Powered by Deep Web Technologies
Note: This page contains sample records for the topic "aerosol-based duct sealing" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


1

Aerosol-Based Duct Sealing Technology  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

8 8 Aerosol-Based Duct Sealing Technology During the past five years, research has quantified the impacts of residential duct system leakage on HVAC energy consumption and peak electricity demand. A typical house with ducts located in the attic or crawlspace wastes approximately 20% of heating and cooling energy through duct leaks and draws approximately 0.5 KW more electricity during peak cooling periods. A 1991 study indicated that sealing leaks could save close to one Quadrillion Btus per year. (see also Commercializing a New Technology) Because the major cost of sealing leaks in existing air distribution systems is the labor for the location and sealing process, reducing the labor could greatly improve the cost-effectiveness of such a retrofit. Field studies of duct sealing programs performed by HVAC contractors show

2

Laboratory and field testing of an aerosol-based duct-sealing technology  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Laboratory and field testing of an aerosol-based duct-sealing technology Laboratory and field testing of an aerosol-based duct-sealing technology for large commercial buildings. Title Laboratory and field testing of an aerosol-based duct-sealing technology for large commercial buildings. Publication Type Journal Article LBNL Report Number LBNL-44220 Year of Publication 2002 Authors Carrié, François Rémi, Ronnen M. Levinson, Tengfang T. Xu, Darryl J. Dickerhoff, William J. Fisk, Jennifer A. McWilliams, Mark P. Modera, and Duo Wang Journal ASHRAE Transactions Start Page Chapter Date Published January 2002 Abstract Laboratory and field experiments were performed to evaluate the feasibility of sealing leaks in commercial duct systems with an aerosol sealant. The method involves blowing an aerosol through the duct system to seal the leaks from the inside, the principle being that the aerosol particles deposit in the cracks as they try to escape under pressure. It was shown that the seals created with the current sealant material can withstand pressures far in excess of what is found in commercial-building duct systems. We also performed two field experiments in two large-commercial buildings. The ASHRAE leakage classes of the systems were reduced from 653 down to 103, and from 40 down to 3. Methods and devices specifically devised for this application proved to be very efficient at (a) increasing the sealing rate and (b) attaining state-of-the-art duct leakage classes. Additional research is needed to improve the aerosol injection and delivery processes.

3

Advanced Duct Sealing Testing  

SciTech Connect (OSTI)

Duct leakage has been identified as a major source of energy loss in residential buildings. Most duct leakage occurs at the connections to registers, plenums or branches in the duct system. At each of these connections a method of sealing the duct system is required. Typical sealing methods include tapes or mastics applied around the joints in the system. Field examinations of duct systems have typically shown that these seals tend to fail over extended periods of time. The Lawrence Berkeley National Laboratory has been testing sealant durability for several years. Typical duct tape (i.e. fabric backed tapes with natural rubber adhesives) was found to fail more rapidly than all other duct sealants. This report summarizes the results of duct sealant durability testing of five UL 181B-FX listed duct tapes (three cloth tapes, a foil tape and an Oriented Polypropylene (OPP) tape). One of the cloth tapes was specifically developed in collaboration with a tape manufacturer to perform better in our durability testing. The first test involved the aging of common ''core-to-collar joints'' of flexible duct to sheet metal collars, and sheet metal ''collar-to-plenum joints'' pressurized with 200 F (93 C) air. The second test consisted of baking duct tape specimens in a constant 212 F (100 C) oven following the UL 181B-FX ''Temperature Test'' requirements. Additional tests were also performed on only two tapes using sheet metal collar-to-plenum joints. Since an unsealed flexible duct joint can have a variable leakage depending on the positioning of the flexible duct core, the durability of the flexible duct joints could not be based on the 10% of unsealed leakage criteria. Nevertheless, the leakage of the sealed specimens prior to testing could be considered as a basis for a failure criteria. Visual inspection was also documented throughout the tests. The flexible duct core-to-collar joints were inspected monthly, while the sheet metal collar-to-plenum joints were inspected weekly. The baking test specimens were visually inspected weekly, and the durability was judged by the observed deterioration in terms of brittleness, cracking, flaking and blistering (the terminology used in the UL 181B-FX test procedure).

Sherman, Max H.; Walker, Iain S.

2003-08-01T23:59:59.000Z

4

Sealing ducts to save energy  

SciTech Connect (OSTI)

Large amounts of energy are wasted when heat leaks through ductwork located in uninsulated spaces. The Electric Power Research INstitute recently did a study that accurately measured these losses, then substantially reduced them by sealing the leaky ductwork. Six homes in the Pacific Northwest with significant duct leakage to the outside were selected for the study. The homes had electric resistance or heat pump, forced-air heating systems with a major portion of the supply and return ductwork in crawl spaces, attics, garages, etc. Measurements of duct leakage and heating system efficiency were done on all the homes before starting the duct sealing. Retrofitting included finding holes, gaps, cracks and disconnected joints in supply and return ducts as well as in plenums. When necessary, plenums were cut open for repairs. Leaks were sealed with Latex mastic and fiberglass tape. Outside ducts were covered or wrapped with insulation. Unducted returns were sealed with duct board. In some cases, leakage was corrected by merely reconnecting ducts and boots.

Siuru, B.

1996-07-01T23:59:59.000Z

5

Measure Guideline: Sealing and Insulating of Ducts in Existing Homes  

SciTech Connect (OSTI)

This document begins with a discussion on potential cost and performance benefits of duct sealing and insulating. It continues with a review of typical duct materials and components and the overall procedures for assessing and improving the duct system.

Aldrich, R.; Puttagunta, S.

2011-12-01T23:59:59.000Z

6

Ducts Sealing Using Injected Spray Sealant, Raleigh, North Carolina...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

sealed by hand with mastic. Air handlers were sealed with foil tape or mastic. Duct boots were sealed to floors and ceilings with foil tape or mastic. Lessons Learned *...

7

List of Duct/Air sealing Incentives | Open Energy Information  

Open Energy Info (EERE)

Duct/Air sealing Incentives Duct/Air sealing Incentives Jump to: navigation, search The following contains the list of 580 Duct/Air sealing Incentives. CSV (rows 1-500) CSV (rows 501-580) Incentive Incentive Type Place Applicable Sector Eligible Technologies Active AEP (Central and North) - Residential Energy Efficiency Programs (Texas) Utility Rebate Program Texas Construction Installer/Contractor Multi-Family Residential Building Insulation Caulking/Weather-stripping Comprehensive Measures/Whole Building Custom/Others pending approval Duct/Air sealing Unspecified technologies Yes AEP (Central and SWEPCO) - Coolsaver A/C Tune Up (Texas) Utility Rebate Program Texas Commercial Installer/Contractor Residential Central Air conditioners Custom/Others pending approval Duct/Air sealing

8

Flexible metallic seal for transition duct in turbine system  

SciTech Connect (OSTI)

A turbine system is disclosed. In one embodiment, the turbine system includes a transition duct. The transition duct includes an inlet, an outlet, and a passage extending between the inlet and the outlet and defining a longitudinal axis, a radial axis, and a tangential axis. The outlet of the transition duct is offset from the inlet along the longitudinal axis and the tangential axis. The transition duct further includes an interface member for interfacing with a turbine section. The turbine system further includes a flexible metallic seal contacting the interface member to provide a seal between the interface member and the turbine section.

Flanagan, James Scott; LeBegue, Jeffrey Scott; McMahan, Kevin Weston; Dillard, Daniel Jackson; Pentecost, Ronnie Ray

2014-04-22T23:59:59.000Z

9

Sealing Ducts in Large Commercial Buildings with Aerosolized Sealant Particles  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

2414 2414 1 Sealing Ducts in Large Commercial Buildings with Aerosolized Sealant Particles M. P. Modera, O. Brzozowski ** , F. R. Carrié * , D. J. Dickerhoff, W. W. Delp, W. J. Fisk, R. Levinson, D. Wang Abstract Electricity energy savings potential by eliminating air leakage from ducts in large commercial buildings is on the order of 10 kWh/m 2 per year (1 kWh/ft 2 ). We have tested, in two large commercial buildings, a new technology that simultaneously seals duct leaks and measures effective leakage area of ducts. The technology is based upon injecting a fog of aerosolized sealant particles into a pressurized duct system. In brief, this process involves blocking all of the intentional openings in a duct system (e.g., diffusers). Therefore, when the system is pressurized, the only place for the air carrying the aerosol

10

Sealing Ducts in Large Commercial Buildings with Aerosolized Sealant  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Sealing Ducts in Large Commercial Buildings with Aerosolized Sealant Sealing Ducts in Large Commercial Buildings with Aerosolized Sealant Particles Title Sealing Ducts in Large Commercial Buildings with Aerosolized Sealant Particles Publication Type Journal Article LBNL Report Number LBNL-42414 Year of Publication 2001 Authors Modera, Mark P., Olivier Brzozowski, François Rémi Carrié, Darryl J. Dickerhoff, William W. Delp, William J. Fisk, Ronnen M. Levinson, and Duo Wang Journal Energy & Buildings Volume 34 Start Page Chapter Pagination 705-714 Abstract Electricity energy savings potential by eliminating air leakage from ducts in large commercial buildings is on the order of 10 kWh/m2 per year (1 kWh/ft2). We have tested, in two large commercial buildings, a new technology that simultaneously seals duct leaks and measures effective leakage area of ducts. The technology is based upon injecting a fog of aerosolized sealant particles into a pressurized duct system. In brief, this process involves blocking all of the intentional openings in a duct system (e.g., diffusers). Therefore, when the system is pressurized, the only place for the air carrying the aerosol particles to exit the system is through the leaks. The key to the technology is to keep the particles suspended within the airstream until they reach the leaks, and then to have them leave the airstream and deposit on the leak sites. The principal finding from this field study was that the aerosol technology is capable of sealing the leaks in a large commercial building duct system within a reasonable time frame. In the first building, 66% of the leakage area was sealed within 2.5 hours of injection, and in the second building 86% of the leakage area was sealed within 5 hours. We also found that the aerosol could be blown through the VAV boxes in the second building without impacting their calibrations or performance. Some remaining questions are (1) how to achieve sealing rates comparable to those experienced in smaller residential systems; and (2) what tightness level these ducts systems can be brought to by means of aerosol sealing.

11

TOPIC Brief BUILDING TECHNOLOGIES PROGRAM Residential Duct Insulation and Sealing Requirements TOPIC BRIEF 1  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Duct Insulation and Sealing Requirements TOPIC BRIEF 1 Duct Insulation and Sealing Requirements TOPIC BRIEF 1 Residential Duct Insulation and Sealing Requirements Studies show that duct air leakage results in major energy losses. A ll versions of the International Energy Conservation Code (IECC) require ducts, air handlers, filter boxes, and air cavities used as ducts to be sealed, and reference Chapter 16 of the International Residential Code for details on air sealing. This sealing is required on all ducts and other air distribution components regardless of whether they are located inside or outside the conditioned living space. For single-family homes and other low-rise residential buildings, the 2009 and 2012 IECC have duct insulation and sealing requirements in Section 403.2. Both codes require insulation

12

Method and apparatus for duct sealing using a clog-resistant insertable injector  

DOE Patents [OSTI]

A method for forming a duct access region through one side of a previously installed air duct, wherein the air duct has an air flow with an air flow direction by inserting an aerosol injector into a previously installed air duct through the access region. The aerosol injector includes a liquid tube having a liquid tube orifice for ejecting a liquid to be atomized; and a propellant cap. The method is accomplished by aligning the aerosol injector with the direction of air flow in the duct; activating an air flow within the duct; and spraying a sealant through the aerosol injector to seal the duct in the direction of the air flow.

Wang, Duo (Albany, CA); Modera, Mark P. (Piedmont, CA)

2010-12-14T23:59:59.000Z

13

CASE STUDY OF DUCT RETROFIT OF A 1985 HOME AND GUIDELINES FOR ATTIC AND CRAWL SPACE DUCT SEALING  

SciTech Connect (OSTI)

The U.S. Department of Energy (DOE) is fully committed to research for developing the information and capabilities necessary to provide cost-effective residential retrofits yielding 50% energy savings within the next several years. Heating, ventilation, and air conditioning (HVAC) is the biggest energy end use in the residential sector, and a significant amount of energy can be wasted through leaky ductwork in unconditioned spaces such as attics and crawl spaces. A detailed duct sealing case study is presented for one house along with nine brief descriptions of other duct retrofits completed in the mixed-humid climate. Costs and estimated energy savings are reported for most of the ten houses. Costs for the retrofits ranged from $0.92/ft2 to $1.80/ft2 of living space and estimated yearly energy cost savings due to the duct retrofits range from 1.8% to 18.5%. Lessons learned and duct sealing guidelines based on these ten houses, as well as close work with the HVAC industry in the mixed-humid climate of East Tennessee, northern Georgia, and south-central Kentucky are presented. It is hoped that the lessons learned and guidelines will influence local HVAC contractors, energy auditors, and homeowners when diagnosing or repairing HVAC duct leakage and will be useful for steering DOE s future research in this area.

Boudreaux, Philip R [ORNL; Christian, Jeffrey E [ORNL; Jackson, Roderick K [ORNL

2012-01-01T23:59:59.000Z

14

Ducts Sealing Using Injected Spray Sealant, Raleigh, North Carolina (Fact Sheet)  

SciTech Connect (OSTI)

In multifamily and attached buildings, traditional duct sealing methods are often impractical or costly and disruptive because of the difficulty in accessing leakage sites. In this project, two retrofit duct sealing techniques - manually-applied sealants and injecting a spray sealant, were implemented in several low-rise multi-unit buildings. An analysis on the cost and performance of the two methods are presented. Each method was used in twenty housing units: approximately half of each group of units are single story and the remainder two-story. Results show that duct leakage to the outside was reduced by an average of 59% through the use of manual methods, and by 90% in the units where the injected spray sealant was used. It was found that 73% of the leakage reduction in homes that were treated with injected spray sealant was attributable to the manual sealing done at boots, returns and the air handler. The cost of manually-applying sealant ranged from $275 to $511 per unit and for the injected spray sealant the cost was $700 per unit. Modeling suggests a simple payback of 2.2 years for manual sealing and 4.7 years for the injected spray sealant system. Utility bills were collected for one year before and after the retrofits. Utility bill analysis shows 14% and 16% energy savings using injected spray sealant system and hand sealing procedure respectively in heating season whereas in cooling season, energy savings using injected spray sealant system and hand sealing were both 16%.

Not Available

2014-03-01T23:59:59.000Z

15

Field Test of Advanced Duct-Sealing Technologies Within the Weatherization Assistance Program  

SciTech Connect (OSTI)

A field test of an aerosol-spray duct-sealing technology and a conventional, best-practice approach was performed in 80 homes to determine the efficacy and programmatic needs of the duct-sealing technologies as applied in the U.S. Department of Energy Weatherization Assistance Program. The field test was performed in five states: Iowa, Virginia, Washington, West Virginia, and Wyoming. The study found that, compared with the best-practice approach, the aerosol-spray technology is 50% more effective at sealing duct leaks and can potentially reduce labor time and costs for duct sealing by 70%, or almost 4 crew-hours. Further study to encourage and promote use of the aerosol-spray technology within the Weatherization Assistance Program is recommended. A pilot test of full production weatherization programs using the aerosol-spray technology is recommended to develop approaches for integrating this technology with other energy conservation measures and minimizing impacts on weatherization agency logistics. In order to allow or improve adoption of the aerosol spray technology within the Weatherization Assistance Program, issues must be addressed concerning equipment costs, use of the technology under franchise arrangements with Aeroseal, Inc. (the holders of an exclusive license to use this technology), software used to control the equipment, safety, and training. Application testing of the aerosol-spray technology in mobile homes is also recommended.

Ternes, MP

2001-12-05T23:59:59.000Z

16

Duct System Flammability and Air Sealing Fire Separation Assemblies in the International Residential Code  

SciTech Connect (OSTI)

IBACOS identified two barriers that limit the ability of builders to cost-effectively achieve higher energy efficiency levels in housing. These are (1) the use of duct system materials that inherently achieve airtightness and are appropriately sized for low-load houses and (2) the ability to air seal fire separation assemblies. The issues identified fall into a gray area of the codes.

Rudd, A.; Prahl, D.

2014-12-01T23:59:59.000Z

17

Building America Technology Solutions for New and Existing Homes: Duct Sealing Using Injected Spray Sealant  

Broader source: Energy.gov [DOE]

In this project, the Raleigh Housing Authority worked with Building America team, the Advanced Residential Integrated Solutions Collaborative to determine the most cost-effective ways to reduce duct leakage in its low-rise housing units.

18

Duct joining system  

SciTech Connect (OSTI)

A duct joining system for providing an air-tight seal and mechanical connection for ducts and fittings is disclosed. The duct joining system includes a flexible gasket affixed to a male end of a duct or fitting. The flexible gasket is affixed at an angle relative to normal of the male end of the duct. The female end of the other duct includes a raised bead in which the flexible gasket is seated when the ducts are properly joined. The angled flexible gasket seated in the raised bead forms an air-tight seal as well as fastens or locks the male end to the female end. Alternatively, when a flexible duct is used, a band clamp with a raised bead is clamped over the female end of the flexible duct and over the male end of a fitting to provide an air tight seal and fastened connection.

Proctor, John P. (44 Glen Dr., Fairfax, CA 94930); deKieffer, Robert C. (Boulder, CO)

2001-01-01T23:59:59.000Z

19

Duct Joining System  

DOE Patents [OSTI]

A duct joining system for providing an air-tight seal and mechanical connection for ducts and fittings is disclosed. The duct joining system includes a flexible gasket affixed to a male end of a duct or fitting. The flexible gasket is affixed at an angle relative to normal of the male end of the duct. The female end of the other duct includes a raised bead in which the flexible gasket is seated when the ducts are properly joined. The angled flexible gasket seated in the raised bead forms an air-tight seal as well as fastens or locks the male end to the female end. Alternatively, when a flexible duct is used, a band clamp with a raised bead is clamped over the female end of the flexible duct and over the male end of a fitting to provide an air tight seal and fastened connection.

Proctor, John P. (Fairfax, CA)

2001-02-27T23:59:59.000Z

20

STATE OF CALIFORNIA DUCT LEAKAGE TEST EXISTING DUCT SYSTEM  

E-Print Network [OSTI]

.g., register boots, air handler, coil, plenums, etc.) if those parts are accessible and they can be sealed 2010 Outside air (OA) ducts for Central Fan Integrated (CFI) ventilation systems, shall not be sealed. Option 3. Reduce leakage by 60% or more, and conduct smoke test to seal all accessible leaks. Option 4

Note: This page contains sample records for the topic "aerosol-based duct sealing" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


21

T-method duct design. Part 4: Duct leakage theory  

SciTech Connect (OSTI)

Studies have shown that duct leakage depends on the method of duct fabrication, method of sealing, workmanship, and static pressure differential. An equation that describes leakage as a function of leakage class and static pressure is presented in the Duct Design chapter of the 1993 ASHRAE Handbook. This equation is used to calculate the leakage rate through a unit of duct surface for constant duct static pressure. However, the static pressure of a leaking duct does not remain constant. This process is described by a differential equation. The magnitude of duct leakage for a straight duct depends on internal static pressure and varies uniformly along its length (assumption). Fittings in a system cause sudden changes in static pressure; therefore, duct leakage depends on fitting locations. There are two approaches for duct system leakage calculation: (1) Accurate -- For accurate duct leakage calculations, the duct system is divided into single sections between fittings and the leakage rate and pressure loss for each section calculated by the weighing factor method. (2) Approximate -- For most applications, duct leakage can be calculated by approximate formulas based on the average static pressure in a duct section. Leakage calculation requires dividing the system into sections between each fitting. This paper, the fourth in a series on T-method duct design, discusses the theory of calculating air leakage from/into a single duct to incorporate duct leakage into the optimization and simulation calculation procedures.

Tsal, R.J.; Varvak, L.P. [NETSAL and Associates, Fountain Valley, CA (United States); Behls, H.F. [Behls and Associates, Arlington Heights, IL (United States)

1998-12-31T23:59:59.000Z

22

Achieving Airtight Ducts in Manufactured Housing  

E-Print Network [OSTI]

correlated with achieving CFM25OUT=3% in mastic sealed systems, but less reliably with taped systems. Cost for achieving duct tightness goals range from $4 to $8 including duct testing on the assembly line...

McIlvaine, J.; Beal, D.; Moyer, N.; Chasar, D.; Chandra, S.

2004-01-01T23:59:59.000Z

23

Duct Tape Durability Testing  

SciTech Connect (OSTI)

Duct leakage is a major source of energy loss in residential buildings. Most duct leakage occurs at the connections to registers, plenums, or branches in the duct system. At each of these connections, a method of sealing the duct system is required. Typical sealing methods include tapes or mastics applied around the joints in the system. Field examinations of duct systems have shown that taped seals tend to fail over extended periods of time. The Lawrence Berkeley National Laboratory (LBNL) has been testing sealant durability for several years using accelerated test methods and found that typical duct tape (i.e., cloth-backed tapes with natural rubber adhesives) fails more rapidly than other duct sealants. This report summarizes the results of duct sealant durability testing over two years for four UL 181B-FX listed duct tapes (two cloth tapes, a foil tape and an Oriented Polypropylene (OPP) tape). One of the cloth tapes was specifically developed in collaboration with a tape manufacturer to perform better in our durability testing. The tests involved the aging of common ''core-to-collar joints'' of flexible duct to sheet metal collars. Periodic air leakage tests and visual inspection were used to document changes in sealant performance. After two years of testing, the flex-to-collar connections showed little change in air leakage, but substantial visual degradation from some products. A surprising experimental result was failure of most of the clamps used to mechanically fasten the connections. This indicates that the durability of clamps also need to be addressed ensure longevity of the duct connection. An accelerated test method developed during this study has been used as the basis for an ASTM standard (E2342-03).

Sherman, Max H.; Walker, Iain S.

2004-04-01T23:59:59.000Z

24

Tips: Air Ducts | Department of Energy  

Broader source: Energy.gov (indexed) [DOE]

Air Ducts Air Ducts Tips: Air Ducts June 24, 2013 - 7:23pm Addthis Air Ducts: Out of Sight, Out of Mind. The unsealed ducts in your attic and crawlspaces lose air, and uninsulated ducts lose heat -- wasting energy and money. Air Ducts: Out of Sight, Out of Mind. The unsealed ducts in your attic and crawlspaces lose air, and uninsulated ducts lose heat -- wasting energy and money. Your air ducts are one of the most important systems in your home, and if the ducts are poorly sealed or insulated they are likely contributing to higher energy bills. Your home's duct system is a branching network of tubes in the walls, floors, and ceilings; it carries the air from your home's furnace and central air conditioner to each room. Ducts are made of sheet metal, fiberglass, or other materials.

25

E-Print Network 3.0 - air duct work Sample Search Results  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Duct Sealants Published in Proc. RILEM 3rd Summary: residential buildings 1. The air distribution systems require some sort of seal between duct sections... -40% of the...

26

Evaluation of PEGIT duct connection system  

SciTech Connect (OSTI)

Most air duct system components are assembled in the field and are mechanically fastened by sheet metal screws (for sheet metal-to-sheet metal) or by drawbands (for flex duct-to-sheet metal). Air sealing is separate from this mechanical fastening and is usually achieved using tape or mastic products after mechanical fastening. Field observations have shown that mechanical fastening rarely meets code or manufacturers requirements and that sealing procedures are similarly inconsistent. To address these problems, Proctor Engineering Group (PEG) is developing a system of joining ducts (called PEGIT) that combines the mechanical fastening and sealing into a single self-contained procedure. The PEGIT system uses a shaped flexible seal between specially designed sheet metal duct fittings to both seal and fasten duct sections together. Figure 1 shows the inner duct fitting complete with rubber seal. This seal provides the air seal for the completed fitting and is shaped to allow the inner and outer fittings to slide together, and then to lock the fittings in place. The illustration in Figure 2 shows the approximate cross section of the rubber seal that shows how the seal has a lip that is angled backwards. This angled lip allows the joint to be pushed together by folding flat but then its long axis makes it stiff in the pulling apart direction. This study was undertaken to assist PEG in some of the design aspects of this system and to test the performance of the PEGIT system. This study was carried out in three phases. The initial phase evaluated the performance of a preliminary seal design for the PEGIT system. After the first phase, the seal was redesigned and this new seal was evaluated in the second phase of testing. The third phase performed more detailed testing of the second seal design to optimize the production tolerances of the sheet metal fittings. This report summarizes our findings from the first two phases and provides details about the third phase of testing.

Walker, Iain S.; Brenner, Douglas E.; Sherman, Max H.; Dickerhoff, Darryl J.

2003-08-01T23:59:59.000Z

27

Assessing the Longevity of Residential Duct Sealants Published in Proc. RILEM 3rd  

E-Print Network [OSTI]

residential buildings [1]. The air distribution systems require some sort of seal between duct sections significant leakage to outside because these spaces are not air sealed. Residential duct systems in the U not usually provide an air seal. High pressure drops in the vicinity of the air handler and associated plenum

28

Q. For the 2005 Standards there is a new compliance credit for "ducts buried in attic insulation." What must be done to qualify for that credit?  

E-Print Network [OSTI]

Q. For the 2005 Standards there is a new compliance credit for "ducts buried in attic insulation installation of insulation and duct sealing. When taking the buried duct credit, a minimum of R-30 insulation-4.2 duct insulation. Only the portions of duct runs that are directly on or within 3.5 inches

29

Minimizing Energy Losses in Ducts | Department of Energy  

Broader source: Energy.gov (indexed) [DOE]

Minimizing Energy Losses in Ducts Minimizing Energy Losses in Ducts Minimizing Energy Losses in Ducts June 24, 2012 - 5:45pm Addthis Placing ductwork in conditioned space can help reduce energy losses. | Photo courtesy of ©iStockphoto/SimplyCreativePhotography Placing ductwork in conditioned space can help reduce energy losses. | Photo courtesy of ©iStockphoto/SimplyCreativePhotography In new home construction or in retrofits, proper duct system design is critical. In recent years, energy-saving designs have sought to include ducts and heating systems in the conditioned space. Many existing duct systems lose a lot of energy from leakage and poor insulation, but you can reduce that loss by sealing and insulating your ducts. Existing ducts may also be blocked or may require simple upgrades.

30

Security seal  

DOE Patents [OSTI]

Security for a package or verifying seal in plastic material is provided by a print seal with unique thermally produced imprints in the plastic. If tampering is attempted, the material is irreparably damaged and thus detectable. The pattern of the imprints, similar to "fingerprints" are recorded as a positive identification for the seal, and corresponding recordings made to allow comparison. The integrity of the seal is proved by the comparison of imprint identification records made by laser beam projection.

Gobeli, Garth W. (Albuquerque, NM)

1985-01-01T23:59:59.000Z

31

Conformable seal  

DOE Patents [OSTI]

Sealing apparatus and method, comprising first and second surfaces or membranes, at least one of which surfaces is deformable, placed in proximity to one another. Urging means cause these surfaces to contact one another in a manner such that the deformable surface deforms to conform to the geometry of the other surface, thereby creating a seal. The seal is capable of undergoing multiple cycles of sealing and unsealing.

Neef, W.S.; Lambert, D.R.

1982-08-10T23:59:59.000Z

32

Measure Guideline: Summary of Interior Ducts in New Construction, Including an Efficient, Affordable Method to Install Fur-Down Interior Ducts  

SciTech Connect (OSTI)

This document illustrates guidelines for the efficient installation of interior duct systems in new housing, including the fur-up chase method, the fur-down chase method, and interior ducts positioned in sealed attics or sealed crawl spaces. This document illustrates guidelines for the efficient installation of interior duct systems in new housing. Interior ducts result from bringing the duct work inside a home's thermal and air barrier. Architects, designers, builders, and new home buyers should thoroughly investigate any opportunity for energy savings that is as easy to implement during construction, such as the opportunity to construct interior duct work. In addition to enhanced energy efficiency, interior ductwork results in other important advantages, such as improved indoor air quality, increased system durability and increased homeowner comfort. While the advantages of well-designed and constructed interior duct systems are recognized, the implementation of this approach has not gained a significant market acceptance. This guideline describes a variety of methods to create interior ducts including the fur-up chase method, the fur-down chase method, and interior ducts positioned in sealed attics or sealed crawl spaces. As communication of the intent of an interior duct system, and collaboration on its construction are paramount to success, this guideline details the critical design, planning, construction, inspection, and verification steps that must be taken. Involved in this process are individuals from the design team; sales/marketing team; and mechanical, insulation, plumbing, electrical, framing, drywall and solar contractors.

Beal, D.; McIlvaine , J.; Fonorow, K.; Martin, E.

2011-11-01T23:59:59.000Z

33

Encapsulated and Buried Ducts  

Broader source: Energy.gov (indexed) [DOE]

Encapsulated and Buried Ducts Robb Aldrich Steven Winter Associates, Inc. Why Buried Ducts?  Ductwork thermal losses can range from 10-45%  Interior ducts current solution, but may be impractical, expensive, or increase envelope loads Insulation & Air Barrier First Tests - Florida Early Buried Duct Tests (FL) Condensation? Master Bedroom Duct in Attic 10 15 20 25 30 35 40 45 50 55 Duct Top Temp Duct Side Temp Duct Bot. Temp Duct Side Dewpoint Duct Bot. Dewpoint Attic Temp 7/8/2000 7/8/2000 7/8/2000 7/8/2000 7/8/2000 7/8/2000 7/9/2000 0:00 4:00 8:00 12:00 16:00 20:00 0:00 Time California: Much drier, no Problem Implementation Getting it Right... in Florida A Solution for Humid Climates Encapsulated, then Buried Research Questions  What are the effective R-values?

34

Building America Webinar: Sealing of Home Enclosures with Aerosol Particles  

Broader source: Energy.gov [DOE]

This webinar was presented by research team Building Industry Research Alliance (BIRA), and provided information about a project that uses existing aerosol duct sealing technology to seal the entire building enclosure in order to achieve greater airtightness and energy and cost savings.

35

New and Underutilized Technology: Duct Sealants | Department of Energy  

Broader source: Energy.gov (indexed) [DOE]

Duct Sealants Duct Sealants New and Underutilized Technology: Duct Sealants October 8, 2013 - 3:01pm Addthis The following information outlines key deployment considerations for duct sealants within the Federal sector. Benefits Aerosol sealant is injected into the ductwork to seal leaks. This can save energy and costs associated with heating, cooling, and fan operation depending on building type. Application Condensing boilers are appropriate for most building applications. Key Factors for Deployment Sealing ductwork should be a standard energy conservation measure evaluated during design, construction, major renovation, or other HVAC projects. Ranking Criteria Federal energy savings, cost-effectiveness, and probability of success are ranked 0-5 with 0 representing the lowest ranking and 5 representing the

36

Hollow lensing duct  

DOE Patents [OSTI]

A hollow lensing duct to condense (intensify) light using a combination of focusing using a spherical or cylindrical lens followed by reflective waveguiding. The hollow duct tapers down from a wide input side to a narrow output side, with the input side consisting of a lens that may be coated with an antireflective coating for more efficient transmission into the duct. The inside surfaces of the hollow lens duct are appropriately coated to be reflective, preventing light from escaping by reflection as it travels along the duct (reflective waveguiding). The hollow duct has various applications for intensifying light, such as in the coupling of diode array pump light to solid state lasing materials.

Beach, Raymond J. (Livermore, CA); Honea, Eric C. (Sunol, CA); Bibeau, Camille (Dublin, CA); Mitchell, Scott (Tracy, CA); Lang, John (Pleasanton, CA); Maderas, Dennis (Pleasanton, CA); Speth, Joel (San Ramon, CA); Payne, Stephen A. (Castro Valley, CA)

2000-01-01T23:59:59.000Z

37

INTERIOR DUCT SYSTEM DESIGN, CONSTRUCTION, AND PERFORMANCE  

SciTech Connect (OSTI)

By removing air distribution and conditioning equipment from unconditioned spaces, homeowners stand to benefit substantially with respect to both energy savings and indoor air quality. Duct leakage introduces: Greater heating and cooling loads from air at extreme temperatures and humidity levels; Outside air and air from unconditioned spaces that may contain air borne contaminants, combustion gases, pollen, mold spores, and/or particles of building materials; and Higher whole-house infiltration/exfiltration rates. Exemplary studies conducted since 1990 have demonstrated the prevalence of duct leakage throughout the United States and measured energy savings of approximately 20% during both heating and cooling seasons from leakage reduction. These all dealt with duct leakage to and/or from unconditioned spaces. In the building science community, leakage within the conditioned space is generally presumed to eliminate the negative consequences of duct leakage with the exception of possibly creating pressure imbalances in the house which relates to higher infiltration and/or exfiltration. The practical challenges of isolating ducts and air handlers from unconditioned spaces require builders to construct an air-tight environment for the ducts. Florida Solar Energy Center researchers worked with four builders in Texas, North Carolina, and Florida who build a furred-down chase located either in a central hallway or at the edges of rooms as an architectural detail. Some comparison homes with duct systems in attics and crawl spaces were included in the test group of more than 20 homes. Test data reveals that all of the duct/AHU systems built inside the conditioned space had lower duct leakage to unconditioned spaces than their conventional counterparts; however, none of the homes was completely free of duct leakage to unconditioned spaces. Common problems included wiring and plumbing penetrations of the chase, failure to treat the chase as an air tight space, and misguided fresh air inlet design. Improvements were implemented by the Texas builder and retested in July. Results showed a 36% reduction in duct leakage, significant enough to warrant the builder adopting the new sealing procedure.

Janet E.R. Mcllvaine; David Beal; Philip Fairey

2001-10-10T23:59:59.000Z

38

Building America Case Study: Duct in Conditioned Space in a Dropped Ceiling or Fur-down, Gainesville, Florida (Fact Sheet)  

SciTech Connect (OSTI)

Forced air distribution systems (duct systems) typically are installed out of sight for aesthetic reasons, most often in unconditioned areas such as an attic or crawlspace. Any leakage of air to or from the duct system (duct leakage) in unconditioned space not only loses energy, but impacts home and equipment durability and indoor air quality. An obvious solution to this problem is to bring the duct system into the interior of the house, either by sealing the area where the ducts are installed (sealed attic or crawlspace) or by building an interior cavity or chase above the ceiling plane (raised ceiling or fur-up chase) or below the ceiling plane (dropped ceiling or fur-down) for the duct system. This case study examines one Building America builder partner's implementation of an inexpensive, quick and effective method of building a fur-down or dropped ceiling chase.

Not Available

2014-09-01T23:59:59.000Z

39

Longevity of Duct Tape in Residential Air Distribution Systems: 1-D, 2-D, and 3-D Joints  

E-Print Network [OSTI]

Group (EPB) at Lawrence Berkeley National Laboratory (Abushakra 2002). This study is a continuation of previous studies conducted at LBNL (Walker et al. 1998 and 1999, Walker and Sherman 2000, and Sherman et al. 2000), whose objectives... flexible duct core-to-collar joints. ADC does not provide recommendations for the collar-to-plenum joints. Previous duct sealing tests conducted at LBNL covered two types of joints, core-to-collar, and collar- to-plenum, using sheet metal ducts...

Abushakra, B.

2003-01-01T23:59:59.000Z

40

Regenerator seal  

DOE Patents [OSTI]

A method for manufacturing a hot side regenerator cross arm seal assembly having a thermally stablilized wear coating with a substantially flat wear surface thereon to seal between low pressure and high pressure passages to and from the hot inboard side of a rotary regenerator matrix includes the steps of forming a flat cross arm substrate member of high nickel alloy steel; fixedly securing the side edges of the substrate member to a holding fixture with a concave surface thereacross to maintain the substrate member to a slightly bent configuration on the fixture surface between the opposite ends of the substrate member to produce prestress therein; applying coating layers on the substrate member including a wear coating of plasma sprayed nickel oxide/calcium flouride material to define a wear surface of slightly concave form across the restrained substrate member between the free ends thereon; and thereafter subjecting the substrate member and the coating thereon to a heat treatment of 1600.degree. F. for sixteen hours to produce heat stabilizing growth in the coating layers on the substrate member and to produce a thermally induced growth stress in the wear surface that substantially equalizes the prestress in the substrate whereby when the cross arm is removed from the fixture surface following the heat treatment step a wear face is formed on the cross arm assembly that will be substantially flat between the ends.

Davis, Leonard C. (Indianapolis, IN); Pacala, Theodore (Indianapolis, IN); Sippel, George R. (Indianapolis, IN)

1981-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "aerosol-based duct sealing" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


41

Measure Guideline: Buried and/or Encapsulated Ducts  

SciTech Connect (OSTI)

Buried and/or encapsulated ducts (BEDs) are a class of advanced, energy-efficiency strategies intended to address the significant ductwork thermal losses associated with ducts installed in unconditioned attics. BEDs are ducts installed in unconditioned attics that are covered in loose-fill insulation and/or encapsulated in closed cell polyurethane spray foam insulation. This Measure Guideline covers the technical aspects of BEDs as well as the advantages, disadvantages, and risks of BEDs compared to other alternative strategies. This guideline also provides detailed guidance on installation of BEDs strategies in new and existing homes through step-by-step installation procedures. This Building America Measure Guideline synthesizes previously published research on BEDs and provides practical information to builders, contractors, homeowners, policy analysts, building professions, and building scientists. Some of the procedures presented here, however, require specialized equipment or expertise. In addition, some alterations to duct systems may require a specialized license. Persons implementing duct system improvements should not go beyond their expertise or qualifications. This guideline provides valuable information for a building industry that has struggled to address ductwork thermal losses in new and existing homes. As building codes strengthen requirements for duct air sealing and insulation, flexibility is needed to address energy efficiency goals. While ductwork in conditioned spaces has been promoted as the panacea for addressing ductwork thermal losses, BEDs installations approach - and sometimes exceed - the performance of ductwork in conditioned spaces.

Shapiro, C.; Zoeller, W.; Mantha, P.

2013-08-01T23:59:59.000Z

42

Integrating ducts into the conditioned space: Successes and challenges  

SciTech Connect (OSTI)

In residential and light commercial construction in the United States, heating and cooling ducts are often located outside the thermal or pressure boundary of the conditioned space. This location is selected for aesthetic and space requirement reasons. Typical duct locations include attics, above dropped ceilings, crawlspaces, and attached garages. A wide body of literature has found that distribution system conduction and air leakage can cause 30-40% energy losses before cooling and heating air reaches the conditioned space. Recent innovative attempts at locating ducts in the conditioned space have had mixed results in terms of improving duct efficiency. Some of these strategies include cathedralizing attics (sealing and insulating at the attic roofline) and locating ducts in interstitial spaces. This paper reviews modeling studies that suggest substantial savings could be realized from these strategies and presents field measurements which reveal that construction planning and execution errors can prevent these strategies from being widely applied or from being effective when they are applied. These types of problems will need to be overcome for effective integration of ducts into the conditioned space.

Siegel, Jeffrey; Walker, Iain

2004-05-01T23:59:59.000Z

43

Duct leakage impacts on VAV system performance in California large commercial buildings  

SciTech Connect (OSTI)

The purpose of this study is to evaluate the variability of duct leakage impacts on air distribution system performance for typical large commercial buildings in California. Specifically, a hybrid DOE-2/TRNSYS sequential simulation approach was used to model the energy use of a low-pressure terminal-reheat variable-air-volume (VAV) HVAC system with six duct leakage configurations (tight to leaky) in nine prototypical large office buildings (representing three construction eras in three California climates where these types of buildings are common). Combined fan power for the variable-speed-controlled supply and return fans at design conditions was assumed to be 0.8 W/cfm. Based on our analyses of the 54 simulation cases, the increase in annual fan energy is estimated to be 40 to 50% for a system with a total leakage of 19% at design conditions compared to a tight system with 5% leakage. Annual cooling plant energy also increases by about 7 to 10%, but reheat energy decreases (about 3 to 10%). In combination, the increase in total annual HVAC site energy is 2 to 14%. The total HVAC site energy use includes supply and return fan electricity consumption, chiller and cooling tower electricity consumption, boiler electricity consumption, and boiler natural gas consumption. Using year 2000 average commercial sector energy prices for California ($0.0986/kWh and $7.71/Million Btu), the energy increases result in 9 to 18% ($7,400 to $9,500) increases in HVAC system annual operating costs. Normalized by duct surface area, the increases in annual operating costs are 0.14 to 0.18 $/ft{sup 2}. Using a suggested one-time duct sealing cost of $0.20 per square foot of duct surface area, these results indicate that sealing leaky ducts in VAV systems has a simple payback period of about 1.3 years. Even with total leakage rates as low as 10%, duct sealing is still cost effective. This suggests that duct sealing should be considered at least for VAV systems with 10% or more total duct leakage. The VAV system that we simulated had perfectly insulated ducts, and maintained constant static pressure in the ducts upstream of the VAV boxes and a constant supply air temperature at the airhandler. Further evaluations of duct leakage impacts should be carried out in the future after methodologies are developed to deal with duct surface heat transfer effects, to deal with airflows entering VAV boxes from ceiling return plenums (e.g., to model parallel fan-powered VAV boxes), and to deal with static pressure reset and supply air temperature reset strategies.

Wray, Craig P.; Matson, Nance E.

2003-10-01T23:59:59.000Z

44

Chapter Three - Rotary Seals  

Science Journals Connector (OSTI)

This chapter discusses the range of rotary seals available that can be applied across a range of industries. The basic operation, key design features and the many potential variants of rotary-shaft lip seals are discussed, plus plastic seals that can be used to extend the performance envelope. Variants that may be used for exclusion of contaminant and alternative designs of elastomer and plastic seals, some of which can be used at high pressures in specialized applications, are covered. The basic design and operation of mechanical seals are discussed. The differences in seal designs covering the range from domestic goods and automotive through process plant to turbo machinery are covered. The key features of compression packing and modern material options are presented. A wide range of other seal types are also used in rotating machinery, particularly in high-speed turbo machinery. Current developments for a number of seal types, labyrinth, honeycomb, leaf seals, brush seals and viscoseals, are summarized.

Robert Flitney

2014-01-01T23:59:59.000Z

45

Mechanical seal assembly  

DOE Patents [OSTI]

An improved mechanical seal assembly is provided for sealing rotating shafts with respect to their shaft housings, wherein the rotating shafts are subject to substantial axial vibrations. The mechanical seal assembly generally includes a rotating sealing ring fixed to the shaft, a non-rotating sealing ring adjacent to and in close contact with the rotating sealing ring for forming an annular seal about the shaft, and a mechanical diode element that applies a biasing force to the non-rotating sealing ring by means of hemispherical joint. The alignment of the mechanical diode with respect to the sealing rings is maintained by a series of linear bearings positioned axially along a desired length of the mechanical diode. Alternative embodiments include mechanical or hydraulic amplification components for amplifying axial displacement of the non-rotating sealing ring and transferring it to the mechanical diode.

Kotlyar, Oleg M. (Salt Lake City, UT)

2001-01-01T23:59:59.000Z

46

Mechanical seal assembly  

DOE Patents [OSTI]

An improved mechanical seal assembly is provided for sealing rotating shafts with respect to their shaft housings, wherein the rotating shafts are subject to substantial axial vibrations. The mechanical seal assembly generally includes a rotating sealing ring fixed to the shaft, a non-rotating sealing ring adjacent to and in close contact with the rotating sealing ring for forming an annular seal about the shaft, and a mechanical diode element that applies a biasing force to the non-rotating sealing ring by means of hemispherical joint. The alignment of the mechanical diode with respect to the sealing rings is maintained by a series of linear bearings positioned axially along a desired length of the mechanical diode. Alternative embodiments include mechanical or hydraulic amplification components for amplifying axial displacement of the non-rotating sealing ring and transfering it to the mechanical diode.

Kotlyar, Oleg M. (Salt Lake City, UT)

2002-01-01T23:59:59.000Z

47

Rotary shaft sealing assembly  

DOE Patents [OSTI]

A rotary shaft sealing assembly in which a first fluid is partitioned from a second fluid in a housing assembly having a rotary shaft located at least partially within. In one embodiment a lip seal is lubricated and flushed with a pressure-generating seal ring preferably having an angled diverting feature. The pressure-generating seal ring and a hydrodynamic seal may be used to define a lubricant-filled region with each of the seals having hydrodynamic inlets facing the lubricant-filled region. Another aspect of the sealing assembly is having a seal to contain pressurized lubricant while withstanding high rotary speeds. Another rotary shaft sealing assembly embodiment includes a lubricant supply providing a lubricant at an elevated pressure to a region between a lip seal and a hydrodynamic seal with a flow control regulating the flow of lubricant past the lip seal. The hydrodynamic seal may include an energizer element having a modulus of elasticity greater than the modulus of elasticity of a sealing lip of the hydrodynamic seal.

Dietle, Lannie L; Schroeder, John E; Kalsi, Manmohan S; Alvarez, Patricio D

2013-08-13T23:59:59.000Z

48

Development of Dual-Air-Assistant Atomizing Nozzle to Apply Aerosol-Sealing  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Development of Dual-Air-Assistant Atomizing Nozzle to Apply Aerosol-Sealing Development of Dual-Air-Assistant Atomizing Nozzle to Apply Aerosol-Sealing Technology in Air Duct Systems Speaker(s): Alan Ropers Date: July 8, 2002 - 12:00pm Location: Bldg. 90 An Aerosol-sealing Technology was developed by LBNL to seal leaks in Air Duct Systems (ADS). The firm AEROSEAL already commercializes this technology for residential ADS. The current goal of our research at the Laboratory is to apply this technology to large commercial ADS. That means to develop a new kind of injector called "Compact Injector". So far, the injector that is used is a nozzle from the Schlick-Dusen firm. Results in terms of sealing rate are satisfactory, but this nozzle quickly clogs up with sealant particles. There are two reasons for the clogging problem: the

49

Titanium sealing glasses and seals formed therefrom  

DOE Patents [OSTI]

Alkaline-earth lanthanoborate sealing-glass compositions containing CaO, La{sub 2}O{sub 3}, B{sub 2}O{sub 3}, TiO{sub 2} and Al{sub 2}O{sub 3} in various combinations of mole-% are provided. These sealing-glass compositions are useful for forming hermetic glass-to-metal seals with titanium and titanium alloys that have a high aqueous durability for component or device applications requiring exposure to moisture, water or body fluids. Particular applications of the titanium sealing-glass compositions include forming glass-to-metal seals for lithium batteries and implanted biomedical devices (e.g. batteries, pacemakers, defibrillators, pumps). 2 figs.

Brow, R.K.; McCollister, H.L.; Phifer, C.C.; Day, D.E.

1997-12-02T23:59:59.000Z

50

Titanium sealing glasses and seals formed therefrom  

DOE Patents [OSTI]

Alkaline-earth lanthanoborate sealing-glass compositions containing CaO, La.sub.2 O.sub.3, B.sub.2 O.sub.3, TiO.sub.2 and Al.sub.2 O.sub.3 in various combinations of mole-% are provided. These sealing-glass compositions are useful for forming hermetic glass-to-metal seals with titanium and titanium alloys that have a high aqueous durability for component or device applications requiring exposure to moisture, water or body fluids. Particular applications of the titanium sealing-glass compositions include forming glass-to-metal seals for lithium batteries and implanted biomedical devices (e.g. batteries, pacemakers, defibrillators, pumps).

Brow, Richard K. (Albuquerque, NM); McCollister, Howard L. (Albuquerque, NM); Phifer, Carol C. (Albuquerque, NM); Day, Delbert E. (Rolla, MO)

1997-01-01T23:59:59.000Z

51

Collapsable seal member  

DOE Patents [OSTI]

A hollow, collapsable seal member normally disposed in a natural expanded state offering fail-safe pressure sealing against a seating surface and adapted to be evacuated by a vacuum force for collapsing the seal member to disengage the same from said seating surface.

Sherrell, Dennis L. (Kennewick, WA)

1990-01-01T23:59:59.000Z

52

Low Cost, Durable Seal  

SciTech Connect (OSTI)

Seal durability is critical to achieving the 2010 DOE operational life goals for both stationary and transportation PEM fuel cell stacks. The seal material must be chemically and mechanically stable in an environment consisting of aggressive operating temperatures, humidified gases, and acidic membranes. The seal must also be producible at low cost. Currentlyused seal materials do not meet all these requirements. This project developed and demonstrated a high consistency hydrocarbon rubber seal material that was able to meet the DOE technical and cost targets. Significant emphasis was placed on characterization of the material and full scale molding demonstrations.

Roberts, George; Parsons, Jason; Friedman, Jake

2010-12-17T23:59:59.000Z

53

Rotary kiln seal  

SciTech Connect (OSTI)

A rotary seal used to prevent the escape of contaminates from a rotating kiln incinerator. The rotating seal combines a rotating disc plate which is attached to the rotating kiln shell and four sets of non-rotating carbon seal bars housed in a primary and secondary housing and which rub on the sides of the disc. A seal air system is used to create a positive pressure in a chamber between the primary and secondary seals to create a positive air flow into the contaminated gas chamber. The seal air system also employs an air inlet located between the secondary and tertiary seals to further insure that no contaminates pass the seal and enter the external environment and to provide makeup air for the air which flows into the contaminated gas chamber. The pressure exerted by the seal bars on the rotating disc is controlled by means of a preload spring. The seal is capable of operating in a thermally changing environment where the both radial expansion and axial movement of the rotating kiln do not result in the failure of the seal.

Drexler, Robert L. (Idaho Falls, ID)

1992-01-01T23:59:59.000Z

54

Low Cost, Durable Seal  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Cost, Durable Seal Cost, Durable Seal George M. Roberts UTC Power Corporation February 14, 2007 This presentation does not contain any proprietary or confidential information 1 LOW COST, DURABLE SEAL Outline * Project Objective * Technical Approach * Timeline * Team Roles * Budget * Q&A 2 LOW COST, DURABLE SEAL Project Objective Develop advanced, low cost, durable seal materials and sealing techniques amenable to high volume manufacture of PEM cell stacks. DOE Targets/Goals/Objectives Project Goal Durability Transportation: 5,000 hr Stationary: 40,000 hr Durability Improve mechanical and chemical stability to achieve 40,000 hr of useful operating life. Low Cost Low Cost A material cost equivalent to or less than the cost of silicones in common use. 3 LOW COST, DURABLE SEAL

55

Shaft seal system  

DOE Patents [OSTI]

A shaft seal system is disclosed for isolating two regions of different fluid mediums through which a rotatable shaft extends. The seal system includes a seal housing through which the shaft extends and which defines an annular land and an annular labyrinth both of which face on the shaft so that each establishes a corresponding fluid sealing annulus. A collection cavity is formed in communication with the annular sealing spaces, and fluids compatible with the fluids in each of the two regions to be isolated are introduced, respectively, into the annular sealing spaces and collected in the collection cavity from which the fluid mixture is removed and passed to a separator which separates the fluids and returns them to their respective annular sealing spaces in a recycling manner. In the illustrated embodiment, the isolated fluid mediums comprise a liquid region and a gas region. Gas is removed from the gas region and passed through a purifier and a gas pump operative to introduce the purified gas through the labyrinth sealing annulus to the collection cavity. After passing to the separator, the separated gas is passed through a dryer from which the dried gas is caused to pass through the labyrinth sealing annulus into the collection cavity independently of the purified gas so as to insure isolation of the gas region in the event of sealing gas pump malfunction.

Kapich, Davorin D. (Carlsbad, CA)

1985-01-01T23:59:59.000Z

56

Mechanically expandable annular seal  

DOE Patents [OSTI]

A mechanically expandable annular reusable seal assembly to form an annular hermetic barrier between two stationary, parallel, and planar containment surfaces is described. A rotatable ring, attached to the first surface, has ring wedges resembling the saw-tooth array of a hole saw. Matching seal wedges are slidably attached to the ring wedges and have their motion restricted to be perpendicular to the second surface. Each seal wedge has a face parallel to the second surface. An annular elastomer seal has a central annular region attached to the seal wedges' parallel faces and has its inner and outer circumferences attached to the first surface. A rotation of the ring extends the elastomer seal's central region perpendicularly towards the second surface to create the fluid tight barrier. A counter rotation removes the barrier. 6 figs.

Gilmore, R.F.

1983-07-19T23:59:59.000Z

57

Damped flexible seal  

DOE Patents [OSTI]

A damped flexible seal assembly for a torpedo isolates the tailcone thereof rom vibrational energy present in the drive shaft assembly. A pair of outside flanges, each of which include an inwardly facing groove and an O-ring constrained therein, provide a watertight seal against the outer non-rotating surface of the drive shaft assembly. An inside flange includes an outwardly-facing groove and an O-ring constrained therein, and provides a watertight seal against the inner surface of the tail cone. Two cast-in-place elastomeric seals provide a watertight seal between the flanges and further provide a damping barrier between the outside flanges and the inside flanges for damping vibrational energy present in the drive shaft assembly before the energy can reach the tailcone through the seal assembly.

DuBois, Neil J. (Cranston, RI); Amaral, Antonio M. (Barrington, RI)

1992-10-27T23:59:59.000Z

58

Liquid zone seal  

DOE Patents [OSTI]

A seal assembly that provides a means for establishing multiple pressure zones within a system. The seal assembly combines a plate extending from the inner wall of a housing or inner enclosure that intersects with and is immersed in the fluid contained in a well formed in a tray contained within the enclosure. The fluid is a low vapor pressure oil, chemically inert and oxidation resistant. The use of a fluid as the sealing component provides a seal that is self-healing and mechanically robust not subject to normal mechanical wear, breakage, and formation of cracks or pinholes and decouples external mechanical vibrations from internal structural members.

Klebanoff, Leonard E. (Dublin, CA)

2001-01-01T23:59:59.000Z

59

Low Cost, Durable Seal  

Broader source: Energy.gov [DOE]

This presentation, which focuses on low cost, durable seals, was given by George Roberts of UTC Power at a February 2007 meeting on new fuel cell projects.

60

Rotary shaft seal  

DOE Patents [OSTI]

The invention is a novel rotary shaft seal assembly which provides positive-contact sealing when the shaft is not rotated and which operates with its sealing surfaces separated by a film of compressed ambient gas whose width is independent of the speed of shaft rotation. In a preferred embodiment, the assembly includes a disc affixed to the shaft for rotation therewith. Axially movable, non-rotatable plates respectively supported by sealing bellows are positioned on either side of the disc to be in sealing engagement therewith. Each plate carries piezoelectric transducer elements which are electrically energized at startup to produce films of compressed ambient gas between the confronting surfaces of the plates and the disc. Following shutdown of the shaft, the transducer elements are de-energized. A control circuit responds to incipient rubbing between the plate and either disc by altering the electrical input to the transducer elements to eliminate rubbing.

Langebrake, Clair O. (Waverly, OH)

1984-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "aerosol-based duct sealing" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


61

Repository seals requirement study  

SciTech Connect (OSTI)

The Yucca Mountain Site Characterization Project, managed by the Civilian Radioactive Waste Management System (CRWMS) Management and Operating Contractor (M and O) is conducting investigations to support the Viability Assessment and the License Application for a high-level nuclear waste repository at Yucca Mountain, Nevada. The sealing subsystem is part of the Yucca Mountain Waste Isolation System. The Yucca Mountain Site Characterization Project is currently evaluating the role of the sealing subsystem (shaft, ramp and exploratory borehole seals) in achieving the overall performance objectives for the Waste Isolation System. This report documents the results of those evaluations. The objective of the study is to provide water or air flow performance based requirements for shafts, ramps, and exploratory boreholes located near the repository. Recommendations, as appropriate, are provided for developing plans, seals component testing, and other studies relating to sealing.

NONE

1997-11-03T23:59:59.000Z

62

Rotary shaft seal  

DOE Patents [OSTI]

The invention is a novel rotary shaft seal assembly which provides positive-contact sealing when the shaft is not rotated and which operates with its sealing surfaces separated by a film of compressed ambient gas whose width is independent of the speed of shaft rotation. In a preferred embodiment, the assembly includes a disc affixed to the shaft for rotation therewith. Axially movable, non-rotatable plates respectively supported by sealing bellows are positioned on either side of the disc to be in sealing engagement therewith. Each plate carries piezoelectric transucer elements which are electrically energized at startup to produce films of compressed ambient gas between the confronting surfaces of the plates and the disc. Following shutdown of the shaft, the transducer elements are de-energized. A control circuit responds to incipient rubbing between the plate and either disc by altering the electrical input to the transducer elements to eliminate rubbing.

Langebrake, C.O.

1984-01-01T23:59:59.000Z

63

Articulated transition duct in turbomachine  

SciTech Connect (OSTI)

Turbine systems are provided. A turbine system includes a transition duct comprising an inlet, an outlet, and a duct passage extending between the inlet and the outlet and defining a longitudinal axis, a radial axis, and a tangential axis. The outlet of the transition duct is offset from the inlet along the longitudinal axis and the tangential axis. The duct passage includes an upstream portion and a downstream portion. The upstream portion extends from the inlet between an inlet end and an aft end. The downstream portion extends from the outlet between an outlet end and a head end. The turbine system further includes a joint coupling the aft end of the upstream portion and the head end of the downstream portion together. The joint is configured to allow movement of the upstream portion and the downstream portion relative to each other about or along at least one axis.

Flanagan, James Scott; McMahan, Kevin Weston; LeBegue, Jeffrey Scott; Pentecost, Ronnie Ray

2014-04-29T23:59:59.000Z

64

Choosing and Using Seals  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Appeared in Army Sustainment 44, 54-58 (2012) Appeared in Army Sustainment 44, 54-58 (2012) How to Choose and Use Seals Roger G. Jo rner, Ph.D. h a Vulnerabilit nston, Ph.D., CPP and Jon S. W y Assessment Team Argonne National Laboratory 9700 S. Cass Ave, Building 206 Argonne, IL 60439-4840 630-252-6168, rogerj@anl.gov Introduction Tamper-indicating seals have been in use for well over 7,000 years.[1,2] Today, seals are widely used for a variety of applications including cargo security, nuclear safeguards, counter-

65

SEALING SIMULATED LEAKS  

SciTech Connect (OSTI)

This report details the testing equipment, procedures and results performed under Task 7.2 Sealing Simulated Leaks. In terms of our ability to seal leaks identified in the technical topical report, Analysis of Current Field Data, we were 100% successful. In regards to maintaining seal integrity after pigging operations we achieved varying degrees of success. Internal Corrosion defects proved to be the most resistant to the effects of pigging while External Corrosion proved to be the least resistant. Overall, with limitations, pressure activated sealant technology would be a viable option under the right circumstances.

Michael A. Romano

2004-09-01T23:59:59.000Z

66

Multilayer compressive seal for sealing in high temperature devices  

DOE Patents [OSTI]

A mica based compressive seal has been developed exhibiting superior thermal cycle stability when compared to other compressive seals known in the art. The seal is composed of compliant glass or metal interlayers and a sealing (gasket) member layer composed of mica that is infiltrated with a glass forming material, which effectively reduces leaks within the seal. The compressive seal shows approximately a 100-fold reduction in leak rates compared with previously developed hybrid seals after from 10 to about 40 thermal cycles under a compressive stress of from 50 psi to 100 psi at temperatures in the range from 600.degree. C. to about 850.degree. C.

Chou, Yeong-Shyung (Richland, WA); Stevenson, Jeffry W. (Richland, WA)

2007-08-21T23:59:59.000Z

67

TWO NEW DUCT LEAKAGE TESTS  

SciTech Connect (OSTI)

Two variations on the tests for duct leakage currently embodied in ASHRAE Standard 152P (Method of Test for Determining the Design and Seasonal Efficiencies of Residential Thermal Distribution Systems) are presented. Procedures are derived for calculating supply and return duct leakage to/from outside using these new variations. Results of these tests are compared with the original ones in Standard 152P on the basis of data collected in three New York State homes.

ANDREWS,J.W.

1998-12-01T23:59:59.000Z

68

Flexible cloth seal assembly  

DOE Patents [OSTI]

A seal assembly is described having a flexible cloth seal which includes a shim assemblage surrounded by a cloth assemblage. A first tubular end portion, such as a gas turbine combustor, includes a longitudinal axis and has smooth and spaced-apart first and second surface portions defining a notch there between which is wider at its top than at its bottom and which extends outward from the axis. The second surface portion is outside curved, and a first edge of the cloth seal is positioned in the bottom of the notch. A second tubular end portion, such as a first stage nozzle, is located near, spaced apart from, and coaxially aligned with, the first tubular end portion. The second tubular end portion has a smooth third surface portion which surrounds at least a portion of the first tubular end portion and which is contacted by the cloth seal. 7 figs.

Bagepalli, B.S.; Taura, J.C.; Aksit, M.F.; Demiroglu, M.; Predmore, D.R.

1999-06-29T23:59:59.000Z

69

Turbine seal assembly  

DOE Patents [OSTI]

A seal assembly that limits gas leakage from a hot gas path to one or more disc cavities in a turbine engine. The seal assembly includes a seal apparatus that limits gas leakage from the hot gas path to a respective one of the disc cavities. The seal apparatus comprises a plurality of blade members rotatable with a blade structure. The blade members are associated with the blade structure and extend toward adjacent stationary components. Each blade member includes a leading edge and a trailing edge, the leading edge of each blade member being located circumferentially in front of the blade member's corresponding trailing edge in a direction of rotation of the turbine rotor. The blade members are arranged such that a space having a component in a circumferential direction is defined between adjacent circumferentially spaced blade members.

Little, David A.

2013-04-16T23:59:59.000Z

70

Geopolymer Sealing Materials  

Broader source: Energy.gov [DOE]

DOE Geothermal Peer Review 2010 - Presentation. Project objectives: Develop and characterize field-applicable geopolymer temporary sealing materials in the laboratory and to transfer this developed material technology to geothermal drilling service companies as collaborators for field validation tests.

71

Rotatable seal assembly  

DOE Patents [OSTI]

An assembly is provided for rotatably supporting a rotor on a stator so that vacuum chambers in the rotor and stator remain in communication while the chambers are sealed from ambient air, which enables the use of a ball bearing or the like to support most of the weight of the rotor. The apparatus includes a seal device mounted on the rotor to rotate therewith, but shiftable in position on the rotor while being sealed to the rotor as by an O-ring. The seal device has a flat face that is biased towards a flat face on the stator, and pressurized air is pumped between the faces to prevent contact between them while spacing them a small distance apart to avoid the inflow of large amounts of air between the faces and into the vacuum chambers.

Logan, Clinton M. (Pleasanton, CA); Garibaldi, Jack L. (Livermore, CA)

1982-01-01T23:59:59.000Z

72

Moisture performance of sealed attics in the mixed-humid climate  

SciTech Connect (OSTI)

Oak Ridge National Laboratory studied 8 homes in the mixed-humid climate, 4 with vented attics and 4 with sealed attics. ORNL wanted to understand the moisture performance of the sealed attic and how it affected the interior environment. We found that the attic and interior of sealed attic homes were more humid than the attic and interior observed in vented attic homes. This is due to the lack of ventilation in the sealed attic. Historically attics have been vented to dehumidify the attic and interior of the home. A sealed attic design greatly reduces the venting potential and thus this drying pathway and can cause elevated interior moisture over a vented attic home. Despite the elevated attic and interior moisture in the sealed attic homes, so far no mold or material degradation has been found. The roof sheathing moisture content has stayed below 20%, indicating low potential for material degradation. Also the relative humidity at the roof sheathing has stayed within the ASHRAE 160 design criteria except for a short time during the 2011/2012 winter. This was due to a combination of the sealed attic design (minimal venting to the outside) and the duct work not being operated in the attic which usually provides a dehumidification pathway. It was also found that when the humidity was controlled using the HVAC system, it resulted in 7% more cooling energy consumption. In the mixed-humid climate this reduces the cost effectiveness of the sealed attic design as a solution for bringing ducts into a semi-conditioned space. Because of this we are recommending the other alternatives be used to bringing ducts into the conditioned space in both new construction and retrofit work in the mixed-humid climate.

Boudreaux, Philip R [ORNL] [ORNL; Pallin, Simon B [ORNL] [ORNL; Jackson, Roderick K [ORNL] [ORNL

2013-12-01T23:59:59.000Z

73

Applauding the performing seal  

SciTech Connect (OSTI)

Whether the culprit is a pump, valve, compressor, or flanged pipe connection, the end result is the same: process-fluid leakage damages the environment and is costly to operators, in terms of lost product, lost production due to downtime, and the replacement of damaged process equipment. Hard-to-handle fluids, such as abrasive slurries of coal and flyash, can damage the seals that contain them, allowing potentially harmful fluids to escape. Even more insidious is the often-invisible escape of volatile organic compounds (VOCs) from equipment that handles liquid petroleum, petroleum by-products and chemicals. This paper reports that seal manufacturers are using their ingenuity to minimize the escape of liquid and gaseous emissions. One approach uses the power of magnetic attraction to create a seal along a rotating pump shaft by positioning magnetic fluids there. Ferrofluidics Corp. starts by creating a magnetic fluid - essentially a colloidal suspension of ultrafine magnetic salts dispersed in a carrier fluid - which is then used as a liquid O-ring seal in conjunction with a mechanical seal. The seal apparatus consists of a doughnut-shaped sandwich (centered around the pump shaft), with a permanent magnet as the middle layer, and a washer of magnetically permeable material on either side.

Not Available

1992-03-01T23:59:59.000Z

74

What are the requirements for duct leakage testing? | Building Energy Codes  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

requirements for duct leakage testing? requirements for duct leakage testing? Both the 2009 and 2012 IECC require duct tightness to be verified. Verification can take place via either a post-construction test or a rough-in test. For the post-construction test, leakage measurement must be made across the entire system, including the manufacturer's air handler enclosure, with all register boots taped or sealed at a test pressure of 0.1 inches w.g. (25 Pa). The 2009 IECC limits the leakage to outdoors to less than or equal to 8 cfm per 100 ft2 of conditioned floor area or total leakage less than or equal to 12 cfm per 100 ft2 of conditioned floor area. The 2012 IECC only contains a requirement for total leakage of less than or equal to 4 cfm per 100 ft2 of conditioned floor area. For the rough-in test, leakage measurement is made across the system, with

75

Duct leakage measurement and analysis  

SciTech Connect (OSTI)

Leakage measurements were made on 6-in. (150-mm) and 10-in. (250-mm) round and 14-in. by 6-in. (350-mm by 150-mm) and 22-in. by 8-in. (560-mm by 200-mm) rectangular ducts for both positive and negative internal pressures. The data were found to fit a power law model, with the leakage rate (Q) increasing with a power, n, of static pressure difference ({Delta}p), i.e., Q {proportional_to} ({Delta}p){sup n}. A convenient leakage prediction equation, Q = C ({Delta}p*){sup n}, uses a normalized pressure difference, {Delta}p* = {Delta}p/{Delta}p{sub ref}, with {Delta}p in in. wg (Pa) and a reference pressure difference, {Delta}p{sub ref}, of 1 in. wg (250 Pa). C{sub D}, the recommended design values of C for a repetitive element of a duct system--one duct section and one joint, ranged from 0.01 cfm (0.005 L/s) for a Vanstone flanged joint to 18.5 cfm (8.7 L/s) for an unsealed 22-in. by 8-in (560-mm by 200-mm) duct with a slip-and-drive joint. Most test ducts had C{sub D} values of 6 to 8 cfm (3 to 4 L/s) and had values of n close to 0.58. Joints were found to account for most of the leakage, and thus most of the value of C{sub D}, in unsealed ducts, with seams contributing only 10% to 38% of the total.

Swim, W.B.; Griggs, E.I. [Tennessee Technological Univ., Cookeville, TN (United States). Dept. of Mechanical Engineering

1995-08-01T23:59:59.000Z

76

Seal system with integral detector  

DOE Patents [OSTI]

There is disclosed a seal system for materials where security is of the essence, such as nuclear materials, which is tamper-indicating, which indicates changes in environmental conditions that evidence attempts to by-pass the seal, which is unique and cost effective, said seal system comprised of a seal where an optical signal is transmitted through a loop, with a detector to read said signal, and one or more additional detectors designed to detect environmental changes, these detectors being operatively associated with the seal so that detection of a break in the optical signal or detection of environmental changes will cause an observable change in the seal.

Fiarman, Sidney (Port Jefferson, NY)

1985-01-01T23:59:59.000Z

77

Flat Oval Spiral Duct Deflection  

E-Print Network [OSTI]

(c) 20 Gauge and 48 inch Flat Span (d) 24 Gauge and 6 inch Flat Span (e) 24 Gauge and 14 inch Flat Span (f) 26 Gauge and 25 inch Flat Span Figure 7.2.: Unreinforced Positive 35 (g) (cont.) 18 Gauge and 63 inch Flat Span (h) (cont.) 20 Gauge and 14.... [18] Ducts can be used in many applications some; applications might be high temperature or even corrosive or abrasive. Ducts are generally used in industrial ventilation, air pollution, and dust collecting systems. Metals can corrode from chemicals...

Daugherty, Matthew

2014-03-10T23:59:59.000Z

78

Building Energy Software Tools Directory: Duct Calculator  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Duct Calculator Duct Calculator Duct Calculator logo. Provides access to duct calculation and sizing capabilities either as a standalone Windows program or from within the Autodesk Building Mechanical, the new HVAC-oriented version of AutoCAD. Based on the engineering data and procedures outlined in the ASHRAE Fundamentals Handbook Calculation Methods, Duct Calculator features an advanced and fully interactive user interface. Slide controls for air flow, velocity, friction and duct size provide real-time, interactive feedback; as you spin one, the others dynamically respond in real time. When used with Autodesk Building Mechanical, Duct Calculator streamlines the design process by automatically re-sizing whole branches of ductwork. Screen Shots Keywords duct-sizing, design, engineering, calculation

79

Sealing coupling. [LMFBR  

DOE Patents [OSTI]

Disclosed is a remotely operable releasable sealing coupling which provides fluid-tight joinder of upper and a lower conduit sections. Each conduit section has a concave conical sealing surface adjacent its end portion. A tubular sleeve having convex spherical ends is inserted between the conduit ends to form line contact with the concave conical end portions. An inwardly projecting lip located at one end of the sleeve cooperates with a retaining collar formed on the upper pipe end to provide swivel capture for the sleeve. The upper conduit section also includes a tapered lower end portion which engages the inside surface of the sleeve to limit misalignment of the connected conduit sections.

Pardini, J.A.; Brubaker, R.C.; Rusnak, J.J.

1982-09-20T23:59:59.000Z

80

AIR SEALING Seal air leaks and save energy!  

E-Print Network [OSTI]

AIR SEALING Seal air leaks and save energy! W H A T I S A I R L E A K A G E ? Ventilation is fresh at stopping air leakage. It is critical to seal all holes and seams between these sheet goods with durable air that enters a house in a controlled manner to exhaust excess moisture and reduce odors

Oak Ridge National Laboratory

Note: This page contains sample records for the topic "aerosol-based duct sealing" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


81

Microsoft PowerPoint - Rev.R3aPassive High-Temperature Sealing Device TechBriefp1.ppt  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Passive High-Temperature Sealing Device Passive High-Temperature Sealing Device at a glance  temperature activated  provides circumferential sealing  maintains continuous force  conforms to irregular shapes and surface conditions  expands to fill large gaps  U. S. Patent 7,503,594 To use as a seal, the ring can be inserted inside a pipe with the thinner wall in contact with the inner wall of the pipe. High temperature will cause the thinner wall to expand outward, providing a tight seal against the pipe. The expanding ring wall will accommodate irregularities in the pipe wall. Seals process lines A sealing device has been designed to act as a high-temperature shutoff valve for pipes and ducts. This passive device can be used to stop the flow of gas or liquid in conditions of sudden

82

GlassMelt&Sealing  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Glass Melting and Sealing Glass Melting and Sealing Manufacturing Technologies The Manufacturing Science & Technology Center performs process development of glass and glass-ceramic-to-metal seals. Small batches of specialty glass can be melted from reagent grade oxide powders. Glass and glass-ceramic-to-metal seals are made in microprocessor controlled inert atmospheres and are checked for her- meticity after sealing. Sandia's extensive properties database of low melting solder glasses is used to aid in material and processing decisions when making glass-to-glass, ceramic-to-ceramic, and glass-to-ceramic seals. These seals are typically done in air at much lower tem- peratures than glass and glass-to-ceramic seals. Capabilities * Interface with designers and vendors to assure that the most appropriate materi-

83

Static seal for turbine engine  

DOE Patents [OSTI]

A seal structure for a gas turbine engine, the seal structure including first and second components located adjacent to each other and forming a barrier between high and low pressure zones. A seal cavity is defined in the first and second components, the seal cavity extending to either side of an elongated gap extending generally in a first direction between the first and second components. A seal member is positioned within the seal cavity and spans across the elongated gap. The seal member includes first and second side edges extending into each of the components in a second direction transverse to the first direction, and opposing longitudinal edges extending between the side edges generally parallel to the first direction. The side edges include a groove formed therein for effecting a reduction of gas flow around the seal member at the side edges.

Salazar, Santiago; Gisch, Andrew

2014-04-01T23:59:59.000Z

84

CALIFORNIA ENERGY Residential Duct Placement  

E-Print Network [OSTI]

CALIFORNIA ENERGY COMMISSION Residential Duct Placement: Market Barriers Market Barriers, Governor #12;#12;CALIFORNIA ENERGY COMMISSION Prepared By: GARD Analytics, Inc. Roger Hedrick, Lead Author DISCLAIMER This report was prepared as the result of work sponsored by the California Energy Commission

85

Sealed Radioactive Source Accountability  

Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

This Notice extends DOE N 5400.9, Sealed Radioactive Source Accountability, of 12-24-91, until 12-24-95, unless sooner superseded or rescinded. The contents of DOE N 5400.9 will be updated and incorporated in the revised DOE O 5480.11, Radiation Protection for Occupational Workers.

1994-12-22T23:59:59.000Z

86

Sealed Radioactive Source Accountability  

Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

To establish Department of Energy (DOE) interim policy and to provide guidance for sealed radioactive source accountability. The directive does not cancel any directives. Extended by DOE N 5400.10 to 12-24-93 & Extended by DOE N 5400.12 to 12-24-94.

1991-12-24T23:59:59.000Z

87

Department Seal and Flag  

Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

This directive sets forth the policy governing the use of the official seal and distinguishing flag of the Department of Energy (DOE) as described in Title 10, Code of Federal Regulations (CFR), Part 1002. Cancels DOE O 10002.A dated 1-8-90.

1992-05-18T23:59:59.000Z

88

Design of Flexible-Duct Junction Boxes  

Broader source: Energy.gov (indexed) [DOE]

Design of Flexible-duct Design of Flexible-duct Junction Boxes Robert Beach, IBACOS Duncan Prahl, IBACOS Design of Flexible-duct Junction Boxes Presentation Outline * Current Standards and Practice * Analysis Methods * Recommendations Design of Flexible-duct Junction Boxes * Detailed report is in peer review anticipated to be published T3 this year. - http://www1.eere.energy.gov/library/default.aspx?page=2&spi d=2. * Measure guide to be part of Building America Solutions Center - http://basc.pnnl.gov/ Design of Flexible-duct Junction Boxes Typical Installations As Plenum As Monster Design of Flexible-duct Junction Boxes Current Standards * ASHRAE 2012 HVAC Systems and Equipment, Box Plenum Systems Using Flexible Duct - Constrains Box Width to 2-3x Entrance Width - Constrains Box Length to 2 x Box Width

89

Regenerator cross arm seal assembly  

DOE Patents [OSTI]

A seal assembly for disposition between a cross arm on a gas turbine engine block and a regenerator disc, the seal assembly including a platform coextensive with the cross arm, a seal and wear layer sealingly and slidingly engaging the regenerator disc, a porous and compliant support layer between the platform and the seal and wear layer porous enough to permit flow of cooling air therethrough and compliant to accommodate relative thermal growth and distortion, a dike between the seal and wear layer and the platform for preventing cross flow through the support layer between engine exhaust and pressurized air passages, and air diversion passages for directing unregenerated pressurized air through the support layer to cool the seal and wear layer and then back into the flow of regenerated pressurized air.

Jackman, Anthony V. (Indianapolis, IN)

1988-01-01T23:59:59.000Z

90

Bellows sealed plug valve  

DOE Patents [OSTI]

A bellows sealed plug valve includes a valve body having an inlet passage and an outlet passage, a valve chamber between the inlet and outlet passages. A valve plug has substantially the same shape as the valve chamber and is rotatably disposed therein. A shaft is movable linearly in response to a signal from a valve actuator. A bellows is sealingly disposed between the valve chamber and the valve actuator and means are located between the bellows and the valve plug for converting linear movement of the shaft connected to the valve actuator to rotational movement of the plug. Various means are disclosed including helical thread mechanism, clevis mechanism and rack and pinion mechanism, all for converting linear motion to rotational motion.

Dukas, Jr., Stephen J. (Idaho Falls, ID)

1990-01-01T23:59:59.000Z

91

Flameless tube sealing apparatus  

SciTech Connect (OSTI)

A flameless sealer for glass and polymeric tubes uses a circular filament as a heating element and can be used for sealing relatively large diameter tubes while they are within a glovebox or other protected enclosure. The electrically conductive rods extending from a non-conductive base which defines an aperture for mounting the apparatus to a lattice rod of a glove box. A remotely located power supply provides electrical power to the filament. 2 figs.

McFarlan, J.T.; Zwick, B.D.; Avens, L.R.

1991-03-04T23:59:59.000Z

92

Metal to ceramic sealed joint  

DOE Patents [OSTI]

A metal to ceramic sealed joint which can withstand wide variations in temperature and maintain a good seal is provided for use in a device adapted to withstand thermal cycling from about 20 to about 1000 degrees C. The sealed joint includes a metal member, a ceramic member having an end portion, and an active metal braze forming a joint to seal the metal member to the ceramic member. The joint is positioned remote from the end portion of the ceramic member to avoid stresses at the ends or edges of the ceramic member. The sealed joint is particularly suited for use to form sealed metal to ceramic joints in a thermoelectric generator such as a sodium heat engine where a solid ceramic electrolyte is joined to metal parts in the system.

Lasecki, John V. (Livonia, MI); Novak, Robert F. (Farmington Hills, MI); McBride, James R. (Ypsilanti, MI)

1991-01-01T23:59:59.000Z

93

Metal to ceramic sealed joint  

DOE Patents [OSTI]

A metal to ceramic sealed joint which can withstand wide variations in temperature and maintain a good seal is provided for use in a device adapted to withstand thermal cycling from about 20 to about 1000 degrees C. The sealed joint includes a metal member, a ceramic member having an end portion, and an active metal braze forming a joint to seal the metal member to the ceramic member. The joint is positioned remote from the end portion of the ceramic member to avoid stresses at the ends or edges of the ceramic member. The sealed joint is particularly suited for use to form sealed metal to ceramic joints in a thermoelectric generator such as a sodium heat engine where a solid ceramic electrolyte is joined to metal parts in the system. 11 figures.

Lasecki, J.V.; Novak, R.F.; McBride, J.R.

1991-08-27T23:59:59.000Z

94

Rim seal for turbine wheel  

DOE Patents [OSTI]

A turbine wheel assembly includes a disk having a plurality of blades therearound. A ceramic ring is mounted to the housing of the turbine wheel assembly. A labyrinth rim seal mounted on the disk cooperates with the ceramic ring to seal the hot gases acting on the blades from the disk. The ceramic ring permits a tighter clearance between the labyrinth rim seal and the ceramic ring.

Glezer, Boris (Del Mar, CA); Boyd, Gary L. (Alpine, CA); Norton, Paul F. (San Diego, CA)

1996-01-01T23:59:59.000Z

95

Simulated Climatology of Atmospheric Ducts Over the Persian Gulf  

Science Journals Connector (OSTI)

A simulated climatology of ducts in the Persian Gulf area was produced with the MM3 atmospheric ... boundary layer prevented duct formation. Over the Gulf in the season, duct coverage was complete ... from north-...

M. Zhu; B. W. Atkinson

2005-06-01T23:59:59.000Z

96

Observations of Strong Surface Radar Ducts over the Persian Gulf  

Science Journals Connector (OSTI)

Ducting of microwave radiation is a common phenomenon over the oceans. The height and strength of the duct are controlling factors for radar propagation and must be determined accurately to assess propagation ranges. A surface evaporation duct ...

Ian M. Brooks; Andreas K. Goroch; David P. Rogers

1999-09-01T23:59:59.000Z

97

Compliant high temperature seals for dissimilar materials  

DOE Patents [OSTI]

A high temperature, gas-tight seal is formed by utilizing one or more compliant metallic toroidal ring sealing elements, where the applied pressure serves to activate the seal, thus improving the quality of the seal. The compliant nature of the sealing element compensates for differences in thermal expansion between the materials to be sealed, and is particularly useful in sealing a metallic member and a ceramic tube art elevated temperatures. The performance of the seal may be improved by coating the sealing element with a soft or flowable coating such as silver or gold and/or by backing the sealing element with a bed of fine powder. The material of the sealing element is chosen such that the element responds to stress elastically, even at elevated temperatures, permitting the seal to operate through multiple thermal cycles.

Rynders, Steven Walton (Fogelsville, PA); Minford, Eric (Laurys Station, PA); Tressler, Richard Ernest (Boalsburg, PA); Taylor, Dale M. (Salt Lake City, UT)

2001-01-01T23:59:59.000Z

98

Refractory Glass Seals for SOFC  

SciTech Connect (OSTI)

One of the critical challenges facing planar solid oxide fuel cell (SOFC) technology is the need for reliable sealing technology. Seals must exhibit long-term stability and mechanical integrity in the high temperature SOFC environment during normal and transient operation. Several different approaches for sealing SOFC stacks are under development, including glass or glass-ceramic seals, metallic brazes, and compressive seals. Among glass seals, rigid glass-ceramics, self-healing glass, and composite glass approaches have been investigated under the SECA Core Technology Program. The U.S. Department of Energy's Pacific Northwest National Laboratory (PNNL) has developed the refractory glass approach in light of the fact that higher sealing temperatures (e.g., 930-1000 degrees C) may enhance the ultimate in-service bulk strength and electrical conductivity of contact materials, as well as the bonding strength between contact materials and adjacent SOFC components, such as interconnect coatings and electrodes. This report summarizes the thermal, chemical, mechanical, and electrical properties of the refractory sealing glass.

Chou, Y. S.; Stevenson, Jeffry W.

2011-07-01T23:59:59.000Z

99

Case Study of Envelope Sealing in Existing Multiunit Structures  

SciTech Connect (OSTI)

Envelope air sealing was included in the retrofit of a 244 unit low-rise multifamily housing complex in Durham, N.C. Pre- and post-retrofit enclosure leakage tests were conducted on 51 units and detailed diagnostics were performed on 16. On average, total leakage was reduced by nearly half, from 19.7 ACH50 to 9.4 ACH50. Costs for air sealing were $0.31 per square foot of conditioned floor area, lower than estimates found in the National Residential Efficiency Measures Database (NREMD) and other sources, perhaps due in part to the large-scale production nature of the project. Modeling with BEopt software -- using an estimate of 85% of the envelope air leakage going to the outside (based on guarded tests performed at the site) -- calculated a space conditioning energy cost savings of 15% to 21% due to the air sealing retrofit. Important air leakage locations identified included plumbing and electrical penetrations, dropped ceilings/soffits, windows, ducts and wall-to-floor intersections. Previous repair activity had created significant leakage locations as well. Specifications and a pictorial guide were developed for contractors performing the work.

Dentz, J.; Conlin, F.; Podorson, D.

2012-10-01T23:59:59.000Z

100

Buried and Encapsulated Ducts - Building America Top Innovation...  

Broader source: Energy.gov (indexed) [DOE]

and Encapsulated Ducts - Building America Top Innovation photo of worker blowing insulation on ducts in an attic. Ductwork installed in unconditioned attics can significantly...

Note: This page contains sample records for the topic "aerosol-based duct sealing" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


101

Integration of HVAC System Design with Simplified Duct Distribution...  

Broader source: Energy.gov (indexed) [DOE]

Integration of HVAC System Design with Simplified Duct Distribution - Building America Top Innovation Integration of HVAC System Design with Simplified Duct Distribution - Building...

102

Tips for specifying active duct silencers  

Science Journals Connector (OSTI)

Low?frequency noise in buildings is receiving greater focus in new noise standards. The extraordinary performance of active duct silencers on these low frequencies provides a powerful new element for fan noise control. Acoustical consultants need to know the most appropriate applications for active duct silencers. The authors have been personally involved in the design and start?up of over 1000 active duct silencers installed in the USA and Europe to silence fans on a variety of HVAC applications. This site experience from office buildings schools hospitals semiconductor manufacturing facilities auditoria sound test chambers and cruise shipsboth retrofit and new constructionis summarized to guide acoustical consultants in estimating the performance of active duct silencers. Fan and duct silencer system layouts are reviewed along with performance case histories.

2000-01-01T23:59:59.000Z

103

Acoustical performance testing of duct silencers  

Science Journals Connector (OSTI)

The test method used in North America to evaluate the acoustical performance of duct silencers is ASTM E477. The ASTM standard provides an approved method for measuring the aerodynamic pressure drop dynamic insertion loss and self?generated noise of duct silencers. Unfortunately restrictions on the construction of the test duct in the current standard cause erroneous results in the measurement of insertion loss at low frequencies. These errors are due to acoustic resonances that occur naturally in the empty test duct. It is recommended that the standard be modified to require anechoic terminations at both ends of the test duct. It is also recommended that more specific design criteria for the source chamber be established and that a new section be added to provide for the measurement of the radiated noise from the casing of the test specimen. Specific recommendations relating to all of these issues will be provided.

2002-01-01T23:59:59.000Z

104

Definitions, Seals - Vulnerability Assessment Team - Nuclear Engineering  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Definitions Definitions VAT Projects Introducing the VAT Adversarial Vulnerability Assessments Safety Tags & Product Counterfeiting Election Security Spoofing GPS Defeating Existing Tamper-Indicating Seals Specialty Field Tools & Sampling Tools Insider Threat Mitigation Drug Testing Security Microprocessor Prototypes The Journal of Physical Security Vulnerability Assessments Vulnerability Assessments Insanely Fast µProcessor Shop Insanely Fast µProcessor Shop Seals About Seals Applications of Seals Common Myths about Tamper Indicating Seals Definitions Findings and Lessons Learned New Seals Types of Seals Seals References Selected VAT Papers Selected VAT Papers Selected Invited Talks Self-Assessment Survey Security Maxims Devil's Dictionary of Security Terms Argonne's VAT (brochure)

105

Seal device for ferromagnetic containers  

DOE Patents [OSTI]

A temporary seal or patch assembly prevents the escape of contents, e.g., fluids and the like, from within a container having a breach there through until the contents can be removed and/or a repair effected. A frame that supports a sealing bladder can be positioned over the breach and the frame is then attached to the container surface, which must be of a ferromagnet material, by using switchable permanent magnets. The permanent magnets are designed to have a first condition that is not attracted to the ferromagnetic surface and a second conditions whereby the magnets are attracted to the surface with sufficient force to support the seal assembly on the surface. Latching devices may be attached to the frame and engage the container surface with hardened pins to prevent the lateral movement of the seal assembly along the container surface from external forces such as fluid drag or gravity. 10 figs.

Meyer, R.E.; Jason, A.J.

1994-10-18T23:59:59.000Z

106

Seal device for ferromagnetic containers  

DOE Patents [OSTI]

A temporary seal or patch assembly prevents the escape of contents, e.g., fluids and the like, from within a container having a breach therethrough until the contents can be removed and/or a repair effected. A frame that supports a sealing bladder can be positioned over the breach and the frame is then attached to the container surface, which must be of a ferromagnet material, by using switchable permanent magnets. The permanent magnets are designed to have a first condition that is not attracted to the ferromagnetic surface and a second conditions whereby the magnets are attracted to the surface with sufficient force to support the seal assembly on the surface. Latching devices may be attached to the frame and engage the container surface with hardened pins to prevent the lateral movement of the seal assembly along the container surface from external forces such as fluid drag or gravity.

Meyer, Ross E. (Los Alamos, NM); Jason, Andrew J. (Los Alamos, NM)

1994-01-01T23:59:59.000Z

107

Fenner acquires PTFE seal manufacturer  

Science Journals Connector (OSTI)

Fenner Plc has announced the acquisition of substantially all of the operating assets and liabilities of EGC, a Houston-based manufacturer of fluoroplastic seals and other related fluoroplastic precision components.

2006-01-01T23:59:59.000Z

108

Temporary Sealing of Fractures | Open Energy Information  

Open Energy Info (EERE)

Temporary Sealing of Fractures Temporary Sealing of Fractures Jump to: navigation, search Contents 1 Geothermal Lab Call Projects for Temporary Sealing of Fractures 2 Geothermal ARRA Funded Projects for Temporary Sealing of Fractures Geothermal Lab Call Projects for Temporary Sealing of Fractures Loading map... {"format":"googlemaps3","type":"ROADMAP","types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"limit":200,"offset":0,"link":"all","sort":[""],"order":[],"headers":"show","mainlabel":"","intro":"","outro":"","searchlabel":"\u2026

109

Aerogel Impregnated Polyurethane Piping and Duct Insulation  

Broader source: Energy.gov (indexed) [DOE]

Aerogel Impregnated Polyurethane Aerogel Impregnated Polyurethane Piping and Duct Insulation David M. Hess InnoSense LLC david.hess@innosense.us, 310-530-2011 April 4, 2013 2 | Building Technologies Office eere.energy.gov Purpose & Objectives Problem Statement: Develop an efficient insulation system that will adhere to housing duct work and pipe structures while conforming to complex geometries. New insulations must increase the R-value of existing materials and be easy to apply or retrofit to existing structures.

110

Duct injection technology prototype development: Nozzle development Subtask 4. 1, Atomizer specifications for duct injection technology  

SciTech Connect (OSTI)

Babcock Wilcox has conducted a program to identify atomizers appropriate for successful in-duct injection of humidification water and lime slurries. The purpose of this program was to identify and quantify atomizer spray and performance criteria that affect the operations and reliability of the in-duct SO{sub 2} removal process, and compare commercially available atomizers to these criteria.

Not Available

1992-02-01T23:59:59.000Z

111

Radioactive material package seal tests  

SciTech Connect (OSTI)

General design or test performance requirements for radioactive materials (RAM) packages are specified in Title 10 of the US Code of Federal Regulations Part 71 (US Nuclear Regulatory Commission, 1983). The requirements for Type B packages provide a broad range of environments under which the system must contain the RAM without posing a threat to health or property. Seals that provide the containment system interface between the packaging body and the closure must function in both high- and low-temperature environments under dynamic and static conditions. A seal technology program, jointly funded by the US Department of Energy Office of Environmental Restoration and Waste Management (EM) and the Office of Civilian Radioactive Waste Management (OCRWM), was initiated at Sandia National Laboratories. Experiments were performed in this program to characterize the behavior of several static seal materials at low temperatures. Helium leak tests on face seals were used to compare the materials. Materials tested include butyl, neoprene, ethylene propylene, fluorosilicone, silicone, Eypel, Kalrez, Teflon, fluorocarbon, and Teflon/silicone composites. Because most elastomer O-ring applications are for hydraulic systems, manufacturer low-temperature ratings are based on methods that simulate this use. The seal materials tested in this program with a fixture similar to a RAM cask closure, with the exception of silicone S613-60, are not leak tight (1.0 {times} 10{sup {minus}7} std cm{sup 3}/s) at manufacturer low-temperature ratings. 8 refs., 3 figs., 1 tab.

Madsen, M.M.; Humphreys, D.L.; Edwards, K.R.

1990-01-01T23:59:59.000Z

112

Laser sealed vacuum insulating window  

DOE Patents [OSTI]

A laser sealed evacuated window panel is comprised of two glass panes held spaced apart in relation to each other by a plurality of spherical glass beads and glass welded around the edges to provide an evacuated space between the glass panes that is completely glass sealed from the exterior. The glass welded edge seal is obtained by welding the edges of the glass panes together with a laser beam while the glass panes and bead spacers are positioned in a vacuum furnace and heated to the annealing point of the glass to avoid stress fracture in the area of the glass weld. The laser welding in the furnace can be directed around the perimeter of the galss panel by a combination of rotating the glass panel and linearly translating or aiming the laser with a relay mirror.

Benson, D.K.; Tracy, C.E.

1985-08-19T23:59:59.000Z

113

Laser sealed vacuum insulation window  

DOE Patents [OSTI]

A laser sealed evacuated window panel is comprised of two glass panes held spaced apart in relation to each other by a plurality of spherical glass beads and glass welded around the edges to provide an evacuated space between the glass panes that is completely glass sealed from the exterior. The glass welded edge seal is obtained by welding the edges of the glass panes together with a laser beam while the glass panes and bead spacers are positioned in a vacuum furnace and heated to the annealing point of the glass to avoid stress fracture in the area of the glass weld. The laser welding in the furnace can be directed around the perimeter of the glass panel by a combination of rotating the glass panel and linearly translating or aiming the laser with a relay mirror.

Benson, David K. (Golden, CO); Tracy, C. Edwin (Golden, CO)

1987-01-01T23:59:59.000Z

114

Sealed source peer review plan  

SciTech Connect (OSTI)

Sealed sources are known quantities of radioactive materials that have been encapsulated in quantities that produce known radiation fields. Sealed sources have multiple uses ranging from instrument calibration sources to sources that produce radiation fields for experimental applications. The Off-Site Source Recovery (OSR) Project at Los Alamos National Laboratory (LANL), created in 1999, under the direction of the Waste Management Division of the U.S. Department of Energy (DOE) Albuquerque has been assigned the responsibility to recover and manage excess and unwanted radioactive sealed sources from the public and private sector. LANL intends to ship drums containing qualified sealed sources to the Waste Isolation Pilot Plant (WIPP) for disposal. Prior to shipping, these drums must be characterized with respect to radiological content and other parameters. The U. S. Environmental Protection Agency (EPA) requires that ten radionulcides be quantified and reported for every container of waste to be disposed in the WIPP. The methods traditionally approved by the EPA include non-destructive assay (NDA) in accordance with Appendix A of the Contact-Handled Transuranic Waste Acceptance Criteria for the Waste Isolation Pilot Plant (DOE, 2002) (CH WAC). However, because of the nature and pedigree of historical records for sealed sources and the technical infeasibility of performing NDA on these sources, LANL proposes to characterize the content of these waste drums using qualified existing radiological data in lieu of direct measurement. This plan describes the process and documentation requirements for the use of the peer review process to qualify existing data for sealed radiological sources in lieu of perfonning radioassay. The peer review process will be performed in accordance with criteria provided in 40 CFR {section} 194.22 which specifies the use of the NUREG 1297 guidelines. The plan defines the management approach, resources, schedule, and technical requirements for the subject peer review.

Feldman, Alexander [Los Alamos National Laboratory; Leonard, Lee [RETIRED; Burns, Ron [CONTRACTOR

2009-01-01T23:59:59.000Z

115

Dual rotating shaft seal apparatus  

DOE Patents [OSTI]

The report is directed to apparatus suitable for transferring torque and rotary motion through a wall in a manner which is essentially gas impermeable. The apparatus can be used for pressurizing, agitating, and mixing fluids and features two ferrofluidic, i.e., ferrometic seals. Each seal is disposed on one of two supported shafts and each shaft is operably connected at one end to a gear mechanism and at its other end to an adjustable coupling means which is to be connected to a rotatable shaft extending through a wall through which torque and rotary motion are to be transferred.

Griggs, J.E.; Newman, H.J.

1983-06-16T23:59:59.000Z

116

Experimental evaluation of pocket damper seals with brush seal elements  

E-Print Network [OSTI]

characteristics include leakage, starting torque and dynamic coefficients. The worn BHS leaks half as much as a PDS at all test pressures. The starting torque of a brush seal increases strongly with pressure, however, the power dissipated at 6,000 R.P.M. never...

Buchanan, Steven Eugene

2000-01-01T23:59:59.000Z

117

Manifold seal for fuel cell stack assembly  

DOE Patents [OSTI]

An assembly for sealing a manifold to a stack of fuel cells includes a first resilient member for providing a first sealing barrier between the manifold and the stack. A second resilient member provides a second sealing barrier between the manifold and the stack. The first and second resilient members are retained in such a manner as to define an area therebetween adapted for retaining a sealing composition.

Schmitten, Phillip F. (N. Huntingdon, PA); Wright, Maynard K. (Bethel Park, PA)

1989-01-01T23:59:59.000Z

118

Reporting of Radioactive Sealed Sources  

Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

To establish U.S. Department of Energy requirements for inventory reporting, transaction reporting, verification of reporting, and assign responsibilities for reporting of radioactive sealed sources. DOE N 251.86 extends this notice until 5-6-11. No cancellations. Canceled by DOE O 231.1B

2008-02-27T23:59:59.000Z

119

Piston rod seal for a Stirling engine  

SciTech Connect (OSTI)

In a piston rod seal for a Stirling engine, a hydrostatic bearing and differential pressure regulating valve are utilized to provide for a low pressure differential across a rubbing seal between the hydrogen and oil so as to reduce wear on the seal.

Shapiro, Wilbur (Schenectady, NY)

1984-01-01T23:59:59.000Z

120

Piston rod seal for a Stirling engine  

SciTech Connect (OSTI)

In a piston rod seal for a Stirling engine, a hydrostatic bearing and differential pressure regulating valve are utilized to provide for a low pressure differential across a rubbing seal between the hydrogen and oil so as to reduce wear on the seal. 3 figs.

Shapiro, W.

1984-01-31T23:59:59.000Z

Note: This page contains sample records for the topic "aerosol-based duct sealing" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


121

Evaluation of a New Ramping Technique for Duct Leakage Testing  

E-Print Network [OSTI]

1 LBNL-61743 Evaluation of a New Ramping Technique for Duct Leakage Testing Iain S. Walker ramping Technique for Duct Leakage Testing Table of contents Introduction......................................................................................................................... 3 DeltaQ ramping testing

122

Microsoft Word - VitPlantInstallsCrucialDuct_20110209.doc  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

also known as the "Vit Plant," set a giant heating, ventilation and air-conditioning (HVAC) duct in the High-Level Waste Facility. The nuclear-quality duct is part of the...

123

Potential Flow Calculations of Axisymmetric Ducted Wind Turbines  

E-Print Network [OSTI]

An incompressible potential-flow vortex method has been constructed to analyze the flow field of a ducted

Widnall, Sheila

2009-09-02T23:59:59.000Z

124

Handover Performance of HVAC Duct Based Indoor Wireless Networks  

E-Print Network [OSTI]

Handover Performance of HVAC Duct Based Indoor Wireless Networks A. E. Xhafa, P. Sonthikorn, and O in indoor wireless net- works (IWN) that use heating, ventilation, and air conditioning (HVAC) ducts.e., new call blocking and handover dropping probabilities, of an IWN that uses HVAC ducts are up to 6

Stancil, Daniel D.

125

Long Range Passive UHF RFID System Using HVAC Ducts  

E-Print Network [OSTI]

INVITED P A P E R Long Range Passive UHF RFID System Using HVAC Ducts To provide a potential communications channel, HVAC ducts can function as electromagnetic waveguides; a 30-m read range has been-conditioning (HVAC) ducts as a potential communication channel between passive ultrahigh-frequency (UHF) radio

Hochberg, Michael

126

CALIFORNIA ENERGY Homeowners Benefits To Ducts In  

E-Print Network [OSTI]

efficiency is improved through the integrated design, construction, and operation of building systems of Small Commercial HVAC Systems Integrated Design of Commercial Building Ceiling Systems Integrated Design of the Integrated Design of Residential Ducting & Air Flow Systems research project. The reports are a result

127

Method for sealing remote leaks in an enclosure using an aerosol  

DOE Patents [OSTI]

The invention is a method and device for sealing leaks remotely by means of injecting a previously prepared aerosol into the enclosure being sealed according to a particular sealing efficiency defined by the product of a penetration efficiency and a particle deposition efficiency. By using different limits in the relationship between penetration efficiency and flowrate, the same method according the invention can be used for coating the inside of an enclosure. Specifically the invention is a method and device for preparing, transporting, and depositing a solid phase aerosol to the interior surface of the enclosure relating particle size, particle carrier flow rate, and pressure differential, so that particles deposited there can bridge and substantially seal each leak, with out providing a substantial coating at inside surfaces of the enclosure other than the leak. The particle size and flow parameters can be adjusted to coat the interior of the enclosure (duct) without substantial plugging of the leaks depending on how the particle size and flowrate relationships are chosen.

Modera, Mark P. (Piedmont, CA); Carrie, Francois R. (Lyons, FR)

1999-01-01T23:59:59.000Z

128

Rotary seal with improved film distribution  

DOE Patents [OSTI]

The present invention is a generally circular rotary seal that establishes sealing between relatively rotatable machine components for lubricant retention and environmental exclusion, and incorporates seal geometry that interacts with the lubricant during relative rotation to distribute a lubricant film within the dynamic sealing interface. The features of a variable inlet size, a variable dynamic lip flank slope, and a reduction in the magnitude and circumferentially oriented portion of the lubricant side interfacial contact pressure zone at the narrowest part of the lip, individually or in combination thereof, serve to maximize interfacial lubrication in severe operating conditions, and also serve to minimize lubricant shear area, seal torque, seal volume, and wear, while ensuring retrofitability into the seal grooves of existing equipment.

Dietle, Lannie Laroy; Schroeder, John Erick

2013-10-08T23:59:59.000Z

129

Reducing Uncertainty for the DeltaQ Duct Leakage Test  

SciTech Connect (OSTI)

The thermal distribution system couples the HVAC components to the building envelope, and shares many properties of the buildings envelope including moisture, conduction and most especially air leakage performance. Duct leakage has a strong influence on air flow rates through building envelopes (usually resulting in much greater flows than those due to natural infiltration) because unbalanced duct air flows and leaks result in building pressurization and depressurization. As a tool to estimate this effect, the DeltaQ duct leakage test has been developed over the past several years as an improvement to existing duct pressurization tests. It focuses on measuring the air leakage flows to outside at operating conditions that are required for envelope infiltration impacts and energy loss calculations for duct systems. The DeltaQ test builds on the standard envelope tightness blower door measurement techniques by repeating the tests with the system air handler off and on. The DeltaQ test requires several assumptions to be made about duct leakage and its interaction with the duct system and building envelope in order to convert the blower door results into duct leakage at system operating conditions. This study examined improvements to the DeltaQ test that account for some of these assumptions using a duct system and building envelope in a test laboratory. The laboratory measurements used a purpose-built test chamber coupled to a duct system typical of forced air systems in US homes. Special duct leaks with controlled air-flow were designed and installed into an airtight duct system. This test apparatus allowed the systematic variation of the duct and envelope leakage and accurate measurement of the duct leakage flows for comparison to DeltaQ test results. This paper will discuss the laboratory test apparatus design, construction and operation, the various analysis techniques applied to the calculation procedure and present estimates of uncertainty in measured duct leakage.

Walker, Iain S.; Sherman, Max H.; Dickerhoff, Darryl J.

2004-05-01T23:59:59.000Z

130

About Seals - Vulnerability Assessment Team - Nuclear Engineering Division  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Seals Seals VAT Projects Introducing the VAT Adversarial Vulnerability Assessments Safety Tags & Product Counterfeiting Election Security Spoofing GPS Defeating Existing Tamper-Indicating Seals Specialty Field Tools & Sampling Tools Insider Threat Mitigation Drug Testing Security Microprocessor Prototypes The Journal of Physical Security Vulnerability Assessments Vulnerability Assessments Insanely Fast µProcessor Shop Insanely Fast µProcessor Shop Seals About Seals Applications of Seals Common Myths about Tamper Indicating Seals Definitions Findings and Lessons Learned New Seals Types of Seals Seals References Selected VAT Papers Selected VAT Papers Selected Invited Talks Self-Assessment Survey Security Maxims Devil's Dictionary of Security Terms Argonne's VAT (brochure)

131

Particle deposition in ventilation ducts: Connectors, bends anddeveloping flow  

SciTech Connect (OSTI)

In ventilation duct flow the turbulent flow profile is commonly disturbed or not fully developed and these conditions are likely to influence particle deposition to duct surfaces. Particle deposition rates at eight S-connectors, in two 90{sup o} duct bends and in two ducts where the turbulent flow profile was not fully developed were measured in a laboratory duct system with both galvanized steel and internally insulated ducts with hydraulic diameters of 15.2 cm. In the steel duct system, experiments with nominal particle diameters of 1, 3, 5, 9 and 16 {micro}m were conducted at each of three nominal air speeds: 2.2, 5.3 and 9.0 m/s. In the insulated duct system, deposition of particles with nominal diameters of 1, 3, 5, 8 and 13 {micro}m was measured at nominal air speeds of 2.2, 5.3 and 8.8 m/s. Fluorescent techniques were used to directly measure the deposition velocities of monodisperse fluorescent particles to duct surfaces. Deposition at S-connectors, in bends and in straight ducts with developing turbulence was often greater than deposition in straight ducts with fully developed turbulence for equal particle sizes, air speeds and duct surface orientations. Deposition rates at all locations were found to increase with an increase in particle size or air speed. High deposition rates at S-connectors resulted from impaction and these rates were nearly independent of the orientation of the S-connector. Deposition rates in the two 90{sup o} bends differed by more than an order of magnitude in some cases, probably because of the difference in turbulence conditions at the bend inlets. In straight steel ducts where the turbulent flow profile was developing, the deposition enhancement relative to fully developed turbulence generally increased with air speed and decreased with downstream distance from the duct inlet. This enhancement was greater at the duct ceiling and wall than at the duct floor. In insulated ducts, deposition enhancement was less pronounced overall than in steel ducts. Trends that were observed in steel ducts were present, but weaker, in insulated ducts.

Sippola, Mark R.; Nazaroff, William W.

2004-03-01T23:59:59.000Z

132

Hermetically sealed superconducting magnet motor  

DOE Patents [OSTI]

A hermetically sealed superconducting magnet motor includes a rotor separated from a stator by either a radial gap, an axial gap, or a combined axial and radial gap. Dual conically shaped stators are used in one embodiment to levitate a disc-shaped rotor made of superconducting material within a conduit for moving cryogenic fluid. As the rotor is caused to rotate when the field stator is energized, the fluid is pumped through the conduit.

DeVault, Robert C. (Knoxville, TN); McConnell, Benjamin W. (Knoxville, TN); Phillips, Benjamin A. (Benton Harbor, MI)

1996-01-01T23:59:59.000Z

133

Hermetically sealed superconducting magnet motor  

DOE Patents [OSTI]

A hermetically sealed superconducting magnet motor includes a rotor separated from a stator by either a radial gap, an axial gap, or a combined axial and radial gap. Dual conically shaped stators are used in one embodiment to levitate a disc-shaped rotor made of superconducting material within a conduit for moving cryogenic fluid. As the rotor is caused to rotate when the field stator is energized, the fluid is pumped through the conduit. 6 figs.

DeVault, R.C.; McConnell, B.W.; Phillips, B.A.

1996-07-02T23:59:59.000Z

134

Seal for fluid forming tools  

DOE Patents [OSTI]

An electro-hydraulic forming tool for forming a sheet metal blank in a one-sided die has first and second rigid rings that engage opposite sides of a sheet metal blank. The rigid rings are contained within slots on a die portion and a hydraulic force applicator portion of the forming tool. The seals are either resiliently biased by an elastomeric member or inherently resiliently biased into contact with the blank.

Golovashchenko, Sergey Fedorovich (Beverly Hills, MI); Bonnen, John Joseph Francis (Milford, MI)

2012-03-20T23:59:59.000Z

135

Findings in seal coat design  

E-Print Network [OSTI]

Africa (NITRR) and its members Dr. Claude P. Marais, Dr. Alex T. Visser and Dr. C. J. Semmelink for furnishing the relevant data and figures presented in this report. Finally this thesis and accomplishments are dedicated to my project Principal... Volume. 1. Embedment 2. Wear and Degradation. 3. Skid Resistance. 35 40 41 43 44 V SOUTH AFRICANS' RATIONAL APPROACH TO THE DESIGN OF SEAL COATS AND SURFACE TREATMENT. . 50 A. Background. B. Marais' Rational Approach. 1. Aggregate Spread Rate...

Gonzalez Palmer, Miguel Angel

1988-01-01T23:59:59.000Z

136

A New Diagnostic for Duct Leakage: DeltaQ  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

A New Diagnostic for Duct Leakage: DeltaQ A New Diagnostic for Duct Leakage: DeltaQ Speaker(s): Iain Walker Date: February 21, 2002 - 12:00pm Location: Bldg. 90 Seminar Host/Point of Contact: Cynthia Tast Duct leakage has been identified as a major contributor to HVAC energy use and building infiltration, particularly in residences. In order to make good estimates of HVAC system energy performance, we need to know how much air leaks between the ducts and outside the building during system operation. Existing methods for determining duct leakage do not perform well due to experimental procedures that produce imprecise results or they require many assumptions to convert measurements into the desired leakage flows. The DeltaQ duct leakage test has been developed by the Energy Performance of Buildings Group at LBNL to determine duct leakage flows by

137

Rationale for Measuring Duct Leakage Flows in Large Commercial Buildings  

SciTech Connect (OSTI)

Industry-wide methods of assessing duct leakage are based on duct pressurization tests, and focus on ''high pressure'' ducts. Even though ''low pressure'' ducts can be a large fraction of the system and tend to be leaky, few guidelines or construction specifications require testing these ducts. We report here on the measured leakage flows from ten large commercial duct systems at operating conditions: three had low leakage (less than 5% of duct inlet flow), and seven had substantial leakage (9 to 26%). By comparing these flows with leakage flows estimated using the industry method, we show that the latter method by itself is not a reliable indicator of whole-system leakage flow, and that leakage flows need to be measured.

Wray, Craig P.; Diamond, Richard C.; Sherman, Max H.

2005-07-01T23:59:59.000Z

138

SNM holdup assessment of Los Alamos exhaust ducts. Final report  

SciTech Connect (OSTI)

Fissile material holdup in glovebox and fume hood exhaust ducting has been quantified for all Los Alamos duct systems. Gamma-based, nondestructive measurements were used to quantify holdup. The measurements were performed during three measurement campaigns. The first campaign, Phase I, provided foot-by-foot, semiquantitative measurement data on all ducting. These data were used to identify ducting that required more accurate (quantitative) measurement. Of the 280 duct systems receiving Phase I measurements, 262 indicated less than 50 g of fissile holdup and 19 indicated fissile holdup of 50 or more grams. Seven duct systems were measured in a second campaign, called Series 1, Phase II. Holdup estimates on these ducts ranged from 421 g of {sup 235}U in a duct servicing a shut-down uranium-machining facility to 39 g of {sup 239}Pu in a duct servicing an active plutonium-processing facility. Measurements performed in the second campaign proved excessively laborious, so a third campaign was initiated that used more efficient instrumentation at some sacrifice in measurement quality. Holdup estimates for the 12 duct systems measured during this third campaign ranged from 70 g of {sup 235}U in a duct servicing analytical laboratories to 1 g of {sup 235}U and 1 g of {sup 239}Pu in a duct carrying exhaust air to a remote filter building. These quantitative holdup estimates support the conclusion made at the completion of the Phase I measurements that only ducts servicing shut-down uranium operations contain about 400 g of fissile holdup. No ventilation ducts at Los Alamos contain sufficient fissile material holdup to present a criticality safety concern.

Marshall, R.S.

1994-02-01T23:59:59.000Z

139

Air Sealing Your Home | Department of Energy  

Broader source: Energy.gov (indexed) [DOE]

Air Sealing Your Home Air Sealing Your Home Air Sealing Your Home November 26, 2013 - 6:22pm Addthis Save on heating and cooling costs by checking for air leaks in common trouble spots in your home. Save on heating and cooling costs by checking for air leaks in common trouble spots in your home. What does this mean for me? Save money and energy by air sealing your house. Caulking and weatherstripping are simple, effective ways of sealing air leaks in your home. Reducing the amount of air that leaks in and out of your home is a cost-effective way to cut heating and cooling costs, improve durability, increase comfort, and create a healthier indoor environment. Caulking and weatherstripping are two simple and effective air-sealing techniques that offer quick returns on investment, often one year or less. Caulk is

140

An Internal Coaxil Cable Seal System  

DOE Patents [OSTI]

The invention is a seal system for a coaxial cable more specifically an internal seal system placed within the coaxial cable and its constituent components. A series of seal stacks including flexible rigid rings and elastomeric rings are placed on load bearing members within the coaxial cable. The current invention is adapted to seal the annular space between the coaxial cable and an electrical contact passing there through. The coaxial cable is disposed within drilling components to transmit electrical signals between drilling components within a drill string. During oil and gas exploration, a drill string can see a range of pressures and temperatures thus resulting in multiple combinations of temperature and pressure and increasing the difficulty of creating a robust seal for all combinations. The seal system can be used in a plurality of downhole components, such as sections of pipe in a drill string, drill collars, heavy weight drill pipe, and jars.

Hall, David R. (Provo, UT); Hall, Jr., H. Tracy (Provo, UT); Pixton, David (Lehi, UT); Dahlgren, Scott (Provo, UT); Sneddon, Cameron (Provo, UT); Briscoe, Michael (Lehi, UT); Fox, Joe (Spanish Fork, UT)

2004-12-23T23:59:59.000Z

Note: This page contains sample records for the topic "aerosol-based duct sealing" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


141

Analytical and experimental investigations of a labyrinth seal test rig and damper seals for turbomachinery  

E-Print Network [OSTI]

. The test rig is also used during the development of a unique damper seal device. The experimental data used to determine the direct damping coefficient of the damper seal device are presented. Results of vibration and pressure measurements that demonstrate...

Shultz, Richard Raymond

1997-01-01T23:59:59.000Z

142

Common Myths about Tamper Indicating Seals - Vulnerability Assessment Team  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Common Myths about Tamper Common Myths about Tamper Indicating Seals VAT Projects Introducing the VAT Adversarial Vulnerability Assessments Safety Tags & Product Counterfeiting Election Security Spoofing GPS Defeating Existing Tamper-Indicating Seals Specialty Field Tools & Sampling Tools Insider Threat Mitigation Drug Testing Security Microprocessor Prototypes The Journal of Physical Security Vulnerability Assessments Vulnerability Assessments Insanely Fast µProcessor Shop Insanely Fast µProcessor Shop Seals About Seals Applications of Seals Common Myths about Tamper Indicating Seals Definitions Findings and Lessons Learned New Seals Types of Seals Seals References Selected VAT Papers Selected VAT Papers Selected Invited Talks Self-Assessment Survey Security Maxims Devil's Dictionary of Security Terms

143

Reusable tamper-indicating security seal  

SciTech Connect (OSTI)

A reusable tamper-indicating mechanical security seal for use in safeguarding nuclear material has been developed. The high-security seal displays an unpredictable, randomly selected, five-digit code each time it is used. This five digit code serves the same purpose that the serial number does for conventional non-reusable seals - a unique identifier for each use or application. The newly developed reusable seal is completely enclosed within a seamless, tamper-indicating, plastic jacket. The jacket is designed to reveal any attempts to penetrate, section or to chemically remove and replace with a counterfeit for surreptitious purposes.

Ryan, M.J.

1981-01-01T23:59:59.000Z

144

Fenner Advanced Sealing Technologies acquires AIP  

Science Journals Connector (OSTI)

In the USA, Fenner Advanced Sealing Technologies (FAST Group-Houston) has acquired American Industrial Plastics Inc (AIP), based in Daytona, Florida.

2012-01-01T23:59:59.000Z

145

Ceramic blade with tip seal  

DOE Patents [OSTI]

The present gas turbine engine includes a disc assembly defining a disc having a plurality of blades attached thereto. The disc has a preestablished rate of thermal expansion and the plurality of blades have a preestablished rate of thermal expansion being less than the preestablished rate of thermal expansion of the disc. A shroud assembly is attached to the gas turbine engine and is spaced from the plurality of blades a preestablished distance forming an interface there between. Positioned in the interface is a seal having a preestablished rate of thermal expansion being generally equal to the rate of thermal expansion of the plurality of blades. 4 figs.

Glezer, B.; Bhardwaj, N.K.; Jones, R.B.

1997-08-05T23:59:59.000Z

146

High thermal expansion, sealing glass  

DOE Patents [OSTI]

A glass composition is described for hermetically sealing to high thermal expansion materials such as aluminum alloys, stainless steels, copper, and copper/beryllium alloys, which includes between about 10 and about 25 mole percent Na[sub 2]O, between about 10 and about 25 mole percent K[sub 2]O, between about 5 and about 15 mole percent Al[sub 2]O[sub 3], between about 35 and about 50 mole percent P[sub 2]O[sub 5] and between about 5 and about 15 mole percent of one of PbO, BaO, and mixtures thereof. The composition, which may also include between 0 and about 5 mole percent Fe[sub 2]O[sub 3] and between 0 and about 10 mole percent B[sub 2]O[sub 3], has a thermal expansion coefficient in a range of between about 160 and 210[times]10[sup [minus]7]/C and a dissolution rate in a range of between about 2[times]10[sup [minus]7] and 2[times]10[sup [minus]9]g/cm[sup 2]-min. This composition is suitable to hermetically seal to metallic electrical components which will be subjected to humid environments over an extended period of time.

Brow, R.K.; Kovacic, L.

1993-11-16T23:59:59.000Z

147

Buried and Encapsulated Ducts, Jacksonville, Florida (Fact Sheet)  

SciTech Connect (OSTI)

Ductwork installed in unconditioned attics can significantly increase the overall heating and cooling costs of residential buildings. In fact, estimated duct thermal losses for single-family residential buildings with ductwork installed in unconditioned attics range from 10% to 45%. In a study of three single-story houses in Florida, the Building America research team Consortium for Advanced Residential Buildings (CARB) investigated the strategy of using buried and/or encapsulated ducts (BED) to reduce duct thermal losses in existing homes. The BED strategy consists of burying ducts in loose-fill insulation and/or encapsulating them in closed cell polyurethane spray foam (ccSPF) insulation. There are three possible combinations of BED strategies: (1) buried ducts; (2) encapsulated ducts (with ccSPF); and (3) buried and encapsulated ducts. The best solution for each situation depends on the climate, age of the house, and the configuration of the HVAC system and attic. For new construction projects, the team recommends that ducts be both encapsulated and buried as the minimal planning and costs required for this will yield optimal energy savings. The encapsulated/buried duct strategy, which utilizes ccSPF to address condensation concerns, is an approach that was developed specifically for humid climates.

Not Available

2013-11-01T23:59:59.000Z

148

Aerodynamic design considerations for a free-flying ducted propeller  

SciTech Connect (OSTI)

The design philosophy for a free-flying vehicle powered by a ducted propeller is presented from an aerodynamic viewpoint. Airframe design concentrates on duct inlet lip curvature, diffuser angle, and methods of vehicle control. Wind tunnel test results are given to evaluate two inlet designs, two exit designs, and the effect of external appendages such as a camera pod or a forebody. Finally, a simple, analytic method of ducted propeller blade design is presented and the results compared with an existing ducted propeller blade. 14 refs., 28 figs., 2 tabs.

Weir, R.J.

1988-01-01T23:59:59.000Z

149

DOE Challenge Home Technical Training- Ducts in Conditioned Space  

Broader source: Energy.gov [DOE]

A publication of the U.S. Department of Energy Challenge Home program: Design Options for Locating Ducts within Conditioned Space.

150

Cask systems development program seal technology  

SciTech Connect (OSTI)

General design or test performance requirements for radioactive materials (RAM) packages are specified in Title 10 of the US Code of Federal Regulations Part 71 (10 CFR 71). Seals that provide the containment system interface between the packaging body and the closure must function in both high- and low-temperature environments under dynamic and static conditions. Experiments were performed to characterize the performance of several seal materials at low temperatures. Helium leak tests on face seals were used to compare the materials. Materials tested include butyl, neoprene, ethylene propylene, fuorosilicone, silicone, Eypel, Kalrez, Teflon, fluorocarbon, and Teflon/silicone composites. Results show that the seal materials tested, with the exception of silicone S613-60, are not leak tight at manufacturer low-temperature ratings. This paper documents the initial series of experiments developed to characterize the performance of several static seals under conditions representative of RAM transport container environments. Helium leak rates of face seals were measured at low and ambient temperatures to compare seal materials. As scaling laws have not been developed for seals, the leakage rates measured in this program are intended to be used in a qualitative rather than quantitative manner. 5 refs., 7 figs., 2 tabs.

Madsen, M.M.; Edwards, K.R.; Humphreys, D.L.

1991-01-01T23:59:59.000Z

151

Sealing glasses for titanium and titanium alloys  

DOE Patents [OSTI]

Glass compositions containing CaO, Al/sub 2/O/sub 3/, B/sub 2/O/sub 3/, SrO and BaO of various combinations of mole % are provided. These compositions are capable of forming stable glass-to-metal seals with titanium and titanium alloys, for use in components such as seals for battery headers.

Brow, R.K.; Watkins, R.D.

1988-01-21T23:59:59.000Z

152

Sealing glasses for titanium and titanium alloys  

DOE Patents [OSTI]

Glass compositions containing CaO, Al.sub.2 O.sub.3, B.sub.2 O.sub.3, SrO and BaO of various combinations of mole % are provided. These compositions are capable of forming stable glass-to-metal seals with titanium and titanium alloys, for use in components such as seals for battery headers.

Brow, Richard K. (Albuquerque, NM); Watkins, Randall D. (Albuquerque, NM)

1992-01-01T23:59:59.000Z

153

Rotordynamic force coefficients of pocket damper seals  

E-Print Network [OSTI]

The present work describes experiments conducted on several pocket damper seal (PDS) designs using a high pressure annular gas seal test rig. Both rotating and non-rotating tests were conducted for a 12, 8, and 6 bladed PDS. The objective...

Ertas, Bugra Han

2005-11-01T23:59:59.000Z

154

STATE OF CALIFORNIA BUILDING ENVELOPE SEALING  

E-Print Network [OSTI]

STATE OF CALIFORNIA BUILDING ENVELOPE SEALING CEC- CF-4R-ENV-20 (Revised 08/09) CALIFORNIA ENERGY COMMISSION CERTIFICATE OF FIELD VERIFICATION AND DIAGNOSTIC TESTING CF-4R-ENV-20 Building Envelope Sealing.819 x (CFM50H / Conditioned Floor Area in ft2 ) per Residential ACM Manual Equation R3-16 Building

155

Memorandum, Reporting of Radiological Sealed Sources Transactions  

Broader source: Energy.gov [DOE]

The requirements for reporting transactions involving radiological sealed sources are identified in Department of Energy (DOE) Notice (N) 234.1, Reporting of Radioactive Sealed Sources. The data reported in accordance with DOE N 234.1 are maintained in the DOE Radiological Source Registry and Tracking (RSRT) database by the Office of Information Management, within the Office of Environment, Health, Safety and Security.

156

Remote Opening and Sealing of Metal Tubes  

Science Journals Connector (OSTI)

``One?shot'' methods of opening and sealing metal tubes are described. These methods were developed for taking high altitude atmospheric samples in metal bottles carried aloft by rockets and are performed by pyrotechnic means. The sealing is done by cold welding.

L. T. Loh; H. W. Neill; M. H. Nichols; E. A. Wenzel

1952-01-01T23:59:59.000Z

157

Sealing Your Home | Department of Energy  

Broader source: Energy.gov (indexed) [DOE]

Sealing Your Home Sealing Your Home Sealing Your Home Caulking can reduce heating and cooling costs and improve comfort in your home. Caulking can reduce heating and cooling costs and improve comfort in your home. Air leakage, or infiltration, occurs when outside air enters a house uncontrollably through cracks and openings. Properly air sealing can significantly reduce heating and cooling costs, improve building durability, and create a healthier indoor environment. In addition to air sealing, you'll also want to consider adding additional insulation and moisture control and ventilation strategies to ensure your home is comfortable and efficient. Featured Detecting Air Leaks For a thorough and accurate measurement of air leakage in your home, hire a qualified technician to conduct an energy assessment, particularly a blower door test.

158

Tips: Sealing Air Leaks | Department of Energy  

Broader source: Energy.gov (indexed) [DOE]

Sealing Air Leaks Sealing Air Leaks Tips: Sealing Air Leaks May 16, 2013 - 5:03pm Addthis Sources of Air Leaks in Your Home. Areas that leak air into and out of your home cost you a lot of money. The areas listed in the illustration are the most common sources of air leaks. Sources of Air Leaks in Your Home. Areas that leak air into and out of your home cost you a lot of money. The areas listed in the illustration are the most common sources of air leaks. Air leaks can waste a lot of your energy dollars. One of the quickest energy-- and money-saving tasks you can do is caulk, seal, and weather strip all seams, cracks, and openings to the outside. Tips for Sealing Air Leaks Test your home for air tightness. On a windy day, carefully hold a lit incense stick or a smoke pen next to your windows, doors, electrical

159

Tips: Sealing Air Leaks | Department of Energy  

Broader source: Energy.gov (indexed) [DOE]

Tips: Sealing Air Leaks Tips: Sealing Air Leaks Tips: Sealing Air Leaks May 16, 2013 - 5:03pm Addthis Sources of Air Leaks in Your Home. Areas that leak air into and out of your home cost you a lot of money. The areas listed in the illustration are the most common sources of air leaks. Sources of Air Leaks in Your Home. Areas that leak air into and out of your home cost you a lot of money. The areas listed in the illustration are the most common sources of air leaks. Air leaks can waste a lot of your energy dollars. One of the quickest energy-- and money-saving tasks you can do is caulk, seal, and weather strip all seams, cracks, and openings to the outside. Tips for Sealing Air Leaks Test your home for air tightness. On a windy day, carefully hold a lit incense stick or a smoke pen next to your windows, doors, electrical

160

Low thermal expansion seal ring support  

DOE Patents [OSTI]

Today, the trend is to increase the temperature of operation of gas turbine engines. To cool the components with compressor discharge air, robs air which could otherwise be used for combustion and creates a less efficient gas turbine engine. The present low thermal expansion sealing ring support system reduces the quantity of cooling air required while maintaining life and longevity of the components. Additionally, the low thermal expansion sealing ring reduces the clearance "C","C'" demanded between the interface between the sealing surface and the tip of the plurality of turbine blades. The sealing ring is supported by a plurality of support members in a manner in which the sealing ring and the plurality of support members independently expand and contract relative to each other and to other gas turbine engine components.

Dewis, David W. (San Diego, CA); Glezer, Boris (Del Mar, CA)

2000-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "aerosol-based duct sealing" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


161

Duct Systems in Large Commercial Buildings: Physical  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Duct Systems in Large Commercial Buildings: Physical Characterization, Air Leakage, and Heat Conduction Gains William 1. Fisk, Woody Delp, Rick Diamond, Darryl Dickerhoff, Ronnen Levinson, Mark Modera, Matty Nematollahi, Duo Wang Environmental Energy Technologies Division Indoor Environment Department Lawrence Berkeley National Laboratory Berkeley CA 94720 March 30, 1999 This work was supported by the Assistant Secretary for Energy Efficiency and Renewable Energy, Office of Building Technology and Community Systems, of the US Department of Energy under Contract No. DE-AC03-76SF00098 and by the California Institute For Energy Efficiency. LBNL-42339

162

New Seals - Vulnerability Assessment Team - Nuclear Engineering Division  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

More Information More Information VAT Projects Introducing the VAT Adversarial Vulnerability Assessments Safety Tags & Product Counterfeiting Election Security Spoofing GPS Defeating Existing Tamper-Indicating Seals Specialty Field Tools & Sampling Tools Insider Threat Mitigation Drug Testing Security Microprocessor Prototypes The Journal of Physical Security Vulnerability Assessments Vulnerability Assessments Insanely Fast µProcessor Shop Insanely Fast µProcessor Shop Seals About Seals Applications of Seals Common Myths about Tamper Indicating Seals Definitions Findings and Lessons Learned New Seals Types of Seals Seals References Selected VAT Papers Selected VAT Papers Selected Invited Talks Self-Assessment Survey Security Maxims Devil's Dictionary of Security Terms Argonne's VAT (brochure)

163

Findings and Lessons, Seals - Vulnerability Assessment Team - Nuclear  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Findings and Lessons Learned Findings and Lessons Learned VAT Projects Introducing the VAT Adversarial Vulnerability Assessments Safety Tags & Product Counterfeiting Election Security Spoofing GPS Defeating Existing Tamper-Indicating Seals Specialty Field Tools & Sampling Tools Insider Threat Mitigation Drug Testing Security Microprocessor Prototypes The Journal of Physical Security Vulnerability Assessments Vulnerability Assessments Insanely Fast µProcessor Shop Insanely Fast µProcessor Shop Seals About Seals Applications of Seals Common Myths about Tamper Indicating Seals Definitions Findings and Lessons Learned New Seals Types of Seals Seals References Selected VAT Papers Selected VAT Papers Selected Invited Talks Self-Assessment Survey Security Maxims Devil's Dictionary of Security Terms

164

Lightweight Sealed Steel Fuel Tanks for Advanced Hybrid Electric...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Sealed Steel Fuel Tanks for Advanced Hybrid Electric Vehicles Lightweight Sealed Steel Fuel Tanks for Advanced Hybrid Electric Vehicles 2012 DOE Hydrogen and Fuel Cells Program and...

165

Sealing glasses for titanium and titanium alloys  

DOE Patents [OSTI]

Barium lanthanoborate sealing-glass compositions are provided comprising various combinations (in terms of mole-%) of boron oxide (B.sub.2 O.sub.3), barium oxide (BaO), lanthanum oxide (La.sub.2 O.sub.3), and at least one other oxide selected from the group consisting of aluminum oxide (Al.sub.2 O.sub.3), calcium oxide (CaO), lithium oxide (Li.sub.2 O), sodium oxide (Na.sub.2 O), silicon dioxide (SiO.sub.2), or titanium dioxide (TiO.sub.2). These sealing-glass compositions are useful for forming hermetic glass-to-metal seals with titanium and titanium alloys having an improved aqueous durability and favorable sealing characteristics. Examples of the sealing-glass compositions are provided having coefficients of thermal expansion about that of titanium or titanium alloys, and with sealing temperatures less than about 900.degree. C., and generally about 700.degree.-800.degree. C. The barium lanthanoborate sealing-glass compositions are useful for components and devices requiring prolonged exposure to moisture or water, and for implanted biomedical devices (e.g. batteries, pacemakers, defibrillators, pumps).

Brow, Richard K. (Albuquerque, NM); McCollister, Howard L. (Albuquerque, NM); Phifer, Carol C. (Albuquerque, NM); Day, Delbert E. (Rolla, MO)

1997-01-01T23:59:59.000Z

166

Sealing glasses for titanium and titanium alloys  

DOE Patents [OSTI]

Barium lanthanoborate sealing-glass compositions are provided comprising various combinations (in terms of mole-%) of boron oxide (B{sub 2}O{sub 3}), barium oxide (BaO), lanthanum oxide (La{sub 2}O{sub 3}), and at least one other oxide selected from the group consisting of aluminum oxide (Al{sub 2}O{sub 3}), calcium oxide (CaO), lithium oxide (Li{sub 2}O), sodium oxide (Na{sub 2}O), silicon dioxide (SiO{sub 2}), or titanium dioxide (TiO{sub 2}). These sealing-glass compositions are useful for forming hermetic glass-to-metal seals with titanium and titanium alloys having an improved aqueous durability and favorable sealing characteristics. Examples of the sealing-glass compositions are provided having coefficients of thermal expansion about that of titanium or titanium alloys, and with sealing temperatures less than about 900 C, and generally about 700--800 C. The barium lanthanoborate sealing-glass compositions are useful for components and devices requiring prolonged exposure to moisture or water, and for implanted biomedical devices (e.g. batteries, pacemakers, defibrillators, pumps). 1 fig.

Brow, R.K.; McCollister, H.L.; Phifer, C.C.; Day, D.E.

1997-07-15T23:59:59.000Z

167

RATIONALE FOR MEASURING DUCT LEAKAGE FLOWS IN LARGE COMMERCIAL BUILDINGS  

E-Print Network [OSTI]

. Some duct sections operate at high static pressures (e.g., 100 to 2,500 Pa), but other sections leakage flows is to assume that an average duct static pressure applies to every leak. A third important2 ), central HVAC systems continuously supply heated or cooled air to conditioned spaces through

Diamond, Richard

168

Compression effects on pressure loss in flexible HVAC ducts  

SciTech Connect (OSTI)

A study was conducted to evaluate the effect of compression on pressure drop in flexible, spiral wire helix core ducts used in residential and light commercial applications. Ducts of 6 inches, 8 inches and 10 inches (150, 200 and 250 mm) nominal diameters were tested under different compression configurations following ASHRAE Standard 120-1999--Methods of Testing to Determine Flow Resistance of HVAC Air Ducts and Fittings. The results showed that the available published references tend to underestimate the effects of compression. The study demonstrated that moderate compression in flexible ducts, typical of that often seen in field installations, could increase the pressure drop by a factor of four, while further compression could increase the pressure drop by factors close to ten. The results proved that the pressure drop correction factor for compressed ducts cannot be independent of the duct size, as suggested by ASHRAE Fundamentals, and therefore a new relationship was developed for better quantification of the pressure drop in flexible ducts. This study also suggests potential improvements to ASHRAE Standard 120-1999 and provides new data for duct design.

Abushakra, Bass; Walker, Iain S.; Sherman, Max H.

2002-07-01T23:59:59.000Z

169

E-Print Network 3.0 - advanced bile duct Sample Search Results  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

the bile ducts, reabsorption in the ileum... inhibitors (9, 50). Bile duct ligated and LCA induced cholestasis animal models (8), and human cholestatic... Regulation of...

170

Duct injection technology prototype development: Nozzle development Subtask 4.1, Atomizer specifications for duct injection technology. Topical report 8  

SciTech Connect (OSTI)

Babcock & Wilcox has conducted a program to identify atomizers appropriate for successful in-duct injection of humidification water and lime slurries. The purpose of this program was to identify and quantify atomizer spray and performance criteria that affect the operations and reliability of the in-duct SO{sub 2} removal process, and compare commercially available atomizers to these criteria.

Not Available

1992-02-01T23:59:59.000Z

171

Air Sealing Your Home | Department of Energy  

Broader source: Energy.gov (indexed) [DOE]

Your Home Your Home Air Sealing Your Home November 26, 2013 - 6:22pm Addthis Save on heating and cooling costs by checking for air leaks in common trouble spots in your home. Save on heating and cooling costs by checking for air leaks in common trouble spots in your home. What does this mean for me? Save money and energy by air sealing your house. Caulking and weatherstripping are simple, effective ways of sealing air leaks in your home. Reducing the amount of air that leaks in and out of your home is a cost-effective way to cut heating and cooling costs, improve durability, increase comfort, and create a healthier indoor environment. Caulking and weatherstripping are two simple and effective air-sealing techniques that offer quick returns on investment, often one year or less. Caulk is

172

Rotatable seal assembly. [Patent application; rotating targets  

DOE Patents [OSTI]

An assembly is provided for rotatably supporting a rotor on a stator so that vacuum chambers in the rotor and stator remain in communication while the chambers are sealed from ambient air, which enables the use of a ball bearing or the like to support most of the weight of the rotor. The apparatus includes a seal device mounted on the rotor to rotate therewith, but shiftable in position on the rotor while being sealed to the rotor as by an O-ring. The seal device has a flat face that is biased towards a flat face on the stator, and pressurized air is pumped between the faces to prevent contact between them while spacing them a small distance apart to avoid the inflow of large amounts of air between the faces and into the vacuum chambers.

Logan, C.M.; Garibaldi, J.L.

1980-11-12T23:59:59.000Z

173

2011 Fur Seal Subsistence Harvest Report The Subsistence Harvest of Northern Fur Seals  

E-Print Network [OSTI]

.................................................................................................................... 6 By-products and Waste.............................. 6 Heat Strokes seals harvested b) incidence of by-products and waste during the harvest process c) the occurrence

174

Rapid Sampling from Sealed Containers - Vulnerability Assessment Team -  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Nonproliferation and Nonproliferation and National Security > VAT > Current Projects > Rapid Sampling Tools > ... from Sealed Containers VAT Projects Introducing the VAT Adversarial Vulnerability Assessments Safety Tags & Product Counterfeiting Election Security Spoofing GPS Defeating Existing Tamper-Indicating Seals Specialty Field Tools & Sampling Tools Tamper & Intrusion Detection Rapid Sampling from Sealed Containers Demo video Insider Threat Mitigation Drug Testing Security Microprocessor Prototypes The Journal of Physical Security Vulnerability Assessments Vulnerability Assessments Insanely Fast µProcessor Shop Insanely Fast µProcessor Shop Seals About Seals Applications of Seals Common Myths about Tamper Indicating Seals Definitions Findings and Lessons Learned

175

Notes 11. High pressure floating ring seals  

E-Print Network [OSTI]

turbines and compressors, squeeze film dampers aid to attenuate rotor vibrations and provide mechanical isolation. Feed groove oil inlet seal ?? housing ournal lubricant film shaft nti-rotation pin ball bearing Discharge groove... turbines and compressors, squeeze film dampers aid to attenuate rotor vibrations and provide mechanical isolation. Feed groove oil inlet seal ?? housing ournal lubricant film shaft nti-rotation pin ball bearing Discharge groove...

San Andres, Luis

2009-01-01T23:59:59.000Z

176

Sealed fiber-optic bundle feedthrough  

DOE Patents [OSTI]

A sealed fiber-optic bundle feedthrough by which a multitude of fiber-optic elements may be passed through an opening or port in a wall or structure separating two environments at different pressures or temperatures while maintaining the desired pressure or temperature in each environment. The feedthrough comprises a rigid sleeve of suitable material, a bundle of individual optical fibers, and a resin-based sealing material that bonds the individual optical fibers to each other and to the rigid sleeve.

Tanner, Carol E. (Niles, MI)

2002-01-01T23:59:59.000Z

177

Emergency sacrificial sealing method in filters, equipment, or systems  

DOE Patents [OSTI]

A system seals a filter or equipment component to a base and will continue to seal the filter or equipment component to the base in the event of hot air or fire. The system includes a first sealing material between the filter or equipment component and the base; and a second sealing material between the filter or equipment component and the base and proximate the first sealing material. The first sealing material and the second seal material are positioned relative to each other and relative to the filter or equipment component and the base to seal the filter or equipment component to the base and upon the event of fire the second sealing material will be activated and expand to continue to seal the filter or equipment component to the base in the event of hot air or fire.

Brown, Erik P

2014-09-30T23:59:59.000Z

178

The Yucca Mountain Project repository sealing program  

SciTech Connect (OSTI)

Yucca Mountain is being characterized for the development of a high-level nuclear waste repository. The repository is planned to be located in the unsaturated zone in fractured, welded tuff. Sealing of the repository is one element of the Yucca Mountain Project. This paper presents a description of the current sealing design options, design requirements, and the design constraints. Design options for the shafts include anchor-to-bedrock seals, shaft fill, and settlement plugs; in the underground facility, they include drift seals, drainage channels, sumps, and bulkheads. Design requirements are those quantitative requirements imposed on the sealing design options to achieve a desired level of performance. For example, a design requirement could be a restriction on the hydraulic conductivity of a design option. Constraints are restrictions placed on the repository design by the sealing design. An example of a constraint could be establishing the drainage pattern to direct flow from emplacement drifts to nonemplacement drifts. As (1) additional hydrogeologic data are obtained through site characterization, (2) approaches to allocating performance to various subsystems within the Yucca Mountain Project are refined, and (3) the exploratory shafts and the associated testing results are developed, the design requirements and constraints may be modified and used in developing the License Application Design.

Fernandez, J.A.; Hinkebein, T.E

1989-12-01T23:59:59.000Z

179

Development of a new duct leakage test: DeltaQ  

SciTech Connect (OSTI)

Duct leakage is a key factor in determining energy losses from forced air heating and cooling systems. Several studies (Francisco and Palmiter 1997 and 1999, Andrews et al. 1998, and Siegel et al. 2001) have shown that the duct system efficiency cannot be reliably determined without good estimates of duct leakage. Specifically, for energy calculations, it is the duct leakage air flow to outside at operating conditions that is required. Existing test methods either precisely measure the size of leaks (but not the flow through them at operating conditions), or measure these flows with insufficient accuracy. The DeltaQ duct leakage test method was developed to provide improved estimates of duct leakage during system operation. In this study we developed the analytical calculation methods and the test procedures used in the DeltaQ test. As part of the development process, we have estimated uncertainties in the test method (both analytically and based on field data) and designed automated test procedures to increase accuracy and reduce the contributions of operator errors in performing field tests. In addition, the test has been evaluated in over 100 houses by several research teams to show that it can be used in a wide range of houses and to aid in finding limits or problems in field applications. The test procedure is currently being considered by ASTM as an update of an existing duct leakage standard.

Walker,I.S.; Sherman,M.H.; Wempen, J.; Wang, D.; McWilliams, J.A.; Dickerhoff, D.J.

2001-08-01T23:59:59.000Z

180

Performance and reliability enhancement of turbo-pump labyrinth seals  

E-Print Network [OSTI]

Radial velocity distribution within an idealized original IP Seal cavity. 28 Pressure relative to cavity inlet value within an idealized original IP Seal cavity. Turbulence energy distribution within an 4. 4(a) 4. 4(b) 4. 5(a) 4. 5(b) 4, 6(B) 4... cavity. Radial velocity distribution within Seal 17 cavity Radial velocity distribution within Seal 2 cavity. . . 30 IP Seal cavity. . . . 31 33 34 . . 36 . . 37 . . 38 , , 39 . . 40 . . 41 . . 42 xs Figure 4. 9(a) Pressure relative...

Guidry, Michael James

1991-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "aerosol-based duct sealing" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


181

Duct Leakage Impacts on VAV System Performance in Large Commercial  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Duct Leakage Impacts on VAV System Performance in Large Commercial Duct Leakage Impacts on VAV System Performance in Large Commercial Buildings Title Duct Leakage Impacts on VAV System Performance in Large Commercial Buildings Publication Type Report LBNL Report Number LBNL-53605 Year of Publication 2003 Authors Wray, Craig P., and Nance Matson Abstract The purpose of this study is to evaluate the variability of duct leakage impacts on air distribution system performance for typical large commercial buildings in California. Specifically, a hybrid DOE-2/TRNSYS sequential simulation approach was used to model the energy use of a low-pressure terminal-reheat variable-air-volume (VAV) HVAC system with six duct leakage configurations (tight to leaky) in nine prototypical large office buildings (representing three construction eras in three California climates where these types of buildings are common). Combined fan power for the variable-speed-controlled supply and return fans at design conditions was assumed to be 0.8 W/cfm. The VAV system that we simulated had perfectly insulated ducts, and maintained constant static pressure in the ducts upstream of the VAV boxes and a constant supply air temperature at the air-handler. Further evaluations of duct leakage impacts should be carried out in the future after methodologies are developed to deal with duct surface heat transfer effects, to deal with airflows entering VAV boxes from ceiling return plenums (e.g., to model parallel fan-powered VAV boxes), and to deal with static pressure reset and supply air temperature reset strategies.

182

Development of a New Duct leakage Test: Delta Q  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Development of a New Duct leakage Test: Delta Q Development of a New Duct leakage Test: Delta Q Title Development of a New Duct leakage Test: Delta Q Publication Type Report LBNL Report Number LBNL-47308 Year of Publication 2001 Authors Walker, Iain S., Max H. Sherman, J. Wempen, Duo Wang, Jennifer A. McWilliams, and Darryl J. Dickerhoff Abstract Several studies (Francisco and Palmiter 1997 and 1999, Andrews et al. 1998, and Siegel et al. 2001) have shown that the duct system efficiency cannot be reliably determined without good estimates of duct leakage. Specifically, for energy calculations, it is the duct leakage air flow to outside at operating conditions that is required. Existing test methods either precisely measure the size of leaks (but not the flow through them at operating conditions), or measure these flows with insufficient accuracy. The DeltaQ duct leakage test method was developed to provide improved estimates of duct leakage during system operation. In this study we developed the analytical calculation methods and the test procedures used in the DeltaQ test. As part of the development process, we have estimated uncertainties in the test method (both analytically and based on field data) and designed automated test procedures to increase accuracy and reduce the contributions of operator errors in performing field tests. In addition, the test has been evaluated in over 100 houses by several research teams to show that it can be used in a wide range of houses and to aid in finding limits or problems in field applications. The test procedure is currently being considered by ASTM as an update of an existing duct leakage standard

183

Evaluation of friction loss in flexible and galvanized duct  

E-Print Network [OSTI]

for Friction Loss in Straight Runs of Duct (a'Ipha=0. 10). 21 Ill Static Pressure Data Converted to Equivalent Lengths. 23 IV Duncan's Multiple Range Test of Variability for Equivalent Lengths of 90 Degree Elbows (al pha=0. IO). 26 V Student t Test... because of the higher Friction losses obtained in the first 1. 5 hours of testing. The Investigators concluded that when flex'ible duct was properly installed the Friction losses compared reasonably well with the friction losses in galvanized duct. i...

Zimmermann, Carlos Michael Alberto

2012-06-07T23:59:59.000Z

184

Sensitivity of forced air distribution system efficiency to climate, duct location, air leakage and insulation  

E-Print Network [OSTI]

Location, Air Leakage and Insulation Iain S. Walker Energy4 Duct Insulation, Location and Leakageinsulation

Walker, Iain

2001-01-01T23:59:59.000Z

185

Leakage and rotordynamic effects of pocket damper seals and see-through labyrinth seals  

E-Print Network [OSTI]

and PDS with two to six blades. Leakage and pressure measurements were made with air as the working fluid on twenty-two seal configurations. Increasing seal blade thickness reduced leakage by the largest amount. Blade profile results were more equivocal...

Gamal Eldin, Ahmed Mohamed

2009-05-15T23:59:59.000Z

186

Leakage and rotordynamic effects of pocket damper seals and see-through labyrinth seals  

E-Print Network [OSTI]

and PDS with two to six blades. Leakage and pressure measurements were made with air as the working fluid on twenty-two seal configurations. Increasing seal blade thickness reduced leakage by the largest amount. Blade profile results were more equivocal...

Gamal Eldin, Ahmed Mohamed

2008-10-10T23:59:59.000Z

187

Improving Building Envelope and Duct Airtightness of US Dwellings The  

E-Print Network [OSTI]

the building envelope and duct system airtightness of US single-family detached homes, manufactured homes, and multi-family homes, before and after energy retrofits. These data are part of the Residential Improving Building Envelope

188

DOE Zero Energy Ready Home Webinar: Ducts in Conditioned Space  

Broader source: Energy.gov [DOE]

DOE Challenge Home is a blueprint for zero energy ready homes. When we make that statement its impossible to justify huge thermal losses from ducts in unconditioned spaces. Thats why one of...

189

DOE Zero Energy Ready Home Webinar: Ducts in Conditioned Space...  

Broader source: Energy.gov (indexed) [DOE]

America research program its and partners have worked out the kinks on a toolkit of duct design strategies. In this session you'll learn the pros and cons of these strategies so...

190

Clutter-Based Evaporation Duct Estimation Performance Using Meteorological Statistics  

E-Print Network [OSTI]

of California, Mediterranean, Persian Gulf, and Coast of Brazil. The effects of the radar frequency (S, C, and X, such as the Mediterranean, Persian Gulf, East China Sea, and California Coast, atmospheric ducts are common occurrences

Gerstoft, Peter

191

Economizer Applications in Dual-Duct Air-Handling Units  

E-Print Network [OSTI]

This paper provides analytical tools and engineering methods to evaluate the feasibility of the economizer for dual-duct air-handling units. The results show that the economizer decreases cooling energy consumption without heating energy penalties...

Joo, I.; Liu, M.

2002-01-01T23:59:59.000Z

192

Solid oxide fuel cell having a glass composite seal  

DOE Patents [OSTI]

A solid oxide fuel cell stack having a plurality of cassettes and a glass composite seal disposed between the sealing surfaces of adjacent cassettes, thereby joining the cassettes and providing a hermetic seal therebetween. The glass composite seal includes an alkaline earth aluminosilicate (AEAS) glass disposed about a viscous glass such that the AEAS glass retains the viscous glass in a predetermined position between the first and second sealing surfaces. The AEAS glass provides geometric stability to the glass composite seal to maintain the proper distance between the adjacent cassettes while the viscous glass provides for a compliant and self-healing seal. The glass composite seal may include fibers, powders, and/or beads of zirconium oxide, aluminum oxide, yttria-stabilized zirconia (YSZ), or mixtures thereof, to enhance the desirable properties of the glass composite seal.

De Rose, Anthony J.; Mukerjee, Subhasish; Haltiner, Jr., Karl Jacob

2013-04-16T23:59:59.000Z

193

Mechanical seal having a single-piece, perforated mating ring  

DOE Patents [OSTI]

A mechanical seal (e.g., single mechanical seals, double mechanical seals, tandem mechanical seals, bellows, pusher mechanical seals, and all types of rotating and reciprocating machines) with reduced contact surface temperature, reduced contact surface wear, or increased life span. The mechanical seal comprises a rotating ring and a single-piece, perforated mating ring, which improves heat transfer by controllably channeling coolant flow through the single-piece mating ring such that the coolant is in substantially uniform thermal contact with a substantial portion of the interior surface area of the seal face, while maintaining the structural integrity of the mechanical seal and minimizing the potential for coolant flow interruptions to the seal face caused by debris or contaminants (e.g., small solids and trash) in the coolant.

Khonsari, Michael M. (Baton Rouge, LA); Somanchi, Anoop K. (Fremont, CA)

2007-08-07T23:59:59.000Z

194

Tags and seals for arms control verification  

SciTech Connect (OSTI)

Tags and seals have long been recognized as important tools in arms control. The trend in control of armaments is to limit militarily significant equipment that is capable of being verified through direct and cooperative means, chiefly on-site inspection or monitoring. Although this paper will focus on the CFE treaty, the role of tags and seals for other treaties will also be addressed. Published technology and concepts will be reviewed, based on open sources. Arms control verification tags are defined as unique identifiers designed to be tamper-revealing; in that respect, seals are similar, being used as indicators of unauthorized access. Tamper-revealing tags might be considered as single-point markers, seals as two-point couplings, and nets as volume containment. The functions of an arms control tag can be considered to be two-fold: to provide field verification of the identity of a treaty-limited item (TLI), and to have a means of authentication of the tag and its tamper-revealing features. Authentication could take place in the field or be completed elsewhere. For CFE, the goal of tags and seals can be to reduce the overall cost of the entire verification system.

DeVolpi, A.

1990-09-18T23:59:59.000Z

195

BETTER DUCT SYSTEMS FOR HOME HEATING AND COOLING.  

SciTech Connect (OSTI)

This is a series of six guides intended to provide a working knowledge of residential heating and cooling duct systems, an understanding of the major issues concerning efficiency, comfort, health, and safety, and practical tips on installation and repair of duct systems. These guides are intended for use by contractors, system designers, advanced technicians, and other HVAC professionals. The first two guides are also intended to be accessible to the general reader.

ANDREWS,J.

2001-01-01T23:59:59.000Z

196

Impact of El Nino on the foraging behavior of female northern elephant seals  

E-Print Network [OSTI]

diving behavior of northern elephant seals. J Exp Biol 201:behavior of female northern elephant seals Daniel E. Crockerbehavior of northern elephant seals Mirounga angustirostris

Crocker, D E; Costa, Daniel P; Le Boeuf, B J; Webb, P M; Houser, D S

2006-01-01T23:59:59.000Z

197

REGULATION OF LIPID METABOLISM AND MILK LIPID CONTENT IN NORTHERN ELEPHANT SEALS  

E-Print Network [OSTI]

and late molting adult female northern elephant seals (n=production in fasting elephant seals. Insulin differentially95 Figure 3. 3: Elephant seal blubber ATGL activity at

Fowler, Melinda Anne

2012-01-01T23:59:59.000Z

198

Wide and multiple apex seals for the rotary engine: (Abbr.: Multi-Apex-Seals for the Rotary Engine)  

Science Journals Connector (OSTI)

Abstract Conventional rotary engines are based on a trochoidal-type housing bore profile and its inside envelope is the basis of the rotor profile. To seal the chambers, spring-loaded apex seals are used in place of the designed rotor apexes. The conventional design method is limited to an epitrochoidal-based housing and does not consider the apex seal profile. Previously the authors presented the complete theory and algorithm of the deviation-function (DF) method of rotary engine design based on the apex seal profile. By using the DF method, the apex seal and engine housing bore are conjugate kinematic pairs, which enable the design of a variety of apex seals that conform to the bore, including wider apex seals and multiple seals at each rotor apex. The wide apex seal design has better rotor-to-housing conformity and therefore improves sealing. The multi-apex-seal grid assembly improves sealing capability and also reduces the forces on the apex seals. The incorporation of apex seal profiles into the rotary engine design process also makes possible a larger variety of new rotary engine profiles.

Sarah Warren Rose; Daniel C.H. Yang

2014-01-01T23:59:59.000Z

199

Seal assembly with anti-rotation pin for high pressure supercritical fluids  

DOE Patents [OSTI]

A seal assembly for sealing a machine with a first chamber and a second chamber is provided. A rotating shaft extends through the first and second chambers, and rotates therein. The seal assembly has a seal housing, a seal ring and a seal pin. The seal housing is positionable in the machine housing. The seal housing has a seal pocket extending into a fluid side thereof, and a housing receptacle extending into an inner diameter thereof at the seal pocket. The seal ring is positionable in the seal pocket of the seal housing for forming a seal therewith. The seal ring has a ring receptacle extending into an outer diameter thereof. The ring receptacle is positionable adjacent to the housing receptacle for defining a pin hole therebetween. The seal pin is loosely positionable in the pin hole whereby movement about the seal ring is accommodated while preventing rotation thereof.

Wright, Steven A.; Fuller, Robert L.

2014-08-05T23:59:59.000Z

200

Solar collector construction and sealing arrangement  

SciTech Connect (OSTI)

A sealing arrangement is disclosed by which a glass panel cover may be installed with a weather-tight seal in a solar collector housing. The housing includes side walls, the upper edges of which are formed with a generally cylindrical groove which faces upwardly. The sealing arrangement includes an elongate resilient body formed with a generally cylindrical anchor section having a cross-section of a dimension just the same as or less than the cross-section dimension of the cylindrical groove, and a holding section formed integrally with the anchor section near the top thereof and having a generally U-shaped cross-section which faces inwardly of the housing.

Leflar, J.A.; Wardlow, W.C.

1985-02-12T23:59:59.000Z

Note: This page contains sample records for the topic "aerosol-based duct sealing" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


201

SECA Core Technology Program Seal Workshop  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

SECA Core Technology Program Seal Workshop Workshop held at Hyatt Regency, San Antonio August 10, 2007 Workshop organized by: Dr. Ayyakkannu Manivannan, National Energy technology Laboratory Morgantown, WV Dr. Prabhakar Singh Pacific Northwest National Laboratory Richland, WA 1 2 Table of Content * Executive Summary * Meeting Agenda * Presentations * List of Attendees 3 Executive Summary SECA Core Technology Program (SECA CTP) led workshop on the topical area titled "SOFC seal: Technology, Challenges and Future Directions" was held on August 10, 2007 at Hyatt Regency, San Antonio, TX. The workshop was attended by scientists and engineers presently involved in the development, engineering, fabrication, and testing of

202

Gas Seal Leakage at High Temperature: A Labyrinth Seal and an All-Metal Complaint Seal of Similar Clearance  

E-Print Network [OSTI]

/5 the flow of a labyrinth seal for pressure ratios (Ps/Pa) > 3.5. The savings in leakage are maximized during operation at high pressure differentials. Leakage measurements with a rotor spinning to a maximum speed of 2,700 rpm (surface speed = 23.6 m...

Anderson, Alain

2013-07-31T23:59:59.000Z

203

High Temperature Leakage Performance of a Hybrid Brush Seal Compared to a Standard Brush Seal and a Labyrinth Seal  

E-Print Network [OSTI]

design that adds to the bristle brush matrix a number of cantilever pads that rest on the rotor surface. Upon shaft rotation the pads lift due to the generation of a hydrodynamic gas film while the brushes effectively seal an upstream pressure. Hence...

Ashton, Zachary

2010-01-14T23:59:59.000Z

204

Experiment Hazard Class 8.2 - Sealed Sources  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

2 -Sealed Sources 2 -Sealed Sources Applicability This hazard classification applies to all experiments involving the use of DOE exempt and non-exempt radioactive sealed sources. Experiment Category Experiments in this Experiment Hazard Class are always categorized as low risk experiments. Experiment Hazard Control Verification Statements Engineered Controls - None. Procedural Controls - Sealed sources must be secured when no experimenter is present. Design Reviews and Equipment Inspections - Sealed sources must be checked out from the Beamline Sealed Source Custodian and logged into the RMS System. Sources will be exempt or non-exempt as determined by RSO-HP personnel. Training - GERT (ESH 738) for exempt sealed sources ANL Radiation Worker I or II (ESH 700 or ESH 702) for non-exempt sealed

205

Water Sealing of Detached Aluminium Oxide Anodic Film  

Science Journals Connector (OSTI)

... , including those sealed after removal from the aluminium. The patterns were compared with standard ASTM X-ray data and with results given by others5'6. A steam-sealed (115 ...

ROY C. SPOONER

1956-11-17T23:59:59.000Z

206

The effect of a new damper seal on rotordynamics  

E-Print Network [OSTI]

. Rap tests illustrate that the damping advantage of the gas damper seal increases with inlet air pressure and becomes overwhelming at inlet pressure above 40 psia. Experimental results show that the leakage rate of the tested gas damper seal...

Li, Qiming

2012-06-07T23:59:59.000Z

207

Flow visualization and leakage measurements of worn labyrinth seals  

E-Print Network [OSTI]

A large-scale flow visualization test facility is used to conduct an experimental investigation into the leakage resistance and flow characteristics of worn labyrinth seals. Wear in labyrinth seals is a consequence of contact between the rotating...

Allen, Brian Frank

1997-01-01T23:59:59.000Z

208

Fiberglass Duct Cleaning Safe Work Practices Duct Cleaning -Prior to reaching a decision to clean a duct, an investigation of possible  

E-Print Network [OSTI]

practices for cleaning ducts: · Contact vacuum - Uses a portable vacuum with a HEPA filter. Direct contact filter (HEPA) vacuum or use vacuum equipment that exhausts particles safely outside of the building-insulating any access holes that were made or used so they are airtight. 7. All components of the HVAC system

de Lijser, Peter

209

Measure Guideline: Guide to Attic Air Sealing  

SciTech Connect (OSTI)

The Guide to Attic Air Sealing was completed in 2010 and although not in the standard Measure Guideline format, is intended to be a Measure Guideline on Attic Air Sealing. The guide was reviewed during two industry stakeholders meetings held on December 18th, 2009 and January 15th, 2010, and modified based on the comments received. Please do not make comments on the Building America format of this document. The purpose of the Guide to Attic Air Sealing is to provide information and recommendations for the preparation work necessary prior to adding attic insulation. Even though the purpose of this guide is to save energy - health, safety and durability should not be compromised by energy efficiency. Accordingly, combustion safety and ventilation for indoor air quality are addressed first. Durability and attic ventilation then follow. Finally, to maximize energy savings, air sealing is completed prior to insulating. The guide is intended for home remodelers, builders, insulation contractors, mechanical contractors, general contractors who have previously done remodeling and homeowners as a guide to the work that needs to be done.

Lstiburek, J.

2014-09-01T23:59:59.000Z

210

Investigation of stepped labyrinth seal leakage performance  

E-Print Network [OSTI]

performance. Experimental tests were conducted using two test rigs. one of these test rigs was a 100:1 scale and the other was a 4:1 scale of an actual labyrinth seal. Both test rigs operated based on a two-dimensional planar flow concept. Tests were...

Reed, Thomas Stanley

2012-06-07T23:59:59.000Z

211

Positive contact, self retaining bearing seals  

DOE Patents [OSTI]

An ultra-low friction bearing including an inner race, an outer race, bearing elements engaged between the inner and outer races and a seal between the inner and outer races is disclosed. The seal includes first and second sealing washers. The first washer has an outer diameter greater than an inner diameter of the outer race and an inner diameter greater than the outer diameter of the inner race. The second washer has an inner diameter less than the outer diameter of the inner race and an outer diameter less than the inner diameter of the outer race. The first washer slidably engages the outer race, the second washer slidably engages the inner race and the washers overlap and slidably engage one another. One of the washers snap fits into its respective inner or outer race while the other washer engages a stepped surface of the other of the inner and outer races. The grooved and stepped surface are offset from one another in a longitudinal direction of the races such that the washers are conically loaded thus providing a seal between the inner and outer races sufficient to prevent lubricant and contaminating particles from passing therethrough. The washers are made from a non-metallic semi-flexible low-modulus material.

Johnson, Bruce H. (Kansas City, MO); Larsen, Lawrence E. (Kansas City, MO); Welch, Edmund F. (Kansas City, MO)

1992-05-05T23:59:59.000Z

212

Dynamic Cryogenic Seals to Support Fueling of Fusion Tokomaks  

E-Print Network [OSTI]

Dynamic Cryogenic Seals to Support Fueling of Fusion Tokomaks U. Naranjo and J. W. Leachman School in damaged products every year. Sealing at cryogenic temperatures is a substantially more difficult task than extruder in development at the WSU HYPER laboratory. The purpose of a cryogenic dynamic polymer seal

Collins, Gary S.

213

Counts of northern elephant seals, Mirounga angustirostris, from  

E-Print Network [OSTI]

176 Counts of northern elephant seals, Mirounga angustirostris, from large-format aerial northern elephant seals, Mirounga angustirostris, at rooker- ies in the United States and Mexico elephant seals (Bar- tholomew and Boolootian, 1960; Carlisle andAplin, 1966, 1971; Odell, 1971;Antonelis et

214

(ENFORCEMENT AGENCY CAN CUSTOMIZE WITH LETTERHEAD/SEAL)  

E-Print Network [OSTI]

(ENFORCEMENT AGENCY CAN CUSTOMIZE WITH LETTERHEAD/SEAL) 2008 Building Energy Efficiency Standards). 2. Central air conditioners & heat pumps less than 65,000 Btu/hr must have a minimum 13 SEER. 3 system must be sealed. · Only UL 181, UL 181A, or UL 181B approved tapes or mastic shall be used to seal

215

Measure Guideline: Optimizing the Configuration of Flexible Duct Junction Boxes  

SciTech Connect (OSTI)

This measure guideline offers additional recommendations to heating, ventilation, and air conditioning (HVAC) system designers for optimizing flexible duct, constant-volume HVAC systems using junction boxes within Air Conditioning Contractors of America (ACCA) Manual D guidance (Rutkowski, H. Manual D -- Residential Duct Systems, 3rd edition, Version 1.00. Arlington, VA: Air Conditioning Contractors of America, 2009.). IBACOS used computational fluid dynamics software to explore and develop guidance to better control the airflow effects of factors that may impact pressure losses within junction boxes among various design configurations (Beach, R., Prahl, D., and Lange, R. CFD Analysis of Flexible Duct Junction Box Design. Golden, CO: National Renewable Energy Laboratory, submitted for publication 2013). These recommendations can help to ensure that a system aligns more closely with the design and the occupants' comfort expectations. Specifically, the recommendations described herein show how to configure a rectangular box with four outlets, a triangular box with three outlets, metal wyes with two outlets, and multiple configurations for more than four outlets. Designers of HVAC systems, contractors who are fabricating junction boxes on site, and anyone using the ACCA Manual D process for sizing duct runs will find this measure guideline invaluable for more accurately minimizing pressure losses when using junction boxes with flexible ducts.

Beach, R.; Burdick, A.

2014-03-01T23:59:59.000Z

216

Duct Chase Sprinkler Replacement Project (4594), 5/31/2012  

Broader source: Energy.gov (indexed) [DOE]

Duct Chase Sprinkler Replacement Project (4594) Duct Chase Sprinkler Replacement Project (4594) Program or Field Office: Y-12 Site Office Location(s) (Citv/County/State): Oak Ridge, Anderson County, Tennessee Proposed Action Description: The proposed action is provide replacement of corroded and aged sprinkler heads in the plenum duct chases. Categorical Exclusion(s) Applied: 81.3- Routine maintenance Submit by E-mail For the complete DOE National Environmental Policy Act regulations regarding categorical exclusions, including the full text of each categorical exclusion, see Subpart D of I 0 CFR Part 1021. Regulatory Requirements in 10 CFR 1021.410(b): (See full text in regulation) [{Jrhe proposal fits within a class of actions that is listed in Appendix A orB to 10 CFR Part 1021, Subpart D.

217

Our Dog Discovered Our Ducts Have Cats | Department of Energy  

Broader source: Energy.gov (indexed) [DOE]

Our Dog Discovered Our Ducts Have Cats Our Dog Discovered Our Ducts Have Cats Our Dog Discovered Our Ducts Have Cats January 18, 2010 - 7:30am Addthis Amy Foster Parish Our Australian Shepherd, Matilda, is not the fiercest of protectors. In fact, she's a total coward. She flees in horror from strangers and is terrorized by the vacuum cleaner; even a pair of shoes left in an unaccustomed place can strike fear in her heart. But let her see a cat in the back yard, or even catch the scent of one on a walk, and my cowardly Matilda becomes a superhero ready to save me from the feline menace. So when Matilda started pulling her superhero routine in the house a few weeks ago, running from room to room and growling at the air registers in the floor, I was immediately suspicious. We don't own a cat, and Matilda's

218

DOE Zero Energy Ready Home Ducts in Conditioned Space Webinar...  

Broader source: Energy.gov (indexed) [DOE]

is typically -- in a typical house we've got the insulation, the thermal barrier, the air seal barrier, at the ceiling plane. What we're doing here is we're removing the...

219

Bundle duct interaction studies for fuel assemblies. [LMFBR  

SciTech Connect (OSTI)

It is known that the wire-wrapped rods and duct in an LMFBR are undergoing a gradual structural distortion from the initially uniform geometry under the combined effects of thermal expansion and irradiation induced swelling and creep. These deformations have a significant effect on flow characteristics, thus causing changes in thermal behavior such as cladding temperature and temperature distribution within a bundle. The temperature distribution may further enhance or retard irradiation induced deformation of the bundle. This report summarizes the results of the continuing effort in investigating the bundle-duct interaction, focusing on the need for the large development plant.

Hsia, H.T.S.; Kaplan, S.

1981-06-01T23:59:59.000Z

220

Advanced Strategy Guideline: Air Distribution Basics and Duct Design  

SciTech Connect (OSTI)

This report discusses considerations for designing an air distribution system for an energy efficient house that requires less air volume to condition the space. Considering the HVAC system early in the design process will allow adequate space for equipment and ductwork and can result in cost savings. Principles discussed that will maximize occupant comfort include delivery of the proper amount of conditioned air for appropriate temperature mixing and uniformity without drafts, minimization of system noise, the impacts of pressure loss, efficient return air duct design, and supply air outlet placement, as well as duct layout, materials, and sizing.

Burdick, A.

2011-12-01T23:59:59.000Z

Note: This page contains sample records for the topic "aerosol-based duct sealing" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


221

Integration of HVAC System Design with Simplified Duct Distribution- Building America Top Innovation  

Broader source: Energy.gov [DOE]

This Building America Innovations profile describes work by Building America research teams who field tested simplified duct designs in hundreds of homes, confirming the performance of short compact duct runs, with supply registers near interior walls.

222

Sensitivity of Forced Air Distribution System Efficiency to Climate, Duct Location, Air Leakage and Insulation  

E-Print Network [OSTI]

. 94720 This work was supported by the Assistant Secretary for Energy Efficiency and Renewable Energy......................................................... 5 Figure 4. New plastic flexible ducts in an attic.......................................................................... 6 Figure 5. Combination of plastic insulated flexible duct and added open face glass fiber

223

Variable Speed Drive (VSD) Applications in Dual-Duct Constant Volume Systems  

E-Print Network [OSTI]

Models have been developed for static pressure and potential supply fan energy savings by using variable speed drive (VSD) in dual-duct constant volume systems. Experiments have been performed using a full size dual-duct constant volume system...

Joo, I.; Liu, M.; Conger, K.; Wang, G.

2002-01-01T23:59:59.000Z

224

Study advances view of geopressure seals  

SciTech Connect (OSTI)

The last decade has seen a growing interest in the subject of fluid pressure seals and fluid flow in hydrocarbon-bearing basins. As explorationists begin to view basins in terms of coupled, dynamic, chemical, and physical processes, seemingly unrelated observations become interrelated. It is precisely the integration of geological, geochemical, and geophysical observations that opens the door for new exploration opportunities. This article lays a conceptual foundation in the area of geopressure seals and on the role of geopressure in hydrocarbon migration and accumulation in young, clastic basins. The exploration significance of geopressure can be appreciated when one considers that within the gulf Coast basin, geopressured fields, which represent only 10% of the total number of fields, account for approximately 50% of the cumulative production.

Benzing, W.M.; Shook, G.M. [Idaho National Engineering Lab., Idaho Falls, ID (United States)

1996-05-20T23:59:59.000Z

225

Spent Sealed Sources Management in Switzerland - 12011  

SciTech Connect (OSTI)

Information is provided about the international recommendations for the safe management of disused and spent sealed radioactive sources wherein the return to the supplier or manufacturer is encouraged for large radioactive sources. The legal situation in Switzerland is described mentioning the demand of minimization of radioactive waste as well as the situation with respect to the interim storage facility at the Paul Scherrer Institute (PSI). Based on this information and on the market situation with a shortage of some medical radionuclides the management of spent sealed sources is provided. The sources are sorted according to their activity in relation to the nuclide-specific A2-value and either recycled as in the case of high active sources or conditioned as in the case for sources with lower activity. The results are presented as comparison between recycled and conditioned activity for three selected nuclides, i.e. Cs-137, Co-60 and Am-241. (author)

Beer, H.F. [Paul Scherrer Institute, CH-5232 Villigen (Switzerland)

2012-07-01T23:59:59.000Z

226

Statistical maritime radar duct estimation using hybrid genetic algorithm-Markov chain Monte Carlo method  

E-Print Network [OSTI]

radar ducts over the Persian gulf, Journal of Appliedas the Mediter- ranean, Persian Gulf, East China Sea, and

Yardim, Caglar; Gerstoft, Peter; Hodgkiss, William S.

2007-01-01T23:59:59.000Z

227

Duct Systems in large commercial buildings: Physical characterization, air leakage, and heat conduction gains  

E-Print Network [OSTI]

connected to a variable frequency drive. + Static pressureSpeed as Frequency of Variable-speed Drive (hz) All Ducts ~

Fisk, W.J.

2011-01-01T23:59:59.000Z

228

High expansion, lithium corrosion resistant sealing glasses  

DOE Patents [OSTI]

Glass compositions containing CaO, Al.sub.2 O.sub.3, B.sub.2 O.sub.3, SrO and BaO in various combinations of mole % are provided. These compositions are capable of forming stable glass-to-metal seals with pin materials of 446 Stainless Steel and Alloy-52 rather than molybdenum, for use in harsh chemical environments, specifically in lithium batteries.

Brow, Richard K. (Albuquerque, NM); Watkins, Randall D. (Albuquerque, NM)

1991-01-01T23:59:59.000Z

229

Theoretical Estimates of HVAC Duct Channel Capacity for High-Speed Internet Access  

E-Print Network [OSTI]

Theoretical Estimates of HVAC Duct Channel Capacity for High-Speed Internet Access Ariton E. Xhafa-conditioning (HVAC) ducts based on multi-carrier transmission that uses M-QAM mod- ulation and measured channel- flections in HVAC ducts). Our work also shows that data rates in excess of 300 Mbps are possible over

Stancil, Daniel D.

230

RF propagation in an HVAC duct system: impulse response characteristics of the channel  

E-Print Network [OSTI]

RF propagation in an HVAC duct system: impulse response characteristics of the channel Pavel V, the heating, ventilation, and air conditioning (HVAC) duct system in buildings is a complex network of hollow at RF and microwave frequencies of com- mon interest. HVAC ducts can be used as a wireless communication

Stancil, Daniel D.

231

Static Pressure Losses in 6, 8, and 10-inch Non-Metallic Flexible Ducts  

E-Print Network [OSTI]

This study measured airflow static pressure losses through non-metallic flexible ducts in compliance with ASHRAE Standard 120-1999, Methods of Testing to Determine Flow Resistance of HVAC Air Ducts and Fittings (ASHRAE 1999). Duct sizes of 6, 8...

Weaver, K.; Culp, C.

2006-01-01T23:59:59.000Z

232

Improving Control of a Dual-Duct Single-Fan Variable Air Volume Systems  

E-Print Network [OSTI]

cold and hot air duct static pressure set points is presented. The paper also explores the interactions between the cold and hot deck temperatures and duct static pressures, and discusses the impact of non-ideal deck temperature settings on duct static...

Wei, G.; Martinez, J.; Minihan, T.; Brundidge, T.; Claridge, D. E.; Turner, W. D.

2003-01-01T23:59:59.000Z

233

CALIFORNIA ENERGY Residential Duct Placement Field Test and  

E-Print Network [OSTI]

efficiency is improved through the integrated design, construction, and operation of building systems of Small Commercial HVAC Systems Integrated Design of Commercial Building Ceiling Systems Integrated Design of the Integrated Design of Residential Ducting & Air Flow Systems research project. The reports are a result

234

Inertial particle resuspension in a turbulent, square duct flow  

Science Journals Connector (OSTI)

Particle resuspension in a turbulent square duct flow is studied using large eddy simulation combined with Lagrangian particle tracking under conditions of one-way coupling with the particle equation of motion solved with the Stokes drag lift buoyancy and gravitational force terms. Here resuspension is taken to mean the movement of particles in close proximity to the duct walls back in to the mainstream of the flow. The flow considered has a bulk Re = 250 ? k with four particle sizes ranging from 5 to 500 ? ? m examined. The results demonstrate that turbulence-driven secondary flows within the duct play an important role in the resuspension process. In the vertical direction resuspension is promoted by the drag force arising from the secondary flows which is balanced by the gravitational force with this effect increasing with decreasing particle size. In the horizontal direction particle resuspension is promoted by the particles inertial force with this effect increasing with increasing particle size. For resuspension in both directions the drag force dominates small particle resuspension while for large particles the lift force is also a contributing factor. In the horizontal direction the effect of the lift force varies with the direction of the secondary flow and becomes more significant when a particle is large or close to the duct wall. The influence of the lift force is also larger in the vertical than in the horizontal direction due to the effects of gravity.

J. Yao; M. Fairweather

2010-01-01T23:59:59.000Z

235

Reynolds-stress model prediction of 3-D duct flows  

E-Print Network [OSTI]

The paper examines the impact of different modelling choices in second-moment closures by assessing model performance in predicting 3-D duct flows. The test-cases (developing flow in a square duct [Gessner F.B., Emery A.F.: {\\em ASME J. Fluids Eng.} {\\bf 103} (1981) 445--455], circular-to-rectangular transition-duct [Davis D.O., Gessner F.B.: {\\em AIAA J.} {\\bf 30} (1992) 367--375], and \\tsn{S}-duct with large separation [Wellborn S.R., Reichert B.A., Okiishi T.H.: {\\em J. Prop. Power} {\\bf 10} (1994) 668--675]) include progressively more complex strains. Comparison of experimental data with selected 7-equation models (6 Reynolds-stress-transport and 1 scale-determining equations), which differ in the closure of the velocity/pressure-gradient tensor $\\Pi_{ij}$, suggests that rapid redistribution controls separation and secondary-flow prediction, whereas, inclusion of pressure-diffusion modelling improves reattachment and relaxation behaviour.

Gerolymos, G A

2014-01-01T23:59:59.000Z

236

Acoustic transmission in curved ducts with varying cross-sections  

Science Journals Connector (OSTI)

...asymptotically a constant at both ends of the duct, or, more precisely, (u, v) = - + O(ec1u ), u -, (u, v) = + + O(e-c2u ), u , ( 3.2) c1 and c2 being positive constants and - = 1 and + = (b/a)2 . Before we proceed with exploring conformal...

2002-01-01T23:59:59.000Z

237

Duct Thermal Performance Models for Large Commercial Buildings  

E-Print Network [OSTI]

Energy Technologies Division Indoor Environment Department Lawrence Berkeley National Laboratory Berkeley Secretary for Energy Efficiency and Renewable Energy, Building Technologies Program, of the U.S. Department) for his assistance in defining the duct surface heat transfer models described in the body of this report

238

MWTF jumper connector integral seal block development and leak testing  

SciTech Connect (OSTI)

In fiscal year 1993, tests of an o-ring/tetraseal retainer designed to replace a gasket-type seal used in PUREX-type process jumper connectors encouraged the design of an improved seal block. This new seal block combines several parts into one unitized component called an integral seal block. This report summarizes development and leak testing of the new integral seal block. The integral seal block uses a standard o-ring nested in a groove to accomplish leak tightness. This seal block eliminates the need to machine acme threads into the lower skirt casting and seal retainers, eliminates tolerance stack-up, reduces parts inventory, and eliminates an unnecessary leak path in the jumper connector assembly. This report also includes test data on various types of o-ring materials subjected to heat and pressure. Materials tested included Viton, Kalrez, and fluorosilicone, with some incidental data on teflon coated silicone o-rings. Test experience clearly demonstrates the need to test each seal material for temperature and pressure in its intended application. Some materials advertised as being {open_quotes}better{close_quotes} at higher temperatures did not perform up to expectations. Inspection of the fluorosilicone and Kalrez seals after thermal testing indicates that they are much more susceptible to heat softening than Viton.

Ruff, E.S.; Jordan, S.R.

1995-01-01T23:59:59.000Z

239

Experiments measuring particle deposition from fully developed turbulent flow in ventilation ducts  

SciTech Connect (OSTI)

Particle deposition in ventilation ducts influences particle exposures of building occupants and may lead to a variety of indoor air quality concerns. Experiments have been performed in a laboratory to study the effects of particle size and air speed on deposition rates of particles from turbulent air flows in galvanized steel and internally insulated ducts with hydraulic diameters of 15.2 cm. The duct systems were constructed of materials typically found in commercial heating, ventilating and air conditioning (HVAC) systems. In the steel duct system, experiments with nominal particle sizes of 1, 3, 5, 9 and 16 {micro}m were conducted at each of three nominal air speeds: 2.2, 5.3 and 9.0 m/s. In the insulated duct system, deposition rates of particles with nominal sizes of 1, 3, 5, 8 and 13 {micro}m were measured at nominal air speeds of 2.2, 5.3 and 8.8 m/s. Fluorescent techniques were used to directly measure the deposition velocities of monodisperse fluorescent particles to duct surfaces (floor, wall and ceiling) at two straight duct sections where the turbulent flow profile was fully developed. In steel ducts, deposition rates were higher to the duct floor than to the wall, which were, in turn, greater than to the ceiling. In insulated ducts, deposition was nearly the same to the duct floor, wall and ceiling for a given particle size and air speed. Deposition to duct walls and ceilings was greatly enhanced in insulated ducts compared to steel ducts. Deposition velocities to each of the three duct surface orientations in both systems were found to increase with increasing particle size or air velocity over the ranges studied. Deposition rates measured in the current experiments were in general agreement with the limited observations of similar systems by previous researchers.

Sippola, Mark R.; Nazaroff, William W.

2003-08-01T23:59:59.000Z

240

Flat-to-Flat Solder Seal Andrey Elagin1  

E-Print Network [OSTI]

surfaces are coated with 200nm of NiCr (80:20%) and 200nm of Cu If long time in air before sealing ­ clean1 Flat-to-Flat Solder Seal Andrey Elagin1 , Henry Frisch1 , Mary Heintz1 , Richard Northrop1 A complete LAPPD glass tile except for an aluminum photo-cathode top seal by compression on a viton o

Note: This page contains sample records for the topic "aerosol-based duct sealing" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


241

Good seal construction and ventilation controls improve airflow  

SciTech Connect (OSTI)

As workings become deeper and more distant from the ventilation inlet, better seal construction technology is needed. Tekseal, a specially formulated pumpable grout which allows a seal to be erected quickly and safety, is Minova's answer to the limitations of traditional block seals. Its use is explained in this article. An alternative product is the Carbonfill range which comprises a two-component phenolic resin based foam generating by a pump. 3 photos.

NONE

2005-12-15T23:59:59.000Z

242

Advanced configurations for leakage reduction in a labyrinth seal  

E-Print Network [OSTI]

. Stocker (1975) experimentally studied various advanced labyrinth seal configu- rations which reduce leakage by increasing the internal seal cavity turbulence. Air bubbles were used as the visualization medium and turbulence was visually evaluated...ADVANCED CONFIGURATIONS FOR LEAKAGE REDUCTION IN A LABYRINTH SEAL A Thesis by SHARATH B. VELDANDA Submitted to the Office of Graduate Studies of Texas ARM University in partial fulfillment of the requirements for the degree of MASTER...

Veldanda, Sharath B.

2012-06-07T23:59:59.000Z

243

Integral edge seals for phosphoric acid fuel cells  

DOE Patents [OSTI]

A phosphoric acid fuel cell having integral edge seals formed by an elastomer permeating an outer peripheral band contiguous with the outer peripheral edges of the cathode and anode assemblies and the matrix to form an integral edge seal which is reliable, easy to manufacture and has creep characteristics similar to the anode, cathode and matrix assemblies inboard of the seals to assure good electrical contact throughout the life of the fuel cell.

Granata, Jr., Samuel J. (South Greensburg, PA); Woodle, Boyd M. (North Huntingdon Township, Westmoreland County, PA); Dunyak, Thomas J. (Blacksburg, VA)

1992-01-01T23:59:59.000Z

244

An ideal sealed source life-cycle  

SciTech Connect (OSTI)

In the last 40 years, barriers to compliant and timely disposition of radioactive sealed sources have become apparent. The story starts with the explosive growth of nuclear gauging technologies in the 1960s. Dozens of companies in the US manufactured sources and many more created nuclear solutions to industrial gauging problems. Today they do not yet know how many Cat 1, 2, or 3 sources there are in the US. There are, at minimum, tens of thousands of sources, perhaps hundreds of thousands of sources. Affordable transportation solutions to consolidate all of these sources and disposition pathways for these sources do not exist. The root problem seems to be a lack of necessary regulatory framework that has allowed all of these problems to accumulate with no national plan for solving the problem. In the 1960s, Pu-238 displaced Pu-239 for most neutron and alpha source applications. In the 1970s, the availability of inexpensive Am-241 resulted in a proliferation of low energy gamma sources used in nuclear gauging, well logging, pacemakers, and X-ray fluorescence applications for example. In the 1980s, rapid expansion of worldwide petroleum exploration resulted in the expansion of Am-241 sources into international locations. Improvements of technology and regulation resulted in a change in isotopic distribution as Am-241 made Pu-239 and Pu-238 obsolete. Many early nuclear gauge technologies have been made obsolete as they were replaced by non-nuclear technoogies. With uncertainties in source end of life disposition and increased requirements for sealed source security, nuclear gauging technology is the last choice for modern process engineering gauging solutions. Over the same period, much was learned about licensing LLW disposition facilities as evident by the closure of early disposition facilities like Maxey Flats. The current difficulties in sealed source disposition start with adoption of the NLLW policy act of 1985, which created the state LLW compact system they we have today. This regulation created a new regulatory framework seen as promising at the time. However, now they recognize that, despite the good intentions, the NIJWP/85 has not solved any source disposition problems. The answer to these sealed source disposition problems is to adopt a philosophy to correct these regulatory issues, determine an interim solution, execute that solution until there is a minimal backlog of sources to deal with, and then let the mechanisms they have created solve this problem into the foreseeable future. The primary philosophical tenet of the ideal sealed source life cycle follows. You do not allow the creation (or importation) of any source whose use cannot be justified, which cannot be affordably shipped, or that does not have a well-delinated and affordable disposition pathway. The path forward dictates that we fix the problem by embracing the Ideal Source Life cycle. In figure 1, we can see some of the elements of the ideal source life cycle. The life cycle is broken down into four portions, manufacture, use, consolidation, and disposition. These four arbitrary elements allow them to focus on the ideal life cycle phases that every source should go through between manufacture and final disposition. As we examine the various phases of the sealed source life cycle, they pick specific examples and explore the adoption of the ideal life cycle model.

Tompkins, Joseph Andrew [Los Alamos National Laboratory

2009-01-01T23:59:59.000Z

245

Sealed One Piece Battery Having A Prism Shape Container  

DOE Patents [OSTI]

A sealed one-piece battery having a prism-shaped container including: a tank consisting of a single plastic material, a member fixed and sealed to the tank and to partitions on the side of the tank opposite the transverse wall to seal the tank, two flanges fixed and sealed to longitudinal walls defining flow compartments for a heat-conducting fluid, and two tubes on the transverse wall of the tank forming an inlet and an outlet for fluid common to the compartments.

Verhoog, Roelof (Bordeaux, FR); Barbotin, Jean-Loup (Pompignac, FR)

2000-03-28T23:59:59.000Z

246

Management of Disused Radioactive Sealed Sources in Egypt - 13512  

SciTech Connect (OSTI)

The future safe development of nuclear energy and progressive increasing use of sealed sources in medicine, research, industry and other fields in Egypt depends on the safe and secure management of disused radioactive sealed sources. In the past years have determined the necessity to formulate and apply the integrated management program for radioactive sealed sources to assure harmless and ecological rational management of disused sealed sources in Egypt. The waste management system in Egypt comprises operational and regulatory capabilities. Both of these activities are performed under legislations. The Hot Laboratories and Waste Management Center HLWMC, is considered as a centralized radioactive waste management facility in Egypt by law 7/2010. (authors)

Mohamed, Y.T.; Hasan, M.A.; Lasheen, Y.F. [Hot Laboratories and Waste Management Center, Egyptian Atomic Energy Authority, 11787, Cairo (Egypt)] [Hot Laboratories and Waste Management Center, Egyptian Atomic Energy Authority, 11787, Cairo (Egypt)

2013-07-01T23:59:59.000Z

247

Rotordynamic and leakage characteristics of a 4-stage brush seal  

E-Print Network [OSTI]

Table C9b - Static and dynamic test data for seal 3 cases with high fluid pre- rotation. 134 LIST OF FIGURES Figure 1 - Axial and cross-section views of a brush seal. Figure 2 - Forces on whirling rotor. Figure 3 - Air seal test apparatus... SCAL STATOR Figure 3 ? Air seal test apparatus. PIVOT SHAFT I S AS l4AI+ I SHAKER ROTOR HOUSING RETURN SPRING Figure 4 ? Front detail of test rig showing hydraulic shaker unit. should be independent of shake frequency. However, previous...

Conner, Kelly James

2012-06-07T23:59:59.000Z

248

Insulation and Air Sealing Products and Services | Department of Energy  

Broader source: Energy.gov (indexed) [DOE]

You are here You are here Home » Insulation and Air Sealing Products and Services Insulation and Air Sealing Products and Services May 30, 2012 - 9:52am Addthis Insulation and Air Sealing Products and Services Use the following links to get product information and locate professional services for insulation and air sealing. Product Information Cellulose Facts Cellulose Insulation Manufacturers Association Information on cellulose insulation, including technical bulletins, special reports, and video Concrete Masonry Units Concrete Homes-Portland Cement Association Describes construction methods that use concrete block systems Cotton Insulation (PDF) Build it Green Information on cotton insulation and a comparison to conventional insulation Expanded Polystyrene Molders Association

249

Sealed Radioactive Source Accountability and Control Guide  

Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

For use with Title 10, Code of Federal Regulations, Part 835, Occupational Radiation Protection. This Guide provides an acceptable methodology for establishing and operating a sealed radioactive source accountability and control program that will comply with U.S. Department of Energy (DOE) requirements specified in Title 10 of the Code of Federal Regulations (CFR), Part 835, Occupational Radiation Protection (DOE 1998a), hereinafter referred to as 10 CFR 835. In particular, this Guide provides guidance for achieving compliance with subpart M of 10 CFR 835. Canceled by DOE G 441.1-1B.

1999-04-15T23:59:59.000Z

250

RADIOACTIVE MATERIAL SHIPPING PACKAGINGS AND METAL TO METAL SEALS FOUND IN THE CLOSURES OF CONTAINMENT VESSELS INCORPORATING CONE SEAL CLOSURES  

SciTech Connect (OSTI)

The containment vessels for the Model 9975 radioactive material shipping packaging employ a cone-seal closure. The possibility of a metal-to-metal seal forming between the mating conical surfaces, independent of the elastomer seals, has been raised. It was postulated that such an occurrence would compromise the containment vessel hydrostatic and leakage tests. The possibility of formation of such a seal has been investigated by testing and by structural and statistical analyses. The results of the testing and the statistical analysis demonstrate and procedural changes ensure that hydrostatic proof and annual leakage testing can be accomplished to the appropriate standards.

Loftin, B; Glenn Abramczyk, G; Allen Smith, A

2007-06-06T23:59:59.000Z

251

LABORATORY EVALUATION OF THE DELTA Q TEST FOR DUCT LEAKAGE  

SciTech Connect (OSTI)

Using a residential-size duct system in a controlled laboratory setting, the repeatability and accuracy of the Delta Q test for air leakage in residential duct systems have been measured. More than 100 Delta Q tests were performed. These were compared with results using fan pressurization and also with results of a procedure (Delta Q Plus) that uses leakage hole-size information to select the leakage pressures to be used in the Delta Q algorithm. The average error in supply or return leakage for the fan-pressurization test was 6.4% of system fan flow. For the Delta Q test it was 3.4% of fan flow, while for Delta Q Plus it was 1.9% of fan flow.

ANDREWS,J.W.

2003-05-01T23:59:59.000Z

252

RedSeal Comments on "Smart Grid RFI: Addressing Policy and Logistical...  

Broader source: Energy.gov (indexed) [DOE]

RedSeal Comments on "Smart Grid RFI: Addressing Policy and Logistical Challenges. RedSeal Comments on "Smart Grid RFI: Addressing Policy and Logistical Challenges. RedSeal Comments...

253

Leak-rate of seals: comparison of theory with experiment  

E-Print Network [OSTI]

Seals are extremely useful devices to prevent fluid leakage. We present experimental results for the leak-rate of rubber seals, and compare the results to a novel theory, which is based on percolation theory and a recently developed contact mechanics theory. We find good agreement between theory and experiment.

B. Lorenz; B. N. J. Persson

2009-04-20T23:59:59.000Z

254

High pressure testing of see-through labyrinth seals  

E-Print Network [OSTI]

Detailed results are presented for teeth-on-stator labyrinth seals tested under high pressure of 70 bar-a (1015 psi-a) and 52 bar-a (754 psi-a) in the centered position. The seals were tested at pressure ratios of 0.52, 0.36 and 0.16, speeds of 10...

Picardo, Arthur Michael

2012-06-07T23:59:59.000Z

255

Dry compliant seal for phosphoric acid fuel cell  

DOE Patents [OSTI]

A dry compliant overlapping seal for a phosphoric acid fuel cell preformed f non-compliant Teflon to make an anode seal frame that encircles an anode assembly, a cathode seal frame that encircles a cathode assembly and a compliant seal frame made of expanded Teflon, generally encircling a matrix assembly. Each frame has a thickness selected to accommodate various tolerances of the fuel cell elements and are either bonded to one of the other frames or to a bipolar or end plate. One of the non-compliant frames is wider than the other frames forming an overlap of the matrix over the wider seal frame, which cooperates with electrolyte permeating the matrix to form a wet seal within the fuel cell that prevents process gases from intermixing at the periphery of the fuel cell and a dry seal surrounding the cell to keep electrolyte from the periphery thereof. The frames may be made in one piece, in L-shaped portions or in strips and have an outer perimeter which registers with the outer perimeter of bipolar or end plates to form surfaces upon which flanges of pan shaped, gas manifolds can be sealed.

Granata, Jr., Samuel J. (South Greensburg, PA); Woodle, Boyd M. (N. Huntingdon Township, Westmoreland County, PA)

1990-01-01T23:59:59.000Z

256

Fuel cell generator containing a gas sealing means  

DOE Patents [OSTI]

A high temperature solid electrolyte electrochemical generator is made, operating with flowing fuel gas and oxidant gas, the generator having a thermal insulation layer, and a sealing means contacting or contained within the insulation, where the sealing means is effective to control the contact of the various gases utilized in the generator.

Makiel, Joseph M. (Monroeville, PA)

1987-01-01T23:59:59.000Z

257

New Sealing Concept for Planar Solid Oxide Fuel Cells  

SciTech Connect (OSTI)

A key element in developing high performance planar solid oxide fuel cell stacks is the hermetic seal between the metal and ceramic components. There are two methods of sealing that are commonly employed: (1) rigid joining or (2) compressive sealing. Each method has its own set of advantages and design constraints. An alternative approach is currently under development that appears to combine some of the advantages of the other two techiques, including hermeticity, mechanical integrity, and minimization of interfacial stresses in either of the joint substrate materials, particulary the ceramic. The new sealing concept relies on a plastically deformable metal seal; one that offers a quasi-dynamic mechanical response in that it is adherent to both sealing surfaces, i.e. non-sliding, but readily yields or deforms under thermally generated stresses, thereby mitigating the development of stresses in the adjacent ceramic and metal components even when a significant difference in thermal expansion exists between the two materials. The pre-experimental design of the seal, initial proof-of-principle results on small test specimens, and finite element analyses aimed at scaling the seal to prototypical sizes and geometries are described herein.

Weil, K. Scott; Hardy, John S.; Koeppel, Brian J.

2006-08-01T23:59:59.000Z

258

Fuel cell generator containing a gas sealing means  

DOE Patents [OSTI]

A high temperature solid electrolyte electrochemical generator is made, operating with flowing fuel gas and oxidant gas, the generator having a thermal insulation layer, and a sealing means contacting or contained within the insulation, where the sealing means is effective to control the contact of the various gases utilized in the generator. 5 figs.

Makiel, J.M.

1987-02-03T23:59:59.000Z

259

INTRODUCTION Northern elephant seals, Mirounga angustirostris Gill 1866, spend  

E-Print Network [OSTI]

629 INTRODUCTION Northern elephant seals, Mirounga angustirostris Gill 1866, spend most, requiring them to find the correct colony among these sites at the end of their long migration. Elephant). However, it remains unknown how they guide themselves back to the colony. Elephant seals dive nearly

Costa, Daniel P.

260

(ENFORCEMENT AGENCY CAN CUSTOMIZE WITH LETTERHEAD/SEAL)  

E-Print Network [OSTI]

sealing ­ The installer is to insure leakage of the HVAC system is less than 6% for new air conditioning(ENFORCEMENT AGENCY CAN CUSTOMIZE WITH LETTERHEAD/SEAL) 2008 Building Energy Efficiency Standards have a minimum 78% AFUE (Exception: Wall & floor furnaces; room heaters). 2. Central air conditioners

Note: This page contains sample records for the topic "aerosol-based duct sealing" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


261

(ENFORCEMENT AGENCY CAN CUSTOMIZE WITH LETTERHEAD/SEAL  

E-Print Network [OSTI]

(ENFORCEMENT AGENCY CAN CUSTOMIZE WITH LETTERHEAD/SEAL 2008 Building Energy Efficiency Standards have a minimum 78% AFUE (Exception: Wall & floor furnaces; room heaters). 2. Central air conditioners of Section 150(m): · All joints and openings in the HVAC system must be sealed. · Only UL 181, UL 181A, or UL

262

(ENFORCEMENT AGENCY CAN CUSTOMIZE WITH LETTERHEAD/SEAL)  

E-Print Network [OSTI]

(ENFORCEMENT AGENCY CAN CUSTOMIZE WITH LETTERHEAD/SEAL) 2008 Building Energy Efficiency Standards have a minimum 78% AFUE (Exception: Wall & floor furnaces; room heaters). 2. Central air conditioners the mandatory requirements of Section 150(m): · All joints and openings in the in the HVAC system must be sealed

263

(ENFORCEMENT AGENCY CAN CUSTOMIZE WITH LETTERHEAD/SEAL)  

E-Print Network [OSTI]

(ENFORCEMENT AGENCY CAN CUSTOMIZE WITH LETTERHEAD/SEAL) 2008 Building Energy Efficiency Standards have a minimum 78% AFUE (Exception: Wall & floor furnaces; room heaters). 2. Central air conditioners of Section 150(m): · All joints and openings in the HVAC system must be sealed. · Only UL 181, UL 181A, or UL

264

On the Sealing of Electrical Conductors through Glass  

Science Journals Connector (OSTI)

... AT the present time there is great difficulty in obtaining soft glass with a comparatively high coefficient of expansion, suitable for sealing wires into ... with a comparatively high coefficient of expansion, suitable for sealing wires into glass tubes, bulbs, etc. The pre-war imported stocks of ...

F. F. S. BRYSON

1915-06-03T23:59:59.000Z

265

Air Sealing for New Home Construction | Department of Energy  

Broader source: Energy.gov (indexed) [DOE]

for New Home Construction for New Home Construction Air Sealing for New Home Construction May 2, 2012 - 6:09pm Addthis Air Sealing for New Home Construction What does this mean for me? Air sealing your house properly during construction will save you energy and money. Ideally, air-sealing techniques are tailored to your site and climate zone. How does it work? Workers will seal all the paths that air can leak in and out of your new home during construction. This process requires care and attention to detail, and it's best to hire professionals with experience building energy-efficient homes. Minimizing air movement in and out of a house is key to building an energy-efficient home. Controlling air leakage is also critical to moisture control. It's always best to use techniques and materials identified as best

266

Asphalt emulsion sealing of uranium mill tailings. 1980 annual report  

SciTech Connect (OSTI)

Studies of asphalt emulsion sealants conducted by the Pacific Northwest Laboratory have demonstrated that the sealants are effective in containing radon and other potentially hazardous material within uranium tailings. The laboratory and field studies have further demonstrated that radon exhalation from uranium tailings piles can be reduced by greater than 99% to near background levels. Field tests at the tailings pile in Grand Junction, Colorado, confirmed that an 8-cm admix seal containing 22 wt% asphalt could be effectively applied with a cold-mix paver. Other techniques were successfully tested, including a soil stabilizer and a hot, rubberized asphalt seal that was applied with a distributor truck. After the seals were applied and compacted, overburden was applied over the seal to protect the seal from ultraviolet degradation.

Hartley, J.N.; Koehmstedt, P.L; Esterl, D.J.; Freeman, H.D.; Buelt, J.L.; Nelson, D.A.; Elmore, M.R.

1981-05-01T23:59:59.000Z

267

Photogrammetry as a tool for estimating size and condition in the Hawaiian monk seal (Monachus schauinslandi), the harbor seal (Phoca vitulina), and the northern elephant seal (Mirounga anguistirosis)  

E-Print Network [OSTI]

) for captive, subadult, Hawaiian monk seals M= 58. 18 + 9. 07 (GA) + 1. 20 (LA) - 0. 46 (L) -0. 64 (GP). . . . . . . . . . . . . . . . . . . 65 FIGURE Page The two best models reflecting the relationship of mass with photogrammetric and morphometric... The relationship of mass with photogrammetric measures for captive, adult harbor seals: M= -204. 597 - 6. 834 (GA) + 1. 538 (GP) + 0. 554(LP) + 0. 217 (L) . . . . 71 The relationship between body mass and photogrammetric measures of lateral perimeter (LP...

McFadden, Katherine Walton

2012-06-07T23:59:59.000Z

268

System design and performance of a spiral groove gas seal for hydrogen service  

SciTech Connect (OSTI)

In the past, typical seal designs for low molecular weight gases, such as hydrogen, incorporated high pressure oil seal systems. Technology of the seventies and eighties produced a new concept - the spiral groove gas seal. This paper discusses the problems related to oil seal systems, as well as the design, application and performance of a dry gas seal. It also discusses the limitations encountered with the start-up and operation of a dry gas seal in a high pressure, oil-soluble mixture of light hydrocarbons. Results show how the spiral groove gas seal can handle adverse demands without seal failure.

Pecht, G.G.; Carter, D. (John Crane, Inc., Morton Grove, IL (USA) Marathon Petroleum Co., Robinson, IL (USA))

1990-09-01T23:59:59.000Z

269

E-Print Network 3.0 - antarctic fur seals Sample Search Results  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

population of New Zealand fur seals (Arctocephalus forsteri) Summary: and southern elephant seals at Gough Island. S. Afr. J. Antarct. Res. 20: 912. Bonner, W. N. (1968). The...

270

Microstructure-based solid oxide fuel cell seal design using statistical mechanics.  

E-Print Network [OSTI]

??Solid oxide fuel cells (SOFC) in a flat-plate configuration require a hermetic seal between the fuel and air sides of the electrodes, and this seal (more)

Milhans, Jacqueline Linda

2010-01-01T23:59:59.000Z

271

E-Print Network 3.0 - apical seal comparison Sample Search Results  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

seal between epithelial... seal. This apical junction might therefore serve as a permeability barrier. Consistent... characterized the novel coiled-coil protein AJM-1, which...

272

High-Temperature Zirconia Oxygen Sensor with Sealed Metal/Metal...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

High-Temperature Zirconia Oxygen Sensor with Sealed MetalMetal Oxide Internal Reference High-Temperature Zirconia Oxygen Sensor with Sealed MetalMetal Oxide Internal Reference...

273

Building America Top Innovations 2013 Profile … Buried and Encapsulated Ducts  

Broader source: Energy.gov (indexed) [DOE]

match the performance of ducts in conditioned space. match the performance of ducts in conditioned space. For years builders have designed their homes with the HVAC ducts in the attic. There is plenty of space up there to run the ducts, and if the air handler is located in the attic as well, it is not taking up valuable square footage inside the home. The only problem is vented attics can be very hot in the summer and very cold in the winter. Estimated thermal losses through ducts installed in unconditioned attics range from 10% to 45%, contributing significantly to homeowners' heating and cooling costs. The Consortium for Advanced Residential Buildings (CARB), a Building America research team led by Steven Winter Associates, has done extensive research on the feasibility of insulating ducts that are located in the attic and has

274

Building America Top Innovations 2013 Profile … Buried and Encapsulated Ducts  

Broader source: Energy.gov (indexed) [DOE]

meet the code requirements for ducts in conditioned space. meet the code requirements for ducts in conditioned space. For years builders have designed their homes with the HVAC ducts in the attic. There is plenty of space up there to run the ducts and if the air handler is located in the attic as well, it's not taking up valuable square footage inside the home. The only problem is uninsulated attics can be very hot in the summer and very cold in the winter. Estimated thermal losses through ducts installed in unconditioned attics range from 10% to 45%, contributing significantly to homeowners' heating and cooling costs. The Consortium for Advanced Residential Buildings (CARB), a Building America research team led by Steven Winter Associates, has done extensive research on the feasibility of insulating ducts that are located in the attic and has

275

Building America Top Innovations Hall of Fame Profile … Ducts in Conditioned Space  

Broader source: Energy.gov (indexed) [DOE]

A duct chase in a dropped hallway ceiling A duct chase in a dropped hallway ceiling provides an affordable way to put ducts in conditioned space, a technique that saves energy and improves indoor air quality. Moving ductwork into the home's conditioned space can save 8%-15% on homeowner air-conditioning bills. Thousands of homes are now applying this important best practice promoted by Building America research. BUILDING AMERICA TOP INNOVATIONS HALL OF FAME PROFILE INNOVATIONS CATEGORY: 1. Advanced Technologies and Practices 1.1 Building Science Solutions: Thermal Enclosure Ducts in Conditioned Space Putting ducts in vented, unconditioned crawlspaces and attics makes almost no sense from a building science standpoint. Building America research has provided proven solutions for locating ducts in conditioned space that are being adopted by

276

Characteristics of multimode heat transfer in a differentially-heated horizontal rectangular duct.  

E-Print Network [OSTI]

??This study presents the numerical analysis of steady laminar flow heat transfer in a horizontal rectangular duct with differential heating on the vertical walls. Three (more)

Wangdhamkoom, Panitan

2007-01-01T23:59:59.000Z

277

Using seals to control flow at Yucca Mountain  

SciTech Connect (OSTI)

This paper describes how an interpretation of regulations can lead to innovative solutions to the problem of sealing subsurface openings in the highly fractured rock above the water table at Yucca Mountain, Nevada, which is being characterized to determine its suitability for a repository for spent fuel and high level waste. The paper concentrates on the functional requirements for seals as well as the statutory definitions given in 10 CFR Part 60. Because the main concern of sealing is to prevent the flow of water to the waste packages or radionuclides to the accessible environment, the main strategy for sealing of the proposed repository is to control rather than stop the flow of water. Other functions of seals include the prevention of human intrusion and the control of the flow of gaseous radionuclides. This paper describes the concepts that have thus far been developed for sealing with respect to shafts, ramps, boreholes, and the underground facility rather than detailed numerical analysis and design for seals. The main emphasis of this paper is on the role of regulations in providing flexibility in dealing with a complex, long-term component.

Blair, J.A. [TRW Environmental Safety Systems Inc., Washington, DC (US); Stucker, D.; Kumar, P. [USDOE Office of Civilian Radioactive Waste Management, Washington, DC (United States)

1992-11-01T23:59:59.000Z

278

Tamper-indicating seals : practices, problems, and standards  

SciTech Connect (OSTI)

Tamper-indicating seals have been used by customs officials for over 7,000 years. Today, seals are widely used to help counter theft, smuggling, sabotage, vandalism, terrorism, and espionage. Despite their antiquity and modern widespread use, however, there remains considerable confusion about seals, as well as a lot of misconceptions, wishful thinking, sloppy terminology, and poor practice. The absence of meaningful norms and standards, together with the surprisingly limited amount of research and development (R&D) in the field of tamper detection, has also hindered the effective use of seals. The Vulnerability Assessment Team (VAT) at Los Alamos National Laboratory has intensively studied tamper-indicating seals for the last 12 years. We have engaged in vulnerability assessments, R&D, consulting, and training for over two dozen United States government agencies and private companies, as well as for the International Atomic Energy Agency (IAEA) and Euratom. The VAT has also analyzed over 200 different types of seals in detail. This paper summarizes some of our conclusions, recommendations, and warnings regarding seals and tamper detection.

Johnston, R. G. (Roger G.)

2003-01-01T23:59:59.000Z

279

Sea Mammal Research Unit Report on recent seal mortalities in UK  

E-Print Network [OSTI]

......................................................... 11 7. Mechanism of Injury: Ducted propellers ........................................ 12 8 sharks ......................................................... 15 8.6. Tidal turbines through a ducted propeller such as a Kort nozzle or some types of Azimuth thrusters. Such systems

Brierley, Andrew

280

Trap seal for open circuit liquid cooled turbines  

DOE Patents [OSTI]

An improved trap seal for open circuit liquid cooled turbines is disclosed. The trap seal of the present invention includes an annular recess formed in the supply conduit of cooling channels formed in the airfoil of the turbine buckets. A cylindrical insert is located in the annular recesses and has a plurality of axial grooves formed along the outer periphery thereof and a central recess formed in one end thereof. The axial grooves and central recess formed in the cylindrical insert cooperate with the annular recess to define a plurality of S-shaped trap seals which permit the passage of liquid coolant but prohibit passage of gaseous coolant.

Grondahl, Clayton M. (Clifton Park, NY); Germain, Malcolm R. (Ballston Lake, NY)

1980-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "aerosol-based duct sealing" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


281

Flexible edge seal for vacuum insulating glazing units  

SciTech Connect (OSTI)

A flexible edge seal is provided for a vacuum insulating glazing unit having a first glass pane and a second glass pane spaced-apart from the first. The edge seal comprises a seal member formed of a hermetically bondable material and having a first end, a second end and a center section disposed therebetween. The first end is hermetically bondable to a first glass pane. The second end is hermetically bondable to a second glass pane. The center section comprises a plurality of convolutes.

Bettger, Kenneth J.; Stark, David H.

2012-12-11T23:59:59.000Z

282

Duct Remediation Program: Material characterization and removal/handling  

SciTech Connect (OSTI)

Remediation efforts were successfully performed at Rocky Flats to locate, characterize, and remove plutonium holdup from process exhaust ducts. Non-Destructive Assay (NDA) techniques were used to determine holdup locations and quantities. Visual characterization using video probes helped determine the physical properties of the material, which were used for remediation planning. Assorted equipment types, such as vacuum systems, scoops, brushes, and a rotating removal system, were developed to remove specific material types. Personnel safety and material handling requirements were addressed throughout the project.

Beckman, T.d.; Davis, M.M.; Karas, T.M.

1992-11-01T23:59:59.000Z

283

The economics of the use of cermet seals in steam turbines  

Science Journals Connector (OSTI)

The use of cermet sealing materials in steam turbines improves their reliability and produces considerable savings...

Z. P. Dorf; . T. Denisenko

1965-04-01T23:59:59.000Z

284

Climate change and seal survival: evidence for environmentally mediated changes in elephant  

E-Print Network [OSTI]

Climate change and seal survival: evidence for environmentally mediated changes in elephant seal in the first year of life for southern elephant seals. We present evidence linking climate (ENSO; Kwok & Comiso 2002) because predators such as southern elephant seals (SESs) range widely across

Hays, Graeme

285

Development of a 20x20cm2 'hot' indium-alloy hermetic seal  

E-Print Network [OSTI]

If long time in air before sealing ­ clean with Micro-90 and rinse with DI water 'Hot' Seal #12;8 Step 21 Development of a 20x20cm2 'hot' indium-alloy hermetic seal in an inert atmosphere for photo glass tile except for an aluminum photo-cathode top seal by compression on a viton o-ring active

286

DOE Logo, Seal and Word Mark | Department of Energy  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Graphics » DOE Logo, Seal and Graphics » DOE Logo, Seal and Word Mark DOE Logo, Seal and Word Mark The DOE logo, seal, and word mark are official graphical identifiers of the U.S. Department of Energy and are meant for official use only, to represent the Department's official position. They may be used to recognize funding or official support by the Department if the usage has proper qualifying language to explain its presence on non-DOE materials and it is reviewed and explicitly approved by the Department. They cannot be used in a manner that has an implied or explicit endorsement of any private company, service or product. There is a Code of Federal Regulations (CFR) regarding the DOE graphical identifier at: http://www.gpo.gov/fdsys/pkg/CFR-2000-title10-vol4/xml/CFR-2000-title10-vol4-part1002.xml

287

Emergence of Fatal Avian Influenza in New England Harbor Seals  

Science Journals Connector (OSTI)

...and Bayesian algorithms. Models of evolution were selected...To create a homology model of the seal 2012 outbreak HA sequence, 10 template models were selected based on...NSF TW005769; USAID PREDICT; and DTRA. We thank Nicole...

S. J. Anthony; J. A. St. Leger; K. Pugliares; H. S. Ip; J. M. Chan; Z. W. Carpenter; I. Navarrete-Macias; M. Sanchez-Leon; J. T. Saliki; J. Pedersen; W. Karesh; P. Daszak; R. Rabadan; T. Rowles; W. I. Lipkin

2012-08-01T23:59:59.000Z

288

Design and vibration testing of a flexible seal whisker model  

E-Print Network [OSTI]

Harbor seal whiskers have a unique surface structure that dramatically reduces vortex induced vibrations as they move through the water. Concurrently with rigid whisker experiments, this project focuses on the design and ...

Gerber, Christopher D

2013-01-01T23:59:59.000Z

289

#AskEnergySaver: Air Sealing | Department of Energy  

Energy Savers [EERE]

the reason warm air rises. You should consider several factors before choosing which to air seal first, including which leaks are the largest, which are easiest to fix and the...

290

Attic Air Sealing Guide- Building America Top Innovation  

Broader source: Energy.gov [DOE]

The Building America-sponsored Guide to Attic Air Sealing provides much needed instruction essential to achieving effective energy savings while avoiding pitfalls that can lead to combustion safety and indoor air quality issues.

291

Flow visualization and leakage measurements of labyrinth seals  

E-Print Network [OSTI]

A large scale test rig is used to conduct an experimental investigation into the leakage resistance properties and flow characteristics of labyrinth seals. A novel test facility with multiple cavities that provides 2D, planar flow at a scale...

Johnson, James Wayne

1996-01-01T23:59:59.000Z

292

A NUMERICAL AND EXPERIMENTAL STUDY OF WINDBACK SEALS  

E-Print Network [OSTI]

performance and the flow field inside the seal. The leakage flow rate increases with increasing the pressure differential, rotor speed, radial clearance, cavity size, and shaft diameter and with decreasing the tooth width. The eccentricity has a minimal effect...

Lim, Chae H.

2010-01-16T23:59:59.000Z

293

Numerical simulation of laminar flow in a curved duct  

SciTech Connect (OSTI)

This paper describes numerical simulations that were performed to study laminar flow through a square duct with a 900 bend. The purpose of this work was two fold. First, an improved understanding was desired of the flow physics involved in the generation of secondary vortical flows in three-dimensions. Second, adaptive gridding techniques for structured grids in three- dimensions were investigated for the purpose of determining their utility in low Reynolds number, incompressible flows. It was also of interest to validate the commercial computer code CFD-ACE. Velocity predictions for both non-adaptive and adaptive grids are compared with experimental data. Flow visualization was used to examine the characteristics of the flow though the curved duct in order to better understand the viscous flow physics of this problem. Generally, moderate agreement with the experimental data was found but shortcomings in the experiment were demonstrated. The adaptive grids did not produce the same level of accuracy as the non-adaptive grid with a factor of four more grid points.

Lopez, A.R.; Oberkampf, W.L.

1995-01-01T23:59:59.000Z

294

Effect of a straight teeth-on-rotor labyrinth seal on rotordynamics  

E-Print Network [OSTI]

of the stiffness and STATOR AIR FLOW ROTOR STATOR Teeth-on-Stator Seal Teeth-on-Rotor Seal Figure 2. Two Types of Labyrinth Seal Configurations Figure 3. Teeth-on-Rotor Labyrinth Seal Figure 4. Teeth-on-Rotor Labyrinth Seals Installed on Rotor damping... of the test rig is shown in Figure 6. Sea 2 Eddy Probes al 90 (Plane 1) Rotor 0 0 0 0 0 0 0 0 0 0 2 Eddy Probes at 90' (Plans 3) Anti-swirl Vane ? Flywheel 0-Rings 0-Ring 3 Compressed Air Cannon)iona 120' Apart Labyrinth Seal Area Seal...

Zierer, Joseph John

2012-06-07T23:59:59.000Z

295

Laboratory Testing of Aerosol for Enclosure Air Sealing  

SciTech Connect (OSTI)

Space conditioning energy use can be significantly reduced by addressing uncontrolled infiltration and exfiltration through the envelope of a building. A process for improving the air tightness of a building envelope by sealing shell leaks with an aerosol sealing technology is presented. Both retrofit and new construction applications are possible through applying this process either in attics and crawlspaces or during rough-in stage.

Harrington, C.; Modera, M.

2012-05-01T23:59:59.000Z

296

Leakage estimation of incompressible fluids in stepped labyrinth seals  

E-Print Network [OSTI]

factor g = acceleration due to gravity h = height of tooth m = pitch of tooth m = mass flowrate n = number of throttles r = tooth to step distance s = width of tooth t = step height in stepped labyrinth seals u = fluid velocity spec'fic volume... D = seal diameter H OC = tooth height to clearance ratio pressure Re = Reynolds number WTOP tooth width to pitch ratio flow coefficient car v-over coefficient absolute viscosity kinematic viscosity xv1 aensity subscripts: o = inlet value...

Chi, Daesung

2012-06-07T23:59:59.000Z

297

Method for forming glass-to-metal seals  

DOE Patents [OSTI]

A method for forming a glass-to-metal seal in which the glass has a higher melting point than the metal. The molten glass is vacuum injection molded onto the metal, thus melting a very thin layer of the surface of the metal long enough to form a seal, but not long enough to cause a distortion in the shape of the metal component.

Kramer, Daniel P. (Dayton, OH); Massey, Richard T. (Hamilton, OH)

1986-01-01T23:59:59.000Z

298

A Zero Emission Mechanical Seal with Integral Micro Heat Exchanger  

E-Print Network [OSTI]

/689,406) with an internal heat exchanger within the body of the mating ring that channels a coolant toward the interface to effectively cool the seal faces. The coolant may be either liquid or gas, such as instrument air. This research is in part supported by a...An Industrial Zero Emission Seal with Improved Heat Transfer Characteristics Michael Khonsari Dow Chemical Endowed Chair in Rotating Machinery and Professor Center for Rotating Machinery Department of Mechanical Engineering Louisiana State...

Khonsari, M.

2005-01-01T23:59:59.000Z

299

Inflatable containment diaphragm for sealing and removing stacks  

DOE Patents [OSTI]

A diaphragm with an inflatable torus-shaped perimeter is used to seal at least one end of a stack so that debris that might be hazardous will not be released during removal of the stack. A diaphragm is inserted and inflated in the lower portion of a stack just above where the stack is to be cut such that the perimeter of the diaphragm expands and forms a seal against the interior surface of the stack.

Meskanick, G.R.; Rosso, D.T.

1993-04-13T23:59:59.000Z

300

Measure Guideline: Air Sealing Attics in Multifamily Buildings  

SciTech Connect (OSTI)

This Building America Measure Guideline is intended for owners, builders, contractors, homeowners, and other stakeholders in the multifamily building industry, and focuses on challenges found in existing buildings for a variety of housing types. It explains why air sealing is desirable, explores related health and safety issues, and identifies common air leakage points in multifamily building attics. In addition, it also gives an overview of materials and techniques typically used to perform air sealing work.

Otis, C.; Maxwell, S.

2012-06-01T23:59:59.000Z

Note: This page contains sample records for the topic "aerosol-based duct sealing" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


301

Static Pressure Loss in 12, 14, and 16 Non-metallic Flexible Duct  

E-Print Network [OSTI]

This study was conducted to determine the effects of compression on pressure drops in non-metallic flexible duct. Duct sizes of 12, 14 and 16 diameters were tested at a five different compression ratios (maximum stretch, 4%, 15%, 30% and 45...

Cantrill, David Lee

2013-08-01T23:59:59.000Z

302

Multi-carrier Signal Transmission through HVAC Ducts: Experimental Results for Channel Capacity  

E-Print Network [OSTI]

Multi-carrier Signal Transmission through HVAC Ducts: Experimental Results for Channel Capacity, for the first time, experimental results on channel capacity of heating, ventilation, and air-conditioning (HVAC through a building HVAC duct system demonstrate the ability to transmit with a spectral efficiency of 3

Stancil, Daniel D.

303

Seamless Handover in Buildings Using HVAC Ducts: A New System Architecture  

E-Print Network [OSTI]

Seamless Handover in Buildings Using HVAC Ducts: A New System Architecture Ariton E. Xhafa, Paisarn-- In this paper, we present an innovative solution to the handover problem in multi-story buildings using HVAC of the indoor wireless networks that use the heating, ventilation, and air conditioning (HVAC) ducts

Stancil, Daniel D.

304

96 ASHRAE Transactions: Research Current duct design methods for variable air volume  

E-Print Network [OSTI]

.Hourlyairflowrequirements, part-load fan characteristics, and duct static pressure control are incorporated into the problem airflow. Fan power is also influ- enced if static pressure at the end of the longest duct line for effective, energy-efficient, and comfortable heating, ventilat- ing, and air-conditioning (HVAC) systems

305

Beat phenomenon at the arrival of a guided mode in a semi-infinite acoustic duct  

E-Print Network [OSTI]

. This eigen value problem has an infinite discrete number of solutions N (x, y) with the modal wave numbers NBeat phenomenon at the arrival of a guided mode in a semi-infinite acoustic duct P. Gatignola , M at an initial time in the terminal section of a semi-infinite acoustic duct, will undergo dispersion effects

Paris-Sud XI, Université de

306

Gas-path leakage seal for a gas turbine  

DOE Patents [OSTI]

A gas-path leakage seal is described for generally sealing a gas-path leakage-gap between spaced-apart first and second members of a gas turbine (such as combustor casing segments). The seal includes a generally imperforate foil-layer assemblage which is generally impervious to gas and is located in the leakage-gap. The seal also includes a cloth-layer assemblage generally enclosingly contacting the foil-layer assemblage. In one seal, the first edge of the foil-layer assemblage is left exposed, and the foil-layer assemblage resiliently contacts the first member near the first edge to reduce leakage in the ``plane`` of the cloth-layer assemblage under conditions which include differential thermal growth of the two members. In another seal, such leakage is reduced by having a first weld-bead which permeates the cloth-layer assemblage, is attached to the metal-foil-layer assemblage near the first edge, and unattachedly contacts the first member. 4 figs.

Wolfe, C.E.; Dinc, O.S.; Bagepalli, B.S.; Correia, V.H.; Aksit, M.F.

1996-04-23T23:59:59.000Z

307

Tags and seals to strengthen arms control verification  

SciTech Connect (OSTI)

Tags and seals have long been recognized as important tools in arms control. The trend in control of armaments is to limit militarily significant equipment that is capable of being verified through direct and cooperative means, chiefly on-site inspection or monitoring. Although this paper will focus on the CFE treaty, the role of tags and seals for other treaties will also be addressed. Published technology and concepts will be reviewed, based on open sources. Arms control verification tags are defined as unique identifiers designed to be tamper-revealing; in that respect, seals are similar, being used as indicators of unauthorized access. Tamper-revealing tags are intended as single-point markers, seals for two-point couplings, and nets for volume containment. Seals usually bind two separate components, such as a hatch or flange that provides access to a secure compartment or a valve that controls fluid flow. A tamper-revealing net might be comprised of a coupled fiberoptic bundle wrapped around an object. Sometimes the term ``seal`` is used to denote the tamper-revealing feature of a tag that is attached to a surface, but in this paper the tamper-indicating connection is considered to be part of the tag concept itself.

DeVolpi, A.

1990-10-03T23:59:59.000Z

308

Determining Critical Pressure and Duct Leakage in VAV Air-Handling Units  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Determining Critical Pressure and Duct Leakage in VAV Air-Handling Units Determining Critical Pressure and Duct Leakage in VAV Air-Handling Units Speaker(s): Clifford Federspiel Date: December 3, 2003 - 12:00pm Location: Bldg. 90 Seminar Host/Point of Contact: Nance Matson Fans for moving air in buildings use a significant amount of energy. It is well known that fan energy use in variable-air-volume (VAV) systems can be reduced by resetting the supply duct pressure. The standard way to reset duct pressure is by controlling the most-open terminal damper to a nearly open position. Most systems can't measure terminal damper positions, so pressures are either not reset at all or use ad hoc resetting strategies that are configured sub-optimally. In this seminar I will describe a new method of determining the critical supply duct pressure for VAV systems.

309

Experimental rotordynamic coefficient results for: (a) a labyrinth seal with and without shunt injection and (b) a honeycomb seal  

E-Print Network [OSTI]

Centrifugal compressors are increasingly required to operate in higher pressure, higher speed, and large fluid density. In these conditions, compressors are susceptible to rotordynamic instabilities. To avoid this situation, labyrinth seals have...

Soto Azuaje, Elias Antonio

1997-01-01T23:59:59.000Z

310

7/11/00-draft copy: do not quote 1 of 30 New Technologies for Residential HVAC Ducts  

E-Print Network [OSTI]

7/11/00-draft copy: do not quote 1 of 30 New Technologies for Residential HVAC Ducts Burke Treidler is not evaluated and HVAC contractors overcome duct system shortcomings by installing oversized equipment Technologies for Residential HVAC Ducts fittings with some use of ductboard. Fittings that snap together were

311

IEEE TRANSACTIONS ON COMMUNICATIONS, VOL. 53, NO. 2, FEBRUARY 2005 335 On the Capacity Limits of HVAC Duct Channel for  

E-Print Network [OSTI]

of HVAC Duct Channel for High-Speed Internet Access Ariton E. Xhafa, Member, IEEE, Ozan K. Tonguz, Member and experimental channel-capacity estimates of heating, ventilation, and air condi- tioning (HVAC) ducts based suppressed. Our experimental results also show that even in the case of more complex HVAC duct networks (i

Stancil, Daniel D.

312

DOE Challenge Home Technical Training - Ducts in Conditioned Space  

Broader source: Energy.gov (indexed) [DOE]

T T h i l T i i 1 | INNOVATION & INTEGRATION: Transforming the Energy Efficiency Market Buildings.Energy.gov Design Options for Locating Ducts within Conditioned Space DOE Challenge Home Bill Zoeller, RA Steven Winter Associates Technical Training Congratulations By designing, constructing, and verifying DOE Challenge Homes, y you are: * in a select group Only the top one percent of builders in the country meets the extraordinary energy efficiency, comfort, health, safety, durability and quality levels associated with the DOE Challenge Home. * providing unprecedented value Your customers receive immediate energy savings of 40-50% easy to adapt to net-zero performance with a small renewable energy system. * differentiated from the competition About 12 in 13 homes sales nationwide are 'used' homes. In addition, the majority of new

313

CFD simulation of leak in residential HVAC ducts  

Science Journals Connector (OSTI)

A three-dimensional computational fluid dynamics model was used to simulate fluid flow in a duct and its simulated leaks with six different air leak geometries placed respectively on its periphery. The k? turbulence model for high Reynolds numbers flows was used for that purpose and the Reynolds numbers were varied to simulate a variety of flow conditions between 27,000 and 82,000. The computer code was used to produce pressure drop data and leak flow rates across the holes necessary to compute the pressure loss coefficients, as well as to produce flow field and static pressure plots that offer insight into the physics of the flow field. The flow coefficient and pressure exponent (C and n) were found for different leak geometries by curve fitting the pressure and leak flow data derived from CFD simulations and were compared to available data in the literature.

Samir Moujaes; Radhika Gundavelli

2012-01-01T23:59:59.000Z

314

Development and evaluation of sealing technologies for photovoltaic panels  

SciTech Connect (OSTI)

This report summarizes the results of a study to develop and evaluate low temperature glass sealing technologies for photovoltaic applications. This work was done as part of Cooperative Research and Development Agreement (CRADA) No. SC95/01408. The sealing technologies evaluated included low melting temperature glass frits and solders. Because the glass frit joining required a material with a melting temperature that exceeded the allowable temperature for the active elements on the photovoltaic panels a localized heating scheme was required for sealing the perimeter of the glass panels. Thermal and stress modeling were conducted to identify the feasibility of this approach and to test strategies designed to minimize heating of the glass panel away from its perimeter. Hardware to locally heat the glass panels during glass frit joining was designed, fabricated, and successfully tested. The same hardware could be used to seal the glass panels using the low temperature solders. Solder adhesion to the glass required metal coating of the glass. The adhesion strength of the solder was dependent on the surface finish of the glass. Strategies for improving the polyisobutylene (PIB) adhesive currently being used to seal the panels and the use of Parylene coatings as a protective sealant deposited on the photovoltaic elements were also investigated. Starting points for further work are included.

Glass, S.J.; Hosking, F.M.; Baca, P.M. [and others

1998-07-01T23:59:59.000Z

315

An integrated approach to fire penetration seal program management  

SciTech Connect (OSTI)

This paper discusses the utilization of a P.C. based program to facilitate the management of Entergy Operations Arkansas Nuclear One (ANO) fire barrier penetration seal program. The computer program was developed as part of a streamlining process to consolidate all aspects of the ANO Penetration Seal Program under one system. The program tracks historical information related to each seal such as maintenance activities, design modifications and evaluations. The program is integrated with approved penetration seal design details which have been substantiated by full scale fire tests. This control feature is intended to prevent the inadvertent utilization of an unacceptable penetration detail in a field application which may exceed the parameters tested. The system is also capable of controlling the scope of the periodic surveillance of penetration seals by randomly selecting the inspection population and generating associated inspection forms. Inputs to the data base are required throughout the modification and maintenance process to ensure configuration control and maintain accurate data base information. These inputs are verified and procedurally controlled by Fire Protection Engineering (FPE) personnel. The implementation of this system has resulted in significant cost savings and has minimized the allocation of resources necessary to ensure long term program viability.

Rispoli, R.D. [Entergy Operations, Russellville, AR (United States)

1996-07-01T23:59:59.000Z

316

Unsteady mixed convection in horizontal ducts with applications to chemical vapor deposition processes  

SciTech Connect (OSTI)

Mixed convection in a horizontal rectangular duct of aspect ratio 4 heated from below with cold side walls was studied numerically for a non-Boussinesq fluid. Results are presented for a reduced temperature of 2.33 and a Rayleigh number of 130,700. The resulting flow field at Re = 25 consisted of four steady longitudinal vortices, symmetric about the duct centerline, with a leading transverse roll cell. A reduction to Re = 10 resulted in the introduction of traveling transverse waves. A further reduction Re = 5 resulted in a loss of symmetry about the duct centerline plane. Further work is underway to verify the Re = 5 results.

Spall, R.E. [Univ. of South Alabama, Mobile, AL (United States). Dept. of Mechanical Engineering] [Univ. of South Alabama, Mobile, AL (United States). Dept. of Mechanical Engineering

1996-01-01T23:59:59.000Z

317

Comparative Study: CFD ?P Versus Measured ?P for 30% Flexible Ducts  

E-Print Network [OSTI]

foot-long circular ducts placed on both ends. A CFD model was built and simulations were run under different volumetric air flows. The static pressure drop for those conditions were analyzed and displayed. The final CFD model is tuned until...) computer model. Fluent 6.2.16 CFD software package was used to simulate the static pressure drop inside the flexible duct. 3-D computer model of 6 diameter flexible duct was generated for 30% compression in 5 ft. long. The laboratory data...

Ugursal, A.; Culp, C.

2006-01-01T23:59:59.000Z

318

Nonproliferation - Tell-tale seals | ornl.gov  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

SHARE SHARE Nonproliferation - Tell-tale seals Using an Oak Ridge National Laboratory technology, inspectors of containers of nuclear material will be able to know with unprecedented confidence whether an intruder has tampered with a seal. The system uses a light source of entangled photons to verify the continuity of a fiber-based seal, according to Travis Humble, who led the development team. Entanglement is a feature of quantum physics that describes how two spatially disparate systems exhibit strong correlations in otherwise independent behaviors. The work, sponsored by the Defense Threat Reduction Agency, is vital to ensure compliance with nonproliferation treaties because inspectors must confirm the uninterrupted containment and surveillance of any nuclear material.

319

Seal Beach, California: Energy Resources | Open Energy Information  

Open Energy Info (EERE)

Seal Beach, California: Energy Resources Seal Beach, California: Energy Resources (Redirected from Seal Beach, CA) Jump to: navigation, search Equivalent URI DBpedia Coordinates 33.7414064°, -118.1047866° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":33.7414064,"lon":-118.1047866,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

320

Microsoft Word - SealedSources - Cover.doc  

Broader source: Energy.gov (indexed) [DOE]

U.S. Department of Energy U.S. Department of Energy Office of Inspector General Office of Audit Services Audit Report Follow-up on the Management of Plutonium-239 Sealed Sources Recovery Activities OAS-M-06-09 September 2006 Department of Energy Washington, DC 20585 September 12, 2006 MEMORANDUM FOR MANAGER, LOS ALAMOS SITE OFFICE I &JJ;;C&$ . ( ' L / ? I ' < , ! FROM: . Collard ~ s s i s t a h t Inspector General for Performance Audits Office of Inspector General SUBJECT: INFORMATlON: Audit Report on "Follow- up on the Management of Plutonium-239 Sealed Sources Recovery Activities" The mission of the National Nuclear Security Administration's (NNSA) Off-site Recovery Project (OSRP) is to recover unwanted radioactive sealed sources (sources)

Note: This page contains sample records for the topic "aerosol-based duct sealing" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


321

Gas-path leakage seal for a turbine  

DOE Patents [OSTI]

A gas-path leakage seal for generally sealing a gas-path leakage-gap between spaced-apart first and second members of a turbine (such as combustor casing segments of a gas turbine). The seal includes a flexible and generally imperforate metal sheet assemblage having opposing first and second surfaces and two opposing raised edges extending a generally identical distance above and below the surfaces. A first cloth layer assemblage has a thickness generally equal to the previously-defined identical distance and is superimposed on the first surface between the raised edges. A second cloth layer assemblage is generally identical to the first cloth layer assemblage and is superimposed on the second surface between the raised edges. 5 figs.

Bagepalli, B.S.; Aksit, M.F.; Farrell, T.R.

1999-08-10T23:59:59.000Z

322

UL Press Release regarding E85 gaskets and seals  

Alternative Fuels and Advanced Vehicles Data Center [Office of Energy Efficiency and Renewable Energy (EERE)]

MEDIA CONTACT: MEDIA CONTACT: Joe Hirschmugl Global Media Relations Supervisor Underwriters Laboratories Phone: +1 847 830-1404 E-mail: Joseph.F.Hirschmugl@us.ul.com PRESS RELEASE Underwriters Laboratories now accepting certification investigation requests for gaskets and seals for use with E85 motor vehicle fuels UL on track to accept E85 dispenser products for testing by year-end 2007 NORTHBROOK, Ill. (Aug. 2, 2007) - Underwriters Laboratories (UL) announced today that it will accept requests for certification investigations for gaskets and seals for use with concentrated ethanol-blended fuels such as E85. In order to develop the requirements that will be used for certification, UL conducted a gasket and seal ethanol-blended fuel compatibility research program. The objective of this research was to subject various materials to a variety of test

323

Ceramic tube seals cut heat loss, achieve six month payback  

SciTech Connect (OSTI)

The methane reformer at the Celanese Chemical Company's Bishop, TX plant operates at approximately 1900/sup 0/F. The reformer has 32 tubes (9'' diameter) that pass through the firebox. Openings around the tubes measure 11'' in diameter to accommodate horizontal and vertical thermal expansion and movement as well as to facilitate tube removal. The gaps around the tubes permitted cool air to be drawn into the firebox (caused by slight negative pressure) and also allowed radiant heat to escape causing the reformer to operate at a lower than desired level of thermal efficiency. Celanese contracted to retrofit the old rigid firebrick roof in the methane reformer with a 10'' thick ceramic fiber module lining. The gaps around the tubes were sealed by using a special tube seal made from Nextel woven ceramic fiber fabric, a 1984 CHEMICAL PROCESSING Vaaler Award winner (Mid-November 1984, p.52). The Nextel fabric used in this application is a heat resistant textile that has a continuous use temperature of 2200/sup 0/F - well above the 1900/sup 0/F operating temperature of the reformer. The tube seals have been working exactly as intended, verified by observation through inspection ports. Temperatures in the penthouse area above the roof dropped from 240/sup 0/F to 150/sup 0/F. The reduction in heat losses has been attributed to the elimination of the gaps around each tube by the seals and to the improved K-factor of the ceramic module lining. The tube seals have paid for themselves within six months of installation. At that time, the seal boots were inspected and showed no signs of wear. With these results, the improved efficiency of the methane reformer promises to yield additional economic benefits.

Not Available

1985-11-01T23:59:59.000Z

324

Predicting the Performance of Edge Seal Materials for PV (Presentation)  

SciTech Connect (OSTI)

Edge seal materials were evaluated using a 100-nm film of Ca deposited on glass and laminated to another glass substrate. As moisture penetrates the package it converts the Ca metal to transparent CaOH2 giving a clear indication of the depth to which moisture has entered. Using this method, we have exposed test samples to a variety of temperature and humidity conditions ranging from 45C and 10% RH up to 85C and 85% RH, to ultraviolet radiation and to mechanical stress. We are able to show that edge seal materials are capable of keeping moisture away from sensitive cell materials for the life of a module.

Kempe, M.; Panchagade, D.; Dameron, A.; Reese, M.

2012-03-01T23:59:59.000Z

325

Effects of mineral fillers in slurry seal mixtures  

E-Print Network [OSTI]

. 48 2. 12 2. 19 2. 22 2. 23 1. 46 2. 12 2. 21 2. 25 2. 26 36. 8 9. 4 6. 4 5. 1 4. 7 37. 6 8. 6 5. 6 3. 8 3. 4 egased on computed maximum theoretical specific gravity ~ 2. 34 After compaction the specimens were measured for density... 1 Young Wet Track Abrasion Device. Page . 18 2 Aggregate Gradation. . 3 Mineral Piller Gradation. . 26 . 28 4 Sketch of Typical Specimen. . 5 Slurry Seal Test Specimen - Excellent 6 Slurry Seal Test Specimen - Unsatisfactory. . 7 Slurry...

Harper, William Joe

2012-06-07T23:59:59.000Z

326

Rotordynamic evaluation of hybrid damper seals with metal mesh elements  

E-Print Network [OSTI]

photograph of the test rig is shown in Figure 7. It consists of live main components: 1. the seal housing, 2. thc rotor, 3. the bearing support 4. the air turbine drive and 5. the electric motor, IIs , l& Figure 7t Photograph of the Rotating Test Rig... photograph of the test rig is shown in Figure 7. It consists of live main components: 1. the seal housing, 2. thc rotor, 3. the bearing support 4. the air turbine drive and 5. the electric motor, IIs , l& Figure 7t Photograph of the Rotating Test Rig...

Bhamidipati, Laxmi Narasimha Kameswara Sarma

2012-06-07T23:59:59.000Z

327

Window Spacers and Edge Seals in Insulating Glass Units: A State-of-the-Art Review and Future Perspectives  

E-Print Network [OSTI]

International) AG, TruSeal Technologies Edgetech GlasslamSeals, Science and Technology of Building Seals, Sealants,of Canada, Construction Technology Update no. 58 (2003) 1-4.

Bergh, Sofie Van Den

2014-01-01T23:59:59.000Z

328

Augmentation of Power Output of Axisymmetric Ducted Wind Turbines by Porous Trailing Edge Disks  

E-Print Network [OSTI]

This paper presents analytical and experimental results that demonstrated that the power output from a ducted wind turbine can be dramatically increased by the addition of a trailing edge device such as a porous disk. In ...

widnall, sheila

2014-06-30T23:59:59.000Z

329

DOE Zero Energy Ready Home Ducts in Conditioned Space Webinar (Text Version)  

Broader source: Energy.gov [DOE]

Below is a text version of the webinar titled "Design Strategies for Ducts in Conditioned Spaces," originally presented in March 2014 and part of DOE Challenge Home's Tech Training Webinar Series....

330

Turbulent mixing in ducts, theory and experiment application to aerosol single point sampling  

E-Print Network [OSTI]

straight duct, 900 elbow, 450 lateral and a generic mixer are incorporated into a correlation model for predicting the mixing quality for both the velocity and contaminant concentration as functions of such flow geometry, scale, pressure drop and fluid...

Langari, Abdolreza

2012-06-07T23:59:59.000Z

331

Ultrasonic Inspection of Tendon Ducts in Concrete Slabs Using 3D-SAFT  

Science Journals Connector (OSTI)

The main purpose to use ultrasonic pulse echo techniques for concrete are the following testing B;problems: Injections faults in tendon ducts because they lead to a loss of the...

M. Krause; W. Mller; H. Wiggenhauser

1997-01-01T23:59:59.000Z

332

Rotordynamics/discharge water-hammer coupling via seals in pump rotordynamics  

E-Print Network [OSTI]

is conducted in XLTRC2. Seal clearances and the reaction force angle are found to be important in shifting natural frequencies and damping. The sub-synchronous instability observed in field is duplicated successfully with double-clearance seals....

Zhang, Kaikai

2004-09-30T23:59:59.000Z

333

Exploring the mechanisms critical to the operation of metal face seals through modeling and experiments  

E-Print Network [OSTI]

This thesis aims to explore operation mechanisms of a special type of mechanical face seals: the flexible metal-to-metal face seal (FMMFS). Unique features of the FMMFS include much more flexibility in the circumferential ...

Wang, Yong, Ph. D. Massachusetts Institute of Technology, Dept. of Aeronautics and Astronautics

2008-01-01T23:59:59.000Z

334

Manufacturing of lab-on-a-chip devices : characterizing seals for on-board reagent delivery  

E-Print Network [OSTI]

The reagent delivery mechanism in a point-of-care, HIV diagnostic, microfluidic device is studied. Reagents held in an aluminum pack are released on the opening of a fluidic seal. Fluidic seals, controlling the flow of ...

Inamdar, Tejas Satish

2013-01-01T23:59:59.000Z

335

A Computational Study on the Leakage of Supercritical Carbon Dioxide through Labyrinth Seals  

E-Print Network [OSTI]

of turbomachinery equipment it is important to reduce internal leakage through seals. A computational study was performed to understand the leakage through seals subject to large pressure differential using Open source CFD software OpenFOAM. FIT (Fluid Property...

Pidaparti, Sandeep R

2013-11-26T23:59:59.000Z

336

Identification of dynamic force coefficients of a labyrinth and gas damper seal using impact load excitations  

E-Print Network [OSTI]

, and the seal displacement and acceleration time responses in two orthogonal directions are measured. A frequency domain parameter identification procedure allows the determination of the seals' dynamic force coefficients over a frequency range. Tests are made...

Ransom, David Lawrence

1997-01-01T23:59:59.000Z

337

Chip Seals for Asphalt Concrete Pavements: A Proposed Emulsion Residue Specification and Existing Pavement Texture Evaluation  

E-Print Network [OSTI]

Chip seals are a pavement surface treatment used for maintaining asphalt concrete pavements. National Cooperative Highway Research Program (NCHRP) Project 14-17 was performed to produce a national Chip Seal Manual which would consolidate the best...

Hoyt, Denise

2012-07-16T23:59:59.000Z

338

Design and modelling of a new form-fill-seal process  

E-Print Network [OSTI]

intermittent sealing mechanism pouch advance mechanism filling and air blowing mechanism control system 16 19 21 24 26 28 IV DESIGN PARAMETERS FOR A PROTOTYPE MACHINE 33 The The The The The The tube feeding mechanism continuous sealing... mechanism intermittent sealing mechanism pouch advance mechanism filling and air blowing mechanism control system 33 34 36 36 38 39 CHAPTER V MODELLING OF THE FORM-FILL-SEAL Page PROCESS COMPONENTS 45 The drive motor and feed back The strip...

Kalamdani, Rajeev Satyabodh

2012-06-07T23:59:59.000Z

339

Large scale test rig for flow visualization and leakage measurement of labyrinth seals  

E-Print Network [OSTI]

number. Heffner (1959) measured the leakage rates of air through stationary true size labyrinth seals with the goal of predicting leakage rates for new seal designs through correlation charts developed from his investigation. Leakage resistance... geometries and land surfaces with the objective of obtaining optimized seal design criteria. The test rig utilized a flat two-dimensional stationary seal with a radial clearance-to-width ratio of approximately 100:1 to reduce wall end effects. Air...

Broussard, Daniel Harold

2012-06-07T23:59:59.000Z

340

NOAA | AFSC | NMML Harbor Seals in Tidewater Glacial Fiords in  

E-Print Network [OSTI]

John Jansen National Marine Mammal Laboratory NOAA Fisheries Advance Notice of Proposed Rulemaking responded similarly J. K. Jansen et al. 2010. Reaction of harbor seals to cruise ships. Journal of Wildlife of ships May June July #12;NOAA | AFSC | NMML Space-Time Regression Model Ver Hoef, J. M., and J. K. Jansen

Note: This page contains sample records for the topic "aerosol-based duct sealing" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


341

INCREASED FOOD AND ENERGY CONSUMPTION OF LACTATING NORTHERN FUR SEALS,  

E-Print Network [OSTI]

respectively. Fish accounted for 66.4% of food biomass (69.4% of total energy consumption); squidINCREASED FOOD AND ENERGY CONSUMPTION OF LACTATING NORTHERN FUR SEALS, CALWRHINUS URSINUS MICHAEL A on ter- restrial mammals have specifically shown increased energy consumption by lactating females

342

EFFECTS OF NOISE ON SEALS AND SEA LIONS: LABORATORY APPROACHES  

E-Print Network [OSTI]

169 EFFECTS OF NOISE ON SEALS AND SEA LIONS: LABORATORY APPROACHES DAVID KASTAK Long Marine, and the evolutionary hiology of marine carnivores in general. Newer, more rapid technologies and psychophysical pinniped subjects reside at Long Marine Laboratory at the University of California, Santa Cruz, where

Reichmuth, Colleen

343

WIPP shaft seal system parameters recommended to support compliance calculations  

SciTech Connect (OSTI)

The US Department of Energy plans to dispose of transuranic waste at the Waste Isolation Pilot Plant (WIPP), which is sited in southeastern New Mexico. The WIPP disposal facility is located approximately 2,150 feet (650 m) below surface in the bedded halite of the Salado Formation. Prior to initiation of disposal activities, the Department of Energy must demonstrate that the WIPP will comply with all regulatory requirements. Applicable regulations require that contaminant releases from the WIPP remain below specified levels for a period of 10,000 years. To demonstrate that the WIPP will comply with these regulations, the Department of Energy has requested that Sandia National Laboratories develop and implement a comprehensive performance assessment of the WIPP repository for the regulatory period. This document presents the conceptual model of the shaft sealing system to be implemented in performance assessment calculations conducted in support of the Compliance Certification Application for the WIPP. The model was developed for use in repository-scale calculations and includes the seal system geometry and materials to be used in grid development as well as all parameters needed to describe the seal materials. These calculations predict the hydrologic behavior of the system. Hence conceptual model development is limited to those processes that could impact the fluid flow through the seal system.

Hurtado, L.D.; Knowles, M.K. [Sandia National Labs., Albuquerque, NM (United States); Kelley, V.A.; Jones, T.L.; Ogintz, J.B. [INTERA Inc., Austin, TX (United States); Pfeifle, T.W. [RE/SPEC, Inc., Rapid City, SD (United States)

1997-12-01T23:59:59.000Z

344

Duct Leakage Modeling in EnergyPlus and Analysis of Energy Savings from  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Duct Leakage Modeling in EnergyPlus and Analysis of Energy Savings from Duct Leakage Modeling in EnergyPlus and Analysis of Energy Savings from Implementing SAV with InCITeTM Title Duct Leakage Modeling in EnergyPlus and Analysis of Energy Savings from Implementing SAV with InCITeTM Publication Type Report LBNL Report Number LBNL-3525E Year of Publication 2010 Authors Wray, Craig P., and Max H. Sherman Publisher Lawrence Berkeley National Laboratory City Berkeley Keywords airflow, building, duct, energy, energy performance of buildings group, fan, hvac, indoor environment department, other, power, retrofits, simulation, system Abstract This project addressed two significant deficiencies in air-handling systems for large commercial building: duct leakage and duct static pressure reset. Both constitute significant energy reduction opportunities for these buildings. The overall project goal is to bridge the gaps in current duct performance modeling capabilities, and to expand our understanding of air-handling system performance in California large commercial buildings. The purpose of this project is to provide technical support for the implementation of a duct leakage modeling capability in EnergyPlus, to demonstrate the capabilities of the new model, and to carry out analyses of field measurements intended to demonstrate the energy saving potential of the SAV with InCITeTM duct static pressure reset (SPR) technology.A new duct leakage model has been successfully implemented in EnergyPlus, which will enable simulation users to assess the impacts of leakage on whole-building energy use and operation in a coupled manner. This feature also provides a foundation to support code change proposals and compliance analyses related to Title 24 where duct leakage is an issue. Our example simulations continue to show that leaky ducts substantially increase fan power: 10% upstream and 10% downstream leakage increases supply fan power 30% on average compared to a tight duct system (2.5% upstream and 2.5% downstream leakage). Much of this increase is related to the upstream leakage rather than to the downstream leakage. This does not mean, however, that downstream leakage is unimportant. Our simulations also demonstrate that ceiling heat transfer is a significant effect that needs to be included when assessing the impacts of duct leakage in large commercial buildings. This is not particularly surprising, given that "ceiling regain" issues have already been included in residential analyses as long as a decade ago (e.g., ASHRAE Standard 152); mainstream simulation programs that are used for large commercial building energy analyses have not had this capability until now. Our analyses of data that we collected during our 2005 tests of the SAV with InCITeTM duct static pressure reset technology show that this technology can substantially reduce fan power (in this case, by about 25 to 30%). Tempering this assessment, however, is that cooling and heating coil loads were observed to increase or decrease significantly depending on the time window used. Their impact on cooling and heating plant power needs to be addressed in future studies; without translating the coil loads to plant equipment energy use, it is not possible to judge the net impact of this SPR technology on whole-building energy use. If all of the loads had decreased, such a step would not be as necessary.

345

Leak-rate of seals: effective medium theory and comparison with experiment  

E-Print Network [OSTI]

Seals are extremely useful devices to prevent fluid leakage. We present an effective medium theory of the leak-rate of rubber seals, which is based on a recently developed contact mechanics theory. We compare the theory with experimental results for seals consisting of silicon rubber in contact with sandpaper and sand-blasted PMMA surfaces.

B. Lorenz; B. N. J. Persson

2009-11-16T23:59:59.000Z

346

Aquatic Mammals 2003, 29.2, 202213 Acoustic communication ranges for northern elephant seals  

E-Print Network [OSTI]

Aquatic Mammals 2003, 29.2, 202­213 Acoustic communication ranges for northern elephant seals communication range estimates for four northern elephant seal (Mirounga angustirostris) vocalization types and lower limit of auditory lter widths for the northern elephant seal auditory system. Signal de- tection

Reichmuth, Colleen

347

Effects of prolonged fasting on plasma cortisol and TH in postweaned northern elephant seal pups  

E-Print Network [OSTI]

Effects of prolonged fasting on plasma cortisol and TH in postweaned northern elephant seal pups of prolonged fasting on plasma cortisol and TH in postweaned northern elephant seal pups. Am J Physiol Reg- ulatory Integrative Comp Physiol 280: R790­R795, 2001.--Northern elephant seal (Mirounga angustirostris

Ortiz, Rudy M.

348

An introduction to API 682 shaft sealing for centrifugal and rotary pumps  

SciTech Connect (OSTI)

Seal failures in refineries represents between 5,000 and 10,000 dollars in maintenance costs. The lack of an industry standard approach has resulted in high-stocking cost, high maintenance costs, and complicated populations of seals. The API has offered API 682, Shaft Sealing Systems for Centrifugal and Rotary Pumps. This report discusses the benefits of API 682.

Dufour, J.W. [Amoco Oil Company, Chicago, IL (United States); Jones, R.L. [Shell Oil Company, Houston, TX (United States)

1994-11-01T23:59:59.000Z

349

PAHs And Parking Lots: A Field Study on PAHs Exported From Sealed and Unsealed Parking  

E-Print Network [OSTI]

2010 3.08 51.2 58.3 27.8 1.58 95.7 89.6 9.96 #12;10 4% of surface sealed 109-162 mg/kg (Gravel Wetland/kg (Bioretention) #12;Stormwater sediments (16PAH): Unsealed area sealed 100 mg/kg 100% sealed 1

350

3-D laser doppler velocimeter measurements of eccentric annular and labyrinth seals  

E-Print Network [OSTI]

as would be expected. Instead the maximum a)axial velocities are seen on the pressure side of the seals at the inlet but migrates to the suction side of the seal at the exit. The magnitude of this migration is dependent upon the seal eccentricity...

Das, Purandar Gururaj

1993-01-01T23:59:59.000Z

351

Rotary seal with enhanced lubrication and contaminant flushing  

DOE Patents [OSTI]

A resilient, ring shaped interference-type hydrodynamic rotary seal having waves on the lubricant side which provide increased film thickness and flushing action by creating contact pressure induced angulated restrictions formed by abrupt restrictive diverters. The angulated restrictions are defined by projecting ridges, corners at the trailing edge of the waves, or simply by use of a converging shape at the trailing edge of the waves which is more abrupt than the gently converging hydrodynamic inlet shape at the leading edge of the waves. The abrupt restrictive diverter performs two functions; a restricting function and a diverting function. The angulated restrictions cause a local film thickness restriction which produces a damming effect preventing a portion of the lubricant from leaking out of the dynamic sealing interface at the trailing edge of the wave, and results in a much thicker lubricant film thickness under the waves. This contributes to more film thickness in the remainder of the dynamic sealing interface toward the environment because film thickness tends to decay gradually rather than abruptly due to the relative stiffness of the seal material. Because of the angle of the abrupt restrictive diverter relative to the relative rotation direction, in conjunction with the restriction or damming effect, a strong diverting action is produced which pumps lubricant across the dynamic sealing interface toward the environment. The lubricant diversion is caused by the component of the rotational velocity tangent to the abrupt restrictive diverter. The component of rotational velocity normal to the abrupt restrictive diverter causes a portion of the lubricant film to be pumped past the abrupt restrictive diverter, thereby assuring adequate lubrication thereof.

Dietle, Lannie L. (Sugar Land, TX)

2000-01-01T23:59:59.000Z

352

An Investigation of the Integrity of Cemented Casing Seals with Application to Salt Cavern Sealing and Abandonment  

SciTech Connect (OSTI)

This research project was pursued in three key areas. (1) Salt permeability testing under complex stress states; (2) Hydraulic and mechanical integrity investigations of the well casing shoe through benchscale testing; and (3) Geomechanical modeling of the fluid/salt hydraulic and mechanical interaction of a sealed cavern.

Pfeifle, T.W.; Mellegard, K.D.; Skaug, N.T.; Bruno, M.S.

2001-04-19T23:59:59.000Z

353

"Interactions between Aegean Seals and Other Minoan-Mycenaean Art Forms"  

E-Print Network [OSTI]

-CLAUDE POURSAT BEIHEFT 5 Sceaux Minoens et Myc6niens Redaktion Walter Mriller INTERACTIONS BETWEEN AEGEAN SEALS AND OTHER MINOAN-MYCENAEAN ART FORMS JouN G. YouNcpR Most scholars use seals as comparanda, especially when discussing iconography. But few have.... HMs Heraklion Museum, sealing inventory no. NMA National Museum Athens, inventory no. ShGr Shaft Grave .] R A.Higgins, CIR 30, 1980, 161: "In spite of (seal-engraving's) small scale, this was the great Minoan art 2 J. Makkay, Early Starnp Seals...

Mycenaean

1995-01-01T23:59:59.000Z

354

Wafer-level packaging with compression-controlled seal ring bonding  

DOE Patents [OSTI]

A device may be provided in a sealed package by aligning a seal ring provided on a first surface of a first semiconductor wafer in opposing relationship with a seal ring that is provided on a second surface of a second semiconductor wafer and surrounds a portion of the second wafer that contains the device. Forcible movement of the first and second wafer surfaces toward one another compresses the first and second seal rings against one another. A physical barrier against the movement, other than the first and second seal rings, is provided between the first and second wafer surfaces.

Farino, Anthony J

2013-11-05T23:59:59.000Z

355

Theory versus experiment of the rotordynamic and leakage characteristics of smooth annular bushing oil seals  

E-Print Network [OSTI]

) ANGULAR CONTACT BALL BEARING TEST ROTOR HUB SEALINSERT SEAL HOUSING (END CAP) PRELOAD SPRING VACUUM SEAL ANNULAR BUSHING OIL-SEAL TEST RIG AIR TURBINE MOUNTING BASE HYDRAULIC SHAKER LOCATING SLEEVE MOUNTING BRACKET TEST OIL OUT LOCK NUT TEST... OIL OUT PULLEY AIR BUFFER SEAL AIR BUFFER SEAL 8 17,000 rpm. The test shaft is made from stainless steel and machined to a precise diameter of 116.84 mm [4.6 in ] at the test section. It is supported on the pedestals through angular contact ball...

Culotta, Vittorio G.

2005-02-17T23:59:59.000Z

356

A comparison of experimental and theoretical results for rotordynamic coefficients for labyrinth gas seals  

E-Print Network [OSTI]

. It provides answer s for the following questions: 1) How is the static position of the seal rotor controlled? 2) How is the dynamic motion of the rotor executed and contr oiled? 3) How is compressed air obtained and supplied to the apparatus, and how... is the pressure ratio acr oss the seal controlled? N) How is the incoming air prerotated before it enters the seal? 5) How are the seal rotor and stator mounted and replaced? 6) How is the seal rotor driven (rotated)? Recalling the rotordynamic...

Scharrer, Joseph Kirk

2012-06-07T23:59:59.000Z

357

Duct Leakage Modeling in EnergyPlus and Analysis of Energy Savings from Implementing SAV with InCITeTM  

E-Print Network [OSTI]

the impact of static pressure reset on HVAC system thermalHVAC control system varies the supply fan airflow to maintain a constant duct static pressure

Wray, Craig

2010-01-01T23:59:59.000Z

358

Investigating Low Temperature Properties of Rubber Seals - 13020  

SciTech Connect (OSTI)

To achieve the required tightness levels of containers for low and intermediate level radioactive wastes rubbers are widely applied as main sealing materials. The save encapsulation of the radioactive container contents has to be guaranteed according to legislation and appropriate guidelines for long storage periods as well as down to temperatures of -40 deg. C during transportation. Therefore the understanding of failure mechanisms that lead to leakage at low temperatures is of high importance. It is known that the material properties of rubbers are strongly influenced by temperature. At low temperatures this is caused by the rubber-glass transition (abbr. glass transition). During continuous cooling the material changes from rubber-like entropy-elastic to stiff energy-elastic behaviour, that allows nearly no strain or retraction. Therefore, rubbers are normally used above their glass transition but the minimum working temperature limit is not defined precisely, what can cause problems during application. The temperature range where full functionality is possible is strongly dependent on the application conditions and the material. For this investigation mainly ethylene propylene diene (EPDM) and fluorocarbon rubbers (FKM) were selected as they are often used for radioactive waste containers. Differential Scanning Calorimetry (DSC) and Dynamic Mechanical Analysis (DMA) are typically used for the determination of the temperature range of the glass transition process. The standardized compression set measurement according to ISO 815 is common for investigation of rubber sealing materials as the test simulates the seal behaviour after release. To reduce the test time of the standard tests a faster technique giving the same information was developed. Additionally, the breakdown temperature of the sealing function of complete O-ring seals is measured in a component test setup to compare it with the results of the other tests. The experimental setup is capable of measuring the leakage rate at low temperatures by the pressure rise method. A model was developed that allows calculating the minimum working temperature limit of a seal by combining the results of the applied methods. (authors)

Jaunich, M.; Wolff, D.; Stark, W. [BAM Federal Institute for Materials Research and Testing, Unter den Eichen 87, 12203 Berlin (Germany)] [BAM Federal Institute for Materials Research and Testing, Unter den Eichen 87, 12203 Berlin (Germany)

2013-07-01T23:59:59.000Z

359

High temperature performance evaluation of a hypersonic engine ceramic wafer seal  

SciTech Connect (OSTI)

Leakage rates of an innovative hypersonic engine seal were measured using a specially developed static high temperature seal test fixture at NASA Lewis Research Center. The three foot long structural panel-edge seal is designed to minimize leakage of high temperature, high pressure gases past the movable panels of advanced ramjet/scramjet engines. The seal is made of a stack of precision machined ceramic wafer pieces that are inserted into a closely conforming seal channel in the movable engine panel. The wafer seal accommodates the significant distortions in the adjacent engine walls through relative sliding between adjacent wafers. Seal leakage rates are presented for engine simulated air temperatures up to 1350F and for engine pressures up to 100 psi. Leakage rates are also presented for the seal, sealing both a flat wall condition, and an engine simulated distorted wall condition in which the distortion was 0.15 in. in only an 18 in. span. Seal leakage rates were low, meeting an industry-established tentative leakage limit for all combinations of temperature, pressure, and wall conditions considered. Comparisons are made between the measured leakage rates and leakage rates predicted using a seal leakage model developed from externally-pressurized gas film bearing theory.

Steinetz, B.M.

1991-04-01T23:59:59.000Z

360

RedSeal Comments on "Smart Grid RFI: Addressing Policy and Logistical  

Broader source: Energy.gov (indexed) [DOE]

RedSeal Comments on "Smart Grid RFI: Addressing Policy and RedSeal Comments on "Smart Grid RFI: Addressing Policy and Logistical Challenges. RedSeal Comments on "Smart Grid RFI: Addressing Policy and Logistical Challenges. RedSeal Comments on "Smart Grid RFI: Addressing Policy and Logistical Challenges. RedSeal's core technology is the ability to understand the access control of the network as a whole - not simply the behavior of a single device. RedSeal analyzes the interactions of firewalls, routers and load balancers network wide to determine the traffic allowed between every two points. RedSeal Comments on "Smart Grid RFI: Addressing Policy and Logistical Challenges. More Documents & Publications Southern Company: DOE Smart Grid RFI Addressing Policy and Logistical Challenges Association of Home Appliance Manufacturers Comments on Smart Grid RFI

Note: This page contains sample records for the topic "aerosol-based duct sealing" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


361

Compilation of current literature on seals, closures, and leakage for radioactive material packagings  

SciTech Connect (OSTI)

This report presents an overview of the features that affect the sealing capability of radioactive material packagings currently certified by the US Nuclear Regulatory Commission. The report is based on a review of current literature on seals, closures, and leakage for radioactive material packagings. Federal regulations that relate to the sealing capability of radioactive material packagings, as well as basic equations for leakage calculations and some of the available leakage test procedures are presented. The factors which affect the sealing capability of a closure, including the properties of the sealing surfaces, the gasket material, the closure method and the contents are discussed in qualitative terms. Information on the general properties of both elastomer and metal gasket materials and some specific designs are presented. A summary of the seal material, closure method, and leakage tests for currently certified packagings with large diameter seals is provided. 18 figs., 9 tabs.

Warrant, M.M.; Ottinger, C.A.

1989-01-01T23:59:59.000Z

362

Normal modes, virtual modes, and alternative representations in the theory of surface?duct sound propagation  

Science Journals Connector (OSTI)

This paper presents a theoretical study of sound propagation in an ocean?surface duct. It deals with several aspects of the theory from a point of view which has not heretofore been taken in the analyses of this problem. The model used to describe a duct assumes the ocean surface to be smooth and the square of the refractive index to be bilinear. Alternative representations of the sound field excited by a point source are derived the two playing the most significant role in this paper being the residue series and the normal?mode representation. It is shown that the depth functions of the residue series do not form a complete set as those of a normal?mode representation must and that the normal?mode spectrum is continuous rather than discrete. The completeness properties of the normal?mode functions are then utilized in a study of the energy?trapping capabilities of the duct. In this connection virtual modes are introduced and shown to lead naturally to the derivation of a leakage coefficient characteristic of the exponential leakage of energy out of the duct with increasing range. In addition a cutoff?frequency criterion useful in determining when a surface duct can trap energy is derived.

Frank M. Labianca

1973-01-01T23:59:59.000Z

363

Magical Seals, Secure Voting Machines, and Other Fantasies  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Magical Seals, Magical Seals, Secure Voting Machines, and Other Fantasies Roger G. Johnston, Ph.D., CPP Jon S. Warner, Ph.D. Vulnerability Assessment Team! Argonne National Laboratory! ! ! 630-252-6168 rogerj@anl.gov http://www.ne.anl.gov/capabilities/vat! Invited Talk for the Election Verification Network Meeting, Chicago, March 24-26, 2011 Argonne National Laboratory ~$738 million annual budget 1500 acres, 3400 employees, 4400 facility users, 1500 students R&D and technical assistance for government & industry Sponsors * DHS * DoD * DOS * IAEA * Euratom * DOE/NNSA * private companies * intelligence agencies * public interest organizations The VAT has done detailed vulnerability assessments on hundreds of different security

364

Turbocharger with variable nozzle having vane sealing surfaces  

DOE Patents [OSTI]

A variable nozzle for a turbocharger includes a plurality of vanes rotatably mounted on a nozzle ring and disposed in a nozzle flow path defined between the nozzle ring and an opposite nozzle wall. Either or both of the faces of the nozzle ring and nozzle wall include(s) at least one step that defines sealing surfaces positioned to be substantially abutted by airfoil surfaces of the vanes in the closed position of the vanes and to be spaced from the airfoil surfaces in positions other than the closed position. This substantial abutment between the airfoil surfaces and the sealing surfaces serves to substantially prevent exhaust gas from leaking past the ends of the airfoil portions. At the same time, clearances between the nozzle ring face and the end faces of the airfoil portions can be sufficiently large to prevent binding of the vanes under all operating conditions.

Arnold, Philippe (Hennecourt, FR); Petitjean, Dominique (Julienrupt, FR); Ruquart, Anthony (Thaon les Vosges, FR); Dupont, Guillaume (Thaon les Vosges, FR); Jeckel, Denis (Thaon les Vosges, FR)

2011-11-15T23:59:59.000Z

365

Low-temperature hermetic sealing of optical fiber components  

DOE Patents [OSTI]

A method for manufacturing low-temperature hermetically sealed optical fi components is provided. The method comprises the steps of: inserting an optical fiber into a housing, the optical fiber having a glass core, a glass cladding and a protective buffer layer disposed around the core and cladding; heating the housing to a predetermined temperature, the predetermined temperature being below a melting point for the protective buffer layer and above a melting point of a solder; placing the solder in communication with the heated housing to allow the solder to form an eutectic and thereby fill a gap between the interior of the housing and the optical fiber; and cooling the housing to allow the solder to form a hermetic compression seal between the housing and the optical fiber.

Kramer, Daniel P. (Centerville, OH)

1996-10-22T23:59:59.000Z

366

Low pressure cooling seal system for a gas turbine engine  

DOE Patents [OSTI]

A low pressure cooling system for a turbine engine for directing cooling fluids at low pressure, such as at ambient pressure, through at least one cooling fluid supply channel and into a cooling fluid mixing chamber positioned immediately downstream from a row of turbine blades extending radially outward from a rotor assembly to prevent ingestion of hot gases into internal aspects of the rotor assembly. The low pressure cooling system may also include at least one bleed channel that may extend through the rotor assembly and exhaust cooling fluids into the cooling fluid mixing chamber to seal a gap between rotational turbine blades and a downstream, stationary turbine component. Use of ambient pressure cooling fluids by the low pressure cooling system results in tremendous efficiencies by eliminating the need for pressurized cooling fluids for sealing this gap.

Marra, John J

2014-04-01T23:59:59.000Z

367

Hot compression process for making edge seals for fuel cells  

DOE Patents [OSTI]

A hot compression process for forming integral edge seals in anode and cade assemblies wherein the assemblies are made to a nominal size larger than a finished size, beads of AFLAS are applied to a band adjacent the peripheral margins on both sides of the assemblies, the assemblies are placed in a hot press and compressed for about five minutes with a force sufficient to permeate the peripheral margins with the AFLAS, cooled and cut to finished size.

Dunyak, Thomas J. (Blacksburg, VA); Granata, Jr., Samuel J. (South Greensburg, PA)

1994-01-01T23:59:59.000Z

368

Rotordynamic characteritics of incompressible-flow labyrinth seals  

E-Print Network [OSTI]

in labyrinth seals, neglecting the circumferential flow component. Kostyuk (1972) performed the first comprehensive analysis, but neglected the circumferential change in area due to the rotor eccentricity which is responsible for the relation between cross...-coupled forces as parallel rotor displacements take place. Iwatsubo (1980) considered a time dependent area change, but neglected the area derivative in the circumferential direction. Vance and Murphy (1980) extended Alford's analysis to compressible- flow...

Ghali, Anupama

1993-01-01T23:59:59.000Z

369

Status and conservation of Antarctic seals and seabirds: a review  

SciTech Connect (OSTI)

Present threats to Antarctic seabirds and seals when ashore include disturbance and habitat destruction and serious predation by introduced rats and cats at sub-Antarctic islands. In the marine environment threats are posed by pesticides (widespread but at low levels), pollution (mainly a potential problem associated with oil exploration), incidental takes and competition with commercial fisheries, which is reviewed in detail. Even in areas where harvesting of fish may be exceeding sustainable yield, predator-prey interaction data are inadequate to assess the level, or significance, of the effect on predators. Present krill harvests are small but likely to increase, especially in favored areas; species of potential vulnerability are noted. Existing legislation offers excellent protection for wildlife, but formally protected areas by no means cover the major breeding concentrations of seabirds and especially seals in all sectors and zones. There is a need for a comprehensive review, which in some areas will require extensive survey work. Programs for the control and elimination of alien predators need proper planning and major support. Marine reserves may be of limited benefit to pelagic seals and seabirds, and further research in some key areas is needed. Realistic environmental impact assessments will require more detailed information on predator distribution and movements than is available now; appropriate surveys and research need starting. Sensitive management of marine fisheries is difficult with the present level of quantitative data on predator-prey interactions. Difficulties in monitoring aspects of predator biology as indices of the state of prey stocks are reviewed.

Croxall, J.P.

1987-01-01T23:59:59.000Z

370

Cavitation erosion in blocked flow with a ducted ice-class propeller  

SciTech Connect (OSTI)

Ships that operate in ice often encounter momentary increased propeller cavitation because ice pieces block the flow into the propeller. For ducted propellers, this additional cavitation is more significant than it is for open propellers; ice pieces may become lodged against and within the duct and subject the propeller to longer periods of increased cavitation due to the blocked flow. Associated with this blocked flow is the possibility of cavitation erosion on the propeller. An erosion study, using paint films, was conducted in a cavitation tunnel with a model propeller of the type fitted to the Canadian Marine Drilling Ltd. vessel MV Robert LeMeur. A simulated ice blockage was installed ahead of the propeller model and within the duct. Tests were carried out over a range of advance coefficients for various test conditions. The resulting types of cavitation were documented, the erosion patterns were photographed and comparisons between each test were made.

Doucet, J.M.; Bose, N.; Walker, D. [Memorial Univ. of Newfoundland, St. John`s, Newfoundland (Canada). Ocean Engineering Research Centre; Jones, S.J. [National Research Council of Canada, St. John`s, Newfoundland (Canada). Inst. for Marine Dynamics

1996-12-31T23:59:59.000Z

371

Nuclear reactor fuel assembly duct-tube-to-inlet-nozzle attachment system  

DOE Patents [OSTI]

A reusable system for removably attaching the lower end 21 of a nuclear reactor fuel assembly duct tube to an upper end 11 of a nuclear reactor fuel assembly inlet nozzle. The duct tube's lower end 21 has sides terminating in locking tabs 22 which end in inwardly-extending flanges 23. The flanges 23 engage recesses 13 in the top section 12 of the inlet nozzle's upper end 11. A retaining collar 30 slides over the inlet nozzle's upper end 11 to restrain the flanges 23 in the recesses 13. A locking nut 40 has an inside threaded portion 41 which engages an outside threaded portion 15 of the inlet nozzle's upper end 11 to secure the retaining collar 30 against protrusions 24 on the duct tube's sides.

Christiansen, David W. (Kennewick, WA); Smith, Bob G. (Kennewick, WA)

1982-01-01T23:59:59.000Z

372

The development and application of the Remotely Monitored Sealing Array (RMSA).  

SciTech Connect (OSTI)

Advanced sealing technologies are often an integral part of a containment surveillance (CS) approach to detect undeclared diversion of nuclear materials. As adversarial capabilities continue to advance, the sophistication of the seal design must advance as well. The intelligent integration of security concepts into a physical technology used to seal monitored items is a fundamental requirement for secure containment. Seals have a broad range of capabilities. These capabilities must be matched appropriately to the application to establish the greatest effectiveness from the seal. However, many current seal designs and their application fail to provide the high confidence of detection and timely notification that can be appreciated with new technology. Additionally, as monitoring needs rapidly expand, out-pacing budgets, remote monitoring of low-cost autonomous sealing technologies becomes increasingly appealing. The Remotely Monitored Sealing Array (RMSA) utilizes this technology and has implemented cost effective security concepts establishing the high confidence that is expected of active sealing technology today. RMSA is a system of relatively low-cost but secure active loop seals for the monitoring of nuclear material containers. The sealing mechanism is a fiber optic loop that is pulsed using a low-power LED circuit with a coded signal to verify integrity. Battery life is conserved by the use of sophisticated power management techniques, permitting many years of reliable operation without battery replacement or other maintenance. Individual seals communicate by radio using a secure transmission protocol using either of two specially designated communication frequency bands. Signals are encrypted and authenticated by private key, established during the installation procedure, and the seal bodies feature both active and passive tamper indication. Seals broadcast to a central 'translator' from which information is both stored locally and/or transmitted remotely for review. The system is especially appropriate for nuclear material storage facilities, indoor or outdoor, enabling remote inspection of status rather than tedious individual seal verification, and without the need for interconnected cabling. A handheld seal verifier is also available for an inspector to verify any particular individual seal in close proximity. This paper will discuss the development of the RMSA sealing system, its capabilities, its application philosophy, and projected future trends.

Schoeneman, Barry Dale; Stein, Marius (Canberra, USA); Wishard, B. (International Atomic Energy Agency, Austria)

2010-09-01T23:59:59.000Z

373

Fundamental investigation of Duct/ESP phenomena: 1. 7 MW pilot parametric testing results  

SciTech Connect (OSTI)

Radian Corporation was contracted to investigate duct injection and electrostatic precipitator phenomena in a 1.7-MW pilot plant constructed for this test program. This study was an attempt to resolve previous problems and to answer remaining questions with the technology using an approach which concentrated on the fundamental mechanisms of the process. The goal of the study was to obtain a better understanding of the basic physical and chemical phenomena that control: (1) the desulfurization of flue gas by calcium-based reagent, and (2) the coupling of the duct injection process to an existing ESP particulate collection device. (VC)

McGuire, L.M.; Brown, C.A.

1991-07-22T23:59:59.000Z

374

Investigation of wall friction in noncircular ducts with a rough liner  

E-Print Network [OSTI]

phenomena in circular rough ducts and. these test data are discussed. 2. The test data of this research are similar to that shown by Nikuradse for fluid flow in pipes having artifi- cially roughened, inside surfaces. It is doubtful if Golebrook... in the relative roughness of the duct. The curves of Reynolds number versus friction factor are somewhat similar to those plotted by Nikuradse for fluid flow in artificially roughened round pipe. The shape of the curves is quite similar, but there is a...

Tyler, John Charles

2012-06-07T23:59:59.000Z

375

Heat transfer and pressure drop in square duct with two opposite repeated rib-roughened walls  

E-Print Network [OSTI]

HEAT TRANSFER AND PRESSURE DROP IN SQUARE DUCT WITH TWO OPPOSITE REPEATED RIB-ROUGHENED WALLS A Thesis CHIANG-KUO LEI Submitted to the Graduate College of Texas ARM University in partial fulfillment of the requirement for the degree of MASTER... OF SCIENCE December 1983 Major Subject: Mechanical Engineering HEAT TRANSFER AND PRESSURE DROP IN SQUARE DUCT WITH TWO OPPOSITE REPEATED RIB-ROUGHENED WALLS A Thesis by CHIANG-KUO LEI Approved as to style and content by: , ~p= jd~. = e-C in Han...

Lei, Chiang-Kuo

2012-06-07T23:59:59.000Z

376

Electric coheating as a means to test duct efficiency: A review and analysis of the literature  

SciTech Connect (OSTI)

Recent published literature on electric coheating was reviewed in order to assess its suitability for use in a method of test for the efficiency of residential duct systems. Electric coheating is the research use of electric heaters within the heated space to assess the thermal integrity of the building envelope. Information was sought in two primary areas: (1) experimental methodology and (2) accuracy of the coheating method. A variety of experimental variations was found, and the method was judged, on the basis of published data, to be capable of sufficient accuracy for use in duct testing.

Andrews, J.W.

1995-08-01T23:59:59.000Z

377

Nucleonic analysis of a preliminary design for the ETF neutral-beam-injector duct shielding  

SciTech Connect (OSTI)

A nucleonic analysis of the Engineering Test Facility Neutral-Beam-Injector duct shielding has been made using a hybrid Monte Carlo/discrete-ordinates method. This method used Monte Carlo to determine internal and external boundary surface sources for a subsequent discrete-ordinates calculation of the neutron and gamma-ray transport through the shield. The analysis also included determination of the energy and angular distribution of neutrons and gamma rays entering the duct from the torus plasma chamber. Confidence in the hybrid method and the results obtained were provided through a comparison with three-dimensional Monte Carlo results.

Urban, W.T.; Seed, T.J.; Dudziak, D.J.

1980-01-01T23:59:59.000Z

378

1736 IEEE TRANSACTIONS ON COMMUNICATIONS, VOL. 51, NO. 10, OCTOBER 2003 Impulse Response of the HVAC Duct as a  

E-Print Network [OSTI]

of the HVAC Duct as a Communication Channel Pavel V. Nikitin, Member, IEEE, Daniel D. Stancil, Senior Member (HVAC) ducts in buildings behave as multimode waveguides when excited at radio frequencies and thus, can of a usual indoor propagation channel. In this paper, we describe physical mechanisms which affect the HVAC

Hochberg, Michael

379

Building America Technology Solutions for New and Existing Homes: Buried and Encapsulated Ducts, Jacksonville, Florida (Fact Sheet)  

Broader source: Energy.gov [DOE]

In a study of three single-story houses in Florida, the Building America research team Consortium for Advanced Residential Buildings (CARB) investigated the strategy of using buried and/or encapsulated ducts (BED) to reduce duct thermal losses in existing homes.

380

Repository sealing plan for the Nevada Nuclear Waste Storage Investigations Project, fiscal years 1984 through 1990  

SciTech Connect (OSTI)

This report presents a plan to develop acceptable sealing methods for a prospective nuclear waste repository in unsaturated tuff in Yucca Mountain, which is on and adjacent to the Nevada Test Site. Sealing is the permanent closure of the underground facility, shafts, ramps, and boreholes. Questiona associated with the performance of the sealing system form the basis for this plan. Tasks that contribute to the resolution of these questions and support the documentation required for the construction authorization application are proposed. The approach to answering the performance-related questions is divided into six steps: (1) assess the need for sealing, (2) define the design requirements, (3) measure the material properties, (4) assess the performance of sealing designs, (5) perform laboratory analyses and field testing, and (6) reassess the performance of sealing designs. Organization of the tasks supporting each step is illustrated by detailed work-flow diagrams.

Fernandez, J.A.

1985-02-01T23:59:59.000Z

Note: This page contains sample records for the topic "aerosol-based duct sealing" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


381

The Development of Low-Cost Integrated Composite Seal for SOFC: Materials and Design Methodologies  

SciTech Connect (OSTI)

This report summarizes the work conducted by UConn SOFC seal development team during the Phase I program and no cost extension. The work included composite seal sample fabrication, materials characterizations, leak testing, mechanical strength testing, chemical stability study and acoustic-based diagnostic methods. Materials characterization work revealed a set of attractive material properties including low bulk permeability, high electrical resistivity, good mechanical robustness. Composite seal samples made of a number of glasses and metallic fillers were tested for sealing performance under steady state and thermal cycling conditions. Mechanical testing included static strength (pull out) and interfacial fracture toughness measurements. Chemically stability study evaluated composite seal material stability after aging at 800 C for 168 hrs. Acoustic based diagnostic test was conducted to help detect and understand the micro-cracking processes during thermal cycling test. The composite seal concept was successfully demonstrated and a set of material (coating composition & fillers) were identified to have excellent thermal cycling performance.

Xinyu Huang; Kristoffer Ridgeway; Srivatsan Narasimhan; Serg Timin; Wei Huang; Didem Ozevin; Ken Reifsnider

2006-07-31T23:59:59.000Z

382

IEEE TRANSACTIONS ON ANTENNAS AND PROPAGATION, VOL. 51, NO. 5, MAY 2003 945 Propagation Model for the HVAC Duct as a  

E-Print Network [OSTI]

for the HVAC Duct as a Communication Channel Pavel V. Nikitin, Member, IEEE, Daniel D. Stancil, Senior Member (HVAC) ducts in buildings are typically hollow metal pipes which can be used as waveguides to carry such a communication system. This paper presents a propagation model for a straight HVAC duct terminated at both ends

Stancil, Daniel D.

383

Rotordynamic coefficients and leakage flow of parallel-grooved liquid-seals  

E-Print Network [OSTI]

to account for the circumferential flow in the grooves. Childs' (1987) method for determining Hirs' empirical coefficients from static test data. for seals with smooth rotors and homogeneously roughened stators has been modified to be consistent... flow by roughening the stator surface. In addition, the rotor forces determined from seal analysis are effected by the circumferential grooves in the stator. From a rotordynamics viewpoint, seal analysis has the objective of predicting...

Kilgore, James Joseph

2012-06-07T23:59:59.000Z

384

Measure Guideline: Air Sealing Mechanical Closets in Slab-On-Grade Homes  

SciTech Connect (OSTI)

This measure guideline describes covers two fundamental retrofit strategies for air sealing around air handling systems that are located within the living space in an enclosed closet: one in which all of the equipment is removed and being replaced, and a closet where the equipment is to remain and existing conditions are sealed. It includes the design and installation details necessary to effectively seal the air handler closet and central return system to maximize the efficiency and safety of the space conditioning system.

Dickson, B.

2012-02-01T23:59:59.000Z

385

A new, efficient computational model for the prediction of fluid seal flowfields  

E-Print Network [OSTI]

labyrinth cavity inlet Mach number to the pressure drop for that particular cavity. SIM predicts the leakage within 3. 1 to 5. 2 % of the sir leakage measurements of Childs (1986). Although PRELIM and SIM both predict the leakage through seals quite... and radi6 velocity cells and (b) pressure cells. . . . . . . . . . . . 16 Schematic of labyrinth seal showing location of upstream, inlet, and downstream pressures, exit Mach number and upstream temperature 17 Generic seal showing distances...

Hibbs, Robert Irwin

1988-01-01T23:59:59.000Z

386

Toward a Better Understanding of Ducted Rotor Antitorque and Directional Control in Forward Flight  

E-Print Network [OSTI]

of the Core Automatic Flight Control System (CAFCS) mode. Figure 1 shows a sustained, large-amplitude 1-Hz yaw ABSTRACT Despite decades of very successful yaw-control and anti-torque applications, the aerodynamics dramatic. From a handling-qualities perspective, the ducted rotor provides the loads capacity required

387

Control of Flow Separation in S-ducts via Flow Injection and Suction  

E-Print Network [OSTI]

with minimum stagnation pressure losses at the compressor face. In some aircraft a straight inletT 1 Research of the curvature of the S-duct centerline lead to cross-stream centrifugal pressure gradients which cause distribution on the engine compressor face. The net effect of the secondary flow and of the diffuser adverse

Debiasi, Marco

388

Improving Building Envelope and Duct Airtightness of US Dwellings - the Current State of Energy Retrofits  

E-Print Network [OSTI]

of different types of multi-family buildings that is not= 6,710 Multi-Family WAP N = 1,340 Figure 1: Whole-buildingbuilding envelope and duct system airtightness of US single-family detached homes, manufactured homes, and multi-

Chan, Wanyu R.

2014-01-01T23:59:59.000Z

389

Simulations of detonation wave propagation in rectangular ducts using a three-dimensional WENO scheme  

SciTech Connect (OSTI)

This paper reports high resolution simulations using a fifth-order weighted essentially non-oscillatory (WENO) scheme with a third-order TVD Runge-Kutta time stepping method to examine the features of detonation front and physics in square ducts. The simulations suggest that two and three-dimensional detonation wave front formations are greatly enhanced by the presence of transverse waves. The motion of transverse waves generates triple points (zones of high pressure and large velocity coupled together), which cause the detonation front to become locally overdriven and thus form ''hot spots.'' The transversal motion of these hot spots maintains the detonation to continuously occur along the whole front in two and three dimensions. The present simulations indicate that the influence of the transverse waves on detonation is more profound in three dimensions and the pattern of quasi-steady detonation fronts also depends on the duct size. For a ''narrow'' duct (4L x 4L where L is the half-reaction length), the detonation front displays a distinctive ''spinning'' motion about the axial direction with a well-defined period. For a wider duct (20L x 20L), the detonation front exhibits a ''rectangular mode'' periodically, with the front displaying ''convex'' and ''concave'' shapes one following the other and the transverse waves on the four walls being partly out-of-phase with each other. (author)

Dou, Hua-Shu; Tsai, Her Mann [Temasek Laboratories, National University of Singapore (Singapore); Khoo, Boo Cheong; Qiu, Jianxian [Department of Mechanical Engineering, National University of Singapore (Singapore)

2008-09-15T23:59:59.000Z

390

Study of Gas Solid Flow Characteristics in Cyclone Inlet Ducts of A300Mwe CFB Boiler  

Science Journals Connector (OSTI)

Gas solid flow characteristics in cyclones inlet duct of a 300MW CFB boiler were studied in a cold circulating fluidized bed (CFB) experimental setup according to a 410t/h CFB boiler with a scale of 10?1....Figs...

J. Y. Tang; X. F. Lu; J. Lai; H. Z. Liu

2010-01-01T23:59:59.000Z

391

A COMPUTATIONAL AND EXPERIMENTAL ANALYSIS OF A DUCTED FAN USED IN VTOL UAV SYSTEMS  

E-Print Network [OSTI]

conditions. Fan rotor field including secondary flows, tip vortices, blade boundary layers and the wake sys wind tunnel test data. Total pressure measurements and computational predictions of mean flow field shows a significant level of 3D hub separation affecting the overall performance of the ducted fan

Camci, Cengiz

392

ASU nitrogen sweep gas in hydrogen separation membrane for production of HRSG duct burner fuel  

DOE Patents [OSTI]

The present invention relates to the use of low pressure N2 from an air separation unit (ASU) for use as a sweep gas in a hydrogen transport membrane (HTM) to increase syngas H2 recovery and make a near-atmospheric pressure (less than or equal to about 25 psia) fuel for supplemental firing in the heat recovery steam generator (HRSG) duct burner.

Panuccio, Gregory J.; Raybold, Troy M.; Jamal, Agil; Drnevich, Raymond Francis

2013-04-02T23:59:59.000Z

393

A numerical method for calculation of power output from ducted vertical axis hydro-current turbines  

Science Journals Connector (OSTI)

Abstract This paper investigates effects of ducting on power output from vertical axis hydro-current turbines. A numerical two-dimensional method based on the potential flow theory is developed for calculation of non-dimensional power output from these turbines. In this method, the blades are represented by vortex filaments. The vortex shedding from the blades is modeled by discrete vortices. A boundary element method is used to incorporate the duct shape which is represented by a series of panels with constant distributions of sources and doublets. The aerodynamic loading on the blades are calculated using a quasi-steady modeling. A time-marching scheme is used for implementation of the numerical method. The results of this method are compared with experimental results for a turbine model. A good correlation between the numerical and experimental results is obtained for tip speed ratios equal and higher than 2.25. However due to a lack of dynamic stall modeling, the numerical method is not able to predict power output accurately at lower tip speed ratios wherein effects of dynamic stall are significant. Both numerical and experimental results also showed that the power output from a turbine can increase significantly when it is enclosed within a well-designed duct. The maximum power output of the turbine model investigated in this paper showed a 74% increase when the turbine is operating within the duct relative to the case it is in free-stream conditions.

Mahmoud Alidadi; Sander Calisal

2014-01-01T23:59:59.000Z

394

Duct Leakage Impacts on Airtightness, Infiltration, and Peak Electrical Demand in Florida Homes  

E-Print Network [OSTI]

return leak from the attic can increase cooling electrical demand by 100%. Duct repairs in a typical. electrically heated Florida home reduce winter peak demand by about 1.6 kW per house at about one-sixth the cost of building new electrical generation...

Cummings, J. B.; Tooley, J. J.; Moyer, N.

1990-01-01T23:59:59.000Z

395

Balloon Dilatation of Salivary Duct Strictures: Report on 36 Treated Glands  

SciTech Connect (OSTI)

Purpose: This paper describes the technique for balloon dilatation of salivary duct strictures and evaluates the clinical and radiographic findings in a consecutive series of 36 affected glands. Methods: Thirty-four patients (36 glands) had balloon dilatation of their salivary duct strictures performed under fluoroscopic control. They were evaluated immediately afterwards and at review by sialography. Results: In 36 cases attempted, 33 (92%) strictures were dilated. The immediate post-treatment sialogram was available in 28 cases, of which 23 (82%) demonstrated complete and four (14%) partial elimination of stricture. In one case the appearance was unchanged(4%). Review data (mean 6.8 months) were available on 25 glands: 12 were asymptomatic (48%), 12 (48%) had reduced symptoms and one (4%)failed to improve. Sialographic data were available on 21 glands: in 10(48%) the duct remained patent, in one (5%) the stricture was partially eliminated, in seven (33%) the strictures had returned and in the remaining three (14%) cases there was complete obstruction. Conclusions: Balloon dilatation is an effective treatment of salivary duct stenosis. In half the cases the stricture recurred but symptomatic improvement was achieved and maintained in the majority of cases.

Drage, Nicholas A.; Brown, Jackie E. [Department of Dental Radiology, Guy's Dental Hospital, Guy's and St. Thomas' Hospital Trust, London (United Kingdom); Escudier, Michael P. [Department of Oral Medicine and Pathology, Guy's, King's and St. Thomas' Dental Institute, King's College, London (United Kingdom); Wilson, Ron F. [Dental Clinical Research, Guy's, King's and St. Thomas' Dental Institute, King's College, London (United Kingdom); McGurk, Mark [Department of Oral andMaxillofacial Surgery, Guy's, King's and St. Thomas' Dental Institute, King's College, London (United Kingdom)

2002-10-15T23:59:59.000Z

396

Design and Evaluation of a High Temperature Burner Duct Recuperator System  

E-Print Network [OSTI]

"The Babcock & Wilcox Company (B&W) has completed a program to design, construct, install, and field test a ceramic-based high-temperature burner-duct-recuperator (HTBDR) in an industrial setting. The unit was capable of operating in corrosive, high...

Parks, W. P.; DeBellis, C. L.; Kneidel, K.

397

Particle loading rates for HVAC filters, heat exchangers, and ducts Nomenclature  

E-Print Network [OSTI]

Particle loading rates for HVAC filters, heat exchangers, and ducts Nomenclature Afl surface area of floor (m2 ) bf fraction of bypass flow around the filter (dimensionless) Cout outdoor concentration on the filter per volume of air (mg/lm m3 ) Mf,tot total mass deposited on the filter per month of operation (g

Siegel, Jeffrey

398

Cooling air duct and screen arrangement for an air cooled engine  

SciTech Connect (OSTI)

This patent describes a cooling air duct and screen arrangement for an air cooled engine which includes an improved cooling air system for ensuring a supply of relatively clean air for ingestion by the cooling shroud, which consists of: a vertical transverse baffle mounted to the frame and fitting closely against a forward top portion of the shroud and having an edge shaped complementary to and disposed at least closely adjacent the hood. An air duct is mounted to the frame and has an upright rear wall seated against the front of the shroud in an area surrounding the inlet. The air duct further has an upright front wall and a connecting wall joining respective side and bottom edges of the front and rear walls and cooperating therewith to define an upwardly facing opening. A screen is located forwardly of the baffle and has a top and front joined by opposite sides with the top and opposite sides having rear edges mounted against the baffle and with the opposite sides and front having bottom edges engaged with the air duct about the upwardly facing opening wherein the screen is mounted solely to the baffle by connection means including a vertical guide means provided on the forward side of the baffle and flange means formed on the screen and being vertically slidably received in the guide means.

Hoch, J.J.; Stricker, D.K.

1986-03-04T23:59:59.000Z

399

Shielding design of the ITER NBI duct for nuclear and bremsstrahlung radiation  

Science Journals Connector (OSTI)

......evaluated about the nuclear heating rate and surface...representations of these nuclear responses are established...region and that in the vacuum vessel region. These...NBI duct wall in the nuclear fusion reactor. | Japan...Theoretical Particle Accelerators instrumentation Radiation......

S. Sato; H. Iida; M. Yamauchi; T. Nishitani

2005-12-20T23:59:59.000Z

400

seca-core-tech-sofc-seal-meeting | netl.doe.gov  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Core Technology Program - SOFC Seal Meeting July 8-9, 2003 Table of Contents Disclaimer Papers and Presentations Overviews Sandia Capabilities SBIR Projects IssuesRequirements...

Note: This page contains sample records for the topic "aerosol-based duct sealing" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


401

Experimental and numerical simulation of dissolution and precipitation: Implications for fracture sealing at Yucca Mountain, Nevada  

E-Print Network [OSTI]

FRACTURE SEALING AT YUCCA MOUNTAIN, NEVADA Patrick F. Dobsonpotential repository at Yucca Mountain, Nevada, would reducewas flowed through crushed Yucca Mountain tuff at 94C. The

Dobson, Patrick F.; Kneafsey, Timothy J.; Sonnenthal, Eric L.; Spycher, Nicolas; Apps, John A.

2001-01-01T23:59:59.000Z

402

REGULATION OF LIPID METABOLISM AND MILK LIPID CONTENT IN NORTHERN ELEPHANT SEALS.  

E-Print Network [OSTI]

??Animals that fast depend on mobilizing lipid stores to power metabolism. Northern elephant seals (Mirounga angustirostris) incorporate extended fasting into several life history stages: post (more)

Fowler, Melinda Anne

2012-01-01T23:59:59.000Z

403

Development of ultrananocrystalline diamond (UNCD) coatings for multipurpose mechanical pump seals.  

SciTech Connect (OSTI)

The reliability and performance of silicon carbide (SiC) shaft seals on multipurpose mechanical pumps are improved by applying a protective coating of ultrananocrystalline diamond (UNCD). UNCD exhibits extreme hardness (97 GPa), low friction (0.1 in air) and outstanding chemical resistance. Consequently, the application of UNCD coatings to multipurpose mechanical pump seals can reduce frictional energy losses and eliminate the downtime and hazardous emissions from seal failure and leakage. In this study, UNCD films were prepared by microwave plasma chemical vapor deposition utilizing an argon/methane gas mixture. Prior to coating, the SiC seals were subjected to mechanical polishing using different grades of micron-sized diamond powder to produce different starting surfaces with well-controlled surface roughnesses. Following this roughening process, the seals were seeded by mechanical abrasion with diamond nanopowder, and subsequently coated with UNCD. The coated seals were subjected to dynamic wear testing performed at 3600 RPM and 100 psi for up to 10 days during which the seals were periodically removed and inspected. The UNCD-coated seals were examined using Raman microanalysis, scanning electron microscopy, optical profilometry, and adhesion testing before and after the wear testing. These analyses revealed that delamination of the UNCD films was prevented when the initial SiC seal surface had an initial roughness >0.1 {micro}m. In addition, the UNCD surfaces showed no measurable wear as compared to approximately 0.2 {micro}m of wear for the untreated SiC surfaces.

Kovalchenko, A. M.; Elam, J. W.; Erdemir, A.; Carlisle, J. A.; Auciello, O.; Libera, J. A.; Pellin, M. J.; Gruen, D. M.; Hryn, J. N. (Materials Science Division); (Georgia Inst. of Tech.)

2011-01-01T23:59:59.000Z

404

A comparison of experimental and theoretical results for labyrinth gas seals with honeycomb stators  

E-Print Network [OSTI]

) Seal reaction-force magnitude (E) Direct and cross-coupled stifFness coefficients (F/L) Pitch of seal strips (L) Leakage mass flow rate (M/Lt) Friction coefficients Fluid pressure (F/Ls) Gss constant for air (L /Tts) Radius of control volumes I... parameters for the analysis, and they include: I) pressure ratio across the seal, 2) prerotation of the incoming 6uid, 3) seal con6guration, and 4) rotor rotational speed. Pressure Ratio The inlet air pressure and attendant mass 6ow rate through...

Hawkins, Lawrence Allen

2012-06-07T23:59:59.000Z

405

Reactive air brazing: A novel method of sealing SOFCs and other solid-state electrochemical devices  

SciTech Connect (OSTI)

High temperature electrochemical devices operate via an ion gradient that develops across a solid electrolyte; consequently, hermeticity across this membrane is paramount. Not only must the electrolyte contain no interconnected porosity, but it must be connected to device chassis with a gas-tight seal. Here we report a new method of brazing developed specifically for solid-state electrochemical applications. We demonstrate that the seal is hermetic and resistant to thermal aging, can be thermally cycled under rapid heating rates with no measurable loss in seal strength, and has shown promise in sealing full-size pSOFC components.

Weil, K. Scott; Kim, Jin Yong Y.; Hardy, John S.

2005-02-28T23:59:59.000Z

406

The Subsistence Harvest of Northern Fur Seals St. George Island in 2010  

E-Print Network [OSTI]

.................................................................................................................... 6 By-products and Waste..................................... 7 Heat Strokes seals harvested, b) incidence of by-products and waste during the harvest process, c) the occurrence

407

The Subsistence Harvest of Northern Fur Seals St. George Island in 2009  

E-Print Network [OSTI]

.................................................................................................................... 5 By-products and Waste..................................... 6 Heat Strokes seals harvested, b) incidence of by-products and waste during the harvest process, c) the occurrence

408

Elemental composition in sealed plutoniumberyllium neutron sources  

Science Journals Connector (OSTI)

Abstract Five sealed plutoniumberyllium (PuBe) neutron sources from various manufacturers were disassembled. Destructive chemical analyses for recovered PuBe materials were conducted for disposition purposes. A dissolution method for PuBe alloys was developed for quantitative plutonium (Pu) and beryllium (Be) assay. Quantitation of Be and trace elements was performed using plasma based spectroscopic instruments, namely inductively coupled plasma mass spectrometry (ICP-MS) and atomic emission spectrometry (ICP-AES). Pu assay was accomplished by an electrochemical method. Variations in trace elemental contents among the five PuBe sources are discussed.

N. Xu; K. Kuhn; D. Gallimore; A. Martinez; M. Schappert; D. Montoya; E. Lujan; K. Garduno; L. Tandon

2015-01-01T23:59:59.000Z

409

Tarmat behavior calculated for reservoir with sealing fault  

SciTech Connect (OSTI)

The Minagish Oolite oil reservoir in Kuwait is one of many Middle East reservoirs characterized by the presence of a tarmat (heavy to tar-like crude) at the oil-water contact. Since a waterflood project is planned for the Minagish Oolite, which contains a radial pattern of faults, a study was made to consider tarmat behavior upon water injection below it when the injection well is located near a sealing fault. The study resulted in a technique to predict the time of tarmat breakdown, response time at the nearest observation well, and differential pressure at the tarmat anywhere in the reservoir.

Osman, M.E.S.

1986-08-01T23:59:59.000Z

410

NETL: SECA Core Technology Program - SOFC Seal Meeting  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

SECA Core Technology Program - SOFC Seal Meeting SECA Core Technology Program - SOFC Seal Meeting July 8-9, 2003 Table of Contents Disclaimer Papers and Presentations Overviews Sandia Capabilities SBIR Projects Issues/Requirements Products Agenda [PDF-29KB] Participants [PDF-7KB] Disclaimer This report was prepared as an account of work sponsored by an agency of the United States Government. Neither the United States Government or any agency thereof, nor any of their employees, makes any warranty, express or implied, or assumes any legal liability or responsibility for the accuracy, completeness, or usefulness of any information, apparatus, product, or process disclosed, or represents that its use would not infringe privately owned rights. Reference herein to any specific commercial product, process, or service by trade name, trademark, manufacturer, or otherwise does not necessarily constitute or imply its endorsement, recommendation, or favoring by the United States Government or any agency thereof. The views and opinions of authors expressed herein do not necessarily state or reflect those of the United States Government or any agency thereof.

411

Mechanical properties and modeling of seal-forming lithologies  

SciTech Connect (OSTI)

Both rocksalt and shale lithologies are actively deformed in response to gravitational loads associated with deposition, and both form effective seals to petroleum and natural gas. Thus, the shapes of seal-forming units, and the nature of fractures and faults that may breach them depend upon either the mechanical properties of salt or those of shale, and the loading histories to which they have been subjected. The objectives of this research include the determination of the mechanical properties under controlled conditions of well-characterized shales, and the numerical modeling of rocksalt (and eventually shale) formations using laboratory-based rheologies. Progress has been made towards these goals over this project period, both in our experimental program on shale deformation and model development for the growth of salt diapirs. The mechanical anisotropy of an illite-bearing shale from Louisiana has been determined and related to the preferred orientation and distribution of clays. Its strength in the absence of pore fluids has been determined at confining pressures of up to 250 MPa and at high pressure we have investigated the effects of deformation rate and temperature. A numerical finite difference code has been developed to solve the incompressible Navier-Stokes equations and validated using a two- layer linear viscous model for which analytic solutions are available. Although the code has only been validated for the linear viscous case, it is capable of solving for highly nonlinear constitutive laws as well as solving for arbitrary interfaces between the salt and overburden.

Kronenberg, A.K.; Russell, J.E.; Carter, N.L.; Ibanez, W.; Mazariegos, R.

1992-04-01T23:59:59.000Z

412

Welding/sealing glass-enclosed space in a vacuum  

DOE Patents [OSTI]

A method of welding and sealing the edges of two juxtaposed glass sheets together to seal a vacuum space between the sheets comprises the steps of positioning a radiation absorbant material, such as FeO, VO.sub.2, or NiO, between the radiation transmissive glass sheets adjacent the edges and then irradiating the absorbant material, preferably with a laser beam, through at least one of the glass sheets. Heat produced by the absorbed radiation in the absorbant material melts glass in the portions of both glass sheets that are adjacent the absorbant material, and the melted glass from both sheets flows together to create the weld when the melted glass cools and hardens. The absorbant material can be dissolved and diffused into the melted glass to the extent that it no longer absorbs enough energy to keep the glass melted, thus, with appropriate proportioning of absorbant material to source energy power and welding heat needed, the process can be made self-stopping.

Tracy, C. Edwin (Golden, CO); Benson, David K. (Golden, CO)

1996-01-01T23:59:59.000Z

413

Changes in seal capacity of fractured claystone caprocks induced by dissolved and gaseous CO2 seepage  

E-Print Network [OSTI]

Changes in seal capacity of fractured claystone caprocks induced by dissolved and gaseous CO2; accepted 17 June 2008; published 31 July 2008. [1] Claystone caprocks are often the ultimate seal for CO2 underground storage when residual CO2 gas reaches the reservoir top due to buoyancy. Permeability changes

Luquot, Linda

414

Rotordynamic evaluation of frequency dependent impedances of hole-pattern gas damper seals  

E-Print Network [OSTI]

with an exit-to-inlet pressure ratio of 40 % and 54 %. Results of the tests show that the 3.18 mm hole-pattern seal has the highest average effective stiffness and lowest effective damping of all three seals. Results show that as cell depth increases, leakage...

Holt, Christopher George

2000-01-01T23:59:59.000Z

415

Development and validation of an analytical model for the notched pocket damper seal  

E-Print Network [OSTI]

. The PDS offers positive direct damping which increases with an increase in seal inlet pressure. The low stiffness of the test rig combined with the negative stiffness of the seal made it impracticable to conduct testing above inlet pressures of 64.7 psia...

Kannan Srinivas, Bharathwaj

2004-09-30T23:59:59.000Z

416

Production of glass or glass-ceramic to metal seals with the application of pressure  

DOE Patents [OSTI]

In a process for preparing a glass or glass-ceramic to metal seal comprising contacting the glass with the metal and heat-treating the glass and metal under conditions whereby the glass to metal seal is effected and, optionally, the glass is converted to a glass-ceramic, an improvement comprises carrying out the heat-treating step using hot isostatic pressing.

Kelly, Michael D. (West Alexandria, OH); Kramer, Daniel P. (Dayton, OH)

1987-11-10T23:59:59.000Z

417

Production of glass or glass-ceramic to metal seals with the application of pressure  

DOE Patents [OSTI]

In a process for preparing a glass or glass-ceramic to metal seal comprising contacting the glass with the metal and heat-treating the glass and metal under conditions whereby the glass to metal seal is effected and, optionally, the glass is converted to a glass-ceramic, an improvement comprises carrying out the heat-treating step using hot isostatic pressing.

Kelly, M.D.; Kramer, D.P.

1985-01-04T23:59:59.000Z

418

Grey seal distribution and abundance in North Wales, 2002-2003  

E-Print Network [OSTI]

i Grey seal distribution and abundance in North Wales, 2002-2003 Westcott, S.M. & Stringell, T.B. Stringell Title: "Grey seal distribution and abundance in North Wales, 2002-2003" Authors: Westcott, S Library x1 C. Duck, SMRU x1 Joe Breen EHS x1 PML, Library, Plymouth x1 S. Westcott x5 M. Baines x1 S

Bearhop, Stuart

419

Grey seal pup production for North Wales, Westcott, S.M. & Stringell, T.B.  

E-Print Network [OSTI]

Grey seal pup production for North Wales, 2002 Westcott, S.M. & Stringell, T.B. Marine Monitoring.B. Stringell Title: "Grey seal pup production for North Wales, 2002" Authors: Westcott, S.M. & Stringell, T S. Westcott x5 M. Baines x1 S. Stansfield, Bardsey Bird Observatory x1 A. Moralee, RSPB South Stack

Bearhop, Stuart

420

A description and status of the Yucca Mountain Project repository sealing program  

SciTech Connect (OSTI)

Yucca Mountain is being characterized to determine its suitability as a site for a high-level nuclear waste repository. The repository would be located in the unsaturated zone in fractured, welded tuff. Sealing of the repository is one element of the Yucca Mountain Project (YMP). This paper presents a description of the repository sealing program including the sealing design options, design requirements, design constraints, and the identification of the proposed sealing materials and field tests. Design options for the shafts include anchor-to-bedrock seals, shaft fill, and settlement plugs; in the underground facility options include drift seals, drainage channels, sumps, and bulkheads. Design requirements are those quantitative requirements imposed on the sealing design options to achieve a desired level of performance. Constraints are restrictions placed on the repository design by the sealing design. As (1) additional hydrogeologic data are obtained through site characterization, (2) approaches to allocating performance to various subsystems within the YMP are refined, and (3) the exploratory shafts and the associated testing results are developed, the design requirements and constraints may be modified and used in developing the License Application Design. 1 ref., 1 fig.

Fernandez, J.A.; Hinkebein, T.E.

1989-10-01T23:59:59.000Z

Note: This page contains sample records for the topic "aerosol-based duct sealing" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


421

In-air and underwater hearing sensitivity of a northern elephant seal (Mirounga angustirostris)  

E-Print Network [OSTI]

In-air and underwater hearing sensitivity of a northern elephant seal (Mirounga angustirostris) D for a female northern elephant seal (Mirounga angustirostris). Hearing sensitivity in air was generally poor. Kastak and R.J. Schusterman Abstract: In-air and underwater sound detection thresholds were obtained

Reichmuth, Colleen

422

Thermal Cyclability of Reactive Air Braze Seals in Anode Supported Solid Oxide Fuel Cells  

SciTech Connect (OSTI)

The popularity of anode-supported solid oxide fuel cells (SOFC) has increased in tandem with the ability to fabricate thinner gas-tight yttrium-stabilized zirconia (YSZ) electrolyte layers, which can now be routinely produced on the order of 7 to 10 ?m thick. While this has significantly improved power output and decreased the required fuel cell operating temperatures, the ability to reliably seal fuel cells remains a concern. The seals must be hermetic and be robust enough to retain their hermeticity even under the extreme operating conditions of SOFCs. Perhaps the largest contributor to stresses experienced by the seal is the fact that the SOFC is an assembly of many different materials with different thermal expansion properties. Although every effort is made to minimize thermal expansion mismatches across the seals, the stresses developed during thermal cycling still jeopardize seal integrity. Reactive air brazing (RAB), a method of joining that employs a metallic, and therefore non-brittle, seal material has been used to seal electrolyte/anode bilayers, such as those in anode-supported SOFCs, to Crofer-22 alloy. The results of rupture strength testing will be reported for as-brazed and thermally cycled samples and the effect of thermal cycling on the RAB seal microstructure will be shown

Hardy, John S.; Darsell, Jens T.; Coyle, Christopher A.; Birnbaum, Jerome C.; Weil, K. Scott

2004-12-31T23:59:59.000Z

423

Dynamic pressure and shear stress measurements on the stator wall of whirling annular seals  

E-Print Network [OSTI]

Dynamic pressure and shear stress measurements on the stator wall of whirling annular seals are presented. Two flow conditions (Re=12,000 & 24,000), two seal speeds (Ta=3,300 & 6,600) and three eccentricity ratios (0, 10, & 50% of the clearance...

Winslow, Robert Bradley

1994-01-01T23:59:59.000Z

424

Analysis of Instabilities and Their Impact on Friction Factor in Hole-Pattern Seals  

E-Print Network [OSTI]

The determination of the leakage and consequently the friction factor is an important part of analyzing the flow through a seal. This is done experimentally by means of a flat plate tester, which allows for the simplified representation of the seal...

Sekaran, Aarthi 1985-

2012-11-21T23:59:59.000Z

425

Current Situation for Management of Disused Sealed Radioactive Sources in Japan - 13025  

SciTech Connect (OSTI)

As for the Sealed Radioactive Source currently used in Japan, many of them are imported from overseas. The U.S., Canada, Germany, the Netherlands, Belgium and Czech Republic are the main exporting States. Many of disused sealed radioactive sources are being returned to exporting States. The sealed radioactive sources which cannot be returned to exporting States are appropriately kept in the domestic storage facility. So, there are not main problem on the long term management of disused sealed radioactive sources in Japan. However, there are some difficulties on repatriate. One is reservation of a means of transport. The sea mail which conveys radioactive sources owing to reduction of movement of international cargo is decreasing in number. And there is a denial of shipment. Other one is that the manufacturer has already resigned from the work and cannot return disused sealed radioactive sources, or a manufacturer cannot specify and disused sources cannot be returned. The disused sealed radioactive source which cannot be repatriated is a little in term of radioactivity. As for the establishment of national measure of final disposal facility for disused sealed radioactive sources, in Japan, it is not yet installed with difficulty. Since there are many countries for which installation of a final disposal facility for disused sealed radioactive sources is difficult, the source manufacture country should respond positively to return the source which was manufactured and sold in the past. (authors)

Kusama, Keiji; Miyamoto, Yoichi [Japan Radioisotope Association, Radiopharmaceutical and Radioisotope Supply Business Promotion Department (Japan)] [Japan Radioisotope Association, Radiopharmaceutical and Radioisotope Supply Business Promotion Department (Japan)

2013-07-01T23:59:59.000Z

426

Follow-up on the Management of Plutonium-239 Sealed Sources Recovery  

Broader source: Energy.gov (indexed) [DOE]

Follow-up on the Management of Plutonium-239 Sealed Sources Follow-up on the Management of Plutonium-239 Sealed Sources Recovery Activities, OAS-M-06-09 Follow-up on the Management of Plutonium-239 Sealed Sources Recovery Activities, OAS-M-06-09 The mission of the National Nuclear Security Administration's (NNSA) Off-site Recovery Project (OSRP) is to recover unwanted radioactive sealed sources (sources) held in the piblic sector. thereby reducing the threat of the sources being used in radiological dispersal de\iices or a "dirty bomb." Plutonium-239 (Pu-239), one of the rildioactive sealed sources recovered by OSRP, requires additional safeguards because ~t is a special nuclear material. These sources were manufactured in the United States (Li S.) and loaned or leased to colleges and universilies, commercial

427

The State-of-the-Art in Sealing Technology for Solid Oxide Fuel Cells  

SciTech Connect (OSTI)

One of the keys to developing viable solid oxide fuel cell (SOFC) systems is to first develop reliable and inexpensive stack sealing technology. Three general approaches are currently being pursued, including: rigid bonded sealing, compressive sealing, and compliant bonded sealing. This review highlights the advantages and limitations of each option, discusses some of the leading concepts, and outlines the future steps that need to be taken in their development. Given the number of different SOFC stack designs under development, the variety of potential applications/conditions in which these systems can be used, and the complexities of stack manufacture, it is likely that no one sealing technique will be suitable for all uses. Therefore continued progress in each general area, as well as the development of new concepts, is critical to the eventual success of SOFC technology.

Weil, K. Scott

2006-08-01T23:59:59.000Z

428

Seal inlet disturbance boundary conditions for rotordynamic models and influence of some off-design conditions on labyrinth rotordynamic instability  

E-Print Network [OSTI]

the swirl slip velocity. The benefits of using the new seal-inlet boundary condition correlations were assessed by implementing them into a CFD-perturbation model. Consistently improved agreement with measurements was obtained for both liquid annular seals...

Xi, Jinxiang

2007-04-25T23:59:59.000Z

429

PRELIMINARY REPORT: EFFECTS OF IRRADIATION AND THERMAL EXPOSURE ON ELASTOMERIC SEALS FOR CASK TRANSPORTATION AND STORAGE  

SciTech Connect (OSTI)

A testing and analysis approach to predict the sealing behavior of elastomeric seal materials in dry storage casks and evaluate their ability to maintain a seal under thermal and radiation exposure conditions of extended storage and beyond was developed, and initial tests have been conducted. The initial tests evaluate the aging response of EPDM elastomer O-ring seals. The thermal and radiation exposure conditions of the CASTOR V/21 casks were selected for testing as this cask design is of interest due to its widespread use, and close proximity of the seals to the fuel compared to other cask designs leading to a relatively high temperature and dose under storage conditions. A novel test fixture was developed to enable compression stress relaxation measurements for the seal material at the thermal and radiation exposure conditions. A loss of compression stress of 90% is suggested as the threshold at which sealing ability of an elastomeric seal would be lost. Previous studies have shown this value to be conservative to actual leakage failure for most aging conditions. These initial results indicate that the seal would be expected to retain sealing ability throughout extended storage at the cask design conditions, though longer exposure times are needed to validate this assumption. The high constant dose rate used in the testing is not prototypic of the decreasingly low dose rate that would occur under extended storage. The primary degradation mechanism of oxidation of polymeric compounds is highly dependent on temperature and time of exposure, and with radiation expected to exacerbate the oxidation.

Verst, C.; Skidmore, E.; Daugherty, W.

2014-05-30T23:59:59.000Z

430

A comparison of experimental results and theoretical predictions for the rotordynamic coefficients of short (L/D = 1/6) labyrinth seals  

E-Print Network [OSTI]

CLEARANCE (mm) SEAL CLEARANCE (mm) Figure 11. Inlet tangential velocity vs. seal clearance for teeth-on-stator and teeth-on-rotor seals. 28 Swirl = 1 Pra 0. 45 tc =12000 cpm 0. 20 + 0. 18 A ~ 0. 1S E 014 D. 12 O 0. 10 M 0. 08 0. 08 1 = seal gl... CLEARANCE (mm) SEAL CLEARANCE (mm) Figure 11. Inlet tangential velocity vs. seal clearance for teeth-on-stator and teeth-on-rotor seals. 28 Swirl = 1 Pra 0. 45 tc =12000 cpm 0. 20 + 0. 18 A ~ 0. 1S E 014 D. 12 O 0. 10 M 0. 08 0. 08 1 = seal gl...

Pelletti, Joseph Michael

2012-06-07T23:59:59.000Z

431

Automated Sealing of Home Enclosures with Aerosol Particles  

Broader source: Energy.gov (indexed) [DOE]

October 14, 2011 October 14, 2011 Automated Sealing of Home Enclosures with Aerosol Particles Welcome to the Webinar! We will start at 11:00 AM Eastern Time Be sure that you are also dialed into the telephone conference call: Dial-in number: 888-989-7679; Pass code: 3599368 Download the presentation at: www.buildingamerica.gov/meetings.html Building Technologies Program eere.energy.gov Building America: Introduction October 14, 2011 Chuck Booten Chuck.booten@nrel.gov Building Technologies Program Building Technologies Program eere.energy.gov * Reduce energy use in new and existing residential buildings * Promote building science and systems engineering / integration approach * "Do no harm": Ensure safety, health and durability are maintained or improved

432

Acoustic Inspection and Analysis of Liquids in Sealed Containers  

SciTech Connect (OSTI)

This article describes the Acoustic Inspection Device (AID) developed by PNNL which uses acoustic to determine the contents and fill level of sealed containers. AID is a power drill shaped battery operated device fitted with a transducer that sends an ultrasonic pusle through a container of liquid and measure the return echo. The device compares the echo velocity and attnuation and compares that data to a materials database in an Palm Pilot vlecored to the top of the device to give the operator a text identification of the substance with 5 seconds. The device is sensitive enough to distinguish coke from diet coke and and can distinguish subtances at a variety of temperatures ranging from below freezing to over 100degreesF. PNNL won an R&D 100 award for the technology in 2003.

Diaz, Aaron A.

2003-12-01T23:59:59.000Z

433

Reducing Thermal Losses and Gains With Buried and Encapsulated Ducts in Hot-Humid Climates  

SciTech Connect (OSTI)

The Consortium for Advanced Residential Buildings (CARB) monitored three houses in Jacksonville, FL, to investigate the effectiveness of encapsulated and encapsulated/buried ducts in reducing thermal losses and gains from ductwork in unconditioned attics. Burying ductwork beneath loose-fill insulation has been identified as an effective method of reducing thermal losses and gains from ductwork in dry climates, but it is not applicable in humid climates where condensation may occur on the outside of the duct jacket. By encapsulating the ductwork in closed cell polyurethane foam (ccSPF) before burial beneath loose-fill mineral fiber insulation, the condensation potential may be reduced while increasing the R-value of the ductwork.

Shapiro, C.; Magee, A.; Zoeller, W.

2013-02-01T23:59:59.000Z

434

Impacts of Optimized Cold & Hot Deck Reset Schedules on Dual Duct VAV Systems - Theory and Model Simulation  

E-Print Network [OSTI]

Impacts of Optimized Cold & Hot Deck Reset Schedules on Dual Duct VAV Systems - Theory and Model Simulation Mingsheng Liu, Ph.D., P.E. Energy Systems Laboratory Texas A&M University College Station, Texas Abstract Optimal hot and cold deck... rate increased from 30% to 70% of the maximum flow. Introduction Simultaneous heating and cooling can be reduced sigmficantly by optimizing cold and hot deck reset schedules in dual duct constant volume systems [Liu et. a1 1994, 1995, 19961...

Liu, M.; Claridge, D. E.

1998-01-01T23:59:59.000Z

435

Instrumented elephant seals reveal the seasonality in chlorophyll and light-mixing regime in the iron-fertilized Southern Ocean  

E-Print Network [OSTI]

Instrumented elephant seals reveal the seasonality in chlorophyll and light-mixing regime and salinity provided by sensors mounted on the elephant seals of Kerguelen Island. Our results were mainly. Xing, H. Claustre, and C. Guinet (2013), Instrumented elephant seals reveal the seasonality

Claustre, Hervé

436

Continuous Commissioning of a Single Fan Dual Duct System in an Office Building  

E-Print Network [OSTI]

Continuous Commissioning of a Single Fan Dual Duct System in an Office Building D. Dong M. Liu, Ph.D., P.E Jinrong Wang, P.E Energy Systems Laboratory Energy Systems Laboratory... of AHU control sequences can significantly improve building comfort and reduce HVAC energy cost. REFERENCES 1. Liu, M., Y. Zhu, and D. E. Claridge, Use of EMCS Recorded Data to Identify Potential Savings Due to Improved HVAC Operations...

Dong, D.; Liu, M.

2005-01-01T23:59:59.000Z

437

Optimize the Supply Air Temperature Reset Schedule for a Single-Duct VAV System  

E-Print Network [OSTI]

Optimize the Supply Air Temperature Reset Schedule for a Single-Duct VAV System Guanghua Wei Mingsheng Liu, Ph.D., P.E. David E. Claridge, Ph.D., P.E. Senior Research Associate Associate Professor Professor Energy Systems Lab Architectural... will occur once the alrflow reaches the minimum and the heating load increases. To minimize this simultaneous cooling and heating, the supply air temperature is often reset based on either return air temperature or outside air temperature. Liu et al...

Wei, G.; Claridge, D. E.; Liu, M.

2000-01-01T23:59:59.000Z

438

Hot-film anemometer measurements in adiabatic two-phase flow through a vertical duct  

SciTech Connect (OSTI)

A hot-film anemometer (HFA) probe was used to obtain local measurements of void fraction and bubble frequency in a vertically oriented, high aspect ratio duct containing R-134a under selected adiabatic two-phase flow conditions. Data were obtained along a narrow dimension scan over the range 0.03 {le} {bar Z} {le} 0.80, where {bar Z} is the distance from the wall normalized with the duct spacing dimension. The void fraction profiles displayed large gradients in the near-wall regions and broad maxima near the duct centerline. The trends in the bubble frequency data generally follow those for the local void fraction data. However, the relatively large number of bubbles at higher pressure implies a larger magnitude of the interfacial area concentration, for the same cross-sectional average void fraction. For the two annular flow conditions tested, analysis of the HFA output voltage signal enabled identification of three distinct regions of the flow field; liquid film with dispersed bubbles, interfacial waves, and continuous vapor with dispersed droplets.

Trabold, T.A.; Moore, W.E.; Morris, W.O. [Lockheed Martin Corp., Schenectady, NY (United States)

1997-06-01T23:59:59.000Z

439

CONTRACTORS STATE LICENSE BOARD 9821 Business Park Drive, Sacramento, CA 95827 STATE OF CALIFORNIA  

E-Print Network [OSTI]

, and require enhanced duct sealing, proper refrigerant charge, airflow, and fan watt draw. As you know

440

Case studies of sealing methods and materials used in the salt and potash mining industries  

SciTech Connect (OSTI)

Sealing methods and materials currently used in salt and potash industries were surveyed to determine if systems analogous to the shaft seal design proposed for the Waste Isolation Pilot Plant (WIPP) exist. Emphasis was first given to concrete and then expanded to include other materials. Representative case studies could provide useful design, construction, and performance information for development of the WIPP shaft seal system design. This report contains a summary of engineering and construction details of various sealing methods used by mining industries for bulkheads and shaft liners. Industrial experience, as determined from site visits and literature reviews, provides few examples of bulkheads built in salt and potash mines for control of water. Sealing experiences representing site-specific conditions often have little engineering design to back up the methods employed and even less quantitative evaluation of seal performance. Cases examined include successes and failures, and both contribute to a database of experiences. Mass salt-saturated concrete placement under ground was accomplished under several varied conditions. Information derived from this database has been used to assess the performance of concrete as a seal material. Concrete appears to be a robust material with successes in several case studies. 42 refs.

Eyermann, T.J.; Sambeek, L.L. Van [RE/SPEC Inc., Rapid City, SD (United States); Hansen, F.D. [Sandia National Labs., Albuquerque, NM (United States). Repository Isolation Systems Dept.

1995-11-01T23:59:59.000Z

Note: This page contains sample records for the topic "aerosol-based duct sealing" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


441

A strategy to seal exploratory boreholes in unsaturated tuff; Yucca Mountain Site Characterization Project  

SciTech Connect (OSTI)

This report presents a strategy for sealing exploratory boreholes associated with the Yucca Mountain Site Characterization Project. Over 500 existing and proposed boreholes have been considered in the development of this strategy, ranging from shallow (penetrating into alluvium only) to deep (penetrating into the groundwater table). Among the comprehensive list of recommendations are the following: Those boreholes within the potential repository boundary and penetrating through the potential repository horizon are the most significant boreholes from a performance standpoint and should be sealed. Shallow boreholes are comparatively insignificant and require only nominal sealing. The primary areas in which to place seals are away from high-temperature zones at a distance from the potential repository horizon in the Paintbrush nonwelded tuff and the upper portion of the Topopah Spring Member and in the tuffaceous beds of the Calico Hills Unit. Seals should be placed prior to waste emplacement. Performance goals for borehole seals both above and below the potential repository are proposed. Detailed construction information on the boreholes that could be used for future design specifications is provided along with a description of the environmental setting, i.e., the geology, hydrology, and the in situ and thermal stress states. A borehole classification scheme based on the condition of the borehole wall in different tuffaceous units is also proposed. In addition, calculations are presented to assess the significance of the boreholes acting as preferential pathways for the release of radionuclides. Design calculations are presented to answer the concerns of when, where, and how to seal. As part of the strategy development, available technologies to seal exploratory boreholes (including casing removal, borehole wall reconditioning, and seal emplacement) are reviewed.

Fernandez, J.A. [Sandia National Labs., Albuquerque, NM (United States); Case, J.B.; Givens, C.A.; Carney, B.C. [IT Corp., Albuquerque, NM (United States)

1994-04-01T23:59:59.000Z

442

Radioisotope Thermoelectric Generator Package O-Ring Seal Material Validation Testing  

SciTech Connect (OSTI)

The Radioisotope Thermoelectric Generator Package O-Ring Seal Material Validation Test was conducted to validate the use of the Butyl material as a primary seal throughout the required temperature range. Three tests were performed at (1) 233 K ({minus}40 {degrees}F), (2) a specified operating temperature, and (3) 244 K ({minus}20 {degrees}F) before returning to room temperature. Helium leak tests were performed at each test point to determine seal performance. The two major test objectives were to establish that butyl rubber material would maintain its integrity under various conditions and within specified parameters and to evaluate changes in material properties.

Adkins, H.E.; Ferrell, P.C.; Knight, R.C.

1994-09-30T23:59:59.000Z

443

Temperature sensor with improved thermal barrier and gas seal between the probe and housing  

DOE Patents [OSTI]

A temperature sensor comprising: a hollow tube with a first end and a second end, wherein the second end is closed sealing a cavity within the tube from an environment outside of the tube and wherein the first end has an exterior cylindrical surface; a temperature responsive sensing element within the tube proximate to the second end; a glass cylinder having an inner cylindrical surface in sealing engagement with the exterior cylindrical surface of the first end of the tube; and a sensor housing having an inner cylindrical cavity bounded by an inner cylindrical wall, wherein an outer cylindrical surface of the glass cylinder is sealingly engaged with the inner cylindrical wall.

O'Connell, David Peter (Canfield, OH); Sumner, Randall Christian (New Wilmington, PA)

1998-01-01T23:59:59.000Z

444

The effect of teeth-on-stator labyrinth seals on rotor imbalance response  

E-Print Network [OSTI]

difficuhies that necessitated major design changes. These changes included teplacement of the hydrostatic air bearings suppordng the jack shaft with grease lubricated bearings, modification of the seal housing to allow adequate air flow to the seal chamber... the effect on the mtor imbalance response. Tests were performed over a shaft speed range of 0 to 5000 tpm and an air pressure range of 0 to 225 psig at the seal inlet. The fourth objective of this research was to determine the cross-coupled stiffness...

Conway, Eileen Marie

2012-06-07T23:59:59.000Z

445

Simulation of bristle tip lift-off in a brush seal  

E-Print Network [OSTI]

material and rotor coating become major design considerations. Because of this, the bristles are made of a superalloy such as Hanes 25 and Hastelloy X and the rotor is coated with a highly polished ceramic such as Zirconium Dioxide or Chromium Carbide... P Low Bristles X Section A-A Backing ring A Figure 1. 2 Typical Brush Seal Arrangement function of the backing plate is to restrict the axial deflection of the of the bristles due to the pressure drop across the seal. Obviously, the seals...

Modi, Sandeep Subhash

1995-01-01T23:59:59.000Z

446

Initial field testing definition of subsurface sealing and backfilling tests in unsaturated tuff; Yucca Mountain Site Characterization Project  

SciTech Connect (OSTI)

This report contains an initial definition of the field tests proposed for the Yucca Mountain Project repository sealing program. The tests are intended to resolve various performance and emplacement concerns. Examples of concerns to be addressed include achieving selected hydrologic and structural requirements for seals, removing portions of the shaft liner, excavating keyways, emplacing cementitious and earthen seals, reducing the impact of fines on the hydraulic conductivity of fractures, efficient grouting of fracture zones, sealing of exploratory boreholes, and controlling the flow of water by using engineered designs. Ten discrete tests are proposed to address these and other concerns. These tests are divided into two groups: Seal component tests and performance confirmation tests. The seal component tests are thorough small-scale in situ tests, the intermediate-scale borehole seal tests, the fracture grouting tests, the surface backfill tests, and the grouted rock mass tests. The seal system tests are the seepage control tests, the backfill tests, the bulkhead test in the Calico Hills unit, the large-scale shaft seal and shaft fill tests, and the remote borehole sealing tests. The tests are proposed to be performed in six discrete areas, including welded and non-welded environments, primarily located outside the potential repository area. The final selection of sealing tests will depend on the nature of the geologic and hydrologic conditions encountered during the development of the Exploratory Studies Facility and detailed numerical analyses. Tests are likely to be performed both before and after License Application.

Fernandez, J.A. [Sandia National Labs., Albuquerque, NM (United States); Case, J.B.; Tyburski, J.R. [I. T. Corp., Albuquerque, NM (United States)

1993-05-01T23:59:59.000Z

447

Duct injection for SO{sub 2} control, Design Handbook, Volume 1, Process design and engineering guidelines  

SciTech Connect (OSTI)

PETC developed a comprehensive program of coal-related, acid-rain research and development with a major activity area centering on flue gas cleanup and control of SO{sub 2} emissions. Particular emphasis was placed on the retrofit measures for older coal-fired power plants which predate the 1971 New Source Performance Standards. Candidate emission control technologies fall into three categories, depending upon their point of application along the fuel path (i.e., pre, during, or post combustion). The post-combustion, in-duct injection of a calcium-based chemical reagent seemed promising. Preliminary studies showed that reagent injection between the existing air heater and electrostatic precipitator (ESP) could remove between 50-60% of the SO{sub 2} and produce an environmentally safe, dry, solid waste that is easily disposed. Although SO{sub 2} removal efficiencies were less, the estimated capital costs for duct injection technology were low making the economics of duct injection systems seem favorable when compared to conventional wet slurry scrubbers under certain circumstances. With the promulgation of the Clean Air Act Amendments of 1990 came more incentive for the development of low capital cost flue gas desulfurization (FGD) processes. A number of technical problems had to be resolved, however, before duct injection technology could be brought to a state of commercial readiness. The Duct Injection Technology Development Program was launched as a comprehensive, four-year research effort undertaken by PETC to develop this new technology. Completed in 1992, this Duct Injection Design Handbook and the three-dimensional predictive mathematical model constitute two primary end products from this development program. The aim of this design handbook and the accompanying math model is to provide utility personnel with sufficient information to evaluate duct injection technology against competing SO{sub 2} emissions reduction strategies for an existing plant.

NONE

1995-09-01T23:59:59.000Z

448

Energy Savings and Peak Demand Reduction of a SEER 21 Heat Pump vs. a SEER 13 Heat Pump with Attic and Indoor Duct Systems  

SciTech Connect (OSTI)

This report describes results of experiments that were conducted in an unoccupied 1600 square foot house--the Manufactured Housing (MH Lab) at the Florida Solar Energy Center (FSEC)--to evaluate the delivered performance as well as the relative performance of a SEER 21 variable capacity heat pump versus a SEER 13 heat pump. The performance was evaluated with two different duct systems: a standard attic duct system and an indoor duct system located in a dropped-ceiling space.

Cummings, J.; Withers, C.

2014-03-01T23:59:59.000Z

449

Effect of pre-oxidation and environmental aging on the seal strength of a novel high-temperature solid oxide fuel cell (SOFC) sealing glass with metallic interconnect  

SciTech Connect (OSTI)

A novel high-temperature alkaline-earth silicate sealing glass was developed for solid oxide fuel cell (SOFC) applications. The glass was used to join two ferritic stainless steel coupons for strength evaluation. The steel coupons were pre-oxidized at elevated temperatures to promote thick oxide layers to simulate long-term exposure conditions. In addition, seals to as-received metal coupons were also tested after aging in oxidizing or reducing environments to simulate the actual SOFC environment. Room temperature tensile testing showed strength degradation when using pre-oxidized coupons, and more extensive degradation after aging in air. Fracture surface and microstructural analysis confirmed that the cause of degradation was formation of SrCrO4 at the outer sealing edges exposed to air.

Chou, Y. S.; Stevenson, Jeffry W.; Singh, Prabhakar

2008-09-15T23:59:59.000Z

450

Microsoft Word - RedSeal_Smart Grid Policy Logistics RFI-sd.docx  

Broader source: Energy.gov (indexed) [DOE]

on Smart Grid RFI on Smart Grid RFI RedSeal Systems, Inc. 1 October 29, 2010 Office of Electricity Delivery and Energy Reliability US Department of Energy Room 8H033 1000 Independence Avenue, SW Washington, DC 20585 Re: Comments on "Smart Grid RFI: Addressing Policy and Logistical Challenges" 75 FR 57006 [FR Doc. 2010-23251] From: Steve Dauber Vice-President, Marketing RedSeal Systems 2121 South El Camino Real, Suite 300 San Mateo, CA 94403 Ph: 650-645-6209 sdauber@redseal.net www.redseal.net RedSeal Systems is a leading developer of security posture management software for large organizations and has provided their software to several major utilities for complex network security applications. RedSeal software - in use by more than 150 industry and

451

Calcium Film Based Testing of Edge-Seal Materials for Photovoltaic Applications (Presentation)  

SciTech Connect (OSTI)

Because of the sensitivity of some photovoltaic devices to moisture-induced corrosion, they are packaged using impermeable front- and back-sheets with an edge seal to prevent moisture ingress. Evaluation of edge seal materials can be difficult because of the low permeation rates involved and/or non-Fickian behavior. Here, using a Ca film deposited on a glass substrate, we demonstrate the evaluation of edge seal materials in a manner that effectively duplicates their use in a photovoltaic application and compare the results with standard methods for measuring water vapor transport. We demonstrate how moisture permeation data from polymer films can be used to estimate moisture ingress rates and compare the results of these two methods. Encapsulant materials were also evaluated for comparison and to highlight the need for edge seals. Of the materials studied, dessicant-filled polyisobutene materials demonstrate by far the best potential to keep moisture out for a 20 to 30 year lifetime.

Kempe, M.; Dameron, A.; Reese, M.

2011-04-01T23:59:59.000Z

452

Calcium Based Test Method for Evaluation of Photovoltaic Edge-Seal Materials (Presentation)  

SciTech Connect (OSTI)

Because of the sensitivity of some photovoltaic devices to moisture-induced corrosion, they are packaged using impermeable front- and back-sheets with an edge seal to prevent moisture ingress. Evaluation of edge seal materials can be difficult because of the low permeation rates involved and/or non-Fickian behavior. Here, using a Ca film deposited on a glass substrate, we demonstrate the evaluation of edge seal materials in a manner that effectively duplicates their use in a photovoltaic application and compare the results with standard methods for measuring water vapor transport. We demonstrate how moisture permeation data from polymer films can be used to estimate moisture ingress rates and compare the results of these two methods. Encapsulant materials were also evaluated for comparison and to highlight the need for edge seals. Of the materials studied, dessicant-filled polyisobutene materials demonstrate by far the best potential to keep moisture out for a 20 to 30 year lifetime.

Kempe, M.; Dameron, A.; Reese, M.

2011-02-01T23:59:59.000Z

453

Analytical and experimental evaluation of the leakage and stiffness characteristics of high pressure pocket damper seals  

E-Print Network [OSTI]

This thesis presents numerical predictions for the leakage and direct stiffness coefficients of pocket damper seals. Modifications made to earlier flow-prediction models are discussed. Leakage and static pressure measurements on straight...

Gamal Eldin, Ahmed Mohamed

2004-09-30T23:59:59.000Z

454

16 TAC, part 1, chapter 3, rule 3.7 Strata to be sealed off ...  

Open Energy Info (EERE)

3, rule 3.7 Strata to be sealed offLegal Abstract This explains the requirement that when wells are drilled for oil, gas, or geothermal resources in Texas the fluid must be...

455

James Walker develops Walkersele D8 a new rotary lip seal for marine propulsion systems  

Science Journals Connector (OSTI)

Walkersele D8 is a new design of rotary lip seal developed by James Walker & Co Ltd for use in marine propulsion systems to protect bearings from water ingress or prevent lubricant from leaking into the marine environment.

2012-01-01T23:59:59.000Z

456

Preparation, properties and chemistry of glass- and glass-ceramic-to-metal seals and coatings  

Science Journals Connector (OSTI)

An overview is given outlining the materials and technologies that have been employed in the preparation of glass- and glass-ceramic-to-metal seals and coatings. Metal/non-metal bonding theories are summarized...

I. W. Donald

1993-06-01T23:59:59.000Z

457

The effect of geometry changes on the performance of labyrinth seals  

E-Print Network [OSTI]

Leakage resistance measurements were conducted on stepped labyrinth seals using a 4-1 scale, two-dimensional, non-rotating test apparatus, with water as the working fluid. By sequentially varying the dimensions of a labyrinth sea], changes...

Brown, Lloyd Perryman

2012-06-07T23:59:59.000Z

458

An experimental and theoretical comparison of rotordynamic coefficients for sawtooth-pattern damper seals  

E-Print Network [OSTI]

u) ?. 5 DAMPER SEAL 0. 528mm cr. h/cr 2. 88 & y ~ D . 34 p SMOOTH SEAL ? 20 mils clr SAWTOOTH PATTERN Afl: y 0 . 4 SAWTOOTH PATTERN 1F2 s ~ 0 . 4 () SAWTOOTH PATTERN 193 a ~ 0 . 74 g SAWTOOTH PATTERN 84: ~ ~ 0 . 74 6 12 18 24 30 3 3 15 21... . 008 . 006 004 . 002 DAMPER SEAL 0. 526mm cr. h/cr Z. 69: y 0 . 34 p SMOOTH SEAL ? 20 mile clr SAWTOOTH PATTERN Af5: ~ 0 . 64 SAWTOOTH PATTERN 4'6 c ~ 0 . 49 0 SAWTOOTH PATTERN 1g7 c ~ 0 34 6 12 18 24 30 8 15 21 27 (Pa ? Pb) avg (Bars...

Nolan, Steven Anthony

2012-06-07T23:59:59.000Z

459

Energy intake and utilisation by nursing bearded seal (Erignathus barbatus) pups from Svalbard, Norway  

Science Journals Connector (OSTI)

In this study we measure energy intake via milk in nursing bearded seal (Erignathus barbatus) pups and determine how this energy is allocated into metabolism and storage of new tissues. This was accomplished usin...

C. Lydersen; K. M. Kovacs; M. O. Hammill; I. Gjertz

1996-11-01T23:59:59.000Z

460

Development of multiscale models for the performance of the gas and oil seals in rotary engines  

E-Print Network [OSTI]

Rotary engines offer higher power density, fewer parts and lower vibrations than conventional reciprocating piston engines. However, rotary engines are more difficult to seal because of the rotor shape which leads to higher ...

Picard, Mathieu

2014-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "aerosol-based duct sealing" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


461

ABUNDANCE, MOVEMENTS, AND FEEDING HABITS OF HARBOR SEALS, PHOCA VITULINA, AT  

E-Print Network [OSTI]

on tidally exposed sand flats in both bays. Harbor seal abundance at Tillamook Bay peaked during pupping (May found in estuaries, along isolated shorelines, and on nearshore rocky islets. Before protection

462

Experimental measurement and analysis of wall pressure distribution for a 50% eccentric whirling annular seal  

E-Print Network [OSTI]

, whirl ratios ranging between ? 0.5 were tested. From the collected data a detailed analysis of wall pressures along the seal surface is performed following the technique described by Winslow (1994) and Robic (1999)....

Suryanarayanan, Arun

2004-11-15T23:59:59.000Z

463

Large-scale experimental investigation of flow characteristics in labyrinth seal geometries  

E-Print Network [OSTI]

order to determine the flow characteristics and leakage resistance properties of advanced labyrinth seals. A unique water test facility is used to acquire leakage resistance measurements for two-dimensional, planar models of multi-cavity, stepped...

Younger, James Stanton

1994-01-01T23:59:59.000Z

464

Experimental evaluation of force coefficients of metal mesh hybrid pocket damper seal  

E-Print Network [OSTI]

in its development, the tested metal mesh hybrid pocket damper seal induced a gripping force on the shaft that increased with upstream pressure. The resulting friction torque was beyond acceptable limits. The target after that was to develop...

Ahmad, Nauman

2001-01-01T23:59:59.000Z

465

Visible Watermarking using Verifiable Digital Seal Image Hyuncheol Park* Kwangjo Kim*  

E-Print Network [OSTI]

authentication since it provides a mechanism that hides some information in cover data ­ images, video, audio. But, we can guarantee the authenticity of cover data, because the damaged authentic information seal SCIS 2001 The 2001 Symposium on Crypto

Kim, Kwangjo

466

The Subsistence Harvest of Northern Fur Seals St. George Island in 2006  

E-Print Network [OSTI]

.................................................................................................................... 6 By Products and Waste..................................... 6 Heat Strokes on: a) the number of sub-adult male fur seals harvested, b) incidence of by-products and waste during

467

Texas GLO Oil and Gas Sealed Bid Forms | Open Energy Information  

Open Energy Info (EERE)

search OpenEI Reference LibraryAdd to library Legal Document- OtherOther: Texas GLO Oil and Gas Sealed Bid FormsLegal Abstract The Texas General Land Office provides various...

468

MC4523 Sealed Cap: Component & characteristics development report  

SciTech Connect (OSTI)

The MC4523 Sealed Cap is a WW42C1 Percussion Primer that is pressed into a steel cylinder. Hermaticity of the input end is then provided by welding a thin steel closure disk on the input end of the MC4523. Thus, the user is provided with a component that is prequalified in terms of ignition sensitivity and hermeticity. The first customer is the Thermal Battery Department (1522). The MC4523 will be used on the MC2736A Thermal Battery which in turn will be used on the W78 JTA. Attachment of the MC4523 to the battery is with a laser weld. Combined test results of four production lots at a commercial supplier (PPI, TMS, WR1, and WR2) show an all-fire ignition sensitivity (.999 @ 50%) of approximately 60 millijoules of mechanical energy with a 2.2 gram firing pin. The firing pin had an impact tip with a radius of 0.020 inch. This firing pin is like that to be used in the W78 JTA application. Approximately 112 millijoules of mechanical energy will be supplied in the application, thus the design margin is more than adequate.

Begeal, D.R.

1997-03-01T23:59:59.000Z

469

Instrument for measurement of vacuum in sealed thin wall packets  

DOE Patents [OSTI]

An instrument is described for the measurement of vacuum within sealed packets, the packets having a wall sufficiently thin that it can be deformed by the application of an external vacuum to small area thereof. The instrument has a detector head for placement against the deformable wall of the packet to apply the vacuum in a controlled manner to accomplish a limited deformation or lift of the wall, with this deformation or lift monitored by the application of light as via a bifurcated light pipe. Retro-reflected light through the light pipe is monitored with a photo detector. An abrupt change (e.g., a decrease) of retro-reflected light signals the wall movement such that the value of the vacuum applied through the head to achieve this initiation of movement is equal to the vacuum within the packet. In a preferred embodiment a vacuum reference plate is placed beneath the packet to ensure that no deformation occurs on the reverse surface of the packet. A packet production line model is also described. 3 figures.

Kollie, T.G.; Thacker, L.H.; Fine, H.A.

1993-10-05T23:59:59.000Z

470

DECOMMISSIONING OF A CAESIUM-137 SEALED SOURCE PRODUCTION FACILITY  

SciTech Connect (OSTI)

Amersham owns a former Caesium-137 sealed source production facility. They commissioned RWE NUKEM to carry out an Option Study to determine a strategy for the management of this facility and then the subsequent decommissioning of it. The decommissioning was carried out in two sequential phases. Firstly robotic decommissioning followed by a phase of manual decommissioning. This paper describes the remote equipment designed built and operated, the robotic and manual decommissioning operations performed, the Safety Management arrangements and summarizes the lessons learned. Using the equipment described the facility was dismantled and decontaminated robotically. Some 2300kg of Intermediate Level Waste containing in the order of 4000Ci were removed robotically from the facility. Ambient dose rates were reduced from 100's of R per hour {gamma} to 100's of mR per hour {gamma}. The Telerobotic System was then removed to allow man access to complete the decommissioning. Manual decommissioning reduced ambient dose rates further to less than 1mR per hour {gamma} and loose contamination levels to less than 0.25Bq/cm2. This allowed access to the facility without respiratory protection.

Murray, A.; Abbott, H.

2003-02-27T23:59:59.000Z

471

Instrument for measurement of vacuum in sealed thin wall packets  

DOE Patents [OSTI]

An instrument for the measurement of vacuum within sealed packets 12, the packets 12 having a wall 14 that it can be deformed by the application of an external dynamic vacuum to an area thereof. The instrument has a detector head 18 for placement against the deformable wall 14 of the packet to apply the vacuum in a controlled manner to accomplish a limited deformation or lift of the wall 14, with this deformation or lift monitored by the application of light as via a bifurcated light pipe 20. Retro-reflected light through the light pipe is monitored with a photo detector 26. A change (e.g., a decrease) of retro-reflected light signals the wall movement such that the value of the dynamic vacuum applied through the head be to achieve this initiation of movement is equal to the vacuum within the packet 12. In a preferred embodiment a vacuum plate 44 is placed beneath the packet 12 to ensure that no deformation occurs on the reverse surface 16 of the packet. A vacuum can be applied to a recess in this vacuum plate, the value of which can be used to calibrate the vacuum transducer in the detector head.

Kollie, Thomas G. (Oak Ridge, TN); Thacker, Louis H. (Knoxville, TN); Fine, H. Alan (Lexington, KY)

1995-01-01T23:59:59.000Z

472

Instrument for measurement of vacuum in sealed thin wall packets  

DOE Patents [OSTI]

An instrument is disclosed for the measurement of vacuum within sealed packets, the packets having a wall that it can be deformed by the application of an external dynamic vacuum to an area thereof. The instrument has a detector head for placement against the deformable wall of the packet to apply the vacuum in a controlled manner to accomplish a limited deformation or lift of the wall with this deformation or lift monitored by the application of light as via a bifurcated light pipe. Retro-reflected light through the light pipe is monitored with a photo detector. A change (e.g., a decrease) of retro-reflected light signals the wall movement such that the value of the dynamic vacuum applied through the head be to achieve this initiation of movement is equal to the vacuum within the packet. In a preferred embodiment a vacuum plate is placed beneath the packet to ensure that no deformation occurs on the reverse surface of the packet. A vacuum can be applied to a recess in this vacuum plate, the value of which can be used to calibrate the vacuum transducer in the detector head. 4 figs.

Kollie, T.G.; Thacker, L.H.; Fine, H.A.

1995-04-18T23:59:59.000Z

473

Instrument for measurement of vacuum in sealed thin wall packets  

DOE Patents [OSTI]

An instrument for the measurement of vacuum within sealed packets 12, the packets 12 having a wall 14 sufficiently thin that it can be deformed by the application of an external vacuum to small area thereof. The instrument has a detector head 18 for placement against the deformable wall 14 of the packet to apply the vacuum in a controlled manner to accomplish a limited deformation or lift of the wall 14, with this deformation or lift monitored by the application of light as via a bifurcated light pipe 20. Retro-reflected light through the light pipe is monitored with a photo detector 26. An abrupt change (e.g., a decrease) of retro-reflected light signals the wall movement such that the value of the vacuum applied through the head 18 to achieve this initiation of movement is equal to the vacuum Within the packet 12. In a preferred embodiment a vacuum reference plate 44 is placed beneath the packet 12 to ensure that no deformation occurs on the reverse surface 16 of the packet. A packet production line model is also described.

Kollie, Thomas G. (117 Oklahoma Ave., Oak Ridge, TN 37830); Thacker, Louis H. (3727 Frostwood Rd., Knoxville, TN 37921); Fine, H. Alan (949 Wishbone Cir., Lexington, KY 40502)

1993-01-01T23:59:59.000Z

474

PRESSURE DEVELOPMENT IN SEALED CONTAINERS WITH PLUTONIUM BEARING MATERIALS  

SciTech Connect (OSTI)

Gas generation by plutonium-bearing materials in sealed containers has been studied. The gas composition and pressure are determined over periods from months to years. The Pu-bearing materials studied represent those produced by all of the major processes used by DOE in the processing of plutonium and include the maximum amount of water (0.5% by weight) allowed by DOE's 3013 Standard. Hydrogen generation is of high interest and the Pu-bearing materials can be classed according to how much hydrogen is generated. Hydrogen generation by high-purity plutonium oxides packaged under conditions typical for actual 3013 materials is minimal, with very low generation rates and low equilibrium pressures. Materials with chloride salt impurities have much higher hydrogen gas generation rates and result in the highest observed equilibrium hydrogen pressures. Other materials such as those with high metal oxide impurities generate hydrogen at rates in between these extremes. The fraction of water that is converted to hydrogen gas as equilibrium is approached ranges from 0% to 25% under conditions typical of materials packaged to the 3013 Standard. Generation of both hydrogen and oxygen occurs when liquid water is present. The material and moisture conditions that result in hydrogen and oxygen generation for high-purity plutonium oxide and chloride salt-bearing plutonium oxide materials have been characterized. Other gases that are observed include nitrous oxide, carbon dioxide, carbon monoxide, and methane.

Duffey, J.; Livingston, R.

2010-02-01T23:59:59.000Z

475

Innovative Self-Healing Seals for Solid Oxide Fuel Cells (SOFCs) University of Cincinnati  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Innovative Self-Healing Seals for Solid Innovative Self-Healing Seals for Solid Oxide Fuel Cells (SOFCs)-University of Cincinnati Background The mission of the U.S. Department of Energy (DOE) National Energy Technology Laboratory (NETL) is to advance energy options to fuel our economy, strengthen our security, and improve our environment. With the Solid State Energy Conversion Alliance (SECA), NETL is leading the research, development, and demonstration of solid oxide

476

Comparison of the Leakage Characteristics of the Straight Annular and Convergent Seals  

E-Print Network [OSTI]

=0.1 mm, 0-20,200 rpm, water flow) .............................................................................. 88 Fig. 54 Leakage rates for the convergent seal configurations (Cex=0.1 mm, 0- 20,200 rpm, water Flow... configurations (Cex=0.1 mm, 20,200 rpm, air flow, Pr=0.17) ........................ 92 Fig. 57 Pressure distributions for the straight annular and convergent seal configurations (Cex=0.2 mm, 0-20,200 rpm, air flow, Pr=0.28) .................... 94 Fig. 58...

Ustun, Serafettin

2012-10-19T23:59:59.000Z

477

Identification of force coefficients in a squeeze film damper with a mechanical seal  

E-Print Network [OSTI]

IDENTIFICATION OF FORCE COEFFICIENTS IN A SQUEEZE FILM DAMPER WITH A MECHANICAL SEAL A Thesis by ADOLFO DELGADO-MARQUEZ Submitted to the Office of Graduate Studies of Texas A&M University in partial fulfillment... of the requirements for the degree of MASTER OF SCIENCE December 2005 Major Subject: Mechanical Engineering IDENTIFICATION OF FORCE COEFFICIENTS IN A SQUEEZE FILM DAMPER WITH A MECHANICAL SEAL A Thesis by ADOLFO DELGADO...

Delgado-Marquez, Adolfo

2006-04-12T23:59:59.000Z

478

Experimental and theoretical rotordynamic coefficients and leakage of straight smooth annular gas seals  

E-Print Network [OSTI]

-dimensional flow coefficient ? Rotor speed [1/T] ? Excitation frequency [1/T] Subscripts ij Direction of response and force 1 INTRODUCTION Annular gas seals are used in a variety of turbomachinery applications. Different seal configurations...] turbulent bulk flow model are developed, and then a perturbation analysis is employed to obtain a set of zero- and first- order equations. Integration of the zeroth-order equations yields the leakage and integration of the first-order equations yields...

Kerr, Bradley Gray

2005-02-17T23:59:59.000Z

479

Constitutive model effects on finite element modeling of elastomer behavior in radial interference seal configurations  

E-Print Network [OSTI]

CONSTITUTIVE MODEL EFFECTS ON FINITE ELEMENT MODELING OF ELASTOMER BEHAVIOR IN RADIAL INTERFERENCE SEAL CONFIGURATIONS A Thesis by JASON R. JACKSON Subnutted to the Office of Graduate Studies of Texas A&M University in partial fulfillment... of the requirements for the degree of MASTER OF SCIENCE August 1996 Major Subject: Mechanical Engineering CONSTITUTIVE MODEL EFFECTS ON FINITE ELEMENT MODELING OF ELASTOMER BEHAVIOR IN RADIAL INTERFERENCE SEAL CONFIGURATIONS A Thesis by JASON R. JACKSON...

Jackson, Jason R.

1996-01-01T23:59:59.000Z

480

Innovative Self-Healing Seals for Solid Oxide Fuel Cells (SOFC)  

SciTech Connect (OSTI)

Solid oxide fuel cell (SOFC) technology is critical to several national initiatives. Solid State Energy Conversion Alliance (SECA) addresses the technology needs through its comprehensive programs on SOFC. A reliable and cost-effective seal that works at high temperatures is essential to the long-term performance of the SOFC for 40,000 hours at 800°C. Consequently, seals remain an area of highest priority for the SECA program and its industry teams. An innovative concept based on self-healing glasses was advanced and successfully demonstrated through seal tests for 3000 hours and 300 thermal cycles to minimize internal stresses under both steady state and thermal transients for making reliable seals for the SECA program. The self-healing concept requires glasses with low viscosity at the SOFC operating temperature of 800°C but this requirement may lead to excessive flow of the glass in areas forming the seal. To address this challenge, a modification to glass properties by addition of particulate fillers is pursued in the project. The underlying idea is that a non-reactive ceramic particulate filler is expected to form glass-ceramic composite and increase the seal viscosity thereby increasing the creep resistance of the glass-composite seals under load. The objectives of the program are to select appropriate filler materials for making glass-composite, fabricate glass-composites, measure thermal expansion behaviors, and determine stability of the glass-composites in air and fuel environments of a SOFC. Self-healing glass-YSZ composites are further developed and tested over a longer time periods under conditions typical of the SOFCs to validate the long-term stability up to 2000 hours. The new concepts of glass-composite seals, developed and nurtured in this program, are expected to be cost-effective as these are based on conventional processing approaches and use of the inexpensive materials.

Raj Singh

2012-06-30T23:59:59.000Z

Note: This page contains sample records for the topic "aerosol-based duct sealing" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


481

Schematic designs for penetration seals for a reference repository in bedded salt  

SciTech Connect (OSTI)

The isolation of radioactive wastes in geologic repositories requires that man-made penetrations such as shafts, tunnels, or boreholes are adequately sealed. This report describes schematic seal designs for a repository in bedded salt referenced to the straitigraphy of southeastern New Mexico. The designs are presented for extensive peer review and will be updated as site-specific conceptual designs when a site for a repository in salt has been selected. The principal material used in the seal system is crushed salt obtained from excavating the repository. It is anticipated that crushed salt will consolidate as the repository rooms creep close to the degree that mechanical and hydrologic properties will eventually match those of undisturbed, intact salt. For southeastern New Mexico salt, analyses indicate that this process will require approximately 1000 years for a seal located at the base of one of the repository shafts (where there is little increase in temperature due to waste emplacement) and approximately 400 years for a seal located in an access tunnel within the repository. Bulkheads composed of contrete or salt bricks are also included in the seal system as components which will have low permeability during the period required for salt consolidation.

Kelsall, P.C.; Case, J.B.; Meyer, D.; Coons, W.E.

1982-11-01T23:59:59.000Z

482

Tags and seals for controling nuclear materials, Arms control and nonproliferation technologies. Second quarter 1993  

SciTech Connect (OSTI)

This issue of Arms Control and Nonproliferation Technologies summarizes demonstrations and addresses related topics. The first article, ``Basic Nuclear Material Control and Accountability Concepts as Might be Applied to the Uranium from the US-Russian HEU Purchase,`` describes safeguards sybsystems necessary for effective nuclear material safeguards. It also presents a general discussion on HEU-to-low-enrichment uranium (LEU) commingling processes and suggests applicable key measurement points. The second article, ``A Framework for Evaluating Tamper-Indicating-Device Technologies (TIDs),`` describes their uses, proper selection, and evaluation. The final three articles discuss the tags and seals applications and general characteristics of several nuclear material containers: the Type 30B uranium hexafluoride container, the AT-400R container, and the DOT Specification 6M container for SNM. Finally, the Appendix displays short descriptions and illustrations of seven tags and seals, including: the E-cup and wire seal, the python seal, the secure loop inspectable tag/seal (SLITS), bolt-and-loop type electronic identification devices, and the shrink-wrap seal.

Staehle, G; Talaber, C; Stull, S; Moulthrop, P [eds.

1993-12-31T23:59:59.000Z

483

Finite element analysis of laminar mixed convection in the entrance region of horizontal annular ducts  

SciTech Connect (OSTI)

The laminar mixed convection in the entrance region of horizontal straight ducts of an annular cross section is studied by means of a generally applicable finite element procedure based on the parabolized simplification of the Navier-Stokes and energy equations and on the Boussinesq approximation of the buoyancy term. The procedure is validated through comparisons of computed results with available data from the literature. New results concern annuli with radius ratios equal to 0.25, 0.5, and 0.75 subjected to the fundamental boundary condition of the second and the third kinds, for Prandtl numbers equal to 0.7 and 7, and different values of Grashof number.

Nonino, C.; Giudice, S. del [Univ. di Udine (Italy). Dipt. di Energetica e Macchine

1996-02-23T23:59:59.000Z

484

Building America Case Study: Raised Ceiling Interior Duct System, New Smyrna, Florida (Fact Sheet)  

SciTech Connect (OSTI)

One of BA-PIRC's longtime Habitat for Humanity partners, S.E. Volusia CO (SEVHFH), was interested in building a home to the new Challenge Home standards. SEVHFH routinely builds ENERGY STAR V3.1 homes. The only modification to their design needed to comply with the Challenge Home criteria was the interior duct requirement. Unwilling to incur the added costs of a foam roof deck or wall heights above 8 feet to accommodate a fur-down chase SEVHFH opted to build a fur-up or raised ceiling chase.

Not Available

2014-09-01T23:59:59.000Z

485

An analysis of fluid flow by electrical analogy as applied to air ducts  

E-Print Network [OSTI]

. 0 10. 0 14. 9 9-4 12. 0 VELOCITY FPM 1600 1460 1570 1300 TOTAL PRESSURE DROP IN. WATER 0 04 0. 10 0 02 o o8 o. o8 TABLE 3 21 PART III ALMQJATING CUHREYZ N. . GAME CALCULATOR APPLIED TO THE TOTAL PiiBSURE DROP METHOD GIVEN... resistance for Section B is then read to be 13. 3$ ohms which gives an R oi' 38 ' 2 ohms. From Figure 4 the velocity is found to be 1400 fpm and duct diameter 14. 9 inches. fhe voltage drop for Section D is read to be 10. 0 volts, giving a total head loss...

Howard, Charles Pinto

2012-06-07T23:59:59.000Z

486

An advanced economizer controller for dual-duct air-handling systems -- with a case application  

SciTech Connect (OSTI)

A heating penalty is expected when economizers are applied to dual-duct air-handling systems. The heating penalty can be even higher than the cooling savings when the hot airflow is higher than the cold airflow. To avoid the excessive heating penalty, advanced economizers are developed in this paper. The application of the advanced economizer has resulted in savings of $7,000/yr in one 95,000-ft{sup 2} (8,800-m{sup 2}) school building since 1993. The impacts of cold and hot deck settings on the energy consumption are also discussed.

Liu, M.; Claridge, D.E. [Texas A and M Univ., College Station, TX (United States). Mechanical Engineering Dept.; Park, B.Y. [Engineering Education Inst., Inchon (Korea, Republic of). Dept. of Architectural Engineering

1997-12-31T23:59:59.000Z

487

Effect of aluminizing of Cr-containing ferritic alloys on the seal strength of a novel high-temperature solid oxide fuel cell sealing glass  

SciTech Connect (OSTI)

A novel high-temperature alkaline-earth silicate sealing glass was developed for solid oxide fuel cell (SOFC) applications. The glass was used to join two metallic coupons of Cr-containing ferritic stainless steel for seal strength evaluation. In previous work, SrCrO4 was found to form along the glass/steel interface, which led to severe strength degradation. In the present study, aluminization of the steel surface was investigated as a remedy to minimize or prevent the strontium chromate formation. Three different processes for aluminization were evaluated with Crofer22APU stainless steel: pack cementation, vapor phase deposition, and aerosol spraying. It was found that pack cementation resulted in a rough surface with occasional cracks in the Al-diffused region. Vapor phase deposition yielded a smoother surface, but the resulting high Al content increased the coefficient of thermal expansion (CTE), resulting in failure of joined coupons. Aerosol spraying of an Al-containing salt resulted in formation of a thin aluminum oxide layer without any surface damage. The room temperature seal strength was evaluated in the as-fired state and in environmentally aged conditions. In contrast to earlier results with uncoated Crofer22APU, the aluminized samples showed no strength degradation even for samples aged in air. Interfacial and chemical compatibility was also investigated. The results showed aluminization to be a viable candidate approach to minimize undesirable chromate formation between alkaline earth silicate sealing glass and Cr-containing interconnect alloys for SOFC applications.

Chou, Y. S.; Stevenson, Jeffry W.; Singh, Prabhakar

2008-12-01T23:59:59.000Z

488

Nuclear reactor fuel assembly duct-tube-to-handling-socket attachment system  

DOE Patents [OSTI]

A reusable system for removably attaching the upper end 10of a nuclear reactor duct tube to the lower end 30 of a nuclear reactor fuel assembly handling socket. A transition ring 20, fixed to the duct tube's upper end 10, has an interior-threaded section 22 with a first locking hole segment 24. An adaptor ring 40, fixed to the handling socket's lower end 30 has an outside-threaded section 42 with a second locking hole segment 44. The inside 22 and outside 42 threaded sections match and can be joined so that the first 24 and second 44 locking hole segments can be aligned to form a locking hole. A locking ring 50, with a locking pin 52, slides over the adaptor ring 40 so that the locking pin 52 fits in the locking hole. A swage lock 60 or a cantilever finger lock 70 is formed from the locking cup collar 26 to fit in a matching groove 54 or 56 in the locking ring 50 to prevent the locking ring's locking pin 52 from backing out of the locking hole.

Christiansen, David W. (Kennewick, WA); Smith, Bob G. (Kennewick, WA)

1982-01-01T23:59:59.000Z

489

Small Arteriovenous Malformation of the Common Bile Duct Causing Hemobilia in a Patient with Hereditary Hemorrhagic Telangiectasia  

SciTech Connect (OSTI)

We report a 54-year-old male patient with arteriovenous malformation located at the common bile duct and hereditary hemorrhagic telangiectasia. The patient was treated as gallstone pancreatitis at first. Three days after endoscopic nasobiliary drainage (ENBD) for biliary drainage to subside gallstone pancreatitis, hemobilia was drained from the ENBD tube and the serum hemoglobin level gradually decreased. Cholangioscopy and angiography revealed that hemobilia was due to a small arteriovenous malformation located at the common bile duct. Subsequently, the patient was successfully treated by endovascular intervention.

Hayashi, Sadao, E-mail: hayashi@m.kufm.kagoshima-u.ac.jp; Baba, Yasutaka; Ueno, Kazuto; Nakajo, Masayuki [Kagoshima University Graduate School of Medical and Dental Sciences, Department of Radiology (Japan)

2008-07-15T23:59:59.000Z

490

Cross spectra between temperature and pressure in a constant area duct downstream of a hydrogen fueled combustor  

Science Journals Connector (OSTI)

It was shown in a recent paper [J. H. Miles and E. A. Krejsa J. Acoust. Soc. Am. 72 20082019 (1982)] that knowledge of pressure?temperature auto spectra and cross spectra could be used in a model for sound propagation in a variable duct having acoustic and convected entropy fluctuations. The present exploratory study investigates the measurement of pressure?temperature cross spectra and coherence and temperature cross spectra and coherence at well separated points in a combustion rig. Data obtained near the inlet and the exit of a 6.44?m?long duct attached to a J?47 combustor fueled with hydrogen are presented.

J. H. Miles; C. A. Wasserbauer; E. A. Krejsa

1983-01-01T23:59:59.000Z

491

High-Speed Internet Access via HVAC Ducts: A New Approach Daniel D. Stancil, Ozan K. Tonguz, Ariton Xhafa, Ahmet Cepni, and Pavel Nikitin  

E-Print Network [OSTI]

High-Speed Internet Access via HVAC Ducts: A New Approach Daniel D. Stancil, Ozan K. Tonguz, Ariton conditioning (HVAC) ducts for indoor wireless transmission systems and networks. Mea- surements and system to 100 Mbps should be possible, when HVAC system is used in con- junction with OFDM technology. Keywords

Stancil, Daniel D.

492

Measure Guideline: Wall Air Sealing and Insulation Methods in Existing Homes; An Overview of Opportunity and Process  

SciTech Connect (OSTI)

This guide provides renovators and retrofit contractors an overview of considerations when including wall air sealing and insulation in an energy retrofit project. It also outlines the potential project risks, various materials for insulating, possible field inspections needed, installation procedures, as well as the benefits and drawbacks. The purpose of this document is to provide the outline of the overview and process of insulating and air sealing walls so that home retrofit professionals can identify approaches to air sealing and insulation measures.

Roberts, S.; Stephenson, R.

2012-09-01T23:59:59.000Z

493

Procedure and Application for Determining the Cold Deck and Hot Deck Airflow in a Dual-Duct System  

E-Print Network [OSTI]

This paper introduces an innovative method to determine the cold and hot airflow through a dual-duct variable air volume (VAV) system. The actual building load can be identified based on the calculated airflow and temperature for both the cold...

Liu, G.; Mingsheng, L.

2006-01-01T23:59:59.000Z

494

Orthogonality relations for fluid-structural waves in a three-dimensional, rectangular duct with flexible walls  

Science Journals Connector (OSTI)

...ventilation and air conditioning (HVAC), provide ideal channels for...such systems do not satisfy standard orthogonality conditions, such...however, exist albeit of non-standard form, and Lawrie Abrahams...particular relevance to the HVAC industry because many HVAC ducts...

2009-01-01T23:59:59.000Z

495

Exploring Maximum Humidity Control and Energy Conservation Opportunities with Single Duct Single Zone Air-Handling Units  

E-Print Network [OSTI]

Humidity control for single-duct single-zone (SDSZ) constant volume air handling units is known to be a challenge. The operation of these systems is governed by space temperature only. Under mild weather conditions, discharge air temperature can get...

Zhou, J.; Wei, G.; Turner, W. D.; Deng, S.; Claridge, D.

2006-01-01T23:59:59.000Z

496

Evaluation of mixing downstream of tees in duct systems with respect to single point representative air sampling  

E-Print Network [OSTI]

improvement in 3 hydraulic diameters needed to achieve COVs below 10%. Without an air blender, the distance downstream of the T-junction for the COVs below 20% increased as the velocity of the sub duct airflow increased. About 95% of the cases achieved COVs...

Kim, Taehong

2012-06-07T23:59:59.000Z

497

Influence of Tip Clearance and Inlet Flow Distortion on Ducted Fan Performance in VTOL UAVs Graduate Research Assistant  

E-Print Network [OSTI]

(Pa) CpTotal = Total pressure coefficient = Rotational speed (radian/sec) r = Radial distance measured military tasks, they can continuously transmit surveillance data and act as a relay station. Although to study the flow characteristics of ducted fans. Abrego and Bulaga [1] performed wind tunnel tests

Camci, Cengiz

498

This Opinion was filed under seal on February 26, 2010. The court requested tha  

Broader source: Energy.gov (indexed) [DOE]

This Opinion was filed under seal on February 26, 2010. The court requested that if This Opinion was filed under seal on February 26, 2010. The court requested that if 1 either party believed that the February 26, 2010 Opinion contained protected material that should be redacted before publication, that party shall, by motion filed on or before March 1, 2010, request that such protected material be redacted. The court has received no motions from either party requesting that the February 26, 2010 Opinion be redacted. The court therefore publishes the February 26, 2010 Opinion in its entirety. In the United States Court of Federal Claims No. 09-864 C (E-Filed: February 26, 2010, Under Seal) (Refiled: March 2, 2010) 1 ) Bid Protest; Statutory Interpretation; Small Business Administration; Priority of Historically Underutilized Business Zone Program over 8(a)

499

SRS Seals Access to P and R Reactors, Marking End to Nearly 60-Years of  

Broader source: Energy.gov (indexed) [DOE]

Seals Access to P and R Reactors, Marking End to Nearly Seals Access to P and R Reactors, Marking End to Nearly 60-Years of History: American Recovery and Reinvestment Act Project Progress SRS Seals Access to P and R Reactors, Marking End to Nearly 60-Years of History: American Recovery and Reinvestment Act Project Progress June 28, 2011 - 12:00pm Addthis Marc Sharpe, who was a senior reactor operator at P Reactor in the mid-1980s, (left) and Dr. David Moody, U.S. Department of Energy-Savannah River Operation Office Manager, were the last people to leave P Reactor, just before the opening is welded shut. Marc Sharpe, who was a senior reactor operator at P Reactor in the mid-1980s, (left) and Dr. David Moody, U.S. Department of Energy-Savannah River Operation Office Manager, were the last people to leave P Reactor,

500

"Aegean Seals of the Late Bronze Age: Masters and Workshops, II. The First Generation Minoan Masters"  

E-Print Network [OSTI]

the popular Groups.2 The serpentine seals found armost excrusively in LM r 6..irr, .o.r,.** comprise the more naturalistic Cretan popular Gro.rf O....fr*, ,fr. Cp Group); the steatite seals.found m.osrry o.r th. M#il";,;.-.iio,r"tty in the Islands, and rarely...*p"r. the lions on IX 114 and,7D,.lor. ,o the J-L Masrer. Lions, Bulls, Stags, Boars: The Master. ].31j 11:al_{:_.1 Jap!9io and 272 (5, 6) from Rutsi (both LH ilA). Aegean seals: masters and workshops l2l animals (note the waterbirds' legs on I273). The careful...

Younger, John G.

1982-01-01T23:59:59.000Z