Sample records for age refining air

  1. Preliminary assessment of future refining impacts of the Clean Air Act Amendments of 1990

    SciTech Connect (OSTI)

    Hadder, G.R.

    1991-09-01T23:59:59.000Z

    A preliminary assessment of the future refining impacts of the Clean Air Act Amendments of 1990 has been performed with the Navy Mobility Fuels Forecasting Systems. The assessment suggests that gasoline reformulation costs in domestic coastal and near-coastal refining regions in the year 2000 could be 3.5 to 5.6 cents per gallon (in terms of 1989 currency). For heating value equivalent to one gallon of conventional gasoline, the regional total added costs (including reformulation costs) for reformulated gasoline could be 5.9 to 8.0 cents. In blending reformulated gasolines, the reduction of butane for lower Reid vapor pressure and the reduction of reformate for lower aromatics are generally compensated by increased percentages of alkylate and/or straight run naphthas. Relatively larger refinery process capacity additions are required for butane isomerization, alkylation, aromatics recovery, and distillate hydrotreating. 21 refs., 3 figs., 18 tabs.

  2. Optimal Supply Angle of Upside Air Supply in Manned Spacecraft Cabin-Based Air Age

    E-Print Network [OSTI]

    Liang, Z.; Zhang, J.; Lu, Y.

    2006-01-01T23:59:59.000Z

    The age of air in the workaround of a manned spacecraft cabin that contain astronauts, apparatus and simple living establishments was numerically simulated by use of commercial software and a standard k-e turbulence model. An air inlet installed...

  3. The potential impact of proposed hazardous air pollutant legislation on the US refining industry. Final report, Task 9

    SciTech Connect (OSTI)

    Not Available

    1989-11-01T23:59:59.000Z

    The Administration has recently submitted a Clean Air Act Bill to Congress which would significantly modify the regulatory treatment of industrial hazardous air pollutants (air toxics). The adverse economic impacts of this legislation on the petroleum refining industry could be substantial. Depending on how EPA interprets the legislative language, the capital costs of compliance for the proposed bill could range from $1.3 to $15.0 billion. At the upper end of the range, costs of this order of magnitude would be over 2.5 times larger than the combined estimated cost of EPAs gasoline volatility (RVP) regulations and the proposed diesel sulfur content regulations. Potential compliance costs could be as much as $0.40 per barrel processed for large, complex refineries and as much as $0.50 per barrel for some small, simple refineries. For perspective, total refining costs, including a normal return on investment, are $4--5 per barrel. Because foreign refineries supplying the US will not be affected by the US air toxics regulations, US refineries may not be able to raise prices sufficiently to recover their compliance costs. For this reason, the air toxic legislation may put US refineries at an economic disadvantage relative to foreign competitors. Even under the best petroleum product market conditions, costs of $0.40 to $0.50 per barrel processed could reduce US Gulf refiner cash operating margins by as much as 29 percent. Under less favorable market conditions, such as the mid-80`s when refiners were losing money, the hazardous air pollutant regulations could greatly increase US refiner operating losses and potentially lead to closure of some marginal refineries.

  4. Tropospheric SF6: Age of air from the Northern Hemisphere midlatitude surface

    E-Print Network [OSTI]

    Waugh, Darryn W.

    Tropospheric SF6: Age of air from the Northern Hemisphere midlatitude surface D. W. Waugh,1 A. M 2013. [1] Observations of SF6 are used to quantify the mean time since air was in ("mean age" from. Comparisons of simulated SF6 and an idealized clock tracer confirm that the time lag between the SF6 mixing

  5. Firing of pulverized solvent refined coal

    DOE Patents [OSTI]

    Derbidge, T. Craig (Sunnyvale, CA); Mulholland, James A. (Chapel Hill, NC); Foster, Edward P. (Macungie, PA)

    1986-01-01T23:59:59.000Z

    An air-purged burner for the firing of pulverized solvent refined coal is constructed and operated such that the solvent refined coal can be fired without the coking thereof on the burner components. The air-purged burner is designed for the firing of pulverized solvent refined coal in a tangentially fired boiler.

  6. Rietveld Refinement

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Obtain from refinement of calibrant (eg. LaB 6 ) Gives the initial values for the profile function (instrumental only parameters) Add screenshot for previous slide on...

  7. Firing of pulverized solvent refined coal

    DOE Patents [OSTI]

    Lennon, Dennis R. (Allentown, PA); Snedden, Richard B. (McKeesport, PA); Foster, Edward P. (Macungie, PA); Bellas, George T. (Library, PA)

    1990-05-15T23:59:59.000Z

    A burner for the firing of pulverized solvent refined coal is constructed and operated such that the solvent refined coal can be fired successfully without any performance limitations and without the coking of the solvent refined coal on the burner components. The burner is provided with a tangential inlet of primary air and pulverized fuel, a vaned diffusion swirler for the mixture of primary air and fuel, a center water-cooled conical diffuser shielding the incoming fuel from the heat radiation from the flame and deflecting the primary air and fuel steam into the secondary air, and a watercooled annulus located between the primary air and secondary air flows.

  8. Studies of asphalt air blowing and development of a new short-term aging technique

    E-Print Network [OSTI]

    Vassiliev, Nicolai

    2001-01-01T23:59:59.000Z

    , Table m-2. Low temperature hardening properi. ies of air blown asphalt fractions and blends. Table III-3. Parent asphalt HS, oxidation rate, and HR . Table IV-1. Estimated time required to achieve same degrcc of aging as RTFOT for Exxon AC-10 films... of varying I. hickness . 70 Table IV-2 Effect of air blowing conditions for Exxon AC- I 0, 325 'F, 70 min. 70 Table IV-3. Condensed volatiles and RTFOT mass change . 80 Table IV-4. Reproducibility analysis. LIST OF FIGURES P ige Figure I-l. Thin film...

  9. Studies of asphalt air blowing and development of a new short-term aging technique 

    E-Print Network [OSTI]

    Vassiliev, Nicolai

    2001-01-01T23:59:59.000Z

    lower temperature variation in the oil bath and better film agitation in the flask. At 163 'C (325 'F) for a sample weight of 200 g it takes 160 minutes to achieve the aging effect closest to that of the TFOT and 210 minutes to compare... on the operating temperature and was less at higher temperatures. A total of 300 g of heated material was placed in a 1 qt (07946 Ll can and air-blown with constant agitation by a mixer attached to a motor at 1550 RPM. An insulated heating tape was used to heat...

  10. On Adaptive Mesh Refinement for Atmospheric Pollution Models

    E-Print Network [OSTI]

    Sandu, Adrian

    On Adaptive Mesh Refinement for Atmospheric Pollution Models Emil M. Constantinescu and Adrian res- olution system for modeling regional air pollution based on the chemical transport model STEM. Keywords: Air Pollution Modeling, Adaptive Mesh Refinement. 1 Introduction Inadequate grid resolution can

  11. ITP Petroleum Refining: Profile of the Petroleum Refining Industry...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Profile of the Petroleum Refining Industry in California: California Industries of the Future Program ITP Petroleum Refining: Profile of the Petroleum Refining Industry in...

  12. ITP Petroleum Refining: Energy Bandwidth for Petroleum Refining...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Bandwidth for Petroleum Refining Processes ITP Petroleum Refining: Energy Bandwidth for Petroleum Refining Processes bandwidth.pdf More Documents & Publications ITP Petroleum...

  13. An independent refiners approach to RFG

    SciTech Connect (OSTI)

    Czeskleba, M.

    1994-12-31T23:59:59.000Z

    This report was presented by Mike Czeskleba,Senior Business Analyst for Ashland Petroleum Company in Ashland, Kentucky. Ashland is one of the largest independent refiners and a leading marketer of gasoline and other petroleum products in the U.S. The issues addressed in this report concern the use of ethanol as a gasoline extender and renewable oxygenate, and its use in Reformulated Gasolines (RFG). The impact of Clean Air Act requirements for 1995 and beyond on petroleum refiners and producers is discussed. Some of the strategies which Ashland Petroleum Company is using to meet regulation requirements is also presented.

  14. Refinement Modal Logic

    E-Print Network [OSTI]

    Bozzelli, Laura; French, Tim; Hales, James; Pinchinat, Sophie

    2012-01-01T23:59:59.000Z

    In this paper we present refinement modal logic. A refinement is like a bisimulation, except that from the three relational requirements only 'atoms' and 'back' need to be satisfied. Our logic contains a new operator 'forall' in additional to the standard modalities 'Box' for each agent. The operator 'forall' acts as a quantifier over the set of all refinements of a given model. We call it the refinement operator. As a variation on a bisimulation quantifier, it can be seen as a refinement quantifier over a variable not occurring in the formula bound by the operator. The logic combines the simplicity of multi-agent modal logic with some powers of monadic second order quantification. We present a sound and complete axiomatization of multiagent refinement modal logic. We also present an extension of the logic to the modal mu-calculus, and an axiomatization for the single-agent version of this logic. Examples and applications are also discussed: to software verification and design (the set of agents can also be s...

  15. Refiners get petchems help

    SciTech Connect (OSTI)

    Wood, A.; Cornitius, T.

    1997-06-11T23:59:59.000Z

    The U.S.Refining Industry is facing hard times. Slow growth, tough environmental regulations, and fierce competition - especially in retail gasoline - have squeezed margins and prompted a series of mergers and acquisitions. The trend has affected the smallest and largest players, and a series of transactions over the past two years has created a new industry lineup. Among the larger companies, Mobil and Amoco are the latest to consider a refining merger. That follows recent plans by Ashland and Marathon to merge their refining businesses, and the decision by Shell, Texaco, and Saudi Aramco to combine some U.S. operations. Many of the leading independent refiners have increased their scale by acquiring refinery capacity. With refining still in the doldrums, more independents are taking a closer look at boosting production of petrochemicals, which offer high growth and, usually, better margins. That is being helped by the shift to refinery processes that favor the increased production of light olefins for alkylation and the removal of aromatics, providing opportunity to extract these materials for the petrochemical market. 5 figs., 3 tabs.

  16. Issues in adaptive mesh refinement

    SciTech Connect (OSTI)

    Dai, William Wenlong [Los Alamos National Laboratory

    2009-01-01T23:59:59.000Z

    In this paper, we present an approach for a patch-based adaptive mesh refinement (AMR) for multi-physics simulations. The approach consists of clustering, symmetry preserving, mesh continuity, flux correction, communications, and management of patches. Among the special features of this patch-based AMR are symmetry preserving, efficiency of refinement, special implementation offlux correction, and patch management in parallel computing environments. Here, higher efficiency of refinement means less unnecessarily refined cells for a given set of cells to be refined. To demonstrate the capability of the AMR framework, hydrodynamics simulations with many levels of refinement are shown in both two- and three-dimensions.

  17. Towards automated crystallographic structure refinement with phenix.refine

    SciTech Connect (OSTI)

    Afonine, Pavel V., E-mail: pafonine@lbl.gov; Grosse-Kunstleve, Ralf W.; Echols, Nathaniel; Headd, Jeffrey J.; Moriarty, Nigel W. [Lawrence Berkeley National Laboratory, One Cyclotron Road, MS64R0121, Berkeley, CA 94720 (United States); Mustyakimov, Marat; Terwilliger, Thomas C. [Los Alamos National Laboratory, M888, Los Alamos, NM 87545 (United States); Urzhumtsev, Alexandre [CNRS–INSERM–UdS, 1 Rue Laurent Fries, BP 10142, 67404 Illkirch (France); Université Henri Poincaré, Nancy 1, BP 239, 54506 Vandoeuvre-lès-Nancy (France); Zwart, Peter H. [Lawrence Berkeley National Laboratory, One Cyclotron Road, MS64R0121, Berkeley, CA 94720 (United States); Adams, Paul D. [Lawrence Berkeley National Laboratory, One Cyclotron Road, MS64R0121, Berkeley, CA 94720 (United States); University of California Berkeley, Berkeley, CA 94720 (United States)

    2012-04-01T23:59:59.000Z

    phenix.refine is a program within the PHENIX package that supports crystallographic structure refinement against experimental data with a wide range of upper resolution limits using a large repertoire of model parameterizations. This paper presents an overview of the major phenix.refine features, with extensive literature references for readers interested in more detailed discussions of the methods. phenix.refine is a program within the PHENIX package that supports crystallographic structure refinement against experimental data with a wide range of upper resolution limits using a large repertoire of model parameterizations. It has several automation features and is also highly flexible. Several hundred parameters enable extensive customizations for complex use cases. Multiple user-defined refinement strategies can be applied to specific parts of the model in a single refinement run. An intuitive graphical user interface is available to guide novice users and to assist advanced users in managing refinement projects. X-ray or neutron diffraction data can be used separately or jointly in refinement. phenix.refine is tightly integrated into the PHENIX suite, where it serves as a critical component in automated model building, final structure refinement, structure validation and deposition to the wwPDB. This paper presents an overview of the major phenix.refine features, with extensive literature references for readers interested in more detailed discussions of the methods.

  18. A Theory of Program Refinement 

    E-Print Network [OSTI]

    Denney, Ewen WKC

    We give a canonical program refinement calculus based on the lambda calculus and classical first-order predicate logic, and study its proof theory and semantics. The intention is to construct a metalanguage for refinement in which basic principles...

  19. Minimally refined biomass fuel

    DOE Patents [OSTI]

    Pearson, Richard K. (Pleasanton, CA); Hirschfeld, Tomas B. (Livermore, CA)

    1984-01-01T23:59:59.000Z

    A minimally refined fluid composition, suitable as a fuel mixture and derived from biomass material, is comprised of one or more water-soluble carbohydrates such as sucrose, one or more alcohols having less than four carbons, and water. The carbohydrate provides the fuel source; water solubilizes the carbohydrates; and the alcohol aids in the combustion of the carbohydrate and reduces the vicosity of the carbohydrate/water solution. Because less energy is required to obtain the carbohydrate from the raw biomass than alcohol, an overall energy savings is realized compared to fuels employing alcohol as the primary fuel.

  20. Refines Efficiency Improvement

    SciTech Connect (OSTI)

    WRI

    2002-05-15T23:59:59.000Z

    Refinery processes that convert heavy oils to lighter distillate fuels require heating for distillation, hydrogen addition or carbon rejection (coking). Efficiency is limited by the formation of insoluble carbon-rich coke deposits. Heat exchangers and other refinery units must be shut down for mechanical coke removal, resulting in a significant loss of output and revenue. When a residuum is heated above the temperature at which pyrolysis occurs (340 C, 650 F), there is typically an induction period before coke formation begins (Magaril and Aksenova 1968, Wiehe 1993). To avoid fouling, refiners often stop heating a residuum before coke formation begins, using arbitrary criteria. In many cases, this heating is stopped sooner than need be, resulting in less than maximum product yield. Western Research Institute (WRI) has developed innovative Coking Index concepts (patent pending) which can be used for process control by refiners to heat residua to the threshold, but not beyond the point at which coke formation begins when petroleum residua materials are heated at pyrolysis temperatures (Schabron et al. 2001). The development of this universal predictor solves a long standing problem in petroleum refining. These Coking Indexes have great potential value in improving the efficiency of distillation processes. The Coking Indexes were found to apply to residua in a universal manner, and the theoretical basis for the indexes has been established (Schabron et al. 2001a, 2001b, 2001c). For the first time, a few simple measurements indicates how close undesired coke formation is on the coke formation induction time line. The Coking Indexes can lead to new process controls that can improve refinery distillation efficiency by several percentage points. Petroleum residua consist of an ordered continuum of solvated polar materials usually referred to as asphaltenes dispersed in a lower polarity solvent phase held together by intermediate polarity materials usually referred to as resins. The Coking Indexes focus on the amount of these intermediate polarity species since coke formation begins when these are depleted. Currently the Coking Indexes are determined by either titration or solubility measurements which must be performed in a laboratory. In the current work, various spectral, microscopic, and thermal techniques possibly leading to on-line analysis were explored for measuring the Coking Indexes.

  1. Crystal structure refinement with SHELXL

    SciTech Connect (OSTI)

    Sheldrick, George M., E-mail: gsheldr@shelx.uni-ac.gwdg.de [Department of Structural Chemistry, Georg-August Universität Göttingen, Tammannstraße 4, Göttingen 37077 (Germany)

    2015-01-01T23:59:59.000Z

    New features added to the refinement program SHELXL since 2008 are described and explained. The improvements in the crystal structure refinement program SHELXL have been closely coupled with the development and increasing importance of the CIF (Crystallographic Information Framework) format for validating and archiving crystal structures. An important simplification is that now only one file in CIF format (for convenience, referred to simply as ‘a CIF’) containing embedded reflection data and SHELXL instructions is needed for a complete structure archive; the program SHREDCIF can be used to extract the .hkl and .ins files required for further refinement with SHELXL. Recent developments in SHELXL facilitate refinement against neutron diffraction data, the treatment of H atoms, the determination of absolute structure, the input of partial structure factors and the refinement of twinned and disordered structures. SHELXL is available free to academics for the Windows, Linux and Mac OS X operating systems, and is particularly suitable for multiple-core processors.

  2. ITP Petroleum Refining: Energy and Environmental Profile of the...

    Energy Savers [EERE]

    Energy Bandwidth for Petroleum Refining Processes ITP Petroleum Refining: Technology Roadmap for the Petroleum Industry ITP Petroleum Refining: Profile of the Petroleum Refining...

  3. US refiners choose variety of routes to MTBE

    SciTech Connect (OSTI)

    Rhodes, A.K.

    1992-09-07T23:59:59.000Z

    This paper reports that refiners and merchant manufacturers in the U.S. are gearing up to produce the large volumes of methyl tertiary butyl ether (MTBE) needed to comply with oxygenated gasoline requirements. The 1990 U.S. Clean Air Act Amendments specify that, as of the first of this coming November, gasoline containing a minimum of 2.7 wt % oxygen must be sold in 39 CO-nonattainment cities. Refiners and others are scurrying to bring MTBE capacity on line in time to meet this requirement. Many U.S. refiners already have some operating MTBE capacity, but this will not be nearly enough to meet the looming increase in demand. As a result, additional capacity is being constructed worldwide.

  4. Conformal refinement of unstructured quadrilateral meshes

    SciTech Connect (OSTI)

    Garmella, Rao [Los Alamos National Laboratory

    2009-01-01T23:59:59.000Z

    We present a multilevel adaptive refinement technique for unstructured quadrilateral meshes in which the mesh is kept conformal at all times. This means that the refined mesh, like the original, is formed of only quadrilateral elements that intersect strictly along edges or at vertices, i.e., vertices of one quadrilateral element do not lie in an edge of another quadrilateral. Elements are refined using templates based on 1:3 refinement of edges. We demonstrate that by careful design of the refinement and coarsening strategy, we can maintain high quality elements in the refined mesh. We demonstrate the method on a number of examples with dynamically changing refinement regions.

  5. Zone refining of plutonium metal

    SciTech Connect (OSTI)

    Blau, M.S.

    1994-08-01T23:59:59.000Z

    The zone refining process was applied to Pu metal containing known amounts of impurities. Rod specimens of plutonium metal were melted into and contained in tantalum boats, each of which was passed horizontally through a three-turn, high-frequency coil in such a manner as to cause a narrow molten zone to pass through the Pu metal rod 10 times. The impurity elements Co, Cr, Fe, Ni, Np, U were found to move in the same direction as the molten zone as predicted by binary phase diagrams. The elements Al, Am, and Ga moved in the opposite direction of the molten zone as predicted by binary phase diagrams. As the impurity alloy was zone refined, {delta}-phase plutonium metal crystals were produced. The first few zone refining passes were more effective than each later pass because an oxide layer formed on the rod surface. There was no clear evidence of better impurity movement at the slower zone refining speed. Also, constant or variable coil power appeared to have no effect on impurity movement during a single run (10 passes). This experiment was the first step to developing a zone refining process for plutonium metal.

  6. ORIGINAL ARTICLE Ambient Air Pollution

    E-Print Network [OSTI]

    Mulholland, James A.

    ORIGINAL ARTICLE Ambient Air Pollution and Respiratory Emergency Department Visits Jennifer L. Peel pollution and respiratory outcomes. More refined assessment has been limited by study size and available air quality data. Methods: Measurements of 5 pollutants (particulate matter PM10 , ozone, nitrogen dioxide NO2

  7. ITP Petroleum Refining: Impacts of Condition Assessment on Energy...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    ITP Petroleum Refining: Impacts of Condition Assessment on Energy Use: Selected Applications in Chemicals Processing and Petroleum Refining ITP Petroleum Refining: Impacts of...

  8. Aircraft Observations of Aerosol Composition and Ageing in New England and Mid-Atlantic States during the Summer 2002 New England Air Quality Study Field Campaign

    SciTech Connect (OSTI)

    Kleinman, Lawrence I.; Daum, Peter H.; Lee, Y.- N.; Senum, Gunar; Springston, Stephen R.; Wang, Jian; Berkowitz, Carl M.; Hubbe, John M.; Zaveri, Rahul A.; Brechtel, Fred J.; Jayne, J. T.; Onasch, Timothy B.; Worsnop, Douglas R.

    2007-05-11T23:59:59.000Z

    Aerosol chemical composition, size distributions, and optical properties were measured during 17 aircraft flights in New England and Middle Atlantic States as part of the summer 2002 NEAQS field campaign. An Aerodyne Aerosol Mass Spectrometer (AMS) was operated with a measurement cycle of 30 s, about an order of magnitude faster than used for ground-based measurements. Noise levels within a single measurement period were sub ?g m-3. Volume data derived from the AMS were compared with volume measurements from a PCASP optical particle detector and an Scanning Mobility Particle Spectrometer (SMPS); calculated light scattering was compared with measured values from an integrating nephelometer. The median ratio for AMS/SMPS volume was 1.25; the median ratio for AMS/nephelometer scattering was 1.18. Size spectra were compared for subsets of samples with different effective diameters (Deff). There is good agreement between the AMS, PCASP, and SMPS spectra for larger values of Deff but an unexplained over-prediction in the AMS for small values. A dependence of the AMS collection efficiency on aerosol acidity was quantified by a comparison between AMS and PCASP volumes in 2 high sulfate plumes. Average aerosol concentrations were 11 ?g m-3. The organic content was high in comparison to monitoring data from the IMPROVE network, varying from 70% in clean air to 40% in high concentration sulfate plumes. The ratio of organic aerosol to CO and light absorption acting were examined as a function of photochemical age. CO is a conservative tracer for urban emissions and light absorption is a surrogate for black carbon which is also conservative. Comparisons were made to surface ratios measured under conditions where there is little secondary organic aerosol (SOA). An increase in these ratios relative to surface values indicates that 70 - 80% of the organic aerosol in polluted air masses was secondary. Most of this SOA is rapidly formed within a few hours. At longer time scales there is a slow accumulation of organic aerosol and a slow increase in light absorption per unit mass of black carbon. Our results demonstrate the utility of the AMS as a rapid response instrument suitable for aircraft operations.

  9. Zone refining of plutonium metal

    SciTech Connect (OSTI)

    NONE

    1997-05-01T23:59:59.000Z

    The purpose of this study was to investigate zone refining techniques for the purification of plutonium metal. The redistribution of 10 impurity elements from zone melting was examined. Four tantalum boats were loaded with plutonium impurity alloy, placed in a vacuum furnace, heated to 700{degrees}C, and held at temperature for one hour. Ten passes were made with each boat. Metallographic and chemical analyses performed on the plutonium rods showed that, after 10 passes, moderate movement of certain elements were achieved. Molten zone speeds of 1 or 2 inches per hour had no effect on impurity element movement. Likewise, the application of constant or variable power had no effect on impurity movement. The study implies that development of a zone refining process to purify plutonium is feasible. Development of a process will be hampered by two factors: (1) the effect on impurity element redistribution of the oxide layer formed on the exposed surface of the material is not understood, and (2) the tantalum container material is not inert in the presence of plutonium. Cold boat studies are planned, with higher temperature and vacuum levels, to determine the effect on these factors. 5 refs., 1 tab., 5 figs.

  10. Reaping Energy Savings from Petroleum Refining

    E-Print Network [OSTI]

    Deng, A.; Cascone, R.

    2006-01-01T23:59:59.000Z

    REAPING ENERGY SAVINGS FROM PETROLEUM REFINING Alan Deng, Project Manager, San Francisco, CA, Ron Cascone, Project Manager, White Plains, NY, Nexant, Inc. ABSTRACT The refining industry is one of the largest energy users in Pacific Gas... years’ energy conservation and demand-side management program participation. The PG&E’s refinery energy efficiency program (REEP) is designed to address key market barriers and tap into the savings potential from energy-intensive refining processes...

  11. U. S. refiners move into another challenging technical era

    SciTech Connect (OSTI)

    Hall, J.R. (Ashland Oil Inc., Ashland, KY (US))

    1991-10-21T23:59:59.000Z

    With the transition to unleaded gasoline scarcely behind us, another new era is dawning for the U.S. refiner. No one yet knows the exact configuration of the refinery of the future and no two refineries are likely to adapt in exactly the same way. What is certain, however, is that by the year 2000, refineries will be more technologically advanced, their products will be more environmentally acceptable, and their operators will be more highly trained. The typical U.S. refinery in the year 2000 will be located at an existing refinery site because economic and environmental considerations will make it impossible to build new grassroots capacity. As a result of the Clean Air act, the refinery of tomorrow will produce cleaner fuels The entire U.S. gasoline pool will likely be reformulated. Most of the diesel fuel pool will consist of ultralow-sulfur product. And jet fuel-which is experiencing rapid demand growth-will be an increasingly important product. Many existing refining process will remain in use, but they will be more efficient and more technologically advanced. Energy efficiency will be a primary concern, as refiners seek to combat ever-increasing crude oil costs and refinery operating expenses. The refinery of the future also will be much more environmentally acceptable. The article is a closer look at the refinery of the future.

  12. Parylene C Aging Studies.

    SciTech Connect (OSTI)

    Achyuthan, Komandoor; Sawyer, Patricia Sue.; Mata, Guillermo Adrian; White II, Gregory Von; Bernstein, Robert

    2014-09-01T23:59:59.000Z

    Parylene C is used in a device because of its conformable deposition and other advantages. Techniques to study Parylene C aging were developed, and %22lessons learned%22 that could be utilized for future studies are the result of this initial study. Differential Scanning Calorimetry yielded temperature ranges for Parylene C aging as well as post-deposition treatment. Post-deposition techniques are suggested to improve Parylene C performance. Sample preparation was critical to aging regimen. Short-term (~40 days) aging experiments with free standing and ceramic-supported Parylene C films highlighted %22lessons learned%22 which stressed further investigations in order to refine sample preparation (film thickness, single sided uniform coating, machine versus laser cutting, annealing time, temperature) and testing issues (%22necking%22) for robust accelerated aging of Parylene C.

  13. North Dakota Refining Capacity Study

    SciTech Connect (OSTI)

    Dennis Hill; Kurt Swenson; Carl Tuura; Jim Simon; Robert Vermette; Gilberto Marcha; Steve Kelly; David Wells; Ed Palmer; Kuo Yu; Tram Nguyen; Juliam Migliavacca

    2011-01-05T23:59:59.000Z

    According to a 2008 report issued by the United States Geological Survey, North Dakota and Montana have an estimated 3.0 to 4.3 billion barrels of undiscovered, technically recoverable oil in an area known as the Bakken Formation. With the size and remoteness of the discovery, the question became 'can a business case be made for increasing refining capacity in North Dakota?' And, if so what is the impact to existing players in the region. To answer the question, a study committee comprised of leaders in the region's petroleum industry were brought together to define the scope of the study, hire a consulting firm and oversee the study. The study committee met frequently to provide input on the findings and modify the course of the study, as needed. The study concluded that the Petroleum Area Defense District II (PADD II) has an oversupply of gasoline. With that in mind, a niche market, naphtha, was identified. Naphtha is used as a diluent used for pipelining the bitumen (heavy crude) from Canada to crude markets. The study predicted there will continue to be an increase in the demand for naphtha through 2030. The study estimated the optimal configuration for the refinery at 34,000 barrels per day (BPD) producing 15,000 BPD of naphtha and a 52 percent refinery charge for jet and diesel yield. The financial modeling assumed the sponsor of a refinery would invest its own capital to pay for construction costs. With this assumption, the internal rate of return is 9.2 percent which is not sufficient to attract traditional investment given the risk factor of the project. With that in mind, those interested in pursuing this niche market will need to identify incentives to improve the rate of return.

  14. Rocky Mountain area petroleum product availability with reduced PADD IV refining capacity

    SciTech Connect (OSTI)

    Hadder, G.R.; Chin, S.M.

    1994-02-01T23:59:59.000Z

    Studies of Rocky Mountain area petroleum product availability with reduced refining capacity in Petroleum Administration for Defense IV (PADD IV, part of the Rocky Mountain area) have been performed with the Oak Ridge National Laboratory Refinery Yield Model, a linear program which has been updated to blend gasolines to satisfy constraints on emissions of nitrogen oxides and winter toxic air pollutants. The studies do not predict refinery closures in PADD IV. Rather, the reduced refining capacities provide an analytical framework for probing the flexibility of petroleum refining and distribution for winter demand conditions in the year 2000. Industry analysts have estimated that, for worst case scenarios, 20 to 35 percent of PADD IV refining capacity could be shut-down as a result of clean air and energy tax legislation. Given these industry projections, the study scenarios provide the following conclusions: The Rocky Mountain area petroleum system would have the capability to satisfy winter product demand with PADD IV refinery capacity shut-downs in the middle of the range of industry projections, but not in the high end of the range of projections. PADD IV crude oil production can be maintained by re-routing crude released from PADD IV refinery demands to satisfy increased crude oil demands in PADDs II (Midwest), III (Gulf Coast), and Washington. Clean Air Act product quality regulations generally do not increase the difficulty of satisfying emissions reduction constraints in the scenarios.

  15. Source: Energy Information Administration, Form EIA-782A, "Refiners...

    U.S. Energy Information Administration (EIA) Indexed Site

    Gallons per Day Motor Gasoline No. 2 Distillate Residual Fuel Oil 5. U.S. Refiner Wholesale Petroleum Product Volumes Figure Percentages of Refiner Wholesale Volumes 1995...

  16. Source: Energy Information Administration, Form EIA-782A, "Refiners...

    Annual Energy Outlook 2013 [U.S. Energy Information Administration (EIA)]

    Gallons per Day Motor Gasoline No. 2 Distillate Residual Fuel Oil 5. U.S. Refiner Wholesale Petroleum Product Volumes Figure Percentages of Refiner Wholesale Volumes 1997...

  17. Source: Energy Information Administration, Form EIA-782A, "Refiners...

    Gasoline and Diesel Fuel Update (EIA)

    Gallons per Day Motor Gasoline No. 2 Distillate Residual Fuel Oil 5. U.S. Refiner Wholesale Petroleum Product Volumes Figure Percentages of Refiner Wholesale Volumes 1996...

  18. Improving NMR Protein Structure Quality by Rosetta Refinement...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    NMR Protein Structure Quality by Rosetta Refinement: A Molecular Replacement Study. Improving NMR Protein Structure Quality by Rosetta Refinement: A Molecular Replacement Study....

  19. Introducing Reference Semantics via Refinement Graeme Smith

    E-Print Network [OSTI]

    Smith, Graeme

    Introducing Reference Semantics via Refinement Graeme Smith Software Verification Research Centre, University of Queensland, Australia smith@svrc.uq.edu.au Abstract. Two types of semantics have been given

  20. CO2 isotopes as tracers of firn air diffusion and age in an Arctic ice cap with summer melting, Devon Island, Canada

    E-Print Network [OSTI]

    Chappellaz, Jérôme

    and the effects of summer melting. The 14 CO2 profile from the permeable firn includes the 1963 thermonuclear peak, and accumulation rates were calibrated with the depth of the 1963 thermonuclear 3 H peak. The average ages for CO2 and the ice matrix. Calibrated with the 1963 peak for thermonuclear 14 CO2, a 21.2-year reaction halftime

  1. Green Petroleum Refining -Mathematical Models for Optimizing Petroleum Refining Under Emission Constraints

    E-Print Network [OSTI]

    Anderson, Charles H.

    Green Petroleum Refining - Mathematical Models for Optimizing Petroleum Refining Under Emission understand that my thesis may be made electronically available to the public. #12;iii Abstract Petroleum and treating options for petroleum refinery waste streams. The performance of the developed model

  2. Transforming and Refining Abstract Constraint Specifications

    E-Print Network [OSTI]

    Walsh, Toby

    Transforming and Refining Abstract Constraint Specifications Alan M. Frisch1 , Brahim Hnich2 , Ian choose model transformations to reduce greatly the amount of effort that is required to solve a problem by systematic search. It is a consid- erable challenge to automate such transformations. A problem may be viewed

  3. Sudbury: Nickel Smelting and Refining Nickel Production

    E-Print Network [OSTI]

    Toohey, Darin W.

    Sudbury: Nickel Smelting and Refining Nickel Production o Toyota buys most of its nickel from Sudbury to produce its nickel- metal hydride batteries Used in cars such as the Toyota Prius SO2 Emissions o The smelting of nickel = large amount of SO2 released as byproduct 4 metric tons of SO2 per

  4. Focus on Venezuelan heavy crude: refining margins

    SciTech Connect (OSTI)

    Not Available

    1984-01-25T23:59:59.000Z

    Of six crudes refined in the US Gulf Coast, heavy Venezuelan crude Lagunillas (15/sup 0/ API) provides the best margin per barrel. Data for end of December 1983 and the first three weeks of January show that margins on all crudes are on the rise in this market, due to a turnaround in product prices. The lighter crudes are showing the greatest increase in Gross Product Worth. This is having a modest shrinking effect on the margin differential between light and heavy crudes in this market. The domestic crude West Texas Intermediate, at 40/sup 0/ API, provides the highest GPW in this crude slate sample, over US $31 per barrel, compared to GPW of under US $28 per barrel for Lagunillas. Still, as Lagunillas cost about US $8 less than does WTI, refiners with sufficient residue conversion capacity can be earning about US $3.50 more in margin per barrel than they can with WTI. Although few refiners would be using a 15/sup 0/ API crude exclusively for any length of time, heavier oil's inclusion in modern refiners' diets is enhancing their competitive position more than any other single factor. This issue of Energy Detente presents the fuel price/tax series and industrial fuel prices for January 1984 for countries of the Western Hemisphere.

  5. Impacts of Mixing on Acceptable Indoor Air Quality in Homes

    E-Print Network [OSTI]

    Sherman, Max H.

    2010-01-01T23:59:59.000Z

    local mean ages of air in buildings for characterizing ventilationof local exhaust increases average whole-house ventilation

  6. Refining industry trends: Europe and surroundings

    SciTech Connect (OSTI)

    Guariguata, U.G.

    1997-05-01T23:59:59.000Z

    The European refining industry, along with its counterparts, is struggling with low profitability due to excess primary and conversion capacity, high operating costs and impending decisions of stringent environmental regulations that will require significant investments with hard to justify returns. This region was also faced in the early 1980s with excess capacity on the order of 4 MMb/d and satisfying the {open_quotes}at that point{close_quotes} demand by operating at very low utilization rates (60%). As was the case in the US, the rebalancing of the capacity led to the closure of some 51 refineries. Since the early 1990s, the increase in demand growth has essentially balanced the capacity threshold and utilization rates are settled around the 90% range. During the last two decades, the major oil companies have reduced their presence in the European refining sector, giving some state oil companies and producing countries the opportunity to gain access to the consumer market through the purchase of refining capacity in various countries-specifically, Kuwait in Italy; Libya and Venezuela in Germany; and Norway in other areas of Scandinavia. Although the market share for this new cast of characters remains small (4%) relative to participation by the majors (35%), their involvement in the European refining business set the foundation whereby US independent refiners relinquished control over assets that could not be operated profitably as part of a previous vertically integrated structure, unless access to the crude was ensured. The passage of time still seems to render this model valid.

  7. Grain Refinement of Permanent Mold Cast Copper Base Alloys

    SciTech Connect (OSTI)

    M.Sadayappan; J.P.Thomson; M.Elboujdaini; G.Ping Gu; M. Sahoo

    2005-04-01T23:59:59.000Z

    Grain refinement is a well established process for many cast and wrought alloys. The mechanical properties of various alloys could be enhanced by reducing the grain size. Refinement is also known to improve casting characteristics such as fluidity and hot tearing. Grain refinement of copper-base alloys is not widely used, especially in sand casting process. However, in permanent mold casting of copper alloys it is now common to use grain refinement to counteract the problem of severe hot tearing which also improves the pressure tightness of plumbing components. The mechanism of grain refinement in copper-base alloys is not well understood. The issues to be studied include the effect of minor alloy additions on the microstructure, their interaction with the grain refiner, effect of cooling rate, and loss of grain refinement (fading). In this investigation, efforts were made to explore and understand grain refinement of copper alloys, especially in permanent mold casting conditions.

  8. 5.841 Crystal Structure Refinement, Fall 2006

    E-Print Network [OSTI]

    Mueller, Peter

    This course in crystal structure refinement examines the practical aspects of crystal structure determination from data collection strategies to data reduction and basic and advanced refinement problems of organic and ...

  9. 5.067 Crystal Structure Refinement, Fall 2007

    E-Print Network [OSTI]

    Mueller, Peter

    This course in crystal structure refinement examines the practical aspects of crystal structure determination from data collection strategies to data reduction and basic and advanced refinement problems of organic and ...

  10. Using supercritical fluids to refine hydrocarbons

    DOE Patents [OSTI]

    Yarbro, Stephen Lee

    2014-11-25T23:59:59.000Z

    This is a method to reactively refine hydrocarbons, such as heavy oils with API gravities of less than 20.degree. and bitumen-like hydrocarbons with viscosities greater than 1000 cp at standard temperature and pressure using a selected fluid at supercritical conditions. The reaction portion of the method delivers lighter weight, more volatile hydrocarbons to an attached contacting device that operates in mixed subcritical or supercritical modes. This separates the reaction products into portions that are viable for use or sale without further conventional refining and hydro-processing techniques. This method produces valuable products with fewer processing steps, lower costs, increased worker safety due to less processing and handling, allow greater opportunity for new oil field development and subsequent positive economic impact, reduce related carbon dioxide, and wastes typical with conventional refineries.

  11. Dinosaurs can fly -- High performance refining

    SciTech Connect (OSTI)

    Treat, J.E. [Booz-Allen and Hamilton, Inc., San Francisco, CA (United States)

    1995-09-01T23:59:59.000Z

    High performance refining requires that one develop a winning strategy based on a clear understanding of one`s position in one`s company`s value chain; one`s competitive position in the products markets one serves; and the most likely drivers and direction of future market forces. The author discussed all three points, then described measuring performance of the company. To become a true high performance refiner often involves redesigning the organization as well as the business processes. The author discusses such redesigning. The paper summarizes ten rules to follow to achieve high performance: listen to the market; optimize; organize around asset or area teams; trust the operators; stay flexible; source strategically; all maintenance is not equal; energy is not free; build project discipline; and measure and reward performance. The paper then discusses the constraints to the implementation of change.

  12. Validating Process Refinement with Ontologies , Gerd Groener2

    E-Print Network [OSTI]

    Staab, Steffen

    Validating Process Refinement with Ontologies Yuan Ren1 , Gerd Groener2 , Jens Lemcke3 , Tirdad University of Koblenz-Landau, 3 SAP AG Abstract. A crucial task in process management is the validation of process refinements. A process refinement is a process description in a more fine-grained representation

  13. MECS 2006 - Petroleum Refining | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels DataDepartment of Energy Your Density Isn't YourTransport(FactDepartment ofLetterEconomy andTermsDepartment1|Petroleum Refining MECS 2006 -

  14. State of heavy oil production and refining in California

    SciTech Connect (OSTI)

    Olsen, D.K.; Ramzel, E.B. [BDM-Oklahoma, Inc., Bartlesville, OK (United States)

    1995-12-31T23:59:59.000Z

    California is unique in the United States because it has the largest heavy oil (10{degrees} to 20{degrees}API gravity) resource, estimated to be in excess of 40 billion barrels. Of the current 941,543 barrels/day of oil produced in California (14% of the U.S. total), 70% or 625,312 barrels/day is heavy oil. Heavy oil constituted only 20% of California`s oil production in the early 1940s, but development of thermal oil production technology in the 1960s allowed the heavy industry to grow and prosper to the point where by the mid-1980s, heavy oil constituted 70% of the state`s oil production. Similar to the rest of the United States, light oil production in the Los Angeles Basin, Coastal Region, and San Joaquin Valley peaked and then declined at different times throughout the past 30 years. Unlike other states, California developed a heavy oil industry that replaced declining light oil production and increased the states total oil production, despite low heavy oil prices, stringent environmental regulations and long and costly delays in developing known oil resources. California`s deep conversion refineries process the nation`s highest sulfur, lowest API gravity crude to make the cleanest transportation fuels available. More efficient vehicles burning cleaner reformulated fuels have significantly reduced the level of ozone precursors (the main contributor to California`s air pollution) and have improved air quality over the last 20 years. In a state where major oil companies dominate, the infrastructure is highly dependent on the 60% of ANS production being refined in California, and California`s own oil production. When this oil is combined with the small volume of imported crude, a local surplus of marketed oil exists that inhibits exploitation of California`s heavy oil resources. As ANS production declines, or if the export restrictions on ANS sales are lifted, a window of opportunity develops for increased heavy oil production.

  15. Electron beam skull melting and refining of secondary copper

    SciTech Connect (OSTI)

    Bychkov, Y.; Ladokhin, S. [Donetskvtortsvetmet, Donetsk (Ukraine)

    1995-12-31T23:59:59.000Z

    Electron Beam Melting is the most efficient technology for metals and alloys refining. For secondary metals processing the Electron Beam Skull Melting (EBSM) with the electromagnetic stirring (EMS) of melt in the crucible was shown to be the most appropriate. The copper produced by EBSM with EMS possesses higher density and electric conductivity in comparison with other refining methods. The details for high power electrical machines were cast of the copper waste refined by EBSM technology.

  16. Projections of the impact of expansion of domestic heavy oil production on the U.S. refining industry from 1990 to 2010. Topical report

    SciTech Connect (OSTI)

    Olsen, D.K.; Ramzel, E.B.; Strycker, A.R. [National Institute for Petroleum and Energy Research, Bartlesville, OK (United States). ITT Research Institute] [National Institute for Petroleum and Energy Research, Bartlesville, OK (United States). ITT Research Institute; Guariguata, G.; Salmen, F.G. [Bonner and Moore Management Science, Houston, TX (United States)] [Bonner and Moore Management Science, Houston, TX (United States)

    1994-12-01T23:59:59.000Z

    This report is one of a series of publications assessing the feasibility of increasing domestic heavy oil (10{degrees} to 20{degrees} API gravity) production. This report provides a compendium of the United States refining industry and analyzes the industry by Petroleum Administration for Defense District (PADD) and by ten smaller refining areas. The refining capacity, oil source and oil quality are analyzed, and projections are made for the U.S. refining industry for the years 1990 to 2010. The study used publicly available data as background. A linear program model of the U.S. refining industry was constructed and validated using 1990 U.S. refinery performance. Projections of domestic oil production (decline) and import of crude oil (increases) were balanced to meet anticipated demand to establish a base case for years 1990 through 2010. The impact of additional domestic heavy oil production, (300 MB/D to 900 MB/D, originating in select areas of the U.S.) on the U.S. refining complex was evaluated. This heavy oil could reduce the import rate and the balance of payments by displacing some imported, principally Mid-east, medium crude. The construction cost for refining units to accommodate this additional domestic heavy oil production in both the low and high volume scenarios is about 7 billion dollars for bottoms conversion capacity (delayed coking) with about 50% of the cost attributed to compliance with the Clean Air Act Amendment of 1990.

  17. Table 44. Refiner Motor Gasoline Volumes by Formulation, Sales...

    Annual Energy Outlook 2013 [U.S. Energy Information Administration (EIA)]

    250 Energy Information AdministrationPetroleum Marketing Annual 1999 Table 44. Refiner Motor Gasoline Volumes by Formulation, Sales Type, PAD District, and State (Thousand Gallons...

  18. Table 44. Refiner Motor Gasoline Volumes by Formulation, Sales...

    Gasoline and Diesel Fuel Update (EIA)

    - - - - W W - - - - - - See footnotes at end of table. 44. Refiner Motor Gasoline Volumes by Formulation, Sales Type, PAD District, and State 292 Energy...

  19. Table 43. Refiner Motor Gasoline Volumes by Grade, Sales Type...

    Annual Energy Outlook 2013 [U.S. Energy Information Administration (EIA)]

    220 Energy Information AdministrationPetroleum Marketing Annual 1998 Table 43. Refiner Motor Gasoline Volumes by Grade, Sales Type, PAD District, and State (Thousand Gallons per...

  20. Table 43. Refiner Motor Gasoline Volumes by Grade, Sales Type...

    Gasoline and Diesel Fuel Update (EIA)

    220 Energy Information AdministrationPetroleum Marketing Annual 1999 Table 43. Refiner Motor Gasoline Volumes by Grade, Sales Type, PAD District, and State (Thousand Gallons per...

  1. Table 35. Refiner Motor Gasoline Prices by Grade, Sales Type...

    Annual Energy Outlook 2013 [U.S. Energy Information Administration (EIA)]

    Energy Information Administration Petroleum Marketing Annual 1995 Table 35. Refiner Motor Gasoline Prices by Grade, Sales Type, PAD District, and State (Cents per Gallon...

  2. Table 35. Refiner Motor Gasoline Prices by Grade, Sales Type...

    Gasoline and Diesel Fuel Update (EIA)

    134 Energy Information AdministrationPetroleum Marketing Annual 1998 Table 35. Refiner Motor Gasoline Prices by Grade, Sales Type, PAD District, and State (Cents per Gallon...

  3. Petroleum Products Table 43. Refiner Motor Gasoline Volumes...

    Annual Energy Outlook 2013 [U.S. Energy Information Administration (EIA)]

    220 Energy Information AdministrationPetroleum Marketing Annual 2000 Table 43. Refiner Motor Gasoline Volumes by Grade, Sales Type, PAD District, and State (Thousand Gallons per...

  4. Table 43. Refiner Motor Gasoline Volumes by Grade, Sales Type...

    Annual Energy Outlook 2013 [U.S. Energy Information Administration (EIA)]

    Energy Information Administration Petroleum Marketing Annual 1995 Table 43. Refiner Motor Gasoline Volumes by Grade, Sales Type, PAD District, and State (Thousand Gallons per...

  5. Petroleum Products Table 43. Refiner Motor Gasoline Volumes...

    Annual Energy Outlook 2013 [U.S. Energy Information Administration (EIA)]

    Energy Information Administration Petroleum Marketing Annual 1995 Table 43. Refiner Motor Gasoline Volumes by Grade, Sales Type, PAD District, and State (Thousand Gallons per...

  6. Table 44. Refiner Motor Gasoline Volumes by Formulation, Sales...

    U.S. Energy Information Administration (EIA) Indexed Site

    250 Energy Information AdministrationPetroleum Marketing Annual 1998 Table 44. Refiner Motor Gasoline Volumes by Formulation, Sales Type, PAD District, and State (Thousand Gallons...

  7. Table 44. Refiner Motor Gasoline Volumes by Formulation, Sales...

    Gasoline and Diesel Fuel Update (EIA)

    Energy Information Administration Petroleum Marketing Annual 1995 Table 44. Refiner Motor Gasoline Volumes by Formulation, Sales Type, PAD District, and State (Thousand Gallons...

  8. Table 35. Refiner Motor Gasoline Prices by Grade, Sales Type...

    Annual Energy Outlook 2013 [U.S. Energy Information Administration (EIA)]

    134 Energy Information AdministrationPetroleum Marketing Annual 1999 Table 35. Refiner Motor Gasoline Prices by Grade, Sales Type, PAD District, and State (Cents per Gallon...

  9. ITP Petroleum Refining: Energy Efficiency Roadmap for Petroleum...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Energy Efficiency Roadmap for Petroleum Refineries in California ITP Petroleum Refining: Energy Efficiency Roadmap for Petroleum Refineries in California refiningroadmap.pdf More...

  10. Table 19. U.S. Refiner Residual Fuel Oil Prices

    U.S. Energy Information Administration (EIA) Indexed Site

    Prices," source for backcast estimates prior to January 1983. 19. U.S. Refiner Residual Fuel Oil Prices 36 Energy Information Administration Petroleum Marketing Annual 1997...

  11. Table 19. U.S. Refiner Residual Fuel Oil Prices

    U.S. Energy Information Administration (EIA) Indexed Site

    Prices," source for backcast estimates prior to January 1983. 19. U.S. Refiner Residual Fuel Oil Prices 36 Energy Information Administration Petroleum Marketing Annual 1996...

  12. Source: Energy Information Administration, Form EIA-782A, "Refiners...

    U.S. Energy Information Administration (EIA) Indexed Site

    Refiner Retail Volumes 1996 Annual Averages Motor Gasoline No. 2 Distillate Propane Kero-jet Residual Fuel Oil Other Energy Information Administration Petroleum Marketing Annual...

  13. Source: Energy Information Administration, Form EIA-782A, "Refiners...

    U.S. Energy Information Administration (EIA) Indexed Site

    Refiner Retail Volumes 1997 Annual Averages Motor Gasoline No. 2 Distillate Propane Kero-jet Residual Fuel Oil Other Energy Information Administration Petroleum Marketing Annual...

  14. Adaptively refined large eddy simulations of clusters

    E-Print Network [OSTI]

    Maier, A; Schmidt, W; Niemeyer, J C

    2009-01-01T23:59:59.000Z

    We present a numerical scheme for modelling unresolved turbulence in cosmological adaptive mesh refinement codes. As a first application, we study the evolution of turbulence in the intra-cluster medium and in the core of a galaxy cluster. Simulations with and without subgrid scale model are compared in detail. Since the flow in the ICM is subsonic, the global turbulent energy contribution at the unresolved length scales is smaller than 1% of the internal energy. We find that the production of turbulence is closely correlated with merger events occurring in the cluster environment, and its dissipation locally affects the cluster energy budget. Because of this additional source of dissipation, the core temperature is larger and the density is smaller in the presence of subgrid scale turbulence than in the standard adiabatic run, resulting in a higher entropy core value.

  15. Parallel Triangular Decompositions of an Oil Refining Simulation Xiaodong Zhang

    E-Print Network [OSTI]

    Moreno Maza, Marc

    important process in oil refining is to separate the crude oil into various oil products. This process the composition of the various oil products in designed refining columns operated under a given set of conditions oil products. This process is called distilla- tion, which is a thermal separation method

  16. Specification and Refinement of a RealTime Control System

    E-Print Network [OSTI]

    Smith, Graeme

    such approach via the specification and refinement of the well­known Steam Boiler Control Problem. The case. These features, although not central to the Steam Boiler Control Problem, are typical of features which must­level (i.e., abstract) specification of the Steam Boiler Control Problem. This specification is refined

  17. Feasibility of Organizations -A Refinement of Chemical Organization Theory

    E-Print Network [OSTI]

    Hinze, Thomas

    Feasibility of Organizations - A Refinement of Chemical Organization Theory with Application to P a theorem providing a criteria for an unfeasible organization. This is a refinement of organization theory organization. Key words: reaction networks, constructive dynamical systems, chem- ical organization theory

  18. Changing System Interfaces Consistently: a New Refinement Strategy for CSP B

    E-Print Network [OSTI]

    Doran, Simon J.

    Changing System Interfaces Consistently: a New Refinement Strategy for CSP B Steve Schneider refinement in the context of CSP B. Our motivation to include this notion of refinement within the CSP B to change the events of a CSP process and the B machines when refining a system. Notions of refinement based

  19. Electron beam cold hearth refining in Vallejo

    SciTech Connect (OSTI)

    Lowe, J.H.C. [Axel Johnson Metals, Inc., Vallejo, CA (United States)

    1994-12-31T23:59:59.000Z

    Electron Beam Cold Hearth Refining Furnace (EBCHR) in Vallejo, California is alive, well, and girding itself for developing new markets. A brief review of the twelve years experience with EBCHR in Vallejo. Acquisition of the Vallejo facility by Axel Johnson Metals, Inc. paves the way for the development of new products and markets. A discussion of some of the new opportunities for the advancement of EBCHR technology. Discussed are advantages to the EBCHR process which include: extended surface area of molten metal exposed to higher vacuum; liberation of insoluble oxide particles to the surface of the melt; higher temperatures that allowed coarse solid particles like carbides and carbonitrides to be suspended in the fluid metal as fine micro-segregates, and enhanced removal of volatile trace impurities like lead, bismuth and cadmium. Future work for the company includes the continued recycling of alloys and also fabricating stainless steel for the piping of chip assembly plants. This is to prevent `killer defects` that ruin a memory chip.

  20. GRChombo : Numerical Relativity with Adaptive Mesh Refinement

    E-Print Network [OSTI]

    Katy Clough; Pau Figueras; Hal Finkel; Markus Kunesch; Eugene A. Lim; Saran Tunyasuvunakool

    2015-03-11T23:59:59.000Z

    Numerical relativity has undergone a revolution in the past decade. With a well-understood mathematical formalism, and full control over the gauge modes, it is now entering an era in which the science can be properly explored. In this work, we introduce GRChombo, a new numerical relativity code written to take full advantage of modern parallel computing techniques. GRChombo's features include full adaptive mesh refinement with block structured Berger-Rigoutsos grid generation which supports non-trivial "many-boxes-in-many-boxes" meshing hierarchies, and massive parallelism through the Message Passing Interface (MPI). GRChombo evolves the Einstein equation with the standard BSSN formalism, with an option to turn on CCZ4 constraint damping if required. We show that GRChombo passes all the standard "Apples-to-Apples" code comparison tests. We also show that it can stably and accurately evolve vacuum black hole spacetimes such as binary black hole mergers, and non-vacuum spacetimes such as scalar collapses into black holes. As an illustration of its AMR capability, we demonstrate the evolution of triple black hole merger, which can be set up trivially in GRChombo.

  1. GRChombo : Numerical Relativity with Adaptive Mesh Refinement

    E-Print Network [OSTI]

    Clough, Katy; Finkel, Hal; Kunesch, Markus; Lim, Eugene A; Tunyasuvunakool, Saran

    2015-01-01T23:59:59.000Z

    Numerical relativity has undergone a revolution in the past decade. With a well-understood mathematical formalism, and full control over the gauge modes, it is now entering an era in which the science can be properly explored. In this work, we introduce GRChombo, a new numerical relativity code written to take full advantage of modern parallel computing techniques. GRChombo's features include full adaptive mesh refinement with block structured Berger-Rigoutsos grid generation which supports non-trivial "many-boxes-in-many-boxes" meshing hierarchies, and massive parallelism through the Message Passing Interface (MPI). GRChombo evolves the Einstein equation with the standard BSSN formalism, with an option to turn on CCZ4 constraint damping if required. We show that GRChombo passes all the standard "Apples-to-Apples" code comparison tests. We also show that it can stably and accurately evolve vacuum black hole spacetimes such as binary black hole mergers, and non-vacuum spacetimes such as scalar collapses into b...

  2. Aging behavior and lifetime modeling for polycarbonate

    SciTech Connect (OSTI)

    Kahlen, S. [Polymer Competence Center Leoben GmbH, Roseggerstrasse 12, Leoben 8700 (Austria); Wallner, G.M. [Institute of Materials Science and Testing of Plastics, University of Leoben, Franz-Josef Strasse 18, Leoben 8700 (Austria); Lang, R.W. [Institute for Polymeric Materials and Testing, University of Linz, Altenbergerstrasse 69, Linz 4040 (Austria)

    2010-05-15T23:59:59.000Z

    In this paper, polycarbonate (PC) as a material candidate for solar absorber applications is investigated as to the aging behavior at different temperatures in air and water. The aging conditioning was performed in air in the temperature range from 120 to 140 C and in water between 70 and 95 C. Tensile tests were performed on unaged and aged PC film specimens at ambient temperature using strain-to-break values as a performance indicator for the degree of aging. For PC the effect of aging was found to strongly depend on the aging conditions. Activation energy based lifetime prediction models according to various methods described in the literature were applied. The activation energies and corresponding lifetime predictions for the temperature range from 40 to 60 C in water and from 90 to 110 C in air derived from these models are compared and interpreted as to their practical relevance. (author)

  3. Hydrogen and Fuel Cells - Refining the Message Initiating a National Dialogue and Educational Agenda

    E-Print Network [OSTI]

    Eggert, Anthony; Kurani, Kenneth S; Turrentine, Tom; Ogden, Joan M; Sperling, Dan; Winston, Emily

    2005-01-01T23:59:59.000Z

    April 1, 2005 Hydrogen and Fuel Cells – Refining the MessageHydrogen and Fuel Cells – Refining the Message Initiating athe communication problem. Hydrogen and fuel cells have now

  4. E-Print Network 3.0 - amerya petroleum refining Sample Search...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    ) Petroleum Refining Efficiency: 150 ppm S RFG with MTBE: GBS (d) Petroleum Refining... Eficiency: ... Source: Argonne National Laboratory - GREET Model Project Collection:...

  5. Iterative model-building, structure refinement, and density modification with the PHENIX AutoBuild Wizard

    E-Print Network [OSTI]

    Terwilliger, T. C.; Los Alamos National Laboratory, Mailstop M888, Los Alamos, NM 87545, USA; Lawrence Berkeley National Laboratory, One Cyclotron Road, Building 64R0121, Berkeley, CA 94720, USA; Department of Haematology, University of Cambridge, Cambridge CB2 0XY, England

    2008-01-01T23:59:59.000Z

    Iterative model-building, structure refinement, and densitytool for iterative model- building, structure refinement andusing RESOLVE or TEXTAL model- building, RESOLVE statistical

  6. Source: Energy Information Administration, Form EIA-782A, "Refiners...

    U.S. Energy Information Administration (EIA) Indexed Site

    S O N D 0 10 20 30 40 50 60 70 1995 Cents per Gallon Excluding Taxes Retail < or 1% Wholesale < or 1% Retail > 1% Wholesale > 1% 7. U.S. Refiner Residual Fuel Oil Prices and...

  7. Table 43. Refiner Motor Gasoline Volumes by Grade, Sales Type...

    Gasoline and Diesel Fuel Update (EIA)

    150.0 2,026.7 W W 234.5 161.7 - 396.3 See footnotes at end of table. 43. Refiner Motor Gasoline Volumes by Grade, Sales Type, PAD District, and State 262 Energy Information...

  8. Table 43. Refiner Motor Gasoline Volumes by Grade, Sales Type...

    Annual Energy Outlook 2013 [U.S. Energy Information Administration (EIA)]

    253.2 2,222.4 W W 206.4 134.3 - 340.7 See footnotes at end of table. 43. Refiner Motor Gasoline Volumes by Grade, Sales Type, PAD District, and State 262 Energy Information...

  9. Petroleum Products Table 43. Refiner Motor Gasoline Volumes...

    Annual Energy Outlook 2013 [U.S. Energy Information Administration (EIA)]

    150.0 2,026.7 W W 234.5 161.7 - 396.3 See footnotes at end of table. 43. Refiner Motor Gasoline Volumes by Grade, Sales Type, PAD District, and State 262 Energy Information...

  10. Petroleum Products Table 43. Refiner Motor Gasoline Volumes...

    Annual Energy Outlook 2013 [U.S. Energy Information Administration (EIA)]

    253.2 2,222.4 W W 206.4 134.3 - 340.7 See footnotes at end of table. 43. Refiner Motor Gasoline Volumes by Grade, Sales Type, PAD District, and State 262 Energy Information...

  11. Consensus Clustering Algorithms: Comparison and Refinement Andrey Goder

    E-Print Network [OSTI]

    Filkov, Vladimir

    -deterministic clustering algorithms, e.g. K-means, are sensitive to the choice of the initial seed clusters; running K-meansConsensus Clustering Algorithms: Comparison and Refinement Andrey Goder Vladimir Filkov Computer

  12. Source: Energy Information Administration, Form EIA-782A, "Refiners...

    U.S. Energy Information Administration (EIA) Indexed Site

    Refiner Retail Volumes 1995 Annual Averages Motor Gasoline No. 2 Distillate Propane Kero-jet Residual Fuel Oil Other 39.1% 17.4% 2.2% 32.0% 8.1% 1.1% Energy Information...

  13. Japan`s refiner/marketers headed for major shakeout

    SciTech Connect (OSTI)

    NONE

    1996-08-26T23:59:59.000Z

    Japan`s downstream oil industry is in a state of crisis and headed for a major shakeout. The major catalyst for this was a dramatic deregulation step during April 1996 that allowed refined petroleum product imports by non-refiners. The move, together with a sharp drop in refining margins, falling retail gasoline prices, and a service station sector on the brink of collapse, are all leading to massive changes in the way the country`s refiners and marketers do business. This paper reviews the collapse of corporate profits during this period of deregulation; the development of a new price system geared toward bringing the prices of gasoline, fuel oil, and kerosene into line with each other to offset the fall in gasoline prices; and industry restructuring including mergers, acquisitions, and marketing consolidation. The paper then makes predictions on the outcome of these changes on the Japanese oil industry.

  14. Polygons in Buildings and their Refined Side Lengths

    E-Print Network [OSTI]

    Kapovich, Michael; Leeb, Bernhard; Millson, John J.

    2009-01-01T23:59:59.000Z

    1999. [Bro] K. Brown, Buildings, Springer, 1989. [BuBI] D.AMS, 2001. [D] M. Davis, Buildings are CAT(0), in “Geometryat Springerlink.com POLYGONS IN BUILDINGS AND THEIR REFINED

  15. Steps taken at Malelane refinery to improve refined sugar quality

    E-Print Network [OSTI]

    M Moodley; Pm Schorn

    1997-01-01T23:59:59.000Z

    The refinery at Malelane has in the past produced refined sugar for the consumer market. A decision was taken by the management of Transvaal Sugar (TSB) to produce a quality of refined sugar that would also be acceptable to the industrial and the export markets. The processes that were evaluated and implemented at the Malelane refinery during the past three seasons to achieve this objective, are described.

  16. Refiners Switch to RFG Complex Model

    Reports and Publications (EIA)

    1998-01-01T23:59:59.000Z

    On January 1, 1998, domestic and foreign refineries and importers must stop using the "simple" model and begin using the "complex" model to calculate emissions of volatile organic compounds (VOC), toxic air pollutants (TAP), and nitrogen oxides (NOx) from motor gasoline. The primary differences between application of the two models is that some refineries may have to meet stricter standards for the sulfur and olefin content of the reformulated gasoline (RFG) they produce and all refineries will now be held accountable for NOx emissions. Requirements for calculating emissions from conventional gasoline under the anti-dumping rule similarly change for exhaust TAP and NOx. However, the change to the complex model is not expected to result in an increase in the price premium for RFG or constrain supplies.

  17. Air Quality: Construction Project Air Permit Requirements

    E-Print Network [OSTI]

    Wechsler, Risa H.

    Air Quality: Construction Project Air Permit Requirements Department: Chemical and General Safety Program: Air Quality Owner: Program Manager Authority: ES&H Manual, Chapter 30, Air Quality1 All manager or operator must submit the completed form to the air quality program manager before the project

  18. Adaptive mesh refinement for shocks and material interfaces

    SciTech Connect (OSTI)

    Dai, William Wenlong [Los Alamos National Laboratory

    2010-01-01T23:59:59.000Z

    There are three kinds of adaptive mesh refinement (AMR) in structured meshes. Block-based AMR sometimes over refines meshes. Cell-based AMR treats cells cell by cell and thus loses the advantage of the nature of structured meshes. Patch-based AMR is intended to combine advantages of block- and cell-based AMR, i.e., the nature of structured meshes and sharp regions of refinement. But, patch-based AMR has its own difficulties. For example, patch-based AMR typically cannot preserve symmetries of physics problems. In this paper, we will present an approach for a patch-based AMR for hydrodynamics simulations. The approach consists of clustering, symmetry preserving, mesh continuity, flux correction, communications, management of patches, and load balance. The special features of this patch-based AMR include symmetry preserving, efficiency of refinement across shock fronts and material interfaces, special implementation of flux correction, and patch management in parallel computing environments. To demonstrate the capability of the AMR framework, we will show both two- and three-dimensional hydrodynamics simulations with many levels of refinement.

  19. Air Pollution (Illinois)

    Broader source: Energy.gov [DOE]

    This article states regulations for monitoring air pollution, methods for permit applications, emission limitations for pollutants and air quality standards.

  20. Clearing the Air? The Effects of Gasoline Content Regulation on Air Quality

    E-Print Network [OSTI]

    Auffhammer, Maximilian; Kellogg, Ryan

    2009-01-01T23:59:59.000Z

    gasoline distribution stations. Refiners and wholesale terminalsgasoline distribution stations. Refiners and wholesale terminalsgasoline stations and May 1 – September 15 for refiners and wholesale distribution terminals.

  1. Numerical solution of plasma fluid equations using locally refined grids

    SciTech Connect (OSTI)

    Colella, P., LLNL

    1997-01-26T23:59:59.000Z

    This paper describes a numerical method for the solution of plasma fluid equations on block-structured, locally refined grids. The plasma under consideration is typical of those used for the processing of semiconductors. The governing equations consist of a drift-diffusion model of the electrons and an isothermal model of the ions coupled by Poisson's equation. A discretization of the equations is given for a uniform spatial grid, and a time-split integration scheme is developed. The algorithm is then extended to accommodate locally refined grids. This extension involves the advancement of the discrete system on a hierarchy of levels, each of which represents a degree of refinement, together with synchronization steps to ensure consistency across levels. A brief discussion of a software implementation is followed by a presentation of numerical results.

  2. The US petroleum refining industry in the 1980's

    SciTech Connect (OSTI)

    Not Available

    1990-10-11T23:59:59.000Z

    As part of the EIA program on petroleum, The US Petroleum Refining Industry in the 1980's, presents a historical analysis of the changes that took place in the US petroleum refining industry during the 1980's. It is intended to be of interest to analysts in the petroleum industry, state and federal government officials, Congress, and the general public. The report consists of six chapters and four appendices. Included is a detailed description of the major events and factors that affected the domestic refining industry during this period. Some of the changes that took place in the 1980's are the result of events that started in the 1970's. The impact of these events on US refinery configuration, operations, economics, and company ownership are examined. 23 figs., 11 tabs.

  3. Trends in heavy oil production and refining in California

    SciTech Connect (OSTI)

    Olsen, D.K.; Ramzel, E.B.; Pendergrass, R.A. II.

    1992-07-01T23:59:59.000Z

    This report is one of a series of publications assessing the feasibility of increasing domestic heavy oil production and is part of a study being conducted for the US Department of Energy. This report summarizes trends in oil production and refining in Canada. Heavy oil (10{degrees} to 20{degrees} API gravity) production in California has increased from 20% of the state's total oil production in the early 1940s to 70% in the late 1980s. In each of the three principal petroleum producing districts (Los Angeles Basin, Coastal Basin, and San Joaquin Valley) oil production has peaked then declined at different times throughout the past 30 years. Thermal production of heavy oil has contributed to making California the largest producer of oil by enhanced oil recovery processes in spite of low oil prices for heavy oil and stringent environmental regulation. Opening of Naval Petroleum Reserve No. 1, Elk Hills (CA) field in 1976, brought about a major new source of light oil at a time when light oil production had greatly declined. Although California is a major petroleum-consuming state, in 1989 the state used 13.3 billion gallons of gasoline or 11.5% of US demand but it contributed substantially to the Nation's energy production and refining capability. California is the recipient and refines most of Alaska's 1.7 million barrel per day oil production. With California production, Alaskan oil, and imports brought into California for refining, California has an excess of oil and refined products and is a net exporter to other states. The local surplus of oil inhibits exploitation of California heavy oil resources even though the heavy oil resources exist. Transportation, refining, and competition in the market limit full development of California heavy oil resources.

  4. Trends in heavy oil production and refining in California

    SciTech Connect (OSTI)

    Olsen, D.K.; Ramzel, E.B.; Pendergrass, R.A. II

    1992-07-01T23:59:59.000Z

    This report is one of a series of publications assessing the feasibility of increasing domestic heavy oil production and is part of a study being conducted for the US Department of Energy. This report summarizes trends in oil production and refining in Canada. Heavy oil (10{degrees} to 20{degrees} API gravity) production in California has increased from 20% of the state`s total oil production in the early 1940s to 70% in the late 1980s. In each of the three principal petroleum producing districts (Los Angeles Basin, Coastal Basin, and San Joaquin Valley) oil production has peaked then declined at different times throughout the past 30 years. Thermal production of heavy oil has contributed to making California the largest producer of oil by enhanced oil recovery processes in spite of low oil prices for heavy oil and stringent environmental regulation. Opening of Naval Petroleum Reserve No. 1, Elk Hills (CA) field in 1976, brought about a major new source of light oil at a time when light oil production had greatly declined. Although California is a major petroleum-consuming state, in 1989 the state used 13.3 billion gallons of gasoline or 11.5% of US demand but it contributed substantially to the Nation`s energy production and refining capability. California is the recipient and refines most of Alaska`s 1.7 million barrel per day oil production. With California production, Alaskan oil, and imports brought into California for refining, California has an excess of oil and refined products and is a net exporter to other states. The local surplus of oil inhibits exploitation of California heavy oil resources even though the heavy oil resources exist. Transportation, refining, and competition in the market limit full development of California heavy oil resources.

  5. Chronological refinement of an ice core record at Upper Fremont Glacier in south central North America

    SciTech Connect (OSTI)

    Schuster, Paul F. [U.S. Geological Survey, Water Resources Division, Boulder, Colorado (United States)] [U.S. Geological Survey, Water Resources Division, Boulder, Colorado (United States); White, David E. [Golden Software, Golden, Colorado (United States)] [Golden Software, Golden, Colorado (United States); Naftz, David L. [U.S. Geological Survey, Water Resources Division, Salt Lake City, Utah (United States)] [U.S. Geological Survey, Water Resources Division, Salt Lake City, Utah (United States); Cecil, L. DeWayne [U.S. Geological Survey, Water Resources Division, Idaho Falls, Idaho (United States)] [U.S. Geological Survey, Water Resources Division, Idaho Falls, Idaho (United States)

    2000-02-27T23:59:59.000Z

    The potential to use ice cores from alpine glaciers in the midlatitudes to reconstruct paleoclimatic records has not been widely recognized. Although excellent paleoclimatic records exist for the polar regions, paleoclimatic ice core records are not common from midlatitude locations. An ice core removed from the Upper Fremont Glacier in Wyoming provides evidence for abrupt climate change during the mid-1800s. Volcanic events (Krakatau and Tambora) identified from electrical conductivity measurements (ECM) and isotopic and chemical data from the Upper Fremont Glacier were reexamined to confirm and refine previous chronological estimates of the ice core. At a depth of 152 m the refined age-depth profile shows good agreement (1736{+-}10 A.D.) with the {sup 14}C age date (1729{+-}95 A.D.). The {delta}{sup 18}O profile of the Upper Fremont Glacier (UFG) ice core indicates a change in climate known as the Little Ice Age (LIA). However, the sampling interval for {delta}{sup 18}O is sufficiently large (20 cm) such that it is difficult to pinpoint the LIA termination on the basis of {delta}{sup 18}O data alone. Other research has shown that changes in the {delta}{sup 18}O variance are generally coincident with changes in ECM variance. The ECM data set contains over 125,000 data points at a resolution of 1 data point per millimeter of ice core. A 999-point running average of the ECM data set and results from f tests indicates that the variance of the ECM data decreases significantly at about 108 m. At this depth, the age-depth profile predicts an age of 1845 A.D. Results indicate the termination of the LIA was abrupt with a major climatic shift to warmer temperatures around 1845 A.D. and continuing to present day. Prediction limits (error bars) calculated for the profile ages are {+-}10 years (90% confidence level). Thus a conservative estimate for the time taken to complete the LIA climatic shift to present-day climate is about 10 years, suggesting the LIA termination in alpine regions of central North America may have occurred on a relatively short (decadal) timescale. (c) 2000 American Geophysical Union.

  6. Time Critical Isosurface Refinement And Smoothing V. Pascucci

    E-Print Network [OSTI]

    Texas at Austin, University of

    the global geometry of the embedding (no self- intersections) of any approximated level of detail: (i) a progressive al- gorithm that builds a multi-resolution surface by successive refine- ments so of the U.S. Depart- ment of Energy by University of California Lawrence Livermore National Laboratory under

  7. Source: Energy Information Administration, Form EIA-782A, "Refiners...

    U.S. Energy Information Administration (EIA) Indexed Site

    4. U.S. Refiner Wholesale Petroleum Product Prices Figure J F M A M J J A S O N D 0 20 40 60 80 100 120 1996 Cents per Gallon Excluding Taxes Kero-jet Propane No. 1 Distillate No....

  8. Source: Energy Information Administration, Form EIA-782A, "Refiners...

    Gasoline and Diesel Fuel Update (EIA)

    4. U.S. Refiner Wholesale Petroleum Product Prices Figure J F M A M J J A S O N D 0 20 40 60 80 100 120 1995 Cents per Gallon Excluding Taxes Kero-jet Propane No. 1 Distillate No....

  9. Source: Energy Information Administration, Form EIA-782A, "Refiners...

    Annual Energy Outlook 2013 [U.S. Energy Information Administration (EIA)]

    4. U.S. Refiner Wholesale Petroleum Product Prices Figure J F M A M J J A S O N D 0 20 40 60 80 100 120 1997 Cents per Gallon Excluding Taxes Kero-jet Propane No. 1 Distillate No....

  10. Table 35. Refiner Motor Gasoline Prices by Grade, Sales Type...

    U.S. Energy Information Administration (EIA) Indexed Site

    71.8 W 70.5 78.9 W 76.0 83.6 W 69.2 75.2 See footnotes at end of table. 35. Refiner Motor Gasoline Prices by Grade, Sales Type, PAD District and State 176 Energy Information...

  11. Table 35. Refiner Motor Gasoline Prices by Grade, Sales Type...

    Gasoline and Diesel Fuel Update (EIA)

    W 68.4 70.8 W W 78.6 W 85.7 81.8 W 69.3 73.8 See footnotes at end of table. 35. Refiner Motor Gasoline Prices by Grade, Sales Type, PAD District and State 176 Energy Information...

  12. Refinement of the One-Copy Serializable Correctness Criterion

    E-Print Network [OSTI]

    Muñoz, Francesc

    Refinement of the One-Copy Serializable Correctness Criterion M. I. Ruiz-Fuertes, F. D. Mu~noz-Esco. Mu~noz-Esco´i Instituto Tecnol´ogico de Inform´atica Universidad Polit´ecnica de Valencia Camino de

  13. Electron beam melting and refining state of the art 1995

    SciTech Connect (OSTI)

    Bakish, R. [ed.

    1995-12-31T23:59:59.000Z

    This is the proceedings of the Electron Beam Melting and Refining - State of the Art 1995 Conference. It contains 23 of the 30 scheduled papers. Papers cover an array of electron beam melting applications, from industrial plating of metal strip, through government work on manufacturing and processing fissile alloys. Separate abstracts have been prepared for articles from this proceedings.

  14. Refining Hygienic Macros for Modules and Separate Compilation Matthias Blume

    E-Print Network [OSTI]

    Blume, Matthias

    Refining Hygienic Macros for Modules and Separate Compilation Matthias Blume Department of Computer of the assumptions hygienic macro systems are based on. We will investigate how these assumptions have to be changed, and the consequences for the construction of hygienic macro expanders. Macro expansion algorithms rely on their ability

  15. Note on refined topological vertex, Jack polynomials and instanton counting

    E-Print Network [OSTI]

    Jianfeng Wu

    2010-12-10T23:59:59.000Z

    In this article, we calculated the refined topological vertex for the one parameter case using the Jack symmetric functions. Also, we obtain the partition function for elliptic N=2 models, the results coincide with those of Nekrasov instanton counting partition functions for the $N=2^{\\ast}$ theories.

  16. #PRL --A Proof Refinement Calculus for Classical Reasoning

    E-Print Network [OSTI]

    Kreitz, Christoph

    #µPRL -- A Proof Refinement Calculus for Classical Reasoning in Computational Type Theory Nuria, 14482 Potsdam, Germany {brede,kreitz}@cs.uni­potsdam.de Abstract. We present a hybrid proof calculus #µPRL to con­ structive proofs and show that the restriction of #µPRL to µ­safe proof terms is sound

  17. PRL A Proof Refinement Calculus for Classical Reasoning

    E-Print Network [OSTI]

    Kreitz, Christoph

    µPRL ­ A Proof Refinement Calculus for Classical Reasoning in Computational Type Theory Nuria Brede, Germany {brede,kreitz}@cs.uni-potsdam.de Abstract. We present a hybrid proof calculus µPRL that combines and show that the restriction of µPRL to µ-safe proof terms is sound and complete for intuitionistic

  18. Refining 31 P nuclear magnetic resonance spectroscopy for marine

    E-Print Network [OSTI]

    Paytan, Adina

    Refining 31 P nuclear magnetic resonance spectroscopy for marine particulate samples: Storage 31 P nuclear magnetic resonance (NMR) spectroscopy has recently been used to characterize phosphorus.e., no storage, refrigeration, freezing, and oven-drying and grinding) prior to extraction for solution 31 P

  19. Department of Computing Stepwise Refinement in Event-B||CSP

    E-Print Network [OSTI]

    Doran, Simon J.

    in Event-B||CSP Part 1: Safety Steve Schneider, Helen Treharne and Heike Wehrheim March 12th 2011 #12;Stepwise Refinement in Event-B CSP Part 1: Safety Steve Schneider1 Helen Treharne1 Heike Wehrheim2 1, 2011 Contents 1 Introduction 3 2 CSP 3 2.1 Notation

  20. An accuracy study of mesh refinement on mapped grids

    E-Print Network [OSTI]

    Calhoun, Donna

    An accuracy study of mesh refinement on mapped grids D. Calhoun and R. J. LeVeque, October, 2003 on a highly skewed portion of a mapped grid. Smooth and shock-wave solutions to the Euler equations are used interface. Key words: gas dynamics, finite-volume, finite-difference, Cartesian grid, mapped grids

  1. Metal-Air Batteries

    SciTech Connect (OSTI)

    Zhang, Jiguang; Bruce, Peter G.; Zhang, Gregory

    2011-08-01T23:59:59.000Z

    Metal-air batteries have much higher specific energies than most currently available primary and rechargeable batteries. Recent advances in electrode materials and electrolytes, as well as new designs on metal-air batteries, have attracted intensive effort in recent years, especially in the development of lithium-air batteries. The general principle in metal-air batteries will be reviewed in this chapter. The materials, preparation methods, and performances of metal-air batteries will be discussed. Two main metal-air batteries, Zn-air and Li-air batteries will be discussed in detail. Other type of metal-air batteries will also be described.

  2. The use of Fourier reverse transforms in crystallographic phase refinement

    SciTech Connect (OSTI)

    Ringrose, S.

    1997-10-08T23:59:59.000Z

    Often a crystallographer obtains an electron density map which shows only part of the structure. In such cases, the phasing of the trial model is poor enough that the electron density map may show peaks in some of the atomic positions, but other atomic positions are not visible. There may also be extraneous peaks present which are not due to atomic positions. A method for determination of crystal structures that have resisted solution through normal crystallographic methods has been developed. PHASER is a series of FORTRAN programs which aids in the structure solution of poorly phased electron density maps by refining the crystallographic phases. It facilitates the refinement of such poorly phased electron density maps for difficult structures which might otherwise not be solvable. The trial model, which serves as the starting point for the phase refinement, may be acquired by several routes such as direct methods or Patterson methods. Modifications are made to the reverse transform process based on several assumptions. First, the starting electron density map is modified based on the fact that physically the electron density map must be non-negative at all points. In practice a small positive cutoff is used. A reverse Fourier transform is computed based on the modified electron density map. Secondly, the authors assume that a better electron density map will result by using the observed magnitudes of the structure factors combined with the phases calculated in the reverse transform. After convergence has been reached, more atomic positions and less extraneous peaks are observed in the refined electron density map. The starting model need not be very large to achieve success with PHASER; successful phase refinement has been achieved with a starting model that consists of only 5% of the total scattering power of the full molecule. The second part of the thesis discusses three crystal structure determinations.

  3. Air temperature thresholds for indoor comfort and perceived air quality

    E-Print Network [OSTI]

    Zhang, Hui; Edward, Arens; Pasut, Wilmer

    2012-01-01T23:59:59.000Z

    system on perceived air quality, Indoor Air 2008, August 17-perception of indoor air quality during immediate and longeraddressing indoor air quality, thermal environment, lighting

  4. Air temperature thresholds for indoor comfort and perceived air quality

    E-Print Network [OSTI]

    Zhang, Hui; Edward, Arens; Pasut, Wilmer

    2012-01-01T23:59:59.000Z

    in the Netherlands, Indoor Air 2, 127 – 136. BuildingPaliaga, G. (2009) Moving air for comfort. ASHRAE Journal,ventilation system on perceived air quality, Indoor Air

  5. Feasibility of air capture

    E-Print Network [OSTI]

    Ranjan, Manya

    2010-01-01T23:59:59.000Z

    Capturing CO2 from air, referred to as Air Capture, is being proposed as a viable climate change mitigation technology. The two major benefits of air capture, reported in literature, are that it allows us to reduce the ...

  6. Moving air for comfort

    E-Print Network [OSTI]

    Arens, Edward; Turner, Stephen; Zhang, Hui; Paliaga, Gwelen

    2009-01-01T23:59:59.000Z

    Brager, L. Zagreus. 2007, “Air movement preferences observed709-731. 9. Toftum, J. 2004. “Air movement – good or bad? ”Indoor Air 14, pp 40-45. 10. Gong, N. , K. Tham, A. Melikov,

  7. Development of miscella refining process for cottonseed oil-isopropyl alcohol system: laboratory-scale evaluations

    E-Print Network [OSTI]

    Chau, Chi-Fai

    1994-01-01T23:59:59.000Z

    A technologically feasible cottonseed oil-isopropyl alcohol (IPA) miscella refining process was developed to produce high quality cottonseed oil. Individual steps necessary to refine cottonseed oil-IPA miscella were determined and improved...

  8. WELDABILITY OF GRAIN-REFINED Fe-12Ni-0.25Ti STEEL FOR CRYOGENIC APPLICATIONS

    E-Print Network [OSTI]

    Morris Jr., J.W.

    2013-01-01T23:59:59.000Z

    of the Cryogenic Nickel Steels, WRC Bull, 205, May, 1975.REFINED Fe-12Ni-0.25Ti STEEL FOR CRYOGENIC APPLICATIONS D.E.REFINED Fe-12Ni-0.25Ti STEEL FOR CRYOGENIC APPLICATIONS D.

  9. Air Pollution Control (Oklahoma)

    Broader source: Energy.gov [DOE]

    This chapter enumerates primary and secondary ambient air quality standards and the significant deterioration increments. Significant deterioration refers to an increase in ambient air pollution...

  10. Primary zone air proportioner

    DOE Patents [OSTI]

    Cleary, Edward N. G. (San Diego, CA)

    1982-10-12T23:59:59.000Z

    An air proportioner is provided for a liquid hydrocarbon fueled gas turbine of the type which is convertible to oil gas fuel and to coal gas fuel. The turbine includes a shell for enclosing the turbine, an air duct for venting air in said shell to a gasifier, and a fuel injector for injecting gasified fuel into the turbine. The air proportioner comprises a second air duct for venting air from the air duct for mixing with fuel from the gasifier. The air can be directly injected into the gas combustion basket along with the fuel from the injector or premixed with fuel from the gasifier prior to injection by the fuel injector.

  11. Air Tightness of US Homes: Model Development

    SciTech Connect (OSTI)

    Sherman, Max H.

    2006-05-01T23:59:59.000Z

    Air tightness is an important property of building envelopes. It is a key factor in determining infiltration and related wall-performance properties such as indoor air quality, maintainability and moisture balance. Air leakage in U.S. houses consumes roughly 1/3 of the HVAC energy but provides most of the ventilation used to control IAQ. The Lawrence Berkeley National Laboratory has been gathering residential air leakage data from many sources and now has a database of more than 100,000 raw measurements. This paper uses that database to develop a model for estimating air leakage as a function of climate, building age, floor area, building height, floor type, energy-efficiency and low-income designations. The model developed can be used to estimate the leakage distribution of populations of houses.

  12. Protein extraction in the refinement of Coastal Bermudagrass

    E-Print Network [OSTI]

    De La Rosa Perez, Luis Bernardo

    1992-01-01T23:59:59.000Z

    , phosphoric acid, gaseous hydrochloric acid, anhydrous ammonia and ethylendiamine (Chang et aL, 1981; Wylie and Steen, 1988). Also the use of organic solvents such as hexane or cadoxen ([Cd(ethylendiamine)3](OH)2, cadmium ethylendiamine) (Ladisch et al... and lignin. Integrated conversion of the entire "barrel of biomass" (also referred to as biomass refining), is essential to obtain good system economics. This study evaluated the use of the Ammonia Fiber Explosion (AFEX) process in an integrated conversion...

  13. EWO Mee'ng September 2012 Petrobras Refining Decision-Making Design

    E-Print Network [OSTI]

    Grossmann, Ignacio E.

    & Algorithm Thesis Prospectus Mathematical Modeling for Strategic and Investment Planning in the Oil-Refining Industry Brenno C. Menezes, Lincoln F. Moro Refining Op7miza7on PETROBRAS Petróleo SEWO Mee'ng ­ September 2012 Petrobras Refining Decision-Making Design Thesis Formulation

  14. Refinement and verification of concurrent systems specified in ObjectZ and CSP

    E-Print Network [OSTI]

    Smith, Graeme

    Refinement and verification of concurrent systems specified in Object­Z and CSP Graeme Smith­Z and CSP. A common semantic basis for the two languages enables a unified method of refinement to be used, based upon CSP refinement. To enable state­based techniques to be used for the Object­Z components

  15. Refined similarity hypotheses in shell models of turbulence

    E-Print Network [OSTI]

    Emily S. C. Ching; H. Guo; T. S. Lo

    2008-04-16T23:59:59.000Z

    A major challenge in turbulence research is to understand from first principles the origin of anomalous scaling of the velocity fluctuations in high-Reynolds-number turbulent flows. One important idea was proposed by Kolmogorov [J. Fluid Mech. {\\bf 13}, 82 (1962)], which attributes the anomaly to the variations of the locally averaged energy dissipation rate. Kraichnan later pointed out [J. Fluid Mech. {\\bf 62}, 305 (1973)] that the locally averaged energy dissipation rate is not an inertial-range quantity and a proper inertial-range quantity would be the local energy transfer rate. As a result, Kraichnan's idea attributes the anomaly to the variations of the local energy transfer rate. These ideas, generally known as refined similarity hypotheses, can also be extended to study the anomalous scaling of fluctuations of an active scalar, like the temperature in turbulent convection. In this paper, we examine the validity of these refined similarity hypotheses and their extensions to an active scalar in shell models of turbulence. We find that Kraichnan's refined similarity hypothesis and its extension are valid.

  16. CONSTRAINED-TRANSPORT MAGNETOHYDRODYNAMICS WITH ADAPTIVE MESH REFINEMENT IN CHARM

    SciTech Connect (OSTI)

    Miniati, Francesco [Physics Department, Wolfgang-Pauli-Strasse 27, ETH-Zuerich, CH-8093 Zuerich (Switzerland); Martin, Daniel F., E-mail: fm@phys.ethz.ch, E-mail: DFMartin@lbl.gov [Lawrence Berkeley National Laboratory, 1 Cyclotron Road, Berkeley, CA 94720 (United States)

    2011-07-01T23:59:59.000Z

    We present the implementation of a three-dimensional, second-order accurate Godunov-type algorithm for magnetohydrodynamics (MHD) in the adaptive-mesh-refinement (AMR) cosmological code CHARM. The algorithm is based on the full 12-solve spatially unsplit corner-transport-upwind (CTU) scheme. The fluid quantities are cell-centered and are updated using the piecewise-parabolic method (PPM), while the magnetic field variables are face-centered and are evolved through application of the Stokes theorem on cell edges via a constrained-transport (CT) method. The so-called multidimensional MHD source terms required in the predictor step for high-order accuracy are applied in a simplified form which reduces their complexity in three dimensions without loss of accuracy or robustness. The algorithm is implemented on an AMR framework which requires specific synchronization steps across refinement levels. These include face-centered restriction and prolongation operations and a reflux-curl operation, which maintains a solenoidal magnetic field across refinement boundaries. The code is tested against a large suite of test problems, including convergence tests in smooth flows, shock-tube tests, classical two- and three-dimensional MHD tests, a three-dimensional shock-cloud interaction problem, and the formation of a cluster of galaxies in a fully cosmological context. The magnetic field divergence is shown to remain negligible throughout.

  17. AiR surface: AiR surface 1

    E-Print Network [OSTI]

    Tanaka, Jiro

    AiR surface: 1 PDA AiR surface 1 1: AiR surface () () 2 [1] [2] 3 AiR surface AiR surface surface surface surface 3.1 surface [3]( 3 ) surface 3.2 surface surface AiR surface 4 AiR surface surface AiR surface: Virtual Touch Panel

  18. Air Pollution Spring 2010

    E-Print Network [OSTI]

    ATS 555 Air Pollution Spring 2010 T Th 11:00 ­ 12:15, NESB 101 Instructor: Prof. Sonia Kreidenweis an understanding of types and sources of air pollution. 2. Examine concentrations of air pollutants and their effects on health and welfare. Review regulations governing air pollution. 3. Examine the meteorological

  19. Exact results on ABJ theory and the refined topological string

    E-Print Network [OSTI]

    Masazumi Honda; Kazumi Okuyama

    2014-07-22T23:59:59.000Z

    We study the partition function of the ABJ theory, which is the N=6 superconformal Chern-Simons matter theory with gauge group U(N)xU(N+M) and Chern-Simons levels (k,-k). We exactly compute the ABJ partition function on a three sphere for various k, M and N via the Fermi gas approach. By using these exact data, we show that the ABJ partition function is completely determined by the refined topological string on local P^1 x P^1, including membrane instanton effects in the M-theory dual.

  20. Minimally refined biomass fuel. [carbohydrate-water-alcohol mixture

    SciTech Connect (OSTI)

    Pearson, R.K.; Hirschfeld, T.B.

    1981-03-26T23:59:59.000Z

    A minimally refined fluid composition, suitable as a fuel mixture and derived from biomass material, is comprised of one or more water-soluble carbohydrates such as sucrose, one or more alcohols having less than four carbons, and water. The carbohydrate provides the fuel source; water-solubilizes the carbohydrate; and the alcohol aids in the combustion of the carbohydrate and reduces the viscosity of the carbohydrate/water solution. Because less energy is required to obtain the carbohydrate from the raw biomass than alcohol, an overall energy savings is realized compared to fuels employing alcohol as the primary fuel.

  1. Changing Trends in the Refining Industry (released in AEO2006)

    Reports and Publications (EIA)

    2006-01-01T23:59:59.000Z

    There have been some major changes in the U.S. refining industry recently, prompted in part by a significant decline in the quality of imported crude oil and by increasing restrictions on the quality of finished products. As a result, high-quality crudes, such as the West Texas Intermediate (WTI) crude that serves as a benchmark for oil futures on the New York Mercantile Exchange (NYMEX), have been trading at record premiums to the OPEC (Organization of the Petroleum Exporting Countries) Basket price.

  2. REFINING PROGRAM HELPS REENERGIZE NEBRASKA UPGRADES | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page onYouTube YouTube Note: Since the.pdfBreakingMay 2015 < prevQuick Guide: Power PurchaseOwner's Role3REFINING PROGRAM

  3. Refining Bio-Oil alongside Petroleum | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page onYouTube YouTube Note: Since the.pdfBreakingMay 2015 < prevQuick Guide:U.N.JuneAs part of itsRefining Bio-Oil

  4. ITP Petroleum Refining: Petroleum Technology Vision 2020 | Department of

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels DataDepartment of Energy Your Density Isn't YourTransport(Fact Sheet),Energy Petroleum Technology Vision 2020 ITP Petroleum Refining:

  5. air temperature air: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    air temperatures... conditions. The design of this study was based on the relation- ship of four parameters: air temperature, air velocity, radiant heat, and globe...

  6. Interaction between Titles 2 and 3 of the Clean Air Act as amended, 1990

    SciTech Connect (OSTI)

    Szpunar, C.B.

    1996-02-01T23:59:59.000Z

    This report examines Some issues that would I affect the refining industry if the requirements for hazardous air pollutants set out in Title III of the Clean Air Act Amendments were to impede the market entrance of oxygenated fuels, as me; required by Title II. It describes the mandate for reformulated gasoline; considers gasoline characteristics in light of component shifts in refining; examines the supply of, demand for, and cost of various feedstocks and blendstocks; and identifies the emissions and atmospheric impacts that might result from the production and use of reformulated gasoline. Attention is focused on methanol and MTBE, two potential blendstocks that are also hazardous air pollutants, and on maximum achievable control technology standards, which might be applied to the stationary sources that produce them.

  7. California refiners move smoothly into next phase of RFG

    SciTech Connect (OSTI)

    Schaffer, S. [ed.

    1996-05-01T23:59:59.000Z

    The California RFG program (CARB RFG) began at the refinery level in March, the terminal level in April and will begin being enforced at the retail level June 1. By all accounts, early implementation is proceeding smoothly, with prices for both gasoline and oxygenates remaining fairly steady. Analysts labeled the introduction of the world`s cleanest gasoline {open_quotes}a non-event{close_quotes}. By April 1, more than half of the retail gasoline stations in California had fully complying CARB RFG. With cumulative investments of more than $3 billion, California`s refiners will be looking to recapture as much of the cost in the marketplace as possible. The incremental cost of CARB RFG production over federal RFG is estimated by refiners to be about 10{cents}/gal, mainly due to the capital investments needed for hydrotreating to reduce sulfur levels. Early batches of fuel on the spot market sold for about 8{cents}/gal over conventional prices, about 4.5{cents}/gal above federal RFG, according to the Oil Price Information Service (OPIS).

  8. A refined model for characterizing x-ray multilayers

    SciTech Connect (OSTI)

    Oren, A.L.; Henke, B.L.

    1987-12-01T23:59:59.000Z

    The ability to quickly and accurately characterize arbitrary multilayers is very valuable for not only can we use the characterizations to predict the reflectivity of a multilayer for any soft x-ray wavelength, we also can generalize the results to apply to other multilayers of the same type. In addition, we can use the characterizations as a means of evaluating various sputtering environments and refining sputtering techniques to obtain better multilayers. In this report we have obtained improved characterizations for sample molybdenum-silicon and vanadium-silicon multilayers. However, we only examined five crystals overall, so the conclusions that we could draw about the structure of general multilayers is limited. Research involving many multilayers manufactured under the same sputtering conditions is clearly in order. In order to best understand multilayer structures it may be necessary to further refine our model, e.g., adopting a Gaussian form for the interface regions. With such improvements we can expect even better agreement with experimental values and continued concurrence with other characterization techniques. 18 refs., 30 figs., 7 tabs.

  9. General Air Permits (Louisiana)

    Broader source: Energy.gov [DOE]

    Any source, including a temporary source, which emits or has the potential to emit any air contaminant requires an air permit. Facilities with potential emissions less than 5 tons per year of any...

  10. Healthy Air Act (Maryland)

    Broader source: Energy.gov [DOE]

    The Maryland Healthy Air Act was developed with the purpose of bringing Maryland into attainment with the National Ambient Air Quality Standards (NAAQS) for ozone and fine particulate matter by the...

  11. Compressed Air Supply Efficiency 

    E-Print Network [OSTI]

    Joseph, B.

    2004-01-01T23:59:59.000Z

    COMPRESSED AIR SUPPLY EFFICENCY Babu Joseph, Ph.D., P.E. Engineer Southern California Edison Irwindale, CA ABSTRACT This project, under contract from California Energy Commission, developed the CASE (Compressed Air Supply Efficiency...

  12. Third-Party Evaluation of Petro Tex Hydrocarbons, LLC, ReGen Lubricating Oil Re-refining Process

    SciTech Connect (OSTI)

    Compere, A L [ORNL; Griffith, William {Bill} L [ORNL

    2009-04-01T23:59:59.000Z

    This report presents an assessment of market, energy impact, and utility of the PetroTex Hydrocarbons, LLC., ReGen process for re-refining used lubricating oil to produce Group I, II, and III base oils, diesel fuel, and asphalt. PetroTex Hydrocarbons, LLC., has performed extensive pilot scale evaluations, computer simulations, and market studies of this process and is presently evaluating construction of a 23 million gallon per year industrial-scale plant. PetroTex has obtained a 30 acre site in the Texas Industries RailPark in Midlothian Texas. The environmental and civil engineering assessments of the site are completed, and the company has been granted a special use permit from the City of Midlothian and air emissions permits for the Texas Commission on Environmental Quality.

  13. SPCDC: A user-friendly computational tool for the design and refinement of practical pulse combustion systems

    SciTech Connect (OSTI)

    Barr, P.K.; Keller, J.O. [Sandia National Labs., Albuquerque, NM (United States); Kezerle, J.A. [Gas Research Institute (United States)

    1995-07-01T23:59:59.000Z

    This paper reports on the development and use of a user-friendly, PC-executable computer code that can assist engineers in designing pulse combustors for specific applications and in refining existing units. This code represents the culmination of over 10 years of research and development in the field of pulse combustion. The Sandia Pulse Combustor Design Code, or SPCDC, couples both the fuel-air injection and the energy release to the time-varying pressure wave. Because the injection and combustion processes both drive and are driven by the wave dynamics, this model couples the major processes that occur in a pulse combustor. SPCDC can supplement the time-proven method of actually building and testing a prototype unit, and significantly reduce the number of units that must be tested. It will help produce a superior pulse combustion system tailored to a specific application and should help widen the range of successful applications.

  14. on man, nature & air pollution

    E-Print Network [OSTI]

    Finlayson-Pitts, Barbara J

    2008-01-01T23:59:59.000Z

    on man, nature & air pollution About three decades ago, itand episodes of air pollution the following summer. Wetthe increase in air pollution. This hypothesis generated

  15. Ventilation Air Preconditioning Systems

    E-Print Network [OSTI]

    Khattar, M.; Brandemuehl, M. J.

    1996-01-01T23:59:59.000Z

    simply and cost-effectively with a dual path arrangement that treats and controls the ventilation air independently of the recirculation air. The Electric Power Research Institute (EPRI)--the nonprofit R&D arm of the electric utility industry... particular type of application. EPRI is developing variations of the dual path concept to meet different reeofit and new construction markets. Figure 6. Ventilation Air Conditioner as a Separate Unit EPRVCALMAC System: Separate Unit for Ventilation Air...

  16. MAD-AIR

    E-Print Network [OSTI]

    Tooley, J. J.; Moyer, N. A.

    1989-01-01T23:59:59.000Z

    with stress- related illness rather than the anwr that spells RELIEF. Air flow in, through ad arourd a house is an important concern in the building we call haw. !lb enhance air flow and change the various corditions or properties of the air, a variety...

  17. Air Quality Chapter Outline

    E-Print Network [OSTI]

    Wechsler, Risa H.

    Chapter 30 Air Quality Chapter Outline 1 Overview 2 1.1 Hazards / Impacts 2 1.2 Exposure Sources 3 Manual Chapter 30: Air Quality 7 References 20 8 Implementation 21 9 Ownership 22 1 Overview SLAC operations produce a wide range of air emissions. Sources of emissions include standard equipment

  18. Influence of Alloy and Solidification Parameters on Grain Refinement in Aluminum Weld Metal due to Inoculation

    SciTech Connect (OSTI)

    Schempp, Philipp [BAM, Germany; Tang, Z. [BIAS, Germany; Cross, Carl E. [Los Alamos National Laboratory; Seefeld, T. [BIAS, Germany; Pittner, A. [BAM, Germany; Rethmeier, M. [BAM, Germany

    2012-06-28T23:59:59.000Z

    The goals are: (1) Establish how much Ti/B grain refiner is need to completely refine aluminum weld metal for different alloys and different welding conditions; (2) Characterize how alloy composition and solidification parameters affect weld metal grain refinement; and (3) Apply relevant theory to understand observed behavior. Conclusions are: (1) additions of Ti/B grain refiner to weld metal in Alloys 1050, 5083, and 6082 resulted in significant grain refinement; (2) grain refinement was more effective in GTAW than LBW, resulting in finer grains at lower Ti content - reason is limited time available for equiaxed grain growth in LBW (inability to occlude columnar grain growth); (3) welding travel speed did not markedly affect grain size within GTAW and LBW clusters; and (4) application of Hunt CET analysis showed experimental G to be on the order of the critical G{sub CET}; G{sub CET} was consistently higher for GTAW than for LBW.

  19. Air Handling Unit Supply Air Temperature Optimization During Economizer Cycles

    E-Print Network [OSTI]

    Xu, K.; Liu, M.; Wang, G.; Wang, Z.

    2007-01-01T23:59:59.000Z

    temperature at supply air temperature setpoint. Mechanical cooling is always required when outside air temperature is higher than the supply air temperature setpoint. Generally the supply air temperature setpoint is set at 55°F for space humidity control...

  20. Impact of Environmental Compliance Costs on U.S. Refining Profitability 1995-2001

    Reports and Publications (EIA)

    2003-01-01T23:59:59.000Z

    This report assesses the effects of pollution abatement requirements on the financial performance of U.S. petroleum refining and marketing operations during the 1995 to 2001 period. This study is a follow-up to the October 1997 publication entitled The Impact of Environmental Compliance Costs on U.S. Refining Profitability, that focused on the financial impacts of U.S. refining pollution abatement investment requirements in the 1988 to1995 period.

  1. Bayesian latent variable modelling in studies of air pollution and health

    E-Print Network [OSTI]

    Burton, Geoffrey R.

    Bayesian latent variable modelling in studies of air pollution and health Duncan Lee, Gavin://www.bath.ac.uk/math-sci/BICS #12;Bayesian latent variable modelling in studies of air pollution and health. Duncan Lee (1), Gavin to air pollution on respiratory mortality in the elderly (aged 65 and above) in London, England, between

  2. Table 7. U.S. Refiner Motor Gasoline Volumes by Grade and Sales...

    U.S. Energy Information Administration (EIA) Indexed Site

    Information Administration Petroleum Marketing Annual 1995 Table 7. U.S. Refiner Motor Gasoline Volumes by Grade and Sales Type (Million Gallons per Day) - Continued Year...

  3. Table A1. Refiner/Reseller Motor Gasoline Prices by Grade, PAD...

    U.S. Energy Information Administration (EIA) Indexed Site

    AdministrationPetroleum Marketing Annual 1999 401 Table A1. RefinerReseller Motor Gasoline Prices by Grade, PAD District and State, 1984-Present (Cents per Gallon...

  4. Table A1. Refiner/Reseller Motor Gasoline Prices by Grade, PAD...

    Annual Energy Outlook 2013 [U.S. Energy Information Administration (EIA)]

    Information Administration Petroleum Marketing Annual 1995 Table A1. RefinerReseller Motor Gasoline Prices by Grade, PAD District and State, 1984-Present (Cents per Gallon...

  5. Table 6. U.S. Refiner Motor Gasoline Prices by Grade and Sales...

    U.S. Energy Information Administration (EIA) Indexed Site

    Energy Information AdministrationPetroleum Marketing Annual 1999 Table 6. U.S. Refiner Motor Gasoline Prices by Grade and Sales Type (Cents per Gallon Excluding Taxes) - Continued...

  6. Table 10. U.S. Refiner Oxygenated Motor Gasoline Prices by...

    U.S. Energy Information Administration (EIA) Indexed Site

    AdministrationPetroleum Marketing Annual 1999 Table 10. U.S. Refiner Oxygenated Motor Gasoline Prices by Grade and Sales Type (Cents per Gallon Excluding Taxes) Year Month...

  7. Table 6. U.S. Refiner Motor Gasoline Prices by Grade and Sales...

    U.S. Energy Information Administration (EIA) Indexed Site

    Energy Information AdministrationPetroleum Marketing Annual 1998 Table 6. U.S. Refiner Motor Gasoline Prices by Grade and Sales Type (Cents per Gallon Excluding Taxes) - Continued...

  8. Table 7. U.S. Refiner Motor Gasoline Volumes by Grade and Sales...

    U.S. Energy Information Administration (EIA) Indexed Site

    Energy Information AdministrationPetroleum Marketing Annual 1998 Table 7. U.S. Refiner Motor Gasoline Volumes by Grade and Sales Type (Million Gallons per Day) - Continued Year...

  9. Table 6. U.S. Refiner Motor Gasoline Prices by Grade and Sales...

    U.S. Energy Information Administration (EIA) Indexed Site

    Information Administration Petroleum Marketing Annual 1995 Table 6. U.S. Refiner Motor Gasoline Prices by Grade and Sales Type (Cents per Gallon Excluding Taxes) - Continued...

  10. Table 2. U.S. Refiner Prices of Petroleum Products to End Users

    U.S. Energy Information Administration (EIA) Indexed Site

    fuel. Note: Motor gasoline averages and totals prior to October 1993 include leaded gasoline. Sources: Energy Information Administration Form EIA-782A, "Refiners'Gas Plant...

  11. RFA-14-0001 - In the Matter of Commonwealth Oil Refining Company...

    Broader source: Energy.gov (indexed) [DOE]

    both programs would reduce the dependence of Puerto Rican consumers on high cost imported oil and refined petroleum products and that, consequently, both programs were consistent...

  12. Refining and Extending the Business Model with Information Technology: Dell Computer Corporation

    E-Print Network [OSTI]

    Kraemer, Kenneth L; Dedrick, Jason; Yamashiro, Sandra

    1999-01-01T23:59:59.000Z

    of Dell’s Direct Business Model Fuels Fifteenth ConsecutiveAND EXTENDING THE REFINING AND EXTENDING THE BUSINESS MODELBUSINESS MODEL CENTER FOR RESEARCH ON INFORMATION TECHNOLOGY

  13. OPERATOR INTERACTION WITH MODEL-BASED PREDICTIVE CONTROLLERS IN PETROCHEMICAL REFINING

    E-Print Network [OSTI]

    Virginia, University of

    OPERATOR INTERACTION WITH MODEL-BASED PREDICTIVE CONTROLLERS IN PETROCHEMICAL REFINING Greg A success in the petrochemical industry, they have introduced new challenges for the operators and engineers

  14. Table A2. Refiner/Reseller Prices of Aviation Fuels, Propane...

    Gasoline and Diesel Fuel Update (EIA)

    Marketing Annual 1999 421 Table A2. RefinerReseller Prices of Aviation Fuels, Propane, and Kerosene, by PAD District, 1983-Present (Cents per Gallon Excluding Taxes) -...

  15. Table A2. Refiner/Reseller Prices of Aviation Fuels, Propane...

    Annual Energy Outlook 2013 [U.S. Energy Information Administration (EIA)]

    Marketing Annual 1995 467 Table A2. RefinerReseller Prices of Aviation Fuels, Propane, and Kerosene, by PAD District, 1983-Present (Cents per Gallon Excluding Taxes) -...

  16. Quantitative Methods for Strategic and Investment Planning in the Oil-Refining

    E-Print Network [OSTI]

    Grossmann, Ignacio E.

    by one refinery Refinery Opera*onal Planning - Simulate the Refining Scenarios Supply Chain Investments Planning - Test the refinery best scenarios

  17. Table 46. Refiner No. 2 Distillate, Diesel Fuel, and Fuel Oil...

    Gasoline and Diesel Fuel Update (EIA)

    Petroleum Marketing Annual 1998 295 Table 46. Refiner No. 2 Distillate, Diesel Fuel, and Fuel Oil Volumes by PAD District and State (Thousand Gallons per Day) - Continued...

  18. Table 46. Refiner No. 2 Distillate, Diesel Fuel, and Fuel Oil...

    Gasoline and Diesel Fuel Update (EIA)

    Petroleum Marketing Annual 1995 337 Table 46. Refiner No. 2 Distillate, Diesel Fuel, and Fuel Oil Volumes by PAD District and State (Thousand Gallons per Day) - Continued...

  19. Table 46. Refiner No. 2 Distillate, Diesel Fuel, and Fuel Oil...

    U.S. Energy Information Administration (EIA) Indexed Site

    Petroleum Marketing Annual 1999 295 Table 46. Refiner No. 2 Distillate, Diesel Fuel, and Fuel Oil Volumes by PAD District and State (Thousand Gallons per Day) - Continued...

  20. Table A3. Refiner/Reseller Prices of Distillate and Residual...

    Annual Energy Outlook 2013 [U.S. Energy Information Administration (EIA)]

    Marketing Annual 1999 441 Table A3. RefinerReseller Prices of Distillate and Residual Fuel Oils, by PAD District, 1983-Present (Cents per Gallon Excluding Taxes) - Continued...

  1. Table 12. U.S. Refiner Reformulated Motor Gasoline Prices by...

    U.S. Energy Information Administration (EIA) Indexed Site

    Administration Petroleum Marketing Annual 1995 Table 12. U.S. Refiner Reformulated Motor Gasoline Prices by Grade and Sales Type (Cents per Gallon Excluding Taxes) - Continued...

  2. Table 10. U.S. Refiner Oxygenated Motor Gasoline Prices by...

    U.S. Energy Information Administration (EIA) Indexed Site

    Administration Petroleum Marketing Annual 1995 Table 10. U.S. Refiner Oxygenated Motor Gasoline Prices by Grade and Sales Type (Cents per Gallon Excluding Taxes) - Continued...

  3. Table 11. U.S. Refiner Oxygenated Motor Gasoline Volumes by...

    U.S. Energy Information Administration (EIA) Indexed Site

    Administration Petroleum Marketing Annual 1995 Table 11. U.S. Refiner Oxygenated Motor Gasoline Volumes by Grade and Sales Type (Million Gallons per Day) - Continued Year...

  4. Air to Air Communication Protocol Arjan Durresi1

    E-Print Network [OSTI]

    Jain, Raj

    1 Air to Air Communication Protocol Arjan Durresi1 , Vamsi Paruchuri1 , Leonard Barolli2 and Raj. Louis, MO 63130, USA 314-935-4963, jain@cse.wustl.edu Abstract--We present Air to Air Communication (AAC........................................................2 3. AIR TO AIR COMMUNICATION..............................3 4. SIMULATIONS

  5. Air Pollution- Local Air Quality (Ontario, Canada)

    Broader source: Energy.gov [DOE]

    The Air Pollution regulation administered by the Ministry of the Environment enforces compliance to the standards set in the Ontario law. The law is phased in, with portions taking effect in 2010,...

  6. ORIGINAL ARTICLE Ambient Air Pollution

    E-Print Network [OSTI]

    Mulholland, James A.

    ORIGINAL ARTICLE Ambient Air Pollution and Cardiovascular Emergency Department Visits Kristi Busico ambient air pollutants and cardiovascular disease (CVD), the roles of the physicochemical components the relation between ambient air pollution and cardiovascular conditions using ambient air quality data

  7. ENZO: AN ADAPTIVE MESH REFINEMENT CODE FOR ASTROPHYSICS

    SciTech Connect (OSTI)

    Bryan, Greg L.; Turk, Matthew J. [Columbia University, Department of Astronomy, New York, NY 10025 (United States); Norman, Michael L.; Bordner, James; Xu, Hao; Kritsuk, Alexei G. [CASS, University of California, San Diego, 9500 Gilman Drive La Jolla, CA 92093-0424 (United States); O'Shea, Brian W.; Smith, Britton [Department of Physics and Astronomy, Michigan State University, East Lansing, MI 48824 (United States); Abel, Tom; Wang, Peng; Skillman, Samuel W. [Kavli Institute for Particle Astrophysics and Cosmology, Stanford University, Menlo Park, CA 94025 (United States); Wise, John H. [Center for Relativistic Astrophysics, School of Physics, Georgia Institute of Technology, 837 State Street, Atlanta, GA (United States); Reynolds, Daniel R. [Department of Mathematics, Southern Methodist University, Box 750156, Dallas, TX 75205-0156 (United States); Collins, David C. [Department of Physics, Florida State University, Tallahassee, FL 32306 (United States); Harkness, Robert P. [NICS, Oak Ridge National Laboratory, 1 Bethel Valley Rd, Oak Ridge, TN 37831 (United States); Kim, Ji-hoon [Department of Astronomy and Astrophysics, University of California, 1156 High Street, Santa Cruz, CA 95064 (United States); Kuhlen, Michael [Theoretical Astrophysics Center, University of California Berkeley, Hearst Field Annex, Berkeley, CA 94720 (United States); Goldbaum, Nathan [Institute for Astronomy, University of Edinburgh, Edinburgh EH9 3HJ (United Kingdom); Hummels, Cameron [Department of Astronomy/Steward Observatory, University of Arizona, 933 N. Cherry Ave., Tucson, AZ 85721 (United States); Tasker, Elizabeth [Physics Department, Faculty of Science, Hokkaido University, Kita-10 Nishi 8, Kita-ku, Sapporo 060-0810 (Japan); Collaboration: Enzo Collaboration; and others

    2014-04-01T23:59:59.000Z

    This paper describes the open-source code Enzo, which uses block-structured adaptive mesh refinement to provide high spatial and temporal resolution for modeling astrophysical fluid flows. The code is Cartesian, can be run in one, two, and three dimensions, and supports a wide variety of physics including hydrodynamics, ideal and non-ideal magnetohydrodynamics, N-body dynamics (and, more broadly, self-gravity of fluids and particles), primordial gas chemistry, optically thin radiative cooling of primordial and metal-enriched plasmas (as well as some optically-thick cooling models), radiation transport, cosmological expansion, and models for star formation and feedback in a cosmological context. In addition to explaining the algorithms implemented, we present solutions for a wide range of test problems, demonstrate the code's parallel performance, and discuss the Enzo collaboration's code development methodology.

  8. Refining and classifying finite-time Lyapunov exponent ridges

    E-Print Network [OSTI]

    Allshouse, Michael R

    2015-01-01T23:59:59.000Z

    While more rigorous and sophisticated methods for identifying Lagrangian based coherent structures exist, the finite-time Lyapunov exponent (FTLE) field remains a straightforward and popular method for gaining some insight into transport by complex, time-dependent two-dimensional flows. In light of its enduring appeal, and in support of good practice, we begin by investigating the effects of discretization and noise on two numerical approaches for calculating the FTLE field. A practical method to extract and refine FTLE ridges in two-dimensional flows, which builds on previous methods, is then presented. Seeking to better ascertain the role of an FTLE ridge in flow transport, we adapt an existing classification scheme and provide a thorough treatment of the challenges of classifying the types of deformation represented by an FTLE ridge. As a practical demonstration, the methods are applied to an ocean surface velocity field data set generated by a numerical model.

  9. Fuel and oxygen addition for metal smelting or refining process

    DOE Patents [OSTI]

    Schlichting, M.R.

    1994-11-22T23:59:59.000Z

    A furnace for smelting iron ore and/or refining molten iron is equipped with an overhead pneumatic lance, through which a center stream of particulate coal is ejected at high velocity into a slag layer. An annular stream of nitrogen or argon enshrouds the coal stream. Oxygen is simultaneously ejected in an annular stream encircling the inert gas stream. The interposition of the inert gas stream between the coal and oxygen streams prevents the volatile matter in the coal from combusting before it reaches the slag layer. Heat of combustion is thus more efficiently delivered to the slag, where it is needed to sustain the desired reactions occurring there. A second stream of lower velocity oxygen can be delivered through an outermost annulus to react with carbon monoxide gas rising from slag layer, thereby adding still more heat to the furnace. 7 figs.

  10. Passive Room-to-Room Air Transfer, Fresno, California (Fact Sheet)

    SciTech Connect (OSTI)

    Not Available

    2014-02-01T23:59:59.000Z

    Field testing was performed in a retrofit unoccupied test house in Fresno, California. Three air-based heating, ventilation, and air conditioning (HVAC) distribution systems - a typical airflow ducted system to the bedrooms, a low airflow ducted system to the bedrooms, and a system with no ductwork to the bedrooms - were evaluated during heating, cooling, and midseason conditions. The relative ability of each of the three systems was assessed with respect to relevant Air Conditioning Contractors of America (ACCA) and ASHRAE standards for house temperature uniformity and stability, respectively. Computational fluid dynamics (CFD) modeling also was performed and refined based on comparison to field test results to determine the air flow rate into the bedrooms of over-door and bottom-of-door air transfer grilles.

  11. Wavelet Bi-frames with few Generators from Multivariate Refinable Functions

    E-Print Network [OSTI]

    Ehler, Martin

    Wavelet Bi-frames with few Generators from Multivariate Refinable Functions Martin Ehler Bin Han compactly supported wavelet bi-frames with few generators from almost any pair of compactly sup- ported multivariate refinable functions. In our examples, we focus on wavelet bi-frames whose primal and dual wavelets

  12. Refining k-means by Bootstrap and Data Depth Aurora Torrente and Juan Romo

    E-Print Network [OSTI]

    Romo, Juan

    Refining k-means by Bootstrap and Data Depth Aurora Torrente and Juan Romo Departamento de Estad two simple, computationally fast methods that allow the refinement of the initial points of k-means to cluster a given data set. They are based on alternating k-means and the search of the deepest (most

  13. Rapidly-Exploring Roadmaps: Weighing Exploration vs. Refinement in Optimal Motion Planning

    E-Print Network [OSTI]

    North Carolina at Chapel Hill, University of

    Rapidly-Exploring Roadmaps: Weighing Exploration vs. Refinement in Optimal Motion Planning Ron of already explored regions to find better paths. We present the rapidly- exploring roadmap (RRM), a new to explore further or to refine the explored space by adding edges to the current roadmap to find higher

  14. To appear in EPTCS. A CSP account of Event-B refinement

    E-Print Network [OSTI]

    Doran, Simon J.

    To appear in EPTCS. A CSP account of Event-B refinement Steve Schneider Department of Computing a CSP account of Event-B refinement, with a treatment for the first time of splitting events and of anticipated events. To this end, we define a CSP seman- tics for Event-B and show how the different forms

  15. FDR3 --A Modern Refinement Checker for CSP Thomas Gibson-Robinson, Philip Armstrong,

    E-Print Network [OSTI]

    Oxford, University of

    FDR3 -- A Modern Refinement Checker for CSP Thomas Gibson-Robinson, Philip Armstrong, Alexandre.roscoe}@cs.ox.ac.uk Abstract. FDR3 is a complete rewrite of the CSP refinement checker FDR2, incorporating a significant number describe the new algorithm that FDR3 uses to construct its internal representation of CSP processes

  16. FDR3 --A Modern Refinement Checker for CSP Thomas Gibson-Robinson, Philip Armstrong,

    E-Print Network [OSTI]

    Oxford, University of

    FDR3 -- A Modern Refinement Checker for CSP Thomas Gibson-Robinson, Philip Armstrong, Alexandre.roscoe}@cs.ox.ac.uk Abstract. FDR3 is a complete rewrite of the CSP refinement checker FDR2, incorporating a significant number describe the new algorithm that FDR3 uses to construct its in- ternal representation of CSP processes

  17. Don't care in SMT--Building flexible yet efficient abstraction/refinement solvers

    E-Print Network [OSTI]

    Leucker, Martin

    Don't care in SMT--Building flexible yet efficient abstraction/refinement solvers Andreas Bauer Satisfiability Modulo Theories (SMT) solver for a wide range of theories. Our method follows the abstrac- tion/refinement approach to simplify the implementation of custom SMT solvers. The expected performance penalty

  18. Don't care in SMT---Building flexible yet efficient abstraction/refinement solvers

    E-Print Network [OSTI]

    Leucker, Martin

    Don't care in SMT---Building flexible yet efficient abstraction/refinement solvers Andreas Bauer an efficient Satisfiability Modulo Theories (SMT) solver for a wide range of theories. Our method follows the abstrac­ tion/refinement approach to simplify the implementation of custom SMT solvers. The expected

  19. Aspects of Western Refining, Inc.'s Proposed Acquisition of Giant Industries, Inc.

    Reports and Publications (EIA)

    2006-01-01T23:59:59.000Z

    Presentation of company-level, non-proprietary data and relevant aggregate data for U.S. refinery capacity and gasoline marketing of Western Refining and Giant Industries to inform discussions of Western Refining Inc.'s proposed acquisition of Giant Industries Inc. for a total of $1.5 billion, which was announced August 28, 2006.

  20. Air Pollution Control (Indiana)

    Broader source: Energy.gov [DOE]

    The mission of the Indiana Department of Environmental Management's Office of Air Quality implements federal and state regulations to protect human health and the environment while allowing the...

  1. Air Pollution Controls

    Broader source: Energy.gov [DOE]

    Various statutes within the Wisconsin Legislative Documents relate to air pollution control. These statutes describe zoning, permitting, and emissions regulations for hazardous and non-hazardous...

  2. Personal continuous air monitor

    DOE Patents [OSTI]

    Morgan, Ronald G. (Los Alamos, NM); Salazar, Samuel A. (Albuquerque, NM)

    2000-01-01T23:59:59.000Z

    A personal continuous air monitor capable of giving immediate warning of the presence of radioactivity has a filter/detector head to be worn in the breathing zone of a user, containing a filter mounted adjacent to radiation detectors, and a preamplifier. The filter/detector head is connected to a belt pack to be worn at the waist or on the back of a user. The belt pack contains a signal processor, batteries, a multichannel analyzer, a logic circuit, and an alarm. An air pump also is provided in the belt pack for pulling air through the filter/detector head by way of an air tube.

  3. Environmental Quality: Air (Louisiana)

    Broader source: Energy.gov [DOE]

    The Department of Environmental Quality regulates air quality in Louisiana. The Department has an established a fee system for funding the monitoring, investigation and other activities required...

  4. AIR SEALING Seal air leaks and save energy!

    E-Print Network [OSTI]

    Oak Ridge National Laboratory

    AIR SEALING Seal air leaks and save energy! W H A T I S A I R L E A K A G E ? Ventilation is fresh air that enters a house in a controlled manner to exhaust excess moisture and reduce odors and stuffiness. Air leakage, or infiltration, is outside air that enters a house uncontrollably through cracks

  5. Air Quality: Air Pollutants, SLAC Emissions Sources, and Regulatory Reference

    E-Print Network [OSTI]

    Wechsler, Risa H.

    Air Quality: Air Pollutants, SLAC Emissions Sources, and Regulatory Reference Department: Chemical and General Safety Program: Air Quality Owner: Program Manager Authority: ES&H Manual, Chapter 30, Air Quality1 SLAC's air emissions are regulated through a federally mandated site-wide permit as well

  6. Cosmos++: Relativistic Magnetohydrodynamics on Unstructured Grids with Local Adaptive Refinement

    E-Print Network [OSTI]

    Peter Anninos; P. Chris Fragile; Jay D. Salmonson

    2005-09-09T23:59:59.000Z

    A new code and methodology are introduced for solving the general relativistic magnetohydrodynamic (GRMHD) equations in fixed background spacetimes using time-explicit, finite-volume discretization. The code has options for solving the GRMHD equations using traditional artificial-viscosity (AV) or non-oscillatory central difference (NOCD) methods, or a new extended AV (eAV) scheme using artificial-viscosity together with a dual energy-flux-conserving formulation. The dual energy approach allows for accurate modeling of highly relativistic flows at boost factors well beyond what has been achieved to date by standard artificial viscosity methods. It provides the benefit of Godunov methods in capturing high Lorentz boosted flows but without complicated Riemann solvers, and the advantages of traditional artificial viscosity methods in their speed and flexibility. Additionally, the GRMHD equations are solved on an unstructured grid that supports local adaptive mesh refinement using a fully threaded oct-tree (in three dimensions) network to traverse the grid hierarchy across levels and immediate neighbors. A number of tests are presented to demonstrate robustness of the numerical algorithms and adaptive mesh framework over a wide spectrum of problems, boosts, and astrophysical applications, including relativistic shock tubes, shock collisions, magnetosonic shocks, Alfven wave propagation, blast waves, magnetized Bondi flow, and the magneto-rotational instability in Kerr black hole spacetimes.

  7. Compressed Air System Optimization

    E-Print Network [OSTI]

    Aegerter, R.

    Several years ago I went to a gas station and noticed that my car's tires were low on air. I saw the gas station had an air compressor, but it cost a quarter to use the compressor. I paid my quarter and used the compressor. I realized...

  8. Recirculating electric air filter

    DOE Patents [OSTI]

    Bergman, W.

    1985-01-09T23:59:59.000Z

    An electric air filter cartridge has a cylindrical inner high voltage electrode, a layer of filter material, and an outer ground electrode formed of a plurality of segments moveably connected together. The outer electrode can be easily opened to remove or insert filter material. Air flows through the two electrodes and the filter material and is exhausted from the center of the inner electrode.

  9. J4.3 LARGE-EDDY SIMULATION ACROSS A GRID REFINEMENT INTERFACE USING EXPLICIT FILTERING AND RECONSTRUCTION

    E-Print Network [OSTI]

    Chow, Fotini Katopodes

    reflect off grid refinement interfaces, specifically on the outflow boundary from a fine to a coarse grid reflection off grid refinement interfaces by forcing the filter-resolved scale on a fine grid to equal

  10. Aging of gaseous detectors

    SciTech Connect (OSTI)

    Va'Vra, J.

    1990-03-01T23:59:59.000Z

    This paper makes an overview of developments in the wire chamber aging field since the wire chamber aging workshop held at the Lawrence Berkeley Laboratory, Berkeley, California on January 16--17, 1986. The author discusses new techniques to analyze the gas impurities and the wire aging products, wire nonaging'' in clean systems, wire aging in systems containing various impurities, various examples of problems which can prime'' surfaces prior to the occurrence of the aging, and some recent aging experience with the SSC micro-straw tubes.'' 35 refs., 10 figs., 2 tabs.

  11. air volume air: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Air Preheat Economics Texas A&M University - TxSpace Summary: Retrofit air preheat systems are the most reliable and efficient means to effect significant energy...

  12. Abatement of Air Pollution: Hazardous Air Pollutants (Connecticut...

    Broader source: Energy.gov (indexed) [DOE]

    allowable stack concentrations and hazard limiting values for the emission of hazardous air pollutants. The regulations also discuss sampling procedures for hazardous air...

  13. Air Resources: Prevention and Control of Air Contamination and...

    Broader source: Energy.gov (indexed) [DOE]

    limits and permitting and operational requirements for facilities that may contribute to air emissions. General air quality standards and standards for specific contaminants are...

  14. Air Pollution Control Regulations: No. 7 - Emission of Air Contaminant...

    Broader source: Energy.gov (indexed) [DOE]

    with the enjoyment of life and property. The criteria for determining compliance is listed in the regulations, and is based on other air pollution and ambient air standards...

  15. Air ejector augmented compressed air energy storage system

    DOE Patents [OSTI]

    Ahrens, Frederick W. (Naperville, IL); Kartsounes, George T. (Naperville, IL)

    1980-01-01T23:59:59.000Z

    Energy is stored in slack demand periods by charging a plurality of underground reservoirs with air to the same peak storage pressure, during peak demand periods throttling the air from one storage reservoir into a gas turbine system at a constant inlet pressure until the air pressure in the reservoir falls to said constant inlet pressure, thereupon permitting air in a second reservoir to flow into said gas turbine system while drawing air from the first reservoir through a variable geometry air ejector and adjusting said variable geometry air ejector, said air flow being essentially at the constant inlet pressure of the gas turbine system.

  16. EVALUATION OF THE SACCHAROFLEX 2000 REFLECTANCE MEASURING INSTRUMENT FOR REFINED SUGAR COLOUR ESTIMATION AT HULETTS REFINERY

    E-Print Network [OSTI]

    M Moodley; N K Padayachee; V Govender

    Due to the successful use of the Saccharoflex 2000 reflectance measurement instrument on the estimation of refined sugar colour elsewhere in the world, it was decided by Tongaat-Hulett Sugar to evaluate the instrument at the refinery in Durban. Tests were carried out on first, second, third and fourth refined sugars, the results of which showed a good correlation between the ICUMSA colour measurement and the reflectance reading obtained from the Saccharoflex 2000. The instrument offers a number of advantages, the main one being that a refined sugar colour value can be obtained in less than a minute. The refinery has therefore purchased one for process control.

  17. Influence of Aluminum Content on Grain Refinement and Strength of AZ31 Magnesium GTA Weld Metal

    SciTech Connect (OSTI)

    Babu, N. Kishore [Singapore Institute of Manufacturing Technology; Cross, Carl E. [Los Alamos National Laboratory

    2012-06-28T23:59:59.000Z

    The goal is to characterize the effect of Al content on AZ31 weld metal, the grain size and strength, and examine role of Al on grain refinement. The approach is to systematically vary the aluminum content of AZ31 weld metal, Measure average grain size in weld metal, and Measure cross-weld tensile properties and hardness. Conclusions are that: (1) increased Al content in AZ31 weld metal results in grain refinement Reason: higher undercooling during solidification; (2) weld metal grain refinement resulted in increased strength & hardness Reason: grain boundary strengthening; and (3) weld metal strength can be raised to wrought base metal levels.

  18. RAM: a Relativistic Adaptive Mesh Refinement Hydrodynamics Code

    SciTech Connect (OSTI)

    Zhang, Wei-Qun; /KIPAC, Menlo Park; MacFadyen, Andrew I.; /Princeton, Inst. Advanced Study

    2005-06-06T23:59:59.000Z

    The authors have developed a new computer code, RAM, to solve the conservative equations of special relativistic hydrodynamics (SRHD) using adaptive mesh refinement (AMR) on parallel computers. They have implemented a characteristic-wise, finite difference, weighted essentially non-oscillatory (WENO) scheme using the full characteristic decomposition of the SRHD equations to achieve fifth-order accuracy in space. For time integration they use the method of lines with a third-order total variation diminishing (TVD) Runge-Kutta scheme. They have also implemented fourth and fifth order Runge-Kutta time integration schemes for comparison. The implementation of AMR and parallelization is based on the FLASH code. RAM is modular and includes the capability to easily swap hydrodynamics solvers, reconstruction methods and physics modules. In addition to WENO they have implemented a finite volume module with the piecewise parabolic method (PPM) for reconstruction and the modified Marquina approximate Riemann solver to work with TVD Runge-Kutta time integration. They examine the difficulty of accurately simulating shear flows in numerical relativistic hydrodynamics codes. They show that under-resolved simulations of simple test problems with transverse velocity components produce incorrect results and demonstrate the ability of RAM to correctly solve these problems. RAM has been tested in one, two and three dimensions and in Cartesian, cylindrical and spherical coordinates. they have demonstrated fifth-order accuracy for WENO in one and two dimensions and performed detailed comparison with other schemes for which they show significantly lower convergence rates. Extensive testing is presented demonstrating the ability of RAM to address challenging open questions in relativistic astrophysics.

  19. Renewables and air quality

    SciTech Connect (OSTI)

    Wooley, D.R.

    2000-08-01T23:59:59.000Z

    The US heavy reliance on fossil fuels is a central obstacle to improving air quality and preventing catastrophic climate change. To solve this problem will require a combination of financial incentives and market rules that strongly encourage development of renewable energy resources to meet electric power demand. One promising policy option is to allow renewable energy resources to directly participate in air pollution emission trading mechanisms. Currently, the clean air benefits of renewable energy generally go unrecognized by regulators, under-appreciated by consumers and uncompensated by markets. Renewable energy is a key clean air alternative to conventional electricity generation, and the development of renewables could be stimulated by changes to the Clean Air Act's emissions trading programs. As Congress revisits clean air issues over the next several years, renewable energy representatives could push for statutory changes that reward the renewable energy industry for the air quality benefits it provides. By also becoming involved in key US Environmental Protection Agency (EPA) and state rule-making cases, the renewables industry could influence the structure of emissions trading programs and strengthen one of the most persuasive arguments for wind, solar and biomass energy development.

  20. Texas Clean Air Act (Texas)

    Broader source: Energy.gov [DOE]

    This Act is designed to safeguard the state's air resources from pollution by requiring the control and abatement of air pollution and emissions of air contaminants, consistent with the protection...

  1. Air Quality (Nova Scotia, Canada)

    Broader source: Energy.gov [DOE]

    Nova Scotia Environment is responsible for monitoring the air quality in the province, as well as administering fines and permits relating to air quality. The Air Quality Regulations state...

  2. Health Hazards in Indoor Air

    E-Print Network [OSTI]

    Logue, Jennifer M.

    2012-01-01T23:59:59.000Z

    Health Hazards in Indoor Air. In Proceedings of the 2010for VOCs from post-1990 indoor air concentration studies inUnion project on indoor air pollutants. Allergy, 2008. 63(

  3. Making Compressed Air System Decisions

    E-Print Network [OSTI]

    Porri, R. E.

    . The design of a compressed air system was formerly limited to the selection of an air compressor large enough to deliver sufficient compressed air for the estimated system requirements. As system air requirements grew, additional compressors were added... specification, selection and installation process will follow. BACKGROUND For more than 100 years compressed air has been used throughout industry as a safe and reliable utility. The generation of this utility is performed by an air compressor. The first...

  4. Air heating system

    DOE Patents [OSTI]

    Primeau, John J. (19800 Seminole Rd., Euclid, OH 44117)

    1983-03-01T23:59:59.000Z

    A self-starting, fuel-fired, air heating system including a vapor generator, a turbine, and a condenser connected in a closed circuit such that the vapor output from the vapor generator is conducted to the turbine and then to the condenser where it is condensed for return to the vapor generator. The turbine drives an air blower which passes air over the condenser for cooling the condenser. Also, a condensate pump is driven by the turbine. The disclosure is particularly concerned with the provision of heat exchanger and circuitry for cooling the condensed fluid output from the pump prior to its return to the vapor generator.

  5. Air Cooling R&D

    Broader source: Energy.gov (indexed) [DOE]

    or otherwise restricted information. 2 State of the Art Everything on a vehicle is air cooled, ultimately... Air cooling can be done... When?... How? Honda Insight Power...

  6. Ambient Air Quality Standards (Iowa)

    Broader source: Energy.gov [DOE]

    These regulations set statewide ambient air quality standards for various contaminants. The state code follows the regulations set forth in the National Primary and Secondary Ambient Air Quality...

  7. Compressed Air Supply Efficiency

    E-Print Network [OSTI]

    Joseph, B.

    2004-01-01T23:59:59.000Z

    This project, under contract from California Energy Commission, developed the CASE (Compressed Air Supply Efficiency) Index as a stand-alone value for compressor central plant efficiency. This Index captures the overall efficiency of a compressed...

  8. Retrofit Air Preheat Economics

    E-Print Network [OSTI]

    Goolsbee, J. A.

    1981-01-01T23:59:59.000Z

    Retrofit air preheat systems are the most reliable and efficient means to effect significant energy conservation for large existing industrial furnaces. Units can be quickly installed without a lengthy shutdown, and the furnace efficiency can...

  9. Padding with Compressed Air

    E-Print Network [OSTI]

    Beals, C.

    2004-01-01T23:59:59.000Z

    We commonly find plants using padding to transport liquids or light solids short distances from tankers into storage tanks. Padding can wreck havoc in compressed air systems with limited storage, undersized cleanup equipment (dryers and filters...

  10. Canned Air in China

    E-Print Network [OSTI]

    Hacker, Randi

    2013-10-23T23:59:59.000Z

    Broadcast Transcript: Not that long ago, coal smoke made the air here in Beijing so caustic that your nasal passages were seared with each breath. Those were the good old days: Car ownership was limited to government ...

  11. Breathing zone air sampler

    SciTech Connect (OSTI)

    Tobin, John (Bethel Park, PA)

    1989-01-01T23:59:59.000Z

    A sampling apparatus is provided which comprises a sampler for sampling air in the breathing zone of a wearer of the apparatus and a support for the sampler preferably in the form of a pair of eyeglasses. The sampler comprises a sampling assembly supported on the frame of the eyeglasses and including a pair of sample transport tubes which are suspended, in use, centrally of the frame so as to be disposed on opposite sides of the nose of the wearer and which each include an inlet therein that, in use, is disposed adjacent to a respective nostril of the nose of the wearer. A filter holder connected to sample transport tubes supports a removable filter for filtering out particulate material in the air sampled by the apparatus. The sample apparatus is connected to a pump for drawing air into the apparatus through the tube inlets so that the air passes through the filter.

  12. Breathing zone air sampler

    SciTech Connect (OSTI)

    Tobin, J.

    1989-08-22T23:59:59.000Z

    A sampling apparatus is presented which comprises a sampler for sampling air in the breathing zone of a wearer of the apparatus and a support for the sampler preferably in the form of a pair of eyeglasses. The sampler comprises a sampling assembly supported on the frame of the eyeglasses and including a pair of sample transport tubes which are suspended, in use, centrally of the frame so as to be disposed on opposite sides of the nose of the wearer and which each include an inlet therein that, in use, is disposed adjacent to a respective nostril of the nose of the wearer. A filter holder connected to sample transport tubes supports a removable filter for filtering out particulate material in the air sampled by the apparatus. The sample apparatus is connected to a pump for drawing air into the apparatus through the tube inlets so that the air passes through the filter.

  13. Air pollution meteorology

    SciTech Connect (OSTI)

    Eagleman, J.R.

    1991-01-01T23:59:59.000Z

    Air Pollution Meteorology is divided into three parts: air pollution fundamentals; concentration calculations and distributions; and pollution and meteorological interactions. The first section includes chapters on the following topics: the problem; measurements, sources, and standards; air stagnation and pollutant index; and effects. The second section of the book includes chapters on diffusion theory, the Gaussian plume dispersion model, plume rise, various dispersion models, scale considerations, and concentration trends. The third and final section (on pollution and meteorological interactions) begins with two chapters on radiative and wind effects on dispersion, and then follows with chapters on acid rain, the ozone hole, the greenhouse effect, and nuclear winter. In summary, Air Pollution Meteorology does a good job of covering the field for physics, chemistry, and engineering students who want to obtain an overview of the subject.

  14. Air conditioning system

    DOE Patents [OSTI]

    Lowenstein, Andrew; Miller, Jeffrey; Gruendeman, Peter; DaSilva, Michael

    2005-02-01T23:59:59.000Z

    An air conditioner comprises a plurality of plates arranged in a successively stacked configuration with portions thereof having a spaced apart arrangement, and defining between successive adjacent pairs of plates at the spaced apart portions a first and second series of discrete alternating passages wherein a first air stream is passed through the first series of passages and a second air stream is passed through the second series of passages; and said stacked configuration of plates forming integrally therewith a liquid delivery means for delivering from a source a sufficient quantity of a liquid to the inside surfaces of the first series of fluid passages in a manner which provides a continuous flow of the liquid from a first end to a second end of the plurality of plates while in contact with the first air stream.

  15. Air bag restraint device

    DOE Patents [OSTI]

    Marts, D.J.; Richardson, J.G.

    1995-10-17T23:59:59.000Z

    A rear-seat air bag restraint device is disclosed that prevents an individual, or individuals, from continuing violent actions while being transported in a patrol vehicle`s rear seat without requiring immediate physical contact by the law enforcement officer. The air bag is activated by a control switch in the front seat and inflates to independently restrict the amount of physical activity occurring in the rear seat of the vehicle while allowing the officer to safely stop the vehicle. The air bag can also provide the officer additional time to get backup personnel to aid him if the situation warrants it. The bag is inflated and maintains a constant pressure by an air pump. 8 figs.

  16. Table 9. U.S. Refiner Conventional Motor Gasoline Volumes by...

    U.S. Energy Information Administration (EIA) Indexed Site

    5.7 5.9 4.4 12.9 NA 17.3 See footnotes at end of table. 9. U.S. Refiner Conventional Motor Gasoline Volumes by Grade and Sales Type 18 Energy Information Administration ...

  17. Table 10. U.S. Refiner Oxygenated Motor Gasoline Prices by...

    U.S. Energy Information Administration (EIA) Indexed Site

    98.0 98.0 86.6 75.0 - 80.1 See footnotes at end of table. 10. U.S. Refiner Oxygenated Motor Gasoline Prices by Grade and Sales Type 20 Energy Information Administration ...

  18. Table 13. U.S. Refiner Reformulated Motor Gasoline Volumes by...

    U.S. Energy Information Administration (EIA) Indexed Site

    3.3 3.4 7.9 3.3 W 11.3 See footnotes at end of table. 13. U.S. Refiner Reformulated Motor Gasoline Volumes by Grade and Sales Type 26 Energy Information Administration ...

  19. Table 12. U.S. Refiner Reformulated Motor Gasoline Prices by...

    U.S. Energy Information Administration (EIA) Indexed Site

    92.4 92.1 83.7 74.1 W 80.9 See footnotes at end of table. 12. U.S. Refiner Reformulated Motor Gasoline Prices by Grade and Sales Type 24 Energy Information Administration ...

  20. Table 8. U.S. Refiner Conventional Motor Gasoline Prices by...

    U.S. Energy Information Administration (EIA) Indexed Site

    87.4 86.9 78.3 68.5 W 70.8 See footnotes at end of table. 8. U.S. Refiner Conventional Motor Gasoline Prices by Grade and Sales Type 16 Energy Information Administration ...

  1. Table 12. U.S. Refiner Reformulated Motor Gasoline Prices by...

    U.S. Energy Information Administration (EIA) Indexed Site

    92.8 92.5 84.0 72.5 W 80.7 See footnotes at end of table. 12. U.S. Refiner Reformulated Motor Gasoline Prices by Grade and Sales Type 24 Energy Information Administration ...

  2. Table 8. U.S. Refiner Conventional Motor Gasoline Prices by...

    U.S. Energy Information Administration (EIA) Indexed Site

    88.4 87.8 80.1 70.0 NA 72.6 See footnotes at end of table. 8. U.S. Refiner Conventional Motor Gasoline Prices by Grade and Sales Type 16 Energy Information Administration ...

  3. Table 10. U.S. Refiner Oxygenated Motor Gasoline Prices by...

    U.S. Energy Information Administration (EIA) Indexed Site

    94.0 93.9 83.2 73.8 - 79.3 See footnotes at end of table. 10. U.S. Refiner Oxygenated Motor Gasoline Prices by Grade and Sales Type 20 Energy Information Administration ...

  4. Table 13. U.S. Refiner Reformulated Motor Gasoline Volumes by...

    U.S. Energy Information Administration (EIA) Indexed Site

    3.6 3.7 7.9 3.1 W 11.0 See footnotes at end of table. 13. U.S. Refiner Reformulated Motor Gasoline Volumes by Grade and Sales Type 26 Energy Information Administration ...

  5. Table 9. U.S. Refiner Conventional Motor Gasoline Volumes by...

    U.S. Energy Information Administration (EIA) Indexed Site

    5.7 5.9 3.9 12.7 W 16.6 See footnotes at end of table. 9. U.S. Refiner Conventional Motor Gasoline Volumes by Grade and Sales Type 18 Energy Information Administration ...

  6. Process for solvent refining of coal using a denitrogenated and dephenolated solvent

    DOE Patents [OSTI]

    Garg, Diwakar (Macungie, PA); Givens, Edwin N. (Bethlehem, PA); Schweighardt, Frank K. (Allentown, PA)

    1984-01-01T23:59:59.000Z

    A process is disclosed for the solvent refining of non-anthracitic coal at elevated temperatures and pressure in a hydrogen atmosphere using a hydrocarbon solvent which before being recycled in the solvent refining process is subjected to chemical treatment to extract substantially all nitrogenous and phenolic constituents from the solvent so as to improve the conversion of coal and the production of oil in the solvent refining process. The solvent refining process can be either thermal or catalytic. The extraction of nitrogenous compounds can be performed by acid contact such as hydrogen chloride or fluoride treatment, while phenolic extraction can be performed by caustic contact or contact with a mixture of silica and alumina.

  7. Table A2. Refiner/Reseller Prices of Aviation Fuels, Propane...

    U.S. Energy Information Administration (EIA) Indexed Site

    - W 73.5 See footnotes at end of table. A2. RefinerReseller Prices of Aviation Fuels, Propane, and Kerosene, by PAD District, 1983-Present Energy Information Administration ...

  8. Economic impact of the European Union Emission Trading Scheme : evidence from the refining sector

    E-Print Network [OSTI]

    Lacombe, Romain H

    2008-01-01T23:59:59.000Z

    I study the economic impact of the European Union Emission Trading Scheme (EU ETS) on the refining industry in Europe. I contrast previous ex-ante studies with the lessons from a series of interviews I conducted with ...

  9. Using a conformation-dependent stereochemical library improves crystallographic refinement of proteins

    SciTech Connect (OSTI)

    Tronrud, Dale E.; Berkholz, Donald S.; Karplus, P. Andrew (Oregon State U.)

    2010-07-02T23:59:59.000Z

    The major macromolecular crystallographic refinement packages restrain models to ideal geometry targets defined as single values that are independent of molecular conformation. However, ultrahigh-resolution X-ray models of proteins are not consistent with this concept of ideality and have been used to develop a library of ideal main-chain bond lengths and angles that are parameterized by the {phi}/{psi} angle of the residue [Berkholz et al. (2009), Structure, 17, 1316-1325]. Here, it is first shown that the new conformation-dependent library does not suffer from poor agreement with ultrahigh-resolution structures, whereas current libraries have this problem. Using the TNT refinement package, it is then shown that protein structure refinement using this conformation-dependent library results in models that have much better agreement with library values of bond angles with little change in the R values. These tests support the value of revising refinement software to account for this new paradigm.

  10. A Concept-Driven Construction of the Mondex Protocol using Three Refinements

    E-Print Network [OSTI]

    Banach, Richard

    as closely as possible to the original, or by adapting the problem to fit the style of the tool, thereby, the proof is monolithic, consisting of a single refinement. Other authors, particularly [19] and [20], have

  11. A ConceptDriven Construction of the Mondex Protocol using Three Refinements

    E-Print Network [OSTI]

    Banach, Richard

    as closely as possible to the original, or by adapting the problem to fit the style of the tool, thereby, the proof is monolithic, consisting of a single refinement. Other authors, particularly [19] and [20], have

  12. Table 46. Refiner No. 2 Distillate, Diesel Fuel, and Fuel Oil...

    Annual Energy Outlook 2013 [U.S. Energy Information Administration (EIA)]

    132.9 1,418.3 See footnotes at end of table. 46. Refiner No. 2 Distillate, Diesel Fuel, and Fuel Oil Volumes by PAD District and State Energy Information Administration ...

  13. Table 46. Refiner No. 2 Distillate, Diesel Fuel, and Fuel Oil...

    Gasoline and Diesel Fuel Update (EIA)

    839.2 135.0 1,251.9 See footnotes at end of table. 46. Refiner No. 2 Distillate, Diesel Fuel, and Fuel Oil Volumes by PAD District and State Energy Information Administration ...

  14. Table A3. Refiner/Reseller Prices of Distillate and Residual...

    Gasoline and Diesel Fuel Update (EIA)

    A3. RefinerReseller Prices of Distillate and Residual Fuel Oils, by PAD District, 1983-Present (Cents per Gallon Excluding Taxes) Geographic Area Year No. 1 Distillate No. 2...

  15. Optimized Execution of Action Chains through Subgoal Refinement Freek Stulp and Michael Beetz

    E-Print Network [OSTI]

    Cremers, Daniel

    Optimized Execution of Action Chains through Subgoal Refinement Freek Stulp and Michael Beetz, Germany {stulp,beetz}@in.tum.de Abstract In this paper we propose a novel computation model

  16. Refinement trajectory and determination of eigenstates by a wavelet based adaptive method

    SciTech Connect (OSTI)

    Pipek, Janos; Nagy, Szilvia [Department of Theoretical Physics, Institute of Physics, Budapest University of Technology and Economics, H-1521 Budapest (Hungary); Department of Telecommunication, Jedlik Anyos Institute of Informatics, Electrical and Mechanical Engineering, Szechenyi Istvan University, H-9026 Gyor, Egyetem ter 1 (Hungary)

    2006-11-07T23:59:59.000Z

    The detail structure of the wave function is analyzed at various refinement levels using the methods of wavelet analysis. The eigenvalue problem of a model system is solved in granular Hilbert spaces, and the trajectory of the eigenstates is traced in terms of the resolution. An adaptive method is developed for identifying the fine structure localization regions, where further refinement of the wave function is necessary.

  17. Refine your search Select options from the menu on the left hand

    E-Print Network [OSTI]

    Yener, Aylin

    ://psu.summon.serialssolutions.comhttp://psu.summon.serialssolutions.com F I N A L LY : RESEARCH AS EASYAS 1-2-3 #12;1 Enter search term into search box. 2 Refine results relevant articles were published in that year. Include or Exclude subject terms from your searchRefine your search Select options from the menu on the left hand side of the results screen

  18. inAir: Sharing Indoor Air Quality Measurements and Visualizations

    E-Print Network [OSTI]

    Mankoff, Jennifer

    evidence has indicated that indoor air pollution within homes and other buildings can be worse than the outdoor air pollution in even the largest and most industrialized cities. For example, the California Air Resources Board estimates that indoor air pollutant levels are 25-62% greater than outside levels [4

  19. Clearing the Air: "AIR" Training Session Wednesday, December 18

    E-Print Network [OSTI]

    Reed, Christopher A.

    Clearing the Air: "AIR" Training Session Wednesday, December 18 12 p.m. ­ 1:00 p.m. Human Resources/Tobacco- Free! Join us for an interactive session and learn more about "AIR" (Approach, Inform, Refer, and safe campus environment. Visit Clearing the Air website (http://tobaccofree.ucr.edu/) for more

  20. Air distribution effectiveness with stratified air distribution systems

    E-Print Network [OSTI]

    Chen, Qingyan "Yan"

    1 Air distribution effectiveness with stratified air distribution systems Kisup Lee* Zheng Jiang, Ph.D Qingyan Chen, Ph.D. Student Member ASHRAE Fellow ASHRAE ABSTRACT Stratified air distribution systems such as Traditional Displacement Ventilation (TDV) and Under- Floor Air Distribution (UFAD

  1. Croatian refiner meets waste water treatment standards, reduces fines

    SciTech Connect (OSTI)

    Meier, A.L. [Krofta Engineering Corp., Lenox, MA (United States); Nikolic, O. [INA Oil Refinery, Rijeka (Croatia)

    1995-11-27T23:59:59.000Z

    A new approach to waste water treatment at a refinery in Croatia produces effluent that not only meets the region`s regulations for disposal into the Adriatic Sea, but also surpasses the refinery`s specifications for recycling process water. Key to the dramatic reduction in pollutants was the installation of a Sandfloat unit developed by Krofta Engineering Corp. The Sandfloat unit is a dissolved air flotation clarifier that combines flocculation, flotation, and multilayer filtration to produce high-quality effluent. In fact, the effluent from the unit has a lower hydrocarbon concentration than water from the underground wells that supply process water to the refinery. While similar systems have been used for decades in industrial applications, this is the first time a Sandfloat unit has been installed in an oil refinery. The article describes the problem, refinery operations, treatment costs, and effluent recycling.

  2. Thickness-based adaptive mesh refinement methods for multi-phase flow simulations with thin regions

    SciTech Connect (OSTI)

    Chen, Xiaodong [The State Key Laboratory of Nonlinear Mechanics, Institute of Mechanics, Chinese Academy of Sciences, Beijing 100190 (China); Yang, Vigor, E-mail: vigor.yang@aerospace.gatech.edu [School of Aerospace Engineering, Georgia Institute of Technology, Atlanta, GA 30332-0150 (United States)

    2014-07-15T23:59:59.000Z

    In numerical simulations of multi-scale, multi-phase flows, grid refinement is required to resolve regions with small scales. A notable example is liquid-jet atomization and subsequent droplet dynamics. It is essential to characterize the detailed flow physics with variable length scales with high fidelity, in order to elucidate the underlying mechanisms. In this paper, two thickness-based mesh refinement schemes are developed based on distance- and topology-oriented criteria for thin regions with confining wall/plane of symmetry and in any situation, respectively. Both techniques are implemented in a general framework with a volume-of-fluid formulation and an adaptive-mesh-refinement capability. The distance-oriented technique compares against a critical value, the ratio of an interfacial cell size to the distance between the mass center of the cell and a reference plane. The topology-oriented technique is developed from digital topology theories to handle more general conditions. The requirement for interfacial mesh refinement can be detected swiftly, without the need of thickness information, equation solving, variable averaging or mesh repairing. The mesh refinement level increases smoothly on demand in thin regions. The schemes have been verified and validated against several benchmark cases to demonstrate their effectiveness and robustness. These include the dynamics of colliding droplets, droplet motions in a microchannel, and atomization of liquid impinging jets. Overall, the thickness-based refinement technique provides highly adaptive meshes for problems with thin regions in an efficient and fully automatic manner.

  3. PERFORMANCE EVALUATION OF AN AIR-TO-AIR HEAT PUMP COUPLED WITH TEMPERATE AIR-SOURCES INTEGRATED INTO A DWELLING

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    PERFORMANCE EVALUATION OF AN AIR-TO-AIR HEAT PUMP COUPLED WITH TEMPERATE AIR-SOURCES INTEGRATED.peuportier@mines-paristech.fr, Tel.: +33 1 40 51 91 51 ABSTRACT An inverter-driven air-to-air heat pump model has been developped capacity air-to-air heat pump coupled with temperate air sources (crawlspace, attic, sunspace, heat

  4. SYSTEMS ENGINEER 1 Northrop Grumman is seeking a recent college graduate, regardless of age, as a Systems Engineer 1 in

    E-Print Network [OSTI]

    Ghani, Nasir

    SYSTEMS ENGINEER 1 Northrop Grumman is seeking a recent college graduate, regardless of age, as a Systems Engineer 1 in our Albuquerque office. Responsibilities include performing use case analyses to support the definition and refinement of system requirements; development of system requirements

  5. Air PSE (Problem Solving Environment)

    E-Print Network [OSTI]

    Nizkorodov, Sergey

    PSE - 1 Air PSE (Problem Solving Environment) MODELLING OF AIR POLLUTION IN THE LOS ANGELES BASIN WITH AIR PSE Developed by Prof. Donald Dabdub Computational Environmental Sciences Laboratory Mechanical COMPUTER MODELS An air pollution model is a computer program that computes how the different chemical

  6. Compressed air energy storage system

    DOE Patents [OSTI]

    Ahrens, Frederick W. (Naperville, IL); Kartsounes, George T. (Naperville, IL)

    1981-01-01T23:59:59.000Z

    An internal combustion reciprocating engine is operable as a compressor during slack demand periods utilizing excess power from a power grid to charge air into an air storage reservoir and as an expander during peak demand periods to feed power into the power grid utilizing air obtained from the air storage reservoir together with combustible fuel. Preferably the internal combustion reciprocating engine is operated at high pressure and a low pressure turbine and compressor are also employed for air compression and power generation.

  7. Single-Duct Constant Air Volume System Supply Air Temperature Reset: Using Return Air Temperature or Outside Air Temperature? 

    E-Print Network [OSTI]

    Wei, G.; Turner, W. D.; Claridge, D.; Liu, M.

    2002-01-01T23:59:59.000Z

    space area. Room temperatures are controlled by pneumatic thermostats. The AHU has a minimum outside air damper and a maximum outside air damper. The minimum outside air damper is fully open when the AHU is in operation. The maximum outside air... of thermostat, and the relationship between room temperature set point and return air temperature. The Role Of Thermostat Traditional pneumatic thermostat is a proportional (P) type controller. It senses the space temperature changes and produces...

  8. Single-Duct Constant Air Volume System Supply Air Temperature Reset: Using Return Air Temperature or Outside Air Temperature?

    E-Print Network [OSTI]

    Wei, G.; Turner, W. D.; Claridge, D.; Liu, M.

    2002-01-01T23:59:59.000Z

    space area. Room temperatures are controlled by pneumatic thermostats. The AHU has a minimum outside air damper and a maximum outside air damper. The minimum outside air damper is fully open when the AHU is in operation. The maximum outside air... understand how this reset scheme responds to building load change, thus resulting in supply air temperature reset, it is helpful to explain the role of thermostat. In the following section, we explain the way how the thermostat works, the type...

  9. Command in air war : centralized vs. decentralized control of combat airpower

    E-Print Network [OSTI]

    Kometer, Michael W

    2005-01-01T23:59:59.000Z

    This study answers the question, "What has been the impact of the Information Age on the Air Force's doctrinal tenet of "centralized control and decentralized execution?" It traces the evolution of command and control of ...

  10. Auxiliary air injector assembly

    SciTech Connect (OSTI)

    Sager, R.L.

    1987-04-07T23:59:59.000Z

    This patent describes an auxiliary air injector assembly kit for replacement use to connect a secondary air line from an engine air pump to an exhaust pipe in a variety of combustion engine exhaust systems. The exhaust pipe has an auxiliary air receiving hole formed in a wall thereof. The assembly comprises a flexible conduit adapted to be readily cut to length and connected at one end to the secondary air line, a metal tube, means for connecting a first end of the metal tube to the other end of the flexible conduit, and a hollow fitting with an air flow-through passage and having a conical portion adapted to fit in the hole in a leak resistant manner. The fitting has a bearing portion with a convex spherical surface located outside the exhaust pipe when the conical portion is in the hole. A second end of the metal tube has a flange with a concave spherical surface to seat against the convex spherical surface in a leak resistant manner. A clamp means connects the metal tube to the exhaust pipe and applies pressure on the metal tube flange against the bearing portion of the fitting to hold the fitting in the hole. The clamp means includes a saddle having an opening larger than the tube but smaller than the tube flange. The tube extends through the saddle opening. The clamp means also includes a U-bolt assembly for extending around the exhaust pipe and forcing the saddle against the tube flange and toward the exhaust pipe.

  11. The third, use of quantum mechanics to evaluate the molecular energy and forces, holds promise for future refinements when applied wholesale,

    E-Print Network [OSTI]

    Sali, Andrej

    for future refinements when applied wholesale, but is already capable of producing valuable insight when

  12. COOEE bitumen: chemical aging

    E-Print Network [OSTI]

    Lemarchand, Claire A; Dyre, Jeppe C; Hansen, Jesper S

    2013-01-01T23:59:59.000Z

    We study chemical aging in "COOEE bitumen" using molecular dynamic simulations. The model bitumen is composed of four realistic molecule types: saturated hydrocarbon, resinous oil, resin, and asphaltene. The aging reaction is modelled by the chemical reaction: "2 resins $\\rightarrow$ 1 asphaltene". Molecular dynamic simulations of four bitumen compositions, obtained by a repeated application of the aging reaction, are performed. The stress autocorrelation function, the fluid structure, the rotational dynamics of the plane aromatic molecules, and the diffusivity of each molecule, are determined for the four different compositions. The aging reaction causes a significant dynamics slowdown, which is correlated to the aggregation of asphaltene molecules in larger and dynamically slower nanoaggregates. Finally, a detailed description of the role of each molecule types in the aggregation and aging processes is given.

  13. Hydrodynamic Modeling of Air Blast Propagation from the Humble Redwood Chemical High Explosive Detonations Using GEODYN

    SciTech Connect (OSTI)

    Chipman, V D

    2011-09-20T23:59:59.000Z

    Two-dimensional axisymmetric hydrodynamic models were developed using GEODYN to simulate the propagation of air blasts resulting from a series of high explosive detonations conducted at Kirtland Air Force Base in August and September of 2007. Dubbed Humble Redwood I (HR-1), these near-surface chemical high explosive detonations consisted of seven shots of varying height or depth of burst. Each shot was simulated numerically using GEODYN. An adaptive mesh refinement scheme based on air pressure gradients was employed such that the mesh refinement tracked the advancing shock front where sharp discontinuities existed in the state variables, but allowed the mesh to sufficiently relax behind the shock front for runtime efficiency. Comparisons of overpressure, sound speed, and positive phase impulse from the GEODYN simulations were made to the recorded data taken from each HR-1 shot. Where the detonations occurred above ground or were shallowly buried (no deeper than 1 m), the GEODYN model was able to simulate the sound speeds, peak overpressures, and positive phase impulses to within approximately 1%, 23%, and 6%, respectively, of the actual recorded data, supporting the use of numerical simulation of the air blast as a forensic tool in determining the yield of an otherwise unknown explosion.

  14. Air Resources: Prevention and Control of Air Contamination and Air Pollution, Air Quality Classifications and Standards, and Air Quality Area Classifications (New York)

    Broader source: Energy.gov [DOE]

    These regulations establish emissions limits and permitting and operational requirements for facilities that may contribute to air emissions. General air quality standards and standards for...

  15. Need for refining capacity creates opportunities for producers in Middle East

    SciTech Connect (OSTI)

    Ali, M.S.S. (Bahrain National Oil Co., Awali (Bahrain))

    1994-07-11T23:59:59.000Z

    Oil industry interest in refining has revived in the past few years in response to rising oil consumption. The trend creates opportunities, for countries in the Middle East, which do not own refining assets nearly in proportion to their crude oil reserved. By closing this gap between reserves and refining capacity, the countries can ease some of the instability now characteristic of the oil market. Some major oil producing countries have begun to move downstream. During the 1980s, Venezuela, Kuwait, Saudi Arabia, Libya, and other members of the Organization of Petroleum Exporting Countries acquired refining assets through direct total purchase or joint ventures. Nevertheless, the oil industry remains largely unintegrated, with the Middle East holding two thirds of worldwide oil reserves but only a small share downstream. As worldwide refining capacity swings from a period of surplus toward one in which the need for new capacity will be built. The paper discusses background of the situation, shrinking surplus, investment requirements, sources of capital, and shipping concerns.

  16. Empirical examination of allegations of ''below-cost'' retail selling of gasoline by refiners: Research study No. 038

    SciTech Connect (OSTI)

    Hogarty, T.F.; Lindstrom, P.M.

    1986-10-01T23:59:59.000Z

    It is alleged by some dealers that (major) refiners consistently sell their gasoline through directly operated stations at retail prices below the prices charged to resellers. The results of this examination, involving more than 2000 price comparisons, failed to reveal a single instance where the average monthly retail price at refiner operated stations was below the price charged resellers by refiners. This result obtained not only for all gasoline sales by major refiners, but also for specific grades of gasoline sold by all refiners. Moreover, a large majority of the average monthly price differentials were greater than 6 cents per gallon, and exceeded 10 cents per gallon in a significant number of instances. Thus, the data do not support the allegation of widespread ''below-cost'' selling by refiners through outlets which they own and operate. Therefore, the rationale offered for legislation mandating retail divorcement, or prohibiting ''below-cost'' is not supported by the evidence. 3 figs., 5 tabs.

  17. Vermont Air Pollution Control Regulations, Ambient Air Quality Standards (Vermont)

    Broader source: Energy.gov [DOE]

    The ambient air quality standards are based on the national ambient air quality standards. The Vermont standards are classified as primary and secondary standards and judged adequate to protect...

  18. Industrial HVAC Air-to-Air Energy Recovery Retrofit Economics

    E-Print Network [OSTI]

    Graham, E. L.

    1980-01-01T23:59:59.000Z

    Retrofitting air-to-air energy recovery equipment is relatively simply to design and easy to install. Additionally, HVAC energy recovery is almost risk free when compared to process retrofit. Life cycle cost analysis is the best way to illustrate...

  19. Compressed Air 101: Getting Compressed Air to Work

    E-Print Network [OSTI]

    Burke, J. J.; Bessey, E. G.

    "Air compressors are a significant industrial energy user. Based on a survey (conducted by Oregon State University and the Bonneville Power Administration) of energy audit reports from 125 plants, air compressors account for roughly 10% of total...

  20. Cold Air Distribution in Office Buildings: Technology Assessment for California

    E-Print Network [OSTI]

    Bauman, F.S.

    2008-01-01T23:59:59.000Z

    warmer room air with the cold supply air whenever the supplyroom air diffusion with cold supply air temperatures under

  1. The investigation of exhaust powered, automotive air cycle air conditioning 

    E-Print Network [OSTI]

    Holley, James Andrew

    1978-01-01T23:59:59.000Z

    TEE INVESTIGATION OF EXHAUST POWERED, AUTOMOTIVE AIR CYCLE AIR CONDITIONING A Thesis James Andrew Holley Submitted to the Graduate College of Texas ASM University in partial fulfillment of the requirement for the degree of MASTER OF SCIENCE... August 1978 Major SubJect: Mechanical Engineering THE INVESTIGATION OF EXHAUST POWERED, AUTOMOTIVE AIR CYCLE AIR CONDITIONING A Thesis hy James Andrew Holley Approved as to style and content by: Chairman of Committee) (Head of Departm nt) Memb e...

  2. Automating crystallographic structure solution and refinement of protein–ligand complexes

    SciTech Connect (OSTI)

    Echols, Nathaniel, E-mail: nechols@lbl.gov; Moriarty, Nigel W., E-mail: nechols@lbl.gov; Klei, Herbert E.; Afonine, Pavel V. [Lawrence Berkeley National Laboratory, Berkeley, CA 94720-8235 (United States); Bunkóczi, Gábor [University of Cambridge, Cambridge Institute for Medical Research, Wellcome Trust/MRC Building, Cambridge CB2 0XY (United Kingdom); Headd, Jeffrey J. [Lawrence Berkeley National Laboratory, Berkeley, CA 94720-8235 (United States); McCoy, Airlie J.; Oeffner, Robert D.; Read, Randy J. [University of Cambridge, Cambridge Institute for Medical Research, Wellcome Trust/MRC Building, Cambridge CB2 0XY (United Kingdom); Terwilliger, Thomas C. [Los Alamos National Laboratory, Los Alamos, NM 87545-0001 (United States); Adams, Paul D., E-mail: nechols@lbl.gov [Lawrence Berkeley National Laboratory, Berkeley, CA 94720-8235 (United States); University of California at Berkeley, Berkeley, CA 94720-1762 (United States)

    2014-01-01T23:59:59.000Z

    A software system for automated protein–ligand crystallography has been implemented in the Phenix suite. This significantly reduces the manual effort required in high-throughput crystallographic studies. High-throughput drug-discovery and mechanistic studies often require the determination of multiple related crystal structures that only differ in the bound ligands, point mutations in the protein sequence and minor conformational changes. If performed manually, solution and refinement requires extensive repetition of the same tasks for each structure. To accelerate this process and minimize manual effort, a pipeline encompassing all stages of ligand building and refinement, starting from integrated and scaled diffraction intensities, has been implemented in Phenix. The resulting system is able to successfully solve and refine large collections of structures in parallel without extensive user intervention prior to the final stages of model completion and validation.

  3. Environmental Pollution Air Pollution Dispersion Practical Air Pollution Dispersion

    E-Print Network [OSTI]

    Moncrieff, John B.

    Environmental Pollution Air Pollution Dispersion 1 of 5 Practical ­ Air Pollution Dispersion in the lectures how such models can be used to explain observed concentrations of air pollutants in an area and to test `what-if' scenarios for pollution control and reduction. You will use the Gaussian Plume Model

  4. Free kick instead of cross-validation in maximum-likelihood refinement of macromolecular crystal structures

    SciTech Connect (OSTI)

    Pražnikar, Jure [Institute Jožef Stefan, Jamova 39, 1000 Ljubljana (Slovenia); University of Primorska, (Slovenia); Turk, Dušan, E-mail: dusan.turk@ijs.si [Institute Jožef Stefan, Jamova 39, 1000 Ljubljana (Slovenia); Center of Excellence for Integrated Approaches in Chemistry and Biology of Proteins, (Slovenia)

    2014-12-01T23:59:59.000Z

    The maximum-likelihood free-kick target, which calculates model error estimates from the work set and a randomly displaced model, proved superior in the accuracy and consistency of refinement of crystal structures compared with the maximum-likelihood cross-validation target, which calculates error estimates from the test set and the unperturbed model. The refinement of a molecular model is a computational procedure by which the atomic model is fitted to the diffraction data. The commonly used target in the refinement of macromolecular structures is the maximum-likelihood (ML) function, which relies on the assessment of model errors. The current ML functions rely on cross-validation. They utilize phase-error estimates that are calculated from a small fraction of diffraction data, called the test set, that are not used to fit the model. An approach has been developed that uses the work set to calculate the phase-error estimates in the ML refinement from simulating the model errors via the random displacement of atomic coordinates. It is called ML free-kick refinement as it uses the ML formulation of the target function and is based on the idea of freeing the model from the model bias imposed by the chemical energy restraints used in refinement. This approach for the calculation of error estimates is superior to the cross-validation approach: it reduces the phase error and increases the accuracy of molecular models, is more robust, provides clearer maps and may use a smaller portion of data for the test set for the calculation of R{sub free} or may leave it out completely.

  5. Studies on design of a process for organo-refining of coal to obtain super clean coal

    SciTech Connect (OSTI)

    Sharma, C.S.; Sharma, D.K. [Indian Inst. of Tech., New Delhi (India). Centre for Energy Studies

    1999-08-01T23:59:59.000Z

    Organo-refining of coal results in refining the coal to obtain super clean coal and residual coal. Super clean coal may be used to obtain value added chemicals, products, and cleaner fuels from coal. In the present work, studies on the design of a semicontinuous process for organo-refining of one ton of coal have been made. The results are reported. This is only a cursory attempt for the design, and further studies may be required for designing this process for use in the development of a scaled-up process of organo-refining of coal.

  6. Iodine Loading of NO Aged Silver Exchanged Mordenite

    SciTech Connect (OSTI)

    Patton, K. K. [ORNL; Bruffey, S. H. [ORNL; Jubin, J. T. [ORNL; Walker, Jr., J. F. [ORNL

    2014-09-30T23:59:59.000Z

    In an off-gas treatment system for used nuclear fuel processing, a solid sorbent will typically be exposed to a gas stream for months at a time. This gas stream may be at elevated temperature and could contain water vapor, gaseous nitrogen oxides (NO{sub x}), nitric acid vapors, and a variety of other constituents. For this reason, it is important to evaluate the effects of long-term exposure, or aging, on proposed sorbents. Silver exchanged mordenite (AgZ) is being studied at Oak Ridge National Laboratory (ORNL) to determine its iodine sorption capacity after long term exposure to increasingly more complex chemical environments. Studies previously conducted at ORNL investigated the effects of aging reduced silver exchanged mordenite (Ag{sup 0}Z) in dry air, moist air, and NO2. This study investigated the effects of extended exposure to nitric oxide (NO) gas on the iodine capture performance of Ag{sup 0}Z. A deep bed of Ag{sup 0}Z was aged in a 1% nitric oxide (NO) air stream, and portions of the bed were removed at pre-determined intervals. After being removed from the NO stream, each sample was loaded with iodine in a thin bed configuration. These samples were analyzed by neutron activation analysis (NAA) to quantify the iodine content in the sample. Samples were removed at one week and one month. A 78% decrease in sample capacity was seen after one week of exposure, with no further decrease observed after 1 month of aging. The observed loss in capacity is larger in magnitude than previous studies exposing Ag{sup 0}Z to dry air, moist air, or NO2 gas. The aging study was terminated after one month and repeated; this successfully demonstrated the reproducibility of the results.

  7. Air Corrosivity in U.S. Outdoor-Air-Cooled Data Centers is Similar to That in Conventional Data Centers

    SciTech Connect (OSTI)

    Coles, Henry C.; Han, Taewon; Price, Phillip N.; Gadgil, Ashok J.; Tschudi, William F.

    2011-07-17T23:59:59.000Z

    There is a concern that environmental-contamination caused corrosion may negatively affect Information Technology (IT) equipment reliability. Nineteen data centers in the United States and two in India were evaluated using Corrosion Classification Coupons (CCC) to assess environmental air quality as it may relate IT equipment reliability. The data centers were of two basic types: closed and outside-air cooled. A closed data center provides cool air to the IT equipment using air conditioning in which only a small percent age of the recirculation air is make-up air continuously supplied from outside to meet human health requirements. An outside-air cooled data center uses outside air directly as the primary source for IT equipment cooling. Corrosion measuring coupons containing copper and silver metal strips were placed in both closed and outside-air cooled data centers. The coupons were placed at each data center (closed and outside-air cooled types) with the location categorized into three groups: (1) Outside - coupons sheltered, located near or at the supply air inlet, but located before any filtering, (2) Supply - starting just after initial air filtering continuing inside the plenums and ducts feeding the data center rooms, and (3) Inside located inside the data center rooms near the IT equipment. Each coupon was exposed for thirty days and then sent to a laboratory for a corrosion rate measurement analysis. The goal of this research was to investigate whether gaseous contamination is a concern for U.S. data center operators as it relates to the reliability of IT equipment. More specifically, should there be an increased concern if outside air for IT equipment cooling is used To begin to answer this question limited exploratory measurements of corrosion rates in operating data centers in various locations were undertaken. This study sought to answer the following questions: (1) What is the precision of the measurements (2) What are the approximate statistical distributions of copper and silver corrosion rates in the sampled data centers(3) To what extent are copper and silver corrosion measurements related (4) What is the relationship of corrosion rate measurements between outside-air cooled data centers compared to closed data centers (5) How do corrosivity measurements relate to IT equipment failure rates The data from our limited sample size suggests that most United States data center operators should not be concerned with environmental gaseous contamination causing high IT equipment failure rates even when using outside-air cooling. The research team recommends additional basic research on how environmental conditions, specifically gaseous contamination, affect electronic equipment reliability.

  8. Louisiana Air Control Law (Louisiana)

    Broader source: Energy.gov [DOE]

    This law states regulations for air quality control and states the powers and duties of the secretary of environmental quality. It provides information about permits and licenses, air quality...

  9. Tennessee Air Quality Act (Tennessee)

    Broader source: Energy.gov [DOE]

    The Tennessee Air Quality Act (AQA) delegates the power to maintain air quality in the State to the Department of Environment and Conservation. Under the Department of the Environment and...

  10. Air Pollution Control Fees (Ohio)

    Broader source: Energy.gov [DOE]

    Facilities with a potential to emit any one regulated air pollutant of a quantity greater than or equal to 100 tons per year, or any one hazardous air pollutant (HAP) greater than or equal to 10...

  11. Compressed Air Audits using AIRMaster

    E-Print Network [OSTI]

    Wheeler, G. M.; McGill, R. D.; Bessey, E. G.; Vischer, K.

    Air compressors are a significant industrial energy user and therefore a prime target for industrial energy audits. The project goal was to develop a software tool, AIRMaster, and supporting methodology for performing compressed air system audits...

  12. Fundamentals of Compressed Air Systems

    Office of Energy Efficiency and Renewable Energy (EERE)

    Find out how a compressed air system works and the benefits of optimal compressed air system performance. This initial class demonstrates how to compute the current cost of your plant's compressed...

  13. ,"Motor Gasoline Sales to End Users, Total Refiner Sales Volumes"

    U.S. Energy Information Administration (EIA) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page onYou are now leaving Energy.gov You are now leaving Energy.gov YouKizildere IRaghurajiConventional Gasoline Sales to End Users, Total Refiner Sales Volumes"forUsers, Total Refiner

  14. ,"U.S. Conventional Gasoline Refiner Sales Volumes"

    U.S. Energy Information Administration (EIA) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page onYou are now leaving Energy.gov You are now leaving Energy.gov YouKizildere IRaghurajiConventional Gasoline Sales to End Users, Total Refiner SalesConventional Gasoline Refiner Sales

  15. ,"U.S. Conventional, Average Refiner Gasoline Prices"

    U.S. Energy Information Administration (EIA) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page onYou are now leaving Energy.gov You are now leaving Energy.gov YouKizildere IRaghurajiConventional Gasoline Sales to End Users, Total Refiner SalesConventional Gasoline Refiner

  16. COMBUSTION-GENERATED INDOOR AIR POLLUTION

    E-Print Network [OSTI]

    Hollowell, C.D.

    2010-01-01T23:59:59.000Z

    The Status of Indoor Air Pollution Research 1976. Geometand appliances and air pollution levels in the indoorAnnual Meeting of the Air Pollution Control Association,

  17. COMBUSTION-GENERATED INDOOR AIR POLLUTION

    E-Print Network [OSTI]

    Hollowell, C.D.

    2011-01-01T23:59:59.000Z

    The Japanese Union of Air Pollution Prevention Associations,The Status of Indoor Air Pollution Research 1976, GeometAnnual Meeting of the Air Pollution Control Association,

  18. Review: Integrating Climate, Energy and Air Pollution

    E-Print Network [OSTI]

    Toohey, David E.

    2013-01-01T23:59:59.000Z

    Climate, Energy and Air Pollution By Gary Bryner with RobertEnergy, and Air Pollution. Cambridge, Massachusetts, The MITClimate, Energy, and Air Pollution provides a well-

  19. Radionuclide Air Emission Report for 2011

    E-Print Network [OSTI]

    Wahl, Linnea

    2012-01-01T23:59:59.000Z

    LBNL-470E-20Ì1 Radionuclide Air Emission Report for Preparedfor Estimating Fugitive Air Emissions of Radionuclides fromStandards for Hazardous Air Pollutants (Radionuclides),

  20. Oil and Gas Air Heaters 

    E-Print Network [OSTI]

    Kou, G.; Wang, H.; Zhou, J.

    2006-01-01T23:59:59.000Z

    , the relation of hot-air temperature, oil or gas consumption and fresh airflow is determined based on energy equilibrium....

  1. Oil and Gas Air Heaters

    E-Print Network [OSTI]

    Kou, G.; Wang, H.; Zhou, J.

    2006-01-01T23:59:59.000Z

    , the relation of hot-air temperature, oil or gas consumption and fresh airflow is determined based on energy equilibrium....

  2. TTProblem A Air Conditioning Machinery

    E-Print Network [OSTI]

    California at Berkeley, University of

    TTProblem A Air Conditioning Machinery Input file: ducts.in You are a technician for the Air Conditioning Machinery company (ACM). Unfortunately, when you arrive at a customer site to install some air conditioning ducts, you discover that you are running low on supplies. You have only six duct segments

  3. Air Pollution Socio-Economic

    E-Print Network [OSTI]

    Minnesota, University of

    Traffic Air Pollution and Socio-Economic Status Gregory C Pratt PhD Kristie Ellickson PhD #12 · Relationships #12;Living near traffic increases exposure to air pollution and is associated with adverse health exposed to traffic and air pollution. They are also more vulnerable and have an increased risk of adverse

  4. Microcomputer pollution model for civilian airports and Air Force bases. Model description

    SciTech Connect (OSTI)

    Segal, H.M.; Hamilton, P.L.

    1988-08-01T23:59:59.000Z

    This is one of three reports describing the Emissions and Dispersion Modeling System (EDMS). EDMS is a complex source emissions/dispersion model for use at civilian airports and Air Force bases. It operates in both a refined and a screening mode and is programmed for an IBM-XT (or compatible) computer. This report--MODEL DESCRIPTION--provides the technical description of the model. It first identifies the key design features of both the emissions (EMISSMOD) and dispersion (GIMM) portions of EDMS. It then describes the type of meteorological information the dispersion model can accept and identifies the manner in which it preprocesses National Climatic Center (NCC) data prior to a refined-model run. The report presents the results of running EDMS on a number of different microcomputers and compares EDMS results with those of comparable models. The appendices elaborate on the information noted above and list the source code.

  5. FLUIDIC: Metal Air Recharged

    ScienceCinema (OSTI)

    Friesen, Cody

    2014-04-02T23:59:59.000Z

    Fluidic, with the help of ARPA-E funding, has developed and deployed the world's first proven high cycle life metal air battery. Metal air technology, often used in smaller scale devices like hearing aids, has the lowest cost per electron of any rechargeable battery storage in existence. Deploying these batteries for grid reliability is competitive with pumped hydro installations while having the advantages of a small footprint. Fluidic's battery technology allows utilities and other end users to store intermittent energy generated from solar and wind, as well as maintain reliable electrical delivery during power outages. The batteries are manufactured in the US and currently deployed to customers in emerging markets for cell tower reliability. As they continue to add customers, they've gained experience and real world data that will soon be leveraged for US grid reliability.

  6. Air Observe System

    E-Print Network [OSTI]

    Alexander Bolonkin

    2007-01-10T23:59:59.000Z

    This manuscript contains a description and basic principles for observing inaccessible areas using low cost, easily deployed equipment. The basic premise is to suspend a tiny video camera at an altitude of 10 - 200 meters over the area to be surveyed. The TV camera supports at altitude by wind or balloon. The technical challenges regard the means by which the camera is suspended. Such a system may be used by military or police forces or by civil authorities for rescue missions or assessment of natural disasters. The method may be further developed for military applications by integrating the surveillance task with deployment of munitions. Key words: air observer, air suspended system, low altitude video observer.

  7. FLUIDIC: Metal Air Recharged

    SciTech Connect (OSTI)

    Friesen, Cody

    2014-03-07T23:59:59.000Z

    Fluidic, with the help of ARPA-E funding, has developed and deployed the world's first proven high cycle life metal air battery. Metal air technology, often used in smaller scale devices like hearing aids, has the lowest cost per electron of any rechargeable battery storage in existence. Deploying these batteries for grid reliability is competitive with pumped hydro installations while having the advantages of a small footprint. Fluidic's battery technology allows utilities and other end users to store intermittent energy generated from solar and wind, as well as maintain reliable electrical delivery during power outages. The batteries are manufactured in the US and currently deployed to customers in emerging markets for cell tower reliability. As they continue to add customers, they've gained experience and real world data that will soon be leveraged for US grid reliability.

  8. Air cathode structure manufacture

    DOE Patents [OSTI]

    Momyer, William R. (Palo Alto, CA); Littauer, Ernest L. (Los Altos Hills, CA)

    1985-01-01T23:59:59.000Z

    An improved air cathode structure for use in primary batteries and the like. The cathode structure includes a matrix active layer, a current collector grid on one face of the matrix active layer, and a porous, nonelectrically conductive separator on the opposite face of the matrix active layer, the collector grid and separator being permanently bonded to the matrix active layer. The separator has a preselected porosity providing low IR losses and high resistance to air flow through the matrix active layer to maintain high bubble pressure during operation of the battery. In the illustrated embodiment, the separator was formed of porous polypropylene. A thin hydrophobic film is provided, in the preferred embodiment, on the current collecting metal grid.

  9. Hybrid membrane--PSA system for separating oxygen from air

    DOE Patents [OSTI]

    Staiger, Chad L. (Albuquerque, NM); Vaughn, Mark R. (Albuquerque, NM); Miller, A. Keith (Albuquerque, NM); Cornelius, Christopher J. (Blackburg, VA)

    2011-01-25T23:59:59.000Z

    A portable, non-cryogenic, oxygen generation system capable of delivering oxygen gas at purities greater than 98% and flow rates of 15 L/min or more is described. The system consists of two major components. The first component is a high efficiency membrane capable of separating argon and a portion of the nitrogen content from air, yielding an oxygen-enriched permeate flow. This is then fed to the second component, a pressure swing adsorption (PSA) unit utilizing a commercially available, but specifically formulated zeolite compound to remove the remainder of the nitrogen from the flow. The system is a unique gas separation system that can operate at ambient temperatures, for producing high purity oxygen for various applications (medical, refining, chemical production, enhanced combustion, fuel cells, etc . . . ) and represents a significant advance compared to current technologies.

  10. Air Risk Information Support Center

    SciTech Connect (OSTI)

    Shoaf, C.R.; Guth, D.J. [Environmental Protection Agency, Washington, DC (United States)

    1990-12-31T23:59:59.000Z

    The Air Risk Information Support Center (Air RISC) was initiated in early 1988 by the US Environmental Protection Agency`s (EPA) Office of Health and Environmental Assessment (OHEA) and the Office of Air Quality Planning and Standards (OAQPS) as a technology transfer effort that would focus on providing information to state and local environmental agencies and to EPA Regional Offices in the areas of health, risk, and exposure assessment for toxic air pollutants. Technical information is fostered and disseminated by Air RISCs three primary activities: (1) a {open_quotes}hotline{close_quotes}, (2) quick turn-around technical assistance projects, and (3) general technical guidance projects. 1 ref., 2 figs.

  11. Federal/Industry Development of Energy-Conserving Technologies for the Chemical and Petroleum Refining Industries 

    E-Print Network [OSTI]

    Alston, T. G.; Humphrey, J. L.

    1981-01-01T23:59:59.000Z

    Argonne National Laboratory has started a program to identify future RD&D projects that (i) promise cost-effective savings of scarce fuels in the chemical and petroleum refining industries, (ii) are not likely to be pursued by industry alone...

  12. EIS-0069: Solvent Refined Coal-II Demonstration Project, Fort Martin, Monongalia County, West Virginia

    Broader source: Energy.gov [DOE]

    The U.S. Department of Energy developed this statement to assess the potential environmental, economic and social impacts associated with the construction and short-term operation of a 6,000-tons-per-stream-day-capacity facility that will demonstrate the technical operability, economic viability, and environmental acceptability of the solvent refined coal process at Fort Martin, West Virginia.

  13. Table 7. U.S. Refiner Motor Gasoline Volumes by Grade and Sales...

    Annual Energy Outlook 2013 [U.S. Energy Information Administration (EIA)]

    35.2 213.6 9.5 9.8 12.9 16.6 NA 29.5 See footnotes at end of table. 7. U.S. Refiner Motor Gasoline Volumes by Grade and Sales Type 14 Energy Information Administration ...

  14. Table A1. Refiner/Reseller Motor Gasoline Prices by Grade, PAD...

    Annual Energy Outlook 2013 [U.S. Energy Information Administration (EIA)]

    71.6 92.3 78.2 101.8 83.6 87.5 74.7 See footnotes at end of table. A1. RefinerReseller Motor Gasoline Prices by Grade, PAD District, and State, 1984-Present 452 Energy Information...

  15. Table 6. U.S. Refiner Motor Gasoline Prices by Grade and Sales...

    U.S. Energy Information Administration (EIA) Indexed Site

    62.2 68.5 90.1 89.6 82.4 70.9 NA 75.9 See footnotes at end of table. 6. U.S. Refiner Motor Gasoline Prices by Grade and Sales Type 12 Energy Information Administration ...

  16. Table 11. U.S. Refiner Oxygenated Motor Gasoline Volumes by...

    U.S. Energy Information Administration (EIA) Indexed Site

    - 4.9 0.4 0.4 0.3 0.4 - 0.7 See footnotes at end of table. 11. U.S. Refiner Oxygenated Motor Gasoline Volumes by Grade and Sales Type 22 Energy Information Administration ...

  17. Table 6. U.S. Refiner Motor Gasoline Prices by Grade and Sales...

    U.S. Energy Information Administration (EIA) Indexed Site

    61.5 67.3 89.8 89.5 82.2 69.4 71.1 74.9 See footnotes at end of table. 6. U.S. Refiner Motor Gasoline Prices by Grade and Sales Type 12 Energy Information Administration ...

  18. Table 7. U.S. Refiner Motor Gasoline Volumes by Grade and Sales...

    Annual Energy Outlook 2013 [U.S. Energy Information Administration (EIA)]

    33.9 215.8 9.7 10.0 12.1 16.3 0.0 28.4 See footnotes at end of table. 7. U.S. Refiner Motor Gasoline Volumes by Grade and Sales Type 14 Energy Information Administration ...

  19. Table 11. U.S. Refiner Oxygenated Motor Gasoline Volumes by...

    U.S. Energy Information Administration (EIA) Indexed Site

    W 5.6 0.5 0.5 0.5 0.4 - 0.9 See footnotes at end of table. 11. U.S. Refiner Oxygenated Motor Gasoline Volumes by Grade and Sales Type 22 Energy Information Administration ...

  20. The Nekrasov-Okounkov hook length formula: refinement, elementary proof, extension and applications

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    2008/05/09 The Nekrasov-Okounkov hook length formula: refinement, elementary proof, extension and applications Guo-Niu HAN ABSTRACT. -- The paper is devoted to the derivation of the expan- sion formula function for t-cores. Several applications are derived, including the "marked hook formula". 1

  1. Three Dimensional Adaptive Mesh Refinement on a Spherical Shell for Atmospheric Models with Lagrangian Coordinates

    E-Print Network [OSTI]

    Jablonowski, Christiane

    Three Dimensional Adaptive Mesh Refinement on a Spherical Shell for Atmospheric Models for Atmospheric Research 1. Introduction One of the most important advances needed in global climate models of this project is a parallel adaptive grid library, which is currently under development at the University

  2. Tools for macromolecular model building and refinement into electron cryo-microscopy reconstructions

    SciTech Connect (OSTI)

    Brown, Alan; Long, Fei; Nicholls, Robert A.; Toots, Jaan; Emsley, Paul; Murshudov, Garib, E-mail: garib@mrc-lmb.cam.ac.uk [MRC Laboratory of Molecular Biology, Francis Crick Avenue, Cambridge CB2 0QH (United Kingdom)

    2015-01-01T23:59:59.000Z

    A description is given of new tools to facilitate model building and refinement into electron cryo-microscopy reconstructions. The recent rapid development of single-particle electron cryo-microscopy (cryo-EM) now allows structures to be solved by this method at resolutions close to 3 Å. Here, a number of tools to facilitate the interpretation of EM reconstructions with stereochemically reasonable all-atom models are described. The BALBES database has been repurposed as a tool for identifying protein folds from density maps. Modifications to Coot, including new Jiggle Fit and morphing tools and improved handling of nucleic acids, enhance its functionality for interpreting EM maps. REFMAC has been modified for optimal fitting of atomic models into EM maps. As external structural information can enhance the reliability of the derived atomic models, stabilize refinement and reduce overfitting, ProSMART has been extended to generate interatomic distance restraints from nucleic acid reference structures, and a new tool, LIBG, has been developed to generate nucleic acid base-pair and parallel-plane restraints. Furthermore, restraint generation has been integrated with visualization and editing in Coot, and these restraints have been applied to both real-space refinement in Coot and reciprocal-space refinement in REFMAC.

  3. Grain refinement and texture development of cast bi90sb10 alloy via severe plastic deformation

    E-Print Network [OSTI]

    Im, Jae-taek

    2009-05-15T23:59:59.000Z

    The purpose of this work was to study learn about grain refinement mechanisms and texture development in cast n-type Bi90Sb10 alloy caused by severe plastic deformation. The practical objective is to produce a fine grained and textured...

  4. Proceedings of the conference on electron beam melting and refining - state of the art 1996

    SciTech Connect (OSTI)

    Bakish, R. [ed.

    1996-12-31T23:59:59.000Z

    This conference proceedings summarizes state-of-the-art work in the field of electron-beam melting and refining, as presented at the 1996 conference. Papers are grouped as follows: invited papers; tutorial papers; electron beam melting related fundamentals; electron beam evaporation papers; and miscellaneous papers. Separate abstracts have been submitted to the energy database for some contributions to this proceedings.

  5. REFINING AND MAINTAINING THE OPTIMAL PERFORMANCE OF THE CEBAF SRF SYSTEMS *

    E-Print Network [OSTI]

    REFINING AND MAINTAINING THE OPTIMAL PERFORMANCE OF THE CEBAF SRF SYSTEMS * C. Reece, J. Benesch CEBAF at Jefferson Lab is striving to achieve its maximum reliability at the maximum deliverable energy beam time when CEBAF is run near its maximum energy. Operation at increased rf power levels has

  6. Protein NMR Structures Refined with Rosetta Have Higher Accuracy Relative to Corresponding Xray Crystal Structures

    E-Print Network [OSTI]

    Baker, David

    refinement of protein NMR structures was also compared with restrained CS-Rosetta calculations. For proteins spectroscopy (NMR). While X-ray crystal structures are derived from electron density data and are often dynamics and has the advantage of not requiring crystallization. Solution NMR structure determination

  7. Iterative model-building, structure refinement, and density modification with the PHENIX AutoBuild Wizard

    SciTech Connect (OSTI)

    Los Alamos National Laboratory, Mailstop M888, Los Alamos, NM 87545, USA; Lawrence Berkeley National Laboratory, One Cyclotron Road, Building 64R0121, Berkeley, CA 94720, USA; Department of Haematology, University of Cambridge, Cambridge CB2 0XY, England; Terwilliger, Thomas; Terwilliger, T.C.; Grosse-Kunstleve, Ralf Wilhelm; Afonine, P.V.; Moriarty, N.W.; Zwart, P.H.; Hung, L.-W.; Read, R.J.; Adams, P.D.

    2007-04-29T23:59:59.000Z

    The PHENIX AutoBuild Wizard is a highly automated tool for iterative model-building, structure refinement and density modification using RESOLVE or TEXTAL model-building, RESOLVE statistical density modification, and phenix.refine structure refinement. Recent advances in the AutoBuild Wizard and phenix.refine include automated detection and application of NCS from models as they are built, extensive model completion algorithms, and automated solvent molecule picking. Model completion algorithms in the AutoBuild Wizard include loop-building, crossovers between chains in different models of a structure, and side-chain optimization. The AutoBuild Wizard has been applied to a set of 48 structures at resolutions ranging from 1.1 {angstrom} to 3.2 {angstrom}, resulting in a mean R-factor of 0.24 and a mean free R factor of 0.29. The R-factor of the final model is dependent on the quality of the starting electron density, and relatively independent of resolution.

  8. Iterative model building, structure refinement and density modification with the PHENIX AutoBuild wizard

    SciTech Connect (OSTI)

    Terwilliger, Thomas C., E-mail: terwilliger@lanl.gov [Los Alamos National Laboratory, Mailstop M888, Los Alamos, NM 87545 (United States); Grosse-Kunstleve, Ralf W.; Afonine, Pavel V.; Moriarty, Nigel W.; Zwart, Peter H. [Lawrence Berkeley National Laboratory, One Cyclotron Road, Building 64R0121, Berkeley, CA 94720 (United States); Hung, Li-Wei [Los Alamos National Laboratory, Mailstop M888, Los Alamos, NM 87545 (United States); Read, Randy J. [Department of Haematology, University of Cambridge, Cambridge CB2 0XY (United Kingdom); Adams, Paul D., E-mail: terwilliger@lanl.gov [Lawrence Berkeley National Laboratory, One Cyclotron Road, Building 64R0121, Berkeley, CA 94720 (United States); Los Alamos National Laboratory, Mailstop M888, Los Alamos, NM 87545 (United States)

    2008-01-01T23:59:59.000Z

    The highly automated PHENIX AutoBuild wizard is described. The procedure can be applied equally well to phases derived from isomorphous/anomalous and molecular-replacement methods. The PHENIX AutoBuild wizard is a highly automated tool for iterative model building, structure refinement and density modification using RESOLVE model building, RESOLVE statistical density modification and phenix.refine structure refinement. Recent advances in the AutoBuild wizard and phenix.refine include automated detection and application of NCS from models as they are built, extensive model-completion algorithms and automated solvent-molecule picking. Model-completion algorithms in the AutoBuild wizard include loop building, crossovers between chains in different models of a structure and side-chain optimization. The AutoBuild wizard has been applied to a set of 48 structures at resolutions ranging from 1.1 to 3.2 Å, resulting in a mean R factor of 0.24 and a mean free R factor of 0.29. The R factor of the final model is dependent on the quality of the starting electron density and is relatively independent of resolution.

  9. NWS Product Definition Document (PDD) for: Refinement of SPC Experimental Enhanced Resolution Thunderstorm Outlook

    E-Print Network [OSTI]

    NWS Product Definition Document (PDD) for: Refinement of SPC Experimental Enhanced Resolution replaces an existing PDD, whose evaluation period expired on 15 February 2008, and revises the current SPC will also evaluate changes in the distribution of SPC forecaster workload and the ability to maintain

  10. Most of the world's titanium output is refined into titanium dioxide (TiO2

    E-Print Network [OSTI]

    Torgersen, Christian

    Most of the world's titanium output is refined into titanium dioxide (TiO2 ), which is used to give.S. Geological Survey (USGS) supports science to understand · How and where titanium resources form and concentrate in the Earth's crust · How titanium resources interact with the environment to affect human

  11. Use of Lung Transplantation Survival Models to Refine Patient Selection in Cystic Fibrosis

    E-Print Network [OSTI]

    Adler, Fred

    Use of Lung Transplantation Survival Models to Refine Patient Selection in Cystic Fibrosis Theodore Angeles, California Lung transplantation in cystic fibrosis may improve survival for patients with low 5 and United Network for Organ Sharing data, we identified 845 lung transplant recipients from 1991

  12. Soundness and Separability of Workflow Nets in the Stepwise Refinement Approach

    E-Print Network [OSTI]

    Sidorova, Natalia

    Soundness and Separability of Workflow Nets in the Stepwise Refinement Approach Kees van Hee.sidorova@tue.nl, wsinmarc@win.tue.nl Abstract. Workflow nets are recognized as a modelling paradigm for the business process modelling. We introduce and investigate several cor- rectness notions for workflow nets, ranging from proper

  13. Soundness and Separability of Workflow Nets in the Stepwise Refinement Approach

    E-Print Network [OSTI]

    Sidorova, Natalia

    Soundness and Separability of Workflow Nets in the Stepwise Refinement Approach Kees van Hee.sidorova@tue.nl, wsinmarc@win.tue.nl Abstract. Workflow nets are recognized as a modelling paradigm for the business process modelling. We introduce and investigate several cor­ rectness notions for workflow nets, ranging from proper

  14. A Pareto-Optimal Refinement Method for Protein Design Lucas Gregorio Nivo n1.

    E-Print Network [OSTI]

    Baker, David

    Moretti1. , David Baker1,2 * 1 Department of Biochemistry, University of Washington, Seattle, Washington, United States of America, 2 Howard Hughes Medical Institute (HHMI), University of Washington, Seattle for functional site design. Citation: Nivo´n LG, Moretti R, Baker D (2013) A Pareto-Optimal Refinement Method

  15. Refinement of weed risk assessments for biofuels using Camelina sativa as a model species

    E-Print Network [OSTI]

    Peterson, Robert K. D.

    Refinement of weed risk assessments for biofuels using Camelina sativa as a model species Philip B and Environmental Sciences, Montana State University, PO Box 173120, Bozeman, MT 59717-3120, USA Summary 1. Biofuel. However, concerns have been raised on the invasiveness of biofuel feedstocks. Estimating invasion

  16. Nonrigid Motion Analysis Based on Dynamic Refinement of Finite Element Models

    E-Print Network [OSTI]

    Sarkar, Sudeep

    Nonrigid Motion Analysis Based on Dynamic Refinement of Finite Element Models Leonid V. Tsap finite element models. The method is based on the iterative analysis of the differences betweenÐPhysically-based vision, deformable models, nonrigid motion analysis, biomedical applications, finite element analysis. æ

  17. Environmental Regulations and Changes in Petroleum Refining Operations (Released in the STEO June 1998)

    Reports and Publications (EIA)

    1998-01-01T23:59:59.000Z

    Changes in domestic refining operations are identified and related to the summer Reid vapor pressure (RVP) restrictions and oxygenate blending requirements. This analysis uses published Energy Information Administration survey data and linear regression equations from the Short-Term Integrated Forecasting System (STIFS). The STIFS model is used for producing forecasts appearing in the Short-Term Energy Outlook.

  18. A Characteristic Domain Decomposition and SpaceTime Local Refinement Method for

    E-Print Network [OSTI]

    Sharpley, Robert

    partial differential equations model the reactive transport of solutes in groundwater and surface water with other domain decomposition and local refinement schemes. 1 Introduction First­order linear hyperbolic interfaces that introduce extra difficulties. Physical interfaces arise, for example, in the modeling

  19. A Characteristic Domain Decomposition and SpaceTime Local Refinement Method for

    E-Print Network [OSTI]

    South Carolina, University of

    model the reactive transport of solutes in groundwater and surface water, the movement of aerosols and local refinement schemes. 1 Introduction First­order linear hyperbolic partial differential equations that introduce extra difficulties. Physical interfaces arise, for example, in the modeling of transport processes

  20. A Characteristic Domain Decomposition and Space Time Local Refinement Method for

    E-Print Network [OSTI]

    Sharpley, Robert

    cause severe numerical difficulties [1­5]. Conventional finite difference or finite element methods­Lagrangian methods; linear hyperbolic problems; local refinement techniques I. INTRODUCTION First-order linear hyperbolic partial differential equations model the reactive transport of solutes in groundwater and surface

  1. A Refined Ethical Impact Assessment Tool and a Case Study of its Application

    E-Print Network [OSTI]

    California at San Diego, University of

    A Refined Ethical Impact Assessment Tool and a Case Study of its Application Michael Bailey1 , Erin? What impact does the immediacy of an event (e.g., DDoS) have on our response to the event? [4 understanding, and (iii) retrospectively apply this EIA to an ethically challenging, original study in ICTR. 1

  2. New Age Teaching: Beyond Didactics

    E-Print Network [OSTI]

    Vlaovic, Peter D; McDougall, Elspeth M

    2006-01-01T23:59:59.000Z

    Age Teaching: Beyond Didactics TheScientificWorldJOURNAL (New age teaching: beyond didactics. TSW Urology 1, 75–85.New Age Teaching: Beyond Didactics Peter D. Vlaovic and

  3. Electrocatalysts for Nonaqueous Lithium–Air Batteries:...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Electrocatalysts for Nonaqueous Lithium–Air Batteries: Status, Challenges, and Perspective. Electrocatalysts for Nonaqueous Lithium–Air Batteries: Status, Challenges,...

  4. Kinetics of Conversion of Air Bubbles to Air-Hydrate Crystals in Antarctic Ice

    E-Print Network [OSTI]

    P. B. Price

    1995-01-23T23:59:59.000Z

    The depth-dependence of bubble concentration at pressures above the transition to the air hydrate phase and the optical scattering length due to bubbles in deep ice at the South Pole are modeled using diffusion-growth data from the laboratory, taking into account the dependence of age and temperature on depth in the ice. The model fits the available data on bubbles in cores from Vostok and Byrd and on scattering length in deep ice at the South Pole. It explains why bubbles and air hydrate crystals co-exist in deep ice over a range of depths as great as 800 m and predicts that at depths below $\\rm \\sim$ 1400 m the AMANDA neutrino observatory at the South Pole will operate unimpaired by light scattering from bubbles.

  5. The Use of Re-Refined Oil in Vehicle Fleets Copyright 1996 Society of Automotive Engineers, Inc.

    E-Print Network [OSTI]

    Timothy T. Maxwell; Glen Hagler; Jesse C. Jones; Raghu Narayan; Atila Ertas

    A literature search to identify deleterious effects of using re-refined oil did not disclose any validated occurrences. Significant engine testing using re-refined lubricating oil is reported and no cases were discovered in which engine operation was affected negatively by the use of re-refined oil. The American Petroleum Institute (AFT) allows the use of re-refined base stock oils in the blending of end use lubricants. Based on oil sample testing performed in this research as well as other authoritative sources, it was determined that no significant chemical or physical differences exist between rerefined and virgin oils. Differences noted in this research were related to higher levels of polynuclear aromatics (PNA’s) in the re-refined oil. PNA’s

  6. Regenerative air heater

    DOE Patents [OSTI]

    Hasselquist, P.B.; Baldner, R.

    1980-11-26T23:59:59.000Z

    A gas-cooled steel skirt is used to support a refractory cored brick matrix and dome structure in a high temperature regenerative air heater useful in magnetohydrodynamic power generation. The steel skirt thermally expands to accommodate the thermal expansion of the dome structure despite substantial temperature differential thereby reducing relative movement between the dome bricks. Gas cooling of the steel skirt allows the structure to operate above its normal temperature during clean-out cycles and also allows for the control of the thermal expansion of the steel skirt.

  7. Hot air drum evaporator

    DOE Patents [OSTI]

    Black, Roger L. (Idaho Falls, ID)

    1981-01-01T23:59:59.000Z

    An evaporation system for aqueous radioactive waste uses standard 30 and 55 gallon drums. Waste solutions form cascading water sprays as they pass over a number of trays arranged in a vertical stack within a drum. Hot dry air is circulated radially of the drum through the water sprays thereby removing water vapor. The system is encased in concrete to prevent exposure to radioactivity. The use of standard 30 and 55 gallon drums permits an inexpensive compact modular design that is readily disposable, thus eliminating maintenance and radiation build-up problems encountered with conventional evaporation systems.

  8. Regenerative air heater

    DOE Patents [OSTI]

    Hasselquist, Paul B. (Maple Grove, MN); Baldner, Richard (Minnetonka, MN)

    1982-01-01T23:59:59.000Z

    A gas-cooled steel skirt is used to support a refractory cored brick matrix and dome structure in a high temperature regenerative air heater useful in magnetohydrodynamic power generation. The steel skirt thermally expands to accommodate the thermal expansion of the dome structure despite substantial temperature differential thereby reducing relative movement between the dome bricks. Gas cooling of the steel skirt allows the structure to operate above its normal temperature during clean-out cycles and also allows for the control of the thermal expansion of the steel skirt.

  9. Aging in community

    E-Print Network [OSTI]

    Fay, Justin (Justin Thomas)

    2008-01-01T23:59:59.000Z

    Baby Boomers are on the brink of retirement. According to U.S. Census Bureau projections, the number of people aged 65 and over will more than double in the coming decades, growing from 35 million in 2000 to 72 million in ...

  10. Abatement of Air Pollution: Prohibition of Air Pollution (Connecticut...

    Broader source: Energy.gov (indexed) [DOE]

    Environmental Regulations Provider Department of Energy and Environmental Protection All air pollution not otherwise covered by these regulations is prohibited. Stationary sources...

  11. Abatement of Air Pollution: Air Pollution Control Equipment and...

    Broader source: Energy.gov (indexed) [DOE]

    These regulations contain instructions for the operation and monitoring of air pollution control equipment, as well as comments on procedures in the event of equipment breakdown,...

  12. air surveillance air: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    of California eScholarship Repository Summary: chamber, passive sampling, passive solar house, measurementhouse, we planed the distribution of fresh air, passivepassive...

  13. Air Force program tests production of aviation turbine fuels from Utah and Kentucky bitumens

    SciTech Connect (OSTI)

    Not Available

    1986-09-01T23:59:59.000Z

    Ashland Petroleum Company and Sun Refining and Marketing participated in a US Air Force program to determine the costs, yields, physical characteristics, and chemical properties of aviation turbine fuels, Grades JP-4 and JP-8, produced from Kentucky and Utah bitumens. The processes used by both are summarized; Ashland used a different approach for each bitumen; Sun's processing was the same for both, but different from Ashland's. Chemical and physical properties are tabulated for the two raw bitumens. Properties of the eight fuels produced are compared with specification for similar type aviation turbine fuels.

  14. Oklahoma Clean Air Act (Oklahoma)

    Broader source: Energy.gov [DOE]

    This legislation establishes the authority for the Oklahoma Department of Environmental Quality to administer programs to maintain and monitor air quality across Oklahoma. The Department monitors...

  15. Nebraska Air Quality Regulations (Nebraska)

    Broader source: Energy.gov [DOE]

    These regulations, promulgated by the Department of Environmental Quality, contain provisions pertaining to ambient air quality standards, pollution source operating permits, emissions reporting,...

  16. An air line carries air at 800 kPa and 80C. An Air line ~ O O C insulated tank initially contains 20C air at a

    E-Print Network [OSTI]

    Huang, Haimei

    An air line carries air at 800 kPa and 80°C. An Air line ~ O O C insulated tank initially contains 20°C air at a pressure of 90kPa. The valve is opened, and air flows into the tank. Determine the final temperature of the air in the tank and the mass of air that enters the tank if the valve is left

  17. Reactive Air Aluminization

    SciTech Connect (OSTI)

    Choi, Jung-Pyung; Chou, Y. S.; Stevenson, Jeffry W.

    2011-10-28T23:59:59.000Z

    Ferritic stainless steels and other alloys are of great interest to SOFC developers for applications such as interconnects, cell frames, and balance of plant components. While these alloys offer significant advantages (e.g., low material and manufacturing cost, high thermal conductivity, and high temperature oxidation resistance), there are challenges which can hinder their utilization in SOFC systems; these challenges include Cr volatility and reactivity with glass seals. To overcome these challenges, protective coatings and surface treatments for the alloys are under development. In particular, aluminization of alloy surfaces offers the potential for mitigating both evaporation of Cr from the alloy surface and reaction of alloy constituents with glass seals. Commercial aluminization processes are available to SOFC developers, but they tend to be costly due to their use of exotic raw materials and/or processing conditions. As an alternative, PNNL has developed Reactive Air Aluminization (RAA), which offers a low-cost, simpler alternative to conventional aluminization methods.

  18. Air gun test evaluation

    SciTech Connect (OSTI)

    Carleton, J.J. II; Fox, L.; Rudy, C.R.

    1992-01-15T23:59:59.000Z

    A mechanical shock testing apparatus is used for testing the response of components subject to large accelerations in hostile environments. The test acceleration is provided by the impact of a bullet against a plate on which the component to be tested is mounted. This report describes a series of experiments that were performed to determine the dependence of the air gun test apparatus performance on incremental changes in the hardware configurations, changes in the pressure used to drive the bullet, and different accelerometers. The effect of variation of these experimental factors on the measured acceleration was determined using a Taguchi screening experimental design. Experimental settings were determined that can be used to operate the tester with a measured output within acceleration specifications.

  19. Inhalation intake of ambient air pollution in California's South Coast Air Basin

    E-Print Network [OSTI]

    Marshall, Julian D.; Granvold, Patrick W.; Hoats, Abigail S.; McKone, Thomas E.; Deakin, Elizabeth; Nazaroff, William W.

    2006-01-01T23:59:59.000Z

    survey data, and the air-pollution modeling group at Environfor vehicle-related air pollution exposure in minority andtotal health impact of air pollution. Urban planners often

  20. Hydrodynamical adaptive mesh refinement simulations of turbulent flows - I. Substructure in a wind

    E-Print Network [OSTI]

    Iapichino, L; Schmidt, W; Niemeyer, J C

    2008-01-01T23:59:59.000Z

    The problem of the resolution of turbulent flows in adaptive mesh refinement (AMR) simulations is investigated by means of 3D hydrodynamical simulations in an idealised setup, representing a moving subcluster during a merger event. AMR simulations performed with the usual refinement criteria based on local gradients of selected variables do not properly resolve the production of turbulence downstream of the cluster. Therefore we apply novel AMR criteria which are optimised to follow the evolution of a turbulent flow. We demonstrate that these criteria provide a better resolution of the flow past the subcluster, allowing us to follow the onset of the shear instability, the evolution of the turbulent wake and the subsequent back-reaction on the subcluster core morphology. We discuss some implications for the modelling of cluster cold fronts.

  1. Hydrodynamical adaptive mesh refinement simulations of turbulent flows - I. Substructure in a wind

    E-Print Network [OSTI]

    L. Iapichino; J. Adamek; W. Schmidt; J. C. Niemeyer

    2008-07-01T23:59:59.000Z

    The problem of the resolution of turbulent flows in adaptive mesh refinement (AMR) simulations is investigated by means of 3D hydrodynamical simulations in an idealised setup, representing a moving subcluster during a merger event. AMR simulations performed with the usual refinement criteria based on local gradients of selected variables do not properly resolve the production of turbulence downstream of the cluster. Therefore we apply novel AMR criteria which are optimised to follow the evolution of a turbulent flow. We demonstrate that these criteria provide a better resolution of the flow past the subcluster, allowing us to follow the onset of the shear instability, the evolution of the turbulent wake and the subsequent back-reaction on the subcluster core morphology. We discuss some implications for the modelling of cluster cold fronts.

  2. Iterative-build OMIT maps: map improvement by iterative model building and refinement without model bias

    SciTech Connect (OSTI)

    Terwilliger, Thomas C., E-mail: terwilliger@lanl.gov [Los Alamos National Laboratory, Los Alamos, NM 87545 (United States); Grosse-Kunstleve, Ralf W.; Afonine, Pavel V.; Moriarty, Nigel W.; Adams, Paul D. [Lawrence Berkeley National Laboratory, One Cyclotron Road, Building 64R0121, Berkeley, CA 94720 (United States); Read, Randy J. [Department of Haematology, University of Cambridge, Cambridge CB2 0XY (United Kingdom); Zwart, Peter H. [Lawrence Berkeley National Laboratory, One Cyclotron Road, Building 64R0121, Berkeley, CA 94720 (United States); Hung, Li-Wei [Los Alamos National Laboratory, Los Alamos, NM 87545 (United States)

    2008-05-01T23:59:59.000Z

    An OMIT procedure is presented that has the benefits of iterative model building density modification and refinement yet is essentially unbiased by the atomic model that is built. A procedure for carrying out iterative model building, density modification and refinement is presented in which the density in an OMIT region is essentially unbiased by an atomic model. Density from a set of overlapping OMIT regions can be combined to create a composite ‘iterative-build’ OMIT map that is everywhere unbiased by an atomic model but also everywhere benefiting from the model-based information present elsewhere in the unit cell. The procedure may have applications in the validation of specific features in atomic models as well as in overall model validation. The procedure is demonstrated with a molecular-replacement structure and with an experimentally phased structure and a variation on the method is demonstrated by removing model bias from a structure from the Protein Data Bank.

  3. Re-refining of Waste Oil Solvent Is Used in Treatment/Distillation Process

    E-Print Network [OSTI]

    unknown authors

    INDUSTRIAL APPLICATION. A combination solvent treatment/distillation process has been designed for re-refining industrial waste oil (such as equipment lubricants, metal-working oil, and process oil) and used automotive lubricants (engine oil, hydraulic oil, and gear oil) for reuse. WASTE ENERGY RECOVERY. Recycling of waste oil in the United States has the potential to save the energy equivalent of 7-12 million bbl of crude oil annually.1 WASTE OIL RECOVERY. Prior to 1960, a significant portion of the demand for automotive lubricating oil was met by re-relined used oil. At the time, 150 re-refineries produced 300 million gal of motor oil annually. Since 1960, however, the production of re-refined oil has steadily declined. In 1981, for example, out of about 1.2 billion gal of automobile lubricating oil and 1.6 billion gal of industrial lubricating oils purchased, 25 U.S. rerefineries

  4. Characterization of U-6Nb ingots produced via the electron beam cold hearth refining process

    SciTech Connect (OSTI)

    McKoon, R.H.

    1997-11-14T23:59:59.000Z

    A study was undertaken at Lawrence Livermore National Laboratory to characterize uranium, 6% niobium ingots produced via electron beam melting, hearth refining and continuous casting and to compare this material with conventional VIM/skull melt/VAR material. Samples of both the ingot and feed material were analyzed for niobium and trace metallic elements, carbon, oxygen and nitrogen. This material was also inspected metallographically and via microprobe analysis.

  5. Liquid-liquid extraction as the means of refining cottonseed oil

    E-Print Network [OSTI]

    Patel, Manubhai Chunibhai

    1956-01-01T23:59:59.000Z

    Cottonseed oil, as well as other vegetable oils, contain a number of non-triglyceride impurities, Jamieson and Baughman (1) report tne following in crude cottonseed oil: raffinose, pentosans& resins, protoses& peptcnes, phosphatides& eterols, phytosterols... in the crude oil& combines with or destroys phospho-lipids and other minor constituents and removes suspended foreign matter. These materials which have been rendered insoluble can be separated from the refined oil by settling or centrifugation...

  6. ,"U.S. Residual Fuel Oil Refiner Sales Volumes"

    U.S. Energy Information Administration (EIA) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National and Regional Data; Row: NAICS Codes; Column: Energy SourcesRefinery, Bulk Terminal, and Natural Gas Plant Stocks of SelectedRefiner

  7. Improved crystallographic models through iterated local density-guided model deformation and reciprocal-space refinement

    SciTech Connect (OSTI)

    Terwilliger, Thomas C., E-mail: terwilliger@lanl.gov [Los Alamos National Laboratory, Los Alamos, NM 87545 (United States); Read, Randy J. [University of Cambridge, Cambridge CB2 0XY (United Kingdom); Adams, Paul D. [Lawrence Berkeley National Laboratory, One Cyclotron Road, Building 64R0121, Berkeley, CA 94720 (United States); Brunger, Axel T. [Stanford University, 318 Campus Drive West, Stanford, CA 94305-5432 (United States); Afonine, Pavel V.; Grosse-Kunstleve, Ralf W. [Lawrence Berkeley National Laboratory, One Cyclotron Road, Building 64R0121, Berkeley, CA 94720 (United States); Hung, Li-Wei [Los Alamos National Laboratory, Los Alamos, NM 87545 (United States)

    2012-07-01T23:59:59.000Z

    A density-based procedure is described for improving a homology model that is locally accurate but differs globally. The model is deformed to match the map and refined, yielding an improved starting point for density modification and further model-building. An approach is presented for addressing the challenge of model rebuilding after molecular replacement in cases where the placed template is very different from the structure to be determined. The approach takes advantage of the observation that a template and target structure may have local structures that can be superimposed much more closely than can their complete structures. A density-guided procedure for deformation of a properly placed template is introduced. A shift in the coordinates of each residue in the structure is calculated based on optimizing the match of model density within a 6 Å radius of the center of that residue with a prime-and-switch electron-density map. The shifts are smoothed and applied to the atoms in each residue, leading to local deformation of the template that improves the match of map and model. The model is then refined to improve the geometry and the fit of model to the structure-factor data. A new map is then calculated and the process is repeated until convergence. The procedure can extend the routine applicability of automated molecular replacement, model building and refinement to search models with over 2 Å r.m.s.d. representing 65–100% of the structure.

  8. Constrained-Transport Magnetohydrodynamics with Adaptive-Mesh-Refinement in CHARM

    SciTech Connect (OSTI)

    Miniatii, Francesco; Martin, Daniel

    2011-05-24T23:59:59.000Z

    We present the implementation of a three-dimensional, second order accurate Godunov-type algorithm for magneto-hydrodynamic (MHD), in the adaptivemesh-refinement (AMR) cosmological code CHARM. The algorithm is based on the full 12-solve spatially unsplit Corner-Transport-Upwind (CTU) scheme. Thefluid quantities are cell-centered and are updated using the Piecewise-Parabolic- Method (PPM), while the magnetic field variables are face-centered and areevolved through application of the Stokes theorem on cell edges via a Constrained- Transport (CT) method. The so-called ?multidimensional MHD source terms?required in the predictor step for high-order accuracy are applied in a simplified form which reduces their complexity in three dimensions without loss of accuracyor robustness. The algorithm is implemented on an AMR framework which requires specific synchronization steps across refinement levels. These includeface-centered restriction and prolongation operations and a reflux-curl operation, which maintains a solenoidal magnetic field across refinement boundaries. Thecode is tested against a large suite of test problems, including convergence tests in smooth flows, shock-tube tests, classical two- and three-dimensional MHD tests,a three-dimensional shock-cloud interaction problem and the formation of a cluster of galaxies in a fully cosmological context. The magnetic field divergence isshown to remain negligible throughout. Subject headings: cosmology: theory - methods: numerical

  9. Rietveld Refinement

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level:Energy: Grid Integration Redefining What's PossibleRadiation Protection TechnicalResonantNovember 15 to March 15A Megawatt is

  10. Protective supplied breathing air garment

    DOE Patents [OSTI]

    Childers, E.L.; Hortenau, E.F. von.

    1984-07-10T23:59:59.000Z

    A breathing air garment is disclosed for isolating a wearer from hostile environments containing toxins or irritants includes a suit and a separate head protective enclosure or hood engaging a suit collar in sealing attachment. The hood and suit collar are cylindrically shaped and dimensioned to enable the wearer to withdraw his hands from the suit sleeves to perform manual tasks within the hood interior. Breathing air is supplied from an external air line with an air delivery hose attached to the hood interior. The hose feeds air into an annular halo-like fiber-filled plenum having spaced discharge orifices attached to the hood top wall. A plurality of air exhaust/check valves located at the suit extremities cooperate with the hood air delivery system to provide a cooling flow of circulating air from the hood throughout the suit interior. A suit entry seal provided on the suit rear torso panel permits access into the suit and is sealed with an adhesive sealing flap. 17 figs.

  11. Environmental Aspects of Air Transportation

    E-Print Network [OSTI]

    Innovation Center #12;2 Aviation and Climate #12;3 Combustion Products Commercial jet fuel is essentially FOR AIR TRANSPORTATIONCENTER FOR AIR TRANSPORTATION SYSTEMS RESEARCHSYSTEMS RESEARCH Metron Aviation GMU, and the process inside real engines is considerably more complex. Typical emission rates for jet aircraft (grams

  12. D0 Instrument Air System

    SciTech Connect (OSTI)

    Serges, T.J.; /Fermilab

    1988-09-15T23:59:59.000Z

    The main function of the instrument air system is to operate control valves associated with the cryogenics in the D0 hall. Occasionally, it will be used for purging purposes. Appendix A shows a schematic of the air instrument system along with a corresponding components list.

  13. EMISSIONS TO AIR OPERATIONAL PROCEDURE

    E-Print Network [OSTI]

    Harman, Neal.A.

    and refrigeration equipment. To minimise pollution risks by ensuring regular maintenance of equipment containing Act 1993. SCOPE: All air-conditioning and refrigeration equipment METHOD: Air-conditioning and refrigeration equipment: 1. Swansea University uses equipment containing ozone-depleting substances

  14. Title III hazardous air pollutants

    SciTech Connect (OSTI)

    Todd, R.

    1995-12-31T23:59:59.000Z

    The author presents an overview of the key provisions of Title III of the Clean Air Act Amendments of 1990. The key provisions include the following: 112(b) -- 189 Hazardous Air Pollutants (HAP); 112(a) -- Major Source: 10 TPY/25 TPY; 112(d) -- Application of MACT; 112(g) -- Modifications; 112(I) -- State Program; 112(j) -- The Hammer; and 112(r) -- Accidental Release Provisions.

  15. Air Force Enhanced Use Lease

    Broader source: Energy.gov (indexed) [DOE]

    S e r v i c e - E x c e l l e n c e Headquarters U.S. Air Force 1 Air Force Enhanced Use Lease Mr. Brian Brown 16 Oct. 12 I n t e g r i t y - S e r v i c e - E x c e l l e n c e 2...

  16. Air Force Renewable Energy Programs

    Broader source: Energy.gov (indexed) [DOE]

    in All We Do" I n t e g r i t y - S e r v i c e - E x c e l l e n c e THINK GREEN, BUILD GREEN, Topics Air Force Energy Use Air Force Facility Energy Center Current RE...

  17. Air Leakage and Air Transfer Between Garage and Living Space

    SciTech Connect (OSTI)

    Rudd, A.

    2014-09-01T23:59:59.000Z

    This research project focused on evaluation of air transfer between the garage and living space in a single-family detached home constructed by a production homebuilder in compliance with the 2009 International Residential Code and the 2009 International Energy Conservation Code. The project gathered important information about the performance of whole-building ventilation systems and garage ventilation systems as they relate to minimizing flow of contaminated air from garage to living space. A series of 25 multi-point fan pressurization tests and additional zone pressure diagnostic testing characterized the garage and house air leakage, the garage-to-house air leakage, and garage and house pressure relationships to each other and to outdoors using automated fan pressurization and pressure monitoring techniques. While the relative characteristics of this house may not represent the entire population of new construction configurations and air tightness levels (house and garage) throughout the country, the technical approach was conservative and should reasonably extend the usefulness of the results to a large spectrum of house configurations from this set of parametric tests in this one house. Based on the results of this testing, the two-step garage-to-house air leakage test protocol described above is recommended where whole-house exhaust ventilation is employed. For houses employing whole-house supply ventilation (positive pressure) or balanced ventilation (same pressure effect as the Baseline condition), adherence to the EPA Indoor airPLUS house-to-garage air sealing requirements should be sufficient to expect little to no garage-to-house air transfer.

  18. Analysis of a Dedicated Outdoor Air System and Low Temperature Supply Air Conditioning System

    E-Print Network [OSTI]

    Guang, L.; Li, R.

    2006-01-01T23:59:59.000Z

    This paper presents the principles and the characteristics of a dedicated outdoor air system (DOAS) and low temperature supply air system. DOAS is offered based on the demands of indoor air quality and the low temperature supply air system...

  19. Public Health Air Surveillance Evaluation Project Public Health Air Surveillance Evaluation (PHASE) Project

    E-Print Network [OSTI]

    Public Health Air Surveillance Evaluation Project Public Health Air Surveillance Evaluation (PHASE) Project Evaluating, Developing, and Delivering Air Quality Characterization Data to Environmental Public Public Health Tracking (EPHT) Network. The EPA is developing routinely available air quality information

  20. TAO, Vol. 16, No. 2, 331-343, June 2005 A Refined Historical Record of Volcanic Eruptions around Taiwan

    E-Print Network [OSTI]

    Lin, Andrew Tien-Shun

    . 2. RESULTS Five historical submarine eruptions around offshore Taiwan have been reported (Simkin in the Volcanoes of the World (Simkin and Siebert 1994). The refined results of five historical records around

  1. Cold air distribution in office buildings: technology assessment for califonia

    E-Print Network [OSTI]

    Bauman, Fred; Borgers, T.; LaBerge, P.; Gadgil, A.

    1993-01-01T23:59:59.000Z

    room air with the cold supply air whenever the supplyroomair diffusion with cold supply air temperatures space

  2. AIR LEAKAGE OF NEWLY INSTALLED RESIDENTIAL WINDOWS

    E-Print Network [OSTI]

    Weidt, John

    2013-01-01T23:59:59.000Z

    Tables 2.0.2a 2.0.2b PAGE Air Leakage Through Sash/FrameOperation Types . . . . . Air Leakage of Installed WindowsComparison of Window Types Air Leakage Performance of

  3. Air movement preferences observed in office buildings

    E-Print Network [OSTI]

    2007-01-01T23:59:59.000Z

    Movement – Good or Bad? Indoor Air 14: 40-45. Toftum, J (Quality Survey. Indoor Air 14 (8): 65–74. Internationalon the Perception of Indoor Air Quality during Immediate and

  4. WearAir: Expressive T-shirts for Air Quality Sensing Sunyoung Kim and Eric Paulos

    E-Print Network [OSTI]

    Mankoff, Jennifer

    are less proactively concerned with air quality. AIR POLLUTANT: VOLATILE ORGANIC COMPOUNDS Different types of air pollutants contribute to air quality in different locations: Ozone, CO, NOx and VOCs are major contributors to outdoor air pollution; and particulate matters, VOCs, carbon monoxide and lead are common air

  5. Air pollution kills. So what? Air quality engineering to improve public health

    E-Print Network [OSTI]

    Levinson, David M.

    9/14/12 1 Air pollution kills. So what? Air quality engineering to improve public health;9/14/12 2 Air Quality Engineering H Air Quality Engineering H #12;9/14/12 3 Really? Air pollution running out of coffins and florists were running out of flowers. -- BBC #12;9/14/12 4 Air pollution

  6. Air Leakage of Furnaces and Air Handlers Iain S. Walker, Mike Lubliner, Darryl Dickerhoff,

    E-Print Network [OSTI]

    Air Leakage of Furnaces and Air Handlers of California. #12;1 Air Leakage of Furnaces and Air Handlers Iain S. Walker, LBNL Mike Lubliner, Washington been made in reducing air leakage in residential and to a lesser extent small commercial forced air

  7. U.S. Air Force Fact Sheet Air Force Reserve Officer Training Corps

    E-Print Network [OSTI]

    Su, Xiao

    U.S. Air Force Fact Sheet Air Force Reserve Officer Training Corps Mission Develop Quality Leaders for the Air Force. Personnel and Resources Air Force Reserve Officer Training Corps (ROTC) includes four,796 new Second Lieutenants who entered active duty in the United States Air Force. Organization Air Force

  8. Air-Con International: Noncompliance Determination and Proposed...

    Energy Savers [EERE]

    Notice of Noncompliance Determination to Air-Con International finding that a variety of central air conditioners and air conditioning heat pumps distributed under the Air-Con...

  9. TESTING OF AIR-FLOW WINDOWS FOR EVALUATION AND APPLICATION

    E-Print Network [OSTI]

    Boehm, R.F.

    2014-01-01T23:59:59.000Z

    PRESSURE: TAPS RETURN** REFERENCE** Return-Air ConditioningMakeup-Air Conditioning Energy a.Through Glass Return-Air Conditioning Energy Makeuo-Air

  10. air bags compared: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    3. AIR TO AIR COMMUNICATION...3 4. SIMULATIONS Jain, Raj 435 Oil and Gas Air Heaters Texas A&M University - TxSpace Summary: Most conventional air...

  11. air entrainment: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    3. AIR TO AIR COMMUNICATION...3 4. SIMULATIONS Jain, Raj 174 Oil and Gas Air Heaters Texas A&M University - TxSpace Summary: Most conventional air...

  12. air brakes: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    3. AIR TO AIR COMMUNICATION...3 4. SIMULATIONS Jain, Raj 203 Oil and Gas Air Heaters Texas A&M University - TxSpace Summary: Most conventional air...

  13. al aire libre: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    3. AIR TO AIR COMMUNICATION...3 4. SIMULATIONS Jain, Raj 162 Oil and Gas Air Heaters Texas A&M University - TxSpace Summary: Most conventional air...

  14. INEEL AIR MODELING PROTOCOL ext

    SciTech Connect (OSTI)

    C. S. Staley; M. L. Abbott; P. D. Ritter

    2004-12-01T23:59:59.000Z

    Various laws stemming from the Clean Air Act of 1970 and the Clean Air Act amendments of 1990 require air emissions modeling. Modeling is used to ensure that air emissions from new projects and from modifications to existing facilities do not exceed certain standards. For radionuclides, any new airborne release must be modeled to show that downwind receptors do not receive exposures exceeding the dose limits and to determine the requirements for emissions monitoring. For criteria and toxic pollutants, emissions usually must first exceed threshold values before modeling of downwind concentrations is required. This document was prepared to provide guidance for performing environmental compliance-driven air modeling of emissions from Idaho National Engineering and Environmental Laboratory facilities. This document assumes that the user has experience in air modeling and dose and risk assessment. It is not intended to be a "cookbook," nor should all recommendations herein be construed as requirements. However, there are certain procedures that are required by law, and these are pointed out. It is also important to understand that air emissions modeling is a constantly evolving process. This document should, therefore, be reviewed periodically and revised as needed. The document is divided into two parts. Part A is the protocol for radiological assessments, and Part B is for nonradiological assessments. This document is an update of and supersedes document INEEL/INT-98-00236, Rev. 0, INEEL Air Modeling Protocol. This updated document incorporates changes in some of the rules, procedures, and air modeling codes that have occurred since the protocol was first published in 1998.

  15. Air Pollution Control Regulations: No. 22- Air Toxics (Rhode Island)

    Broader source: Energy.gov [DOE]

    Permits are required to construct, install, or modify any stationary source which has the potential to increase emissions of a listed toxic air contaminant by an amount greater than the minimum...

  16. Reference Inside KS1992 Tray Inside Air

    E-Print Network [OSTI]

    Llope, William J.

    Reference Inside KS1992 0.2 Tray Inside Air 0.5 Tray Inside Air 0.8 Tray Inside Air 0.2 Tray Side Wall Inner 0.2 Tray Side Wall Inner Under TAMP near sensor pos4 Under TAMP near sensor pos4 Air Gap Below TDIG pos1 Air Gap Below TDIG pos4 Air Gap Below TDIG pos6 HPTDC1 Chip pos6 HPTDC4 Chip pos6 HPTDC2

  17. Inertial impaction air sampling device

    DOE Patents [OSTI]

    Dewhurst, K.H.

    1987-12-10T23:59:59.000Z

    An inertial impactor to be used in an air sampling device for collection of respirable size particles in ambient air which may include a graphite furnace as the impaction substrate in a small-size, portable, direct analysis structure that gives immediate results and is totally self-contained allowing for remote and/or personal sampling. The graphite furnace collects suspended particles transported through the housing by means of the air flow system, and these particles may be analyzed for elements, quantitatively and qualitatively, by atomic absorption spectrophotometry. 3 figs.

  18. Inertial impaction air sampling device

    DOE Patents [OSTI]

    Dewhurst, K.H.

    1990-05-22T23:59:59.000Z

    An inertial impactor is designed which is to be used in an air sampling device for collection of respirable size particles in ambient air. The device may include a graphite furnace as the impaction substrate in a small-size, portable, direct analysis structure that gives immediate results and is totally self-contained allowing for remote and/or personal sampling. The graphite furnace collects suspended particles transported through the housing by means of the air flow system, and these particles may be analyzed for elements, quantitatively and qualitatively, by atomic absorption spectrophotometry. 3 figs.

  19. CSP Tower Air Brayton Combustor

    Broader source: Energy.gov [DOE]

    This fact sheet describes a concentrating solar power tower air Brayton combustor project awarded under the DOE's 2012 SunShot CSP R&D award program. The team, led by the Southwest Research Institute, is working to develop an external combustor that allows for the mixing of CSP-heated air with natural gas in hybridized power plants. This project aims to increase the temperature capabilities of the CSP tower air receiver and gas turbine to 1,000ºC and achieve energy conversion efficiencies greater than 50%.

  20. The investigation of exhaust powered, automotive air cycle air conditioning

    E-Print Network [OSTI]

    Holley, James Andrew

    1978-01-01T23:59:59.000Z

    domestic automobiles and trucks because of its proven success. This system requires approximately 4 hp (2. 983 kW)[3] for operation snd employs a pressurized fluorinated hydrocarbon (R-12), hereafter fluorocarbon, as a refrigerant. Most of the research... extraction and avoid the use of a fluorocarbon refrigerant. The maJority of work involved with the new units has associated itself in the area of utilizing an absorption cycle or air cycle. The absorption air conditioning unit differs significantly from...

  1. Colorado Air Pollution Control Division - Construction Permits...

    Open Energy Info (EERE)

    search OpenEI Reference LibraryAdd to library Web Site: Colorado Air Pollution Control Division - Construction Permits Forms and Air Pollutant Emission Notices (APENs)...

  2. Covered Product Category: Residential Central Air Conditioners...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Central Air Conditioners Covered Product Category: Residential Central Air Conditioners The Federal Energy Management Program (FEMP) provides acquisition guidance for residential...

  3. COMBUSTION-GENERATED INDOOR AIR POLLUTION

    E-Print Network [OSTI]

    Hollowell, C.D.

    2010-01-01T23:59:59.000Z

    The Status of Indoor Air Pollution Research 1976. GeometNovakov, T. : Formation of Pollution Particulate NitrogenGENERATED INDOOR AIR POLLUTION Dr. C. D. Hollowell, Dr. R.

  4. Stochastic Microenvironment Models for Air Pollution Exposure

    E-Print Network [OSTI]

    Naihua Duan

    2011-01-01T23:59:59.000Z

    human exposure to air pollution." SIMS Technical Report No.human exposure to air pollution." Environment International.Annual Meeting of the A i r Pollution Control Association,

  5. Cleaner Vehicles, Cleaner Fuel & Cleaner Air

    Broader source: Energy.gov (indexed) [DOE]

    EPA Office of Transportation and Air Quality Cleaner Vehicles, Cleaner Fuel, & Cleaner Air Overview of the 2007 Heavy-Duty Engine & Low Sulfur Diesel Fuel Program 2 Presentation...

  6. Lab Breakthrough: Desiccant Enhanced Evaporative Air Conditioning...

    Broader source: Energy.gov (indexed) [DOE]

    Desiccant Enhanced Evaporative Air Conditioning Lab Breakthrough: Desiccant Enhanced Evaporative Air Conditioning May 29, 2012 - 5:22pm Addthis This breakthrough combines desiccant...

  7. Missouri Air Conservation Law (Missouri)

    Broader source: Energy.gov [DOE]

    This law's purpose is to maintain the purity of the air resources of the state to protect the health, general welfare and physical property of the people, maximum employment and the full industrial...

  8. Kansas Air Quality Act (Kansas)

    Broader source: Energy.gov [DOE]

    No person shall construct, own, operate, install, alter or use any air contaminant emission stationary source which, in accordance with rules and regulations, the secretary finds may cause or...

  9. Kansas Air Quality Regulations (Kansas)

    Broader source: Energy.gov [DOE]

    All new air contaminant emission sources or alterations to emission sources that are required to be reported shall be in compliance with all applicable emission control regulations at the time that...

  10. Optimization of Air Conditioning Cycling

    E-Print Network [OSTI]

    Seshadri, Swarooph

    2012-10-19T23:59:59.000Z

    on a 3-ton residential air conditioner are then presented to intuitively understand the effect of expansion valve and evaporator fan cycling in a real system. A real time optimization method is explored and the feasibility, recommendations for a...

  11. Fuel Cell Systems Air Management

    E-Print Network [OSTI]

    Air Management Honeywell TIAX UTC Mechanology, LLC · Turbocompressor for PEM Fuel Cells · Hybrid-Machined Thin Film H2 Gas Sensors - ATMI · Sensor Development for PEM Fuel Cell Systems ­ Honeywell · Gallium

  12. Numerical relativity simulations of neutron star merger remnants using conservative mesh refinement

    E-Print Network [OSTI]

    Tim Dietrich; Sebastiano Bernuzzi; Maximiliano Ujevic; Bernd Bruegmann

    2015-04-06T23:59:59.000Z

    We study equal and unequal-mass neutron star mergers by means of new numerical relativity simulations in which the general relativistic hydrodynamics solver employs an algorithm that guarantees mass conservation across the refinement levels of the computational mesh. We consider eight binary configurations with total mass $M=2.7\\,M_\\odot$, mass-ratios $q=1$ and $q=1.16$, and four different equation of states (EOSs), and one configuration with a stiff EOS, $M=2.5M_\\odot$ and $q=1.5$. We focus on the post-merger dynamics and study the merger remnant, dynamical ejecta and the postmerger gravitational wave spectrum. Although most of the merger remnants form a hypermassive neutron star collapsing to a black hole+disk system on dynamical timescales, stiff EOSs can eventually produce a stable massive neutron star. Ejecta are mostly emitted around the orbital plane; favored by large mass ratios and softer EOS. The postmerger wave spectrum is mainly characterized by non-axisymmetric oscillations of the remnant. The stiff EOS configuration consisting of a $1.5M_\\odot$ and a $1.0M_\\odot$ neutron star shows a rather peculiar dynamics. During merger the companion star is very deformed; about~$\\sim0.03M_\\odot$ of rest-mass becomes unbound from the tidal tail due torque; and the merger remnant forms stable neutron star surrounded by a massive accretion disk $\\sim0.3M_\\odot$. Similar configurations might be particularly interesting for electromagnetic counterparts. Comparing results obtained with and without the conservative mesh refinement algorithm, we find that post-merger simulations can be affected by systematic errors if mass conservation is not enforced in the mesh refinement strategy. However, mass conservation also depends on grid details and on the artificial atmosphere setup. [abridged

  13. Ensemble refinement shows conformational flexibility in crystal structures of human complement factor D

    SciTech Connect (OSTI)

    Forneris, Federico; Burnley, B. Tom; Gros, Piet, E-mail: p.gros@uu.nl [Utrecht University, Padualaan 8, 3584 CH Utrecht (Netherlands)

    2014-03-01T23:59:59.000Z

    Ensemble-refinement analysis of native and mutant factor D (FD) crystal structures indicates a dynamical transition in FD from a self-inhibited inactive conformation to a substrate-bound active conformation that is reminiscent of the allostery in thrombin. Comparison with previously observed dynamics in thrombin using NMR data supports the crystallographic ensembles. Human factor D (FD) is a self-inhibited thrombin-like serine proteinase that is critical for amplification of the complement immune response. FD is activated by its substrate through interactions outside the active site. The substrate-binding, or ‘exosite’, region displays a well defined and rigid conformation in FD. In contrast, remarkable flexibility is observed in thrombin and related proteinases, in which Na{sup +} and ligand binding is implied in allosteric regulation of enzymatic activity through protein dynamics. Here, ensemble refinement (ER) of FD and thrombin crystal structures is used to evaluate structure and dynamics simultaneously. A comparison with previously published NMR data for thrombin supports the ER analysis. The R202A FD variant has enhanced activity towards artificial peptides and simultaneously displays active and inactive conformations of the active site. ER revealed pronounced disorder in the exosite loops for this FD variant, reminiscent of thrombin in the absence of the stabilizing Na{sup +} ion. These data indicate that FD exhibits conformational dynamics like thrombin, but unlike in thrombin a mechanism has evolved in FD that locks the unbound native state into an ordered inactive conformation via the self-inhibitory loop. Thus, ensemble refinement of X-ray crystal structures may represent an approach alternative to spectroscopy to explore protein dynamics in atomic detail.

  14. Direct Reduction of Waste through Refining of DOE Metal Assets - 13632

    SciTech Connect (OSTI)

    Hargett, Michael C.; Terekhov, Dimitri; Khozan, Kamran M. [Chemical Vapour Metal Refining - CVMR (United States)] [Chemical Vapour Metal Refining - CVMR (United States)

    2013-07-01T23:59:59.000Z

    CVMR{sup R} presents a technology for refining nickel from the enrichment barrier materials of the DOE that is proven through 100 years of use by the metals industry. CVMR{sup R} applies modern controls, instrumentation for process and monitoring of the system, and innovative production methods to produce a wide spectrum of products that generate new technology applications and improvements to our society and economy. CVMR{sup R} will receive barrier materials as a secure operation and size reduce the metal to a shred that is fed to a carbonylation reactor where nickel is reacted with carbon monoxide and generate nickel carbonyl. The carbonyl will be filtered and decomposed with heat to form a variety of products that include high value nano powders, coated substrates, net shapes and pure nickel. The residue from the reactor will retain radionuclides from enrichment activities. The carbon monoxide will only react and extract nickel under the operating conditions to leave volumetric contamination in the unreacted residue. A demonstration plant was designed and built by CVMR{sup R} and operated by BWXT, to demonstrate the systems capabilities to DOE in 2006. A pilot plant operation precedes the detailed design of the nickel refinery and provides essential data for design, safe work practices, waste characterizations and system kinetics and confirms the project feasibility. CVMR{sup R} produces nickel products that are cleaner than the nickel in U.S. commerce and used by industry today. The CVMR{sup R} process and systems for nickel refining is well suited for DOE materials and will provide value through environmental stewardship, recovery of high value assets, and support of the DOE environmental remediation programs as the refined nickel generates additional long term benefits to local communities. (authors)

  15. Optimising the Fresh Air Economiser

    E-Print Network [OSTI]

    Biship, R.

    2013-01-01T23:59:59.000Z

    , S., ?Economizers in Air Handling Systems?, CED Engineering Course M01-014, Stony Point New York, 2000. Moser, D., ?Free Cooling: Don?t Let Savings Slip Away?, Portland Energy Conservation Inc., published in Building Operating Management.... New Zealand, Standard NZS 4303:1990, Ventilation for Acceptable Indoor Air Quality, Standards Association of New Zealand, Wellington. Portland Energy Conservation Inc., from Functional Testing Guide on website: (http...

  16. Progress toward uranium scrap recycling via electron beam cold hearth refining

    SciTech Connect (OSTI)

    McKoon, R.H.

    1994-12-15T23:59:59.000Z

    A 250 kW electron beam cold hearth refining (EBCHR) melt furnace at Lawrence Livermore National Laboratory (LLNL) has been in operation for over a year producing 5.5 in.-diameter ingots of various uranium alloys. Production of in-specification uranium-6%-niobium (U-6Nb) alloy ingots has been demonstrated using Virgin feedstock. A vibratory scrap feeder has been installed on the system and the ability to recycle chopped U-6Nb scrap has been established. A preliminary comparison of vacuum arc remelted (VAR) and electron beam (EB) melted product is presented.

  17. Progress toward uranium scrap recycling via Electron Cold Hearth Refining (EBCHR)

    SciTech Connect (OSTI)

    McKoon, R.H.

    1994-12-22T23:59:59.000Z

    A 250 kW electron beam cold hearth refining (EBCHR) melt furnace at Lawrence Livermore National Laboratory (LLNL) has been in operation for over a year producing 5.5 in.-diameter ingots of various uranium alloys. Production of in-specification uranium-6% - niobium (U-6Nb) alloy ingots has been demonstrated using virgin feedstock. A vibratory scrap feeder has been installed on the system and the ability to recycle chopped U-6Nb scrap has been established. A preliminary comparison of vacuum arc remelted (VAR) and electron beam (EB) melted product is presented.

  18. Progress toward uranium scrap recycling via electron beam cold hearth refining

    SciTech Connect (OSTI)

    McKoon, R.H. [Lawrence Livermore National Lab., CA (United States)

    1994-12-31T23:59:59.000Z

    A 250 kW electron beam cold hearth refining (EBCHR) melt furnace at Lawrence Livermore National Laboratory (LLNL) has been in operation for over a year producing 5.5 in.-diameter ingots of various uranium alloys. Production of in-specification uranium 6% niobium (U-6Nb) alloy ingots has been demonstrated using virgin feedstock. A vibratory scrap feeder has been installed on the system and the ability to recycle chopped U-6Nb scrap has been established. A preliminary comparison of vacuum arc remelted (VAR) and electron beam (EB) melted product is presented.

  19. A study of acid sludge obtained in the refining of petroleum

    E-Print Network [OSTI]

    Johnson, Albert Sidney

    1923-01-01T23:59:59.000Z

    fo. petroleum Refin- eries {S l yellow colo of petroleum after ref in&ng m:y be due to impurities in the sulphurio &icid used ~ Since it is known that nitro. ?en trioxide, nitro en pentoxide, and selenium dioxide will cayuse discolor ~tion... of the sludge with ocustio soda o soda ash, &nd the "mixing" of the neutrul- ised sludge eith fuel oil. Much i&ttentlon h s been:i eu t:& the recover" of tho sludge acid, i. nd but little cr no uttention to thc study of the orgunic c&ntent of the caid sludge...

  20. HASSP and HEAVY: Tools for automated heavy atom searches and refinement

    SciTech Connect (OSTI)

    Terwilliger, T.T.

    1994-06-01T23:59:59.000Z

    In this tutorial, a simple example using model data for one derivative with anomalous information will be used to demonstrate the use of HASSP and HEAVY in heavy atom determination and refinement. The data used here will actually be based on model MAD data that has been converted to MIR format using MADMRG, but the treatment is identical to that for any other SIR+anomalous data. The data nd most of the programs discussed here can be obtained by e-mail from ``terwil @prov2.lanl.gov`` along with VAX-specific command files to run the data through.

  1. Studies of the refining of crude cottonseed oil and its solutions in commercial hexane

    E-Print Network [OSTI]

    Zeitoun, Mohamed Ali

    1958-01-01T23:59:59.000Z

    oil. In a more recent patent (17) Clayton used 1.5 per cent by weight of 29 per cent ammonium hydroxide to refine soybean oil. The well-mixed oil and ammonia solution is heated to 200?F., then rapidly cooled to 150?F., and then centrifuged... neutralized by soda ash. The soap- stock is removed in a multi-tray thickener. The neutralized miscella is then washed countercurrently with dilute caustic soda solution then with water. It is claimed that this method substantially reduces oil loss...

  2. ,"U.S. Motor Gasoline Refiner Sales Volumes"

    U.S. Energy Information Administration (EIA) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National and Regional Data; Row: NAICS Codes; Column: Energy Sources andPlant Liquids,+ LeasePriceExpectedOther CountriesTrinidadRefiner Sales

  3. Table 3b. Imported Refiner Acquisition Cost of Crude Oil, Projected vs. Actual

    U.S. Energy Information Administration (EIA) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page onYou are now leaving Energy.gov You are now leaving Energy.gov YouKizildere IRaghuraji Agro IndustriesTownDells,1Stocks Nov-14Total Delivered Residentialtightb. Imported Refiner

  4. Petroleum Refining Sector (NAICS 324110) Energy and GHG Combustion Emissions Profile, November 2012

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels DataDepartment of Energy Your Density Isn'tOrigin of Contamination in235-1 TermoelectricaPavingPerry Luksin About69 2.4 PETROLEUM REFINING

  5. NREL Refines Method to Convert Lignin to Nylon Precursor - News Releases |

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Saleshttp://www.fnal.gov/directorate/nalcal/nalcal02_07_05_files/nalcal.gifNREL NREL Refines Method to Convert Lignin to Nylon

  6. ,"Conventional Gasoline Sales to End Users, Total Refiner Sales Volumes"

    U.S. Energy Information Administration (EIA) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page onYou are now leaving Energy.gov You are now leaving Energy.gov YouKizildere IRaghurajiConventional Gasoline Sales to End Users, Total Refiner Sales Volumes" ,"Click worksheet

  7. ,"Kerosene-Type Jet Fuel Sales to End Users Refiner Sales Volumes"

    U.S. Energy Information Administration (EIA) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page onYou are now leaving Energy.gov You are now leaving Energy.gov YouKizildere IRaghurajiConventional Gasoline Sales to End Users, Total Refiner Sales Volumes"for

  8. ,"No. 2 Diesel Fuel Sales to End Users Refiner Sales Volumes"

    U.S. Energy Information Administration (EIA) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page onYou are now leaving Energy.gov You are now leaving Energy.gov YouKizildere IRaghurajiConventional Gasoline Sales to End Users, Total Refiner Sales Volumes"forUsers,

  9. ,"No. 2 Distillate Sales to End Users Refiner Sales Volumes"

    U.S. Energy Information Administration (EIA) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page onYou are now leaving Energy.gov You are now leaving Energy.gov YouKizildere IRaghurajiConventional Gasoline Sales to End Users, Total Refiner Sales Volumes"forUsers,Sales to End

  10. ,"Residual Fuel Oil Sales to End Users Refiner Sales Volumes"

    U.S. Energy Information Administration (EIA) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page onYou are now leaving Energy.gov You are now leaving Energy.gov YouKizildere IRaghurajiConventional Gasoline Sales to End Users, Total Refiner Sales Volumes"forUsers,Sales to Endto

  11. ,"U.S. Reformulated, Average Refiner Gasoline Prices"

    U.S. Energy Information Administration (EIA) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page onYou are now leaving Energy.gov You are now leaving Energy.gov YouKizildere IRaghurajiConventional Gasoline Sales toReformulated, Average Refiner Gasoline Prices" ,"Click

  12. ,"U.S. Sales for Resale, Total Refiner Motor Gasoline Sales Volumes"

    U.S. Energy Information Administration (EIA) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page onYou are now leaving Energy.gov You are now leaving Energy.gov YouKizildere IRaghurajiConventional Gasoline Sales toReformulated, Average Refiner Gasoline Prices"Sales Volumes

  13. ,"U.S. Sales to End Users, Total Refiner Motor Gasoline Sales Volumes"

    U.S. Energy Information Administration (EIA) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page onYou are now leaving Energy.gov You are now leaving Energy.gov YouKizildere IRaghurajiConventional Gasoline Sales toReformulated, Average Refiner Gasoline Prices"SalesSales

  14. Trials and tribulations implementing the Clean Air Act Title V in fourteen air districts

    SciTech Connect (OSTI)

    Moore, C. [Environmental Affairs Santa Fe Pacific Pipeline Partners, Orange, CA (United States)

    1998-12-31T23:59:59.000Z

    Santa Fe pacific Pipeline Partners, L.P. (SFPP) is a refined petroleum pipeline operating in six states in the western United States. Sixteen terminals are subject to the Title V permit to operate requirements. There are many obstacles to overcome, not only when preparing applications for Title V operating permits, but in the implementation phase of the project as well. Each Air District has its own set of rules and regulations that must be adhered to in preparing the application. For example, some districts required the insignificant sources to be documented and included in compliance plans and some do not. The format required for the application varies from stringent forms that must be completed to no forms at all. In preparing the Title V application for SFPP, the author quickly realized if this confusion was transferred to the implementation phase, compliance would be a failure. Therefore, early on the environmental manager instituted a training program. Beginning with a pilot program in one district the author began training managers and supervisors. This program quickly was expanded to include senior vice presidents and technicians. This training session was a one hour of general overview to visually describe how the Title V process would affect the facilities. As a result of this training, virtually every employee became familiar with how the Title V program was affecting the facilities. Engineering and Customer Service is instructed to notify the manager of any and every new project so it could undergo a review to determine if it affected a Title V facility. The field acts as a check of the system. Any change or modification at any facility is immediately under scrutiny for Title V implications. Another obstacle to overcome is to help the facility deal with something that is new and basically a different way of operating.

  15. Microstructural Features in Aged Erbium Tritide Foils

    SciTech Connect (OSTI)

    Gelles, David S.; Brewer, L. N.; Kotula, Paul G.; Cowgill, Donald F.; Busick, C. C.; Snow, C. S.

    2008-01-01T23:59:59.000Z

    Aged erbium tritide foil specimens are found to contain five distinctly different microstructural features. The general structure was of large columnar grains of ErT2. But on a fine scale, precipitates believed to be erbium oxy-tritides and helium bubbles could be identified. The precipitate size was in the range of ~10 nm and the bubbles were of an unusual planar shape on {111} planes with an invariant thickness of ~1 nm and a diameter on the order of 10 nm. Also, an outer layer containing no fine precipitate structure and only a few helium bubbles was present on foils. This layer is best described as a denuded zone which probably grew during aging in air. Finally, large embedded Er2O3 particles were found at low density and non-uniformly distributed, but sometimes extending through the thickness of the foil. A failure mechanism allowing the helium to escape is suggested by observed cracking between bubbles closer to end of life.

  16. Conformation-dependent backbone geometry restraints set a new standard for protein crystallographic refinement

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Moriarty, Nigel W.; Tronrud, Dale E.; Adams, Paul D.; Karplus, P. Andrew

    2014-09-01T23:59:59.000Z

    Ideal values of bond angles and lengths used as external restraints are crucial for the successful refinement of protein crystal structures at all but the highest of resolutions. The restraints in common usage today have been designed based on the assumption that each type of bond or angle has a single ideal value independent of context. However, recent work has shown that the ideal values are, in fact, sensitive to local conformation, and as a first step toward using such information to build more accurate models, ultra-high resolution protein crystal structures have been used to derive a conformation-dependent library (CDL)more »of restraints for the protein backbone (Berkholz et al. 2009. Structure. 17, 1316). Here, we report the introduction of this CDL into the Phenix package and the results of test refinements of thousands of structures across a wide range of resolutions. These tests show that use of the conformation dependent library yields models that have substantially better agreement with ideal main-chain bond angles and lengths and, on average, a slightly enhanced fit to the X-ray data. No disadvantages of using the backbone CDL are apparent. In Phenix usage of the CDL can be selected by simply specifying the cdl=True option. This successful implementation paves the way for further aspects of the context-dependence of ideal geometry to be characterized and applied to improve experimental and predictive modelling accuracy.« less

  17. Hydrodynamical adaptive mesh refinement simulations of turbulent flows - II. Cosmological simulations of galaxy clusters

    E-Print Network [OSTI]

    L. Iapichino; J. C. Niemeyer

    2008-07-01T23:59:59.000Z

    The development of turbulent gas flows in the intra-cluster medium and in the core of a galaxy cluster is studied by means of adaptive mesh refinement (AMR) cosmological simulations. A series of six runs was performed, employing identical simulation parameters but different criteria for triggering the mesh refinement. In particular, two different AMR strategies were followed, based on the regional variability of control variables of the flow and on the overdensity of subclumps, respectively. We show that both approaches, albeit with different results, are useful to get an improved resolution of the turbulent flow in the ICM. The vorticity is used as a diagnostic for turbulence, showing that the turbulent flow is not highly volume-filling but has a large area-covering factor, in agreement with previous theoretical expectations. The measured turbulent velocity in the cluster core is larger than 200 km/s, and the level of turbulent pressure contribution to the cluster hydrostatic equilibrium is increased by using the improved AMR criteria.

  18. Projected refined product balances in key Latin American countries: A preliminary examination

    SciTech Connect (OSTI)

    NONE

    1996-06-01T23:59:59.000Z

    Over the years, the East-West Center (EWC) has developed considerable expertise in refinery modeling, especially in the area of forecasting product balances for countries, given planned capacity changes, changes in product demand, changes in crude slates, and changes in product specifications. This expertise has been applied on an ongoing basis to the major refiners in the Middle East and the Asia-Pacific region, along with the US West Coast as region in its own right. Refinery modeling in these three areas has been ongoing for nearly 15 years at the Center, and the tools and information sources are now well developed. To date, the EWC has not applied these tools to Latin America. Although research on Latin America has been an ongoing area of concern at the Center in recent years, the information gathered to date is still not of the level of detail nor quality available for other areas. The modeling efforts undertaken in this report are of a ``baseline`` nature, designed to outline the major issues, attempt a first cut at emerging product balances, and, above all, to elicit commentary from those directly involved in the oil industry in the key countries modeled. Our experience in other regions has shown that it takes a few years dialogue with refiners and government planner in individual countries to develop a reliable database, as well as the insights into operational constraints and practices that make accurate modeling possible. This report is no more than a first step down the road.

  19. Conformation-dependent backbone geometry restraints set a new standard for protein crystallographic refinement

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Moriarty, Nigel W.; Tronrud, Dale E.; Adams, Paul D.; Karplus, P. Andrew

    2014-09-01T23:59:59.000Z

    Ideal values of bond angles and lengths used as external restraints are crucial for the successful refinement of protein crystal structures at all but the highest of resolutions. The restraints in common usage today have been designed based on the assumption that each type of bond or angle has a single ideal value independent of context. However, recent work has shown that the ideal values are, in fact, sensitive to local conformation, and as a first step toward using such information to build more accurate models, ultra-high resolution protein crystal structures have been used to derive a conformation-dependent library (CDL) of restraints for the protein backbone (Berkholz et al. 2009. Structure. 17, 1316). Here, we report the introduction of this CDL into the Phenix package and the results of test refinements of thousands of structures across a wide range of resolutions. These tests show that use of the conformation dependent library yields models that have substantially better agreement with ideal main-chain bond angles and lengths and, on average, a slightly enhanced fit to the X-ray data. No disadvantages of using the backbone CDL are apparent. In Phenix usage of the CDL can be selected by simply specifying the cdl=True option. This successful implementation paves the way for further aspects of the context-dependence of ideal geometry to be characterized and applied to improve experimental and predictive modelling accuracy.

  20. Solvent Refined Coal (SRC) process. Quarterly technical progress report, January 1979-March 1979

    SciTech Connect (OSTI)

    Not Available

    1980-02-01T23:59:59.000Z

    This report summarizes the progress of the Solvent Refined Coal (SRC) Project by the Pittsburg and Midway Coal Mining Co. for the Department of Energy for the period January 1, 1979 to March 31, 1979. Activities included the operation and modification of the Solvent Refined Coal Pilot Plant at Fort Lewis, Washington; the Process Development Unit P-99 at Harmarville, Pennsylvania; and research at Merriam Laboratory in Merriam, Kansas. The Pilot Plant processed Powhatan No. 5 Coal in the SRC-II mode of operation studying the effect of coal particle size and system temperature on coal slurry blending and the effect of carbon monoxide concentration in the reaction feed gas on process yields. January and February were spent completing installation of a fourth High Pressure Separator on Process Development Unit P-99 to better simulate operating conditions for the proposed Demonstration Plant. During March, one run was completed at P-99 feeding Pittsburgh Seam Coal from the Powhatan No. 5 Mine. Merriam investigations included a study of the effect of iron containing additives on SRC-I operation, the addition of carbon monoxide to the feed gas, utilization of a hydrogenated solvent (Cresap process solvent) in the SRC-I mode under both normal and short residence time operating conditions, and development of a simulated distillation technique to determine the entire boiling range distribution of product oils.

  1. Environmental-control considerations in the production and use of solvent-refined coal

    SciTech Connect (OSTI)

    Huang, H.S.

    1980-12-01T23:59:59.000Z

    This report presents the results of an environmental-control study of the solvent-refined-coal (SRC) process. The report complements a previous Argonne report: Assessment of Status of Technology for Solvent Refining of Coal (ANL/ECT-3, Appendix B). The current review separates discussion of environmental control into two broad sections: production of SRC fuels, both solid and liquid, and their utilization. Control technologies are briefly reviewed for the gas, liquid, and solid wastes generated by the production of SRC. For an SRC-I plant, producing solid product, potential waste streams are then identified and discussed in terms of applicable control technologies and promulgated EPA standards. The SRC-production section concludes with a discussion of the biological activity of certain products of an SRC-II plant, producing liquid fuel. The author summarizes recent experimental findings and recommends accelerated research at SRC plants to quantify the effects of biological activity and develop measures needed to reduce those effects. No unusual environmental-control problems have been detected in the combustion of SRC fuels. It is recommended, however, that more SRC combustion studies be made and that the solid and liquid fuels used in them be derived from a variety of parent coals. Such studies will establish the broad data base needed to demonstrate that SRC fuels burn efficiently within environmentally safe limits.

  2. Air UCI Summer Training Program in Environmental

    E-Print Network [OSTI]

    Nizkorodov, Sergey

    Air UCI Summer Training Program in Environmental Chemistry for Science Teachers I. July 11 ­ July · Lectures by AirUCI faculty · Lab tours of AirUCI laboratories · Follow-up for several years Distribution Models and predictions. Syllabus: Lectures Every AirUCI faculty member is actively involved

  3. Relative Ages of Globular Clusters

    E-Print Network [OSTI]

    Thomas H. Puzia

    2002-10-18T23:59:59.000Z

    Ages of extragalactic globular clusters can provide valuable insights into the formation and evolution of galaxies. In this contribution the photometric methods of age dating old globular cluster systems are summarised. The spectroscopic approach is reviewed with an emphasis of the right choice of age diagnostics. We present a new method of quantifying the relatively best age-sensitive spectroscopic index given the quality of a data set and a certain theoretical stellar synthesis model. The relatively best diagnostic plot is constructed from the set of Lick indices and used to age date globular clusters in several early-type galaxies which are part of a large spectroscopic survey of extragalactic globular cluster systems. We find that, independently of host galaxy, metal-poor ([Fe/H] 8 Gyr) and coeval. Metal-rich clusters show a wide range of ages from ~15 down to a few Gyr.

  4. Meteorological Effects on Air/Fuel Ratio

    E-Print Network [OSTI]

    Ferri, J. L.

    1984-01-01T23:59:59.000Z

    ) where subscript 1 indicates at condition 1 and subsc 1pt 2 Indicates at condition 2. Solving for E gives 2 100. (E . 13) Example 1 A furnace with a pressure type ratio control sys~em is calibrated at 10% excess air with 30 of air. If the air... of ... 30 of ... 460? 590 oR Substituting in Equation 13 and solving for E gives 2 E = (100 ... 10) (:;~)II, - 100 = 3.3% excess ir. 2 If the furnace had been calibrated to 10% excess air with iOO of air, the % excess air with 30 of air would bJI 590 II...

  5. Chapter 22: Compressed Air Evaluation Protocol

    SciTech Connect (OSTI)

    Benton, N.

    2014-11-01T23:59:59.000Z

    Compressed-air systems are used widely throughout industry for many operations, including pneumatic tools, packaging and automation equipment, conveyors, and other industrial process operations. Compressed-air systems are defined as a group of subsystems composed of air compressors, air treatment equipment, controls, piping, pneumatic tools, pneumatically powered machinery, and process applications using compressed air. A compressed-air system has three primary functional subsystems: supply, distribution, and demand. Air compressors are the primary energy consumers in a compressed-air system and are the primary focus of this protocol. The two compressed-air energy efficiency measures specifically addressed in this protocol are: high-efficiency/variable speed drive (VSD) compressor replacing modulating compressor; compressed-air leak survey and repairs. This protocol provides direction on how to reliably verify savings from these two measures using a consistent approach for each.

  6. AGING FACILITY WORKER DOSE ASSESSMENT

    SciTech Connect (OSTI)

    R.L. Thacker

    2005-03-24T23:59:59.000Z

    The purpose of this calculation is to estimate radiation doses received by personnel working in the Aging Facility performing operations to transfer aging casks to the aging pads for thermal and logistical management, stage empty aging casks, and retrieve aging casks from the aging pads for further processing in other site facilities. Doses received by workers due to aging cask surveillance and maintenance operations are also included. The specific scope of work contained in this calculation covers both collective doses and individual worker group doses on an annual basis, and includes the contributions due to external and internal radiation from normal operation. There are no Category 1 event sequences associated with the Aging Facility (BSC 2004 [DIRS 167268], Section 7.2.1). The results of this calculation will be used to support the design of the Aging Facility and to provide occupational dose estimates for the License Application. The calculations contained in this document were developed by Environmental and Nuclear Engineering of the Design and Engineering Organization and are intended solely for the use of the Design and Engineering Organization in its work regarding facility operation. Yucca Mountain Project personnel from the Environmental and Nuclear Engineering should be consulted before use of the calculations for purposes other than those stated herein or use by individuals other than authorized personnel in Environmental and Nuclear Engineering.

  7. Blind teen-age students' expectations Focus: school-age

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    Blind teen-age students' expectations Focus: school-age Topic: What are the changing demands disabled pupils, inclusion increased significantly, particularly in high schools. Blind learners, who used. For this lecture, I will present a few blind students' opinions, which will help building the items for the case

  8. Considering Air Density in Wind Power Production

    E-Print Network [OSTI]

    Zénó Farkas

    2011-03-11T23:59:59.000Z

    In the wind power production calculations the air density is usually considered as constant in time. Using the CIPM-2007 equation for the density of moist air as a function of air temperature, air pressure and relative humidity, we show that it is worth taking the variation of the air density into account, because higher accuracy can be obtained in the calculation of the power production for little effort.

  9. Air Pollution 7.1 INTRODUCTION

    E-Print Network [OSTI]

    Kammen, Daniel M.

    CHAPTER 7 Air Pollution 7.1 INTRODUCTION 7.2 OVERVIEW OF EMISSIONS 7.3 THE CLEAN AIR ACT 7.4 THE POLLUTANT STANDARDS INDEX 7.5 CRITERIA POLLUTANTS 7.6 TOXIC AIR POLLUTANTS 7.7 AIR POLLUTION IN THE WORLD'S MEGACITIES 7.8 MOTOR VEHICLE EMISSIONS 7.9 STATIONARY SOURCES 7.10 AIR POLLUTION AND METEOROLOGY 7

  10. Considering Air Density in Wind Power Production

    E-Print Network [OSTI]

    Farkas, Zénó

    2011-01-01T23:59:59.000Z

    In the wind power production calculations the air density is usually considered as constant in time. Using the CIPM-2007 equation for the density of moist air as a function of air temperature, air pressure and relative humidity, we show that it is worth taking the variation of the air density into account, because higher accuracy can be obtained in the calculation of the power production for little effort.

  11. Numerical Analysis of a Cold Air Distribution System

    E-Print Network [OSTI]

    Zhu, L.; Li, R.; Yuan, D.

    2006-01-01T23:59:59.000Z

    Cold air distribution systems may reduce the operating energy consumption of air-conditioned air supply system and improve the outside air volume percentages and indoor air quality. However, indoor temperature patterns and velocity field are easily...

  12. Residential Forced Air System Cabinet Leakage and Blower Performance

    E-Print Network [OSTI]

    Walker, Iain S.

    2010-01-01T23:59:59.000Z

    Driven Unitary  Air?Conditioning and Heat Pump Equipment”.  Air Conditioning &  Air?source Heat Pump Equipment.  Air?apply to the air handlers of heat pumps and electric 

  13. Managing aging in nuclear power plants: Insights from NRC maintenance team inspection reports

    SciTech Connect (OSTI)

    Fresco, A.; Subudhi, M.; Gunther, W.; Grove, E.; Taylor, J. [Brookhaven National Lab., Upton, NY (United States)

    1993-12-01T23:59:59.000Z

    A plant`s maintenance program is the principal vehicle through which age-related degradation is managed. From 1988 to 1991, the NRC evaluated the maintenance program of every nuclear power plant in the United States. Forty-four out of a total of 67 of the reports issued on these in-depth team inspections were reviewed for insights into the strengths and weaknesses of the programs as related to the need to understand and manage the effects of aging on nuclear plant systems, structures, and components. Relevant information was extracted from these inspection reports and sorted into several categories, including Specific Aging Insights, Preventive Maintenance, Predictive Maintenance and Condition Monitoring, Post Maintenance Testing, Failure Trending, Root Cause Analysis and Usage of Probabilistic Risk Assessment in the Maintenance Process. Specific examples of inspection and monitoring techniques successfully used by utilities to detect degradation due to aging have been identified. The information also was sorted according to systems and components, including: Auxiliary Feedwater, Main Feedwater, High Pressure Injection for both BWRs and PWRs, Service Water, Instrument Air, and Emergency Diesel Generator Air Start Systems, and Emergency Diesel Generators Air Start Systems, emergency diesel generators, electrical components such as switchgear, breakers, relays, and motor control centers, motor operated valves and check valves. This information was compared to insights gained from the Nuclear Plant Aging Research (NPAR) Program. Attributes of plant maintenance programs where the NRC inspectors felt that improvement was needed to properly address the aging issue also are discussed.

  14. Indoor Air Quality Poor indoor air quality comes from many sources. It can lead to having

    E-Print Network [OSTI]

    Indoor Air Quality Fact Sheet Poor indoor air quality comes from many sources. It can lead Indoor Air Pollutants · Molds · Pollen · Dander from pet fur · Secondhand smoke · Formaldehyde · Carbon such as cleaners and pesticides How to Improve Indoor Air Quality · Open windows when you can to let in fresh air

  15. About Nuccio Heating & Air Headquartered in Tampa, Florida, Nuccio Heating & Air serves

    E-Print Network [OSTI]

    Fisher, Kathleen

    a customer say, `you installed my first air conditioner - yourself!'" Nuccio Heating & Air serves commercialAbout Nuccio Heating & Air Headquartered in Tampa, Florida, Nuccio Heating & Air serves commercial ­ the majority being highly mobile ­ sell and service heating and air conditioning systems for the company

  16. Design Evolution Study - Aging Options

    SciTech Connect (OSTI)

    P. McDaniel

    2002-04-05T23:59:59.000Z

    The purpose of this study is to identify options and issues for aging commercial spent nuclear fuel received for disposal at the Yucca Mountain Mined Geologic Repository. Some early shipments of commercial spent nuclear fuel to the repository may be received with high-heat-output (younger) fuel assemblies that will need to be managed to meet thermal goals for emplacement. The capability to age as much as 40,000 metric tons of heavy metal of commercial spent nuclear he1 would provide more flexibility in the design to manage this younger fuel and to decouple waste receipt and waste emplacement. The following potential aging location options are evaluated: (1) Surface aging at four locations near the North Portal; (2) Subsurface aging in the permanent emplacement drifts; and (3) Subsurface aging in a new subsurface area. The following aging container options are evaluated: (1) Complete Waste Package; (2) Stainless Steel inner liner of the waste package; (3) Dual Purpose Canisters; (4) Multi-Purpose Canisters; and (5) New disposable canister for uncanistered commercial spent nuclear fuel. Each option is compared to a ''Base Case,'' which is the expected normal waste packaging process without aging. A Value Engineering approach is used to score each option against nine technical criteria and rank the options. Open issues with each of the options and suggested future actions are also presented. Costs for aging containers and aging locations are evaluated separately. Capital costs are developed for direct costs and distributable field costs. To the extent practical, unit costs are presented. Indirect costs, operating costs, and total system life cycle costs will be evaluated outside of this study. Three recommendations for aging commercial spent nuclear fuel--subsurface, surface, and combined surface and subsurface are presented for further review in the overall design re-evaluation effort. Options that were evaluated but not recommended are: subsurface aging in a new subsurface area (high cost); surface aging in the complete waste package (risk to the waste package and impact on the Waste Handling Facility); and aging in the stainless steel liner (impact on the waste package design and new high risk operations added to the waste packaging process). The selection of a design basis for aging will be made in conjunction with the other design re-evaluation studies.

  17. Aging behavior of polymeric solar absorber materials - Part 1: Engineering plastics

    SciTech Connect (OSTI)

    Kahlen, S. [Polymer Competence Center Leoben GmbH, Roseggerstrasse 12, Leoben 8700 (Austria); Wallner, G.M.; Lang, R.W. [Institute for Polymeric Materials and Testing, University of Linz, Altenbergerstrasse 69, Linz 4040 (Austria)

    2010-09-15T23:59:59.000Z

    In this series of two papers, various polymeric materials are investigated as to their potential applicability as absorber materials for solar thermal collectors. The focus of the investigation is to study the aging behavior of these materials under maximum operating conditions (80 C in water up to 16,000 h) and stagnation conditions (140 C in air up to 500 h) typical for northern climate. The materials supplied or produced as polymer films were first characterized in the unaged state and then for different states of aging by differential scanning calorimetry (DSC), by size exclusion chromatography (SEC) and by mechanical tensile tests. Physical aging phenomena were studied by DSC, SEC analysis provided information on chemical degradation of the materials. In addition, physical and chemical aging were both analyzed via the small and large strain mechanical behavior. While the present Part 1 of this paper series deals with the aging behavior of engineering plastics, including two amorphous polymers (a polyphenylene ether polystyrene blend (PPE + PS) and polycarbonate (PC)) and two semi-crystalline polymers (two types of polyamide 12 (PA12)), the aging behavior of so-called ''commodity'' plastics (PE and PP) is the subject of Part 2. Comparing the two aging conditions, the amorphous materials (PPE + PS and PC) turned out to be more prone to physical and chemical aging at 140 C in air. In contrast, the semi-crystalline PA12 materials were more strongly affected by exposure to water at 80 C, although to different degrees, depending on the modification. (author)

  18. High Energy Efficiency Air Conditioning

    SciTech Connect (OSTI)

    Edward McCullough; Patrick Dhooge; Jonathan Nimitz

    2003-12-31T23:59:59.000Z

    This project determined the performance of a new high efficiency refrigerant, Ikon B, in a residential air conditioner designed to use R-22. The refrigerant R-22, used in residential and small commercial air conditioners, is being phased out of production in developed countries beginning this year because of concerns regarding its ozone depletion potential. Although a replacement refrigerant, R-410A, is available, it operates at much higher pressure than R-22 and requires new equipment. R-22 air conditioners will continue to be in use for many years to come. Air conditioning is a large part of expensive summer peak power use in many parts of the U.S. Previous testing and computer simulations of Ikon B indicated that it would have 20 - 25% higher coefficient of performance (COP, the amount of cooling obtained per energy used) than R-22 in an air-cooled air conditioner. In this project, a typical new R-22 residential air conditioner was obtained, installed in a large environmental chamber, instrumented, and run both with its original charge of R-22 and then with Ikon B. In the environmental chamber, controlled temperature and humidity could be maintained to obtain repeatable and comparable energy use results. Tests with Ikon B included runs with and without a power controller, and an extended run for several months with subsequent analyses to check compatibility of Ikon B with the air conditioner materials and lubricant. Baseline energy use of the air conditioner with its original R-22 charge was measured at 90 deg F and 100 deg F. After changeover to Ikon B and a larger expansion orifice, energy use was measured at 90 deg F and 100 deg F. Ikon B proved to have about 19% higher COP at 90 deg F and about 26% higher COP at 100 deg F versus R-22. Ikon B had about 20% lower cooling capacity at 90 deg F and about 17% lower cooling capacity at 100 deg F versus R-22 in this system. All results over multiple runs were within 1% relative standard deviation (RSD). All of these values agree well with previous results and computer simulations of Ikon B performance versus R-22. The lower cooling capacity of Ikon B is not a concern unless a particular air conditioner is near its maximum cooling capacity in application. Typically, oversized A/C systems are installed by contractors to cover contingencies. In the extended run with Ikon B, which lasted about 4.5 months at 100 deg F ambient temperature and 68% compressor on time, the air conditioner performed well with no significant loss of energy efficiency. Post-run analysis of the refrigerant, compressor lubricant oil, compressor, compressor outlet tubing, and the filter/dryer showed minor effects but nothing that was considered significant. The project was very successful. All objectives were achieved, and the performance of Ikon B indicates that it can easily be retrofitted into R-22 air conditioners to give 15 - 20% energy savings and a 1 - 3 year payback of retrofit costs depending on location and use. Ikon B has the potential to be a successful commercial product.

  19. The Air-Fluorescence Yield

    E-Print Network [OSTI]

    F. Arqueros; F. Blanco; D. Garcia-Pinto; M. Ortiz; J. Rosado

    2008-07-30T23:59:59.000Z

    Detection of the air-fluorescence radiation induced by the charged particles of extensive air showers is a well-established technique for the study of ultra-high energy cosmic rays. Fluorescence telescopes provide a nearly calorimetric measure of the primary energy. Presently the main source of systematic uncertainties comes from our limited accuracy in the fluorescence yield, that is, the number of fluorescence photons emitted per unit of energy deposited in the atmosphere by the shower particles. In this paper the current status of our knowledge on the fluorescence yield both experimental an theoretical will be discussed.

  20. Leads Tactical Air Control Party (TACP) and Air Support

    E-Print Network [OSTI]

    Duchowski, Andrew T.

    leadership in the demanding environment of Joint operations -Meet medical standards for Ground Based Control as an ALO. Joint Air Operations Command and Control Course: The JAOC2C will provide the 13L ALO an overview, Ranger School, the Joint Operational Fires and Effects Course, and others. initiAL trAining AdvAnced tr

  1. Aging and iodine loading of silver-functionalized aerogels

    SciTech Connect (OSTI)

    Bruffey, S.H.; Jubin, R.T.; Anderson, K.K.; Walker, J.F. [Oak Ridge National Laboratory, P.O. Box 2008, MS-6223, Oak Ridge, TN 37831 (United States)

    2013-07-01T23:59:59.000Z

    Engineered silver-functionalized silica aerogels are being investigated for their potential application in off-gas treatment at a used nuclear fuel reprocessing facility. Reprocessing will release several key volatile radionuclides, including iodine-129. To achieve regulatory compliance, iodine-129 must be removed from any off-gas stream prior to environmental discharge. Ag{sup 0}-functionalized aerogels have been demonstrated to have high iodine-capture capacity, high porosity, and potential for conversion into a waste form. Capture materials used in off-gas treatment may be exposed to a heated, high-humidity, acidic gas stream for months. Extended exposure to this stream could affect sorbent performance. It was the aim of this study to evaluate what impacts might be observed when Ag{sup 0}-functionalized aerogels prepared at Pacific Northwest National Laboratory were contacted with a dry air stream for up to 6 months and then used to adsorb iodine from a synthetic off-gas stream. Results demonstrate that there is some loss of iodine-capture capacity caused by aging, but that this loss is not as marked as for aging of more traditional iodine sorbents, such as silver-impregnated mordenite. Specifically, aging silver-functionalized aerogel under a dry air stream for up to 6 months can decrease its iodine capacity from 41 wt% to 32 wt%. (authors)

  2. AGING AND IODINE LOADING OF SILVER-FUNCTIONALIZED AEROGELS

    SciTech Connect (OSTI)

    Bruffey, Stephanie H [ORNL; Jubin, Robert Thomas [ORNL; Anderson, Kaara K [ORNL; Walker Jr, Joseph Franklin [ORNL

    2013-01-01T23:59:59.000Z

    Engineered silver-functionalized silica aerogels are being investigated for their application in off-gas treatment at a used nuclear fuel reprocessing facility. Reprocessing will release several key volatile radionuclides, including iodine-129. To achieve regulatory compliance, iodine-129 must be removed from any off-gas stream prior to environmental discharge. Silver-functionalized aerogels have been demonstrated to have high iodine capture capacity, high porosity and potential for conversion into a waste form. Capture materials used in off-gas treatment may be exposed to a heated, high humidity, acidic gas stream for months. Extended exposure to this stream could affect sorbent performance. It was the aim of this study to evaluate what impacts might be observed when Ag0-functionalized aerogels prepared at Pacific Northwest National Laboratory were contacted with a dry air stream for up to 6 months and then used to adsorb iodine from a synthetic off-gas stream. Results demonstrate that there is some loss of iodine capture capacity caused by aging, but that this loss is not as marked as for aging of more traditional iodine sorbents, such as silver-impregnated mordenite. Specifically, aging silver-functionalized aerogel under a dry air stream for up to 6 months can decrease its iodine capacity from 41wt% to 32wt%.

  3. Improving macromolecular atomic models at moderate resolution by automated iterative model building, statistical density modification and refinement

    SciTech Connect (OSTI)

    Terwilliger, Thomas C., E-mail: terwilliger@lanl.gov [Mail Stop M888, Los Alamos National Laboratory, Los Alamos, NM 87545 (United States)

    2003-07-01T23:59:59.000Z

    A procedure for iterative model-building, statistical density modification and refinement at moderate resolution (up to about 2.8 Å) is described. An iterative process for improving the completeness and quality of atomic models automatically built at moderate resolution (up to about 2.8 Å) is described. The process consists of cycles of model building interspersed with cycles of refinement and combining phase information from the model with experimental phase information (if any) using statistical density modification. The process can lead to substantial improvements in both the accuracy and completeness of the model compared with a single cycle of model building. For eight test cases solved by MAD or SAD at resolutions ranging from 2.0 to 2.8 Å, the fraction of models built and assigned to sequence was 46–91% (mean of 65%) after the first cycle of building and refinement, and 78-95% (mean of 87%) after 20 cycles. In an additional test case, an incorrect model of gene 5 protein (PDB code 2gn5; r.m.s.d. of main-chain atoms from the more recent refined structure 1vqb at 1.56 Å) was rebuilt using only structure-factor amplitude information at varying resolutions from 2.0 to 3.0 Å. Rebuilding was effective at resolutions up to about 2.5 Å. The resulting models had 60-80% of the residues built and an r.m.s.d. of main-chain atoms from the refined structure of 0.20 to 0.62 Å. The algorithm is useful for building preliminary models of macromolecules suitable for an experienced crystallographer to extend, correct and fully refine.

  4. Air quality, infant mortality, and the Clean Air Act of 1970

    E-Print Network [OSTI]

    Chay, Kenneth Y.

    2003-01-01T23:59:59.000Z

    We examine the effects of total suspended particulates (TSPs) air pollution on infant health using the air quality improvements induced by the 1970 Clean Air Act Amendments (CAAA). This legislation imposed strict regulations ...

  5. Review: Clearing the Air: The Health and Economic Damages of Air Pollution in China

    E-Print Network [OSTI]

    Lee, Joseph

    2009-01-01T23:59:59.000Z

    and Economic Damages of Air Pollution in China Mun S. Ho andEconomic Damages of Air Pollution in China. Cambridge, MA:the assessment of air pollution and its health and economic

  6. AIR QUALITY IMPACTS OF LIQUEFIED NATURAL GAS IN THE SOUTH COAST AIR BASIN OF CALIFORNIA

    E-Print Network [OSTI]

    Carerras-Sospedra, Marc

    2012-01-01T23:59:59.000Z

    Emissions 7.3 Impacts of LNG on Air Quality 8. References 9.El Paso at Blythe. Chapter 3: Air Quality Impact AssessmentRespect to the South Coast Air Quality Management District

  7. Refined model of the {Fe9} magnetic molecule from low-temperature inelastic neutron scattering studies

    SciTech Connect (OSTI)

    Engelhardt, Larry [Francis Marion University; Demmel, Franz [Rutherford Appleton Laboratory; Luban, Marshall [Ames Laboratory; Timco, Grigore A [The University of Manchester; Tuna, Floriana [The University of Manchester; Winpenny, Richard E [The University of Manchester

    2014-06-01T23:59:59.000Z

    We present a refined model of the {Fe9} tridiminished icosahedron magnetic molecule system. This molecule was originally modeled as being composed of two ({Fe3} and {Fe6}) clusters, with the Fe3+ ions within each cluster being coupled via exchange interactions, but with no coupling between the clusters. The present inelastic neutron scattering (INS) measurements were used to probe the low-lying energy spectrum of {Fe9}, and these results demonstrate that the previously published model of two uncoupled clusters is incomplete. To achieve agreement between the experiment and theory, we have augmented the model with relatively small exchange coupling between the clusters. A combination of Lanczos matrix diagonalization and quantum Monte Carlo simulations have been used to achieve good agreement between the experimental data and the improved model of the full {Fe9} system despite the complexity of this model (with Hilbert space dimension >107).

  8. Dynamic Implicit 3D Adaptive Mesh Refinement for Non-Equilibrium Radiation Diffusion

    SciTech Connect (OSTI)

    Philip, Bobby [ORNL] [ORNL; Wang, Zhen [ORNL] [ORNL; Berrill, Mark A [ORNL] [ORNL; Rodriguez Rodriguez, Manuel [ORNL] [ORNL; Pernice, Michael [Idaho National Laboratory (INL)] [Idaho National Laboratory (INL)

    2014-01-01T23:59:59.000Z

    The time dependent non-equilibrium radiation diffusion equations are important for solving the transport of energy through radiation in optically thick regimes and find applications in several fields including astrophysics and inertial confinement fusion. The associated initial boundary value problems that are encountered exhibit a wide range of scales in space and time and are extremely challenging to solve. To efficiently and accurately simulate these systems we describe our research on combining techniques that will also find use more broadly for long term time integration of nonlinear multiphysics systems: implicit time integration for efficient long term time integration of stiff multiphysics systems, local control theory based step size control to minimize the required global number of time steps while controlling accuracy, dynamic 3D adaptive mesh refinement (AMR) to minimize memory and computational costs, Jacobian Free Newton Krylov methods on AMR grids for efficient nonlinear solution, and optimal multilevel preconditioner components that provide level independent linear solver convergence.

  9. Refinement of the twinned structure of cymrite from the Ruby Creek deposit (Alaska)

    SciTech Connect (OSTI)

    Bolotina, N. B.; Rastsvetaeva, R. K., E-mail: rast@ns.crys.ras.ru; Kashaev, A. A. [Russian Academy of Sciences, Shubnikov Institute of Crystallography (Russian Federation)

    2010-07-15T23:59:59.000Z

    The mineral cymrite from the Ruby Creek deposit (Alaska) was reinvestigated by X-ray diffraction in a pseudo-orthorhombic unit cell with a = 5.3350(1) A, b = 36.9258(8) A, c = 7.6934(1) A, {beta} = 90.00(1){sup o}. A twin law corresponding to a sixfold axis was revealed for the first time. The structure was refined in the monoclinic space group P12{sub 1}1 to the R factor of 5.4%. The Al and Si atoms are assumed to be ordered within a double layer. The rotation of the cation sublattice by 60{sup o} around the c axis leads to the disorder of the T sites in the crystal structure (T = Al, Si).

  10. Development of the electron beam melting and refining in the Eastern Europe

    SciTech Connect (OSTI)

    Mladenov, G.M. [Institute of Electronics, Sofia (Bulgaria)

    1994-12-31T23:59:59.000Z

    A open research potential for the many R & D projects, as well as developed industrial structures exist in the Central and Eastern Europe countries. Now the economy crisis in this part of the world, due to the positive exiting democratic changes and to the transition from central planned to the market economy are a challenge. Bridging the research and industrial potential of the Eastern Europe to the developed economies is a way to keep the knowledge and people with activity in this field and to extend the future market of EB products. A brief revue of the institutions and a very short general information for the EB melting and refinement development in the Eastern Europe countries is given.

  11. Proceedings of the conference on electron beam melting and refining - state of the art 1994

    SciTech Connect (OSTI)

    Bakish, R. [ed.

    1994-12-31T23:59:59.000Z

    The volume: Proceedings of the Conference on Electron Beam Melting and Refining-State of the Art 1994 covers many aspects of electron beam production, process control, components, and applications. Included were several papers from the defunct Soviet Bloc nations concerning the specifications and uses for their electron beam furnaces. Main topics of the conference were: Electron Beam (EB) Equipment; Safety and Analytical Aspects related to EB Melting; Material Processing with EB; Other Applications for EB; and A Look at EB in the East. EB has many uses, several papers mentioned the recycling of uranium scrap, the casting of heat resistant or corrosion resistant alloys, or the improved microstructure of alloys with the technique.

  12. Iterative build OMIT maps: Map improvement by iterative model-building and refinement without model bias

    SciTech Connect (OSTI)

    Los Alamos National Laboratory, Mailstop M888, Los Alamos, NM 87545, USA; Lawrence Berkeley National Laboratory, One Cyclotron Road, Building 64R0121, Berkeley, CA 94720, USA; Department of Haematology, University of Cambridge, Cambridge CB2 0XY, England; Terwilliger, Thomas; Terwilliger, T.C.; Grosse-Kunstleve, Ralf Wilhelm; Afonine, P.V.; Moriarty, N.W.; Zwart, P.H.; Hung, L.-W.; Read, R.J.; Adams, P.D.

    2008-02-12T23:59:59.000Z

    A procedure for carrying out iterative model-building, density modification and refinement is presented in which the density in an OMIT region is essentially unbiased by an atomic model. Density from a set of overlapping OMIT regions can be combined to create a composite 'Iterative-Build' OMIT map that is everywhere unbiased by an atomic model but also everywhere benefiting from the model-based information present elsewhere in the unit cell. The procedure may have applications in the validation of specific features in atomic models as well as in overall model validation. The procedure is demonstrated with a molecular replacement structure and with an experimentally-phased structure, and a variation on the method is demonstrated by removing model bias from a structure from the Protein Data Bank.

  13. Astrophysical hydrodynamics with a high-order discontinuous Galerkin scheme and adaptive mesh refinement

    E-Print Network [OSTI]

    Schaal, Kevin; Chandrashekar, Praveen; Pakmor, Rüdiger; Klingenberg, Christian; Springel, Volker

    2015-01-01T23:59:59.000Z

    Solving the Euler equations of ideal hydrodynamics as accurately and efficiently as possible is a key requirement in many astrophysical simulations. It is therefore important to continuously advance the numerical methods implemented in current astrophysical codes, especially also in light of evolving computer technology, which favours certain computational approaches over others. Here we introduce the new adaptive mesh refinement (AMR) code TENET, which employs a high-order Discontinuous Galerkin (DG) scheme for hydrodynamics. The Euler equations in this method are solved in a weak formulation with a polynomial basis by means of explicit Runge-Kutta time integration and Gauss-Legendre quadrature. This approach offers significant advantages over commonly employed finite volume (FV) solvers. In particular, the higher order capability renders it computationally more efficient, in the sense that the same precision can be obtained at significantly less computational cost. Also, the DG scheme inherently conserves a...

  14. Lance for fuel and oxygen injection into smelting or refining furnace

    DOE Patents [OSTI]

    Schlichting, M.R.

    1994-12-20T23:59:59.000Z

    A furnace for smelting iron ore and/or refining molten iron is equipped with an overhead pneumatic lance, through which a center stream of particulate coal is ejected at high velocity into a slag layer. An annular stream of nitrogen or argon enshrouds the coal stream. Oxygen is simultaneously ejected in an annular stream encircling the inert gas stream. The interposition of the inert gas stream between the coal and oxygen streams prevents the volatile matter in the coal from combusting before it reaches the slag layer. Heat of combustion is thus more efficiently delivered to the slag, where it is needed to sustain the desired reactions occurring there. A second stream of lower velocity oxygen can be delivered through an outermost annulus to react with carbon monoxide gas rising from slag layer, thereby adding still more heat to the furnace. 7 figures.

  15. 3D Adaptive Mesh Refinement Simulations of Pellet Injection in Tokamaks

    SciTech Connect (OSTI)

    R. Samtaney; S.C. Jardin; P. Colella; D.F. Martin

    2003-10-20T23:59:59.000Z

    We present results of Adaptive Mesh Refinement (AMR) simulations of the pellet injection process, a proven method of refueling tokamaks. AMR is a computationally efficient way to provide the resolution required to simulate realistic pellet sizes relative to device dimensions. The mathematical model comprises of single-fluid MHD equations with source terms in the continuity equation along with a pellet ablation rate model. The numerical method developed is an explicit unsplit upwinding treatment of the 8-wave formulation, coupled with a MAC projection method to enforce the solenoidal property of the magnetic field. The Chombo framework is used for AMR. The role of the E x B drift in mass redistribution during inside and outside pellet injections is emphasized.

  16. End of the Little Ice Age in the Alps forced by industrial black carbon

    E-Print Network [OSTI]

    Marzeion, Ben

    , Oceanic, and Space Sciences, University of Michigan, Ann Arbor, MI 48109; c Institute of MeteorologyEnd of the Little Ice Age in the Alps forced by industrial black carbon Thomas H. Paintera,1 , Mark and Geophysics, University of Innsbruck, 6020 Innsbruck, Austria; d Air Quality Research Center, University

  17. Effects of Thermal Aging on the Mechanical Properties of a Porous-Matrix Ceramic Composite

    E-Print Network [OSTI]

    Zok, Frank

    Effects of Thermal Aging on the Mechanical Properties of a Porous-Matrix Ceramic Composite Eric A of 1000­1200°C in air. The composite of interest derives its damage tolerance from a highly porous matrix, precluding the need for an interphase at the fiber­matrix boundary. The key issue in- volves the stability

  18. Development of a performance-based industrial energy efficiency indicator for corn refining plants.

    SciTech Connect (OSTI)

    Boyd, G. A.; Decision and Information Sciences; USEPA

    2006-07-31T23:59:59.000Z

    Organizations that implement strategic energy management programs have the potential to achieve sustained energy savings if the programs are carried out properly. A key opportunity for achieving energy savings that plant managers can take is to determine an appropriate level of energy performance by comparing their plant's performance with that of similar plants in the same industry. Manufacturing facilities can set energy efficiency targets by using performance-based indicators. The U.S. Environmental Protection Agency (EPA), through its ENERGY STAR{reg_sign} program, has been developing plant energy performance indicators (EPIs) to encourage a variety of U.S. industries to use energy more efficiently. This report describes work with the corn refining industry to provide a plant-level indicator of energy efficiency for facilities that produce a variety of products--including corn starch, corn oil, animal feed, corn sweeteners, and ethanol--for the paper, food, beverage, and other industries in the United States. Consideration is given to the role that performance-based indicators play in motivating change; the steps needed to develop indicators, including interacting with an industry to secure adequate data for an indicator; and the actual application and use of an indicator when complete. How indicators are employed in the EPA's efforts to encourage industries to voluntarily improve their use of energy is discussed as well. The report describes the data and statistical methods used to construct the EPI for corn refining plants. Individual equations are presented, as are the instructions for using them in an associated Excel spreadsheet.

  19. Synthesis and single crystal structure refinement of the one-layer hydrate of sodium brittle mica

    SciTech Connect (OSTI)

    Kalo, Hussein; Milius, Wolfgang [Lehrstuhl fuer Anorganische Chemie I, University of Bayreuth, D-95440 Bayreuth (Germany)] [Lehrstuhl fuer Anorganische Chemie I, University of Bayreuth, D-95440 Bayreuth (Germany); Braeu, Michael [BASF Construction Chemicals GmbH, 83308 Trostberg (Germany)] [BASF Construction Chemicals GmbH, 83308 Trostberg (Germany); Breu, Josef, E-mail: Josef.Breu@uni-bayreuth.de [Lehrstuhl fuer Anorganische Chemie I, University of Bayreuth, D-95440 Bayreuth (Germany)] [Lehrstuhl fuer Anorganische Chemie I, University of Bayreuth, D-95440 Bayreuth (Germany)

    2013-02-15T23:59:59.000Z

    A sodium brittle mica with the ideal composition [Na{sub 4}]{sup inter}[Mg{sub 6}]{sup oct}[Si{sub 4}Al{sub 4}]{sup tet}O{sub 20}F{sub 4} was synthesized via melt synthesis in a gas tight crucible. This mica is unusual inasmuch as the known mica structure holds only room for two interlayer cations per unit cell and inasmuch as it readily hydrates despite the high layer charge while ordinary micas and brittle micas are non-swelling. The crystal structure of one-layer hydrate sodium brittle mica was determined and refined from single crystal X-ray data. Interlayer cations reside at the center of the distorted hexagonal cavities and are coordinated by the three inner basal oxygen atoms. The coordination of the interlayer cation is completed by three interlayer water molecules residing at the center of the interlayer region. The relative position of adjacent 2:1-layers thus is fixed by these octahedrally coordinated interlayer cations. Pseudo-symmetry leads to extensive twinning. In total five twin operations generate the same environment for the interlayer species and are energetically degenerate. - Graphical abstract: The sodium brittle mica has been successfully synthesized by melt synthesis and the crystal structure of the one-layer hydrate of sodium brittle mica was determined from single crystal X-ray diffraction data. Highlights: Black-Right-Pointing-Pointer Melt synthesis yielded coarse grained sodium brittle mica which showed little disorder. Black-Right-Pointing-Pointer Sodium brittle mica hydrated completely to the state of one-layer hydrate. Black-Right-Pointing-Pointer Structure of one-layer hydrate of sodium brittle mica could therefore be determined and refined. Black-Right-Pointing-Pointer Arrangement of upper and lower tetrahedral sheet encompassing interlayer cation were clarified.

  20. An enriched finite element model with q-refinement for radiative boundary layers in glass cooling

    SciTech Connect (OSTI)

    Mohamed, M. Shadi [Institute for Infrastructure and Environment, Heriot-Watt University, Edinburgh EH14 4AS (United Kingdom)] [Institute for Infrastructure and Environment, Heriot-Watt University, Edinburgh EH14 4AS (United Kingdom); Seaid, Mohammed; Trevelyan, Jon [School of Engineering and Computing Sciences, University of Durham, South Road, Durham DH1 3LE (United Kingdom)] [School of Engineering and Computing Sciences, University of Durham, South Road, Durham DH1 3LE (United Kingdom); Laghrouche, Omar [Institute for Infrastructure and Environment, Heriot-Watt University, Edinburgh EH14 4AS (United Kingdom)] [Institute for Infrastructure and Environment, Heriot-Watt University, Edinburgh EH14 4AS (United Kingdom)

    2014-02-01T23:59:59.000Z

    Radiative cooling in glass manufacturing is simulated using the partition of unity finite element method. The governing equations consist of a semi-linear transient heat equation for the temperature field and a stationary simplified P{sub 1} approximation for the radiation in non-grey semitransparent media. To integrate the coupled equations in time we consider a linearly implicit scheme in the finite element framework. A class of hyperbolic enrichment functions is proposed to resolve boundary layers near the enclosure walls. Using an industrial electromagnetic spectrum, the proposed method shows an immense reduction in the number of degrees of freedom required to achieve a certain accuracy compared to the conventional h-version finite element method. Furthermore the method shows a stable behaviour in treating the boundary layers which is shown by studying the solution close to the domain boundaries. The time integration choice is essential to implement a q-refinement procedure introduced in the current study. The enrichment is refined with respect to the steepness of the solution gradient near the domain boundary in the first few time steps and is shown to lead to a further significant reduction on top of what is already achieved with the enrichment. The performance of the proposed method is analysed for glass annealing in two enclosures where the simplified P{sub 1} approximation solution with the partition of unity method, the conventional finite element method and the finite difference method are compared to each other and to the full radiative heat transfer as well as the canonical Rosseland model.

  1. Effect of Return Air Leakage on Air Conditioner Performance in Hot/Humid Climates 

    E-Print Network [OSTI]

    O'Neal, D. L.; Rodriguez, A.; Davis, M.; Kondepudi, S.

    1996-01-01T23:59:59.000Z

    provided rebates to residential customers for purchasing high efficiency air conditioners and heat pumps. The rebates have helped increase the demand for higher efficiency air conditioning units. However, even the most efficient system will not perform... quanm the effect of air leakage in the return air duct from a hot attic space on the high-temperature performance of air conditioners and heat pump systems. Air conditioner performance is quantified in terms of capacity, Energy Efficiency Ratio (EER...

  2. Air Capture Introduction and Overview

    E-Print Network [OSTI]

    first." It is much cheaper to capture CO2 from the flue gas of a coal power plant than from ambient air largely eliminated centralized sources of CO2 emissions, especially at coal and natural gas power plants of a facility that captures CO2 from the flue gas of a coal power plant, keeping all possible assumptions

  3. I) EXAS AIR CONTROL BLAR

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    I) EXAS AIR CONTROL BLAR 6330 HWY. 290 EAST, AUSTIN, TEXAS 78723, 512451-5711 DICK WHmINGTON, P.E. JOHN L. BLAIR CHAIRMAN MARCUS M. KEY, M.D. CALVIN 8. PARNELL, JR., Ph.D., P.E....

  4. Micromachinable Leaky Wave Air Transducers

    E-Print Network [OSTI]

    Khuri-Yakub, Butrus T. "Pierre"

    reflection coefficient can also in a thin plate as a meam of efficient coupling of ultrasonic energy to air of the ultrasonic energy is a function of the elastic properties of the plate andmost dominantly determinedby lowerleak rates as compared to silicon and aluminum. Since these thin dates aremuch easier to fabricate wine

  5. Lead reduction in ambient air

    SciTech Connect (OSTI)

    Smith, R.D.; Kiehn, O.A.; Wilburn, D.R.; Bowyer, R.C.

    1987-01-01T23:59:59.000Z

    The Bureau of Mines evaluated the emission control methods, including the capital investments and operating cost, necessary for further reducing lead levels in ambient air at the Glover, Herculaneum, and Buick smelter-refineries in Missouri and the East Helena, MT, smelter. This report presents theoretically achievable lead emission reductions and estimated capital and operating costs.

  6. CATEE: Clean Air Through Energy Efficiency Conference

    E-Print Network [OSTI]

    Tillman, S.

    2014-01-01T23:59:59.000Z

    and musts often resort to drugs to alleviate symptoms. • Research shows that people spend over 50% of their time at home indoors. • Consumer awareness of IAQ is growing Why IAQ Matters © 2014 CirrusAir Technologies, Inc Sources: EPA, State of the Air... • Household cleaners © 2014 CirrusAir Technologies, Inc ESL-KT-14-11-27 CATEE 2014: Clean Air Through Efficiency Conference, Dallas, Texas Nov. 18-20 Current Filtration Systems © 2014 CirrusAir Technologies, Inc • The increased need for indoor air quality...

  7. Proceedings of the International Workshop on inspection and evaluation of aging aircraft

    SciTech Connect (OSTI)

    Not Available

    1993-01-01T23:59:59.000Z

    Economics is the key issue in a discussion on the inspection of aging aircraft. The airline industry has taken heavy losses resulting in layoffs and bankruptcies in recent years. Improving air service to customers is the ultimate reason for conducting research on the effects of aging on aircraft, but cost must be taken into account for the effective implementation of inspection programs. These papers present state of the art research to predict, detect, define, and correct the effects of age and usage on the metals and materials used in construction of aircraft and powerplants. Individual papers are abstracted separately.

  8. aging society aging: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    3 Age CiteSeer Summary: Success in school can be a positive counterweight to the abuse, neglect, separation, and impermanence experienced by the more than 400,000 U.S....

  9. Air sampling in the workplace. Final report

    SciTech Connect (OSTI)

    Hickey, E.E.; Stoetzel, G.A.; Strom, D.J.; Cicotte, G.R. [Pacific Northwest Lab., Richland, WA (United States); Wiblin, C.M. [Advanced Systems Technology, Inc., Atlanta, GA (United States); McGuire, S.A. [Nuclear Regulatory Commission, Washington, DC (United States). Div. of Regulatory Applications

    1993-09-01T23:59:59.000Z

    This report provides technical information on air sampling that will be useful for facilities following the recommendations in the NRC`s Regulatory Guide 8.25, Revision 1, ``Air sampling in the Workplace.`` That guide addresses air sampling to meet the requirements in NRC`s regulations on radiation protection, 10 CFR Part 20. This report describes how to determine the need for air sampling based on the amount of material in process modified by the type of material, release potential, and confinement of the material. The purposes of air sampling and how the purposes affect the types of air sampling provided are discussed. The report discusses how to locate air samplers to accurately determine the concentrations of airborne radioactive materials that workers will be exposed to. The need for and the methods of performing airflow pattern studies to improve the accuracy of air sampling results are included. The report presents and gives examples of several techniques that can be used to evaluate whether the airborne concentrations of material are representative of the air inhaled by workers. Methods to adjust derived air concentrations for particle size are described. Methods to calibrate for volume of air sampled and estimate the uncertainty in the volume of air sampled are described. Statistical tests for determining minimum detectable concentrations are presented. How to perform an annual evaluation of the adequacy of the air sampling is also discussed.

  10. Evaluation of workplace air monitoring locations

    SciTech Connect (OSTI)

    Stoetzel, G.A.; Cicotte, G.R.; Lynch, T.P. (Pacific Northwest Lab., Richland, WA (United States)); Aldrich, L.K. (Westinghouse Hanford Co., Richland, WA (United States))

    1991-10-01T23:59:59.000Z

    Current federal guidance on occupational radiation protection recognizes the importance of conducting air flow studies to assist in the placement of air sampling and monitoring equipment. In support of this, Pacific Northwest Laboratory has provided technical assistance to Westinghouse Hanford Company for the purpose of evaluating the adequacy of air sampling and monitoring locations at selected Hanford facilities. Qualitative air flow studies were performed using smoke aerosols to visually determine air movement. Three examples are provided of how air flow studies results, along with information on the purpose of the air sample being collected, were used as a guide in placing the air samplers and monitors. Preparatory steps in conducting an air flow study should include: (1) identifying type of work performed in the work area including any actual or potential release points; (2) determining the amounts of radioactive material available for release and its chemical and physical form; (3) obtaining accurate work area descriptions and diagrams; (4) identifying the location of existing air samplers and monitors; (5) documenting physical and ventilation configurations; (6) notifying appropriate staff of the test; and (7) obtaining necessary equipment and supplies. The primary steps in conducting an air flow study are measurements of air velocities in the work area, release of the smoke aerosol at selected locations in the work area and the observation of air flow patterns, and finally evaluation and documentation of the results. 2 refs., 3 figs.

  11. NO2 Aging and Iodine Loading of Silver-Functionalized Aerogels

    SciTech Connect (OSTI)

    Patton, K K [ORNL; Bruffey, S H [ORNL; Walker, J F [ORNL; Jubin, R T [ORNL

    2014-07-31T23:59:59.000Z

    Off-gas treatment systems in used fuel reprocessing which use fixed-bed adsorbers are typically designed to operate for an extended period of time before replacement or regeneration of the adsorbent. During this time, the sorbent material will be exposed to the off-gas stream. Exposure could last for months, depending on the replacement cycle time. The gas stream will be at elevated temperature and will possibly contain a mixture of water vapor, NOx, nitric acid vapors, and a variety of other constituents in addition to the radionuclides of capture interest. A series of studies were undertaken to evaluate the effects of long-term exposure, or aging, on proposed iodine sorbent materials under increasingly harsh off-gas conditions. Previous studies have evaluated the effects of up to 6 months of aging under dry air and under humid air conditions on the iodine loading behavior of Ag0-functionalized aerogels. This study examines the effects of extended exposure (up to 6 months) to NO2 on the iodine loading capacity of Ag0- functionalized aerogels. Material aged for 1 and 2 months appeared to have a similar total loading capacity to fresh material. Over an aging period of 4 months, a loss of approximately 15% of the total iodine capacity was seen. The iodine capacity loss on silver-functionalized aerogels due to NO2 was smaller than the iodine capacity loss due to humid or dry air aging.

  12. Simulation model air-to-air plate heat exchanger

    SciTech Connect (OSTI)

    Wetter, Michael

    1999-01-01T23:59:59.000Z

    A simple simulation model of an air-to-air plate heat exchanger is presented. The model belongs to a collection of simulation models that allows the eflcient computer simulation of heating, ventilation, and air-conditioning (HVAC) systems. The main emphasis of the models is to shorten computation time and to use only input data that are known in the design process of an HVAC system. The target of the models is to describe the behavior of HVAC components in the part-load operation mode, which is becoming increasingly important in energy eficient HVAC systems. The models are intended to be used for yearly energy calculations or load calculations with time steps of about 10 minutes or larger. Short- time dynamic effects, which are of interest for different aspects of control theory, are neglected. The part-load behavior is expressed in terms of the nominal condition and the dimensionless variation of the heat transfer with change of mass flow and temperature. The effectiveness- NTU relations are used to parametrize the convective heat transfer at nominal conditions and to compute the part-load condition. If the heat transfer coefficients on the two exchanger sides are not equal (i. e. due to partial bypassing of air), their ratio can be easily calculated and set as a parameter. The model is static and uses explicit equations only. The explicit model formulation ensures short computation time and numerical stability, which allows using the model with sophisticated engineering methods like automatic system optimization. This paper fully outlines the algorithm description and its simplifications. It is not tailored for any particular simulation program to ensure easy implementation in any simulation program.

  13. Life-cycle cost and payback period analysis for commercial unitary air conditioners

    E-Print Network [OSTI]

    Rosenquist, Greg; Coughlin, Katie; Dale, Larry; McMahon, James; Meyers, Steve

    2004-01-01T23:59:59.000Z

    Baseline Efficient Air Conditioners . . . . . . 28 AverageEfficient Air Conditioners . . . . . . . . . . . . . . . . .Btu/h Commercial Air Conditioners . . . . . . . . . . . . .

  14. Cell Senescence: Aging and Cancer

    ScienceCinema (OSTI)

    Campisi, Judith

    2013-05-29T23:59:59.000Z

    Scientists have identified a molecular cause behind the ravages of old age and in doing so have also shown how a natural process for fighting cancer in younger persons can actually promote cancer in older individuals.

  15. Neutron probe measurements of air saturation near an air sparging well

    SciTech Connect (OSTI)

    Acomb, L.J. [Geosphere, Inc., Anchorage, AK (United States); McKay, D.; Currier, P. [Army Corps of Engineers, Hanover, NH (United States). Cold Regions Research Engineering Lab.; Berglund, S.T.; Sherhart, T.V.; Benediktsson, C.V. [Federal Aviation Administration, Anchorage, AK (United States). Airway Facilities Div.

    1995-12-31T23:59:59.000Z

    In situ air sparging is being used to remediate diesel-fuel-contaminated soils in the zone of water table fluctuation at a remote Alaskan Federal Aviation Administration (FAA) air navigation aid site. A neutron probe was used to measure changes in percent air saturation during air sparging in a uniform, aeolian sand. Air was injected about 15 ft below the water table at air flowrates of 4 to 16 ft{sup 3}/min (cfm). The neutron probe data show that during air sparging the distribution of injected air changed through time, initially expanding outward from the sparge well screen, then consolidating around the air sparging well, until a steady-state condition was reached. The maximum radius of influence, measured at an air flowrate of 16 cfm, was about 15 ft during steady-state flow. At all air flowrates the percent air saturation was highest near the air sparging well and decreased radially away from the sparging well. Near the sparging well, the percent air saturation ranged from about 30% to >50% at air injection rates of 4 to 16 cfm. Where the percent air saturation is similar to that in the vadose zone, volatilization and biodegradation may occur at rates similar to those in the vadose zone. Selected air saturation results are presented, and dissolved oxygen and saturated zone pressure data are summarized.

  16. Model Refinement Needs A model developed by Peters and Marmorek (2003) will be used to generate predictions for

    E-Print Network [OSTI]

    449 Model Refinement Needs A model developed by Peters and Marmorek (2003) will be used to generate primarily an energy sink or primarily a source of food? More information is needed as to interactions predictions for comparison with observed variations in kokanee production. As with most models

  17. How smooth is the smoothest function in a given refinable space? Albert Cohen, Ingrid Daubechies, Amos Ron

    E-Print Network [OSTI]

    Ron, Amos

    of wavelets from multiresolution analysis, as well as in the study of subdivision algorithms is well are the univariate splines and the multivariate box splines (cf. [2]), and for these spline spaces the rigidHow smooth is the smoothest function in a given refinable space? Albert Cohen, Ingrid Daubechies

  18. How smooth is the smoothest function in a given refinable space? Albert Cohen, Ingrid Daubechies, Amos Ron

    E-Print Network [OSTI]

    Liblit, Ben

    analysis, as well as in the study of subdivision algorithms is well-known, well-understood and well of such spaces are the univariate splines and the multivariate box splines (cf. [2]), and for these spline spacesHow smooth is the smoothest function in a given refinable space? Albert Cohen, Ingrid Daubechies

  19. A posteriori error estimates with application of adaptive mesh refinement for thermal multiphase compositional flows in porous

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    of diffusive fluxes. Numerical results on an example of real-life thermal oil-recovery in a reservoir refinement, compositional Darcy flow, thermal flow, finite volume method 1 Introduction The thermal under a non-isothermal condition. The governing equations are the conservation of the amount of each

  20. Using Knowledge-Based Neural Networks to Improve Algorithms: Refining the Chou-Fasman Algorithm for Protein Folding

    E-Print Network [OSTI]

    Maclin, Rich

    for Protein Folding Richard Maclin Jude W. Shavlik Computer Sciences Dept. University of Wisconsin 1210 W learning Theory refinement Neural networks Finite-state automata Protein folding Chou-Fasman algorithm-Fasman algorithm, a method for predicting how globular proteins fold. Empirical evidence shows