Powered by Deep Web Technologies
Note: This page contains sample records for the topic "advanced sequential dual" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


1

Advanced Materials for RSOFC Dual Operation with Low Degradation  

SciTech Connect

Reversible solid oxide fuel cells (RSOFCs) are energy conversion devices. They are capable of operating in both power generation mode (SOFC) and electrolysis modes (SOEC). RSOFC can integrate renewable production of electricity and hydrogen when power generation and steam electrolysis are coupled in a system, which can turn intermittent solar and wind energy into "firm power." In this DOE EERE project, VPS continuously advanced RSOFC cell stack technology in the areas of endurance and performance. Over 20 types of RSOFC cells were developed in the project. Many of those exceeded performance (area specific resistance less than 300 mohmcm2) and endurance (degradation rate less than 4% per 1000 hours) targets in both fuel cell and electrolysis modes at 750C. One of those cells, RSOFC-7, further demonstrated the following: Steady-state electrolysis with a degradation rate of 1.5% per 1000 hours. Ultra high current electrolysis over 3 A/cm2 at 75% water electrolysis efficiency voltage of 1.67 V. Daily SOFC/SOEC cyclic test of over 600 days with a degradation rate of 1.5% per 1000 hours. Over 6000 SOFC/SOEC cycles in an accelerated 20-minute cycling with degradation less than 3% per 1000 cycles. In RSOFC stack development, a number of kW-class RSOFC stacks were developed and demonstrated the following: Steady-state electrolysis operation of over 5000 hours. Daily SOFC/SOEC cyclic test of 100 cycles. Scale up capability of using large area cells with 550 cm2 active area showing the potential for large-scale RSOFC stack development in the future. Although this project is an open-ended development project, this effort, leveraging Versa Power Systems' years of development experience, has the potential to bring renewable energy RSOFC storage systems significantly closer to commercial viability through improvements in RSOFC durability, performance, and cost. When unitized and deployed in renewable solar and wind installations, an RSOFC system can enable higher availability for intermittent renewable resources, thereby improving the commercial viability of these types of energy resources.

Eric, Tang; Tony, Wood; Sofiane, Benhaddad; Casey, Brown; Hongpeng, He; Jeff, Nelson; Oliver, Grande; Ben, Nuttall; Mark, Richards; Randy, Petri

2012-12-27T23:59:59.000Z

2

Method for starting and operating an advanced regenerative parallel compound dual fluid heat engine-advanced Cheng cycle(ACC)  

SciTech Connect

In a Cheng cycle, dual fluid heat engine of the type is described having: (i) a gas turbine engine including a compressor for compressing a first working fluid, having a compressor outlet, a combustion chamber in fluid communication with the compressor outlet, a turbine unit having an inlet in fluid communication with the combustion chamber for performing work by expansion of working fluid, and a turbine exhaust; (ii) a heat recovery steam generator coupled to the turbine exhaust for heating a second working fluid having a superheater with an outlet and an inlet, an evaporator having an outlet coupled to the superheater inlet and an evaporator inlet, a heat recovery boiler between the evaporator inlet and outlet having a drum; (iii) an injector for introducing heated second working fluid from the heat recovery steam generator into the gas turbine; (iv) a coolant inlet port for introducing coolant to at least one of turbine nozzles and blades in the gas turbine; and (v) control valve means for selectively throttling flow rate of second working fluid into the gas turbine connected upstream of the injector; (vi) a compressed gas source and pressure regulator selectively in communication with the drum; (vii) a sensor system coupled to gas turbine engine and the heat recovery steam generator for temperature and pressure detection; and (viii) a control system for operating fuel flow to the gas turbine; a method of operation of the heat engine comprising: (a) initializing start conditions in the gas turbine engine and the heat recovery steam generator with the control system; (b) setting the control valve means for idle flow condition of the heat engine; (c) pressurizing the drum with the compressed gas source, (d) starting the gas turbine engine from idle to full load; (e) throttling second working fluid flow rate with the control valve means and shutting off the compressed gas source.

Cheng, D.Y.

1993-08-10T23:59:59.000Z

3

A 65nm dual-mode baseband and multimedia application processor SoC with advanced power and memory management  

Science Conference Proceedings (OSTI)

A Dual-mode baseband (W-CDMA/HSDPA and GSM/GPRS/EDGE) and multimedia application processor SoC is described. The SoC fabricated in triple-Vth 65nm CMOS has 3 CPU cores and 20 separate power domains to achieve both high performance and low power. The ...

Tatsuya Kamei; Tetsuhiro Yamada; Takao Koike; Masayuki Ito; Takahiro Irita; Kenichi Nitta; Toshihiro Hattori; Shinichi Yoshioka

2009-01-01T23:59:59.000Z

4

Oxaliplatin Plus Dual Inhibition of Thymidilate Synthase During Preoperative Pelvic Radiotherapy for Locally Advanced Rectal Carcinoma: Long-Term Outcome  

Science Conference Proceedings (OSTI)

Purpose: To assess the safety and efficacy of oxaliplatin (OXA) plus dual inhibition of thymidilate synthase during preoperative pelvic radiotherapy (RT) in patients with poor prognosis for rectal carcinoma. Methods and Materials: Sixty-three patients with the following characteristics, a clinical (c) stage T4, cN1-2, or cT3N0 of {ve and ypN-ve) or minor or no response (TRG4 to -5, or ypCRM+ve, or ypN+ve). Adjuvant 5-FU/LFA regimen was given in cases of cT4, ypN+ve, or ypCRM+ve. Results: Overall, neutropenia (40%) and diarrhea (13%) were the most common grade {>=}3 toxicities, and tolerability was better with a 5-FU dose reduction. No significant difference in pathologic response was seen according 5-FU dosage: overall, a ypCR was obtained in 24 (39%) patients, and a major response in 20 (32%) patients. The 5-year probability of freedom from recurrence was 80% (95% confidence interval, 68%-92%); it was 56% for the minor/no response group, while it was around 90% for both the ypCR and the major response group. Conclusions: OXA, RTX, and 5-FU/LFA administered during pelvic RT produced promising early and long-term results in rectal carcinoma patients with poor prognosis. The postoperative treatment strategy applied in our study supports the risk-adapted approach in postoperative management.

Avallone, Antonio, E-mail: avalloneantonio@libero.i [Department of Gastrointestinal Medical Oncology, National Cancer Institute, Naples (Italy); Delrio, Paolo [Department of Surgery Oncology, National Cancer Institute, Naples (Italy); Pecori, Biagio [Department of Diagnostic Imaging and Radiotherapy, National Cancer Institute, Naples (Italy); Tatangelo, Fabiana [Department of Pathology, National Cancer Institute, Naples (Italy); Petrillo, Antonella [Department of Diagnostic Imaging and Radiotherapy, National Cancer Institute, Naples (Italy); Scott, Nigel [Department of Pathology, St. James University Hospital, Leeds (United Kingdom); Marone, Pietro [Department of Surgery Oncology, National Cancer Institute, Naples (Italy); Aloi, Luigi [Department of Diagnostic Imaging and Radiotherapy, National Cancer Institute, Naples (Italy); Sandomenico, Claudia [Department of Gastrointestinal Medical Oncology, National Cancer Institute, Naples (Italy); Lastoria, Secondo [Department of Diagnostic Imaging and Radiotherapy, National Cancer Institute, Naples (Italy); Iaffaioli, Vincenzo Rosario [Department of Gastrointestinal Medical Oncology, National Cancer Institute, Naples (Italy); Scala, Dario [Department of Surgery Oncology, National Cancer Institute, Naples (Italy); Iodice, Giovanni [Department of Gastrointestinal Medical Oncology, National Cancer Institute, Naples (Italy); Budillon, Alfredo [Department of Experimental Pharmacology, National Cancer Institute, Naples (Italy); Comella, Pasquale [Department of Gastrointestinal Medical Oncology, National Cancer Institute, Naples (Italy)

2011-03-01T23:59:59.000Z

5

Motif discovery in sequential data  

E-Print Network (OSTI)

In this thesis, I discuss the application and development of methods for the automated discovery of motifs in sequential data. These data include DNA sequences, protein sequences, and real-valued sequential data such as ...

Jensen, Kyle L. (Kyle Lawrence)

2006-01-01T23:59:59.000Z

6

Sequential cloning of chromosomes  

DOE Patents (OSTI)

A method for sequential cloning of chromosomal DNA and chromosomal DNA cloned by this method are disclosed. The method includes the selection of a target organism having a segment of chromosomal DNA to be sequentially cloned. A first DNA segment, having a first restriction enzyme site on either side. homologous to the chromosomal DNA to be sequentially cloned is isolated. A first vector product is formed by ligating the homologous segment into a suitably designed vector. The first vector product is circularly integrated into the target organism`s chromosomal DNA. The resulting integrated chromosomal DNA segment includes the homologous DNA segment at either end of the integrated vector segment. The integrated chromosomal DNA is cleaved with a second restriction enzyme and ligated to form a vector-containing plasmid, which is replicated in a host organism. The replicated plasmid is then cleaved with the first restriction enzyme. Next, a DNA segment containing the vector and a segment of DNA homologous to a distal portion of the previously isolated DNA segment is isolated. This segment is then ligated to form a plasmid which is replicated within a suitable host. This plasmid is then circularly integrated into the target chromosomal DNA. The chromosomal DNA containing the circularly integrated vector is treated with a third, retrorestriction enzyme. The cleaved DNA is ligated to give a plasmid that is used to transform a host permissive for replication of its vector. The sequential cloning process continues by repeated cycles of circular integration and excision. The excision is carried out alternately with the second and third enzymes.

Lacks, S.A.

1991-12-31T23:59:59.000Z

7

Sequential cloning of chromosomes  

DOE Patents (OSTI)

A method for sequential cloning of chromosomal DNA of a target organism is disclosed. A first DNA segment homologous to the chromosomal DNA to be sequentially cloned is isolated. The first segment has a first restriction enzyme site on either side. A first vector product is formed by ligating the homologous segment into a suitably designed vector. The first vector product is circularly integrated into the target organism's chromosomal DNA. The resulting integrated chromosomal DNA segment includes the homologous DNA segment at either end of the integrated vector segment. The integrated chromosomal DNA is cleaved with a second restriction enzyme and ligated to form a vector-containing plasmid, which is replicated in a host organism. The replicated plasmid is then cleaved with the first restriction enzyme. Next, a DNA segment containing the vector and a segment of DNA homologous to a distal portion of the previously isolated DNA segment is isolated. This segment is then ligated to form a plasmid which is replicated within a suitable host. This plasmid is then circularly integrated into the target chromosomal DNA. The chromosomal DNA containing the circularly integrated vector is treated with a third, retrorestriction (class IIS) enzyme. The cleaved DNA is ligated to give a plasmid that is used to transform a host permissive for replication of its vector. The sequential cloning process continues by repeated cycles of circular integration and excision. The excision is carried out alternately with the second and third enzymes.

Lacks, Sanford A. (Brookhaven, NY)

1995-07-18T23:59:59.000Z

8

Sequential cloning of chromosomes  

DOE Patents (OSTI)

A method for sequential cloning of chromosomal DNA of a target organism is disclosed. A first DNA segment homologous to the chromosomal DNA to be sequentially cloned is isolated. The first segment has a first restriction enzyme site on either side. A first vector product is formed by ligating the homologous segment into a suitably designed vector. The first vector product is circularly integrated into the target organism`s chromosomal DNA. The resulting integrated chromosomal DNA segment includes the homologous DNA segment at either end of the integrated vector segment. The integrated chromosomal DNA is cleaved with a second restriction enzyme and ligated to form a vector-containing plasmid, which is replicated in a host organism. The replicated plasmid is then cleaved with the first restriction enzyme. Next, a DNA segment containing the vector and a segment of DNA homologous to a distal portion of the previously isolated DNA segment is isolated. This segment is then ligated to form a plasmid which is replicated within a suitable host. This plasmid is then circularly integrated into the target chromosomal DNA. The chromosomal DNA containing the circularly integrated vector is treated with a third, retrorestriction (class IIS) enzyme. The cleaved DNA is ligated to give a plasmid that is used to transform a host permissive for replication of its vector. The sequential cloning process continues by repeated cycles of circular integration and excision. The excision is carried out alternately with the second and third enzymes. 9 figs.

Lacks, S.A.

1995-07-18T23:59:59.000Z

9

Dual photography  

Science Conference Proceedings (OSTI)

We present a novel photographic technique called dual photography, which exploits Helmholtz reciprocity to interchange the lights and cameras in a scene. With a video projector providing structured illumination, reciprocity permits us to generate pictures ... Keywords: dual photography, image synthesis, image-based relighting

Pradeep Sen; Billy Chen; Gaurav Garg; Stephen R. Marschner; Mark Horowitz; Marc Levoy; Hendrik P. A. Lensch

2005-07-01T23:59:59.000Z

10

A Globally Convergent Sequential Linear Programming Algorithm ...  

E-Print Network (OSTI)

approach, and a piecewise sequential quadratic programming approach (PSQP). Fukushima, Luo and Pang [20] proposed a sequential quadratic programming,...

11

Adaptive sequential controller  

Science Conference Proceedings (OSTI)

An adaptive sequential controller for controlling a circuit breaker or other switching device to substantially eliminate transients on a distribution line caused by closing and opening the circuit breaker. The device adaptively compensates for changes in the response time of the circuit breaker due to aging and environmental effects. A potential transformer provides a reference signal corresponding to the zero crossing of the voltage waveform, and a phase shift comparator circuit compares the reference signal to the time at which any transient was produced when the circuit breaker closed, producing a signal indicative of the adaptive adjustment that should be made. Similarly, in controlling the opening of the circuit breaker, a current transformer provides a reference signal that is compared against the time at which any transient is detected when the circuit breaker last opened. An adaptive adjustment circuit produces a compensation time that is appropriately modified to account for changes in the circuit breaker response, including the effect of ambient conditions and aging. When next opened or closed, the circuit breaker is activated at an appropriately compensated time, so that it closes when the voltage crosses zero and opens when the current crosses zero, minimizing any transients on the distribution line. Phase angle can be used to control the opening of the circuit breaker relative to the reference signal provided by the potential transformer. 15 figs.

El-Sharkawi, M.A.; Xing, J.; Butler, N.G.; Rodriguez, A.

1994-11-01T23:59:59.000Z

12

Adaptive sequential controller  

DOE Patents (OSTI)

An adaptive sequential controller (50/50') for controlling a circuit breaker (52) or other switching device to substantially eliminate transients on a distribution line caused by closing and opening the circuit breaker. The device adaptively compensates for changes in the response time of the circuit breaker due to aging and environmental effects. A potential transformer (70) provides a reference signal corresponding to the zero crossing of the voltage waveform, and a phase shift comparator circuit (96) compares the reference signal to the time at which any transient was produced when the circuit breaker closed, producing a signal indicative of the adaptive adjustment that should be made. Similarly, in controlling the opening of the circuit breaker, a current transformer (88) provides a reference signal that is compared against the time at which any transient is detected when the circuit breaker last opened. An adaptive adjustment circuit (102) produces a compensation time that is appropriately modified to account for changes in the circuit breaker response, including the effect of ambient conditions and aging. When next opened or closed, the circuit breaker is activated at an appropriately compensated time, so that it closes when the voltage crosses zero and opens when the current crosses zero, minimizing any transients on the distribution line. Phase angle can be used to control the opening of the circuit breaker relative to the reference signal provided by the potential transformer.

El-Sharkawi, Mohamed A. (Renton, WA); Xing, Jian (Seattle, WA); Butler, Nicholas G. (Newberg, OR); Rodriguez, Alonso (Pasadena, CA)

1994-01-01T23:59:59.000Z

13

Dual photography  

E-Print Network (OSTI)

Figure 1: (a) Conventional photograph of a scene, illuminated by a projector with all its pixels turned on. (b) After measuring the light transport between the projector and the camera using structured illumination, our technique is able to synthesize a photorealistic image from the point of view of the projector. This image has the resolution of the projector and is illuminated by a light source at the position of the camera. The technique can capture subtle illumination effects such as caustics and self-shadowing. Note, for example, how the glass bottle in the primal image (a) appears as the caustic in the dual image (b) and vice-versa. Because we have determined the complete light transport between the projector and camera, it is easy to relight the dual image using a synthetic light source (c) or a light modified by a matte captured later by the same camera (d). We present a novel photographic technique called dual photography, which exploits Helmholtz reciprocity to interchange the lights and cameras in a scene. With a video projector providing structured illumination, reciprocity permits us to generate pictures from the viewpoint of the projector, even though no camera was present at that location. The technique is completely image-based, requiring no knowledge of scene geometry or surface properties, and

Pradeep Sen; Billy Chen; Gaurav Garg; Stephen R. Marschner; Mark Horowitz; Marc Levoy; Hendrik P. A. Lensch

2005-01-01T23:59:59.000Z

14

Informative Views and Sequential Recognition  

E-Print Network (OSTI)

Informative Views and Sequential Recognition Tal Arbel and Frank P. Ferrie TR-CIM-95-10 Nov. 1995 3 Telephone: 514 398-6319 Telex: 05 268510 FAX: 514 398-7348 Email: cim@cim.mcgill.ca #12;Informative Views

Dudek, Gregory

15

On the Sequential Determination of Model Misfit  

E-Print Network (OSTI)

On the Sequential Determination of Model Misfit Peter Whaite and Frank P. Ferrie TR-CIM-94-6319 Telex: 05 268510 FAX: 514 398-7348 Email: cim@cim.mcgill.ca #12;On the Sequential Determination of Model

Dudek, Gregory

16

On the Sequential Determination of Model Misfit  

E-Print Network (OSTI)

On the Sequential Determination of Model Misfit Peter Whaite and Frank P. Ferrie TR­CIM­94) 398­6319 Telex: 05 268510 FAX: (514) 398­7348 Email: cim@cim.mcgill.ca #12; On the Sequential

Dudek, Gregory

17

Sequential Circuit Testing: From DFT to SFT  

Science Conference Proceedings (OSTI)

Sequential circuit testing is an active research area due to its applicability, its practicality, and its complexity. This paper gives an overview of the sequential automatic test pattern generation approaches and the classical and more recent design-for-testability ... Keywords: logic testing, sequential circuit testing, DFT techniques, automatic test pattern generation, design-for-testability methods, synthesis-for-testability, SFT techniques, large sequential circuits, ATPG

R. M. Chou; K. K. Saluja

1997-01-01T23:59:59.000Z

18

Using CSP to verify sequential consistency  

Science Conference Proceedings (OSTI)

This paper shows how the theory of Communicating Sequential Processes (CSP) can be used to establish that a protocol guarantees sequential consistency. The protocol in question is an accepted design based upon lazy caching; it is an ideal example for ... Keywords: CSP, lazy caching protocol, sequential consistency, specification, verification

Gavin Lowe; Jim Davies

1999-06-01T23:59:59.000Z

19

Sequential Monte Carlo for Bayesian sequentially designed experiments for discrete data  

Science Conference Proceedings (OSTI)

In this paper we present a sequential Monte Carlo algorithm for Bayesian sequential experimental design applied to generalised non-linear models for discrete data. The approach is computationally convenient in that the information of newly observed data ... Keywords: Clinical trials, Generalised linear model, Generalised non-linear model, Sequential Monte Carlo, Sequential design, Target stimulus

Christopher C. Drovandi; James M. Mcgree; Anthony N. Pettitt

2013-01-01T23:59:59.000Z

20

Sequential power-up circuit  

DOE Patents (OSTI)

A sequential power-up circuit for starting several electrical load elements in series to avoid excessive current surge, comprising a voltage ramp generator and a set of voltage comparators, each comparator having a different reference voltage and interfacing with a switch that is capable of turning on one of the load elements. As the voltage rises, it passes the reference voltages one at a time and causes the switch corresponding to that voltage to turn on its load element. The ramp is turned on and off by a single switch or by a logic-level electrical signal. The ramp rate for turning on the load element is relatively slow and the rate for turning the elements off is relatively fast. Optionally, the duration of each interval of time between the turning on of the load elements is programmable. 2 figs.

Kronberg, J.W.

1992-06-02T23:59:59.000Z

Note: This page contains sample records for the topic "advanced sequential dual" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


21

Sequential power-up circuit  

DOE Patents (OSTI)

A sequential power-up circuit for starting several electrical load elements in series to avoid excessive current surge, comprising a voltage ramp generator and a set of voltage comparators, each comparator having a different reference voltage and interfacing with a switch that is capable of turning on one of the load elements. As the voltage rises, it passes the reference voltages one at a time and causes the switch corresponding to that voltage to turn on its load element. The ramp is turned on and off by a single switch or by a logic-level electrical signal. The ramp rate for turning on the load element is relatively slow and the rate for turning the elements off is relatively fast. Optionally, the duration of each interval of time between the turning on of the load elements is programmable.

Kronberg, James W. (108 Independent Blvd., Aiken, SC 29801)

1992-01-01T23:59:59.000Z

22

Sequential detection of web defects  

DOE Patents (OSTI)

A system for detecting defects on a moving web having a sequential series of identical frames uses an imaging device to form a real-time camera image of a frame and a comparitor to comparing elements of the camera image with corresponding elements of an image of an exemplar frame. The comparitor provides an acceptable indication if the pair of elements are determined to be statistically identical; and a defective indication if the pair of elements are determined to be statistically not identical. If the pair of elements is neither acceptable nor defective, the comparitor recursively compares the element of said exemplar frame with corresponding elements of other frames on said web until one of the acceptable or defective indications occur.

Eichel, Paul H. (Albuquerque, NM); Sleefe, Gerard E. (Cedar Crest, NM); Stalker, K. Terry (Albuquerque, NM); Yee, Amy A. (Albuquerque, NM)

2001-01-01T23:59:59.000Z

23

Machine Learning for Sequential Data: A Review  

Science Conference Proceedings (OSTI)

Statistical learning problems in many fields involve sequential data. This paper formalizes the principal learning tasks and describes the methods that have been developed within the machine learning research community for addressing these problems. ...

Thomas G. Dietterich

2002-08-01T23:59:59.000Z

24

A comparison of sequential and simultaneous auctions  

Science Conference Proceedings (OSTI)

Sequential and simultaneous auctions are two important mechanisms for buying/selling multiple objects. These two mechanisms yield different outcomes (i.e., different revenues and also different profits to the winning bidders). Hence, both the auctioneer ...

Shaheen S. Fatima

2006-05-01T23:59:59.000Z

25

A view-sequential 3D display  

E-Print Network (OSTI)

This thesis outlines the various techniques for creating electronic 3D displays and analyzes their commercial potential. The thesis argues for the use of view-sequential techniques in the design of 3D displays based on ...

Cossairt, Oliver S. (Oliver Strider), 1978-

2003-01-01T23:59:59.000Z

26

Sequential versus simultaneous auctions: a case study  

Science Conference Proceedings (OSTI)

Sequential and simultaneous auctions are two important mechanisms for buying and selling multiple objects. These two mechanisms yield different outcomes (i.e., different surpluses, different revenues, and also different profits to the winning bidders). ... Keywords: game-theory, multi-object auctions

Shaheen Fatima

2006-08-01T23:59:59.000Z

27

NDSeq: runtime checking for nondeterministic sequential specifications of parallel correctness  

Science Conference Proceedings (OSTI)

We propose to specify the correctness of a program's parallelism using a sequential version of the program with controlled nondeterminism. Such a nondeterministic sequential specification allows (1) the correctness of parallel interference to ... Keywords: parallel correctness, serializability, specification

Jacob Burnim; Tayfun Elmas; George Necula; Koushik Sen

2011-06-01T23:59:59.000Z

28

Scalable Feature Mining for Sequential Data Mitsubishi Electric Research Lab.  

E-Print Network (OSTI)

Scalable Feature Mining for Sequential Data Neal Lesh Mitsubishi Electric Research Lab. 201, DNA sequences, web usage data, multi­player games, and plan execution traces. In sequential domains

Zaki, Mohammed Javeed

29

facial reduction and extended duals  

E-Print Network (OSTI)

Facial reduction and extended duals Here we study two fundamental approaches ...... denberghe, and Henry Wolkowicz, editors, Handbook of semidefinite...

30

Decoding sequential vs non-sequential two-photon double ionizationof helium using nuclear recoil  

SciTech Connect

Above 54.4 eV, two-photon double ionization of helium isdominated by a sequential absorption process, producing characteristicbehavior in the single and triple differential cross sections. We showthat the signature of this process is visible in the nuclear recoil crosssection, integrated over all energy sharings of the ejected electrons,even below the threshold for the sequential process. Since nuclear recoilmomentum imaging does not require coincident photoelectron measurement,the predicted images present a viable target for future experiments withnew short-pulse VUV and soft X-ray sources.

Horner, Daniel A.; Rescigno, Thomas N.; McCurdy, C. William

2008-01-07T23:59:59.000Z

31

Dual generalized Bernstein basis  

Science Conference Proceedings (OSTI)

The generalized Bernstein basis in the space @P"n of polynomials of degree at most n, being an extension of the q-Bernstein basis introduced by Philips [Bernstein polynomials based on the q-integers, Ann. Numer. Math. 4 (1997) 511-518], is given by the ... Keywords: Bernstein basis, Big q-Jacobi polynomials, Discrete Bernstein basis, Dual basis, Generalized Bernstein basis, Little q-Jacobi polynomials, Shifted Jacobi polynomials, q -Bernstein basis

Stanis?aw Lewanowicz; Pawe? Wo?ny

2006-02-01T23:59:59.000Z

32

Dual design resistor for high voltage conditioning and transmission lines  

DOE Patents (OSTI)

A dual resistor for eliminating the requirement for two different value resistors. The dual resistor includes a conditioning resistor at a high resistance value and a run resistor at a low resistance value. The run resistor can travel inside the conditioning resistor. The run resistor is capable of being advanced by a drive assembly until an electrical path is completed through the run resistor thereby shorting out the conditioning resistor and allowing the lower resistance run resistor to take over as the current carrier.

Siggins, Timothy Lynn (Newport News, VA); Murray, Charles W. (Hayes, VA); Walker, Richard L. (Norfolk, VA)

2007-01-23T23:59:59.000Z

33

Advanced Materials  

NLE Websites -- All DOE Office Websites (Extended Search)

Advanced Materials Advanced Materials Availability Technology Express Licensing Active Terahertz Metamaterial Devices Express Licensing Anion-Conducting Polymer, Composition, And...

34

SeQuential Pacific Biodiesel LLC | Open Energy Information  

Open Energy Info (EERE)

Pacific Biodiesel LLC Jump to: navigation, search Name SeQuential-Pacific Biodiesel LLC Place Oregon Sector Biofuels Product JV between SeQuential Biofuels, Pacific Biodiesel, and...

35

Sequential generation of matrix-product states in cavity QED  

Science Conference Proceedings (OSTI)

We study the sequential generation of entangled photonic and atomic multiqubit states in the realm of cavity QED. We extend the work of C. Schoen et al. [Phys. Rev. Lett. 95, 110503 (2005)], where it was shown that all states generated in a sequential manner can be classified efficiently in terms of matrix-product states. In particular, we consider two scenarios: photonic multiqubit states sequentially generated at the cavity output of a single-photon source and atomic multiqubit states generated by their sequential interaction with the same cavity mode.

Schoen, C. [Blackett Laboratory, Imperial College London, Prince Consort Road, London SW7 2BZ (United Kingdom); Hammerer, K. [Institute for Theoretical Physics, University of Innsbruck, 6020 Innsbruck (Austria); Wolf, M. M.; Cirac, J. I. [Max-Planck-Institut fuer Quantenoptik, Hans-Kopfermann-Strasse 1, 85748 Garching (Germany); Solano, E. [Physics Department, ASC, and CeNS, Ludwig-Maximilians-Universitaet, Theresienstrasse 37, 80333 Munich (Germany); Seccion Fisica, Departamento de Ciencias, Pontificia Universidad Catolica del Peru, Apartado Postal 1761, Lima (Peru)

2007-03-15T23:59:59.000Z

36

A robust geometry estimation method for spiral, sequential and circular cone-beam micro-CT  

Science Conference Proceedings (OSTI)

Purpose: The authors propose a novel method for misalignment estimation of micro-CT scanners using an adaptive genetic algorithm. Methods: The proposed algorithm is able to estimate the rotational geometry, the direction vector of table movement and the displacement between different imaging threads of a dual source or even multisource scanner. The calibration procedure does not rely on dedicated calibration phantoms and a sequence scan of a single metal bead is sufficient to geometrically calibrate the whole imaging system for spiral, sequential, and circular scan protocols. Dual source spiral and sequential scan protocols in micro-computed tomography result in projection data that-besides the source and detector positions and orientations-also require a precise knowledge of the table direction vector to be reconstructed properly. If those geometric parameters are not known accurately severe artifacts and a loss in spatial resolution appear in the reconstructed images as long as no geometry calibration is performed. The table direction vector is further required to ensure that consecutive volumes of a sequence scan can be stitched together and to allow the reconstruction of spiral data at all. Results: The algorithm's performance is evaluated using simulations of a micro-CT system with known geometry and misalignment. To assess the quality of the algorithm in a real world scenario the calibration of a micro-CT scanner is performed and several reconstructions with and without geometry estimation are presented. Conclusions: The results indicate that the algorithm successfully estimates all geometry parameters, misalignment artifacts in the reconstructed volumes vanish, and the spatial resolution is increased as can be shown by the evaluation of modulation transfer function measurements.

Sawall, Stefan; Knaup, Michael; Kachelriess, Marc [Institute of Medical Physics (IMP), University of Erlangen-Nuernberg, 91052 Erlangen (Germany); Institute of Medical Physics (IMP), University of Erlangen-Nuernberg, 91052 Erlangen (Germany) and Medical Physics in Radiology, German Cancer Research Center (DKFZ), Im Neuenheimer Feld 280, 69120 Heidelberg (Germany)

2012-09-15T23:59:59.000Z

37

Interim report Assessment of Baseline and Advanced Hydrogen Production...  

NLE Websites -- All DOE Office Websites (Extended Search)

Cycle Cases The IGCC design cases analyzed in this report are based on the power production from dual advanced F-class combined cycle gas turbines. The plants are nominally...

38

Generic sequential sampling for metamodel approximations  

SciTech Connect

Metamodels approximate complex multivariate data sets from simulations and experiments. These data sets often are not based on an explicitly defined function. The resulting metamodel represents a complex system's behavior for subsequent analysis or optimization. Often an exhaustive data search to obtain the data for the metalnodel is impossible, so an intelligent sampling strategy is necessary. While inultiple approaches have been advocated, the majority of these approaches were developed in support of a particular class of metamodel, known as a Kriging. A more generic, cotninonsense approach to this problem allows sequential sampling techniques to be applied to other types of metamodeis. This research compares recent search techniques for Kriging inetamodels with a generic, inulti-criteria approach combined with a new type of B-spline metamodel. This B-spline metamodel is competitive with prior results obtained with a Kriging metamodel. Furthermore, the results of this research highlight several important features necessary for these techniques to be extended to more complex domains.

Turner, C. J. (Cameron J.); Campbell, M. I. (Matthew I.)

2003-01-01T23:59:59.000Z

39

Precipitation Classification and Quantification Using X-band Dual-Polarization Weather Radar: Application in the Hydrometeorology Testbed  

Science Conference Proceedings (OSTI)

This paper presents new methods for rainfall estimation from X-band dual-polarization radar observations along with advanced techniques for quality control, hydrometeor classification, and estimation of specific differential phase. Data collected ...

S. Lim; R. Cifelli; V. Chandrasekar; S. Y. Matrosov

40

On probabilistic models for uncertain sequential pattern mining  

Science Conference Proceedings (OSTI)

We study uncertainty models in sequential pattern mining. We consider situations where there is uncertainty either about a source or an event. We show that both these types of uncertainties could be modelled using probabilistic databases, and give possible-worlds ... Keywords: mining uncertain data, novel algorithms for mining, probabilistic databases, sequential pattern mining, theoretical foundations of data mining.

Muhammad Muzammal; Rajeev Raman

2010-11-01T23:59:59.000Z

Note: This page contains sample records for the topic "advanced sequential dual" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


41

Dual battery system  

Science Conference Proceedings (OSTI)

A dual battery system is described, comprising: a primary first battery having a first open circuit voltage, the first battery including a first positive electrode, a first negative electrode, and a first electrolyte; a second battery having a second open circuit voltage less than the first open circuit voltage, the second battery including a second positive electrode, a second negative electrode, and a second electrolyte stored separately and isolated from the first electrolyte; a pair of positive and negative terminals; and electrical connections connecting the first and second batteries in parallel to the terminals so that, as current is drawn from the batteries, the amount of current drawn from each respective battery at a constant voltage level varies with the magnitude of the current.

Wruck, W.J.

1993-06-29T23:59:59.000Z

42

Dual Tank Fuel System  

DOE Patents (OSTI)

A dual tank fuel system has primary and secondary fuel tanks, with the primary tank including a filler pipe to receive fuel and a discharge line to deliver fuel to an engine, and with a balance pipe interconnecting the primary tank and the secondary tank. The balance pipe opens close to the bottom of each tank to direct fuel from the primary tank to the secondary tank as the primary tank is filled, and to direct fuel from the secondary tank to the primary tank as fuel is discharged from the primary tank through the discharge line. A vent line has branches connected to each tank to direct fuel vapor from the tanks as the tanks are filled, and to admit air to the tanks as fuel is delivered to the engine.

Wagner, Richard William (Albion, NY); Burkhard, James Frank (Churchville, NY); Dauer, Kenneth John (Avon, NY)

1999-11-16T23:59:59.000Z

43

Dual surface interferometer  

DOE Patents (OSTI)

A double-pass interferometer is provided which allows direct measurement of relative displacement between opposed surfaces. A conventional plane mirror interferometer may be modified by replacing the beam-measuring path cube-corner reflector with an additional quarterwave plate. The beam path is altered to extend to an opposed plane mirrored surface and the reflected beam is placed in interference with a retained reference beam split from dual-beam source and retroreflected by a reference cube-corner reflector mounted stationary with the interferometer housing. This permits direct measurement of opposed mirror surfaces by laser interferometry while doubling the resolution as with a conventional double-pass plane mirror laser interferometer system.

Pardue, R.M.; Williams, R.R.

1980-09-12T23:59:59.000Z

44

Dual surface interferometer  

DOE Patents (OSTI)

A double-pass interferometer is provided which allows direct measurement of relative displacement between opposed surfaces. A conventional plane mirror interferometer may be modified by replacing the beam-measuring path cube-corner reflector with an additional quarter-wave plate. The beam path is altered to extend to an opposed plane mirrored surface and the reflected beam is placed in interference with a retained reference beam split from dual-beam source and retroreflected by a reference cube-corner reflector mounted stationary with the interferometer housing. This permits direct measurement of opposed mirror surfaces by laser interferometry while doubling the resolution as with a conventional double-pass plane mirror laser interferometer system.

Pardue, Robert M. (Knoxville, TN); Williams, Richard R. (Oak Ridge, TN)

1982-01-01T23:59:59.000Z

45

Moral Hazard with Sequential Policy Making ?  

E-Print Network (OSTI)

We develop a moral hazard model of sequential policy making. Consistent with empirical observations, equilibrium behavior by the agent overemphasizes the late stages of the policy-making process. The reason is that the principal faces a kind of political time inconsistency problem because of the temptation to revise her retention rule in the middle of the policy-making process. If the principal knows the production technology for policy outcomes, then she can solve this time inconsistency problem (and the distortions it induces) by committing to task-specific budget caps. However, if the principal is uncertain about the production technology, such task-specific budget caps introduce ex post inefficiency. If the uncertainty is large enough, the principal may prefer an institutional environment where agent actions are non-transparent and the budget is fungible. Such an environment allows the principal to exploit the agents expertise about the production technology, but at the cost of weaker overall incentives. Hence, the model highlights a novel mechanism for why transparency may not always be optimal in political environments.

unknown authors

2013-01-01T23:59:59.000Z

46

Refactoring Sequential Java Code for Concurrency via Concurrent Libraries  

E-Print Network (OSTI)

Parallelizing existing sequential programs to run efficiently on multicores is hard. The Java 5 packagejava.util.concurrent (j.u.c.) supports writing concurrent programs: much of the complexity of writing threads-safe and ...

Ernst, Michael D.

2008-09-30T23:59:59.000Z

47

Dual Axis Radiographic Hydrodynamic Test Facility, IG-0599 |...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Administration Other Agencies You are here Home Dual Axis Radiographic Hydrodynamic Test Facility, IG-0599 Dual Axis Radiographic Hydrodynamic Test Facility, IG-0599 The Dual...

48

Advanced Materials for RSOFC Dual Operation with Low Degradation  

DOE Green Energy (OSTI)

Although this project is an open-ended development project, this effort, leveraging Versa Power Systems' years of development experience, has the potential to bring renewable energy RSOFC storage systems significantly closer to commercial viability through improvements in RSOFC durability, performance, and cost. When unitized and deployed in renewable solar and wind installations, an RSOFC system can enable higher availability for intermittent renewable resources, thereby improving the commercial viability of these types of energy resources.

Eric, Tang; Tony, Wood; Sofiane, Benhaddad; Casey, Brown; Hongpeng, He; Jeff, Nelson; Oliver, Grande; Ben, Nuttall; Mark, Richards; Randy, Petri

2012-12-27T23:59:59.000Z

49

Dual Heat Treat Process Development for Advanced Disk Applications  

Science Conference Proceedings (OSTI)

associated instrumentation details. ... The trials used an active air cooling fixture to control the .... in forging handling, and refinement of the control strategy.

50

UWB dual burst transmit driver  

SciTech Connect

A dual burst transmitter for ultra-wideband (UWB) communication systems generates a pair of precisely spaced RF bursts from a single trigger event. An input trigger pulse produces two oscillator trigger pulses, an initial pulse and a delayed pulse, in a dual trigger generator. The two oscillator trigger pulses drive a gated RF burst (power output) oscillator. A bias driver circuit gates the RF output oscillator on and off and sets the RF burst packet width. The bias driver also level shifts the drive signal to the level that is required for the RF output device.

Dallum, Gregory E. (Livermore, CA); Pratt, Garth C. (Discovery Bay, CA); Haugen, Peter C. (Livermore, CA); Zumstein, James M. (Livermore, CA); Vigars, Mark L. (Livermore, CA); Romero, Carlos E. (Livermore, CA)

2012-04-17T23:59:59.000Z

51

Photo of the Week: The First Energy-Efficient Dual-Paned Windows |  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

The First Energy-Efficient Dual-Paned Windows The First Energy-Efficient Dual-Paned Windows Photo of the Week: The First Energy-Efficient Dual-Paned Windows December 5, 2013 - 12:53pm Addthis Researchers at Berkeley Lab helped develop the first energy-efficient dual-paned windows, now used in buildings and homes worldwide for billions of dollars in energy savings. Current windows research in the Environmental Energy Technologies Division at Berkeley Lab is aimed at developing new glazing materials, windows simulation software and other advanced high-performance window systems. The building shown here, located at Berkeley Lab, is a windows testing facility. | Photo courtesy of Roy Kaltschmidt, Lawrence Berkeley National Laboratory. Researchers at Berkeley Lab helped develop the first energy-efficient

52

Dual function conducting polymer diodes  

DOE Patents (OSTI)

Dual function diodes based on conjugated organic polymer active layers are disclosed. When positively biased the diodes function as light emitters. When negatively biased they are highly efficient photodiodes. Methods of preparation and use of these diodes in displays and input/output devices are also disclosed.

Heeger, Alan J. (Santa Barbara, CA); Yu, Gang (Goleta, CA)

1996-01-01T23:59:59.000Z

53

Dual lookups in pattern databases  

Science Conference Proceedings (OSTI)

A pattern database (PDB) is a heuristic function stored as a lookup table. Symmetries of a state space are often used to enable multiple values to be looked up in a PDB for a given state. This paper introduces an additional PDB lookup, called the dual ...

Ariel Felner; Uzi Zahavi; Jonathan Schaeffer; Robert C. Holte

2005-07-01T23:59:59.000Z

54

SeQuential Biofuels LLC | Open Energy Information  

Open Energy Info (EERE)

SeQuential Biofuels LLC SeQuential Biofuels LLC Jump to: navigation, search Name SeQuential Biofuels LLC Place Portland, Oregon Zip 97231 Sector Biofuels Product A biofuels marketing and distribution company with several offices in Oregon. Coordinates 45.511795°, -122.675629° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":45.511795,"lon":-122.675629,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

55

Can Sequentially Linked Gamma-Ray Bursts Nullify Randomness?  

E-Print Network (OSTI)

In order to nullify the property of randomness perceived in the dispersion of gamma-ray bursts (GRB's) we introduce two new procedures. 1. Create a segmented group of sequentially linked GRB's and quantify the resultant angles. 2. Create segmented groups of sequentially linked GRB's in order to identify the location of GRB's that are positioned at equidistance, by using the selected GRB as the origin for a paired point circle, where the circumference of said circle intercepts the location of other GRB's in the same group.

Charles Fleischer

2012-05-02T23:59:59.000Z

56

Advanced Gasification  

NLE Websites -- All DOE Office Websites (Extended Search)

Advanced Gasification Carbon feedstock gasification is a promising pathway for high-efficiency, low-pollutant power generation and chemical production. The inability, however, to...

57

Advanced Ceramics  

Science Conference Proceedings (OSTI)

Table 3   Raw materials for advanced structural and magnetic (ferrite) ceramics...conductivity Wear resistance Oxygen sensors, fuel cells (potential), high-temperature

58

Advanced Manufacturing  

Science Conference Proceedings (OSTI)

... new metrologically-based methods for industry as well ... for Advanced Catalyst Development and Durability ... Electron-Beam Irradiation of Solar Cells. ...

2013-07-29T23:59:59.000Z

59

Online annotation of faces in personal videos by sequential learning  

Science Conference Proceedings (OSTI)

This paper addresses semi-automatic annotation of faces in personal videos. Different from previous offline annotation systems, this paper studies online annotation of faces. During an annotation session, few annotations are requested from the user only ... Keywords: Automatic annotation of faces, Personal video annotation, Sequential learning

M. C. Yilmazturk; I. Ulusoy; N. K. Cicekli

2013-04-01T23:59:59.000Z

60

Light-Weight Radioisotope Heater Unit (LWRHU) sequential impact tests  

SciTech Connect

The light-weight radioisotope heater unit (LWRHU) is a {sup 238}PuO{sub 2}-fueled heat source designed to provide one thermal watt in each of various locations on a spacecraft. Los Alamos National Laboratory designed, fabricated, and safety tested the LWRHU. The heat source consists of a hot-pressed {sup 238}PuO{sub 2} fuel pellet, a Pt-30Rh vented capsule, a pyrolytic graphite insulator, and a fineweave-pierced fabric graphite aeroshell assembly. A series of sequential impacts tests using simulant-fueled LWRHU capsules was recently conducted to determine a failure threshold. Sequential impacting, in both end-on and side-on orientations, resulted in increased damage with each subsequent impact. Although the tests were conducted until the aeroshells were sufficiently distorted to be out of dimensional specification, the simulant-fueled capsules used in these tests were not severely deformed. Sequential impacting of the LWRHU appears to result in slightly greater damage than a single impact at the final impact velocity of 50 m/s. Postimpact examination revealed that the sequentially impacted capsules were slightly more deformed and were outside of dimensional specifications.

Reimus, M.A.H.; Rinehart, G.H.

1997-08-01T23:59:59.000Z

Note: This page contains sample records for the topic "advanced sequential dual" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


61

Constraints of mixing matrix elements in the sequential fourthgeneration model  

E-Print Network (OSTI)

We review our works on the sequential fourth generation model and focus on the constriants of $4\\times 4$ quark mixing matrix elements. We investigate the quark mixing matrix elements from the rare $K,B$ meson decays. We talk about the $ hierarchy$ of the $4\\times 4$ matrix and the existence of fourth generation.

Huo, W J

2002-01-01T23:59:59.000Z

62

Functionalized sorbent for chemical separations and sequential forming process  

DOE Patents (OSTI)

A highly functionalized sorbent and sequential process for making are disclosed. The sorbent includes organic short-length amino silanes and organic oligomeric polyfunctional amino silanes that are dispersed within pores of a porous support that form a 3-dimensional structure containing highly functionalized active binding sites for sorption of analytes.

Fryxell, Glen E. (Kennewick, WA); Zemanian, Thomas S. (Richland, WA)

2012-03-20T23:59:59.000Z

63

Clustering and Sequential Pattern Mining of Online Collaborative Learning Data  

Science Conference Proceedings (OSTI)

Group work is widespread in education. The growing use of online tools supporting group work generates huge amounts of data. We aim to exploit this data to support mirroring: presenting useful high-level views of information about the group, together ... Keywords: Data mining, clustering, sequential pattern mining, learning group work skills, collaborative learning, computer-assisted instruction.

Dilhan Perera; Judy Kay; Irena Koprinska; Kalina Yacef; Osmar R. Zaane

2009-06-01T23:59:59.000Z

64

Dual Fluidized Bed Biomass Gasification  

DOE Green Energy (OSTI)

The dual fluidized bed reactor is a recirculating system in which one half of the unit operates as a steam pyrolysis device for biomass. The pyrolysis occurs by introducing biomass and steam to a hot fluidized bed of inert material such as coarse sand. Syngas is produced during the pyrolysis and exits the top of the reactor with the steam. A crossover arm, fed by gravity, moves sand and char from the pyrolyzer to the second fluidized bed. This sand bed uses blown air to combust the char. The exit stream from this side of the reactor is carbon dioxide, water and ash. There is a second gravity fed crossover arm to return sand to the pyrolysis side. The recirculating action of the sand and the char is the key to the operation of the dual fluidized bed reactor. The objective of the project was to design and construct a dual fluidized bed prototype reactor from literature information and in discussion with established experts in the field. That would be appropriate in scale and operation to measure the relative performance of the gasification of biomass and low ranked coals to produce a high quality synthesis gas with no dilution from nitrogen or combustion products.

None

2005-09-30T23:59:59.000Z

65

Sequential Infiltration Synthesis Advances Lithography (IN-10-017, 10-106)  

Lithography is widely used for defining patterns with high spatial resolution. In most applications of this technique, a thin-film polymeric resist material coating the substrate is patterned using light, electrons, or self-assembly. This resist film ...

66

Advanced Materials  

NLE Websites -- All DOE Office Websites (Extended Search)

Advanced Materials Advanced Materials Advanced Materials Express Licensing Active Terahertz Metamaterial Devices Express Licensing Anion-Conducting Polymer, Composition, And Membrane Express Licensing Analysis Of Macromolecule, Liggands And Macromolecule-Lingand Complexes Express Licensing Carbon Microtubes Express Licensing Chemical Synthesis Of Chiral Conducting Polymers Express Licensing Forming Adherent Coatings Using Plasma Processing Express Licensing Hydrogen Scavengers Express Licensing Laser Welding Of Fused Quartz Express Licensing Multiple Feed Powder Splitter Negotiable Licensing Boron-10 Neutron Detectors for Helium-3 Replacement Negotiable Licensing Insensitive Extrudable Explosive Negotiable Licensing Durable Fuel Cell Membrane Electrode Assembly (MEA) Express Licensing Method of Synthesis of Proton Conducting Materials

67

Single Inductor Dual Output Buck Converter  

E-Print Network (OSTI)

The portable electronics market is rapidly migrating towards more compact devices with multiple functionalities. Form factor, performance, cost and efficiency of these devices constitute the factors of merit of devices like cell phones, MP3 players and PDA's. With advancement in technology and more intelligent processors being used, there is a need for multiple high integrity voltage supplies for empowering the systems in portable electronic devices. Switched mode power supplies (SMPS's) are used to regulate the battery voltage. In an SMPS, maximum area is taken by the passive components such as the inductor and the capacitor. This work demonstrates a single inductor used in a buck converter with two output voltages from an input battery with voltage of value 3V. The main focus areas are low cross regulation between the outputs and supply of completely independent load current levels while maintaining desired values (1.2V,1.5V) within well controlled ripple levels. Dynamic hysteresis control is used for the single inductor dual output buck converter in this work. Results of schematic and post layout simulations performed in CADENCE prove the merits of this control method, such as nil cross regulation and excellent transient response.

Eachempatti, Haritha

2009-05-01T23:59:59.000Z

68

Dual Mode Inverter Control Test Verification  

SciTech Connect

Permanent Magnet Motors with either sinusoidal back emf (permanent magnet synchronous motor [PMSM]) or trapezoidal back emf (brushless dc motor [BDCM]) do not have the ability to alter the air gap flux density (field weakening). Since the back emf increases with speed, the system must be designed to operate with the voltage obtained at its highest speed. Oak Ridge National Laboratory's (ORNL) Power Electronics and Electric Machinery Research Center (PEEMRC) has developed a dual mode inverter controller (DMIC) that overcomes this disadvantage. This report summarizes the results of tests to verify its operation. The standard PEEMRC 75 kW hard-switched inverter was modified to implement the field weakening procedure (silicon controlled rectifier enabled phase advance). A 49.5 hp motor rated at 2800 rpm was derated to a base of 400 rpm and 7.5 hp. The load developed by a Kahn Industries hydraulic dynamometer, was measured with a MCRT9-02TS Himmelstein and Company torque meter. At the base conditions a current of 212 amperes produced the 7.5 hp. Tests were run at 400, 1215, and 2424 rpm. In each run, the current was no greater than 214 amperes. The horsepower obtained in the three runs were 7.5, 9.3, and 8.12. These results verified the basic operation of the DMIC in producing a Constant Power Speed Ratios (CPSR) of six.

Bailey, J.M.

2001-04-25T23:59:59.000Z

69

Advanced Ceramics  

Science Conference Proceedings (OSTI)

Table 2   Classification of advanced ceramics...solid electrolytes, piezoelectrics, dielectrics, superconductors Optical Low absorption coefficient Lamps, windows, fiber optics, infrared optics Nuclear Irradiation resistance, high absorption coefficient,

70

Advanced Manufacturing Office: Solicitations  

NLE Websites -- All DOE Office Websites (Extended Search)

Solicitations on Twitter Bookmark Advanced Manufacturing Office: Solicitations on Google Bookmark Advanced Manufacturing Office: Solicitations on Delicious Rank Advanced...

71

Advanced Manufacturing Office: Webcasts  

NLE Websites -- All DOE Office Websites (Extended Search)

Office: Webcasts on Twitter Bookmark Advanced Manufacturing Office: Webcasts on Google Bookmark Advanced Manufacturing Office: Webcasts on Delicious Rank Advanced...

72

Advanced Manufacturing Office: Subscribe  

NLE Websites -- All DOE Office Websites (Extended Search)

Office: Subscribe on Twitter Bookmark Advanced Manufacturing Office: Subscribe on Google Bookmark Advanced Manufacturing Office: Subscribe on Delicious Rank Advanced...

73

Advanced Manufacturing Office: Workshops  

NLE Websites -- All DOE Office Websites (Extended Search)

Office: Workshops on Twitter Bookmark Advanced Manufacturing Office: Workshops on Google Bookmark Advanced Manufacturing Office: Workshops on Delicious Rank Advanced...

74

Sequential circuit design for radiation hardened multiple voltage integrated circuits  

DOE Patents (OSTI)

The present invention includes a radiation hardened sequential circuit, such as a bistable circuit, flip-flop or other suitable design that presents substantial immunity to ionizing radiation while simultaneously maintaining a low operating voltage. In one embodiment, the circuit includes a plurality of logic elements that operate on relatively low voltage, and a master and slave latches each having storage elements that operate on a relatively high voltage.

Clark, Lawrence T. (Phoenix, AZ); McIver, III, John K. (Albuquerque, NM)

2009-11-24T23:59:59.000Z

75

Dual valve well pump installation  

SciTech Connect

A reciprocating electric motor-pump assembly for lifting well fluid on downstroke of the motor pump assembly, the pump including a barrel below the motor having dual combined inlet and outlet valve means at the lower end thereof, the pump piston moving in the barrel having annular grooves therearound to prevent differential pressure sticking, the electric cable supplying the electric motor being tubular to vent the pump and prevent vacuum or gas lock, there being a packer about the valve barrel separating the outlet valve means thereabove from the inlet valve means therebelow and a packer above the motor about a production tubing including an upper standing valve.

Holm, D. R.

1985-10-22T23:59:59.000Z

76

Sequential Importance Sampling for Rare Event Estimation with Computer Experiments  

SciTech Connect

Importance sampling often drastically improves the variance of percentile and quantile estimators of rare events. We propose a sequential strategy for iterative refinement of importance distributions for sampling uncertain inputs to a computer model to estimate quantiles of model output or the probability that the model output exceeds a fixed or random threshold. A framework is introduced for updating a model surrogate to maximize its predictive capability for rare event estimation with sequential importance sampling. Examples of the proposed methodology involving materials strength and nuclear reactor applications will be presented. The conclusions are: (1) Importance sampling improves UQ of percentile and quantile estimates relative to brute force approach; (2) Benefits of importance sampling increase as percentiles become more extreme; (3) Iterative refinement improves importance distributions in relatively few iterations; (4) Surrogates are necessary for slow running codes; (5) Sequential design improves surrogate quality in region of parameter space indicated by importance distributions; and (6) Importance distributions and VRFs stabilize quickly, while quantile estimates may converge slowly.

Williams, Brian J. [Los Alamos National Laboratory; Picard, Richard R. [Los Alamos National Laboratory

2012-06-25T23:59:59.000Z

77

Advanced Systems  

NLE Websites -- All DOE Office Websites (Extended Search)

Advanced Systems: Advanced Systems: high Performance fenestration systems Research areas: Research activities to improve the performance of windows and other fenestration products must address window systems issues as well as Glazing Materials research. LBNL activities in the area of Advanced Systems include research at both the product level and the building envelope and building systems levels. Highly insulating windows - using non structural center layers Lower cost solutions to more insulating three layer glazing systems, with the potential to turn windows in U.S. heating dominated residential applications into net-energy gainers. Highly Insulating Window Frames In collaboration with the Norwegian University of Science and Technology, we are researching the potentials for highly insulating window frames. Our initial work examines European frames with reported U-factors under 0.15 Btu/hr-ft2-F. Future research aims to analyze these designs, verify these performance levels and ensure that procedures used to calculate frame performance are accurate.

78

Dual extragradient algorithms extended to equilibrium problems  

Science Conference Proceedings (OSTI)

In this paper we propose two iterative schemes for solving equilibrium problems which are called dual extragradient algorithms. In contrast with the primal extragradient methods in Quoc et al. (Optimization 57(6):749---776, 2008) which require ... Keywords: Complexity, Dual extragradient algorithm, Equilibrium problem, Gap function, Nash-Cournot equilibria

Tran D. Quoc; Pham N. Anh; Le D. Muu

2012-01-01T23:59:59.000Z

79

DOE Guidance-Approval Process for Dual Compensation Waivers for...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Approval Process for Dual Compensation Waivers for Reemployed Annuitants DOE Guidance-Approval Process for Dual Compensation Waivers for Reemployed Annuitants Guidance Memorandum...

80

Dual manifold heat pipe evaporator  

DOE Patents (OSTI)

An improved evaporator section is described for a dual manifold heat pipe. Both the upper and lower manifolds can have surfaces exposed to the heat source which evaporate the working fluid. The tubes in the tube bank between the manifolds have openings in their lower extensions into the lower manifold to provide for the transport of evaporated working fluid from the lower manifold into the tubes and from there on into the upper manifold and on to the condenser portion of the heat pipe. A wick structure lining the inner walls of the evaporator tubes extends into both the upper and lower manifolds. At least some of the tubes also have overflow tubes contained within them to carry condensed working fluid from the upper manifold to pass to the lower without spilling down the inside walls of the tubes. 1 figure.

Adkins, D.R.; Rawlinson, K.S.

1994-01-04T23:59:59.000Z

Note: This page contains sample records for the topic "advanced sequential dual" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


81

Quantum dynamics in dual spaces  

Science Conference Proceedings (OSTI)

Quantum mechanics gives us information about spectra of dynamical variables and transition rates including scattering cross sections. They can be exhibited as spectral information in analytically continued spaces and their duals. Quantum mechanics formulated in these generalized spaces is used to study scattering and time evolution. It is shown that the usual asymptotic condition is inadequate to deal with scattering of composite or unstable particles. Scattering theory needs amendment when the interacting system is not isospectral with the free Hamiltonian, and the amendment is formulated. Perturbation theory in generalized spaces is developed and used to study the deletion and augmentation of the spectrum of the Hamiltonian. A complete set of algebraically independent constants for an interacting system is obtained. The question of the breaking of time symmetry is discussed.

Sudarshan, E.C.G.

1993-12-31T23:59:59.000Z

82

Dual manifold heat pipe evaporator  

DOE Patents (OSTI)

An improved evaporator section for a dual manifold heat pipe. Both the upper and lower manifolds can have surfaces exposed to the heat source which evaporate the working fluid. The tubes in the tube bank between the manifolds have openings in their lower extensions into the lower manifold to provide for the transport of evaporated working fluid from the lower manifold into the tubes and from there on into the upper manifold and on to the condenser portion of the heat pipe. A wick structure lining the inner walls of the evaporator tubes extends into both the upper and lower manifolds. At least some of the tubes also have overflow tubes contained within them to carry condensed working fluid from the upper manifold to pass to the lower without spilling down the inside walls of the tubes.

Adkins, Douglas R. (Albuquerque, NM); Rawlinson, K. Scott (Albuquerque, NM)

1994-01-01T23:59:59.000Z

83

Advanced Search  

NLE Websites -- All DOE Office Websites (Extended Search)

Publications Publications Advanced Search Most publications by Environmental Energy Technologies Division authors are searchable from this page, including peer-reviewed publications, book chapters, conference proceedings and LBNL reports. Filter Advanced Search Publications list This publications database is an ongoing project, and not all Division publications are represented here yet. For additional help see the bottom of this page. Documents Found: 4418 Title Keyword LBNL Number Author - Any - Abadie, Marc O Abbey, Chad Abdolrazaghi, Mohamad Aberg, Annika Abhyankar, Nikit Abraham, Marvin M Abshire, James B Abushakra, Bass Acevedo-Ruiz, Manuel Aceves, Salvador Ache, Hans J Ackerly, David D Ackerman, Andrew S Adamkiewicz, Gary Adams, J W Adams, Carl Adamson, Bo Addy, Nathan Addy, Susan E Aden, Nathaniel T Adesola, Bunmi Adhikari,

84

Advanced Combustion  

NLE Websites -- All DOE Office Websites (Extended Search)

Systems Systems Advanced Combustion Background Conventional coal-fired power plants utilize steam turbines to generate electricity, which operate at efficiencies of 35-37 percent. Operation at higher temperatures and pressures can lead to higher efficiencies, resulting in reduced fuel consumption and lower greenhouse gas emissions. Higher efficiency also reduces CO2 production for the same amount of energy produced, thereby facilitating a reduction in greenhouse gas emissions. When combined, oxy-combustion comes with an efficiency hit, so it will actually increase the amount of CO2 to be captured. But without so much N2 in the flue gas, it will be easier and perhaps more efficient to capture, utilize and sequester. NETL's Advanced Combustion Project and members of the NETL-Regional University

85

A sequential growth dynamics for a directed acyclic dyadic graph  

E-Print Network (OSTI)

A model of discrete spacetime on a microscopic level is considered. It is a directed acyclic dyadic graph. This is the particular case of a causal set. The goal of this model is to describe particles as some repetitive symmetrical self-organized structures of the graph without any reference to continuous spacetime. The dynamics of the model is considered. This dynamics is stochastic sequential additions of new vertexes. Growth of the graph is a Markovian process. This dynamics is a consequence of a causality principle.

Alexey L. Krugly

2011-12-05T23:59:59.000Z

86

Optimal sequential transmission over broadcast channel with nested feedback  

E-Print Network (OSTI)

We consider the optimal design of sequential transmission over broadcast channel with nested feedback. Nested feedback means that the channel output of the outer channel is also available at the decoder of the inner channel. We model the communication system as a decentralized team with three decision makers---the encoder and the two decoders. Structure of encoding and decoding strategies that minimize a total distortion measure over a finite horizon are determined. The results are applicable for real-time communication as well as for the information theoretic setup.

Mahajan, Aditya

2010-01-01T23:59:59.000Z

87

Advanced Combustion  

Science Conference Proceedings (OSTI)

The activity reported in this presentation is to provide the mechanical and physical property information needed to allow rational design, development and/or choice of alloys, manufacturing approaches, and environmental exposure and component life models to enable oxy-fuel combustion boilers to operate at Ultra-Supercritical (up to 650{degrees}C & between 22-30 MPa) and/or Advanced Ultra-Supercritical conditions (760{degrees}C & 35 MPa).

Holcomb, Gordon R. [NETL

2013-03-11T23:59:59.000Z

88

Performance Analysis of Dual-Fan, Dual-Duct Constant Volume Air-Handling Units  

E-Print Network (OSTI)

Dual-fan, dual-duct air-handling units introduce outside air directly into the cooling duct and use two variable speed devices to independently maintain the static pressure of the hot and the cold air ducts. Analytical models have been developed to compare fan power and thermal energy consumption of dualfan, dual-duct constant volume air-handling units with single-fan, dual-duct constant volume airhandling units. This study shows that the dual-fan, dual-duct system uses less fan power and less thermal energy during winter, and uses more thermal energy during summer. Thermal energy performance can be significantly improved if the thermal energy penalty can be decreased or eliminated.

Joo, I. S.; Liu, M.

2001-01-01T23:59:59.000Z

89

Advanced Energy Storage Publications  

NLE Websites -- All DOE Office Websites (Extended Search)

Advanced Energy Storage Publications Reports: Advanced Technology Development Program For Lithium-Ion Batteries: Gen 2 Performance Evaluation Final Report Advanced Technology...

90

Advanced Manufacturing Office: News  

NLE Websites -- All DOE Office Websites (Extended Search)

Manufacturing Office: News on Twitter Bookmark Advanced Manufacturing Office: News on Google Bookmark Advanced Manufacturing Office: News on Delicious Rank Advanced Manufacturing...

91

Advanced Research  

NLE Websites -- All DOE Office Websites (Extended Search)

Ductility EnhancEmEnt of molybDEnum Ductility EnhancEmEnt of molybDEnum PhasE by nano-sizED oxiDE DisPErsions Description Using computational modeling techniques, this research aims to develop predictive capabilities to facilitate the design and optimization of molybdenum (Mo), chromium (Cr), and other high-temperature structural materials to enable these materials to withstand the harsh environments of advanced power generation systems, such as gasification-based systems. These types of materials are essential to the development of highly efficient, clean energy technologies such as low-emission power systems that use coal or other fossil fuels.

92

Advanced Research  

NLE Websites -- All DOE Office Websites (Extended Search)

Super HigH-TemperaTure alloyS and Super HigH-TemperaTure alloyS and CompoSiTeS From nb-W-Cr SySTemS Description The U.S. Department of Energy's Office of Fossil Energy (DOE-FE) has awarded a three-year grant to the University of Texas at El Paso (UTEP) and Argonne National Laboratory (ANL) to jointly explore the high-temperature properties of alloys composed of niobium (Nb), tungsten (W), and chromium (Cr). The grant is administered by the Advanced Research (AR) program of the National

93

Mission Advancing  

NLE Websites -- All DOE Office Websites (Extended Search)

NETL Accomplishments NETL Accomplishments - the lab 2 Mission Advancing energy options to fuel our economy, strengthen our security, and improve our environment. Renewed Prosperity Through Technological Innovation - Letter from the Director NETL: the ENERGY lab 4 6 3 Contents Technology Transfer Patents and Commercialization Sharing Our Expertise Noteworthy Publications 60 62 63 64 66 Environment, Economy, & Supply Carbon Capture and Storage Partnerships Work to Reduce Atmospheric CO 2 Demand-Side Efficiencies New NETL Facility Showcases Green Technologies Environment & Economy Materials Mercury Membranes NETL Education Program Produces Significant Achievement Monitoring Water Economy & Supply NETL's Natural Gas Prediction Tool Aids Hurricane Recovery Energy Infrastructure

94

Dual-Reality Objects Randall B. Smith  

E-Print Network (OSTI)

with each IUG. To move dual-reality object A into the virtual world, the IUG notifies the LOM of the RIFD that DROID and that RIFD tag value. Ownership of the object is passed directly from the originating LOM

Redmiles, David F.

95

The Synthetic Dual-Doppler Analysis Technique  

Science Conference Proceedings (OSTI)

Synthetic dual-Doppler (SDD) is a single-Doppler analysis technique that combines measurements from two different times, provided the viewing angle changes significantly. In this study, the viability of the SDD technique is investigated through ...

Brian A. Klimowski; John D. Marwitz

1992-12-01T23:59:59.000Z

96

A single inductor dual input dual output DC-DC converter with hybrid supplies for solar energy harvesting applications  

Science Conference Proceedings (OSTI)

A single inductor dual input dual output (SIDIDO) DC-DC converter is proposed for solar energy harvesting applications. The converter supports hybrid power supplies from both the photovoltaic (PV) cells and the rechargeable battery. Apart from the conventional ... Keywords: DC-DC converter, MPPT, PV cells, dual-input-dual-output, energy harvesting, single inductor

Hui Shao; Chi-Ying Tsui; Wing-Hung Ki

2009-08-01T23:59:59.000Z

97

Dual control active superconductive devices  

DOE Patents (OSTI)

A superconducting active device has dual control inputs and is constructed such that the output of the device is effectively a linear mix of the two input signals. The device is formed of a film of superconducting material on a substrate and has two main conduction channels, each of which includes a weak link region. A first control line extends adjacent to the weak link region in the first channel and a second control line extends adjacent to the weak link region in the second channel. The current flowing from the first channel flows through an internal control line which is also adjacent to the weak link region of the second channel. The weak link regions comprise small links of superconductor, separated by voids, through which the current flows in each channel. Current passed through the control lines causes magnetic flux vortices which propagate across the weak link regions and control the resistance of these regions. The output of the device taken across the input to the main channels and the output of the second main channel and the internal control line will constitute essentially a linear mix of the two input signals imposed on the two control lines. The device is especially suited to microwave applications since it has very low input capacitance, and is well suited to being formed of high temperature superconducting materials since all of the structures may be formed coplanar with one another on a substrate.

Martens, Jon S. (Albuquerque, NM); Beyer, James B. (Madison, WI); Nordman, James E. (Madison, WI); Hohenwarter, Gert K. G. (Madison, WI)

1993-07-20T23:59:59.000Z

98

Advanced Research  

NLE Websites -- All DOE Office Websites (Extended Search)

05/2007 05/2007 NitrogeN evolutioN aNd CorrosioN MeChaNisMs With oxyCoMbustioN of Coal Description Under a grant from the University Coal Research (UCR) program, Brigham Young University (BYU) is leading a three-year research effort to investigate the physical processes that several common types of coal undergo during oxy-fuel combustion. Specifically, research addresses the mixture of gases emitted from burning, particularly such pollutants as nitrogen oxides (NO X ) and carbon dioxide (CO 2 ), and the potential for corrosion at the various stages of combustion. The UCR program is administered by the Advanced Research Program at the National Energy Technology Laboratory (NETL), under the U.S. Department of Energy's Office of

99

Dual-K Versus Dual-T Technique for Gate Leakage Reduction: A Comparative Perspective  

Science Conference Proceedings (OSTI)

As a result of aggressive technology scaling, gate leakage (gate oxide direct tunneling) has become a major component of total power dissipation. Use of dielectrics of higher permittivity (Dual-K) or use of silicon dioxide of higher thicknesses (Dual-T ...

Saraju P. Mohanty; Ramakrishna Velagapudi; Elias Kougianos

2006-03-01T23:59:59.000Z

100

Dual-speed wind turbine generation  

SciTech Connect

Induction generator has been used since the early development of utility-scale wind turbine generation. An induction generator is the generator of choice because of its ruggedness and low cost. With an induction generator, the operating speed of the wind turbine is limited to a narrow range (almost constant speed). Dual- speed operation can be accomplished by using an induction generator with two different sets of winding configurations or by using a dual output drive train to drive two induction generators with two different rated speeds. With single-speed operation, the wind turbine operates at different power coefficients (Cp) as the wind speed varies. Operation at maximum Cp can occur only at a single wind speed. However, if the wind speed.varies across a wider range, the operating Cp will vary significantly. Dual-speed operation has the advantage of enabling the wind turbine to operate at near maximum Cp over a wider range of wind speeds. Thus, annual energy production can be increased. The dual-speed mode may generate less energy than a variable-speed mode; nevertheless, it offers an alternative which captures more energy than single-speed operation. In this paper, dual-speed operation of a wind turbine is investigated. Annual energy production is compared between single-speed and dual-speed operation. One type of control algorithm for dual-speed operation is proposed. Some results from a dynamic simulation will be presented to show how the control algorithm works as the wind turbine is exposed to varying wind speeds.

Muljadi, E.; Butterfield, C.P. [National Renewable Energy Lab., Golden, CO (United States); Handman, D. [Flowind Corp., San Rafael, CA (United States)

1996-10-01T23:59:59.000Z

Note: This page contains sample records for the topic "advanced sequential dual" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


101

Dual control active superconductive devices  

Science Conference Proceedings (OSTI)

A dual control active superconducting device is described comprising; (a) a first device having a first main conduction channel formed of a film of superconductor on a substrate, an active weak link region interposed in the first main conduction channel, the active weak link region composed of a plurality of links formed of a thin film of superconductor separated by non-superconductive voids, the thickness and lateral dimensions of the links selected such that magnetic flux can propagate across the weak link region when it is superconducting, and a first control line having a portion adjacent to the active weak link region of the first main conduction channel such that current in the first control line will impose a magnetic flux on the weak link region; (b) a second superconducting device having a second main conduction channel formed of a film of superconductor on a substrate, an active weak link region interposed in the second main conduction channel, the active weak link region composed of at least one link formed of a thin film of superconductor separated by non-superconductive voids, the thickness and lateral dimensions of the links selected such that magnetic flux can propagate across the weak link region when it is superconducting, and a second control line having a portion adjacent to the active weak link region such that current in the second control line will impose a magnetic flux on the weak link region in the second main conduction channel; (c) an internal control line electrically connected to receive the current passed through the first main conduction channel and having a portion adjacent to the active weak link region of the second main conduction channel such that a current in the internal control line will impose a magnetic flux on the weak link region; and (d) electrical connectors connected to provide input current to the first and second main conduction channels and to conduct the output current.

Martens, J.S.; Beyer, J.B.; Nordman, J.E.; Hohenwarter, G.K.G.

1993-07-20T23:59:59.000Z

102

Sequentially linear analysis of shear critical reinforced concrete beams without shear reinforcement  

Science Conference Proceedings (OSTI)

Analyzing brittle structures with nonlinear finite element analysis is frequently attended with numerical problems. As an alternative method sequentially linear analysis could be utilized, resulting in the avoidance of convergence and bifurcation problems. ... Keywords: Brittle failure behavior, Cracking, Reinforced concrete, Sequentially linear analysis, Shear critical beam, Shear retention

A. T. Slobbe; M. A. N. Hendriks; J. G. Rots

2012-03-01T23:59:59.000Z

103

Efficiently speeding up sequential computation through the n-way programming model  

Science Conference Proceedings (OSTI)

With core counts on the rise, the sequential components of applications are becoming the major bottleneck in performance scaling as predicted by Amdahl's law. We are therefore faced with the simultaneous problems of occupying an increasing number of ... Keywords: algorithmic diversity, n-way, parallel programming model, sequential computations, speedup

Romain E. Cledat; Tushar Kumar; Santosh Pande

2011-10-01T23:59:59.000Z

104

Warped K-Means: An algorithm to cluster sequentially-distributed data  

Science Conference Proceedings (OSTI)

Many devices generate large amounts of data that follow some sort of sequentiality, e.g., motion sensors, e-pens, eye trackers, etc. and often these data need to be compressed for classification, storage, and/or retrieval tasks. Traditional clustering ... Keywords: Data compression, Data simplification, Partitional clustering, Sequential data, Trajectory segmentation

Luis A. Leiva, Enrique Vidal

2013-07-01T23:59:59.000Z

105

A module-level three-stage approach to the evolutionary design of sequential logic circuits  

Science Conference Proceedings (OSTI)

In this study, we propose a module-level three-stage approach (TSA) to optimize the evolutionary design for synchronous sequential circuits. TSA has a three stages process, involving a genetic algorithm (GA), a pre-evolution, and a re-evolution. In the ... Keywords: Data mining, Evolutionary approach, Frequently evolved blocks, Module-level, Redundant states, Sequential circuits, Three-stage

Yanyun Tao; Yuzhen Zhang; Jian Cao; Yalong Huang

2013-06-01T23:59:59.000Z

106

Brief Communication: Design of multiplex PCR primers using heuristic algorithm for sequential deletion applications  

Science Conference Proceedings (OSTI)

The sequential deletion method is commonly applied to locate the functional domain of a protein. Unfortunately, manually designing primers for multiplex polymerase chain reaction (PCR) is a labor-intensive task. In order to speed up the experimental ... Keywords: Multiplex polymerase chain reaction (PCR), N-terminal truncated mutants, Polyacrylamide gel electrophoresis (PAGE), Sequential deletion

Yung-Fu Chen; Rung-Ching Chen; Yung-Kuan Chan; Ren-Hao Pan; You-Cheng Hseu; Elong Lin

2009-04-01T23:59:59.000Z

107

Low Swing Dual Threshold Voltage Domino Logic  

E-Print Network (OSTI)

A low swing domino logic technique is proposed to decrease power consumption without sacrificing noise immunity. With the proposed low swing domino logic circuit technique, active power consumption is reduced by up to 9.4% while improving the noise immunity by 2.6% as compared to standard domino logic circuits. It is also shown that by applying a low swing contention reduction technique, the power savings can be further increased by 6.7% while the delay can be improved by 8.6%. A simple and efficient dual threshold voltage (dual-V t ) circuit technique that incorporates low swing signals is also proposed. It is shown that the proposed dual-V technique reduces the standby leakage current by approximately 235 times while offering enhanced delay characteristics as compared to a standard low threshold voltage implementation.

Volkan Kursun; Eby G. Friedman

2002-01-01T23:59:59.000Z

108

Dual Superconductivity in G2 group  

E-Print Network (OSTI)

We investigate the dual superconductivity mechanism in the exceptional group $G_2$. This is a centerless group (no 't Hooft flux vortices are allowed) and we check for the presence of a magnetic monopole condensate in the confined phase by measuring on the lattice a disorder parameter related to the vacuum expectation value of an operator carrying magnetic charge. The behaviour of the disorder parameter is consistent with the dual superconductor picture. A first step of an analysis on the thermodynamical properties of the theory is conducted by mean of this operator.

G. Cossu; M. D'Elia; A. Di Giacomo; B. Lucini; C. Pica

2006-09-28T23:59:59.000Z

109

Dual-Polarization Radar Characteristics of an Apartment Fire  

Science Conference Proceedings (OSTI)

Dual-polarimetric microwave wavelength radar observations of an apartment fire in Huntsville, Alabama, on 3 March 2008 are examined to determine the radar-observable properties of ash and fire debris lofted into the atmosphere. Dual-polarimetric ...

Thomas A. Jones; Sundar A. Christopher; Walt Petersen

2009-10-01T23:59:59.000Z

110

Use of Dual-Wavelength Radar for Snow Parameter Estimates  

Science Conference Proceedings (OSTI)

Use of dual-wavelength radar, with properly chosen wavelengths, will significantly lessen the ambiguities in the retrieval of microphysical properties of hydrometeors. In this paper, a dual-wavelength algorithm is described to estimate the ...

Liang Liao; Robert Meneghini; Toshio Iguchi; Andrew Detwiler

2005-10-01T23:59:59.000Z

111

GRADIENT INDEX SPHERES BY THE SEQUENTIAL ACCRETION OF GLASS POWDERS  

Science Conference Proceedings (OSTI)

The Department of Energy is seeking a method for fabricating mm-scale spheres having a refractive index that varies smoothly and continuously from the center to its surface [1]. The fabrication procedure must allow the creation of a range of index profiles. The spheres are to be optically transparent and have a refractive index differential greater than 0.2. The sphere materials can be either organic or inorganic and the fabrication technique must be capable of scaling to low cost production. Mo-Sci Corporation proposed to develop optical quality gradient refractive index (GRIN) glass spheres of millimeter scale (1 to 2 mm diameter) by the sequential accretion and consolidation of glass powders. Other techniques were also tested to make GRIN spheres as the powder-accretion method produced non-concentric layers and poor optical quality glass spheres. Potential ways to make the GRIN spheres were (1) by "coating" glass spheres (1 to 2 mm diameter) with molten glass in a two step process; and (2) by coating glass spheres with polymer layers.

MARIANO VELEZ

2008-06-15T23:59:59.000Z

112

Combined search for the quarks of a sequential fourth generation  

E-Print Network (OSTI)

Results are presented from a search for a fourth generation of quarks produced singly or in pairs in a data set corresponding to an integrated luminosity of 5 inverse femtobarns recorded by the CMS experiment at the LHC in 2011. A novel strategy has been developed for a combined search for quarks of the up- and down-type in decay channels with at least one isolated muon or electron. Limits on the mass of the fourth-generation quarks and the relevant CKM matrix elements are derived in the context of a simple extension of the standard model with a sequential fourth generation of fermions. The existence of mass-degenerate fourth-generation quarks with masses below 685 GeV is excluded at 95% confidence level for minimal off-diagonal mixing between the third- and the fourth-generation quarks. With a mass difference of 25 GeV between the quark masses, the obtained limit on the masses of the fourth-generation quarks shifts by about +/- 20 GeV. This result significantly reduces the allowed parameter space for a fourt...

Chatrchyan, Serguei; Sirunyan, Albert M; Tumasyan, Armen; Adam, Wolfgang; Aguilo, Ernest; Bergauer, Thomas; Dragicevic, Marko; Er, Janos; Fabjan, Christian; Friedl, Markus; Fruehwirth, Rudolf; Ghete, Vasile Mihai; Hammer, Josef; Hrmann, Natascha; Hrubec, Josef; Jeitler, Manfred; Kiesenhofer, Wolfgang; Knnz, Valentin; Krammer, Manfred; Krtschmer, Ilse; Liko, Dietrich; Mikulec, Ivan; Pernicka, Manfred; Rahbaran, Babak; Rohringer, Christine; Rohringer, Herbert; Schfbeck, Robert; Strauss, Josef; Taurok, Anton; Waltenberger, Wolfgang; Walzel, Gerhard; Widl, Edmund; Wulz, Claudia-Elisabeth; Mossolov, Vladimir; Shumeiko, Nikolai; Suarez Gonzalez, Juan; Bansal, Monika; Bansal, Sunil; Cornelis, Tom; De Wolf, Eddi A; Janssen, Xavier; Luyckx, Sten; Mucibello, Luca; Ochesanu, Silvia; Roland, Benoit; Rougny, Romain; Selvaggi, Michele; Staykova, Zlatka; Van Haevermaet, Hans; Van Mechelen, Pierre; Van Remortel, Nick; Van Spilbeeck, Alex; Blekman, Freya; Blyweert, Stijn; D'Hondt, Jorgen; Gonzalez Suarez, Rebeca; Kalogeropoulos, Alexis; Maes, Michael; Olbrechts, Annik; Van Doninck, Walter; Van Mulders, Petra; Van Onsem, Gerrit Patrick; Villella, Ilaria; Clerbaux, Barbara; De Lentdecker, Gilles; Dero, Vincent; Gay, Arnaud; Hreus, Tomas; Lonard, Alexandre; Marage, Pierre Edouard; Mohammadi, Abdollah; Reis, Thomas; Thomas, Laurent; Vander Marcken, Gil; Vander Velde, Catherine; Vanlaer, Pascal; Wang, Jian; Adler, Volker; Beernaert, Kelly; Cimmino, Anna; Costantini, Silvia; Garcia, Guillaume; Grunewald, Martin; Klein, Benjamin; Lellouch, Jrmie; Marinov, Andrey; Mccartin, Joseph; Ocampo Rios, Alberto Andres; Ryckbosch, Dirk; Strobbe, Nadja; Thyssen, Filip; Tytgat, Michael; Verwilligen, Piet; Walsh, Sinead; Yazgan, Efe; Zaganidis, Nicolas; Basegmez, Suzan; Bruno, Giacomo; Castello, Roberto; Ceard, Ludivine; Delaere, Christophe; Du Pree, Tristan; Favart, Denis; Forthomme, Laurent; Giammanco, Andrea; Hollar, Jonathan; Lemaitre, Vincent; Liao, Junhui; Militaru, Otilia; Nuttens, Claude; Pagano, Davide; Pin, Arnaud; Piotrzkowski, Krzysztof; Schul, Nicolas; Vizan Garcia, Jesus Manuel; Beliy, Nikita; Caebergs, Thierry; Daubie, Evelyne; Hammad, Gregory Habib; Alves, Gilvan; Correa Martins Junior, Marcos; De Jesus Damiao, Dilson; Martins, Thiago; Pol, Maria Elena; Henrique Gomes E Souza, Moacyr; Ald Jnior, Walter Luiz; Carvalho, Wagner; Custdio, Analu; Da Costa, Eliza Melo; De Oliveira Martins, Carley; Fonseca De Souza, Sandro; Matos Figueiredo, Diego; Mundim, Luiz; Nogima, Helio; Oguri, Vitor; Prado Da Silva, Wanda Lucia; Santoro, Alberto; Soares Jorge, Luana; Sznajder, Andre; Souza Dos Anjos, Tiago; Bernardes, Cesar Augusto; De Almeida Dias, Flavia; Tomei, Thiago; De Moraes Gregores, Eduardo; Lagana, Caio; Da Cunha Marinho, Franciole; Mercadante, Pedro G; Novaes, Sergio F; Padula, Sandra; Genchev, Vladimir; Iaydjiev, Plamen; Piperov, Stefan; Rodozov, Mircho; Stoykova, Stefka; Sultanov, Georgi; Tcholakov, Vanio; Trayanov, Rumen; Vutova, Mariana; Dimitrov, Anton; Hadjiiska, Roumyana; Kozhuharov, Venelin; Litov, Leander; Pavlov, Borislav; Petkov, Peicho; Bian, Jian-Guo; Chen, Guo-Ming; Chen, He-Sheng; Jiang, Chun-Hua; Liang, Dong; Liang, Song; Meng, Xiangwei; Tao, Junquan; Wang, Jian; Wang, Xianyou; Wang, Zheng; Xiao, Hong; Xu, Ming; Zang, Jingjing; Zhang, Zhen; Asawatangtrakuldee, Chayanit; Ban, Yong; Guo, Shuang; Guo, Yifei; Li, Wenbo; Liu, Shuai; Mao, Yajun; Qian, Si-Jin; Teng, Haiyun; Wang, Dayong; Zhang, Linlin; Zhu, Bo; Zou, Wei; Avila, Carlos; Gomez, Juan Pablo; Gomez Moreno, Bernardo; Osorio Oliveros, Andres Felipe; Sanabria, Juan Carlos; Godinovic, Nikola; Lelas, Damir; Plestina, Roko; Polic, Dunja; Puljak, Ivica; Antunovic, Zeljko; Kovac, Marko; Brigljevic, Vuko; Duric, Senka; Kadija, Kreso; Luetic, Jelena; Morovic, Srecko; Attikis, Alexandros; Galanti, Mario; Mavromanolakis, Georgios; Mousa, Jehad; Nicolaou, Charalambos; Ptochos, Fotios; Razis, Panos A; Finger, Miroslav; Finger Jr, Michael; Assran, Yasser; Elgammal, Sherif; Ellithi Kamel, Ali; Khalil, Shaaban; Mahmoud, Mohammed; Radi, Amr; Kadastik, Mario; Mntel, Mait; Raidal, Martti; Rebane, Liis; Tiko, Andres; Eerola, Paula; Fedi, Giacomo; Voutilainen, Mikko; Hrknen, Jaakko; Heikkinen, Mika Aatos; Karimki, Veikko; Kinnunen, Ritva; Kortelainen, Matti J; Lampn, Tapio; Lassila-Perini, Kati; Lehti, Sami; Lindn, Tomas; Luukka, Panja-Riina; Menp, Teppo; Peltola, Timo; Tuominen, Eija; Tuominiemi, Jorma; Tuovinen, Esa; Ungaro, Donatella; Wendland, Lauri; Banzuzi, Kukka; Karjalainen, Ahti; Korpela, Arja; Tuuva, Tuure; Besancon, Marc; Choudhury, Somnath

2012-01-01T23:59:59.000Z

113

Autonomous Units to Model Interacting Sequential and Parallel Processes  

E-Print Network (OSTI)

In this paper, we introduce the notion of a community of autonomous units as a rulebased and graph-transformational device to model processes that run interactively but independently of each other in a common environment. The main components of an autonomous unit are a set of rules, a control condition, and a goal. Every autonomous unit transforms graphs by applying its rules so that the control condition is satisfied. If the goal is reached the resulting transformation process is successful. A community contains a set of autonomous units, an initial environment specification, and an overall goal. In every transformation process of a community the autonomous units interact via their common environment. As an example, the game Ludo is modeled as a community of selfcontrolled players who interact on a common board. The emphasis of the presented approach is laid on the study of the formal semantics of a community as a whole and of each of its member units separately. In particular, a sequential as well as a parallel semantics is introduced, and communities with parallel semantics are compared with Petri nets, cellular automata, and multiagent systems.

Karsten Hlscher; Hans-Jrg Kreowski; Sabine Kuske

2009-01-01T23:59:59.000Z

114

Sandia National Laboratories Dual Laser Alignment of Solar ...  

and Weather Conditions ... Dual Laser Alignment of Solar Concentrators TECHNOLOGY READINESS LEVEL Sandia estimates this technology at approximately a ...

115

II.AdvancedTcl Advanced Tcl  

E-Print Network (OSTI)

119 P A R T II.AdvancedTcl II Advanced Tcl Part II describes advanced programming techniques that support sophisticated applications. The Tcl interfaces remain simple, so you can quickly construct pow- erful applications. Chapter 10 describes eval, which lets you create Tcl programs on the fly

Chen, Yuanzhu Peter

116

The synthesis of Nano-nano dual phase  

E-Print Network (OSTI)

The synthesis of Nano-nano dual phase ceramic composites Tomas Raming #12;Raming, Tomas Peter The synthesis of nano-nano dual phase ceramic composites Thesis University of Twente, Enschede-With ref of Scientific Research (NWO), group of Chemical Sciences (CW) #12;THE SYNTHESIS OF NANO-NANO DUAL PHASE CERAMIC

Verweij, Henk

117

On dual conservation laws in planar elasticity Shaofan Li *  

E-Print Network (OSTI)

On dual conservation laws in planar elasticity Shaofan Li * Department of Civil and Environmental form 11 December 2003; accepted 30 January 2004 Abstract Dual conservation laws of linear planar generalized symmetry transformation or Lie­Backlund transformation, a class of new dual conservation laws

Li, Shaofan

118

Conditional edge-fault-tolerant Hamiltonicity of dual-cubes  

Science Conference Proceedings (OSTI)

The dual-cube is an interconnection network for linking a large number of nodes with a low node degree. It uses low-dimensional hypercubes as building blocks and keeps the main desired properties of the hypercube. A dual-cube DC(n) has n+1 links per ... Keywords: Conditional fault-tolerant, Dual-cubes, Hamiltonian cycle, Hypercube, Interconnection network

Jheng-Cheng Chen; Chang-Hsiung Tsai

2011-02-01T23:59:59.000Z

119

Binary self-dual codes with automorphisms of order 23  

Science Conference Proceedings (OSTI)

The only example of a binary doubly-even self-dual [120,60,20] code was found in 2005 by Gaborit etal. (IEEE Trans Inform theory 51, 402---407 2005). In this work we present 25 new binary doubly-even self-dual [120,60,20] ... Keywords: 94B05, Algorithms, Automorphisms, Self-dual codes

Radinka Yorgova; Alfred Wassermann

2008-08-01T23:59:59.000Z

120

Alternating Dual-Pulse, Dual-Frequency Techniques for Range and Velocity Ambiguity Mitigation on Weather Radars  

Science Conference Proceedings (OSTI)

This paper introduces a family of alternating dual-pulse, dual-frequency (ADPDF) techniques. These are based on frequency diversity and are proposed as a means to mitigate range and velocity ambiguities on Doppler weather radars. ADPDF techniques ...

Sebastin Torres; Richard Passarelli Jr.; Alan Siggia; Pentti Karhunen

2010-09-01T23:59:59.000Z

Note: This page contains sample records for the topic "advanced sequential dual" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


121

Liquid Crystal Polymer-Based Planar Lumped Component Dual-Band Filters For Dual-Band WLAN Systems1  

E-Print Network (OSTI)

TH4A-2 Liquid Crystal Polymer-Based Planar Lumped Component Dual- Band Filters For Dual-Band WLAN River Street, Essex Junction, VT 05495 2 School of Electrical and Computer Engineering, Georgia

Swaminathan, Madhavan

122

Characteristics of the Vertical Profiles of Dual-Frequency, Dual-Polarization Radar Data in Stratiform Rain  

Science Conference Proceedings (OSTI)

Airborne dual-wavelength and dual-polarization radar data are analyzed for measurements taken in stratiform rain in the western Pacific during September 1990. The focus of the paper is on the vertical profiles of the linear depolarization ratio, ...

R. Meneghini; H. Kumagai

1994-06-01T23:59:59.000Z

123

A primal-dual interior point method for nonlinear semidefinite ...  

E-Print Network (OSTI)

Fares, Noll and Apkarian [4] applied the sequential linear SDP method to robust control problems. Recently Kanzow, Nagel, Kato and Fukushima [7] presented a.

124

CFT Duals for Extreme Black Holes  

E-Print Network (OSTI)

It is argued that the general four-dimensional extremal Kerr-Newman-AdS-dS black hole is holographically dual to a (chiral half of a) two-dimensional CFT, generalizing an argument given recently for the special case of extremal Kerr. Specifically, the asymptotic symmetries of the near-horizon region of the general extremal black hole are shown to be generated by a Virasoro algebra. Semiclassical formulae are derived for the central charge and temperature of the dual CFT as functions of the cosmological constant, Newton's constant and the black hole charges and spin. We then show, assuming the Cardy formula, that the microscopic entropy of the dual CFT precisely reproduces the macroscopic Bekenstein-Hawking area law. This CFT description becomes singular in the extreme Reissner-Nordstrom limit where the black hole has no spin. At this point a second dual CFT description is proposed in which the global part of the U(1) gauge symmetry is promoted to a Virasoro algebra. This second description is also found to re...

Hartman, Thomas; Nishioka, Tatsuma; Strominger, Andrew

2009-01-01T23:59:59.000Z

125

CFT Duals for Extreme Black Holes  

E-Print Network (OSTI)

It is argued that the general four-dimensional extremal Kerr-Newman-AdS-dS black hole is holographically dual to a (chiral half of a) two-dimensional CFT, generalizing an argument given recently for the special case of extremal Kerr. Specifically, the asymptotic symmetries of the near-horizon region of the general extremal black hole are shown to be generated by a Virasoro algebra. Semiclassical formulae are derived for the central charge and temperature of the dual CFT as functions of the cosmological constant, Newton's constant and the black hole charges and spin. We then show, assuming the Cardy formula, that the microscopic entropy of the dual CFT precisely reproduces the macroscopic Bekenstein-Hawking area law. This CFT description becomes singular in the extreme Reissner-Nordstrom limit where the black hole has no spin. At this point a second dual CFT description is proposed in which the global part of the U(1) gauge symmetry is promoted to a Virasoro algebra. This second description is also found to reproduce the area law. Various further generalizations including higher dimensions are discussed.

Thomas Hartman; Keiju Murata; Tatsuma Nishioka; Andrew Strominger

2008-11-26T23:59:59.000Z

126

Dual wakeup design for wireless sensor networks  

Science Conference Proceedings (OSTI)

Energy is often identified as the single most important resource in wireless battery-powered sensor networks. While current wakeup schemes in the literature promise to conserve energy in such networks, they apply several assumptions that may not be always ... Keywords: Cyclic block design, Dual wakeup design, Energy conservation, Lonely node, Time-tolerance sensing

Y. F. Wong; L. H. Ngoh; Winston K. G. Seah; Wai-Choong Wong

2009-01-01T23:59:59.000Z

127

Coupled dual loop absorption heat pump  

DOE Patents (OSTI)

A coupled dual loop absorption system which utilizes two separate complete loops. Each individual loop operates at three temperatures and two pressures. This low temperature loop absorber and condenser are thermally coupled to the high temperature loop evaporator, and the high temperature loop condenser and absorber are thermally coupled to the low temperature generator.

Sarkisian, Paul H. (Watertown, MA); Reimann, Robert C. (Lafayette, NY); Biermann, Wendell J. (Fayetteville, NY)

1985-01-01T23:59:59.000Z

128

Geometric skinning with approximate dual quaternion blending  

Science Conference Proceedings (OSTI)

Skinning of skeletally deformable models is extensively used for real-time animation of characters, creatures and similar objects. The standard solution, linear blend skinning, has some serious drawbacks that require artist intervention. Therefore, a ... Keywords: Skinning, dual quaternions, linear combinations, rigid transformations, transformation blending

Ladislav Kavan; Steven Collins; Ji? ra; Carol O'Sullivan

2008-10-01T23:59:59.000Z

129

DUAL FACE ALGORITHM FOR LINEAR PROGRAMMING 1 ...  

E-Print Network (OSTI)

rection, the associated line search, and operations of a dual face contraction. Section ..... (ii) An index chosen to enter the nonface index set in an expansion iteration ... of B and B, the kth row of B+ can be represented in terms of h (= 0), that is,.

130

Alternative and Advanced Fuels  

Energy.gov (U.S. Department of Energy (DOE))

There are a variety of alternative and advanced fuels available, which are used to fuel alternative and advanced vehicles. Learn more about:

131

Help - Advanced Search  

NLE Websites -- All DOE Office Websites (Extended Search)

Advanced Search The advanced search form will help you create a more specific search in the Publications database. First, specify your search criteria. You can search by author,...

132

Dual Arm Work Module Development and Appplications  

SciTech Connect

The dual arm work module (DAWM) was developed at Oak Ridge National Laboratory (ORNL) by the Robotics Technology Development Program (RTDP) as a development test bed to study issues related to dual arm manipulation, including platform cotilguration, controls, automation, operations, and tooling. The original platform was based on two Schilling Titan II manipulators mounted to a 5-degree-of- freedom (DOF) base fabricated by RedZone Robotics, Inc. The 5-DOF articulation provided a center torso rotation, linear actuation to change the separation between the arms, and arm base rotation joints to provide "elbows up," elbows down," or "elbows out" orientation. A series of tests were conducted on operations, tooling, and task space scene analysis (TSSA)-driven robotics for overhead transporter- mounted and crane hook-deployed scenarios. A concept was developed for DAWM deployment from a large remote work vehicle, but the project was redirected to support dismantlement of the Chicago Pile #5 (CP-5) reactor at Argonne National Laboratory in fiscal year (FY) 1997. Support of CP-5 required a change in focus of the dual arm technology from that of a development test bed to a system focussed for a specific end user. ORNL teamed with the Idaho National Environmental ,Engineering Laboratory, Sandia National Laboratory, and the Savannah River Technology Center to deliver a crane-deployed derivative of the DAWM, designated the dual arm work platform (DAWP). RTDP staff supported DAWP at CP-5 for one FY; Argonne staff continued operation through to dismantlement of the reactor internals. Lessons learned from this interaction were extensive. Beginning in FY 1999, dual arm development activities are again being pursued in the context of those lessons learned. This paper describes the progression of philosophy of the DAWM from initial test bed to lessons learned through interaction at CP-5 and to the present investigation of telerobotic assist of teleoperation and TSSA- driven robotics.

Noakes, M.W.

1999-04-25T23:59:59.000Z

133

Preliminary experimental investigation of a dual-band relativistic backward wave oscillator with dual beams  

Science Conference Proceedings (OSTI)

A dual-band relativistic backward wave oscillator with dual electron beams generating C-band and X-band microwaves is investigated experimentally. The frequencies, powers, and radiation patterns of the dual-band microwaves are measured. With the diode voltage of 657 kV and the total beam current of 14 kA guided by a magnetic field of about 1.7 T, the dual-band microwaves are generated with dominant frequencies of 4.58 and 8.30 GHz close to the results from the particle-in-cell simulation. The powers of the C-band and X-band microwaves are 520 and 113 MW, respectively. The effects of variations in the guiding magnetic field and diode voltage on the powers of the dual-band microwaves are presented and discussed. The radiation patterns of the dual-band microwaves from the radiating antenna are tested both corresponding to a TM{sub 01} mode and the independency of the operation processes of them is discussed.

Wang Ting; Qian Baoliang; Zhang Jiande; Zhang Xiaoping; Cao Yibing; Zhang Qiang [College of Optoelectronic Science and Engineering, National University of Defense Technology, Changsha 410073 (China)

2011-01-15T23:59:59.000Z

134

PROPERTIES OF SEQUENTIAL CHROMOSPHERIC BRIGHTENINGS AND ASSOCIATED FLARE RIBBONS  

SciTech Connect

We report on the physical properties of solar sequential chromospheric brightenings (SCBs) observed in conjunction with moderate-sized chromospheric flares with associated Coronal mass ejections. To characterize these ephemeral events, we developed automated procedures to identify and track subsections (kernels) of solar flares and associated SCBs using high-resolution H{alpha} images. Following the algorithmic identification and a statistical analysis, we compare and find the following: SCBs are distinctly different from flare kernels in their temporal characteristics of intensity, Doppler structure, duration, and location properties. We demonstrate that flare ribbons are themselves made up of subsections exhibiting differing characteristics. Flare kernels are measured to have a mean propagation speed of 0.2 km s{sup -1} and a maximum speed of 2.3 km s{sup -1} over a mean distance of 5 Multiplication-Sign 10{sup 3} km. Within the studied population of SCBs, different classes of characteristics are observed with coincident negative, positive, or both negative and positive Doppler shifts of a few km s{sup -1}. The appearance of SCBs precedes peak flare intensity by Almost-Equal-To 12 minutes and decay Almost-Equal-To 1 hr later. They are also found to propagate laterally away from flare center in clusters at 45 km s{sup -1} or 117 km s{sup -1}. Given SCBs' distinctive nature compared to flares, we suggest a different physical mechanism relating to their origin than the associated flare. We present a heuristic model of the origin of SCBs.

Kirk, Michael S.; Balasubramaniam, K. S.; Jackiewicz, Jason; McAteer, R. T. James [Department of Astronomy, New Mexico State University, P.O. Box 30001, MSC 4500, Las Cruces, NM 88003-8001 (United States); Milligan, Ryan O., E-mail: mskirk@nmsu.edu [Astrophysics Research Centre, School of Mathematics and Physics, Queen's University Belfast, University Road Belfast, BT7 1NN (United Kingdom)

2012-05-10T23:59:59.000Z

135

UC Berkeley computer science Subject: Introducing sequential behavior in Fleet  

E-Print Network (OSTI)

This memo started as a presentation of one idea for introducing sequentiality into an instruction issue mechanism for Fleet. The idea was the concept of a logical clock. Even though the idea was far from polished, I decided it was valuable to record the idea and possibly sharpen it during the writing process. As I was writing the memo, I was following my train of thought, got stuck a number of times, and ended up wring a memo that describes a whole collection of unpolished ideas. I still believe the exercise was worth undertaking, not only for the sheer benefits of what is recorded in this memo but for the benefit of at least five more memos that got started while I was writing this memo. BASE MODEL: A POOL OF CONCURRENT INSTRUCTIONS Figure 1 shows an abstract view of Fleet processor architecture. Note that the core elements of Fleet remain in the picture: Ships are connected via a switch fabric, where each ship serves as both a source of data and a destination for data. The switch fabric enables data transfer between ships. That is, each move instruction that the instruction issue unit releases into the switch fabric transfers data between a source ship and a destination ship. Note that execution of an instruction is limited to the data transfer itself. Any data transformation that may happen inside a ship is a part of operation of the ship. As a result of such an operation, a new data item may be available at the ships source port. One can say that data transformation takes place as a side effect of data movement. _____________________________________________________________________________ This document is a product of a collaboration between Sun Microsystems and the University of California at Berkeley. The ideas contained herein are freely available for any academic purpose.

Igor Benko

2005-01-01T23:59:59.000Z

136

Economizer Applications in Dual-Duct Air-Handling Units  

E-Print Network (OSTI)

This paper provides analytical tools and engineering methods to evaluate the feasibility of the economizer for dual-duct air-handling units. The results show that the economizer decreases cooling energy consumption without heating energy penalties for dual-fan, dual-duct air-handling units. The economizer has significant heating energy penalties for single-fan, dual-duct air-handling units. The penalties are higher than the cooling energy savings when the cold airflow is less than the hot airflow. Detailed engineering analyses are required to evaluate the feasibility of the economizer for single-fan, dual-duct systems.

Joo, I.; Liu, M.

2002-01-01T23:59:59.000Z

137

An Inverse Method for Tracking Ice Motion in the Marginal Ice Zone Using Sequential Satellite Images  

Science Conference Proceedings (OSTI)

A new method for tracking ice motion and estimating ocean surface currents from sequential satellite images is presented. It is particularly suited for the marginal ice zone. A simple ice advection model, driven by wind and surface currents, is ...

Mark Buehner; Keith R. Thompson; Ingrid Peterson

1997-12-01T23:59:59.000Z

138

Design as you see FIT: system-level soft error analysis of sequential circuits  

Science Conference Proceedings (OSTI)

Soft errors in combinational and sequential elements of digital circuits are an increasing concern as a result of technology scaling. Several techniques for gate and latch hardening have been proposed to synthesize circuits that are tolerant to soft ...

Daniel Holcomb; Wenchao Li; Sanjit A. Seshia

2009-04-01T23:59:59.000Z

139

A Sequential Variational Algorithm for Data Assimilation in Oceanography and Meteorology  

Science Conference Proceedings (OSTI)

This study theoretically establishes a sequential variational (SVAR) method for the data assimilation in oceanography and meteorology defined on the model space. Requiring a significantly smaller amount of computer memory, theoretically SVAR ...

Srdjan Dobricic

2009-01-01T23:59:59.000Z

140

Rational plunging and the option value of sequential investment : the case of petroleum exploration  

E-Print Network (OSTI)

Any investor in assets that can be exploited sequentially faces a tradeoff between diversification and concentration. Loading a portfolio with correlated assets has the potential to inflate variance, but also creates ...

Smith, James L.

2006-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "advanced sequential dual" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


141

Extracting Multiyear Surface Currents from Sequential Thermal Imagery Using the Maximum Cross-Correlation Technique  

Science Conference Proceedings (OSTI)

Ocean surface circulation can be estimated by automated tracking of thermal infrared features in pairs of sequential satellite imagery. A 7-yr time series of velocity, extracted from thermal imagery of the East Australian Current using the ...

Melissa M. Bowen; William J. Emery; John L. Wilkin; Paul C. Tildesley; Ian J. Barton; Rebecca Knewtson

2002-10-01T23:59:59.000Z

142

Computer-Controlled Automated Rain Sampler (CCARS) for Rainfall Measurement and Sequential Sampling  

Science Conference Proceedings (OSTI)

The Computer-Controlled Automated Rain Sampler (CCARS) is a combination rain gage and sequential sampler for precipitation chemistry measurements. The primary objectives of the design are low cost, versatility of operational mode, and remote ...

Stan D. Tomich; M. Terry Dana

1990-08-01T23:59:59.000Z

143

Concurrencer: a tool for retrofitting concurrency into sequential Java applications via concurrent libraries  

E-Print Network (OSTI)

Parallelizing existing sequential programs to run efficiently on multicores is hard. The Java 5 package java.util.concurrent (j.u.c.) supports writing concurrent programs. To use this package, programmers still need to ...

Dig, Danny

144

An Application of Sequential Variational Method without Tangent Linear and Adjoint Model Integrations  

Science Conference Proceedings (OSTI)

The sequential variational (SVAR) method minimizes the weakly constrained four-dimensional cost function by splitting it into a set of smaller cost functions. This study shows how it is possible to apply SVAR in practice by reducing the ...

Srdjan Dobricic

2013-01-01T23:59:59.000Z

145

Analysis of Parallel versus Sequential Splittings for Time-Stepping Physical Parameterizations  

Science Conference Proceedings (OSTI)

Various numerical issues concerning different approaches to the time stepping of physical parameterizations in numerical weather prediction (NWP) and climate models are examined. Parallel-split and sequential-split methods are explained and ...

Mark Dubal; Nigel Wood; Andrew Staniforth

2004-01-01T23:59:59.000Z

146

Advanced Materials in MML  

Science Conference Proceedings (OSTI)

... Advanced Materials Characterization. Fusion Wall Development Research by Neutron Depth Profiling. < Previous 1 2 3 Next . ...

2012-06-12T23:59:59.000Z

147

Dual Axis Radiographic Hydrodynamic Test Facility  

NLE Websites -- All DOE Office Websites (Extended Search)

DARHT Facility: A critical component of stockpile stewardship DARHT Facility: A critical component of stockpile stewardship A new research frontier awaits! Our door is open and we thrive on mutually beneficial partnerships, collaborations that drive innovations and new technologies. April 12, 2012 Dominic Tafoya and Dave Honaberger prepare a refurbished DARHT (Dual Axis Radiographic Hydrotest Facility) 2nd axis accelerator cell for magnetic axis alignment measurements. Contact Group Leader Terry Priestley (505) 665-1330 Email Deputy Group Leader Tim Ferris (505) 665-2179 Email Hydrotests are critical in assessing nuclear weapons in nation's stockpile Dual Axis Radiographic Hydrodynamic Test facility 4:17 How DARHT Works The weapons programs at Los Alamos have one principal mission: ensure the safety, security, and effectiveness of nuclear weapons in our nation's

148

Black branes dual to striped phases  

E-Print Network (OSTI)

We construct inhomogeneous charged black branes in AdS, holographically dual to a phase at finite chemical potential with spontaneously broken translation invariance in one direction. These are obtained numerically, solving PDEs for the fully backreacted system. Fixing the periodicity scale, we find a second order phase transition to the inhomogeneous phase. We comment on the properties of the state emerging at low temperatures. For some models we demonstrate the existence of a branch of striped solutions but no continuous phase transition.

Benjamin Withers

2013-03-30T23:59:59.000Z

149

Fabrication of dual porosity electrode structure  

DOE Patents (OSTI)

A substantially entirely fibrous ceramic is described which may have dual porosity of both micro and macro pores. Total porosity may be 60-75% by volume. A method of spraying a slurry perpendicularly to an ambient stream of air is disclosed along with a method of removing binders without altering the fiber morphology. Adding fine ceramic particulates to the green ceramic fibers enhances the sintering characteristics of the fibers. 3 figures.

Smith, J.L.; Kucera, E.H.

1991-02-12T23:59:59.000Z

150

Twisted covariant noncommutative self-dual gravity  

Science Conference Proceedings (OSTI)

A twisted covariant formulation of noncommutative self-dual gravity is presented. The formulation for constructing twisted noncommutative Yang-Mills theories is used. It is shown that the noncommutative torsion is solved at any order of the {theta} expansion in terms of the tetrad and some extra fields of the theory. In the process the first order expansion in {theta} for the Plebanski action is explicitly obtained.

Estrada-Jimenez, S.; Garcia-Compean, H.; Obregon, O.; Ramirez, C. [Centro de Estudios en Fisica y Matematicas Basicas y Aplicadas, Universidad Autonoma de Chiapas, Calle 4 Oriente Norte 1428, Tuxtla Gutierrez, Chiapas (Mexico); Departamento de Fisica, Centro de Investigacion y de Estudios Avanzados del IPN, P.O. Box 14-740, 07000 Mexico D.F. (Mexico); Centro de Investigacion y de Estudios Avanzados del IPN, Unidad Monterrey, PIIT, Via del Conocimiento 201, Autopista nueva al Aeropuerto km 9.5, 66600, Apodaca Nuevo Leon (Mexico); Instituto de Fisica de la Universidad de Guanajuato, P.O. Box E-143, 37150, Leon Gto. (Mexico); Facultad de Ciencias Fisico Matematicas, Universidad Autonoma de Puebla, P.O. Box 1364, 72000, Puebla (Mexico)

2008-12-15T23:59:59.000Z

151

Fabrication of dual porosity electrode structure  

DOE Patents (OSTI)

A substantially entirely fibrous ceramic which may have dual porosity of both micro and macro pores. Total porosity may be 60-75% by volume. A method of spraying a slurry perpendicularly to an ambient stream of air is disclosed along with a method of removing binders without altering the fiber morphology. Adding fine ceramic particulates to the green ceramic fibers enhances the sintering characteristics of the fibers.

Smith, James L. (Lemont, IL); Kucera, Eugenia H. (Downers Grove, IL)

1991-01-01T23:59:59.000Z

152

Hadron physics as Seiberg dual of QCD  

SciTech Connect

We try to identify the light hadron world as the magnetic picture of QCD. We take both phenomenological and theoretical approaches to this hypothesis, and find that the interpretation seems to show interesting consistencies. In particular, one can identify the {rho} and {omega} mesons as the magnetic gauge bosons, and the Higgs mechanism for them provides a dual picture of the color confinement{sup 1}.

Kitano, Ryuichiro [Department of Physics, Tohoku University, Sendai 980-8578 (Japan)

2012-07-27T23:59:59.000Z

153

Inorganic dual-layer microporous supported membranes  

SciTech Connect

The present invention provides for a dual-layer inorganic microporous membrane capable of molecular sieving, and methods for production of the membranes. The inorganic microporous supported membrane includes a porous substrate which supports a first inorganic porous membrane having an average pore size of less than about 25 .ANG. and a second inorganic porous membrane coating the first inorganic membrane having an average pore size of less than about 6 .ANG.. The dual-layered membrane is produced by contacting the porous substrate with a surfactant-template polymeric sol, resulting in a surfactant sol coated membrane support. The surfactant sol coated membrane support is dried, producing a surfactant-templated polymer-coated substrate which is calcined to produce an intermediate layer surfactant-templated membrane. The intermediate layer surfactant-templated membrane is then contacted with a second polymeric sol producing a polymeric sol coated substrate which is dried producing an inorganic polymeric coated substrate. The inorganic polymeric coated substrate is then calcined producing an inorganic dual-layered microporous supported membrane in accordance with the present invention.

Brinker, C. Jeffrey (14 Eagle Nest Dr. NE., Albuquerque, NM 87122); Tsai, Chung-Yi (6 Mount Vernon Dr., Apt. C, Vernon, CT 06066); Lu, Yungfeng (1055 N. Capital Ave., #20, San Jose, CA 95133)

2003-03-25T23:59:59.000Z

154

Argonne CNM News: A better etching technique: sequential infiltration  

NLE Websites -- All DOE Office Websites (Extended Search)

A Better Etching Technique Is Invented A Better Etching Technique Is Invented Mark Holt (Argonne Center for Nanoscale Materials) examines a sample in the Hard X-Ray Nanoprobe Deep canyons can be etched into materials at the nanoscale with a new SIS-based lithography technique Nanoscientists at Argonne's Center for Nanoscale Materials and Energy Systems Division have discovered a new way to transfer patterns onto different materials, an innovation that combines new tricks with an old technology. One of the biggest recent questions facing materials science has involved the development of better techniques for high-resolution lithographies such as electron-beam (e-beam) lithography. E-beam lithography is used to manufacture the tiniest of structures, including microelectronics and advanced sensors; beams of electrons are part of a

155

New MDS or near-MDS self-dual codes  

E-Print Network (OSTI)

AbstractWe construct new MDS or near-MDS self-dual codes over large finite fields. In particular we show that there exists a Euclidean self-dual MDS code of length n = q over GF (q) whenever q = 2 m (m ? 2) using a Reed-Solomon (RS) code and its extension. It turns out that this MDS self-dual code is an extended duadic code. We construct Euclidean self-dual near-MDS codes of length n = q ? 1 over GF (q) from RS codes when q ? 1 (mod 4) and q ? 113. We also construct many new MDS self-dual codes over GF (p) of length 16 for primes 29 ? p ? 113. Finally we construct Euclidean/Hermitian self-dual MDS codes of lengths up to 14 over GF (q 2) where q = 19, 23, 25, 27, 29.

T. Aaron Gulliver; Yoonjin Lee

2008-01-01T23:59:59.000Z

156

Nuclear fusion advances  

Science Conference Proceedings (OSTI)

The last decade has seen advances in the shaping and confinement of plasmas, and in approaches to noninductive current drive. Here, the author presents an overview of nuclear fusion advances between 1983-93 examining: fusion milestones; plasma shaping; ...

W. Sweet

1994-02-01T23:59:59.000Z

157

AdvAnced  

NLE Websites -- All DOE Office Websites (Extended Search)

AdvAnced test reActor At the InL advanced Unlike large, commercial power reactors, ATR is a low- temperature, low-pressure reactor. A nuclear reactor is basically an elaborate tool...

158

Construction of MDS self-dual codes over Galois rings  

Science Conference Proceedings (OSTI)

The purpose of this paper is to construct nontrivial MDS self-dual codes over Galois rings. We consider a building-up construction of self-dual codes over Galois rings as a GF(q)-analogue of (Kim and Lee, J Combin Theory ser A, 105:79---95). We ... Keywords: 13H99, 94B05, Galois ring, MDS code, Self-dual code

Jon-Lark Kim; Yoonjin Lee

2007-11-01T23:59:59.000Z

159

ADVANCED DATA SECURITY  

Science Conference Proceedings (OSTI)

ADVANCED DATA SECURITY. NVLAP Lab Code: 200968-0. Address and Contact Information: 1933 O'Toole Avenue San ...

2013-11-08T23:59:59.000Z

160

Fatigue of Advanced Materials  

Science Conference Proceedings (OSTI)

Oct 19, 2011... isolate the internal components from the external environment while ... overall thermal efficiency of advanced internal combustion engines...

Note: This page contains sample records for the topic "advanced sequential dual" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


161

Advancement of Electrochromic Windows  

E-Print Network (OSTI)

advanced spectrally selective low-e double-pane windows and the same type of daylighting control system

2006-01-01T23:59:59.000Z

162

Advanced High Frequency Devices  

Science Conference Proceedings (OSTI)

... External agencies, including the Defense Advanced Research Projects Agency (DARPA) and the Office of Naval Research (ONR), have ...

2010-10-05T23:59:59.000Z

163

Supporting Advanced Communications Networks  

Science Conference Proceedings (OSTI)

... it will rely on revolutionary advances in network architecture. ... telemedicine), sensor and control networks (eg, Smart Grid, environmental monitoring ...

2012-02-13T23:59:59.000Z

164

Strongly Polynomial Primal-Dual Algorithms for Concave Cost ...  

E-Print Network (OSTI)

Feb 13, 2012 ... This technique yields a strongly polynomial primal-dual algorithm for a concave cost problem whenever such an algorithm exists for the...

165

Approval Process for Dual Compensation Waivers for Reemployed...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

DIRECTOR OFFICE 0 UMAN CAPITAL MANAGEMENT SUBJECT: POLICY MEMORANDUM 11: APPROVAL PROCESS FOR DUAL COMPENSATION WAIVERS FOR REEMPLOYED ANNUITANTS Section 1122 of the National...

166

Primal-dual methods for solving infinite-dimensional games  

E-Print Network (OSTI)

(1958), 171-176. http://projecteuclid.org/euclid.pjm/1103040253. [4] Nesterov, Yurii. Primal-dual subgradient methods for convex problems. In: Mathematical.

167

DARHT: Dual-Axis Radiographic Hydrodynamic Test Facility  

NLE Websites -- All DOE Office Websites (Extended Search)

Radiographic Hydrodynamic Test Facility DARHT: Dual-Axis Radiographic Hydrodynamic Test Facility DARHT, supports a critical component of LANL's primary mission: to ensure...

168

RATE ANALYSIS OF INEXACT DUAL FIRST ORDER METHODS ...  

E-Print Network (OSTI)

The dual problem is solved by inexact first order methods based on ..... only approximately and shows that algorithm (IDG) does not accumulate errors. However...

169

Session: CSP Advanced Systems -- Advanced Overview (Presentation)  

DOE Green Energy (OSTI)

The project description is: (1) it supports crosscutting activities, e.g. advanced optical materials, that aren't tied to a single CSP technology and (2) it supports the 'incubation' of new concepts in preliminary stages of investigation.

Mehos, M.

2008-04-01T23:59:59.000Z

170

Dual stage active magnetic regenerator and method  

DOE Patents (OSTI)

A dual stage active magnetic regenerator refrigerator as well as method using the Joule-Brayton thermodynamic cycle includes a high temperature stage refrigerant comprising DyAl{sub 2} or (Dy{sub 1{minus}x}Er{sub x})Al{sub 2} where x is selected to be greater than 0 and less than about 0.3 in combination with a low temperature stage comprising (Dy{sub 1{minus}x}Er{sub x})Al{sub 2} where x is selected to be greater than about 0.5 and less than 1 to provide significantly improved refrigeration efficiency in the liquefaction of gaseous hydrogen. 17 figs.

Pecharsky, V.K.; Gschneidner, K.A. Jr.

1999-03-30T23:59:59.000Z

171

Dual stage active magnetic regenerator and method  

DOE Patents (OSTI)

A dual stage active magnetic regenerator refrigerator as well as method using the Joule-Brayton thermodynamic cycle includes a high temperature stage refrigerant comprising DyAl.sub.2 or (Dy.sub.1-x Er.sub.x)Al.sub.2 where x is selected to be greater than 0 and less than about 0.3 in combination with a low temperature stage comprising (Dy.sub.1-x Er.sub.x)Al.sub.2 where x is selected to be greater than about 0.5 and less than 1 to provide significantly improved refrigeration efficiency in the liquefaction of gaseous hydrogen.

Pecharsky, Vitalij K. (Ames, IA); Gschneidner, Jr., Karl A. (Ames, IA)

1999-03-30T23:59:59.000Z

172

Advanced Manufacturing Office: Better Plants  

NLE Websites -- All DOE Office Websites (Extended Search)

Better Plants on Twitter Bookmark Advanced Manufacturing Office: Better Plants on Google Bookmark Advanced Manufacturing Office: Better Plants on Delicious Rank Advanced...

173

Advanced Manufacturing Office: Pump Systems  

NLE Websites -- All DOE Office Websites (Extended Search)

Pump Systems on Twitter Bookmark Advanced Manufacturing Office: Pump Systems on Google Bookmark Advanced Manufacturing Office: Pump Systems on Delicious Rank Advanced...

174

Russian collaborations on lasers and advanced optics  

SciTech Connect

This is the final report of a one-year, Laboratory Directed Research and Development (LDRD) project at the Los Alamos National Laboratory. There are several technological areas where the Russians appear to be well ahead of the West. Russian work in lasers and advanced optics, high power nonlinear optics, and optical phase conjugation in particular, are some of these areas. The objective of this project is to establish collaboration with key Russian scientists in this area to analytically and experimentally validate the technologies and identify potential applications. This technology has the potential to solve very important military, civil, and commercial problems. The emphasis of this project is on civil and commercial applications, but the technologies have dual-use applications.

Munroe, J.; Cooper, D.; Koym, V.; Salesky, E.

1996-09-01T23:59:59.000Z

175

Dual alkali approaches for the capture and separation of CO{sub 2}  

SciTech Connect

The Solvay process utilizes two alkalis in sequential order to convert CO{sub 2} to sodium carbonate for commercial use. The ability to transform CO{sub 2} into sodium carbonate cost-effectively would be a breakthrough in CO{sub 2} sequestration by providing benign long-term storage of CO{sub 2}. However, the Solvay process was not designed for CO{sub 2} sequestration and is not practical for use in the sequestration of CO{sub 2} from fossil fuel power plants. This paper investigates methods to modify the process in order to make it effective for the control of power plant CO{sub 2} emissions. The new modified process, called the Dual Alkali Approach, attempts to replace either or both bases, ammonia and lime, in the Solvay process with other compounds to make CO{sub 2} capture and separation efficient. Ammonia was replaced with different amines in aqueous solutions of salts and it was found that bicarbonate precipitation did occur. A method to regenerate the amine in the second step has not been implemented. However, the second step in Solvay Process has been implemented without using lime, namely, ammonia has been regenerated from an ammonium chloride solution using activated carbon. The HCl adsorbed in the activated carbon was removed by water to regenerate the activated carbon.

Huang, H.P.; Shi, Y.; Li, W.; Chang, S.G.

2000-04-04T23:59:59.000Z

176

The Gravity Dual of the Ising Model  

E-Print Network (OSTI)

We evaluate the partition function of three dimensional theories of gravity in the quantum regime, where the AdS radius is Planck scale and the central charge is of order one. The contribution from the AdS vacuum sector can - with certain assumptions - be computed and equals the vacuum character of a minimal model CFT. The torus partition function is given by a sum over geometries which is finite and computable. For generic values of Newton's constant G and the AdS radius L the result has no Hilbert space interpretation, but in certain cases it agrees with the partition function of a known CFT. For example, the partition function of pure Einstein gravity with G=3L equals that of the Ising model, providing evidence that these theories are dual. We also present somewhat weaker evidence that the 3-state and tricritical Potts models are dual to pure higher spin theories of gravity based on SL(3) and E_6, respectively.

Alejandra Castro; Matthias R. Gaberdiel; Thomas Hartman; Alexander Maloney; Roberto Volpato

2011-11-08T23:59:59.000Z

177

The Gravity Dual of the Ising Model  

E-Print Network (OSTI)

We evaluate the partition function of three dimensional theories of gravity in the quantum regime, where the AdS radius is Planck scale and the central charge is of order one. The contribution from the AdS vacuum sector can - with certain assumptions - be computed and equals the vacuum character of a minimal model CFT. The torus partition function is given by a sum over geometries which is finite and computable. For generic values of Newton's constant G and the AdS radius L the result has no Hilbert space interpretation, but in certain cases it agrees with the partition function of a known CFT. For example, the partition function of pure Einstein gravity with G=3L equals that of the Ising model, providing evidence that these theories are dual. We also present somewhat weaker evidence that the 3-state and tricritical Potts models are dual to pure higher spin theories of gravity based on SL(3) and E_6, respectively.

Castro, Alejandra; Hartman, Thomas; Maloney, Alexander; Volpato, Roberto

2011-01-01T23:59:59.000Z

178

An Underwater Sensor Network with Dual Communications, Sensing, and  

E-Print Network (OSTI)

An Underwater Sensor Network with Dual Communications, Sensing, and Mobility Carrick Detweiller an underwater sensor network with dual communication and sup- port for sensing and mobility. The nodes developed. We describe the hardware details of the underwater sensor node and the communication

Farritor, Shane

179

Virtual monochromatic imaging in dual-source dual-energy CT: Radiation dose and image quality  

Science Conference Proceedings (OSTI)

Purpose: To evaluate the image quality of virtual monochromatic images synthesized from dual-source dual-energy computed tomography (CT) in comparison with conventional polychromatic single-energy CT for the same radiation dose. Methods: In dual-energy CT, besides the material-specific information, one may also synthesize monochromatic images at different energies, which can be used for routine diagnosis similar to conventional polychromatic single-energy images. In this work, the authors assessed whether virtual monochromatic images generated from dual-source CT scanners had an image quality similar to that of polychromatic single-energy images for the same radiation dose. First, the authors provided a theoretical analysis of the optimal monochromatic energy for either the minimum noise level or the highest iodine contrast to noise ratio (CNR) for a given patient size and dose partitioning between the low- and high-energy scans. Second, the authors performed an experimental study on a dual-source CT scanner to evaluate the noise and iodine CNR in monochromatic images. A thoracic phantom with three sizes of attenuating rings was used to represent four adult sizes. For each phantom size, three dose partitionings between the low-energy (80 kV) and the high-energy (140 kV) scans were used in the dual-energy scan. Monochromatic images at eight energies (40 to 110 keV) were generated for each scan. Phantoms were also scanned at each of the four polychromatic single energy (80, 100, 120, and 140 kV) with the same radiation dose. Results: The optimal virtual monochromatic energy depends on several factors: phantom size, partitioning of the radiation dose between low- and high-energy scans, and the image quality metrics to be optimized. With the increase of phantom size, the optimal monochromatic energy increased. With the increased percentage of radiation dose on the low energy scan, the optimal monochromatic energy decreased. When maximizing the iodine CNR in monochromatic images, the optimal energy was lower than that when minimizing noise level. When the total radiation dose was equally distributed between low and high energy in dual-energy scans, for minimum noise, the optimal energies were 68, 71, 74, and 77 keV for small, medium, large, and extra-large (xlarge) phantoms, respectively; for maximum iodine CNR, the optimal energies were 66, 68, 70, 72 keV. With the optimal monochromatic energy, the noise level was similar to and the CNR was better than that in a single-energy scan at 120 kV for the same radiation dose. Compared to an 80 kV scan, however, the iodine CNR in monochromatic images was lower for the small, medium, and large phantoms. Conclusions: In dual-source dual-energy CT, optimal virtual monochromatic energy depends on patient size, dose partitioning, and the image quality metric optimized. With the optimal monochromatic energy, the noise level was similar to and the iodine CNR was better than that in 120 kV images for the same radiation dose. Compared to single-energy 80 kV images, the iodine CNR in virtual monochromatic images was lower for small to large phantom sizes.

Yu Lifeng; Christner, Jodie A.; Leng Shuai; Wang Jia; Fletcher, Joel G.; McCollough, Cynthia H. [Department of Radiology, Mayo Clinic, Rochester, Minnesota 55905 (United States)

2011-12-15T23:59:59.000Z

180

Metabolic complementarity and genomics of the dual bacterial symbiosis of sharpshooters  

E-Print Network (OSTI)

Metabolic Complementarity and Genomics of the Dual BacterialMetabolic complementarity and genomics of the dual bacterialthe other. ) Comparative genomics. The predicted proteomes

2006-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "advanced sequential dual" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


181

Dual Rater Competency Assessment FAQ | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Dual Rater Competency Assessment FAQ Dual Rater Competency Assessment FAQ Dual Rater Competency Assessment FAQ 1. What is the purpose of the dual rater assessments? The purpose of the dual rater competency assessment is to provide a clearer picture of the individual's developmental needs by combining self-assessment and supervisory input. Together, these two viewpoints provide a more informed assessment of individual strengths and developmental needs. Managers/supervisors and employees will be able to use competency assessment results to identify and address critical skills gaps through targeted training and development. From an organizational perspective, the competency assessment process enables organizations to assess workforce competencies and helps ensure its current workforce has the right knowledge and skills to accomplish the

182

York Electric Cooperative - Dual Fuel Heat Pump Rebate Program | Department  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

York Electric Cooperative - Dual Fuel Heat Pump Rebate Program York Electric Cooperative - Dual Fuel Heat Pump Rebate Program York Electric Cooperative - Dual Fuel Heat Pump Rebate Program < Back Eligibility Commercial Fed. Government Industrial Local Government Nonprofit Residential State Government Savings Category Heating & Cooling Commercial Heating & Cooling Heat Pumps Maximum Rebate 2 systems per household Program Info State South Carolina Program Type Utility Rebate Program Rebate Amount Dual Fuel Heat Pumps: $400/system Provider York Electric Cooperative, Inc York Electric Cooperative, Inc. (YEC) offers a $400 rebate to members who install a dual fuel heat pump in homes or businesses. The rebates are for primary residence and/or commercial and industrial locations. The incentive is for the property owner only, meaning that renters/tenants are not

183

On Parallelizing Dual Decomposition in Stochastic Integer Programming |  

NLE Websites -- All DOE Office Websites (Extended Search)

On Parallelizing Dual Decomposition in Stochastic Integer Programming On Parallelizing Dual Decomposition in Stochastic Integer Programming Title On Parallelizing Dual Decomposition in Stochastic Integer Programming Publication Type Journal Article Year of Publication 2013 Authors Lubin, M, Martin, K, Petra, CG, Sandikci, B Journal Operations Research Letters Volume 41 Start Page 252-258 Issue 3 Date Published 05/2013 Other Numbers ANL/MCS-P3037-0912 Abstract For stochastic mixed-integer programs, we revisit the dual decomposition algorithm of Care and Schultz from a computational perspective with the aim of its parallelization. We address an important bottleneck of parallel execution by identifying a formulation that permits the parallel solution of the master program by using structure-exploiting interior-point solvers. Our results demonstrate the potential for parallel speedup and the importance of regularization (stabilization) in the dual optimization. Load imbalance is identified as a remaining barrier to parallel scalability.

184

Advanced Manufacturing Office: Technical Assistance  

NLE Websites -- All DOE Office Websites (Extended Search)

Assistance on Twitter Bookmark Advanced Manufacturing Office: Technical Assistance on Google Bookmark Advanced Manufacturing Office: Technical Assistance on Delicious Rank...

185

Advanced Manufacturing Office: Financial Opportunities  

NLE Websites -- All DOE Office Websites (Extended Search)

on Twitter Bookmark Advanced Manufacturing Office: Financial Opportunities on Google Bookmark Advanced Manufacturing Office: Financial Opportunities on Delicious Rank...

186

Accurate sequential self-localization of sensor nodes in closed-form  

Science Conference Proceedings (OSTI)

This paper addresses the problem of obtaining an efficient estimator for sensor node self-localization using time of arrival (TOA) measurements. A sequential scheme is proposed that consists of closed-form single node localization and sensor position ... Keywords: Localization, Sensor position errors, Time of arrival (TOA)

M. Sun; L. Yang; K. C. Ho

2012-12-01T23:59:59.000Z

187

A sequential minimal optimization algorithm for the all-distances support vector machine  

Science Conference Proceedings (OSTI)

The All-Distances SVM is a single-objective light extension of the binary -SVM for multi-category classification that is competitive against multi-objective SVMs, such as One-against-the-Rest SVMs and One-against-One SVMs. Although the model takes ... Keywords: kernel machines, multi-category classification, sequential minimal optimization, support vector machines

Diego Candel; Ricardo anculef; Carlos Concha; Hctor Allende

2010-11-01T23:59:59.000Z

188

Deadlock Avoidance for Sequential Resource Allocation Systems: Hard and Easy Cases  

E-Print Network (OSTI)

1 Deadlock Avoidance for Sequential Resource Allocation Systems: Hard and Easy Cases Mark Lawley is computationally hard, and numerous sub-optimal deadlock avoidance solutions have been proposed for this class and investigating the boundary between the hard and easy cases. We discuss several special structures that lead

Reveliotis, Spiridon "Spyros"

189

A Hybrid Architecture for Situated Learning of Reactive Sequential Decision Making  

Science Conference Proceedings (OSTI)

In developing autonomous agents, one usually emphasizes only (situated) procedural knowledge, ignoring more explicit declarative knowledge. On the other hand, in developing symbolic reasoning models, one usually emphasizes only declarative knowledge, ignoring ... Keywords: cognitive modeling, hybrid models, neural networks, reinforcement learning, sequential decision making

Ron Sun; Todd Peterson; Edward Merrill

1999-07-01T23:59:59.000Z

190

Semi-RAID: A reliable energy-aware RAID data layout for sequential data access  

Science Conference Proceedings (OSTI)

In this paper, we propose an alternative RAID data layout, Semi-RAID (S-RAID), for the kind of application that exhibits a sequential data access pattern. The data layout of S-RAID uses a grouping strategy that makes only part of the whole array active ...

Li Xiao; Tan Yu-An; Sun Zhizhuo

2011-05-01T23:59:59.000Z

191

Sequential parameter estimation of time-varying non-Gaussian autoregressive processes  

Science Conference Proceedings (OSTI)

Parameter estimation of time-varying non-Gaussian autoregressive processes can be a highly nonlinear problem. The problem gets even more difficult if the functional form of the time variation of the process parameters is unknown. In this paper, we address ... Keywords: Gaussian mixtures, forgetting factors, particle filtering, sequential importance sampling

Petar M. Djuri?; Jayesh H. Kotecha; Fabien Esteve; Etienne Perret

2002-01-01T23:59:59.000Z

192

Effective temporal data classification by integrating sequential pattern mining and probabilistic induction  

Science Conference Proceedings (OSTI)

Data classification is an important topic in the field of data mining due to its wide applications. A number of related methods have been proposed based on the well-known learning models such as decision tree or neural network. Although data classification ... Keywords: Classification, Data mining, Scoring method, Sequential pattern, Temporal data

Vincent S. Tseng; Chao-Hui Lee

2009-07-01T23:59:59.000Z

193

An agent-based stochastic ruler approach for a stochastic knapsack problem with sequential competition  

Science Conference Proceedings (OSTI)

We examine a situation in which a decision-maker executes a sequence of resource allocation decisions over time, but the availability of the indivisible resources at future epochs is uncertain due to actions of competitors. We cast this problem as a ... Keywords: Agent-based simulation, Beam search, Discrete stochastic optimization, Knapsack problem, Sequential allocation, Stochastic ruler

Matthew R. Gibson; Jeffrey W. Ohlmann; Michael J. Fry

2010-03-01T23:59:59.000Z

194

A Sequential Element Rejection and Admission (SERA) method for compliant mechanisms design  

Science Conference Proceedings (OSTI)

A Sequential Element Rejection and Admission (SERA) method to design compliant mechanisms with topology optimization techniques is presented in this work. This procedure allows material to flow between two different material models: `real' and `virtual'. ... Keywords: Compliant mechanisms, Parameter study, SERA method, Topology optimization

Cristina Alonso, Osvaldo M. Querin, Rubn Ansola

2013-06-01T23:59:59.000Z

195

A Sequential Game Perspective and Optimization of the Smart Grid with Distributed Data Centers  

E-Print Network (OSTI)

A Sequential Game Perspective and Optimization of the Smart Grid with Distributed Data Centers to their enormous energy consumption, data centers are expected to have major impact on the electric grid]. Data centers are expected to have a major impact on the electric grid by significantly increasing

Pedram, Massoud

196

Advanced Concepts Breakout Group  

NLE Websites -- All DOE Office Websites (Extended Search)

Workshop Workshop Advanced Concepts Working Group Facilitator: John J. Petrovic Scribe: Sherry Marin Advanced Storage Techniques/ Approaches in Priority Order 1. Crystalline Nanoporous Materials (15) 2. Polymer Microspheres (12) Self-Assembled Nanocomposites (12) 3. Advanced Hydrides (11) Metals - Organic (11) 4. BN Nanotubes (5) Hydrogenated Amorphous Carbon (5) 5. Mesoporous materials (4) Bulk Amorphous Materials (BAMs) (4) 6. Iron Hydrolysis (3) 7. Nanosize powders (2) 8. Metallic Hydrogen (1) Hydride Alcoholysis (1) Overarching R&D Questions for All Advanced Materials * Maximum storage capacity - theoretical model * Energy balance / life cycle analysis * Hydrogen absorption / desorption kinetics * Preliminary cost analysis - potential for low cost, high

197

Institute for Advanced Studies  

NLE Websites -- All DOE Office Websites (Extended Search)

Institute for Advanced Studies Institute for Advanced Studies Institute for Advanced Studies NMC leverages the strengths of three research universities to build joint programs, develop strategic partnerships, provide common organization and facilities. Contact Leader TBD LANL Program Administrator Pam Hundley (505) 663-5453 Email Building regional partnerships in education, leveraging strengths of three research universities The Institute for Advanced Studies (IAS) works with the three New Mexico research universities (University of New Mexico, New Mexico Tech, and New Mexico State University) to develop research and educational collaborations and partnerships. To facilitate interactions between the universities and LANL, the three New Mexico schools established the New Mexico Consortium (NMC), a nonprofit

198

Advanced Materials | ORNL  

NLE Websites -- All DOE Office Websites (Extended Search)

Research Areas Research Areas Research Highlights Facilities and Capabilities Science to Energy Solutions News & Awards Events and Conferences Supporting Organizations Directionally Solidified Materials Using high-temperature optical floating zone furnace to produce monocrystalline molybdenum alloy micro-pillars Home | Science & Discovery | Advanced Materials Advanced Materials | Advanced Materials SHARE ORNL has the nation's most comprehensive materials research program and is a world leader in research that supports the development of advanced materials for energy generation, storage, and use. We have core strengths in three main areas: materials synthesis, characterization, and theory. In other words, we discover and make new materials, we study their structure,

199

Advanced Research Materials Program  

NLE Websites -- All DOE Office Websites (Extended Search)

materials requirements for all fossil energy systems, including materials for advanced power generation and coal fuels technologies. Examples of these technologies include coal...

200

Project: Advanced Fire Detection  

Science Conference Proceedings (OSTI)

... residential fire deaths through development of measurement ... Beyond advances in sensing technologies, a key ... data will be used to develop and test ...

2013-05-30T23:59:59.000Z

Note: This page contains sample records for the topic "advanced sequential dual" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


201

advance meeting brochure  

Science Conference Proceedings (OSTI)

May 23, 1999 ... Ponte Vedra Beach, Florida, USA. ADVANCE PROGRAM ..... but she has two enclosed glass-sided decks, an out- side balcony and the...

202

Brochures | Advanced Photon Source  

NLE Websites -- All DOE Office Websites (Extended Search)

Podcasts Image Gallery external site Video Library Syndicated Feeds (RSS) The Advanced Photon Source: Lighting the Way to a Better Tomorrow aps brochure The APS helps...

203

Divisions | Advanced Photon Source  

NLE Websites -- All DOE Office Websites (Extended Search)

Chart Argonne Research Divisions APS Research Divisions In May 2002, The Advanced Photon Source was reorganized into three divisions: the Accelerator Systems Division...

204

Advanced Mixing Models  

Propose mixing indicators. Turbulence kinetic energy ... (Turbulence intensity observed at Point 8 in Tank B & C) Advanced Mixing Models. Computational Sciences. 13.

205

Advancement in Battery Materials  

Science Conference Proceedings (OSTI)

Oct 18, 2010 ... Advanced Electrochemical Storage for Renewable Integration and Utility Applications: Zhenguo "Gary" Yang1; Dawon Choi1; Gordon Graff1;...

206

OpenADR Advances  

NLE Websites -- All DOE Office Websites (Extended Search)

Volume 54 Issue 11 Date Published 112012 Keywords communication and standards, openadr, smart grid Abstract An important goal for the advancement of smart grid deployments is to...

207

DOE Advanced Protection Project  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Task 3 - Advanced Protection - Evaluate measures - 2009 - Design, model Irvine Smart Grid Demo protection system - 2010 6 Copyright 2010, Southern California Edison Task 1 -...

208

Dual-keel electrodynamic maglev system  

DOE Patents (OSTI)

A propulsion and stabilization system with a plurality of superconducting magnetic devices affixed to the dual-keels of a vehicle, where the superconducting magnetic devices produce a magnetic field when energized. The system also includes a plurality of figure-eight shaped null-flux coils affixed to opposing vertical sides of slots in a guideway. The figure-eight shaped null-flux coils are vertically oriented, laterally cross-connected in parallel, longitudinally connected in series, and continue the length of the vertical slots providing levitation and guidance force. An external power source energizes the figure-eight shaped null-flux coils to create a magnetic traveling wave that interacts with the magnetic field produced by the superconducting magnets to impart motion to the vehicle.

He, J.; Wang, Z.; Rote, D.M.; Coffey, H.T.; Hull, J.R.; Mulcahy, T.M.; Cai, Y.

1995-12-31T23:59:59.000Z

209

Dual power, constant speed electric motor system  

DOE Patents (OSTI)

A dual capacity permanent split capacitor electric motor system is provided with a stator having main and auxiliary windings. The main stator winding includes two winding sections which are connected in parallel with each other and across a pair of line terminals while the auxiliary winding is connected in series with a capacitor to form a circuit branch which is connected between the line terminals for operation at a first output power level. Switching means are provided to reconnect the main stator winding sections in series with each other and in series with a second capacitor to form a circuit branch which is connected between the line terminals while the stator auxiliary winding is connected directly between the line terminals for operation at a second output power level. Automatic rotation reversal occurs when the motor switches from the first to the second output power level.

Kirschbaum, Herbert S. (Asheville, NC)

1984-01-01T23:59:59.000Z

210

Dual-keel electrodynamic maglev system  

DOE Patents (OSTI)

A propulsion and stabilization system is disclosed with a plurality of superconducting magnetic devices affixed to the dual-keels of a vehicle, where the superconducting magnetic devices produce a magnetic field when energized. The system also includes a plurality of figure-eight shaped null-flux coils affixed to opposing vertical sides of slots in a guideway. The figure-eight shaped null-flux coils are vertically oriented, laterally cross-connected in parallel, longitudinally connected in series, and continue the length of the vertical slots providing levitation and guidance force. An external power source energizes the figure-eight shaped null-flux coils to create a magnetic traveling wave that interacts with the magnetic field produced by the superconducting magnets to impart motion to the vehicle. 6 figs.

He, J.L.; Wang, Z.; Rote, D.M.; Coffey, H.T.; Hull, J.R.; Mulcahy, T.M.; Cal, Y.

1996-12-24T23:59:59.000Z

211

Dual power, constant speed electric motor system  

DOE Patents (OSTI)

A dual capacity permanent split capacitor electric motor system is provided with a stator having main and auxiliary windings. The main stator winding includes two winding sections which are connected in parallel with each other and across a pair of line terminals while the auxiliary winding is connected in series with a capacitor to form a circuit branch which is connected between the line terminals for operation at a first output power level. Switching means are provided to reconnect the main stator winding sections in series with each other and in series with a second capacitor to form a circuit branch which is connected between the line terminals while the stator auxiliary winding is connected directly between the line terminals for operation at a second output power level. Automatic rotation reversal occurs when the motor switches from the first to the second output power level. 6 figs.

Kirschbaum, H.S.

1984-07-31T23:59:59.000Z

212

Dual neutral particle transmutation in CINDER2008  

Science Conference Proceedings (OSTI)

A capability has been built for the CINDER2008 (beta) transmutation code that expands the capability from only neutron induced reactions to photon induced reactions. This allows for two incident neutral particles to cause nuclear transmutation in a given material simultaneously. The CINDER2008 code, a modular rewrite of the CINDER'90 transmutation code from Los Alamos National Laboratory, was modified to allow for the dual sets of physics. A photonuclear cross section and photofission product yield library was also created using ENDF-B/VII data and translated neutron fission product yields. The code and library have been combined to create a unique transmutation code. The scope of use is broad; it is capable of modeling the transmutation caused by photons released from the decay of daughter and fission products as well as transmutation in photon rich environments. A brief code description and a verification and validation of the contributions are given. (authors)

Martin, W. J.; De Oliveira, C. R. E. [1 Univ. of New Mexico, MSC01 1120, Albuquerque, NM 87131-0001 (United States)

2012-07-01T23:59:59.000Z

213

Dual quark condensate and dressed Polyakov loops  

E-Print Network (OSTI)

We construct a new order parameter for finite temperature QCD by considering the quark condensate for U(1)-valued temporal boundary conditions for the fermions. Fourier transformation with respect to the boundary condition defines the dual condensate. This quantity corresponds to an equivalence class of Polyakov loops, thereby being an order parameter for the center symmetry. We explore the duality relation between the quark condensate and these dressed Polyakov loops numerically, using quenched lattice QCD configurations below and above the QCD phase transition. It is demonstrated that the Dirac spectrum responds differently to changing the boundary condition, in a manner that reproduces the expected Polyakov loop pattern. We find the dressed Polyakov loops to be dominated by the lowest Dirac modes, in contrast to thin Polyakov loops investigated earlier.

Erek Bilgici; Falk Bruckmann; Christof Gattringer; Christian Hagen

2008-01-28T23:59:59.000Z

214

Stability of chromite interconnections in dual environments  

DOE Green Energy (OSTI)

One of the most critical technical concerns in high-temperature SOFCs is the physical, chemical, and electrical stability of the interconnect (typically a doped lanthanum chromite) in the dual (oxidizing and reducing atmosphere) SOFC environment. The reducing or fuel side may experience oxygen partial pressures (P(O{sub 2})) from 10{sup {minus}18} to 10{sup {minus}6} atmospheres, while the oxidizing side may have P(O{sub 2}) from 10{sup {minus}6} to greater than 1 atm. These conditions limit the possible candidate materials to lanthanum or yttrium chromites. In the past decade, much work has centered on development of air-sinterable chromites and understanding their physical properties; little work, however, has focused on the stability of these chromites in dual environments. Chromite powders were synthesized using the glycine-nitrate process. The powders were calcined at 1,000 C for 1 hour and then uniaxially pressed into bars (46mm x 16mm x 3mm) at 55 MPa and isostatically pressed at 138 MPa. Samples were sintered in air. The dependence of the physical properties of sintered lanthanum chromites upon ambient P(O{sub 2}) and temperature (using dilatometry, thermogravimetric analysis, and oxygen permeation measurements) were studied. La{sub 1{minus}x}A{sub x}CrO{sub 3} and Y{sub 1{minus}x}Ca{sub x}CrO{sub 3}, where A is Ca or Sr and x was varied from 0.1 to 0.4 were evaluated in this study. The P(O{sub 2}) was varied using a buffered CO{sub 2}/Ar-4%H{sub 2} gas system, enabling expansion measurements to be made over a partial pressure range from 10{sup {minus}5} to 10{sup {minus}18} atmosphere at 800, 900, and 1,000 C.

Armstrong, T.R.; Stevenson, J.W.; Raney, P.; Pederson, L.R.

1994-11-01T23:59:59.000Z

215

Dual-Layer Asymmetric Microporous Silica Membranes  

DOE Green Energy (OSTI)

We report a novel sol-gel dip-coating process to form dual-layer microporous silica membranes with improved membrane performance and reproducibility. First, we deposit a surfactant-templated silica (STS) intermediate layer on top of a commercial {gamma}-alumina support both to improve its ''surface finish'' and to prevent a subsequently deposited microporous overlayer from penetrating into the support. Second, membranes are processed under clean room conditions to avoid dust contamination and, third, membranes are vacuum-calcined to promote further pore shrinkage and impart surface hydrophobicity. The resulting asymmetric membrane exhibits a gradual change in pore diameter from 50{angstrom} ({gamma}-alumina support layer) to 10-12{angstrom} (STS intermediate layer), and then to 3-4{angstrom} (30nm thick, ultramicroporous silica top-layer). Compared to a single-layer process using only the microporous overlayer, the dual-layer process improves both flux and selectivity. For the industrially important problem of natural gas purification, the combined CO{sub 2} flux [(3{approx} 0.5) x 10{sup {minus}4} cm{sup 3}(STP)/(s{center_dot}cm{sup 2}{center_dot}cm-Hg)] and CO{sub 2}/CH{sub 4} separation factors [200{approx}600] are superior to all previously reported values for separation of a 50/50 (v/v) CO{sub 2}/CH{sub 4} gas mixture. In addition, the membrane selectively separated hydrogen from a simulated reformate from partial oxidation of methanol as evidenced by a high concentration of hydrogen recovery.

TSAI,CHUNG-YI; TAM,SIU-YUE; LU,YUNFENG; BRINKER,C. JEFFREY

1999-11-19T23:59:59.000Z

216

Evaluation of a PECVD advanced barrier (k=3.7) for 32nm CMOS technology and below  

Science Conference Proceedings (OSTI)

An advanced dielectric barrier proposed for sub-45nm CMOS technology nodes is firstly characterized on 300mm full sheet wafers. The barrier is a bi-layer deposited by PECVD. The copper diffusion barrier property is ensured by a depositing dense initiation ... Keywords: Dielectric barrier, Dual damascene, Electromigration, Etch stop layer, RC delay

L. L. Chapelon; E. Petitprez; P. Brun; A. Farcy; J. Torres

2007-11-01T23:59:59.000Z

217

Kansas Advanced Semiconductor Project  

SciTech Connect

KASP (Kansas Advanced Semiconductor Project) completed the new Layer 0 upgrade for D0, assumed key electronics projects for the US CMS project, finished important new physics measurements with the D0 experiment at Fermilab, made substantial contributions to detector studies for the proposed e+e- international linear collider (ILC), and advanced key initiatives in non-accelerator-based neutrino physics.

Baringer, P.; Bean, A.; Bolton, T.; Horton-Smith, G.; Maravin, Y.; Ratra, B.; Stanton, N.; von Toerne, E.; Wilson, G.

2007-09-21T23:59:59.000Z

218

Advanced Windows Test Facility  

NLE Websites -- All DOE Office Websites (Extended Search)

Exterior of Advanced Windows Test Facility Exterior of Advanced Windows Test Facility Advanced Windows Test Facility This multi-room laboratory's purpose is to test the performance and properties of advanced windows and window systems such as electrochromic windows, and automatically controlled shutters and blinds. The lab simulates real-world office spaces. Embedded instrumentation throughout the lab records solar gains and losses for specified time periods, weather conditions, energy use, and human comfort indicators. Electrochromic glazings promise to be a major advance in energy-efficient window technology, helping to achieve the goal of transforming windows and skylights from an energy liability in buildings to an energy source. The glazing can be reversibly switched from a clear to a transparent, colored

219

Advanced Fuels Synthesis  

NLE Websites -- All DOE Office Websites (Extended Search)

Advanced Fuels Synthesis Advanced Fuels Synthesis Coal and Coal/Biomass to Liquids Advanced Fuels Synthesis The Advanced Fuels Synthesis Key Technology is focused on catalyst and reactor optimization for producing liquid hydrocarbon fuels from coal/biomass mixtures, supports the development and demonstration of advanced separation technologies, and sponsors research on novel technologies to convert coal/biomass to liquid fuels. Active projects within the program portfolio include the following: Fischer-Tropsch fuels synthesis Small Scale Coal Biomass Liquids Production Using Highly Selective Fischer Tropsch Catalyst Small Scale Pilot Plant for the Gasification of Coal and Coal/Biomass Blends and Conversion of Derived Syngas to Liquid Fuels Via Fischer-Tropsch Synthesis Coal Fuels Alliance: Design and Construction of Early Lead Mini Fischer-Tropsch Refinery

220

Self-dual teleparallel gravity and the positive energy theorem  

E-Print Network (OSTI)

A self-dual and anti-self-dual decomposition of the teleparallel gravity is carried out and the self-dual Lagrangian of the teleparallel gravity which is equivalent to the Ashtekar Lagrangian in vacuum is obtained. Its Hamiltonian formulation and the constraint analysis are developed. Starting from Witten's equation Nester's gauge condition is derived directly and a new expression of the boundary term is obtained. Using this expression and Witten's identity the proof of the positive energy theorem by Nester et al is extended to a case including momentum.

G. Y. Chee

2004-08-16T23:59:59.000Z

Note: This page contains sample records for the topic "advanced sequential dual" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


221

Dual-hop LANs using station wavelength routing  

Science Conference Proceedings (OSTI)

Abstract: In future WDM local area networks, the number of available wavelengths may initially be fairly modest. As a result, spatial reuse is required in order to obtain designs which will support a reasonable number of stations. A dual-hop architecture ... Keywords: ATM buffer/switch components, WDM local area networks, all-optical approaches, buffering stage, control strategies, dual-hop LAN, dual-hop architecture, electronic implementations, hybrid electro-optic designs, local optical network, multiple wavelength sharing, optical fibre LAN, spatial reuse, station wavelength routing, system performance, traffic models, wavelength agility

1995-09-01T23:59:59.000Z

222

Dual-Mode Hybrid/Two-Mode Hybrid Accomplishment  

NLE Websites -- All DOE Office Websites (Extended Search)

Dual-Mode Hybrid/Two-Mode Hybrid Accomplishment Dual-Mode Hybrid/Two-Mode Hybrid Accomplishment DOE-funded research, in collaboration with Allison Buses and General Motors Corporation has led to the commercialization of a dramatically different hybrid transmission system for heavy-duty and light-duty applications. The Dual-Mode or Two-Mode hybrid system is an infinitely variable speed hybrid transmission that works with the engine and battery system and automatically chooses to operate in a parallel or series hybrid path to maximize efficiency and minimize emissions, fuel consumption and noise. Parallel and Series hybrid configurations are found on most hybrid vehicles today, both with their own pluses and minuses. The Dual- Mode/Two-Mode systems uses the positive characteristics from both systems to maximize fuel

223

Mesocyclone and Microburst Signature Distortion with Dual PRT Radars  

Science Conference Proceedings (OSTI)

A simple model is used to illustrate the limitations of dual pulse repetition time (PRT) radars for measurements of wind fields with strong horizontal wind gradients. In such conditions, errors may occur even if the radial velocity measurements ...

Peter T. May

2001-07-01T23:59:59.000Z

224

DARHT: Dual-Axis Radiographic Hydrodynamic Test Facility  

NLE Websites -- All DOE Office Websites (Extended Search)

DARHT: Dual-Axis Radiographic Hydrodynamic Test Facility DARHT: Dual-Axis Radiographic Hydrodynamic Test Facility DARHT: Dual-Axis Radiographic Hydrodynamic Test Facility DARHT, supports a critical component of LANL's primary mission: to ensure the safety, security, and effectiveness of nuclear weapons in our nation's stockpile. Los Alamos scientists built DARHT, the world's most powerful x-ray machine, to analyze mockups of nuclear weapons. At the Los Alamos National Laboratory (LANL), the Dual-Axis Radiographic Hydrodynamic Test Facility, or DARHT, supports a critical component of LANL's primary mission: to ensure the safety, security, and effectiveness of nuclear weapons in our nation's stockpile. Los Alamos scientists built DARHT, the world's most powerful x-ray machine, to analyze mockups of nuclear weapons.

225

Fusing strategies for the dual-voltage fault  

E-Print Network (OSTI)

This thesis focuses on the 42V - 14V fault in a dual voltage system and discusses the possibility of effective fusing. A simple model for the system had been created from technical documentation. Based on the model and the ...

Shrivastava, Rupam, 1981-

2005-01-01T23:59:59.000Z

226

New developments in the primal-dual column generation technique  

E-Print Network (OSTI)

Jan 24, 2011 ... Email: J.Gondzio@ed.ac.uk. School of ... Brevis@sms.ed.ac.uk. Partially ...... Solving real-world linear ordering problems using a primal-dual.

227

A Dual-Wavelength Radar Method to Measure Snowfall Rate  

Science Conference Proceedings (OSTI)

A dual-wavelength radar method to estimate snowfall rate has been developed. The method suggests taking simultaneous and collocated reflectivity measurements at two radar wavelengths. Snowfall backscattering at one of these wavelengths should be ...

Sergey Y. Matrosov

1998-11-01T23:59:59.000Z

228

Dual Superconductivity and Chiral Symmetry in Full QCD  

E-Print Network (OSTI)

A disorder parameter detecting dual superconductivity of the vacuum is measured across the chiral phase transition in full QCD with two flavours of dynamical staggered fermions. The observed behaviour is similar to the quenched case.

J. M. Carmona; M. D'Elia; L. Del Debbio; A. Di Giacomo; B. Lucini; G. Paffuti

2001-10-12T23:59:59.000Z

229

Dual volatility and dependence parameters and the copula  

Science Conference Proceedings (OSTI)

We introduce some new species into the zoo of stochastic volatility and dependence parameters. We start with average absolute deviation and Gini index, which are elementary volatility parameters of first and second order in spirit of dual theory of choice ...

Dieter Denneberg; Nikola Leufer

2008-08-01T23:59:59.000Z

230

Antenna Beam Patterns and Dual-Wavelength Processing  

Science Conference Proceedings (OSTI)

The detection of hail with a dual-wavelength radar system can succeed only when the two essentially independent radars used are correctly calibrated, when attenuation is correctly handled, and when the radars sample the same volume in space. The ...

Ronald E. Rinehart; John D. Tuttle

1982-12-01T23:59:59.000Z

231

INCREASED STRENGTHENING OF AUSTENITIC ALLOYS THROUGH DUAL AGING  

E-Print Network (OSTI)

d o - - -700°C after first aging at 745°C /2 hr tween) (nobJ,J". _.J__ __JI (TOTAL) AGING TIME (hr) XBL Figure 22 aALLOYS THROUGH DUAL AGING Annie Ma Inorganic Materials

Ma, Annie

2011-01-01T23:59:59.000Z

232

On the Relationship Between Dual Photography and Classical Ghost Imaging  

E-Print Network (OSTI)

Classical ghost imaging has received considerable attention in recent years because of its remarkable ability to image a scene without direct observation by a light-detecting imaging device. In this article, we show that this imaging process is actually a realization of a paradigm known as dual photography, which has been shown to produce full-color dual (ghost) images of 3D objects with complex materials without using a traditional imaging device. Specifically, we demonstrate mathematically that the cross-correlation based methods used to recover ghost images are equivalent to the light transport measurement process of dual photography. Because of this, we are able to provide a new explanation for ghost imaging using only classical optics by leveraging the principle of reciprocity in classical electromagnetics. This observation also shows how to leverage previous work on light transport acquisition and dual photography to improve ghost imaging systems in the future.

Pradeep Sen

2013-09-12T23:59:59.000Z

233

Ground Clutter Filtering Dual-Polarized, Staggered PRT Sequences  

Science Conference Proceedings (OSTI)

A procedure to filter the ground clutter from a dual-polarized, staggered pulse repetition time (PRT) sequence and recover the complex spectral coefficients of the weather signal is presented. While magnitude spectra are sufficient for estimation ...

M. Sachidananda; Dusan S. Zrnic

2006-08-01T23:59:59.000Z

234

Remote Sensing of Hail with a Dual Linear Polarization Radar  

Science Conference Proceedings (OSTI)

A technique for the remote sensing of hail with an S-band dual linear polarization radar is described. The method employs a new hail signal HDR, which is derived from disdrometer measurements of raindrop size distributions. Experimental ...

K. Aydin; T. A. Seliga; V. Balaji

1986-10-01T23:59:59.000Z

235

A Dual-Frequency Microwave Technique for Measuring Rainwater Content  

Science Conference Proceedings (OSTI)

While there are many microwave techniques for estimating the rainfall rate, there are presently few if any for accurately determining the rainwater content (W). This study shows that the dual-frequency (38, 25 GHZ) differential attenuation (A38?...

A. R. Jameson

1992-02-01T23:59:59.000Z

236

Modeling and torque estimation of an automotive dual mass flywheel  

Science Conference Proceedings (OSTI)

The Dual Mass Flywheel (DMF) is primarily used for dampening of oscillations in automotive powertrains and to prevent gearbox rattling. This paper explains the DMF mechanics along with its application and components. Afterwards a detailed ab-inltio model ...

Ulf Schaper; Oliver Sawodny; Tobias Mahl; Uli Blessing

2009-06-01T23:59:59.000Z

237

EIS-0228: Dual Axis Radiographic Hydrodynamic Test (DARHT) Facility  

Energy.gov (U.S. Department of Energy (DOE))

This EIS evaluates the potential environmental impact of a proposal to construct and operate theDual Axis Radiographic Hydrodynamic Test (DARHT) facility at Los Alamos National Laboratory (LANL)...

238

Record of Decision Dual Axis Radiographic Hydrodynamic Test Facility  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

8:45 am BILLING CODE 6450-01-P Record of Decision Dual Axis Radiographic Hydrodynamic Test Facility AGENCY: Department of Energy. ACTION: Record of decision. SUMMARY: The...

239

Processing and Interpretation of Coherent Dual-Polarized Radar Measurements  

Science Conference Proceedings (OSTI)

Dual-polarized coherent radar measurements are used to estimate the differential propagation phase or DP between horizontal and vertical polarization states. The slope of DP is an estimate of the specific differential phase KDP. This process is ...

J. Hubbert; V. Chandrasekar; V. N. Bringi; P. Meischner

1993-04-01T23:59:59.000Z

240

Fuel cell having dual electrode anode or cathode  

DOE Patents (OSTI)

A fuel cell that is characterized by including a dual electrode anode that is operable to simultaneously electro-oxidize a gaseous fuel and a liquid fuel. In alternative embodiments, a fuel cell having a single electrode anode is provided with a dual electrode cathode that is operable to simultaneously reduce a gaseous oxidant and a liquid oxidant to electro-oxidize a fuel supplied to the cell.

Findl, Eugene (Coram, NY)

1985-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "advanced sequential dual" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


241

Fuel cell having dual electrode anode or cathode  

DOE Patents (OSTI)

A fuel cell that is characterized by including a dual electrode anode that is operable to simultaneously electro-oxidize a gaseous fuel and a liquid fuel. In alternative embodiments, a fuel cell having a single electrode anode is provided with a dual electrode cathode that is operable to simultaneously reduce a gaseous oxidant and a liquid oxidant to electro-oxidize a fuel supplied to the cell.

Findl, E.

1984-04-10T23:59:59.000Z

242

Dual flow--temperature--humidity control system operating manual  

SciTech Connect

The manual contains operating, maintenance, and troubleshooting procedures for a dual flow--temperature--humidity control system used at the Lawrence Livermore Laboratory to prepare test atmospheres for industrial hygiene and air pollution studies. The system consists of two basic components: a commercially available temperature/humidity indicator unit and a specially built dual flow--temperature--humidity control module that provides two air sources controlled at the same conditions of flow, temperature, and relative humidity.

Nelson, G.O.; Taylor, R.D.

1978-12-15T23:59:59.000Z

243

QCD String as Vortex String in Seiberg-Dual Theory  

E-Print Network (OSTI)

We construct a classical vortex string solution in a Seiberg-dual theory of N=1 supersymmetric SO(N_c) QCD which flows to a confining phase. We claim that this vortex string is a QCD string, as previouly argued by M.Strassler. In SO(N_c) QCD, it is known that stable QCD strings exist even in the presence of dynamical quarks. We show that our vortex strings are stable in the Seiberg-dual theory.

Eto, Minoru; Terashima, Seiji

2007-01-01T23:59:59.000Z

244

The Philosophy and Feasibility of Dual Readout Calorimetry  

SciTech Connect

I will discuss the general physical ideas behind dual-readout calorimetry, their implementation in DREAM (Dual REAdout Module) with exact separation of scintillation and Cerenkov light, implementation with mixed light in DREAM fibers, anticipated implementation in PbWO4 crystals with applications to the 4th Concept detector and to CMS, use in high energy gamma-ray and cosmic ray astrophysics with Cerenkov and N2 fluorescent light, and implementation in the 4th Concept detector for muon identification.

Hauptman, John [Physics, Iowa State University, Ames IA 50011 (United States)

2006-10-27T23:59:59.000Z

245

A sequential partly iterative approach for multicomponent reactive transport with CORE2D  

SciTech Connect

CORE{sup 2D} V4 is a finite element code for modeling partly or fully saturated water flow, heat transport and multicomponent reactive solute transport under both local chemical equilibrium and kinetic conditions. It can handle coupled microbial processes and geochemical reactions such as acid-base, aqueous complexation, redox, mineral dissolution/precipitation, gas dissolution/exsolution, ion exchange, sorption via linear and nonlinear isotherms, sorption via surface complexation. Hydraulic parameters may change due to mineral precipitation/dissolution reactions. Coupled transport and chemical equations are solved by using sequential iterative approaches. A sequential partly-iterative approach (SPIA) is presented which improves the accuracy of the traditional sequential noniterative approach (SNIA) and is more efficient than the general sequential iterative approach (SIA). While SNIA leads to a substantial saving of computing time, it introduces numerical errors which are especially large for cation exchange reactions. SPIA improves the efficiency of SIA because the iteration between transport and chemical equations is only performed in nodes with a large mass transfer between solid and liquid phases. The efficiency and accuracy of SPIA are compared to those of SIA and SNIA using synthetic examples and a case study of reactive transport through the Llobregat Delta aquitard in Spain. SPIA is found to be as accurate as SIA while requiring significantly less CPU time. In addition, SPIA is much more accurate than SNIA with only a minor increase in computing time. A further enhancement of the efficiency of SPIA is achieved by improving the efficiency of the Newton-Raphson method used for solving chemical equations. Such an improvement is obtained by working with increments of log-concentrations and ignoring the terms of the Jacobian matrix containing derivatives of activity coefficients. A proof is given for the symmetry and non-singularity of the Jacobian matrix. Numerical analyses performed with synthetic examples confirm that these modifications improve the efficiency and convergence of the iterative algorithm.

Samper, J.; Xu, T.; Yang, C.

2008-11-01T23:59:59.000Z

246

Sequential suppression of quarkonia and high-energy nucleus-nucleus collisions  

E-Print Network (OSTI)

According to the usual application of the sequential-suppression picture to the dynamics of heavy quarkonia in the hot medium formed in ultrarelativistic nuclear collisions, quark-antiquark pairs created in a given bound or unbound state remain in that same state as the medium evolves. We argue that this scenario implicitly assumes an adiabatic evolution of the quarkonia, and we show that the validity of the adiabaticity assumption is questionable.

Dutta, Nirupam

2012-01-01T23:59:59.000Z

247

NETL: Advanced Research  

NLE Websites -- All DOE Office Websites (Extended Search)

AR AR Coal and Power Systems Advanced Research 12.11.13: Request for Information entitled "Novel Crosscutting Research and Development to Support Advanced Energy Systems". Application due date is January 15, 2014. The RFI and/or instructions can be found on the FedConnect site at FedConnect. Achieving Successes in High Performance Materials, Coal Utilization Sciences, Sensors & Controls Innovations, Computational Energy Sciences, Cooperative Research and Development, and sponsoring Education Initiatives. The Advanced Research (AR) program within NETL's Office of Coal and Power Systems fosters the development of innovative, cost-effective technologies for improving the efficiency and environmental performance of advanced coal and power systems. In addition, AR bridges the gap between fundamental

248

Advanced Chlorophyll Fluorometer  

To advance miniaturization of the AquaSentinel environmental monitoring technology, ORNL and the University of Tennessee researchers developed a microfluidics-based pulse amplitude modulation (PAM) chlorophyll fluorometerthe first of its ...

249

Advancement of Electrochromic Windows  

E-Print Network (OSTI)

Research Energy Systems Integration Advancement ofintegration issues related to using EC windows within a whole building energy efficient systemenergy- savings benefit with EC-daylighting-HVAC integration (assuming a conventional VAV system

2006-01-01T23:59:59.000Z

250

Advanced Cathode Catalysts  

NLE Websites -- All DOE Office Websites (Extended Search)

Fuel Cell Research 1 HFCIT Program Kick-off Meeting, Arlington, VA, February 13-14, 2007 Program Kick-off Meeting Arlington, Virginia, February 13-14, 2007 Advanced Cathode...

251

Search Asia Advanced Search  

E-Print Network (OSTI)

Asia Times Search Asia Times Advanced Search Southeast Asia Malaysia tackles illegal logging:52:14 AM Search #12;Asia Times illegal logging," he said, adding that nine Malaysians had been arrested

252

Search Asia Advanced Search  

E-Print Network (OSTI)

Asia Times Search Asia Times Advanced Search Southeast Asia Indonesia looks to curb log smuggling.html (1 of 2)9/4/2007 12:59:34 PM Search #12;Asia Times No material from Asia Times Online may

253

About | Advanced Photon Source  

NLE Websites -- All DOE Office Websites (Extended Search)

the APS Welcome to the Advanced Photon Source Here you will find an introduction and tour of the facility, as well as information about the organizations and opportunities at...

254

Nanostructured Materials for Advanced  

E-Print Network (OSTI)

of electric vehicles (EVs) and hybrid electric vehicles (HEVs). High energy and high power densitiesT Nanostructured Materials for Advanced Li-Ion Rechargeable Batteries THE RECENT INCREASE IN demand

Cao, Guozhong

255

DYNAMIC ANALYSIS OF THE BULK TRITIUM SHIPPING PACKAGE SUBJECTED TO CLOSURE TORQUES AND SEQUENTIAL IMPACTS  

SciTech Connect

This paper presents a finite-element technique to simulate the structural responses and to evaluate the cumulative damage of a radioactive material packaging requiring bolt closure-tightening torque and subjected to the scenarios of the Hypothetical Accident Conditions (HAC) defined in the Code of Federal Regulations Title 10 part 71 (10CFR71). Existing finite-element methods for modeling closure stresses from bolt pre-load are not readily adaptable to dynamic analyses. The HAC events are required to occur sequentially per 10CFR71 and thus the evaluation of the cumulative damage is desirable. Generally, each HAC event is analyzed separately and the cumulative damage is partially addressed by superposition. This results in relying on additional physical testing to comply with 10CFR71 requirements for assessment of cumulative damage. The proposed technique utilizes the combination of kinematic constraints, rigid-body motions and structural deformations to overcome some of the difficulties encountered in modeling the effect of cumulative damage. This methodology provides improved numerical solutions in compliance with the 10CFR71 requirements for sequential HAC tests. Analyses were performed for the Bulk Tritium Shipping Package (BTSP) designed by Savannah River National Laboratory to demonstrate the applications of the technique. The methodology proposed simulates the closure bolt torque preload followed by the sequential HAC events, the 30-foot drop and the 30-foot dynamic crush. The analytical results will be compared to the package test data.

Wu, T; Paul Blanton, P; Kurt Eberl, K

2007-07-09T23:59:59.000Z

256

Dual excitation acoustic paramagnetic logging tool  

DOE Patents (OSTI)

New methods and apparatus are disclosed which allow measurement of the presence of oil and water in geological formations using a new physical effect called the Acoustic Paramagnetic Logging Effect (APLE). The presence of petroleum in formation causes a slight increase in the earth's magnetic field in the vicinity of the reservoir. This is the phenomena of paramagnetism. Application of an acoustic source to a geological formation at the Larmor frequency of the nucleons present causes the paramagnetism of the formation to disappear. This results in a decrease in the earth's magnetic field in the vicinity of the oil bearing formation. Repetitively frequency sweeping the acoustic source through the Larmor frequency of the nucleons present (approx. 2 kHz) causes an amplitude modulation of the earth's magnetic field which is a consequence of the APLE. The amplitude modulation of the earth's magnetic field is measured with an induction coil gradiometer and provides a direct measure of the amount of oil and water in the excitation zone of the formation. The phase of the signal is used to infer the longitudinal relaxation times of the fluids present, which results in the ability in general to separate oil and water and to measure the viscosity of the oil present. Such measurements may be performed in open boreholes and in cased well bores. The Dual Excitation Acoustic Paramagnetic Logging Tool employing two acoustic sources is also described. 6 figs.

Vail, W.B. III.

1989-02-14T23:59:59.000Z

257

Dual excitation acoustic paramagnetic logging tool  

DOE Patents (OSTI)

New methods and apparatus are disclosed which allow measurement of the presence of oil and water in gelogical formations using a new physical effect called the Acoustic Paramagnetic Logging Effect (APLE). The presence of petroleum in formation causes a slight increase in the earth's magnetic field in the vicinity of the reservoir. This is the phenomena of paramagnetism. Application of an acoustic source to a geological formation at the Larmor frequency of the nucleous present causes the paramagnetism of the formation to disappear. This results in a decrease in the earth's magnetic field in the vicinity of the oil bearing formation. Repetitively frequency sweeping the acoustic source through the Larmor frequency of the nucleons present (approx. 2 kHz) causes an amplitude modulation of the earth's magnetic field which is a consequence of the APLE. The amplitude modulation of the earth's magnetic field is measured with an induction coil gradiometer and provides a direct measure of the amount of oil and water in the excitation zone of the formation. The phase of the signal is used to infer the longitudinal relaxation times of the fluids present, which results in the ability in general to separate oil and water and to measure the viscosity of the oil present. Such measurements may be preformed in open boreholes and in cased well bores. The Dual Excitation Acoustic Paramagnetic Logging Tool employing two acoustic sources is also described.

Vail, III, William B. (Bothell, WA)

1989-01-01T23:59:59.000Z

258

Dual mode stereotactic localization method and application  

DOE Patents (OSTI)

The invention described herein combines the structural digital X-ray image provided by conventional stereotactic core biopsy instruments with the additional functional metabolic gamma imaging obtained with a dedicated compact gamma imaging mini-camera. Before the procedure, the patient is injected with an appropriate radiopharmaceutical. The radiopharmaceutical uptake distribution within the breast under compression in a conventional examination table expressed by the intensity of gamma emissions is obtained for comparison (co-registration) with the digital mammography (X-ray) image. This dual modality mode of operation greatly increases the functionality of existing stereotactic biopsy devices by yielding a much smaller number of false positives than would be produced using X-ray images alone. The ability to obtain both the X-ray mammographic image and the nuclear-based medicine gamma image using a single device is made possible largely through the use of a novel, small and movable gamma imaging camera that permits its incorporation into the same table or system as that currently utilized to obtain X-ray based mammographic images for localization of lesions.

Keppel, Cynthia E. (Norfolk, VA); Barbosa, Fernando Jorge (Newport News, VA); Majewski, Stanislaw (Grafton, VA)

2002-01-01T23:59:59.000Z

259

Advanced Distribution Monitoring  

Science Conference Proceedings (OSTI)

Advanced Distribution Automation (ADA) is a concept for a fully controllable and flexible distribution system that will facilitate the exchange of electrical energy AND information between participants and system components. Advances in the monitoring of system parameters like voltages, currents and breaker/switch positions as well as environmental variables like temperature and wind speed will be required in order to fully implement ADA. This report presents background information on distribution monito...

2005-12-05T23:59:59.000Z

260

Advanced drilling systems study  

DOE Green Energy (OSTI)

This work was initiated as part of the National Advanced Drilling and Excavation Technologies (NADET) Program. It is being performed through joint finding from the Department of Energy Geothermal Division and the Natural Gas Technology Branch, Morgantown Energy Technology Center. Interest in advanced drilling systems is high. The Geothermal Division of the Department of Energy has initiated a multi-year effort in the development of advanced drilling systems; the National Research Council completed a study of drilling and excavation technologies last year; and the MIT Energy Laboratory recently submitted a proposal for a national initiative in advanced drilling and excavation research. The primary reasons for this interest are financial. Worldwide expenditures on oil and gas drilling approach $75 billion per year. Also, drilling and well completion account for 25% to 50% of the cost of producing electricity from geothermal energy. There is incentive to search for methods to reduce the cost of drilling. Work on ideas to improve or replace rotary drilling technology dates back at least to the 1930`s. There was a significant amount of work in this area in the 1960`s and 1970`s; and there has been some continued effort through the 1980`s. Undoubtedly there are concepts for advanced drilling systems that have yet to be studied; however, it is almost certain that new efforts to initiate work on advanced drilling systems will build on an idea or a variation of an idea that has already been investigated. Therefore, a review of previous efforts coupled with a characterization of viable advanced drilling systems and the current state of technology as it applies to those systems provide the basis for the current study of advanced drilling.

Pierce, K.G. [Sandia National Labs., Albuquerque, NM (United States); Livesay, B.J. [Livesay Consultants, San Diego, CA (United States)

1995-03-01T23:59:59.000Z

Note: This page contains sample records for the topic "advanced sequential dual" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


261

NETL: Advanced NOx Emissions Control  

NLE Websites -- All DOE Office Websites (Extended Search)

Home > Technologies > Coal & Power Systems > Innovations for Existing Plants > Advanced NOx Emissions Control Innovations for Existing Plants Advanced NOx Emissions Control Adv....

262

Advance Electronics | Open Energy Information  

Open Energy Info (EERE)

Advance Electronics Jump to: navigation, search Name Advance Electronics Place United Kingdom Zip LL14 3YR Product Develop and deliver power conditioners, transient suppressors,...

263

Sequential Assimilation of ERS-1 SAR Data into a Coupled Land SurfaceHydrological Model Using an Extended Kalman Filter  

Science Conference Proceedings (OSTI)

A first attempt to sequentially assimilate European Space Agency (ESA) Remote Sensing Satellite (ERS) synthetic aperture radar (SAR) estimations of surface soil moisture in the production scheme of a lumped rainfallrunoff model has been ...

C. Francois; A. Quesney; C. Ottl

2003-04-01T23:59:59.000Z

264

Advanced Vehicle Technologies Awards | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Advanced Vehicle Technologies Awards Advanced Vehicle Technologies Awards Microsoft Word - VTP 175 Advanced Vehicle Tech project descriptions draft v5 8-2-11 AdvancedVehiclesTechn...

265

CS4353 Course Outline Advanced Graphics ?  

E-Print Network (OSTI)

Introduce advanced interactive computer graphics concepts Introduce advanced architecture of computer graphics devices Introduce advanced mathematical representation of graphic images Develop advanced graphics programming skills

Instructor John; E. Howl

2009-01-01T23:59:59.000Z

266

NETL: Advanced Research - Successes  

NLE Websites -- All DOE Office Websites (Extended Search)

Successes Successes Advanced Research Successes Sensors & Controls "...Optical grade single-crystal sapphire optical fiber waveguides are especially attractive for fabricating sensors for the harsh high-temperature, corrosive environments found in gasifiers." Read More... "Industry adoption of CCADS will open the door to a new generation of more efficient, ultra-low emission turbines in advanced energy systems" Read More... Bioprocessing " Successful development and commercial application of this environmentally safe bacterial toxin will allow power plants to reduce or eliminate the use of chlorination, reducing the risk of harmful effects on aquatic ecosystems." Advanced Materials " This project will benefit gasification technology development and deployment by improving materials to contain and monitor gasification processes." Read More...

267

Geothermal: Advanced Search  

NLE Websites -- All DOE Office Websites (Extended Search)

Advanced Search Advanced Search Geothermal Technologies Legacy Collection Help/FAQ | Site Map | Contact Us | Admin Log On Home/Basic Search About Publications Advanced Search New Hot Docs News Related Links You may need to turn on Javascript in your browser to use the Find Subject and Find Author features. Sort By: Relevance Publication Date System Entry Date Document Type Title Research Org Sponsoring Org OSTI Identifier Report Number DOE Contract Number Ascending Descending Enter search criteria into as few or as many fields as desired. Search In For Term(s) (Place phrase in "double quotes") All Fields: Bibliographic Data: Full Text: Creator/Author Select : Title: Subject Select : Identifier Numbers: Journal Info.: Conference Info.: Patent Info.: Research Org.: Sponsoring Org.:

268

NIST's Advanced Technology Program  

NLE Websites -- All DOE Office Websites (Extended Search)

NIST's Advanced NIST's Advanced Technology Program NIST's Advanced Technology Program DOE Workshop on Hydrogen Separation and Purification Technologies Arlington, VA, Sept. 8-9, 2004 Jason Huang 301-975-4197 National Institute of Standards and Technology 100 Bureau Drive Stop 4730 Gaithersburg, MD 20899-4730 http://www.atp.nist.gov National Institute of Standards and Technology * Technology Administration * U.S. Department of Commerce ATP is part of NIST Helping America Measure Up NIST Mission ATP is part of NIST NIST Mission: Strengthen the U.S. economy and improve the quality of life by working with industry to develop and apply technology, measurements, and standards. * * * * * * 3,000 employees $771 million annual budget 2,000 field agents 1,800 guest researchers $2.2 billion co-funding of

269

Advanced Hydride Laboratory  

DOE Green Energy (OSTI)

Metal hydrides have been used at the Savannah River Tritium Facilities since 1984. However, the most extensive application of metal hydride technology at the Savannah River Site is being planned for the Replacement Tritium Facility, a $140 million facility schedules for completion in 1990 and startup in 1991. In the new facility, metal hydride technology will be used to store, separate, isotopically purify, pump, and compress hydrogen isotopes. In support of the Replacement Tritium Facility, a $3.2 million, cold,'' process demonstration facility, the Advanced Hydride Laboratory began operation in November of 1987. The purpose of the Advanced Hydride Laboratory is to demonstrate the Replacement Tritium Facility's metal hydride technology by integrating the various unit operations into an overall process. This paper will describe the Advanced Hydride Laboratory, its role and its impact on the application of metal hydride technology to tritium handling.

Motyka, T.

1989-01-01T23:59:59.000Z

270

Initial Tests Of The Dual-Sweep Streak Camera System Planned For Aps Particle-Beam Diagnostics*  

E-Print Network (OSTI)

Initial tests of a dual-sweep streak system planned for use on the Advanced Photon Source (APS) have been performed using assets of the Argonne Wakefield Accelerator (AWA) facility. The short light pulses from the photoelectric injector drive laser in both the visible (l=496 nm, Dt~1.5 ps (FWHM)), and the ultraviolet (l= 248 nm, Dt~5 ps (FWHM)) were used. Both a UV-visible S20 photocathode streak tube and a UV-tox -ray Au photocathode streak tube were tested. Calibration data with an etalon were also obtained. A sample of dualsweep streak data using optical synchrotron radiation on the APS injector synchrotron is also presented. I. INTRODUCTION The Advanced Photon Source will be a third-generation synchrotron radiation facility for the hard x-ray (10-100 keV) research community. The need to measure and monitor particle and photon beam parameters in the single bunch (10 ps), bunch-to-bunch (3 to 180 ns), and turn-by-turn (3.68 s) timescales has resulted in the choice of a dual-sweep s...

Lumpkin Yang And; A. Lumpkin; B. Yang; W. Gai; W. Cieslik

1995-01-01T23:59:59.000Z

271

Advanced fuel chemistry for advanced engines.  

SciTech Connect

Autoignition chemistry is central to predictive modeling of many advanced engine designs that combine high efficiency and low inherent pollutant emissions. This chemistry, and especially its pressure dependence, is poorly known for fuels derived from heavy petroleum and for biofuels, both of which are becoming increasingly prominent in the nation's fuel stream. We have investigated the pressure dependence of key ignition reactions for a series of molecules representative of non-traditional and alternative fuels. These investigations combined experimental characterization of hydroxyl radical production in well-controlled photolytically initiated oxidation and a hybrid modeling strategy that linked detailed quantum chemistry and computational kinetics of critical reactions with rate-equation models of the global chemical system. Comprehensive mechanisms for autoignition generally ignore the pressure dependence of branching fractions in the important alkyl + O{sub 2} reaction systems; however we have demonstrated that pressure-dependent 'formally direct' pathways persist at in-cylinder pressures.

Taatjes, Craig A.; Jusinski, Leonard E.; Zador, Judit; Fernandes, Ravi X.; Miller, James A.

2009-09-01T23:59:59.000Z

272

Advanced Containment System  

SciTech Connect

An advanced containment system for containing buried waste and associated leachate. The advanced containment system comprises a plurality of casing sections with each casing section interlocked to an adjacent casing section. Each casing section includes a complementary interlocking structure that interlocks with the complementary interlocking structure on an adjacent casing section. A barrier filler substantially fills the casing sections and may substantially fill the spaces of the complementary interlocking structure to form a substantially impermeable barrier. Some of the casing sections may include sensors so that the casing sections and the zone of interest may be remotely monitored after the casing sections are emplaced in the ground.

Kostelnik, Kevin M. (Idaho Falls, ID); Kawamura, Hideki (Tokyo, JP); Richardson, John G. (Idaho Falls, ID); Noda, Masaru (Tokyo, JP)

2005-02-08T23:59:59.000Z

273

Advanced Monitoring systems initiative  

SciTech Connect

The Advanced Monitoring Systems Initiative (AMSI) actively searches for promising technologies and aggressively moves them from the research bench into DOE/NNSA end-user applications. There is a large unfulfilled need for an active element that reaches out to identify and recruit emerging sensor technologies into the test and evaluation function. Sensor research is ubiquitous, with the seeds of many novel concepts originating in the university systems, but at present these novel concepts do not move quickly and efficiently into real test environments. AMSI is a widely recognized, self-sustaining ''business'' accelerating the selection, development, testing, evaluation, and deployment of advanced monitoring systems and components.

R.J. Venedam; E.O. Hohman; C.F. Lohrstorfer; S.J. Weeks; J.B. Jones; W.J. Haas

2004-09-30T23:59:59.000Z

274

Advanced Simulation and Computing  

National Nuclear Security Administration (NNSA)

NA-ASC-117R-09-Vol.1-Rev.0 NA-ASC-117R-09-Vol.1-Rev.0 Advanced Simulation and Computing PROGRAM PLAN FY09 October 2008 ASC Focal Point Robert Meisner, Director DOE/NNSA NA-121.2 202-586-0908 Program Plan Focal Point for NA-121.2 Njema Frazier DOE/NNSA NA-121.2 202-586-5789 A Publication of the Office of Advanced Simulation & Computing, NNSA Defense Programs i Contents Executive Summary ----------------------------------------------------------------------------------------------- 1 I. Introduction -------------------------------------------------------------------------------------------------------- 2 Realizing the Vision ------------------------------------------------------------------------------------------------- 2 The Future of the Nuclear Weapons Complex ---------------------------------------------------------------- 2

275

Dynamic simulation of dual-speed wind turbine generation  

SciTech Connect

Induction generators have been used since the early development of utility-scale wind turbine generation. An induction generator is the generator of choice because of its ruggedness, and low cost. With an induction generator, the operating speed of the wind turbine is limited to a narrow range (almost constant speed). Dual- speed operation can be accomplished by using an induction generator with two different sets of winding configurations or by using two induction generators with two different rated speeds. With single- speed operation, the wind turbine operates at different power coefficients (Cp) as the wind speed varies. The operation at maximum Cp can occur only at a single wind speed. However, if the wind speed varies across a wider range, the operating Cp will vary significantly. Dual-speed operation has the advantage of enabling the wind turbine to operate at near maximum Cp over a wider range of wind-speeds. Thus, annual energy production can be increased. The dual-speed mode may generate less energy than a variable-speed mode; nevertheless, it offers an alternative to capture more energy than single-speed operation. In this paper, dual-speed operation of a wind turbine will be investigated. One type of control algorithm for dual- speed operation is proposed. Results from a dynamic simulation will be presented to show how the control algorithm works and how power, current and torque of the system vary as the wind turbine is exposed to varying wind speeds.

Muljadi, E.; Butterfield, C.P.

1996-10-01T23:59:59.000Z

276

Application of a Sequential Reaction Model to PANS and Aldehyde Measurements in Two Urban Areas  

SciTech Connect

Measurements of peroxycarboxylic nitric anhydrides (= PAN, PPN, MPAN) and aldehydes (acetaldehyde, propanal, and methacrolein) were made at Nashville, Tennessee, in 1999 and Houston, Texas, in 2000. The data were interpreted with a sequential reaction model that included reaction of aldehydes with hydroxl radical and formation or loss of PANs mediated by peroxyacyl radicals. The comparison of the measured ratios with those predicted by the model showed disagreement for PAN/acetaldehyde and PPN/propanal in Nashville but agreement in Houston. These features are consistent with the relative importance of isoprene to PAN formation at each site.

Roberts, James M.; Stroud, C.; Jobson, B Tom T.; Trainer, Michael; Hereid, D.; Williams, E. J.; Fehsenfeld, Fred C.; Brune, W. H.; Martinez, M.; Harder, H.

2001-12-15T23:59:59.000Z

277

Sequential Monte Carlo simulation for composite power system reliability analysis with time varying loads  

SciTech Connect

The paper illustrates the development and utilization of an annual chronological load curve for each load bus in a composite generation and transmission system and a sequential Monte Carlo simulation approach for composite system reliability assessment. Antithetic variates as a variance reduction technique has been applied to the simulation model to increase the efficiency of the simulation. An approximate method using a load duration curve of the system load and an enumeration process have been applied to the developed load model and the results are compared in this paper.

Sankarakrishnan, A.; Billinton, R. [Univ. of Saskatchewan, Saskatoon, Saskatchewan (Canada). Power Systems Research Group

1995-08-01T23:59:59.000Z

278

Sequential Window Diagnoser for Discrete-Event Systems Under Unreliable Observations  

SciTech Connect

This paper addresses the issue of counting the occurrence of special events in the framework of partiallyobserved discrete-event dynamical systems (DEDS). Developed diagnosers referred to as sequential window diagnosers (SWDs) utilize the stochastic diagnoser probability transition matrices developed in [9] along with a resetting mechanism that allows on-line monitoring of special event occurrences. To illustrate their performance, the SWDs are applied to detect and count the occurrence of special events in a particular DEDS. Results show that SWDs are able to accurately track the number of times special events occur.

Wen-Chiao Lin; Humberto E. Garcia; David Thorsley; Tae-Sic Yoo

2009-09-01T23:59:59.000Z

279

Enhanced Sequential Search Methodology for Identifying Cost-Optimal Building Pathways  

SciTech Connect

The BEopt software is a building energy optimization tool that generates a cost-optimal path of building designs from a reference building up to zero-net energy. It employs a sequential search methodology to account for complex energy interactions between building efficiency measures. Enhancement strategies to this search methodology are developed to increase accuracy (ability to identify the true cost-optimal curve) and speed (number of required energy simulations). A test suite of optimizations is used to gauge the effectiveness of each strategy. Combinations of strategies are assembled into packages, ranging from conservative to aggressive, with so up to 71% fewer required simulations are required.

Horowitz, S.; Christensen, C.; Brandemuehl, M.; Krarti, M.

2008-06-01T23:59:59.000Z

280

Advanced turbine systems program  

SciTech Connect

In accordance with the goals of the DOE program, improvements in the gas turbine are the primary focus of Allison activity during Phase I. To this end Allison conducted a survey of potentially applicable gas turbine cycles and selected the advanced combined cycle as reference system. Extensive analysis of two versions of the advanced combined cycle was performed against the requirement for a 60% thermal efficiency (LHV) utility-sized, natural gas fired system. This analysis resulted in technology requirements for this system. Additional analysis determined emissions potential for the system, established a coal-fueled derivative system and a commercialization plan. This report deals with the technical requirements for a system that meets the thermal efficiency goal. Allison initially investigated four basic thermodynamic cycles: Humid air turbine, intercalate-recuperated systems, advanced combined cycle, chemically recuperated cycle. Our survey and cycle analysis indicated that au had the potential of reaching 60% thermal efficiency. We also concluded that engine hot section technology would be a critical technology regardless of which cycle was chosen. Based on this result Allison chose to concentrate on the advanced combined cycle. This cycle is well known and understood by the utility turbine user community and is therefore likely to be acceptable to users.

Wilkes, C.; Mukavetz, D.W.; Knickerbocker, T.K.; Ali, S.A.

1992-12-31T23:59:59.000Z

Note: This page contains sample records for the topic "advanced sequential dual" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


281

Advanced turbine systems program  

SciTech Connect

In accordance with the goals of the DOE program, improvements in the gas turbine are the primary focus of Allison activity during Phase I. To this end Allison conducted a survey of potentially applicable gas turbine cycles and selected the advanced combined cycle as reference system. Extensive analysis of two versions of the advanced combined cycle was performed against the requirement for a 60% thermal efficiency (LHV) utility-sized, natural gas fired system. This analysis resulted in technology requirements for this system. Additional analysis determined emissions potential for the system, established a coal-fueled derivative system and a commercialization plan. This report deals with the technical requirements for a system that meets the thermal efficiency goal. Allison initially investigated four basic thermodynamic cycles: Humid air turbine, intercalate-recuperated systems, advanced combined cycle, chemically recuperated cycle. Our survey and cycle analysis indicated that au had the potential of reaching 60% thermal efficiency. We also concluded that engine hot section technology would be a critical technology regardless of which cycle was chosen. Based on this result Allison chose to concentrate on the advanced combined cycle. This cycle is well known and understood by the utility turbine user community and is therefore likely to be acceptable to users.

Wilkes, C.; Mukavetz, D.W.; Knickerbocker, T.K.; Ali, S.A.

1992-01-01T23:59:59.000Z

282

Advanced fossil energy utilization  

Science Conference Proceedings (OSTI)

This special issue of Fuel is a selection of papers presented at the symposium Advanced Fossil Energy Utilization co-sponsored by the Fuels and Petrochemicals Division and Research and New Technology Committee in the 2009 American Institute of Chemical Engineers (AIChE) Spring National Meeting Tampa, FL, on April 2630, 2009.

Shekhawat, D.; Berry, D.; Spivey, J.; Pennline, H.; Granite, E.

2010-01-01T23:59:59.000Z

283

ROCKY MOUNTAIN OILFIELD TESTING CENTER Texaco Dual Action Pumping System  

NLE Websites -- All DOE Office Websites (Extended Search)

Texaco Dual Action Pumping System Texaco Dual Action Pumping System PROJECT TEST RESULTS March 16, 1998 Michael R. Tyler Project Manager Abstract The Texaco Dual Action Pumping System (DAPS) is designed to separate water from the oil in the casing-tubing annulas and inject most of the water into a lower formation while lifting the oil and remaining water to the surface. As oil production declines in a well the water production can increase. The lifting cost can be reduced per barrel of oil if less water is brought to the surface and processed. The DAPS was installed in a well that had been producing four (4) barrels of oil per day (bopd) and 46 barrels of water per day (bwpd), from the zone that became the injection zone. The well was recompleted in a shallower zone that was expected to yield an excessive quantity of

284

Dual-environment effects on the oxidation of metallic interconnects  

DOE Green Energy (OSTI)

Metallic interconnects in solid oxide fuel cells are exposed to a dual environment: fuel on one side (i.e., H2 gas) and oxidizer on the other side (i.e., air). It has been observed that the oxidation behavior of thin stainless steel sheet in air is changed by the presence of H2 on the other side of the sheet. The resulting dual-environment scales are flaky and more friable than the single-environment scales. The H2 disrupts the scale on the air side. A model to explain some of the effects of a dual environment is presented where hydrogen diffusing through the stainless steel sheet reacts with oxygen diffusing through the scale to form water vapor, which has sufficient vapor pressure to mechanically disrupt the scale. Experiments on preoxidized 316L stainless steel tubing exposed to air-air, H2-air, and H2-Ar environments are reported in support of the model.

Holcomb, G.R.; Ziomek-Moroz, M.; Covino, B.S., Jr.; Bullard, S.J.

2006-08-01T23:59:59.000Z

285

Approval Process for Dual Compensation Waivers for Reemployed Annuitants  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

10 10 MEMORANDUM FOR HUMAN RESOURCE DIRECTORS ~~~ - FROM: SARAH J. NILLA, DIRECTOR OFFICE 0 UMAN CAPITAL MANAGEMENT SUBJECT: POLICY MEMORANDUM # 11: APPROVAL PROCESS FOR DUAL COMPENSATION WAIVERS FOR REEMPLOYED ANNUITANTS Section 1122 of the National Defense Authorization Act for Fiscal Year 2010, Public Law 111-84 (Pub. L 111-84) allows the head of an agency to grant dual compensation (salary-offset) waivers to reemployed annuitants who work on a limited basis without reduction to their retirement annuity. This provision in the law expires October 27, 2014. Secretary Chu has delegated the authority to approve all dual compensation waiver requests to the Department's Chief Human Capital Officer (CHCO). This authority can be used to: a) Fulfill functions critical to the mission of the agency (or any subcomponent of

286

Dual-Fuel Truck Fleet: Start-Up Experience  

DOE Green Energy (OSTI)

Although dual-fuel engine technology has been in development and limited use for several years, it has only recently moved toward full-scale operational capability for heavy-duty truck applications. Unlike a bifuel engine, which has two separate fuel systems that are used one at a time, a dual-fuel engine uses two fuel systems simultaneously. One of California's South Coast Air Quality Management District (SCAQMD) current programs is a demonstration of dual-fuel engine technology in heavy-duty trucks. These trucks are being studied as part of the National Renewable Energy Laboratory's (NREL's) Alternative Fuel Truck Program. This report describes the start-up experience from the program.

NREL

1998-09-30T23:59:59.000Z

287

Mode Competition in Dual-Mode Quantum Dots Semiconductor Microlaser  

E-Print Network (OSTI)

This paper describes the modeling of quantum dots lasers with the aim of assessing the conditions for stable cw dual-mode operation when the mode separation lies in the THz range. Several possible models suited for InAs quantum dots in InP barriers are analytically evaluated, in particular quantum dots electrically coupled through a direct exchange of excitation by the wetting layer or quantum dots optically coupled through the homogeneous broadening of their optical gain. A stable dual-mode regime is shown possible in all cases when quantum dots are used as active layer whereas a gain medium of quantum well or bulk type inevitably leads to bistable behavior. The choice of a quantum dots gain medium perfectly matched the production of dual-mode lasers devoted to THz generation by photomixing.

Chusseau, Laurent; Viktorovitch, P; Letartre, Xavier

2013-01-01T23:59:59.000Z

288

Development of PC 4 dual-fuel engine  

SciTech Connect

Recently, utilization of natural gas, which is considered to be one of most important alternative fuels for petroleum, has been marked. As thermal efficiency of dual-fuel engine is higher than those of other prime movers with gaseous fuel, i.e., spark-ignited gas engine or gas turbine, it is possible to construct fuel-economical gas power plants with dual-fuel engines. However, its horsepower has been limited to the rather lower range. In 1984, NKK succeeded in developing large-sized dual-fuel engines based on the Pielstick PC4 diesel engine. The horsepower is 1200 HP/cyl, i.e. 21,600 HP for 18-cyclinder engine.

Nishikawa, T.; Utsuyama, S.; Maruyama, S.; Ono, T.; Kitahara, S.

1985-01-01T23:59:59.000Z

289

Using dual decomposition for solving problems involving data uncertainty |  

NLE Websites -- All DOE Office Websites (Extended Search)

dual decomposition for solving problems involving data uncertainty dual decomposition for solving problems involving data uncertainty August 14, 2013 Tweet EmailPrint Many applications mdash; energy, routing, scheduling, and production planning, for example mdash; involve problems in which some or all of the data may not be known when decisions under uncertainty must be made. In such cases, approximations with stochastic mixed-integer programming models are often used. Two approaches have been suggested to address such problems: dual decomposition (DD) and branch-and-price (BP). Both approaches divide the problem into two or more subproblems, together with linear constraints that enforce agreement between solutions to the different problems through a series of iterations. Unfortunately, both approaches also suffer from lack

290

Advanced Coal Wind Hybrid: Economic Analysis  

E-Print Network (OSTI)

feasibility of combining wind farms with advanced coalfeasibility of combining wind farms with advanced coal

Phadke, Amol

2008-01-01T23:59:59.000Z

291

Evaluation of liquid lift approach to dual gradient drilling  

E-Print Network (OSTI)

In the past, the oil and gas industry has typically used the single gradient system to drill wells offshore. With this system the bottom hole pressure was controlled by a mud column extending from the drilling rig to the bottom of the wellbore. This mud column was used to achieve the required bottom hole pressure. But, as the demand for oil and gas increased, the industry started exploring for oil and gas in deep waters. Because of the narrow margin between the pore and fracture pressures it is somewhat difficult to reach total depth with the single gradient system. This led to the invention of the dual gradient system. In the dual gradient method, heavy density fluid runs from the bottom hole to the mudline and a low density fluid from the mudline to the rig floor so as to maintain the bottom hole pressure. Several methods have been developed to achieve the dual gradient drilling principle. For this research project, we paid more attention to the liquid lift, dual gradient drilling (riser dilution method). This method of achieving dual gradient drilling was somewhat different from the others, because it does not utilize elaborate equipment and no major changes are made on the existing drilling rigs. In this thesis the technical feasibility of using the liquid lift method over the other methods of achieving dual gradient drilling was determined. A computer program was developed to simulate the wellbore hydraulics under static and dynamic conditions, injection rate and base fluid density required to dilute the riser fluid and finally, u-tubing phenomena. In this thesis we also identified some problems associated with the liquid lift method and recommendations were made on how these problems can be eliminated or reduced. Emphases were placed on the effect of u-tubing, injection rate of base fluid at the bottom of the riser and well control issues facing this system.

Okafor, Ugochukwu Nnamdi

2007-12-01T23:59:59.000Z

292

Evaluation of liquid lift approach to dual gradient  

E-Print Network (OSTI)

In the past, the oil and gas industry has typically used the single gradient system to drill wells offshore. With this system the bottom hole pressure was controlled by a mud column extending from the drilling rig to the bottom of the wellbore. This mud column was used to achieve the required bottom hole pressure. But, as the demand for oil and gas increased, the industry started exploring for oil and gas in deep waters. Because of the narrow margin between the pore and fracture pressures it is somewhat difficult to reach total depth with the single gradient system. This led to the invention of the dual gradient system. In the dual gradient method, heavy density fluid runs from the bottom hole to the mudline and a low density fluid from the mudline to the rig floor so as to maintain the bottom hole pressure. Several methods have been developed to achieve the dual gradient drilling principle. For this research project, we paid more attention to the liquid lift, dual gradient drilling (riser dilution method). This method of achieving dual gradient drilling was somewhat different from the others, because it does not utilize elaborate equipment and no major changes are made on the existing drilling rigs. In this thesis the technical feasibility of using the liquid lift method over the other methods of achieving dual gradient drilling was determined. A computer program was developed to simulate the wellbore hydraulics under static and dynamic conditions, injection rate and base fluid density required to dilute the riser fluid and finally, u-tubing phenomena. In this thesis we also identified some problems associated with the liquid lift method and recommendations were made on how these problems can be eliminated or reduced. Emphases were placed on the effect of u-tubing, injection rate of base fluid at the bottom of the riser and well control issues facing this system.

Okafor, Ugochukwu Nnamdi

2007-12-01T23:59:59.000Z

293

Dual output acoustic wave sensor for molecular identification  

DOE Patents (OSTI)

A method of identification and quantification of absorbed chemical species by measuring changes in both the velocity and the attenuation of an acoustic wave traveling through a thin film into which the chemical species is sorbed. The dual output response provides two independent sensor responses from a single sensing device thereby providing twice as much information as a single output sensor. This dual output technique and analysis allows a single sensor to provide both the concentration and the identity of a chemical species or permits the number of sensors required for mixtures to be reduced by a factor of two.

Frye, Gregory C. (Cedar Crest, NM); Martin, Stephen J. (Albuquerque, NM)

1991-01-01T23:59:59.000Z

294

Advanced Vehicle Testing Activity: Overview  

NLE Websites -- All DOE Office Websites (Extended Search)

Overview to Overview to someone by E-mail Share Advanced Vehicle Testing Activity: Overview on Facebook Tweet about Advanced Vehicle Testing Activity: Overview on Twitter Bookmark Advanced Vehicle Testing Activity: Overview on Google Bookmark Advanced Vehicle Testing Activity: Overview on Delicious Rank Advanced Vehicle Testing Activity: Overview on Digg Find More places to share Advanced Vehicle Testing Activity: Overview on AddThis.com... Home Overview Light-Duty Vehicles Medium- and Heavy-Duty Vehicles Publications Overview The marketplace for advanced transportation technologies and the focus, direction, and funding of transportation programs are continually changing. The Advanced Vehicle Testing Activity's "2005 Overview of Advanced Technology Transportation" (PDF 736 KB) gives the latest information about

295

Transformation of Dual-Polarized Radar Measurements to Arbitrary Polarization Bases  

Science Conference Proceedings (OSTI)

A fully polarimetric radar system consists of an orthogonal dual-polarized transmission mode and a dual-channel receive mode that are typically set to be copolar and cross polar to the transmit state of polarization. The transmit polarization ...

V. Chandrasekar; J. Hubbert; V. N. Bringi; P. F. Meischner

1994-08-01T23:59:59.000Z

296

A GPM Dual-Frequency Retrieval Algorithm: DSD Profile-Optimization Method  

Science Conference Proceedings (OSTI)

A new dual-frequency precipitation radar (DPR) will be included on the Global Precipitation Measurement (GPM) core satellite, which will succeed the highly successful Tropical Rainfall Measuring Mission (TRMM) satellite launched in 1997. New dual-...

C. R. Rose; V. Chandrasekar

2006-10-01T23:59:59.000Z

297

An Early Performance Evaluation of the NEXRAD Dual Polarization Radar Rainfall Estimates for Urban Flood Applications  

Science Conference Proceedings (OSTI)

Dual polarization radars are expected to provide better rainfall estimates than single polarization radars due to their ability to characterize hydrometeor type. The goal of this study is to evaluate single and dual polarization radar rainfall ...

Luciana K. Cunha; James A. Smith; Mary Lynn Baeck; Witold F. Krajewski

298

A Dual-Wavelength Radar Method for Ice-Water Characterization in Mixed-Phase Clouds  

Science Conference Proceedings (OSTI)

A dual-wavelength method to differentiate supercooled water from ice and to measure mass content in each phase in cold stratiform clouds is proposed and discussed. The differential attenuation Ad, whose direct measurement is available with dual-...

Marielle Gosset; Henri Sauvageot

1992-10-01T23:59:59.000Z

299

Potential Role Of Dual- Polarization Radar In The Validation Of Satellite Precipitation Measurements: Rationale and Opportunities  

Science Conference Proceedings (OSTI)

Dual-polarization weather radars have evolved significantly in the last three decades culminating in operational deployment by the National Weather Service. In addition to operational applications in the weather service, dual-polarization radars ...

V. Chandrasekar; V. N. Bringi; S. A. Rutledge; Arthur Hou; Eric Smith; Gail Skofronick Jackson; E. Gorgucci; W. A. Petersen

2008-08-01T23:59:59.000Z

300

Effects of Drop-Size-Distribution Truncation on Computer Simulations of Dual-Measurement Radar Methods  

Science Conference Proceedings (OSTI)

An investigation is made of the effects of truncating the raindrop-size distribution at minimum and maximum diameters on the results of computer simulations of dual-measurement radar methods. The dual-measurement methods investigated include ...

Carlton W. Ulbrich

1992-07-01T23:59:59.000Z

Note: This page contains sample records for the topic "advanced sequential dual" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


301

Incorporation of scattered radiation into dual?energy radiologic theory and application to mammography  

Science Conference Proceedings (OSTI)

A previous analysis of dual?energy imaging is extended to incorporate scattered radiation. The analysis is general and can include polyenergetic beams and nonideal detectors. In the dual?material basis plane

Paul C. Johns

1994-01-01T23:59:59.000Z

302

35-GHz Dual-Polarization Propagation Link for Rain-Rate Estimation  

Science Conference Proceedings (OSTI)

A 35-GHz dual-polarization propagation link (DPPL) is described and initial measurements are presented. The instrument is essentially a small, low-power, portable, dual linearly polarized pulsed radar that provides differential attenuation ...

Christopher S. Ruf; Kultegin Aydin; Savyasachee Mathur; Justin P. Bobak

1996-04-01T23:59:59.000Z

303

STRUCTURAL ANALYSES OF FUEL CASKS SUBJECTED TO BOLT PRELOAD, INTERNAL PRESSURE AND SEQUENTIAL DYNAMIC IMPACTS  

Science Conference Proceedings (OSTI)

Large fuel casks subjected to the combined loads of closure bolt tightening, internal pressure and sequential dynamic impacts present challenges when evaluating their performance in the Hypothetical Accident Conditions (HAC) specified in the Code of Federal Regulations Title 10 Part 71 (10CFR71). Testing is often limited by cost, difficulty in preparing test units and the limited availability of facilities which can carry out such tests. In the past, many casks were evaluated without testing by using simplified analytical methods. In addition, there are no realistic analyses of closure bolt stresses for HAC conditions reported in the open literature. This paper presents a numerical technique for analyzing the accumulated damages of a large fuel cask caused by the sequential loads of the closure bolt tightening and the internal pressure as well as the drop and crash dynamic loads. The bolt preload and the internal pressure are treated as quasi-static loads so that the finite element method with explicit numerical integration scheme based on the theory of wave propagation can be applied. The dynamic impacts with short durations such as the 30-foot drop and the 40-inch puncture for the hypothetical accident conditions specified in 10CFR71 are also analyzed by using the finite-element method with explicit numerical integration scheme.

Wu, T

2009-06-25T23:59:59.000Z

304

Sequential high temperature reduction, low temperature hydrolysis for the regeneration of sulfated NOx trap catalysts  

SciTech Connect

We describe a new method that minimizes irreversible Pt sintering during the desulfation of sulfated Pt/BaO/Al2O3 lean NOx trap (LNT) catalysts. While it is known that the addition of H2O to H2 promotes desulfation, we find that the significant and irreversible Pt sintering arising from the presence of water is unavoidable. Control of precious metal sintering is considered to be one of the critical issues in the development of durable LNT catalysts. The new method described here is a sequential desulfation process: the first step is to reduce the sulfates with hydrogen only at higher temperatures to form BaS, followed by a treatment of the thus reduced sample with water at low to moderate temperatures to convert BaS to BaO and H2S. The data showed that Pt sintering was significantly inhibited due to the absence of H2O during the desulfation at high temperatures, and also demonstrates the similar NOx uptake with the desulfated sample cooperatively with H2 and H2O. Therefore, the sequential desulfation process may find applications in realistic systems to inhibit the irreversible sintering of the Pt in the lean NOx trap catalyst, leading to a longer catalyst life.

Kim, Do Heui; Kwak, Ja Hun; Wang, Xianqin; Szanyi, Janos; Peden, Charles HF

2008-07-15T23:59:59.000Z

305

TESTING OF THE DUAL ROTARY FILTER SYSTEM  

SciTech Connect

The Savannah River National Laboratory (SRNL) installed and tested two hydraulically connected SpinTek rotary microfilter (RMF) units to determine the behavior of a multiple filter system. Both units were successfully controlled by a control scheme written in DELTA-V architecture by Savannah River Remediation (SRR) Process Control Engineering personnel. The control system was tuned to provide satisfactory response to changing conditions during the operation of the multi-filter system. Stability was maintained through the startup and shutdown of one of the filter units while the second was still in operation. The installation configuration originally proposed by the Small Colum Ion Exchange (SCIX) project of independent filter and motor mountings may be susceptible to vibration. Significant stiffening of the filter and motor mounts was required to minimize the vibration. Alignment of the motor to the filter was a challenge in this test configuration. The deployment configuration must be easy to manipulate and allow for fine adjustment. An analysis of the vibration signature of the test system identified critical speeds. Whether it corresponds to the resonance frequency of a rotor radial vibration mode that was excited by rotor unbalance is uncertain based upon the measurements. A relative motion series should be completed on the filter with the final shaft configuration to determine if the resonances exist in the final filter design. The instrumentation selected for deployment, including the concentrate discharge control valve and flow meters, performed well. Automation of the valve control integrated well with the control scheme and when used in concert with the other control variables, allowed automated control of the dual RMF system. The one area of concern with the instrumentation was the condition resulting when the filtrate flow meter operated with less than three gpm. This low flow was at the lower range of performance for the flow meter. This should not be an issue in deployment where the desired flow rate will be within the normal operating range of the meter. Testing demonstrated that the use of a flexible line for the filtrate discharge is highly desired at the outlet of the rotary union to transition to the system piping. Isolating the vibration from the rotary union will significantly improve the lifetime of the seals. Methods to monitor and isolate individual filters should be considered during deployment. The ability to diagnose issues and isolate individual filters would allow isolation prior to failure. Thus, filters may be cleaned or repaired instead of requiring complete replacement if the condition were to continue unnoticed. Isolating the filtrate line of each filter during startup will minimize the premature buildup of solids on the filter disks. Several tests have shown that the method of filter startup can improve performance lifetime of the filters. The installation must factor in an air inlet for the draining of a filter that does not involve a reverse flow through the filter disks. The reverse flow may cause deformation of the disks or may damage other components of the filters themselves.

Herman, D.; Fowley, M.; Stefanko, D.

2011-08-29T23:59:59.000Z

306

Posters | Advanced Photon Source  

NLE Websites -- All DOE Office Websites (Extended Search)

Your Cart (0 Posters) Your Cart (0 Posters) Your cart is empty. checkout Subtotal: $0.00 update empty Posters Order a printed APS poster! 11 in. x 17 in. prints will be mailed in the order requests are received. 36 in. x 36 in. posters will be sent to school addresses once all orders are processed. The Advanced Photon Source Is The Advanced Photon Source Is Qty: 1 add to cart Technologies from Materials Science Technologies from Materials Science Qty: 1 add to cart Materials Under Extreme Pressure Materials Under Extreme Pressure Qty: 1 add to cart Biological Macromolecules in Action Biological Macromolecules in Action Qty: 1 add to cart Journey to the Center of the Earth Journey to the Center of the Earth Qty: 1 add to cart Earthshaking Monitor Earthshaking Monitor Qty: 1 add to cart Imaging with X-rays

307

Advanced Simulation Capability for  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Simulation Capability for Simulation Capability for Environmental Management (ASCEM) ASCEM is being developed to provide a tool and approach to facilitate robust and standardized development of perfor- mance and risk assessments for cleanup and closure activi- ties throughout the EM complex. The ASCEM team is composed of scientists from eight National Laboratories. This team is leveraging Department of Energy (DOE) investments in basic science and applied research including high performance computing codes developed through the Advanced Scientific Computing Research and Advanced Simulation & Computing pro- grams as well as collaborating with the Offices of Science, Fossil Energy, and Nuclear Energy. Challenge Current groundwater and soil remediation challenges that will continue to be addressed in the next decade include

308

Overview | Advanced Photon Source  

NLE Websites -- All DOE Office Websites (Extended Search)

APS Overview: APS Overview: Introduction APS Systems Map LINAC Booster Synchrotron Storage Ring Insertion Devices Experiment Hall LOMs & Beamlines Overview of the APS The Advanced Photon Source (APS) at the U.S. Department of Energy's Argonne National Laboratory provides this nation's (in fact, this hemisphere's) brightest storage ring-generated x-ray beams for research in almost all scientific disciplines. Photo: Aerial Photo of APS Aerial photo of the Advanced Photon Source These x-rays allow scientists to pursue new knowledge about the structure and function of materials in the center of the Earth and in outer space, and all points in between. The knowledge gained from this research can impact the evolution of combustion engines and microcircuits, aid in the development of new pharmaceuticals, and pioneer nanotechnologies whose

309

NETL: Advanced Research - Ultrasupercritical  

NLE Websites -- All DOE Office Websites (Extended Search)

High Performance Materials > Ultrasupercritical High Performance Materials > Ultrasupercritical Advanced Research High Performance Materials Ultrasupercritical Increasing the temperature and pressure of steam improves the efficiency of boilers and turbines that use steam as the working fluid. These higher efficiency boilers and turbines require less coal and produce less greenhouse gases. Identifying materials that can operate for long periods of time at extreme temperatures and pressures is a major goal of NETL's Advanced Research Materials Program. Phase diagram of water Figure 1: Phase diagram of water To understand the terminology of boilers and turbines, it is first necessary to understand the basics of the water/steam phase diagram (see Figure 1). The normal boiling point (nbp) of water occurs at 1 atmosphere

310

Advanced Photon Source  

NLE Websites -- All DOE Office Websites (Extended Search)

Tomography Interest Group Contact: Robert Winarski, Center for Nanoscale Materials winarski@anl.gov Contact: Francesco De Carlo, Advanced Photon Source decarlo@aps.anl.gov The tomography special interest group of the Advanced Photon Source (APS) at Argonne National Laboratory has been created to promote awareness of the tomography facilities at the APS and to foster communications between the various research groups. Through this group, we believe we can build a strong user community for tomography. The following beamlines have active tomography research programs: 2-BM-B (XOR) http://www.aps.anl.gov/Xray_Science_Division/Xray_Microscopy_and_Imaging/Science_and_Research/Techniques/Tomography/index.html Information about the beamline: http://beam.aps.anl.gov/pls/apsweb/beamline_display_pkg.display_beamline?p_beamline_num_c=31

311

Advanced Technology Vehicle Testing  

DOE Green Energy (OSTI)

The goal of the U.S. Department of Energy's Advanced Vehicle Testing Activity (AVTA) is to increase the body of knowledge as well as the awareness and acceptance of electric drive and other advanced technology vehicles (ATV). The AVTA accomplishes this goal by testing ATVs on test tracks and dynamometers (Baseline Performance testing), as well as in real-world applications (Fleet and Accelerated Reliability testing and public demonstrations). This enables the AVTA to provide Federal and private fleet managers, as well as other potential ATV users, with accurate and unbiased information on vehicle performance and infrastructure needs so they can make informed decisions about acquiring and operating ATVs. The ATVs currently in testing include vehicles that burn gaseous hydrogen (H2) fuel and hydrogen/CNG (H/CNG) blended fuels in internal combustion engines (ICE), and hybrid electric (HEV), urban electric, and neighborhood electric vehicles. The AVTA is part of DOE's FreedomCAR and Vehicle Technologies Program.

James Francfort

2004-06-01T23:59:59.000Z

312

Advanced drilling systems  

DOE Green Energy (OSTI)

Drilling is ubiquitous in oil, gas, geothermal, minerals, water well, and mining industries. Drilling and well completion account for 25% to 50% of the cost of producing power from geothermal energy. Reduced drilling costs will reduce the cost of electricity produced from geothermal resources. Undoubtedly, there are concepts for advanced drilling systems that have yet to be studied. However, the breadth and depth of previous efforts in this area almost guarantee that any new efforts will at least initially build on an idea or a variation of an idea that has already been investigated. Therefore, a review of previous efforts, coupled with a characterization of viable advanced drilling systems and the current state of technology as it applies to those systems, provide the basis for this study.

Pierce, K.G.; Finger, J.T. [Sandia National Labs., Albuquerque, NM (United States); Livesay, B.J. [Livesay Consultants, San Diego, CA (United States)

1995-12-31T23:59:59.000Z

313

Advanced far infrared detectors  

SciTech Connect

Recent advances in photoconductive and bolometric semiconductor detectors for wavelength 1 mm > {lambda} > 50 {mu}m are reviewed. Progress in detector performance in this photon energy range has been stimulated by new and stringent requirements for ground based, high altitude and space-borne telescopes for astronomical and astrophysical observations. The paper consists of chapters dealing with the various types of detectors: Be and Ga doped Ge photoconductors, stressed Ge:Ga devices and neutron transmutation doped Ge thermistors. Advances in the understanding of basic detector physics and the introduction of modern semiconductor device technology have led to predictable and reliable fabrication techniques. Integration of detectors into functional arrays has become feasible and is vigorously pursued by groups worldwide.

Haller, E.E.

1993-05-01T23:59:59.000Z

314

Advanced Separation Consortium  

Science Conference Proceedings (OSTI)

The Center for Advanced Separation Technologies (CAST) was formed in 2001 under the sponsorship of the US Department of Energy to conduct fundamental research in advanced separation and to develop technologies that can be used to produce coal and minerals in an efficient and environmentally acceptable manner. The CAST consortium consists of seven universities - Virginia Tech, West Virginia University, University of Kentucky, Montana Tech, University of Utah, University of Nevada-Reno, and New Mexico Tech. The consortium brings together a broad range of expertise to solve problems facing the US coal industry and the mining sector in general. At present, a total of 60 research projects are under way. The article outlines some of these, on topics including innovative dewatering technologies, removal of mercury and other impurities, and modelling of the flotation process. 1 photo.

NONE

2006-01-01T23:59:59.000Z

315

Advanced Photon Source  

NLE Websites -- All DOE Office Websites (Extended Search)

0 Advanced Photon Source 0 Advanced Photon Source A U.S. Department of Energy, Office of Science, Office of Basic Energy Sciences national synchrotron x-ray research facility Search Button About Welcome Overview Visiting the APS Mission & Goals Find People Organization Charts Committees Job Openings User Information Prospective Users New Users Current Users APS User Portal Macromolecular Crystallographers Administrators Find a Beamline Apply for Beam Time Contacts Calendars Community Scientific Access Site Access Training Science & Education Science & Research Highlights Conferences Seminars Publications Annual Reports APS Upgrade Courses and Schools Graduate Programs Scientific Software Media Center Calendar of Events APS News User News Argonne/APS Press Releases Argonne/APS Feature Stories Argonne/APS In The News

316

Advanced Energy Guides  

NLE Websites -- All DOE Office Websites (Extended Search)

Energy Guides Energy Guides Shanti Pless National Renewable Energy Laboratory shanti.pless@nrel.gov 303-384-6365 April 4 2013 2 | Building Technologies Office eere.energy.gov Advanced Energy Design Guides Provide prescriptive energy savings guidance and recommendations by building type and geographic location: * Design packages and strategies to help owners and designers achieve 50% site energy savings over Standard 90.1 * Two series: - 30% savings over 90.1-1999

317

Advanced geothermal technologies  

DOE Green Energy (OSTI)

Research and development in advanced technologies for geothermal energy production continue to increase the energy production options for the Nation. The high-risk investment over the past few years by the US Department of Energy in geopressured, hot dry rock, and magma energy resources is producing new means to lower production costs and to take advantage of these resources. The Nation has far larger and more regionally extensive geothermal resources than heretofore realized. At the end of a short 30-day closed-loop flow test, the manmade hot dry rock reservoir at Fenton Hill, New Mexico, was producing 10 MW thermal - and still climbing - proving the technical feasibility of this new technology. The scientific feasibility of magma energy extraction has been demonstrated, and new field tests to evaluate this technology are planned. Analysis and field tests confirm the viability of geopressured-geothermal energy and the prospect that many dry-hole or depleted petroleum wells can be turned into producing geopressured-geothermal wells. Technological advances achieved through hot dry rock, magma, geopressured, and other geothermal research are making these resources and conventional hydrothermal resources more competitive. Noteworthy among these technological advances are techniques in computer simulation of geothermal reservoirs, new means for well stimulation, new high-temperature logging tools and packers, new hard-rock penetration techniques, and new methods for mapping fracture flow paths across large underground areas in reservoirs. In addition, many of these same technological advances can be applied by the petroleum industry to help lower production costs in domestic oil and gas fields. 5 refs., 4 figs.

Whetten, J.T.; Murphy, H.D.; Hanold, R.J.; Myers, C.W.; Dunn, J.C.

1988-01-01T23:59:59.000Z

318

Advanced Energy Guides  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Energy Guides Energy Guides Shanti Pless National Renewable Energy Laboratory shanti.pless@nrel.gov 303-384-6365 April 4 2013 2 | Building Technologies Office eere.energy.gov Advanced Energy Design Guides Provide prescriptive energy savings guidance and recommendations by building type and geographic location: * Design packages and strategies to help owners and designers achieve 50% site energy savings over Standard 90.1 * Two series: - 30% savings over 90.1-1999

319

Advanced Metering Infrastructure Technology  

Science Conference Proceedings (OSTI)

Revenue security is a major concern for utilities. Theft of electric service in the United States is widespread. In 2006, the revenue estimate for non-technical losses was 6.5 billion. Non-technical losses are associated with unidentified and uncollected revenue from pilferage, tampering with meters, defective meters, and errors in meter reading. In this report, revenue security describes the use of advanced metering infrastructure (AMI) technology to minimize non-technical losses.

2008-12-08T23:59:59.000Z

320

Advanced Turbine Design Program  

SciTech Connect

The prime objective of this project task is to select a natural gas fired as Advanced Turbine Systems (ATS) capable of reaching 60% cycle efficiency. Several cycles were compared and evaluated under all different kind of aspects, to determine the one with the highest potential and, at the same time, the best overall fit within and experience base to guarantee project goals. The combined cycle with multistep development potential was identified as the system to reach the 60% or greater thermal efficiency.

van der Linden, S.; Gnaedig, G.; Kreitmeier, F.

1992-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "advanced sequential dual" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


321

Advanced Turbine Design Program  

SciTech Connect

The prime objective of this project task is to select a natural gas fired as Advanced Turbine Systems (ATS) capable of reaching 60% cycle efficiency. Several cycles were compared and evaluated under all different kind of aspects, to determine the one with the highest potential and, at the same time, the best overall fit within and experience base to guarantee project goals. The combined cycle with multistep development potential was identified as the system to reach the 60% or greater thermal efficiency.

van der Linden, S.; Gnaedig, G.; Kreitmeier, F.

1992-12-31T23:59:59.000Z

322

Advanced Manufacturing Partnership  

Energy.gov (U.S. Department of Energy (DOE))

AMO leads DOE's participation in the national interagency Advanced Manufacturing Partnership (AMP). AMO joins with other Federal agencies investing in innovation and cost-shared R&D projects, supporting manufacturing infrastructure, and facilitating job creation. These actions save energy and provide benefits to U.S. industry and the national economy. AMO contributes more broadly to the AMP with activities in Technology Development, Shared Infrastructure and Facilities, Education and Workforce Development.

323

Advanced Polymer Processing Facility  

Science Conference Proceedings (OSTI)

Some conclusions of this presentation are: (1) Radiation-assisted nanotechnology applications will continue to grow; (2) The APPF will provide a unique focus for radiolytic processing of nanomaterials in support of DOE-DP, other DOE and advanced manufacturing initiatives; (3) {gamma}, X-ray, e-beam and ion beam processing will increasingly be applied for 'green' manufacturing of nanomaterials and nanocomposites; and (4) Biomedical science and engineering may ultimately be the biggest application area for radiation-assisted nanotechnology development.

Muenchausen, Ross E. [Los Alamos National Laboratory

2012-07-25T23:59:59.000Z

324

Advanced Lighting Technologies  

Science Conference Proceedings (OSTI)

This report continues the technical assessment of advanced lighting technologies in the following product areasdimmable light-emitting diode (LED) screw-in replacement lamp, hybrid compact fluorescent lamp/halogen screw-in replacement lamp, replacement recessed can LED downlight, organic LED (OLED) disc, replacement mini high-intensity discharge (HID) lamp and ballast system, and solid-state plasma lighting (miniature HID technology) high-bay fixture. The research in this project helps to demonstrate how...

2011-12-21T23:59:59.000Z

325

Achieving maximum spatial diversity with decouple-and-forward relaying in dual-hop OSTBC transmissions  

Science Conference Proceedings (OSTI)

In this letter, we prove that decouple-and-forward (DCF) relaying for dual-hop orthogonal space-time block code (OSTBC) transmissions achieves the maximum diversity order attainable by dual-hop MIMO relaying systems. Decoupling at the relay transforms ... Keywords: OSTBC, decouple-and-forward relaying, diversity order, dual-hop MIMO system, rayleigh fading channels

In-Ho Lee; Dongwoo Kim

2010-03-01T23:59:59.000Z

326

An Interleaved Dual-Battery Power Supply for Battery-Operated Electronics  

E-Print Network (OSTI)

An Interleaved Dual-Battery Power Supply for Battery-Operated Electronics QingQing Wu,Wu, Qinru VoltageAnalysis of Optimal Supply Voltage Design of Interleaved DualDesign of Interleaved Dual--Battery PowerBattery Power SupplySupply ConclusionsConclusions #12;Batteries in Mobile/Portable ElectronicsBatteries

Pedram, Massoud

327

Piecewise structural diffusion defined on shape index for noise reduction in dual-energy CT images  

Science Conference Proceedings (OSTI)

The increasing radiation dose in dual-energy CT (DE-CT) scanning due to the double exposures at 80 kVp and 140 kVp is a major concern in the application of DE-CT. This paper presents a novel image-space denoising method, called piecewise structural ... Keywords: dual-energy CT, dual-energy CT colonography, noise reduction

Wenli Cai; June-Goo Lee; Da Zhang; Christina Piel; Hiroyuki Yoshida

2012-10-01T23:59:59.000Z

328

Dual variational principle for a problem of heat conduction in a rectangular plate  

Science Conference Proceedings (OSTI)

In this paper we formulate the dual variational principle for a problem of heat conduction in a rectangular domain, represented by elliptic equation with boundary conditions (Dirichlet-Neumann). The approximate solution for the dual variational problem ... Keywords: dual functional, heat transfer, weak solution

Mioara Boncu?; Dumitru Barac

2010-07-01T23:59:59.000Z

329

Advanced Technology Vehicle Testing  

DOE Green Energy (OSTI)

The light-duty vehicle transportation sector in the United States depends heavily on imported petroleum as a transportation fuel. The Department of Energys Advanced Vehicle Testing Activity (AVTA) is testing advanced technology vehicles to help reduce this dependency, which would contribute to the economic stability and homeland security of the United States. These advanced technology test vehicles include internal combustion engine vehicles operating on 100% hydrogen (H2) and H2CNG (compressed natural gas) blended fuels, hybrid electric vehicles, neighborhood electric vehicles, urban electric vehicles, and electric ground support vehicles. The AVTA tests and evaluates these vehicles with closed track and dynamometer testing methods (baseline performance testing) and accelerated reliability testing methods (accumulating lifecycle vehicle miles and operational knowledge within 1 to 1.5 years), and in normal fleet environments. The Arizona Public Service Alternative Fuel Pilot Plant and H2-fueled vehicles are demonstrating the feasibility of using H2 as a transportation fuel. Hybrid, neighborhood, and urban electric test vehicles are demonstrating successful applications of electric drive vehicles in various fleet missions. The AVTA is also developing electric ground support equipment (GSE) test procedures, and GSE testing will start during the fall of 2003. All of these activities are intended to support U.S. energy independence. The Idaho National Engineering and Environmental Laboratory manages these activities for the AVTA.

James Francfort

2003-11-01T23:59:59.000Z

330

Advanced Microturbine Systems  

SciTech Connect

Dept. of Energy (DOE) Cooperative Agreement DE-FC02-00-CH11061 was originally awarded to Honeywell International, Inc. ?? Honeywell Power Systems Inc. (HPSI) division located in Albuquerque, NM in October 2000 to conduct a program titled Advanced Microturbine Systems (AMS). The DOE Advanced Microturbines Systems Program was originally proposed as a five-year program to design and develop a high efficiency, low emissions, durable microturbine system. The period of performance was to be October 2000 through September 2005. Program efforts were underway, when one year into the program Honeywell sold the intellectual property of Honeywell Power Systems Inc. and HPSI ceased business operations. Honeywell made an internal decision to restructure the existing program due to the HPSI shutdown and submitted a formal request to DOE on September 24, 2001 to transfer the Cooperative Agreement to Honeywell Engines, Systems and Services (HES&S) in Phoenix, AZ in order to continue to offer support for DOE's Advanced Microturbine Program. Work continued on the descoped program under Cooperative Agreement No. DE-FC26-00-CH11061 and has been completed.

None

2005-12-31T23:59:59.000Z

331

Advancement of Electrochromic Windows  

NLE Websites -- All DOE Office Websites (Extended Search)

Advancement of Electrochromic Windows Advancement of Electrochromic Windows Title Advancement of Electrochromic Windows Publication Type Report LBNL Report Number LBNL-59821 Year of Publication 2006 Authors Lee, Eleanor S., Stephen E. Selkowitz, Robert D. Clear, Dennis L. DiBartolomeo, Joseph H. Klems, Luis L. Fernandes, Gregory J. Ward, Vorapat Inkarojrit, and Mehry Yazdanian Date Published 04/2006 Other Numbers CEC-500-2006-052 Keywords commercial buildings, daylight, daylighting controls, Electrochromic windows, energy efficiency, human factors, peak demand, switchable windows, visual comfort Abstract This guide provides consumer-oriented information about switchable electrochromic (EC) windows. Electrochromic windows change tint with a small applied voltage, providing building owners and occupants with the option to have clear or tinted windows at any time, irrespective of whether it's sunny or cloudy. EC windows can be manually or automatically controlled based on daylight, solar heat gain, glare, view, energy-efficiency, peak electricity demand response, or other criteria. Window controls can be integrated with other building systems, such as lighting and heating/cooling mechanical systems, to optimize interior environmental conditions, occupant comfort, and energy-efficiency.

332

Dual aperture dipole magnet with second harmonic component  

DOE Patents (OSTI)

An improved dual aperture dipole electromagnet includes a second-harmonic frequency magnetic guide field winding which surrounds first harmonic frequency magnetic guide field windings associated with each aperture. The second harmonic winding and the first harmonic windings cooperate to produce resultant magnetic waveforms in the apertures which have extended acceleration and shortened reset portions of electromagnet operation.

Praeg, Walter F. (Palos Park, IL)

1985-01-01T23:59:59.000Z

333

Dual-Mode Space-Temporal Simultaneous Processing Equalizer  

Science Conference Proceedings (OSTI)

A tapped delayed line adaptive array antenna (TDL-AAA) and a space-temporal simultaneous processing equalizer (ST-SPE) are proposed as simple space-temporal equalizers based on minimum mean square error (MMSE) criterion. The ST-SPE has a compact hardware ... Keywords: MMSE, dual-mode, space-temporal simultaneous processing equalizer

Yoshihiro Ichikawa; Shigeki Obote; Kenichi Kagoshima

2005-12-01T23:59:59.000Z

334

Wrought stainless steels -- Dual marking and corrosion evaluation  

SciTech Connect

Prior to the 1980s, the commonly used type 300 austenitic series stainless steels (SS) in the chemical process industry were available in two grades: those with regular carbon content (straight grades) and those with extra-low carbon content (L-grades). When welding the straight grades, it was possible to sensitize the base metal adjacent to the weld. The carbon combines with the chromium at the grain boundaries, leaving a zone depleted of chromium, below the minimum required for SS, adjacent to the grain boundaries. Even a relatively mild corrosive environment then is able to selectively attack this region along grain boundaries. The dual-marked grades (types 304/304L and 316/316L) appeared, with the carbon content of an L-grade and the strength of a straight grade. Initially, there was no national code acceptance for dual marked grades. Designers were obliged to use L-grade stress values. To get around this, people were known to grind off the unacceptable part of the dual marking designation and deliver whatever grade was initially specified. ASME International now has formally stated that dual-marked grades may be used at straight grade stresses for all product forms and piping to 1,000 F (540 C).

Kobrin, G.; Lilly, J.; MacDiarmid, J.; Moniz, B.

1999-10-01T23:59:59.000Z

335

Potential of Malaysian activated carbon in dual purpose adsorption system  

Science Conference Proceedings (OSTI)

The adsorption capability of some locally produced activated charcoal (coconut shell) samples with methanol were taken under laboratory conditions. An experimental test rig was set up; data obtained from the experiments were fitted to Dubinin-Radushkevitch ... Keywords: Malaysian activated carbon, adsorption properties, coefficient of performance (COP), dual purpose system

M. A. Alghoul; M. Y. Sulaiman; K. Sopian; M. Yahya; Azami Zaharim

2008-11-01T23:59:59.000Z

336

On Type IIA geometries dual to N = 2 SCFTs  

E-Print Network (OSTI)

We provide explicit solutions of Type IIA supergravity which are believed to be dual to N = 2 superconformal four dimensional gauge theories. These explicit solutions are based on the general ansatz for such a type of backgrounds introduced by Gaiotto and Maldacena.

R. A. Reid-Edwards; B. Stefanski jr

2010-10-31T23:59:59.000Z

337

SVM based feature selection: why are we using the dual?  

Science Conference Proceedings (OSTI)

Most Support Vector Machines (SVM) implementations are based on solving the dual optimization problem. Of course, feature selection algorithms based on SVM are not different and, in particular, the most used method in the area, Guyon et al.'s Recursive ...

Guillermo L. Grinblat; Javier Izetta; Pablo M. Granitto

2010-11-01T23:59:59.000Z

338

A case for dual-mapping one-way caches  

Science Conference Proceedings (OSTI)

This paper proposes a dual-mapping function for one-way data cache to reduce cache misses, write-back rates, and access time for single-core or multi-core computing processors. Our simulation results show that it reduces cache misses significantly compared ...

Arul Sandeep Gade; Yul Chu

2006-03-01T23:59:59.000Z

339

A Robust Dual-Frequency Radar Profiling Algorithm  

Science Conference Proceedings (OSTI)

In this study, an algorithm to retrieve precipitation from spaceborne dual-frequency (13.8 and 35.6 GHz, or Ku/Ka band) radar observations is formulated and investigated. Such algorithms will be of paramount importance in deriving radar-based and ...

Mircea Grecu; Lin Tian; William S. Olson; Simone Tanelli

2011-07-01T23:59:59.000Z

340

Dual aperture dipole magnet with second harmonic component  

DOE Patents (OSTI)

An improved dual aperture dipole electromagnet includes a second-harmonic frequency magnetic guide field winding which surrounds first harmonic frequency magnetic guide field windings associated with each aperture. The second harmonic winding and the first harmonic windings cooperate to produce resultant magnetic waveforms in the apertures which have extended acceleration and shortened reset portions of electromagnet operation.

Praeg, W.F.

1983-08-31T23:59:59.000Z

Note: This page contains sample records for the topic "advanced sequential dual" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


341

Brief Analysis of dual-rate inferential control systems  

Science Conference Proceedings (OSTI)

For a dual-rate control system where the output sampling interval is an integer multiple of the control interval, we propose a model-based inferential control scheme which uses a fast-rate model to estimate the intersample outputs and then supply them ... Keywords: Digital control, Inferential control, Multirate systems, Robustness, Stability

Dongguang Li; Sirish L. Shah; Tongwen Chen

2002-06-01T23:59:59.000Z

342

Advancing Next-Generation Vehicles  

NLE Websites -- All DOE Office Websites (Extended Search)

the U.S. Department of Energy's (DOE's) lead laboratory for researching advanced vehicle technologies, including hy- the U.S. Department of Energy's (DOE's) lead laboratory for researching advanced vehicle technologies, including hy- brid, plug-in hybrid, battery electric, and alternative fuel vehicles, Argonne provides transportation research critical to advancing the development of next-generation vehicles. Central to this effort is the Lab's Advanced Powertrain Research Facility (APRF), an integrated four-wheel drive chassis dynamometer and component test facility.

343

Advanced Developments in Electron Microscopy  

Science Conference Proceedings (OSTI)

About this Symposium. Meeting, Materials Science & Technology 2011. Symposium, Advanced Developments in Electron Microscopy. Sponsorship, MS&T...

344

Materials Characterization | Advanced Materials | ORNL  

NLE Websites -- All DOE Office Websites (Extended Search)

Characterization Nuclear Forensics Scanning Probes Related Research Materials Theory and Simulation Energy Frontier Research Centers Advanced Materials Home | Science &...

345

Advanced Research Robert R. Romanosky  

E-Print Network (OSTI)

in advanced ultra supercritical (USC) coal-fired power plants. The advanced materials developed in this project are essential for construction of coal-fired boilers with advanced steam cycles involving much higher temperatures and pressures than those presently used in conventional pulverized coal (PC) power

346

A Preliminary Cost Study of the Dual Mode Inverter Controller  

SciTech Connect

In 1998, the Power Electronics and Electric Machinery Research Center (PEEMRC) at the Oak Ridge National Laboratory (ORNL) started a program to investigate alternate field weakening schemes for permanent magnet (PM) motors. The adjective ''alternate'' was used because at that time, outside research emphasis was on motors with interior-mounted PMs (IPMs). The PEEMRC emphasis was placed on motors with surface-mounted PMs (SPMs) because of the relative ease of manufacturing SPM motors compared with the IPM motors. Today the PEEMRC is continuing research on SPMs while examining the IPMs that have been developed by industry. Out of this task--the goal of which was to find ways to drive PM motors that inherently have low inductance at high speeds where their back-emf exceeds the supply voltage--ORNL developed and demonstrated the dual mode inverter control (DMIC) [1,2] method of field weakening for SPM motors. The predecessor of DMIC is conventional phase advance (CPA), which was developed by UQM Technologies, Inc. [3]. Fig. 1 shows the three sets of anti-parallel thyristors in the dashed box that comprise the DMIC. If one removes the dashed box by shorting each set of anti-parallel thyristors, the configuration becomes a conventional full bridge inverter on the left driving a three phase motor on the right. CPA may be used to drive this configuration ORNL's initial analyses of CPA and DMIC were based on driving motors with trapezoidal back-emfs [4-6], obtained using double layer lapped stator windings with one slot per pole per phase. A PM motor with a sinusoidal back-emf obtained with two poles per slot per phase has been analyzed under DMIC operation as a University of Tennessee-Knoxville (UTK) doctoral dissertation [7]. In the process of this research, ORNL has completed an analysis that explains and quantifies the role of inductance in these methods of control. The Appendix includes information on the equations for the three components of phase inductance, L{sub gap}, L{sub slot}, and L{sub endturns}. PM motors inherently have a lower inductance because of the increase in effective air gap caused by the magnet, which is in the denominator of the equation for L{sub gap}. L{sub gap} accounts for about half of the phase inductance. Because of the low inductance, there is a propensity for currents to exceed the motor's rated value. DMIC solves this problem for low-inductance PM motors and, in addition, provides a number of safety features that protect against uncontrolled generator mode operation [8,9]; however, the DMIC topology adds a pair of anti-parallel thyristors in each of the three phases, thereby introducing additional silicon costs as well as additional voltage drops during operation. It poses the tradeoff question; under what conditions can the beneficial features of DMIC offset its additional silicon cost and voltage drop losses? The purpose of this report is to address the tradeoff question. Sections of the report will: (1) review the role of self-inductance in performance and control of PM motors, (2) discuss the bounding inductances for motors with trapezoidal back-emfs under CPA control, (3) discuss the bounding inductances for trapezoidal back-emfs under DMIC, (4) discuss the bounding inductances for the PM synchronous motor (PMSM), (5) present the analysis showing how DMIC minimizes current in PMSMs, (6) present the results of a cost study conducted for two motors driven using a CPA inverter and for two motors driven using DMIC, (7) discuss estimating life cycle cost benefits, and (8) present conclusions.

McKeever, J.W.

2005-01-28T23:59:59.000Z

347

A Preliminary Cost Study of the Dual Mode Inverter Controller  

SciTech Connect

In 1998, the Power Electronics and Electric Machinery Research Center (PEEMRC) at the Oak Ridge National Laboratory (ORNL) started a program to investigate alternate field weakening schemes for permanent magnet (PM) motors. The adjective ''alternate'' was used because at that time, outside research emphasis was on motors with interior-mounted PMs (IPMs). The PEEMRC emphasis was placed on motors with surface-mounted PMs (SPMs) because of the relative ease of manufacturing SPM motors compared with the IPM motors. Today the PEEMRC is continuing research on SPMs while examining the IPMs that have been developed by industry. Out of this task--the goal of which was to find ways to drive PM motors that inherently have low inductance at high speeds where their back-emf exceeds the supply voltage--ORNL developed and demonstrated the dual mode inverter control (DMIC) [1,2] method of field weakening for SPM motors. The predecessor of DMIC is conventional phase advance (CPA), which was developed by UQM Technologies, Inc. [3]. Fig. 1 shows the three sets of anti-parallel thyristors in the dashed box that comprise the DMIC. If one removes the dashed box by shorting each set of anti-parallel thyristors, the configuration becomes a conventional full bridge inverter on the left driving a three phase motor on the right. CPA may be used to drive this configuration ORNL's initial analyses of CPA and DMIC were based on driving motors with trapezoidal back-emfs [4-6], obtained using double layer lapped stator windings with one slot per pole per phase. A PM motor with a sinusoidal back-emf obtained with two poles per slot per phase has been analyzed under DMIC operation as a University of Tennessee-Knoxville (UTK) doctoral dissertation [7]. In the process of this research, ORNL has completed an analysis that explains and quantifies the role of inductance in these methods of control. The Appendix includes information on the equations for the three components of phase inductance, L{sub gap}, L{sub slot}, and L{sub endturns}. PM motors inherently have a lower inductance because of the increase in effective air gap caused by the magnet, which is in the denominator of the equation for L{sub gap}. L{sub gap} accounts for about half of the phase inductance. Because of the low inductance, there is a propensity for currents to exceed the motor's rated value. DMIC solves this problem for low-inductance PM motors and, in addition, provides a number of safety features that protect against uncontrolled generator mode operation [8,9]; however, the DMIC topology adds a pair of anti-parallel thyristors in each of the three phases, thereby introducing additional silicon costs as well as additional voltage drops during operation. It poses the tradeoff question; under what conditions can the beneficial features of DMIC offset its additional silicon cost and voltage drop losses? The purpose of this report is to address the tradeoff question. Sections of the report will: (1) review the role of self-inductance in performance and control of PM motors, (2) discuss the bounding inductances for motors with trapezoidal back-emfs under CPA control, (3) discuss the bounding inductances for trapezoidal back-emfs under DMIC, (4) discuss the bounding inductances for the PM synchronous motor (PMSM), (5) present the analysis showing how DMIC minimizes current in PMSMs, (6) present the results of a cost study conducted for two motors driven using a CPA inverter and for two motors driven using DMIC, (7) discuss estimating life cycle cost benefits, and (8) present conclusions.

McKeever, J.W.

2005-01-28T23:59:59.000Z

348

Advanced Green Technologies | Open Energy Information  

Open Energy Info (EERE)

Advanced Green Technologies Place Fort Lauderdale, Florida Zip 33311 Product Advanced Green Technologies is a US-based distributor of PV systems. It is owned by Advanced Roofing...

349

Draft Advanced Fossil Solicitation | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Advanced Fossil Solicitation Federal loan guarantee solicitation announcement -- Advanced Fossil Energy Projects. Microsoft Word - Draft Advanced Fossil Solicitation Final Draft.1...

350

Manufacturing Science and Technology: Advanced Manufacturing...  

NLE Websites -- All DOE Office Websites (Extended Search)

Contacts Advanced Manufacturing Trades Training Program Business Program Lead Yvonne Baros Advanced Manufacturing Trades Training Program Tom Souther Advanced Technology Academy...

351

Advanced Manufacturing Office: NewsDetail  

NLE Websites -- All DOE Office Websites (Extended Search)

Office: NewsDetail on Twitter Bookmark Advanced Manufacturing Office: NewsDetail on Google Bookmark Advanced Manufacturing Office: NewsDetail on Delicious Rank Advanced...

352

Removal of polychlorinated phenols in sequential anaerobic-aerobic biofilm reactors packed with tire chips  

Science Conference Proceedings (OSTI)

Scrap vehicle tire chips were used as packing material for sequential anaerobic-aerobic biofilm reactors to remove persistent chlorinated hydrocarbons. Adsorption capacity of scrap tires was greater under acidic conditions than under basic conditions. However, it was only approximately 0.04 to 0.3% of that of activated carbon. The amount of biomass that attached to the surface of scrap tires was 3.16 and 3.72 mg volatile suspended solids/cm{sup 2} after 14 and 37 days, respectively. Two laboratory-scale, down-flow anaerobic-aerobic biofilm reactors packed with tire chips were operated to remove 2,4-dichlorophenol (DCP) and 4-chlorophenol (CP). More than 98% of DCP was dehalogenated to CP in the anaerobic reactor, 70 to 98% of which was subsequently degraded in the aerobic reactor. Scrap tires did not cause any operational problems when used as biofilter media.

Shin, H.S.; Yoo, K.S.; Park, J.K.

1999-05-01T23:59:59.000Z

353

Regeneration of strong-base anion-exchange resins by sequential chemical displacement  

DOE Patents (OSTI)

A method for regenerating strong-base anion exchange resins utilizing a sequential chemical displacement technique with new regenerant formulation. The new first regenerant solution is composed of a mixture of ferric chloride, a water-miscible organic solvent, hydrochloric acid, and water in which tetrachloroferrate anion is formed and used to displace the target anions on the resin. The second regenerant is composed of a dilute hydrochloric acid and is used to decompose tetrachloroferrate and elute ferric ions, thereby regenerating the resin. Alternative chemical displacement methods include: (1) displacement of target anions with fluoroborate followed by nitrate or salicylate and (2) displacement of target anions with salicylate followed by dilute hydrochloric acid. The methodology offers an improved regeneration efficiency, recovery, and waste minimization over the conventional displacement technique using sodium chloride (or a brine) or alkali metal hydroxide.

Brown, Gilbert M. (Knoxville, TN); Gu, Baohua (Oak Ridge, TN); Moyer, Bruce A. (Oak Ridge, TN); Bonnesen, Peter V. (Knoxville, TN)

2002-01-01T23:59:59.000Z

354

Transparent Parallel Image Processing by way of a Familiar Sequential API  

E-Print Network (OSTI)

This paper describes an infrastructure that enables transparent development of image processing software for parallel computers. The infrastructure's main component is an image processing library containing operations capable of running on distributed memory MIMD-style parallel hardware. Since the library has a programming interface identical to that of a familiar sequential image processing library, the parallelism is completely hidden from the user. All library functions are based on an abstract parallel image processing machine (APIPM), introduced in this paper. To guide the process of automatic parallelization and optimization, a performance model is defined for operations implemented using APIPM instructions. Experiments show that for realistic image operations performance predictions are highly accurate. These results suggest that the infrastructure 's core forms a powerful basis for automatic parallelization and optimization of complete applications.

Seinstra And Koelma; F. J. Seinstra; D. Koelma

2000-01-01T23:59:59.000Z

355

Expert system for identification of simultaneous and sequential reactor fuel failures with gas tagging  

DOE Patents (OSTI)

Failure of a fuel element in a nuclear reactor core is determined by a gas tagging failure detection system and method. Failures are catalogued and characterized after the event so that samples of the reactor's cover gas are taken at regular intervals and analyzed by mass spectroscopy. Employing a first set of systematic heuristic rules which are applied in a transformed node space allows the number of node combinations which must be processed within a barycentric algorithm to be substantially reduced. A second set of heuristic rules treats the tag nodes of the most recent one or two leakers as "background" gases, further reducing the number of trial node combinations. Lastly, a "fuzzy" set theory formalism minimizes experimental uncertainties in the identification of the most likely volumes of tag gases. This approach allows for the identification of virtually any number of sequential leaks and up to five simultaneous gas leaks from fuel elements.

Gross, Kenny C. (Bolingbrook, IL)

1994-01-01T23:59:59.000Z

356

Advanced Biofuels Workshop  

Gasoline and Diesel Fuel Update (EIA)

August 1, 2012 August 1, 2012 In Attendance U.S. Energy Information Administration 1000 Independence Ave. SW, Room 2E-069 Washington, DC 20585 Adam Sieminski EIA Terry Higgins Hart Downstream Energy Services Peter Ryus RSB Services Foundation Zia Haq DOE Robert Kozak Atlantic Biomass Conversion Leticia Phillips UNICA/Brazillian Sugarecane Industry Assoc. Paul Kamp Leifmark, LLC/Inbicon Biomass Steve Gerber Fiberight Joanne Ivancic Advanced Biofuels USA John G. Cowie Agenda 2020 Technology Alliance Jeff Hazle American Fuel & Petrochemical Manufacturers Bryan Just American Petroleum Institute Barry Bernfeld Bunge Global Agribusiness Michael Corbin CLF Partners International LLC Paul Grabowski DOE, Office of Biomass Program

357

Advanced Demand Responsive Lighting  

NLE Websites -- All DOE Office Websites (Extended Search)

Demand Demand Responsive Lighting Host: Francis Rubinstein Demand Response Research Center Technical Advisory Group Meeting August 31, 2007 10:30 AM - Noon Meeting Agenda * Introductions (10 minutes) * Main Presentation (~ 1 hour) * Questions, comments from panel (15 minutes) Project History * Lighting Scoping Study (completed January 2007) - Identified potential for energy and demand savings using demand responsive lighting systems - Importance of dimming - New wireless controls technologies * Advanced Demand Responsive Lighting (commenced March 2007) Objectives * Provide up-to-date information on the reliability, predictability of dimmable lighting as a demand resource under realistic operating load conditions * Identify potential negative impacts of DR lighting on lighting quality Potential of Demand Responsive Lighting Control

358

Horizontal Advanced Tensiometer  

DOE Patents (OSTI)

An horizontal advanced tensiometer is described that allows the monitoring of the water pressure of soil positions, particularly beneath objects or materials that inhibit the use of previous monitoring wells. The tensiometer includes a porous cup, a pressure transducer (with an attached gasket device), an adaptive chamber, at least one outer guide tube which allows access to the desired horizontal position, a transducer wire, a data logger and preferably an inner guide tube and a specialized joint which provides pressure on the inner guide tube to maintain the seal between the gasket of the transducer and the adaptive chamber.

Hubbell, Joel M.; Sisson, James B.

2004-06-22T23:59:59.000Z

359

Design of Transport Casks with Depleted Uranium Gamma Shield and Advanced Safety  

NLE Websites -- All DOE Office Websites (Extended Search)

Transport Casks with Depleted Uranium Gamma Shield and Advanced Safety Transport Casks with Depleted Uranium Gamma Shield and Advanced Safety Matveev V.Z., Morenko A.I., Shapovalov V.I. Russian Federal Nuclear Center - All-Russian Research Institute of Experimental Physics (RFNC-VNIIEF) 37 Mira Prospect, Sarov, Russia, 607190, matveev@vniief.ru Maslov A.A., Orlov V.K., Semenov A.G., Sergeev V.M., Yuferov O.I., Visik A.M. Bochvar Institute of Inorganic Materials (VNIINM) 5-A Rogova street, p.b. 369, Moscow, Russia, 123060, majul2000@mail.ru Abstract - The report is dedicated to a problem of creation of a new generation of dual-purpose transport packing complete sets (TPCS) 1 with advanced safety. These sets are intended for transportation and storage of spent nuclear fuel assemblies (SNFA) 2 of VVER reactors and spent spark elements (SSE)

360

NETL: Advanced Research - Materials  

NLE Websites -- All DOE Office Websites (Extended Search)

High Performance Materials > Chrome Oxide Refractory High Performance Materials > Chrome Oxide Refractory Advanced Research High Performance Materials Chrome Oxide Refractory One notable NETL success is the development of a chrome oxide refractory material capable of working in slagging gasifier conditions. In this project, researchers first determined that one of the major failure mechanisms for chrome oxide refractories exposed to the intense heat and corrosive environment was spalling, or the chipping or flaking of refractory material from an exposed face. They used this information to formulate a high-chrome oxide refractory composition that resists spalling, resulting in a refractory with a longer service life in the gasifier. Inside an ultrasupercritical (USC) pulverized coal power plant, materials are exposed to temperatures up to 760°C and pressures up to 5,000 psi. Operating a USC system can improve power plant efficiency up to 47% and reduce emissions. However, finding boiler and turbine materials that can hold up under extreme conditions requires new high-temperature metal alloys and ceramic coatings, as well as computational modeling research to optimize the processing of these materials. Advanced Research Materials Development program successes in this area include the following:

Note: This page contains sample records for the topic "advanced sequential dual" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


361

Advanced PFBC transient analysis  

SciTech Connect

Transient modeling and analysis of advanced Pressurized Fluidized Bed Combustion (PFBC) systems is a research area that is currently under investigation by the US Department of Energy`s Federal Energy Technology Center (FETC). The object of the effort is to identify key operating parameters that affect plant performance and then quantify the basic response of major sub-systems to changes in operating conditions. PC-TRAX{trademark}, a commercially available dynamic software program, was chosen and applied in this modeling and analysis effort. This paper describes the development of a series of TRAX-based transient models of advanced PFBC power plants. These power plants burn coal or other suitable fuel in a PFBC, and the high temperature flue gas supports low-Btu fuel gas or natural gas combustion in a gas turbine topping combustor. When it is utilized, the low-Btu fuel gas is produced in a bubbling bed carbonizer. High temperature, high pressure combustion products exiting the topping combustor are expanded in a modified gas turbine to generate electrical power. Waste heat from the system is used to raise and superheat steam for a reheat steam turbine bottoming cycle that generates additional electrical power. Basic control/instrumentation models were developed and modeled in PC-TRAX and used to investigate off-design plant performance. System performance for various transient conditions and control philosophies was studied.

White, J.S. [Parsons Power Group, Inc., Reading, PA (United States); Bonk, D.L. [USDOE Federal Energy Technology Center, Morgantown, WV (United States)

1997-05-01T23:59:59.000Z

362

Advanced PFBC transient analysis  

SciTech Connect

Transient modeling and analysis of Advanced Pressurized Fluidized Bed Combustion (PFBC) systems is a research area that is currently under investigative study by the United States Department of Energy`s Morgantown Energy Technology Center (METC). The object of the effort is to identify key operating parameters affecting plant performance and then quantify the basic response of major sub-systems to changes in operating conditions. PC-TRAX, a commercially available dynamic software program, was chosen and applied in this modeling and analysis effort. This paper summarizes and describes the development of a series of TRAX-based transient models of Advanced PFBC power plants. These power plants generate a high temperature flue gas by burning coal or other suitable fuel in a PFBC. The high temperature flue gas supports low-Btu fuel gas or natural gas combustion in a gas turbine topping combustor. When utilized, low-Btu fuel gas is produced in a bubbling bed carbonizer. High temperature, high pressure combustion products exiting the topping combustor are expanded in a modified gas turbine to generate electrical power. Waste heat from the system is used to generate and superheat steam for a reheat steam turbine bottoming cycle that generates additional electrical power. Basic control/instrumentation models were developed and modeled in PC-TRAX and used to investigate off-design plant performance. System performance for various transient conditions and control philosophies was studied.

White, J.S. [Parsons Power Group, Inc., Reading, PA (United States); Bonk, D.L.; Rogers, L. [USDOE Morgantown Energy Technology Center, WV (United States)

1996-12-31T23:59:59.000Z

363

Advanced converter reactors  

SciTech Connect

Advanced converter reactors (ACRs) of primary US interest are those which can be commercialized within about 20 years, and are: Advanced Light-Water Reactors, Spectral-Shift-Control Reactors, Heavy-Water Reactors (CANDU type), and High-Temperature Gas-Cooled Reactors. These reactors can operate on uranium, thorium, or uranium-thorium fuel cycles, but have the greatest fuel utilization on thorium type cycles. The water reactors tend to operate more economically on uranium cycles, while the HTGR is more economical on thorium cycles. Thus, the HTGR had the greatest practical potential for improving fuel utilization. If the US has 3.4 to 4 million tons U/sub 3/O/sub 8/ at reasonable costs, ACRs can make important contributions to maintaining a high nuclear power level for many decades; further, they work well with fast breeder reactors in the long term under symbiotic fueling conditions. Primary nuclear data needs of ACRs are integral measurements of reactivity coefficients and resonance absorption integrals.

Kasten, P.R.

1979-01-01T23:59:59.000Z

364

Advanced Metering Infrastructure  

SciTech Connect

The report provides an overview of the development of Advanced Metering Infrastructure (AMI). Metering has historically served as the cash register for the utility industry. It measured the amount of energy used and supported the billing of customers for that usage. However, utilities are starting to look at meters in a whole different way, viewing them as the point of contact with customers in supporting a number of operational imperatives. The combination of smart meters and advanced communications has opened up a variety of methods for utilities to reduce operating costs while offering new services to customers. A concise look is given at what's driving interest in AMI, the components of AMI, and the creation of a business case for AMI. Topics covered include: an overview of AMI including the history of metering and development of smart meters; a description of the key technologies involved in AMI; a description of key government initiatives to support AMI; an evaluation of the current market position of AMI; an analysis of business case development for AMI; and, profiles of 21 key AMI vendors.

NONE

2007-10-15T23:59:59.000Z

365

Advanced desiccant materials research  

DOE Green Energy (OSTI)

The long-range goal of this task is to understand the role of surface phenomena in desiccant cooling materials. The background information includes a brief introduction to desiccant cooling systems (DCS) and the role of the desiccant as a system component. The purpose, background, rationale, and long-term technical approach for studying advanced desiccant materials are then treated. Experimental methods for measuring water vapor sorption by desiccants are described, and the rationale is then given for choosing a quartz crystal microbalance (QCM) for measuring sorption isotherms, rates, and cyclic stability. Background information is given about the QCM, including the quartz crystal resonator itself, the support structure for the quartz crystal, and the advantages and limitations of a QCM. The apparatus assembled and placed into operation during CY 1985 is described. The functions of the principal components of the equipment, i.e., the QCM, vacuum system, pressure gauges, residual gas analyzer, constant temperature bath, and data acquisition system, are described as they relate to the water vapor sorption measurements now under way. The criteria for narrowing the potential candidates as advanced desiccant materials for the initial studies are given. Also given is a list of 20 principal candidate materials identified based on the criteria and data available in the literature.

Czanderna, A.W.; Thomas, T.M.

1986-05-01T23:59:59.000Z

366

J.Org. Chem. 1984,49, 3033-3035 3033 Proposed SequentialConversion of Coal's  

E-Print Network (OSTI)

J.Org. Chem. 1984,49, 3033-3035 3033 SchemeI. @& Proposed SequentialConversion of Coal's Native moieties (func- tionalities determined to be important for lignins6and for low-rank coals'). In contrast "C, is one of condensation to make a dimeric furan! Sincein a coal systemthere will be some available

367

CRM strategies for a small-sized online shopping mall based on association rules and sequential patterns  

Science Conference Proceedings (OSTI)

As dot-com bubble burst in 2002, an uncountable number of small-sized online shopping malls have emerged every day due to many good characteristics of online marketplace, including significantly reduced search costs and menu cost for products or services ... Keywords: Association rule, CRM strategy, Data mining, RFM, Sequential pattern

Beomsoo Shim; Keunho Choi; Yongmoo Suh

2012-07-01T23:59:59.000Z

368

Synthesis and optimization of multiple-valued combinational and sequential reversible circuits with don't cares  

Science Conference Proceedings (OSTI)

In this paper, a synthesis method for combinational multiple-valued reversible logic (MVRL) circuits is proposed. This algorithm can use the don't care values in the synthesis process to obtain the optimal circuit with respect to quantum cost. The binary ... Keywords: Multiple-valued reversible logic, Optimization, Reversible logic, Sequential reversible logic, Synthesis

Aliakbar Niknafs; Majid Mohammadi

2013-03-01T23:59:59.000Z

369

Sequential Printing by Laser-Induced Forward Transfer To Fabricate a Polymer Light-Emitting Diode Pixel  

E-Print Network (OSTI)

Sequential Printing by Laser-Induced Forward Transfer To Fabricate a Polymer Light-Emitting Diode-1015, Lausanne, Switzerland ABSTRACT: Patterned deposition of polymer light-emitting diode (PLED Organic light-emitting diodes (OLEDs) have been investigated in detail for nearly a quarter of a century,1

370

Constructive proof of the existence of equilibrium in competitive economy with sequentially locally non-constant excess demand functions by Sperner's lemma  

E-Print Network (OSTI)

Using Sperner's lemma for modified partition of a simplex we will constructively prove the existence of equilibrium in competitive economy with sequentially locally non-constant excess demand functions. And we will show the converse result that the existence of equilibrium in competitive economy with sequentially locally non-constant excess demand functions implies Sperner's lemma. We follow the Bishop style constructive mathematics.

Tanaka, Yasuhito

2011-01-01T23:59:59.000Z

371

ADVANCED TURBINE SYSTEMS PROGRAM  

SciTech Connect

Natural gas combustion turbines are rapidly becoming the primary technology of choice for generating electricity. At least half of the new generating capacity added in the US over the next twenty years will be combustion turbine systems. The Department of Energy has cosponsored with Siemens Westinghouse, a program to maintain the technology lead in gas turbine systems. The very ambitious eight year program was designed to demonstrate a highly efficient and commercially acceptable power plant, with the ability to fire a wide range of fuels. The main goal of the Advanced Turbine Systems (ATS) Program was to develop ultra-high efficiency, environmentally superior and cost effective competitive gas turbine systems for base load application in utility, independent power producer and industrial markets. Performance targets were focused on natural gas as a fuel and included: System efficiency that exceeds 60% (lower heating value basis); Less than 10 ppmv NO{sub x} emissions without the use of post combustion controls; Busbar electricity that are less than 10% of state of the art systems; Reliability-Availability-Maintainability (RAM) equivalent to current systems; Water consumption minimized to levels consistent with cost and efficiency goals; and Commercial systems by the year 2000. In a parallel effort, the program was to focus on adapting the ATS engine to coal-derived or biomass fuels. In Phase 1 of the ATS Program, preliminary investigators on different gas turbine cycles demonstrated that net plant LHV based efficiency greater than 60% was achievable. In Phase 2 the more promising cycles were evaluated in greater detail and the closed-loop steam-cooled combined cycle was selected for development because it offered the best solution with least risk for achieving the ATS Program goals for plant efficiency, emissions, cost of electricity and RAM. Phase 2 also involved conceptual ATS engine and plant design and technology developments in aerodynamics, sealing, combustion, cooling, materials, coatings and casting development. The market potential for the ATS gas turbine in the 2000-2014 timeframe was assessed for combined cycle, simple cycle and integrated gasification combined cycle, for three engine sizes. The total ATS market potential was forecasted to exceed 93 GW. Phase 3 and Phase 3 Extension involved further technology development, component testing and W501ATS engine detail design. The technology development efforts consisted of ultra low NO{sub x} combustion, catalytic combustion, sealing, heat transfer, advanced coating systems, advanced alloys, single crystal casting development and determining the effect of steam on turbine alloys. Included in this phase was full-load testing of the W501G engine at the McIntosh No. 5 site in Lakeland, Florida.

Gregory Gaul

2004-04-21T23:59:59.000Z

372

Vehicle Technologies Office: Advanced Combustion Engines  

NLE Websites -- All DOE Office Websites (Extended Search)

Advanced Combustion Advanced Combustion Engines to someone by E-mail Share Vehicle Technologies Office: Advanced Combustion Engines on Facebook Tweet about Vehicle Technologies Office: Advanced Combustion Engines on Twitter Bookmark Vehicle Technologies Office: Advanced Combustion Engines on Google Bookmark Vehicle Technologies Office: Advanced Combustion Engines on Delicious Rank Vehicle Technologies Office: Advanced Combustion Engines on Digg Find More places to share Vehicle Technologies Office: Advanced Combustion Engines on AddThis.com... Just the Basics Hybrid & Vehicle Systems Energy Storage Advanced Power Electronics & Electrical Machines Advanced Combustion Engines Combustion Engines Emission Control Waste Heat Recovery Fuels & Lubricants Materials Technologies Advanced Combustion Engines

373

Advanced Reactor Technologies | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Advanced Reactor Advanced Reactor Technologies Advanced Reactor Technologies Advanced Reactor Technologies Advanced Reactor Technologies The Office of Advanced Reactor Technologies (ART) sponsors research, development and deployment (RD&D) activities through its Next Generation Nuclear Plant (NGNP), Advanced Reactor Concepts (ARC), and Advanced Small Modular Reactor (aSMR) programs to promote safety, technical, economical, and environmental advancements of innovative Generation IV nuclear energy technologies. The Office of Nuclear Energy (NE) will pursue these advancements through RD&D activities at the Department of Energy (DOE) national laboratories and U.S. universities, as well as through collaboration with industry and international partners. These activities will focus on advancing scientific

374

A dual mass flux framework for boundary layer convection  

NLE Websites -- All DOE Office Websites (Extended Search)

A dual mass flux framework for boundary layer convection A dual mass flux framework for boundary layer convection Neggers, Roel European Centre for Medium-range Weather Forecasts (ECMWF) Category: Modeling A new convective boundary layer scheme is presented that is currently being developed for the Integrated Forecasting System (IFS) of the European Centre for Medium-range Weather Forecasts (ECMWF). Part of the total turbulent flux is modeled through advective mass flux by multiple updrafts, initialized at the surface. Two groups of updrafts are explicitly represented; i) updrafts that never reach their lifting condensation level, and ii) updrafts that condensate and become cloudy. Key new ingredient is the flexibility of the associated updraft area fractions, as a function of model state. As a result, an extra degree of freedom is introduced in the

375

String Gas Shells, their Dual Radiation and Hedgehog Signature Control  

E-Print Network (OSTI)

We search for spherically symmetric, stationary solutions with a string gas shell as a source. The requirement of a uniform newtonian potential, or constancy of the 00 component of the metric, implies the existence of a "dual" radiation, which we argue can be interpreted as representing the virtual quantum fluctuations that stabilize the shell. A string hedgehog can be introduced also into the solution. For zero or small hedgehog strength the string gas shell is of a regular nature, while the dual radiation is of a spacelike nature. For higher hedgehog strengths however the radiation "materializes" and becomes timelike while the string gas shell becomes space like. The significance of these solutions for the quantum theory is discussed.

E. I. Guendelman

2009-03-12T23:59:59.000Z

376

Single-stage dual priority regulator for photovoltaic systems  

DOE Green Energy (OSTI)

In this paper the design and application of a voltage regulator for use in Photovoltaic Systems with two separate loads of different priority is presented. The Single-Stage Dual Priority Regulator (SSDPR) charges two separate battery systems for high and low priority loads. The controller always charges the main battery first. It toggles between the two batteries when the main battery is nearly charged, and reduces the charge duty cycle of the main battery as it approaches full charge. The SSDPR utilizes the PV more efficiently by supplying low priority loads without jeopardizing the reliability of the critical load. Both the main and auxiliary voltage settings are adjustable, allowing the use of different types of batteries. The SDPR is being tested in the University of Lowell Vaccine Refrigerator Laboratory. A dual priority regulator is useful in any stand-alone system with multiple loads. Uses include photovoltaic powered homes, medical clinics, and recreational vehicles.

Salameh, Z.M.; Lynch, W.A. (Univ. of Massachusetts, Lowell (United States))

1992-01-01T23:59:59.000Z

377

Dual superconductivity and vacuum properties in Yang--Mills theories  

E-Print Network (OSTI)

We address, within the dual superconductivity model for color confinement, the question whether the Yang-Mills vacuum behaves as a superconductor of type I or type II. In order to do that we compare, for the theory with gauge group SU(2), the determination of the field penetration depth $\\lambda$ with that of the superconductor correlation length $\\xi$. The latter is obtained by measuring the temporal correlator of a disorder parameter developed by the Pisa group to detect dual superconductivity. The comparison places the vacuum close to the border between type I and type II and marginally on the type II side. We also check our results against the study of directly measurable effects such as the interaction between two parallel flux tubes, obtaining consistent indications for a weak repulsive behaviour. Future strategies to improve our investigation are discussed.

A. D'Alessandro; M. D'Elia; L. Tagliacozzo

2006-07-12T23:59:59.000Z

378

Dual Superconductivity from Yang-Mills Theory via Connection Decomposition  

E-Print Network (OSTI)

We derive an Abelian-Higgs-like action from SU(2) Yang-Mills theory via monopole-condensation assumption. Abelian projection as well as chromo-'electric-magnetic' duality are naturally realized by separating the small off-diagonal gluon part from diagonal gluon field according to the order of inverse coupling constant($1/g$). It is shown that Abelian dominance can follow from infrared behavior of ranning coupling constant and the mass generation of chromo-electric field as well as off-diagonal gluon is due to the quantum fluctuation of orientation of Abelian direction. Dual superconductivity of theory vacuum is confirmed by deriving dual London equation for chromo-electronic field.

Duoje Jia

2005-09-03T23:59:59.000Z

379

Wilson loops in string duals of walking and flavored systems  

Science Conference Proceedings (OSTI)

We consider the vacuum expectation value of Wilson loop operators by studying the behavior of string probes in solutions of type-IIB string theory generated by N{sub c} D5-branes wrapped on an S{sup 2} internal manifold. In particular, we focus on solutions to the background equations that are dual to field theories with a walking gauge coupling as well as for flavored systems. We present in detail our walking solution and emphasize various general aspects of the procedure to study Wilson loops using string duals. We discuss the special features that the strings show when probing the region associated with the walking of the field-theory coupling.

Nunez, Carlos; Piai, Maurizio; Rago, Antonio [Swansea University, School of Physical Sciences, Singleton Park, Swansea, Wales (United Kingdom)

2010-04-15T23:59:59.000Z

380

Chemistry & Physics at Interfaces | Advanced Materials | ORNL  

NLE Websites -- All DOE Office Websites (Extended Search)

from Atoms to Systems Materials Characterization Materials Theory and Simulation Energy Frontier Research Centers Advanced Materials Home | Science & Discovery | Advanced...

Note: This page contains sample records for the topic "advanced sequential dual" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


381

Advanced Materials and Processes for Extreme Environments  

Science Conference Proceedings (OSTI)

Symposium, Advanced Materials and Reservoir Engineering for Extreme Oil & Gas Environments. Presentation Title, Advanced Materials and Processes for...

382

Advanced Materials Technologies - Energy Innovation Portal  

Advanced Materials Technology Marketing Summaries Here youll find marketing summaries of advanced materials technologies available for licensing from ...

383

Irradiation Performance of Advanced and Model Alloys  

Science Conference Proceedings (OSTI)

Mar 14, 2012 ... Mechanical Performance of Materials for Current and Advanced Nuclear Reactors: Irradiation Performance of Advanced and Model Alloys

384

Advanced Metering Infrastructure Security Considerations | Department...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Metering Infrastructure Security Considerations Advanced Metering Infrastructure Security Considerations The purpose of this report is to provide utilities implementing Advanced...

385

News and Awards | Advanced Materials | ORNL  

NLE Websites -- All DOE Office Websites (Extended Search)

Events and Conferences Supporting Organizations Advanced Materials Home | Science & Discovery | Advanced Materials | News & Awards SHARE News and Awards Latest News...

386

Advanced Technology Vehicles Manufacturing Incentive Program...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Technology Vehicles Manufacturing Incentive Program Advanced Technology Vehicles Manufacturing Incentive Program A fact sheet detailling the advanced technology vehicles...

387

Advanced Light Source Activity Report 2002  

E-Print Network (OSTI)

ALS and the Advanced Photon Source (APS). The LDLR crystals,Director for the Advanced Photon Source (APS), and Steven

Duque editor, Theresa; Greiner editor, Annette; Moxon editor, Elizabeth; Robinson editor, Arthur; Tamura editor, Lori

2003-01-01T23:59:59.000Z

388

Advanced Photon Source  

NLE Websites -- All DOE Office Websites (Extended Search)

Home Home Group Members Accelerator Magnets Insertion Devices Facilities Presentations & Publications Internal Magnetic Devices Group The primary mission of the Magnetic Devices (MD) Group is to design, build, and maintain Insertion Devices (IDs) that are reliable and transparent to the electron beam at the Advanced Photon Source (APS). The majority of IDs at the APS are conventional planar hybrid undulators, but an essential part of the mission is to develop novel IDs, such as short-period superconducting undulators and long-period electromagnetic undulators. The capabilities of APS IDs are matched to users' experimental needs. The mission also includes magnetic tuning of the IDs to ensure their near-ideal performance as x-ray sources and calculations to predict the radiation

389

Visiting | Advanced Photon Source  

NLE Websites -- All DOE Office Websites (Extended Search)

Visiting the APS Visiting the APS If you have questions or need assistance planning your visit, please contact the APS User Office. Obtaining site access: General info: Visitors and new users | Non-U.S. Citizens Visitor registration: request access as a visitor who will not do hands-on work (guests, family members, students, etc.) Traveling to the APS: Transportation: Resources | University of Chicago Shuttle external link Directions: to Argonne | to the APS User Office Maps: Argonne Campus external link | Conference Center (402) | APS Facility & Beamlines | Parking Currency: The hotels and banks near Argonne do not exchange currency. Plan on using major credit cards, U.S. traveler's checks, or exchange currency in advance at the airport. See also: The Universal Currency Converter(tm) external link

390

Welcome | Advanced Photon Source  

NLE Websites -- All DOE Office Websites (Extended Search)

Welcome Welcome Aerial view of APS Aerial view of the APS Welcome to the Advanced Photon Source (APS) at Argonne National Laboratory. Whether you are a current or potential scientific user of our unique facility or are simply interested in learning more about the APS, we are delighted that you are visiting our website. The APS is funded by the Office of Science, Office of Basic Energy Sciences in the U.S. Department of Energy. We operate a National User Facility that is open to everyone who has a need for extremely brilliant x-ray photon beams. The APS is one of the most technologically complex machines in the world. This premier national research facility provides the brightest x-ray beams in the Western Hemisphere to more than 5,000 (and growing) scientists from

391

Advanced Containment System  

SciTech Connect

An advanced containment system for containing buried waste and associated leachate. A trench is dug on either side of the zone of interest containing the buried waste so as to accommodate a micro tunnel boring machine. A series of small diameter tunnels are serially excavated underneath the buried waste. The tunnels are excavated by the micro tunnel boring machine at a consistent depth and are substantially parallel to each other. As tunneling progresses, steel casing sections are connected end to end in the excavated portion of the tunnel so that a steel tube is formed. Each casing section has complementary interlocking structure running its length that interlocks with complementary interlocking structure on the adjacent casing section. Thus, once the first tube is emplaced, placement of subsequent tubes is facilitated by the complementary interlocking structure on the adjacent, previously placed, casing sections.

Kostelnik, Kevin M. (Idaho Falls, ID); Kawamura, Hideki (Tokyo, JP); Richardson, John G. (Idaho Falls, ID); Noda, Masaru (Tokyo, JP)

2005-05-24T23:59:59.000Z

392

Advanced Containment System  

SciTech Connect

An advanced containment system for containing buried waste and associated leachate. A trench is dug on either side of the zone of interest containing the buried waste so as to accommodate a micro tunnel boring machine. A series of small diameter tunnels are serially excavated underneath the buried waste. The tunnels are excavated by the micro tunnel boring machine at a consistent depth and are substantially parallel to each other. As tunneling progresses, steel casing sections are connected end to end in the excavated portion of the tunnel so that a steel tube is formed. Each casing section has complementary interlocking structure running its length that interlocks with complementary interlocking structure on the adjacent casing section. Thus, once the first tube is emplaced, placement of subsequent tubes is facilitated by the complementary interlocking structure on the adjacent, previously placed, casing sections.

Kostelnik, Kevin M. (Idaho Falls, ID); Kawamura, Hideki (Tokyo, JP); Richardson, John G. (Idaho Falls, ID); Noda, Masaru (Tokyo, JP)

2004-10-12T23:59:59.000Z

393

Advanced drilling systems study.  

Science Conference Proceedings (OSTI)

This report documents the results of a study of advanced drilling concepts conducted jointly for the Natural Gas Technology Branch and the Geothermal Division of the U.S. Department of Energy. A number of alternative rock cutting concepts and drilling systems are examined. The systems cover the range from current technology, through ongoing efforts in drilling research, to highly speculative concepts. Cutting mechanisms that induce stress mechanically, hydraulically, and thermally are included. All functions necessary to drill and case a well are considered. Capital and operating costs are estimated and performance requirements, based on comparisons of the costs for alternative systems to conventional drilling technology, are developed. A number of problems common to several alternatives and to current technology are identified and discussed.

Pierce, Kenneth G.; Livesay, Billy Joe; Finger, John Travis (Livesay Consultants, Encintas, CA)

1996-05-01T23:59:59.000Z

394

ADVANCED CUTTINGS TRANSPORT STUDY  

DOE Green Energy (OSTI)

This report includes a review of the progress made in ACTF Flow Loop development and research during 90 days pre-award period (May 15-July 14, 1999) and the following three months after the project approval date (July15-October 15, 1999) The report presents information on the following specific subjects; (a) Progress in Advanced Cuttings Transport Facility design and development, (b) Progress report on the research project ''Study of Flow of Synthetic Drilling Fluids Under Elevated Pressure and Temperature Conditions'', (c) Progress report on the research project ''Study of Cuttings Transport with Foam Under LPAT Conditions (Joint Project with TUDRP)'', (d) Progress report on the research project ''Study of Cuttings Transport with Aerated Muds Under LPAT Conditions (Joint Project with TUDRP)'', (e) Progress report on the research project ''Study of Foam Flow Behavior Under EPET Conditions'', (f) Progress report on the instrumentation tasks (Tasks 11 and 12) (g) Activities towards technology transfer and developing contacts with oil and service company members.

Ergun Kuru; Stefan Miska; Nicholas Takach; Kaveh Ashenayi; Gerald Kane; Len Volk; Mark Pickell; Evren Ozbayoglu; Barkim Demirdal; Paco Vieira; Affonso Lourenco

1999-10-15T23:59:59.000Z

395

Advanced Telemetry Data Capturing  

SciTech Connect

This project developed a new generation or advanced data capturing process specifically designed for use in future telemetry test systems at the Kansas City Plant (KCP). Although similar data capturing processes are performed both commercially and at other DOE weapon facilities, the equipment used is not specifically designed to perform acceptance testing requirements unique to the KCP. Commercially available equipment, despite very high cost (up to $125,000), is deficient in reliability and long-term maintainability necessary in test systems at this facility. There are no commercial sources for some requirements, specifically Terminal Data Analyzer (TDA) data processing. Although other custom processes have been developed to satisfy these test requirements, these designs have become difficult to maintain and upgrade.

Paschke, G.A.

2000-05-16T23:59:59.000Z

396

Advancing Residential Energy Retrofits  

Science Conference Proceedings (OSTI)

To advance the market penetration of residential retrofits, Oak Ridge National Laboratory (ORNL) and Southface Energy Institute (Southface) partnered to provide technical assistance on nine home energy retrofits in metropolitan Atlanta with simulated source energy savings of 30% to 50%. Retrofit measures included duct sealing, air infiltration reductions, attic sealing and roofline insulation, crawlspace sealing, HVAC and water heating equipment replacement, and lighting and appliance upgrades. This paper will present a summary of these measures and their associated impacts on important home performance metrics, such as air infiltration and duct leakage. The average estimated source energy savings for the homes is 33%, and the actual heating season average savings is 32%. Additionally, a case study describing expected and realized energy savings of completed retrofit measures of one of the homes is described in this paper.

Jackson, Roderick K [ORNL; Boudreaux, Philip R [ORNL; Kim, Eyu-Jin [Southface Energy Institute; Roberts, Sydney [Southface Energy Institute

2012-01-01T23:59:59.000Z

397

Retractable pin dual in-line package test clip  

DOE Patents (OSTI)

This invention is a Dual In-Line Package (DIP) test clip for use when troubleshooting circuits containing DIP integrated circuits. This test clip is a significant improvement over existing DIP test clips in that it has retractable pins which will permit troubleshooting without risk of accidentally shorting adjacent pins together when moving probes to different pins on energized circuits or when the probe is accidentally bumped while taking measurements.

Bandzuch, Gregory S. (Washington, PA); Kosslow, William J. (Jefferson Boro, PA)

1996-01-01T23:59:59.000Z

398

Advanced Manufacturing Office: Motor Systems  

NLE Websites -- All DOE Office Websites (Extended Search)

Motor Systems to Motor Systems to someone by E-mail Share Advanced Manufacturing Office: Motor Systems on Facebook Tweet about Advanced Manufacturing Office: Motor Systems on Twitter Bookmark Advanced Manufacturing Office: Motor Systems on Google Bookmark Advanced Manufacturing Office: Motor Systems on Delicious Rank Advanced Manufacturing Office: Motor Systems on Digg Find More places to share Advanced Manufacturing Office: Motor Systems on AddThis.com... Quick Links Energy Resource Center Technical Publications by Energy System Energy-Efficient Technologies Incentives & Resources by Zip Code Better Plants Superior Energy Performance Contacts Motor Systems Photo of Man Checking Motor Performance Motor-driven equipment accounts for 54% of manufacturing electricity use. Dramatic energy and cost savings can be achieved in motor systems by

399

Dual Environment Effects on the Oxidation of Metallic Interconnects  

DOE Green Energy (OSTI)

Metallic interconnects in solid oxide fuel cells are exposed to a dual environment: fuel on one side (i.e. H2 gas) and oxidizer on the other side (i.e. air). It has been observed that the oxidation behavior of thin stainless steel sheet in air is changed by the presence of H2 on the other side of the sheet. The resulting dual environment scales are flaky and more friable than the single environment scales. The H2 disrupts the scale on the air-side. A model to explain some of the effects of a dual environment is presented where hydrogen diffusing through the stainless steel sheet reacts with oxygen diffusing through the scale to form water vapor, which has sufficient vapor pressure to mechanically disrupt the scale. Experiments on preoxidized 316L stainless steel tubing exposed to air/air, H2/air, and H2/Ar environments are reported in support of the model.

Holcomb, Gordon R.; Ziomek-Moroz, Malgorzata; Cramer, Stephen D.; Covino, Jr., Bernard S.; and Bullard, Sophie J.

2004-10-20T23:59:59.000Z

400

Advanced Distribution Automation Technical Assessments  

Science Conference Proceedings (OSTI)

This 2008 progress report on advanced distribution technical assessments focused on the International Electrotechnical Commission (IEC) TC-57 body of standards.

2008-12-19T23:59:59.000Z

Note: This page contains sample records for the topic "advanced sequential dual" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


401

Advanced Coal Conversion Process Demonstration  

NLE Websites -- All DOE Office Websites (Extended Search)

Clean Coal Technology Program Advanced Coal Conversion Process Demonstration A DOE Assessment DOENETL-20051217 U.S. Department of Energy Office of Fossil Energy National Energy...

402

Video Library | Advanced Photon Source  

NLE Websites -- All DOE Office Websites (Extended Search)

Archives APS Brochure Annual Reports Posters Podcasts Image Gallery external site Video Library Syndicated Feeds (RSS) Now Playing: The Advanced Photon Source More videos:...

403

Video Library | Advanced Photon Source  

NLE Websites -- All DOE Office Websites (Extended Search)

Video Library Related Links: APS Colloquium APS Podcasts APS Today More videos: Introduction to the APS Physics of the Blues Now Playing: Building the Advanced Photon Source This...

404

Systems Engineering Advancement Research Initiative  

E-Print Network (OSTI)

strategic partners Define and research fundamental concepts for advanced system engineering Contribute materials, and handbooks to inspire, inform, and guide students and practitioners VENUE SEAri is located

de Weck, Olivier L.

405

User Information | Advanced Photon Source  

NLE Websites -- All DOE Office Websites (Extended Search)

User Information The Advanced Photon Source provides a variety of guides, resources, and information for prospective, new, and current users. In this section: For Prospective Users...

406

Avoid advanced control project mistakes  

Science Conference Proceedings (OSTI)

On-line process optimization is worth working for but without robust advanced controls it will never happen. In this paper, the author evaluates how well advanced controls worked in five refineries. Having spent money on such projects, the refineries faced a situation in which there was no measurable improvement in overall plant performance. These refineries are owned by different companies, yet they share a pattern of mistakes in administrating advanced controls. Highlighting these mistakes shows ways to improve the organization of advanced control technology, to avoid obvious pitfalls.

Friedman, Y.Z. (Petrocontrol, Madison, NJ (United States))

1992-10-01T23:59:59.000Z

407

Advanced Application Development Program Information  

Energy.gov (U.S. Department of Energy (DOE))

Summary of the Tranmission Reliability program's Advanced Applications Research and Development activity area. This program develops and demonstrates tools to monitor and control the grid with...

408

Advanced Manufacturing Office: Information Resources  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

incentives, tools, and training to help companies of all sizes identify energy saving projects and chart a path toward continuous energy improvement. Advanced Manufacturing...

409

Advanced Materials Research Highlights | ORNL  

NLE Websites -- All DOE Office Websites (Extended Search)

Advanced Materials | Research Highlights Research Highlights 1-10 of 44 Results Prev 12345 Next Topotactic valence state control in epitaxial multivalent oxides July 17, 2013 -...

410

Advanced Cladding Materials for Fuels  

Science Conference Proceedings (OSTI)

Fuel Cycle Research and Development. Advanced Cladding Materials for. Fuels. Stuart A. Maloy. M. Nastasi, A. Misra. Los Alamos National Laboratory.

411

Media Center | Advanced Photon Source  

NLE Websites -- All DOE Office Websites (Extended Search)

impact on nearly every aspect of our lives. Annual Reports Articles on Advanced Photon Source research and engineering highlights that are written for the interested...

412

Information Technology | Advanced Photon Source  

NLE Websites -- All DOE Office Websites (Extended Search)

Advanced Photon Source Information Technology Support Search APS ... Search Button About User Information News & Events Science & Education Beamlines Divisions Argonne Home >...

413

Advanced Flow-Battery Systems  

Science Conference Proceedings (OSTI)

Presentation Title, Advanced Flow-Battery Systems ... Abstract Scope, Flow- battery systems (FBS) were originally developed over 30 years ago and have since...

414

Vulnerabilities in Advanced Metering Infrastructure.  

E-Print Network (OSTI)

??Smart grid has become a reality in the United States. Billions of dollars are being poured into deploying a major component, - the Advanced Metering (more)

Podkuiko, Dmitry

2012-01-01T23:59:59.000Z

415

CAT Communicator | Advanced Photon Source  

NLE Websites -- All DOE Office Websites (Extended Search)

Division XSD Groups Industry Argonne Home Advanced Photon Source News Archives CAT Communicator CAT Communicator was a newsletter intended to provide APS information to...

416

Participant Advance Information PLEASE PRINT!  

Science Conference Proceedings (OSTI)

... Hotel Workshop participants may select from a ... for a listing of area hotels: http://www ... of Education, Department of Energy's Advanced Manufacturing ...

2013-01-23T23:59:59.000Z

417

NREL: Advanced Power Electronics - Webmaster  

NLE Websites -- All DOE Office Websites (Extended Search)

Your name: Your email address: Your message: Send Message Printable Version Advanced Power Electronics Home About the Project Technology Basics Research & Development...

418

Extended Constant Power Speed Range of the Brushless DC Motor Through Dual Mode Inverter Control  

SciTech Connect

The trapezoidal back electromotive force (emf) brushless direct current (dc) motor (BDCM) with surface-mounted magnets has high-power density and efficiency especially when rare-earth magnet materials are used. Traction applications, such as electric vehicles, could benefit significantly from the use of such motors. Unfortunately, a practical means for driving the motor over a constant power speed ratio (CPSR) of 5:1 or more has not yet been developed. A key feature of these motors is that they have low internal inductance. The phase advance method is effective in controlling the motor power over such a speed range, but the current at high speed may be several times greater than that required at the base speed. The increase in current during high-speed operation is due to the low motor inductance and the action of the bypass diodes of the inverter. The use of such a control would require increased current rating of the inverter semiconductors and additional cooling for the inverter, where the conduction losses increase proportionally with current, and especially for the motor, where the losses increase with the square of the current. The high current problems of phase advance can be mitigated by adding series inductance; however, this reduces power density, requires significant increase in supply voltage, and leaves the CPSR performance of the system highly sensitive to variations in the available voltage. A new inverter topology and control scheme has been developed that can drive low-inductance BDCMs over the CPSR that would be required in electric vehicle applications. This new controller is called the dual-mode inverter control (DMIC). It is shown that the BDCM has an infinite CPSR when it is driven by the DMIC.

Lawler, J.S.

2000-06-23T23:59:59.000Z

419

Advanced Hydrogen Turbine Development  

DOE Green Energy (OSTI)

Siemens has developed a roadmap to achieve the DOE goals for efficiency, cost reduction, and emissions through innovative approaches and novel technologies which build upon worldwide IGCC operational experience, platform technology, and extensive experience in G-class operating conditions. In Phase 1, the technologies and concepts necessary to achieve the program goals were identified for the gas turbine components and supporting technology areas and testing plans were developed to mitigate identified risks. Multiple studies were conducted to evaluate the impact in plant performance of different gas turbine and plant technologies. 2015 gas turbine technologies showed a significant improvement in IGCC plant efficiency, however, a severe performance penalty was calculated for high carbon capture cases. Thermodynamic calculations showed that the DOE 2010 and 2015 efficiency targets can be met with a two step approach. A risk management process was instituted in Phase 1 to identify risk and develop mitigation plans. For the risks identified, testing and development programs are in place and the risks will be revisited periodically to determine if changes to the plan are necessary. A compressor performance prediction has shown that the design of the compressor for the engine can be achieved with additional stages added to the rear of the compressor. Tip clearance effects were studied as well as a range of flow and pressure ratios to evaluate the impacts to both performance and stability. Considerable data was obtained on the four candidate combustion systems: diffusion, catalytic, premix, and distributed combustion. Based on the results of Phase 1, the premixed combustion system and the distributed combustion system were chosen as having the most potential and will be the focus of Phase 2 of the program. Significant progress was also made in obtaining combustion kinetics data for high hydrogen fuels. The Phase 1 turbine studies indicate initial feasibility of the advanced hydrogen turbine that meets the aggressive targets set forth for the advanced hydrogen turbine, including increased rotor inlet temperature (RIT), lower total cooling and leakage air (TCLA) flow, higher pressure ratio, and higher mass flow through the turbine compared to the baseline. Maintaining efficiency with high mass flow Syngas combustion is achieved using a large high AN2 blade 4, which has been identified as a significant advancement beyond the current state-of-the-art. Preliminary results showed feasibility of a rotor system capable of increased power output and operating conditions above the baseline. In addition, several concepts were developed for casing components to address higher operating conditions. Rare earth modified bond coat for the purpose of reducing oxidation and TBC spallation demonstrated an increase in TBC spallation life of almost 40%. The results from Phase 1 identified two TBC compositions which satisfy the thermal conductivity requirements and have demonstrated phase stability up to temperatures of 1850 C. The potential to join alloys using a bonding process has been demonstrated and initial HVOF spray deposition trials were promising. The qualitative ranking of alloys and coatings in environmental conditions was also performed using isothermal tests where significant variations in alloy degradation were observed as a function of gas composition. Initial basic system configuration schematics and working system descriptions have been produced to define key boundary data and support estimation of costs. Review of existing materials in use for hydrogen transportation show benefits or tradeoffs for materials that could be used in this type of applications. Hydrogen safety will become a larger risk than when using natural gas fuel as the work done to date in other areas has shown direct implications for this type of use. Studies were conducted which showed reduced CO{sub 2} and NOx emissions with increased plant efficiency. An approach to maximize plant output is needed in order to address the DOE turbine goal for 20-30% reduction o

Joesph Fadok

2008-01-01T23:59:59.000Z

420

NETL: Pre-Combustion Carbon Dioxide Capture by a New Dual-Phase Ceramic  

NLE Websites -- All DOE Office Websites (Extended Search)

Pre-Combustion Carbon Dioxide Capture by a New Dual-Phase Ceramic Carbonate Membrane Reactor Pre-Combustion Carbon Dioxide Capture by a New Dual-Phase Ceramic Carbonate Membrane Reactor Project No.: DE-FE0000470 Arizona State University is developing a dual-phase, membrane-based separation device which will separate carbon dioxide (CO2) from typical water gas shift (WGS) mixture feeds and produce hydrogen, which can be introduced into the combustion turbines of integrated gasification combined cycle (IGCC) plants. The objectives of the project are experimental studies of the synthesis of a high-temperature, chemically and thermally stable and CO2 perm-selective dual-phase membrane and its use as a membrane reactor for WGS reaction to produce H2 and CO2 rich streams. Concept of ceramic-carbonate dual phase membranes for CO2 separation. Concept of ceramic-carbonate dual phase membranes for CO2 separation.

Note: This page contains sample records for the topic "advanced sequential dual" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


421

Advanced Light Source  

NLE Websites -- All DOE Office Websites (Extended Search)

Next >> Next >> Visitors Access to the ALS Gate Access guest-house Guest House lab-shuttles Lab Shuttles maps-and-directions Maps and Directions Parking Safety Safety for Users safety-for-staff Safety for Staff In Case of Emergency Resources Acronyms Multimedia Employment staff-intranet Staff Intranet Site Map Contact Digg: ALSBerkeleyLab Facebook Page: 208064938929 Flickr: advancedlightsource Twitter: ALSBerkeleyLab YouTube: AdvancedLightSource January 2014 Sun Mon Tue Wed Thu Fri Sat 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Recent Science Highlights Minding the Gap Makes for More Efficient Solar Cells Using novel materials to develop thin, flexible, and more efficient photovoltaic cells is one of the hottest topics in current materials research. A class of transition metals undergo a dramatic change that makes them ideal for solar energy applications.

422

ADVANCED CUTTINGS TRANSPORT STUDY  

SciTech Connect

This is the second quarterly progress report for Year 2 of the ACTS project. It includes a review of progress made in Flow Loop development and research during the period of time between Oct 1, 2000 and December 31, 2000. This report presents a review of progress on the following specific tasks: (a) Design and development of an Advanced Cuttings Transport Facility (Task 2: Addition of a foam generation and breaker system), (b) Research project (Task 6): ''Study of Cuttings Transport with Foam Under LPAT Conditions (Joint Project with TUDRP)'', (c) Research project (Task 7): ''Study of Cuttings Transport with Aerated Muds Under LPAT Conditions (Joint Project with TUDRP)'', (d) Research project (Task 8): ''Study of Flow of Synthetic Drilling Fluids Under Elevated Pressure and Temperature Conditions'', (e) Research project (Task 9): ''Study of Foam Flow Behavior Under EPET Conditions'', (f) Research project (Task 10): ''Study of Cuttings Transport with Aerated Mud Under Elevated Pressure and Temperature Conditions'', (g) Research on instrumentation tasks to measure: Cuttings concentration and distribution in a flowing slurry (Task 11), and Foam properties while transporting cuttings. (Task 12), (h) Development of a Safety program for the ACTS Flow Loop. Progress on a comprehensive safety review of all flow-loop components and operational procedures. (Task 1S). (i) Activities towards technology transfer and developing contacts with Petroleum and service company members, and increasing the number of JIP members. The tasks Completed During This Quarter are Task 7 and Task 8.

Troy Reed; Stefan Miska; Nicholas Takach; Kaveh Ashenayi; Gerald Kane; Mark Pickell; Len Volk; Mike Volk; Barkim Demirdal; Affonso Lourenco; Evren Ozbayoglu; Paco Vieira; Lei Zhou

2000-01-30T23:59:59.000Z

423

ADVANCED CUTTINGS TRANSPORT STUDY  

Science Conference Proceedings (OSTI)

This is the first quarterly progress report for Year 2 of the ACTS project. It includes a review of progress made in Flow Loop development and research during the period of time between July 14, 2000 and September 30, 2000. This report presents information on the following specific tasks: (a) Progress in Advanced Cuttings Transport Facility design and development (Task 2), (b) Progress on research project (Task 8): ''Study of Flow of Synthetic Drilling Fluids Under Elevated Pressure and Temperature Conditions'', (c) Progress on research project (Task 6): ''Study of Cuttings Transport with Foam Under LPAT Conditions (Joint Project with TUDRP)'', (d) Progress on research project (Task 7): ''Study of Cuttings Transport with Aerated Muds Under LPAT Conditions (Joint Project with TUDRP)'', (e) Progress on research project (Task 9): ''Study of Foam Flow Behavior Under EPET Conditions'', (f) Initiate research on project (Task 10): ''Study of Cuttings Transport with Aerated Mud Under Elevated Pressure and Temperature Conditions'', (g) Progress on instrumentation tasks to measure: Cuttings concentration and distribution (Tasks 11), and Foam properties (Task 12), (h) Initiate a comprehensive safety review of all flow-loop components and operational procedures. Since the previous Task 1 has been completed, we will now designate this new task as: (Task 1S). (i) Activities towards technology transfer and developing contacts with Petroleum and service company members, and increasing the number of JIP members.

Troy Reed; Stefan Miska; Nicholas Takach; Kaveh Ashenayi; Gerald Kane; Mark Pickell; Len Volk; Mike Volk; Barkim Demirdal; Affonso Lourenco; Evren Ozbayoglu; Paco Vieira

2000-10-30T23:59:59.000Z

424

ADVANCED CUTTINGS TRANSPORT STUDY  

SciTech Connect

This is the fourth quarterly progress report for Year-3 of the ACTS Project. It includes a review of progress made in: (1) Flow Loop construction and development and (2) research tasks during the period of time between April 1, 2002 and June 30, 2002. This report presents a review of progress on the following specific tasks: (a) Design and development of an Advanced Cuttings Transport Facility (Task 3: Addition of a Cuttings Injection/Separation System), (b) Research project (Task 6): ''Study of Cuttings Transport with Foam Under LPAT Conditions (Joint Project with TUDRP)''; (c) Research project (Task 9b): ''Study of Foam Flow Behavior Under EPET Conditions''; (d) Research project (Task 10): ''Study of Cuttings Transport with Aerated Mud Under Elevated Pressure and Temperature Conditions''; (e) Research on three instrumentation tasks to measure: Cuttings concentration and distribution in a flowing slurry (Task 11), Foam texture while transporting cuttings. (Task 12), and Viscosity of Foam under EPET (Task 9b); (f) Development of a Safety program for the ACTS Flow Loop. Progress on a comprehensive safety review of all flow-loop components and operational procedures. (Task 1S); (g) Activities towards technology transfer and developing contacts with Petroleum and service company members, and increasing the number of JIP members.

Troy Reed; Stefan Miska; Nicholas Takach; Kaveh Ashenayi; Mark Pickell; Len Volk; Mike Volk; Evren Ozbayoglu; Lei Zhou

2002-07-30T23:59:59.000Z

425

ADVANCED CUTTINGS TRANSPORT STUDY  

SciTech Connect

This is the second quarterly progress report for Year-4 of the ACTS Project. It includes a review of progress made in: (1) Flow Loop construction and development and (2) research tasks during the period of time between October 1, 2002 and December 30, 2002. This report presents a review of progress on the following specific tasks. (a) Design and development of an Advanced Cuttings Transport Facility Task 3: Addition of a Cuttings Injection/Separation System, Task 4: Addition of a Pipe Rotation System. (b) New research project (Task 9b): ''Development of a Foam Generator/Viscometer for Elevated Pressure and Elevated Temperature (EPET) Conditions''. (d) Research project (Task 10): ''Study of Cuttings Transport with Aerated Mud Under Elevated Pressure and Temperature Conditions''. (e) Research on three instrumentation tasks to measure: Cuttings concentration and distribution in a flowing slurry (Task 11), Foam texture while transporting cuttings. (Task 12), and Viscosity of Foam under EPET (Task 9b). (f) New Research project (Task 13): ''Study of Cuttings Transport with Foam under Elevated Pressure and Temperature Conditions''. (g) Development of a Safety program for the ACTS Flow Loop. Progress on a comprehensive safety review of all flow-loop components and operational procedures. (Task 1S). (h) Activities towards technology transfer and developing contacts with Petroleum and service company members, and increasing the number of JIP members.

Troy Reed; Stefan Miska; Nicholas Takach; Kaveh Ashenayi; Mark Pickell; Len Volk; Mike Volk; Lei Zhou; Zhu Chen; Crystal Redden; Aimee Washington

2003-01-30T23:59:59.000Z

426

ADVANCED CUTTINGS TRANSPORT STUDY  

Science Conference Proceedings (OSTI)

This is the third quarterly progress report for Year 3 of the ACTS Project. It includes a review of progress made in: (1) Flow Loop construction and development and (2) research tasks during the period of time between Jan. 1, 2002 and Mar. 31, 2002. This report presents a review of progress on the following specific tasks: (a) Design and development of an Advanced Cuttings Transport Facility (Task 3: Addition of a Cuttings Injection/Separation System), (b) Research project (Task 6): ''Study of Cuttings Transport with Foam Under LPAT Conditions (Joint Project with TUDRP)'', (c) Research project (Task 9b): ''Study of Foam Flow Behavior Under EPET Conditions'', (d) Research project (Task 10): ''Study of Cuttings Transport with Aerated Mud Under Elevated Pressure and Temperature Conditions'', (e) Research on three instrumentation tasks to measure: Cuttings concentration and distribution in a flowing slurry (Task 11), Foam texture while transporting cuttings. (Task 12), and Viscosity of Foam under EPET (Task 9b); (f) Development of a Safety program for the ACTS Flow Loop, progress on a comprehensive safety review of all flow-loop components and operational procedures. (Task 1S); and (g) Activities towards technology transfer and developing contacts with Petroleum and service company members, and increasing the number of JIP members.

Troy Reed; Stefan Miska; Nicholas Takach; Kaveh Ashenayi; Mark Pickell; Len Volk; Mike Volk; Evren Ozbayoglu; Lei Zhou

2002-04-30T23:59:59.000Z

427

ADVANCED CUTTINGS TRANSPORT STUDY  

Science Conference Proceedings (OSTI)

This is the second quarterly progress report for Year 3 of the ACTS project. It includes a review of progress made in: (1) Flow Loop development and (2) research tasks during the period of time between Oct 1, 2001 and Dec. 31, 2001. This report presents a review of progress on the following specific tasks: (a) Design and development of an Advanced Cuttings Transport Facility (Task 3: Addition of a Cuttings Injection/Collection System), (b) Research project (Task 6): ''Study of Cuttings Transport with Foam Under LPAT Conditions (Joint Project with TUDRP)'', (c) Research project (Task 9): ''Study of Foam Flow Behavior Under EPET Conditions'', (d) Research project (Task 10): ''Study of Cuttings Transport with Aerated Mud Under Elevated Pressure and Temperature Conditions'', (e) Research on instrumentation tasks to measure: Cuttings concentration and distribution in a flowing slurry (Task 11), and Foam properties while transporting cuttings. (Task 12), (f) Development of a Safety program for the ACTS Flow Loop. Progress on a comprehensive safety review of all flow-loop components and operational procedures. (Task 1S). (g) Activities towards technology transfer and developing contacts with Petroleum and service company members, and increasing the number of JIP members.

Troy Reed; Stefan Miska; Nicholas Takach; Kaveh Ashenayi; Gerald Kane; Mark Pickell; Len Volk; Mike Volk; Affonso Lourenco; Evren Ozbayoglu; Lei Zhou

2002-01-30T23:59:59.000Z

428

ADVANCED CUTTINGS TRANSPORT STUDY  

SciTech Connect

This is the first quarterly progress report for Year-4 of the ACTS Project. It includes a review of progress made in: (1) Flow Loop construction and development and (2) research tasks during the period of time between July 1, 2002 and Sept. 30, 2002. This report presents a review of progress on the following specific tasks: (a) Design and development of an Advanced Cuttings Transport Facility Task 3: Addition of a Cuttings Injection/Separation System, Task 4: Addition of a Pipe Rotation System, (b) New Research project (Task 9b): ''Development of a Foam Generator/Viscometer for Elevated Pressure and Elevated Temperature (EPET) Conditions'', (d) Research project (Task 10): ''Study of Cuttings Transport with Aerated Mud Under Elevated Pressure and Temperature Conditions'', (e) Research on three instrumentation tasks to measure: Cuttings concentration and distribution in a flowing slurry (Task 11), Foam texture while transporting cuttings (Task 12), Viscosity of Foam under EPET (Task 9b). (f) Development of a Safety program for the ACTS Flow Loop. Progress on a comprehensive safety review of all flow-loop components and operational procedures. (Task 1S). (g) Activities towards technology transfer and developing contacts with Petroleum and service company members, and increasing the number of JIP members.

Troy Reed; Stefan Miska; Nicholas Takach; Kaveh Ashenayi; Mark Pickell; Len Volk, Mike Volk; Lei Zhou; Zhu Chen; Crystal Redden; Aimee Washington

2002-10-30T23:59:59.000Z

429

Advanced Production Planning Models  

SciTech Connect

>This report describes the innovative modeling approach developed as a result of a 3-year Laboratory Directed Research and Development project. The overall goal of this project was to provide an effective suite of solvers for advanced production planning at facilities in the nuclear weapons complex (NWC). We focused our development activities on problems related to operations at the DOE's Pantex Plant. These types of scheduling problems appear in many contexts other than Pantex--both within the NWC (e.g., Neutron Generators) and in other commercial manufacturing settings. We successfully developed an innovative and effective solution strategy for these types of problems. We have tested this approach on actual data from Pantex, and from Org. 14000 (Neutron Generator production). This report focuses on the mathematical representation of the modeling approach and presents three representative studies using Pantex data. Results associated with the Neutron Generator facility will be published in a subsequent SAND report. The approach to task-based scheduling described here represents a significant addition to the literature for large-scale, realistic scheduling problems in a variety of production settings.

JONES,DEAN A.; LAWTON,CRAIG R.; KJELDGAARD,EDWIN A.; WRIGHT,STEPHEN TROY; TURNQUIST,MARK A.; NOZICK,LINDA K.; LIST,GEORGE F.

2000-12-01T23:59:59.000Z

430

ADVANCED HYBRID PARTICULATE COLLECTOR  

SciTech Connect

A new concept in particulate control, called an advanced hybrid particulate collector (AHPC), is being developed under funding from the US Department of Energy. The AHPC combines the best features of electrostatic precipitators (ESPs) and baghouses in an entirely novel manner. The AHPC concept combines fabric filtration and electrostatic precipitation in the same housing, providing major synergism between the two methods, both in the particulate collection step and in transfer of dust to the hopper. The AHPC provides ultrahigh collection efficiency, overcoming the problem of excessive fine-particle emissions with conventional ESPs, and solves the problem of reentrainment and recollection of dust in conventional baghouses. Phase I of the development effort consisted of design, construction, and testing of a 5.7-m{sup 3}/min (200-acfm) working AHPC model. Results from both 8-hour parametric tests and 100-hour proof-of-concept tests with two different coals demonstrated excellent operability and greater than 99.99% fine-particle collection efficiency.

Stanley J. Miller; Grant L. Schelkoph; Grant E. Dunham

2000-12-01T23:59:59.000Z

431

Independent control of the shape and composition of ionic nanocrystals through sequential cation exchange reactions  

Science Conference Proceedings (OSTI)

Size- and shape-controlled nanocrystal growth is intensely researched for applications including electro-optic, catalytic, and medical devices. Chemical transformations such as cation exchange overcome the limitation of traditional colloidal synthesis, where the nanocrystal shape often reflects the inherent symmetry of the underlying lattice. Here we show that nanocrystals, with established synthetic protocols for high monodispersity, can be templates for independent composition control. Specifically, controlled interconversion between wurtzite CdS, chalcocite Cu2S, and rock salt PbS occurs while preserving the anisotropic dimensions unique to the as-synthesized materials. Sequential exchange reactions between the three sulfide compositions are driven by the disparate solubilites of the metal ion exchange pair in specific coordinating molecules. Starting with CdS, highly anisotropic PbS nanorods are created, which serve as an important material for studying strong 2-dimensional quantum confinement, as well as for optoelectronic applications. Furthermore, interesting nanoheterostructures of CdS|PbS are obtained by precise control over ion insertion and removal.

Luther, Joseph Matthew; Zheng, Haimei; Sadtler, Bryce; Alivisatos, A. Paul

2009-07-06T23:59:59.000Z

432

The Sequential Empirical Bayes Method: An Adaptive Constrained-Curve Fitting Algorithm for Lattice QCD  

E-Print Network (OSTI)

We introduce the ``Sequential Empirical Bayes Method'', an adaptive constrained-curve fitting procedure for extracting reliable priors. These are then used in standard augmented-$\\chi^2$ fits on separate data. This better stabilizes fits to lattice QCD overlap-fermion data at very low quark mass where {\\it a priori} values are not otherwise known. Lessons learned (including caveats limiting the scope of the method) from studying artificial data are presented. As an illustration, from local-local two-point correlation functions, we obtain masses and spectral weights for ground and first-excited states of the pion, give preliminary fits for the $a_0$ where ghost states (a quenched artifact) must be dealt with, and elaborate on the details of fits of the Roper resonance and $S_{11}(N^{1/2-})$ previously presented elsewhere. The data are from overlap fermions on a quenched $16^3\\times 28$ lattice with spatial size $La=3.2 {\\rm fm}$ and pion mass as low as $\\sim 180 {\\rm MeV}$.

Ying Chen; Shao-Jing Dong; Terrence Draper; Ivan Horvath; Keh-Fei Liu; Nilmani Mathur; Sonali Tamhankar; Cidambi Srinivasan; Frank X. Lee; Jianbo Zhang

2004-05-03T23:59:59.000Z

433

+44(0)1612756353. An Analytical Model for Sequential Investment Opportunities  

E-Print Network (OSTI)

We provide an analytical solution for American perpetual compound options, that do not rely on a bivariate or multivariate distribution function. This model is especially applicable for a real sequential investment opportunity, such as a series of drug development, tests and clinical trials, where the project can be cancelled at any time, and where the probability of failure declines over stages of completion. The effect of changing input parameter values can clearly be seen in terms of resulting overall project process volatility, and the effective mark-up factor which justifies continuing with each investment stage. In the base case, the effective markup factor increases as the stage nears completion if the project failure declines, although the absolute threshold of the project value less the remaining stage investment costs declines. This is consistent with the effect of decreases in project value volatility. Other results are not always intuitive, with different signed vegas and chis for different investment stages and degrees of moneyness. This study appears to be a unique approach, which yields the threshold project value relative to investment costs that justifies investment at each stage, with no timing restrictions. 2 1

Roger Adkins; We Thank Alcino Azevedo; Xianzhi Cao; Michael Flanagan; Afzal Siddiqui; Sigbjrn Sdal

2013-01-01T23:59:59.000Z

434

Mitofusins and OPA1 mediate sequential steps in mitochondrial membrane fusion  

E-Print Network (OSTI)

Mitochondrial fusion requires the coordinated fusion of the outer and inner membranes. Three large GTPasesOPA1 and the mitofusins Mfn1 and Mfn2are essential for the fusion of mammalian mitochondria. OPA1 is mutated in dominant optic atrophy, a neurodegenerative disease of the optic nerve. In yeast, the OPA1 ortholog Mgm1 is required for inner membrane fusion in vitro; nevertheless, yeast lacking Mgm1 show neither outer nor inner membrane fusion in vivo, because of the tight coupling between these two processes. We find that outer membrane fusion can be readily visualized in OPA1-null mouse cells in vivo, but these events do not progress to inner membrane fusion. Similar defects are found in cells lacking prohibitins, which are required for proper OPA1 processing. In contrast, double Mfn-null cells show neither outer nor inner membrane fusion. Mitochondria in OPA1-null cells often contain multiple matrix compartments bounded together by a single outer membrane, consistent with uncoupling of outer versus inner membrane fusion. In addition, unlike mitofusins and yeast Mgm1, OPA1 is not required on adjacent mitochondria to mediate membrane fusion. These results indicate that mammalian mitofusins and OPA1 mediate distinct sequential fusion steps that are readily uncoupled, in contrast to the situation in yeast.

Zhiyin Song; Mariam Ghochani; J. Michael Mccaffery; Terrence G. Frey; David C. Chan; Janet M. Shaw

2009-01-01T23:59:59.000Z

435

Expert system for identification of simultaneous and sequential reactor fuel failures with gas tagging  

DOE Patents (OSTI)

Failure of a fuel element in a nuclear reactor core is determined by a gas tagging failure detection system and method. Failures are catalogued and characterized after the event so that samples of the reactor's cover gas are taken at regular intervals and analyzed by mass spectroscopy. Employing a first set of systematic heuristic rules which are applied in a transformed node space allows the number of node combinations which must be processed within a barycentric algorithm to be substantially reduced. A second set of heuristic rules treats the tag nodes of the most recent one or two leakers as background'' gases, further reducing the number of trial node combinations. Lastly, a fuzzy'' set theory formalism minimizes experimental uncertainties in the identification of the most likely volumes of tag gases. This approach allows for the identification of virtually any number of sequential leaks and up to five simultaneous gas leaks from fuel elements. 14 figs.

Gross, K.C.

1994-07-26T23:59:59.000Z

436

Rerouting in advance reservation networks  

Science Conference Proceedings (OSTI)

The advance reservation of network connections is an area of growing interest and a range of service models and algorithms have been proposed to achieve various scheduling objectives, i.e., including optimization-based strategies and heuristic schemes. ... Keywords: Advance reservation, Bandwidth migration, Load-balancing, Rerouting

Chongyang Xie; Hamed Alazemi; Nasir Ghani

2012-07-01T23:59:59.000Z

437

Dual formulations of non-abelian spin models: local representation and low-temperature asymptotics  

E-Print Network (OSTI)

Non-abelian lattice spin models with symmetry group SU(N) or U(N) can be formulated in terms of link variables which are subject to the Bianchi constraints. Using this representation we derive exact and local dual formulation for the partition function of such models on a cubic lattice in arbitrary dimension D. Locality means that the dual action is given by a sum over some subset of hypercubes of the dual lattice and the interaction between dual variables ranges over one given hypercube. Dual variables are in general discrete-valued and live on (D-2)-cell of the dual lattice, in close analogy with the XY model. We use our construction to study in details the dual of SU(2) principal chiral model in two dimensions. We give dual expressions also for two-point correlation function in arbitrary representation and for the free energy of defects. Leading terms of the asymptotic expansion of the dual Boltzmann factor are computed and it is proven that at low temperatures it converges to a certain Gaussian distribution uniformly in all fluctuations of dual variables. This result enables us to define the semiclassical limit of the dual formulation and to determine an analog of the vortex--spin-wave representation for the partition function. Such representation is used to extract leading perturbative contribution to the correlation function which shows power-like decay at weak coupling. We also present some analytical evidences that the low-temperature limit of the dual formulation is completely described by ISO(2)-like approximation of SU(2) matrix elements.

O. Borisenko; V. Kushnir

2004-12-27T23:59:59.000Z

438

A new warmstarting strategy for the primal-dual column generation ...  

E-Print Network (OSTI)

Jun 24, 2012 ... Abstract: This paper presents a new warmstarting technique in the context of a primal-dual column generation method applied to solve a...

439

Optimization Online - A Primal-Dual Algorithm for Computing a Cost ...  

E-Print Network (OSTI)

Oct 23, 2011 ... A Primal-Dual Algorithm for Computing a Cost Allocation in the Core of Economic Lot-Sizing Games. Mohan Gopaladesikan (mohang ***at***...

440

Local Analysis of the Feasible Primal-Dual Interior-Point Method R ...  

E-Print Network (OSTI)

R. Silva ?. J. Soares . L. N. Vicente . Abstract. In this paper we analyze the rate of local convergence of the Newton primal-dual interior- point method when...

Note: This page contains sample records for the topic "advanced sequential dual" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


441

Primal-dual algorithms and infinite-dimensional Jordan algebras of ...  

E-Print Network (OSTI)

Mar 31, 2003 ... Primal-dual algorithms and infinite-dimensional Jordan algebras of finite ... of the technique of finite-dimensional Euclidean Jordan algebras to...

442

Dual Fuel Conversion System for Diesel Engines: Inventions and Innovation Project Fact Sheet  

DOE Green Energy (OSTI)

Project fact sheet written for the Inventions and Innovation Program about a new dual fuel conversion system allows diesel fuel switching with clean burning natural gas.

Wogsland, J.

2001-01-25T23:59:59.000Z

443

ADVANCED MIXING MODELS  

SciTech Connect

The process of recovering the waste in storage tanks at the Savannah River Site (SRS) typically requires mixing the contents of the tank with one to four dual-nozzle jet mixers located within the tank. The typical criteria to establish a mixed condition in a tank are based on the number of pumps in operation and the time duration of operation. To ensure that a mixed condition is achieved, operating times are set conservatively long. This approach results in high operational costs because of the long mixing times and high maintenance and repair costs for the same reason. A significant reduction in both of these costs might be realized by reducing the required mixing time based on calculating a reliable indicator of mixing with a suitably validated computer code. The work described in this report establishes the basis for further development of the theory leading to the identified mixing indicators, the benchmark analyses demonstrating their consistency with widely accepted correlations, and the application of those indicators to SRS waste tanks to provide a better, physically based estimate of the required mixing time. Waste storage tanks at SRS contain settled sludge which varies in height from zero to 10 ft. The sludge has been characterized and modeled as micron-sized solids, typically 1 to 5 microns, at weight fractions as high as 20 to 30 wt%, specific gravities to 1.4, and viscosities up to 64 cp during motion. The sludge is suspended and mixed through the use of submersible slurry jet pumps. To suspend settled sludge, water is added to the tank as a slurry medium and stirred with the jet pump. Although there is considerable technical literature on mixing and solid suspension in agitated tanks, very little literature has been published on jet mixing in a large-scale tank. If shorter mixing times can be shown to support Defense Waste Processing Facility (DWPF) or other feed requirements, longer pump lifetimes can be achieved with associated operational cost and schedule savings. The focus of the present work is to establish mixing criteria associated with the waste processing at SRS and to quantify the mixing time required to suspend sludge particles with the submersible jet pump. Literature results for a turbulent jet flow are reviewed briefly, since the decay of the axial jet velocity and the evolution of the jet flow patterns are important phenomena affecting sludge suspension and mixing operations. One of the main objectives in the waste processing is to provide the DWPF a uniform slurry composition at a certain weight percentage (typically {approx}13 wt%) over an extended period of time. In preparation of the sludge for slurrying to DWPF, several important questions have been raised with regard to sludge suspension and mixing of the solid suspension in the bulk of the tank: (1) How much time is required to prepare a slurry with a uniform solid composition for DWPF? (2) How long will it take to suspend and mix the sludge for uniform composition in any particular waste tank? (3) What are good mixing indicators to answer the questions concerning sludge mixing stated above in a general fashion applicable to any waste tank/slurry pump geometry and fluid/sludge combination? Grenville and Tilton (1996) investigated the mixing process by giving a pulse of tracer (electrolyte) through the submersible jet nozzle and by monitoring the conductivity at three locations within the cylindrical tank. They proposed that the mixing process was controlled by the turbulent kinetic energy dissipation rate in the region far away from the jet entrance. They took the energy dissipation rates in the regions remote from the nozzle to be proportional to jet velocity and jet diameter at that location. The reduction in the jet velocity was taken to be proportional to the nozzle velocity and distance from the nozzle. Based on their analysis, a correlation was proposed. The proposed correlation was shown to be valid over a wide range of Reynolds numbers (50,000 to 300,000) with a relative standard deviation of {+-} 11.83%. An improved correlat

Lee, S; Richard Dimenna, R; David Tamburello, D

2008-11-13T23:59:59.000Z

444

Advanced Powertrain Research Facility  

NLE Websites -- All DOE Office Websites (Extended Search)

95F 95F Vehicle Setup Information Vehicle architecture PHEV Test cell location Front Advanced Powertrain Research Facility Document date 10/18/2013 Vehicle dynamometer Input Revision Number 1 Test weight [lb] 3518 Notes: Target A [lb] 21.47 Target B [lb/mph] 0.21588 Target C [lb/mph^2] 0.012508 Test Fuel Information Revision Number 1 Test weight [lb] 3518 Test Fuel Information Fuel type EPA Tier II EEE HF0437 Fuel density [g/ml] 0.742 Fuel Net HV [BTU/lbm] 18475 Fuel type EPA Tier II EEE HF0437 T e s t I D [ # ] C y c l e C o l d s t a r t ( C S t ) H o t s t a r t [ H S t ] D a t e T e s t C e l l T e m p [ C ] T e s t C e l l R H [ % ] T e s t C e l l B a r o [ i n / H g ] V e h i c l e c o o l i n g f a n s p e e d : S p e e d M a t c h [ S M ] o r c o n s t a n t s p e e d [ C S ] S o l a r L a m p s [ W / m 2 ] V e i c l e C l i m a t e C o n t r o l s e t t i n g s H o o d P o s i t i o n [ U p ] o r [ C l o s e d ] W i n d o w P o s i t i o n [ C l o s e d ] o r [ D o w n ] C y

445

ADVANCED TURBINE SYSTEMS PROGRAM  

Science Conference Proceedings (OSTI)

The market for power generation equipment is undergoing a tremendous transformation. The traditional electric utility industry is restructuring, promising new opportunities and challenges for all facilities to meet their demands for electric and thermal energy. Now more than ever, facilities have a host of options to choose from, including new distributed generation (DG) technologies that are entering the market as well as existing DG options that are improving in cost and performance. The market is beginning to recognize that some of these users have needs beyond traditional grid-based power. Together, these changes are motivating commercial and industrial facilities to re-evaluate their current mix of energy services. One of the emerging generating options is a new breed of advanced fuel cells. While there are a variety of fuel cell technologies being developed, the solid oxide fuel cells (SOFC) and molten carbonate fuel cells (MCFC) are especially promising, with their electric efficiency expected around 50-60 percent and their ability to generate either hot water or high quality steam. In addition, they both have the attractive characteristics of all fuel cells--relatively small siting footprint, rapid response to changing loads, very low emissions, quiet operation, and an inherently modular design lending itself to capacity expansion at predictable unit cost with reasonably short lead times. The objectives of this project are to:(1) Estimate the market potential for high efficiency fuel cell hybrids in the U.S.;(2) Segment market size by commercial, industrial, and other key markets;(3) Identify and evaluate potential early adopters; and(4) Develop results that will help prioritize and target future R&D investments. The study focuses on high efficiency MCFC- and SOFC-based hybrids and competing systems such as gas turbines, reciprocating engines, fuel cells and traditional grid service. Specific regions in the country have been identified where these technologies and the corresponding early adopters are likely to be located.

Sy Ali

2002-03-01T23:59:59.000Z

446

State Technologies Advancement Collaborative  

DOE Green Energy (OSTI)

The U. S. Department of Energy (DOE), National Association of State Energy Officials (NASEO), and Association of State Energy Research and Technology Transfer Institutions (ASERTTI) signed an intergovernmental agreement on November 14, 2002, that allowed states and territories and the Federal Government to better collaborate on energy research, development, demonstration and deployment (RDD&D) projects. The agreement established the State Technologies Advancement Collaborative (STAC) which allowed the states and DOE to move RDD&D forward using an innovative competitive project selection and funding process. A cooperative agreement between DOE and NASEO served as the contracting instrument for this innovative federal-state partnership obligating funds from DOE's Office of Energy Efficiency and Renewable Energy and Office of Fossil Energy to plan, fund, and implement RDD&D projects that were consistent with the common priorities of the states and DOE. DOE's Golden Field Office provided Federal oversight and guidance for the STAC cooperative agreement. The STAC program was built on the foundation of prior Federal-State efforts to collaborate on and engage in joint planning for RDD&D. Although STAC builds on existing, successful programs, it is important to note that it was not intended to replace other successful joint DOE/State initiatives such as the State Energy Program or EERE Special Projects. Overall the STAC process was used to fund, through three competitive solicitations, 35 successful multi-state research, development, deployment, and demonstration projects with an overall average non-federal cost share of 43%. Twenty-two states were awarded at least one prime contract, and organizations in all 50 states and some territories were involved as subcontractors in at least one STAC project. Projects were funded in seven program areas: (1) Building Technologies, (2) Industrial Technologies, (3) Transportation Technologies, (4) Distributed Energy Resources, (5) Hydrogen Technology Learning Centers, (6) Fossil Energy, and (7) Rebuild America.

David S. Terry

2012-01-30T23:59:59.000Z

447

Advanced Geothermal Turbodrill  

DOE Green Energy (OSTI)

Approximately 50% of the cost of a new geothermal power plant is in the wells that must be drilled. Compared to the majority of oil and gas wells, geothermal wells are more difficult and costly to drill for several reasons. First, most U.S. geothermal resources consist of hot, hard crystalline rock formations which drill much slower than the relatively soft sedimentary formations associated with most oil and gas production. Second, high downhole temperatures can greatly shorten equipment life or preclude the use of some technologies altogether. Third, producing viable levels of electricity from geothermal fields requires the use of large diameter bores and a high degree of fluid communication, both of which increase drilling and completion costs. Optimizing fluid communication often requires creation of a directional well to intersect the best and largest number of fracture capable of producing hot geothermal fluids. Moineau motor stators made with elastomers cannot operate at geothermal temperatures, so they are limited to the upper portion of the hole. To overcome these limitations, Maurer Engineering Inc. (MEI) has developed a turbodrill that does not use elastomers and therefore can operate at geothermal temperatures. This new turbodrill uses a special gear assembly to reduce the output speed, thus allowing a larger range of bit types, especially tri-cone roller bits, which are the bits of choice for drilling hard crystalline formations. The Advanced Geothermal Turbodrill (AGT) represents a significant improvement for drilling geothermal wells and has the potential to significantly reduce drilling costs while increasing production, thereby making geothermal energy less expensive and better able to compete with fossil fuels. The final field test of the AGT will prepare the tool for successful commercialization.

W. C. Maurer

2000-05-01T23:59:59.000Z

448

Progress Report for Advanced Automotive Fuels  

Alternative Fuels and Advanced Vehicles Data Center (EERE)

Energy Energy Office of Advanced Automotive Technologies 1000 Independence Avenue, S.W. Washington, DC 20585-0121 FY 1999 FY 1999 FY 1999 FY 1999 Progress Report for Advanced Automotive Fuels Progress Report for Advanced Automotive Fuels Progress Report for Advanced Automotive Fuels Progress Report for Advanced Automotive Fuels Energy Efficiency and Renewable Energy Energy Efficiency and Renewable Energy Energy Efficiency and Renewable Energy Energy Efficiency and Renewable Energy Office of Transportation Technologies Office of Transportation Technologies Office of Transportation Technologies Office of Transportation Technologies Office of Advanced Automotive Technologies Office of Advanced Automotive Technologies Office of Advanced Automotive Technologies Office of Advanced Automotive Technologies

449

Market Assessment of Retrofit Dual-Fuel Diesel Generators  

Science Conference Proceedings (OSTI)

Reciprocating engines have long played an important role in the distributed resources market and should continue to provide end-use customers and energy companies benefits in both on-site and grid-connected power generation service. This report presents results of collaborative technical and economic market analyses with a major engine manufacturer to examine the prospects for conversion of existing diesel generators in the 500-2000 kW size range to dual-fuel (natural gas and diesel fuel) operation. Thes...

2001-11-30T23:59:59.000Z

450

Dual wavelength laser damage testing for high energy lasers.  

Science Conference Proceedings (OSTI)

As high energy laser systems evolve towards higher energies, fundamental material properties such as the laser-induced damage threshold (LIDT) of the optics limit the overall system performance. The Z-Backlighter Laser Facility at Sandia National Laboratories uses a pair of such kiljoule-class Nd:Phosphate Glass lasers for x-ray radiography of high energy density physics events on the Z-Accelerator. These two systems, the Z-Beamlet system operating at 527nm/ 1ns and the Z-Petawatt system operating at 1054nm/ 0.5ps, can be combined for some experimental applications. In these scenarios, dichroic beam combining optics and subsequent dual wavelength high reflectors will see a high fluence from combined simultaneous laser exposure and may even see lingering effects when used for pump-probe configurations. Only recently have researchers begun to explore such concerns, looking at individual and simultaneous exposures of optics to 1064 and third harmonic 355nm light from Nd:YAG [1]. However, to our knowledge, measurements of simultaneous and delayed dual wavelength damage thresholds on such optics have not been performed for exposure to 1054nm and its second harmonic light, especially when the pulses are of disparate pulse duration. The Z-Backlighter Facility has an instrumented damage tester setup to examine the issues of laser-induced damage thresholds in a variety of such situations [2] . Using this damage tester, we have measured the LIDT of dual wavelength high reflectors at 1054nm/0.5ps and 532nm/7ns, separately and spatially combined, both co-temporal and delayed, with single and multiple exposures. We found that the LIDT of the sample at 1054nm/0.5ps can be significantly lowered, from 1.32J/cm{sup 2} damage fluence with 1054/0.5ps only to 1.05 J/cm{sup 2} with the simultaneous presence of 532nm/7ns laser light at a fluence of 8.1 J/cm{sup 2}. This reduction of LIDT of the sample at 1054nm/0.5ps continues as the fluence of 532nm/7ns laser light simultaneously present increases. The reduction of LIDT does not occur when the 2 pulses are temporally separated. This paper will also present dual wavelength LIDT results of commercial dichroic beam-combining optics simultaneously exposed with laser light at 1054nm/2.5ns and 532nm/7ns.

Atherton, Briggs W.; Rambo, Patrick K.; Schwarz, Jens; Kimmel, Mark W.

2010-05-01T23:59:59.000Z

451

DUAL PHASE MEMBRANE FOR HIGH TEMPERATURE CO2 SEPARATION  

SciTech Connect

This project is intended to expand upon the previous year's research en route to the development of a sustainable dual phase membrane for CO{sub 2} separation. It was found that the pores within the supports had to be less than 9 {micro}m in order to maintain the stability of the dual phase membrane. Pores larger than 9 {micro}m would be unable to hold the molten carbonate phase in place, rendering the membrane ineffective. Calculations show that 80% of the pore volume of the 0.5 media grade metal support was filled with the molten carbonate. Information obtained from EDS and SEM confirmed that the molten carbonate completely infiltrated the pores on both the contact and non-contact size of the metal support. Permeation tests for CO{sub 2} and N{sub 2} at 450-750 C show very low permeance of those two gases through the dual phase membrane, which was expected due to the lack of ionization of those two gases. Permeance of the CO{sub 2} and O{sub 2} mixture was much higher, indicating that the gases do form an ionic species, CO{sub 3}{sup 2-}, enhancing transport through the membrane. However, at temperatures in excess of 650 C, the permeance of CO{sub 3}{sup 2-} decreased quite rapidly, while predictions showed that permeance should have continued to increase. XRD data obtained form the surface of the membrane indicated the formation of lithium iron oxides on the support. This layer has a very low conductivity, which drastically reduces the flow of electrons to the CO{sub 2}/O{sub 2} gas mixture, limiting the formation of the ionic species. These results indicate that the use of stainless steel supports in a high temperature oxidative environment can lead to decreased performance of the membranes. This revelation has created the need for an oxidation resistant support, which can be gained by the use of a ceramic-type membrane. Future research efforts will be directed towards preparation of a new ceramic-carbonate dual phase membrane. The membrane will based on an oxide ceramic support that has an oxidation resistance better than the metal support and high electronic conductivity (1200-1500 S/cm) in the interested temperature range (400-600 C).

Jerry Y.S. Lin; Seungjoon Chung; Matthew Anderson

2005-12-01T23:59:59.000Z

452

Photoemission with Chemical Potential from QCD Gravity Dual  

E-Print Network (OSTI)

We consider a $D4-D8-\\bar D8$ brane construction which gives rise to a large N QCD at sufficiently small energies. Using the gravity dual of this system, we study chiral phase transition at finite chemical potential and temperature and find a line of first order phase transitions in the phase plane. We compute the spectral function and the photon emission rate. The trace of the spectral function is monotonic at vanishing chemical potential, but develops some interesting features as the value of the chemical potential is increased.

Andrei Parnachev; David A. Sahakyan

2006-10-23T23:59:59.000Z

453

Dual-circuit, multiple-effect refrigeration system and method  

DOE Patents (OSTI)

A dual circuit absorption refrigeration system comprising a high temperature single-effect refrigeration loop and a lower temperature double-effect refrigeration loop separate from one another and provided with a double-condenser coupling therebetween. The high temperature condenser of the single-effect refrigeration loop is double coupled to both of the generators in the double-effect refrigeration loop to improve internal heat recovery and a heat and mass transfer additive such as 2-ethyl-1-hexanol is used in the lower temperature double-effect refrigeration loop to improve the performance of the absorber in the double-effect refrigeration loop.

DeVault, Robert C. (Knoxville, TN)

1995-01-01T23:59:59.000Z

454

Gauge theories on hyperbolic spaces and dual wormhole instabilities  

Science Conference Proceedings (OSTI)

We study supergravity duals of strongly coupled four-dimensional gauge theories formulated on compact quotients of hyperbolic spaces. The resulting background geometries are represented by Euclidean wormholes, which complicate establishing the precise gauge theory/string theory correspondence dictionary. These backgrounds suffer from the nonperturbative instabilities arising from the D3D3-bar pair-production in the background four-form potential. We discuss conditions for suppressing this Schwingerlike instability. We find that Euclidean wormholes arising in this construction develop a naked singularity before they can be stabilized.

Buchel, Alex [Department of Applied Mathematics, University of Western Ontario, London, Ontario N6A 5B7 (Canada); Perimeter Institute for Theoretical Physics, Waterloo, Ontario N2J 2W9 (Canada)

2004-09-15T23:59:59.000Z

455

NETL: Advanced Research - The Advanced Research (AR) Program  

NLE Websites -- All DOE Office Websites (Extended Search)

AR Program AR Program Advanced Research The Advanced Research (AR) Program Advanced Research Program Diagram CLICK ON GRAPHIC TO ENLARGE CLICK ON GRAPHIC TO ENLARGE AR pursues projects in several key areas that are considered to be of greatest relevance and potential benefit to advanced coal and power systems. Many of AR's projects focus on "breakthrough" technologies or novel applications, striving to balance high risk against the prospect of high payoff in terms of measurable benefits to coal and power systems technologies - improved efficiencies, lower costs, new materials, and new processes. AR manages a portfolio that includes pre-commercial projects that rely on NETL's in-house facilities and depth of expertise, as well as collaborative external arrangements that draw upon diverse outside

456

Theoretical study of a localized quantum spin reversal by the sequential injection of spins in a spin quantum dot  

E-Print Network (OSTI)

This is a theoretical study of the reversal of a localized quantum spin induced by sequential injection of spins for a spin quantum dot that has a quantum spin. The system consists of ``electrode/quantum well(QW)/dot/QW/electrode" junctions, in which the left QW has an energy level of conduction electrons with only up-spin. We consider a situation in which up-spin electrons are sequentially injected from the left electrode into the dot through the QW and an exchange interaction acts between the electrons and the localized spin. To describe the sequentially injected electrons, we propose a simple method based on approximate solutions from the time-dependent Schr$\\ddot{\\rm o}$dinger equation. Using this method, it is shown that the spin reversal occurs when the right QW has energy levels of conduction electrons with only down-spin. In particular, the expression of the reversal time of a localized spin is derived and the upper and lower limits of the time are clearly expressed. This expression is expected to be useful for a rough estimation of the minimum relaxation time of the localized spin to achieve the reversal. We also obtain analytic expressions for the expectation value of the localized spin and the electrical current as a function of time. In addition, we found that a system with the non-magnetic right QW exhibits spin reversal or non-reversal depending on the exchange interaction.

Satoshi Kokado; Kazumasa Ueda; Kikuo Harigaya; Akimasa Sakuma

2007-08-10T23:59:59.000Z

457

ADVANCED STEAM GENERATORS  

SciTech Connect

Concerns about climate change have encouraged significant interest in concepts for ultra-low or ''zero''-emissions power generation systems. In some proposed concepts, nitrogen is removed from the combustion air and replaced with another diluent such as carbon dioxide or steam. In this way, formation of nitrogen oxides is prevented, and the exhaust stream can be separated into concentrated CO{sub 2} and steam or water streams. The concentrated CO{sub 2} stream could then serve as input to a CO{sub 2} sequestration process or utilized in some other way. Some of these concepts are illustrated in Figure 1. This project is an investigation of one approach to ''zero'' emission power generation. Oxy-fuel combustion is used with steam as diluent in a power cycle proposed by Clean Energy Systems, Inc. (CES) [1,2]. In oxy-fuel combustion, air separation is used to produce nearly pure oxygen for combustion. In this particular concept, the combustion temperatures are moderated by steam as a diluent. An advantage of this technique is that water in the product stream can be condensed with relative ease, leaving a pure CO{sub 2} stream suitable for sequestration. Because most of the atmospheric nitrogen has been separated from the oxidant, the potential to form any NOx pollutant is very small. Trace quantities of any minor pollutants species that do form are captured with the CO{sub 2} or can be readily removed from the condensate. The result is a nearly zero-emission power plant. A sketch of the turbine system proposed by CES is shown in Figure 2. NETL is working with CES to develop a reheat combustor for this application. The reheat combustion application is unusual even among oxy-fuel combustion applications. Most often, oxy-fuel combustion is carried out with the intent of producing very high temperatures for heat transfer to a product. In the reheat case, incoming steam is mixed with the oxygen and natural gas fuel to control the temperature of the output stream to about 1480 K. A potential concern is the possibility of quenching non-equilibrium levels of CO or unburned fuel in the mixing process. Inadequate residence times in the combustor and/or slow kinetics could possibly result in unacceptably high emissions. Thus, the reheat combustor design must balance the need for minimal excess oxygen with the need to oxidize the CO. This paper will describe the progress made to date in the design, fabrication, and simulation of a reheat combustor for an advanced steam generator system, and discuss planned experimental testing to be conducted in conjunction with NASA Glenn Research Center-Plumb Brook Station.

Richards, Geo. A.; Casleton, Kent H.; Lewis, Robie E.; Rogers, William A. (U.S. DOE National Energy Technology Laboratory); Woike, Mark R.; Willis; Brian P. (NASA Glenn Research Center)

2001-11-06T23:59:59.000Z

458

Advanced Process Heater  

SciTech Connect

The Roadmap for Process Heating Technology (March 16, 2001), identified the following priority R&D needs: Improved performance of high temperature materials; Improved methods for stabilizing low emission flames; Heating technologies that simultaneously reduce emissions, increase efficiency, and increase heat transfer. This Category I award entitled ''Proof of Concept of an Advanced Process Heater (APH) for Steel, Aluminum, and Petroleum Industries of the Future'' met the technical feasibility goals of: (1) Doubling the heat transfer rates (2) Improving thermal efficiencies by 20%, (3) Improving temperature uniformity by 100 degrees F and (4) simultaneously reducing NOx and CO2 emissions. The APH address EERE's mission priority of increasing efficiency/reducing fuel usage in energy intensive industries. One component of the APH, the SpyroCorTM, was commercialized by STORM Development's partner, Spinworks LLC. Over 2000 SpyrCorsTM were sold in 2004 resulting in 480 million BTU's of energy savings, 20% reduction in NOx and CO2 levels, and 9 jobs in N.W. Pennsylvania. A second component, the HeatCorTM, a low-cost high-temperature heat exchanger will be demonstrated by Spinworks in 2005 in preparation for commercial sales in 2006. The project occurred in the 21st Congressional District of Pennsylvania. Once fully commercialized, the APH energy savings potential is 339 trillion BTUs annually in the U.S. and will process 1.5 million more tons annually without major capital equipment expenditures. Spinworks will commercialize the APH and add over 100 U.S. workers. To accomplish the objective, STORM Development LLC teamed with Penn State University, SyCore, Inc, Spinworks LLC, and Schunk-INEX, Inc. The project consisted of component engineering and integration of the APH followed by parametric testing. All components of the system were tested in a lab furnace that simulates a full scale industrial installation. The target areas for development include: (1) Scale up STORM's Finned Stabilized Combustion, (2) Optimization of SyCore's SiGr Inserts such that the heat transfer on the exhaust leg will match the high luminosity burner leg., (3) Evaluation of the heat transfer characteristics of Schunk-INEX's finned composite tubes as a heat exchanger, and (4) Design of a system to monitor all components of the APH and control its performance such that the objectives are met.

Tom Briselden, Chris Parrish

2005-03-07T23:59:59.000Z

459

Method for enhancement of sequential hydraulic fracturing using control pulse fracturing  

Science Conference Proceedings (OSTI)

A method is described for creating multiple sequential hydraulic fractures via hydraulic fracturing combined with controlled pulse fracturing where two wells are utilized comprising: (a) drilling and completing a first and second well so that the wells will be in fluid communication with each other after subsequent fracturing in each well; (b) creating more than two simultaneous multiple vertical fractures via a controlled pulse fracturing method in the second well; (c) thereafter hydraulically fracturing the reservoir via the first well thereby creating fractures in the reservoir and afterwards shutting-in the first well without any induced pressure; (d) applying thereafter hydraulic pressure to the reservoir via the second well in an amount sufficient to fracture the reservoir thereby forming a first hydraulic fracture perpendicular to the least principal in-situ stress; (e) maintaining the hydraulic pressure on the reservoir while pumping via the second well alternate slugs of a thin-fluid spacer and a temporary blocking agent having a proppant therein whereupon a second hydraulic fracture is initiated; (f) maintaining the hydraulic pressure on the second well while pumping alternate slugs of spacer and blocking agent into the second hydraulic fracture thereby causing the second hydraulic fracture to propagate away from the first hydraulic fracture in step (e) in a curved trajectory which intersects a fracture created in the first well; (g) maintaining the hydraulic pressure while pumping as in step (f) whereupon another hydraulic fracture initiates causing another curved fracture trajectory to form and intersect the fracture created in the first well; and (h) repeated steps (f) and (g) until a desired number of hydraulic fractures are created which allows a substantial improvement in removing a natural resource from the reservoir.

Jennings, A.R. Jr.; Strubhar, M.K.

1993-07-20T23:59:59.000Z

460

Oil shale, tar sand, coal research advanced exploratory process technology, jointly sponsored research  

SciTech Connect

Accomplishments for the past quarter are presented for the following five tasks: oil shale; tar sand; coal; advanced exploratory process technology; and jointly sponsored research. Oil shale research covers oil shale process studies. Tar sand research is on process development of Recycle Oil Pyrolysis and Extraction (ROPE) Process. Coal research covers: coal combustion; integrated coal processing concepts; and solid waste management. Advanced exploratory process technology includes: advanced process concepts;advanced mitigation concepts; and oil and gas technology. Jointly sponsored research includes: organic and inorganic hazardous waste stabilization; CROW field demonstration with Bell Lumber and Pole; development and validation of a standard test method for sequential batch extraction fluid; PGI demonstration project; operation and evaluation of the CO[sub 2] HUFF-N-PUFF Process; fly ash binder for unsurfaced road aggregates; solid state NMR analysis of Mesaverde Group, Greater Green River Basin, tight gas sands; flow-loop testing of double-wall pipe for thermal applications; characterization of petroleum residue; shallow oil production using horizontal wells with enhanced oil recovery techniques; surface process study for oil recovery using a thermal extraction process; NMR analysis of samples from the ocean drilling program; in situ treatment of manufactured gas plant contaminated soils demonstration program; and solid state NMR analysis of naturally and artificially matured kerogens.

Speight, J.G.

1992-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "advanced sequential dual" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


461

Oil shale, tar sand, coal research, advanced exploratory process technology jointly sponsored research  

SciTech Connect

Accomplishments for the quarter are presented for the following areas of research: oil shale, tar sand, coal, advanced exploratory process technology, and jointly sponsored research. Oil shale research includes; oil shale process studies, environmental base studies for oil shale, and miscellaneous basic concept studies. Tar sand research covers process development. Coal research includes; underground coal gasification, coal combustion, integrated coal processing concepts, and solid waste management. Advanced exploratory process technology includes; advanced process concepts, advanced mitigation concepts, and oil and gas technology. Jointly sponsored research includes: organic and inorganic hazardous waste stabilization; development and validation of a standard test method for sequential batch extraction fluid; operation and evaluation of the CO[sub 2] HUFF-N-PUFF Process; fly ash binder for unsurfaced road aggregates; solid state NMR analysis of Mesa Verde Group, Greater Green River Basin, tight gas sands; flow-loop testing of double-wall pipe for thermal applications; characterization of petroleum residue; shallow oil production using horizontal wells with enhanced recovery techniques; and menu driven access to the WDEQ Hydrologic Data Management Systems.

1992-01-01T23:59:59.000Z

462

Ohio Advanced Energy Manufacturing Center  

Science Conference Proceedings (OSTI)

The program goal of the Ohio Advanced Energy Manufacturing Center (OAEMC) is to support advanced energy manufacturing and to create responsive manufacturing clusters that will support the production of advanced energy and energy-efficient products to help ensure the nation's energy and environmental security. This goal cuts across a number of existing industry segments critical to the nation's future. Many of the advanced energy businesses are starting to make the transition from technology development to commercial production. Historically, this transition from laboratory prototypes through initial production for early adopters to full production for mass markets has taken several years. Developing and implementing manufacturing technology to enable production at a price point the market will accept is a key step. Since these start-up operations are configured to advance the technology readiness of the core energy technology, they have neither the expertise nor the resources to address manufacturing readiness issues they encounter as the technology advances toward market entry. Given the economic realities of today's business environment, finding ways to accelerate this transition can make the difference between success and failure for a new product or business. The advanced energy industry touches a wide range of industry segments that are not accustomed to working together in complex supply chains to serve large markets such as automotive and construction. During its first three years, the Center has catalyzed the communication between companies and industry groups that serve the wide range of advanced energy markets. The Center has also found areas of common concern, and worked to help companies address these concerns on a segment or industry basis rather than having each company work to solve common problems individually. EWI worked with three industries through public-private partnerships to sew together disparate segments helping to promote overall industry health. To aid the overall advanced energy industry, EWI developed and launched an Ohio chapter of the non-profit Advanced Energy Economy. In this venture, Ohio joins with six other states including Colorado, Connecticut, Illinois, Maine, Massachusetts, New Hampshire, Rhode Island and Vermont to help promote technologies that deliver energy that is affordable, abundant and secure. In a more specific arena, EWI's advanced energy group collaborated with the EWI-run Nuclear Fabrication Consortium to promote the nuclear supply chain. Through this project EWI has helped bring the supply chain up to date for the upcoming period of construction, and assisted them in understanding the demands for the next generation of facilities now being designed. In a more targeted manner, EWI worked with 115 individual advanced energy companies that are attempting to bring new technology to market. First, these interactions helped EWI develop an awareness of issues common to companies in different advanced energy sectors. By identifying and addressing common issues, EWI helps companies bring technology to market sooner and at a lower cost. These visits also helped EWI develop a picture of industry capability. This helped EWI provide companies with contacts that can supply commercial solutions to their new product development challenges. By providing assistance in developing supply chain partnerships, EWI helped companies bring their technology to market faster and at a lower cost than they might have been able to do by themselves. Finally, at the most granular level EWI performed dedicated research and development on new manufacturing processes for advanced energy. During discussions with companies participating in advanced energy markets, several technology issues that cut across market segments were identified. To address some of these issues, three crosscutting technology development projects were initiated and completed with Center support. This included reversible welds for batteries and high temperature heat exchangers. It also included a novel advanced weld trainer that EWI

Kimberly Gibson; Mark Norfolk

2012-07-30T23:59:59.000Z

463

Advanced RNN Based NARMA Predictors  

Science Conference Proceedings (OSTI)

An analysis of nonlinear time series prediction schemes, realised though advanced Recurrent Neural Network (RNN) techniques is provided. Due to practical constraints in using common RNNs, such as the problem of vanishing gradient, some other ways to ...

Danilo P. Mandic; Jonathon A. Chambers

2000-08-01T23:59:59.000Z

464

Recent advances in kernel machines  

Science Conference Proceedings (OSTI)

This talk will review recent advances in the kernel methods focusing on support vector machines (SVM) for pattern recognition. Topics discussed include the kernel design issue through the multi kernel approach and the optimization issue with emphasis ...

Stphane Canu

2010-11-01T23:59:59.000Z

465

Ohio Advanced Energy Manufacturing Center  

SciTech Connect

The program goal of the Ohio Advanced Energy Manufacturing Center (OAEMC) is to support advanced energy manufacturing and to create responsive manufacturing clusters that will support the production of advanced energy and energy-efficient products to help ensure the nation's energy and environmental security. This goal cuts across a number of existing industry segments critical to the nation's future. Many of the advanced energy businesses are starting to make the transition from technology development to commercial production. Historically, this transition from laboratory prototypes through initial production for early adopters to full production for mass markets has taken several years. Developing and implementing manufacturing technology to enable production at a price point the market will accept is a key step. Since these start-up operations are configured to advance the technology readiness of the core energy technology, they have neither the expertise nor the resources to address manufacturing readiness issues they encounter as the technology advances toward market entry. Given the economic realities of today's business environment, finding ways to accelerate this transition can make the difference between success and failure for a new product or business. The advanced energy industry touches a wide range of industry segments that are not accustomed to working together in complex supply chains to serve large markets such as automotive and construction. During its first three years, the Center has catalyzed the communication between companies and industry groups that serve the wide range of advanced energy markets. The Center has also found areas of common concern, and worked to help companies address these concerns on a segment or industry basis rather than having each company work to solve common problems individually. EWI worked with three industries through public-private partnerships to sew together disparate segments helping to promote overall industry health. To aid the overall advanced energy industry, EWI developed and launched an Ohio chapter of the non-profit Advanced Energy Economy. In this venture, Ohio joins with six other states including Colorado, Connecticut, Illinois, Maine, Massachusetts, New Hampshire, Rhode Island and Vermont to help promote technologies that deliver energy that is affordable, abundant and secure. In a more specific arena, EWI's advanced energy group collaborated with the EWI-run Nuclear Fabrication Consortium to promote the nuclear supply chain. Through this project EWI has helped bring the supply chain up to date for the upcoming period of construction, and assisted them in understanding the demands for the next generation of facilities now being designed. In a more targeted manner, EWI worked with 115 individual advanced energy companies that are attempting to bring new technology to market. First, these interactions helped EWI develop an awareness of issues common to companies in different advanced energy sectors. By identifying and addressing common issues, EWI helps companies bring technology to market sooner and at a lower cost. These visits also helped EWI develop a picture of industry capability. This helped EWI provide companies with contacts that can supply commercial solutions to their new product development challenges. By providing assistance in developing supply chain partnerships, EWI helped companies bring their technology to market faster and at a lower cost than they might have been able to do by themselves. Finally, at the most granular level EWI performed dedicated research and development on new manufacturing processes for advanced energy. During discussions with companies participating in advanced energy markets, several technology issues that cut across market segments were identified. To address some of these issues, three crosscutting technology development projects were initiated and completed with Center support. This included reversible welds for batteries and high temperature heat exchangers. It also included a novel advanced weld trainer that EWI

Kimberly Gibson; Mark Norfolk

2012-07-30T23:59:59.000Z

466

Solar and wind power advancing  

U.S. Energy Information Administration (EIA) Indexed Site

Solar and wind power advancing U.S. electricity generation from wind and solar energy show no signs of slowing down. In its new monthly forecast, the U.S. Energy Information...

467

APS Upgrade | Advanced Photon Source  

NLE Websites -- All DOE Office Websites (Extended Search)

Workshop on new science opportunities provided by a multi-bend achromat lattice at the APS October 21-22 Advanced Photon Source Argonne National Lab To prepare for the workshop...

468

NETL: Advanced Research - Reference Shelf  

NLE Websites -- All DOE Office Websites (Extended Search)

(December 2012) Advanced Research Sensors and Controls Project Portfolio PDF-22MB (May 2011) Coal and Power Systems Strategic Plan and Multi-Year Program Plan PDF-1.7MB (Jan...

469

Advancements in nuclear waste assay.  

E-Print Network (OSTI)

??The research described in this thesis is directed at advancing the state of the practice of the non-destructive gamma-ray assay of nuclear waste containers. A (more)

Curtis, Deborah Claire

2008-01-01T23:59:59.000Z

470

DOE Patents Database - Advanced Search  

Office of Scientific and Technical Information (OSTI)

Advanced Search You may enter search criteria into one, or multiple fields. Use quotation marks for phrases. You may need to turn on Javascript in your browser to use this feature....

471

SERI advanced wind turbine blades  

DOE Green Energy (OSTI)

The primary goal of the Solar Energy Research Institute`s (SERI) advanced wind turbine blades is to convert the kinetic energy in the wind into mechanical energy in an inexpensive and efficient manner. To accomplish this goal, advanced wind turbine blades have been developed by SERI that utilize unique airfoil technology. Performance characteristics of the advanced blades were verified through atmospheric testing on fixed-pitch, stall-regulated horizontal-axis wind turbines (HAWTs). Of the various wind turbine configurations, the stall-regulated HAWT dominates the market because of its simplicity and low cost. Results of the atmospheric tests show that the SERI advanced blades produce 10% to 30% more energy than conventional blades. 6 refs.

Tangler, J.; Smith, B.; Jager, D.

1992-02-01T23:59:59.000Z

472

SERI advanced wind turbine blades  

DOE Green Energy (OSTI)

The primary goal of the Solar Energy Research Institute's (SERI) advanced wind turbine blades is to convert the kinetic energy in the wind into mechanical energy in an inexpensive and efficient manner. To accomplish this goal, advanced wind turbine blades have been developed by SERI that utilize unique airfoil technology. Performance characteristics of the advanced blades were verified through atmospheric testing on fixed-pitch, stall-regulated horizontal-axis wind turbines (HAWTs). Of the various wind turbine configurations, the stall-regulated HAWT dominates the market because of its simplicity and low cost. Results of the atmospheric tests show that the SERI advanced blades produce 10% to 30% more energy than conventional blades. 6 refs.

Tangler, J.; Smith, B.; Jager, D.

1992-02-01T23:59:59.000Z

473

Advanced Light Source Activity Report 2005  

E-Print Network (OSTI)

upgrade on the Advanced Light Source," Nucl. Instrum. Meth.n photoemission at the Advanced Light Source," Radit. Phys.high-pressure studies at the Advanced Light Source w i t h a

Tamura Ed., Lori S.

2010-01-01T23:59:59.000Z

474

Quasicrystals: Atomic coverings and windows are dual projects  

E-Print Network (OSTI)

In the window approach to quasicrystals, the atomic position space E_parallel is embedded into a space E^n = E_parallel + E_perp. Windows are attached to points of a lattice Lambda \\in E^n. For standard 5fold and icosahedral tiling models, the windows are perpendicular projections of dual Voronoi and Delone cells from Lambda. Their cuts by the position space E_parallel mark tiles and atomic positions. In the alternative covering approach, the position space is covered by overlapping copies of a quasi-unit cell which carries a fixed atomic configuration. The covering and window approach to quasicrystals are shown to be dual projects: D- and V- clusters are defined as projections to position space E_parallel of Delone or Voronoi cells. Decagonal V-clusters in the Penrose tiling, related to the decagon covering, and two types of pentagonal D-clusters in the triangle tiling of 5fold point symmetry with their windows are analyzed. They are linked, cover position space and have definite windows. For functions compatible with the tilings they form domains of definition. For icosahedral tilings the V-clusters are Kepler triacontahedra, the D-clusters are two icosahedra and one dodecahedron.

Peter Kramer

1999-04-01T23:59:59.000Z

475

Advanced binary geothermal power plants: Limits of performance  

SciTech Connect

The Heat Cycle Research Program is investigating potential improvements to power cycles utilizing moderate temperature geothermal resources to produce electrical power. Investigations have specifically examined Rankine cycle binary power systems. Binary Rankine cycles are more efficient than the flash steam cycles at moderate resource temperature, achieving a higher net brine effectiveness. At resource conditions similar to those at the Heber binary plant, it has been shown that mixtures of saturated hydrocarbons (alkanes) or halogenated hydrocarbons operating in a supercritical Rankine cycle gave improved performance over Rankine cycles with the pure working fluids executing single or dual boiling cycles or supercritical cycles. Recently, other types of cycles have been proposed for binary geothermal service. This report explores the feasible limits on efficiency of a plant given practical limits on equipment performance and discusses the methods used in these advanced concept plants to achieve the maximum possible efficiency. (Here feasible is intended to mean reasonably achievable and not cost-effective.) No direct economic analysis has been made because of the sensitivity of economic results to site specific input. The limit of performance of three advanced plants were considered in this report. The performance predictions were taken from the developers of each concept. The advanced plants considered appear to be approaching the feasible limit of performance. Ultimately, the plant designer must weigh the advantages and disadvantages of the the different cycles to find the best plant for a given service. In addition, this report presents a standard of comparison of the work which has been done in the Heat Cycle Research Program and in the industrial sector by Exergy, Inc. and Polythermal Technologies. 18 refs., 16 figs., 1 tab.

Bliem, C.J.; Mines, G.L.

1991-01-01T23:59:59.000Z

476

Advanced Integrated Traction System  

SciTech Connect

The United States Department of Energy elaborates the compelling need for a commercialized competitively priced electric traction drive system to proliferate the acceptance of HEVs, PHEVs, and FCVs in the market. The desired end result is a technically and commercially verified integrated ETS (Electric Traction System) product design that can be manufactured and distributed through a broad network of competitive suppliers to all auto manufacturers. The objectives of this FCVT program are to develop advanced technologies for an integrated ETS capable of 55kW peak power for 18 seconds and 30kW of continuous power. Additionally, to accommodate a variety of automotive platforms the ETS design should be scalable to 120kW peak power for 18 seconds and 65kW of continuous power. The ETS (exclusive of the DC/DC Converter) is to cost no more than $660 (55kW at $12/kW) to produce in quantities of 100,000 units per year, should have a total weight less than 46kg, and have a volume less than 16 liters. The cost target for the optional Bi-Directional DC/DC Converter is $375. The goal is to achieve these targets with the use of engine coolant at a nominal temperature of 105C. The system efficiency should exceed 90% at 20% of rated torque over 10% to 100% of maximum speed. The nominal operating system voltage is to be 325V, with consideration for higher voltages. This project investigated a wide range of technologies, including ETS topologies, components, and interconnects. Each technology and its validity for automotive use were verified and then these technologies were integrated into a high temperature ETS design that would support a wide variety of applications (fuel cell, hybrids, electrics, and plug-ins). This ETS met all the DOE 2010 objectives of cost, weight, volume and efficiency, and the specific power and power density 2015 objectives. Additionally a bi-directional converter was developed that provides charging and electric power take-off which is the first step towards enabling a smart-grid application. GM under this work assessed 29 technologies; investigated 36 configurations/types power electronics and electric machines, filed 41 invention disclosures; and ensured technology compatibility with vehicle production. Besides the development of a high temperature ETS the development of industrial suppliers took place because of this project. Suppliers of industrial power electronic components are numerous, but there are few that have traction drive knowledge. This makes it difficult to achieve component reliability, durability, and cost requirements necessary of high volume automotive production. The commercialization of electric traction systems for automotive industry requires a strong diverse supplier base. Developing this supplier base is dependent on a close working relationship between the OEM and supplier so that appropriate component requirements can be developed. GM has worked closely with suppliers to develop components for electric traction systems. Components that have been the focus of this project are power modules, capacitors, heavy copper boards, current sensors, and gate drive and controller chip sets. Working with suppliers, detailed component specifications have been developed. Current, voltage, and operation environment during the vehicle drive cycle were evaluated to develop higher resolution/accurate component specifications.

Greg Smith; Charles Gough

2011-08-31T23:59:59.000Z

477

ADVANCED CUTTINGS TRANSPORT STUDY  

Science Conference Proceedings (OSTI)

The Advanced Cuttings Transport Study (ACTS) was a 5-year JIP project undertaken at the University of Tulsa (TU). The project was sponsored by the U.S. Department of Energy (DOE) and JIP member companies. The objectives of the project were: (1) to develop and construct a new research facility that would allow three-phase (gas, liquid and cuttings) flow experiments under ambient and EPET (elevated pressure and temperature) conditions, and at different angle of inclinations and drill pipe rotation speeds; (2) to conduct experiments and develop a data base for the industry and academia; and (3) to develop mechanistic models for optimization of drilling hydraulics and cuttings transport. This project consisted of research studies, flow loop construction and instrumentation development. Following a one-year period for basic flow loop construction, a proposal was submitted by TU to the DOE for a five-year project that was organized in such a manner as to provide a logical progression of research experiments as well as additions to the basic flow loop. The flow loop additions and improvements included: (1) elevated temperature capability; (2) two-phase (gas and liquid, foam etc.) capability; (3) cuttings injection and removal system; (4) drill pipe rotation system; and (5) drilling section elevation system. In parallel with the flow loop construction, hydraulics and cuttings transport studies were preformed using drilling foams and aerated muds. In addition, hydraulics and rheology of synthetic drilling fluids were investigated. The studies were performed under ambient and EPET conditions. The effects of temperature and pressure on the hydraulics and cuttings transport were investigated. Mechanistic models were developed to predict frictional pressure loss and cuttings transport in horizontal and near-horizontal configurations. Model predictions were compared with the measured data. Predominantly, model predictions show satisfactory agreements with the measured data. As a part of this project, instrumentation was developed to monitor cuttings beds and characterize foams in the flow loop. An ultrasonic-based monitoring system was developed to measure cuttings bed thickness in the flow loop. Data acquisition software controls the system and processes the data. Two foam generating devices were designed and developed to produce foams with specified quality and texture. The devices are equipped with a bubble recognition system and an in-line viscometer to measure bubble size distribution and foam rheology, respectively. The 5-year project is completed. Future research activities will be under the umbrella of Tulsa University Drilling Research Projects. Currently the flow loop is being used for testing cuttings transport capacity of aqueous and polymer-based foams under elevated pressure and temperature conditions. Subsequently, the effect of viscous sweeps on cuttings transport under elevated pressure and temperature conditions will be investigated using the flow loop. Other projects will follow now that the ''steady state'' phase of the project has been achieved.

Stefan Miska; Troy Reed; Ergun Kuru

2004-09-30T23:59:59.000Z

478

Advanced Microturbine Systems  

SciTech Connect

In July 2000, the United Technologies Research Center (UTRC) was one of five recipients of a US Department of Energy contract under the Advanced Microturbine System (AMS) program managed by the Office of Distributed Energy (DE). The AMS program resulted from several government-industry workshops that recognized that microturbine systems could play an important role in improving customer choice and value for electrical power. That is, the group believed that electrical power could be delivered to customers more efficiently and reliably than the grid if an effective distributed energy strategy was followed. Further, the production of this distributed power would be accomplished with less undesirable pollutants of nitric oxides (NOx) unburned hydrocarbons (UHC), and carbon monoxide (CO). In 2000, the electrical grid delivered energy to US customers at a national average of approximately 32% efficiency. This value reflects a wide range of powerplants, but is dominated by older, coal burning stations that provide approximately 50% of US electrical power. The grid efficiency is also affected by transmission and distribution (T&D) line losses that can be significant during peak power usage. In some locations this loss is estimated to be 15%. Load pockets can also be so constrained that sufficient power cannot be transmitted without requiring the installation of new wires. New T&D can be very expensive and challenging as it is often required in populated regions that do not want above ground wires. While historically grid reliability has satisfied most customers, increasing electronic transactions and the computer-controlled processes of the 'digital economy' demand higher reliability. For them, power outages can be very costly because of transaction, work-in-progress, or perishable commodity losses. Powerplants that produce the grid electrical power emit significant levels of undesirable NOx, UHC, and CO pollutants. The level of emission is quoted as either a technology metric or a system-output metric. A common form for the technology metric is in the units of PPM {at} 15% O2. In this case the metric reflects the molar fraction of the pollutant in the powerplant exhaust when corrected to a standard exhaust condition as containing 15% (molar) oxygen, assuring that the PPM concentrations are not altered by subsequent air addition or dilution. Since fuel combustion consumes oxygen, the output oxygen reference is equivalent to a fuel input reference. Hence, this technology metric reflects the moles of pollutant per mole of fuel input, but not the useful output of the powerplant-i.e. the power. The system-output metric does embrace the useful output and is often termed an output-based metric. A common form for the output-based metric is in the units of lb/MWh. This is a system metric relating the pounds of pollutant to output energy (e.g., MWh) of the powerplant.

Rosfjord, T; Tredway, W; Chen, A; Mulugeta, J; Bhatia, T

2008-12-31T23:59:59.000Z

479

ADVANCED WORKER PROTECTION SYSTEM  

Science Conference Proceedings (OSTI)

From 1993 to 2000, OSS worked under a cost share contract from the Department of Energy (DOE) to develop an Advanced Worker Protection System (AWPS). The AWPS is a protective ensemble that provides the user with both breathing air and cooling for a NIOSH-rated duration of two hours. The ensemble consists of a liquid air based backpack, a Liquid Cooling Garment (LCG), and an outer protective garment. The AWPS project was divided into two phases. During Phase 1, OSS developed and tested a full-scale prototype AWPS. The testing showed that workers using the AWPS could work twice as long as workers using a standard SCBA. The testing also provided performance data on the AWPS in different environments that was used during Phase 2 to optimize the design. During Phase 1, OSS also performed a life-cycle cost analysis on a representative clean up effort. The analysis indicated that the AWPS could save the DOE millions of dollars on D and D activities and improve the health and safety of their workers. During Phase 2, OSS worked to optimize the AWPS design to increase system reliability, to improve system performance and comfort, and to reduce the backpack weight and manufacturing costs. To support this design effort, OSS developed and tested several different generations of prototype units. Two separate successful evaluations of the ensemble were performed by the International Union of Operation Engineers (IUOE). The results of these evaluations were used to drive the design. During Phase 2, OSS also pursued certifying the AWPS with the applicable government agencies. The initial intent during Phase 2 was to finalize the design and then to certify the system. OSS and Scott Health and Safety Products teamed to optimize the AWPS design and then certify the system with the National Institute of Occupational Health and Safety (NIOSH). Unfortunately, technical and programmatic difficulties prevented us from obtaining NIOSH certification. Despite the inability of NIOSH to certify the design, OSS was able to develop and successfully test, in both the lab and in the field, a prototype AWPS. They clearly demonstrated that a system which provides cooling can significantly increase worker productivity by extending the time they can function in a protective garment. They were also able to develop mature outer garment and LCG designs that provide considerable benefits over current protective equipment, such as self donning and doffing, better visibility, and machine washable. A thorough discussion of the activities performed during Phase 1 and Phase 2 is presented in the AWPS Final Report. The report also describes the current system design, outlines the steps needed to certify the AWPS, discusses the technical and programmatic issues that prevented the system from being certified, and presents conclusions and recommendations based upon the seven year effort.

Judson Hedgehock

2001-03-16T23:59:59.000Z

480

Advanced Distillation Final Report  

Science Conference Proceedings (OSTI)

The Advanced Distillation project was concluded on December 31, 2009. This U.S. Department of Energy (DOE) funded project was completed successfully and within budget during a timeline approved by DOE project managers, which included a one year extension to the initial ending date. The subject technology, Microchannel Process Technology (MPT) distillation, was expected to provide both capital and operating cost savings compared to conventional distillation technology. With efforts from Velocys and its project partners, MPT distillation was successfully demonstrated at a laboratory scale and its energy savings potential was calculated. While many objectives established at the beginning of the project were met, the project was only partially successful. At the conclusion, it appears that MPT distillation is not a good fit for the targeted separation of ethane and ethylene in large-scale ethylene production facilities, as greater advantages were seen for smaller scale distillations. Early in the project, work involved flowsheet analyses to discern the economic viability of ethane-ethylene MPT distillation and develop strategies for maximizing its impact on the economics of the process. This study confirmed that through modification to standard operating processes, MPT can enable net energy savings in excess of 20%. This advantage was used by ABB Lumus to determine the potential impact of MPT distillation on the ethane-ethylene market. The study indicated that a substantial market exists if the energy saving could be realized and if installed capital cost of MPT distillation was on par or less than conventional technology. Unfortunately, it was determined that the large number of MPT distillation units needed to perform ethane-ethylene separation for world-scale ethylene facilities, makes the targeted separation a poor fit for the technology in this application at the current state of manufacturing costs. Over the course of the project, distillation experiments were performed with the targeted mixture, ethane-ethylene, as well as with analogous low relative volatility systems: cyclohexane-hexane and cyclopentane-pentane. Devices and test stands were specifically designed for these efforts. Development progressed from experiments and models considering sections of a full scale device to the design, fabrication, and operation of a single-channel distillation unit with integrated heat transfer. Throughout the project, analytical and numerical models and Computational Fluid Dynamics (CFD) simulations were validated with experiments in the process of developing this platform technology. Experimental trials demonstrated steady and controllable distillation for a variety of process conditions. Values of Height-to-an-Equivalent Theoretical Plate (HETP) ranging from less than 0.5 inch to a few inches were experimentally proven, demonstrating a ten-fold performance enhancement relative to conventional distillation. This improvement, while substantial, is not sufficient for MPT distillation to displace very large scale distillation trains. Fortunately, parallel efforts in the area of business development have yielded other applications for MPT distillation, including smaller scale separations that benefit from the flowsheet flexibility offered by the technology. Talks with multiple potential partners are underway. Their outcome will also help determine the path ahead for MPT distillation.

Maddalena Fanelli; Ravi Arora; Annalee Tonkovich; Jennifer Marco; Ed Rode

2010-03-24T23:59:59.000Z

Note: This page contains sample records for the topic "advanced sequential dual" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


481

Simulations of Dual-Vortex Interaction within Environmental Shear  

Science Conference Proceedings (OSTI)

For over a century it has been known that each vortex in a multiple vortex configuration will move in response to the other vortices. However, despite advances since that time, the complexities of multiple vortex scenarios when sheared ...

Robert E. Hart; Jenni L. Evans

1999-11-01T23:59:59.000Z

482

Dual Phase Membrane for High Temperature CO2 Separation  

SciTech Connect

This project aimed at synthesis of a new inorganic dual-phase carbonate membrane for high temperature CO{sub 2} separation. Metal-carbonate dual-phase membranes were prepared by the direct infiltration method and the synthesis conditions were optimized. Permeation tests for CO{sub 2} and N{sub 2} from 450-750 C showed very low permeances of those two gases through the dual-phase membrane, which was expected due to the lack of ionization of those two particular gases. Permeance of the CO{sub 2} and O{sub 2} mixture was much higher, indicating that the gases do form an ionic species, CO{sub 3}{sup 2-}, enhancing transport through the membrane. However, at temperatures in excess of 650 C, the permeance of CO{sub 3}{sup 2-} decreased rapidly, while predictions showed that permeance should have continued to increase with temperature. XRD data obtained from used membrane indicated that lithium iron oxides formed on the support surface. This lithium iron oxide layer has a very low conductivity, which drastically reduces the flow of electrons to the CO{sub 2}/O{sub 2} gas mixtu