Powered by Deep Web Technologies
Note: This page contains sample records for the topic "ah rated pack" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


1

Battery pack  

Science Conference Proceedings (OSTI)

A battery pack is described, having a center of mass, for use with a medical instrument including a latch, an ejector, and an electrical connector, the battery pack comprising: energy storage means for storing electrical energy; latch engagement means, physically coupled to the energy storage means, for engaging the latch; ejector engagement means, physically coupled to the energy storage means, for engaging the ejector; and connector engagement means, physically coupled to the energy storage means, for engaging the connector, the latch engagement means, ejector engagement means, and connector engagement means being substantially aligned in a plane offset from the center of mass of the battery pack.

Weaver, R.J.; Brittingham, D.C.; Basta, J.C.

1993-07-06T23:59:59.000Z

2

AOCS Official Method Ah 1-72  

Science Conference Proceedings (OSTI)

Aflatoxins AOCS Official Method Ah 1-72 Methods Methods and Analyses Analytical Chemistry Methods Downloads DEFINITION This method determines aflatoxins B 1 , B 2 , G 1 , and G 2...

3

Electronically configured battery pack  

DOE Green Energy (OSTI)

Battery packs for portable equipment must sometimes accommodate conflicting requirements to meet application needs. An electronically configurable battery pack was developed to support two highly different operating modes, one requiring very low power consumption at a low voltage and the other requiring high power consumption at a higher voltage. The configurable battery pack optimizes the lifetime and performance of the system by making the best use of all available energy thus enabling the system to meet its goals of operation, volume, and lifetime. This paper describes the cell chemistry chosen, the battery pack electronics, and tradeoffs made during the evolution of its design.

Kemper, D.

1997-03-01T23:59:59.000Z

4

AH Bolte A S | Open Energy Information  

Open Energy Info (EERE)

AH Bolte A S AH Bolte A S Jump to: navigation, search Name AH Bolte A/S Place Bjert, Denmark Zip DK-6091 Sector Wind energy Product Suppliers of flanges to the wind turbine industry. Coordinates 56.470699°, 8.77293° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":56.470699,"lon":8.77293,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

5

Slimhole frac pack tools overcome erosion problems  

SciTech Connect

The application of frac pack technology for stimulation and sand control in the Gulf of Mexico`s unconsolidated formations has steadily increased during the past several years. In addition, re-entry drilling has been one of the fastest growing development techniques used by operators for optimizing reservoir productivity. As such, smaller casing sizes are becoming more common in oil and gas producing wells. Gravel pack tools were being used for frac packing in 7-in. casing sizes and larger, but no tools were available to frac pack in the smaller 5-in. and 5{1/2}-in. casing. The erosion problems operators were experiencing in 7-in. gravel pack tools heightened concerns about fracturing through 5-in. tools with even smaller flow areas. Flow cutting in the 7-in. tools was so severe that it caused fluid communication between the gravel pack ports and the return flow holes in the crossover tool. This allowed fluid and proppant to return to the annulus above the packer, which could cause possible early screen-out and sticking of the crossover tool. The flow cutting could also reduce the tool`s pressure and tensile ratings. Any one of these problems could jeopardize the success of the frac pack operation. Therefore, an erosion resistant crossover tool for slimhole casing was developed to address these problems and optimize frac pack success.

Stout, G. [BJ Services, Tomball, TX (United States). Research and Development Center; Matte, T. [BJ Services, Lafayette, LA (United States); Rogers, B. [Marathon Oil Co., Lafayette, LA (United States)

1997-04-01T23:59:59.000Z

6

Graphitic packing removal tool  

DOE Patents (OSTI)

Graphitic packing removal tools are described for removal of the seal rings in one piece from valves and pumps. The packing removal tool has a cylindrical base ring the same size as the packing ring with a surface finish, perforations, knurling or threads for adhesion to the seal ring. Elongated leg shanks are mounted axially along the circumferential center. A slit or slits permit insertion around shafts. A removal tool follower stabilizes the upper portion of the legs to allow a spanner wrench to be used for insertion and removal.

Meyers, K.E.; Kolsun, G.J.

1996-12-31T23:59:59.000Z

7

Rigidity of packings  

Science Conference Proceedings (OSTI)

In Ludwig Danzer's Habilitatiionsschrift [L. Danzer, Endliche Punktmengen auf der 2-Sphare mit moglichst grossem minimalabstand, Habilitationsschrift, Gottingen, 1963] he initiated a study of the local nature of the packings from the point of view of ...

Robert Connelly

2008-11-01T23:59:59.000Z

8

Packing sets of patterns  

Science Conference Proceedings (OSTI)

Packing density is a permutation occurrence statistic which describes the maximal number of permutations of a given type that can occur in another permutation. In this article we focus on containment of sets of permutations. Although this question has ...

Alexander Burstein; Peter Hst

2010-01-01T23:59:59.000Z

9

Women @ Energy: Hai Ah Nam | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Hai Ah Nam Hai Ah Nam Women @ Energy: Hai Ah Nam April 1, 2013 - 11:04am Addthis Hai Ah Nam being interviewed on how the Titan supercomputer will benefit research in low-energy nuclear physics. The full video can be seen at https://www.olcf.ornl.gov/titan/. Hai Ah Nam being interviewed on how the Titan supercomputer will benefit research in low-energy nuclear physics. The full video can be seen at https://www.olcf.ornl.gov/titan/. Check out other profiles in the Women @ Energy series and share your favorites on Pinterest. Dr. Hai Ah Nam is a computational nuclear physicist working at the Oak Ridge Leadership Computing Facility at Oak Ridge National Laboratory (ORNL) since 2008. Hai Ah's research focuses on using cutting-edge high performance computing systems like Titan, the world's fastest

10

Optimization of blended battery packs  

E-Print Network (OSTI)

This thesis reviews the traditional battery pack design process for hybrid and electric vehicles, and presents a dynamic programming (DP) based algorithm that eases the process of cell selection and pack design, especially ...

Erb, Dylan C. (Dylan Charles)

2013-01-01T23:59:59.000Z

11

Packed Bed Combustion: An Overview  

E-Print Network (OSTI)

Packed Bed Combustion: An Overview William Hallett Dept. of Mechanical Engineering Université d'Ottawa - University of Ottawa #12;Packed Bed Combustion - University of Ottawa - CICS 2005 Introduction air fuel feedproducts xbed grate Packed Bed Combustion: fairly large particles of solid fuel on a grate, air supplied

Hallett, William L.H.

12

Alternative A(H1N1) suspects management  

Science Conference Proceedings (OSTI)

This paper deals with the differential diagnostics process behind the verdict of AH1N1 infection or not for the swine flu suspects. The application was designed as a support for doctors was built with ASP.NET 3.5 technology, the broad spectrum development ... Keywords: A(H1N1), application, charts, diagnostic, management

Dan Adrian Marior; Radu Zglimbea; Constantin Crciumaru

2010-08-01T23:59:59.000Z

13

Superdense Crystal Packings of Ellipsoids  

E-Print Network (OSTI)

Particle packing problems have fascinated people since the dawn of civilization, and continue to intrigue mathematicians and scientists. Resurgent interest has been spurred by the recent proof of Kepler's conjecture: the face-centered cubic lattice provides the densest packing of equal spheres with a packing fraction $\\phi\\approx0.7405$ \\cite{Kepler_Hales}. Here we report on the densest known packings of congruent ellipsoids. The family of new packings are crystal (periodic) arrangements of nearly spherically-shaped ellipsoids, and always surpass the densest lattice packing. A remarkable maximum density of $\\phi\\approx0.7707$ is achieved for both prolate and oblate ellipsoids with aspect ratios of $\\sqrt{3}$ and $1/\\sqrt{3}$, respectively, and each ellipsoid has 14 touching neighbors. Present results do not exclude the possibility that even denser crystal packings of ellipsoids could be found, and that a corresponding Kepler-like conjecture could be formulated for ellipsoids.

Aleksandar Donev; Frank H. Stillinger; P. M. Chaikin; Salvatore Torquato

2004-03-10T23:59:59.000Z

14

What to Pack for Mars  

E-Print Network (OSTI)

De Weck, O.L. What to Pack for Mars. Spectrum, IEEE 46.6 (2009): 39. 2009 Institute of Electrical and Electronics Engineers

De Weck, Olivier L.

15

Valve stem and packing assembly  

DOE Patents (OSTI)

A valve stem and packing assembly is provided in which a rotatable valve stem includes a first tractrix surface for sliding contact with a stem packing and also includes a second tractrix surface for sliding contact with a bonnet. Force is applied by means of a spring, gland flange, and gland on the stem packing so the stem packing seals to the valve stem and bonnet. This configuration serves to create and maintain a reliable seal between the stem packing and the valve stem. The bonnet includes a second complementary tractrix surface for contacting the second sliding tractrix surface, the combination serving as a journal bearing for the entire valve stem and packing assembly. The journal bearing so configured is known as a Schiele`s pivot. The Schiele`s pivot also serves to maintain proper alignment of the valve stem with respect to the bonnet. Vertical wear between the surfaces of the Schiele`s pivot is uniform at all points of contact between the second sliding tractrix surface and the second complementary tractrix surface of a bonnet. The valve stem is connected to a valve plug by means of a slip joint. The valve is opened and closed by rotating the valve stem. The slip joint compensates for wear on the Schiele`s pivot and on the valve plug. A ledge is provided on the valve bonnet for the retaining nut to bear against. The ledge prevents overtightening of the retaining nut and the resulting excessive friction between stem and stem packing.

Wordin, J.J.

1990-12-31T23:59:59.000Z

16

Test problems for quasi-satellite packing????  

E-Print Network (OSTI)

1. Test problems for quasi-satellite packing: Cylinders packing with behavior constraints and all the optimal solutions known. Chao Che. School of Mechanical ...

17

Valve stem and packing assembly  

SciTech Connect

A valve stem and packing assembly is provided in which a rotatable valve stem includes a first tractrix surface for sliding contact with a stem packing and also includes a second tractrix surface for sliding contact with a bonnet. Force is applied by means of a spring, gland flange, and gland on the stem packing so the stem packing seals to the valve stem and bonnet. This configuration serves to create and maintain a reliable seal between the stem packing and the valve stem. The bonnet includes a second complementary tractrix surface for contacting the second sliding tractrix surface, the combination serving as a journal bearing for the entire valve stem and packing assembly. The journal bearing so configured is known as a Schiele's pivot. The Schiele's pivot also serves to maintain proper alignment of the valve stem with respect to the bonnet. Vertical wear between the surfaces of the Schiele's pivot is uniform at all points of contact between the second sliding tractrix surface and the second complementary tractrix surface of a bonnet. The valve stem is connected to a valve plug by means of a slip joint. The valve is opened and closed by rotating the valve stem. The slip joint compensates for wear on the Schiele's pivot and on the valve plug. A ledge is provided on the valve bonnet for the retaining nut to bear against. The ledge prevents overtightening of the retaining nut and the resulting excessive friction between stem and stem packing.

Wordin, John J. (Bingham County, ID)

1991-01-01T23:59:59.000Z

18

Valve stem and packing assembly  

DOE Patents (OSTI)

A valve stem and packing assembly is provided in which a rotatable valve stem includes a first tractrix surface for sliding contact with a stem packing and also includes a second tractrix surface for sliding contact with a bonnet. Force is applied by means of a spring, gland flange, and gland on the stem packing so the stem packing seals to the valve stem and bonnet. This configuration serves to create and maintain a reliable seal between the stem packing and the valve stem. The bonnet includes a second complementary tractrix surface for contacting the second sliding tractrix surface, the combination serving as a journal bearing for the entire valve stem and packing assembly. The journal bearing so configured is known as a Schiele's pivot. The Schiele's pivot also serves to maintain proper alignment of the valve stem with respect to the bonnet. Vertical wear between the surfaces of the Schiele's pivot is uniform at all points of contact between the second sliding tractrix surface and the second complementary tractrix surface of a bonnet. The valve stem is connected to a valve plug by means of a slip joint. The valve is opened and closed by rotating the valve stem. The slip joint compensates for wear on the Schiele's pivot and on the valve plug. A ledge is provided on the valve bonnet for the retaining nut to bear against. The ledge prevents over tightening of the retaining nut and the resulting excessive friction between stem and stem packing. 2 figures.

Wordin, J.J.

1991-09-03T23:59:59.000Z

19

Valve stem and packing assembly  

DOE Patents (OSTI)

A valve stem and packing assembly is provided in which a rotatable valve stem includes a first tractrix surface for sliding contact with a stem packing and also includes a second tractrix surface for sliding contact with a bonnet. Force is applied by means of a spring, gland flange, and gland on the stem packing so the stem packing seals to the valve stem and bonnet. This configuration serves to create and maintain a reliable seal between the stem packing and the valve stem. The bonnet includes a second complementary tractrix surface for contacting the second sliding tractrix surface, the combination serving as a journal bearing for the entire valve stem and packing assembly. The journal bearing so configured is known as a Schiele's pivot. The Schiele's pivot also serves to maintain proper alignment of the valve stem with respect to the bonnet. Vertical wear between the surfaces of the Schiele's pivot is uniform at all points of contact between the second sliding tractrix surface and the second complementary tractrix surface of a bonnet. The valve stem is connected to a valve plug by means of a slip joint. The valve is opened and closed by rotating the valve stem. The slip joint compensates for wear on the Schiele's pivot and on the valve plug. A ledge is provided on the valve bonnet for the retaining nut to bear against. The ledge prevents overtightening of the retaining nut and the resulting excessive friction between stem and stem packing.

Wordin, J.J.

1990-01-01T23:59:59.000Z

20

Direct contact condensation of immiscible fluids in packed beds  

DOE Green Energy (OSTI)

An experimental study of a film type direct contact heat exchanger using immiscible fluids is made. Laboratory experiments were conducted on a R-113-water system using both 2.5 cm Berl saddles and 3.2 cm spheres as packing, in a 14.6 cm diameter column. The configuration was counter flow, with the vapor phase entering at the base of the column, and condensing on the laminar water film that coated the packing surface. Packing height, water temperature and both water and vapor flow rates were varied in obtaining heat transfer data. These and other packed bed heat transfer data published in the literature were reduced and correlated to yield a relationship between the Stanton number and the important vessel operating parameters.

Thomas, K.D.; Jacobs, H.R.; Boehm, R.F.

1978-11-01T23:59:59.000Z

Note: This page contains sample records for the topic "ah rated pack" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


21

RATES  

NLE Websites -- All DOE Office Websites (Extended Search)

Marketing > RATES Marketing > RATES RATES Current Rates Past Rates 2006 2007 2008 2009 2010 2011 2012 Rates Schedules Power CV-F13 CPP-2 Transmissions CV-T3 CV-NWT5 PACI-T3 COTP-T3 CV-TPT7 CV-UUP1 Ancillary CV-RFS4 CV-SPR4 CV-SUR4 CV-EID4 CV-GID1 Future and Other Rates SNR Variable Resource Scheduling Charge FY12-FY16 (October 1, 2012) SNR Rates Process Calendar (PDF - 171K) Procedures Informal Process Transmission Action Items List (PDF - 144K) Power Action Item List updated on 4-27-10 (PDF - 155K) Power Action Item List (Quick links to relevant documents) Formal Process Rates Brochure (01/11/2011) (PDF - 900K) Appendix A - Federal Register Notice (01/03/2011) (PDF - 8000K) Appendix B - Central Valley Project Power Repayment Study (PDF - 22,322K) Appendix C - Development of the CVP Cost of Service Study (PDF - 2038K)

22

RATES  

NLE Websites -- All DOE Office Websites (Extended Search)

Planning & Projects Planning & Projects Power Marketing Rates You are here: SN Home page > Power Marketing > RATES Rates and Repayment Services Rates Current Rates Power Revenue Requirement Worksheet (FY 2014) (Oct 2013 - Sep 2014) (PDF - 30K) PRR Notification Letter (Sep 27, 2013) (PDF - 959K) FY 2012 FP% True-Up Calculations(PDF - 387K) Variable Resource Scheduling Charge FY12-FY16 (October 1, 2012) PRR Forecast FY14-FY17 (May 23, 2013) (PDF - 100K) Forecasted Transmission Rates (May 2013) (PDF - 164K) Past Rates 2013 2012 2011 2010 2009 Historical CVP Transmission Rates (April 2013) (PDF - 287K) Rate Schedules Power - CV-F13 - CPP-2 Transmission - CV-T3 - CV-NWT5 - PACI-T3 - COTP-T3 - CV-TPT7 - CV-UUP1 Ancillary - CV-RFS4 - CV-SPR4 - CV-SUR4 - CV-EID4 - CV-GID1 Federal Register Notices - CVP, COTP and PACI

23

RATES  

NLE Websites -- All DOE Office Websites (Extended Search)

RATES RATES Rates Document Library SNR Rates Process Calendar (PDF - 171K) Procedures Informal Process Transmission Action Items List (PDF - 144K) Power Action Item List updated on 4-27-10 (PDF - 155K) Power Action Item List (Quick links to relevant documents) Formal Process Rates Brochure (01/11/2011) (PDF - 900K) Appendix A - Federal Register Notice (01/03/2011) (PDF - 8000K) Appendix B - Central Valley Project Power Repayment Study (PDF - 22,322K) Appendix C - Development of the CVP Cost of Service Study (PDF - 2038K) Appendix D - Western Transmission System Facilities Map (PDF - 274K) Appendix E - Estimated FY12 FP and BR Customer (PDF - 1144K) Appendix F - Forecasted Replacements and Additions FY11 - FY16 (PDF - 491K) Appendix G - Definitions (PDF - 1758K) Appendix H - Acronyms (PDF - 720K)

24

Kold Pack: Order (2013-CE-5323)  

Energy.gov (U.S. Department of Energy (DOE))

DOE ordered Kold Pack, Inc. to pay a $8,000 civil penalty after finding Kold Pack had failed to certify that certain models of walk-in cooler and freezer components comply with the applicable energy conservation standards.

25

Gravel packing method and apparatus  

Science Conference Proceedings (OSTI)

A method is described of gravel packing a well formation intersected by a well bore, the method comprising: forming a gel for transporting solids; mixing the solids with the gel; pumping the gel and solids mixed through a tool string disposed in the well bore to a subterranean position above the formation; pumping a breaker fluid to the subterranean position through an annulus breaker between the tool string and the wall of the well bore; introducing the breaker fluid into the tool string at the subterranean position and mixing the breaker fluid with the gel and solids whereby the gel is broken into a low viscosity fluid; and transporting the resultant low viscosity fluid and solids mixed to the formation for packing.

Bolin, M.L.

1987-05-05T23:59:59.000Z

26

Pack Cementation Aluminizing of Steels  

Science Conference Proceedings (OSTI)

Table 3   Partial list of commercial applications of pack cementation aluminizing...Carbon and stainless steels Steam power and cogeneration Waterwall tubes 2 % Cr-1% Mo steel Fluidized bed combustor tubes 2 % Cr-1% Mo steel Waste heat boiler tubes Carbon steel Economizer and air preheater tubes 2 % Cr-1% Mo steel Superheater tubes 2 % Cr-1% Mo steel Aerospace (a) Turbine blades...

27

Purifying Decane A. Prepare Packing Material  

E-Print Network (OSTI)

to prevent escape of packing material. 4. Seal bottom of column and fill column with packing material to the remaining space at the top of the column. 2. Seal top of column and connect to nitrogen tank. Set with decane. Note: Never allow top of packing material to contact the air after it has been wetted by decane 4

Buckley, Jill S.

28

Jammed Packings of Hard Particles Aleksandar Donev  

E-Print Network (OSTI)

of disordered and ordered hard-sphere and hard-ellipsoid packings. In the first part of this dissertation-equilibrium) free energy of nearly jammed packings of hard particles is designed and implemented. In the second partJammed Packings of Hard Particles Aleksandar Donev A Dissertation Presented to the Faculty

Mohri, Mehryar

29

Packing microstructure and local density variations of experimental and computational pebble beds  

Science Conference Proceedings (OSTI)

In pebble bed type nuclear reactors the fuel is contained in graphite pebbles, which form a randomly stacked bed with a non-uniform packing density. These variations can influence local coolant flow and power density and are a possible cause of hotspots. To analyse local density variations computational methods are needed that can generate randomly stacked pebble beds with a realistic packing structure on a pebble-to-pebble level. We first compare various properties of the local packing structure of a computed bed with those of an image made using computer aided X-ray tomography, looking at properties in the bulk of the bed and near the wall separately. Especially for the bulk of the bed, properties of the computed bed show good comparison with the scanned bed and with literature, giving confidence our method generates beds with realistic packing microstructure. Results also show the packing structure is different near the wall than in the bulk of the bed, with pebbles near the wall forming ordered layers similar to hexagonal close packing. Next, variations in the local packing density are investigated by comparing probability density functions of the packing fraction of small clusters of pebbles throughout the bed. Especially near the wall large variations in local packing fractions exists, with a higher probability for both clusters of pebbles with low (0.65) packing fraction, which could significantly affect flow rates and, together with higher power densities, could result in hotspots. (authors)

Auwerda, G. J.; Kloosterman, J. L.; Lathouwers, D.; Van Der Hagen, T. H. J. J. [Delft Univ. of Technology, Mekelweg 15, 2629 JB, Delft (Netherlands)

2012-07-01T23:59:59.000Z

30

The Packing of Granular Polymer Chains  

SciTech Connect

Rigid particles pack into structures, such as sand dunes on the beach, whose overall stability is determined by the average number of contacts between particles. However, when packing spatially extended objects with flexible shapes, additional concepts must be invoked to understand the stability of the resulting structure. Here, we examine the disordered packing of chains constructed out of flexibly connected hard spheres. Using x-ray tomography, we find that long chains pack into a low-density structure whose mechanical rigidity is mainly provided by the backbone. On compaction, randomly oriented, semi-rigid loops form along the chain, and the packing of chains can be understood as the jamming of these elements. Finally, we uncover close similarities between the packing of chains and the glass transition in polymers.

Zou, Ling-Nan; Cheng, Xiang; Rivers, Mark L.; Jaeger, Heinrich M.; Nagel, Sidney R.; UC

2009-12-01T23:59:59.000Z

31

Geometrical Properties of Simulated Packings of Spherocylinders  

Science Conference Proceedings (OSTI)

In a wide range of industrial applications there appear systems of hard particles of different shapes and sizes, known as "packings". In this work, the force-biased algorithm, primarily designed to model close packings of equal spheres, is adapted to ...

Monika Bargie?

2008-06-01T23:59:59.000Z

32

VripPack User's Guide Brian Curless  

E-Print Network (OSTI)

and compiling vrip is fairly straightforward. VripPack depends on Tcl/Tk being installed and has been compiled most recently against Tcl/Tk version 8.4. VripPack comes with these libraries for Linux, but you may. The following web page is a good reference for installing Cygwin and Tcl/Tk as needed for vrip: http

Davis, James E.

33

Method for gravel packing wells  

SciTech Connect

This patent describes a method for gravel packing a well that penetrates an unconsolidated or poorly consolidated subterranean oil or gas reservoir. It comprises: providing a borehole casing through the reservoir; perforating the casing at preselected intervals therealong to form at least one set of longitudinal, perforation tunnels adjacent a substantial portion of the reservoir; locating a sand screen inside the casing and in juxtaposition with the perforation tunnels, an annulus being formed between the sand screen and the casing; positioning a conduit in juxtaposition with the sand screen extending substantially the length of the sand screen and having its upper extremity open to fluids; injecting a fluid slurry containing gravel down through the annulus and conduit whereby the fluid portion of the slurry is forced out of the annulus through the perforation tunnels into the reservoir and the gravel portion of the slurry deposited in the annulus and forced into the perforation tunnels into the formation; sizing the cross-sectional area of the conduit and the annulus so that if gravel forms a bridge in a portion of the annulus thereby blocking the flow of fluid slurry through the the annulus, fluid slurry containing gravel will continue to flow through the conduit and into the annulus around the gravel bridge; and terminating the injection of the slurry.

Jones, L.G.

1990-08-07T23:59:59.000Z

34

Compost Bedded Pack Barns: Management Practices and Economic Implications.  

E-Print Network (OSTI)

??Compost bedded pack (CBP) barn design and pack maintenance procedures vary considerably, making advising and problem-solving challenging. One objective of this research was to characterize (more)

Black, Randi Alyson

2013-01-01T23:59:59.000Z

35

Kold Pack: Proposed Penalty (2013-CE-5323)  

Energy.gov (U.S. Department of Energy (DOE))

DOE alleged in a Notice of Proposed Civil Penalty that Kold Pack, Inc. failed to certify walk-in cooler or freezer components as compliant with the energy conservation standards.

36

Groundwater well with reactive filter pack  

DOE Patents (OSTI)

A method and apparatus for the remediation of contaminated soil and ground water wherein a reactive pack material is added to the annular fill material utilized in standard well construction techniques.

Gilmore, Tyler J. (Pasco, WA); Holdren, Jr., George R. (Kennewick, WA); Kaplan, Daniel I. (Richland, WA)

1998-01-01T23:59:59.000Z

37

test problem for packing_sumit  

E-Print Network (OSTI)

Test problems of circles in circle packing with constraints and known the optimal solutions*. Hong-fei Teng1, 2**, Chao Che 2, Yu Chen 1, Yi-shou Wang 1. 1.

38

On universal structural characteristics of granular packs  

E-Print Network (OSTI)

Understanding the dependence of the structure of granular materials on grain parameters is key to predictive modelling of granular matter. Structural characteristics are commonly believed to be sensitive, for a given packing process, to intergranular friction, particle size distribution and initial conditions. We show here that the intergranular friction coefficient and the initial conditions are details, which can be scaled away, and that structures are determined mainly by the packing dynamics and the grain size distribution. This we do using the quadron description to analyse the structures of a number of numerically-generated planar disc packs in mechanical equilibrium, varying all these parameters. Our findings are as follows. 1. The mean coordination number is a universal function of the packing fraction, independent of the initial conditions, intergranular friction and size distribution we used, when "rattlers" are ignored. 2. For a given packing process and disc size distribution, both the total and conditional quadron volume distributions collapse to universal forms, independent of the initial conditions and intergranular friction. 3. The cell order distribution collapses to a universal form for all friction coefficients, initial conditions and for the two disc size distributions we studied. These results suggest that mechanically stable granular structures are determined mainly by the packing dynamics and the grains size / shape distributions - the effects of the intergranular friction and initial state can be scaled away and are therefore predictable.

Takashi Matsushima; Raphael Blumenfeld

2013-05-27T23:59:59.000Z

39

Method for packed column separations and purifications  

DOE Patents (OSTI)

The invention encompasses a method of packing and unpacking a column chamber. A mixture of a fluid and a matrix material are introduced through a column chamber inlet so that the matrix material is packed within a column chamber to form a packed column. The column chamber having the column chamber inlet or first port for receiving the mixture further has an outlet port and an actuator port. The outlet port is partially closed for capturing the matrix material and permitting the fluid to flow therepast by rotating relative one to the other of a rod placed in the actuator port. Further rotation relative one to the other of the rod and the column chamber opens the outlet and permits the matrix material and the fluid to flow therethrough thereby unpacking the matrix material from the column chamber.

Holman, David A. (Richland, WA); Bruckner-Lea, Cynthia J. (Richland, WA); Brockman, Fred J. (Kennewick, WA); Chandler, Darrell P. (Richland, WA)

2006-08-15T23:59:59.000Z

40

Geometric packing under non-uniform constraints  

Science Conference Proceedings (OSTI)

We study the problem of discrete geometric packing. Here, given weighted regions (say in the plane) and points (with capacities), one has to pick a maximum weight subset of the regions such that no point is covered more than its capacity. We provide ... Keywords: independent set, optimization, rounding scheme

Alina Ene; Sariel Har-Peled; Benjamin Raichel

2012-06-01T23:59:59.000Z

Note: This page contains sample records for the topic "ah rated pack" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


41

Vehicle Details And Battery Specifications  

NLE Websites -- All DOE Office Websites (Extended Search)

System Voltage: 355.2 V Number of Electric Machines 2 : 2 Rated Pack Capacity: 45 Ah Motor: 111 kW (peak), AC induction, Air cooled Rated Pack Energy: 16.5 kWh Generator 2 :...

42

Functional and phenotypic effects of AhR activation in inflammatory dendritic cells  

SciTech Connect

Aryl hydrocarbon receptor (AhR) activation by 2,3,7,8-tetrachlorodibenzo-p-dioxin (TCDD) induces immune suppression. Dendritic cells (DCs) are key antigen presenting cells governing T cell activation and differentiation. However, the consequences of AhR activation in DCs are not fully defined. We hypothesized that AhR activation alters DC differentiation and generates dysfunctional DCs. To test this hypothesis, inflammatory bone marrow-derived DCs (BMDCs) from C57Bl/6 mice were generated in the presence of vehicle or TCDD. TCDD decreased CD11c expression but increased MHC class II, CD86 and CD25 expression on the BMDCs. The effects of TCDD were strictly AhR-dependent but not exclusively DRE-mediated. Similar effects were observed with two natural AhR ligands, 6-formylindolo[3,2-b]carbazole (FICZ) and 2-(1H-Indol-3-ylcarbonyl)-4-thiazolecarboxylic acid (ITE). TCDD increased LPS- and CpG-induced IL-6 and TNF-{alpha} production by BMDCs but decreased their NO production. TCDD decreased CpG-induced IL-12p70 production by BMDCs but did not affect their secretion of IL-10. TCDD downregulated LPS- and CpG-induced NF-kB p65 levels and induced a trend towards upregulation of RelB levels in the BMDCs. AhR activation by TCDD modulated BMDC uptake of both soluble and particulate antigens. Induction of indoleamine-2,3-dioxygenase (IDO) and TGF-{beta}3 has been implicated in the generation of regulatory T cells following AhR activation. TCDD increased IDO1, IDO2 and TGF-{beta}3 mRNA levels in BMDCs as compared to vehicle. Despite the induction of regulatory mediators, TCDD-treated BMDCs failed to suppress antigen-specific T cell activation. Thus, AhR activation can directly alter the differentiation and innate functions of inflammatory DCs without affecting their ability to successfully interact with T cells.

Bankoti, Jaishree [Department of Biomedical and Pharmaceutical Sciences, University of Montana, Missoula, MT (United States); Center for Environmental Health Sciences, University of Montana, Missoula, MT (United States); Rase, Ben [Center for Environmental Health Sciences, University of Montana, Missoula, MT (United States); Simones, Tom [Department of Biomedical and Pharmaceutical Sciences, University of Montana, Missoula, MT (United States); Center for Environmental Health Sciences, University of Montana, Missoula, MT (United States); Shepherd, David M., E-mail: david.shepherd@umontana.ed [Department of Biomedical and Pharmaceutical Sciences, University of Montana, Missoula, MT (United States); Center for Environmental Health Sciences, University of Montana, Missoula, MT (United States)

2010-07-15T23:59:59.000Z

43

The dissolution rates of natural glasses as a function of their composition at pH 4 and 10.6  

E-Print Network (OSTI)

1995) Chemical weathering rates of pyroxenes and amphibols.In Chemical weathering rates of silicate minerals (eds. A.H. (1999) Field weathering rates of Mt. St. Helens tephra.

Wolff-Boenisch, Domenik

2004-01-01T23:59:59.000Z

44

Probe with integrated heater and thermocouple pack  

DOE Patents (OSTI)

A probe for measuring heat includes an elongate rod fitted within a sheath, and a plurality of annular recesses are formed on the surface of the rod in a spaced-apart relationship to form annular chambers that are resistant to heat flow. A longitudinal bore extends axially into the rod and within the cylinders defined by the annular chambers, and an integrated heater and thermocouple pack is dimensioned to fit within the bore. In construction, the integrated pack includes a plurality of wires disposed in electrical insulation within a sheath and a heater cable. These wires include one common wire and a plurality of thermocuple wires. The common wire is constructed of one type of conductive material while the thermocouple wires are each constructed of two types of materials so that at least one thermocouple junction is formed therein. All of the wires extend the length of the integrated pack and are connected together at their ends. The thermocouple wires are constructed to form thermocouple junctions proximate to each annular chamber for producing electromotive forces corresponding to the temperature of the rod within the annular chambers relative to outside the chambers. In the preferred embodiment, each thermocouple wire forms two thermocouple junctions, one junction being disposed within an annular chamber and the second junction being disposed outside of, but proximate to, the same annular chamber. In one embodiment two thermocouple wires are configured to double the sensitivity of the probe in one region.

McCulloch, Reg W. (Oak Ridge, TN); Dial, Ralph E. (Concord, TN); Finnell, Wilber K. R. (Kingston, TN)

1990-01-01T23:59:59.000Z

45

Probe with integrated heater and thermocouple pack  

DOE Patents (OSTI)

A probe for measuring heat includes an elongate rod fitted within a sheath, and a plurality of annular recesses are formed on the surface of the rod in a spaced-apart relationship to form annular chambers that are resistant to heat flow. A longitudinal bore extends axially into the rod and within the cylinders defined by the annular chambers, and an integrated heater and thermocouple pack is dimensioned to fit within the bore. In construction, the integrated pack includes a plurality of wires disposed in electrical insulation within a sheath and a heater cable. These wires include one common wire and a plurality of thermocouple wires. The common wire is constructed of one type of conductive material while the thermocouple wires are each constructed of two types of materials so that at least one thermocouple junction is formed therein. All of the wires extend the length of the integrated pack and are connected together at their ends. The thermocouple wires are constructed to form thermocouple junctions proximate to each annular chamber for producing electromotive forces corresponding to the temperature of the rod within the annular chambers relative to outside the chambers. In the preferred embodiment, each thermocouple wire forms two thermocouple junctions, one junction being disposed within an annular chamber and the second junction being disposed outside of, but proximate to, the same annular chamber. In one embodiment two thermocouple wires are configured to double the sensitivity of the probe in one region.

McCulloch, Reginald W. (Oak Ridge, TN); Dial, Ralph E. (Concord, TN); Finnell, Wilber K. R. (Kingston, TN)

1988-01-01T23:59:59.000Z

46

Packed fluidized bed blanket for fusion reactor  

DOE Patents (OSTI)

A packed fluidized bed blanket for a fusion reactor providing for efficient radiation absorption for energy recovery, efficient neutron absorption for nuclear transformations, ease of blanket removal, processing and replacement, and on-line fueling/refueling. The blanket of the reactor contains a bed of stationary particles during reactor operation, cooled by a radial flow of coolant. During fueling/refueling, an axial flow is introduced into the bed in stages at various axial locations to fluidize the bed. When desired, the fluidization flow can be used to remove particles from the blanket.

Chi, John W. H. (Mt. Lebanon, PA)

1984-01-01T23:59:59.000Z

47

The Influence of Surface Chemistry on the Rate Capability of LiNi[subscript 0.5]Mn[subscript 0.5]O[subscript 2] for Lithium Rechargeable Batteries  

E-Print Network (OSTI)

Subsequent annealing at Formula enhances the rate capability of LiNi[subscript 0.5]Mn[subscript 0.5]O[subscript 2], delivering 180 mAh/g at 55[degrees]C and 8C rate compared to 50 mAh/g of LiNi[subscript 0.5]Mn[subscript ...

Yabuuchi, Naoaki

48

Open-cycle absorption cooling using packed-bed absorbent reconcentration  

DOE Green Energy (OSTI)

The technical feasibility of a lithium chloride open-cycle absorption air conditioner using solar-heated air for reconcentration of the absorbent solution is examined. In contrast to a successfully operating Soviet design (in which absorbent reconcentration is accomplished by trickling the solution across a sloping black roof exposed to the sun), this study involves a packed-bed concentrator. Solar-heated air reconcentrates the solution by vaporizing water (the refrigerant) from the solution in the packed bed, enabling the system to be incorporated into a conventional solar air heating system and avoiding numerous problems associated with the roof concentrator. A thermodynamic analysis provides the criteria for the design of the packed bed. Heat and mass transfer processes occurring simultaneously in the bed are modeled using an iterative technique with the aid of a digital computer. The size of the packed-bed required to reconcentrate the absorbent solution at a rate corresponding to 10,550 W of cooling is determined, using flow rates, temperatures, and humidities typical of residential solar air-heating systems. Based on these results, the system air conditioning capability with solar energy input is predicted over the course of a clear summer day for Fort Collins, Colorado, and St. Louis, Missouri. Sufficient cooling capacity to meet a 10,550 W peak load using a 70 m/sup 2/ flatplate collector array is predicted by the model for both locations.

Leboeuf, C. M.; Loef, G. O.G.

1980-05-01T23:59:59.000Z

49

Dense Packings of Superdisks and the Role of Symmetry  

E-Print Network (OSTI)

We construct the densest known two-dimensional packings of superdisks in the plane whose shapes are defined by |x^(2p) + y^(2p)| 0.5, with the circular-disk case p = 1) and concave-shaped particles (0 Donev, Torquato and Stillinger, J. Comput. Phys. 202 (2005) 737] suggest exact constructions of the densest known packings. We find that the packing density (covering fraction of the particles) increases dramatically as the particle shape moves away from the "circular-disk" point (p = 1). In particular, we find that the maximal packing densities of superdisks for certain p 6 = 1 are achieved by one of the two families of Bravais lattice packings, which provides additional numerical evidence for Minkowski's conjecture concerning the critical determinant of the region occupied by a superdisk. Moreover, our analysis on the generated packings reveals that the broken rotational symmetry of superdisks influences the packing characteristics in a non-trivial way. We also propose an analytical method to construct dense packings of concave superdisks based on our observations of the structural properties of packings of convex superdisks.

Y. Jiao; F. H. Stillinger; S. Torquato

2007-12-04T23:59:59.000Z

50

Minimizing formation damage during gravel pack operations  

Science Conference Proceedings (OSTI)

A method is described for minimizing formation damage caused by intrusive fluids prior to a gravel packing operation in loosely consolidated formations penetrated by at least one well. The method comprises: filling the casing of the well with an underbalanced completion fluid; placing within the well a removable packer capable of isolating the space between the casing and the formation from the downhole well pressure; setting through the packer a first tubing suitable for perforating and stabilizing the flow of fluids into the well; perforating the casing; and introducing a blocking agent into the formation via the perforations which agent upon solidification is sufficient to minimize formation damage by avoiding the introduction of formation fluids.

Jennings, A.R. Jr.

1987-05-12T23:59:59.000Z

51

Volatile Components from Packing Matrials, Rev. 2  

Science Conference Proceedings (OSTI)

An outgassing study was conducted on five packing materials, comprising two experiments. These materials comprised 277-4 borated concrete, Borobond4 concrete, polyethylene bags, silica-filled silicone rubber seals, and silicone foam padding. The purpose was measure the volume of gases which diffuse from packaging materials when sealed in containers. Two heating profiles were used to study the offgassing quantities in a set of accelerated aging tests. It was determined that the concretes contain a large quantity of water. The plastic materials hold much less moisture, with the silicone materials even consuming water, possibly due to the presence of silica filler. Polyethylene tends to degrade as the temperature is elevated and the foam stiffens.

Smith, R. A.

2006-03-01T23:59:59.000Z

52

Thermal vacancies in close-packing solids  

E-Print Network (OSTI)

Based on Stillinger's version of cell cluster theory, we derive an expression for the equilibrium concentration of thermal monovacancies in solids which allows for a transparent interpretation of the vacancy volume and the energetic/entropic part in the corresponding Gibbs energy of vacancy formation $\\Delta G_{\\rm v}$. For the close--packing crystals of the hard sphere and Lennard--Jones model systems very good agreement with simulation data is found. Application to metals through the embedded--atom method (EAM) reveals a strong sensitivity of the variation of $\\Delta G_{\\rm v}$ with temperature to details of the EAM potential. Our truncation of the cell cluster series allows for an approximate, but direct measurement of crystal free energies and vacancy concentration in colloidal model systems using laser tweezers.

Mostafa Mortazavifar; Martin Oettel

2013-11-20T23:59:59.000Z

53

A DC CIRCUIT BREAKER FOR AN ELECTRIC VEHICLE BATTERY PACK  

E-Print Network (OSTI)

A DC CIRCUIT BREAKER FOR AN ELECTRIC VEHICLE BATTERY PACK Geoff Walker Dept of Computer Science vehicle battery packs require DC circuit breakers for safety. These must break thousands of Amps DC at hundreds of Volts. The Sunshark solar racing car has a 140V 17Ahr battery box which needs such a breaker

Walker, Geoff

54

Packed bed reactor for photochemical .sup.196 Hg isotope separation  

DOE Patents (OSTI)

Straight tubes and randomly oriented pieces of tubing having been employed in a photochemical mercury enrichment reactor and have been found to improve the enrichment factor (E) and utilization (U) compared to a non-packed reactor. One preferred embodiment of this system uses a moving bed (via gravity) for random packing.

Grossman, Mark W. (Belmont, MA); Speer, Richard (Reading, MA)

1992-01-01T23:59:59.000Z

55

A Genetic Approach for Two Dimensional Packing with Constraints  

Science Conference Proceedings (OSTI)

In this paper, a new genetic algorithm based method is proposed for packing rectangular cargos of different sizes into a given loading area in a two dimensional framework. A novel penalty function method is proposed for checking the solution strings ... Keywords: genetic algorithm, penalty function, sentry point, two dimensional packing

Wee Sng Khoo; P. Saratchandran; N. Sundararajan

2001-05-01T23:59:59.000Z

56

Packing assembly for use in a plunger bore  

SciTech Connect

A packing assembly is described which is adapted to be installed in a machine, such as a pump, the machine having a housing with a plunger bore and a plunger therin to provide a fluid-tight seal for the machine. The assembly consists of: a packing gland which fastens into one end of the plunger bore; a packing gland spacer positioned adjacent to and in contact with the packing gland; a lubrication gland positioned adjacent to and in contact with the packing gland spacer; a separate stack of packing rings, which includes at least two packing rings, each ring in the stack has a front face defining a concave shape, a rear face defining a convex shape, and a groove, defining a concave shape, in the front face; a female adaptor ring positioned between the lubrication gland and the packing ring stack, the female adaptor ring has a front face with a concave shape, the concave shape defines an angle which substantially conforms to the angle defined by the convex shape of the rear face of the last packing ring in the stack, such that the front face of the female adaptor ring can seat firmly against the rear face of the last packing ring; a male-female adaptor ring positioned between two packing rings in the stack, the male-female adaptor ring has a front face and rear face, the rear face has a convex shape and an integral rib member defining a convex shape, on the rear face, and the front face has a concave shape; the convex shape of the rear face of the male-female adaptor ring defines an angle which substantially conforms to the angle defined by the concave shape of the front face of the last packing ring in the stack and the convex shape of the face of the last packing ring in the stack and the convex shape of the rib member substantially conforms to the concave shape of the groove in the front face of the last packing ring.

Cameron, D.C.; Cobb, H.V.; Winn, F.M.

1986-02-25T23:59:59.000Z

57

Improving the density of jammed disordered packings using ellipsoids  

E-Print Network (OSTI)

Packing problems, such as how densely objects can fill a volume, are among the most ancient and persistent problems in mathematics and science. For equal spheres, it has only recently been proved that the face-centered cubic lattice has the highest possible packing fraction ? = ? / ? 18 ? 0.74. It is also well-known that certain random (amorphous) jammed packings have ? ? 0.64. Here we show experimentally and with a new simulation algorithm that ellipsoids can randomly pack more densely; up to ? = 0.68 ? 0.71 for spheroids with an aspect ratio close to that of M&MS r?Candies, and even approach ? ? 0.74 for general ellipsoids. We suggest that the higher density is directly related to the higher number of degrees of freedom per particle and thus the larger number of particle contacts required to mechanically stabilize the packing. We support this by

Aleksandar Donev; Ibrahim Cisse; David Sachs; Evan A. Variano; Frank H. Stillinger; Robert Connelly; Salvatore Torquato; P. M. Chaikin

2004-01-01T23:59:59.000Z

58

Unconsolidated sand grain shape, size impact frac-pack design  

SciTech Connect

The shape and size of sand grains, as well as the saturating fluid, influence the mechanical properties of unconsolidated sands and need to be considered in frac-pack design. These mechanical properties of unconsolidated properties of unconsolidated sands play an important role in determining the geometry of frac-pack treatments. Stress-strain curves obtained for unconsolidated sands at elevated stresses show highly nonlinear hysteretic behavior. The impact of these findings on frac-pack design can be significant. The nonlinear elastic properties of unconsolidated sand can give rise to some unique features in the pressure response and in the fracture geometry that may not be observed in hard rocks. This article focuses on the impact of mechanical properties of poorly consolidated and unconsolidated sands on the geometry of frac packs. The paper discusses frac packs, mechanical properties (Young`s modulus, shear failure) and effective treatments.

Wang, E.; Sharma, M.M. [Univ. of Texas, Austin, TX (United States)

1997-05-19T23:59:59.000Z

59

Ring type dumped packing saving 30% on tower cost  

SciTech Connect

This article discusses the packing problems of a flue gas processing plant that recovers 90,000 lb/hr of carbon dioxide for use in an enhanced oil recovery (EOR) project. A concentrated absorption solution was needed to keep the liquid circulation low, and a packing with low pressure drop and high effective surface area was needed to keep the fan horsepower and column size down and minimize the amount of CO/sub 2/ that slips through the column. The solution was to use a high concentration CO/sub 2/ recovery solvent and a proprietary ring type packing was used which gives 50% less pressure drop than conventional packing and provides high efficiency. Carbon steel packing rings were used except for two sections.

Wiggins, W.R. III; Hodel, A.E.

1984-02-01T23:59:59.000Z

60

Influence of Particle Size Distribution on Random Close Packing  

E-Print Network (OSTI)

The densest amorphous packing of rigid particles is known as random close packing. It has long been appreciated that higher densities are achieved by using collections of particles with a variety of sizes. The variety of sizes is often quantified by the polydispersity of the particle size distribution: the standard deviation of the radius divided by the mean radius. Several prior studies quantified the increase of the packing density as a function of polydispersity. Of course, a particle size distribution is also characterized by its skewness, kurtosis, and higher moments, but the influence of these parameters has not been carefully quantified before. In this work, we numerically generate many packings with different particle radii distributions, varying polydispersity and skewness independently of one another. We find two significant results. First, the skewness can have a significant effect on the packing density and in some cases can have a larger effect than polydispersity. Second, the packing fraction is relatively insensitive to the value of the kurtosis. We present a simple empirical formula for the value of the random close packing density as a function of polydispersity and skewness.

Kenneth W. Desmond; Eric R. Weeks

2013-03-19T23:59:59.000Z

Note: This page contains sample records for the topic "ah rated pack" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


61

Co-combustion of textile residues with cardboard and waste wood in a packed bed  

SciTech Connect

The combustible fraction of the municipal waste is mostly bio-derived. Energy recovery of the wastes that cannot be economically recycled is a key part of sustainable energy policy and waste management. Textile residues have high energy content. When burned alone in a packed bed system, however, their combustion efficiency is low due to the irregular propagation of the ignition front and the low burning rates. In order to achieve more efficient combustion of textile residues, a series of co-combustion tests were carried out for various mixture compositions and air flow rates in a packed bed combustor. The combustion performance of these materials was evaluated by using quantitative measures such as ignition rate, burning rate and equivalence ratio. Co-combustion of textile residues with cardboard for a textile fraction of up to 30% achieved satisfactorily high burning rate and low unburned carbon content in the bottom ash. The mixture was more resistant to convective cooling by air, which significantly expanded the range of air flow rate for combustion at high burning rates. In co-combustion with a material that has a very low ignition front speed such as waste wood, the propagation of the ignition front was governed by textile residues. Therefore, the co-combustion of textile residues can be better performed with a material having similar ignition front speeds, in which the two materials simultaneously burn at the ignition front. (author)

Ryu, Changkook; Phan, Anh N; Sharifi, Vida N; Swithenbank, Jim [Sheffield University Waste Incineration Centre (SUWIC), Department of Chemical and Process Engineering, The University of Sheffield, Mappin Street, Sheffield S1 3JD (United Kingdom)

2007-11-15T23:59:59.000Z

62

Leaders of the Fuel Cell Pack | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Leaders of the Fuel Cell Pack Leaders of the Fuel Cell Pack Leaders of the Fuel Cell Pack February 17, 2012 - 10:32am Addthis Fuel cell forklifts like the one shown here are used by leading companies across the U.S. as part of their daily business operations. | Energy Department file photo. Fuel cell forklifts like the one shown here are used by leading companies across the U.S. as part of their daily business operations. | Energy Department file photo. Sunita Satyapal Program Manager, Hydrogen & Fuel Cell Technology Program What does the report show? The 34 companies profiled used more than 250 fuel cells totaling 30+ MW of stationary power -- enough to supply electricity for over 21,000 households. What do WalMart, Coca-Cola, Sysco, and Whole Foods have in common? They're leading the pack when it comes to hydrogen and fuel cells.

63

LEDS Collaboration in Action Workshop Participant Pack | Open Energy  

Open Energy Info (EERE)

source source History View New Pages Recent Changes All Special Pages Semantic Search/Querying Get Involved Help Apps Datasets Community Login | Sign Up Search Page Edit History Facebook icon Twitter icon » LEDS Collaboration in Action Workshop Participant Pack Jump to: navigation, search LEDSGP Logo.png Advancing climate-resilient low emission development around the world Home About Tools Expert Assistance Events Publications Join Us ACDS Workshop Participant Pack Agenda Accommodations Participants Location Arrival Form Open Space Sessions Speakers Presentations Links Contact Us Participant Pack Pack.pdf Powered by OpenEI ledsgp.org is built on the same platform as the popular Wikipedia site. Like Wikipedia, it is a "wiki" or website developed collaboratively by a community of users. Thanks to our unique relationship with OpenEI.org, you

64

Nanostructure and Nanomechanics of Cement: Polydisperse Colloidal Packing  

E-Print Network (OSTI)

Cement setting and cohesion are governed by the precipitation and growth of calcium-silicate-hydrate, through a complex evolution of microstructure. A colloidal model to describe nucleation, packing, and rigidity of ...

Masoero, Enrico

65

Frac packs: A specialty option or primary completion technique?  

SciTech Connect

High permeability fracture treatments have taken place at Alaska`s North Slope, in the North Sea, and most recently, in the unconsolidated Miocene formations of the Gulf of Mexico -- where gravel pack completions have historically been used to prevent sand production. In the Gulf of Mexico, attempts were made as early as the mid-1960s to hydraulically fracture sands. However, some of these early treatments failed because of improper techniques, poor candidate selection and lack of understanding of rock property mechanics. Recent developments in fracturing technology, and the use of this technology to fracture through damage has achieved more favorable results than gravel packing and sandstone acidizing, and has led to widespread use of these fracture treatments. The procedure for fracturing high permeability formations is called frac packing. These frac pack treatments are typically used to remove near-wellbore damage that occurs from drilling and completion operations.

NONE

1997-03-01T23:59:59.000Z

66

Leaders of the Fuel Cell Pack | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Leaders of the Fuel Cell Pack Leaders of the Fuel Cell Pack Leaders of the Fuel Cell Pack February 17, 2012 - 10:32am Addthis Fuel cell forklifts like the one shown here are used by leading companies across the U.S. as part of their daily business operations. | Energy Department file photo. Fuel cell forklifts like the one shown here are used by leading companies across the U.S. as part of their daily business operations. | Energy Department file photo. Sunita Satyapal Program Manager, Hydrogen & Fuel Cell Technology Program What does the report show? The 34 companies profiled used more than 250 fuel cells totaling 30+ MW of stationary power -- enough to supply electricity for over 21,000 households. What do WalMart, Coca-Cola, Sysco, and Whole Foods have in common? They're leading the pack when it comes to hydrogen and fuel cells.

67

Investigation on Operating Characteristics of Individual Cell among Battery Pack.  

E-Print Network (OSTI)

??Due to the discrepancy among series-connected cells in a lead-acid battery pack, the restored capacities may not be the same during the charging/discharging processes. Through (more)

Chen, Wen-Chih

2006-01-01T23:59:59.000Z

68

A hybrid heuristic algorithm for the rectangular packing problem  

Science Conference Proceedings (OSTI)

A hybrid heuristic algorithm for the two-dimensional rectangular packing problem is presented. This algorithm is mainly based on divide-and-conquer and greedy strategies. The computational results on a class of benchmark problems have shown that the ...

Defu Zhang; Ansheng Deng; Yan Kang

2005-05-01T23:59:59.000Z

69

Lawrence Pack, train conductor, and Y-12s uranium  

NLE Websites -- All DOE Office Websites (Extended Search)

Lawrence Pack, train conductor, and Y-12's uranium? Trains were the primary means of long haul transportation in the 1940's. Many trains brought building materials to Y-12 and...

70

Arbitrary Convex and Concave Rectilinear Module Packing Using TCG  

Science Conference Proceedings (OSTI)

In this paper, we deal with arbitrary convex and concave rectilinearmodule packing using the Transitive Closure Graph (TCG) representation.The geometric meanings of modules are transparent to TCG and itsinduced operations, which makes TCG an ideal representation ...

J. Lin; H. Chen; Y. Chang

2002-03-01T23:59:59.000Z

71

Hazardous Waste: Resource Pack for Trainers and Communicators | Open Energy  

Open Energy Info (EERE)

Hazardous Waste: Resource Pack for Trainers and Communicators Hazardous Waste: Resource Pack for Trainers and Communicators Jump to: navigation, search Tool Summary Name: Hazardous Waste: Resource Pack for Trainers and Communicators Agency/Company /Organization: International Solid Waste Association (ISWA), United Nations Development Programme (UNDP), United Nations Industrial Development Organization (UNIDO) Sector: Energy, Land, Water Focus Area: Renewable Energy, - Waste to Energy Phase: Evaluate Options Topics: Adaptation, Implementation, Low emission development planning, -LEDS Resource Type: Guide/manual, Training materials Website: www.trp-training.info/ Cost: Paid Language: English References: Training Resource Pack[1] "The new TRP+ provides a structured package of notes, technical summaries, visual aids and other training material concerning the (hazardous) waste

72

Pseudo 3-D simulator optimizes gravel-packed completions  

SciTech Connect

This paper discusses a three-dimensional computer simulation which allows the consistent use of a gravel pack in oil and gas well completions. The primary thrust of the paper is dealing with horizontal oil and gas wells in unconsolidated reservoir rock. The model's objective is to provide an overall computer-aided design and evaluation tool for circulation and squeeze gravel packing. It is based on equations representing conservation of mass, momentum, and energy.

Ali, S.A.; Sanclemente, L.W. (Chevron USA Production Co., New Orleans, LA (United States)); Tupper, M.A. (Dowell, New Orleans, LA (United States))

1994-03-01T23:59:59.000Z

73

Instruction Packing for a 32-bit Stack-Based Processor  

E-Print Network (OSTI)

Abstract- This work proposed a design and development of a 32-bit stack-based processor for embedded systems. A reference processor has a 32-bit stack-based instruction set. This work proposed a technique of instruction packing which packs several instructions into one 32-bit instruction unit. Therefore, the instruction size is reduced. The result of the experiment shows that the proposed technique achieves around 30 % reduction in code size.

Witcharat Lertteerawattana; Tanes Jedsadawaranon; Prabhas Chongstitvatana

2007-01-01T23:59:59.000Z

74

Compilation of COG Packing Reports 2002-2003  

Science Conference Proceedings (OSTI)

Under a technical exchange agreement, EPRI has obtained several reports documenting research conducted by the Candu Owners Group (COG). This report presents a compilation of COG reports documenting research conducted in 20022003 to investigate the frictional performance characteristics of several valve packing materials that contain Teflon (PTFE). The testing conducted by the COG includes the effects of previous ionizing radiation exposure on the frictional performance of these packing materials

2006-05-02T23:59:59.000Z

75

Shock-Induced Flows through Packed Beds: Transient Regimes  

E-Print Network (OSTI)

The early stage of the transient regimes in the shock-induced flows within solid-packed beds are investigated in the linear longwave and high-frequency approximation. The transient resistance law is refined as the Duhameltime integral that follows from the general concept of dynamic tortuosity and compressibility of the packed beds. A closed-form solution is expected to describe accurately the early stage of the transient regime flow and is in qualitative agreement with available experimental data.

Yuri M. Shtemler; Isaac R. Shreiber; Alex Britan

2007-10-15T23:59:59.000Z

76

Modeling of an adiabatic packed bed brine-air contactor for use in a solar energy driven food processing system  

Science Conference Proceedings (OSTI)

A mathematical model was developed for a packed bed brine-air contacting system which has applications in a solar energy driven food processing system. The model considers mass transfer resistances of both phases, but neglects the heat transfer resistance of the liquid phase. It takes into account the large heat effects associated with water absorption into and desorption from the brine. A computational method was also developed to calculate the minimum air flow rate which would prevent a pinch. A packed bed brine-air contactor was built, and experiments were conducted for a range of brine and air conditions. Good agreement between the computed and experimental results warrants use of the model to design and optimize the packed bed water stripping process. A periodic-flow packed bed heat regenerator was built to recover heat from the exit air of the contactor so as to improve the energy efficiency of the system. It was possible to preheat the inlet air to a temperature close to that of the exit air. The inlet air, however, during its passage through the regenerator picked up the condensate deposited from the exit air. This led to a decrease in the driving potential to mass transfer in the contactor. Optimization studies show that using a combined solar driven boiler and air assisted packed bed water stripper would be more economical than using a solar driven boiler alone or using flat plate solar collectors to drive the water stripper.

Biswal, R.N.

1983-01-01T23:59:59.000Z

77

Down hole packing gland and method for long stroke pumper  

SciTech Connect

A packing gland is positioned down within an oil well hole and is held in place by elastomeric sealing and locking devices which are actuated from above the hole through a torque tube. Rotation of the torque tube in one direction lowers the tube axially relative to the elastomers and causes them to expand radially thus locking and sealing the stuffing gland assembly in the well head equipment at a depth of about 100 feet below the ground surface. Counter rotation of the torque tube allows the elastomers to retract radially thus releasing the stuffing gland assembly. Once the stuffing gland assembly is released, a union joint assembly is moved downward relative to the stuffing gland assembly and a unique spring ring slides over a cylindrical boss on the packing gland assembly to couple the union joint assembly with the packing gland assembly. The packing gland assembly then is raised above the ground surface simultaneously with lifting the polish rod from the hole. A drain port is provided between the elastomer locking and sealing devices to provide a flow passage back into the well when the packing gland is removed allowing the portion of the casing housing the wire rope to drain dry.

Hollenbeck, A.L.; De Tuerk, A.V.; Cooper, J.T.

1978-07-11T23:59:59.000Z

78

Fluid loss to formation stopped prior to gravel packing  

Science Conference Proceedings (OSTI)

Union Texas Petroleum has combined special techniques in offshore Louisiana gravel-packing operations to combat severe fluid loss that had jeopardized previous gravel-packed completions. By using an annulus pressure-controlled circulation valve and a crosslinked polymer gelled block, Union Texas was able to totally halt loss of fluid to a formation that had an 1,835-psi overbalanced (the hydrostatic pressure of well fluid in the treating string-to-casing annulus exceeded formation pressure by 1,835 psi). The pressure-controlled valve permitted process control without pipe movement, and the gelled block prevented fluid loss to the formation while the gravel pack was being installed. The well was perforated underbalanced, using tubing-conveyed guns, for perforation cleanup.

Quarnstrom, T.F. (Union Texas Petroleum, Houston, TX (US)); Cavender, T.W.; Shelton, G. (Vann Systems Houston, TX (US))

1989-09-25T23:59:59.000Z

79

Models for Metal Hydride Particle Shape, Packing, and Heat Transfer  

E-Print Network (OSTI)

A multiphysics modeling approach for heat conduction in metal hydride powders is presented, including particle shape distribution, size distribution, granular packing structure, and effective thermal conductivity. A statistical geometric model is presented that replicates features of particle size and shape distributions observed experimentally that result from cyclic hydride decreptitation. The quasi-static dense packing of a sample set of these particles is simulated via energy-based structural optimization methods. These particles jam (i.e., solidify) at a density (solid volume fraction) of 0.665+/-0.015 - higher than prior experimental estimates. Effective thermal conductivity of the jammed system is simulated and found to follow the behavior predicted by granular effective medium theory. Finally, a theory is presented that links the properties of bi-porous cohesive powders to the present systems based on recent experimental observations of jammed packings of fine powder. This theory produces quantitative experimental agreement with metal hydride powders of various compositions.

Kyle C. Smith; Timothy S. Fisher

2012-05-04T23:59:59.000Z

80

Hydrogen gettering packing material, and process for making same  

DOE Patents (OSTI)

A hydrogen gettering system for a sealed container is disclosed comprising packing material for use within the sealed container, and a coating film containing hydrogen gettering material on at least a portion of the surface of such packing material. The coating film containing the hydrogen gettering material comprises a mixture of one or more organic materials capable of reacting with hydrogen and one or more catalysts capable of catalyzing the reaction of hydrogen with such one or more organic materials. The mixture of one or more organic materials capable of reacting with hydrogen and the one or more catalysts is dispersed in a suitable carrier which preferably is a curable film-forming material. In a preferred embodiment, the packing material comprises a foam material which is compatible with the coating film containing hydrogen gettering material thereon.

LeMay, James D. (Castro Valley, CA); Thompson, Lisa M. (Knoxville, TN); Smith, Henry Michael (Overland Park, KS); Schicker, James R. (Lee' s Summit, MO)

2001-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "ah rated pack" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


81

Hydrogen gettering packing material and process for making same  

DOE Patents (OSTI)

A hydrogen gettering system for a sealed container is disclosed comprising packing material for use within the sealed container, and a coating film containing hydrogen gettering material on at least a portion of the surface of such packing material. The coating film containing the hydrogen gettering material comprises a mixture of one or more organic materials capable of reacting with hydrogen and one or more catalysts capable of catalyzing the reaction of hydrogen with such one or more organic materials. The mixture of one or more organic materials capable of reacting with hydrogen and the one or more catalysts is dispersed in a suitable carrier which preferably is a curable film-forming material. In a preferred embodiment, the packing material comprises a foam material which is compatible with the coating film containing hydrogen gettering material thereon.

LeMay, James D.; Thompson, Lisa M.; Smith, Henry Michael; Schicker, James R.

1999-09-09T23:59:59.000Z

82

Packing hyperspheres in high-dimensional Euclidean spaces  

E-Print Network (OSTI)

We present a study of disordered jammed hard-sphere packings in four-, five-, and six-dimensional Euclidean spaces. Using a collision-driven packing generation algorithm, we obtain the first estimates for the packing fractions of the maximally random jammed ?MRJ ? states for space dimensions d=4, 5, and 6 to be ? MRJ?0.46, 0.31, and 0.20, respectively. To a good approximation, the MRJ density obeys the scaling form ? MRJ=c 1/2 d +?c 2d?/2 d, where c 1=?2.72 and c 2=2.56, which appears to be consistent with the highdimensional asymptotic limit, albeit with different coefficients. Calculations of the pair correlation function g 2?r ? and structure factor S?k ? for these states show that short-range ordering appreciably decreases with increasing dimension, consistent with a recently proposed decorrelation principle, which, among other things, states that unconstrained correlations diminish as the dimension increases and vanish entirely in the limit d??. As in three dimensions ?where ? MRJ?0.64?, the packings show no signs of crystallization, are isostatic, and have a power-law divergence in g 2?r ? at contact with power-law exponent ?0.4. Across dimensions, the cumulative number of neighbors equals the kissing number of the conjectured densest packing close to where g 2?r ? has its first minimum. Additionally, we obtain estimates for the freezing and melting packing fractions for the equilibrium hard-sphere fluid-solid transition, ? F?0.32 and ? M ?0.39, respectively, for d=4, and ? F?0.20 and ? M ?0.25, respectively, for d=5. Although our results indicate the stable phase at high

Monica Skoge; Ar Donev; Frank H. Stillinger; Salvatore Torquato

2007-01-01T23:59:59.000Z

83

Experimental study of the heat and mass transfer in a packed bed liquid desiccant air dehumidifier  

Science Conference Proceedings (OSTI)

Desiccant cooling systems have the ability to provide efficient humidity and temperature control while reducing the electrical energy requirement for air conditioning as compared to a conventional system. Naturally, the desiccant air dehumidification process greatly influences the overall performance of the desiccant system. Therefore, the effects of variables such as air and desiccant flow rates, air temperature and humidity, desiccant temperature and concentration, and the area available for heat and mass transfer are of great interest. Due to the complexity of the dehumidification process, theoretical modeling relies heavily upon experimental studies. However, a limited number of experimental studies are reported in the literature. This paper presents results from a detailed experimental investigation of the heat and mass transfer between a liquid desiccant (triethylene glycol) and air in a packed bed absorption tower using high liquid flow rates. A high performance packing that combines good heat and mass transfer characteristics with low pressure drop is used. The rate of dehumidification, as well as the effectiveness of the dehumidification process are assessed based on the variables listed above. Good agreement is shown to exist between the experimental findings and predictions from finite difference modeling. In addition, a comparison between the findings in the present study and findings previously reported in the literature is made. The results obtained from this study make it possible to characterize the important variables which impact the system design.

Oeberg, V.; Goswami, D.Y. [Univ. of Florida, Gainesville, FL (United States)

1998-11-01T23:59:59.000Z

84

Inhibitory actions of Ah receptor agonists and indole-containing compounds in breast cancer cell lines and mouse models  

E-Print Network (OSTI)

The aryl hydrocarbon receptor (AhR) binds synthetic and chemoprotective phytochemicals, and research in this laboratory has developed selective AhR modulators (SAhRMs) for treatment of breast cancer. Activation of the AhR through agonists such as TCDD inhibits hormone activation of several E2-responsive genes in breast cancer cell lines. In this study, inhibition of E2-induced proliferation and gene expression by TCDD has been investigated in the uterus of wildtype, ERKO and AhRKO mice. Cyclin D1, DNA polymerase ?, and VEGF mRNA levels are induced by E2 through ER? in the uterus as determined by in situ hybridization studies. TCDD down-regulated E2-induced cyclin D1 and DNA polymerase ? expression, but not E2-induced VEGF expression, in wild-type mice, but not AhRKO mice, confirming the role of the AhR. Furthermore, protein synthesis was not necessary for induction of cyclin D1 or DNA polymerase ?gene expression by E2 or inhibition of these responses by TCDD. Therefore, AhR-ER? crosstalk directly regulates the expression of genes involved in cell proliferation in vivo. AhR agonists induce down-regulation of ErbB family receptors in multiple tissues/organs suggesting possible inhibitory interactions with chemotherapeutic potential. Recently, it has been reported that the SAhRM 1,1??,2,2??-tetramethyldiindolylmethane inhibited DMBA-induced mammary tumor growth in rats and also inhibited MAPK and PI3-K pathways in human breast cancer cells. BT-474 and MDA-MB-453 cell lines are ErbB2-overexpressing breast cancer cells that express functional AhR and exhibit constitutive activation of MAPK and PI3-K pathways. Therefore, 1,1??,2,2??-tetramethyldiindolylmethane-induced inhibition of ErbB2 signaling was investigated in these cells lines and in the MMTV-c-neu mouse mammary tumor model, which overexpresses ErbB2 in the mammary gland. The growth of ErbB2 overexpressing cell lines and mammary tumors was inhibited by 1,1??,2,2??-tetramethyldiindolylmethane; however, modulation of MAPK or PI3-K pathways and cell cycle proteins nor induction of apoptosis by 1,1',2,2'-tetramethyldiindolylmethane was observed in the ErbB2overexpressing cell lines. Current studies are investigating mitochondrial effects of 1,1??,2,2??-tetramethyldiindolylmethane in the ErbB2-overexpressing cell lines, as well as continuing studies on gene expression profiles in the mammary glands of MMTV-c-neu mice to better understand and identify critical genes that are responsible for ErbB2-mediated transformation and growth of cancer cells/tumors.

Walker, Kelcey Manae Becker

2002-05-01T23:59:59.000Z

85

DEFORMATION MODES OF PACKINGS OF FRICTIONLESS POLYDISPERSE SPHERES  

E-Print Network (OSTI)

1 DEFORMATION MODES OF PACKINGS OF FRICTIONLESS POLYDISPERSE SPHERES O. I. IMOLE, N. KUMAR, AND S as a function of volume fraction are reported for both uniaxial and deviatoric deformation modes. Our findings, and pressure (isotropic stress) are reported as function of volume fraction and isotropic strain, while

Luding, Stefan

86

Packed rod neutron shield for fast nuclear reactors  

DOE Patents (OSTI)

A fast neutron nuclear reactor including a core and a plurality of vertically oriented neutron shield assemblies surrounding the core. Each assembly includes closely packed cylindrical rods within a polygonal metallic duct. The shield assemblies are less susceptible to thermal stresses and are less massive than solid shield assemblies, and are cooled by liquid coolant flow through interstices among the rods and duct.

Eck, John E. (Hempfield Township, Westmoreland County, PA); Kasberg, Alvin H. (Murrysville, PA)

1978-01-01T23:59:59.000Z

87

Vibrations of Jammed Disk Packings with Hertzian Interactions  

E-Print Network (OSTI)

Contact breaking and Hertzian interactions between grains can both give rise to nonlinear vibrational response of static granular packings. We perform molecular dynamics simulations at constant energy in 2D of frictionless bidisperse disks that interact via Hertzian spring potentials as a function of energy and measure directly the vibrational response from the Fourier transform of the velocity autocorrelation function. We compare the measured vibrational response of static packings near jamming onset to that obtained from the eigenvalues of the dynamical matrix to determine the temperature above which the linear response breaks down. We compare packings that interact via single-sided (purely repulsive) and double-sided Hertzian spring interactions to disentangle the effects of the shape of the potential from contact breaking. Our studies show that while Hertzian interactions lead to weak nonlinearities in the vibrational behavior (e.g. the generation of harmonics of the eigenfrequencies of the dynamical matrix), the vibrational response of static packings with Hertzian contact interactions is dominated by contact breaking as found for systems with repulsive linear spring interactions.

Carl F. Schreck; Corey S. O'Hern; Mark D. Shattuck

2013-09-03T23:59:59.000Z

88

Energy Saving in Distillation Using Structured Packing and Vapor Recompression  

E-Print Network (OSTI)

"Distillation is a big consumer of energy in process plant operations. A first step to energy cost savings is the use of high efficiency structured packing in place of trays or dumped packings in conventionally operated distillation columns. Larger savings, as much as 80%, may be obtained by using a direct vapor recompression (VRC) heat pump instead of the conventional column operation with a steam heated reboiler. A main criterion of the suitability of a distillation for VRC is a low temperature difference across the column. VRC uses hot compressed overhead vapors, instead of steam, to heat the reboiler. Cost savings are highest when the pressure ratio for the compressor is low. The pressure ratio depends on the boiling point difference of top and bottom products, the reboiler-condenser driving force temperature and the column pressure drop. Structured packing has a low pressure drop; thus increasing the savings obtained with VRC - for retrofits or new columns - and increasing the range of applications where VRC is suitable for distillations. For low pressure distillation application, a column with a small pressure drop is especially important. An example of a vacuum distillation which is made suitable for VRC with use of structured packing is separation of styrene and ethyl benzene. "

Hill, J.H.

1987-09-01T23:59:59.000Z

89

Smart-Grid electricity allocation via strip packing with slicing  

Science Conference Proceedings (OSTI)

One advantage of smart grids is that they can reduce the peak load by distributing electricity-demands over multiple short intervals. Finding a schedule that minimizes the peak load corresponds to a variant of a strip packing problem. Normally, for strip ...

Soroush Alamdari, Therese Biedl, Timothy M. Chan, Elyot Grant, Krishnam Raju Jampani, Srinivasan Keshav, Anna Lubiw, Vinayak Pathak

2013-08-01T23:59:59.000Z

90

Experimental study of the performance of a laminar flow silica gel desiccant packing suitable for solar air conditioning application  

DOE Green Energy (OSTI)

An experimental study of the performance of a low pressure drop silica gel desiccant packing has been carried out. The packing is in the form of narrow passages lined with a single layer of small silica gel particles. A near optimum particle size of 0.25 mm, and a range of passage widths of 1.46 to 3.75 mm were chosen based on the predictions of a computer simulation model. A test chamber was constructed with sufficient thermal insulation to allow close to adiabatic conditions for the 12 cm x 12 cm cross section of packing. Step change adsorption and desorption tests were performed for various plate spacings, air flow rates, air inlet conditions, and gel initial water contents. Air outlet moisture content and temperature, as well as pressure drop were measured. The experimental results were compared with predictions of the computer simulation model: This model is based on gas side controlled heat and mass transfer, with the small solid side mass transfer resistance incorporated in a crude manner, and heat transfer into the packing handled as a lumped thermal capacitance. Reasonable agreement was obtained between theoretical prediction and experiment. The match was found to improve with increased passage width. The discrepancies are chiefly attributed to an excessive air bypass, and to inaccurate accounting for heat transfer from the sides of the unit. Use of the computer code for prototype scale design purposes is recommended.

Biswas, P.

1983-02-01T23:59:59.000Z

91

ANALYTICAL DATA SHEET ANALYTICAL DEPT. - HEALTH AhD SAFETY DlVlSlDN  

Office of Legacy Management (LM)

ANALYTICAL DEPT. - HEALTH AhD SAFETY DlVlSlDN I -. . Industrial Hygiene or Medical Dept. 1956 I. H.# 984 Sample Nos. l2 Date Collected- o/2g by&- Route to J" Location SSi4.X CUiTn! CXJitP. Type of Sample&-dust Analyzed for F Alpha x Remarks P~UXC~JGIi.' ON. 14lCI11~ U Beta - IIoll0Wi.n~ slucs - NO, Ra Oil PH Be Th Sample No. 7573p Hour Sample Description 1355 CZ Orxxator sets slul: into place, closes shield over machine S starts &ill. oil coolant flows through hollow drill ____ 3 is rebounded back through an openiq covers 1 cor.lp N9 8775 Analytical Chemistry Section: Date Received 7-2-66 by hb Date Reported 74X& bY IIR Method of Analysis Alpha sdntillation cam 2 % ' CJly Counting Data: BKGD .27 c/min GE0 4o% /min 1 I c- d/ill/M 3

92

HEALTH AhO SAFETY DIVISION Industrial Hygiene or Medical Dept.  

Office of Legacy Management (LM)

ALYTICAL DATA SHEET ALYTICAL DATA SHEET ANALYTICAL DEPT. - HEALTH AhO SAFETY DIVISION Industrial Hygiene or Medical Dept. m 1956 w I. H.# 7g2 Semplb Nos l2 Date Collected- 512 by RlX -----Route to EA LocetionKN(U[YTr-r-ETyp of Sample ~hd%---Analyzed for F Alphaxx Rema&mre t&n from the furnace and from U= Beta JOC slap ladles. No, Ro Oil PH Be Th Nc0 NO 8506 BcA-j &A- ii \JC cL"w-- Anolyticol Chemistry Secrion: Date Received--!b4-56 by Lab* Date Reported 6-X-66 bu I&b , Method of Analyair Vluarima4rFpt trio I APC&r BGM#2 . ~ Counting Date: BKGD GE0 G .H 1 K L M N slag from bottom of slag ladle Slag from bottom of slag ladle (Heat #8)) Refractory Wick from top ofc furnace I Slag from heat 1423 I Slag from heat #8 - top of slag ladle Slag lining from inside of arcfurnace (nprth fmce)

93

Effects of Sequence Partitioning on Compression Rate  

E-Print Network (OSTI)

In the paper, a theoretical work is done for investigating effects of splitting data sequence into packs of data set. We proved that a partitioning of data sequence is possible to find such that the entropy rate at each subsequence is lower than entropy rate of the source. Effects of sequence partitioning on overall compression rate are argued on the bases of partitioning statistics, and then, an optimization problem for an optimal partition is defined to improve overall compression rate of a sequence.

Alagoz, B Baykant

2010-01-01T23:59:59.000Z

94

Piston ring pack design effects on production spark ignition engine oil consumption : a simulation analysis  

E-Print Network (OSTI)

One of the most significant contributors to an engine's total oil consumption is the piston ring-pack. As a result, optimization of the ring pack is becoming more important for engine manufacturers and lubricant suppliers. ...

Senzer, Eric B

2007-01-01T23:59:59.000Z

95

The effect of surface finish on piston ring-pack performance in advanced reciprocating engine systems  

E-Print Network (OSTI)

Frictional losses in the piston ring-pack of an engine account for approximately 20% of the total frictional losses within an engine. Methods of surface texture optimization were investigated to reduce piston ring-pack ...

Jocsak, Jeffrey (Jeffrey Alan)

2005-01-01T23:59:59.000Z

96

Modeling the lubrication of the piston ring pack in internal combustion engines using the deterministic method  

E-Print Network (OSTI)

Piston ring packs are used in internal combustion engines to seal both the high pressure gas in the combustion chamber and the lubricant oil in the crank case. The interaction between the piston ring pack and the cylinder ...

Chen, Haijie

2011-01-01T23:59:59.000Z

97

Effects of lubricant viscosity and surface texturing on ring-pack performance in internal combustion engines  

E-Print Network (OSTI)

The piston ring-pack contributes approximately 25% of the mechanical losses in an internal combustion engine. Both lubricant viscosity and surface texturing were investigated in an effort to reduce this ring-pack friction ...

Takata, Rosalind (Rosalind Kazuko), 1978-

2006-01-01T23:59:59.000Z

98

Homochiral 3D Metal-Organic Frameworks from Chiral 1D Rods: 6 Way Helical Packing  

Science Conference Proceedings (OSTI)

The chiral 3D MOFs resulted from the packing of chiral 1D SBBs were studied. It was demonstrated that the final packing pattern is dependent on the dimension of SBB's. In addition, we were able to identify a new plywood-like network from ligand 2H2 exhibiting an unprecedented six-way chiral helical packing motif, which can be added on the list of invariant rod packings.

Shin, Sung M.; Moon, Dohyun; Jeong, Kyung S.; Kim, Jaheon; Thallapally, Praveen K.; Jeong, Nakcheol

2011-07-20T23:59:59.000Z

99

New packing in absorption systems for trapping benzene from coke-oven gas  

SciTech Connect

The efficiency of benzene removal from coke-oven gas in absorption units OAO Alchevskkoks with new packing is assessed.

V.V. Grabko; V.M. Li; T.A. Shevchenko; M.A. Solov'ev [Giprokoks, the State Institute for the Design of Coke-Industry Enterprises, Kharkov (Ukraine)

2009-07-15T23:59:59.000Z

100

Close-packed array of light emitting devices  

SciTech Connect

A close-packed array of light emitting diodes includes a nonconductive substrate having a plurality of elongate channels extending therethrough from a first side to a second side, where each of the elongate channels in at least a portion of the substrate includes a conductive rod therein. The conductive rods have a density over the substrate of at least about 1,000 rods per square centimeter and include first conductive rods and second conductive rods. The close-packed array further includes a plurality of light emitting diodes on the first side of the substrate, where each light emitting diode is in physical contact with at least one first conductive rod and in electrical contact with at least one second conductive rod.

Ivanov, Ilia N.; Simpson, John T.

2013-04-09T23:59:59.000Z

Note: This page contains sample records for the topic "ah rated pack" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


101

Internal states of model isotropic granular packings. III. Elastic properties  

E-Print Network (OSTI)

In this third and final paper of a series, elastic properties of numerically simulated isotropic packings of spherical beads assembled by different procedures and subjected to a varying confining pressure P are investigated. In addition P, which determines the stiffness of contacts by Hertz's law, elastic moduli are chiefly sensitive to the coordination number, the possible values of which are not necessarily correlated with the density. Comparisons of numerical and experimental results for glass beads in the 10kPa-10MPa range reveal similar differences between dry samples compacted by vibrations and lubricated packings. The greater stiffness of the latter, in spite of their lower density, can hence be attributed to a larger coordination number. Voigt and Reuss bounds bracket bulk modulus B accurately, but simple estimation schemes fail for shear modulus G, especially in poorly coordinated configurations under low P. Tenuous, fragile networks respond differently to changes in load direction, as compared to lo...

Agnolin, Ivana

2007-01-01T23:59:59.000Z

102

Biomass growth restriction in a packed bed reactor  

DOE Patents (OSTI)

When carrying out continuous biologically catalyzed reactions with anaerobic microorganisms attached to a support in an upflow packed bed column, growth of the microorganisms is restricted to prevent the microorganisms from plugging the column by limiting the availability of an essential nutrient and/or by the presence of predatory protozoa which consume the anaerobic microorganisms. A membrane disruptive detergent may be provided in the column to lyse dead microorganisms to make them available as nutrients for live microorganisms.

Griffith, William L. (Oak Ridge, TN); Compere, Alicia L. (Knoxville, TN)

1978-01-01T23:59:59.000Z

103

Numerical analysis of the heat transfer for packing design of cryogenic gate valve  

Science Conference Proceedings (OSTI)

The packing, among the components comprising the gate valve, is used to sustain the airtightness and the study on change of shape or pattern has been carried out to maximize the functions, but the study on changing the location or the size of the packing ... Keywords: cryogenic, heat transfer, liquefied natural gas, numerical analysis, packing

Si Pom Kim; Rock Won Jeon; Il Ju Hwang; Jae Hoon Lee; Won Heaop Shin

2012-04-01T23:59:59.000Z

104

Design of a Lithium-ion Battery Pack for PHEV Using a Hybrid Optimization Method  

E-Print Network (OSTI)

Design of a Lithium-ion Battery Pack for PHEV Using a Hybrid Optimization Method Nansi Xue1 Abstract This paper outlines a method for optimizing the design of a lithium-ion battery pack for hy- brid, volume or material cost. Keywords: Lithium-ion, Optimization, Hybrid vehicle, Battery pack design

Papalambros, Panos

105

High density packings of equal circles in rectangles with variable aspect ratio  

Science Conference Proceedings (OSTI)

Arranging a fixed number n of equal non-overlapping circles in a rectangle with variable aspect ratio is a non-standard packing problem. It arises if one has to decide how a certain number of circular items should be packed into a rectangular box when ... Keywords: Circle packing, Container design, Hexagonal grid, Rectangular container, Variable aspect ratio

E. Specht

2013-01-01T23:59:59.000Z

106

Biofiltration of isopentane in peat and compost packed beds  

Science Conference Proceedings (OSTI)

Commercially available biofiltration systems have used natural bioactive materials in packed beds due to low media cost and easy availability. Detailed understanding and modeling of biofiltration systems are lacking in existing literature. Experimental studies on the isopentane treatment in air using peat- and compost-packed beds were conducted with inlet isopentane concentrations of 360 to 960 ppmv, and empty-bed gas-phase residence times of 2 to 10 min. High removal efficiencies (>90%) were achieved at low contaminant concentrations (8 min). For both peat and compost biofilters, there was an optimal water content that gave the highest removal efficiency. For higher water content, mass transfer of isopentane through the liquid phase controlled the biofiltration removal efficiency. At low water content, irreversible changes in the bioactivity of peat and compost occurred, resulting in an irrecoverable loss of removal efficiency. Increases in biofilter bed temperature from 25 to 40 C improved the removal efficiency. A mathematical model incorporating the effect of water content and temperature was developed to describe the packed-bed biofilter performance. Model predictions agreed closely with experimental data.

Wang, Z.; Govind, R. [Univ. of Cincinnati, OH (United States). Dept. of Chemical Engineering

1997-05-01T23:59:59.000Z

107

Minimizing formation damage under adverse conditions during gravel pack operations  

Science Conference Proceedings (OSTI)

A method is described for minimizing formation damage caused by intrusive fluids prior to a gravel packing operation in loosely consolidated formations penetrated by at least one well comprising: (a) filling the casing of the well with an underbalanced completion fluid; (b) placing within the well a removable packer capable of isolating the space between the casing and the formation from the downhole well pressure; (c) setting through the packer a first tubing suitable for perforating and stabilizing the flow of fluids into the well; (d) perforating the casing; (e) introducing a blocking agent into the formation via the perforations which agent upon solidification is sufficient to minimize formation damage by avoiding the introduction of formation fluids where the agent is a gel; (f) causing the blocking agent to solidify while forming a solidified plug within the well and a solid mass within the adjacent washed out portion of the formation; (g) removing the first tubing from the well; (h) placing within the well a second tubing having a slotted portion therein sufficient to allow gravel packing of the well and the formation; (i) removing the solidified plug from the wellbore along with solidified gel from the washed-out portion of the formation; and (j) placing a gravel pack within the well and the washed-out portion of the formation via the second tubing which consolidates the formation.

Jennings, A.R. Jr.; Shu, P.

1989-03-14T23:59:59.000Z

108

Heat and mass transfer in packed bed liquid desiccant regenerators -- An experimental investigation  

Science Conference Proceedings (OSTI)

Liquid desiccant cooling can provide control of temperature and humidity, while at the same time lowering the electrical energy requirement for air conditioning. Since the largest energy requirement associated with desiccant cooling is low temperature heat for desiccant regeneration, the regeneration process greatly influences the overall system performance. Therefore, the effects of variables such as air and desiccant flow rates, air temperature and humidity, desiccant temperature and concentration, and the area available for heat and mass transfer on the regeneration process are of great interest. Due to the complexity of the regeneration process, which involves simultaneous heat and mass transfer, theoretical modeling must be verified by experimental studies. However, a limited number of experimental studies are reported in the literature. This paper presents results from a detailed experimental investigation of the heat and mass transfer between a liquid desiccant (triethylene glycol) and air in a packed bed regenerator using high liquid flow rates. To regenerate the desiccant, it is heated to temperatures readily obtainable from flat-plate solar collectors. A high performance packing that combines good heat and mass transfer characteristics with low pressure drop is used. The rate of water evaporation, as well as the effectiveness of the regeneration process is assessed based on the variables listed above. Good agreement is shown to exist between the experimental findings and predictions from finite difference modeling. In addition, the findings in the present study are compared to findings previously reported in the literature. Also, the results presented here characterize the important variables that impact the system design.

Martin, V.; Goswami, D.Y.

1999-08-01T23:59:59.000Z

109

Vehicle Details And Battery Specifications  

NLE Websites -- All DOE Office Websites (Extended Search)

Nominal Cell Voltage: 3.6 V Number of Electric Machines: 1 Nominal System Voltage: 144 V Motor: 17 kW (peak), Permanent Magnet, Liquid cooled Rated Pack Capacity: 4.7 Ah Maximum...

110

Free volume distribution of nearly jammed hard sphere packings  

E-Print Network (OSTI)

We calculate the free volume distributions of nearly jammed packings of monodisperse and bidisperse hard sphere configurations. These distributions differ qualitatively from those of the fluid, displaying a power law tail at large free volumes, which constitutes a distinct signature of nearly jammed configurations, persisting for moderate degrees of decompression. We reproduce and explain the observed distribution by considering the pair correlation function within the first coordination shell for jammed hard sphere configurations. We analyze features of the equation of state near jamming, and discuss the significance of observed asphericities of the free volumes to the equation of state.

Moumita Maiti; Srikanth Sastry

2013-09-26T23:59:59.000Z

111

The Effect of Load-Line Displacement Rate on the SCC Growth Rate of Nickel Alloys and Mechanistic Implications  

DOE Green Energy (OSTI)

A key set of SCC growth experiments was designed to test the hypothesis that deformation/creep is the rate controlling step in LPSCC. These tests were performed on Alloy X-750 AH compact tension specimens at a various constant displacement rates. The deformation/creep rate within the crack tip zone is proportional to the test displacement rate. If crack growth rates were observed to increase with the load-line displacement rate, then this would indicate that deformation/creep is a critical SCC mechanism process. However, results obtained from the load-line displacement tests did not find X-750 AH SCC growth rate to be dependent on the position rate and therefore do not support the assumption that deformation/creep is the rate controlling process in LPSCC. The similarities between the SCC response of X-750, Alloy 600 and EN82H suggests that it is likely that the same SCC process is occurring for all these alloys (i.e., the same rate controlling step) and that deformation based models are also inappropriate for Alloy 600 and EN82H. The strong temperature and coolant hydrogen dependencies exhibited by these alloys make it more likely that nickel alloy LPSCC is controlled by an environmental or corrosion driven process.

D Morton

2005-10-19T23:59:59.000Z

112

Dismantling (H)EV Battery Packs, an Integral Part of Umicore's ...  

Science Conference Proceedings (OSTI)

June 2012, a battery pack dismantling facility was opened in Maxton, NC based on ... Cost, Energy, Emissions, and Resource Assessment of the Production of...

113

Effects of residence time distribution and packing on methanol oxidation in biotrickling filter  

SciTech Connect

The effects of residence time distribution (RTD) on biotrickling filter systems and the comparison of the maximum elimination capacity (EC) and poisoning limits as functions of loadings of two packing media, Celite Biocatalyst Carrier R-635 and a subbituminous coal (Hat Creek coal from British Columbia), were studied. To alter the RTD patterns in the two reactor columns, two baffle designs were chosen. The RTD tests were done under dry conditions, over a range of airflow rates, with zero baffle, one baffle, and two baffles added into each column. Mixed culture from compost was used to acclimate the bed for the methanol removal efficiency study. No nutrients were added in the coal column. To study the poisoning limit, the inlet methanol concentration was randomly increased until a severe drop in removal efficiency occurred. From the RTD tests and the removal efficiency runs, which did not result in 100% conversion, number of tank-in-series (N) values, maximum EC values, and rate constants of each column with different baffle configurations could be obtained. Results from duplicate runs showed that addition of baffles decreased the N values of the columns and increased the back mixing in both systems. Maximum EC values, critical loadings, and poisoning limits also increased with increasing back mixing. Coal was superior to Celite Biocatalyst Carrier R-635 because it gave good conversions without additional nutrients. In all runs, the rate of methanol removal was controlled by a zero order process. 14 refs., 10 figs., 7 tabs.

Yuanita W. Hutomo; K.L. Pinder [University of British Columbia, Vancouver, BC (Canada). Chemical and Biological Engineering Department

2006-03-15T23:59:59.000Z

114

Potential use of battery packs from NCAP tested vehicles.  

Science Conference Proceedings (OSTI)

Several large electric vehicle batteries available to the National Highway Traffic Safety Administration are candidates for use in future safety testing programs. The batteries, from vehicles subjected to NCAP crashworthiness testing, are considered potentially damaged due to the nature of testing their associated vehicles have been subjected to. Criteria for safe shipping to Sandia is discussed, as well as condition the batteries must be in to perform testing work. Also discussed are potential tests that could be performed under a variety of conditions. The ultimate value of potential testing performed on these cells will rest on the level of access available to the battery pack, i.e. external access only, access to the on board monitoring system/CAN port or internal electrical access to the battery. Greater access to the battery than external visual and temperature monitoring would likely require input from the battery manufacturer.

Lamb, Joshua; Orendorff, Christopher J.

2013-10-01T23:59:59.000Z

115

Research Article Continuous Production of Lipase-Catalyzed Biodiesel in a Packed-Bed Reactor: Optimization and Enzyme Reuse Study  

E-Print Network (OSTI)

Copyright 2011 Hsiao-Ching Chen et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited. An optimal continuous production of biodiesel by methanolysis of soybean oil in a packed-bed reactor was developed using immobilized lipase (Novozym 435) as a catalyst in a tert-butanol solvent system. Response surface methodology (RSM) and Box-Behnken design were employed to evaluate the effects of reaction temperature, flow rate, and substrate molar ratio on the molar conversion of biodiesel. The results showed that flow rate and temperature have significant effects on the percentage of molar conversion. On the basis of ridge max analysis, the optimum conditions were as follows: flow rate 0.1 mL/min, temperature 52.1 ? C, and substrate molar ratio 1: 4. The predicted and experimental values of molar conversion were 83.31 2.07 % and 82.81 .98%, respectively. Furthermore, the continuous process over 30 days showed no appreciable decrease in the molar conversion. The paper demonstrates the applicability of using immobilized lipase and a packed-bed reactor for continuous biodiesel synthesis. 1.

Hsiao-ching Chen; Hen-yi Ju; Tsung-ta Wu; Yung-chuan Liu; Chih-chen Lee; Cheng Chang; Yi-lin Chung; Chwen-jen Shieh

2010-01-01T23:59:59.000Z

116

A new exact method for the two-dimensional bin-packing problem with fixed orientation  

Science Conference Proceedings (OSTI)

We propose a new exact method for the well-known two-dimensional bin-packing problem. It is based on an iterative decomposition of the set of items into two disjoint subsets. We tested the efficiency of our method against benchmarks of the literature. ... Keywords: Branch-and-bound, Cutting and packing, Dual-feasible functions, Lower bounds

FranOis Clautiaux; Jacques Carlier; Aziz Moukrim

2007-05-01T23:59:59.000Z

117

Designing nanostructured heterogeneous catalysts to exploit pulsing in gas-liquid packed bed reactors  

E-Print Network (OSTI)

41 Designing nanostructured heterogeneous catalysts to exploit pulsing in gas-liquid packed bed nanostructured catalysts for gas-liquid reactions, which have a system of macro pores designed to take advantage in volume of gas-liquid packed bed reactors (a.k.a. "trickle" beds) by an order of magnitude or more because

McCready, Mark J.

118

A hybrid genetic algorithm for a variant of two-dimensional packing problem  

Science Conference Proceedings (OSTI)

A variant of two-dimensional packing problem was given in the GECCO'2008 competition. This paper describes the genetic algorithm that produced the best result and thus won the No. 1 prize. As the problem is naturally represented by a two-dimensional ... Keywords: breadth-first search, geographic crossover, hybrid genetic algorithm, local search, packing, two-dimensional

Jin Kim; Byung-Ro Moon

2009-07-01T23:59:59.000Z

119

Molecular Packing Parameter in Bolaamphiphile Solutions: Adjustment of Aggregate Morphology by Modifying the Solution Conditions  

E-Print Network (OSTI)

Molecular Packing Parameter in Bolaamphiphile Solutions: Adjustment of Aggregate Morphology of Chemistry and Molecular Engineering, and College of Life Science, Peking UniVersity, Beijing, 100871, People of molecular packing parameters in a bolaamphiphile solution was tested with experimental results. By modifying

Huang, Jianbin

120

Research Article: Computational model for analyzing the evolutionary patterns of the neuraminidase gene of influenza A/H1N1  

Science Conference Proceedings (OSTI)

In this study, we performed computer simulations to evaluate the changes of selection potentials of codons in influenza A/H1N1 from 1999 to 2009. We artificially generated the sequences by using the transition matrices of positively selected codons over ... Keywords: Computer simulation, Evolution, H1N1 subtype, Influenza A virus, Neuraminidase

Insung Ahn; Hyeon Seok Son

2012-02-01T23:59:59.000Z

Note: This page contains sample records for the topic "ah rated pack" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


121

New indices of geomagnetic activity at test: Comparing the correlation of the analogue ak index with the digital Ah and IHV  

E-Print Network (OSTI)

New indices of geomagnetic activity at test: Comparing the correlation of the analogue ak index Abstract We test here two recently proposed indices of geomagnetic activity, the Ah index and the IHV index, which are based on digitally available hourly geomagnetic measurements. We study their correlation

Mursula, Kalevi

122

Stability of Satellites in Closely Packed Planetary Systems  

E-Print Network (OSTI)

We perform numerical integrations of four-body (star, planet, planet, satellite) systems to investigate the stability of satellites in planetary Systems with Tightly-packed Inner Planets (STIPs). We find that the majority of closely-spaced stable two-planet systems can stably support satellites across a range of parameter-space which is only slightly decreased compared to that seen for the single-planet case. In particular, circular prograde satellites remain stable out to $\\sim 0.4 R_H$ (where $R_H$ is the Hill Radius) as opposed to $\\sim 0.5 R_H$ in the single-planet case. A similarly small restriction in the stable parameter-space for retrograde satellites is observed, where planetary close approaches in the range 2.5 to 4.5 mutual Hill radii destabilize most satellites orbits only if $a\\sim 0.65 R_H$. In very close planetary pairs (e.g. the 12:11 resonance) the addition of a satellite frequently destabilizes the entire system, causing extreme close-approaches and the loss of satellites over a range of cir...

Payne, Matthew J; Holman, Matthew J; Perets, Hagai B

2013-01-01T23:59:59.000Z

123

PLANET-PLANET SCATTERING LEADS TO TIGHTLY PACKED PLANETARY SYSTEMS  

SciTech Connect

The known extrasolar multiple-planet systems share a surprising dynamical attribute: they cluster just beyond the Hill stability boundary. Here we show that the planet-planet scattering model, which naturally explains the observed exoplanet eccentricity distribution, can reproduce the observed distribution of dynamical configurations. We calculated how each of our scattered systems would appear over an appropriate range of viewing geometries; as Hill stability is weakly dependent on the masses, the mass-inclination degeneracy does not significantly affect our results. We consider a wide range of initial planetary mass distributions and find that some are poor fits to the observed systems. In fact, many of our scattering experiments overproduce systems very close to the stability boundary. The distribution of dynamical configurations of two-planet systems may provide better discrimination between scattering models than the distribution of eccentricity. Our results imply that, at least in their inner regions which are weakly affected by gas or planetesimal disks, planetary systems should be 'packed', with no large gaps between planets.

Raymond, Sean N. [Center for Astrophysics and Space Astronomy, 389 UCB, University of Colorado, Boulder, CO 80309 (United States); Barnes, Rory [Department of Astronomy, University of Washington, Seattle, WA 98195 (United States); Veras, Dimitri [Astronomy Department, University of Florida, Gainesville, FL 32111 (United States); Armitage, Philip J. [JILA, University of Colorado, Boulder, CO 80309 (United States); Gorelick, Noel [Google, Inc., 1600 Amphitheatre Parkway, Mountain View, CA 94043 (United States); Greenberg, Richard [Lunar and Planetary Laboratory, University of Arizona, Tucson, AZ (United States)], E-mail: sean.raymond@colorado.edu

2009-05-01T23:59:59.000Z

124

Rate Schedules  

Energy.gov (U.S. Department of Energy (DOE))

One of the major responsibilities of Southeastern is to design, formulate, and justify rate schedules. Repayment studies prepared by the agency determine revenue requirements and appropriate rate...

125

Breaker concentrations required to improve the permeability of proppant packs damaged by concentrated linear and borate-crosslinked fracturing fluids  

Science Conference Proceedings (OSTI)

This paper reports on the concentrations of an oxidative breaker required to reduce significantly the proppant-pack permeability damage caused by aqueous hydraulic fracturing fluids. Long-term, proppant-pack permeability testing was used to evaluate linear and borate-crosslinked gels. Results indicate that increasing the breaker concentration can reduce proppant-pack permeability damage very effectively.

Brannon, H. (BJ Services (United States)); Pulsinelli, R.J. (Dowell Schlumberger, Tulsa, OK (United States))

1992-11-01T23:59:59.000Z

126

Fast synchrotron X-ray tomography study of the rod packing structures  

SciTech Connect

We present a fast synchrotron X-ray tomography study of the packing structures of rods under tapping. Utilizing the high flux of the X-rays generated from the third-generation synchrotron source, we can complete a tomography scan within several seconds, after which the three-dimensional (3D) packing structure can be obtained for the subsequent structural analysis. Due to the high-energy nature of the X-ray beam, special image processing steps including image phase-retrieval has been implemented. Overall, this study suggests the possibility of acquiring statistically significant static packing structures within a reasonable time scale using high-intensity X-ray sources.

Zhang Xiaodan; Xia Chengjie; Sun Haohua; Wang Yujie [Department of Physics, Shanghai Jiao Tong University, 800 Dong Chuan Road, Shanghai 200240 (China)

2013-06-18T23:59:59.000Z

127

Dynamic performance of packed-bed dehumidifiers: experimental results from the SERI desiccant test loop  

DOE Green Energy (OSTI)

Discussed are the design and construction of a desiccant test loop and results of tests with a silica-gel-packed bed. The test loop consists of two centrifugal fans, two duct heaters, a steam humidifier, 24.4m (80 ft) of 30-cm (12-in.) circular duct, instrumentation, and a test section. The loop is capable of testing adsorption and desorption modes at flow rates up to 0.340 kg/s (600 scfm) and at regeneration temperatures up to 120/sup 0/C (248/sup 0/F). Tests of a 74-cm(29-in.)-diameter, 3.2-cm(1.25-in.)-thick silica gel bed indicated that mass transfer occurs more readily in the adsorption direction than in the desorption direction. Pressure drop data indicated that the resistance of each of the two screens that hold the silica gel in place was equivalent to 2.5-cm(1-in.) of silica gel due to plugging. Results of the tests were also used to validate a SERI desiccant computer model, DESSIM.

Kutscher, C F; Barlow, R S

1982-08-01T23:59:59.000Z

128

Rates - WAPA-137 Rate Order  

NLE Websites -- All DOE Office Websites (Extended Search)

WAPA-137 Rate Order WAPA-137 Rate Order 2009 CRSP Management Center Customer Rates Second Step Presentation from the June 25, 2009, Customer Meeting Handout Materials from the June 25, 2009, Customer Meeting Customer Comment Letters ATEA CREDA Farmington ITCA AMPUA Rate Adjustment Information The second step of WAPA-137 SLCA/IP Firm Power, CRSP Transmission and Ancillary Services rate adjustment. FERC Approval of Rate Order No. WAPA-137 Notice Of Filing for Rate Order No. WAPA-137 Published Final FRN for Rate Order No. WAPA-137 Letter to Customers regarding the published Notice of Extension of Public Process for Rate Order No. WAPA-137 Published Extension of Public Process for Rate Order No. WAPA-137 FRN Follow-up Public Information and Comment Forum Flier WAPA-137 Customer Meetings and Rate Adjustment Schedule

129

Facile synthesized nanorod structured vanadium pentoxide for high-rate lithium batteries  

Science Conference Proceedings (OSTI)

Nano-structured vanadium oxide (V2O5) is fabricated via facile thermal-decomposition of a vanadium precursor and vanadyl oxalate produced by reacting micro-sized V2O5 with oxalic acid. The V2O5 nanorods produced by this method exhibit much better electrochemical performance than commercial micro-sized V2O5. The optimized-nanorod electrodes with a high density of (001) planar defects give the best specific discharge capacities of 270 mAh g-1 at C/2 (147 mA g-1) coupled with good cycle stability with only 0.32% fading per cycle. Even at a high rate of 4C (1176 mA g-1), the nanorod electrode still delivers 198 mAh g-1. These results suggest that the nanostructured V2O5 is a good cathode for high-rate, lithium-ion battery applications.

Pan, Anqiang; Zhang, Jiguang; Nie, Zimin; Cao, Guozhong H.; Arey, Bruce W.; Li, Guosheng; Liang, Shu-quan; Liu, Jun

2010-04-23T23:59:59.000Z

130

Mesoscale Boundary Layer and Heat Flux Variations over Pack IceCovered Lake Erie  

Science Conference Proceedings (OSTI)

The development of extensive pack ice fields on the Great Lakes significantly influences lake-effect storms and local airmass modification, as well as the regional hydrologic cycle and lake water levels. The evolution of the ice fields and their ...

Mathieu R. Gerbush; David A. R. Kristovich; Neil F. Laird

2008-02-01T23:59:59.000Z

131

Designing Safe Lithium-Ion Battery Packs Using Thermal Abuse Models (Presentation)  

DOE Green Energy (OSTI)

NREL and NASA developed a thermal-electrical model that resolves PTC and cell behavior under external shorting, now being used to evaluate safety margins of battery packs for spacesuit applications.

Pesaran, A. A.; Kim, G. H.; Smith, K.; Darcy, E.

2008-12-01T23:59:59.000Z

132

Olive Oil: Chemistry and Technology, 2nd EditionChapter 11 Storage & Packing  

Science Conference Proceedings (OSTI)

Olive Oil: Chemistry and Technology, 2nd Edition Chapter 11 Storage & Packing Food Science Health Nutrition Biochemistry eChapters Food Science & Technology Health - Nutrition - Biochemistry Press Downloadable pdf...

133

Electrically recharged battery employing a packed/spouted bed metal particle electrode  

SciTech Connect

A secondary metal air cell, employing a spouted/packed metal particle bed and an air electrode. More specifically a zinc air cell well suited for use in electric vehicles which is capable of being either electrically or hydraulically recharged.

Siu, Stanley C. (Alameda, CA); Evans, James W. (Piedmont, CA); Salas-Morales, Juan (Berkeley, CA)

1995-01-01T23:59:59.000Z

134

Distillation: Energy Savings and Other Benefits From the Use of High Efficiency Packings  

E-Print Network (OSTI)

A great deal of attention has been focused lately on the use of high-efficiency packings for distillation applications. This paper discusses benefits that can be derived from the use of these devices. In particular, the reduction in energy requirements for a given separation is addressed for both new and retrofit applications. Pressure loss and product decomposition are also considered, and the basis for an alternative analysis is established. An example is shown in which an existing distillation tray column is retrofitted with a high-efficiency packing. The process advantages achieved, including energy savings, are discussed, as well as the factors governing the selection of the packing. The current limitations on design models for high-efficiency packings with respect to mass transfer efficiency, pressure drop, and capacity in distillation are mentioned briefly. Finally, the applications of these devices to alternative technologies such as liquid-liquid extraction are discussed.

Bravo, J. L.; Fair, J. R.; Humphrey, J. L.

1985-05-01T23:59:59.000Z

135

Energy Rating  

E-Print Network (OSTI)

Consistent, accurate, and uniform ratings based on a single statewide rating scale Reasonable estimates of potential utility bill savings and reliable recommendations on cost-effective measures to improve energy efficiency Training and certification procedures for home raters and quality assurance procedures to promote accurate ratings and to protect consumers Labeling procedures that will meet the needs of home buyers, homeowners, renters, the real estate industry, and mortgage lenders with an interest in home energy ratings

Cabec Conference; Rashid Mir P. E

2009-01-01T23:59:59.000Z

136

Insertion Rates  

Science Conference Proceedings (OSTI)

HOME > Insertion Rates. TECH HEADLINES. Research Explores a New Layer in Additive Manufacturin... Grand Opening Slated for Electron Microscopy Facility.

137

Technology Transfer Office University of Reading, Blandford Lodge, Whiteknights, Reading, RG6 6AH Tel: +44 (0)118 935 7100 Email: techtransfer@reading.ac.uk www.reading.ac.uk/working-with-business  

E-Print Network (OSTI)

Tel: +44 (0)118 935 7100 Email: techtransfer@reading.ac.uk www of Reading, Blandford Lodge, Whiteknights, Reading, RG6 6AH Tel: +44 (0)118 935 7100 Email: techtransfer

Reading, University of

138

Rate schedule  

NLE Websites -- All DOE Office Websites (Extended Search)

Firm Power Service Provided by Rate/Charges Firm Power Service Provided by Rate/Charges Rate/Charges Effective Through (or until superceded) Firm Sales (SLIP-F9) Composite Rate SLIP 29.62 mills/kWh 9/30/2015 Demand Charge SLIP $5.18/kW-month 9/30/2015 Energy Charge SLIP 12.19 mills/kWh 9/30/2015 Cost Recovery Charge (CRC) SLIP 0 mills/kWh 9/30/2015 Transmission Service Provided by Current Rates effective10/12 - 9/15 (or until superceded) Rate Schedule Effective Through Firm Point-to-Point Transmission (SP-PTP7) CRSP $1.14 per kW-month $13.69/kW-year $0.00156/kW-hour $0.04/kW-day $0.26/kW-week 10/1/2008-9/30/2015 Network Integration Transmission (SP-NW3) CRSP see rate schedule 10/1/2008-9/30/2015 Non-Firm Point-to-Point Transmission (SP-NFT6) CRSP see rate schedule 10/1/2008-9/30/2015 Ancillary Services Provided by Rate Rate Schedule

139

Foolproof completions for high rate production wells  

E-Print Network (OSTI)

Operators, especially those managing production from deepwater reservoirs, are striving to produce hydrocarbons at higher and higher rates without exposing the wells to completion failure risk. To avoid screen failures, recent studies have favored gravel pack (GP) and high rate water pack (HRWP) completions over high-permeability fracturing (HPF), known in the vernacular as a frac&pack (FP) for very high rate wells. While a properly designed GP completion may prevent sand production, it does not stop formation fines migration, and, over time, fines accumulation in the GP will lead to increasing completion skin. Although, and not always, the skin can be removed by acidizing, it is not practical to perform repeated acid treatments on deepwater wells, particularly those with subsea wellheads, and the alternative has been to subject the completion to increasingly high drawdown, accepting a high skin effect. A far better solution is to use a HPF completion. Of course the execution of a successful HPF is not a trivial exercise, and frequently, there is a steep learning curve for such a practice. This work explains the importance to HPF completions of the well trajectory through the interval to be hydraulically fractured, for production, not execution, reasons. A new model quantifies the effect of the well inclination on the connectivity between the fracture and the well via perforations. Guidelines based on the maximum target production rate, including forecasts of multiphase flow, are provided to size the HPF completion to avoid common completion failures that may result from high fluid rate and/or fines movement. Skin model will be developed for both vertical and deviated wells. Once the HPF is properly designed and executed, the operators should end up with a long term low skin good completion quality well. The well will be safely produced at the maximum flow rates, with no need for well surveillance and monitoring.

Tosic, Slavko

2007-12-01T23:59:59.000Z

140

PTF 10bzf (SN 2010ah): A BROAD-LINE Ic SUPERNOVA DISCOVERED BY THE PALOMAR TRANSIENT FACTORY  

Science Conference Proceedings (OSTI)

We present the discovery and follow-up observations of a broad-line Type Ic supernova (SN), PTF 10bzf (SN 2010ah), detected by the Palomar Transient Factory (PTF) on 2010 February 23. The SN distance is {approx_equal}218 Mpc, greater than GRB 980425/SN 1998bw and GRB 060218/SN 2006aj, but smaller than the other SNe firmly associated with gamma-ray bursts (GRBs). We conducted a multi-wavelength follow-up campaign with Palomar 48 inch, Palomar 60 inch, Gemini-N, Keck, Wise, Swift, the Allen Telescope Array, Combined Array for Research in Millimeter-wave Astronomy, Westerbork Synthesis Radio Telescope, and Expanded Very Large Array. Here we compare the properties of PTF 10bzf with those of SN 1998bw and other broad-line SNe. The optical luminosity and spectral properties of PTF 10bzf suggest that this SN is intermediate, in kinetic energy and amount of {sup 56}Ni, between non-GRB-associated SNe like 2002ap or 1997ef, and GRB-associated SNe like 1998bw. No X-ray or radio counterpart to PTF 10bzf was detected. X-ray upper limits allow us to exclude the presence of an underlying X-ray afterglow as luminous as that of other SN-associated GRBs such as GRB 030329 or GRB 031203. Early-time radio upper limits do not show evidence for mildly relativistic ejecta. Late-time radio upper limits rule out the presence of an underlying off-axis GRB, with energy and wind density similar to the SN-associated GRB 030329 and GRB 031203. Finally, by performing a search for a GRB in the time window and at the position of PTF 10bzf, we find that no GRB in the interplanetary network catalog could be associated with this SN.

Corsi, A. [LIGO Laboratory, California Institute of Technology, MS 100-36, Pasadena, CA 91125 (United States); Ofek, E. O.; Kulkarni, S. R.; Kasliwal, M. M. [Cahill Center for Astrophysics, California Institute of Technology, Pasadena, CA 91125 (United States); Frail, D. A. [National Radio Astronomy Observatory, P.O. Box 0, Socorro, NM 87801 (United States); Poznanski, D.; Nugent, P. [Computational Cosmology Center, Lawrence Berkeley National Laboratory, 1 Cyclotron Road, Berkeley, CA 94720 (United States); Arcavi, I.; Gal-Yam, A.; Green, Y.; Xu, D.; Ben-ami, S. [Department of Particle Physics and Astrophysics, The Weizmann Institute of Science, Rehovot 76100 (Israel); Hurley, K. [Space Sciences Laboratory, University of California Berkeley, 7 Gauss Way, Berkeley, CA 94720 (United States); Mazzali, P. A. [INAF-Osservatorio Astronomico, vicolo dell'Osservatorio 5, I-35122 Padova (Italy); Howell, D. A.; Murray, D. [Las Cumbres Observatory Global Telescope Network, Inc., Santa Barbara, CA 93117 (United States); Sullivan, M. [Department of Physics (Astrophysics), University of Oxford, DWB, Keble Road, Oxford OX1 3RH (United Kingdom); Bloom, J. S.; Cenko, S. B. [Department of Astronomy, 601 Campbell Hall, University of California, Berkeley, CA 94720-3411 (United States); Law, N. M., E-mail: corsi@caltech.edu [Dunlap Institute for Astronomy and Astrophysics, University of Toronto, 50 St. George Street, Toronto M5S 3H4, Ontario (Canada)

2011-11-10T23:59:59.000Z

Note: This page contains sample records for the topic "ah rated pack" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


141

Apparatus and method for determining solids circulation rate  

DOE Patents (OSTI)

The invention relates to a method of determining bed velocity and solids circulation rate in a standpipe experiencing a moving packed bed flow, such as the in the standpipe section of a circulating bed fluidized reactor The method utilizes in-situ measurement of differential pressure over known axial lengths of the standpipe in conjunction with in-situ gas velocity measurement for a novel application of Ergun equations allowing determination of standpipe void fraction and moving packed bed velocity. The method takes advantage of the moving packed bed property of constant void fraction in order to integrate measured parameters into simultaneous solution of Ergun-based equations and conservation of mass equations across multiple sections of the standpipe.

Ludlow, J. Christopher (Morgantown, WV); Spenik, James L. (Morgantown, WV)

2012-02-14T23:59:59.000Z

142

The Scaleup of Structured Packing from Distillation Pilot Plant Testing to Commercial Application  

E-Print Network (OSTI)

Structured packing is being utilized more and more in the process industry for increased efficiency, greater capacity, and energy savings in distillation columns. Pilot plant testing of the actual chemical system using commercially available structured packing is invaluable, but years of experience in pilot plant testing have shown that scaleup to successful commercial designs is a complicated process. In this paper an actual case history is cited as an example of the problems and benefits of conducting pilot plant tests which set the commercial design bases for a distillation train. The actual pilot plant testing involved a different structured packing type and blocked out operations to simulate a large number of theoretical stages. The pilot plant results verified the thermodynamic data to a high confidence level. As a result, the initial commercial installation of structured packing was started immediately. The actual installation and the startup are covered with a discussion of the energy savings and quality improvement which were obtained by replacing trays with the packing. Another case of retrofit testing in the new Koch Development Pilot Plant is discussed indicating other areas for attention to detail.

Berven, O. J.; Ulowetz, M. A.

1986-06-01T23:59:59.000Z

143

Design of a novel rotary compact power pack for the series hybrid electric vehicle. Design and simulation of a compact power pack consisting of a novel rotary engine and outer rotor induction machine for the series hybrid electric vehicle powertrain.  

E-Print Network (OSTI)

??Hybrid electric vehicles significantly reduce exhaust emissions and increase fuel economy. Power packs are the most fundamental components in a series powertrain configuration of a (more)

Amirian, Hossein

2010-01-01T23:59:59.000Z

144

Pull-Chain "Polymer" Solves Puzzle of Complex Molecular Packing |  

NLE Websites -- All DOE Office Websites (Extended Search)

Discovering New Talents for Diamond Discovering New Talents for Diamond Science Highlights Archives: 2013 | 2012 | 2011 | 2010 2009 | 2008 | 2007 | 2006 2005 | 2004 | 2003 | 2002 2001 | 2000 | 1998 | Subscribe to APS Science Highlights rss feed Pull-Chain "Polymer" Solves Puzzle of Complex Molecular Packing MARCH 4, 2010 Bookmark and Share Partial three-dimensional reconstruction, from x-ray tomographic data, of the packing of 2.1-mm ball chains, projected onto a plane. When tightly packed, the chains form nearly circular rigid loops, like the one in the lower right of the image. This behavior may form the basis of a model for better predictions of the rigidity of polymers. (Image courtesy of Ling-Nan Zou and Mark L. Rivers, The University of Chicago) Sometimes the simplest things hold the key to understanding complex

145

Adapting compilation techniques to enhance the packing of instructions into registers  

E-Print Network (OSTI)

The architectural design of embedded systems is becoming increasingly idiosyncratic to meet varying constraints regarding energy consumption, code size, and execution time. Traditional compiler optimizations are often tuned for improving general architectural constraints, yet these heuristics may not be as beneficial to less conventional designs. Instruction packing is a recently developed compiler/architectural approach for reducing energy consumption, code size, and execution time by placing the frequently occurring instructions into an Instruction Register File (IRF). Multiple IRF instructions are made accessible via special packed instruction formats. This paper presents the design and analysis of a compilation framework and its associated optimizations for improving the efficiency of instruction packing. We show that several new heuristics can be developed for IRF promotion, instruction selection, register re-assignment and instruction scheduling, leading to significant reductions in energy consumption, code size, and/or execution time when compared to results using a standard optimizing compiler targeting the IRF.

Stephen Hines; David Whalley; Gary Tyson

2006-01-01T23:59:59.000Z

146

Small scale ethanol production demonstration: comparison of packed versus plate rectifying column  

DOE Green Energy (OSTI)

The Johnson Environmental and Energy Center with assistance from the Madison County Farm Bureau Association received a grant in 1980 from the US Department of Energy to design, fabricate, and evaluate a small scale continuous ethanol plant. In 1981, the Center received a second DOE grant to compare the economics of replacing the plate rectifying column in the initial unit with a packed rectifying column. The results of the study indicate that the distillation unit with the packed rectifying column is capable of producing 14 gallons per hour of 170 proof ethanol. The energy ratio for distillation was a positive 2:1. Cost of the packed column was considerably less than the plate column. 1 reference, 19 figures, 9 tables.

Adcock, II, L E; Eley, M H; Schroer, B J

1982-07-01T23:59:59.000Z

147

Rates and Repayment Services  

NLE Websites -- All DOE Office Websites (Extended Search)

Tariff Rates FY 2014 Rates and Rate Schedules FY 2013 Rates and Rate Schedules FY 2012 Rates and Rate Schedules FY 2011 Rates and Rate Schedules FY 2010 Rates and Rate Schedules FY...

148

Modeling engine oil vaporization and transport of the oil vapor in the piston ring pack on internal combustion engines.  

E-Print Network (OSTI)

??A model was developed to study engine oil vaporization and oil vapor transport in the piston ring pack of internal combustion engines. With the assumption (more)

Cho, Yeunwoo, 1973-

2004-01-01T23:59:59.000Z

149

Adsorption and desorption of noble gases on activated charcoal: II. sup 222 Rn studies in a monolayer and packed bed  

SciTech Connect

The adsorptive and desorptive characteristics of canisters containing a petroleum-based charcoal were investigated under controlled conditions of temperature, relative humidity, and Rn concentration. Charcoals exposed in a monolayer and packed bed during exposure intervals of 1-7 d demonstrate that Rn adsorption and desorption are dependent on bed depth and the amount of water adsorbed. Changes in the adsorptive and desorptive properties of the charcoal occurred near the break-point where the pores became occluded by water vapor that condenses in the entrance capillaries. Radon-222 adsorption is decreased by an order of magnitude as the amount of adsorbed water exceeds the break-point of the charcoal. The reduction in pore surface due to adsorbed water results in a marked increase in the rate of Rn loss from exposed canisters, accounting for reduced adsorption. The apparent desorption time-constant for a 2-cm bed of loose Witco 6 x 10 mesh charcoal containing 0.220-0.365 kg H{sub 2}O kg-1 is typically between 2-8 h. The apparent desorption time-constant for an equivalent packed bed containing a water vapor content of 0.026-0.060 kg H{sub 2}O kg-1, which is below the break-point of the charcoal, is about 15-30 h. Conventional charcoal canisters, if exposed in the fully-opened configuration, can achieve the break-point in less than 4 d at 70% humidity. The use of a diffusion barrier would allow for longer exposure times until the break-point of the charcoal is achieved.

Scarpitta, S.C.; Harley, N.H. (Department of Energy, New York, NY (USA))

1990-10-01T23:59:59.000Z

150

Design and cost study of nickel--zinc batteries for electric vehicle. Final report. [24 kWh battery of 48 325-Ah cells, 35 Wh/lb  

DOE Green Energy (OSTI)

A battery module configuration consisting of four 325-Ah cells was selected. Twelve such modules would make up a 24-kWh battery. The key design parameter is operation current density. An energy density of 2.1 Wh/in./sup 3/ and 35 Wh/lb was obtained. A flow diagram was drawn for the manufacturing process. An eight-month period would be required to set up a pilot plant. The material requirements for 100,000 batteries per year would not have a significant impact on current U.S. consumption. 29 figures, 28 tables (RWR)

Klein, M; Dube, D

1976-10-01T23:59:59.000Z

151

Gas-Liquid Contact Area of Random and Structured Packing Ian David Wilson, B.S.  

E-Print Network (OSTI)

Gas-Liquid Contact Area of Random and Structured Packing By Ian David Wilson, B.S. Thesis Presented are preferred over spray and tray towers for gas/liquid contacting when minimizing pressure drop and maximizing the flue gas and the liquid solvent. The gas exits from the top with a low concentration of CO2 while

Rochelle, Gary T.

152

An observer looks at the cell temperature in automotive battery packs  

E-Print Network (OSTI)

An observer looks at the cell temperature in automotive battery packs Maxime Deberta , Guillaume.bloch@univ-lorraine.fr Abstract The internal temperature of Li-ion batteries for electric or hybrid vehicles is an important measurement and a model. This paper presents the simplified modelling of heat transfers in a battery module

Paris-Sud XI, Université de

153

Energy distributions and effective temperatures in the packing of elastic sheets  

E-Print Network (OSTI)

OFFPRINT Energy distributions and effective temperatures in the packing of elastic sheets S) 24002 www.epljournal.org doi: 10.1209/0295-5075/85/24002 Energy distributions and effective temperatures-section are broadly distributed. We find distributions of energy with exponential tails. This setup naturally divides

Boudaoud, Arezki

154

Energy distributions and effective temperatures in the packing of elastic sheets  

E-Print Network (OSTI)

Energy distributions and effective temperatures in the packing of elastic sheets S. Deboeuf, M of the branches forming the cross-section are broadly distributed. We find distributions of energy and within the bulk. While the geometrical properties of the sub-systems differ, their energy distributions

Paris-Sud XI, Université de

155

Electrically recharged battery employing a packed/spouted bed metal particle electrode  

DOE Patents (OSTI)

A secondary metal air cell, employing a spouted/packed metal particle bed and an air electrode, is described. More specifically a zinc air cell well suited for use in electric vehicles which is capable of being either electrically or hydraulically recharged. 5 figs.

Siu, S.C.; Evans, J.W.; Salas-Morales, J.

1995-08-15T23:59:59.000Z

156

A Genetic Algorithm with Exon Shuffling Crossover for Hard Bin Packing Problems  

E-Print Network (OSTI)

to fail. GAs Permission to make digital or hard copies of all or part of this work for personalA Genetic Algorithm with Exon Shuffling Crossover for Hard Bin Packing Problems Philipp Rohlfshagen segments from its parents. The algo- rithm is tested on a set of hard benchmark problems and the results

Heinke, Dietmar

157

Study of the collision of one rapid sphere on 3D packings: Experimental and numerical results  

Science Conference Proceedings (OSTI)

We report on experimental studies of the collision process between an incident bead and a three-dimensional packing of mono-size beads. The understanding of such a process and the resulting ejection of grains is, in particular, crucial to describe aeolian ... Keywords: DEM modelisation, Granular transport, Saltation

L. Oger; M. Ammi; A. Valance; D. Beladjine

2008-01-01T23:59:59.000Z

158

Questions & Answers Solicitation to Address High Purchase Costs and Disposal Impacts of PEV Battery Packs  

E-Print Network (OSTI)

Questions & Answers Solicitation to Address High Purchase Costs and Disposal Impacts of PEV Battery Packs PON12501 1. Relating to both Research Topic Areas, at what stage of the research does the Energ Commission envision a battery manufacturer needing to be involved? y The Energy

159

Silicon Atom Substitution Enhances Interchain Packing in a Thiophene-Based Polymer System  

SciTech Connect

A new silole-containing low bandgap polymer is synthesized by replacing the 5-position carbon of PCPDTBT with a silicon atom (PSBTBT). Through experiments and computational calculations, we show that the material properties, particular the packing of polymer chains, can be altered significantly. As a result, the polymer changes from amorphous to highly crystalline with the replacement of the silicon atom.

H Chen; J Hou; A Hayden; H Yang; K Houk; Y Yang

2011-12-31T23:59:59.000Z

160

Future perspectives of using hollow fibers as structured packings in light hydrocarbon distillation  

SciTech Connect

Olefin and paraffin are the largest chemical commodities. Furthermore, they are major building blocks for the petrochemical industry. Each year, petroleum refining, consumes 4,500 TBtu/yr in separation energy, making it one of the most energy-intensive industries in the United States). Just considering liquefied petroleum gas (ethane/propane/butane) and olefins (ethylene and propylene) alone, the distillation energy consumption is about 400 TBtu/yr in the US. Since petroleum distillation is a mature technology, incremental improvements in column/tray design will only provide a few percent improvements in the performance. However, each percent saving in net energy use amounts to savings of 10 TBtu/yr and reduces CO{sub 2} emissions by 0.2 MTon/yr. In practice, distillation columns require 100 to 200 trays to achieve the desired separation. The height of a transfer unit (HTU) of conventional packings is typical in the range of 36-60 inch. Since 2006, we had explored using several non-selective membranes as the structured packings to replace the conventional packing materials used in propane and propylene distillation. We obtained the lowest HTU of < 8 inch for the hollow fiber column, which was >5 times shorter than that of the conventional packing materials. In 2008, we also investigated this type of packing materials in iso-/n-butane distillation. Because of a slightly larger relative volatility of iso-/n-butane than that of propane/propylene, a wider and a more stable operational range was obtained for the iso-/n-butane pair. However, all of the experiments were conducted on a small scale with flowrate of < 25 gram/min. Recently, we demonstrated this technology on a larger scale (<250 gram/min). Within the loading range of F-factor < 2.2 Pa{sup 0.5}, a pressure drop on the vapor side is below 50 mbar/m, which suggests that the pressure drop of hollow fibers packings is not an engineering barrier for the applications in distillations. The thermal stability study suggests that polypropylene hollow fibers are stable after a long time exposure to C{sub 2} - C{sub 4} mixtures. The effects of packing density on the separation efficiency will be discussed.

Yang, Dali [Los Alamos National Laboratory; Orler, Bruce [Los Alamos National Laboratory; Tornga, Stephanie [Los Alamos National Laboratory; Welch, Cindy [Los Alamos National Laboratory

2011-01-26T23:59:59.000Z

Note: This page contains sample records for the topic "ah rated pack" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


161

Future perspectives of using hollow fibers as structured packings in light hydrocarbon distillation  

Science Conference Proceedings (OSTI)

Olefin and paraffin are the largest chemical commodities. Furthermore, they are major building blocks for the petrochemical industry. Each year, petroleum refining, consumes 4,500 TBtu/yr in separation energy, making it one of the most energy-intensive industries in the United States). Just considering liquefied petroleum gas (ethane/propane/butane) and olefins (ethylene and propylene) alone, the distillation energy consumption is about 400 TBtu/yr in the US. Since petroleum distillation is a mature technology, incremental improvements in column/tray design will only provide a few percent improvements in the performance. However, each percent saving in net energy use amounts to savings of 10 TBtu/yr and reduces CO{sub 2} emissions by 0.2 MTon/yr. In practice, distillation columns require 100 to 200 trays to achieve the desired separation. The height of a transfer unit (HTU) of conventional packings is typical in the range of 36-60 inch. Since 2006, we had explored using several non-selective membranes as the structured packings to replace the conventional packing materials used in propane and propylene distillation. We obtained the lowest HTU of 5 times shorter than that of the conventional packing materials. In 2008, we also investigated this type of packing materials in iso-/n-butane distillation. Because of a slightly larger relative volatility of iso-/n-butane than that of propane/propylene, a wider and a more stable operational range was obtained for the iso-/n-butane pair. However, all of the experiments were conducted on a small scale with flowrate of < 25 gram/min. Recently, we demonstrated this technology on a larger scale (<250 gram/min). Within the loading range of F-factor < 2.2 Pa{sup 0.5}, a pressure drop on the vapor side is below 50 mbar/m, which suggests that the pressure drop of hollow fibers packings is not an engineering barrier for the applications in distillations. The thermal stability study suggests that polypropylene hollow fibers are stable after a long time exposure to C{sub 2} - C{sub 4} mixtures. The effects of packing density on the separation efficiency will be discussed.

Yang, Dali [Los Alamos National Laboratory; Orler, Bruce [Los Alamos National Laboratory; Tornga, Stephanie [Los Alamos National Laboratory; Welch, Cindy [Los Alamos National Laboratory

2011-01-26T23:59:59.000Z

162

Measuring Frac-pack Conductivity at Reservoir Temperature and High Closure Stress  

E-Print Network (OSTI)

Ultra-deepwater reservoirs are important non-conventional reservoirs that hold the potential to produce billions of barrels of hydrocarbons but present major challenges. Hydraulic fracturing or frac-packing high permeability reservoirs is different from the conventional hydraulic fracturing technology used in low permeability formations. While the main purpose of the conventional technique is to create a long, highly conductive path, frac-packing on the other hand is used predominantly to get past near wellbore formation damage, control sand production and reduce near wellbore pressure drop. Ultra-deepwater reservoirs are usually high temperature and high pressure with high permeabilities. Frac-packing these types of wells requires short fractures packed with high proppant concentrations. Understanding the behavior of the fracture fluid and proppant is critical to pump such a job successfully and to ensure long term productivity from the fracture. A series of laboratory experiments have been conducted to research the different problems resulting from high temperature and pressure which negatively affect conductivity. Unlike conventional long-term conductivity measurements, we placed the proppant into the fracture and pumped fracture fluid through it and then measured conductivity by pumping oil to represent true reservoir conditions. Proppant performance and fracture fluids clean-up during production were examined. High strength proppant is ideal for deep fracture stimulations and in this study different proppant loadings at different stresses were tested to measure the impact of crushing and embedment on conductivity. The preliminary test results indicated that oil at reservoir conditions does improve clean-up of fracture fluid left back in the proppant pack. Increasing the proppant concentration in the fracture showed higher conductivity values even at high closure stress. The increase in effective closure stress with high temperature yielded significant loss in conductivity values as compared to those obtained from industry tests.

Fernandes, Preston X.

2009-08-01T23:59:59.000Z

163

Induction of 26S proteasome subunit PSMB5 by the bifunctional inducer 3-methylcholanthrene through the Nrf2-ARE, but not the AhR/Arnt-XRE, pathway  

Science Conference Proceedings (OSTI)

The 26S proteasome is responsible for degradation of abnormal intracellular proteins, including oxidatively damaged proteins and may play a role as a component of a cellular antioxidative system. However, little is known about regulation of proteasome expression. In the present study, regulation of proteasome expression by the bifunctional enzyme inducer and a specific signaling pathway for this regulation were investigated in murine neuroblastoma cells. Expression of catalytic core subunits including PSMB5 and peptidase activities of the proteasome were elevated following incubation with 3-methylcholanthrene (3-MC). Studies using reporter genes containing the murine Psmb5 promoter showed that transcriptional activity of this gene was enhanced by 3-MC. Overexpression of AhR/Arnt did not affect activation of the Pmsb5 promoter by 3-MC and deletion of the xenobiotic response elements (XREs) from this promoter exerted modest effects on inducibility in response to 3-MC. However, mutation of the proximal AREs of the Psmb5 promoter largely abrogated its inducibility by 3-MC. In addition, this promoter showed a blunted response toward 3-MC in the absence of nrf2; 3-MC incubation increased nuclear levels of Nrf2 only in wild-type cells. Collectively, these results indicate that expression of proteasome subunit PSMB5 is modulated by bifunctional enzyme inducers in a manner independent of the AhR/Arnt-XRE pathway but dependent upon the Nrf2-ARE pathway.

Kwak, Mi-Kyoung [College of Pharmacy, Yeungnam University, 214-1 Daedong, Gyeonsan-si, Gyeongsangbuk-do 712-749 (Korea, Republic of) and Department of Environmental Health Sciences, Johns Hopkins University Bloomberg School of Public Health, Baltimore, MD (United States)]. E-mail: mkwak@yumail.ac.kr; Kensler, Thomas W. [Department of Environmental Health Sciences, Johns Hopkins University Bloomberg School of Public Health, Baltimore, MD (United States)

2006-07-14T23:59:59.000Z

164

Rates and Repayment Services  

NLE Websites -- All DOE Office Websites (Extended Search)

Customer Letter - Preliminary Review of Drought Adder Component for 2011 Firm Power Rates 2010 Rates and Rate Schedule - Current * 2009 Rates and Rate Schedule 2008 Rates and...

165

Computation of Dancoff Factors for Fuel Elements Incorporating Randomly Packed TRISO Particles  

SciTech Connect

A new method for estimating the Dancoff factors in pebble beds has been developed and implemented within two computer codes. The first of these codes, INTRAPEB, is used to compute Dancoff factors for individual pebbles taking into account the random packing of TRISO particles within the fuel zone of the pebble and explicitly accounting for the finite geometry of the fuel kernels. The second code, PEBDAN, is used to compute the pebble-to-pebble contribution to the overall Dancoff factor. The latter code also accounts for the finite size of the reactor vessel and for the proximity of reflectors, as well as for fluctuations in the pebble packing density that naturally arises in pebble beds.

J. L. Kloosterman; Abderrafi M. Ougouag

2005-01-01T23:59:59.000Z

166

Removal of polychlorinated phenols in sequential anaerobic-aerobic biofilm reactors packed with tire chips  

Science Conference Proceedings (OSTI)

Scrap vehicle tire chips were used as packing material for sequential anaerobic-aerobic biofilm reactors to remove persistent chlorinated hydrocarbons. Adsorption capacity of scrap tires was greater under acidic conditions than under basic conditions. However, it was only approximately 0.04 to 0.3% of that of activated carbon. The amount of biomass that attached to the surface of scrap tires was 3.16 and 3.72 mg volatile suspended solids/cm{sup 2} after 14 and 37 days, respectively. Two laboratory-scale, down-flow anaerobic-aerobic biofilm reactors packed with tire chips were operated to remove 2,4-dichlorophenol (DCP) and 4-chlorophenol (CP). More than 98% of DCP was dehalogenated to CP in the anaerobic reactor, 70 to 98% of which was subsequently degraded in the aerobic reactor. Scrap tires did not cause any operational problems when used as biofilter media.

Shin, H.S.; Yoo, K.S.; Park, J.K.

1999-05-01T23:59:59.000Z

167

Valve Packing Performance Improvement: Sealing Technology and Plant Leakage Reduction Series  

Science Conference Proceedings (OSTI)

"Valve Packing Performance Improvement" is the seventh in a series of training modules addressing leakage at nuclear power plants. The first six modules in this series address: o Leakage management programs o Assembling bolted joints with spiral-wound gaskets o Preload requirements for bolted joints with spiral-wound gaskets o Lube oil system leakage mitigation o Leakage reduction from threaded joints o Leakage reduction from bolted joints with sheet gaskets

2002-03-28T23:59:59.000Z

168

Redesign of the SNS Modulator H-Bridge for Utilization of Press-Pack IGBTs  

SciTech Connect

The power conversion group at SLAC is currently redesigning the H-bridge switch plates of the High Voltage Converter Modulators at the Spallation Neutron Source. This integral part to the modulator operation has been indentified as a source of several modulator faults and potentially limits reliability with pulse width modulation operation. This paper is a presentation of the design and implementation of a redesigned switch plate based upon press-pack IGBTs.

Kemp, Mark A.; Burkhart, Craig; /SLAC; Anderson, David E.; /Oak Ridge

2008-09-25T23:59:59.000Z

169

Cavity method for force transmission in jammed disordered packings of hard particles  

E-Print Network (OSTI)

The force distribution of jammed disordered packings has always been considered a central object in the physics of granular materials. However, many of its features are poorly understood. In particular, analytic relations to other key macroscopic properties of jammed matter, such as the contact network and its coordination number, are still lacking. Here we develop a mean-field approach to this problem, based on the consideration of the contact network as a random graph where the force transmission becomes a constraint optimization problem. We can thus use the cavity method developed in the last decades within the statistical physics of spin glasses and hard computer science problems. This method allows us to compute the force distribution $\\text P(f)$ for random packings of hard particles of any shape, with or without friction. We find a new signature of jamming in the small force behavior $\\text P(f) \\sim f^{\\theta}$, whose exponent has attracted recent active interest. We find a finite value for $\\text P(f=0)$, along with $\\theta=0$ over an unprecedented six decades of force data, which agrees with experimental measurements on emulsion droplets. Furthermore, we relate the force distribution to a lower bound of the average coordination number ${\\bar z}_{\\rm c}^{\\rm min}(\\mu)$ of jammed packings of frictional spheres with coefficient $\\mu$. This bridges the gap between the two known isostatic limits ${\\bar z}_c(\\mu=0)=2D$ (in dimension $D$) and ${\\bar z}_c(\\mu \\to \\infty)=D+1$ by extending the naive Maxwell's counting argument to frictional spheres. The framework describes different types of systems, such as non-spherical objects and dimensions, providing a common mean-field scenario to investigate force transmission, contact networks and coordination numbers of jammed disordered packings.

Lin Bo; Romain Mari; Chaoming Song; Hernan A. Makse

2013-10-29T23:59:59.000Z

170

Recovery Act: Hydroelectric Facility Improvement Project - Replacement of Current Mechanical Seal System with Rope Packing System  

DOE Green Energy (OSTI)

Plans were immediately set in motion to begin the conversion from mechanical seals to a packing box at the facility. Contractors arrived on October 1st, 2012 and the project team began unwatering the unit for disassembly. The seal conversion was completed on February 29th, 2013 with start-up of the unit. Further testing and adjusting was done throughout the first two weeks of March.

Stephens, Jessica D.

2013-05-29T23:59:59.000Z

171

Distributed measurements of tracer response on packed bed flows using a fiberoptic probe array. Final report  

Science Conference Proceedings (OSTI)

Scale-up of packed bed processes, particularly those involving chromatographic separations, is made difficult by a seemingly inevitable increase in dispersion due to packing nonuniformity. To provide a suitable characterization, the authors measured the spatial distribution of dispersion and mixing in packed beds of uniform impervious spherical glass particles by a tracer impulse technique. The key feature in this work is the use of a fiberoptic array at the exit plane to obtain a time-resolved spatially distributed response. All experiments were in the creeping flow regime. The authors used a fluorescent dye with laser excitation through the fiber terminations in the bed. The fluoresced radiation was collected through the same fibers. They analyzed the data by the use of indices of the extent of micromixing based on Danckwerts`s original degree of segregation and an additional index of structural uniformity. The computations involve a moment analysis of the individual and average probe responses. A simple model gives expressions for the indices in terms of the Peclet number and is shown to provide a useful limiting case. The computed indices are also shown to be very sensitive to adsorption of dye on the surface of the glass. However, for some of the experiments with the largest spheres using Pyrex glass, the effects of adsorption are indiscernible. This technique successfully separates the contribution of micromixed fluid to overall bed dispersion from the contribution due to the transverse variation of the flow residence time.

Jones, M.C.; Nassimbene, R.; Wolfe, J. [National Inst. of Standards and Technology, Boulder, CO (United States). Chemical Science and Technology Lab.; Frederick, N. [Rocky Mountain Electron Video, Boulder, CO (United States)

1994-10-28T23:59:59.000Z

172

Rates and Repayment Services  

NLE Websites -- All DOE Office Websites (Extended Search)

Rates Loveland Area Project Firm Power Rates Transmission and Ancillary Services Rates 2012 Rate Adjustment-Transmission and Ancillary Services 2010 Rate Adjustment-Firm Power 2009...

173

Rates and Repayment Services  

NLE Websites -- All DOE Office Websites (Extended Search)

Rates and Repayment Services Consolidated Rate Schedules FY 2014 Rates BCP Annual Rate Process Central Arizona Project Transmission Rate Process DSW Multiple System Transmission...

174

Design and Study on the State of Charge Estimation for Lithium-ion Battery Pack in Electric Vehicle  

Science Conference Proceedings (OSTI)

State of charge (SOC) estimation is an increasingly important issue in battery management system (BMS) and has become a core factor to promote the development of electric vehicle (EV). In addition to offering the real time display of battery parameters ... Keywords: combination algorithm, state of charge (SOC), open circuit voltage (OCV), extended Kalman filtering (EKF), ampere hour (Ah), battery management system (BMS), electric vehicle (EV)

Jie Xu; Mingyu Gao; Zhiwei He; Jianbin Yao; Hongfeng Xu

2009-11-01T23:59:59.000Z

175

Phonon Dispersion and Elastic Moduli of Two-Dimensional Disordered Colloidal Packings of Soft-Particles with Frictional Interactions  

E-Print Network (OSTI)

Particle tracking and displacement covariance matrix techniques are employed to investigate the phonon dispersion relations of two-dimensional colloidal glasses composed of soft, thermoresponsive microgel particles whose temperature-sensitive size permits in situ variation of particle packing fraction. Bulk modulus, B, and shear modulus, G, of the colloidal glasses are extracted from the dispersion relations as a function of packing fraction. The ratio G/B is found to agree quantitatively with predictions for jammed packings of frictional soft particles with only one parameter required for the fit - the packing fraction for the onset of jamming in the limit of infinite friction. In addition, G and B individually agree with numerical predictions for frictional particles. This remarkable level of agreement enabled us to extract the inter-particle friction coefficient and an energy scale for the inter-particle interaction from the individual elastic constants.

Tim Still; Carl P. Goodrich; Ke Chen; Peter J. Yunker; Samuel Schoenholz; Andrea J. Liu; A. G. Yodh

2013-06-13T23:59:59.000Z

176

Modeling engine oil vaporization and transport of the oil vapor in the piston ring pack on internal combustion engines  

E-Print Network (OSTI)

A model was developed to study engine oil vaporization and oil vapor transport in the piston ring pack of internal combustion engines. With the assumption that the multi-grade oil can be modeled as a compound of several ...

Cho, Yeunwoo, 1973-

2004-01-01T23:59:59.000Z

177

Lipid Analysis and Lipidomics: New Techniques & ApplicationChapter 10 Lipid Separations Using Packed-Column Supercritical Fluid Chromatography  

Science Conference Proceedings (OSTI)

Lipid Analysis and Lipidomics: New Techniques & Application Chapter 10 Lipid Separations Using Packed-Column Supercritical Fluid Chromatography Methods and Analyses eChapters Methods - Analyses Books AOCS Press Downloadabl

178

Phonon Dispersion and Elastic Moduli of Two-Dimensional Disordered Colloidal Packings of Soft Particles with Frictional Interactions  

E-Print Network (OSTI)

Particle tracking and displacement covariance matrix techniques are employed to investigate the phonon dispersion relations of two-dimensional colloidal glasses composed of soft, thermoresponsive microgel particles whose temperature-sensitive size permits \\textit{in situ} variation of particle packing fraction. Bulk, $B$, and shear, $G$, moduli of the colloidal glasses are extracted from the dispersion relations as a function of packing fraction, and variation of the ratio $G/B$ with packing fraction is found to agree quantitatively with predictions for jammed packings of frictional soft particles. In addition, $G$ and $B$ individually agree with numerical predictions for frictional particles. This remarkable level of agreement enabled us to extract an energy scale for the inter-particle interaction from the individual elastic constants and to derive an approximate estimate for the inter-particle friction coefficient.

Tim Still; Carl P. Goodrich; Ke Chen; Peter J. Yunker; Samuel Schoenholz; Andrea J. Liu; A. G. Yodh

2013-06-13T23:59:59.000Z

179

Reduction of iron ore fines by coal fines in a packed bed and fluidized bed apparatus: A comparative study  

SciTech Connect

Reduction of iron ore fines by coal fines in packed and fluidized beds has been studied. The investigation includes study of the kinetic aspects of reduction, carbon and sulfur content of the direct reduced iron (DRI) produced, and metallography of the products. For both processes, the kinetic data fit the first-order reaction model. Reduction in a fluidized bed is much faster than in a packed bed system. In both cases, DRI contains a substantial amount of free carbon at the kinetic data fit the first-order reaction model. Reduction in a fluidized bed is much faster than in a packed bed system. In both cases, DRI contains a substantial amount of free carbon at the initial stages of reduction. At the later stages of reduction, the carbon present in the DRI is mainly in the combined state. For identical temperatures and particle sizes, reaction in fluidized bed is much faster compared to that in a packed bed. At any particular degree of reduction, sulfur content in DRI samples produced by fluidized bed reduction is always more than that of DRI samples produced by packed bed reduction. Scanning electron microscopy (SEM) micrographs reveal that metallic whiskers formed during reduction in packed beds only. These whiskers become more prominent at higher temperatures and longer times.

Haque, R. (Bangladesh Univ. of Engineering and Technology, Dhaka (Bangladesh). Metallurgical Engineering Department); Ray, H.S. (Regional Research Lab., Orissa (India)); Mukherjee, A. (Indian Inst. of Tech., (India).Metallurgical Engineering Department)

1993-06-01T23:59:59.000Z

180

Self-discharge rate of lithium thionyl-chloride cells  

DOE Green Energy (OSTI)

Our low-rate lithium/thionyl-chloride ``D`` cell is required to provide power continuously for up to 10 years. The cell was designed at Sandia National Laboratories and manufactured at Eagle-Picher Industries, Joplin, Missouri. We have conducted accelerated aging studies at elevated temperatures to predict long-term performance of cells fabricated in 1992. Cells using 1.0M LiAlCl{sub 4} electrolyte follow Arrhenius kinetics with an activation energy of 14.6 Kcal/mol. This results in an annual capacity loss to self-discharge of 0.13 Ah at 25 C. Cells using a 1.0M LiAlCl{sub 4}{sm_bullet}SO{sub 2} electrolyte do not follow Arrhenius behavior. The performance of aged cells from an earlier fabrication lot is variable.

Cieslak, W.R.

1993-12-31T23:59:59.000Z

Note: This page contains sample records for the topic "ah rated pack" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


181

Rates & Repayment  

NLE Websites -- All DOE Office Websites (Extended Search)

Environmental Review-NEPA Financial Data Operations Planning & Projects Power Marketing Rates Rate Adjustments Transmission Ancillary Services Rates WAPA-137 Rate Order Environmental Review-NEPA Financial Data Operations Planning & Projects Power Marketing Rates Rate Adjustments Transmission Ancillary Services Rates WAPA-137 Rate Order Rates and Repayment Services Rates Current and Historical Rate Information Collbran Power Rates CRSP Power Rates CRSP Transmission System Rates CRSP Management Center interest rates Falcon-Amistad Power Rates Provo River Power Rates Rio Grande Power Rates Seedskadee Power Rates SLCA/IP Power Rates Rate Schedules & Supplemental Rate Information Current Rates for Firm Power, Firm & Non-firm Transmission Service, & Ancillary Services Current Transmission & Ancillary Services Rates Tariffs Components of the SLCA/IP Existing Firm Power Rate Cost Recovery Charge (CRC) Page MOA Concerning the Upper Colorado River Basin

182

Report on Qiagen Columns with Precipitation versus Packed Bed Technology for Trace Amounts of DNA  

SciTech Connect

The assured limit of detection (LOD), where 100% of the PCR assays are successful, for the Qiagen spin column is dramatically improved when combined with an ethanol precipitation step of the eluted sample. A detailed SOP for the ethanol precipitation was delivered as a separate report. A key finding in the precipitation work was to incubate the ethanol precipitation at -20{sup o}C overnight when concentrating low copy number samples. Combining this modified ethanol precipitation with the Qiagen spin columns, the limit of assured detection was improved by 1-2 orders of magnitude, for the aliquot and assay variables used. The lower limit of detection (defined as when at least 1 assay of 1 aliquot was positive) was only improved by approximately 1 order of magnitude. The packed bed process has the potential of a 20-fold improvement in the limit of detection compared to Qiagen plus precipitation, based on a mass balance analysis for the entire DNA concentration and purification processes. Figure ES1 shows a mass balance for all the DNA processing steps. The packed bed process minimizes losses from elution, precipitation, and pipetting (aliquoting and transferring). Figure ES1 assumes that 100 copies of DNA serve as the input sample. Efficiencies for each step have been estimated based on our experiences or a worst case scenario (for example, a 50% loss was assumed for pipetting). Table ES1 summarizes the number of copies that are the input template for PCR assuming 100 copies of DNA are processed through the three options detailed in Figure ES1.Theoretically a 20-fold increase in the number of starting copies in the PCR reaction is gained when the DNA is concentrated, purified and then amplified directly on the surface of the beads in the packed bed.

Wheeler, E K; Erler, A M; Seiler, A

2008-02-05T23:59:59.000Z

183

The Brookhaven National Laboratory filter pack system for collection and determination of air pollutants  

Science Conference Proceedings (OSTI)

A filter pack system for sampling trace constituents in the atmosphere from aircraft and ground-based measurement platforms has been developed. The system simultaneously and quantitatively collects atmospheric aerosol, nitric acid, and sulfur dioxide using three sequential filter stages. The quartz aerosol filter is routinely analyzed for sulfate, nitrate, ammonium, and hydrogen ions, and specifically for sulfuric acid. The sodium chloride filter is analyzed for nitrate ion (from collected nitric acid), and the carbonate-glycerine filter for sulfate ion (from collected sulfur dioxide). Details of the procedures used for filter preparation, sampling, extraction and analysis are given.

Leahy, D.F.; Klotz, P.J.; Springston, S.R.; Daum, P.H.

1995-04-01T23:59:59.000Z

184

High-Rate Cathodes Based on Li3V2(PO4)3 Nanobelts Prepared via Surfactant-Assisted Fabrication  

DOE Green Energy (OSTI)

In this work, we synthesized monoclinic Li3V2(PO4)3 nanobelts via a single-step, solid-state reaction process in a molten hydrocarbon. The as-prepared Li3V2(PO4)3 nanoparticles have a unique nanobelt shape and are ~50-nm thick. When cycled in a voltage range between 3.0 V and 4.3V at a 1C rate, these unique Li3V2(PO4)3 nanobelts demonstrated a specific discharge capacity of 131 mAh g-1 (which is close to the theoretical capacity of 132 mAh g-1) and stable cycling characteristics.

Pan, Anqiang; Choi, Daiwon; Zhang, Jiguang; Liang, Shu-quan; Cao, Guozhong; Nie, Zimin; Arey, Bruce W.; Liu, Jun

2011-04-01T23:59:59.000Z

185

The Formation of Systems with Tightly-packed Inner Planets (STIPs) via Aerodynamic Drift  

E-Print Network (OSTI)

The NASA Kepler mission has revealed an abundant class of Systems with Tightly-packed Inner Planets (STIPs). The current paradigm for planet formation suggests that small planetesimals will quickly spiral into the host star due to aerodynamic drag, preventing rocky planet formation. In contrast, we find that aerodynamic drift, when acting on an ensemble of solids, can concentrate mass at short orbital periods in gaseous disks. Sublimation fronts may further aid this process. Kepler data suggest that the innermost known planets are found near the silicate sublimation zone. STIP planets should have a wide range of volatile fractions due to aerodynamic drift and H2 dissociation-driven gas accretion. We further propose that the low mass of Mars is evidence that the Solar System was once a proto-STIP.

Boley, Aaron C

2013-01-01T23:59:59.000Z

186

Integration Issues of Cells into Battery Packs for Plug-in and Hybrid Electric Vehicles: Preprint  

DOE Green Energy (OSTI)

The main barriers to increased market share of hybrid electric vehicles (HEVs) and commercialization of plug-in HEVs are the cost, safety, and life of lithium ion batteries. Significant effort is being directed to address these issues for lithium ion cells. However, even the best cells may not perform as well when integrated into packs for vehicles because of the environment in which vehicles operate. This paper discusses mechanical, electrical, and thermal integration issues and vehicle interface issues that could impact the cost, life, and safety of the system. It also compares the advantages and disadvantages of using many small cells versus a few large cells and using prismatic cells versus cylindrical cells.

Pesaran, A. A.; Kim, G. H.; Keyser, M.

2009-05-01T23:59:59.000Z

187

Dislocation Dynamics Simulations of Junctions in Hexagonal Close-Packed Crystals  

SciTech Connect

The formation and strength of dislocations in the hexagonal closed packed material beryllium are studied through dislocation junctions and the critical stress required to break them. Dislocation dynamics calculations (using the code ParaDiS) of junction maps are compared to an analytical line tension approximation in order to validate our model. Results show that the two models agree very well. Also the critical shear stress necessary to break 30{sup o} - 30{sup o} and 30{sup o} - 90{sup o} dislocation junctions is computed numerically. Yield surfaces are mapped out for these junctions to describe their stability regions as function of resolved shear stresses on the glide planes. The example of two non-coplanar binary dislocation junctions with slip planes [2-1-10] (01-10) and [-12-10] (0001) corresponding to a prismatic and basal slip respectively is chosen to verify and validate our implementation.

Wu, C; Aubry, S; Chung, P; Arsenlis, A

2011-12-05T23:59:59.000Z

188

Scaling relation for the bond length, mass density, and packing order of water ice  

E-Print Network (OSTI)

The packing order of molecules and the distance between adjacent oxygen atoms (dOO) in water and ice are most basic yet puzzling. Here we present a scaling solution for this purpose based only on the mass density (gcm-3), (Equation) where dL is the length ({\\AA}) of the O:H van der Waals bond and dH the H-O polar-covalent bond projecting on the O---O line. Validated by the measured proton symmetrization of compressed ice, dOO of water and ice, and dOO expansion at water surface, this solution confirms that the fluctuated, tetrahedrally-coordinated structure is unique for water ice.

Chang Q Sun

2013-05-18T23:59:59.000Z

189

Ready to implement CIM Monolith Technology Order our CIM Disk Virus Purification Pack and identify the optimal chemistry  

E-Print Network (OSTI)

Ready to implement CIM® Monolith Technology Order our CIM® Disk Virus Purification Pack. Request a CIM® Technology Seminar? To educate your entire organization about CIM® Technology and its- on with the performance or use of CIM®. For more information on our products, visit our home page at: http

Lebendiker, Mario

190

A Preliminary Study of the Effect of Shifts in Packing Fraction on k-effective in Pebble-Bed Reactors  

Science Conference Proceedings (OSTI)

A preliminary examination of the effect of pebble packing changes on the reactivity of a pebble-bed reactor (PBR) is performed. As a first step, using the MCNP code, the modeling of a PBR core as a continuous and homogenous region is compared to the modeling as a collection of discrete pebbles of equal average fuel density. It is shown that the two modeling approaches give the same trends inasmuch as changes in keff are concerned. It is thus shown that for the purpose of identifying trends in keff changes, the use of a homogeneous model is sufficient. A homogenous model is then used to assess the effect of pebble packing arrangement changes on the reactivity of a PBR core. It is shown that the changes can be large enough to result in prompt criticality. It is shown that for uranium fueled PBRs, thermal feedback could have the potential to offset the increase in activity, whereas for plutonium fueled systems, thermal feedback may not be sufficient for totally offsetting the packing-increase reactivity insertion and could even exacerbate the initial response. It is thus shown that a full study, including reactor kinetics, thermal feedback, and the dynamics of energy deposition and removal is warranted to fully characterize the potential consequences of packing shifts.

Ougouag, Abderrafi Mohammed-El-Ami; Terry, William Knox

2001-09-01T23:59:59.000Z

191

Accelerating Palladium-Catalyzed C-F Bond Formation: Use of a Microflow Packed-Bed Reactor  

E-Print Network (OSTI)

A flow process for Pd-catalyzed C-F bond formation is described. A microreactor with a packed-bed design allows for easy handling of large quantities of insoluble CsF with precise control over reaction times, efficient ...

Maimone, Thomas J.

192

FREE Name Tags for 1st year Students FREE Selected Course Packs for 2nd year Students  

E-Print Network (OSTI)

· FREE Name Tags for 1st year Students · FREE Selected Course Packs for 2nd year Students Process · Discounts & Free Registration to Events · Financial Support for Student Projects & Groups (up to $11,000 each year!) · Discounts on Insurance, Rental Cars, and more! · FREE Legal Advice · Expanded

Liu, Taosheng

193

Design Of A Hybrid Jet Impingement / Microchannel Cooling Device For Densely Packed PV Cells Under High Concentration  

Science Conference Proceedings (OSTI)

A hybrid jet impingement / microchannel cooling scheme was designed and applied to densely packed PV cells under high concentration. An experimental study allows validating the principles of the design and confirming its applicability to the cited system. In order to study the characteristics of the device in a wide range of conditions

Jrme Barrau; Joan Rosell; Manel Ibaez

2010-01-01T23:59:59.000Z

194

An Integrated Power Pack of Dye-Sensitized Solar Cell and Li Battery Based on Double-Sided TiO2 Nanotube Arrays  

E-Print Network (OSTI)

An Integrated Power Pack of Dye-Sensitized Solar Cell and Li Battery Based on Double-Sided TiO2 harvest and storage processes. This power pack incorporates a series-wound dye- sensitized solar cell material.11,15 Compared with other integrated solar power supplies,16,17 double-sided TiO2 NTs with large

Wang, Zhong L.

195

Improved Battery Pack Thermal Management to Reduce Cost and Increase Energy Density: Cooperative Research and Development Final Report, CRADA Number CRD-12-499  

SciTech Connect

Under this CRADA NREL will support Creare's project for the Department of Energy entitled 'Improved Battery Pack Thermal Management to Reduce Cost and Increase Energy Density' which involves the development of an air-flow based cooling product that increases energy density, safety, and reliability of hybrid electric vehicle battery packs.

Smith, K.

2013-10-01T23:59:59.000Z

196

Recovery Act: Hydroelectric Facility Improvement Project - Replacement of Current Mechanical Seal System with Rope Packing System  

SciTech Connect

On January 27, 2010 the City of North Little Rock, Arkansas received notification of the awarding of a Department of Energy (DOE) grant totaling $450,000 in funding from the American Recovery and Reinvestment Act (ARRA) under the Project Title: Recovery Act: Hydroelectric Facility Improvement Project Automated Intake Clearing Equipment and Materials Management. The purpose of the grant was for improvements to be made at the Citys hydroelectric generating facility located on the Arkansas River. Improvements were to be made through the installation of an intake maintenance device (IMD) and the purchase of a large capacity wood grinder. The wood grinder was purchased in order to receive the tree limbs, tree trunks, and other organic debris that collects at the intake of the plant during high flow. The wood grinder eliminates the periodic burning of the waste material that is cleared from the intake and reduces any additional air pollution to the area. The resulting organic mulch has been made available to the public at no charge. Design discussion and planning began immediately and the wood grinder was purchased in July of 2010 and immediately put to work mulching debris that was gathered regularly from the intake of the facility. The mulch is currently available to the public for free. A large majority of the design process was spent in discussion with the Corps of Engineers to obtain approval for drawings, documents, and permits that were required in order to make changes to the structure of the powerhouse. In April of 2011, the Citys Project Engineer, who had overseen the application, resigned and left the Citys employ. A new Systems Mechanical Engineer was hired and tasked with overseeing the project. The transfer of responsibility led to a re-examination of the original assumptions and research upon which the grant proposal was based. At that point, the project went under review and a trip was booked for July 2011 to visit facilities that currently had an IMD installed. This further study of facilities revealed that the implementation of the project as originally described, while proving the benefits described in the original grant application, would likely intensify sand intake. Increased sand intake would lead to an increase in required shutdowns for maintenance and more rapid depreciation of key equipment which would result in a loss of generation capacity. A better solution to the problem, one that continued to meet the criteria for the original grant and ARRA standards, was developed. A supporting day trip was planned to visit other facilities located on the Arkansas River to determine how they were coping with the same strong amounts of sand, silt, and debris. Upon returning from the trip to other Arkansas River facilities it was extremely clear what direction to go in order to most efficiently address the issue of generator capacity and efficiency. Of the plants visited on the Arkansas River, every one of them was running what is called a rope packing shaft sealing system as opposed to mechanical shaft seals, which the facility was running. Rope packing is a time proven sealing method that has been around for centuries. It has proved to perform very well in dirty water situations just like that of the Arkansas River. In April of 2012 a scope change proposal was submitted to the DOE for approval. In August of 2012 the City received word that the change of scope had been approved. Plans were immediately set in motion to begin the conversion from mechanical seals to a packing box at the facility. Contractors arrived on October 1st, 2012 and the project team began unwatering the unit for disassembly. The seal conversion was completed on February 29th, 2013 with start-up of the unit. Further testing and adjusting was done throughout the first two weeks of March.

Stephens, Jessica D.

2013-05-29T23:59:59.000Z

197

Data Center Rating Infrastructure Rating Development  

NLE Websites -- All DOE Office Websites (Extended Search)

in Portfolio Manager on June 7, 2010. The questions below are designed to help data center owners and operators better understand the rating and benchmark their buildings in...

198

Tracking the Libor Rate  

E-Print Network (OSTI)

Investigating the Libor Rate, mimeo. Abrantes-Metz, R. ,Libor data: Historial 1 month Libor rates, British Bankers1108R) Tracking the Libor Rate Rosa M. Abrantes-Metz , Sofia

Abrantes-Metz, Rosa; Villas-Boas, Sofia B.; Judge, George G.

2013-01-01T23:59:59.000Z

199

Performance characteristics and modeling of carbon dioxide absorption by amines in a packed column  

Science Conference Proceedings (OSTI)

Carbon dioxide (CO[sub 2]) is widely recognized as a major greenhouse gas contributing to global warming. To mitigate the global warming problem, removal of CO[sub 2] from the industrial flue gases is necessary. Absorption of carbon dioxide by amines in a packed column was experimentally investigated. The amines employed in the present study were the primary mono-ethanolamine (MEA) and tertiary N-methyldiethanolamine (MDEA), two very popular amines widely used in the industries for gas purification. The CO[sub 2] absorption characteristics by these two amines were experimentally examined under various operating conditions. A theoretical model was developed for describing the CO[sub 2] absorption behavior. Test data have revealed that the model predictions and the observed CO[sub 2] absorption breakthrough curves agree very well, validating the proposed model. Preliminary regeneration tests of exhausted amine solution were also conducted. The results indicated that the tertiary amine is easier to regenerate with less loss of absorption capacity than the primary one.

Lin, S.H.; Shyu, C.T. (Yuan Ze Univ., Taoyuan (Taiwan, Province of China). Dept. of Chemical Engineering)

1999-01-01T23:59:59.000Z

200

Selenite Reduction by a Denitrifying Culture: Batch- and Packed-Bed- Reactor Studies  

SciTech Connect

Selenite reduction by a bacterial consortium enriched from an oil refinery waste sludge was studied under denitrifying conditions using acetate as the electron donor. Fed-batch studies with nitrate as the primary electron acceptor showed that accumulation of nitrite led to a decrease in the extent of selenite reduction. Also, when nitrite was added as the primary electron acceptor, rapid selenite reduction was observed only after nitrite was significantly depleted from the medium. These results indicate that selenite reduction was inhibited at high nitrite concentrations. In addition to batch experiments, continuous flow selenite reduction experiments were performed in packed-bed columns using immobilized enrichment cultures. These experiments were carried out in three phases: In phase-I, a continuous nitrate feed with different inlet selenite concentration was applied; in phase-II, nitrate was fed in a pulsed fashion; and in phase-III, nitrate was fed in a continuous mode but at much lower concentrations than the other two phases. During the phase-I experiments, little selenite was removed from the influent. However, when the column was operated in the pulse feed strategy (phase II), or in the continuous mode with low nitrate levels (phase-III), significant quantities of selenium was removed from solution and retained in the immobilization matrix in the column. Thus, immobilized denitrifying cultures can be effective in removing selenium from waste streams, but nitrate-limited operating conditions might be required.

William A. Apel; Sridhar Viamajala; Yared Bereded-Samuel; James N. Petersen

2006-08-01T23:59:59.000Z

Note: This page contains sample records for the topic "ah rated pack" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


201

Resin Liner Recovery and Over-Packing at Ontario Power Generation's Western Waste Management Facility  

SciTech Connect

Spent resins generated from Ontario Power Generation (OPG)'s and Bruce Power's Candu reactor operations are stored at OPG's Western Waste Management Facility in Kincardine, Ontario, Canada. The older resins are contained in 3 m{sup 3} epoxy-coated cylindrical carbon steel containers known as resin liners. The liners are stored in a stacked configuration within cylindrical in-ground containers. Previous studies indicated evidence of unacceptable liner wall corrosion and the potential for eventual leakage of resin from the liners. Based on this, OPG elected to re-package the majority of the resin liners into stainless steel over-packs. A contract for this work was awarded to a project team consisting of Duratek of Canada, Kinectrics, Inc. and E.S. Fox. This paper provides an overall summary of project activities focusing on the effectiveness of the equipment utilized and the soundness of the developed programs, plans and procedures. Specific information is provided on key aspects of the project and the overall achievement of project goals. (authors)

Pearson, S.D. [EnergySolutions, Columbia, SC (Colombia); Husain, A. [Kinectrics, Toronto, Ontario (Canada)

2008-07-01T23:59:59.000Z

202

Comparison of Three Bed Packings for the Biological Removal of Nitric Oxide from Gas Streams  

Science Conference Proceedings (OSTI)

Environmental and health issues coupled with increasingly stringent nitrogen oxide (NOx) emission standards indicates a need for the development of alternative low-cost technologies for the removal of NOx from gas streams. Biological NOx conversion offers promise as a novel treatment method. Thermophilic denitrifying bacteria indigenous to composts and soils are capable of converting NOx to environmentally benign nitrogen via a dissimilatory reductive pathway. The present study compares the performance of three bioreactor packing materials (compost, perlite, and biofoam) for the removal of nitric oxide (NO) from a simulated wet-scrubbed combustion gas. Although all three materials performed well (>85% NO removal) at residence times of 70-80 seconds, the compost performed better than the other materials at shorter residence times (13-44 seconds). The perlite and biofoam materials, however, both offer long-term thermal stability and lower pressure drop compared with compost. The feasibility of biological NOx conversion processes will depend on the combined factors of NOx removal ability and pressure drop. The results presented here suggest that the compost, perlite and biofoam systems, subject to further optimization, offer potential for the biological removal of NOx from gas streams.

Lee, Brady Douglas; Flanagan, W. P.; Barnes, Charles Marshall; Barrett, Karen B.; Zaccardi, Larry Bryan; Apel, William Arnold

2000-10-01T23:59:59.000Z

203

2012 Rate Adjustments  

NLE Websites -- All DOE Office Websites (Extended Search)

Register Notices Meetings Brochure Brochure Addendum Customer Comment Letter Approved Rate Order FERC Confirmation If you have questions, call Rates and Repayment, 800-472-2306...

204

Rail Coal Transportation Rates  

U.S. Energy Information Administration (EIA)

figure data Figure 7 shows the percent change in average real rates for those state-to-state ... Estimated transportation rates for coal delivered to electric ...

205

Effective Rate Period  

NLE Websites -- All DOE Office Websites (Extended Search)

10012012 - 09302013 Mid-Year Changes (if applicable) 10012012 - 09302013 Power Rates Annual Revenue Requirement Rate Schedule Power Revenue Requirement 73,381,487...

206

Mesoporous TiO2-B Microspheres with Superior Rate Performance for Lithium Ion Batteries  

SciTech Connect

Mesoporous TiO2-B microsperes with a favorable material architecture are designed and synthesized for high power lithium ion batteries. This material, combining the advantages of fast lithium transport with a pseudocapacitive mechanism, adequate electrode-electrolyte contact and compact particle packing in electrode layer, shows superior high-rate charge-discharge capability and long-time cyclability for lithium ion batteries.

Liu, Hansan [ORNL; Bi, Zhonghe [ORNL; Sun, Xiao-Guang [ORNL; Unocic, Raymond R [ORNL; Paranthaman, Mariappan Parans [ORNL; Dai, Sheng [ORNL; Brown, Gilbert M [ORNL

2011-01-01T23:59:59.000Z

207

rates | OpenEI  

Open Energy Info (EERE)

rates rates Dataset Summary Description This dataset, compiled by NREL and Ventyx, provides average residential, commercial and industrial electricity rates by zip code for both investor owned utilities (IOU) and non-investor owned utilities. Note: the file includes average rates for each utility, but not the detailed rate structure data found in the database available via the zip-code look-up feature on the OpenEI Utilities page (http://en.openei.org/wiki/Gateway:Utilities). The data was released by NREL/Ventyx in February 2011. Source NREL and Ventyx Date Released February 24th, 2012 (2 years ago) Date Updated Unknown Keywords electric rates rates US utilities Data text/csv icon IOU rates by zipcode (csv, 1.7 MiB) text/csv icon Non-IOU rates by zipcode (csv, 2.1 MiB)

208

HTR-PROTEUS PEBBLE BED EXPERIMENTAL PROGRAM CORE 4: RANDOM PACKING WITH A 1:1 MODERATOR-TO-FUEL PEBBLE RATIO  

SciTech Connect

In its deployment as a pebble bed reactor (PBR) critical facility from 1992 to 1996, the PROTEUS facility was designated as HTR-PROTEUS. This experimental program was performed as part of an International Atomic Energy Agency (IAEA) Coordinated Research Project (CRP) on the Validation of Safety Related Physics Calculations for Low Enriched HTGRs. Within this project, critical experiments were conducted for graphite moderated LEU systems to determine core reactivity, flux and power profiles, reaction-rate ratios, the worth of control rods, both in-core and reflector based, the worth of burnable poisons, kinetic parameters, and the effects of moisture ingress on these parameters. One benchmark experiment was evaluated in this report: Core 4. Core 4 represents the only configuration with random pebble packing in the HTR-PROTEUS series of experiments, and has a moderator-to-fuel pebble ratio of 1:1. Three random configurations were performed. The initial configuration, Core 4.1, was rejected because the method for pebble loading, separate delivery tubes for the moderator and fuel pebbles, may not have been completely random; this core loading was rejected by the experimenters. Cores 4.2 and 4.3 were loaded using a single delivery tube, eliminating the possibility for systematic ordering effects. The second and third cores differed slightly in the quantity of pebbles loaded (40 each of moderator and fuel pebbles), stacked height of the pebbles in the core cavity (0.02 m), withdrawn distance of the stainless steel control rods (20 mm), and withdrawn distance of the autorod (30 mm). The 34 coolant channels in the upper axial reflector and the 33 coolant channels in the lower axial reflector were open. Additionally, the axial graphite fillers used in all other HTR-PROTEUS configurations to create a 12-sided core cavity were not used in the randomly packed cores. Instead, graphite fillers were placed on the cavity floor, creating a funnel-like base, to discourage ordering effects during pebble loading. Core 4 was determined to be acceptable benchmark experiment.

John D. Bess; Leland M. Montierth

2013-03-01T23:59:59.000Z

209

Historical Interest Rates  

NLE Websites -- All DOE Office Websites (Extended Search)

Current and Historical Interest Rates Current and Historical Interest Rates The table lists interest rates, from the project's inception through the present, for all projects with repayment supervised by the CRSP MC. The latest available interest rate is used for all future interest rate calculations. The Amistad-Falcon, Collbran, Provo River, and Rio Grande Projects are all assigned the average daily "Yield Rate" calculated by the U.S. Treasury, on an annual basis, for Treasury bonds having terms of 15 years or more remaining to maturity. The calculated yield rate is rounded to the nearest one-eighth of one percent. The yield rate is based upon the bond's interest rate, as well as its market value. The Colorado River Storage Project and its participating projects, Dolores and Seedskadee, are assigned the average daily "Coupon Rate," annualized for the same U.S. Treasury bonds used in "Yield Rate" calculations. The coupon rate is the interest rate that the bond carries upon its face.

210

Tracking the Libor Rate  

E-Print Network (OSTI)

Paper 1108R2 Paper 1108R) Tracking the Libor Rate Rosa M.revision 2013 by author(s). Tracking the Libor Rate Rosa M.providing a methodology for tracking the dynamic integrity

Abrantes-Metz, Rosa; Villas-Boas, Sofia B.; Judge, George G.

2013-01-01T23:59:59.000Z

211

2009 Rate Adjustments  

NLE Websites -- All DOE Office Websites (Extended Search)

provisional rates will be in effect until the Federal Energy Regulatory Commission (FERC) confirms and approves them on a final basis or until they are replaced by other rates....

212

Mouse heart rate  

NLE Websites -- All DOE Office Websites (Extended Search)

Mouse heart rate Name: amj Status: NA Age: NA Location: NA Country: NA Date: Around 1993 Question: Is it possible to get the heart rate of a mouse without special equipment?...

213

Dynamics of heart rate  

Science Conference Proceedings (OSTI)

Heart rate oscillates on several different time scales and has long?term variability in the form of 1/fnoise. The physiological control of heart rate is briefly reviewed

Daniel T. Kaplan; Mario Talajic

1991-01-01T23:59:59.000Z

214

Modeling the performance of the piston ring-pack with consideration of non-axisymmetric characteristics of the power cylinder system in internal combustion engines  

E-Print Network (OSTI)

The performance of the piston ring-pack is directly associated with the friction, oil consumption, wear, and blow-by in internal combustion engines. Because of non-axisymmetric characteristics of the power cylinder system, ...

Liu, Liang, 1971-

2005-01-01T23:59:59.000Z

215

About the Ratings  

NLE Websites -- All DOE Office Websites (Extended Search)

2008 Ratings Changes 2008 Ratings Changes EPA's "New" Fuel Economy Ratings Video about EPA's New Fuel Economy Ratings Windows Media Video (6.8 MB) Quicktime Video (7.8 MB) Text Version EPA changed the way it estimates fuel economy starting with the 2008 model year. This "new" way of estimating fuel economy supplements the previous method by incorporating the effects of Faster speeds and acceleration Air conditioner use Colder outside temperatures What else do I need to know about the "new" ratings? The tests lower MPG estimates for most vehicles. View old/new MPG ratings for a specific vehicle The actual mileage you get will still vary based on your driving habits, traffic conditions, and other factors. All MPG estimates in Find-a-Car have been converted to the new

216

Effective Rate Period  

NLE Websites -- All DOE Office Websites (Extended Search)

Fiscal Year 2014 Fiscal Year 2014 Effective Rate Period As of Beginning of the FY 10/01/2013 - 09/30/2014 Mid-Year Changes (if applicable) 10/01/2013 - 09/30/2014 Power Rates Annual Revenue Requirement Rate Schedule Power Revenue Requirement $73,441,557 CV-F13 Base Resource Revenue Requirement $69,585,875 First Preference Revenue Requirement $3,855,682

217

High Redshift Supernova Rates  

E-Print Network (OSTI)

We use a sample of 42 supernovae detected with the Advanced Camera for Surveys on-board the Hubble Space Telescope as part of the Great Observatories Origins Deep Survey to measure the rate of core collapse supernovae to z~0.7 and type Ia supernovae to z~1.6. This significantly increases the redshift range where supernova rates have been estimated from observations. The rate of core collapse supernovae can be used as an independent probe of the cosmic star formation rate. Based on the observations of 17 core collapse supernovae, we measure an increase in the core collapse supernova rate by a factor of 1.6 in the range 0.3rate. The increase in the rate in this redshift range in consistent with recent measurements of the star formation rate derived from UV-luminosity densities and IR datasets. Based on 25 type Ia supernovae, we find a SN Ia rate that is a factor 3-5 higher at z~1 compared to earlier estimates at lower redshifts (zrate traces a higher star formation rate at redshifts z>1 compared to low redshift. At higher redshift (z>1), we find a suggested decrease in the type Ia rate with redshift. This evolution of the Ia rate with redshift is consistent with a type Ia progenitor model where there is a substantial delay between the formation of the progenitor star and the explosion of the supernova. Assuming that the type Ia progenitor stars have initial main sequence masses 3-8 M_Sun, we find that 5-7% of the available progenitors explode as type Ia supernovae.

Tomas Dahlen; Louis-Gregory Strolger; Adam G. Riess; Bahram Mobasher; Ranga-Ram Chary; Christopher J. Conselice; Henry C. Ferguson; Andrew S. Fruchter; Mauro Giavalisco; Mario Livio; Piero Madau; Nino Panagia; John L. Tonry

2004-06-24T23:59:59.000Z

218

Rate Schedule CPP-2  

NLE Websites -- All DOE Office Websites (Extended Search)

or rate schedule accepted or approved by the Federal Energy Regulatory Commission (FERC) or other regulatory bodies will be passed on to each relevant customer. The FERC's or...

219

Exchange Rates and Fundamentals  

E-Print Network (OSTI)

We show analytically that in a rational expectations present-value model, an asset price manifests nearrandom walk behavior if fundamentals are I(1) and the factor for discounting future fundamentals is near one. We argue that this result helps explain the well-known puzzle that fundamental variables such as relative money supplies, outputs, inflation, and interest rates provide little help in predicting changes in floating exchange rates. As well, we show that the data do exhibit a related link suggested by standard modelsthat the exchange rate helps predict these fundamentals. The implication is that exchange rates and fundamentals are linked in a way that is broadly consistent with asset-pricing models of the exchange rate. I.

Charles Engel; Kenneth D. West

2005-01-01T23:59:59.000Z

220

High Rate and High Capacity Li-Ion Electrodes for Vehicular Applications  

Science Conference Proceedings (OSTI)

Significant advances in both energy density and rate capability for Li-ion batteries are necessary for implementation in electric vehicles. We have employed two different methods to improve the rate capability of high capacity electrodes. For example, we previously demonstrated that thin film high volume expansion MoO{sub 3} nanoparticle electrodes ({approx}2 {micro}m thick) have a stable capacity of {approx}630 mAh/g, at C/2 (charge/dicharge in 2 hours). By fabricating thicker conventional electrodes, an improved reversible capacity of {approx}1000 mAh/g is achieved, but the rate capability decreases. To achieve high-rate capability, we applied a thin Al{sub 2}O{sub 3} atomic layer deposition coating to enable the high volume expansion and prevent mechanical degradation. Also, we recently reported that a thin ALD Al{sub 2}O{sub 3} coating can enable natural graphite (NG) electrodes to exhibit remarkably durable cycling at 50 C. Additionally, Al{sub 2}O{sub 3} ALD films with a thickness of 2 to 4 {angstrom} have been shown to allow LiCoO{sub 2} to exhibit 89% capacity retention after 120 charge-discharge cycles performed up to 4.5 V vs. Li/Li{sup +}. Capacity fade at this high voltage is generally caused by oxidative decomposition of the electrolyte or cobalt dissolution. We have recently fabricated full cells of NG and LiCoO{sub 2} and coated both electrodes, one or the other electrode as well as neither electrode. In creating these full cells, we observed some surprising results that lead us to obtain a greater understanding of the ALD coatings. In a different approach we have employed carbon single-wall nanotubes (SWNTs) to synthesize binder-free, high-rate capability electrodes, with 95 wt.% active materials. In one case, Fe{sub 3}O{sub 4} nanorods are employed as the active storage anode material. Recently, we have also employed this method to demonstrate improved conductivity and highly improved rate capability for a LiNi{sub 0.4}Mn{sub 0.4}Co{sub 0.2}O{sub 2} cathode material. Raman spectroscopy was employed to understand how the SWNTs function as a highly flexible conductive additive.

Dillon, A. C.

2012-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "ah rated pack" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


221

HTR-PROTEUS Pebble Bed Experimental Program Cores 1, 1A, 2, and 3: Hexagonal Close Packing with a 1:2 Moderator-to-Fuel Pebble Ratio  

SciTech Connect

In its deployment as a pebble bed reactor (PBR) critical facility from 1992 to 1996, the PROTEUS facility was designated as HTR-PROTEUS. This experimental program was performed as part of an International Atomic Energy Agency (IAEA) Coordinated Research Project (CRP) on the Validation of Safety Related Physics Calculations for Low Enriched HTGRs. Within this project, critical experiments were conducted for graphite moderated LEU systems to determine core reactivity, flux and power profiles, reaction-rate ratios, the worth of control rods, both in-core and reflector based, the worth of burnable poisons, kinetic parameters, and the effects of moisture ingress on these parameters. Four benchmark experiments were evaluated in this report: Cores 1, 1A, 2, and 3. These core configurations represent the hexagonal close packing (HCP) configurations of the HTR-PROTEUS experiment with a moderator-to-fuel pebble ratio of 1:2. Core 1 represents the only configuration utilizing ZEBRA control rods. Cores 1A, 2, and 3 use withdrawable, hollow, stainless steel control rods. Cores 1 and 1A are similar except for the use of different control rods; Core 1A also has one less layer of pebbles (21 layers instead of 22). Core 2 retains the first 16 layers of pebbles from Cores 1 and 1A and has 16 layers of moderator pebbles stacked above the fueled layers. Core 3 retains the first 17 layers of pebbles but has polyethylene rods inserted between pebbles to simulate water ingress. The additional partial pebble layer (layer 18) for Core 3 was not included as it was used for core operations and not the reported critical configuration. Cores 1, 1A, 2, and 3 were determined to be acceptable benchmark experiments.

John D. Bess; Barbara H. Dolphin; James W. Sterbentz; Luka Snoj; Igor Lengar; Oliver Kberl

2012-03-01T23:59:59.000Z

222

OpenEI - rates  

Open Energy Info (EERE)

U.S. Electric Utility U.S. Electric Utility Companies and Rates: Look-up by Zipcode (Feb 2011) http://en.openei.org/datasets/node/899 This dataset, compiled by NREL and Ventyx, provides average residential, commercial and industrial electricity rates by zip code for both investor owned utilities (IOU) and non-investor owned utilities. Note: the file includes average rates for each utility, but not the detailed rate structure data found in the database available via the zip-code look-up feature on the OpenEI Utilities page (http://en.openei.org/wiki/Gateway:Utilities). The data was released by NREL/Ventyx in February 2011.

223

<RatesMiscInfo>  

NLE Websites -- All DOE Office Websites (Extended Search)

Rates MISCELLANEOUS INFORMATION Power Supply Report June 2013 (53kb pdf) May 2013 (53kb pdf) April 2013 (52kb pdf) March 2013 (54kb pdf) February 2013 (54kb pdf) January 2013 (54kb...

224

Heat Rate Program Guidelines  

Science Conference Proceedings (OSTI)

Power plant facilities with performance or heat rate improvement programs perform better than those that do not have those programs. A heat rate improvement program typically provides sufficient information for decision making with respect to timely maintenance actions and/or operational adjustments. Monitoring the performance of any power plant component includes the trending of parameters that also describe the performance of other plant components, providing insight and information on improving ...

2012-12-31T23:59:59.000Z

225

Cat Heart Rate Monitoring  

NLE Websites -- All DOE Office Websites (Extended Search)

Cat Heart Rate Monitoring Cat Heart Rate Monitoring Name: Shakti Status: student Grade: 9-12 Location: TX Country: USA Date: Summer 2010 Question: What is the best way to find a cat's heart rate using a stethoscope? Because I have tried to hear their heart beat but their purring is all I can hear. If I shouldn't use a stethoscope, then what should I use? Replies: Hi Shakti! If you want to use a stethoscope, the trick is to get your cat to stop purring. Two good ways that I have found to help stop the purring 1. Cover their nose (generally cats don't like this and will stop purring) or 2. Put on the tap to drip or lightly stream water (also, they generally don't like this and will stop purring). Alternatively, you can get their heart rate from feeling their pulse. A good place to try to feel a pulse is right where the leg attaches to the abdomen - in an area called the inguinal region. Now granted there are some heart conditions that will cause an animals pulse and their heart rates don't match up, and it's hard to feel if you have a fat cat, but it's a good place to try if you are really trying to get a heart rate in a healthy kitty!

226

untitled  

NLE Websites -- All DOE Office Websites (Extended Search)

Sonnenschein Sonnenschein Type: Sealed Lead Acid Number of Modules: 6 Weight of Pack: 191.4 kg Module Weight: 31.9 kg Nominal Module Voltage: 12 V Nominal System Voltage: 72 V Nominal Pack Capacity (C/3): 180 Ah Vehicle Specifications Manufacturer: 2008 Roush Industries Model: Roush Rev Year: 2008 Number of Motors 1 : 1 Motor Power Rating 2 : 150 kW VIN #: 9BFBT32N767991505 Static Capacity Test Measured Average Capacity: 156.0 Ah Measured Average Energy Capacity: 11.2 kWh Vehicle Mileage and Testing Date Vehicle Odometer: 6,000 mi Date of Test: May 28, 2009 Analysis Notes: 1. Motor refers to any motor capable of supplying traction power. 2. Motor power rating refers to the manufacturer's peak power rating for the motor(s) supplying traction power. 3. Calculated value based on selected battery voltage limits and at 50% SOC.

227

Trade, Interdependence and Exchange Rates  

E-Print Network (OSTI)

period is 1971-2000. All inflation rates and predictions areof Goods and Real Exchange Rate Fluc- tuations, mimeo [5]Between Trade and Exchange Rate Volatility, mimeo [6

Fitzgerald, Doireann

2004-01-01T23:59:59.000Z

228

Exchange Rates, Information, and Crises  

E-Print Network (OSTI)

3 Intervention and Exchange Rate Misalignment 4 Conclusion 5explain the exchange rate determination puzzle? Americanrisk to defend the exchange rate. Universitat Trier Working

Fernholz, Ricardo Turrin

2011-01-01T23:59:59.000Z

229

Mythology of rate design  

SciTech Connect

If power rates are determined by marginal costs with clear signals to the consumer, then the load curve will regulate itself without burdening the public with ethical and patriotic issues. Manipulation of the load factor will only cause hardship and inconvenience, but a choice of rates will allow consumers to determine their own balance between rates and convenience. It makes sense to charge consumers the true cost rather than having the same rate apply during a 24-hour period when costs are not uniform. Discussions of how to determine equitable rate structures flounder because we cannot define equity. Economists, who base their recommendations on the assumption that income distribution is reasonable, believe marginal-cost pricing allows the customer to save whatever the utility is saving. Such a system is economically efficient in that the utility charges 100 percent-load-factor consumers according to a base load plant, while charging peak and offpeak consumers what it costs to add them to the system. Adjustment of prices to cause a minimal distortion of the market is the economists' general rule for handling the balancing of cost increases and regulated profits. (DCK)

Streiter, S.H.

1977-01-01T23:59:59.000Z

230

BCP Annual Rate Process  

NLE Websites -- All DOE Office Websites (Extended Search)

2013 BCP Annual Rate Process 2013 BCP Annual Rate Process Informal Process Rate Activity Schedule (doc) Informal Customer Meeting Thursday March 6, 2013 at 10:30 A.M. Conf Rms 3&4 Informal Customer Meeting Presentation (Pdf) PRS Executive Summary (Mar 07, 2013) (Pdf) FY2014 Final Ten Year Operating Plan PRS Executive Summary (PDF) FORM for Foreign Visits (doc) Formal Process Initial Federal Register Notice (pdf) Public Information Forum March 27,2013 at 10:30 A.M. Conf Rms3&4 Customer Meeting Presentation PIF Presentation (PPT) Presentation Details (pdf) Reclamation Fund Status Report PIF PRS Executive Summary (pdf) PIF Transcripts (PDF) Visitor Center Cost Analysis Questions - Responses Public Comment Forum April 10, 2013 at 10:30 A.M. Conf Rms3&4 PCF Transcripts Customer Letters

231

Multiple System Rate Process  

NLE Websites -- All DOE Office Websites (Extended Search)

DSW Multiple System Transmission Rate Process DSW Multiple System Transmission Rate Process Federal Register Notice Withdrawing Rate Proposal (PDF) Formal Process Extension Federal Register Notice (PDF) Customer Savings Under Various MSTR (XLS) Public Information Forum March 29, 2005 Customer Meeting Overview (Power Point) Customer Meeting Overview (PDF) Customer Meeting Transcript (PDF) Public Comment Forum April 6, 2005 Customer Meeting Transcript (PDF) Response Letter 5-17-05 (PDF) Customer Letters Tonopah ID-5/25/05 (PDF) APS-5/26/05 (PDF) SRP-5/27/05 (PDF) RSLynch-6/1/05 (PDF) KRSaline-6/1/05 (PDF) Formal Process Federal Register Notice (Word) Federal Register Notice (PDF) Brochure (Word) Appendices to Brochure: A B C D E1 E2 F1 F2 GH Public Information Forum July 14, 2004 Customer Meeting Overview (Power Point)

232

Upper Great Plains Rates information  

NLE Websites -- All DOE Office Websites (Extended Search)

Rates and Repayment Services Rates and Repayment Services Rates 2010 Firm Power Rate (effective January 1, 2010) Rate Adjustments 2010 Firm Power Rate Adjustment 2009 Firm Power Rate Adjustment IS Rate Adjustments Rate Adjustment Process Rate Orders Signed, December 23, 2009 (16kb pdf) Announcements Firm Electric Service Customer Letter - Preliminary Review of Drought Adder Component, June 27, 2013 (74kb pdf) Customer Letter - Final Notice of Drought Adder Component, October 2, 2013 (68kb pdf) Integrated System (IS) Rates 2014 IS Rates Customer Information Meeting Presentation, October 15, 2013 (611kb pdf) Customer Letter - Notification of 2014 Rates, September 13, 2013 (160kb pdf) 2014 Transmission and Ancillary Services Rate Calculation and 2012 Rate True-up Calculation (4.9mb pdf) 2013 IS Rates

233

LAP Transmission Rate  

NLE Websites -- All DOE Office Websites (Extended Search)

LAP Transmission Rate 4.50 4.00 3.82 3.50 3.00 of 2.50 c 0 2.I2 2.68 I 3: 2.00 1.50 1.00 0.50 0.00 2000 2001 2002 2003 2004 2005 2006 2007 2008 2009 2010 2011 2012...

234

Natural Gas Conveyance and Rates  

Reports and Publications (EIA)

Natural gas transportation market; Competition vs. market power; Rate structures Cost-of-service Performance based rates

Information Center

2001-02-01T23:59:59.000Z

235

Rail Coal Transportation Rates  

U.S. Energy Information Administration (EIA) Indexed Site

reports reports Coal Transportation Rates to the Electric Power Sector With Data through 2010 | Release Date: November 16, 2012 | Next Release Date: December 2013 | Correction Previous editions Year: 2011 2004 Go Figure 1. Deliveries from major coal basins to electric power plants by rail, 2010 Background In this latest release of Coal Transportation Rates to the Electric Power Sector, the U.S. Energy Information Administration (EIA) significantly expands upon prior versions of this report with the incorporation of new EIA survey data. Figure 1. Percent of total U.S. rail shipments represented in data figure data Previously, EIA relied solely on data from the U.S. Surface Transportation Board (STB), specifically their confidential Carload Waybill Sample. While valuable, due to the statistical nature of the Waybill data,

236

Plant Tumor Growth Rates  

NLE Websites -- All DOE Office Websites (Extended Search)

Plant Tumor Growth Rates Plant Tumor Growth Rates Name: Gina and Maria Location: N/A Country: N/A Date: N/A Question: We are doing a science fair project on if B. Carotene, Green tea, and Grape Seed Extract helps plants against the crown gall disease. We injected sunflowers with agrobacterium tum. one week ago (Sun. Feb. 27, 2000). Our questions is how long will it take for the tumors to grow? We scratched the surface of the stems and injected the agrobacterium in the wound. Also which do you think, in your opinion, will do the best, if any? Our science fair is April 13, do you think we'll have growth before then, atleast enough time to do our conclusion and results? Thank you, any information you forward will be very helpful. Replies: Sunflowers form galls relatively quickly. I usually get them in two weeks at least. Good luck.

237

Adjusted Growth Rates*  

U.S. Energy Information Administration (EIA) Indexed Site

Jan. '99 to Feb. '99: -1.7% Feb. '98 to Feb. '99: +19.8% YTD '98 to YTD '99: +15.0% 4,100 4,400 4,700 5,000 5,300 5,600 5,900 Jan Feb Mar Apr May Jun Jul Aug Sep Oct Nov Dec Millions of Gallons U.S. Distillate Fuel Sales 2011 2012 2013 Adjusted Growth Rates* Jul '13 to Aug '13: 2.5% Aug '12 to Aug '13: -1.3% YTD '12 to YTD '13: 1.5% 300 400 500 600 700 800 900 Jan Feb Mar Apr May Jun Jul Aug Sep Oct Nov Dec Millions of Gallons U.S. Residual Fuel Sales 2011 2012 2013 Adjusted Growth Rates* Jul '13 to Aug '13: -0.8%

238

Adjusted Growth Rates* Jan.  

U.S. Energy Information Administration (EIA) Indexed Site

Adjusted Adjusted Growth Rates* Jan. '99 to Feb. '99: -1.7% Feb. '98 to Feb. '99: +19.8% YTD '98 to YTD '99: +15.0% U.S. Distillate Fuel Sales 3,000 3,500 4,000 4,500 5,000 5,500 Jan Feb Mar Apr May Jun Jul Aug Sep Oct Nov Dec Millions of Gallons 1998 1999 2000 Adjusted Growth Rates* Dec '99 to Jan '00: -7.4% Jan '99 to Jan '00: -0.1% YTD '99 to YTD '00: -0.1% U.S. Motor Gasoline Sales 8,000 9,000 10,000 11,000 12,000 Jan Feb Mar Apr May Jun Jul Aug Sep Oct Nov Dec Millions of Gallons 1998 1999 2000 Adjusted Growth Rates* Dec '99 to Jan '00: -16.8% Jan '99 to Jan '00: -3.2% YTD '99 to YTD '00: -3.2% U.S. Kerosene-Type Jet Fuel Sales 1,500 1,600 1,700 1,800 1,900 2,000 Jan Feb Mar Apr May Jun Jul Aug Sep Oct Nov Dec Millions of Gallons 1998 1999 2000 Adjusted Growth Rates* Dec '99 to Jan '00: -9.3% Jan '99 to Jan '00: +3.5% YTD '99 to YTD '00: +3.5% U.S. Propane Sales 600 800 1,000 1,200 1,400 1,600 1,800 Jan Feb Mar Apr May Jun Jul

239

Adjusted Growth Rates*  

U.S. Energy Information Administration (EIA) Indexed Site

July '99 to Aug. '99: +4.7% July '99 to Aug. '99: +4.7% Aug. '98 to Aug. '99: +1.3% YTD '98 to YTD '99: +4.7% U.S. Motor Gasoline Sales 8,000 9,000 10,000 11,000 12,000 Jan Feb Mar Apr May Jun Jul Aug Sep Oct Nov Dec Millions of Gallons 1997 1998 1999 Adjusted Growth Rates* July '99 to Aug. '99: -1.9% Aug. '98 to Aug. '99: -0.4% YTD '98 to YTD '99: +0.9% U.S. Kerosene-Type Jet Fuel Sales 1,500 1,600 1,700 1,800 1,900 2,000 Jan Feb Mar Apr May Jun Jul Aug Sep Oct Nov Dec Millions of Gallons 1997 1998 1999 Adjusted Growth Rates* July '99 to Aug. '99: -0.1% Aug. '98 to Aug. '99: -1.4% YTD '98 to YTD '99: -0.7% U.S. Propane Sales 600 800 1,000 1,200 1,400 1,600 1,800 Jan Feb Mar Apr May Jun Jul Aug Sep Oct Nov Dec Millions of Gallons 1997 1998 1999 Adjusted Growth Rates* July '99 to Aug. '99: +22.3% Aug. '98 to Aug. '99: +21.1%

240

Adjusted Growth Rates*  

U.S. Energy Information Administration (EIA) Indexed Site

Aug '99 to Sep '99: +4.9% Aug '99 to Sep '99: +4.9% Sep '98 to Sep '99: +4.7% YTD '98 to YTD '99: +4.7% U.S. Motor Gasoline Sales 8,000 9,000 10,000 11,000 12,000 Jan Feb Mar Apr May Jun Jul Aug Sep Oct Nov Dec Millions of Gallons 1997 1998 1999 Adjusted Growth Rates* Aug '99 to Sep '99: -2.4% Sep '98 to Sep '99: +0.4% YTD '98 to YTD '99: +1.3% U.S. Kerosene-Type Jet Fuel Sales 1,500 1,600 1,700 1,800 1,900 2,000 Jan Feb Mar Apr May Jun Jul Aug Sep Oct Nov Dec Millions of Gallons 1997 1998 1999 Adjusted Growth Rates* Aug '99 to Sep '99: -2.1% Sep '98 to Sep '99: +4.6% YTD '98 to YTD '99: 0.0% U.S. Propane Sales 600 800 1,000 1,200 1,400 1,600 1,800 Jan Feb Mar Apr May Jun Jul Aug Sep Oct Nov Dec Millions of Gallons 1997 1998 1999 Adjusted Growth Rates* Aug '99 to Sep '99: +7.3% Sep '98 to Sep '99: +8.4% YTD '98 to YTD '99: +8.3%

Note: This page contains sample records for the topic "ah rated pack" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


241

Adjusted Growth Rates*  

U.S. Energy Information Administration (EIA) Indexed Site

June '99 to July '99: -5.4% June '99 to July '99: -5.4% July '98 to July '99: +3.3% YTD '98 to YTD '99: +6.3% U.S. Motor Gasoline Sales 8,000 9,000 10,000 11,000 12,000 Jan Feb Mar Apr May Jun Jul Aug Sep Oct Nov Dec Millions of Gallons 1997 1998 1999 Adjusted Growth Rates* June '99 to July '99: -0.5% July '98 to July '99: -0.4% YTD '98 to YTD '99: +1.1% U.S. Kerosene-Type Jet Fuel Sales 1,500 1,600 1,700 1,800 1,900 2,000 Jan Feb Mar Apr May Jun Jul Aug Sep Oct Nov Dec Millions of Gallons 1997 1998 1999 Adjusted Growth Rates* June '99 to July '99: +0.5% July '98 to July '99: +1.0% YTD '98 to YTD '99: -0.3% U.S. Propane Sales 600 800 1,000 1,200 1,400 1,600 1,800 Jan Feb Mar Apr May Jun Jul Aug Sep Oct Nov Dec Millions of Gallons 1997 1998 1999 Adjusted Growth Rates* June '99 to July '99: +1.5% July '98 to July '99: +10.2% YTD '98 to YTD '99: +7.2%

242

Adjusted Growth Rates*  

U.S. Energy Information Administration (EIA) Indexed Site

Nov '99 to Dec '99: +5.3% Nov '99 to Dec '99: +5.3% Dec '98 to Dec '99: +8.7% YTD '98 to YTD '99: +5.0% U.S. Motor Gasoline Sales 8,000 9,000 10,000 11,000 12,000 Jan Feb Mar Apr May Jun Jul Aug Sep Oct Nov Dec Millions of Gallons 1997 1998 1999 Adjusted Growth Rates* Nov '99 to Dec '99: +6.0% Dec '98 to Dec '99: +4.5% YTD '98 to YTD '99: +1.3% U.S. Kerosene-Type Jet Fuel Sales 1,500 1,600 1,700 1,800 1,900 2,000 Jan Feb Mar Apr May Jun Jul Aug Sep Oct Nov Dec Millions of Gallons 1997 1998 1999 Adjusted Growth Rates* Nov '99 to Dec '99: +2.4% Dec '98 to Dec '99: +3.0% YTD '98 to YTD '99: +0.9% U.S. Propane Sales 600 800 1,000 1,200 1,400 1,600 1,800 Jan Feb Mar Apr May Jun Jul Aug Sep Oct Nov Dec Millions of Gallons 1997 1998 1999 Adjusted Growth Rates* Nov '99 to Dec '99: +32.3% Dec '98 to Dec '99: +2.0% YTD '98 to YTD '99: +5.5%

243

Adjusted Growth Rates*  

U.S. Energy Information Administration (EIA) Indexed Site

Oct '99 to Nov '99: +0.1% Oct '99 to Nov '99: +0.1% Nov '98 to Nov '99: +5.5% YTD '98 to YTD '99: +4.5% U.S. Motor Gasoline Sales 8,000 9,000 10,000 11,000 12,000 Jan Feb Mar Apr May Jun Jul Aug Sep Oct Nov Dec Millions of Gallons 1997 1998 1999 Adjusted Growth Rates* Oct '99 to Nov '99: -0.7% Nov '98 to Nov '99: +1.7% YTD '98 to YTD '99: +1.1% U.S. Kerosene-Type Jet Fuel Sales 1,500 1,600 1,700 1,800 1,900 2,000 Jan Feb Mar Apr May Jun Jul Aug Sep Oct Nov Dec Millions of Gallons 1997 1998 1999 Adjusted Growth Rates* Oct '99 to Nov '99: +2.5% Nov '98 to Nov '99: +6.0% YTD '98 to YTD '99: +0.8% U.S. Propane Sales 600 800 1,000 1,200 1,400 1,600 1,800 Jan Feb Mar Apr May Jun Jul Aug Sep Oct Nov Dec Millions of Gallons 1997 1998 1999 Adjusted Growth Rates* Oct '99 to Nov '99: +9.7% Nov '98 to Nov '99: +2.2% YTD '98 to YTD '99: +6.2%

244

Adjusted Growth Rates*  

U.S. Energy Information Administration (EIA) Indexed Site

Sep '99 to Oct '99: +3.9% Sep '99 to Oct '99: +3.9% Oct '98 to Oct '99: +2.3% YTD '98 to YTD '99: +4.4% U.S. Motor Gasoline Sales 8,000 9,000 10,000 11,000 12,000 Jan Feb Mar Apr May Jun Jul Aug Sep Oct Nov Dec Millions of Gallons 1997 1998 1999 Adjusted Growth Rates* Sep '99 to Oct '99: -0.2% Oct '98 to Oct '99: -0.9% YTD '98 to YTD '99: +1.0% U.S. Kerosene-Type Jet Fuel Sales 1,500 1,600 1,700 1,800 1,900 2,000 Jan Feb Mar Apr May Jun Jul Aug Sep Oct Nov Dec Millions of Gallons 1997 1998 1999 Adjusted Growth Rates* Sep '99 to Oct '99: -1.9% Oct '98 to Oct '99: -0.7% YTD '98 to YTD '99: +0.4% U.S. Propane Sales 600 800 1,000 1,200 1,400 1,600 1,800 Jan Feb Mar Apr May Jun Jul Aug Sep Oct Nov Dec Millions of Gallons 1997 1998 1999 Adjusted Growth Rates* Sep '99 to Oct '99: -2.1% Oct '98 to Oct '99: -6.4% YTD '98 to YTD '99: +6.6%

245

A two-stage tabu search algorithm with enhanced packing heuristics for the 3L-CVRP and M3L-CVRP  

Science Conference Proceedings (OSTI)

The Three-Dimensional Loading Capacitated Vehicle Routing Problem (3L-CVRP) addresses practical constraints frequently encountered in the freight transportation industry. In this problem, the task is to serve all customers using a homogeneous fleet of ... Keywords: 3D packing, Deepest-Bottom-Left-Fill, Maximum Touching Area, Tabu search, Vehicle routing problem

Wenbin Zhu; Hu Qin; Andrew Lim; Lei Wang

2012-09-01T23:59:59.000Z

246

Rate Adjustments and Public Involvement  

NLE Websites -- All DOE Office Websites (Extended Search)

Rate Adjustments and Public Involvement Documents Rate Adjustments and Public Involvement Documents CRSP Transmission 9/16/2013 WAPA-161 FRN, CRSP transmission and ancillary services rates extension Letter announcing two-year extension to CRSP transmission and ancillary services rates Letter announcing revised CRSP transmission rates for FY 2014 Accompanying calculation table for FY 2014 CRSP transmission rate letter Letter announcing revised CRSP transmission rates for FY 2013 Letter announcing revised CRSP transmission rates for FY 2012 Letter announcing revised CRSP transmission rates for FY 2011 Letter announcing revised CRSP transmission rates for FY 2010 SLCA/IP 9/16/2013 WAPA-161 FRN, SLCA/IP firm power rate extension Letter announcing two-year extension to SLCA/IP firm power rate SLCA/IP Tentative Rate Adjustment Schedule

247

PULSE RATE DIVIDER  

DOE Patents (OSTI)

A compact pulse-rate divider circuit affording low impedance output and high input pulse repetition rates is described. The circuit features a single secondary emission tube having a capacitor interposed between its dynode and its control grid. An output pulse is produced at the anode of the tube each time an incoming pulse at the control grid drives the tube above cutoff and the duration of each output pulse corresponds to the charging time of the capacitor. Pulses incoming during the time the grid bias established by the discharging capacitor is sufficiently negative that the pulses are unable to drive the tube above cutoff do not produce output pulses at the anode; these pulses are lost and a dividing action is thus produced by the circuit. The time constant of the discharge path may be vanied to vary in turn the division ratio of the circuit; the time constant of the charging circuit may be varied to vary the width of the output pulses. (AEC)

McDonald, H.C. Jr.

1962-12-18T23:59:59.000Z

248

Survey of innovative rates, 1991  

SciTech Connect

Current innovative rate data from 135 major utilities throughout the United States were gathered and analyzed. Over 1000 innovative rates that were in use by the utilities in 1990 and 1991 were identified, abstracted and entered into a database. Survey results indicate that over 616 million MWh were sold to the nearly five million customers using the innovative rates offered. From an annual sales perspective, the most widely used rates are demand-side management rates -- rates intended to change customer energy use -- and rates that are market-driven.'' The survey identified 525 demand-side management rates serving our four million customers with reported sales of approximately 520 million MWh. These rates serve over 80% of the total innovative rate customers and account for 84% of the total MWh sales. Also important in terms of MWh sales they represent are market-driven rates, which accounted for sales of 48 million MWh in 1990. Both demand-side management and market-driven rates show a 20% customer growth rate between 1988 and 1990. Other innovative rates examined in the survey included: prepaid service; load retention incentive rates; technology specific rates; and those rates related expressly to non-utility generators -- namely buy-back and standby rates.

White, L.J.; Wakefield, R.A.; McVicker, C.M.

1992-04-01T23:59:59.000Z

249

Survey of innovative rates, 1991  

Science Conference Proceedings (OSTI)

Current innovative rate data from 135 major utilities throughout the United States were gathered and analyzed. Over 1000 innovative rates that were in use by the utilities in 1990 and 1991 were identified, abstracted and entered into a database. Survey results indicate that over 616 million MWh were sold to the nearly five million customers using the innovative rates offered. From an annual sales perspective, the most widely used rates are demand-side management rates -- rates intended to change customer energy use -- and rates that are market-driven.'' The survey identified 525 demand-side management rates serving our four million customers with reported sales of approximately 520 million MWh. These rates serve over 80% of the total innovative rate customers and account for 84% of the total MWh sales. Also important in terms of the MWh sales they represent are market-driven rates, which accounted for sales of 48 million MWh in 1990. Both demand-side management and market-driven rates show a 20% customer growth rate between 1988 and 1990. Other innovative rates examined in the survey included: prepaid service; load retention incentive rates; technology specific rates; and those rates related expressly to non-utility generators -- namely buy-back and standby rates.

White, L.J.; Wakefield, R.A.; McVicker, C.M.

1992-04-01T23:59:59.000Z

250

Adsorption and desorption of noble gases on activated charcoal: I. sup 133 Xe studies in a monolayer and packed bed  

SciTech Connect

Detailed desorption studies using petroleum-based activated charcoals were conducted in monolayers and packed beds. Less extensive studies were conducted on several other types of charcoal. Kinetic studies, using {sup 133}Xe, demonstrated the existence of a micropore volume with entrance capillaries that together determined the response characteristics of charcoal to external concentration gradients of tracer gases. This new two-phase model, composed of micropores and entrance capillaries, describes the desorption dynamics of an adsorbed gas in the presence of water vapor. Condensed water vapor in the entrance capillaries of the charcoal reduced the effective pore radius and increased the diffusion half-time. Water could also adversely affect the integrating capability of the charcoal dramatically if the adsorbed water completely blocked the entrance capillaries. The amount of adsorbed water required to block the capillaries varied with the charcoal type and was termed here as the break-point. The desorption parameters measured in this work can be used to design an improved passive Rn monitor to effectively integrate during a 3-7 d exposure period by eliminating the adverse effects of water vapor. The improved canister design would provide more accurate and reproducible measurements of indoor Rn concentrations than are currently available.

Scarpitta, S.C.; Harley, N.H. (Department of Energy, New York, NY (USA))

1990-10-01T23:59:59.000Z

251

VEHICLE DETAILS AND BATTERY SPECIFICATIONS  

NLE Websites -- All DOE Office Websites (Extended Search)

RRXDF106605 RRXDF106605 Hybrid Propulsion System: Mild Parallel Belt-Alternator Starter (BAS) Number of Electric Machines: 1 Motor: 15 kW (peak), AC induction Battery Specifications Manufacturer: Hitachi Type: Cylindrical Lithium-ion Number of Cells: 32 Nominal Cell Voltage: 3.6 V Nominal System Voltage: 115.2 V Rated Pack Capacity: 4.4 Ah Maximum Cell Charge Voltage 2 : 4.10 V Minimum Cell Discharge Voltage 2 : 3.00 V Thermal Management: Active - Forced air Pack Weight: 65 lb BEGINNING-OF-TEST: BATTERY LABORATORY TEST RESULTS SUMMARY Vehicle Mileage and Testing Date Vehicle Odometer: 4,244 mi Date of Test: January 9, 2013 Static Capacity Test Measured Average Capacity: 3.88 Ah Measured Average Energy Capacity: 450 Wh HPPC Test Pulse Discharge Power @ 50% DOD

252

VEHICLE DETAILS AND BATTERY SPECIFICATIONS  

NLE Websites -- All DOE Office Websites (Extended Search)

RR0DF106791 RR0DF106791 Hybrid Propulsion System: Mild Parallel Belt-Alternator Starter (BAS) Number of Electric Machines: 1 Motor: 15 kW (peak), AC induction Battery Specifications Manufacturer: Hitachi Type: Cylindrical Lithium-ion Number of Cells: 32 Nominal Cell Voltage: 3.6 V Nominal System Voltage: 115.2 V Rated Pack Capacity: 4.4 Ah Maximum Cell Charge Voltage 2 : 4.10 V Minimum Cell Discharge Voltage 2 : 3.00 V Thermal Management: Active - Forced air Pack Weight: 65 lb BEGINNING-OF-TEST: BATTERY LABORATORY TEST RESULTS SUMMARY Vehicle Mileage and Testing Date Vehicle Odometer: 5,715 mi Date of Test: January 8, 2013 Static Capacity Test Measured Average Capacity: 3.98 Ah Measured Average Energy Capacity: 460 Wh HPPC Test Pulse Discharge Power @ 50% DOD

253

Thermal Characterization and Analysis of A123 Systems Battery Cells, Modules and Packs: Cooperative Research and Development Final Report, CRADA Number CRD-07-243  

DOE Green Energy (OSTI)

In support of the A123 Systems battery development program with USABC/DOE, NREL provided technical support in thermal characterization, analysis and management of batteries. NREL's effort was part of Energy Storage Project funded by DOE Vehicle Technologies Program. The purpose of this work was for NREL to perform thermal characterization and analysis of A123 Systems cells and modules with the aim for Al23 Systems to improve the thermal performance of their battery cells, modules and packs.

Pesaran, A.

2012-03-01T23:59:59.000Z

254

electric rates | OpenEI  

Open Energy Info (EERE)

electric rates electric rates Dataset Summary Description This dataset, compiled by NREL and Ventyx, provides average residential, commercial and industrial electricity rates by zip code for both investor owned utilities (IOU) and non-investor owned utilities. Note: the file includes average rates for each utility, but not the detailed rate structure data found in the database available via the zip-code look-up feature on the OpenEI Utilities page (http://en.openei.org/wiki/Gateway:Utilities). The data was released by NREL/Ventyx in February 2011. Source NREL and Ventyx Date Released February 24th, 2012 (2 years ago) Date Updated Unknown Keywords electric rates rates US utilities Data text/csv icon IOU rates by zipcode (csv, 1.7 MiB) text/csv icon Non-IOU rates by zipcode (csv, 2.1 MiB)

255

Rate Schedules | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Rate Schedules Rate Schedules Rate Schedules One of the major responsibilities of Southeastern is to design, formulate, and justify rate schedules. Repayment studies prepared by the agency determine revenue requirements and appropriate rate levels and these studies for each of Southeastern's four power marketing systems are updated annually. They demonstrate the adequacy of the rates for each system. Rates are considered to be adequate when revenues are sufficient to repay all costs associated with power production and transmission costs, which include the amortization of the Federal investment allocated to power. Latest Rate Schedules October 1, 2012 ALA-1-N Wholesale Power Rate Schedule Area: PowerSouth Energy Cooperative System: Georgia-Alabama-South Carolina October 1, 2012

256

Pack.PDF  

NLE Websites -- All DOE Office Websites (Extended Search)

February 1999 February 1999 Revised: 05/05/99 CHEVROLET S-10 ELECTRIC (NIMH BATTERIES) PERFORMANCE CHARACTERIZATION SUMMARY ELECTRIC TRANSPORTATION DIVISION Urban Range (On Urban Pomona Loop - see other side for map) Test UR1 UR2 UR3 UR4 Payload (lb.) 180 180 920 920 AC kWh Recharge 54.93 57.09 54.98 51.34 AC kWh/mi. 0.78 0.91 0.87 0.85 Range (mi.) 70.4 63.0 63.0 60.4 Avg. Ambient Temp. 63°F 66°F 63°F 50°F UR1 Urban Range Test, Min Payload, No Auxiliary Loads UR2 Urban Range Test, Min Payload, A/C on High, Headlights on Low, Radio On UR3 Urban Range Test, Max Payload, No Auxiliary Loads UR4 Urban Range Test, Max Payload, A/C on High, Headlights on Low, Radio On State of Charge Meter (UR1) Freeway Range (On Freeway Pomona Loop - see other side for map) Test FW1 FW2 FW3 FW4 Payload (lb.) 180 180 920 920 AC kWh Recharge

257

DataPackInvrpt  

Office of Legacy Management (LM)

7. The samples were prepared and analyzed within the established hold times. All in house quality control procedures were followed, as described below. 8. General quality...

258

Approximating semidefinite packing programs ?  

E-Print Network (OSTI)

Proceedings of the 35th Annual Symposium on Foundations of Computer Science, Washington, DC,. USA, 1994, IEEE Computer Society, pp. 3639.

259

bin packing problem  

Science Conference Proceedings (OSTI)

... For instance, suppose we need a number of pipes of different, specific lengths to plumb a house and we can buy pipe stock in 5 meter lengths. ...

2013-08-23T23:59:59.000Z

260

National Utility Rate Database: Preprint  

DOE Green Energy (OSTI)

When modeling solar energy technologies and other distributed energy systems, using high-quality expansive electricity rates is essential. The National Renewable Energy Laboratory (NREL) developed a utility rate platform for entering, storing, updating, and accessing a large collection of utility rates from around the United States. This utility rate platform lives on the Open Energy Information (OpenEI) website, OpenEI.org, allowing the data to be programmatically accessed from a web browser, using an application programming interface (API). The semantic-based utility rate platform currently has record of 1,885 utility rates and covers over 85% of the electricity consumption in the United States.

Ong, S.; McKeel, R.

2012-08-01T23:59:59.000Z

Note: This page contains sample records for the topic "ah rated pack" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


261

Operational dose rate visualization techniques  

SciTech Connect

The analysis of the gamma ray dose rate in the vicinity of a radiation source can be greatly aided by the use of recent state-of-the-art visualization techniques. The method involves calculating dose rates at thousands of locations within a complex geometry system. This information is then processed to create contour plots of the dose rate. Additionally, when these contour plots are created, animations can be created that dynamically display the dose rate as the shields or sources are moved.

Schwarz, R.A.; Morford, R.J.; Carter, L.L.; Jones, G.B.; Greenborg, J.

1994-01-01T23:59:59.000Z

262

DOE Guidance-Category Rating  

Energy.gov (U.S. Department of Energy (DOE))

This memorandum is to establish the Department of Energy's (DOE's) policy for the use of Category Rating.

263

ARCS Access Rate Control System  

protected steel housing. ... Access Rate Control System This rugged, maintenance- ... Y-12 is seeking an industry partner to fully com-

264

Asymptotic Cellular Growth Rate as the Effective Information Utilization Rate  

E-Print Network (OSTI)

We study the average asymptotic growth rate of cells in randomly fluctuating environments. Using a game-theoretic perspective, we show that any response strategy has an asymptotic growth rate, which is the sum of: (i) the maximal growth rate at the worst possible distribution of environments, (ii) relative information between the actual distribution of environments to the worst one, and (iii) information utilization rate which is the information rate of the sensory devices minus the "information dissipation rate", the amount of information not utilized by the cell for growth. In non-stationary environments, the optimal strategy is the time average of the instantaneous optimal strategy and the optimal switching times are evenly spaced in the statistical (Fisher) metric.

Pugatch, Rami; Tlusty, Tsvi

2013-01-01T23:59:59.000Z

265

2011 Heat Rate Improvement Conference  

Science Conference Proceedings (OSTI)

With the rising cost of fuel and the strong possibility of CO2 emissions regulations and limitations in the near future, utilities and power generation companies are focusing on power plant heat rate and performance. The Electric Power Research Institute (EPRI) 17th Heat Rate Improvement Conference is the latest in a series of meetings designed to assist attendees in addressing problems with power plant performance and in identifying cost-effective solutions for achieving and sustaining heat rate improve...

2011-03-28T23:59:59.000Z

266

Search Results for 'Credit Rating'  

U.S. Energy Information Administration (EIA)

The rating agency says it expects the banks asset quality to remain weak over the next 12-18 months

267

Exchange rate determination in Indonesia.  

E-Print Network (OSTI)

??This thesis examines the options for adopting normative and prescriptive models of exchange rate determination suitable for developed and developing countries. It also develops a (more)

Rusydi, Mohammad

2006-01-01T23:59:59.000Z

268

Definition: Rating | Open Energy Information  

Open Energy Info (EERE)

power, such as transformers, or transport it from one location to another, such as transmission lines, the power rating almost always refers to the maximum power flow...

269

Sustainable Building Rating Systems Summary  

SciTech Connect

The purpose of this document is to offer information that could be used to compare and contrast sustainable building rating systems.

Fowler, Kimberly M.; Rauch, Emily M.

2006-07-01T23:59:59.000Z

270

June 1 Government Rate $137  

NLE Websites -- All DOE Office Websites (Extended Search)

& Fitness Center The Jewelry Box & Gift Shoppe 24 Hour Front Desk Service, Sundry Shop, ATM Wireless Internet Always Complimentary 112 per night room rate effective thru April...

271

VEHICLE SPECIFICATIONS  

NLE Websites -- All DOE Office Websites (Extended Search)

Page 1 of 5 Page 1 of 5 VEHICLE SPECIFICATIONS 1 Vehicle Features Base Vehicle: 2011 Nissan Leaf VIN: JN1AZ0CP5BT000356 Class: Mid-size Seatbelt Positions: 5 Type: EV Motor Type: Three-Phase, Four-Pole Permanent Magnet AC Synchronous Max. Power/Torque: 80 kW/280 Nm Max. Motor Speed: 10,390 rpm Cooling: Active - Liquid cooled Battery Manufacturer: Automotive Energy Supply Corporation Type: Lithium-ion - Laminate type Cathode/Anode Material: LiMn 2 O 4 with LiNiO 2 /Graphite Pack Location: Under center of vehicle Number of Cells: 192 Cell Configuration: 2 parallel, 96 series Nominal Cell Voltage: 3.8 V Nominal System Voltage: 364.8 V Rated Pack Capacity: 66.2 Ah Rated Pack Energy: 24 kWh Max. Cell Charge Voltage 2 : 4.2 V Min. Cell Discharge Voltage 2 : 2.5 V

272

VEHICLE SPECIFICATIONS  

NLE Websites -- All DOE Office Websites (Extended Search)

VEHICLE SPECIFICATIONS 1 Vehicle Features Base Vehicle: 2011 Chevrolet Volt VIN: 1G1RD6E48BUI00815 Class: Compact Seatbelt Positions: 4 Type 2 : Multi-Mode PHEV (EV, Series, and Power-split) Motor Type: 12-pole permanent magnet AC synchronous Max. Power/Torque: 111 kW/370 Nm Max. Motor Speed: 9500 rpm Cooling: Active - Liquid cooled Generator Type: 16-pole permanent magnet AC synchronous Max. Power/Torque: 55 kW/200 Nm Max. Generator Speed: 6000 rpm Cooling: Active - Liquid cooled Battery Manufacturer: LG Chem Type: Lithium-ion Cathode/Anode Material: LiMn 2 O 4 /Hard Carbon Number of Cells: 288 Cell Config.: 3 parallel, 96 series Nominal Cell Voltage: 3.7 V Nominal System Voltage: 355.2 V Rated Pack Capacity: 45 Ah Rated Pack Energy: 16 kWh Weight of Pack: 435 lb

273

Server efficiency rating tool (SERT)  

Science Conference Proceedings (OSTI)

The Server Efficiency Rating Tool (SERT) [1] has been developed by Standard Performance Evaluation Corporation (SPEC) [2] at the request of the US Environmental Protection Agency (EPA) [3], prompted by concerns that US datacenters consumed almost 3% ... Keywords: benchmark, datacenter, energy efficiency, energy star, environmental protection agency, epa, power, rating tool, sert, server, spec

Klaus-Dieter Lange; Mike G. Tricker; Jeremy A. Arnold; Hansfried Block; Sanjay Sharma

2012-04-01T23:59:59.000Z

274

Commercial Building Asset Rating Program  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

1 eere.energy.gov 1 eere.energy.gov Commercial Building Asset Rating Program August 23, 2011 12 p.m. ET, 9 a.m. PT Presenter: Cody Taylor PRE-DECISIONAL Information included in this document is for discussion purposes and does not constitute the final program design. FOR INFORMATION ONLY 2 eere.energy.gov Outline * Goals * Scope & schedule * Guiding principles * Program design issues - Metrics - Rating method - Rating scale - Opportunities for efficiency improvement - Quality assurance Please submit clarifying questions during today's webinar via the Q&A function of Live Meeting. 3 eere.energy.gov National Building Rating Program Goals * Facilitate cost-effective investment in energy efficiency and reduce energy use in the commercial building sector * Establish a national standard for voluntary commercial building asset rating

275

Supernova rates and stellar populations  

E-Print Network (OSTI)

We discuss the results about the nature of type Ia Supernovae that can be derived by studying their rates in different stellar populations. While the evolution of SN photometry and spectra can constrain the explosion mechanism, the SN rate depends on the progenitor system. We review the current available data on rates as a function of parent galaxy color, morphology, star formation rate, radio luminosity and environment. By studying the variation of the rates with the color of the parent galaxy, a strong evidence was established that type Ia SNe come from both young and old stars. The dependence of the rates with the radio power of the parent galaxy is best reproduced by a bimodal distribution of delay time between the formation of the progenitor and its explosion as a SN. Cluster early-type galaxies show higher type Ia SN rate with respect to field galaxies, and this effect can be due either to traces of young stars or to differences in the delay time distribution.

F. Mannucci

2007-08-03T23:59:59.000Z

276

OpenEI - electric rates  

Open Energy Info (EERE)

U.S. Electric Utility U.S. Electric Utility Companies and Rates: Look-up by Zipcode (Feb 2011) http://en.openei.org/datasets/node/899 This dataset, compiled by NREL and Ventyx, provides average residential, commercial and industrial electricity rates by zip code for both investor owned utilities (IOU) and non-investor owned utilities. Note: the file includes average rates for each utility, but not the detailed rate structure data found in the database available via the zip-code look-up feature on the OpenEI Utilities page (http://en.openei.org/wiki/Gateway:Utilities). The data was released by NREL/Ventyx in February 2011.

277

DOE Guidance-Category Rating  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

2010 2010 MEMORANDUM FOR HUMAN RESOURCES DIRECTORS FROM: SARA"iJ. Boku1, DIRECToR OF HUMAN C~TAL MANAGEMENT SUBJECT: GUIDANCE MEMORANDUM #10 CATEGORY RATING The purpose of this memorandum is to establish the Department of Energy's (DOE's) policy for the use of Category Rating. Authorities: Public Law 107-296; Title 5 USC 3319; 5 CFR, Part 337, Subpart C., Presidential Memorandum of May 11, 2010 This guidance is established in accordance with 5 USC 3319, which authorizes Federal Agencies to use alternative rating proced.ures in assessing applicants for employment using category rating and selection procedures, and to ensure consistency in complying with federal regulations contained in the Code of Federal Regulations (CFR), Office of Personnel Management (OPM) and the Department of

278

ARM - Measurement - Radiative heating rate  

NLE Websites -- All DOE Office Websites (Extended Search)

govMeasurementsRadiative heating rate govMeasurementsRadiative heating rate ARM Data Discovery Browse Data Comments? We would love to hear from you! Send us a note below or call us at 1-888-ARM-DATA. Send Measurement : Radiative heating rate The heating rate due to the divergence of long and shortwave radiative flux. Categories Radiometric, Atmospheric State Instruments The above measurement is considered scientifically relevant for the following instruments. Refer to the datastream (netcdf) file headers of each instrument for a list of all available measurements, including those recorded for diagnostic or quality assurance purposes. External Instruments MOLTS : Model Output Location Time Series Datastreams MOLTS : Model Output Location Time Series Datastreams MOLTSEDASSNDCLASS1 : Model Output Loc. Time Ser. (MOLTS): EDAS

279

Heat Rate Improvement Reference Manual  

Science Conference Proceedings (OSTI)

Performance optimization of fossil power plants is a high priority within the electric utilities in the new competitive environment. This manual can help utility engineers establish a heat rate improvement program.

1998-07-27T23:59:59.000Z

280

Project Definition Rating Index (PDRI)  

Energy.gov (U.S. Department of Energy (DOE))

The Office of Environmental Management (EM) Project Definition Rating Index (EM-PDRI) is a modification of a commercially developed planning tool that has been tested by an EM team specifically for...

Note: This page contains sample records for the topic "ah rated pack" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


281

High compression rate text summarization  

E-Print Network (OSTI)

This thesis focuses on methods for condensing large documents into highly concise summaries, achieving compression rates on par with human writers. While the need for such summaries in the current age of information overload ...

Branavan, Satchuthananthavale Rasiah Kuhan

2008-01-01T23:59:59.000Z

282

Exchange Rates, Information, and Crises  

E-Print Network (OSTI)

equation (5.4). Standard Bayesian inference implies that theAs before, standard Bayesian inference implies that Var 1 [f so that standard Bayesian inference both exchange rate is

Fernholz, Ricardo Turrin

2011-01-01T23:59:59.000Z

283

A Successful Cool Storage Rate  

E-Print Network (OSTI)

Houston Lighting & Power (HL&P) initiated design and development of its commercial cool storage program as part of an integrated resource planning process with a targeted 225 MW of demand reduction through DSM. Houston's extensive commercial air conditioning load, which is highly coincident with HL&P's system peak, provided a large market for cool storage technologies. Initial market research made it very clear that a special cool storage rate was required to successfully market the technology. Development of the rate required an integrated, multidepartment effort and extensive use of DSManager, an integrated resource planning model. An experimental version of the rate was initially implemented as part of the initial phase of the cool storage program. A permanent rate, incorporating lessons learned from the experimental rate, was then developed for the long term implementation of the program. The permanent rate went through a lengthy regulatory approval process which included intervention by a local natural gas distribution company. The end result is a very successful cool storage program with 52 projects and 31 megawatts of demand reduction in the first three and one-half years of program implementation.

Ahrens, A. C.; Sobey, T. M.

1994-01-01T23:59:59.000Z

284

High-Energy Threshold Reaction Rates on 0.8 GeV Proton-Irradiated Thick W and W-Na Targets  

E-Print Network (OSTI)

Threshold activation reaction rates in 12C, 19F, 27Al, 59Co, 63Cu, 65Cu, 64Zn, 93Nb, 115In, 169Tm, 181Ta, 197Au, and 209Bi experimental samples placed along the axis inside and outside the 0.8 GeV proton-irradiated 92-cm thick W-Na and 4-cm thick W targets where measured at the ITEP proton synchrotron. 158 reactions of up to +AH4-0.5 GeV thresholds have been measured in 123 activation samples for W-Na target, and 157 reactions in 36 activation samples for W target. The reaction rates were determined using the gamma-spectrometry method. In total, more than 1000 values of activation reactions were determined in the experiments. In both cases the measured reaction rates were compared with the LAHET code simulated rates and using several nuclear databases for the respective excitation functions, namely, ENDF/B6 for cross section of neutrons at energies below 20 MeV and MENDL2 together with MENDL2P for cross sections of protons and neutrons of 20 to 100 MeV energies. A general satisfactory agreement between simulated and experimental data has been found.

Yu. E. Titarenko; V. F. Batyaev; E. I. Karpikhin; V. M. Zhivun; A. B. Koldobsky; R. D. Mulambetov; S. V. Mulambetova; S. L. Zaitsev; S. G. Mashnik; R. E. Prael

2004-01-26T23:59:59.000Z

285

Standard Rates, Budget Office, Brookhaven National Laboratory...  

NLE Websites -- All DOE Office Websites (Extended Search)

Standard Rates Standard Rates for Brookhaven National Laboratory is available in PDF file formats. This file contains rates for Distributed Technical Services, Scientific Devices...

286

LINEAR COUNT-RATE METER  

DOE Patents (OSTI)

A linear count-rate meter is designed to provide a highly linear output while receiving counting rates from one cycle per second to 100,000 cycles per second. Input pulses enter a linear discriminator and then are fed to a trigger circuit which produces positive pulses of uniform width and amplitude. The trigger circuit is connected to a one-shot multivibrator. The multivibrator output pulses have a selected width. Feedback means are provided for preventing transistor saturation in the multivibrator which improves the rise and decay times of the output pulses. The multivibrator is connected to a diode-switched, constant current metering circuit. A selected constant current is switched to an averaging circuit for each pulse received, and for a time determined by the received pulse width. The average output meter current is proportional to the product of the counting rate, the constant current, and the multivibrator output pulse width.

Henry, J.J.

1961-09-01T23:59:59.000Z

287

Coal Transportation Rate Sensitivity Analysis  

Reports and Publications (EIA)

On December 21, 2004, the Surface Transportation Board (STB) requested that the Energy Information Administration (EIA) analyze the impact of changes in coal transportation rates on projected levels of electric power sector energy use and emissions.Specifically, the STB requested an analysis of changes in national and regional coalconsumption and emissions resulting from adjustments in railroad transportation rates for Wyoming's Powder River Basin (PRB) coal using the National Energy Modeling System(NEMS). However, because NEMS operates at a relatively aggregate regional level and does not represent the costs of transporting coal over specific rail lines, this analysis reports on the impacts of interregional changes in transportation rates from those used in the Annual Energy Outlook 2005 (AEO2005) reference case.

John Conti

2005-04-01T23:59:59.000Z

288

Billiards with polynomial mixing rates  

E-Print Network (OSTI)

While many dynamical systems of mechanical origin, in particular billiards, are strongly chaotic -- enjoy exponential mixing, the rates of mixing in many other models are slow (algebraic, or polynomial). The dynamics in the latter are intermittent between regular and chaotic, which makes them particularly interesting in physical studies. However, mathematical methods for the analysis of systems with slow mixing rates were developed just recently and are still difficult to apply to realistic models. Here we reduce those methods to a practical scheme that allows us to obtain a nearly optimal bound on mixing rates. We demonstrate how the method works by applying it to several classes of chaotic billiards with slow mixing as well as discuss a few examples where the method, in its present form, fails.

Nikolai Chernov; Hong-Kun Zhang

2004-09-12T23:59:59.000Z

289

Hardware implementation of wireless bit rate adaptation  

E-Print Network (OSTI)

This thesis presents a hardware implementation of the SoftRate bit-rate adaptation protocol. SoftRate is a new bit-rate adaptation protocol, which uses per-bit confidence hints generated by the convolutional decoder to ...

Gross, Samuel A

2010-01-01T23:59:59.000Z

290

The NoAH difference Generic architecture The NoAH Components Argos  

E-Print Network (OSTI)

Worms, viruses and trojans common occurrences in our daily interaction with computers Zero-day exploits used for installing various malware Selective attacks Traditional approaches too slow too inaccurate looking for known malware

Dr. Catalin Meirosu; Evangelos Markatos; Asia Slowinska; Klaus Moeller; Jan Kohlrausch; Spiros Antonatos

2005-01-01T23:59:59.000Z

291

The impact of ventilation rate on the emission rates of volatile...  

NLE Websites -- All DOE Office Websites (Extended Search)

impact of ventilation rate on the emission rates of volatile organic compounds in residences Title The impact of ventilation rate on the emission rates of volatile organic...

292

Property:OpenEI/UtilityRate/DemandRateStructure/Tier4Rate | Open Energy  

Open Energy Info (EERE)

Rate" Rate" Showing 13 pages using this property. 4 4b524791-bef2-49b1-850b-458730755203 + 5 +, 6 +, 3 +, ... 4b524791-bef2-49b1-850b-458730755203 + 6 + 4b524791-bef2-49b1-850b-458730755203 + 3 + 4b524791-bef2-49b1-850b-458730755203 + 7 + 4b524791-bef2-49b1-850b-458730755203 + 5 + 4b524791-bef2-49b1-850b-458730755203 + 8 + 4b524791-bef2-49b1-850b-458730755203 + 5 + 4b524791-bef2-49b1-850b-458730755203 + 5 + 4b524791-bef2-49b1-850b-458730755203 + 6 + 4b524791-bef2-49b1-850b-458730755203 + 6 + E E40880ac-c27b-4cbf-a011-b0d7d6e10fe9 + 1 + E40880ac-c27b-4cbf-a011-b0d7d6e10fe9 + 1 + E40880ac-c27b-4cbf-a011-b0d7d6e10fe9 + 1 + Retrieved from "http://en.openei.org/w/index.php?title=Property:OpenEI/UtilityRate/DemandRateStructure/Tier4Rate&oldid=53975

293

Energy Management Through Innovative Rates  

E-Print Network (OSTI)

Increased costs and a continuing dependence on uncertain supplies of domestic and foreign energy resources have prompted many companies to focus their attention on energy management. The author explores the potential for achieving a greater measure of energy efficiency in the industrial sector and specific rate design alternatives for doing so.

Williams, M. L.

1982-01-01T23:59:59.000Z

294

SIL rating fire protection equipment  

Science Conference Proceedings (OSTI)

SIL's (Safety Integrity Levels) are used by IEC 61508:1998 [1] to characterise the required functional safety of computer control systems. For example, SIL 4, the highest rating is for fly by wire aircraft and weapons systems and track circuited train ... Keywords: SIL, fire control panels, fire systems

Richard M. Robinson; Kevin J. Anderson

2003-10-01T23:59:59.000Z

295

Fast repetition rate (FRR) flasher  

DOE Patents (OSTI)

A fast repetition rate (FRR) flasher is described suitable for high flash photolysis including kinetic chemical and biological analysis. The flasher includes a power supply, a discharge capacitor operably connected to be charged by the power supply, and a flash lamp for producing a series of flashes in response to discharge of the discharge capacitor. A triggering circuit operably connected to the flash lamp initially ionizes the flash lamp. A current switch is operably connected between the flash lamp and the discharge capacitor. The current switch has at least one insulated gate bipolar transistor for switching current that is operable to initiate a controllable discharge of the discharge capacitor through the flash lamp. Control means connected to the current switch for controlling the rate of discharge of the discharge capacitor thereby to effectively keep the flash lamp in an ionized state between successive discharges of the discharge capacitor. Advantageously, the control means is operable to discharge the discharge capacitor at a rate greater than 10,000 Hz and even up to a rate greater than about 250,000 Hz. 14 figs.

Kolber, Z.; Falkowski, P.

1997-02-11T23:59:59.000Z

296

Electric Rate Alternatives to Cogeneration  

E-Print Network (OSTI)

This paper discusses electric rate alternatives to cogeneration for the industrial customer and attempts to identify the effects on the utility company, the industrial customer as well as remaining customers. It is written from the perspective of one company and its exposure to cogenerstion within its service territory.

Sandberg, K. R. Jr.

1988-09-01T23:59:59.000Z

297

Instability statistics and mixing rates  

E-Print Network (OSTI)

We claim that looking at probability distributions of \\emph{finite time} largest Lyapunov exponents, and more precisely studying their large deviation properties, yields an extremely powerful technique to get quantitative estimates of polynomial decay rates of time correlations and Poincar\\'e recurrences in the -quite delicate- case of dynamical systems with weak chaotic properties.

Roberto Artuso; Cesar Manchein

2009-06-03T23:59:59.000Z

298

2010FirmRateAdj  

NLE Websites -- All DOE Office Websites (Extended Search)

Firm Peaking Revenue Requirement 320.2 million P-SMPB--ED Composite Rate 33.25 millskWh Firm Demand 7.65kWmo Firm Energy 19.05 millskWh Firm Peaking Demand 6.90kWmo Firm...

299

Building Energy Performance Certificate. Asset Rating.  

U.S. Energy Information Administration (EIA)

Non-Domestic Building Energy Performance Asset Rating ... Asset Rating. Author: BRE Subject: LCEA029636 Keywords: Energy Performance Certificate ...

300

Energy Efficiency Interest Rate Reduction Program | Department...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Interest Rate Reduction Program Energy Efficiency Interest Rate Reduction Program Eligibility Residential Savings For Heating & Cooling Home Weatherization Construction Commercial...

Note: This page contains sample records for the topic "ah rated pack" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


301

An investigation of the effect of pore scale flow on average geochemical reaction rates using direct numerical simulation  

Science Conference Proceedings (OSTI)

The scale-dependence of geochemical reaction rates hinders their use in continuum scale models intended for the interpretation and prediction of chemical fate and transport in subsurface environments such as those considered for geologic sequestration of CO{sub 2}. Processes that take place at the pore scale, especially those involving mass transport limitations to reactive surfaces, may contribute to the discrepancy commonly observed between laboratory-determined and continuum-scale or field rates. Here, the dependence of mineral dissolution rates on the pore structure of the porous media is investigated by means of pore scale modeling of flow and multicomponent reactive transport. The pore scale model is comprised of high performance simulation tools and algorithms for incompressible flow and conservative transport combined with a general-purpose multicomponent geochemical reaction code. The model performs direct numerical simulation of reactive transport based on an operator-splitting approach to coupling transport and reactions. The approach is validated with a Poiseuille flow single-pore experiment and verified with an equivalent 1D continuum-scale model of a capillary tube packed with calcite spheres. Using the case of calcite dissolution as an example, the high resolution model is used to demonstrate that non-uniformity in the flow field at the pore scale has the effect of decreasing the overall reactivity of the system, even when systems with identical reactive surface area are considered. The effect becomes more pronounced as the heterogeneity of the reactive grain packing increases, particularly where the flow slows sufficiently such that the solution approaches equilibrium locally and the average rate becomes transport-limited.

Rafa, S. Molins; Trebotich, D.; Steefel, C. I.; Shen, C.

2012-02-01T23:59:59.000Z

302

Federal Energy Management Program: Water Rate Escalations  

NLE Websites -- All DOE Office Websites (Extended Search)

Rate Rate Escalations to someone by E-mail Share Federal Energy Management Program: Water Rate Escalations on Facebook Tweet about Federal Energy Management Program: Water Rate Escalations on Twitter Bookmark Federal Energy Management Program: Water Rate Escalations on Google Bookmark Federal Energy Management Program: Water Rate Escalations on Delicious Rank Federal Energy Management Program: Water Rate Escalations on Digg Find More places to share Federal Energy Management Program: Water Rate Escalations on AddThis.com... Sustainable Buildings & Campuses Operations & Maintenance Greenhouse Gases Water Efficiency Basics Federal Requirements Best Management Practices Analysis and Evaluation Water Rate Escalations Evaluation Service Contracts Case Studies Resources

303

Electric vehicle propulsion batteries: design and cost study for nickel/zinc battery manufacture. Task A. [25 kWh, 700 pounds, 245 Ah at 100+ V, 4. 77 ft/sup 3/  

DOE Green Energy (OSTI)

For satisfying the 25-kWh energy requirement necessary for vehicle propulsion, a 700-pound nickel--zinc battery was configured. Containing 64 individual cells, the unit was selected for minimum weight from computed packaging possibilities. Unit volume was projected to be 4.77 cubic feet. Capacity of the cells delivering 100+ volts was set at 245 ampere-hours. Selection was made primarily because of the compatibility with expressed vehicle requirements of a lower-current system. Manufacturing costs were computed for a unit using sintered positive electrodes at $86/kWh, pilot plant rate, and $78/kWh, production plant rate. Based on a lower than anticipated cost differential between sintered and nonsintered positive electrodes and certain other performance differences, the sintered electrode was chosen for the battery design. Capital expenditures for a production rate of 10,000 batteries per year are estimated to be $2,316,500. Capital expenditure for demonstrating production rates in a pilot plant facility is approximately $280,000, with the use of some shared available equipment. 29 figures, 9 tables.

None

1977-01-01T23:59:59.000Z

304

P-D Project Rate Adjustment  

NLE Websites -- All DOE Office Websites (Extended Search)

Parker-Davis Project Rate Adjustment Data Parker-Davis Project Rate Adjustment Data FY2014 Informal Customer Meeting Notification of Meeting Presentation Preliminary CAS Preliminary Rate Design Preliminary PRS Final Documents Notification of Rates Final CAS Final Rate Design Final PRS FY2013 Informal Customer Meeting Notification of Meeting Presentation Preliminary CAS Preliminary Rate Design Preliminary PRS Supplemental Information Final Documents Notification of Rates Final CAS Final Rate Design Final PRS FY2012 Informal Customer Meeting Notification of Meeting Presentation Preliminary CAS Preliminary Rate Design Preliminary PRS Customer Requested Scenario Final Documents Notification of Rates Final CAS Final Rate Design Final PRS FY2011 Informal Customer Meeting Notification of Meeting Presentation Preliminary CAS Preliminary Rate Design

305

Further Study on Atmospheric Lapse Rate Regimes  

Science Conference Proceedings (OSTI)

Lapse rate, moist adiabatic lapse rate and the critical lapse rate for baroclinic adjustment are calculated as was done by Stone and Carlson using a different data set covering both hemispheres. Results show very good agreement in low latitudes, ...

Shi-Keng Yang; G. Louis Smith

1985-05-01T23:59:59.000Z

306

Narrowing the estimates of species migration rates  

E-Print Network (OSTI)

of species migration rates How fast can species migrate?estimate population growth rates for each population sinceon their data 1 show that the rate of population spread is

Blois, Jessica L.

2013-01-01T23:59:59.000Z

307

4. Trends in Natural Gas Transportation Rates  

U.S. Energy Information Administration (EIA)

Energy Information Administration 39 Energy Policy Act Transportation Study: Interim Report on Natural Gas Flows and Rates 4. Trends in Natural Gas Transportation Rates

308

Definition: Thermal Rating | Open Energy Information  

Open Energy Info (EERE)

Rating Jump to: navigation, search Dictionary.png Thermal Rating The maximum amount of electrical current that a transmission line or electrical facility can conduct over a...

309

Form:Utility Rate | Open Energy Information  

Open Energy Info (EERE)

Form Edit History Facebook icon Twitter icon Form:Utility Rate Jump to: navigation, search Add or Update Utility Rate Information Retrieved from "http:en.openei.orgw...

310

CRSP Transmission Sales Rate History  

NLE Websites -- All DOE Office Websites (Extended Search)

Updated: 12/20/2013 Updated: 12/20/2013 CRSP Transmission Sales Rate History Rate Schedule Effective Dates Nonfirm (Mills/kWh) Firm ($/kW-yr.) Firm ($/kW-mo.) None Through 3/83 1.000 $ 6.60 $0.55 SP-FT1 4/83 - 6/86 N.A. $10.27 $0.86 SP-NFT1 4/83 - 6/86 2.000 N.A. SP-FT2 7/86 - 6/89 N.A. $15.94 $1.33 SP-NFT2 7/86 - 7/89 3.100 N.A. SP-FT3 7/89 - 9/92 N.A. $21.72 $1.81 SP-NFT3 8/89 - 3/98 Mutually Agreed N.A. SP-FT4 10/92 - 3/98 N.A. $22.68 $1.89 SP-NFT4 4/98 - 3/03 Mutually Agreed N.A. SP-PTP5 4/98 - 3/99 N.A. $26.70 $2.23 4/99 - 3/00 N.A. $26.19 $2.18 4/00 - 3/01 N.A. $26.14 $2.18 4/01 - 3/02 N.A. $25.63 $2.14 4/02 - 9/02 N.A. $21.33 $1.78 SP-NFT5 10/02 - 9/07 Mutually Agreed N.A. 10/07-9/08 Mutually Agreed N.A. SP-PTP6 10/02 - 9/03 N.A. $24.72 $2.06

311

Accurate quantum thermal rate constants for the three-dimensional H+H/sub 2/ reaction  

SciTech Connect

The rate constants for the three-dimensional H+H/sub 2/ reaction on the Liu--Siegbahn--Truhlar--Horowitz (LSTH) surface are calculated using Pack--Parker hyperspherical (APH) coordinates and a /ital C//sub 2/ital v// symmetry adapted direct product discrete variable representation (DVR). The /ital C//sub 2/ital v// symmetry decomposition and the parity decoupling on the basis are performed for the internal coordinate xi. The symmetry decomposition results in a block diagonal representation of the flux and Hamiltonian operators. The multisurface flux is introduced to represent the multichannel reactive flux. The eigenvalues and eigenvectors of the /ital J/=0 internal Hamiltonian are obtained by sequential diagonalization and truncation. The individual symmetry blocks of the flux operator are propagated by the corresponding blocks of the Hamiltonian, and the /ital J/=0 rate constant /ital k//sup 0/(/ital T/) is obtained as a sum of the rate constants calculated for each block. /ital k//sup 0/(/ital T/) is compared with the exact /ital k//sup 0/(/ital T/) obtained from thermal averaging of the /ital J/=0 reaction probabilities; the errors are within 5%--20% up to /ital T/=1500 K. The sequential diagonalization--truncation method reduces the size of the Hamiltonian greatly, but the resulting Hamiltonian matrix still describes the time evolution very accurately. For the /ital J//ne/0 rate constant calculations, the truncated internal Hamiltonian eigenvector basis is used to construct reduced (/ital JK//sub /ital J//) blocks of the Hamiltonian. The individual (/ital JK//sub /ital J//) blocks are diagonalized neglecting Coriolis coupling and treating the off-diagonal /ital K//sub /ital J//+-2 couplings by second order perturbation theory. The full wave function is parity decoupled. The rate constant is obtained as a sum over /ital J/ of (2/ital J/+1)/ital k//sup /ital J//(/ital T/).

Park, T. J.; Light, J. C.

1989-07-15T23:59:59.000Z

312

utility rate | OpenEI Community  

Open Energy Info (EERE)

utility rate utility rate Home Sfomail's picture Submitted by Sfomail(48) Member 17 May, 2013 - 11:14 Utility Rates API Version 2 is Live! API developer OpenEI update utility Utility Companies utility rate Utility Rates version 1 version 2 version 3 web service Smart meter After several months of development and testing, the next generation web service for the utility rate database is finally here! I encourage you to check out the V2 Utility Rates API at http://en.openei.org/services/doc/rest/util_rates Rmckeel's picture Submitted by Rmckeel(297) Contributor 22 June, 2012 - 09:30 Increasing ask query limit developer utility rate An NREL user who is trying to use the utility rate service was having an issue. He writes "I noticed that any rates past 10,000 are not accessible via json. For example, this query only returns two entries:

313

Wholesale Power Rate Schedules | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Services » Rate Schedules » Wholesale Power Rate Schedules Services » Rate Schedules » Wholesale Power Rate Schedules Wholesale Power Rate Schedules October 1, 2012 ALA-1-N Wholesale Power Rate Schedule Area: PowerSouth Energy Cooperative System: Georgia-Alabama-South Carolina October 1, 2012 Duke-1-E Wholesale Power Rate Schedule Area: Duke On-System System: Georgia-Alabama-South Carolina October 1, 2012 Duke-2-E Wholesale Power Rate Schedule Area: Central System: Georgia-Alabama-South Carolina October 1, 2012 Duke-3-E Wholesale Power Rate Schedule Area: None System: Georgia-Alabama-South Carolina October 1, 2012 Duke-4-E Wholesale Power Rate Schedule Area: Duke Self-Schedulers System: Georgia-Alabama-South Carolina October 1, 2012 MISS-1-N Wholesale Power Rate Schedule Area: South Mississippi Electric Power Association

314

Wholesale Power Rate Schedules | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Services » Rate Schedules » Wholesale Power Rate Schedules Services » Rate Schedules » Wholesale Power Rate Schedules Wholesale Power Rate Schedules October 1, 2012 ALA-1-N Wholesale Power Rate Schedule Area: PowerSouth Energy Cooperative System: Georgia-Alabama-South Carolina October 1, 2012 Duke-1-E Wholesale Power Rate Schedule Area: Duke On-System System: Georgia-Alabama-South Carolina October 1, 2012 Duke-2-E Wholesale Power Rate Schedule Area: Central System: Georgia-Alabama-South Carolina October 1, 2012 Duke-3-E Wholesale Power Rate Schedule Area: None System: Georgia-Alabama-South Carolina October 1, 2012 Duke-4-E Wholesale Power Rate Schedule Area: Duke Self-Schedulers System: Georgia-Alabama-South Carolina October 1, 2012 MISS-1-N Wholesale Power Rate Schedule Area: South Mississippi Electric Power Association

315

Packed-Bed Reactor Study of NETL Sample 196c for the Removal of Carbon Dioxide from Simulated Flue Gas Mixture  

Science Conference Proceedings (OSTI)

An amine-based solid sorbent process to remove CO2 from flue gas has been investigated. The sorbent consists of polyethylenimine (PEI) immobilized onto silica (SiO2) support. Experiments were conducted in a packed-bed reactor and exit gas composition was monitored using mass spectrometry. The effects of feed gas composition (CO2 and H2O), temperature, and simulated steam regeneration were examined for both the silica support as well as the PEI-based sorbent. The artifact of the empty reactor was also quantified. Sorbent CO2 capacity loading was compared to thermogravimetric (TGA) results to further characterize adsorption isotherms and better define CO2 working capacity. Sorbent stability was monitored by periodically repeating baseline conditions throughout the parametric testing and replacing with fresh sorbent as needed. The concept of the Basic Immobilized Amine Sorbent (BIAS) Process using this sorbent within a system where sorbent continuously flows between the absorber and regenerator was introduced. The basic tenet is to manipulate or control the level of moisture on the sorbent as it travels around the sorbent circulation path between absorption and regeneration stages to minimize its effect on regeneration heat duty.

Hoffman, James S.; Hammache, Sonia; Gray, McMahan L.; Fauth Daniel J.; Pennline, Henry W.

2012-04-24T23:59:59.000Z

316

In-depth survey report of silica flour dust during packing, transfer, and shipping at the Central Silica Company, Glass Rock Plant, Glass Rock, Ohio  

Science Conference Proceedings (OSTI)

A visit was made to the Central Silica Company, Glass Rock, Ohio to evaluate methods used to control employee exposure to silica dust. The control methods at this company included careful handling and transfer of damp materials, exhaust ventilation, good housekeeping procedures, and the use of respiratory protection. Evaluations were made of the packing area, transfer point, inside loading trucks, and ambient air at sections of the flour building. Control systems included a good exhaust-ventilation system and four ventilation hoods. Evaluations were made of samples collected by an MSA gravimeter dust sampler, the Del High volume electrostatic precipitation, and bulk and rafter samples. Dust control methods appeared to be effective due to the existence of good engineering controls, good work practices, and an effective respiratory protection program. Additional control measures included the handling of the ore as a damp material, thus reducing the generation of dust particles. Outside dust sources were being reduced. Most of the product was shipped in bulk. Plastic wrapping was used around pallet loads to reduce bag breakage and dust dispersion. A filtered air system controlled low dust levels in the Pebble Mill control room. Enclosed screens operated under negative pressure separated fine from coarse product at the process building.

Caplan, P.E.; Reed, L.D.; Amendola, A.A.; Cooper, T.C.

1981-12-01T23:59:59.000Z

317

Property:OpenEI/UtilityRate/EnergyRateStructure/Tier5Rate | Open Energy  

Open Energy Info (EERE)

Rate" Rate" Showing 25 pages using this property. (previous 25) (next 25) 0 00c88d6d-e3b0-4128-ad3e-a93f686cf6e3 + 0.227 + 00c88d6d-e3b0-4128-ad3e-a93f686cf6e3 + 0.227 + 00c88d6d-e3b0-4128-ad3e-a93f686cf6e3 + 0.227 + 019be14c-4635-4529-af90-799cbf5d7865 + 0.0335 + 019be14c-4635-4529-af90-799cbf5d7865 + 0.0335 + 02b061e1-f065-421e-9ebc-76aef4734486 + 0.079 + 02b061e1-f065-421e-9ebc-76aef4734486 + 0.079 + 02fc76fd-35ff-44c3-bc85-1fb1918f125b + 0.0978 + 02fc76fd-35ff-44c3-bc85-1fb1918f125b + 0.0978 + 0402cc99-ab16-40cc-83e7-2c5910a825a1 + 0.061 + 0402cc99-ab16-40cc-83e7-2c5910a825a1 + 0.061 + 041466a9-81ca-4fce-90e3-e718159347a9 + 0.0587 +, 0.044 + 041466a9-81ca-4fce-90e3-e718159347a9 + 0.044 + 041466a9-81ca-4fce-90e3-e718159347a9 + 0.0587 + 047086c9-976d-4a05-90d5-b67afaf60851 + 0.0583 +

318

Distributed Rate Allocation for Wireless Networks  

E-Print Network (OSTI)

This paper describes a distributed algorithm for rate allocation in wireless networks. As the main result, the paper establishes that this algorithm is throughput-optimal for very general class of throughput regions. In contrast to distributed on-off scheduling algorithms, this algorithm enables optimal utilization of physical layer schemes by scheduling multiple rate levels. The algorithm is based on a Markov process on these discrete set of rates with certain transition rates. For dealing with multiple rate levels, the paper introduces an important structure for the transition rates, which enable the design of appropriate update rule for these transition rates. The update uses local queue length information alone, and thus does not require global exchange of queue length information. In addition, the algorithm requires that each link can determine the feasibility of increasing its data-rate from the current value without reducing the data-rates of other links. Determining rate feasibility does not introduce...

Jose, Jubin

2010-01-01T23:59:59.000Z

319

The purpose of this pack This pack presents the Forestry  

E-Print Network (OSTI)

pellets. (b) Commercial scale wood chip fuelled boiler. (c) Combined heat and power gasifier unit pellet production as fuel for domestic appliances and as a replacement for fossil fuel in some larger suitable for wood pellets. Wood chips and hog fuel: an example High quality wood chips recommended

320

Computerized extrapolation of hydrolysis rate data  

Science Conference Proceedings (OSTI)

The program RATE was developed to aid in the extrapolation and interpretation of hydrolysis rate data to a format that is useful for environmental risk assessment. Hydrolysis data typically are reported in the literature as pseudo-first-order rate constants at the temperature and pH of the reaction medium used to obtain the kinetics information. The utility of RATE lies in its ability to estimate first-order rate constants at other values of temperature and pH and to convert pseudo-first-order rate constants to second-order rate constants. RATE also will calculate the half-life for the overall reaction, including neutral-, base-, and acid-mediated hydrolysis, at any selected temperature and pH. RATE, programmed in FORTRAN, is used to systematically analyze data for entry in FATE, a comprehensive environmental fate constants information system database.

Hamrick, K.J.; Kollig, H.P.; Bartell, B.A.

1992-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "ah rated pack" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


321

Wholesale Power Rate Schedules | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Schedules Schedules Wholesale Power Rate Schedules October 1, 2011 CBR-1-H Wholesale Power Rate Schedule Area: Big Rivers and Henderson, KY System: CU October 1, 2011 CSI-1-H Wholesale Power Rate Schedule Area: Southern Illinois System: CU October 1, 2011 CK-1-H Wholesale Power Rate Schedule Area: KU Area System: CU October 1, 2011 CEK-1-H Wholesale Power Rate Schedule Area: East Kentucky System: CU October 1, 2011 CC-1-I Wholesale Power Rate Schedule Area: CP&L Area, Western Division System: CU September 20, 2011 JW-1-J Wholesale Power Rate Schedule Area: Woodruff Preference Customer System: Jim Woodruff September 20, 2011 JW-2-F Wholesale Power Rate Schedule Area: Florida Power Corporation System: Jim Woodruff November 17, 2010 AP-1-B Wholesale Power Rate Schedule Area: American Electric Power

322

1996 Wholesale Power and Transmission Rate Schedules.  

Science Conference Proceedings (OSTI)

Bonneville Power Administration`s (BPA) 1996 Wholesale Power Rate Schedules, 1996 Ancillary Products and Services Rate Schedule, 1996 Transmission Rate Schedules, and General Rate Schedule Provisions, contained herein, were approved on an interim basis effective October 1, 1996. These rate schedules and provisions were approved by the Federal Energy Regulatory Commission (FERC), United States Department of Energy, in September 1996 (Docket Nos EF96-2011-000 and EF96f-2021-000). These rate schedules and General Rate Schedule Provisions were approved on a final basis by the FERC July 30, 1997, in Dept. of Energy--Bonneville Power Administration, Docket Nos. EF96-2011-000 and EF96-2021-000. Except as noted elsewhere, these 1996 rate schedules and provisions supersede BPA`s Wholesale Power Rate Schedules and General Rate Schedule Provisions, and Transmission Rate Schedules and General Transmission Rate Schedule Provisions, effective October 1, 1995. These rate schedules and general rate schedule provisions include all errata.

United States. Bonneville Power Administration.

1996-10-01T23:59:59.000Z

323

Utility Rate | OpenEI Community  

Open Energy Info (EERE)

Utility Rate Utility Rate Home > Utility Rate > Posts by term > Utility Rate Content Group Activity By term Q & A Feeds Term: API Type Term Title Author Replies Last Post sort icon Blog entry API The utility rate database version 1 API is now deprecated Rmckeel 6 Sep 2013 - 14:00 Blog entry API Lighting Electricity Rates on OpenEI Sfomail 31 May 2013 - 12:04 Blog entry API Utility Rates API Version 2 is Live! Sfomail 17 May 2013 - 11:14 Groups Menu You must login in order to post into this group. Recent content There is currently no way to s... ranking of utilities by demand charge? FYI, OpenEI now accommodates t... Very useful information. Thank... The utility rate database version 1 API is now deprecated more Group members (28) Managers: Dloomis

324

Cross-layer wireless bit rate adaptation  

E-Print Network (OSTI)

This paper presents SoftRate, a wireless bit rate adaptation protocol that is responsive to rapidly varying channel conditions. Unlike previous work that uses either frame receptions or signal-to-noise ratio (SNR) estimates ...

Vutukuru, Mythili

2009-01-01T23:59:59.000Z

325

Cross-Layer Wireless Bit Rate Adaptation  

E-Print Network (OSTI)

This paper presents SoftRate, a wireless bit rate adaptation protocol that is responsive to rapidly varying channel conditions. Unlike previous work that uses either frame receptions or signal-to-noise ratio (SNR) estimates ...

Vutukuru, Mythili

326

Transfer Rate vs. I/O Units  

NLE Websites -- All DOE Office Websites (Extended Search)

O Units Transfer Rate vs. IO Units These plots show the transfer rate from the IO benchmarks as a function of the number of elizaio units in use for each particular eliza at the...

327

OpenEI Community - utility rate  

Open Energy Info (EERE)

Rates API Rates API Version 2 is Live! http://en.openei.org/community/blog/utility-rates-api-version-2-live Smart meterAfter several months of development and testing, the next generation web service for the utility rate database is finally here! I encourage you to check out the V2 Utility Rates API at rates">http://en.openei.org/services/doc/rest/util_ratesrates-api-version-2-live" target="_blank">read more

328

Cumulus Parameterization and Rainfall Rates I  

Science Conference Proceedings (OSTI)

Modeling of convective rainfall rates is a central problem in tropical meteorology. Toward numerical weather prediction efforts the semi-prognostic approach (i.e., a one time-step prediction of rainfall rates) provides a relevant test of cumulus ...

T. N. Krishnamurti; Y. Ramanathan; Hua-Lu Pan; Richard J. Pasch; John Molinari

1980-04-01T23:59:59.000Z

329

Why Oceanic Dissipation Rates Are Not Lognormal  

Science Conference Proceedings (OSTI)

In their derivation of the lognormal probability density function for volume-averaged dissipation rates, Gurvich and Yaglom assumed explicitly that these dissipation rates are statistically homogeneous and that the averaging scale is small ...

Hidekatsu Yamazaki; Rolf Lueck

1990-12-01T23:59:59.000Z

330

A Probability Distribution Model for Rain Rate  

Science Conference Proceedings (OSTI)

A systematic approach is suggested for modeling the probability distribution of rain rate. Rain rate, conditional on rain and averaged over a region, is modeled as a temporally homogeneous diffusion process with appropriate boundary conditions. ...

Benjamin Kedem; Harry Pavlopoulos; Xiaodong Guan; David A. Short

1994-12-01T23:59:59.000Z

331

Rain Rate Estimates from Differential Polarization Measurements  

Science Conference Proceedings (OSTI)

This paper presents an analysis of the accuracy of rain rate estimates from data observed with a radar that has alternating horizontal and vertical polarization. Theoretical accuracies of rain rates from the reflectivity, the differential ...

M. Sachidananda; D. S. Zrni?

1987-12-01T23:59:59.000Z

332

On-site Housing Rates | Staff Services  

NLE Websites -- All DOE Office Websites (Extended Search)

Rates Effective February 1, 2013 Rates for Occupancy < 30-Days Guest House* SingleDouble: 105.00 per day Housekeeping service is provided on all working days. *Alternatives to...

333

CONVERGENCE AND CONVERGENCE RATE OF STOCHASTIC ...  

E-Print Network (OSTI)

gence rate of { ?f(?n)2}n?0 and {f(?n)}n?0 is the slower of the rates O(??r? n. ) (the ...... for ??,s nj ? knj+1. Then...

334

Geomagnetic Reversals: Rates, Timescales, Preferred Paths,  

E-Print Network (OSTI)

Geomagnetic Reversals: Rates, Timescales, Preferred Paths, Statistical Models and Simulations: Geomagnetic reversals, Reversal rates, Paleointensity, Statistics of Geodynamo September 30, 2001 #12;Abstract Paleomagnetic data on geomagnetic reversals are divided into two general categories: times of occurrence

Constable, Catherine G.

335

Rio Grande Project Power Sales Rate History  

NLE Websites -- All DOE Office Websites (Extended Search)

Power Sales Rate History Updated: 1022009 Rate Schedule Effective Dates Energy (MillskWh) Capacity (kW-mo.) Combined (MillskWh) R5-F1 1940 - 1949 3.000 - 8.000 (declining...

336

Collbran Project Power Sales Rate History  

NLE Websites -- All DOE Office Websites (Extended Search)

Power Sales Rate History Updated: 1022009 Rate Schedule Effective Dates Energy (MillskWh) Capacity (kW-mo.) Combined (MillskWh) Contract 1262 - 1283 (Firm Only) (Nonfirm...

337

Science & Technology Principal Directo rate Industrial ...  

Erik Stenehjem Science & Technology Principal Directo rate Industrial Partnerships Office Erik Stenehjem Director----Roger Werne Deputy Director

338

Reproduction Rates for 19902002 and Intrinsic Rates for 20002001: United States  

E-Print Network (OSTI)

ObjectiveThis report presents revised rates of reproduction for 199093, reproduction rates for 19942002, and intrinsic rates for 20002001. The revised rates for 199193 are based on populations consistent with the April 1, 2000, census, as are the rates for 19942002. MethodsTabular and graphic data on the reproduction and intrinsic rates by race and Hispanic origin of mother are presented and described. ResultsRates of reproduction (total fertility, gross reproduction, and net reproduction rates), the intrinsic rate of natural increase, and the intrinsic birth rate were lower in 2001 (and 2002) than 1990. Among the race and Hispanic subgroups, the reproduction rates were lower for all groups except Cubans and whites (total). The overall intrinsic death rate increased between 1990 and 2001 with the rate declining for whites (total) but increasing for blacks (total).

Brady E. Hamilton, Ph.D.; Division Of Vital Statistics

2004-01-01T23:59:59.000Z

339

EPRI's Twelfth Heat Rate Improvement Conference Proceedings  

Science Conference Proceedings (OSTI)

The Twelfth Heat Rate Improvement Conference, sponsored by EPRI's Heat Rate and Cost Optimization Value Package, is the latest in a series of meetings designed to assist utilities in addressing problems with power plant performance and in identifying cost-effective solutions for achieving and maintaining heat rate improvement. The last conference was held in Baltimore in September 1998.

2001-01-22T23:59:59.000Z

340

Definition: Emergency Rating | Open Energy Information  

Open Energy Info (EERE)

Emergency Rating Emergency Rating Jump to: navigation, search Dictionary.png Emergency Rating The rating as defined by the equipment owner that specifies the level of electrical loading or output, usually expressed in megawatts (MW) or Mvar or other appropriate units, that a system, facility, or element can support, produce, or withstand for a finite period. The rating assumes acceptable loss of equipment life or other physical or safety limitations for the equipment involved.[1] Related Terms rating References ↑ Glossary of Terms Used in Reliability Standards An LikeLike UnlikeLike You like this.Sign Up to see what your friends like. inline Glossary Definition Retrieved from "http://en.openei.org/w/index.php?title=Definition:Emergency_Rating&oldid=480317" Categories:

Note: This page contains sample records for the topic "ah rated pack" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


341

Water Rate Escalations | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Rate Escalations Rate Escalations Water Rate Escalations October 8, 2013 - 9:55am Addthis Federal agencies need accurate water cost escalation rates to perform life cycle cost analyses for water efficiency projects to meet Executive Order 13514 and Energy Independence and Security Act of 2007 requirements. To estimate long-term escalation rates of potable water, Pacific Northwest National Laboratory (PNNL) conducted an analysis. Using the trends from this study, Federal facility managers can select escalation rates from studied cities with similar circumstances to their facility locations such as U.S. region, water source, or drought tendencies. Also they can make more informed choices on possible water escalation rates that can be used in economic analysis of water efficiency projects.

342

Utility Rates | OpenEI Community  

Open Energy Info (EERE)

Utility Rates Utility Rates Home Rmckeel's picture Submitted by Rmckeel(297) Contributor 6 September, 2013 - 14:00 The utility rate database version 1 API is now deprecated API Utility Rates There comes a time in every API version's lifecycle when it needs to be deprecated. OpenEI's utility rate database version 1 API has been in use since the inception of the database in 2010. As Illinois State University has taken a commanding lead of the project and its data curation, we have updated the schema and API to version 2 to present a richer spectrum of utility rate data. Rmckeel's picture Submitted by Rmckeel(297) Contributor 11 June, 2013 - 09:33 Tip for working with approvals on OpenEI EZFeed Utility Rates The "ApprovedRevs" extension is the feature on OpenEI that allows

343

Investigation and modeling of processing-microstructure-property relations in ultra-fine grained hexagonal close packed materials under strain path changes  

E-Print Network (OSTI)

Ultra-fine grained (UFG) materials have attracted considerable interest due to the possibility of achieving simultaneous increase in strength and ductility. Effective use of these materials in engineering applications requires investigating the processing-microstructure-property inter-relations leading to a comprehensive understanding of the material behavior. Research efforts on producing UFG hexagonal close packed (hcp) materials have been limited in spite of their envisaged utilization in various technologies. The present study explores multiple UFG hcp materials to identify the general trends in their deformation behaviors, microstructural features, crystallographic texture evolutions and mechanical responses under strain path changes. UFG hcp materials, including commercial purity Ti, Ti-6Al-4V alloy and high purity Zr, were fabricated using equal channel angular extrusion (ECAE) as a severe plastic deformation (SPD) technique following various processing schedules. Several characterization methods and a polycrystal plasticity model were utilized in synergy to impart the relationships between the UFG microstructure, the texture and the post-ECAE flow behavior. Pure UFG hcp materials exhibited enhanced strength properties, making them potential substitutes for coarse-grained high strength expensive alloys. Incorporation of post-ECAE thermo-mechanical treatments was effective in further improvement of the strength and ductility levels. Strong anisotropy of the post-ECAE flow response was evident in all the materials studied. The underlying mechanisms for anisotropy were identified as texture and processing-induced microstructure. Depending on the ECAE route, the applied strain level and the specific material, the relative importance of these two mechanisms on plastic flow anisotropy varied. A viscoplastic self-consistent approach is presented as a reliable model for predicting the texture evolutions and flow behaviors of UFG hcp materials in cases where texture governs the plastic anisotropy. Regardless of the material, the initial billet texture and the extrusion conditions, ECAE of all hcp materials revealed similar texture evolutions. Accurate texture and flow behavior predictions showed that basal slip is the responsible mechanism for such texture evolution in all hcp materials independent of their axial ratio. High strength of the UFG microstructure was presented as a triggering mechanism for the activation of unexpected deformation systems, such as high temperature deformation twinning in Ti-6Al-4V and room temperature basal slip in pure Zr.

Yapici, Guney Guven

2007-08-01T23:59:59.000Z

344

Definition: Penetration Rate | Open Energy Information  

Open Energy Info (EERE)

Definition Definition Edit with form History Facebook icon Twitter icon » Definition: Penetration Rate Jump to: navigation, search Dictionary.png Penetration Rate The Rate of penetration, abbreviated as ROP as used in the drilling industry, is the speed at which a drill bit breaks the rock under it to deepen the borehole. It is normally measured in feet per minute or meters per hour, but sometimes it is expressed in minutes per foot.[1] View on Wikipedia Wikipedia Definition The Rate of penetration, abbreviated as ROP as used in the drilling industry, is the speed at which a drill bit breaks the rock under it to deepen the borehole. Also known as penetration rate or drill rate. It is normally measured in feet per minute or meters per hour, but sometimes it is expressed in minutes per foot.

345

Utility Rate | OpenEI Community  

Open Energy Info (EERE)

Utility Rate Utility Rate Home > Utility Rate > Posts by term > Utility Rate Content Group Activity By term Q & A Feeds Term: developer Type Term Title Author Replies Last Post sort icon Blog entry developer Utility Rates API Version 2 is Live! Sfomail 17 May 2013 - 11:14 Discussion developer Utility rate change propagation is now much faster Rmckeel 1 21 Mar 2013 - 09:11 Blog entry developer OpenEI maintenance March 8-9, 2013 Rmckeel 8 Mar 2013 - 14:23 Blog entry developer Semantic Mediawiki Semantic Forms update Rmckeel 22 Oct 2012 - 07:23 Discussion developer Increasing ask query limit Rmckeel 1 28 Jun 2012 - 14:35 Groups Menu You must login in order to post into this group. Recent content FYI, OpenEI now accommodates t... Very useful information. Thank...

346

Rate-Making Policy | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Rate-Making Policy Rate-Making Policy Rate-Making Policy < Back Eligibility Investor-Owned Utility Rural Electric Cooperative Utility Savings Category Alternative Fuel Vehicles Hydrogen & Fuel Cells Buying & Making Electricity Water Home Weatherization Solar Wind Program Info Start Date 2005 State Wisconsin Program Type Generating Facility Rate-Making Provider Public Service Commission of Wisconsin WI Act 7 states that, when proposing the purchase or construction of an electric generating facility, a utility may "apply to the [WI Public Service Commission] for an order specifying in advance the rate-making principles" that the Public Service Commission will use for "future rate-making proceedings." The Nuclear Energy Institute highlights that "There is no restriction on

347

On loading rate effects in toughening processes  

SciTech Connect

Environmental crack tip reactions are a known source of premature fracture in oxides. These rate-dependent phenomena commonly are studied in strength tests where loading rate serves as the major experimental variable. A material susceptible to environmentally-assisted crack growth is stronger at fast testing rates. A topic which has received far less attention is the influence of stressing rate or loading rate on the shielding processes which occur at some distance from the crack tip, although the inverse has been studied by Deuerler et al. The authors present here the first known documentation of a loading rate effect on shielding phenomena in ceramic materials. For these experiments Coors AD 94 alumina was chosen for study.

Tandon, S.; Faber, K.T. [Northwestern Univ., Evanston, IL (United States)

1996-03-01T23:59:59.000Z

348

Definition: Dynamic Capability Rating | Open Energy Information  

Open Energy Info (EERE)

Capability Rating Capability Rating Jump to: navigation, search Dictionary.png Dynamic Capability Rating Dynamic capability rating can be achieved through real-time determination of an element's (e.g., line, transformer etc.) ability to carry load based on electrical and environmental conditions.[1] Related Terms rating References ↑ SmartGrid.gov 'Description of Functions' An LikeLike UnlikeLike You like this.Sign Up to see what your friends like. inline Glossary Definition Retrieved from "http://en.openei.org/w/index.php?title=Definition:Dynamic_Capability_Rating&oldid=506158" Categories: Definitions ISGAN Definitions What links here Related changes Special pages Printable version Permanent link Browse properties 429 Throttled (bot load) Error 429 Throttled (bot load) Throttled (bot load)

349

Building energy benchmarks and rating tools | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Building energy benchmarks and rating tools Building energy benchmarks and rating tools Building energy benchmarks and rating tools Building energy benchmarks and rating tools More...

350

Loads, capacity, and failure rate modeling  

SciTech Connect

Both failure rate and load capacity (stress-strength) interferenece methodologies are employed in the reliability analysis at nuclear facilities. Both of the above have been utilized in a heuristic failure rate model in terms of load capacity inference. Analytical solutions are used to demonstrate that infant mortality and random aging failures may be expressed implicity in terms of capacity variability, load variability, and capacity deterioration, and that mode interactions play a role in the formation of the bathtub curve for failure rates.

Lewis, E.E.; Chen, Hsin-Chieh

1994-12-31T23:59:59.000Z

351

FERC rate incentives for transmission infrastructure development  

Science Conference Proceedings (OSTI)

With enactment of the Energy Policy Act of 2005, Congress delivered a mandate to the Federal Energy Regulatory Commission to establish regulations that would provide for incentive-based rate treatments for investments that would improvement the nation's electric transmission system. That has required FERC to move from merely approving cost-based rates for transmission services to enacting new regulations that would make it more attractive to invest in transmission infrastructure without offending the ''just and reasonable'' rate standard. (author)

Snarr, Steven W.

2010-03-15T23:59:59.000Z

352

2007 EPRI Heat Rate Improvement Conference Proceedings  

Science Conference Proceedings (OSTI)

Due to the rising cost of fuel and the growing possibility of carbon taxes in the not-too-distant future, utilities are once again focusing on the heat rate and performance of coal-fired power plants. The fifteenth Heat Rate Improvement Conference is the latest in this series of meetings designed to assist utilities in addressing problems with power plant performance and in identifying cost-effective solutions for achieving and maintaining heat rate improvement.

2007-03-30T23:59:59.000Z

353

Proceedings 2013 Heat Rate Improvement Conference  

Science Conference Proceedings (OSTI)

With the rising cost of fuel and the strong possibility of CO2 emissions regulations and limitations in the near future, utilities and power generation companies are focusing on power plant heat rate and performance. The 18th Heat Rate Improvement Conference is the latest in a series of meetings designed to assist attendees in addressing problems with power plant performance and identifying cost-effective solutions for achieving and sustaining heat rate ...

2013-04-05T23:59:59.000Z

354

DETERMINATION OF DEPOSITION RATES FOR COOKING ...  

Science Conference Proceedings (OSTI)

... All calculations of deposition rates were made after ... the in- duct electrostatic precipitator increased the ... (1985) measured the performance of several ...

2005-10-07T23:59:59.000Z

355

Utility Rate Discounts | Open Energy Information  

Open Energy Info (EERE)

Discounts Discounts Jump to: navigation, search A few electric utilities offer rate discounts to encourage residential energy efficiency. For homes that meet certain energy efficiency criteria, such as those established by the federal Energy Star program, the owner or tenant is awarded a percentage discount on each month’s electric bill. [1] Contents 1 Utility Rate Discount Incentives 2 References Utility Rate Discount Incentives CSV (rows 1 - 14) Incentive Incentive Type Place Applicable Sector Eligible Technologies Active Cleco Power - Power Miser New Home Program (Louisiana) Utility Rate Discount Louisiana Residential Building Insulation Central Air conditioners Clothes Washers Comprehensive Measures/Whole Building Doors Duct/Air sealing Furnaces Heat pumps

356

Rate Schedule PACI-T3  

NLE Websites -- All DOE Office Websites (Extended Search)

or rate schedule accepted or approved by the Federal Energy Regulatory Commission (FERC) or other regulatory bodies will be passed on to each relevant customer. The FERC's or...

357

DEC Asset Rating | CUBIC APPLE LTD  

U.S. Energy Information Administration (EIA)

NON-DOMESTIC ENERGY ... if you are worried about the DEC asset rating for your public building why not get in contact with Cubic Apple on 01529 300 ...

358

Available Technologies: Super High Rate Sputter Deposition  

Andre Anders of Berkeley Lab has developed a very high deposition rate magnetron sputtering wherein the surface of a target and the race track zone area of the ...

359

Rate Schedule CV-EID4  

NLE Websites -- All DOE Office Websites (Extended Search)

CV-EID3) UNITED STATES DEPARTMENT OF ENERGY WESTERN AREA POWER ADMINISTRATION CENTRAL VALLEY PROJECT SCHEDULE OF RATE FOR ENERGY IMBALANCE SERVICE Effective: October 1, 2011,...

360

Rate Schedule CV-SUR4  

NLE Websites -- All DOE Office Websites (Extended Search)

CV-SUR3) UNITED STATES DEPARTMENT OF ENERGY WESTERN AREA POWER ADMINISTRATION CENTRAL VALLEY PROJECT SCHEDULE OF RATE FOR SUPPLEMENTAL RESERVE SERVICE Effective: October 1, 2011,...

Note: This page contains sample records for the topic "ah rated pack" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


361

Rate Schedule CV-SPR4  

NLE Websites -- All DOE Office Websites (Extended Search)

CV-SPR3) UNITED STATES DEPARTMENT OF ENERGY WESTERN AREA POWER ADMINISTRATION CENTRAL VALLEY PROJECT SCHEDULE OF RATE FOR SPINNING RESERVE SERVICE Effective: October 1, 2011,...

362

Dose rate visualization of radioisotope thermoelectric generators  

DOE Green Energy (OSTI)

Advanced visualization techniques can be used to investigate gamma ray and neutron dose rates around complex dose rate intensive operations. A method has been developed where thousands of dose points are calculated using the MCNP(Monte Carlo N-Particle) computer code and then displayed to create color contour plots of the dose rate for complex geometries. Once these contour plots are created, they are sequenced together creating an animation to dynamically show how the dose rate changes with changes in the geometry or source over time.

Schwarz, R.A.; Kessler, S.F.; Tomaszewski, T.A.

1995-09-01T23:59:59.000Z

363

Rate Schedule CV-SPR4  

NLE Websites -- All DOE Office Websites (Extended Search)

Any charges or credits associated with the creation, termination, or modification to any tariff, contract, or rate schedule accepted or approved by the Federal Energy Regulatory...

364

Rate Schedule CV-SUR4  

NLE Websites -- All DOE Office Websites (Extended Search)

Any charges or credits associated with the creation, termination, or modification to any tariff, contract, or rate schedule accepted or approved by the Federal Energy Regulatory...

365

Corridor Rate Analysis Results - Energy Information Administration  

U.S. Energy Information Administration (EIA)

Energy Information Administration 113 ... with the pipeline company tariff rates obtained using the Federal Energy Regulatory Commission Automated System for Tariff

366

Optimization Online - Approximate Primal Solutions and Rate ...  

E-Print Network (OSTI)

Mar 29, 2007... limit as the number of subgradient iterations increases to infinity). Furthermore, no convergence rate results are known for these algorithms.

367

Method of controlling fusion reaction rates  

DOE Patents (OSTI)

This invention relates to a method of controlling the reaction rates in a nuclear fusion reactor; and more particularly, to the use of polarized nuclear fuel.

Kulsrud, R.M.; Furth, H.P.; Valeo, E.J.; Goldhaber, M.

1983-05-09T23:59:59.000Z

368

Rate Schedule CV-TPT7  

NLE Websites -- All DOE Office Websites (Extended Search)

OF ENERGY WESTERN AREA POWER ADMINISTRATION CENTRAL VALLEY PROJECT SCHEDULE OF RATE FOR TRANSMISSION OF WESTERN POWER BY OTHERS Effective: October 1, 2011, through September 30,...

369

Rate Schedule COTP-T3  

NLE Websites -- All DOE Office Websites (Extended Search)

COTP-T3 (Supersedes Schedule COTP-T2) UNITED STATES DEPARTMENT OF ENERGY WESTERN AREA POWER ADMINISTRATION CALIFORNIA-OREGON TRANSMISSION PROJECT SCHEDULE OF RATE FOR...

370

PEPTIDE FOLDING RATES FROM SINGLE-MOLECULE ...  

Science Conference Proceedings (OSTI)

... A. Myers, Daniel A. Gacek, Eric M. Peterson, Christopher B. Fox, Joel M ... These microscopic rates are used to estimate the free energy barrier to ...

371

Investigation of formaldehyde and acetaldehyde sampling rate...  

NLE Websites -- All DOE Office Websites (Extended Search)

formaldehyde and acetaldehyde sampling rate and ozone interference for passive deployment of Waters Sep-Pak XPoSure samplers Title Investigation of formaldehyde and acetaldehyde...

372

ORNL DAAC, global soil respiration rates  

NLE Websites -- All DOE Office Websites (Extended Search)

W. Raich and W. H. Schlesinger, the newly released data set contains soil respiration rates from sites in terrestrial and wetland ecosystems as reported in scientific literature...

373

Photovoltaic Degradation Rates -- An Analytical Review  

DOE Green Energy (OSTI)

As photovoltaic penetration of the power grid increases, accurate predictions of return on investment require accurate prediction of decreased power output over time. Degradation rates must be known in order to predict power delivery. This article reviews degradation rates of flat-plate terrestrial modules and systems reported in published literature from field testing throughout the last 40 years. Nearly 2000 degradation rates, measured on individual modules or entire systems, have been assembled from the literature, showing a median value of 0.5%/year. The review consists of three parts: a brief historical outline, an analytical summary of degradation rates, and a detailed bibliography partitioned by technology.

Jordan, D. C.; Kurtz, S. R.

2012-06-01T23:59:59.000Z

374

Rate Schedule CV-F13  

NLE Websites -- All DOE Office Websites (Extended Search)

FP customer allocation is equal to the annual PRR multiplied by the relevant FP percentage. The formula rate for FP power has three components. Component 1: FP Customer...

375

Definition: Facility Rating | Open Energy Information  

Open Energy Info (EERE)

any equipment comprising the facility.1 Related Terms reactive power, equipment rating, power, smart grid References Glossary of Terms Used in Reliability Standards An inl...

376

HEART RATE AS A MONITOR FOR METABOLIC RATE IN CAPTIVE JUVENILE STELLER SEA LIONS (EUMETOPIAS JUBATUS)  

E-Print Network (OSTI)

HEART RATE AS A MONITOR FOR METABOLIC RATE IN CAPTIVE JUVENILE STELLER SEA LIONS (EUMETOPIAS COLUMBIA 0Jan M. Mcl'hee, 2001 #12;ABSTRACT The potential use of heart rate to monitor energy expenditure a relationship exists between heart rate @I) and oxygen consumption ( ~ 0 ~ )in captive sea lions while swimming

377

University of California -Office of Loan Programs Historical STIP Quarterly Rate of Return for MOP Rate  

E-Print Network (OSTI)

University of California - Office of Loan Programs Historical STIP Quarterly Rate of Return for MOP - Office of Loan Programs Historical STIP Quarterly Rate of Return for MOP Rate Quarterly MOP Rate MOP.00% 03/31/86 7.987% 8.35% 8.35% (1) Calculated as the total STIP income earned for each period

Russell, Lynn

378

Richard Cantor Rating Transitions and Defaults Conditional on Watchlist, Outlook and Rating History Summary  

E-Print Network (OSTI)

This report documents global corporate credit rating transition and default rates during the 1995-2003 period conditional on the full information in Moody's published credit opinions, which, in addition to the current credit rating, include prior rating actions and current rating outlooks and reviews. The primary findings of this study are: Moodys rating system management practices attempt to limit rating reversals and dampen rating change volatility and, as a consequence, different issuers carrying the same rating may have different risks of rating migration and default. As noted in Moodys prior research dating back to 1993, recently downgraded issuers have a greater likelihood of future rating downgrades and default than do recently upgraded issuers. For example, obligors downgraded in the past twelve months are eight times more likely to be downgraded than upgraded in the next year. Downgraded issuers are eleven times more likely to default over one year than upgraded issuers. Moodys rating outlooks and reviews are used to signal the likely direction and timing of future rating actions and the evolution of default risk. For example, at a one-year time horizon, issuers with negative outlooks are seven times more likely to be downgraded than upgraded; issuers with positive outlooks are nearly twice as likely to be upgraded as downgraded; and issuers with stable outlooks have the highest probability of no rating change. Default rates within a given rating category also vary systematically by outlook status. For example,

unknown authors

2004-01-01T23:59:59.000Z

379

Video digest based on heart rate  

Science Conference Proceedings (OSTI)

In video digesting, not only features and keywords extracted from a content itself but viewer's input are essential to incorporate subjective impressions and perceived importance. The present study aims at providing heart rate based arousal level as ... Keywords: affect, emotion, heart rate, psychophysiology, video analysis, video digest

Satoshi Toyosawa; Takashi Kawai

2007-08-01T23:59:59.000Z

380

Switching rates of multi-step reactions  

E-Print Network (OSTI)

We consider a switching rate of a meta-stable reaction scheme, which includes reactions with arbitrary steps, e.g. $kA\\to(k+r)A$. Employing WKB approximation, controlled by a large system size, we evaluate both the exponent and the pre-exponential factor for the rate. The results are illustrated on a number of examples.

Escudero, Carlos

2008-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "ah rated pack" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


381

Quasi-Dynamic Rating Pilot Projects  

Science Conference Proceedings (OSTI)

EPRI's DTCR technology, which encompasses a number of software tools, hardware tools, and methodologies, offers near-term solutions to overhead line rating problems. The Quasi-Dynamic Rating (QDR) concepts and tools developed in the 2004 pilot project are presented in this report.

2004-12-27T23:59:59.000Z

382

Method of controlling fusion reaction rates  

DOE Patents (OSTI)

A method of controlling the reaction rates of the fuel atoms in a fusion reactor comprises the step of polarizing the nuclei of the fuel atoms in a particular direction relative to the plasma confining magnetic field. Fusion reaction rates can be increased or decreased, and the direction of emission of the reaction products can be controlled, depending on the choice of polarization direction.

Kulsrud, Russell M. (Princeton, NJ); Furth, Harold P. (Princeton, NJ); Valeo, Ernest J. (Princeton Junction, NJ); Goldhaber, Maurice (Bayport, NY)

1988-01-01T23:59:59.000Z

383

Nuclear Reaction Rates and Carbon Star Formation  

E-Print Network (OSTI)

We have studied how the third dredge-up and the carbon star formation in low-mass Asymptotic Giant Branch stars depends on certain key nuclear reaction rates. We find from a set of complete stellar evolution calculations of a 2Msun model with Z=0.01 including mass loss, that varying either the N14(p,g)O15 or the 3-alpha reaction rate within their uncertainties as given in the NACRE compilation results in dredge-up and yields that differ by a factor of 2. Model tracks with a higher rate for the 3-alpha rate and a lower rate for the N14(p,g)O15 reaction both show more efficient third dredge-up. New experimental results for the N14(p,g)O15 reaction rates are surveyed, yielding a rate which is about 40% lower than the tabulated NACRE rate, and smaller than NACRE's lower limit. We discuss the possible implications of the revised nuclear reaction stellar evolution calculations that aim to reproduce the observed carbon star formation at low mass, which requires efficient third dredge-up.

Falk Herwig; Sam M. Austin

2004-08-21T23:59:59.000Z

384

Theoretical cosmic Type Ia supernova rates  

E-Print Network (OSTI)

The aim of this work is the computation of the cosmic Type Ia supernova rates at very high redshifts (z>2). We adopt various progenitor models in order to predict the number of explosions in different scenarios for galaxy formation and to check whether it is possible to select the best delay time distribution model, on the basis of the available observations of Type Ia supernovae. We also computed the Type Ia supernova rate in typical elliptical galaxies of different initial luminous masses and the total amount of iron produced by Type Ia supernovae in each case. It emerges that: it is not easy to select the best delay time distribution scenario from the observational data and this is because the cosmic star formation rate dominates over the distribution function of the delay times; the monolithic collapse scenario predicts an increasing trend of the SN Ia rate at high redshifts whereas the predicted rate in the hierarchical scheme drops dramatically at high redshift; for the elliptical galaxies we note that the predicted maximum of the Type Ia supernova rate depends on the initial galactic mass. The maximum occurs earlier (at about 0.3 Gyr) in the most massive ellipticals, as a consequence of downsizing in star formation. We find that different delay time distributions predict different relations between the Type Ia supernova rate per unit mass at the present time and the color of the parent galaxies and that bluer ellipticals present higher supernova Type Ia rates at the present time.

R. Valiante; F. Matteucci; S. Recchi; F. Calura

2008-07-15T23:59:59.000Z

385

Seedskadee Participating Project Power Sales Rate History  

NLE Websites -- All DOE Office Websites (Extended Search)

Power Sales Rate History Updated: 1022009 Rate Schedule Effective Dates Energy (MillskWh) Capacity (kW-mo.) Combined (MillskWh) R4-F1 thru 474 3.000 1.275 6.000 UC-F1 4...

386

Utility Rate | OpenEI Community  

Open Energy Info (EERE)

Utility Rate Utility Rate Home > Features > Groups Content Group Activity By term Q & A Feeds Content type Blog entry Discussion Document Event Poll Question Keywords Author Apply Ewilson FYI, OpenEI now accommodates t... Posted by: Ewilson 20 Sep 2013 - 11:58 99thin Very useful information. Thank... Posted by: 99thin 9 Sep 2013 - 00:19 Rmckeel The utility rate database version 1 API is now deprecated Posted by: Rmckeel 6 Sep 2013 - 14:00 There comes a time in every API version's lifecycle when it needs to be deprecated. OpenEI's utility rate database version 1 API has been in use since the inception of the database in 2010. As... Tags: API, Utility Rates NickL Glad I could help get you on t... Posted by: NickL 4 Sep 2013 - 07:41 Glad I could help get you on the right track Myles. There is not as simple

387

International Rates | OpenEI Community  

Open Energy Info (EERE)

International Rates International Rates Home > Groups > Utility Rate Nsbowde's picture Submitted by Nsbowde(12) Member 10 July, 2012 - 11:27 Per the town hall discussion yestereday, I have a link to a tariff database assembled by the Energy Regulators Regional Association. There is no free access and reproduction of the information without ERRA consent is prohibited, but nonetheless here it is. I have some friends in ERRA, so maybe future collaboration could be possible. http://www.erranet.org/Products/TariffDatabase Nick Groups: Utility Rate Login to post comments Nsbowde's blog Comments Rmckeel Rmckeel1 year 26 weeks ago International rates Thanks for the info, Nick! On a side note, when we move our blog over to OpenEI communities, content like this blog entry will be more visible on

388

Utility Rate | OpenEI Community  

Open Energy Info (EERE)

Utility Rate Utility Rate Home > Utility Rate > Posts by term > Utility Rate Content Group Activity By term Q & A Feeds Term: American Clean Skies Foundation Type Term Title Author Replies Last Post sort icon Blog entry American Clean Skies Foundation Nominations open for $250,000 Multimedia Clean Energy prizes Graham7781 2 Oct 2012 - 13:01 Groups Menu You must login in order to post into this group. Recent content There is currently no way to s... ranking of utilities by demand charge? FYI, OpenEI now accommodates t... Very useful information. Thank... The utility rate database version 1 API is now deprecated more Group members (28) Managers: Dloomis Rmckeel Sfomail Recent members: MSiira Apin101 Lissacoffey Denizurla Bazouing Gdavis Shehant Anapettirossi Abkatzman

389

Definition: Equipment Rating | Open Energy Information  

Open Energy Info (EERE)

Rating Rating Jump to: navigation, search Dictionary.png Equipment Rating The maximum and minimum voltage, current, frequency, real and reactive power flows on individual equipment under steady state, short-circuit and transient conditions, as permitted or assigned by the equipment owner.[1] Also Known As Standard current ratings Related Terms reactive power, smart grid References ↑ Glossary of Terms Used in Reliability Standards An i LikeLike UnlikeLike You like this.Sign Up to see what your friends like. nline Glossary Definition Retrieved from "http://en.openei.org/w/index.php?title=Definition:Equipment_Rating&oldid=502535" Categories: Definitions ISGAN Definitions What links here Related changes Special pages Printable version Permanent link Browse properties

390

OpenEI Community - Utility Rates  

Open Energy Info (EERE)

The utility rate The utility rate database version 1 API is now deprecated http://en.openei.org/community/blog/utility-rate-database-version-1-api-now-deprecated There comes a time in every API version's lifecycle when it needs to be deprecated.OpenEI's utility rate database version 1 API has been in use since the inception of the database in 2010.  As Illinois State University has taken a commanding lead of the project and its data curation, we have updated the schema and API to version 2 to present a richer spectrum of utility rate data.

391

Utility Rate | OpenEI Community  

Open Energy Info (EERE)

Utility Rate Utility Rate Home > Utility Rate > Posts by term > Utility Rate Content Group Activity By term Q & A Feeds Term: challenge Type Term Title Author Replies Last Post sort icon Discussion challenge 2013 Civic Hacking Day Ideas Rmckeel 1 22 May 2013 - 08:23 Groups Menu You must login in order to post into this group. Recent content There is currently no way to s... ranking of utilities by demand charge? FYI, OpenEI now accommodates t... Very useful information. Thank... The utility rate database version 1 API is now deprecated more Group members (28) Managers: Dloomis Rmckeel Sfomail Recent members: MSiira Apin101 Lissacoffey Denizurla Bazouing Gdavis Shehant Anapettirossi Abkatzman BijouLulla Vbugnion Marklane Cbonsig Verdel3c Wisconsin Weatherall Windows Payne

392

Method for Determining Solids Circulation Rate  

NLE Websites -- All DOE Office Websites (Extended Search)

Determining Solids Circulation Rate Determining Solids Circulation Rate Contact NETL Technology Transfer Group techtransfer@netl.doe.gov May 2012 Opportunity Research is currently active on the patented technology "Method for Determining Solids Circulation Rate." The technology is available for licensing and/or further collaborative research from the U.S. Department of Energy's National Energy Technology Laboratory. Overview This invention provides a method to measure the rate of solids circulation, particularly in those applications where the solids are recycled back to pro- cesses for further use. The applications include processes such as circulating fluidized bed gasifiers and combustors, as well as chemical looping. In the above applications, determining solids circulation rates is needed to

393

gas rates | OpenEI Community  

Open Energy Info (EERE)

gas rates gas rates Home > Groups > Utility Rate Are there Gas Utility Rates available in OpenEI? Submitted by Nlong on 11 July, 2012 - 11:41 1 answer Points: 1 Hi, OpenEI doesn't have NG utility rates as far as I'm aware. That may be a dataset that is added in the future. You can access natural gas prices by utility and sector by downloading the EIA-176 form from the Energy Information Administration. I've included some links to help you find your way. http://205.254.135.7/survey/form/eia_176/efs176.cfm http://www.eia.gov/oil_gas/natural_gas/applications/eia176query_historical.html -Sfomail Sfomail on 12 July, 2012 - 12:04 Groups Menu You must login in order to post into this group. Recent content There is currently no way to s... ranking of utilities by demand charge?

394

Atomic multipole relaxation rates near surfaces  

E-Print Network (OSTI)

The spontaneous relaxation rates for an atom in free space and close to an absorbing surface are calculated to various orders of the electromagnetic multipole expansion. The spontaneous decay rates for dipole, quadrupole and octupole transitions are calculated in terms of their respective primitive electric multipole moments and the magnetic relaxation rate is calculated for the dipole and quadrupole transitions in terms of their respective primitive magnetic multipole moments. The theory of electromagnetic field quantization in magnetoelectric materials is used to derive general expressions for the decay rates in terms of the dyadic Green function. We focus on the decay rates in free space and near an infinite half space. For the decay of atoms near to an absorbing dielectric surface we find a hierarchy of scaling laws depending on the atom-surface distance z.

Crosse, J A

2009-01-01T23:59:59.000Z

395

Atomic multipole relaxation rates near surfaces  

E-Print Network (OSTI)

The spontaneous relaxation rates for an atom in free space and close to an absorbing surface are calculated to various orders of the electromagnetic multipole expansion. The spontaneous decay rates for dipole, quadrupole and octupole transitions are calculated in terms of their respective primitive electric multipole moments and the magnetic relaxation rate is calculated for the dipole and quadrupole transitions in terms of their respective primitive magnetic multipole moments. The theory of electromagnetic field quantization in magnetoelectric materials is used to derive general expressions for the decay rates in terms of the dyadic Green function. We focus on the decay rates in free space and near an infinite half space. For the decay of atoms near to an absorbing dielectric surface we find a hierarchy of scaling laws depending on the atom-surface distance z.

J. A. Crosse; Stefan Scheel

2009-01-20T23:59:59.000Z

396

Chaos regularization of quantum tunneling rates  

Science Conference Proceedings (OSTI)

Quantum tunneling rates through a barrier separating two-dimensional, symmetric, double-well potentials are shown to depend on the classical dynamics of the billiard trajectories in each well and, hence, on the shape of the wells. For shapes that lead to regular (integrable) classical dynamics the tunneling rates fluctuate greatly with eigenenergies of the states sometimes by over two orders of magnitude. Contrarily, shapes that lead to completely chaotic trajectories lead to tunneling rates whose fluctuations are greatly reduced, a phenomenon we call regularization of tunneling rates. We show that a random-plane-wave theory of tunneling accounts for the mean tunneling rates and the small fluctuation variances for the chaotic systems.

Pecora, Louis M.; Wu Dongho [Materials Physics and Sensors, US Naval Research Laboratory, Washington, DC 20375 (United States); Lee, Hoshik [Department of Physics, College of William and Mary, Williamsburg, Virginia 23187 (United States); Antonsen, Thomas; Lee, Ming-Jer; Ott, Edward [Physics and Electrical Engineering Departments, University of Maryland, College Park, Maryland 20742 (United States)

2011-06-15T23:59:59.000Z

397

Home Energy Ratings and Building Performance  

E-Print Network (OSTI)

This paper provides an overview of the Home Energy Rating System (HERS). A short summary of the origination and history of the HERS system will lead to a more detailed description of the inspection and testing protocol. The HERS rating provides an accepted method to determine home efficiency based on standards developed and overseen by the Residential Energy Services Network (RESNET), a not-for-profit corporation. The paper will discuss the effect of various building systems and effects of local climate as they affect the rating score of a proposed or completed structure. The rating is used to determine the most cost effective mechanical systems, building envelope design including window and door types, effect of various roofing materials and radiant barriers. The paper will conclude by comparing specifics of an actual report to the construction characteristics of a home as they relate to the HERS Rating and the result.

Gardner, J.C.

2008-12-01T23:59:59.000Z

398

Utility Rate | OpenEI Community  

Open Energy Info (EERE)

Utility Rate Utility Rate Home > Utility Rate > Posts by term > Utility Rate Content Group Activity By term Q & A Feeds Term: data Type Term Title Author Replies Last Post sort icon Blog entry data Commercial and Residential Hourly Load Data Now Available on OpenEI! Sfomail 17 May 2013 - 12:03 Blog entry data IRENA launches global atlas of renewable energy potential Graham7781 11 Feb 2013 - 15:18 Groups Menu You must login in order to post into this group. Recent content FYI, OpenEI now accommodates t... Very useful information. Thank... The utility rate database version 1 API is now deprecated Glad I could help get you on t... Nick, Thanks very much! That... more Group members (25) Managers: Dloomis Rmckeel Sfomail Recent members: Denizurla Bazouing Gdavis

399

Merger Rates of Dark-Matter Haloes  

E-Print Network (OSTI)

We derive analytic merger rates for dark-matter haloes within the framework of the Extended Press-Schechter (EPS) formalism. These rates become self-consistent within EPS once we realize that the typical merger in the limit of a small time-step involves more than two progenitors, contrary to the assumption of binary mergers adopted in earlier studies. We present a general method for computing merger rates that span the range of solutions permitted by the EPS conditional mass function, and focus on a specific solution that attempts to match the merger rates in N-body simulations. The corrected EPS merger rates are more accurate than the earlier estimates of Lacey & Cole, by ~20% for major mergers and by up to a factor of ~3 for minor mergers of mass ratio 1:10^4. Based on the revised merger rates, we provide a new algorithm for constructing Monte-Carlo EPS merger trees, that could be useful in Semi-Analytic Modeling. We provide analytic expressions and plot numerical results for several quantities that are very useful in studies of galaxy formation. This includes (a) the rate of mergers of a given mass ratio per given final halo, (b) the fraction of mass added by mergers to a halo, and (c) the rate of mergers per given main progenitor. The creation and destruction rates of haloes serve for a self-consistency check. Our method for computing merger rates can be applied to conditional mass functions beyond EPS, such as those obtained by the ellipsoidal collapse model or extracted from $N$-body simulations.

Eyal Neistein; Avishai Dekel

2008-02-04T23:59:59.000Z

400

On the Effectiveness of Rate Limiting Mechanisms  

E-Print Network (OSTI)

One class of worm defense techniques that received attention of late is to rate limit outbound traffic to contain fast spreading worms. Several proposals of rate limiting techniques have appeared in the literature, each with a different take on the impetus behind rate limiting. This paper presents an empirical analysis on different rate limiting schemes using real traffic and attack traces from a sizable network. In the analysis we isolate and investigate the impact of the critical parameters for each scheme and seek to understand how these parameters might be set in realistic network settings. Analysis shows that using DNS-based rate limiting has substantially lower error rates than schemes based on other traffic statistics. The empirical analysis additionally brings to light a number of issues with respect to rate limiting in practice. We explore the impact of these issues in the context of general worm containment. Acknowledgments: We thank the members and companies of the PDL Consortium for their support. This work was partially supported by the National Science Foundation under Grant No. CNS-0433540 and ANI-0326472.

Cynthia Wong; Stan Bielski; Ahren Studer; Chenxi Wang

2005-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "ah rated pack" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


401

What Is the New Normal Unemployment Rate?  

E-Print Network (OSTI)

Recent labor markets developments, including mismatches in the skills of workers and jobs, extended unemployment benefits, and very high rates of long-term joblessness, may be impeding the return to normal unemployment rates of around 5%. An examination of alternative measures of labor market conditions suggests that the normal unemployment rate may have risen as much as 1.7 percentage points to about 6.7%, although much of this increase is likely to prove temporary. Even with such an increase, sizable labor market slack is expected to persist for years. In the past, the U.S. labor market has proven to be very flexible and recessions have not usually been followed by long-lasting increases in the unemployment rate. But, in the wake of the most recent recession, many economists are concerned that developments such as mismatches in the skills of workers and jobs, extended unemployment benefits, and a rise in long-term joblessness may have raised the normal or natural rate of unemployment above the 5 % level that was thought to be typical before the downturn. Indeed, a few economists have gone so far as to argue that the rise in the unemployment rate to its current level of 9 % primarily reflects an increase in the natural rate, implying there is little slack in labor markets and therefore little downward pressure on inflation. This Economic Letter

Weidner; John C. Williams

2011-01-01T23:59:59.000Z

402

Rate Schedule CV-RFS4  

NLE Websites -- All DOE Office Websites (Extended Search)

RFS4 RFS4 (Supersedes Schedule CV-RFS3) UNITED STATES DEPARTMENT OF ENERGY WESTERN AREA POWER ADMINISTRATION CENTRAL VALLEY PROJECT SCHEDULE OF RATE FOR REGULATION AND FREQUENCY RESPONSE SERVICE Effective: October 1, 2011, through September 30, 2016. Available: Within the marketing area served by the Western Area Power Administration (Western), Sierra Nevada Customer Service Region. Applicable: To customers receiving Regulation and Frequency Response Service (regulation). Character and Conditions of Service: Regulation is necessary to provide for the continuous balancing of resources and interchange with load and for maintaining scheduled interconnection frequency at 60-cycles per second. Formula Rate: The formula rate for regulation includes three components:

403

Considerations for How to Rate CPV  

DOE Green Energy (OSTI)

The concentrator photovoltaic (CPV) industry is introducing multiple products into the marketplace, but, as yet, the; community has not embraced a unified method for assessing a nameplate rating. The choices of whether to use 850,; 900, or 1000 W/m2 for the direct-normal irradiance and whether to link the rating to ambient or cell temperature will; affect how CPV modules are rated and compared with other technologies. This paper explores the qualitative and; quantitative ramifications of these choices using data from two multi-junction CPV modules and two flat-plate; modules.

Kurtz, S.; Miller, M.; Marion, B.; Emery, K.; McConnell, R.; Surendran, S.; Kimber, A.

2011-02-01T23:59:59.000Z

404

Measuring Degradation Rates Without Irradiance Data  

DOE Green Energy (OSTI)

A method to report PV system degradation rates without using irradiance data is demonstrated. First, a set of relative degradation rates are determined by comparing daily AC final yields from a group of PV systems relative to the average final yield of all the PV systems. Then, the difference between relative and absolute degradation rates is found from a statistical analysis. This approach is verified by comparing to methods that utilize irradiance data. This approach is significant because PV systems are often deployed without irradiance sensors, so the analysis method described here may enable measurements of degradation using data that were previously thought to be unsuitable for degradation studies.

Pulver, S.; Cormode, D.; Cronin, A.; Jordan, D.; Kurtz, S.; Smith, R.

2011-02-01T23:59:59.000Z

405

Data Fusion for Improved Respiration Rate Estimation  

E-Print Network (OSTI)

We present an application of a modified Kalman-Filter (KF) framework for data fusion to the estimation of respiratory rate from multiple physiological sources which is robust to background noise. A novel index of the ...

Nemati, Shamim

406

Utility Rate | OpenEI Community  

Open Energy Info (EERE)

Utility Rate Utility Rate Home > Utility Rate > Posts by term Content Group Activity By term Q & A Feeds American Clean Skies Foundation (1) API (3) Apps (1) bug (1) building load (1) building load data (1) challenge (1) clean energy (1) commercial load (1) data (2) dataset (1) datasets (1) developer (5) DOE (1) EIA (1) electric load data (1) energy efficiency (1) Energy Visions Prize (1) EZFeed (1) FOA (1) funding (1) Global Atlas (1) hackathon (1) Illinois State University (1) Incentives and Policies (1) 1 2 3 next › last » Groups Menu You must login in order to post into this group. Recent content There is currently no way to s... ranking of utilities by demand charge? FYI, OpenEI now accommodates t... Very useful information. Thank... The utility rate database version 1 API is now deprecated

407

On-site Housing Rates | Staff Services  

NLE Websites -- All DOE Office Websites (Extended Search)

Rates Rates Effective February 1, 2013 Rates for Occupancy < 30-Days Guest House* Single/Double: US $105.00/day Housekeeping service is provided on all working days. *Alternatives to the Guest House - When family-type accommodations are assigned to temporary or transient personnel, Guest House rates as set forth above will apply. The total will not exceed one months' rent for a unit occupied for 30 days or less. When such assignment is necessary due to lack of adequate Guest House accommodations, housekeeping service is provided on working days; for reservations staying seven days or less. Residence Houses Curie House: US $42.00/day Cavendish House: US $42.00/day Compton House: US $42.00/day Housekeeping service for all residence houses are provided three times per

408

Definition: Rated power | Open Energy Information  

Open Energy Info (EERE)

Definition Definition Edit with form History Facebook icon Twitter icon » Definition: Rated power Jump to: navigation, search Dictionary.png Rated power The power output of a device under specific or nominal operating conditions[1] View on Wikipedia Wikipedia Definition In electrical and electronic engineering, the power rating of a device is a guideline set by the manufacturer as a maximum power to be used with that device. This limit is usually set somewhat lower than the level where the device will be damaged, to allow a margin of safety. In devices which primarily dissipate electric power or convert it into mechanical power, such as resistors, electric motors, and speakers, the power rating given is usually the maximum power that can be safely dissipated by the

409

Utility Rate | OpenEI Community  

Open Energy Info (EERE)

Utility Rate Utility Rate Home > Groups > Groups > Utility Rate Content Group Activity By term Q & A Feeds There are no feeds from external sites for this group. Groups Menu You must login in order to post into this group. Groups Menu You must login in order to post into this group. Group members (28) Managers: Dloomis Rmckeel Sfomail Recent members: MSiira Apin101 Lissacoffey Denizurla Bazouing Gdavis Shehant Anapettirossi Abkatzman BijouLulla Vbugnion Marklane Cbonsig Verdel3c Wisconsin Weatherall Windows Payne Nlong Wzeng Recent content There is currently no way to s... ranking of utilities by demand charge? FYI, OpenEI now accommodates t... Very useful information. Thank... The utility rate database version 1 API is now deprecated more Group members (28) Managers: Dloomis Rmckeel Sfomail

410

NREL: Photovoltaics Research - Photovoltaic Energy Ratings Methods  

NLE Websites -- All DOE Office Websites (Extended Search)

Photovoltaic Energy Ratings Methods Validation Photovoltaic Energy Ratings Methods Validation The Photovoltaic (PV) Engineering group at NREL validates energy ratings methods by standards committees to establish an energy rating methodology. We are evaluating techniques to account for the impact on PV performance from variations in the spectral distribution of solar radiation. Two types of methods were evaluated for correcting the short-circuit current of PV modules for variations in the solar spectrum under clear skies: (1) empirical relationships based on air mass, and (2) use of spectral irradiance models and PV module spectral response data. Methods of the first type were the Sandia National Laboratories absolute air-mass function, or f(AMa), and the CREST air-mass function, or f(AM). The second

411

Historical river flow rates for dose calculations  

Science Conference Proceedings (OSTI)

Annual average river flow rates are required input to the LADTAP Computer Code for calculating offsite doses from liquid releases of radioactive materials to the Savannah River. The source of information on annual river flow rates used in dose calculations varies, depending on whether calculations are for retrospective releases or prospective releases. Examples of these types of releases are: Retrospective - releases from routine operations (annual environmental reports) and short term release incidents that have occurred. Prospective - releases that might be expected in the future from routine or abnormal operation of existing or new facilities (EIS`s, EID`S, SAR`S, etc.). This memorandum provides historical flow rates at the downstream gauging station at Highway 301 for use in retrospective dose calculations and derives flow rate data for the Beaufort-Jasper and Port Wentworth water treatment plants.

Carlton, W.H.

1991-06-10T23:59:59.000Z

412

Essays on exchange rates and electricity demand  

E-Print Network (OSTI)

This thesis examines two important issues in economic development: exchange rates and electricity demand and addresses methodological issues of using time series and panel data analysis to investigate important policy ...

Li, Xiangming, 1966-

1999-01-01T23:59:59.000Z

413

Can Anthropogenic Aerosols Decrease the Snowfall Rate?  

Science Conference Proceedings (OSTI)

Observations by Borys, Lowenthal, Cohn, and Brown in midlatitude orographic clouds show that for a given supercooled liquid water content, both the riming and the snowfall rates are smaller if the supercooled cloud has more cloud droplets as, for ...

U. Lohmann

2004-10-01T23:59:59.000Z

414

Rating the energy performance of buildings  

SciTech Connect

In order to succeed in developing a more sustainable society, buildings will need to be continuously improved. This paper discusses how to rate the energy performance of buildings. A brief review of recent approaches to energy rating is presented. It illustrates that there is no single correct or wrong concept, but one needs to be aware of the relative impact of the strategies. Different strategies of setting energy efficiency standards are discussed and the advantages of the minimum life cycle cost are shown. Indicators for building energy rating based on simulations, aggregated statistics and expert knowledge are discussed and illustrated in order to demonstrate strengths and weaknesses of each approach. In addition, the importance of considering the level of amenities offered is presented. Attributes of a rating procedure based on three elements, flexible enough for recognizing different strategies to achieve energy conservation, is proposed.

Olofsson, Thomas; Meier, Alan; Lamberts, Roberto

2004-12-01T23:59:59.000Z

415

The legal case against standby rates  

Science Conference Proceedings (OSTI)

Under rates approved by many state commissions, on-site investments are blocked and/or dis-incentivized by policies that place the interest of utility shareholders before the interests of the public. (author)

Casten, Sean; Karegianes, Myra

2007-11-15T23:59:59.000Z

416

The Estimation of Snowfall Rate Using Visibility  

Science Conference Proceedings (OSTI)

The relationship between liquid equivalent snowfall rate and visibility is investigated using data collected at the National Center for Atmospheric Research Marshall Snowfall Test Site during two winter field seasons and using theoretical ...

Roy M. Rasmussen; Jothiram Vivekanandan; Jeffrey Cole; Barry Myers; Charles Masters

1999-10-01T23:59:59.000Z

417

Empirically Evaluating Divergence Rates of Atmospheric Trajectories  

Science Conference Proceedings (OSTI)

Observed Northern Hemisphere divergence rates of phase-space trajectories initially emanating from neighboring points are estimated, using a simple, seasonal, weakly GCM-dependent linear method applied to Ertel potential vorticity on the 315-K ...

Gidon Eshel

2006-02-01T23:59:59.000Z

418

Can Paleoceanographic Tracers Constrain Meridional Circulation Rates?  

Science Conference Proceedings (OSTI)

The ability of paleoceanographic tracers to constrain rates of transport is examined using an inverse method to combine idealized observations with a geostrophic model. Considered are the spatial distribution, accuracy, and types of tracers ...

Peter Huybers; Geoffrey Gebbie; Olivier Marchal

2007-02-01T23:59:59.000Z

419

Utility Rate | OpenEI Community  

Open Energy Info (EERE)

Utility Rate Home > Utility Rate > Posts by term > Utility Rate Content Group Activity By term Q & A Feeds Term: energy efficiency Type Term Title Author Replies Last Post sort icon Blog entry energy efficiency FOA aimed at growing expansive database of Renewable Energy and Energy Efficiency Incentives and Policies Graham7781 12 Dec 2012 - 11:30 Groups Menu You must login in order to post into this group. Recent content FYI, OpenEI now accommodates t... Very useful information. Thank... The utility rate database version 1 API is now deprecated Glad I could help get you on t... Nick, Thanks very much! That... more Group members (25) Managers: Dloomis Rmckeel Sfomail Recent members: Denizurla Bazouing Gdavis Shehant Anapettirossi Abkatzman BijouLulla Vbugnion

420

Utility Rate Discount | Open Energy Information  

Open Energy Info (EERE)

Discount Discount Jump to: navigation, search A few electric utilities offer rate discounts to encourage residential energy efficiency. For homes that meet certain energy efficiency criteria, such as those established by the federal Energy Star program, the owner or tenant is awarded a percentage discount on each month’s electric bill. [1] Utility Rate Discount Incentives CSV (rows 1 - 14) Incentive Incentive Type Place Applicable Sector Eligible Technologies Active Cleco Power - Power Miser New Home Program (Louisiana) Utility Rate Discount Louisiana Residential Building Insulation Central Air conditioners Clothes Washers Comprehensive Measures/Whole Building Doors Duct/Air sealing Furnaces Heat pumps Water Heaters Windows Yes Dominion North Carolina Power - Energy Saver Home Plus (North Carolina) Utility Rate Discount North Carolina Residential Water Heaters

Note: This page contains sample records for the topic "ah rated pack" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


421

Commercial Building Energy Asset Rating Workshop  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

BUILDING BUILDING ENERGY ASSET RATING WORKSHOP December 8-9, 2011 Washington, D.C. Nora Wang (Pacific Northwest National Laboratory) Will Gorrissen (Pacific Northwest National Laboratory) Molly McCabe (Hayden Tanner, LLC) Cody Taylor (Department of Energy) 1 I Asset Rating D.C. Workshop eere.energy.gov PRE-DECISIONAL Information included in this document is for discussion purposes and does not constitute the final program design. FOR INFORMATION ONLY 2 I Asset Rating D.C. Workshop eere.energy.gov Program Goals * Facilitate cost-effective investment in energy efficiency and reduce energy use in the commercial building sector * Establish a national standard for voluntary commercial building asset rating * Create a tool to help building owners identify and implement

422

Rating of Solar Energy Devices (Texas)  

Energy.gov (U.S. Department of Energy (DOE))

The Public Utility Commission has regulatory authority over solar energy devices installed and used in the state of Texas. The Commission can choose to adopt standards pertaining to the rating of...

423

Fort Devens: Cold Climate Market-Rate Townhomes Targeting HERS Index of 40, Harvard, Massachusetts (Fact Sheet)  

SciTech Connect

Achieving aggressive energy efficiency targets requires tight coordination and clear communication among owners, designers, builders, and subcontractors. For this townhome project, MassDevelopment, the quasi-governmental agency owner, selected Metric Development of Boston, teaming with the U.S. Department of Energy (DOE) Consortium for Advanced Residential Buildings (CARB) and Cambridge Seven Architects, to build very high performing market-rate homes. Fort Devens is part of a decommissioned army base in working-class Harvard, Massachusetts, approximately one hour northwest of Boston. The team proposed 12 net zero energy-ready townhomes, meaning that the application of renewable energy systems would result in annual net zero energy use in the homes. The homes were also designed to achieve a Home Energy Rating System (HERS) Index Score of 41 before adding renewables. For this project, CARB drew on its experience working with Rural Development Inc. on a series of affordable townhomes in northern Massachusetts. The team carefully planned the site to maximize solar access, daylighting, and efficient building forms. The basic strategy was to design a very efficient thermal enclosure while minimizing incremental cost increases compared with standard construction. Using BEopt modeling software, the team established the requirements of the enclosure and investigated multiple assembly options. They settled on double-wall construction with dense-pack cellulose fill. High performance vinyl windows (U-0.24, solar heat gain coefficient [SHGC]-0.22), a vented R-59 attic, and exceptional air sealing completed the package.

Metzger, C.; Zoeller, W.

2013-11-01T23:59:59.000Z

424

Calibration and Rating of Photovoltaics: Preprint  

SciTech Connect

Rating the performance of photovoltaic (PV) modules is critical to determining the cost per watt, and efficiency is useful to assess the relative progress among PV concepts. Procedures for determining the efficiency for PV technologies from 1-sun to low concentration to high concentration are discussed. We also discuss the state of the art in primary and secondary calibration of PV reference cells used by calibration laboratories around the world. Finally, we consider challenges to rating PV technologies and areas for improvement.

Emery, K.

2012-06-01T23:59:59.000Z

425

DWPF Macrobatch 2 Melt Rate Tests  

SciTech Connect

The Defense Waste Processing Facility (DWPF) canister production rate must be increased to meet canister production goals. Although a number of factors exist that could potentially increase melt rate, this study focused on two: (1) changes in frit composition and (2) changes to the feed preparation process to alter the redox of the melter feed. These two factors were investigated for Macrobatch 2 (sludge batch 1B) utilizing crucible studies and a specially designed ''melt rate'' furnace. Other potential factors that could increase melt rate include: mechanical mixing via stirring or the use of bubblers, changing the power skewing to redistribute the power input to the melter, and elimination of heat loss (e.g. air in leakage). The melt rate testing in FY00 demonstrated that melt rate can be improved by adding a different frit or producing a much more reducing glass by the addition of sugar as a reductant. The frit that melted the fastest in the melt rate testing was Frit 165. A paper stud y was performed using the Product Composition Control System (PCCS) to determine the impact on predicted glass viscosity, liquidus, durability, and operating window if the frit was changed from Frit 200 to Frit 165. PCCS indicated that the window was very similar for both frits. In addition, the predicted viscosity of the frit 165 glass was 46 poise versus 84 poise for the Frit 200 glass. As a result, a change from Frit 200 to Frit 165 is expected to increase the melt rate in DWPF without decreasing waste loading.

Stone, M.E.

2001-01-03T23:59:59.000Z

426

Changes in heart rate variability during fainting  

Science Conference Proceedings (OSTI)

Studies of heart rate variability in people who faint may yield insights into normal physiologic mechanisms which probably are dynamic. These insights might be gained because fainting appears to be due to a breakdown of these mechanisms. Tilt table testing reliably induces fainting in patients with a history of fainting and can be used to study these mechanisms. During tilt tests ending in fainting heart rate changes markedly

Robert Sheldon; Kenneth Riff

1991-01-01T23:59:59.000Z

427

Radiation Leukemogenesis at Low Dose Rates  

SciTech Connect

The major goals of this program were to study the efficacy of low dose rate radiation exposures for the induction of acute myeloid leukemia (AML) and to characterize the leukemias that are caused by radiation exposures at low dose rate. An irradiator facility was designed and constructed that allows large numbers of mice to be irradiated at low dose rates for protracted periods (up to their life span). To the best of our knowledge this facility is unique in the US and it was subsequently used to study radioprotectors being developed for radiological defense (PLoS One. 7(3), e33044, 2012) and is currently being used to study the role of genetic background in susceptibility to radiation-induced lung cancer. One result of the irradiation was expected; low dose rate exposures are ineffective in inducing AML. However, another result was completely unexpected; the irradiated mice had a very high incidence of hepatocellular carcinoma (HCC), approximately 50%. It was unexpected because acute exposures are ineffective in increasing HCC incidence above background. This is a potential important finding for setting exposure limits because it supports the concept of an ?inverse dose rate effect? for some tumor types. That is, for the development of some tumor types low dose rate exposures carry greater risks than acute exposures.

Weil, Michael; Ullrich, Robert

2013-09-25T23:59:59.000Z

428

Short GRBs: Rates and luminosity function implications  

E-Print Network (OSTI)

We compare the luminosity function and rate inferred from the BATSE short hard bursts (SHBs) peak flux distribution with the redshift and luminosity distributions of SHBs observed by Swift/HETE II. The Swift/HETE II SHB sample is incompatible with SHB population that follows the star formation rate. However, it is compatible with a distribution of delay times after the SFR. This would be the case if SHBs are associated with the mergers of double neutron star (DNS) systems. DNS may be ``primordial'' or can form dynamically by binary exchange interaction in globular clusters during core collapse. The implied SHB rates that we find range from \\sim 8 to \\sim 30h_(70)^3 Gpc^(-3)yr^(-1). This rate is a much higher than what was previously estimated and, when beaming is taken into account, it is comparable to the rate of neutron star mergers estimated from statistics of binary pulsars. If GRBs are produced in mergers the implied rate practically guarantees detection by LIGO II and possibly even by LIGO I.

Dafne Guetta

2006-10-13T23:59:59.000Z

429

SmartAHS and SHIFT Enhancements, Persistence and Query Interpretation  

E-Print Network (OSTI)

the PC version of the TCL/TK language, and this constituteslexer and parser tools, Tcl/Tk, gnu C compiler. This effortwith MS VC++ and also uses Tcl/Tk. The Tcl/Tk programming

Misener, Jim

2000-01-01T23:59:59.000Z

430

Cryptographic Algorithm Implementation Requirements For ESP And AH  

E-Print Network (OSTI)

Distribution of this draft is unlimited. Comments should be sent to the authors. This document is an Internet-Draft and is in full conformance with all provisions of Section 10 of RFC 2026. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF), its areas, and its working groups. Note that other groups may also distribute working documents as Internet-Drafts. Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress. " The list of current Internet-Drafts can be accessed at http://www.ietf.org/ietf/1id-abstracts.txt The list of Internet-Draft Shadow Directories can be accessed at

Donald E. Eastlake Rd

2004-01-01T23:59:59.000Z

431

Achievable Rate and Optimal Physical Layer Rate Allocation in Interference-Free Wireless Networks  

E-Print Network (OSTI)

We analyze the achievable rate in interference-free wireless networks with physical layer fading channels and orthogonal multiple access. As a starting point, the point-to-point channel is considered. We find the optimal physical and network layer rate trade-off which maximizes the achievable overall rate for both a fixed rate transmission scheme and an improved scheme based on multiple virtual users and superposition coding. These initial results are extended to the network setting, where, based on a cut-set formulation, the achievable rate at each node and its upper bound are derived. We propose a distributed optimization algorithm which allows to jointly determine the maximum achievable rate, the optimal physical layer rates on each network link, and an opportunistic back-pressure-type routing strategy on the network layer. This inherently justifies the layered architecture in existing wireless networks. Finally, we show that the proposed layered optimization approach can achieve almost all of the ergodic ...

Cui, Tao; Kliewer, Joerg

2009-01-01T23:59:59.000Z

432

Labor Market Frictions, Interest Rates, and Macroeconomic Policies  

E-Print Network (OSTI)

endogenous separation rate increases, that is the ?ow intoinduces higher real interest rate, increases the demand forendogenous separation rate increases. We assume match-speci?

Zhang, Ji

433

Relating Vehicle-Wildlife Crash Rates to Roadway Improvements  

E-Print Network (OSTI)

animal-vehicle crash rates experienced increases followingif the crash rates has a significant increase or decrease inshowed an increase in animal-vehicle crash rates, although

Young, Rhonda; Giessen, Steven Vander; Vokurka, Christopher Steven

2007-01-01T23:59:59.000Z

434

Transmission Rate in Partial Differential Equation in Epidemic Models.  

E-Print Network (OSTI)

??The rate at which susceptible individuals become infected is called the transmission rate. It is important to know this rate in order to study the (more)

Elkadry, Alaa

2013-01-01T23:59:59.000Z

435

Size structuring of planktonic communities : biological rates and ecosystem dynamics  

E-Print Network (OSTI)

measuring growth and mortality rates among Prochlorococcustemperature on metabolic rate. Science 293:2248-2251. Gregg,and temperature on metabolic rate. Science. 293:2248-2251.

Taniguchi, Darcy Anne Akiko

2013-01-01T23:59:59.000Z

436

Sustainability, Limited Substitutability and Non-Constant Social Discount Rates  

E-Print Network (OSTI)

and Non-constant Social Discount Rates ? int strict weaktal preservation, and the rate of discount, Quarterlyhorizon and the discount rate, Journal of Economic Theory

Traeger, Christian P.

2008-01-01T23:59:59.000Z

437

Freely Floating Exchange Rates Do Not Systematically Overshoot  

E-Print Network (OSTI)

Canadian-U.S. exchange rate, Review of Financial Economics,economy under flexible exchange rates, Journal of Monetary1976, Expectations and Exchange Rate Dynamics, Journal of

Pippenger, John

2008-01-01T23:59:59.000Z

438

Globalization, Macroeconomic Performance, and the Exchange Rates of Emerging Economies  

E-Print Network (OSTI)

The Impact of Exchange Rate Movements on U.S. Foreign Debt."Performance, and the Exchange Rates of Emerging Economies*volatility, exchange-rate regimes, institutions,

Obstfeld, Maurice

2004-01-01T23:59:59.000Z

439

After the Fall: East Asian Exchange Rates Since the Crisis  

E-Print Network (OSTI)

Case for Floating Exchange Rates in Asia. In Monetary and2005. Classifying Exchange Rate Regimes: Deeds vs. Words. Ronald I. 2005. Exchange Rates under the East Asian Dollar

Cohen, Benjamin J

2007-01-01T23:59:59.000Z

440

Estimating stress heterogeneity from aftershock rate  

E-Print Network (OSTI)

We estimate the rate of aftershocks triggered by a heterogeneous stress change, using the rate-and-state model of Dieterich [1994]. We show than an exponential stress distribution P(\\tau)~ exp(-\\tau/\\tau_0) gives an Omori law decay of aftershocks with time ~1/t^p, with an exponent p=1-A\\sigma_n/\\tau_0, where A is a parameter of the rate-and-state friction law, and \\sigma_n the normal stress. Omori exponent p thus decreases if the stress "heterogeneity" \\tau_0 decreases. We also invert the stress distribution P(\\tau) from the seismicity rate R(t), assuming that the stress does not change with time. We apply this method to a synthetic stress map, using the (modified) scale invariant "k^2" slip model [Herrero and Bernard, 1994]. We generate synthetic aftershock catalogs from this stress change. The seismicity rate on the rupture area shows a huge increase at short times, even if the stress decreases on average. This stochastic slip model gives a Gaussian stress distribution, but nevertheless produces an aftersho...

Helmstetter, A; Helmstetter, Agnes; Shaw, Bruce E.

2005-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "ah rated pack" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


441

Sodium tetraphenylborate solubility and dissolution rates  

DOE Green Energy (OSTI)

The rate of solid sodium tetraphenylborate (NaTPB) dissolution in In-Tank Precipitation salt solutions has been experimentally determined. The data indicates that the dissolution rate of solid NaTPB is a minor contributor the lag time experienced in the 1983 Salt Decontamination Demonstration Test and should not be considered as the rate determining step. Current analytical models for predicting the time to reach the composite lower flammability limit assume that the lag time is not more than 6 hours, and the data supports this assumption (i.e., dissolution by itself requires much less than 6 hours). The data suggests that another step--such as mass transport, the reaction of a benzene precursor or the mixing behavior--is the rate determining factor for benzene release to the vapor space in Tank 48H. In addition, preliminary results from this program show that the degree of agitation employed is not a significant parameter in determining the rate of NaTPB dissolution. As a result of this study, an improved equation for predicting equilibrium tetraphenylborate solubility with respect to temperature and sodium ion concentration has been determined.

Barnes, M.J.; Peterson, R.A.; Swingle, R.F.; Reeves, C.T.

1995-12-31T23:59:59.000Z

442

Resource supply shocks and the interest rate  

SciTech Connect

Using a model of optimal economic growth with exhaustible resources, the author focuses on a real shock as an essential element of a model of ecomomic fluctuations that contributes substantially to variations in the interest rate, and output. When there occurs a sudden negative resource supply shock, the rate of extraction of the resource declines. Along the optimal path with capital stock fixed in the short run, the output-capital ratio and the real interest rate fall instantaneously. The hypothesis is tested with the quarterly US data using estimation techniques of Vector Autoregressions (VARs). Included are five variables in the VAR model: crude oil price, price level, interest rate, industrial production, and copper price. The general vector autoregressive models are estimated with a prior distribution imposed on the parameters of the model. The period of fit is 1958 to 1983. Impulse response functions of the system and historical decompositions of the time series are investigated. Empirical studies support the derived working hypothesis that real interest rate falls instantaneously and then slowly recovers in the long run when there occurs a negative resource supply shock.

Kang, M.S.

1984-01-01T23:59:59.000Z

443

Intraclass Price Elasticity & Electric Rate Design  

E-Print Network (OSTI)

Electric rate design relies on cost incurrance for pricing and pricing structures. However, as utilities move into a marketing mode, rate design needs to respond more to customer reactions to pricing changes. Intraclass price elasticities aid rate designers by estimating customer behavior to change. Intraclass price elasticities vary with customer usage. The more energy used by a customer, the greater the amount of elasticity. For an industrial customer, this means that all energy consumed up to the amount necessary for base operations is relatively inelastic. All energy consumption beyond this becomes more elastic as usage increases. In the book "Innovative Electric Rates," John Chamberlin and Charles Dickson utilize an economic model to test conservation programs. This model utilizes intraclass price elasticities and has a direct use in current electric rate design. The model is a strong indicator of how best a company's electric prices and pricing structures manage demand-side growth, increase energy sales consumption, and aide in non-discriminatory economic development.

Gresham, K. E.

1987-09-01T23:59:59.000Z

444

Discount rates and demand-side management  

SciTech Connect

The standard economic analysis of of implied discount rates for energy-efficiency investment is wrong. First, consumers are not profit maximizing or economic optimizing agents with respect to energy. To the extent consumers make tradeoffs on some criteria other than energy costs, implied discount rates measure that other tradeoff, not the energy cost tradeoff. Second, to the extent that product pricing does not reflect tradeoffs between first cost and energy cost, there is no meaning to implied market discount rates based on these factors. Related to this misinterpretation of consumer and market discount rates is the issue of consumer and utility self-interest. To the extent that utilities can capitalize on the energy-inefficient investment behavior of individuals through DSM programs, it is in their interest and the ratepayer's interest to do so. Considerable evidence suggests that implied discount rates convey extremely misleading information about the level of this underinvestment. Drawing inferences about the value of DSM programs from this information is similarly misleading. An economic explanation of consumer and marker behavior suggests that such underinvestment is both rational and common and that large gains may be achieved through DSM. Societal welfare would be improved if utilities aggressively capitalized on the widespread consumer underinvestment in energy efficiency by incorporating DSM in their resource planning processes.

Chernoff, H.

1993-02-01T23:59:59.000Z

445

Utility Rate | OpenEI Community  

Open Energy Info (EERE)

Utility Rate Utility Rate Home > Groups Content Group Activity By term Q & A Feeds Share your own status updates, and follow the updates & activities of others by creating your own account. Or, remember to log in If you already have an account. Groups Menu You must login in order to post into this group. Recent content There is currently no way to s... ranking of utilities by demand charge? FYI, OpenEI now accommodates t... Very useful information. Thank... The utility rate database version 1 API is now deprecated more Group members (28) Managers: Dloomis Rmckeel Sfomail Recent members: MSiira Apin101 Lissacoffey Denizurla Bazouing Gdavis Shehant Anapettirossi Abkatzman BijouLulla Vbugnion Marklane Cbonsig Verdel3c Wisconsin Weatherall Windows Payne Nlong Wzeng 429 Throttled (bot load)

446

Property:HeatRate | Open Energy Information  

Open Energy Info (EERE)

HeatRate HeatRate Jump to: navigation, search This is a property of type Number. Pages using the property "HeatRate" Showing 25 pages using this property. (previous 25) (next 25) A AES Mendota Biomass Facility + 17,873.6 + APS Biomass I Biomass Facility + 8,911 + Acme Landfill Biomass Facility + 12,916.67 + Adrian Energy Associates LLC Biomass Facility + 13,170.6 + Agrilectric Power Partners Ltd Biomass Facility + 17,327.1 + Al Turi Biomass Facility + 15,600.2 + Alabama Pine Pulp Biomass Facility + 15,826.23 + Albany Landfill Gas Utilization Project Biomass Facility + 11,913.9 + Altamont Gas Recovery Biomass Facility + 10,500 + American Canyon Power Plant Biomass Facility + 10,886.8 + American Ref-Fuel of Delaware Valley Biomass Facility + 18,674.9 +

447

Event loss rates and readout chips  

E-Print Network (OSTI)

98-57 The LHCb experiment aims at a deadtimeless readout of B­events at a primary bunch crossing rate of 40 MHz. In order to achieve this goal, information from all events must be stored in a pipeline with latency matched to the time needed for the Level 0 trigger decision. Accepted events, which constitute only a small fraction of the total sample, are stored in a fifo of a certain depth and read out with a fixed clock rate. The fifo, also referred to as multi­event or derandomizing buffer, is needed in order to even out statistical fluctuations in the trigger rate. Apart from the length of the pipeline, which determines the maximum latency of the chip, the crucial parameter characterizing a readout chip is the fraction of triggers lost due to limitations of the chip's architecture. This note describes how the different design parameters and operation conditions determine the chip's performance.

Schmelling, M

1998-01-01T23:59:59.000Z

448

The Cosmic Stellar Birth and Death Rates  

E-Print Network (OSTI)

The cosmic stellar birth rate can be measured by standard astronomical techniques. It can also be probed via the cosmic stellar death rate, though until recently, this was much less precise. However, recent results based on measured supernova rates, and importantly, also on the attendant diffuse fluxes of neutrinos and gamma rays, have become competitive, and a concordant history of stellar birth and death is emerging. The neutrino flux from all past core-collapse supernovae, while faint, is realistically within reach of detection in Super-Kamiokande, and a useful limit has already been set. I will discuss predictions for this flux, the prospects for neutrino detection, the implications for understanding core-collapse supernovae, and a new limit on the contribution of type-Ia supernovae to the diffuse gamma-ray background.

John F. Beacom

2006-02-05T23:59:59.000Z

449

On the Rate of Spontaneous Magnetic Reconnection  

E-Print Network (OSTI)

Magnetic reconnection is a topological rearrangement of the magnetic field lines, leading to the release of magnetic energy, which is thought to be associated with solar flares, coronal mass ejections and magnetospheric storms. Despite magnetic field lines are supposed to be frozen into the well-conducting plasma, the reconnection observed in nature is, typically, fast, so that the rate of convergence of the magnetic field lines is the fraction of the Alfven speed, v_A. The Sweet-Parker solution predicts reconnection rates which are negligible for the solar or astrophysical conditions, this have prompted research into collisionless reconnection. The stochasticity of magnetic field lines due to ambient turbulence leads to fast reconnection and the rate was predicted to be proportional to kinetic energy density of ambient turbulence. Also, tearing instability of the thin current sheet was proposed as a driver of resistivity-independent reconnection, which was shown to be consistent with two-dimensional simulati...

Beresnyak, Andrey

2013-01-01T23:59:59.000Z

450

Critical reaction rates in hypersonic combustion chemistry  

DOE Green Energy (OSTI)

High Mach number flight requires that the scramjet propulsion system operate at a relatively low static inlet pressure and a high inlet temperature. These two constraints can lead to extremely high temperatures in the combustor, yielding high densities of radical species and correspondingly poor chemical combustion efficiency. As the temperature drops in the nozzle expansion, recombination of these excess radicals can produce more product species, higher heat yield, and potentially more thrust. The extent to which the chemical efficiency can be enhanced in the nozzle expansion depends directly on the rate of the radical recombination reactions. A comprehensive assessment of the important chemical processes and an experimental validation of the critical rate parameters is therefore required if accurate predictions of scramjet performance are to be obtained. This report covers the identification of critical reactions, and the critical reaction rates in hypersonic combustion chemistry. 4 refs., 2 figs.

Oldenborg, R.C.; Harradine, D.M.; Loge, G.W.; Lyman, J.L.; Schott, G.L.; Winn, K.R.

1989-01-01T23:59:59.000Z

451

Analytical Improvements in PV Degradation Rate Determination  

DOE Green Energy (OSTI)

As photovoltaic (PV) penetration of the power grid increases, it becomes vital to know how decreased power output may affect cost over time. In order to predict power delivery, the decline or degradation rates must be determined accurately. For non-spectrally corrected data several complete seasonal cycles (typically 3-5 years) are required to obtain reasonably accurate degradation rates. In a rapidly evolving industry such a time span is often unacceptable and the need exists to determine degradation rates accurately in a shorter period of time. Occurrence of outliers and data shifts are two examples of analytical problems leading to greater uncertainty and therefore to longer observation times. In this paper we compare three methodologies of data analysis for robustness in the presence of outliers, data shifts and shorter measurement time periods.

Jordan, D. C.; Kurtz, S. R.

2011-02-01T23:59:59.000Z

452

Self-consistent microwave plasma heating rates  

SciTech Connect

Under conditions within a hot overdense plasma corona where the field frequency is much less than the electron plasma frequency and the field period is much less than the hydrodynamic expansion time it is shown that electron field reversal heating can exceed the combined classical heating rates due to inverse bremsstrahlung (skin effect) and field pressure (PdV) by a factor approximately v/ sub e//2v/sub i/ (half the ratio of electron and ion thermal velocities). In particular this rate can exceed the inertial expansion cooling rate at a collisionless corona density of approximately 1 percent solid core density and could be realized experimentally at core temperatures approximately 3--5 keV and microwave field intensities approximately 1 MG. (auth)

Ensley, D.L.; White, R.H.

1975-10-01T23:59:59.000Z

453

Intramolecular ET Rates in Modified Ferrocytochromes c  

NLE Websites -- All DOE Office Websites (Extended Search)

Intramolecular Electron-Transfer Rates on Driving Force, pH, Intramolecular Electron-Transfer Rates on Driving Force, pH, and Temperature in Ammineruthenium-Modified Ferrocytochromes c James F. Wishart, Ji Sun, Myung Cho, Chang Su, and Stephan S. Isied J. Phys. Chem. B 101, 687-693 (1997) [Find paper at ACS Publications] or use ACS Articles on Request Abstract: Several ruthenium ammine complexes were used to modify horse-heart cytochrome c at histidine-33, creating a series of (NH3)4(L)Ru-Cyt c derivatives (L = H2O/OH-, ammonia, 4-ethylpyridine, 3,5-lutidine, pyridine, isonicotinamide, N-methylpyrazinium) with a wide range of driving forces for Fe-to-Ru electron transfer (-DG° = -0.125 to +0.46 eV). Electron-transfer rates and activation parameters were measured by pulse radiolysis using azide or carbonate radicals. The driving-force dependence

454

RATES OF RETURN AND ALTERNATIVE MEASURES OF  

E-Print Network (OSTI)

We employ the EU KLEMS database to estimate the real rate of return to capital in 14 countries (11 in the EU, three outside the EU) in 10 branches of the market economy plus the market economy as a whole. Our measure of capital is an aggregate over seven types of asset: three ICT assets and four non-ICT assets. The real rate of return in the market economy does not vary very much across countries, the extremes being Spain (high) and Italy (low). The real rate appears to be trendless in most countries. Within each country however, the rate varies widely across the 10 branches, often being implausibly high or low. We also estimate the growth of capital services by two different methods: ex-post and ex-ante, and the contribution of capital to output growth by three methods: ex-post, ex-ante and hybrid. The ex-ante method uses an estimate of the required rate of return for each country instead of the actual, average rate of return to calculate user costs and also employs the expected growth of asset prices rather than the actual growth. These estimates are derived from exactly the same data as for the ex-post method, ie without any extraneous data being employed. For estimating the contribution of capital to output growth, the ex-ante method uses ex-ante profit as the weight, while both the ex-post and the hybrid method use ex-post profit. We find that the three methods produce very similar results at the market economy level. But differences are much larger at the branch level, particularly between the ex-post and ex-ante methods.

Nicholas Oulton; Ana Rincon-aznar

2009-01-01T23:59:59.000Z

455

Neutrino Event Rates from Gamma Ray Bursts  

E-Print Network (OSTI)

We recalculate the diffuse flux of high energy neutrinos produced by Gamma Ray Bursts (GRB) in the relativistic fireball model. Although we confirm that the average single burst produces only ~10^{-2} high energy neutrino events in a detector with 1 km^2 effective area, i.e. about 10 events per year, we show that the observed rate is dominated by burst-to-burst fluctuations which are very large. We find event rates that are expected to be larger by one order of magnitude, likely more, which are dominated by a few very bright bursts. This greatly simplifies their detection.

F. Halzen; D. W. Hooper

1999-08-12T23:59:59.000Z

456

Rating of Mixed Split Residential Air Conditioners  

E-Print Network (OSTI)

A methodology is presented for rating the performance of mixed, split residential air conditioners. The method accounts for the impact on system performance of the indoor evaporator, expansion device and fan; three major components that are likely to be substituted for the matched components in a mixed system. The method allows calculation of capacity at 95F rating point and seasonal energy efficiency ratio, SEER, without performing laboratory test of the complete system. Limitations of the procedure, present work, and anticipated improvements are also discussed.

Domanski, P. A.

1988-01-01T23:59:59.000Z

457

Large deviation properties of constant rate data streams sharing a buffer with variable rate cross traffic  

Science Conference Proceedings (OSTI)

We consider a constant rate data stream which shares a buffer with a variable rate data stream. A first come first serve service discipline is applied at the buffer. After service at the first buffer the variable rate traffic leaves the system, whereas ... Keywords: 68M20, 90B15, Markov-modulated fluid sources, fluid model, large buffer asymptotics, many sources asymptotics, on-off sources, primary 60F10, queueing network, secondary 60K25

Kurt Majewski

2008-10-01T23:59:59.000Z

458

Heart Physiology Lab Part 1: Pulse Rate  

E-Print Network (OSTI)

Heart Physiology Lab Part 1: Pulse Rate Measure your pulse in each of the following conditions (in in the class. You may use Table 1 in the Heart Physiology Worksheet for this, if you wish. Once you have all of the class averages for each measurement. You may use Graph 1 in the Heart Physiology Worksheet for this

Loughry, Jim

459

Higgs Boson Production Rates in Hadronic Collisions  

E-Print Network (OSTI)

Higgs boson production rates at hadron colliders are reviewed with particular emphasis on progress in the calculation of higher order QCD effects. Emphasis is placed on the uncertainties in the predictions for Higgs boson production. A firm understanding of these uncertainties is crucial for extracting new physics signals.

S. Dawson

2001-11-19T23:59:59.000Z

460

ON RATES OF CONVERGENCE FOR STOCHASTIC ...  

E-Print Network (OSTI)

Our focus is on rates of convergence of estimators of optimal solutions and ..... In preparation for that result, we state the following assumption, which is similar to ...... second problem is LandS, a modification of a simple problem in electrical...

Note: This page contains sample records for the topic "ah rated pack" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


461

Estimation of Mean Rain Rate through Censoring  

Science Conference Proceedings (OSTI)

A mixed lognormal distribution is fit to rain-rate data to estimate the spacetime average. To mitigate problems associated with biased data, data below a minimum and above a maximum threshold are treated as if they are at the respective ...

Donald Martin

1999-06-01T23:59:59.000Z

462

Radar Determination of Snowfall Rate and Accumulation  

Science Conference Proceedings (OSTI)

A unique method that provides for relating radar-measured reflectivity factors to snowfall rates at the ground is presented. Data were provided by a CPS-9, 3.2 cm radar from six 1978 Massachusetts snowstorms A best-fit power-law relationship ...

Roland J. Boucher; James G. Wieler

1985-01-01T23:59:59.000Z

463

The Distant Type Ia Supernova Rate  

DOE R&D Accomplishments (OSTI)

We present a measurement of the rate of distant Type Ia supernovae derived using 4 large subsets of data from the Supernova Cosmology Project. Within this fiducial sample, which surveyed about 12 square degrees, thirty-eight supernovae were detected at redshifts 0.25--0.85. In a spatially flat cosmological model consistent with the results obtained by the Supernova Cosmology Project, we derive a rest-frame Type Ia supernova rate at a mean red shift z {approx_equal} 0.55 of 1.53 {sub -0.25}{sub -0.31}{sup 0.28}{sup 0.32} x 10{sup -4} h{sup 3} Mpc{sup -3} yr{sup -1} or 0.58{sub -0.09}{sub -0.09}{sup +0.10}{sup +0.10} h{sup 2} SNu(1 SNu = 1 supernova per century per 10{sup 10} L{sub B}sun), where the first uncertainty is statistical and the second includes systematic effects. The dependence of the rate on the assumed cosmological parameters is studied and the redshift dependence of the rate per unit comoving volume is contrasted with local estimates in the context of possible cosmic star formation histories and progenitor models.

Pain, R.; Fabbro, S.; Sullivan, M.; Ellis, R. S.; Aldering, G.; Astier, P.; Deustua, S. E.; Fruchter, A. S.; Goldhaber, G.; Goobar, A.; Groom, D. E.; Hardin, D.; Hook, I. M.; Howell, D. A.; Irwin, M. J.; Kim, A. G.; Kim, M. Y.; Knop, R. A.; Lee, J. C.; Perlmutter, S.; Ruiz-Lapuente, P.; Schahmaneche, K.; Schaefer, B.; Walton, N. A.

2002-05-28T23:59:59.000Z

464

Radiative Heating Rates for Saharan Dust  

Science Conference Proceedings (OSTI)

A combined longwave and shortwave radiative transfer model was used to determine effects of Saharan dust on the radiative fluxes and heating/cooling rates in the atmosphere. Cases are treated for cloud-free and overcast conditions over the ocean ...

Toby N. Carlson; Stanley G. Benjamin

1980-01-01T23:59:59.000Z

465

Estimating the rate of web page updates  

Science Conference Proceedings (OSTI)

Estimating the rate of Web page updates helps in improving the Web crawler's scheduling policy. But, most of the Web sources are autonomous and updated independently. Clients like Web crawlers are not aware of when and how often the sources change. Unlike ...

Sanasam Ranbir Singh

2007-01-01T23:59:59.000Z

466

Investigation of determinism in heart rate variability  

Science Conference Proceedings (OSTI)

The article searches for the possible presence of determinism in heart rate variability (HRV) signals by using a new approach based on NARMA (nonlinear autoregressive moving average) modeling and free-run prediction. Thirty-three 256-point HRV time series obtained from Wistar rats submitted to different autonomic blockade protocols are considered

M. E. D. Gomes; A. V. P. Souza; H. N. Guimares; L. A. Aguirre

2000-01-01T23:59:59.000Z

467

Electrochemical and rate performance study of high-voltage lithium-richcomposition: Li1.2Mn0.525Ni0.175Co0.1O2  

Science Conference Proceedings (OSTI)

We report electrochemical studies of high voltage cathodes composed of lithium rich layeredlayered material having the nominal composition Li1.2Mn0.525Ni0.175Co0.1O2, or equivalently 0.6Li[Li1/3Mn2/3]O2 0.4Li[Mn0.3Ni0.45Co0.25]O2. These aspects were investigated by cyclic voltammetry studies in conjunction with electrochemical impedance spectroscopy measurements to understand the redox reactions involving multiple transition metals and their capacity contribution at higher voltages, up to 4.9 V. Further, cathodes with 1.5 wt.% carbon nanofibers added to the Li1.2Mn0.525Ni0.175Co0.1O2 composite electrode showed stable reversible capacities of about 280 mAh g 1 when cycled to 4.9 V for more than 100 cycles, and almost a factor of two improvements in the rate performance compared to the electrode composition prepared using conventional composition (7.5% carbon black and 7.5% binder).

Martha, Surendra K [ORNL; Nanda, Jagjit [ORNL; Veith, Gabriel M [ORNL; Dudney, Nancy J [ORNL

2012-01-01T23:59:59.000Z

468

A New Series of Rate Decline Relations Based on the Diagnosis of Rate-Time Data  

E-Print Network (OSTI)

The so-called "Arps" rate decline relations are by far the most widely used tool for assessing oil and gas reserves from rate performance. These relations (i.e., the exponential and hyperbolic decline relations) are empirical where the starting point for their derivation is given by the definitions of the "loss ratio" and the "derivative of the loss ratio", where the "loss ratio" is the ratio of rate data to derivative of rate data, and the "derivative of the loss ratio" is the "b-parameter" as defined by Arps [1945]. The primary goal of this work is the interpretation of the b-parameter continuously over time and thus the better understanding of its character. As is shown below we propose "monotonically decreasing functional forms" for the characterization of the b-parameter, in addition to the exponential and hyperbolic rate decline relations, where the b-parameter is assumed to be zero and constant, respectively. The proposed equations are as follow: b(t)=constant (Arps' hyperbolic rate-decline relation), []tbbtb10exp)(-bt= (exponential function), (power-law function), 10)(btbtb=)/(1)(10tbbtb+= (rational function). The corresponding rate decline relation for each case is obtained by solving the differential equation associated with the selected functional for the b-parameter. The next step of this procedure is to test and validate each of the rate decline relations by applying them to various numerical simulation cases (for gas), as well as for field data cases obtained from tight/shale gas reservoirs. Our results indicate that b-parameter is never constant but it changes continuously with time. The ultimate objective of this work is to establish each model as a potential analysis/diagnostic relation. Most of the proposed models yield more realistic estimations of gas reserves in comparison to the traditional Arps' rate decline relations (i.e., the hyperbolic decline) where the reserves estimates are inconsistent and over-estimated. As an example, the rational b-parameter model seems to be the most accurate model in terms of representing the character of rate data; and therefore, should yield more realistic reserves estimates. Illustrative examples are provided for better understanding of each b-parameter rate decline model. The proposed family of rate decline relations was based on the character of the b-parameter computed from the rate-time data and they can be applied to a wide range of data sets, as dictated by the character of rate data.

Boulis, Anastasios

2009-08-01T23:59:59.000Z

469

Rate Us - ORNL DAAC Feedback Forum  

NLE Websites -- All DOE Office Websites (Extended Search)

Help > Feedback Help > Feedback Rate Us - ORNL DAAC Feedback Forum To improve service to our customers, this forum provides a means to monitor user satisfaction. Please take a moment to tell us about your experience. Consider Data availability, accessibility, and value Web navigation and content Customer service Your responses will remain anonymous in keeping with our Privacy Policy. Select one of the following options that best describes your experience with the ORNL DAAC. Positive Mixed Negative If you wish to add comments or to explain your rating, please enter your comments in the box below. If you would like us to reply to your comments or concern, please enter your e-mail address here: Please solve the following simple math problem: 4 x 2 = help icon Submit Feedback Clear form

470

Thermal dilepton rates from quenched lattice QCD  

E-Print Network (OSTI)

We present new lattice results on the continuum extrapolation of the vector current correlation function. Lattice calculations have been carried out in the deconfined phase at a temperature of 1.1 Tc, extending our previous results at 1.45 Tc, utilizing quenched non-perturbatively clover-improved Wilson fermions and light quark masses. A systematic analysis on multiple lattice spacings allows to perform the continuum limit of the correlation function and to extract spectral properties in the continuum limit. Our current analysis suggests the results for the electrical conductivity are proportional to the temperature and the thermal dilepton rates in the quark gluon plasma are comparable for both temperatures. Preliminary results of the continuum extrapolated correlation function at finite momenta, which relates to thermal photon rates, are also presented.

H. -T. Ding; A. Francis; O. Kaczmarek; F. Karsch; E. Laermann; S. Mukherjee; M. Mller; W. Soeldner

2013-01-30T23:59:59.000Z

471

Stretch rate of tubular premixed flames  

Science Conference Proceedings (OSTI)

Following Seshadri and Williams solution describing the flow field for the opposed jet burner, the analytical solution is given for the flow field of two other burners: the opposed tubular burner and the tubular burner. Under plug flow boundary conditions, it is shown that the stretch rate at the stagnation surface of the opposed tubular burner is k=pV/(R{sub 2}-R{sub 1}) for the case of equal velocities and equal densities (i.e., r{sub 1}=r{sub 2} and V{sub 1}=-V{sub 2}=V). For the tubular burner, the stretch rate at the center of the burner is k=pV/R{sub 2}. The comparison of the numerical simulation and analytical solution is carried out to verify the analytical solution. (author)

Wang, Peiyong; Wehrmeyer, Joseph A.; Pitz, Robert W. [Mechanical Engineering Department, Vanderbilt University, Nashville, TN 37235 (United States)

2006-04-15T23:59:59.000Z

472

Subsurface heaters with low sulfidation rates  

SciTech Connect

A system for heating a hydrocarbon containing formation includes a heater having an elongated ferromagnetic metal heater section. The heater is located in an opening in a formation. The heater section is configured to heat the hydrocarbon containing formation. The exposed ferromagnetic metal has a sulfidation rate that goes down with increasing temperature of the heater, when the heater is in a selected temperature range.

John, Randy Carl; Vinegar, Harold J

2013-12-10T23:59:59.000Z

473

Decoherence rates for Galilean covariant dynamics  

E-Print Network (OSTI)

We introduce a measure of decoherence for a class of density operators. For Gaussian density operators in dimension one it coincides with an index used by Morikawa (1990). Spatial decoherence rates are derived for three large classes of the Galilean covariant quantum semigroups introduced by Holevo. We also characterize the relaxation to a Gaussian state for these dynamics and give a theorem for the convergence of the Wigner function to the probability distribution of the classical analog of the process.

Jeremy Clark

2007-10-08T23:59:59.000Z

474

Heating Rate Profiles in Galaxy Clusters  

E-Print Network (OSTI)

In recent years evidence has accumulated suggesting that the gas in galaxy clusters is heated by non-gravitational processes. Here we calculate the heating rates required to maintain a physically motived mass flow rate, in a sample of seven galaxy clusters. We employ the spectroscopic mass deposition rates as an observational input along with temperature and density data for each cluster. On energetic grounds we find that thermal conduction could provide the necessary heating for A2199, Perseus, A1795 and A478. However, the suppression factor, of the clasical Spitzer value, is a different function of radius for each cluster. Based on the observations of plasma bubbles we also calculate the duty cycles for each AGN, in the absence of thermal conduction, which can provide the required energy input. With the exception of Hydra-A it appears that each of the other AGNs in our sample require duty cycles of roughly $10^{6}-10^{7}$ yrs to provide their steady-state heating requirements. If these duty cycles are unrealistic, this may imply that many galaxy clusters must be heated by very powerful Hydra-A type events interspersed between more frequent smaller-scale outbursts. The suppression factors for the thermal conductivity required for combined heating by AGN and thermal conduction are generally acceptable. However, these suppression factors still require `fine-tuning` of the thermal conductivity as a function of radius. As a consequence of this work we present the AGN duty cycle as a cooling flow diagnostic.

Edward C. D. Pope; Georgi Pavlovski; Christian R. Kaiser; Hans Fangohr

2006-01-05T23:59:59.000Z

475

Category:Utility Rates | Open Energy Information  

Open Energy Info (EERE)

source source History View New Pages Recent Changes All Special Pages Semantic Search/Querying Get Involved Help Apps Datasets Community Login | Sign Up Search Category Edit History Facebook icon Twitter icon » Category:Utility Rates Jump to: navigation, search Add a new Utility Rate Pages in category "Utility Rates" The following 200 pages are in this category, out of 42,539 total. (previous 200) (next 200) 0 Data:0000827d-84d0-453d-b659-b86869323897 Data:000086db-7a5e-4356-9c57-c912f7d1622e Data:0003a8b3-04b9-4ecb-b06d-6022e7f0f009 Data:000470c7-df04-47aa-bdd2-d70f0a2c52b3 Data:000b6dfa-a541-428a-9029-423006e22a34 Data:000db36e-b548-43e7-a283-d37ecc77cef1 Data:000e60f7-120d-48ab-a1f9-9c195329c628 Data:00101108-073b-4503-9cd4-01769611c26f Data:001361ca-50d2-49bc-b331-08755a2c7c7d

476

Dependency and false discovery rate: Asymptotics  

E-Print Network (OSTI)

Some effort has been undertaken over the last decade to provide conditions for the control of the false discovery rate by the linear step-up procedure (LSU) for testing $n$ hypotheses when test statistics are dependent. In this paper we investigate the expected error rate (EER) and the false discovery rate (FDR) in some extreme parameter configurations when $n$ tends to infinity for test statistics being exchangeable under null hypotheses. All results are derived in terms of $p$-values. In a general setup we present a series of results concerning the interrelation of Simes' rejection curve and the (limiting) empirical distribution function of the $p$-values. Main objects under investigation are largest (limiting) crossing points between these functions, which play a key role in deriving explicit formulas for EER and FDR. As specific examples we investigate equi-correlated normal and $t$-variables in more detail and compute the limiting EER and FDR theoretically and numerically. A surprising limit behavior occ...

Finner, Helmut; Roters, Markus

2007-01-01T23:59:59.000Z

477

Neutrino energy loss rates and positron capture rates on $^{55}$Co for presupernova and supernova physics  

E-Print Network (OSTI)

Proton-neutron quasi-particle random phase approximation (pn-QRPA) theory has recently being used for calculation of stellar weak interaction rates of $fp$-shell nuclide with success. Neutrino losses from proto-neutron stars play a pivotal role to decide if these stars would be crushed into black holes or explode as supernovae. The product of abundance and positron capture rates on $^{55}$Co is substantial and as such can play a role in fine tuning of input parameters of simulation codes specially in the presupernova evolution. Recently we introduced our calculation of capture rates on $^{55}$Co, in a luxurious model space of $7 \\hbar \\omega$, employing the pn-QRPA theory with a separable interaction. Simulators, however, may require these rates on a fine scale. Here we present for the first time an expanded calculation of the neutrino energy loss rates and positron capture rates on $^{55}$Co on an extensive temperature-density scale. These type of scale is appropriate for interpolation purposes and of greater utility for simulation codes. The pn-QRPA calculated neutrino energy loss rates are enhanced roughly up to two orders of magnitude compared with the large-scale shell model calculations and favor a lower entropy for the core of massive stars.

Jameel-Un Nabi; Muhammad Sajjad

2011-08-03T23:59:59.000Z

478

Liability aspects of home energy-rating systems  

SciTech Connect

Liability aspects of home energy rating systems are discussed. An introduction to the rating system concept, including types of rating systems, implementation efforts to date, and possible groups to conduct ratings, is also included. The home energy rating system concept involves the periodic rating of the energy efficiency of residential buildings. The rating can provide a relative indication of a home's energy efficiency and also a quantitative estimate of consumption, fuel cost, or both. Primary attention is given to liability issues associated with developing and performing ratings. Secondary attention is given to possible liability associated with misuse of a rating once it has been performed.

Hendrickson, P.L.

1983-10-01T23:59:59.000Z

479

Occurrence rate of extreme magnetic storms  

E-Print Network (OSTI)

Statistical analysis of occurrence rate of magnetic storms induced by different types of interplanetary drivers is made on the basis of OMNI data for period 1976-2000. Using our catalog of large scale types of solar wind streams we study storms induced by interplanetary coronal mass ejections (ICME) (separately magnetic clouds (MC) and Ejecta) and both types of compressed regions: corotating interaction regions (CIR) and Sheaths. For these types of drivers we calculate integral probabilities of storms with minimum Dst storms shows that such a magnetic storm as Carrington storm in 1859 with Dst = -1760 nT is observed on the Earth with frequency 1 event during ~500 year.

Yermolaev, Yu I; Nikolaeva, N S; Yermolaev, M Yu

2013-01-01T23:59:59.000Z

480

Relevant energy ranges for astrophysical reaction rates  

Science Conference Proceedings (OSTI)

Effective energy windows (Gamow windows) of astrophysical reaction rates for (p,gamma), (p,n), (p,alpha), (alpha,gamma), (alpha,n), (alpha,p), (n,gamma), (n,p), and (n,alpha) on targets with 10<=Z<=83 from proton to neutron dripline are calculated using theoretical cross sections. It is shown that widely used approximation formulas for the relevant energy ranges are not valid for a large number of reactions relevant to hydrostatic and explosive nucleosynthesis. The influence of the energy dependence of the averaged widths on the location of the Gamow windows is discussed and the results are presented in tabular form.

Rauscher, Thomas [Department of Physics, University of Basel, Klingelbergstr. 82, CH-4056 Basel (Switzerland)

2010-04-15T23:59:59.000Z

Note: This page contains sample records for the topic "ah rated pack" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


481

Reverse Engineering of Proteasomal Translocation Rates  

E-Print Network (OSTI)

We address the problem of proteasomal protein translocation and introduce a new stochastic model of the proteasomal digestion (cleavage) of proteins. In this model we account for the protein translocation and the positioning of cleavage sites of a proteasome from first principles. We show by test examples and by processing experimental data that our model allows reconstruction of the translocation and cleavage rates from mass spectroscopy data on digestion patterns and can be used to investigate the properties of transport in different experimental set-ups. Detailed investigation with this model will enable theoretical quantitative prediction of the proteasomal activity.

D. S. Goldobin; M. Mishto; K. Textoris-Taube; P. M. Kloetzel; A. Zaikin

2008-04-04T23:59:59.000Z

482

Estimating meteor rates using Bayesian inference  

E-Print Network (OSTI)

A method for estimating the true meteor rate \\lambda\\ from a small number of observed meteors n is derived. We employ Bayesian inference with a Poissonian likelihood function. We discuss the choice of a suitable prior and propose the adoption of Jeffreys prior, P(\\lambda)=\\lambda^{-0.5}, which yields an expectation value E(\\lambda) = n+0.5 for any n \\geq 0. We update the ZHR meteor activity formula accordingly, and explain how 68%- and 95%-confidence intervals can be computed.

Barentsen, Geert; Frhlich, Hans-Erich

2011-01-01T23:59:59.000Z

483

Corrosion Rate, Effect of Soil Properties: Development of a Sensor System to Calculate Corrosion Rates  

Science Conference Proceedings (OSTI)

This report addresses corrosion of substation ground grids and the development of a corrosion sensor system and supporting algorithms that can be used in the field to quickly estimate the corrosion rate of a metal in soils of low resistivity.The system is based on the linear polarization resistance (LPR) technique, an electrochemical method of calculating corrosion rates by measuring the relationship between electrochemical potential and the electric current between electrodes. ...

2013-12-16T23:59:59.000Z

484

HTR-PROTEUS PEBBLE BED EXPERIMENTAL PROGRAM CORES 9 & 10: COLUMNAR HEXAGONAL POINT-ON-POINT PACKING WITH A 1:1 MODERATOR-TO-FUEL PEBBLE RATIO  

SciTech Connect

PROTEUS is a zero-power research reactor based on a cylindrical graphite annulus with a central cylindrical cavity. The graphite annulus remains basically the same for all experimental programs, but the contents of the central cavity are changed according to the type of reactor being investigated. Through most of its service history, PROTEUS has represented light-water reactors, but from 1992 to 1996 PROTEUS was configured as a pebble-bed reactor (PBR) critical facility and designated as HTR-PROTEUS. The nomenclature was used to indicate that this series consisted of High Temperature Reactor experiments performed in the PROTEUS assembly. During this period, seventeen critical configurations were assembled and various reactor physics experiments were conducted. These experiments included measurements of criticality, differential and integral control rod and safety rod worths, kinetics, reaction rates, water ingress effects, and small sample reactivity effects (Ref. 3). HTR-PROTEUS was constructed, and the experimental program was conducted, for the purpose of providing experimental benchmark data for assessment of reactor physics computer codes. Considerable effort was devoted to benchmark calculations as a part of the HTR-PROTEUS program. References 1 and 2 provide detailed data for use in constructing models for codes to be assessed. Reference 3 is a comprehensive summary of the HTR-PROTEUS experiments and the associated benchmark program. This document draws freely from these references. Only Cores 9 and 10 are evaluated in this benchmark report due to similarities in their construction. The other core configurations of the HTR-PROTEUS program are evaluated in their respective reports as outlined in Section 1.0. Cores 9 and 10 were evaluated and determined to be acceptable benchmark experiments.

John D. Bess

2013-03-01T23:59:59.000Z

485

Provo River Project Power Sales Rate History  

NLE Websites -- All DOE Office Websites (Extended Search)

Provo River Project Power Sales Rate History Updated: 12/20/2013 Rate Schedule Effective Dates Energy (Mills/kWh) Capacity ($/kW-mo.) Combined (Mills/kWh) Administrative Action 4/58 - 6/64 (Summer Season) 3.000 N.A. N.A. Administrative Action 10/58 - 4/64 (Winter Season) 4.500 N.A. N.A. Administrative Action 7/64 - 9/79 (Summer Season) 5.000 N.A. N.A. Administrative Action 10/64 - 9/79 (Winter Season) 3.000 N.A. N.A. Administrative Action 10/79 - 9/82 6.000 N.A. N.A. Administrative Action 10/82 - 9/90 6.850 N.A. N.A. Administrative Action 10/90 - 9/94 8.000 N.A. N.A. Administrative Action 10/94 - Present Installments N.A. N.A. Note: The Provo River Project sells energy only. As of October 1994, customers pay all OM&R expenses and in return, receive all the energy produced by the Project.

486

Coincident count rates in absorbing dielectric media  

E-Print Network (OSTI)

A study of the effects of absorption on the nonlinear process of parametric down conversion is presented. Absorption within the nonlinear medium is accounted for by employing the framework of macroscopic QED and the Green tensor quantization of the electromagnetic field. An effective interaction Hamiltonian, which describes the nonlinear interaction of the electric field and the linear noise polarization field, is used to derive the quantum state of the light leaving a nonlinear crystal. The signal and idler modes of this quantum state are found to be a superpositions of the electric and noise polarization fields. Using this state, the expression for the coincident count rates for both Type I and Type II conversion are found. The nonlinear interaction with the noise polarization field were shown to cause