellum  

Science Conference Proceedings (OSTI)

Clostridium thermocellum is a thermophilic, obligately anaerobic, Gram-positive bacterium that is a candidate microorganism for converting cellulosic biomass into ethanol through consolidated bioprocessing. Ethanol intolerance is an important metric in terms of process economics, and tolerance has often been described as a complex and likely multigenic trait for which complex gene interactions come into play. Here, we resequence the genome of an ethanol-tolerant mutant, show that the tolerant phenotype is primarily due to a mutated bifunctional acetaldehyde-CoA/alcohol dehydrogenase gene (adhE), hypothesize based on structural analysis that cofactor specificity may be affected, and confirm this hypothesis using enzyme assays. Biochemical assays confirm a complete loss of NADH-dependent activity with concomitant acquisition of NADPH-dependent activity, which likely affects electron flow in the mutant. The simplicity of the genetic basis for the ethanol-tolerant phenotype observed here informs rational engineering of mutant microbial strains for cellulosic ethanol production.

Brown, Steven D [ORNL; Guss, Adam M [ORNL; Karpinets, Tatiana V [ORNL; Parks, Jerry M [ORNL; Smolin, Nikolai [ORNL; Yang, Shihui [ORNL; Land, Miriam L [ORNL; Klingeman, Dawn Marie [ORNL; Bhandiwad, Ashwini [Thayer School of Engineering at Dartmouth; Rodriguez, Jr., Miguel [ORNL; Raman, Babu [Dow Chemical Company, The; Shao, Xiongjun [Thayer School of Engineering at Dartmouth; Mielenz, Jonathan R [ORNL; Smith, Jeremy C [ORNL; Keller, Martin [ORNL; Lynd, Lee R [Thayer School of Engineering at Dartmouth

2011-01-01T23:59:59.000Z

451

Optimization of Rhodium-Based Catalysts for Mixed Alcohol Synthesis 2012 Progress Report  

SciTech Connect

Pacific Northwest National Laboratory has been conducting research to investigate the feasibility of producing mixed alcohols from biomass-derived synthesis gas (syngas). In recent years, this research has primarily involved the further development of catalysts containing rhodium and manganese based on the results of earlier catalyst screening tests. Testing continued in FY 2012 to further improve the Ir-promoted RhMn catalysts on both silica and carbon supports for producing mixed oxygenates from synthesis gas. This testing re-examined selected alternative silica and carbon supports to follow up on some uncertainties in the results with previous test results. Additional tests were conducted to further optimize the total and relative concentrations of Rh, Mn, and Ir, and to examine selected promoters and promoter combinations based on earlier results. To establish optimum operating conditions, the effects of the process pressure and the feed gas composition also were evaluated.

Gerber, Mark A.; Gray, Michel J.; Albrecht, Karl O.; Thompson, Becky L.

2012-11-01T23:59:59.000Z

452

A plant kinetic study of alcoholic fermentation using reversed-flow gas chromatography  

SciTech Connect

The reversed-flow gas chromatographic sampling technique is used to study the kinetics of alcoholic fermentation in a factory in conjunction with measurements of suspended particles in the fermenting medium. It was found that the overall process consists of four phases which have different first-order rate constants during ethanol formation. The second phase is the slowest with its rate constant being 4.3 and 13 times smaller than that of the first and third phases, respectively. There is also a decrease of suspended particles during the second phase. These results show that there is the possibility of increasing the rate constant during this phase, thereby increasing the overall production rate of ethanol significantly and thus lowering its cost of production.

Economopoulos, N.; Athanassopoulos, N. (B.G. Spiliopoulos Distilleri S.A., Patras (Greece)); Katsanos, N.A.; Karaiskakis, G.; Agathonos, P.; Vassilakos, Ch. (Univ. of Patras (Greece))

1992-12-01T23:59:59.000Z

453

Investigation and demonstration of a rich combustor cold-start device for alcohol-fueled engines  

DOE Green Energy (OSTI)

The authors have completed a study in which they investigated the use of a rich combustor to aid in cold starting spark-ignition engines fueled with either neat ethanol or neat methanol. The rich combustor burns the alcohol fuel outside the engine under fuel-rich conditions to produce a combustible product stream that is fed to the engine for cold starting. The rich combustor approach significantly extends the cold starting capability of alcohol-fueled engines. A design tool was developed that simulates the operation of the combustor and couples it to an engine/vehicle model. This tool allows the user to determine the fuel requirements of the rich combustor as the vehicle executes a given driving mission. The design tool was used to design and fabricate a rich combustor for use on a 2.8 L automotive engine. The system was tested using a unique cold room that allows the engine to be coupled to an electric dynamometer. The engine was fitted with an aftermarket engine control system that permitted the fuel flow to the rich combustor to be programmed as a function of engine speed and intake manifold pressure. Testing indicated that reliable cold starts were achieved on both neat methanol and neat ethanol at temperatures as low as {minus}20 C. Although starts were experienced at temperatures as low as {minus}30 C, these were erratic. They believe that an important factor at the very low temperatures is the balance between the high mechanical friction of the engine and the low energy density of the combustible mixture fed to the engine from the rich combustor.

Hodgson, J.W.; Irick, D.K. [Univ. of Tennessee, Knoxville, TN (United States)

1998-04-01T23:59:59.000Z

454

Evaluation of Promoters for Rhodium-Based Catalysts for Mixed Alcohol Synthesis  

DOE Green Energy (OSTI)

Pacific Northwest National Laboratory (PNNL) and National Renewable Energy Laboratory (NREL) are conducting research to investigate the feasibility of producing mixed alcohols from biomass-derived synthesis gas (syngas). PNNL is tasked with obtaining commercially-available catalysts or preparing promising mixed-alcohol catalysts and screening them in a laboratory-scale reactor system. Commercially-available catalysts and the most promising experimental catalysts are provided to NREL for testing using a slipstream from a pilot-scale biomass gasifier. A total of 28 tests were conducted to evaluate 22 different promoters as well as an unpromoted catalyst. The following general trends were observed for the test results: The highest carbon selectivity to C2+ oxygenates occurred at the lowest reaction temperatures and accompanying lowest space time yields (STYs). The lowest carbon selectivity to C2+ oxygenates occurred at the highest reaction temperatures because of high carbon conversion to hydrocarbons. The highest C2+-oxygenate STYs occurred between 300C and 325C, with the gas hourly space velocity (GHSV) adjusted when necessary to maintain carbon conversion ranges between ~ 30 and 40 percent. Higher carbon selectivity to hydrocarbons at higher temperatures resulted in lower C2+-oxygenate STYs. When catalysts were heated to between 300C and 325C the catalysts showed evidence of some deactivation with respect to C2+ oxygenate productivity, accompanied by reduced chain growth for the hydrocarbon products. The degree of deactivation and the temperature at which it occurred varied between the different catalysts tested. Of all of the catalysts evaluated, the Li-promoted catalysts had the highest carbon selectivity to C2+ oxygenates (47 percent) under the conditions at which the maximum C2+-oxygenate STYs were obtained.

Gerber, Mark A.; White, James F.; Gray, Michel J.; Stevens, Don J.

2008-12-08T23:59:59.000Z

455

The economical production of alcohol fuels from coal-derived synthsis gas. Quarterly technical progress report number 10, 1 January 1994--31 March 1994  

DOE Green Energy (OSTI)

The WVU plug-flow microreactor system is now complete. Screening runs with this system will commence. Computer control is being installed in the second WVU unit. Additional hardware has been suggested for this system so that it can be used either to screen additional catalysts or to obtain kinetic data on selected catalyst samples. Synthetic preparations and characterizations of molybdenum-based sulfide and nitride catalysts are ongoing. Modelling studies are continuing satisfactorily. A more detailed model of the reaction kinetics, to account for individual alcohols rather than a lumped highter-alcohol, has been inserted into the model of a plug-flow reactor. A solution methodology to maximize the profitability of alcohol production, separation and blending has been developed. The temperatures, pressures, flowrates, and key component recoveries in the separation steps are the optimization variables. The probability of this process becoming economically feasible in the near future appears to be extremely small given the low return on capital investment associated with the production of alcohol from coal. If coal derived alcohols are to become alternative transportation fuels, then the capital cost associated with the process must be reduced, specifically the cost of the gasifiers, or significant changes need to be made in the composition of the mixed alcohol product. A methodology for performing Monte Carlo studies to determine quantitatively the uncertainties relevant to future decisions to build an alcohol-fuels plant is still being developed.

Not Available

1994-04-01T23:59:59.000Z

456

Microsoft Word - Attachment 1 Section 311 Contract Award Aug 2010  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

August 2010 version August 2010 version OPAM will date the letter The Honorable David R. Obey The Honorable Daniel K. Inouye Chairman, Committee on Appropriations Chairman, Committee on Appropriations U.S. House of Representatives U.S. Senate Washington, DC 20515 Washington, DC 20510 The Honorable Peter J. Visclosky The Honorable Byron L. Dorgan Chairman, Subcommittee on Energy Chairman, Subcommittee on Energy and Water Development and Water Development Committee on Appropriations Committee on Appropriations U.S. House of Representatives U.S. Senate Washington, DC 20515 Washington, DC 20510 Subject: Section 311 Notification of Pending Contract Action Dear Chairmen Obey, Inouye, Visclosky, and Dorgan: No earlier than three full business days from the date of this notification, the

457

Microsoft Word - Attachment 1 Section 311 Contract Award April 2010  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

April 2010 version April 2010 version OPAM will date the letter The Honorable David R. Obey The Honorable Daniel K. Inouye Chairman, Committee on Appropriations Chairman, Committee on Appropriations U.S. House of Representatives U.S. Senate Washington, DC 20515 Washington, DC 20510 The Honorable Peter J. Visclosky The Honorable Byron L. Dorgan Chairman, Subcommittee on Energy Chairman, Subcommittee on Energy and Water Development and Water Development Committee on Appropriations Committee on Appropriations U.S. House of Representatives U.S. Senate Washington, DC 20515 Washington, DC 20510 Subject: Section 311 Notification of Pending Contract Action Dear Chairmen Obey, Inouye, Visclosky, and Dorgan: No earlier than three full business days from the date of this notification, the

458

Potential Outline of Section 180(c) Policy and Procedures  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

7/21/2005 12:24 PM 7/21/2005 12:24 PM 1 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 APPENDIX C Allowable Activities/Training I. Introduction Allowable activities are those activities and purchases for which recipient jurisdictions will be allowed to use their Section 180(c) funds. The challenge in defining allowable activities is to strike a balance between meeting the recipients' need for flexibility and the funding agency's need to track measurable progress. More broadly defined activities allow the greatest flexibility for the recipient to tailor activities to their needs. More narrowly defined activities make the funds easier to track for the Federal agency but limit the recipient's flexibility. There also are legal requirements that bound the range of allowable activities. Good

459

Symmetry energy and nucleon-nucleon cross sections  

E-Print Network (OSTI)

The extension of the Boltzmann-Uehling-Uhlenbeck model of nucleus-nucleus collision is presented. The isospin-dependent nucleon-nucleon cross sections are estimated using the proper volume extracted from the equation of state of the nuclear matter transformed into the form of the Van der Waals equation of state. The results of such simulations demonstrate the dependence on symmetry energy which typically varies strongly from the results obtained using only the isospin-dependent mean-field. The evolution of the n/p multiplicity ratio with angle and kinetic energy, in combination with the elliptic flow of neutrons and protons, provides a suitable set of observables for determination of the density dependence of the symmetry energy. The model thus provides an environment for testing of equations of state, used for various applications in nuclear physics and astrophysics.

Martin Veselsky; Yu-Gang Ma

2013-03-11T23:59:59.000Z

460

Potential Outline of Section 180(c) Policy and Procedures  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

G G Policy or Rulemaking I. Introduction Version 22 1 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 The Department can implement Section 180(c) through a Departmental policy, through a rulemaking, or through some combination of the two. Many stakeholders over the years have requested a rulemaking because of concerns that a 180(c) policy that was crafted with extensive stakeholder input could be easily changed with a change of leadership at DOE. Factors for DOE management to consider in their decision are first, the legal and procedural differences between policy-making and rulemaking and, second, the scope of the rulemaking. II. Background There is no clear guidance as to when a Federal Agency should issue a policy or a regulation. Executive Order 12866 defines a regulation but does not disallow a policy

Note: This page contains sample records for the topic "alcohol msds section" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


461

Potential Outline of Section 180(c) Policy and Procedures  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Created on 7/21/2005 12:40 PM Created on 7/21/2005 12:40 PM 1 APPENDIX H Funding Allocation Method I. INTRODUCTION The Department can allocate Section 180(c) funds according to a formula, based upon jurisdictions' needs assessments, or a combination approach. The challenge is to balance the competing interests of recipient need, risk, equity, and program efficiency. II. BACKGROUND The 1998 Revised Proposed Policy and Procedures intended to allocate funds based on an applicant's assessment of their training and technical assistance needs. The scope of the assessment was limited to ensure the applicant considered only those needs related to the increment of need caused by NWPA shipments. The Draft Policy proposed a one- time planning grant of $150,000, to be distributed four years prior to the commencement

462

Section_701_Surveys_Reviews_and_Self-Assessments  

NLE Websites -- All DOE Office Websites (Extended Search)

701 701 Surveys and Reviews Description This section describes the programs and procedures in effect at Headquarters (HQ) to conduct Safeguards and Security (S&S) surveys and reviews. These activities are conducted to assure the Secretary of Energy, Departmental elements, and other government agencies that safeguards and security interests are being protected at the required level. The Office of Information Security (HS-92) is responsible for the conduct of all surveys and reviews of HQ facilities. It is also responsible for conducting an annual survey of overall HQ security operations. The HQ Survey Team has been established within HS-92 to carry out these surveys and review activities. Types and Frequencies of Surveys and Reviews:

463

Potential Outline of Section 180(c) Policy and Procedures  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

K K Matching Funds I. Introduction Version 20 1 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 OCRWM could require a small percentage of matching funds, possibly ten percent, from grant recipients. States could use their fees for the match. The intent of the match would be to leverage the impact of Section 180(c). The purposes of a match, according to a report by the GAO 1 , are first, to avoid supplantation or fiscal substitution of Federal money for state and local efforts and, second, to build sustainability of the gains created by the grant. The GAO report stated that "Ideally, grants should stimulate higher levels of preparedness and avoid simply subsidizing local functions that are traditionally state or local responsibilities."

464

Data Collection for HWIR: Section 10 - Farm Food Chain  

NLE Websites -- All DOE Office Websites (Extended Search)

DATA COLLECTION FOR THE DATA COLLECTION FOR THE HAZARDOUS WASTE IDENTIFICATION RULE SECTION 10.0 FARM FOOD CHAIN AND TERRESTRIAL FOODWEB DATA Work Assignment Managers Stephen M. Kroner and Technical Direction: David A. Cozzie U.S. Environmental Protection Agency Office of Solid Waste Washington, DC 20460 Prepared by: Center for Environmental Analysis Research Triangle Institute 3040 Cornwallis Road Research Triangle Park, NC 27709-2194 Under Contract No. 68-W-98-085 U.S. Environmental Protection Agency Office of Solid Waste Washington, DC 20460 October 1999 ACKNOWLEDGMENTS A number of individuals have been involved with the database development in support of the aquatic food web module. David Cozzie and Stephen Kroner of the U.S. Environmental Protection Agency (EPA), Office of Solid Waste, provided overall technical direction and review

465

SCWR Once-Through Calculations for Transmutation and Cross Sections  

SciTech Connect

It is the purpose of this report to document the calculation of (1) the isotopic evolution and of (2) the 1-group cross sections as a function of burnup of the reference Super Critical Water Reactor (SCWR), in a format suitable for the Fuel Cycle Option Campaign Transmutation Data Library. The reference SCWR design was chosen to be that described in [McDonald, 2005]. Super Critical Water Reactors (SCWR) are intended to operate with super-critical water (i.e. H2O at a pressure above 22 MPa and a temperature above 373oC) as a cooling and possibly also moderating fluid. The main mission of the SCWR is to generate lower cost electricity, as compared to current standard Light Water Reactors (LWR). Because of the high operating pressure and temperature, SCWR feature a substantially higher thermal conversion efficiency than standard LWR i.e. about 45% versus 33%, mostly due to an increase in the exit water temperature from ~300oC to ~500oC potentially resulting in a lower cost of generated electricity. The coolant remains single phase throughout the reactor and the energy conversion system, thus eliminating the need for pressurizers, steam generators, steam separators and dryers, further potentially reducing the reactor construction capital cost. The SCWR concept presented here is based on existing LWR technology and on a large number of existing fossil-fired supercritical boilers. However, it was concluded in [McDonald, 2005], that: Based on the results of this study, it appears that the reference SCWR design is not feasible. This conclusion appears based on the strong sensitivity of the design to small deviations in nominal conditions leading to small effects having a potentially large impact on the peak cladding temperature of some fuel rods. This was considered a major feasibility issue for the SCWR [McDonald, 2005]. After a description of the reference SCWR design, the Keno V 3-D single assembly model used for this analysis, as well as the calculated results, are presented. Additionally, the follwing information, presented in the appendixes, is intended to provide enough guidance that a researcher repeating the same task in the future should be able to obtain a vector of nuclei and cross sections ready for insertion into the transmutation library without any need for further instructions: (1) Complete TRITON/KENO-V input used for the analysis; (2) Inputs and detailed description of the usage of the OPUS utility, used to postproces and to extract the nuclei concentrations for the transmutation library; (3) Inputs and detailed description of the usage of the XSECLIST utility, used to postproces and to extract the 1-group cross sections for the transmutation library; (4) Details of an ad-hoc utility program developed to sort the nuclei and cross sections for the transmutation library.

ganda, francesco (090771)

2012-07-01T23:59:59.000Z

466

COMBUSTION TURBINE (CT) HOT SECTION COATING LIFE MANAGEMENT  

Science Conference Proceedings (OSTI)

The integrity of coatings used in hot section components of combustion turbine is crucial to the reliability of the buckets. This project was initiated in recognition of the need for predicting the life of coatings analytically, and non destructively; correspondingly, three principal tasks were established. Task 1, with the objective of analytically developing stress, strain and temperature distributions in the bucket and thereby predicting thermal fatigue (TMF) damage for various operating conditions; Task 2 with the objective of developing eddy current techniques to measure both TMF damage and general degradation of coatings and, Task 3, with the objective of developing mechanism based algorithms. This report is a record of the progress to date on these 3 key tasks. Two supporting tasks relating to field validation (Task 4) and economic analysis (Task 5) have not yet been initiated.

R. Viswanathan; K. Krzywosz; S. Cheruvu; E. Wan

2002-08-09T23:59:59.000Z

467

Development of Thin Section Zinc Die Casting Technology  

SciTech Connect

A new high fluidity zinc high pressure die casting alloy, termed the HF alloy, was developed during laboratory trials and proven in industrial production. The HF alloy permits castings to be achieved with section thicknesses of 0.3 mm or less. Technology transfer activities were conducted to develop usage of the HF high fluidity alloy. These included production of a brochure and a one-hour webinar on the HF alloy. The brochure was then sent to 1,184 product designers in the Interzinc database. There was excellent reception to this mailing, and from this initial contact 5 technology transfer seminars were conducted for 81 participants from 30 companies across a wide range of business sectors. Many of the successful applications to date involve high quality surface finishes. Design and manufacturing assistance was given for development of selected applications.

Goodwin, Frank [International Lead Zinc Research Org., Inc.] [International Lead Zinc Research Org., Inc.

2013-10-31T23:59:59.000Z

468

Section III, Division 5 - Development and Future Directions  

SciTech Connect

This paper provides commentary on a new division under Section III of the ASME Boiler and Pressure Vessel (BPV) Code. This new Division 5 has an issuance date of November 1, 2011 and is part of the 2011 Addenda to the 2010 Edition of the BPV Code. The new Division covers the rules for the design, fabrication, inspection and testing of components for high temperature nuclear reactors. Information is provided on the scope and need for Division 5, the structure of Division 5, where the rules originated, the various changes made in finalizing Division 5, and the future near-term and long-term expectations for Division 5 development. Portions of this paper were based on Chapter 17 of the Companion Guide to the ASME Boiler & Pressure Vessel Code, Fourth Edition, ASME, 2012, Reference.

D. K. Morton; R I Jetter; James E Nestell; T. D. Burchell; T L (Sam) Sham

2012-07-01T23:59:59.000Z

469

Thermal Performance of the LHC Short Straight Section Cryostat  

E-Print Network (OSTI)

The LHC Short Straight Section (SSS) cryostat houses and thermally protects in vacuum the cold mass which contains a twin-aperture superconducting quadrupole magnet and superconducting corrector magnets operating at 1.9 K in superfluid helium. In addition to mechanical requirements, the cryostat is designed to minimize the heat in-leak from the ambient temperature to the cold mass. Mechanical components linking the cold mass to the vacuum vessel such as support posts and an insulation vacuum barrier are designed to have minimum heat conductivity with efficient thermalisations for heat interception. Heat in-leak by radiation is reduced by employing multilayer insulation wrapped around the cold mass and an actively cooled aluminium thermal shield. The recent commissioning and operation of two SSS prototypes in the LHC Test String 2 have given a first experimental validation of the thermal performance of the SSS cryostat in nominal operating conditions. Temperature sensors mounted in critical locations provide a...

Bergot, J B; Nielsen, L; Parma, Vittorio; Rohmig, P; Roy, E

2002-01-01T23:59:59.000Z

470

AFCI-2.0 Library of Neutron Cross Section Covariances  

SciTech Connect

Neutron cross section covariance library has been under development by BNL-LANL collaborative effort over the last three years. The primary purpose of the library is to provide covariances for the Advanced Fuel Cycle Initiative (AFCI) data adjustment project, which is focusing on the needs of fast advanced burner reactors. The covariances refer to central values given in the 2006 release of the U.S. neutron evaluated library ENDF/B-VII. The preliminary version (AFCI-2.0beta) has been completed in October 2010 and made available to the users for comments. In the final 2.0 release, covariances for a few materials were updated, in particular new LANL evaluations for {sup 238,240}Pu and {sup 241}Am were adopted. BNL was responsible for covariances for structural materials and fission products, management of the library and coordination of the work, while LANL was in charge of covariances for light nuclei and for actinides.

Herman, M.; Herman,M.; Oblozinsky,P.; Mattoon,C.; Pigni,M.; Hoblit,S.; Mughabghab,S.F.; Sonzogni,A.; Talou,P.; Chadwick,M.B.; Hale.G.M.; Kahler,A.C.; Kawano,T.; Little,R.C.; Young,P.G.

2011-06-26T23:59:59.000Z

471

GRR/Section 3-NV-b - State Land Access | Open Energy Information  

Open Energy Info (EERE)

NV-b - State Land Access < GRR Jump to: navigation, search GRR-logo.png GEOTHERMAL REGULATORY ROADMAP Roadmap Home Roadmap Help List of Sections Section 3-NV-b - State Land Access...

472

EIS-0391-FEIS-Volume3-Section_1-2-2012  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

SECTION 1 SECTION 1 OVERVIEW OF THE PUBLIC COMMENT PROCESS 1-1 SECTION 1 OVERVIEW OF THE PUBLIC COMMENT PROCESS This section of this Comment-Response Document (CRD) describes the public comment process for the Draft Tank Closure and Waste Management Environmental Impact Statement for the Hanford Site, Richland, Washington (Draft TC & WM EIS) and the procedures used to respond to public comments. Section 1.1 summarizes the organization of this CRD. Section 1.2 discusses the public comment process and the means through which comments on the draft environmental impact statement (EIS) were received and addressed. Section 1.3 describes the public hearings on the Draft TC & WM EIS, including hearing locations and dates. Section 1.4 notes the role of the cooperating agencies.

473

Contract DE-AC36-99GO10337, Modification M098, Section J List...  

NLE Websites -- All DOE Office Websites (Extended Search)

Case by case Appendix A Section 3.5.a Compensation Increase Plan Plan Prior to each salary program year Appendix A Section 3.5.b. Provide for Contracting Officer approval a copy...

474

Eliassen-Palm Cross Sections for the Northern and Southern Hemispheres  

Science Conference Proceedings (OSTI)

Eliassen-Palm cross sections and residual meridional circulations are presented for the Northern and Southern Hemispheres for summer and winter based on the data of Newell et al. (1972, 1974). The cross sections are similar to those presented by ...

David J. Karoly

1982-01-01T23:59:59.000Z

475

Australasian Section of the American Oil Chemists' Society (AAOCS) Biennial Conference  

Science Conference Proceedings (OSTI)

2013 Archive of the Australasian Section of the American Oil Chemists' Society (AAOCS)Biennial Conference Australasian Section of the American Oil Chemists' Society (AAOCS) Biennial Conference Newcastle, New South Wales, Australia Australasian Se

476

GRR/Section 9-OR-a - State Environmental Process | Open Energy...  

Open Energy Info (EERE)

9-OR-a - State Environmental Process < GRR Jump to: navigation, search GRR-logo.png GEOTHERMAL REGULATORY ROADMAP Roadmap Home Roadmap Help List of Sections Section 9-OR-a - State...