Powered by Deep Web Technologies
Note: This page contains sample records for the topic "adopted interconnection standards" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


1

Interconnection Standards  

Broader source: Energy.gov [DOE]

New York first adopted uniform interconnection standards in 1999 (see history below). The Standard Interconnection Requirements (SIR) have subsequently been amended several times since, most...

2

Interconnection Standards  

Broader source: Energy.gov [DOE]

The Michigan Public Service Commission (PSC) first adopted interconnection standards for distributed generation (DG) in September 2003. The original standards provided for 5 levels of...

3

Interconnection Standards  

Broader source: Energy.gov [DOE]

The Pennsylvania Public Utilities Commission was required to adopt interconnection standards and net-metering rules by the Alternative Energy Portfolio Standards Act of 2004.The PUC subsequently...

4

Interconnection Standards  

Broader source: Energy.gov [DOE]

The North Carolina Utilities Commission (NCUC) adopted comprehensive interconnection standards for distributed generation in June 2008. The NCUC standards, which are similar to the Federal Energy...

5

Interconnection Standards  

Broader source: Energy.gov [DOE]

In February 2004, the Wisconsin Public Service Commission adopted interconnection standards for distributed generation (DG) systems up to 15 megawatts (MW) in capacity. All investor-owned...

6

Interconnection Standards  

Broader source: Energy.gov [DOE]

In September 2007, the Washington Utilities and Transportation Commission (UTC) adopted interconnection standards for distributed generation (DG) systems up to 20 megawatts (MW) in capacity. The...

7

Interconnection Standards  

Broader source: Energy.gov [DOE]

In December 2005, the Colorado Public Utilities Commission (PUC) adopted standards for net metering and interconnection, as required by Amendment 37, a renewable-energy ballot initiative approved...

8

Interconnection Standards  

Broader source: Energy.gov [DOE]

South Dakotaís interconnection standards for distributed generation, adopted by the state Public Utilities Commission (PUC) in May 2009, apply to customers of investor-owned utilities.* The rules...

9

Interconnection Standards  

Broader source: Energy.gov [DOE]

Vermont has adopted separate interconnection standards for net-metered energy systems that are 150 kW or less, and for all other distributed-generation (DG) systems.

10

Interconnection Standards  

Broader source: Energy.gov [DOE]

In December 2003, the Nevada Public Utilities Commission (PUC) adopted interconnection standards for customers of NV Energy (formerly Nevada Power and Sierra Pacific Power) with on-site generation...

11

Interconnection Standards  

Broader source: Energy.gov [DOE]

In July 2010, the Montana Public Service Commission (PSC) adopted interconnection rules, effective August 13, 2010. These rules apply to all electric utilities under the PSC's jurisdiction,...

12

Interconnection Standards  

Broader source: Energy.gov [DOE]

The Maine Public Utility Commission (PUC) adopted interconnection procedures in January 2010. These rules apply to all transmission and distribution utilities operating in the state and apply to...

13

Interconnection Standards  

Broader source: Energy.gov [DOE]

Virginia has two interconnection standards: one for net-metered systems and one for systems that are not net-metered.

14

Interconnection Standards  

Broader source: Energy.gov [DOE]

New Jersey's interconnection standards apply statewide to all electric distribution utilities, but not to the small number of municipal utilities and electric cooperatives in the state. The rules,...

15

Interconnection Standards  

Broader source: Energy.gov [DOE]

Note: Legislation enacted in August 2012 required the Massachusetts Department of Public Utilities (DPU) to develop an enforceable, standard interconnection timeline for distributed generation...

16

Interconnection Standards  

Broader source: Energy.gov [DOE]

In March 2008, the Florida Public Service Commission (PSC) adopted interconnection rules for renewable-energy systems up to two megawatts (MW) in capacity. The PSC rules apply only to the state's...

17

Interconnection Standards  

Broader source: Energy.gov [DOE]

Interconnection in New Mexico is governed by New Mexico Public Regulation Commission (PRC) Rule 568 and Rule 569. These rules, adopted in July 2008, revised and clarified the state's existing rules...

18

Interconnection Standards  

Broader source: Energy.gov [DOE]

Oregon has three separate interconnection standards: one for net-metered systems, one for small generator facilities (non-net metered systems) and one for large generator facilities (non-net...

19

Puerto Rico- Interconnection Standards  

Broader source: Energy.gov [DOE]

In 2007, the Autoridad de EnergŪa Electrica de Puerto Rico (PREPA*) adopted interconnection standards based on the standard contained in the federal Energy Policy Act of 2005. PREPA promulgated...

20

Interconnection Standards  

Broader source: Energy.gov [DOE]

In November 2005, the Indiana Utility Regulatory Commission (IURC) approved rules governing the interconnection of distributed generation (DG). Indiana's interconnection rules require the state's...

Note: This page contains sample records for the topic "adopted interconnection standards" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


21

Interconnection Standards  

Broader source: Energy.gov [DOE]

Different rules govern the interconnection of distributed generation facilities in Iowa, depending on whether or not the interconnection is with a utility whose rates are regulated by the Iowa...

22

Interconnection Standards for Small Generators  

Broader source: Energy.gov [DOE]

The Federal Energy Regulatory Commission (FERC) adopted "small generator" interconnection standards for distributed energy resources up to 20 megawatts (MW) in capacity in May 2005.* The FERC's...

23

Interconnection Standards  

Broader source: Energy.gov [DOE]

In December 2007, the Connecticut Department of Public Utility Control (DPUC) now called the Public Utilities Regulatory Authority (PURA) approved new interconnection guidelines for distributed...

24

Interconnection Standards  

Broader source: Energy.gov [DOE]

In April 2008, Kentucky enacted legislation which required the Kentucky Public Service Commission (PSC) to develop interconnection and net metering guidelines for all retail electric suppliers...

25

Interconnection Standards  

Broader source: Energy.gov [DOE]

In July 2006 the District of Columbia Public Service Commission (PSC) initiated a formal inquiry into the development of uniform interconnection procedures for on-site distributed generation...

26

Interconnection Standards  

Broader source: Energy.gov [DOE]

In 2006, West Virginia stakeholders came together to consider net metering, interconnection as required by the Federal Energy Policy Act (2005) and agreed upon a "Statement of Consensus Among...

27

Interconnection Standards  

Broader source: Energy.gov [DOE]

Hawaii has established simplified interconnection rules for small renewables and separate rules for all other distributed generation (DG). For inverter-based systems up to 10 kilowatts (kW) in...

28

innovati nInterconnection Standards Guide Integration of Distributed  

E-Print Network [OSTI]

Engineers (IEEE). The goal: to create consensus standards with participation from industry, utilities, government, and others to guide the integration of renewable and other small electricity generation, or used IEEE 1547 in the development of their own interconnection standards, and the Energy Policy Act

29

Why Do States Adopt Renewable Portfolio Standards?: An Empirical Investigation  

E-Print Network [OSTI]

131 Why Do States Adopt Renewable Portfolio Standards?: An Empirical Investigation Thomas P. Lyon* and Haitao Yin** Renewable portfolio standards (RPSs) for electricity generation are politically popularU.S.stategovernments of Renewable Portfolio Standards (RPSs) as a policy tool for promoting renewable electricity generation. An RPS

Lyon, Thomas P.

30

Energy standards and model codes development, adoption, implementation, and enforcement  

SciTech Connect (OSTI)

This report provides an overview of the energy standards and model codes process for the voluntary sector within the United States. The report was prepared by Pacific Northwest Laboratory (PNL) for the Building Energy Standards Program and is intended to be used as a primer or reference on this process. Building standards and model codes that address energy have been developed by organizations in the voluntary sector since the early 1970s. These standards and model codes provide minimum energy-efficient design and construction requirements for new buildings and, in some instances, existing buildings. The first step in the process is developing new or revising existing standards or codes. There are two overall differences between standards and codes. Energy standards are developed by a consensus process and are revised as needed. Model codes are revised on a regular annual cycle through a public hearing process. In addition to these overall differences, the specific steps in developing/revising energy standards differ from model codes. These energy standards or model codes are then available for adoption by states and local governments. Typically, energy standards are adopted by or adopted into model codes. Model codes are in turn adopted by states through either legislation or regulation. Enforcement is essential to the implementation of energy standards and model codes. Low-rise residential construction is generally evaluated for compliance at the local level, whereas state agencies tend to be more involved with other types of buildings. Low-rise residential buildings also may be more easily evaluated for compliance because the governing requirements tend to be less complex than for commercial buildings.

Conover, D.R.

1994-08-01T23:59:59.000Z

31

U.S. Virgin Islands Establishes Interconnection Standards to...  

Office of Environmental Management (EM)

ensure that the procedure it ultimately adopted would encourage and promote renewable energy development without compromising the safety and reliability of the electricity...

32

Interconnection Guidelines  

Broader source: Energy.gov [DOE]

The South Carolina Public Service Commission (PSC) adopted simplified interconnection guidelines for small distributed generation (DG) in December 2006. These guidelines address renewable-energy...

33

IEEE Smart Grid Series of Standards IEEE 2030 (Interoperability) and IEEE 1547 (Interconnection) Status: Preprint  

SciTech Connect (OSTI)

The IEEE American National Standards smart grid publications and standards development projects IEEE 2030, which addresses smart grid interoperability, and IEEE 1547TM, which addresses distributed resources interconnection with the grid, have made substantial progress since 2009. The IEEE 2030TM and 1547 standards series focus on systems-level aspects and cover many of the technical integration issues involved in a mature smart grid. The status and highlights of these two IEEE series of standards, which are sponsored by IEEE Standards Coordinating Committee 21 (SCC21), are provided in this paper.

Basso, T.; DeBlasio, R.

2012-04-01T23:59:59.000Z

34

Interconnection Guidelines  

Broader source: Energy.gov [DOE]

'''''Note: In June 2007, the Arizona Corporation Commission (ACC) initiated a rulemaking process to establish statewide interconnection standards for distributed generation (DG). This proceeding...

35

Interconnection Standards  

Broader source: Energy.gov [DOE]

'''''Note: In July 2012, the Public Utilities Commission of Ohio (PUCO) opened a docket ([http://dis.puc.state.oh.us/CaseRecord.aspx?CaseNo=12-2051&x=0&y=0 Case 12-0251-EL-ORD]) to review...

36

Interconnection Standards  

Broader source: Energy.gov [DOE]

New Hampshire requires all utilities selling electricity in the state to offer net metering to customers who own or operate systems up to one megawatt (1 MW) in capacity that generate electricity...

37

Interconnection Standards  

Broader source: Energy.gov [DOE]

Minnesota's net-metering law, enacted in 1983, applies to all investor-owned utilities, municipal utilities and rural electric cooperatives. Qualifying facilities of less than 1,000 kilowatts (kW)...

38

Interconnection Standards  

Broader source: Energy.gov [DOE]

In August 2007, Illinois enacted legislation [http://www.ilga.gov/legislation/publicacts/fulltext.asp?Name=095-0420&GA... (S.B. 680)] requiring the Illinois Commerce Commission (ICC) to...

39

Interconnection Standards  

Broader source: Energy.gov [DOE]

In April 2007, Maryland enacted legislation ([http://mgaleg.maryland.gov/2007RS/chapters_noln/Ch_119_sb0595E.pdf S.B. 595]) requiring the Maryland Public Service Commission (PSC) to form a small...

40

Interconnection Standards  

Broader source: Energy.gov [DOE]

Utah requires the state's only investor-owned utility, Rocky Mountain Power (RMP), and most electric cooperatives* to offer net metering to customers who generate electricity using solar energy,...

Note: This page contains sample records for the topic "adopted interconnection standards" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


41

Interconnection Standards  

Broader source: Energy.gov [DOE]

The Texas Public Utility Regulatory Act (PURA) of 1999 included a provision that "a customer is entitled to have access to on-site distributed generation". As a result, the Public Utility...

42

Interconnection Standards  

Broader source: Energy.gov [DOE]

'''''Note: The California Public Utilities Commission (CPUC) approved a [http://docs.cpuc.ca.gov/EFILE/MOTION/162852.PDF proposed settlement] in September 2012, enacting the first fundamental...

43

Interconnection Guidelines  

Broader source: Energy.gov [DOE]

Kansas adopted the Net Metering and Easy Connection Act in May 2009 (see K.S.A. 66-1263 through 66-1271), establishing interconnection guidelines and net metering for customer-owned generators. Net...

44

Determinants of effective information transfer in international regulatory standards adoption.  

E-Print Network [OSTI]

?? The role of international regulatory standards within the current global environment has become of the most importance. The age of the global system andÖ (more)

Popescu, Denisa

2010-01-01T23:59:59.000Z

45

Application for Locally Adopted Energy Standards by the City of Pacifica in Accordance With  

E-Print Network [OSTI]

Application for Locally Adopted Energy Standards by the City of Pacifica in Accordance With Section;Application for Pacifica Locally Adopted Energy Standards, 12/29/10 Page 1 Executive Summary The Pacifica City concerning public health and safety in the San Francisco Bay Area. A reduction of total and peak energy use

46

Application for Locally Adopted Energy Standards by the City of Union City in Accordance With  

E-Print Network [OSTI]

Standards in order to meet the minimum energy efficiency requirements of the proposed ordinance. Overall), that exceed any applicable federal energy conservation standards for such products." #12;Application for UnionApplication for Locally Adopted Energy Standards by the City of Union City in Accordance

47

Application for Locally Adopted Energy Standards by the City of Cupertino  

E-Print Network [OSTI]

energy conservation measures; and/or, set more stringent energy budgets. Because these energy standards Standards 3 The required level energy performance that exceeds the Title 24, Part 6 minimum is the resultApplication for Locally Adopted Energy Standards by the City of Cupertino In Accordance

48

Accelerating the Adoption of Second-Tier Reach Standards forApplicable Appliance Products in China  

SciTech Connect (OSTI)

The minimum energy efficiency standards program for household appliances in China was initiated in 1989. Since 1996, CLASP and its implementing partner, LBNL, have assisted China in developing 11 minimum energy performance standards (MEPS) for 9 products and endorsement labels for 11 products including: refrigerators; air conditioners; clothes washers; televisions; printers; computers; monitors; fax machines; copiers; DVD/VCD players; external power supplies; and set-top boxes (under development). Before 2003, China's traditional approach to standards development involved small increases in efficiency requirements for implementation within 6 months of a standard's approval. Since 2003, China has adopted a new approach in setting MEPS. This new approach involves the development of two tiers of standards--one for initial implementation and a second tier at a more aggressive level of energy efficiency for implementation three to five years later. The second-tier standard is also referred to as a 'reach standard'. Reach standards have now been developed in China for: color TVs; refrigerators; air conditioners; and external power supplies. This report is presented in five sections. After the introduction in Section 1, Section 2 analyzes the distribution of the efficiency of refrigerators and air-conditioners in China based on data collected by the China Energy Label Center for the mandatory energy information label program. The results provide an assessment of the adoption of reach standards for these two products. Section 3 summarizes on-going collaborations with Shanghai related to early local adoption of reach standards, and presents both the impact and an analysis of barriers to the local adoption of reach standard for air-conditioners. Section 4 offers suggestions for local governments on how to move forward in adopting reach standards in their localities and concludes with a summary of the results and a plan for developing local capacity in order to achieve success in adopting reach standards.

Lin, Jiang; Fridley, David

2007-03-01T23:59:59.000Z

49

Status of state and local adoption of energy standards for new commercial buildings  

SciTech Connect (OSTI)

This paper presents a summary of building energy standards adoption by state and major local governments and how the standards apply to new commercial buildings. Numerous public and private sector agencies and organizations develop energy standards and codes for commercial buildings. These documents serve, among others, state and local legislators and regulators who are interested in requiring their use to reduce the energy consumption of new commercial buildings. Through adoption or adaptation of these documents by state or local governments, minimum acceptable design and construction criteria for new commercial buildings are established in law. The energy standard or code adopted, or used as a basis for a state developed standard, may be any one of a number of documents. The authority of the state to regulate construction may apply throughout the entire state, only to a few types of buildings, or may be absent, in which case local government has regulatory authority. The means of adoption may be by legislation, regulation, municipal code, or other legal vehicle. At the present time there are widespread differences in the energy standards adopted by state and local government and the application of these standards to new commercial buildings.

Boulin, J.J. [USDOE, Washington, DC (United States); Conover, D.R. [Pacific Northwest Lab., Richland, WA (United States)

1992-09-01T23:59:59.000Z

50

Analysis of Potential Benefits and Costs of Adopting a Commercial Building Energy Standard in South Dakota  

SciTech Connect (OSTI)

The state of South Dakota is considering adopting a commercial building energy standard. This report evaluates the potential costs and benefits to South Dakota residents from requiring compliance with the most recent edition of the ANSI/ASHRAE/IESNA 90.1-2001 Energy Standard for Buildings except Low-Rise Residential Buildings. These standards were developed in an effort to set minimum requirements for the energy efficient design and construction of new commercial buildings. The quantitative benefits and costs of adopting a commercial building energy code are modeled by comparing the characteristics of assumed current building practices with the most recent edition of the ASHRAE Standard, 90.1-2001. Both qualitative and quantitative benefits and costs are assessed in this analysis. Energy and economic impacts are estimated using results from a detailed building simulation tool (Building Loads Analysis and System Thermodynamics [BLAST] model) combined with a Life-Cycle Cost (LCC) approach to assess corresponding economic costs and benefits.

Belzer, David B.; Cort, Katherine A.; Winiarski, David W.; Richman, Eric E.

2005-03-04T23:59:59.000Z

51

Interconnection Panel  

Broader source: Energy.gov [DOE]

Presentationógiven at at the Fall 2012 Federal Utility Partnership Working Group (FUPWG) meetingódiscusses the interconnection panel, including an overview of the generation interconnection process (GIP), and interconnection agreements and their terms.

52

Energy and Economic Impacts of U.S. Federal Energy and Water Conservation Standards Adopted From 1987 Through 2010  

SciTech Connect (OSTI)

This paper presents estimates of the key impacts of the energy and water conservation standards that have been adopted from 1987 through 2010. The standards covered include those set by legislation as well as standards adopted by DOE through rulemaking. We estimate that energy efficiency standards for consumer products and certain commercial and industrial equipment that have been adopted from 1987 through 2010 saved 3.0 quads in 2010, have had a cumulative energy savings of 25.9 quads through 2010 and will achieve cumulative energy savings of 158 quads over the period 1990-2070. Thus, the majority of the savings are still to come as products subject to standards enter the stock. Furthermore, the standards will have a cumulative net present value (NPV) of consumer benefit of between $851 billion and $1,103 billion, using 7 percent and 3 percent discount rates, respectively. In addition, we estimate the water conservation standards, together with those energy conservation standards that also save water, saved residential consumers 1.5 trillion gallons of water in 2010, have had cumulative water savings of 11.7 trillion gallons through 2010, and will achieve cumulative water savings by 2040 of 51.4 trillion gallons.

Meyers, Stephen; Williams, Alison; Chan, Peter

2011-12-07T23:59:59.000Z

53

Interconnection Guidelines (Rhode Island)  

Broader source: Energy.gov [DOE]

Rhode Island enacted legislation (HB 6222) in June 2011 to standardize the application process for the interconnection of customer-sited renewable-energy systems to the stateís distribution grid....

54

In 1991 UC Irvine adopted standards to outperform California's Title 24 Energy Efficiency Standards by 30 percent, use 100 percent reclaimed water, CO2 sensing for  

E-Print Network [OSTI]

in Sacramento. · Nine buildings at UC Irvine bear the U.S. Green Building Council's Leadership in Energy· In 1991 UC Irvine adopted standards to outperform California's Title 24 Energy Efficiency, and no rainforest hardwoods · UC Irvine's Smart Labs Initiative, which reduces energy consumption in new

Rose, Michael R.

55

Interconnection Standards (Utah  

Open Energy Info (EERE)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data CenterFranconia, Virginia: Energy Resources Jump to:46 - 429 Throttled (bot load) ErrorEnergyInnovationInterContinental Hotels

56

Energy and Economic Impacts of U.S. Federal Energy and Water Conservation Standards Adopted From 1987 Through 2013  

SciTech Connect (OSTI)

This paper presents estimates of the key impacts of Federal energy and water conservation standards adopted from 1987 through 2013. The standards for consumer products and commercial and industrial equipment include those set by legislation as well as standards adopted by DOE through rulemaking. In 2013, the standards saved an estimated 4.05 quads of primary energy, which is equivalent to 4% of total U.S. energy consumption. The savings in operating costs for households and businesses totaled $56 billion. The average household saved $361 in operating costs as a result of residential and plumbing product standards. The estimated reduction in CO{sub 2} emissions associated with the standards in 2013 was 218 million metric tons, which is equivalent to 4% of total U.S. CO{sub 2} emissions. The estimated cumulative energy savings over the period 1990-2090 amount to 181 quads. Accounting for the increased upfront costs of more-efficient products and the operating cost (energy and water) savings over the productsí lifetime, the standards have a past and projected cumulative net present value (NPV) of consumer benefit of between $1,271 billion and $1,487 billion, using 7 percent and 3 percent discount rates, respectively. The water conservation standards, together with energy conservation standards that also save water, reduced water use by 1.9 trillion gallons in 2013, and will achieve cumulative water savings by 2090 of 55 trillion gallons. The estimated consumer savings in 2013 from reduced water use amounted to $16 billon.

Meyers, Stephen; Williams, Alison; Chan, Peter

2014-06-30T23:59:59.000Z

57

IN SEARCH OF ISO: AN INSTITUTIONAL PERSPECTIVE ON THE ADOPTION OF INTERNATIONAL MANAGEMENT STANDARDS  

E-Print Network [OSTI]

E.C. Gutzwiller. 1999 ďBuying into ISO 14001Ē. Occupationalnational production regimes: ISO 9000 standards in the2001 ďInternational diffusion of ISO 14001 certification. Ē

Delmas, Magali A.

2003-01-01T23:59:59.000Z

58

Interconnection Resources  

Broader source: Energy.gov [DOE]

Interconnection is the technical procedures and legal requirements surrounding energy customers' ability to connect their small-scale renewable energy projects with the electricity grid. The...

59

Interconnection Guidelines  

Broader source: Energy.gov [DOE]

Nebraska enacted legislation in May 2009 [http://nebraskalegislature.gov/FloorDocs/101/PDF/Final/LB436.pdf (LB 436)], establishing general rules for interconnecting and net metering systems that...

60

Interconnection Guidelines  

Broader source: Energy.gov [DOE]

Wyoming's net-metering law includes basic interconnection requirements for systems up to 25 kilowatts (kW) in capacity that generate electricity using solar, wind, hydropower or biomass resources....

Note: This page contains sample records for the topic "adopted interconnection standards" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


61

CHP: Connecting the Gap between Markets and Utility Interconnection...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Markets and Utility Interconnection and Tariff Practices, 2006 The adoption of combined heat and power (CHP) systems by American industries has made substantial strides in the...

62

Analysis of Potential Benefits and Costs of Adopting ASHRAE Standard 90.1-2001 as the Commercial Building Energy Code in Tennessee  

SciTech Connect (OSTI)

ASHRAE Standard 90.1-2001 Energy Standard for Buildings except Low-Rise Residential Buildings (hereafter referred to as ASHRAE 90.1-2001 or 90.1-2001) was developed in an effort to set minimum requirements for the energy efficient design and construction of new commercial buildings. The State of Tennessee is considering adopting ASHRAE 90.1-2001 as its commercial building energy code. In an effort to evaluate whether or not this is an appropriate code for the state, the potential benefits and costs of adopting this standard are considered in this report. Both qualitative and quantitative benefits and costs are assessed. Energy and economic impacts are estimated using the Building Loads Analysis and System Thermodynamics (BLAST) simulations combined with a Life-Cycle Cost (LCC) approach to assess corresponding economic costs and benefits. Tennessee currently has ASHRAE Standard 90A-1980 as the statewide voluntary/recommended commercial energy standard; however, it is up to the local jurisdiction to adopt this code. Because 90A-1980 is the recommended standard, many of the requirements of ASHRAE 90A-1980 were used as a baseline for simulations.

Cort, Katherine A.; Winiarski, David W.; Belzer, David B.; Richman, Eric E.

2004-09-30T23:59:59.000Z

63

Advanced Interconnect Development  

SciTech Connect (OSTI)

The objectives of this project are to develop cost-effective, optimized materials for intermediate temperature SOFC interconnect and interconnect/electrode interface applications and identify and understand degradation processes in interconnects and at their interfaces with electrodes.

Yang, Z.G.; Maupin, G.; Simner, S.; Singh, P.; Stevenson, J.; Xia, G.

2005-01-27T23:59:59.000Z

64

Interconnection Standards | Open Energy Information  

Open Energy Info (EERE)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home5b9fcbce19 No revision hasInformation Earth's Heat JumpInc Place: EdenOverview Of The Data, Regional Patterns |

65

Interconnection networks  

DOE Patents [OSTI]

A network of interconnected processors is formed from a vertex symmetric graph selected from graphs GAMMA/sub d/(k) with degree d, diameter k, and (d + 1)exclamation/ (d /minus/ k + 1)exclamation processors for each d greater than or equal to k and GAMMA/sub d/(k, /minus/1) with degree d /minus/ 1, diameter k + 1, and (d + 1)exclamation/(d /minus/ k + 1)exclamation processors for each d greater than or equal to k greater than or equal to 4. Each processor has an address formed by one of the permutations from a predetermined sequence of letters chosen a selected number of letters at a time, and an extended address formed by appending to the address the remaining ones of the predetermined sequence of letters. A plurality of transmission channels is provided from each of the processors, where each processor has one less channel than the selected number of letters forming the sequence. Where a network GAMMA/sub d/(k, /minus/1) is provided, no processor has a channel connected to form an edge in a direction delta/sub 1/. Each of the channels has an identification number selected from the sequence of letters and connected from a first processor having a first extended address to a second processor having a second address formed from a second extended address defined by moving to the front of the first extended address the letter found in the position within the first extended address defined by the channel identification number. The second address is then formed by selecting the first elements of the second extended address corresponding to the selected number used to form the address permutations. 9 figs.

Faber, V.; Moore, J.W.

1988-06-20T23:59:59.000Z

66

Adoption of Voluntary Environmental Standards: The Role of Signaling and Intrinsic Benefits in the Diffusion of the LEED Green Building Standards.  

E-Print Network [OSTI]

the Diffusion of Green Building Practices. Ē AppliedCosts and Financial Benefits of Green Buildings: A Report toDiffusion of the LEED Green Building Standards August 17,

Corbett, C.J.; Muthulingam, S.

2007-01-01T23:59:59.000Z

67

Potential Impact of Adopting Maximum Technologies as Minimum Efficiency Performance Standards in the U.S. Residential Sector  

SciTech Connect (OSTI)

The US Department of Energy (US DOE) has placed lighting and appliance standards at a very high priority of the U.S. energy policy. However, the maximum energy savings and CO2 emissions reduction achievable via minimum efficiency performance standards (MEPS) has not yet been fully characterized. The Bottom Up Energy Analysis System (BUENAS), first developed in 2007, is a global, generic, and modular tool designed to provide policy makers with estimates of potential impacts resulting from MEPS for a variety of products, at the international and/or regional level. Using the BUENAS framework, we estimated potential national energy savings and CO2 emissions mitigation in the US residential sector that would result from the most aggressive policy foreseeable: standards effective in 2014 set at the current maximum technology (Max Tech) available on the market. This represents the most likely characterization of what can be maximally achieved through MEPS in the US. The authors rely on the latest Technical Support Documents and Analytical Tools published by the U.S. Department of Energy as a source to determine appliance stock turnover and projected efficiency scenarios of what would occur in the absence of policy. In our analysis, national impacts are determined for the following end uses: lighting, television, refrigerator-freezers, central air conditioning, room air conditioning, residential furnaces, and water heating. The analyzed end uses cover approximately 65percent of site energy consumption in the residential sector (50percent of the electricity consumption and 80percent of the natural gas and LPG consumption). This paper uses this BUENAS methodology to calculate that energy savings from Max Tech for the U.S. residential sector products covered in this paper will reach an 18percent reduction in electricity demand compared to the base case and 11percent in Natural Gas and LPG consumption by 2030 The methodology results in reductions in CO2 emissions of a similar magnitude.

Letschert, Virginie; Desroches, Louis-Benoit; McNeil, Michael; Saheb, Yamina

2010-05-03T23:59:59.000Z

68

Generation Interconnection Policies and Wind Power: A Discussion of Issues, Problems, and Potential Solutions  

SciTech Connect (OSTI)

This report describes the adoption and implementation of FERC Order 2003 and the reasons for the sharp rise in generation interconnection filings in recent years.

Porter, K.; Fink, S.; Mudd, C.; DeCesaro, J.

2009-01-01T23:59:59.000Z

69

Updating Technical Screens for PV Interconnection: Preprint  

SciTech Connect (OSTI)

Solar photovoltaics (PV) is the dominant type of distributed generation (DG) technology interconnected to electric distribution systems in the United States, and deployment of PV systems continues to increase rapidly. Considering the rapid growth and widespread deployment of PV systems in United States electric distribution grids, it is important that interconnection procedures be as streamlined as possible to avoid unnecessary interconnection studies, costs, and delays. Because many PV interconnection applications involve high penetration scenarios, the process needs to allow for a sufficiently rigorous technical evaluation to identify and address possible system impacts. Existing interconnection procedures are designed to balance the need for efficiency and technical rigor for all DG. However, there is an implicit expectation that those procedures will be updated over time in order to remain relevant with respect to evolving standards, technology, and practical experience. Modifications to interconnection screens and procedures must focus on maintaining or improving safety and reliability, as well as accurately allocating costs and improving expediency of the interconnection process. This paper evaluates the origins and usefulness of the capacity penetration screen, offers potential short-term solutions which could effectively allow fast-track interconnection to many PV system applications, and considers longer-term solutions for increasing PV deployment levels in a safe and reliable manner while reducing or eliminating the emphasis on the penetration screen.

Coddington, M.; Ellis, A.; Lynn, K.; Razon, A.; Key, T.; Kroposki, B.; Mather, B.; Hill, R.; Nicole, K.; Smith, J.

2012-08-01T23:59:59.000Z

70

PJM Interconnection (Multiple States)  

Broader source: Energy.gov [DOE]

PJM (originally Pennsylvania, Jersey, Maryland) Interconnection is a Regional Transmission Organization (RTO) that coordinates the movement of wholesale electricity in all or parts of Delaware,...

71

Interconnect Issues in NE  

Broader source: Energy.gov [DOE]

Presentation covers interconnect issues in the Northeast and is given at the Spring 2010 Federal Utility Partnership Working Group (FUPWG) meeting in Providence, Rhode Island.

72

Perforation patterned electrical interconnects  

DOE Patents [OSTI]

This disclosure describes systems and methods for increasing the usable surface area of electrical contacts within a device, such as a thin film solid state device, through the implementation of electrically conductive interconnects. Embodiments described herein include the use of a plurality of electrically conductive interconnects that penetrate through a top contact layer, through one or more multiple layers, and into a bottom contact layer. The plurality of conductive interconnects may form horizontal and vertical cross-sectional patterns. The use of lasers to form the plurality of electrically conductive interconnects from reflowed layer material further aids in the manufacturing process of a device.

Frey, Jonathan

2014-01-28T23:59:59.000Z

73

Solar cell array interconnects  

DOE Patents [OSTI]

Electrical interconnects are disclosed for solar cells or other electronic components using a silver-silicone paste or a lead-tin (Pb-Sn) no-clean fluxless solder cream, whereby the high breakage of thin (<6 mil thick) solar cells using conventional solder interconnect is eliminated. The interconnects of this invention employs copper strips which are secured to the solar cells by a silver-silicone conductive paste which can be used at room temperature, or by a Pb-Sn solder cream which eliminates undesired residue on the active surfaces of the solar cells. Electrical testing using the interconnects of this invention has shown that no degradation of the interconnects developed under high current testing, while providing a very low contact resistance value. 4 figs.

Carey, P.G.; Thompson, J.B.; Colella, N.J.; Williams, K.A.

1995-11-14T23:59:59.000Z

74

Solar cell array interconnects  

DOE Patents [OSTI]

Electrical interconnects for solar cells or other electronic components using a silver-silicone paste or a lead-tin (Pb-Sn) no-clean fluxless solder cream, whereby the high breakage of thin (<6 mil thick) solar cells using conventional solder interconnect is eliminated. The interconnects of this invention employs copper strips which are secured to the solar cells by a silver-silicone conductive paste which can be used at room temperature, or by a Pb-Sn solder cream which eliminates undesired residue on the active surfaces of the solar cells. Electrical testing using the interconnects of this invention has shown that no degradation of the interconnects developed under high current testing, while providing a very low contact resistance value.

Carey, Paul G. (Mountain View, CA); Thompson, Jesse B. (Brentwood, CA); Colella, Nicolas J. (Livermore, CA); Williams, Kenneth A. (Livermore, CA)

1995-01-01T23:59:59.000Z

75

Micro-fluidic interconnect  

DOE Patents [OSTI]

An apparatus for simultaneously aligning and interconnecting microfluidic ports is presented. Such interconnections are required to utilize microfluidic devices fabricated in Micro-Electromechanical-Systems (MEMS) technologies, that have multiple fluidic access ports (e.g. 100 micron diameter) within a small footprint, (e.g. 3 mm.times.6 mm). Fanout of the small ports of a microfluidic device to a larger diameter (e.g. 500 microns) facilitates packaging and interconnection of the microfluidic device to printed wiring boards, electronics packages, fluidic manifolds etc.

Okandan, Murat (Albuquerque, NM); Galambos, Paul C. (Albuquerque, NM); Benavides, Gilbert L. (Los Ranchos, NM); Hetherington, Dale L. (Albuquerque, NM)

2006-02-28T23:59:59.000Z

76

Passive microfluidic interconnects  

E-Print Network [OSTI]

Equipment and procedures were developed to test two passive microfluidic interconnect rings held together by the friction forces on the contact surfaces. The second design forms fluid seals by means of thin flared rings ...

Jonnalagadda, Aparna S

2005-01-01T23:59:59.000Z

77

Reliability of Electrical Interconnects (Presentation)  

SciTech Connect (OSTI)

This presentation discusses the status of NREL's research on the reliability of electrical interconnects.

Devoto, D.

2014-06-01T23:59:59.000Z

78

Updating Small Generator Interconnection Procedures for New Market Conditions  

SciTech Connect (OSTI)

Federal and state regulators are faced with the challenge of keeping interconnection procedures updated against a backdrop of evolving technology, new codes and standards, and considerably transformed market conditions. This report is intended to educate policymakers and stakeholders on beneficial reforms that will keep interconnection processes efficient and cost-effective while maintaining a safe and reliable power system.

Coddington, M.; Fox, K.; Stanfield, S.; Varnado, L.; Culley, T.; Sheehan, M.

2012-12-01T23:59:59.000Z

79

The evolution and adoption of optical interconnect cables  

E-Print Network [OSTI]

Optical technologies are now ubiquitous in data communication, telecommunication, and computing networks for transmission distances beyond a few meters. The use of optical to transmit voice communication has changed the ...

Chiao, Louisa

2011-01-01T23:59:59.000Z

80

Learn More About Interconnections | Department of Energy  

Broader source: Energy.gov (indexed) [DOE]

About Interconnections Learn More About Interconnections EASTERN INTERCONNECTION North America is comprised of two major and three minor alternating current (AC) power grids or...

Note: This page contains sample records for the topic "adopted interconnection standards" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


81

Capillary interconnect device  

DOE Patents [OSTI]

An interconnecting device for connecting a plurality of first fluid-bearing conduits to a corresponding plurality of second fluid-bearing conduits thereby providing fluid communication between the first fluid-bearing conduits and the second fluid-bearing conduits. The device includes a manifold and one or two ferrule plates that are held by compressive axial forces.

Renzi, Ronald F

2013-11-19T23:59:59.000Z

82

QCD Interconnection Effects  

E-Print Network [OSTI]

Heavy objects like the W, Z and t are short-lived compared with typical hadronization times. When pairs of such particles are produced, the subsequent hadronic decay systems may therefore become interconnected. We study such potential effects at Linear Collider energies.

TorbjŲrn SjŲstrand

1999-10-09T23:59:59.000Z

83

QCD Interconnection Effects  

E-Print Network [OSTI]

Heavy objects like the W, Z and t are short-lived compared with typical hadronization times. When pairs of such particles are produced, the subsequent hadronic decay systems may therefore become interconnected. We study such potential effects at Linear Collider energies.

TorbjŲrn SjŲstrand; Valery A. Khoze

1999-08-19T23:59:59.000Z

84

VLSI interconnect Avinoam Kolodny  

E-Print Network [OSTI]

1000 10000 100000 Length [um] Power Local total Global total TOTAL globallocal Power Distribution by Wirelength · Total Dynamic Power · Global clock ­ not included · Local signals nets = 66% · Global signals global signals Total dynamic power (Gate, Diffusion and Interconnect) local clock global signals global

Kolodny, Avinoam

85

North American Electric Reliability Corporation Interconnections...  

Office of Environmental Management (EM)

North American Electric Reliability Corporation Interconnections North American Electric Reliability Corporation Interconnections Map of the North American Electric Reliability...

86

Updating Interconnection Screens for PV System Integration  

SciTech Connect (OSTI)

This white paper evaluates the origins and usefulness of the capacity penetration screen, offer short-term solutions which could effectively allow fast-track interconnection to many PV system applications, and considers longer-term solutions for increasing PV deployment levels in a safe and reliable manner while reducing or eliminating the emphasis on the penetration screen. Short-term and longer-term alternatives approaches are offered as examples; however, specific modifications to screening procedures should be discussed with stakeholders and must ultimately be adopted by state and federal regulatory bodies.

Coddington, M.; Mather, B.; Kroposki, B.; Lynn, K.; Razon, A.; Ellis, A.; Hill, R.; Key, T.; Nicole, K.; Smith, J.

2012-02-01T23:59:59.000Z

87

GSA-Utility Interconnection Agreements  

Broader source: Energy.gov [DOE]

Presentationógiven at at the Fall 2012 Federal Utility Partnership Working Group (FUPWG) meetingócovers the General Service Administration's (GSA's) utility interconnection agreements.

88

Interconnection Agreements for Onsite Generation  

Broader source: Energy.gov [DOE]

Presentation covers Interconnection Agreements for Onsite Generation and is given at the Spring 2011 Federal Utility Partnership Working Group (FUPWG) meeting.

89

HR Department ADOPTION LEAVE  

E-Print Network [OSTI]

who become adoptive parents after 6 April 2003 are entitled to adoption leave and to receive Statutory by exception from one leave year to another. Unused annual leave may be lost. Annual leave will continue;PATERNITY LEAVE FOR ADOPTION Paternity leave is granted to eligible adoptive parents where a child

Doran, Simon J.

90

Process for electrically interconnecting electrodes  

DOE Patents [OSTI]

Electrical interconnects for solar cells or other electronic components using a silver-silicone paste or a lead-tin (Pb--Sn) no-clean fluxless solder cream, whereby the high breakage of thin (<6 mil thick) solar cells using conventional solder interconnect is eliminated. The interconnects of this invention employs copper strips which are secured to the solar cells by a silver-silicone conductive paste which can be used at room temperature, or by a Pb--Sn solder cream which eliminates undesired residue on the active surfaces of the solar cells. Electrical testing using the interconnects of this invention has shown that no degradation of the interconnects developed under high current testing, while providing a very low contact resistance value.

Carey, Paul G. (Mountain View, CA); Thompson, Jesse B. (Brentwood, CA); Colella, Nicolas J. (Livermore, CA); Williams, Kenneth A. (Livermore, CA)

2002-01-01T23:59:59.000Z

91

Optically Interconnected MulticomputersUsing  

E-Print Network [OSTI]

Optically Interconnected MulticomputersUsing Inverted-GraphTopologies Tosuccessfullyexploitthebenefitsofopticaltechnologyinatightlycoupledmulticomputer, the architecturaldesignmust reflectboth the advantages and limitationsof optics. This article systems. Although optics have con- tributed dramatically to long-distance communi- cation and more

Krchnavek, Robert R.

92

Renewable Systems Interconnection: Executive Summary  

SciTech Connect (OSTI)

The U.S. Department of Energy launched the Renewable Systems Interconnection (RSI) study in 2007 to address the challenges to high penetrations of distributed renewable energy technologies. The RSI study consists of 14 additional reports.

Kroposki, B.; Margolis, R.; Kuswa, G.; Torres, J.; Bower, W.; Key, T.; Ton, D.

2008-02-01T23:59:59.000Z

93

Analysis of interconnect microstrip lines  

E-Print Network [OSTI]

of the return loss of the slot-coupled microstrip dipole. Section C presents two simulations of the return loss on the slot- coupled rectangular patch antenna. A. Interconnect of Microstrip Lines Several circuits with the geometry of Figure 1 were fabricated.... Experimental and Theoretical Results of the Interconnect Two circuits were designed and fabricated. Each circuit consists of two substrates as shown in Figure 9. One substrate has an open microstrip line etched in one side and an aperture etched...

Luong, Giam-Minh

1992-01-01T23:59:59.000Z

94

Modeling and Analysis of Large-Scale On-Chip Interconnects  

E-Print Network [OSTI]

in computer aided design areas. This dissertation presents new methodologies for addressing the above two important challenging issues for large scale on-chip interconnect modeling and analysis: In the past, the standard statistical circuit modeling techniques...

Feng, Zhuo

2010-07-14T23:59:59.000Z

95

Reliability of copper interconnects in integrated circuits  

E-Print Network [OSTI]

As dimensions shrink and current densities increase, the reliability of metal interconnects becomes a serious concern. In copper interconnects, the dominant diffusion path is along the interface between the copper and the ...

Choi, Zung-Sun

2007-01-01T23:59:59.000Z

96

Sandia National Laboratories: Permitting, Inspection, and Interconnect...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Tagged with: Energy * Inspecting * Interconnection * Permitting * photovoltaic * Photovoltaics * PV * Renewable Energy * solar * Solar Energy * Solar Market Transformation *...

97

Interconnection of on-site photovoltaic generation to the electric utility. [Conference paper  

SciTech Connect (OSTI)

Electrical interconnection with the local electric utility of small, privately owned, on-site photovoltaic generating systems will be necessary. Legal guidelines exist through PURPA, administered by FERC, to establish interconnection, but economic viability will be the deciding factor in constructing photovoltaic generating systems. Although nationally recognized technical standards do not yet exist for interconnecting photovoltaic generation with an electric utility, most utilities have considered the need for developing cogeneration standards, and a few have developed such standards independently. Additional costs incurred by utilities in providing service interconnections to customers with cogeneration will be passed along to those customers, either as a direct assessment or as part of the applicable rate schedule. An economic-analysis methodology has been developed to allow comparing various possible photovoltaic-generating-system configurations under different utility rate structures and varying economic climates on a consistent basis.

Eichler, C.H.; Kilar, L.A.; Stiller, P.H.

1980-01-01T23:59:59.000Z

98

New Report Characterizes Existing Offshore Wind Grid Interconnection...  

Office of Environmental Management (EM)

New Report Characterizes Existing Offshore Wind Grid Interconnection Capabilities New Report Characterizes Existing Offshore Wind Grid Interconnection Capabilities September 3,...

99

Flexible interconnects for fuel cell stacks  

DOE Patents [OSTI]

An interconnect that facilitates electrical connection and mechanical support with minimal mechanical stress for fuel cell stacks. The interconnects are flexible and provide mechanically robust fuel cell stacks with higher stack performance at lower cost. The flexible interconnects replace the prior rigid rib interconnects with flexible "fingers" or contact pads which will accommodate the imperfect flatness of the ceramic fuel cells. Also, the mechanical stress of stacked fuel cells will be smaller due to the flexibility of the fingers. The interconnects can be one-sided or double-sided.

Lenz, David J.; Chung, Brandon W.; Pham, Ai Quoc

2004-11-09T23:59:59.000Z

100

Internship Guidelines Adopted 2001  

E-Print Network [OSTI]

Internship Guidelines Adopted 2001 Revised February 2004 Revised March 15, 2007 Page 1 of 5 INTERNSHIP GUIDELINES College of Business Louisiana Tech University The University supports an experiential an internship course(s) that students may apply as credit toward their academic degrees. The internship must

Selmic, Sandra

Note: This page contains sample records for the topic "adopted interconnection standards" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


101

Interconnect  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May JunDatastreamsmmcrcalgovInstrumentsruc DocumentationP-SeriesFlickrinformation for and NovelFEG-SEM with0,

102

Double interconnection fuel cell array  

DOE Patents [OSTI]

A fuel cell array is made, containing number of tubular, elongated fuel cells which are placed next to each other in rows (A, B, C, D), where each cell contains inner electrodes and outer electrodes, with solid electrolyte between the electrodes, where the electrolyte and outer electrode are discontinuous, having two portions, and providing at least two opposed discontinuities which contain at least two oppositely opposed interconnections contacting the inner electrode, each cell having only three metallic felt electrical connectors which contact surrounding cells, where each row is electrically connected to the other. 5 figures.

Draper, R.; Zymboly, G.E.

1993-12-28T23:59:59.000Z

103

Recent Development of SOFC Metallic Interconnect  

SciTech Connect (OSTI)

Interest in solid oxide fuel cells (SOFC) stems from their higher eĪciencies and lower levels of emitted pollu- tants, compared to traditional power production methods. Interconnects are a critical part in SOFC stacks, which connect cells in series electrically, and also separate air or oxygen at the cathode side from fuel at the anode side. Therefore, the requirements of interconnects are the most demanding, i:e:, to maintain high elec- trical conductivity, good stability in both reducing and oxidizing atmospheres, and close coeĪcient of thermal expansion (CTE) match and good compatibility with other SOFC ceramic components. The paper reviewed the interconnect materials, and coatings for metallic interconnect materials.

Wu JW, Liu XB

2010-04-01T23:59:59.000Z

104

NREL: Technology Deployment - Distributed Generation Interconnection...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Distributed Generation Interconnection Collaborative Become a Member DGIC members are included in quarterly informational meetings and discussions related to distributed PV...

105

Updating Interconnection Screens for PV System Integration  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Abraham Ellis, Roger Hill Sandia National Laboratories Tom Key, Kristen Nicole, Jeff Smith Electric Power Research Institute Updating Interconnection Screens for PV System...

106

Voltage Collapse SimulationVoltage Collapse Simulation (Eastern Interconnection(Eastern Interconnection  

E-Print Network [OSTI]

PSERC Voltage Collapse SimulationVoltage Collapse Simulation (Eastern Interconnection(Eastern Interconnection Scenario)Scenario) Simulation Prepared by Dennis J. RaySimulation Prepared by Dennis J. Ray Interconnection based on a series of generator and line outages. An actual voltage collapse may not occur due

107

IEEE 1547 and 2030 Standards for Distributed Energy Resources...  

Office of Scientific and Technical Information (OSTI)

IEEE 1547 and 2030 Standards for Distributed Energy Resources Interconnection and Interoperability with the Electricity Grid Thomas Basso National Renewable Energy Laboratory...

108

Pricing in Information-Centric Network Interconnection  

E-Print Network [OSTI]

--ICN interconnection, economic incentives, col- laborative caching, non-cooperative games, network pricing. I economic incentives for caching and sharing content in ICN interconnection. For example, an ISP provider Engineering Department, ETH Zurich, Switzerland Abstract--We propose a pricing model to study the economic

Paris-Sud XI, Universitť de

109

FPGA Interconnect Delay Fault Testing Erik Chmelar  

E-Print Network [OSTI]

A satisfactory FPGA testing method meets several crite- ria. First, the routing resources must be explicitlyFPGA Interconnect Delay Fault Testing Erik Chmelar Center for Reliable Computing Stanford is a scalable manufactur- ing test method for all SRAM-based FPGAs, able to detect multiple interconnect delay

Stanford University

110

EPRI PEAC Corp.: Certification Model Program and Interconnection Agreement Tools  

SciTech Connect (OSTI)

Summarizes the work of EPRI PEAC Corp., under contract to DOE's Distribution and Interconnection R&D, to develop a certification model program and interconnection agreement tools to support the interconnection of distributed energy resources.

Not Available

2003-10-01T23:59:59.000Z

111

STANDARD LAN -1 Fiber Channel  

E-Print Network [OSTI]

STANDARD LAN - 1 Fiber Channel Gruppo Reti TLC nome.cognome@polito.it http://www.telematica.polito.it/ #12;STANDARD LAN - 2 Fibre Channel · Born to interconnect mainframes and servers to storage systems: fibERs, but not only... · Interoperability with SCSI, Internet Protocol (IP), ... · Standard ANSI X3

Mellia, Marco

112

Electrically long vertical interconnects for microwave circuits and antennas  

E-Print Network [OSTI]

Interconnect. . Microstrip Orientation for the Coaxial Interconnect. . . The Microstrip to Coax Transition in Fidelity Original Transition Model New Transition Model 450 mil Stub Transition Response, Transition Capacitance Using the Stub Method. 10... Transition Response (1, =20 mils, w, =60 mila) . . . . 1000 mil Coaxial Line Response . . . The Full Coaxial Interconnect in Fidelity. . Coaxial Interconnect Items in Fidelity Final Simulated Coaxial Interconnect Response The Coaxial Interconnect Test...

Coutant, Matthew Richard

2000-01-01T23:59:59.000Z

113

The regulation of internet interconnection : assessing network market power  

E-Print Network [OSTI]

Interconnection agreements in the telecommunications industry have always been constrained by regulation. Internet interconnection has not received the same level of scrutiny. Recent debates regarding proposed mergers, ...

Maida, Elisabeth M. (Elisabeth Marigo)

2013-01-01T23:59:59.000Z

114

Renewable Generation and Interconnection to the Electrical Grid...  

Broader source: Energy.gov (indexed) [DOE]

Generation and Interconnection to the Electrical Grid in Southern California Renewable Generation and Interconnection to the Electrical Grid in Southern California Presentation...

115

U.S. Virgin Islands Establishes Interconnection Standards to Clear the Way for Grid Interconnection  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious Rank EERE:YearRound-Up from theDepartment of Dept. of Energy, Office ofNuclear WeaponstoU.S. ThreatenedU.S.

116

Electromigration kinetics and critical current of Pb-free interconnects  

SciTech Connect (OSTI)

Electromigration kinetics of Pb-free solder bump interconnects have been studied using a single bump parameter sweep technique. By removing bump to bump variations in structure, texture, and composition, the single bump sweep technique has provided both activation energy and power exponents that reflect atomic migration and interface reactions with fewer samples, shorter stress time, and better statistics than standard failure testing procedures. Contact metallurgies based on Cu and Ni have been studied. Critical current, which corresponds to the Blech limit, was found to exist in the Ni metallurgy, but not in the Cu metallurgy. A temperature dependence of critical current was also observed.

Lu, Minhua; Rosenberg, Robert [IBM T. J. Watson Research Center, Yorktown Heights, New York 10598 (United States)

2014-04-07T23:59:59.000Z

117

Carbon nanotube interconnects for IC chips  

E-Print Network [OSTI]

Carbon nanotubes (CNTs) have been investigated as candidate materials to replace or augment the existing copper-based technologies as interconnects for Integrated Circuit (IC) chips. Being ballistic conductors, CNTs are ...

Anwar Ali, Hashina Parveen

2006-01-01T23:59:59.000Z

118

Carbon nanotube synthesis for integrated circuit interconnects  

E-Print Network [OSTI]

Based on their properties, carbon nanotubes (CNTs) have been identified as ideal replacements for copper interconnects in integrated circuits given their higher current density, inertness, and higher resistance to ...

Nessim, Gilbert Daniel

2009-01-01T23:59:59.000Z

119

NREL Variability Analysis for the Western Interconnect (Presentation)  

SciTech Connect (OSTI)

This presentation investigates the effects of several Energy Imbalance Markets implementations in the Western Interconnect.

Milligan, M.; Kirby, B.; King, J.

2011-07-01T23:59:59.000Z

120

Accelerating Fatigue Testing for Cu Ribbon Interconnects (Presentation)  

SciTech Connect (OSTI)

This presentation describes fatigue experiments and discusses dynamic mechanical loading for Cu ribbon interconnects.

Bosco, N.; Silverman, T.; Wohlgemuth , J.; Kurtz, S.; Inoue, M.; Sakurai, K.; Shioda, T.; Zenkoh, H.; Miyashita, M.; Tadanori, T.; Suzuki, S.

2013-05-01T23:59:59.000Z

Note: This page contains sample records for the topic "adopted interconnection standards" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


121

InterconnectFabric InterconnectFabric SingleBuilding Multi-Building  

E-Print Network [OSTI]

Interconnects in Datacenter Networks Opportunities and Challenges for WDM Hong Liu, Cedric F. Lam, and Chris We review the growing need for optical interconnect bandwidth in datacenter networks growth inside datacenter networks. INTRODUCTION The rapid growth of Internet and cloud computing

Tomkins, Andrew

122

Accelerating Clean Energy Adoption (Fact Sheet), Weatherization...  

Broader source: Energy.gov (indexed) [DOE]

Accelerating Clean Energy Adoption (Fact Sheet), Weatherization and Intergovernmental Program (WIP) Accelerating Clean Energy Adoption (Fact Sheet), Weatherization and...

123

Using Interconnected Texts to Highlight Culture in the Foreign Language Classroom  

E-Print Network [OSTI]

in analyzing this interconnectivity, teachers should deviseon the nature of interconnectivity in their everydaywill look for the interconnectivity of texts in other

Smith, Maya

2013-01-01T23:59:59.000Z

124

California Energy Commission ADOPTED REGULATIONS  

E-Print Network [OSTI]

California Energy Commission ADOPTED REGULATIONS FEBRUARY 2013 CEC-400-2010-004-CMF NONRESIDENTIAL BUILDING ENERGY USE DISCLOSURE PROGRAM Proposed Regulations: California Code of Regulations, Title 20, Division 2, Chapter 4, Article 9, Sections 1680 1685 CALIFORNIA ENERGY COMMISSION Edmund

125

SciTech Connect: IEEE 1547 and 2030 Standards for Distributed...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Standards for Distributed Energy Resources Interconnection and Interoperability with the Electricity Grid Public-private partnerships have been a mainstay of the U.S. Department...

126

Original Paper Fully interconnected, linear control  

E-Print Network [OSTI]

Original Paper Fully interconnected, linear control for limit cycle walking Joseph H Solomon1 and simple control methodologies for these models (Collins & Ruina, 2005; Hobbelen & Wisse, 2008a, 2008b. Corresponding author: Joseph H. Solomon, Northwestern University, Department of Mechanical Engineering, 2145

Hartmann, Mitra J. Z.

127

Asynchronous intrusion recovery for interconnected web services  

E-Print Network [OSTI]

Asynchronous intrusion recovery for interconnected web services Ramesh Chandra, Taesoo Kim, and tracking down and recovering from such an attack re- quires significant manual effort. Web services for such web services. Aire addresses several challenges, such as propagating repair across services when some

Sabatini, David M.

128

QCD Interconnection Studies at Linear Colliders  

E-Print Network [OSTI]

Heavy objects like the W, Z and t are short-lived compared with typical hadronization times. When pairs of such particles are produced, the subsequent hadronic decay systems may therefore become interconnected. We study such potential effects at Linear Collider energies.

Valery A. Khoze; TorbjŲrn SjŲstrand

1999-12-10T23:59:59.000Z

129

subcollector Schottky collector contact & interconnect metals  

E-Print Network [OSTI]

base collector depletion layer subcollector ohmic metal (a) base collector depletion layer Schottky metal base emitter collector collector We emitter base emitter emitter We Wc Wc (b) Schottky collector contact & interconnect metals Emitter & collector Ohmics undoped collector depletion layer base N

Rodwell, Mark J. W.

130

Fast high-order variation-aware IC interconnect analysis  

E-Print Network [OSTI]

Interconnects constitute a dominant source of circuit delay for modern chip designs. The variations of critical dimensions in modern VLSI technologies lead to variability in interconnect performance that must be fully accounted for in timing...

Ye, Xiaoji

2009-05-15T23:59:59.000Z

131

High temperature solid electrolyte fuel cell configurations and interconnections  

DOE Patents [OSTI]

High temperature fuel cell configurations and interconnections are made including annular cells having a solid electrolyte sandwiched between thin film electrodes. The cells are electrically interconnected along an elongated axial outer surface.

Isenberg, Arnold O. (Forest Hills, PA)

1984-01-01T23:59:59.000Z

132

Probing Porosity and Pore Interconnectivity in Crystalline Mesoporous...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Porosity and Pore Interconnectivity in Crystalline Mesoporous TiO2 Using Hyperpolarized Xe-129 NMR. Probing Porosity and Pore Interconnectivity in Crystalline Mesoporous TiO2 Using...

133

VLSI Interconnect Optimization Considering Non-uniform Metal Stacks  

E-Print Network [OSTI]

With the advances in process technology, comes the domination of interconnect in the overall propagation delay in modern VLSI designs. Hence, interconnect synthesis techniques, such as buffer insertion, wire sizing and layer assignment play critical...

Tsai, Jung-Tai

2013-08-01T23:59:59.000Z

134

InterConnections A Report on Interdisciplinary Computing at the  

E-Print Network [OSTI]

InterConnections A Report on Interdisciplinary Computing at the University of Maryland Institute be found on pages 6 and 7 of this issue of InterConnections. ; continued on Page 2 Science/UMIACS); (2) use

Gruner, Daniel S.

135

InterConnections A Report on Interdisciplinary Computing at the  

E-Print Network [OSTI]

InterConnections A Report on Interdisciplinary Computing at the University of Maryland Institute BY BEN SHNEIDERMANPHOTO BY BEN SHNEIDERMAN #12;2 InterConnections During the past six months, a number

Gruner, Daniel S.

136

STABILITY ANALYSIS OF INTERCONNECTED POWER SYSTEMS COUPLED WITH MARKET DYNAMICS  

E-Print Network [OSTI]

STABILITY ANALYSIS OF INTERCONNECTED POWER SYSTEMS COUPLED WITH MARKET DYNAMICS F.L. Alvarado1 J of generators and network interconnections. This paper examines questions of stability in such coupled systems

137

Solar Energy to Benefit from New FERC Interconnection Procedures...  

Energy Savers [EERE]

Solar Energy to Benefit from New FERC Interconnection Procedures Solar Energy to Benefit from New FERC Interconnection Procedures October 30, 2014 - 5:15pm Addthis As a major win...

138

Renewable Portfolio Standard  

Broader source: Energy.gov [DOE]

The New York Public Service Commission (PSC) adopted a renewable portfolio standard (RPS) in September 2004 and issued implementation rules in April 2005. As originally designed, New York's RPS had...

139

Renewable Energy Standard  

Broader source: Energy.gov [DOE]

In November 2006, the Arizona Corporation Commission (ACC) adopted [http://images.edocket.azcc.gov/docketpdf/0000063561.pdf final rules] to expand the state's Renewable Energy Standard (RES) to 15%...

140

Department of Energy Standards Index  

SciTech Connect (OSTI)

This TSL, intended for use in selecting and using DOE technical standards and other Government and non-Government standards, provides listing of current and inactive DOE technical standards, non-Government standards adopted by DOE, other Government documents in which DOE has a recorded interest, and cancelled DOE technical standards.

NONE

1995-08-01T23:59:59.000Z

Note: This page contains sample records for the topic "adopted interconnection standards" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


141

Interconnected hydro-thermal systems Models, methods, and applications  

E-Print Network [OSTI]

Interconnected hydro-thermal systems Models, methods, and applications Magnus Hindsberger Kgs. Lyngby 2003 IMM-PHD-2003-112 Interconnected hydro-thermalsystems #12;Technical University of Denmark 45882673 reception@imm.dtu.dk www.imm.dtu.dk IMM-PHD-2003-112 ISSN 0909-3192 #12;Interconnected hydro

142

COLLEGE OF COMPUTER, MATHEMATICAL AND PHYSICAL SCIENCES InterConnections  

E-Print Network [OSTI]

COLLEGE OF COMPUTER, MATHEMATICAL AND PHYSICAL SCIENCES InterConnections Contents 2 Director for large amounts of data FALL/WINTER 2007 continued on page 4... InterConnections is published. For her work on entity Lise Getoor: From Data to Information Lise Getoor #12;INTERCONNECTIONS Fall

Gruner, Daniel S.

143

Interconnecting PV on New York City's Secondary Network  

E-Print Network [OSTI]

Interconnecting PV on New York City's Secondary Network Distribution System K. Anderson, M #12;Technical Report Interconnecting PV on New York NREL/ TP-7A2-46902 City's Secondary Network of Concerns and Solutions to PV Interconnection in New York City 4.0 Utility Application Process Review 5

144

COLLEGE OF COMPUTER, MATHEMATICAL AND PHYSICAL SCIENCES InterConnections  

E-Print Network [OSTI]

COLLEGE OF COMPUTER, MATHEMATICAL AND PHYSICAL SCIENCES InterConnections Contents 2 Director Neil Spring: Mapping the Internet 12 Ramani Duriaswami: Processing Sound AUGUST 2008 InterConnections research- ers to gauge similarities and differences continued on page 2. #12;INTERCONNECTIONS AUGUST 2008

Gruner, Daniel S.

145

InterConnections A Report on Interdisciplinary Computing at the  

E-Print Network [OSTI]

InterConnections A Report on Interdisciplinary Computing at the University of Maryland Institute of InterConnections. The Center was funded two years ago through the campus enhancement initiative #12;2 InterConnections Three events took place during the past five months, each of which will have

Gruner, Daniel S.

146

DOE technical standards list: Department of Energy standards index  

SciTech Connect (OSTI)

This Department of Energy (DOE) technical standards list (TSL) has been prepared by the Office of Nuclear Safety Policy and Standards (EH-31) on the basis of currently available technical information. Periodic updates of this TSL will be issued as additional information is received on standardization documents being issued, adopted, or canceled by DOE. This document was prepared for use by personnel involved in the selection and use of DOE technical standards and other Government and non-Government standards. This TSL provides listings of current DOE technical standards, non-Government standards that have been adopted by DOE, other standards-related documents in which DOE has a recorded interest, and canceled DOE technical standards. Information on new DOE technical standards projects, technical standards released for coordination, recently published DOE technical standards, and activities of non-Government standards bodies that may be of interest to DOE is published monthly in Standards Actions.

NONE

1999-05-01T23:59:59.000Z

147

Quantum Dissipative Systems and Feedback Control Design by Interconnection  

E-Print Network [OSTI]

The purpose of this paper is to extend J.C. Willems' theory of dissipative systems to the quantum domain. This general theory, which combines perspectives from the quantum physics and control engineering communities, provides useful methods for analysis and design of dissipative quantum systems. We describe the interaction of the plant and a class of exosystems in general quantum feedback network terms. Our results include an infinitesimal characterization of the dissipation property, which generalizes the well-known Positive Real and Bounded Real Lemmas, and is used to study some properties of quantum dissipative systems. We also show how to formulate control design problems using quantum network models, which implements Willems' `control by interconnection' for open quantum systems. This control design formulation includes, for example, standard problems of stabilization, regulation, and robust control.

Matthew R. James; John Gough

2009-05-07T23:59:59.000Z

148

Design, analysis and simulation study of a Scalable all-Optical Interconnection Network (SCOPIN) for multiprocessing systems  

E-Print Network [OSTI]

and flexible all-optical single-hop interconnection network, called Scalable Optical Interconnection Network (SCOPIN)....

Okorafor, Ekpe Apia

2002-01-01T23:59:59.000Z

149

Scholastic Standards Scholastic Standards  

E-Print Network [OSTI]

Scholastic Standards _______________ 1.8 Page 1 Scholastic Standards Center for Advising-7095 Gaye DiGregorio, Executive Director Scholastic standards are mandated by the faculty through the Faculty Council Committee on Scholastic Standards. Procedures relative to scholastic standards

150

Release Resistant Electrical Interconnections For Mems Devices  

DOE Patents [OSTI]

A release resistant electrical interconnection comprising a gold-based electrical conductor compression bonded directly to a highly-doped polysilicon bonding pad in a MEMS, IMEMS, or MOEMS device, without using any intermediate layers of aluminum, titanium, solder, or conductive adhesive disposed in-between the conductor and polysilicon pad. After the initial compression bond has been formed, subsequent heat treatment of the joint above 363 C creates a liquid eutectic phase at the bondline comprising gold plus approximately 3 wt % silicon, which, upon re-solidification, significantly improves the bond strength by reforming and enhancing the initial bond. This type of electrical interconnection is resistant to chemical attack from acids used for releasing MEMS elements (HF, HCL), thereby enabling the use of a "package-first, release-second" sequence for fabricating MEMS devices. Likewise, the bond strength of an Au--Ge compression bond may be increased by forming a transient liquid eutectic phase comprising Au-12 wt % Ge.

Peterson, Kenneth A. (Albuquerque, NM); Garrett, Stephen E. (Albuquerque, NM); Reber, Cathleen A. (Corrales, NM)

2005-02-22T23:59:59.000Z

151

Interconnection of bundled solid oxide fuel cells  

DOE Patents [OSTI]

A system and method for electrically interconnecting a plurality of fuel cells to provide dense packing of the fuel cells. Each one of the plurality of fuel cells has a plurality of discrete electrical connection points along an outer surface. Electrical connections are made directly between the discrete electrical connection points of adjacent fuel cells so that the fuel cells can be packed more densely. Fuel cells have at least one outer electrode and at least one discrete interconnection to an inner electrode, wherein the outer electrode is one of a cathode and and anode and wherein the inner electrode is the other of the cathode and the anode. In tubular solid oxide fuel cells the discrete electrical connection points are spaced along the length of the fuel cell.

Brown, Michael; Bessette, II, Norman F; Litka, Anthony F; Schmidt, Douglas S

2014-01-14T23:59:59.000Z

152

UBC adopts energy makeover project  

E-Print Network [OSTI]

May 2011 3 UBC adopts energy makeover project 15 Max Jones makes PhD history in the Okanagan 16. This adaptation may better their odds of surviving projected rises in water temperature because of climate change. "Things like tuition, student loans, the economy, whether they'll get a job when they graduate, high cost

Farrell, Anthony P.

153

2008 BUILDING ENERGY EFFICIENCY STANDARDS  

E-Print Network [OSTI]

2008 BUILDING ENERGY EFFICIENCY STANDARDS C A L I F O R N I A E N E RGY CO M M I S S I O N Buildings and Appliances Office #12;Acknowledgments The Building Energy Efficiency Standards (Standards the adoption of the 2008 Building Energy Efficiency Standards to Jon Leber, PE, (November 13, 1947 - February

154

DOE technical standards list. Department of Energy standards index  

SciTech Connect (OSTI)

This document was prepared for use by personnel involved in the selection and use of DOE technical standards and other Government and non-Government standards. This TSL provides listing of current DOE technical standards, non-Government standards that have been adopted by DOE, other Government documents in which DOE has a recorded interest, and canceled DOE technical standards. Information on new DOE technical standards projects, technical standards released for coordination, recently published DOE technical standards, and activities of non-Government standards bodies that may be of interest to DOE is published monthly in Standards Actions.

NONE

1995-08-01T23:59:59.000Z

155

RESOLUTION NO. 2011-82 ADOPTING MODESTO IRRIGATION DISTRICT'S RENEWABLE  

E-Print Network [OSTI]

RESOLUTION NO. 2011-82 ADOPTING MODESTO IRRIGATION DISTRICT'S RENEWABLE ENERGY RESOURCES Standard (RPS) in an effort to meet 20 percent ofits retail energy sales with renewable resources by 2017 for consideration by the Board of Directors, attached hereto as Attachment A, Renewable Energy Resources Enforcement

156

624 IEEE JOURNAL ON SELECTED TOPICS IN QUANTUM ELECTRONICS, VOL. 9, NO. 2, MARCH/APRIL 2003 Optoelectronic Interconnection Technology  

E-Print Network [OSTI]

Optoelectronic Interconnection Technology in the HOLMS System Paul Lukowicz, Member, IEEE, J√ľrgen Jahns, Member. S√ľllau, J. F. Snowdon, M. Wirz, and G. Tr√∂ster Invited Paper Abstract--The High-Speed Optoelectronic and economical by developing optoelectronic packaging tech- nology compatible with standard electronic assembly

Jahns, J√ľrgen

157

Repairable chip bonding/interconnect process  

DOE Patents [OSTI]

A repairable, chip-to-board interconnect process which addresses cost and testability issues in the multi-chip modules. This process can be carried out using a chip-on-sacrificial-substrate technique, involving laser processing. This process avoids the curing/solvent evolution problems encountered in prior approaches, as well is resolving prior plating problems and the requirements for fillets. For repairable high speed chip-to-board connection, transmission lines can be formed on the sides of the chip from chip bond pads, ending in a gull wing at the bottom of the chip for subsequent solder.

Bernhardt, Anthony F. (Berkeley, CA); Contolini, Robert J. (Livermore, CA); Malba, Vincent (Livermore, CA); Riddle, Robert A. (Tracy, CA)

1997-01-01T23:59:59.000Z

158

Repairable chip bonding/interconnect process  

DOE Patents [OSTI]

A repairable, chip-to-board interconnect process which addresses cost and testability issues in the multi-chip modules is disclosed. This process can be carried out using a chip-on-sacrificial-substrate technique, involving laser processing. This process avoids the curing/solvent evolution problems encountered in prior approaches, as well is resolving prior plating problems and the requirements for fillets. For repairable high speed chip-to-board connection, transmission lines can be formed on the sides of the chip from chip bond pads, ending in a gull wing at the bottom of the chip for subsequent solder. 10 figs.

Bernhardt, A.F.; Contolini, R.J.; Malba, V.; Riddle, R.A.

1997-08-05T23:59:59.000Z

159

Interconnecting gold islands with DNA origami  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May JunDatastreamsmmcrcalgovInstrumentsruc DocumentationP-SeriesFlickrinformation for and NovelFEG-SEM with0,Interconnecting gold islands

160

Environmental Regulation Impacts on Eastern Interconnection Performance  

SciTech Connect (OSTI)

In the United States, recent environmental regulations will likely result in the removal of nearly 30 GW of oil and coal-fired generation from the power grid, mostly in the Eastern Interconnection (EI). The effects of this transition on voltage stability and transmission line flows have previously not been studied from a system-wide perspective. This report discusses the results of power flow studies designed to simulate the evolution of the EI over the next few years as traditional generation sources are replaced with environmentally friendlier ones such as natural gas and wind.

Markham, Penn N [ORNL; Liu, Yilu [ORNL; Young II, Marcus Aaron [ORNL

2013-07-01T23:59:59.000Z

Note: This page contains sample records for the topic "adopted interconnection standards" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


161

Flip chip electrical interconnection by selective electroplating and bonding  

E-Print Network [OSTI]

on a glass substrate made of 500/2000 A¬į of Cr/Au with 3150 lm in length and 10 lm in width. Two silicon. The interconnection chip has 102 Cr/Au interconnection lines with 3150 lm in length and 10 lm in width. The bonding pads on the ends of the interconnection lines are 40 lm by 40 lm. A 0.8 lm thick layer of aluminum

Lin, Liwei

162

Impact of High Solar Penetration in the Western Interconnection  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Impact of High Solar Penetration in the Western Interconnection Debra Lew National Renewable Energy Laboratory Nicholas Miller, Kara Clark, Gary Jordan, and Zhi Gao GE Energy...

163

Response from PJM Interconnection LLC and Pepco to Department...  

Broader source: Energy.gov (indexed) [DOE]

PJM Interconnection LLC and Pepco to Department of Energy Request for Information Concerning the Potential Need for Potomac River Station Generation Response from PJM...

164

Pepco and PJM Interconnection Comments on District of Columbia...  

Broader source: Energy.gov (indexed) [DOE]

Pepco and PJM Interconnection Comments on District of Columbia Public Service Commission, Docket No. EO-05-01 Comments and Answer to Requests for Rehearing Pepco and PJM...

165

Microgrid V2G Charging Station Interconnection Testing (Presentation)  

SciTech Connect (OSTI)

This presentation by Mike Simpson of the National Renewable Energy Laboratory (NREL) describes NREL's microgrid vehicle-to-grid charging station interconnection testing.

Simpson, M.

2013-07-01T23:59:59.000Z

166

Optimization of solid oxide fuel cell interconnect design.  

E-Print Network [OSTI]

??Performance of solid oxide fuel cells (SOFC) is dependent of a set of complex physical and chemical processes occurring simultaneously. Interconnect for SOFC is importantÖ (more)

Pulagam, Krishna C.

2009-01-01T23:59:59.000Z

167

Proposed rule for Interconnection for Wind Energy and Other Alternativ...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

REGULATORY COMMISSION 18 CFR Part 35 (Docket No. RM05-4-000) Interconnection for Wind Energy and Other Alternative Technologies (January 24, 2005) AGENCY: Federal Energy...

168

Utility Wind Integration Group Distributed Wind/Solar Interconnection Workshop  

Broader source: Energy.gov [DOE]

This two-day workshop will answer your questions about interconnecting wind and solar plants and other distributed generation applications to electric distribution systems while providing insight...

169

National Offshore Wind Energy Grid Interconnection Study  

SciTech Connect (OSTI)

The National Offshore Wind Energy Grid Interconnection Study (NOWEGIS) considers the availability and potential impacts of interconnecting large amounts of offshore wind energy into the transmission system of the lower 48 contiguous United States. A total of 54GW of offshore wind was assumed to be the target for the analyses conducted. A variety of issues are considered including: the anticipated staging of offshore wind; the offshore wind resource availability; offshore wind energy power production profiles; offshore wind variability; present and potential technologies for collection and delivery of offshore wind energy to the onshore grid; potential impacts to existing utility systems most likely to receive large amounts of offshore wind; and regulatory influences on offshore wind development. The technologies considered the reliability of various high-voltage ac (HVAC) and high-voltage dc (HVDC) technology options and configurations. The utility system impacts of GW-scale integration of offshore wind are considered from an operational steady-state perspective and from a regional and national production cost perspective.

Daniel, John P. [ABB Inc; Liu, Shu [ABB Inc; Ibanez, Eduardo [National Renewable Energy Laboratory; Pennock, Ken [AWS Truepower; Reed, Greg [University of Pittsburgh; Hanes, Spencer [Duke Energy

2014-07-30T23:59:59.000Z

170

Reactive power interconnection requirements for PV and wind plants : recommendations to NERC.  

SciTech Connect (OSTI)

Voltage on the North American bulk system is normally regulated by synchronous generators, which typically are provided with voltage schedules by transmission system operators. In the past, variable generation plants were considered very small relative to conventional generating units, and were characteristically either induction generator (wind) or line-commutated inverters (photovoltaic) that have no inherent voltage regulation capability. However, the growing level of penetration of non-traditional renewable generation - especially wind and solar - has led to the need for renewable generation to contribute more significantly to power system voltage control and reactive power capacity. Modern wind-turbine generators, and increasingly PV inverters as well, have considerable dynamic reactive power capability, which can be further enhanced with other reactive support equipment at the plant level to meet interconnection requirements. This report contains a set of recommendations to the North-America Electricity Reliability Corporation (NERC) as part of Task 1-3 (interconnection requirements) of the Integration of Variable Generation Task Force (IVGTF) work plan. The report discusses reactive capability of different generator technologies, reviews existing reactive power standards, and provides specific recommendations to improve existing interconnection standards.

McDowell, Jason (General Electric, Schenectady, NY); Walling, Reigh (General Electric, Schenectady, NY); Peter, William (SunPower, Richmond, CA); Von Engeln, Edi (NV Energy, Reno, NV); Seymour, Eric (AEI, Fort Collins, CO); Nelson, Robert (Siemens Wind Turbines, Orlando, FL); Casey, Leo (Satcon, Boston, MA); Ellis, Abraham; Barker, Chris. (SunPower, Richmond, CA)

2012-02-01T23:59:59.000Z

171

COLLEGE OF COMPUTER, MATHEMATICAL AND PHYSICAL SCIENCES InterConnections  

E-Print Network [OSTI]

COLLEGE OF COMPUTER, MATHEMATICAL AND PHYSICAL SCIENCES InterConnections Contents 2 Director- tious diseases and water issues.The network would include research from scientists in coun- InterConnections.V.Williams Bldg. University of Maryland College Park, MD 20742-3251 Phone: 301.405.6722 #12;INTERCONNECTIONS

Gruner, Daniel S.

172

Solid-state energy storage module employing integrated interconnect board  

DOE Patents [OSTI]

An electrochemical energy storage device includes a number of solid-state thin-film electrochemical cells which are selectively interconnected in series or parallel through use of an integrated interconnect board. The interconnect board is typically disposed within a sealed housing which also houses the electrochemical cells, and includes a first contact and a second contact respectively coupled to first and second power terminals of the energy storage device. The interconnect board advantageously provides for selective series or parallel connectivity with the electrochemical cells, irrespective of electrochemical cell position within the housing. Fuses and various electrical and electro-mechanical devices, such as bypass, equalization, and communication devices for example, may also be mounted to the interconnect board and selectively connected to the electrochemical cells.

Rouillard, Jean; Comte, Christophe; Daigle, Dominik; Hagen, Ronald A.; Knudson, Orlin B.; Morin, Andre; Ranger, Michel; Ross, Guy; Rouillard, Roger; St-Germain, Philippe; Sudano, Anthony; Turgeon, Thomas A.

2004-09-28T23:59:59.000Z

173

Solid-state energy storage module employing integrated interconnect board  

DOE Patents [OSTI]

The present invention is directed to an improved electrochemical energy storage device. The electrochemical energy storage device includes a number of solid-state, thin-film electrochemical cells which are selectively interconnected in series or parallel through use of an integrated interconnect board. The interconnect board is typically disposed within a sealed housing which also houses the electrochemical cells, and includes a first contact and a second contact respectively coupled to first and second power terminals of the energy storage device. The interconnect board advantageously provides for selective series or parallel connectivity with the electrochemical cells, irrespective of electrochemical cell position within the housing. Fuses and various electrical and electromechanical devices, such as bypass, equalization, and communication devices for example, may also be mounted to the interconnect board and selectively connected to the electrochemical cells.

Rouillard, Jean; Comte, Christophe; Daigle, Dominik; Hagen, Ronald A.; Knudson, Orlin B.; Morin, Andre; Ranger, Michel; Ross, Guy; Rouillard, Roger; St-Germain, Philippe; Sudano, Anthony; Turgeon, Thomas A.

2003-11-04T23:59:59.000Z

174

A High-Performance Optoelectronic Interconnect Router: Using Increased Bandwidth to Enable Latency Reduction  

E-Print Network [OSTI]

D R A FT 1 A High-Performance Optoelectronic Interconnect Router: Using Increased Bandwidth optoelectronic interconnection network router capable of supplying and efficiently utilizing higher bandwidth routing, interconnection network, latency hiding/reduction techniques, optoelectronic router. 1

Pinkston, Timothy M.

175

Near-Bulk Conductivity of Gold Nanowires as Nanoscale Interconnects and the Role of Atomically  

E-Print Network [OSTI]

Near-Bulk Conductivity of Gold Nanowires as Nanoscale Interconnects and the Role of Atomically, a significant portion of the chip is composed of interconnects. Besides, the engineering problems associated loss, signal degradation, interconnection delays, and other performance limitations related

Zubarev, Eugene

176

A SURVEY OF STATE-LEVEL COST ESTIMATES OF RENEWABLES PORTFOLIO STANDARDS  

E-Print Network [OSTI]

LEVEL COST ESTIMATES OF RENEWABLES PORTFOLIO STANDARDS Galenthe incremental cost of renewables portfolio standards (RPS)Washington DC have adopted renewables portfolio standards (

Barbose, Galen

2014-01-01T23:59:59.000Z

177

Got Standards? "Got Standards?"  

E-Print Network [OSTI]

9000 standards were developed by the International Organization for Standardization, which was founded in 1946. The purpose of the organization was to promote the development of international standards in order to bring harmony to global standards for international trade. Enter ISO 9000. The Basics In order

Vardeman, Stephen B.

178

Energy and water in the Western and Texas interconnects.  

SciTech Connect (OSTI)

The Department of Energy's Office of Electricity has initiated a $60M program to assist the electric industry in interconnection-level analysis and planning. The objective of this effort is to facilitate the development or strengthening of capabilities in each of the three interconnections serving the lower 48 states of the United States, to prepare analyses of transmission requirements under a broad range of alternative futures and develop long-term interconnection-wide transmission expansion plans. The interconnections are the Western Interconnection, the Eastern Interconnection, and the Texas Interconnection. One element of this program address the support and development of an integrated energy-water Decision Support System (DSS) that will enable planners in the Western and Texas Interconnections to analyze the potential implications of water stress for transmission and resource planning (the Eastern Interconnection is not participating in this element). Specific objectives include: (1) Develop an integrated Energy-Water Decision Support System (DSS) that will enable planners in the Western and Texas Interconnections to analyze the potential implications of water stress for transmission and resource planning. (2) Pursue the formulation and development of the Energy-Water DSS through a strongly collaborative process between members of this proposal team and the Western Electricity Coordinating Council (WECC), Western Governors Association (WGA), the Electric Reliability Council of Texas (ERCOT) and their associated stakeholder teams. (3) Exercise the Energy-Water DSS to investigate water stress implications of the transmission planning scenarios put forward by WECC, WGA, and ERCOT. The goals of this project are: (1) Develop an integrated Energy-Water Decision Support System (DSS) that will enable planners to analyze the potential implications of water stress for transmission and resource planning. (2) Pursue the formulation and development of the Energy-Water DSS through a strongly collaborative process between Western Electricity Coordinating Council, Electric Reliability Council of Texas, Western Governors Association, and Western States Water Council. (3) Exercise the Energy-Water DSS to investigate water transmission planning scenarios.

Tidwell, Vincent Carroll

2010-08-01T23:59:59.000Z

179

Energy Codes and Standards: Facilities  

SciTech Connect (OSTI)

Energy codes and standards play a vital role in the marketplace by setting minimum requirements for energy-efficient design and construction. They outline uniform requirements for new buildings as well as additions and renovations. This article covers basic knowledge of codes and standards; development processes of each; adoption, implementation, and enforcement of energy codes and standards; and voluntary energy efficiency programs.

Bartlett, Rosemarie; Halverson, Mark A.; Shankle, Diana L.

2007-01-01T23:59:59.000Z

180

DOE technical standards list: Department of Energy standards index  

SciTech Connect (OSTI)

This technical standards list (TSL) was prepared for use by personnel involved in the selection and use of US DOE technical standards and other government and non-government standards. This TSL provides listings of current DOE technical standards, non-government standards that have been adopted by DOE, other government documents in which DOE has a recorded interest, and cancelled DOE technical standards. Standards are indexed by type in the appendices to this document. Definitions of and general guidance for the use of standards are also provided.

NONE

1997-06-01T23:59:59.000Z

Note: This page contains sample records for the topic "adopted interconnection standards" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


181

CITY OF GRIDLEY ADOPTION OF THE CITY OF GRIDLEY RENEWABLE ENERGY PROCUREMENT AND  

E-Print Network [OSTI]

establishes minimum quantities of renewable energy resources that load serving entities must procureCITY OF GRIDLEY ADOPTION OF THE CITY OF GRIDLEY RENEWABLE ENERGY PROCUREMENT AND ENFORCEMENT will consider the adoption of the City of Gridley Electric Renewable Portfolio Standard Procurement

182

Orange County- Wind Permitting Standards  

Broader source: Energy.gov [DOE]

In December 2010, the County of Orange Board of Supervisors adopted small wind performance and development standards (Ord. No. 10-020) in order to promote distributed generation systems in non...

183

E-Print Network 3.0 - attach interconnection technology Sample...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Barbara; NONE Collection: Biology and Medicine ; Engineering 7 Call for Papers Optoelectronic Interconnects XII (OE113) Summary: interconnect technologies ultra-short reach...

184

Exact Coupling Threshold for Structural Transition in Interconnected Networks  

E-Print Network [OSTI]

Interconnected networks are mathematical representation of systems where two or more simple networks are coupled to each other. Depending on the coupling weight between the two components, the interconnected network can function in two regimes: one where the two networks are structurally distinguishable, and one where they are not. The coupling threshold--denoting this structural transition--is one of the most crucial concepts in interconnected networks. Yet, current information about the coupling threshold is limited. This letter presents an analytical expression for the exact value of the coupling threshold and outlines network interrelation implications.

Sahneh, Faryad Darabi; Van Mieghem, Piet

2014-01-01T23:59:59.000Z

185

Characterizing opportunities for short reach optical interconnect adoption : a market survey and total cost of ownership model approach  

E-Print Network [OSTI]

Over the past decade, the demand for digital information has increased dramatically with the rising use of the Internet and various types of multimedia data - text, audio, graphics, video, and voice. As a consequence, the ...

Lindsey, Johnathan Jake, III

2010-01-01T23:59:59.000Z

186

Surface Water Quality Standards  

E-Print Network [OSTI]

recreational uses. ?The Commission will seek substantial additional public comment on any proposed changes to the standards before adopting them into the state admin- istrative code,? Davenport said. ?Because of the com- plexity and regulatory importance... Conservation Board?s state watershed coordinator, said the standards for contact recreation, with only a few exceptions, are uniformly applied regardless of water body type or the actual level of recreation use. ?Because a minimum of 10 water samples over a...

Wythe, Kathy

2007-01-01T23:59:59.000Z

187

5 F 13 Optica1 Interconnection T ransmitter Power BER  

E-Print Network [OSTI]

¬ľ 5¬ł ¬§ √ľ √? √ł √ź √ź √ļ ¬ł √? √≠ ¬ģ F√? 13 Optica1 Interconnection√? T ransmitter Power √ć BER√? √? √Ľ - ¬° √ľ √?

Choi, Woo-Young

188

Interconnecting PV on New York City's Secondary Network Distribution System  

SciTech Connect (OSTI)

This study describes technical assistance provided by NREL to help New York City and Con Edison improve the interconnection of distributed PV systems on a secondary network distribution system.

Anderson, K.; Coddington, M.; Burman, K.; Hayter, S.; Kroposki, B.; Watson, A.

2009-12-01T23:59:59.000Z

189

Energy scalability of on-chip interconnection networks  

E-Print Network [OSTI]

On-chip interconnection networks (OCN) such as point-to-point networks and buses form the communication backbone in multiprocessor systems-on-a-chip, multicore processors, and tiled processors. OCNs consume significant ...

Konstantakopoulos, Theodoros K., 1977-

2007-01-01T23:59:59.000Z

190

Evaluation of phase change materials for reconfigurable interconnects  

E-Print Network [OSTI]

The possible use of programmable integrated circuit interconnect vias using an indirectly heated phase change material is evaluated. Process development and materials investigations are examined. Devices capable of multiple ...

Khoo, Chee Ying

2010-01-01T23:59:59.000Z

191

Handshake and Circulation Flow Control in Nanaphotonic Interconnects  

E-Print Network [OSTI]

leads to low bandwidth utilization. This thesis proposes two handshake schemes for nanophotonic interconnects in CMPs, Global Handshake (GHS) and Distributed Handshake (DHS), which get rid of the traditional credit-based flow control, reduce the average...

Jayabalan, Jagadish

2012-10-19T23:59:59.000Z

192

Mortality Dependence of Cu Dual Damascene Interconnects on Adjacent Segments  

E-Print Network [OSTI]

Electromigration experiments have been carried out on straight interconnects that have single vias at each end, and are divided into two segments by a via in the center ("dotted-I" structures). For dotted-i structures in ...

Chang, Choon Wai

193

Low-Swing Signaling on Monolithically Integrated Global Graphene Interconnects  

E-Print Network [OSTI]

In this paper, we characterize the performance of monolithically integrated graphene interconnects on a prototype 0.35-?m CMOS chip. The test chip implements an array of transmitter/receivers to analyze the end-to-end data ...

Lee, Kyeong-Jae

194

The Other Face of On-Chip Interconnect  

E-Print Network [OSTI]

The multicore revolution has changed the way we think about computing. The same movement has also changed the way we look at on-chip interconnect because it is a key determinant of the performance and power efficiency of ...

Agarwal, Anant

195

Fabrication and Characterization of Through-Substrate Interconnects  

E-Print Network [OSTI]

We developed a through-substrate copper-damascene interconnect technology in silicon with minimal impedance. Via impedance was extracted using parameter measurements at 50 GHz that were matched to simple circuit models. ...

del Alamo, Jesus A.

196

Advanced Unit Commitment Strategies in the United States Eastern Interconnection  

SciTech Connect (OSTI)

This project sought to evaluate the impacts of high wind penetrations on the U.S. Eastern Interconnection and analyze how different unit commitment strategies may affect these impacts.

Meibom, P.; Larsen, H. V.; Barth, R.; Brand, H.; Tuohy, A.; Ela, E.

2011-08-01T23:59:59.000Z

197

Photovoltaic Systems Interconnected onto Secondary Network Distribution Systems Ė Success Stories  

Broader source: Energy.gov [DOE]

This report examines six case studies of photovoltaic (PV) systems integrated into secondary network systems. The six PV systems were chosen for evaluation because they are interconnected to secondary network systems located in four major Solar America Cities.

198

Interconnecting PV on NYC's Secondary Network Distribution System  

Broader source: Energy.gov [DOE]

To assess ways to improve the interconnection process, NREL conducted a four-part study with support from DOE. The NREL team then compiled the final reports from each study into this report.

199

Developing Generic Dynamic Models for the 2030 Eastern Interconnection Grid  

SciTech Connect (OSTI)

The Eastern Interconnection Planning Collaborative (EIPC) has built three major power flow cases for the 2030 Eastern Interconnection (EI) based on various levels of energy/environmental policy conditions, technology advances, and load growth. Using the power flow cases, this report documents the process of developing the generic 2030 dynamic models using typical dynamic parameters. The constructed model was validated indirectly using the synchronized phasor measurements by removing the wind generation temporarily.

Kou, Gefei [ORNL; Hadley, Stanton W [ORNL; Markham, Penn N [ORNL; Liu, Yilu [ORNL

2013-12-01T23:59:59.000Z

200

EA-1990: Ridgenose Solar Energy Interconnection Facility, Mohave County, Arizona  

Broader source: Energy.gov [DOE]

DOEís Western Area Power Administration (Desert Southwest Region) is preparing an EA that will assess the potential environmental impacts of a proposal to interconnect the planned Ridgenose Solar Energy Project to Westernís transmission system. Westernís actions could include constructing less than a mile of new transmission line from the solar facility to an existing substation, constructing an interconnection substation, and adding, moving, or modifying structures.

Note: This page contains sample records for the topic "adopted interconnection standards" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


201

Solid-state energy storage module employing integrated interconnect board  

DOE Patents [OSTI]

The present invention is directed to an improved electrochemical energy storage device. The electrochemical energy storage device includes a number of solid-state, thin-film electrochemical cells which are selectively interconnected in series or parallel through use of an integrated interconnect board. The interconnect board is typically disposed within a sealed housing which also houses the electrochemical cells, and includes a first contact and a second contact respectively coupled to first and second power terminals of the energy storage device. The interconnect board advantageously provides for selective series or parallel connectivity with the electrochemical cells, irrespective of electrochemical cell position within the housing. In one embodiment, a sheet of conductive material is processed by employing a known milling, stamping, or chemical etching technique to include a connection pattern which provides for flexible and selective interconnecting of individual electrochemical cells within the housing, which may be a hermetically sealed housing. Fuses and various electrical and electro-mechanical devices, such as bypass, equalization, and communication devices for example, may also be mounted to the interconnect board and selectively connected to the electrochemical cells.

Rouillard, Jean (Saint-Luc, CA); Comte, Christophe (Montreal, CA); Daigle, Dominik (St-Hyacinthe, CA); Hagen, Ronald A. (Stillwater, MN); Knudson, Orlin B. (Vadnais Heights, MN); Morin, Andre (Longueuil, CA); Ranger, Michel (Lachine, CA); Ross, Guy (Beloeil, CA); Rouillard, Roger (Beloeil, CA); St-Germain, Philippe (Outremont, CA); Sudano, Anthony (Laval, CA); Turgeon, Thomas A. (Fridley, MN)

2000-01-01T23:59:59.000Z

202

Modeling of customer adoption of distributed energy resources  

SciTech Connect (OSTI)

This report describes work completed for the California Energy Commission (CEC) on the continued development and application of the Distributed Energy Resources Customer Adoption Model (DER-CAM). This work was performed at Ernest Orlando Lawrence Berkeley National Laboratory (Berkeley Lab) between July 2000 and June 2001 under the Consortium for Electric Reliability Technology Solutions (CERTS) Distributed Energy Resources Integration (DERI) project. Our research on distributed energy resources (DER) builds on the concept of the microgrid ({mu}Grid), a semiautonomous grouping of electricity-generating sources and end-use sinks that are placed and operated for the benefit of its members. Although a {mu}Grid can operate independent of the macrogrid (the utility power network), the {mu}Grid is usually interconnected, purchasing energy and ancillary services from the macrogrid. Groups of customers can be aggregated into {mu}Grids by pooling their electrical and other loads, and the most cost-effective combination of generation resources for a particular {mu}Grid can be found. In this study, DER-CAM, an economic model of customer DER adoption implemented in the General Algebraic Modeling System (GAMS) optimization software is used, to find the cost-minimizing combination of on-site generation customers (individual businesses and a {mu}Grid) in a specified test year. DER-CAM's objective is to minimize the cost of supplying electricity to a specific customer by optimizing the installation of distributed generation and the self-generation of part or all of its electricity. Currently, the model only considers electrical loads, but combined heat and power (CHP) analysis capability is being developed under the second year of CEC funding. The key accomplishments of this year's work were the acquisition of increasingly accurate data on DER technologies, including the development of methods for forecasting cost reductions for these technologies, and the creation of a credible example California {mu}Grid for use in this study and in future work. The work performed during this year demonstrates the viability of DER-CAM and of our approach to analyzing adoption of DER.

Marnay, Chris; Chard, Joseph S.; Hamachi, Kristina S.; Lipman, Timothy; Moezzi, Mithra M.; Ouaglal, Boubekeur; Siddiqui, Afzal S.

2001-08-01T23:59:59.000Z

203

Jasper County Comprehensive Plan Adoption Draft  

E-Print Network [OSTI]

Jasper County Comprehensive Plan Adoption Draft Comprehensive Plan Jasper County, IN #12;#12;Table Mandate.......................................vii Jasper County's Fulfillment of the Mandate of Major Needs for Jasper County ...............5 Additional Opportunities

204

Net Metering and Interconnection Procedures-- Incorporating Best Practices  

SciTech Connect (OSTI)

State utility commissions and utilities themselves are actively developing and revising their procedures for the interconnection and net metering of distributed generation. However, the procedures most often used by regulators and utilities as models have not been updated in the past three years, in which time most of the distributed solar facilities in the United States have been installed. In that period, the Interstate Renewable Energy Council (IREC) has been a participant in more than thirty state utility commission rulemakings regarding interconnection and net metering of distributed generation. With the knowledge gained from this experience, IREC has updated its model procedures to incorporate current best practices. This paper presents the most significant changes made to IREC√?¬?√?¬Ę√?¬?√?¬?√?¬?√?¬?s model interconnection and net metering procedures.

Jason Keyes, Kevin Fox, Joseph Wiedman, Staff at North Carolina Solar Center

2009-04-01T23:59:59.000Z

205

Permitting, Interconnection, and Inspection | Department of Energy  

Broader source: Energy.gov (indexed) [DOE]

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May Jun Jul(Summary) "ofEarly Careerlumens_placard-green.epsEnergy1.pdfMarket | Department of EnergyStandardized

206

Standard interface file handbook  

SciTech Connect (OSTI)

This handbook documents many of the standard interface file formats that have been adopted by the US Department of Energy to facilitate communications between and portability of, various large reactor physics and radiation transport software packages. The emphasis is on those files needed for use of the VENTURE/PC diffusion-depletion code system. File structures, contents and some practical advice on use of the various files are provided.

Shapiro, A.; Huria, H.C. (Cincinnati Univ., OH (United States))

1992-10-01T23:59:59.000Z

207

Statewide Savings Projections from the Adoption of Commercial Building Energy Codes in Illinois  

SciTech Connect (OSTI)

ANSI/ASHRAE/IESNA Standard 90.1-1999 Energy Standard for Buildings except Low-Rise Residential Buildings was developed in an effort to set minimum requirements for the energy efficient design and construction of new commercial buildings. A number of jurisdictions in the state of Illinois are considering adopting ASHRAE 90.1-1999 as their commercial building energy code. This report builds on the results of a previous study, "Analysis of Potential Benefits and Costs of Adopting ASHRAE Standard 90.1-1999 as a Commercial Building Energy Code in Illinois Jurisdictions," to estimate the total potential impact of adopting ASHRAE 90.1-1999 as a statewide commercial building code in terms of Life-Cycle Cost (LCC) savings, total primary energy savings, and pollution emissions reductions.

Cort, Katherine A.; Belzer, David B.

2002-09-30T23:59:59.000Z

208

Hermetic aluminum radio frequency interconnection and method for making  

DOE Patents [OSTI]

The present invention provides a light-weight, hermetic coaxial radio-frequency (RF) interconnection having an electrically conductive outer housing made of aluminum or an aluminum alloy, a central electrical conductor made of ferrous or non-ferrous material, and a cylinder of dielectric material comprising a low-melting-temperature, high-thermal-expansion aluminophosphate glass composition for hermetically sealing between the aluminum-alloy outer housing and the ferrous or non-ferrous center conductor. The entire RF interconnection assembly is made permanently hermetic by thermally fusing the center conductor, glass, and housing concurrently by bringing the glass to the melt point by way of exposure to an atmospheric temperature sufficient to melt the glass, less than 540.degree. C., but that does not melt the center conductor or the outer aluminum or aluminum alloy housing. The composition of the glass used is controlled to provide a suitable low dielectric constant so that an appropriate electrical characteristic impedance, for example 50 ohms, can be achieved for an electrical interconnection that performs well at high radio frequencies and also provides an interconnection maintaining a relatively small physical size.

Kilgo, Riley D. (Albuquerque, NM); Kovacic, Larry (Albuquerque, NM); Brow, Richard K. (Rolla, MO)

2000-01-01T23:59:59.000Z

209

Energy and Reliability in Future NOC Interconnected CMPS  

E-Print Network [OSTI]

In this dissertation, I explore energy and reliability in future NoC (Network-on-Chip) interconnected CMPs (chip multiprocessors) as they have become a first-order constraint in future CMP design. In the first part, we target the root cause...

Kim, Hyungjun

2013-08-01T23:59:59.000Z

210

A Holistic Approach to Designing Energy-Efficient Cluster Interconnects  

E-Print Network [OSTI]

, new data centers in the Seattle area are forecast to increase the city's power demands by 25 percentA Holistic Approach to Designing Energy-Efficient Cluster Interconnects Eun Jung Kim, Member, IEEE--Designing energy-efficient clusters has recently become an important concern to make these systems economically

Kim, Eun Jung "EJ"

211

Optimum Wire Tapering for Minimum Power Dissipation in RLC Interconnects  

E-Print Network [OSTI]

tapering is shown to reduce the (a CMOS inverter) with the driver (a CMOS inverter). The power dissipatedOptimum Wire Tapering for Minimum Power Dissipation in RLC Interconnects Magdy A. El-Moursy and Eby G. Friedman Department of Electrical and Computer Engineering University of Rochester Rochester, New

Friedman, Eby G.

212

High-temperature quenching of electrical resistance in graphene interconnects  

E-Print Network [OSTI]

into the chip interconnect design the materials with low electrical resistance and high thermal con- ductivity dependence of the resistance were explained by the thermal generation of the electron-hole pairs and carrier, increased total thermal boundary resistance of the chip layers, incorporation of the alternative dielectric

213

Dynamic management of water transfer between two interconnected river basins  

E-Print Network [OSTI]

Dynamic management of water transfer between two interconnected river basins Francisco Cabo Katrin cause environmental damage in the donor basin. The recipient faces a trade-off between paying the price of the irrigated soil, or demand for water for highly productive activities like tourism), then the existence

Boyer, Edmond

214

Electric power from offshore wind via synoptic-scale interconnection  

E-Print Network [OSTI]

Electric power from offshore wind via synoptic-scale interconnection Willett Kemptona,1 , Felipe M regional estimate, Kempton et al. (2) calculated that two-thirds of the offshore wind power off the U in the U.S. Atlantic region is already underway. Fig. 1 shows as black squares offshore wind developments

Firestone, Jeremy

215

Preliminary Characterisation of Low-Temperature Bonded Copper Interconnects for 3-D Integrated Circuits  

E-Print Network [OSTI]

Three dimensional (3-D) integrated circuits can be fabricated by bonding previously processed device layers using metal-metal bonds that also serve as layer-to-layer interconnects. Bonded copper interconnects test structures ...

Leong, Hoi Liong

216

Multiparameter Moment Matching Model Reduction Approach for Generating Geometrically Parameterized Interconnect Performance Models  

E-Print Network [OSTI]

In this paper we describe an approach for generating geometrically-parameterized integrated-circuit interconnect models that are efficient enough for use in interconnect synthesis. The model generation approach presented ...

Daniel, Luca

217

Length Effects on the Reliability of Dual-Damascene Cu Interconnects  

E-Print Network [OSTI]

The effects of interconnect length on the reliability of dual-damascene Cu metallization have been investigated. As in Al-based interconnects, the lifetimes of Cu lines increase with decreasing length. However, unlike ...

Wei, F.

218

Vibration control in plates by uniformly distributed PZT actuators interconnected via electric networks  

E-Print Network [OSTI]

improve the performances of piezoelectric actuation. internal resonance / equivalent circuits 1Vibration control in plates by uniformly distributed PZT actuators interconnected via electric vibrations of plates by means of a set of electrically-interconnected piezoelectric actuators is described

Paris-Sud XI, Université de

219

H C26 Performance Analysis of Optica1 Interconnection Systems Inch-ing  

E-Print Network [OSTI]

Analysis of Optica1 Interconnection Systems Inch- ing T ransmitter T emperature Dependence .√® ¬Į √? , √? √? √¨

Choi, Woo-Young

220

Reliability of Nano-Structured Nickel Interconnections Replacing FlipChip Solder Assembly without Underfill  

E-Print Network [OSTI]

Reliability of Nano-Structured Nickel Interconnections Replacing FlipChip Solder Assembly without of Technology, GA 30332-0560 Abstract This paper reports the reliability of fine pitch interconnections using lower stresses in the interconnections and enhance reliability though they add electrical parasitics

Swaminathan, Madhavan

Note: This page contains sample records for the topic "adopted interconnection standards" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


221

Supplying Baseload Power and Reducing Transmission Requirements by Interconnecting Wind Farms  

E-Print Network [OSTI]

Supplying Baseload Power and Reducing Transmission Requirements by Interconnecting Wind Farms is not used to supply baseload electric power today. Interconnecting wind farms through the transmission grid farms are interconnected in an array, wind speed correlation among sites decreases and so does

222

Analysis of free-space optical interconnects for the three-dimensional optoelectronic stacked processor  

E-Print Network [OSTI]

Analysis of free-space optical interconnects for the three-dimensional optoelectronic stacked of free-space optical interconnect for the three-dimensional optoelectronic stacked processor (3DOESP) has VLSI; Optoelectronics; VCSELs 1. Introduction Current electronic interconnection technology cannot keep

Esener, Sadik C.

223

Optimization and Visualization of the North American Eastern Interconnect Power Market  

E-Print Network [OSTI]

Optimization and Visualization of the North American Eastern Interconnect Power Market Douglas R uses a first generation OPF model of the Eastern Interconnect to gauge the potential benefits deriving, there is sufficient low cost capacity to keep peak demand prices in the Eastern Interconnect below $50 MWH. Under

224

Ionized physical vapor deposition of integrated circuit interconnects* J. Hopwood,a)  

E-Print Network [OSTI]

Ionized physical vapor deposition of integrated circuit interconnects* J. Hopwood,a) Northeastern University, Boston, Massachusetts 02115 Received 19 November 1997; accepted 25 November 1997 Interconnects to the interconnection of semiconductor devices while the remaining 10 percent is due to transistor-related delay

225

Interconnection of nitrogen fixers and iron in the Pacific Ocean: Theory and numerical simulations  

E-Print Network [OSTI]

Interconnection of nitrogen fixers and iron in the Pacific Ocean: Theory and numerical simulations, F. Monteiro, and M. J. Follows (2012), Interconnection of nitrogen fixers and iron in the Pacific interconnected. Microbial community structure is shaped by the variable physical, chemical and predatory

226

Network Interconnection with Two-Sided User Benefits Benjamin E. Hermalin & Michael L. Katz  

E-Print Network [OSTI]

Network Interconnection with Two-Sided User Benefits Benjamin E. Hermalin & Michael L. Katz Walter Abstract Previous work on network interconnection has tended to overlook that both the sender and receiver interconnection charge is independent of the "direction" of the message and is used to induce optimal end

Sadoulet, Elisabeth

227

THE ANALYSYS OF INFORMATION IMPACTS IN COORDINATING DEFENCE AGAINST MALICIOUS ATTACKS FOR INTERCONNECTED  

E-Print Network [OSTI]

FOR INTERCONNECTED POWER SYSTEMS Ettore Bompard George Gross Roberto Napoli Fei Xue Politecnico di Torino University) in an interconnected power system to counteract such attacks has become an important problem. This paper presents to the interconnected system operators on the outcomes of the decision making process under attack. A 34-buses test

Gross, George

228

Many SIMD interconnection networks have been proposed. To put the different approaches into perspective, this analysis  

E-Print Network [OSTI]

Many SIMD interconnection networks have been proposed. To put the different approaches==Emumuuu Interconnection Netwots for SIMD Machines Howard Jay Siegel Purdue University With the advent of microprocessors our discussion to SIMD machine networks (other types are explored else- where17-19). Interconnecting N

229

The Cloud Adoption Toolkit: Supporting Cloud Adoption Decisions in the Enterprise  

E-Print Network [OSTI]

1 The Cloud Adoption Toolkit: Supporting Cloud Adoption Decisions in the Enterprise Ali Khajeh-Hosseini, David Greenwood, James W. Smith, Ian Sommerville Cloud Computing Co-laboratory, School of Computer Science University of St Andrews, UK {akh, dsg22, jws7, ifs}@cs.st-andrews.ac.uk Abstract Cloud computing

Sommerville, Ian

230

Early Adopter PDC AtEarly Adopter PDC At Washington and LeeWashington and Lee  

E-Print Network [OSTI]

Early Adopter ­ PDC AtEarly Adopter ­ PDC At Washington and LeeWashington and Lee Four-year Liberal with and manipulation of collections of stuff.manipulation of collections of stuff. · PDC applications: sorting, recursive treePDC applications: sorting, recursive tree structures, image processing,...structures, image

Stough, Joshua

231

Modeling of Customer Adoption of Distributed Energy Resources  

E-Print Network [OSTI]

Modeling of Customer Adoption of Distributed Energy Resources CALIFORNIA ENERGY COMMISSION Reliability Technology Solutions Modeling of Customer Adoption of Distributed Energy Resources Prepared the consequences. #12;#12;Modeling of Customer Adoption of Distributed Energy Resources iii Table of Contents

232

Luminous Efficacy Standards for General Purpose Lights  

Broader source: Energy.gov [DOE]

Assembly Bill 178, adopted in June 2007, established efficacy* standards for general purpose lights sold in the state of Nevada. The bill set the required efficacy at 25 lumens per watt (lm/W) of...

233

adoptive cellular immunotherapy: Topics by E-print Network  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

adoption. In order to overcome these obstacles, we propose that organizations prepare strategies and guidelines for social media adoption and use. unknown authors 217 SMEs'...

234

Taxes, Permits, and the Adoption of Abatement Technology under...  

Open Energy Info (EERE)

Taxes, Permits, and the Adoption of Abatement Technology under Imperfect Compliance Jump to: navigation, search Name Taxes, Permits, and the Adoption of Abatement Technology under...

235

Technology Adoption and Commercialization Program (New Brunswick, Canada)  

Broader source: Energy.gov [DOE]

The Technology Adoption and Commercialization Program (TAC) is intended to encourage the adoption of improved technologies and processes by offsetting some of the direct costs associated with...

236

assistance measures adopted: Topics by E-print Network  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

9 Adoption of energy-efficiency measures in SMEs An empirical analysis based on energy audit data Computer Technologies and Information Sciences Websites Summary: Adoption of...

237

Brand Standards Brand StandardsBrand Standards  

E-Print Network [OSTI]

Brand Standards 6.6.11 #12;Brand StandardsBrand Standards VISUAL IDENTITY AND BRANDING INITIATIVE, the visual image presented to the public by the units of the University and UMMC often is confusing the organizations' public image under a cohesive, easily recognized visual identity that relies upon a common

Weber, David J.

238

Environmental standards provide competitive advantage  

SciTech Connect (OSTI)

Quality organizations are breaking new ground with the development of international standards for environmental management. These promise to provide the platform for chemical companies wanting to establish their environmental credibility with a global audience. [open quotes]It will be similar to auditing our customers to ISO 9000[close quote], says the environmental manager for a European chemical firm. [open quote]We will only want to deal with people who have got their environmental act together. And we'll be in a better competitive positions[close quote]. The International Organization for Standardization (ISO;Geneva) has set up a taskforce to develop an environmental management standard, which is expected to be completed by the mid-1990s. Observers think the ISO standard will draw heavily on the British Standard Institute's (BSI;London) environmental management standard, BS7750, which will likely be the first system adopted in the world. Published last year, BS7750 has been extensively piloted in the UK (CW, Sept. 30, 1992, p. 62) and is now set to be revised before being offically adopted by BSI. The UK's Chemical Industries Association (CIA;London) is anxious to prevent a proliferation of standards, and its report on BS7750 pilot projects calls for an approach integrating quality, environment, and health and safety. But standard setters, including ISO, appear to be moving in the opposite direction. In the US, the American national Standards Institute (ANSI;Washington) has started work on an environmental management standard.

Chynoweth, E.; Kirshner, E.

1993-04-28T23:59:59.000Z

239

Laterally Interconnected Self-Organizing Maps in Hand-Written Digit Recognition  

E-Print Network [OSTI]

An application of laterally interconnected self-organizing maps (LISSOM) to handwritten digit recognition is presented. The lateral connections learn the correlations of activity between units on the map. The resulting excitatory connections focus the activity into local patches and the inhibitory connections decorrelate redundant activity on the map. The map thus forms internal representations that are easy to recognize with e.g. a perceptron network. The recognition rate on a subset of NIST database 3 is 4.0% higher with LISSOM than with a regular Self-Organizing Map (SOM) as the front end, and 15.8% higher than recognition of raw input bitmaps directly. These results form a promising starting point for building pattern recognition systems with a LISSOM map as a front end. 1 Introduction Hand-written digit recognition has become one of the touchstone problems in neural networks recently. Large databases of training examples such as the NIST (National Institute of Standards and Tech...

1996-01-01T23:59:59.000Z

240

DOE-TSPP-3, Use of Voluntary Consensus Standards and Interaction with Standards Development Organizations- August 1, 2000  

Broader source: Energy.gov [DOE]

This procedure identifies the process by which DOE adopts Voluntary Consensus Standards (VCSs) and provides guidance for the interaction of DOE and contractor employees with Standards Development Organizations (SDOs).

Note: This page contains sample records for the topic "adopted interconnection standards" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


241

Interconnecting PV on New York City's Secondary Network Distribution System  

SciTech Connect (OSTI)

The U.S. Department of Energy (DOE) has teamed with cities across the country through the Solar America Cities (SAC) partnership program to help reduce barriers and accelerate implementation of solar energy. The New York City SAC team is a partnership between the City University of New York (CUNY), the New York City Mayor s Office of Long-term Planning and Sustainability, and the New York City Economic Development Corporation (NYCEDC).The New York City SAC team is working with DOE s National Renewable Energy Laboratory (NREL) and Con Edison, the local utility, to develop a roadmap for photovoltaic (PV) installations in the five boroughs. The city set a goal to increase its installed PV capacity from1.1 MW in 2005 to 8.1 MW by 2015 (the maximum allowed in 2005). A key barrier to reaching this goal, however, is the complexity of the interconnection process with the local utility. Unique challenges are associated with connecting distributed PV systems to secondary network distribution systems (simplified to √?¬?√?¬Ę√?¬?√?¬?√?¬?√?¬?networks√?¬?√?¬Ę√?¬?√?¬?√?¬?√?¬Ě in this report). Although most areas of the country use simpler radial distribution systems to distribute electricity, larger metropolitan areas like New York City typically use networks to increase reliability in large load centers. Unlike the radial distribution system, where each customer receives power through a single line, a network uses a grid of interconnected lines to deliver power to each customer through several parallel circuits and sources. This redundancy improves reliability, but it also requires more complicated coordination and protection schemes that can be disrupted by energy exported from distributed PV systems. Currently, Con Edison studies each potential PV system in New York City to evaluate the system s impact on the network, but this is time consuming for utility engineers and may delay the customer s project or add cost for larger installations. City leaders would like to streamline this process to facilitate faster, simpler, and less expensive distributed PV system interconnections. To assess ways to improve the interconnection process, NREL conducted a four-part study with support from DOE. The NREL team then compiled the final reports from each study into this report. In Section 1√?¬?√?¬Ę√?¬?√?¬?√?¬?√?¬?PV Deployment Analysis for New York City√?¬?√?¬Ę√?¬?√?¬?√?¬?√?¬?we analyze the technical potential for rooftop PV systems in the city. This analysis evaluates potential PV power production in ten Con Edison networks of various locations and building densities (ranging from high density apartments to lower density single family homes). Next, we compare the potential power production to network loads to determine where and when PV generation is most likely to exceed network load and disrupt network protection schemes. The results of this analysis may assist Con Edison in evaluating future PV interconnection applications and in planning future network protection system upgrades. This analysis may also assist other utilities interconnecting PV systems to networks by defining a method for assessing the technical potential of PV in the network and its impact on network loads. Section 2√?¬?√?¬Ę√?¬?√?¬?√?¬?√?¬?A Briefing for Policy Makers on Connecting PV to a Network Grid√?¬?√?¬Ę√?¬?√?¬?√?¬?√?¬?presents an overview intended for nontechnical stakeholders. This section describes the issues associated with interconnecting PV systems to networks, along with possible solutions. Section 3√?¬?√?¬Ę√?¬?√?¬?√?¬?√?¬?Technical Review of Concerns and Solutions to PV Interconnection in New Y

K. Anderson; M. Coddington; K. Burman; S. Hayter; B. Kroposki; and A. Watson

2009-11-30T23:59:59.000Z

242

Spontaneous synchronization driven by energy transport in interconnected networks  

E-Print Network [OSTI]

Understanding dynamical processes on networks is an important area of research in complex systems, with far reaching implications and applications in many real-world cases. Here we introduce and study a model of intertwined dynamics on interconnected networks, inspired by the human brain, which consists of bidirectionally coupled synchronization and energy transport processes. Remarkably, the proposed model allows the emergence of spontaneous switch-like synchronization transitions driven by the energy transport dynamics, which qualitatively mirror the transitions observed in human brain dynamics between resting-state and cognitive activity. We provide a steady-state analytical explanation for the observed behavior and show that the switch-like transition is robust over a wide range of model parameters and network topologies. Finally, we suggest that the complexity inherent in other interconnected dynamical processes might be responsible for various other emergent behaviors observed in natural systems.

Vincenzo Nicosia; Per Sebastian Skardal; Vito Latora; Alex Arenas

2015-02-26T23:59:59.000Z

243

Reliability assessment of autonomous power systems incorporating HVDC interconnection links  

SciTech Connect (OSTI)

The objective of this paper is to present an improved computational method for the overall reliability assessment of autonomous power systems that may or may not contain HVdc interconnection links. This is a hybrid method based on a Monte-Carlo simulation sequential approach which incorporates an analytical approach for the reliability modeling of the HVdc transmission links. The developed models and techniques have been implemented into a computer program that can be used to simulate the operational practices and characteristics of the overall system under study efficiently and realistically. A set of reliability indices are calculated for each load-point of interest and the entire system while a set of additional indices is calculated for quantifying the reliability performance of the interconnection links under the specified operating requirements. The analysis of a practical system is also included for a number of studies representing its various operating and design characteristics.

Dialynas, E.N.; Koskolos, N.C. [National Technical Univ., Athens (Greece). Dept. of Electrical and Computer Engineering] [National Technical Univ., Athens (Greece). Dept. of Electrical and Computer Engineering; Agoris, D. [Public Power Corp., Athens (Greece)] [Public Power Corp., Athens (Greece)

1996-01-01T23:59:59.000Z

244

Series interconnected photovoltaic cells and method for making same  

DOE Patents [OSTI]

A novel photovoltaic module and method for constructing the same are disclosed. The module includes a plurality of photovoltaic cells formed on a substrate and laterally separated by interconnection regions. Each cell includes a bottom electrode, a photoactive layer and a top electrode layer. Adjacent cells are connected in electrical series by way of a conductive-buffer line. The buffer line is also useful in protecting the bottom electrode against severing during downstream layer cutting processes. 11 figs.

Albright, S.P.; Chamberlin, R.R.; Thompson, R.A.

1995-01-31T23:59:59.000Z

245

Corrosion of Metallic SOFC Interconnects in Coal Syngas  

SciTech Connect (OSTI)

With recent reductions in the operating temperature of Solid Oxide Fuel Cells (SOFC), the potential of using metallic interconnect has gone up. There is also an interest in using Coal syngas as the fuel gas and thus there is a need to analyze the behavior and performance of metallic interconnects when exposed to Coal syngas. Three high temperature material alloys, Crofer 22 APU, Ebrite and Haynes 230, having the potential to be used as SOFC interconnects were studied in simulated wet coal syngas. These alloys were exposed to syngas at 800 degrees C and for 100 hours. The exposure to coal syngas led to the formation of oxides and spinels, which evidently led to an increase in electrical resistance. Oxidation in a reducing and carburizing environment leads to unique phase and morphology formations. A comparative analysis was carried out for all the three alloys, wherein the samples were characterized by using SEM, EDS, Raman and X-Ray diffraction to obtain the morphology, thickness, composition and crystal structure of the oxides and spinels

Dastane, R.R. (University of West Virginia); Liu, X. (University of West Virginia); Johnson, C., Mao, Scott (University of Pittsburgh)

2007-09-01T23:59:59.000Z

246

Spontaneous synchronization driven by energy transport in interconnected networks  

E-Print Network [OSTI]

Understanding dynamical processes on networks is an important area of research in complex systems, with far reaching implications and applications in many real-world cases. However, the research to date has mainly focused on single dynamical processes occurring on isolated networks, and very little is known about the more interesting and realistic case of different kinds of intertwined dynamical processes taking place on interconnected networks. An example of the non-trivial combination of two types of dynamics can be found in the human brain, where cerebral circulation delivers the nutrients and oxygenated blood needed for the activity of the different brain areas, and in turn the activity of a region can induce changes in the distribution of blood flow. Here, we introduce and study a model of intertwined dynamics on interconnected networks, inspired by the human brain, which consists of bidirectionally coupled synchronization and energy transport processes. Remarkably, the proposed model allows the emergence of spontaneous switch-like synchronization transitions driven by the energy transport dynamics, which qualitatively mirror the transitions observed in human brain dynamics between resting-state and cognitive activity. We provide a steady-state analytical explanation for the observed behavior and furthermore show that the switch-like transition is robust over a wide range of model parameters and network topologies. We suggest that the complexity inherent in other interconnected dynamical processes might be responsible for various other emergent behaviors observed in natural systems.

Vincenzo Nicosia; Per Sebastian Skardal; Vito Latora; Alex Arenas

2014-07-22T23:59:59.000Z

247

2010 Texas Jurisdiction Energy Code Adoption Survey  

E-Print Network [OSTI]

populations greater than 25,000. The results for Energy Code Adoption are as follows: City Code Year Abilene 2000 Addison 2006 Allen 2006 Amarillo 2006 Angleton None Arlington 2009 Austin 2009 Baytown 2006 Beaumont 2009 Bedford 2000 Big Spring... 2006 Borger 2000 Brownsville 2006 Bryan 2003 Burleson 2006 Carrollton 2006 Cedar Hill 2006 Cedar Park 2009 Cleburne 2003 College Station 2009 Conroe 2000 Coppell 2006 Copperas Cove 2000 Corpus Christi 2003 Corsicana 2009 Dallas 2006...

248

Market Transformation: Fuel Cell Early Adoption (Presentation...  

Office of Environmental Management (EM)

Fuel Cell Technologies Office Hydrogen Production Hydrogen Delivery Hydrogen Storage Fuel Cells Technology Validation Manufacturing Safety, Codes, and Standards Education Market...

249

The Treatment of Renewable Energy Certificates, Emissions Allowances, and Green Power Programs in State Renewables Portfolio Standards  

E-Print Network [OSTI]

Green Power Programs in State Renewables Portfolio StandardsGreen Power Programs in State Renewables Portfolio Standardshave adopted mandatory renewables portfolio standards (RPS)

Holt, Edward A.; Wiser, Ryan H.

2007-01-01T23:59:59.000Z

250

Technology adoption: who is likely to adopt and how does the timing affect the benefits?  

E-Print Network [OSTI]

Many fields of economics point to technology as the primary vehicle for change. Agencies pushing change often promote technology adoption to achieve their goals. To improve our understanding of how efforts to push new technologies should...

Rubas, Debra Joyce

2004-11-15T23:59:59.000Z

251

First time adoption of IFRS, Fair value option, Conservatism: Evidences from French listed companies  

E-Print Network [OSTI]

companies Samira DEMARIA and Dominique DUFOUR Abstract: The European Commission set 2005 as the date for the move to IFRS for all companies listed on European stock exchanges. The paper studies the first adoption accounting options made by French companies during the transition to IFRS standards? The paper is organized

Paris-Sud XI, Université de

252

ORDINANCE NO. XXXX AN ORDINANCE ADOPTING THE 2010 CALIFORNIA GREEN BUILDING  

E-Print Network [OSTI]

1 ORDINANCE NO. XXXX AN ORDINANCE ADOPTING THE 2010 CALIFORNIA GREEN BUILDING STANDARDS CODE, AND ADDING SECTION 15.04.125 AS "SAN CARLOS GREEN BUILDING ORDINANCE" The City Council of the City of San, through the 2030 General Plan, within the City of San Carlos to address climate change

253

High Penetration, Grid Connected Photovoltaic Technology Codes and Standards: Preprint  

SciTech Connect (OSTI)

This paper reports the interim status in identifying and reviewing photovoltaic (PV) codes and standards (C&S) and related electrical activities for grid-connected, high-penetration PV systems with a focus on U.S. electric utility distribution grid interconnection.

Basso, T. S.

2008-05-01T23:59:59.000Z

254

[ HIGH PERFORMANCE BUILDING STANDARD] STATE OF MONTANA HIGH PERFORMANCE BUILDING STANDARDS  

E-Print Network [OSTI]

[ HIGH PERFORMANCE BUILDING STANDARD] PART 2 HPBS STATE OF MONTANA HIGH PERFORMANCE BUILDING. These High Performance Building Standards are promulgated to implement the directives established in SB 49 which amended Section 17-7-201, MCA. B. These High Performance Building Standards were adopted on June 1

Dyer, Bill

255

U.S. Virgin Islands Establishes Interconnection Standards to Clear the Way  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious Rank EERE: AlternativeEnvironment,Institutes and1TeleworkAgriculture U.S. DepartmentofDepartment of|for Grid

256

Monolithically interconnected GaAs solar cells: A new interconnection technology for high voltage solar cell output  

SciTech Connect (OSTI)

Photovoltaic linear concentrator arrays can benefit from high performance solar cell technologies being developed at AstroPower. Specifically, these are the integration of thin GaAs solar cell and epitaxial lateral overgrowth technologies with the application of monolithically interconnected solar cell (MISC) techniques. This MISC array has several advantages which make it ideal for space concentrator systems. These are high system voltage, reliable low cost monolithically formed interconnections, design flexibility, costs that are independent of array voltage, and low power loss from shorts, opens, and impact damage. This concentrator solar cell will incorporate the benefits of light trapping by growing the device active layers over a low-cost, simple, PECVD deposited silicon/silicon dioxide Bragg reflector. The high voltage-low current output results in minimal 12R losses while properly designing the device allows for minimal shading and resistance losses. It is possible to obtain open circuit voltages as high as 67 volts/cm of solar cell length with existing technology. The projected power density for the high performance device is 5 kW/m for an AMO efficiency of 26% at 1 5X. Concentrator solar cell arrays are necessary to meet the power requirements of specific mission platforms and can supply high voltage power for electric propulsion systems. It is anticipated that the high efficiency, GaAs monolithically interconnected linear concentrator solar cell array will enjoy widespread application for space based solar power needs. Additional applications include remote man-portable or ultra-light unmanned air vehicle (UAV) power supplies where high power per area, high radiation hardness and a high bus voltage or low bus current are important. The monolithic approach has a number of inherent advantages, including reduced cost per interconnect and increased reliability of array connections. There is also a high potential for a large number of consumer products.

Dinetta, L.C.; Hannon, M.H.

1995-10-01T23:59:59.000Z

257

Effects of a carbon tax on microgrid combined heat and power adoption  

SciTech Connect (OSTI)

This paper describes the economically optimal adoption and operation of distributed energy resources (DER) by a hypothetical California microgrid consisting of a group of commercial buildings over an historic test year, 1999. The optimization is conducted using a customer adoption model (DER-CAM) developed at Berkeley Lab and implemented in the General Algebraic Modeling System (GAMS). A microgrid is a semiautonomous grouping of electricity and heat loads interconnected to the existing utility grid (macrogrid) but able to island from it. The microgrid minimizes the cost of meeting its energy requirements (consisting of both electricity and heat loads) by optimizing the installation and operation of DER technologies while purchasing residual energy from the local combined natural gas and electricity utility. The available DER technologies are small-scale generators (< 500 kW), such as reciprocating engines, microturbines, and fuel cells, with or without combined heat and power (CHP) equipment, such as water and space heating and/or absorption cooling. By introducing a tax on carbon emissions, it is shown that if the microgrid is allowed to install CHP-enabled DER technologies, its carbon emissions are mitigated more than without CHP, demonstrating the potential benefits of small-scale CHP technology for climate change mitigation. Reciprocating engines with heat recovery and/or absorption cooling tend to be attractive technologies for the mild southern California climate, but the carbon mitigation tends to be modest compared to purchasing utility electricity because of the predominance of relatively clean central station generation in California.

Siddiqui, Afzal S.; Marnay, Chris; Edwards, Jennifer L.; Firestone, Ryan M.; Ghosh, Srijay; Stadler, Michael

2004-11-01T23:59:59.000Z

258

Pesticide safety risk, food chain organization, and the adoption of sustainable farming practices. The case of Moroccan early tomatoes  

E-Print Network [OSTI]

1 Pesticide safety risk, food chain organization, and the adoption of sustainable farming practices standards and more recently process standards (Good agricultural practices and integrated pest management. The case of Moroccan early tomatoes Magali Aubert1 , Zouhair Bouhsina1 , Jean-Marie Codron1 , Sylvain

Paris-Sud XI, Université de

259

Estimation of the Energy and Capacity Savings in Texas from Appliance Efficiency Standards  

E-Print Network [OSTI]

The purpose of this presentation will be to assess the technical potential for energy and capacity savings in Texas by the year 2006 by the statewide adoption of minimum appliance efficiency standards equivalent to those recently adopted...

Verdict, M.

1986-01-01T23:59:59.000Z

260

Final Report on Transmission Pricing in the Western Interconnection  

SciTech Connect (OSTI)

Under this project, the Committee on Regional Electric Power Cooperation (CREPC) of the Western Interstate Energy Board developed a ''western pricing and congestion management proposal'' in order to foster efficient wholesale power markets and efficient use and expansion of the transmission grid. Drafts of this paper provided useful information to states/provinces in the Western Interconnection as Western Regional Transmission Organization (RTO) transmission pricing proposals have continued to evolve. Throughout the project there has been a gradual, but incomplete agreement on pricing systems to be used by RTOs in the West.

Douglas C. Larson; Lawrence Nordell

2003-06-25T23:59:59.000Z

Note: This page contains sample records for the topic "adopted interconnection standards" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


261

Novel Composite Materials for SOFC Cathode-Interconnect Contact  

SciTech Connect (OSTI)

This report summarized the research efforts and major conclusions of our University Coal Research Project, which focused on developing a new class of electrically-conductive, Cr-blocking, damage-tolerant Ag-perovksite composite materials for the cathode-interconnect contact of intermediate-temperature solid oxide fuel cell (SOFC) stacks. The Ag evaporation rate increased linearly with air flow rate initially and became constant for the air flow rate {ge} {approx} 1.0 cm {center_dot} s{sup -1}. An activation energy of 280 KJ.mol{sup -1} was obtained for Ag evaporation in both air and Ar+5%H{sub 2}+3%H{sub 2}O. The exposure environment had no measurable influence on the Ag evaporation rate as well as its dependence on the gas flow rate, while different surface morphological features were developed after thermal exposure in the oxidizing and reducing environments. Pure Ag is too volatile at the SOFC operating temperature and its evaporation rate needs to be reduced to facilitate its application as the cathode-interconnect contact. Based on extensive evaporation testing, it was found that none of the alloying additions reduced the evaporation rate of Ag over the long-term exposure, except the noble metals Au, Pt, and Pd; however, these noble elements are too expensive to justify their practical use in contact materials. Furthermore, the addition of La{sub 0.8}Sr{sub 0.2}MnO{sub 3} (LSM) into Ag to form a composite material also did not significantly modify the Ag evaporation rate. The Ag-perovskite composites with the perovskite being either (La{sub 0.6}Sr{sub 0.4})(Co{sub 0.8}Fe{sub 0.2})O{sub 3} (LSCF) or LSM were systematically evaluated as the contact material between the ferritic interconnect alloy Crofer 22 APU and the LSM cathode. The area specific resistances (ASRs) of the test specimens were shown to be highly dependent on the volume percentage and the type of the perovskite present in the composite contact material as well as the amount of thermal cycling that the specimens were subjected to during testing. The Ag-LSCF composite contact materials proved more effective in trapping Cr within the contact material and preventing Cr migration into the cathode than the Ag-LSM composites. Ag-perovskite composite contact materials are promising candidates for use in intermediate-temperature SOFC stacks with ferritic stainless steel interconnects due to their ability to maintain acceptably low ASRs while reducing Cr migration into the cathode material.

J. H. Zhu

2009-07-31T23:59:59.000Z

262

Series interconnected photovoltaic cells and method for making same  

DOE Patents [OSTI]

A novel photovoltaic module (10) and method for constructing the same are disclosed. The module (10) includes a plurality of photovoltaic cells (12) formed on a substrate (14) and laterally separated by interconnection regions (15). Each cell (12) includes a bottom electrode (16), a photoactive layer (18) and a top electrode layer (20). Adjacent cells (12) are connected in electrical series by way of a conductive-buffer line (22). The buffer line (22) is also useful in protecting the bottom electrode (16) against severing during downstream layer cutting processes.

Albright, Scot P. (El Paso, TX); Chamberlin, Rhodes R. (El Paso, TX); Thompson, Roger A. (Littleton, CO)

1995-01-01T23:59:59.000Z

263

Evaluation of a Functional Interconnect System for SOFC's  

SciTech Connect (OSTI)

The overall objective of this project was to validate the concept and application of a functional interconnect, based on a ferritic stainless steel, for a solid oxide fuel cell through manufacturing trials, laboratory testing, and field experience. The materials of construction and their surfaces were to be optimized for the particular service conditions and include low-cost ferritic stainless steels, novel postprocess treatments, and third-party coatings. This work aimed to optimize specific aspects of substrate alloy chemistry and to study the effects of long-term exposures on resistive oxide film structure and chemistry, interaction with applied surface coatings, and effectiveness of novel surface treatments.

Matthew Bender; James Rakowski

2010-12-31T23:59:59.000Z

264

Western Interconnection Energy Imbalance Market Status and Prospects (Presentation)  

SciTech Connect (OSTI)

This presentation describes how a new wholesale electricity market for energy imbalance ancillary services could be implemented and operated. Some conclusions of this presentation are: (1) Method for calculating additional reserve requirements due to wind and solar production; (2) EIM results in substantial reduction in reserves requirements and ramping demand; (3) Reduced participation reduces benefits for all but reduces the benefits to non-participants the most; (4) Full participation leads to maximum benefit across the Western Interconnection, up to 42% of total reserve requirement; and (5) Regional EIM implementations have smaller but substantial benefits.

Milligan, M.; Kirby, B.; King, J.; Beuning, S.

2011-10-01T23:59:59.000Z

265

National Electric Transmission Study 2006 Western Interconnection Analysis  

Office of Environmental Management (EM)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May Jun Jul(Summary) "of EnergyEnergyENERGY TAXBalanced Scorecard Federal2 to:DieselEnergy AuditorWestern Interconnection 2006

266

A New Algorithm for Standard Cell Global Routing Department of Computer Science  

E-Print Network [OSTI]

% reduction in the total channel density compared to the Timberwolf 4.2 package. Keywords: Global routingA New Algorithm for Standard Cell Global Routing Jason Cong Department of Computer Science for standard cell global routing. The algorithm considers all of the interconnection nets simultaneously

Cong, Jason "Jingsheng"

267

WECC releases its first-ever transmission plan for the Western Interconnection  

Broader source: Energy.gov [DOE]

The Western Electricity Coordinating Council (WECC) announced the release of its first 10-Year Regional Transmission Plan (Plan) for the Western Interconnection.

268

Interconnection of Direct-drive Wind Turbines Using A Series Connected DC Grid.  

E-Print Network [OSTI]

??This thesis presents the concept of a "distributed HVDC converter" for offshore wind farms. The proposed converter topology allows series interconnection of wind turbines obviatingÖ (more)

Veilleux, Etienne

2010-01-01T23:59:59.000Z

269

Comparing Germany's and California's Interconnection Processes for PV Systems (White Paper)  

SciTech Connect (OSTI)

Establishing interconnection to the grid is a recognized barrier to the deployment of distributed energy generation. This report compares interconnection processes for photovoltaic projects in California and Germany. This report summarizes the steps of the interconnection process for developers and utilities, the average length of time utilities take to process applications, and paperwork required of project developers. Based on a review of the available literature, this report finds that while the interconnection procedures and timelines are similar in California and Germany, differences in the legal and regulatory frameworks are substantial.

Tweedie, A.; Doris, E.

2011-07-01T23:59:59.000Z

270

Alaska Gateway School District Adopts Combined Heat and Power...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Alaska Gateway School District Adopts Combined Heat and Power Alaska Gateway School District Adopts Combined Heat and Power May 7, 2013 - 12:00am Addthis In Tok, Alaska, the...

271

Solar Adoption and Energy Consumption in the Residential Sector  

E-Print Network [OSTI]

solar systems and energy efficiency and conservationEnergy Tax Act encouraged homeowners to invest in energy conservation and solarenergy consumption patterns: that some adopters of solar will thereafter become adopters of energy conservation

McAllister, Joseph Andrew

2012-01-01T23:59:59.000Z

272

adopting g4 dna: Topics by E-print Network  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

children from foster care to adoptive families. unknown authors 25 Adoption of New Technology CiteSeer Summary: The contribution of new technology to economic growth can only be...

273

adoptive immunotherapy requirement: Topics by E-print Network  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

children from foster care to adoptive families. unknown authors 20 Adoption of New Technology CiteSeer Summary: The contribution of new technology to economic growth can only be...

274

Cloud computing adoption model for governments and large enterprises  

E-Print Network [OSTI]

Cloud Computing has held organizations across the globe spell bound with its promise. As it moves from being a buzz word and hype into adoption, organizations are faced with question of how to best adopt cloud. Existing ...

Trivedi, Hrishikesh

2013-01-01T23:59:59.000Z

275

Electrical isolation of component cells in monolithically interconnected modules  

DOE Patents [OSTI]

A monolithically interconnected photovoltaic module having cells which are electrically connected which comprises a substrate, a plurality of cells formed over the substrate, each cell including a primary absorber layer having a light receiving surface and a p-region, formed with a p-type dopant, and an n-region formed with an n-type dopant adjacent the p-region to form a single pn-junction, and a cell isolation diode layer having a p-region, formed with a p-type dopant, and an n-region formed with an n-type dopant adjacent the p-region to form a single pn-junction, the diode layer intervening the substrate and the absorber layer wherein the absorber and diode interfacial regions of a same conductivity type orientation, the diode layer having a reverse-breakdown voltage sufficient to prevent inter-cell shunting, and each cell electrically isolated from adjacent cells with a vertical trench trough the pn-junction of the diode layer, interconnects disposed in the trenches contacting the absorber regions of adjacent cells which are doped an opposite conductivity type, and electrical contacts.

Wanlass, Mark W. (Golden, CO)

2001-01-01T23:59:59.000Z

276

On Irregular Interconnect Fabrics for Self-Assembled Nanoscale Electronics  

E-Print Network [OSTI]

Nanoscale electronics and novel fabrication technologies bear unique opportunities for self-assembling multi-billion component systems in a largely random manner, which would likely lower fabrication costs significantly compared to a definite ad hoc assembly. It has been shown that communication networks with the small-world property have major advantages in terms of transport characteristics and robustness over regularly connected systems. In this paper we pragmatically investigate the properties of an irregular, abstract, yet physically plausible small-world interconnect fabric that is inspired by modern network-on-chip paradigms. We vary the framework's key parameters, such as the connectivity, the number of switch blocks, the number of virtual channels, the routing strategy, the distribution of long- and short-range connections, and measure the network's transport characteristics and robustness against failures. We further explore the ability and efficiency to solve two simple toy problems, the synchronization and the density classification task. The results confirm that (1) computation in irregular assemblies is a promising new computing paradigm for nanoscale electronics and (2) that small-world interconnect fabrics have major advantages over local CA-like topologies. Finally, the results will help to make important design decisions for building self-assembled electronics in a largely random manner.

Christof Teuscher

2006-06-22T23:59:59.000Z

277

1.800.ASK.DTFA www.DaveThomasFoundationForAdoption.org Dave Thomas Foundation for Adoption  

E-Print Network [OSTI]

as victims of child abuse, neglect or abandonment. More than 129,000 children in foster care are available Care Adoption Awareness FACT SHEET THE CAUSE: November is National Adoption Awareness Month. It has in America's foster care system who are available for adoption and wait for permanent families. THE NEED

Jones, Michelle

278

Extraction and Modeling of the Optoelectronic Characteristics of an Optical Interconnect Link  

E-Print Network [OSTI]

Extraction and Modeling of the Optoelectronic Characteristics of an Optical Interconnect Link a technique that enables the extraction and modeling of some of the channel's optoelectronic characteristics and optoelectronic com- ponents utilized in the link. 1. Introduction In the last decade optical interconnects have

Esener, Sadik C.

279

Predictions, Challenges, and Opportunities in CMOS Compatible On-Chip Optical Interconnect  

E-Print Network [OSTI]

to a few picoseconds. IV. ELECTRICAL VS. OPTICAL INTERCONNECTS Different criteria used in the design of the . Friedman Department of Electrical and Computer Engineering University of Rochester, Rochester, New York for electrical interconnect. Predictions of the performance of CMOS compatible optical devices are made based

Friedman, Eby G.

280

Plasticity contributions to interface adhesion in thin-film interconnect structures  

E-Print Network [OSTI]

Plasticity contributions to interface adhesion in thin-film interconnect structures Michael Lanea of plasticity in thin copper layers on the interface fracture resistance in thin-film interconnect structures yield properties together with a plastic flow model for the metal layers were used to predict

Vainchtein, Anna

Note: This page contains sample records for the topic "adopted interconnection standards" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


281

Power Reduction of CMP Communication Networks via RF-Interconnects M-C. Frank Chang  

E-Print Network [OSTI]

- alized via integration of Radio Frequency Interconnect (RF- I) through on-chip transmission lines of analog waves over on- chip transmission lines. These technologies include radio fre- quency interconnect latency and low energy consumption [5][7]. RF-I transmission lines provide single-cycle cross

Cong, Jason "Jingsheng"

282

Control Design for Interconnected Power Systems with OLTCs via Robust Decentralized Control  

E-Print Network [OSTI]

Control Design for Interconnected Power Systems with OLTCs via Robust Decentralized Control the problem of designing a decentralized control of interconnected power systems, with OLTC and SVCs, under-scale Markov jump parameter systems framework. In this paper, unlike other control schemes, OLTC transformers

Pota, Himanshu Roy

283

Home Energy Displays: Consumer Adoption and Response  

SciTech Connect (OSTI)

The focus of this project was to investigate the factors influencing consumer adoption of Home Energy Displays (HEDs) and to evaluate electricity consumption in households with basic HEDs versus enhanced feedback methods - web portals or alerts. We hypothesized that providing flexible and relatable information to users, in addition to a basic HED, would make feedback more effective and achieve persistent energy savings. In Phase I, we conducted three user research studies and found preferences for aesthetically pleasing, easy to understand feedback that is accessible through multiple media and offered free of charge. The deployment of HEDs in 150 households planned for Phase II encountered major recruitment and HED field deployment problems. First, after extensive outreach campaigns to apartment complexes with 760 units, only 8% of building's tenants elected to receive a free HED in their homes as part of the field study. Second, the HED used, a leading market model, had a spectrum of problems, including gateway miscommunications, failure to post to a data-hosting third party, and display malfunctions. In light of these challenges, we are pursuing a modified study investigating the energy savings of a web portal versus alert-based energy feedback instead of a physical HED.

LaMarche, J.; Cheney, K.; Akers, C.; Roth, K.; Sachs, O.

2012-12-01T23:59:59.000Z

284

National Agenda for Hydrogen Codes and Standards  

SciTech Connect (OSTI)

This paper provides an overview of hydrogen codes and standards with an emphasis on the national effort supported and managed by the U.S. Department of Energy (DOE). With the help and cooperation of standards and model code development organizations, industry, and other interested parties, DOE has established a coordinated national agenda for hydrogen and fuel cell codes and standards. With the adoption of the Research, Development, and Demonstration Roadmap and with its implementation through the Codes and Standards Technical Team, DOE helps strengthen the scientific basis for requirements incorporated in codes and standards that, in turn, will facilitate international market receptivity for hydrogen and fuel cell technologies.

Blake, C.

2010-05-01T23:59:59.000Z

285

Catalytic bipolar interconnection plate for use in a fuel cell  

DOE Patents [OSTI]

A bipolar interconnection plate for use between adjacent fuel cell units in a stacked fuel cell assembly. Each plate is manufactured from an intermetallic composition, examples of which include NiAl or Ni.sub.3 Al which can catalyze steam reforming of hydrocarbons. Distributed within the intermetallic structure of the plate is a ceramic filler composition. The plate includes a first side with gas flow channels therein and a second side with fuel flow channels therein. A protective coating is applied to the first side, with exemplary coatings including strontium-doped or calcium-doped lanthanum chromite. To produce the plate, Ni and Al powders are combined with the filler composition, compressed at a pressure of about 10,000-30,000 psi, and heated to about 600.degree.-1000.degree. C. The coating is then applied to the first side of the completed plate using liquid injection plasma deposition or other deposition techniques.

Lessing, Paul A. (Idaho Falls, ID)

1996-01-01T23:59:59.000Z

286

Catalytic bipolar interconnection plate for use in a fuel cell  

DOE Patents [OSTI]

A bipolar interconnection plate is described for use between adjacent fuel cell units in a stacked fuel cell assembly. Each plate is manufactured from an intermetallic composition, examples of which include NiAl or Ni{sub 3}Al which can catalyze steam reforming of hydrocarbons. Distributed within the intermetallic structure of the plate is a ceramic filler composition. The plate includes a first side with gas flow channels therein and a second side with fuel flow channels therein. A protective coating is applied to the first side, with exemplary coatings including strontium-doped or calcium-doped lanthanum chromite. To produce the plate, Ni and Al powders are combined with the filler composition, compressed at a pressure of about 10,000--30,000 psi, and heated to about 600--1000 C. The coating is then applied to the first side of the completed plate using liquid injection plasma deposition or other deposition techniques. 6 figs.

Lessing, P.A.

1996-03-05T23:59:59.000Z

287

Geothermal Power and Interconnection: The Economics of Getting to Market  

SciTech Connect (OSTI)

This report provides a baseline description of the transmission issues affecting geothermal technologies. The report begins with a comprehensive overview of the grid, how it is planned, how it is used, and how it is paid for. The report then overlays onto this 'big picture' three types of geothermal technologies: conventional hydrothermal systems; emerging technologies such as enhanced engineered geothermal systems (EGS) and geopressured geothermal; and geothermal co-production with existing oil and gas wells. Each category of geothermal technology has its own set of interconnection issues, and these are examined separately for each. The report draws conclusions about each technology's market affinities as defined by factors related to transmission and distribution infrastructure. It finishes with an assessment of selected markets with known geothermal potential, identifying those that offer the best prospects for near-term commercial development and for demonstration projects.

Hurlbut, D.

2012-04-01T23:59:59.000Z

288

Efficient algorithm to compute mutually connected components in interconnected networks  

E-Print Network [OSTI]

Mutually connected components (MCCs) play an important role as a measure of resilience in the study of interconnected networks. Despite their importance, an efficient algorithm to obtain physical properties of all MCCs during the removals of links is not available. Here, using a well-known fully-dynamic graph algorithm, we propose an efficient algorithm to accomplish this. We show that the time complexity of this algorithm is approximately $\\mathcal{O}(N^{1.2})$, which is more efficient than the brute-force algorithm with complexity $\\mathcal{O}(N^{2})$. We anticipate this algorithm to allow simulations with complex dynamic rules to research a size regime that was not permitted before.

Hwang, S; Lee, Deokjae; Kahng, B

2014-01-01T23:59:59.000Z

289

Polarimetric Standardization  

E-Print Network [OSTI]

The use of polarimetric techniques is nowadays widespread among solar and stellar astronomers. However, notwithstanding the recommandations that have often been made about the publication of polarimetric results in the astronomical literature, we are still far from having a standard protocol on which to conform. In this paper we review the basic definitions and the physical significance of the Stokes parameters, and we propose a standardization of the measurement of polarized radiation.

E. Landi Degl'Innocenti; S. Bagnulo; L. Fossati

2006-10-09T23:59:59.000Z

290

Abstract--It is impractical to analyze all of the possible contingencies in a large-scale interconnected power network.  

E-Print Network [OSTI]

University. He joined PJM Interconnection as a transmission planning engineer recently. (e-mail: chenq@pjm

McCalley, James D.

291

Seasonal Movements and Spatial Distributions of Common Carp in an Interconnected Glacial Lake System in Eastern South Dakota  

E-Print Network [OSTI]

0 Seasonal Movements and Spatial Distributions of Common Carp in an Interconnected Glacial Lake in an Interconnected Glacial Lake System in Eastern South Dakota This thesis is approved as a creditable Distributions of Common Carp in an Interconnected Glacial Lake System in Eastern South Dakota Matthew J.

292

p r o g r e s s r e p o r t s Interconnect: A Fundamental Constraint  

E-Print Network [OSTI]

p r o g r e s s r e p o r t s Interconnect: A Fundamental Constraint André DeHon e n g e n i o u devices. This shows up most clearly when we need to interconnect physically distinct computa- tional to implement some larger computation or compu- tational structure. The interconnect which links these elements

Haile, Sossina M.

293

Effects of a carbon tax on combined heat and power adoption by a microgrid  

SciTech Connect (OSTI)

This paper describes the economically optimal adoption and operation of distributed energy resources (DER) by a hypothetical California microgrid ((mu)Grid) consisting of a group of commercial buildings over an historic test year, 1999. The optimization is conducted using a customer adoption model (DER-CAM) developed at Berkeley Lab and implemented in the General Algebraic Modeling System (GAMS). A (mu)Grid is a semiautonomous grouping of electricity and heat loads interconnected to the existing utility grid (macrogrid) but able to island from it. The (mu)Grid minimizes the cost of meeting its energy requirements (consisting of both electricity and heat loads) by optimizing the installation and operation of DER technologies while purchasing residual energy from the local combined natural gas and electricity utility. The available DER technologies are small-scale generators (< 500 kW), such as reciprocating engines, microturbines, and fuel cells, with or without CHP equipment, such as water- and space-heating and/or absorption cooling. By introducing a tax on carbon emissions, it is shown that if the (mu)Grid is allowed to install CHP-enabled DER technologies, its carbon emissions are mitigated more than without CHP, demonstrating the potential benefits of small-scale CHP technology for climate change mitigation. Reciprocating engines with heat recovery and/or absorption cooling tend to be attractive technologies for the mild southern California climate, but the carbon mitigation tends to be modest compared to purchasing utility electricity because of the predominance of relatively clean generation in California.

Marnay, Chris; Edwards, Jennifer L.; Firestone, Ryan M.; Ghosh, Srijay; Siddidqui, Afzal S.; Stadler, Michael

2002-10-01T23:59:59.000Z

294

Solar Adoption and Energy Consumption in the Residential Sector.  

E-Print Network [OSTI]

??This dissertation analyzes the energy consumption behavior of residential adopters of solar photovoltaic systems (solar-PV). Based on large data sets from the San Diego regionÖ (more)

McAllister, Joseph Andrew

2012-01-01T23:59:59.000Z

295

Top Management Involvement in the Adoption of Energy Efficiency Projects  

E-Print Network [OSTI]

Adoption: The Case of Energy- Efficiency Audits. Resource695. Expert Group on Energy Efficiency. 2007. Realizing theDiscount Rates and Energy Efficiency. Contemporary Economic

Blass, Vered; Corbett, Charles J.; Delmas, Magali A; Muthulingam, Suresh

2011-01-01T23:59:59.000Z

296

California Member Connects Solar Adoption With Upgrades | Department...  

Broader source: Energy.gov (indexed) [DOE]

Photo of a young man working on solar panels. Studies on the connection between solar adoption and energy upgrades by Better Buildings Residential Network member Center for...

297

Adopting LED Technology: What Federal Facility Managers Need to Know  

Broader source: Energy.gov [DOE]

This document describes the presentation slides for the "Adopting LED Technology: What Federal Facility Managers Need to Know" webinar that took place on September 11, 2014.

298

Geothermal Heat Pumps: Market Status, Barriers to Adoption, and...  

Open Energy Info (EERE)

Barriers to Adoption, and Actions to Overcome Barriers AgencyCompany Organization: Oak Ridge National Laboratory Sector: Energy Focus Area: Renewable Energy, Geothermal...

299

Solar Adoption and Energy Consumption in the Residential Sector  

E-Print Network [OSTI]

Process in the Adoption of Solar Energy Systems." Journal ofthe diffusion of innovation: Solar energy technology in Sri2010. Washington, DC, Solar Energy Industries Association:

McAllister, Joseph Andrew

2012-01-01T23:59:59.000Z

300

City of Phoenix- Design Standards for City Buildings  

Broader source: Energy.gov [DOE]

The City of Phoenix has had energy standards for public buildings in place since 2005. In June 2005, the Phoenix City Council adopted a policy requiring all new city buildings built with 2006 bond...

Note: This page contains sample records for the topic "adopted interconnection standards" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


301

City of Asheville- Efficiency Standards for City Buildings  

Broader source: Energy.gov [DOE]

In April 2007, the Asheville City Council adopted carbon emission reduction goals and set LEED standards for new city buildings. The council committed to reducing carbon emissions by 2% per year...

302

City of Plano- LEED Standard for Public Buildings  

Broader source: Energy.gov [DOE]

As of January 2007, the City of Plano adopted a policy to "finance, plan, design, construct, manage, renovate, and maintain its facilities and buildings to be sustainable." This standard applies...

303

Application for Locally Adopted Energy Standards by the City of Oakland in Accordance With  

E-Print Network [OSTI]

BUILDING REQUIREMENTS FOR PRIVATE DEVELOPMENT TO ESTABLISH ENVIRONMENTALLY SUSTAINABLE REGULATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Appendix: Alameda County Small Commercial Green Building Checklist #12;Application for Oakland the introduction of its Green Building Ordinance on July 6, 2010. The new ordinance is scheduled to take effect

304

Application for Locally Adopted Energy Standards by the City of Morgan Hill  

E-Print Network [OSTI]

of the U. S. Green Building Council LEED rating system for nonresidential buildings and the Build It Green ................................................................................................... 13 2.3 Lowrise Residential Building .............................................................................................. 15 2.4 HighRise Residential Building

305

Accelerating the Adoption of Second-Tier Reach Standards for Applicable Appliance Products in China  

E-Print Network [OSTI]

of funding such as demand-side-management (DSM) programsutility-based demand-side management (DSM) program. Consumerdeveloped economies, demand-side-management (DSM) programs

Lin, Jiang; Fridley, David

2008-01-01T23:59:59.000Z

306

Sustainability in the product cycle : adopting a shared standard for the apparel industry  

E-Print Network [OSTI]

Decisions made by product designers strongly influence the social and environmental impacts that a consumer product will have over its lifetime. This study examines the Sustainable Apparel Index, a decision-support tool ...

Hartley, Alice C. (Alice Catherine)

2012-01-01T23:59:59.000Z

307

Grid Interconnection and Performance Testing Procedures for Vehicle-To-Grid (V2G) Power Electronics: Preprint  

SciTech Connect (OSTI)

Bidirectional power electronics can add vehicle-to-grid (V2G) capability in a plug-in vehicle, which then allows the vehicle to operate as a distributed resource (DR). The uniqueness of the battery-based V2G power electronics requires a test procedure that will not only maintain IEEE interconnection standards, but can also evaluate the electrical performance of the vehicle working as a DR. The objective of this paper is to discuss a recently published NREL technical report that provides interim test procedures for V2G vehicles for their integration into the electrical distribution systems and for their performance in terms of continuous output power, efficiency, and losses. Additionally, some other test procedures are discussed that are applicable to a V2G vehicle that desires to provide power reserve functions. A few sample test results are provided based on testing of prototype V2G vehicles at NREL.

Kramer, W.; Chakraborty, S.; Kroposki, B.; Hoke, A.; Martin, G.; Markel, T.

2012-03-01T23:59:59.000Z

308

Solid oxide fuel cell with internal reforming, catalyzed interconnect for use therewith, and methods  

DOE Patents [OSTI]

A catalyzed interconnect for an SOFC electrically connects an anode and an anodic current collector and comprises a metallic substrate, which provides space between the anode and anodic current collector for fuel gas flow over at least a portion of the anode, and a catalytic coating on the metallic substrate comprising a catalyst for catalyzing hydrocarbon fuel in the fuel gas to hydrogen rich reformate. An SOFC including the catalyzed anodic inter-connect, a method for operating an SOFC, and a method for making a catalyzed anodic interconnect are also disclosed.

Liu, Di-Jia; Guan, Jie; Minh, Nguyen

2010-06-08T23:59:59.000Z

309

Economic and Environmental Impacts of Adoption of Genetically Modified Rice in California  

E-Print Network [OSTI]

growers. Economic and Environmental Impacts of Adoption of43Ė50. Economic and Environmental Impacts of Adoption ofEconomic and Environmental Impacts of Adoption of

Bond, Craig A.; Carter, C A; Farzin, Y. Hossein

2005-01-01T23:59:59.000Z

310

Influence of Regional Development Policies and Clean Technology Adoption on Future Air Pollution Exposure  

E-Print Network [OSTI]

development policies and clean technology adoption on futuredevelopment policies and clean technology adoption on futuredevelopment policies and clean technology adoption on future

2010-01-01T23:59:59.000Z

311

Michigan State Code Adoption Analysis: Cost-Effectiveness of Lighting Requirements - ASHRAE/IESNA 90.1-2004  

SciTech Connect (OSTI)

This report documents PNNL's analysis of the potential energy effect and cost-effectiveness of the lighting requirements in ASHRAE/IESNA 90.1-2004 if this energy code is adopted in the state of Michigan, instead of the current standard.

Richman, Eric E.

2006-09-29T23:59:59.000Z

312

Nuclear-renewable hybrid energy systems: Opportunities, interconnections, and needs  

SciTech Connect (OSTI)

As the U.S. energy system evolves, the amount of electricity from variable-generation sources is likely to increase, which could result in additional times when electricity demand is lower than available production. Thus, purveyors of technologies that traditionally have provided base-load electricityósuch as nuclear power plantsócan explore new operating procedures to deal with the associated market signals. Concurrently, innovations in nuclear reactor design coupled with sophisticated control systems now allow for more complex apportionment of heat within an integrated system such as one linked to energy-intensive chemical processes. This paper explores one opportunity Ė nuclear-renewable hybrid energy systems. These are defined as integrated facilities comprised of nuclear reactors, renewable energy generation, and industrial processes that can simultaneously address the need for grid flexibility, greenhouse gas emission reductions, and optimal use of investment capital. Six aspects of interaction (interconnections) between elements of nuclear-renewable hybrid energy systems are identified: Thermal, electrical, chemical, hydrogen, mechanical, and information. Additionally, system-level aspects affect selection, design, and operation of this hybrid system type. Throughout the paper, gaps and research needs are identified to promote further exploration of the topic.

Mark F. Ruth; Owen R. Zinaman; Mark Antkowiak; Richard D. Boardman; Robert S. Cherry; Morgan D. Bazilian

2014-02-01T23:59:59.000Z

313

Assessment of Industrial Load for Demand Response across Western Interconnect  

SciTech Connect (OSTI)

Demand response (DR) has the ability to both increase power grid reliability and potentially reduce operating system costs. Understanding the role of demand response in grid modeling has been difficult due to complex nature of the load characteristics compared to the modeled generation and the variation in load types. This is particularly true of industrial loads, where hundreds of different industries exist with varying availability for demand response. We present a framework considering industrial loads for the development of availability profiles that can provide more regional understanding and can be inserted into analysis software for further study. The developed framework utilizes a number of different informational resources, algorithms, and real-world measurements to perform a bottom-up approach in the development of a new database with representation of the potential demand response resource in the industrial sector across the U.S. This tool houses statistical values of energy and demand response (DR) potential by industrial plant and geospatially locates the information for aggregation for different territories without proprietary information. This report will discuss this framework and the analyzed quantities of demand response for Western Interconnect (WI) in support of evaluation of the cost production modeling with power grid modeling efforts of demand response.

Alkadi, Nasr E [ORNL; Starke, Michael R [ORNL; Ma, Ookie [United States Department of Energy (DOE), Office of Efficiency and Renewable Energy (EERE)

2013-11-01T23:59:59.000Z

314

Pulsed laser planarization of metal films for multilevel interconnects  

SciTech Connect (OSTI)

Multilevel interconnect schemes for integrated circuits generally require one or more planarization steps, in order to maintain an acceptably flat topography for lithography and thin-film step coverage on the higher levels. Traditional approaches have involved planarization of the interlevel insulation (dielectric) layers, either by spin-on application (e.g., polyimide), or by reflow (e.g., phosphosilicate glass). We have pursued an alternative approach, in which each metal level is melted (hence planarized) using a pulsed laser prior to patterning. Short (approx.1 ..mu..s) pulses are used to preclude undesirable metallurgical reactions between the film, adhesion or barrier layer, and dielectric layer. Laser planarization of metals is particularly well suited to multilevel systems which include ground or power planes. Results are presented for planarization of gold films on SiO/sub 2/ dielectric layers using a flashlamp-pumped dye laser. The pulse duration is approx.1 ..mu..s, which allows the heat pulse to uniformly penetrate the gold while not penetrating substantially through the underlying SiO/sub 2/ (hence not perturbing the lower levels of metal). Excellent planarization of the gold films is achieved (less than 0.1 ..mu..m surface roughness, even starting with extreme topographic variations), as well as improved conductivity. To demonstrate the process, numerous planarized two-layer structures (transmission lines under a ground plane) were fabricated and characterized. 9 refs., 2 figs.

Tuckerman, D.B.; Schmitt, R.L.

1985-05-01T23:59:59.000Z

315

Multi-attribute Model for Assessment of SMEs adoption of  

E-Print Network [OSTI]

Multi-attribute Model for Assessment of SMEs adoption of High Performance Computing Cloud Services boosters for SMEs, particularly manufacturing. · Huge amount of and $ are currently being spent on simulation experiments through various initiatives. #12;Introduction · Technology adoptance is in its early

Bohanec, Marko

316

Internet Protocol Adoption: Learning from Bitcoin Position Paper  

E-Print Network [OSTI]

This position paper discusses two related questions: 1. Using the framework of network economics, what are success factors behind the adoption of Bitcoin (a cryptographic curreny), and can we copy them for other protocols? 2. Can we design more successful protocols if we have inband payment mechanisms to internalize the externalities that emerge during adoption and in steady state? 1.

Rainer BŲhme; Westfšlische Wilhelms-universitšt MŁnster

317

Oahu Wind Integration and Transmission Study (OWITS): Hawaiian Islands Transmission Interconnection Project  

SciTech Connect (OSTI)

This report provides an independent review included an initial evaluation of the technical configuration and capital costs of establishing an undersea cable system and examining impacts to the existing electric transmission systems as a result of interconnecting the islands.

Woodford, D.

2011-02-01T23:59:59.000Z

318

Energy Scalability of On-Chip Interconnection Networks in Multicore Architectures  

E-Print Network [OSTI]

On-chip interconnection networks (OCNs) such as point-to-point networks and buses form the communication backbone in systems-on-a-chip, multicore processors, and tiled processors. OCNs can consume significant portions of ...

Agarwal, Anant

2008-11-11T23:59:59.000Z

319

Reliability of Multi-Terminal Copper Dual-Damascene Interconnect Trees  

E-Print Network [OSTI]

Electromigration tests on different Cu dual-damascene interconnect tree structures consisting of various numbers of straight via-to-via lines connected at the common middle terminal have been carried out. Like Al-based ...

Gan, C.L.

320

Determination of Interfacial Adhesion Strength between Oxide Scale and Substrate for Metallic SOFC Interconnects  

SciTech Connect (OSTI)

The interfacial adhesion strength between the oxide scale and the substrate is crucial to the reliability and durability of metallic interconnects in SOFC operating environments. It is necessary, therefore, to establish a methodology to quantify the interfacial adhesion strength between the oxide scale and the metallic interconnect substrate, and furthermore to design and optimize the interconnect material as well as the coating materials to meet the design life of an SOFC system. In this paper, we present an integrated experimental/analytical methodology for quantifying the interfacial adhesion strength between oxide scale and a ferritic stainless steel interconnect. Stair-stepping indentation tests are used in conjunction with subsequent finite element analyses to predict the interfacial strength between the oxide scale and Crofer 22 APU substrate.

Sun, Xin; Liu, Wenning N.; Stephens, Elizabeth V.; Khaleel, Mohammad A.

2008-01-21T23:59:59.000Z

Note: This page contains sample records for the topic "adopted interconnection standards" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


321

Fast Algorithms for High Frequency Interconnect Modeling in VLSI Circuits and Packages  

E-Print Network [OSTI]

to handle multiple dielectrics and magnetic materials. In this research, we solve three problems in interconnect modeling for high frequency circuits and packages. 1) Multiple dielectrics are common in integrated circuits and packages. We propose the first...

Yi, Yang

2011-02-22T23:59:59.000Z

322

ACTIVE SUBSTRATES FOR OPTOELECTRONIC INTERCONNECT Donald Chiarulli, Steven Levitan, Jason Bakos  

E-Print Network [OSTI]

ACTIVE SUBSTRATES FOR OPTOELECTRONIC INTERCONNECT Donald Chiarulli, Steven Levitan, Jason Bakos Semiconductor ABSTRACT We present the design of an intelligent optoelectronic chip carrier (IOCC the sapphire. The result is an optoelectronic package that supports full CMOS performance, is mechanically

Bakos, Jason D.

323

Process based cost modeling of emerging optoelectronic interconnects : implications for material platform choice  

E-Print Network [OSTI]

Continuously increasing demand for processing power, storage capacity, and I/O capacity in personal computing, data network, and display interface suggests that optical interconnects may soon supplant copper not only for ...

Liu, Shan, S.M. Massachusetts Institute of Technology

2008-01-01T23:59:59.000Z

324

High-performance parallel processors based on star-coupled wavelength division multiplexing optical interconnects  

DOE Patents [OSTI]

As the performance of individual elements within parallel processing systems increases, increased communication capability between distributed processor and memory elements is required. There is great interest in using fiber optics to improve interconnect communication beyond that attainable using electronic technology. Several groups have considered WDM, star-coupled optical interconnects. The invention uses a fiber optic transceiver to provide low latency, high bandwidth channels for such interconnects using a robust multimode fiber technology. Instruction-level simulation is used to quantify the bandwidth, latency, and concurrency required for such interconnects to scale to 256 nodes, each operating at 1 GFLOPS performance. Performance scales have been shown to .apprxeq.100 GFLOPS for scientific application kernels using a small number of wavelengths (8 to 32), only one wavelength received per node, and achievable optoelectronic bandwidth and latency.

Deri, Robert J. (Pleasanton, CA); DeGroot, Anthony J. (Castro Valley, CA); Haigh, Ronald E. (Arvada, CO)

2002-01-01T23:59:59.000Z

325

Record of Decision for the Electrical Interconnection of the Windy Point Wind Energy Project.  

SciTech Connect (OSTI)

The Bonneville Power Administration (BPA) has decided to offer contract terms for interconnection of 250 megawatts (MW) of power to be generated by the proposed Windy Point Wind Energy Project (Wind Project) into the Federal Columbia River Transmission System (FCRTS). Windy Point Partners, LLC (WPP) propose to construct and operate the proposed Wind Project and has requested interconnection to the FCRTS. The Wind Project will be interconnected at BPA's Rock Creek Substation, which is under construction in Klickitat County, Washington. The Rock Creek Substation will provide transmission access for the Wind Project to BPA's Wautoma-John Day No.1 500-kilovolt (kV) transmission line. BPA's decision to offer terms to interconnect the Wind Project is consistent with BPA's Business Plan Final Environmental Impact Statement (BP EIS) (DOE/EIS-0183, June 1995), and the Business Plan Record of Decision (BP ROD, August 15, 1995). This decision thus is tiered to the BP ROD.

United States. Bonneville Power Administration.

2006-11-01T23:59:59.000Z

326

EIS-0438: Interconnection of the Proposed Hermosa West Wind Farm Project, Albany County, Wyoming  

Broader source: Energy.gov [DOE]

After the applicant withdrew its request to interconnect the proposed Hermosa West Wind Farm Project with Western Area Power Administrationís transmission system, Western cancelled preparation of an EIS to evaluate the potential environmental impacts of the proposal.

327

ELECTRIFICATION OF ISOLATED AREAS BY INTERCONNECTING DIFFERENT RENEWABLE SOURCES OF ENERGY: A SUSTANAIBLE APPROACH  

E-Print Network [OSTI]

development integration of different aspects: > human > social > technical > economic > environmental FirstELECTRIFICATION OF ISOLATED AREAS BY INTERCONNECTING DIFFERENT RENEWABLE SOURCES OF ENERGY intend to join their efforts to develop a technique to generate electricity from primary renewable

328

Relevance of Generation Interconnection Procedures to Feed-in Tariffs in the United States  

SciTech Connect (OSTI)

Feed-in tariffs (FITs) have been used to promote renewable electricity development in over 40 countries throughout the past two decades. These policies generally provide guaranteed prices for the full system output from eligible generators for a fixed time period (typically 15-20 years). Due in part to the success of FIT policies in Europe, some jurisdictions in the United States are considering implementing similar policies, and a few have already put such policies in place. This report is intended to offer some guidance to policymakers and regulators on how generator interconnection procedures may affect the implementation of FITs and how state generator interconnection procedures can be formulated to support state renewable energy objectives. This report is based on a literature review of model interconnection procedures formulated by several organizations, as well as other documents that have reviewed, commented on, and in some cases, ranked state interconnection procedures.

Fink, S.; Porter, K.; Rogers, J.

2010-10-01T23:59:59.000Z

329

Design of a decentralized detection filter for a class of interconnected LTI systems  

E-Print Network [OSTI]

In this thesis, we consider the problem of designing a decentralized detection filter for a class of homogeneous interconnected systems. In this class of systems, all subsystems have an identical structure. A fault in a subsystem propagates via...

Shankar, Shamanth

2001-01-01T23:59:59.000Z

330

The Influence of Adjacent Segment on the Reliability of Cu Dual Damascene Interconnects  

E-Print Network [OSTI]

Three terminal ‚??dotted-Ií interconnect structures, with vias at both ends and an additional via in the middle, were tested under various test conditions. Mortalities (failures) were found in right segments with jL value ...

Chang, Choon Wai

331

Guest Editorial for Special Issue on High-Performance Multichip Interconnections  

E-Print Network [OSTI]

The ten papers in this special issue focus on high-performance multichip interconnections. The papers span novel transmitter and receiver equalization and data-recovery architectures, channel architecture organizations, ...

Stojanovic, Vladimir Marko

332

Reliable low latency I/O in torus-based interconnection networks  

E-Print Network [OSTI]

In today's high performance computing environment I/O remains the main bottleneck in achieving the optimal performance expected of the ever improving processor and memory technologies. Interconnection networks therefore combines processing units...

Azeez, Babatunde

2007-04-25T23:59:59.000Z

333

Fully Integrated Graphene and Carbon Nanotube Interconnects for Gigahertz High-Speed Cmos Electronics  

E-Print Network [OSTI]

Carbon-based nanomaterials such as metallic single-walled carbon nanotubes, multiwalled carbon nanotubes (MWCNTs), and graphene have been considered as some of the most promising candidates for future interconnect technology ...

Chen, Xiangyu

334

EIS-0437: Interconnection of the Buffalo Ridge III Wind Project, Brookings and Deuel Counties, South Dakota  

Broader source: Energy.gov [DOE]

This EIS evaluates the environmental impacts of a proposal to interconnect the Heartland Wind, LLC, proposed Buffalo Ridge III Wind Project in Brookings and Deuel Counties, South Dakota, to DOEís Western Area Power Administration transmission system.

335

Priority Based Switch Allocator in Adaptive Physical Channel Regulator for On Chip Interconnects  

E-Print Network [OSTI]

Chip multiprocessors (CMPs) are now popular design paradigm for microprocessors due to their power, performance and complexity advantages where a number of relatively simple cores are integrated on a single die. On chip interconnection network (No...

Mahapatra, Sonali

2014-08-04T23:59:59.000Z

336

Reuse Distance Based Circuit Replacement in Silicon Photonic Interconnection Networks for HPC  

E-Print Network [OSTI]

-scale distance, can help to further scale data-movement capabilities in high performance computing (HPC demands within high performance computing (HPC) systems. Silicon photonic (SiP) interconnects [1-3], which

Bergman, Keren

337

Phase 2 Report: Oahu Wind Integration and Transmission Study (OWITS); Hawaiian Islands Transmission Interconnection Project  

SciTech Connect (OSTI)

This report provides an independent review including an initial evaluation of the technical configuration and capital costs of establishing an undersea cable system and examining impacts to the existing electric transmission systems as a result of interconnecting the islands

Woodford, D.

2011-02-01T23:59:59.000Z

338

Demonstration of monolithically integrated graphene interconnects for low-power CMOS applications  

E-Print Network [OSTI]

In recent years, interconnects have become an increasingly difficult design challenge as their relative performance has not improved at the same pace with transistor scaling. The specifications for complex features, clock ...

Lee, Kyeong-Jae

2011-01-01T23:59:59.000Z

339

Innovative Distributed Power Grid Interconnection and Control Systems: Final Report, December 11, 2000 - August 30, 2005  

SciTech Connect (OSTI)

The contract goal was to further advance distributed generation in the marketplace by making installations more cost-effective and compatible with existing systems. This was achieved by developing innovative grid interconnection and control systems.

DePodesta, K.; Birlingmair, D.; West, R.

2006-03-01T23:59:59.000Z

340

Renewable Generation and Interconnection to the Electrical Grid in Southern California  

Broader source: Energy.gov [DOE]

Presentation covers the topic of "Renewable Generation and Interconnection to the Electrical Grid in Southern California," given at the Spring 2010 Federal Utility Partnership Working Group (FUPWG) meeting in Providence, Rhode Island.

Note: This page contains sample records for the topic "adopted interconnection standards" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


341

E-Print Network 3.0 - at-speed interconnect bist Sample Search...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Explorit Topic List Advanced Search Sample search results for: at-speed interconnect bist Page: << < 1 2 3 4 5 > >> 1 JOURNAL OF ELECTRONIC TESTING: Theory and Applications 19,...

342

Pricing Games among Interconnected Microgrids Gaurav S. Kasbekar and Saswati Sarkar  

E-Print Network [OSTI]

1 Pricing Games among Interconnected Microgrids Gaurav S. Kasbekar and Saswati Sarkar Abstract than, less than or as much aggregate power as it requires. G. Kasbekar and S. Sarkar

Sarkar, Saswati

343

ELECTR-5939; No of Pages 6 Please cite this article in press as: A. Sopinka, Variable Energy Resources: VERy Interesting Implications for the Western Interconnect, Electr. J. (2013), http://dx.doi.org/10.1016/j.tej.2013.04.015  

E-Print Network [OSTI]

Resources: VERy Interesting Implications for the Western Interconnect, Electr. J. (2013), http Interconnect Variable energy resources (VERs) are growing in the Western Interconnect. To backstop The North American bulk power system is comprised of four interconnected regions: the Western Interconnect

Pedersen, Tom

344

THOR Concept Complex simulation Autonomous control Conclusion Interconnection of the behavior-based control  

E-Print Network [OSTI]

Schmidt Interconnection of iB2C and a detailed machine model rrlab.cs.uni-kl.de 2 #12;THOR Concept Complex of iB2C and a detailed machine model rrlab.cs.uni-kl.de 3 #12;THOR Concept Complex simulation Schmidt Interconnection of iB2C and a detailed machine model rrlab.cs.uni-kl.de 5 #12;THOR Concept Complex

Berns, Karsten

345

Submitter Email: nathalie.revol@ens-lyon.fr Type of Project: New IEEE Standard  

E-Print Network [OSTI]

with a similar scope? No 7.2 International Activities a. Adoption Is there potential for this standard (in part or in whole) to be adopted by another national, regional or international organization? Yes Organization: ISOP1788 Submitter Email: nathalie.revol@ens-lyon.fr Type of Project: New IEEE Standard PAR Request

Kreinovich, Vladik

346

Upgrade of the LHC magnet interconnections thermal shielding  

SciTech Connect (OSTI)

The about 1700 interconnections (ICs) between the Large Hadron Collider (LHC) superconducting magnets include thermal shielding at 50-75 K, providing continuity to the thermal shielding of the magnet cryostats to reduce the overall radiation heat loads to the 1.9 K helium bath of the magnets. The IC shield, made of aluminum, is conduction-cooled via a welded bridge to the thermal shield of the adjacent magnets which is actively cooled. TIG welding of these bridges made in the LHC tunnel at installation of the magnets induced a considerable risk of fire hazard due to the proximity of the multi-layer insulation of the magnet shields. A fire incident occurred in one of the machine sectors during machine installation, but fortunately with limited consequences thanks to prompt intervention of the operators. LHC is now undergoing a 2 years technical stop during which all magnet's ICs will have to be opened to consolidate the magnet electrical connections. The IC thermal shields will therefore have to be removed and re-installed after the work is completed. In order to eliminate the risk of fire hazard when re-welding, it has been decided to review the design of the IC shields, by replacing the welded bridges with a mechanical clamping which also preserves its thermal function. An additional advantage of this new solution is the ease in dismantling for maintenance, and eliminating weld-grinding operations at removal needing radioprotection measures because of material activation after long-term operation of the LHC. This paper describes the new design of the IC shields and in particular the theoretical and experimental validation of its thermal performance. Furthermore a status report of the on-going upgrade work in the LHC is given.

Musso, Andrea; Barlow, Graeme; Bastard, Alain; Charrondiere, Maryline; Deferne, Guy; Dib, GaŽlle; Duret, Max; Guinchard, Michael; Prin, Hervť; Craen, Arnaud Vande; Villiger, Gilles [CERN European Organization for Nuclear Research, Meyrin 1211, Geneva 23, CH (Switzerland); Chrul, Anna [The Henryk Niewodniczanski Institute of Nuclear Physics, Polish Academy of Sciences, ul.Radzikowskiego 152, 31-324 Krakow (Poland); Damianoglou, Dimitrios [NTUA National Technical University of Athens, Heeron Polytechniou 9, 15780 Zografou (Greece); Strychalski, Micha? [Wroclaw University of Technology, Faculty of Mechanical and Power Engineering, Wyb. Wyspianskiego 27, Wroclaw, 50-370 (Poland); Wright, Loren [Lancaster University, Bailrigg, Lancaster, LA1 4YW (United Kingdom)

2014-01-29T23:59:59.000Z

347

Data interchange standards for biotechnology: Issues and alternatives  

SciTech Connect (OSTI)

This report outlines a framework for discussion of what aspects of biotechnical information might be good candidates for guidelines or standards, what existing data exchange standards might be appropriate building blocks upon which to build, and what procedural mechanisms might be appropriate for adoption of such guidelines or standards. It builds on experience from other scientific communities which have already benefitted from development of discipline-specific data exchange standards. 33 refs.

McCarthy, J.L.

1990-06-01T23:59:59.000Z

348

1michigan state university brand STandardS BRAND STANDARDS  

E-Print Network [OSTI]

1michigan state university brand STandardS BRAND STANDARDS VERSION 4, APRIL 30, 2012 #12;2michigan state university brand STandardS TABLE OF CONTENTS 3 brand baSicS 5 The Michigan STaTe UniverSiTy brandUrTher gUidance #12;3michigan state university brand STandardS 1. BrANd BASICS 1a whaT iS a brand? We build

349

Quality Management and Job Quality: How the ISO 9001 Standard forQuality Management Systems Affects Employees and Employers  

E-Print Network [OSTI]

and Job Quality: How the ISO 9001 Standard for Qualityhave examined how the ISO 9001 Quality Management Systemcompanies in California. ISO 9001 adopters subsequently had

Levine, David I.; Toffel, Michael W.

2008-01-01T23:59:59.000Z

350

Standards, Ethics  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May JunDatastreamsmmcrcalgovInstrumentsrucLas ConchasPassiveSubmittedStatus TomAbout ¬Ľ Staff Basic Energy Sciences (BES)Standards for

351

Textbook Adoption Application Guide Entering the Application ..................................................................................... 2  

E-Print Network [OSTI]

allows you to search for your assigned course(s) by: Term, Location, Academic Department, Course NumberTextbook Adoption Application Guide Entering the Application ............................................................................................................ 3 Search with Academic Criteria

Sura, Philip

352

Energy prices and the adoption of energy-saving technology  

E-Print Network [OSTI]

This paper investigates the link between factor prices, technology and factor demands. I estimate the effect of price-induced technology adoption on energy demand in the U.S. manufacturing sector, using plant data from the ...

Linn, Joshua

2006-01-01T23:59:59.000Z

353

Village adoption scheme : a model for rural development  

E-Print Network [OSTI]

The study describes a "Village Adoption Scheme" as a model for energising the rural economy in India and to slow down rural - urban migration which research has shown to be harmful to both; rural and urban people of India ...

Nanavati, Shahid Sadruddin, 1961-

2004-01-01T23:59:59.000Z

354

Electronic Discovery and the Adoption of Information Technology  

E-Print Network [OSTI]

After firms adopt electronic information and communication technologies, their decision-making leaves a trail of electronic information that may be more extensive and accessible than a paper trail. We ask how the expected ...

Tucker, Catherine Elizabeth

355

Revised Record of Decision for the Electrical Interconnection of the Summit/Westward Project  

SciTech Connect (OSTI)

The Bonneville Power Administration (BPA) has decided to amend its July 25, 2003, Record of Decision (ROD) regarding the proposed Summit/Westward Project (Project) to offer contract terms for an optional interconnection of this Project into the Federal Columbia River Transmission System (FCRTS). Under this optional interconnection plan, BPA would integrate electric power from the Project into the FCRTS at a point adjacent to Clatskanie People's Utility District (CPUD) existing Wauna Substation. In order to deliver power to this location, CPUD would develop a new substation (Bradbury Substation) at a site near the Project and a new 230-kV transmission line from there to CPUD's Wauna Substation, which is already connected to the FCRTS. As part of this revised decision, BPA will facilitate CPUD development of the Bradbury-Wauna transmission line by allowing joint use of BPA right-of-way. This will involve reconstructing a section of BPA's 115-kV Allston-Astoria No. 1 transmission line from single-circuit H-frame wood-pole design to double-circuit single metal pole design. Terms of BPA participation in CPUD's development of the Bradbury-Wauna transmission line will be documented in a Construction Agreement. This optional interconnection plan is in addition to BPA's previous offer for interconnection of the Project at BPA's Allston Substation, as documented in the July 25, 2003, ROD. As with the initial interconnection plan, the decision to offer terms to interconnect the Project through the optional interconnection plan is consistent with BPA's Business Plan Final Environmental Impact Statement (BP EIS) (DOE/EIS-0183, June 1995), and the Business Plan Record of Decision (BP ROD, August 1995). This decision thus is similarly tiered to the Business Plan ROD.

N /A

2004-10-21T23:59:59.000Z

356

1994 DOE Technical Standards Program Workshop: Proceedings  

SciTech Connect (OSTI)

The DOE Technical Standards Program has been structured to provide guidance and assistance for the development, adoption, and use of voluntary standards within the Department. OMB Circular A-119, ``Federal Participation in the Development and Use of Voluntary Standards`` establishes the policy to be followed in working with voluntary standards bodies, and in adopting and using voluntary standards whenever feasible. The DOE Technical Standards Program is consistent with this policy and is dedicated to the task of promoting its implementation. The theme of this year`s workshop is ``Standards Initiatives in Environmental Management fostering the development and use of industry standards for safe, environmentally responsible operations.`` The objective of the workshop is to increase the participant`s awareness of the standardization activities taking place nationally and internationally and the impact of these activities on their efforts, and to facilitate the exchange of experiences, processes, and tools for implementing the program. Workshop sessions will include presentations by industry and Government notables in the environment, safety, and health arena with ample opportunity for everyone to ask questions and share experiences. There will be a breakout session which will concentrate on resolution of issues arising from the implementation of the DOE Technical Standards Program and a plenary session to discuss the plans developed by the breakout groups. Many organizations provide services and products which support the development, processing, distribution, and retrieval of standards. Those organizations listed at the end of the agenda will have exhibits available for your perusal throughout the workshop. Last year`s workshop was very successful in stimulating an understanding of an interest in the standards program. This year, we hope to build on that success and provide an environment for the synergism of ideas to enhance the program and advance its implementation.

Spellman, D.J.

1994-12-31T23:59:59.000Z

357

Factors determining the adoption or non-adoption of precision agriculture by producers across the cotton belt  

E-Print Network [OSTI]

The purpose of this study was to determine factors influencing cotton producer adoption of Precision Agriculture in the cotton belt according to members of the American Cotton Producers of the National Cotton Council. The National Research Council...

Lavergne, Christopher Bernard

2006-04-12T23:59:59.000Z

358

Distributed energy resources customer adoption modeling with combined heat and power applications  

SciTech Connect (OSTI)

In this report, an economic model of customer adoption of distributed energy resources (DER) is developed. It covers progress on the DER project for the California Energy Commission (CEC) at Berkeley Lab during the period July 2001 through Dec 2002 in the Consortium for Electric Reliability Technology Solutions (CERTS) Distributed Energy Resources Integration (DERI) project. CERTS has developed a specific paradigm of distributed energy deployment, the CERTS Microgrid (as described in Lasseter et al. 2002). The primary goal of CERTS distributed generation research is to solve the technical problems required to make the CERTS Microgrid a viable technology, and Berkeley Lab's contribution is to direct the technical research proceeding at CERTS partner sites towards the most productive engineering problems. The work reported herein is somewhat more widely applicable, so it will be described within the context of a generic microgrid (mGrid). Current work focuses on the implementation of combined heat and power (CHP) capability. A mGrid as generically defined for this work is a semiautonomous grouping of generating sources and end-use electrical loads and heat sinks that share heat and power. Equipment is clustered and operated for the benefit of its owners. Although it can function independently of the traditional power system, or macrogrid, the mGrid is usually interconnected and exchanges energy and possibly ancillary services with the macrogrid. In contrast to the traditional centralized paradigm, the design, implementation, operation, and expansion of the mGrid is meant to optimize the overall energy system requirements of participating customers rather than the objectives and requirements of the macrogrid.

Siddiqui, Afzal S.; Firestone, Ryan M.; Ghosh, Srijay; Stadler, Michael; Edwards, Jennifer L.; Marnay, Chris

2003-07-01T23:59:59.000Z

359

Plastic deformation in Al (Cu) interconnects stressed by electromigration and studied by synchrotron polychromatic X-ray microdiffraction  

E-Print Network [OSTI]

Plastic deformation in Al (Cu) interconnects stressed bygrain orientation [7], study plastic deformation [12-15] andThis aspect of EM-induced plastic deformation in grains

Chen, Kai; Advanced Light Source; UCLA

2008-01-01T23:59:59.000Z

360

California Greenhouse Gas Emissions Standards for Light-Duty Vehicles (Update) (released in AEO2006)  

Reports and Publications (EIA)

The state of California was given authority under the Clean Air Act Amendments of 1990 (CAAA90) to set emissions standards for light-duty vehicles that exceed federal standards. In addition, other states that do not comply with the National Ambient Air Quality Standards (NAAQS) set by the Environmental Protection Agency under CAAA90 were given the option to adopt Californias light-duty vehicle emissions standards in order to achieve air quality compliance. CAAA90 specifically identifies hydrocarbon, carbon monoxide, and NOx as vehicle-related air pollutants that can be regulated. California has led the nation in developing stricter vehicle emissions standards, and other states have adopted the California standards.

2006-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "adopted interconnection standards" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


361

Thin-film chip-to-substrate interconnect and methods for making same  

DOE Patents [OSTI]

Integrated circuit chips are electrically connected to a silica wafer interconnection substrate. Thin film wiring is fabricated down bevelled edges of the chips. A subtractive wire fabrication method uses a series of masks and etching steps to form wires in a metal layer. An additive method direct laser writes or deposits very thin metal lines which can then be plated up to form wires. A quasi-additive or subtractive/additive method forms a pattern of trenches to expose a metal surface which can nucleate subsequent electrolytic deposition of wires. Low inductance interconnections on a 25 micron pitch (1600 wires on a 1 cm square chip) can be produced. The thin film hybrid interconnect eliminates solder joints or welds, and minimizes the levels of metallization. Advantages include good electrical properties, very high wiring density, excellent backside contact, compactness, and high thermal and mechanical reliability.

Tuckerman, David B. (Livermore, CA)

1991-01-01T23:59:59.000Z

362

Thin-film chip-to-substrate interconnect and methods for making same  

DOE Patents [OSTI]

Integrated circuit chips are electrically connected to a silicon wafer interconnection substrate. Thin film wiring is fabricated down bevelled edges of the chips. A subtractive wire fabrication method uses a series of masks and etching steps to form wires in a metal layer. An additive method direct laser writes or deposits very thin lines which can then be plated up to form wires. A quasi-additive or subtractive/additive method forms a pattern of trenches to expose a metal surface which can nucleate subsequent electrolytic deposition of wires. Low inductance interconnections on a 25 micron pitch (1600 wires on a 1 cm square chip) can be produced. The thin film hybrid interconnect eliminates solder joints or welds, and minimizes the levels of metallization. Advantages include good electrical properties, very high wiring density, excellent backside contact, compactness, and high thermal and mechanical reliability. 6 figs.

Tuckerman, D.B.

1988-06-06T23:59:59.000Z

363

Interconnections between various analytic approaches applicable to third-order nonlinear differential equations  

E-Print Network [OSTI]

We unearth the interconnection between various analytical methods which are widely used in the current literature to identify integrable nonlinear dynamical systems described by third-order nonlinear ordinary differentiable equations (ODEs). We establish an important interconnection between extended Prelle-Singer procedure and {\\lambda}-symmetries approach applicable to third-order ODEs to bring out the various linkages associated with these different techniques. By establishing this interconnection we demonstrate that given any one of the quantities as a starting point in the family consisting of Jacobi last multipliers, Darboux polynomials, Lie point symmetries, adjoint-symmetries, {\\lambda}-symmetries, integrating factors and null forms one can derive the rest of the quantities in this family in a straightforward and unambiguous manner. We also illustrate our findings with three specific examples.

R. Mohanasubha; V. K. Chandrasekar; M. Senthilvelan; M. Lakshmanan

2015-02-13T23:59:59.000Z

364

Sandia National Laboratories: Updating Interconnection Screens for PV  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr MayAtmosphericNuclear Security Administration the1 -theErikGroundbreakingStandardsTCESJBEI

365

Analysis of electric vehicle interconnection with commercial building microgrids  

SciTech Connect (OSTI)

The outline of this presentation is: (1) global concept of microgrid and electric vehicle (EV) modeling; (2) Lawrence Berkeley National Laboratory's Distributed Energy Resources Customer Adoption Model (DER-CAM); (3) presentation summary - how does the number of EVs connected to the building change with different optimization goals (cost versus CO{sub 2}); (3) ongoing EV modeling for California: the California commercial end-use survey (CEUS) database, objective: 138 different typical building - EV connections and benefits; (4) detailed analysis for healthcare facility: optimal EV connection at a healthcare facility in southern California; and (5) conclusions. Conclusions are: (1) EV Charging/discharging pattern mainly depends on the objective of the building (cost versus CO{sub 2}); (2) performed optimization runs show that stationary batteries are more attractive than mobile storage when putting more focus on CO{sub 2} emissions. Why? Stationary storage is available 24 hours a day for energy management - more effective; (3) stationary storage will be charged by PV, mobile only marginally; (4) results will depend on the considered region and tariff - final work will show the results for 138 different buildings in nine different climate zones and three major utility service territories.

Stadler, Michael; Mendes, Goncalo; Marnay, Chris; M& #233; gel, Olivier; Lai, Judy

2011-04-01T23:59:59.000Z

366

September 2004 Standards Forum and Standards Actions  

Broader source: Energy.gov (indexed) [DOE]

16 Cancellation in Progress - 3 Inside This Issue Visit the Technical Standards Program Web Site at http:tis.eh.doe.govtechstds September 2004 The Standards Forum and...

367

Development of Readout Interconnections for the Si-W Calorimeter of SiD  

SciTech Connect (OSTI)

The SiD collaboration is developing a Si-W sampling electromagnetic calorimeter, with anticipated application for the International Linear Collider. Assembling the modules for such a detector will involve special bonding technologies for the interconnections, especially for attaching a silicon detector wafer to a flex cable readout bus. We review the interconnect technologies involved, including oxidation removal processes, pad surface preparation, solder ball selection and placement, and bond quality assurance. Our results show that solder ball bonding is a promising technique for the Si-W ECAL, and unresolved issues are being addressed.

Woods, M.; Fields, R.G.; Holbrook, B.; Lander, R.L.; Moskaleva, A.; Neher, C.; Pasner, J.; Tripathi, M.; /UC, Davis; Brau, J.E.; Frey, R.E.; Strom, D.; /Oregon U.; Breidenbach, M.; Freytag, D.; Haller, G.; Herbst, R.; Nelson, T.; /SLAC; Schier, S.; Schumm, B.; /UC, Santa Cruz

2012-09-14T23:59:59.000Z

368

Proposal to negotiate amendments to an existing contract for the assembly of interconnections for the LHC  

E-Print Network [OSTI]

This document concerns the proposal to negotiate amendments to the existing contract for the assembly of interconnections for the LHC. For the reasons explained in this document, the Finance Committee is invited to approve amendments to the existing contract with the consortium INEO (FR), ENDEL (FR) and GTI (NL) for the assembly of interconnections for the LHC for a total amount of 5 181 403 euros (8 095 424 Swiss francs), subject to revision, bringing the total amount of the contract to a maximum of 14 974 239 euros (23 395 751 Swiss francs), subject to revision. The amounts in Swiss francs have been calculated using the present rate of exchange.

2006-01-01T23:59:59.000Z

369

Method of bonding an interconnection layer on an electrode of an electrochemical cell  

DOE Patents [OSTI]

An electrochemical cell containing an air electrode, contacting electrolyte and electronically conductive interconnection layer, and a fuel electrode, has the interconnection layer attached by: (A) applying a thin, closely packed, discrete layer of LaCrO[sub 3] particles, doped with an element selected from the group consisting of Ca, Sr, Co, Ba, Mg and their mixtures on a portion of the air electrode, and then (B) electrochemical vapor depositing a dense skeletal structure between and around the doped LaCrO[sub 3] particles. 2 figs.

Pal, U.B.; Isenberg, A.O.; Folser, G.R.

1992-01-14T23:59:59.000Z

370

Wind/PV Generation for Frequency Regulation and Oscillation Damping in the Eastern Interconnection  

SciTech Connect (OSTI)

This report presents the control of renewable energy sources, including the variable-speed wind generators and solar photovoltaic (PV) generators, for frequency regulation and inter-area oscillation damping in the U.S. Eastern Interconnection (EI). In this report, based on the user-defined wind/PV generator electrical control model and the 16,000-bus Eastern Interconnection dynamic model, the additional controllers for frequency regulation and inter-area oscillation damping are developed and incorporated and the potential contributions of renewable energy sources to the EI system frequency regulation and inter-area oscillation damping are evaluated.

Liu, Yong [The University of Tennessee, Knoxville; Gracia, Jose R [ORNL; Hadley, Stanton W [ORNL; Liu, Yilu [ORNL

2013-12-01T23:59:59.000Z

371

Development of Readout Interconnections for the Si-W Calorimeter of SiD  

E-Print Network [OSTI]

The SiD collaboration is developing a Si-W sampling electromagnetic calorimeter, with anticipated application for the International Linear Collider. Assembling the modules for such a detector will involve special bonding technologies for the interconnections, especially for attaching a silicon detector wafer to a flex cable readout bus. We review the interconnect technologies involved, including oxidation removal processes, pad surface preparation, solder ball selection and placement, and bond quality assurance. Our results show that solder ball bonding is a promising technique for the Si-W ECAL, and unresolved issues are being addressed.

M. Woods; R. G. Fields; B. Holbrook; R. L. Lander; A. Moskaleva; C. Neher; J. Pasner; M. Tripathi; J. E. Brau; R. E. Frey; D. Strom; M. Breidenbach; D. Freytag; G. Haller; R. Herbst; T. Nelson; S. Schier; B. Schumm

2011-11-21T23:59:59.000Z

372

A Model of U.S. Commercial Distributed Generation Adoption  

SciTech Connect (OSTI)

Small-scale (100 kW-5 MW) on-site distributed generation (DG) economically driven by combined heat and power (CHP) applications and, in some cases, reliability concerns will likely emerge as a common feature of commercial building energy systems over the next two decades. Forecasts of DG adoption published by the Energy Information Administration (EIA) in the Annual Energy Outlook (AEO) are made using the National Energy Modeling System (NEMS), which has a forecasting module that predicts the penetration of several possible commercial building DG technologies over the period 2005-2025. NEMS is also used for estimating the future benefits of Department of Energy research and development used in support of budget requests and management decisionmaking. The NEMS approach to modeling DG has some limitations, including constraints on the amount of DG allowed for retrofits to existing buildings and a small number of possible sizes for each DG technology. An alternative approach called Commercial Sector Model (ComSeM) is developed to improve the way in which DG adoption is modeled. The approach incorporates load shapes for specific end uses in specific building types in specific regions, e.g., cooling in hospitals in Atlanta or space heating in Chicago offices. The Distributed Energy Resources Customer Adoption Model (DER-CAM) uses these load profiles together with input cost and performance DG technology assumptions to model the potential DG adoption for four selected cities and two sizes of five building types in selected forecast years to 2022. The Distributed Energy Resources Market Diffusion Model (DER-MaDiM) is then used to then tailor the DER-CAM results to adoption projections for the entire U.S. commercial sector for all forecast years from 2007-2025. This process is conducted such that the structure of results are consistent with the structure of NEMS, and can be re-injected into NEMS that can then be used to integrate adoption results into a full forecast.

LaCommare, Kristina Hamachi; Ryan Firestone; Zhou, Nan; Maribu,Karl; Marnay, Chris

2006-01-10T23:59:59.000Z

373

Long-Distance Interconnection as Solar Resource Intermittency Solution: Optimizing the Use of Energy Storage and the Geographic  

E-Print Network [OSTI]

of Energy Storage and the Geographic Dispersion + Interconnection of Solar Generating Facilities. Marc J. R energy targets. Variability of the solar resource occurs across many different temporal scales: from energy storage and Long-distance interconnection coupled with geographic dispersion of solar generating

374

Understanding Digital Library Adoption: A Use Diffusion Approach  

E-Print Network [OSTI]

be motivated by the thought of potential harvest gains to be the first farmer in the region to try out a new@colorado.edu Manuel Gerardo Saldivar Institute of Cognitive Science School of Education University of Colorado Boulder digital libraries, the need for automatic methods capable of characterizing adoption and use has grown. We

Bradley, Elizabeth

375

Siemens Global Studio Project: Experiences Adopting an Integrated GSD Infrastructure  

E-Print Network [OSTI]

Siemens Global Studio Project: Experiences Adopting an Integrated GSD Infrastructure Mullick, N., Bass, M., El Houda, Z., and Paulish, D.J. Siemens Corporate Research, Inc Princeton, NJ Neel.Mullick, Matthew.Bass, Daniel.Paulish @Siemens.com Cataldo, M. and Herbsleb, J.D. Institute for Software Research

Herbsleb, James D.

376

Systematic review Systematic review of organizational motivations for adopting  

E-Print Network [OSTI]

Staples a,b,*, Mahmood Niazi c a National ICT Australia, Australian Technology Park, Eveleigh, NSW 1430, especially Small and Medium Enter- prises (SMEs). As part of a larger project about the adop- tion of CMMI by SMEs, we have previously reported on a study of why SMEs do not adopt CMMI [23]. To comple- ment

377

Operating Procedures University Curriculum Committee Adopted April 20, 2001  

E-Print Network [OSTI]

Operating Procedures ­ University Curriculum Committee Adopted April 20, 2001 Rev. November 1, 2013 by its own authority review, modify, delete, augment, and amend the procedures set forth in the Curriculum Policies and Procedures Manual. Changes and the effective dates for changes shall be publicized

378

Grid Applications: From Early Adopters to Mainstream Users  

E-Print Network [OSTI]

Grid Applications: From Early Adopters to Mainstream Users Thilo Kielmann (guest editor) Vrije Universiteit, Amsterdam, The Netherlands April 24, 2006 Grid computing has gained widespread attention, both in academic and commercial settings. As a result, the development of grid middleware infras- tructure has made

Kielmann, Thilo

379

FEDERAL INFORMATION PROCESSING STANDARD  

E-Print Network [OSTI]

March 2004 FEDERAL INFORMATION PROCESSING STANDARD (FIPS) 199, STANDARDS FOR SECURITY Information Technology Laboratory National Institute of Standards and Technology A new Federal Information Processing Standard (FIPS), recently approved by the Secretary of Commerce, will help federal agencies

380

E-Print Network 3.0 - activities resolution adopted Sample Search...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

asks the company to adopt an 11-point code... , 2004) Resolution: Adopt Code of Conduct for China operations. ACIR Recommendation: The Committee... ) Resolution: The...

Note: This page contains sample records for the topic "adopted interconnection standards" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


381

E-Print Network 3.0 - adoptively transferred natural Sample Search...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

innovation. Then, we suggest indicators likely to characterize the nature of adoption. (IPR... in the second section we comment the innovation adoption according to the nature of...

382

Impact of Wind Turbine Penetration on the Dynamic Performance of Interconnected Power Systems  

E-Print Network [OSTI]

to stability problems caused by wind power integration. In the grid impact studies of wind power integrationImpact of Wind Turbine Penetration on the Dynamic Performance of Interconnected Power Systems M. J connected to a higher voltage level, their impact is becoming more widespread. The European Wind Energy

Pota, Himanshu Roy

383

Can Software Reliability Outperform Hardware Reliability in High-Performance Interconnects?  

E-Print Network [OSTI]

Can Software Reliability Outperform Hardware Reliability in High-Performance Interconnects? A Case, Myrinet, InfiniBand, and others HPC networks are generally quite reliable without additional protocols link With this in mind, how should reliability be implemented? 3 #12;Onload or Offload? Some networks

Panda, Dhabaleswar K.

384

Changing photovoltaic array interconnections to reduce mismatch losses: a case study  

E-Print Network [OSTI]

) ­ Grenoble, France **Grupo de Investigacion y Desarollo en Energia Solar y Automatica (IDEA) ­ Jaén, Spain a wide variety of plants ranging from utility-sized solar trackers to residential building-integrated PV, resulting in lower energy production yields. The traditional series-parallel interconnection scheme of solar

Boyer, Edmond

385

Interconnected Slums: Water, Sanitation and Health in Abidjan, Co^te d'Ivoire  

E-Print Network [OSTI]

Interconnected Slums: Water, Sanitation and Health in Abidjan, Co^te d'Ivoire BRIGIT OBRIST, GUE contributed to this paper are: Gue¬īladio Cisse¬ī (Centre Suisse de Recherches Scientifiques, Abidjan, Co^te d'Ivoire¬ītude de cas comparative, il examine les re¬īponses aux proble`mes environnementaux dans un contexte aussi

Richner, Heinz

386

Transparent, Low Power Optical WDM Interface for Off-Chip Interconnects  

E-Print Network [OSTI]

, and other related circuitry (e.g. for thermal stability). In CMOS technology [6], the total power dissipated static power dissipation of the interface. The dynamic power is proportional to the gate capacitance (CTransparent, Low Power Optical WDM Interface for Off-Chip Interconnects Odile Liboiron

Bergman, Keren

387

An energy vision: the transformation towards sustainability --interconnected challenges and solutions  

E-Print Network [OSTI]

(RCPs) [2 ], the International Energy Agency's World Energy Outlook [3,4 ], and several modeAn energy vision: the transformation towards sustainability -- interconnected challenges Nilsson8 and KR Smith9 The energy system is currently facing a number of challenges, most notably high

Silver, Whendee

388

Optimization of Interconnects Between Accelerators and Shared Memories in Dark Silicon Jason Cong and Bingjun Xiao  

E-Print Network [OSTI]

Optimization of Interconnects Between Accelerators and Shared Memories in Dark Silicon Jason Cong, 90095 {cong, xiao}@cs.ucla.edu Abstract--Application-specific accelerators provide orders-of- magnitude improvement in energy-efficiency over CPUs, and accelerator-rich computing platforms are showing promise

Cong, Jason "Jingsheng"

389

Selection and Evaluation of Heat-Resistant Alloys for Planar SOFC Interconnect Applications  

SciTech Connect (OSTI)

Over the past several years, the steady reduction in SOFC operating temperatures to the intermediate range of 700~850oC [1] has made it feasible for lanthanum chromite to be supplanted by metals or alloys as the interconnect materials. Compared to doped lanthanum chromite, metals or alloys offer significantly lower raw material and fabrication costs. However, to be a durable and reliable, a metal or alloy has to satisfy several functional requirements specific to the interconnect under SOFC operating conditions. Specifically, the interconnect metal or alloy should possess the following properties: (i) Good surface stability (resistance to oxidation, hot corrosion, and carburization) in both cathodic (air) and anodic (fuel) atmospheres; (ii) Thermal expansion matching to the ceramic PEN (positive cathode-electrolyte-negative anode) and seal materials (as least for a rigid seal design); (iii) High electrical conductivity through both the bulk material and in-situ formed oxide scales; (iv) Bulk and interfacial thermal mechanical reliability and durability at the operating temperature; (v) Compatibility with other materials in contact with interconnects such as seals and electrical contact materials.

Yang, Z Gary; Weil, K. Scott; Paxton, Dean M.; Stevenson, Jeffry W.

2002-11-21T23:59:59.000Z

390

Risk analysis via heterogeneous models of SCADA interconnecting Power Grids and Telco Networks  

E-Print Network [OSTI]

for an electrical power distribution grid. The modeling techniques we discuss aim at providing a probabilistic demonstrate their applicability by modeling and #12;analyzing an actual SCADA system for an electrical powerRisk analysis via heterogeneous models of SCADA interconnecting Power Grids and Telco Networks A

Tronci, Enrico

391

EA-1884: Invenergy Interconnection for the Wray Wind Energy Project, Town of Wray, Yuma County, CO  

Broader source: Energy.gov [DOE]

DOEís Western Area Power Administration is preparing this EA to evaluate the environmental impacts of interconnecting the proposed Wray Wind Energy Project, for approximately 90 megawatts of wind generation, to Westernís existing Wray Substation in Yuma County, Colorado.

392

Modeling and Simulation Environment for Photonic Interconnection Networks in High Performance Computing  

E-Print Network [OSTI]

at the scale of high performance computer clusters and warehouse scale data centers, system level simulations and results for rack scale photonic interconnection networks for high performance computing. Keywords: optical to the newsworthy power consumption [3], latency [4] and bandwidth challenges [5] of high performance computing (HPC

Bergman, Keren

393

Solid oxide fuel cell with single material for electrodes and interconnect  

DOE Patents [OSTI]

A solid oxide fuel cell is described having a plurality of individual cells. A solid oxide fuel cell has an anode and a cathode with electrolyte disposed there between, and the anode, cathode and interconnect elements are comprised of substantially one material. 9 figs.

McPheeters, C.C.; Nelson, P.A.; Dees, D.W.

1994-07-19T23:59:59.000Z

394

CarPal: interconnecting overlay networks for a community-driven shared mobility  

E-Print Network [OSTI]

CarPal: interconnecting overlay networks for a community-driven shared mobility VincenzoName.lastName@sophia.inria.fr Abstract. Car sharing and car pooling have proven to be an effective solution to reduce the amount of such effectiveness. Keywords. Peer to peer, overlay networks, case study, information retrieval, car sharing 1

Paris-Sud XI, Université de

395

Optically Interconnected Data Center Architecture for Bandwidth Intensive Energy Efficient Networking  

E-Print Network [OSTI]

Optically Interconnected Data Center Architecture for Bandwidth Intensive Energy Efficient) 854 2900, e-mail: howard@ee.columbia.edu ABSTRACT The relentless rise of data-intensive cloud will either be prohibitively costly, overly complex, or result in unsustainable energy requirements. Network

Bergman, Keren

396

EIS-0485: Interconnection of the Grande Prairie Wind Farm, Holt County, Nebraska  

Broader source: Energy.gov [DOE]

DOEís Western Area Power Administration is preparing an EIS to evaluate the environmental impacts of interconnecting the proposed Grande Prairie Wind Farm, in Holt County, near OíNeill, Nebraska, to Westernís power transmission system. The project website is http://www.wapa.gov/ugp/Environment/GrandePrairie.htm.

397

Interconnection phenomena in $W^+W^-$ and $t\\bar t$ events  

E-Print Network [OSTI]

I will attempt to survey some selected physics issues on QCD interconnection phenomena in the processes $e^+e^-\\to W^+W^-\\to$ 4 jets and $e^+e^-\\to t\\bar t \\to b W^+\\bar b W^-$. Possible consequences for LEP2 and future linear $e^+e^-$ colliders are briefly discussed.

Valery A. Khoze

1998-05-29T23:59:59.000Z

398

Synthesis of electrical networks interconnecting PZT actuators to damp mechanical vibrations  

E-Print Network [OSTI]

This paper proves that it is possible to damp mechanical vibrations of some beam frames by means of piezoelectric actuators interconnected via passive networks. We create a kind of electromechanical wave guide where the electrical velocity group equals the mechanical one thus enabling an electromechanical energy transfer. Numerical simulations are presented which prove the technical feasibility of proposed device

F. dell'Isola; E. G. Henneke; M. Porfiri

2010-08-30T23:59:59.000Z

399

Advanced Unit Commitment Strategies for the U.S. Eastern Interconnection: Preprint  

SciTech Connect (OSTI)

This paper outlines a study undertaken for the U.S. Eastern Interconnection in which different advanced unit commitment strategies were simulated for three different years to evaluate the benefits that may occur from using these strategies as an operational tool.

Ela, E.; Milligan, M.; Meibom, P.; Barth, R.; Tuohy, A.

2010-10-01T23:59:59.000Z

400

HVDC Control Strategies to Improve Transient Stability in Interconnected Power Systems  

E-Print Network [OSTI]

HVDC Control Strategies to Improve Transient Stability in Interconnected Power Systems J. Hazra Dpt of Li`ege, Belgium, dernst@ulg.ac.be Abstract--This paper presents three HVDC modulation strate- gies flow settings through the HVDC-links. The proposed techniques are tested on the IEEE 24-Bus reliability

Boyer, Edmond

Note: This page contains sample records for the topic "adopted interconnection standards" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


401

Transient Analysis of a CMOS Inverter Driving Resistive Interconnect Kevin T. Tang and Eby G. Friedman  

E-Print Network [OSTI]

are characterized by the th power law model. In order to emphasize the nonlinear behavior of a CMOS inverterTransient Analysis of a CMOS Inverter Driving Resistive Interconnect Kevin T. Tang and Eby G. Friedman Department of Electrical and Computer Engineering University of Rochester Rochester, New York

Friedman, Eby G.

402

A Self-Reconfigurable Lightweight Interconnect for Scalable Processor Fabrics Heiner Giefers and Marco Platzner  

E-Print Network [OSTI]

, energy, and execution time. Therefore it is of high interest to also study alternative interconnects compile-time informa- tion and reconfigures the global network due to program demands. We consider data of the switch's ports. Communication within a sub-bus is established by broadcasting to the bus segment

Hellebrand, Sybille

403

Application Of Ti-Based Self-Formation Barrier Layers To Cu Dual-Damascene Interconnects  

SciTech Connect (OSTI)

Cu interconnects have been used extensively in ULSI devices. However, large resistance-capacitance delay and poor device reliability have been critical issues as the device feature size has reduced to nanometer scale. In order to achieve low resistance and high reliability of Cu interconnects, we have applied a thin Ti-based self-formed barrier (SFB) using Cu(Ti) alloy seed to 45nm-node dual damascene interconnects and evaluated its performance. The line resistance and via resistance decreased significantly, compared with those of conventional Ta/TaN barriers. The stress migration performance was also drastically improved using the SFB process. A performance of time dependent dielectric breakdown revealed superior endurance. These results suggest that the Ti-based SFB process is one of the most promising candidates for advanced Cu interconnects. TEM and X-ray photoelectron spectroscopy observations for characterization of the Ti-based SFB structure were also performed. The Ti-based SFB consisted of mainly amorphous Ti oxides. Amorphous or crystalline Ti compounds such as TiC, TiN, and TiSi formed beneath Cu alloy films, and the formation varied with dielectric.

Ito, Kazuhiro; Kohama, Kazuyuki [Department of Materials Science and Engineering, Kyoto University, Kyoto 606-8501 (Japan); Ohmori, Kazuyuki; Mori, Kenichi; Maekawa, Kazuyoshi; Asai, Koyu [Process Technology Div., Renesas Electronics Corporation, Hitachinaka, Ibaraki 312-8504 (Japan); Murakami, Masanori [The Ritsumeikan Trust, Nakagyo-ku, Kyoto 604-8520 (Japan)

2010-11-24T23:59:59.000Z

404

Effect of Via Separationand Low-k Dielectric Materials on the Thermal Characteristics of Cu Interconnects  

E-Print Network [OSTI]

Effect of Via Separationand Low-k Dielectric Materials on the Thermal Characteristics of Cu in low-k based interconnect structures by providing lower thermal resistance paths. In this paper that the temperature is highly dependent on the via separation. A 3-D electro-thermal simulation methodology using

405

WHAT IS A NETWORK? (Gas and Electricity) A complex, interconnected group or  

E-Print Network [OSTI]

WHAT IS A NETWORK? (Gas and Electricity) A complex, interconnected group or system Electricity and Gas: A system used to distribute electricity and gas around the world/certain area, by compromising to minimise costs and generate the most electricity and gas as possible, which maximises profits

Wright, Francis

406

Phase 1 - Evaluation of a Functional Interconnect System for Solid Oxide Fuel Cells  

SciTech Connect (OSTI)

This project is focused on evaluating the suitability of materials and complex multi-materials systems for use as solid oxide fuel cell interconnects. ATI Allegheny Ludlum has generated promising results for interconnect materials which incorporate modified surfaces. Methods for producing these surfaces include cladding, which permits the use of novel materials, and modifications via unique thermomechanical processing, which allows for the modification of materials chemistry. The University of Pittsburgh is assisting in this effort by providing use of their in-place facilities for dual atmosphere testing and ASR measurements, along with substantial work to characterize post-exposure specimens. Carnegie Mellon is testing interconnects for chromia scale spallation resistance using macro-scale and nano-scale indentation tests. Chromia spallation can increase electrical resistance to unacceptable levels and interconnect systems must be developed that will not experience spallation within 40,000 hours at operating temperatures. Spallation is one of three interconnect failure mechanisms, the others being excessive growth of the chromia scale (increasing electrical resistance) and scale evaporation (which can poison the cathode). The goal of indentation fracture testing at Carnegie Mellon is to accelerate the evaluation of new interconnect systems (by inducing spalls at after short exposure times) and to use fracture mechanics to understand mechanisms leading to premature interconnect failure by spallation. Tests include bare alloys from ATI and coated systems from DOE Laboratories and industrial partners, using ATI alloy substrates. West Virginia University is working towards developing a cost-effective material for use as a contact material in the cathode chamber of the SOFC. Currently materials such as platinum are well suited for this purpose, but are cost-prohibitive. For the solid-oxide fuel cell to become a commercial reality it is imperative that lower cost components be developed. Based on the results obtained to date, it appears that sterling silver could be an inexpensive, dependable candidate for use as a contacting material in the cathode chamber of the solid-oxide fuel cell. Although data regarding pure silver samples show a lower rate of thickness reduction, the much lower cost of sterling silver makes it an attractive alternative for use in SOFC operation.

James M. Rakowski

2006-09-30T23:59:59.000Z

407

Flexibility Reserve Reductions from an Energy Imbalance Market with High Levels of Wind Energy in the Western Interconnection  

SciTech Connect (OSTI)

The anticipated increase in variable generation in the Western Interconnection (WI) over the next several years has raised concerns about how to maintain system balance, especially in smaller Balancing Areas (BAs). Given renewable portfolio standards in the West, it is possible that more than 50 gigawatts (GW) of wind capacity will be installed by 2020. Significant quantities of solar generation are likely to be added as well. The consequent increase in variability and uncertainty that must be managed by the conventional generation fleet and responsive load make it attractive to consider ways in which Balancing Area Authorities (BAAs) can pool their variability and response resources, thus taking advantage of geographic and temporal diversity to increase overall operational efficiency. Our analysis considers several alternative forms of an Energy Imbalance Market (EIM) that have been proposed in the non-market areas of the WI. The proposed EIM includes two changes in operating practices that independently reduce variability and increase access to responsive resources: BAA cooperation and sub-hourly dispatch. As proposed, the EIM does not consider any form of coordinated unit commitment; however, over time it is possible that BAAs would develop formal or informal coordination plans. This report examines the benefits of several possible EIM implementations, both separately and in concert.

King, J.; Kirby, B.; Milligan, M.; S. Beuning

2011-10-01T23:59:59.000Z

408

Summary of 2008 Building Energy Efficiency Standards Changes Summary of Changes For  

E-Print Network [OSTI]

Summary of 2008 Building Energy Efficiency Standards Changes Summary of Changes For California 2008 Building Energy Efficiency Standards Mazi Shirakh, P.E. Project Manager, Building Energy Efficiency Standards Buildings and Appliances Office California Energy Commission Adopted on April 23, 2008 #12;Summary

409

Vers une adoption de la France ? Hugh Clout1  

E-Print Network [OSTI]

sur la n√©cessit√© d'acqu√©rir une connaissance des langues √©trang√®res, de Cole Harris sur l sont vraiment int√©ressants. Au contraire, il y a un petit article de la plume de William Mead, publi√© en 1963 et intitul√© ¬ę The adoption of other lands ¬Ľ, qui me semble plein de bon sens. Mead √©tait, et

Paris-Sud XI, Université de

410

Regulatory Considerations Associated with the Expanded Adoption of Distributed Solar  

SciTech Connect (OSTI)

Increased adoption of distributed PV, and other forms of distributed generation, have the potential to affect utility-customer interactions, system costs recovery, and utility revenue streams. If a greater number of electricity customers choose to self-generate, demand for system power will decrease and utility fixed costs will have to be recovered over fewer kilowatt hours of sales. As such, regulators will need to determine the value and cost of additional distributed PV and determine the appropriate allocation of the costs and benefits among consumers. The potential for new business models to emerge also has implications for regulation and rate structures that ensure equitable solutions for all electricity grid users. This report examines regulatory tools and rate designs for addressing emerging issues with the expanded adoption of distributed PV and evaluates the potential effectiveness and viability of these options going forward. It offers the groundwork needed in order for regulators to explore mechanisms and ensure that utilities can collect sufficient revenues to provide reliable electric service, cover fixed costs, and balance cost equity among ratepayers -- while creating a value proposition for customers to adopt distributed PV.

Bird, L.; McLaren, J.; Heeter, J.; Linvill, C.; Shenot, J.; Sedano, R.; Migden-Ostrander, J.

2013-11-01T23:59:59.000Z

411

The Standard Model Beyond the Standard Model  

E-Print Network [OSTI]

physics with top quark Search for Extra-dimensions Conclusions 1 The Standard Model Building block quark Search for Extra-dimensions Conclusions Building block The particles and forces The Standard Model the Standard Model New physics with top quark Search for Extra-dimensions Conclusions Building block

412

ANSI/MSE 2000: A Single Standard for Diverse Business Sectors  

E-Print Network [OSTI]

The Energy and Environmental Management Center (EEMC), part of the Georgia Tech Economic Development Institute, has developed a comprehensive energy management standard, officially adopted by ANSI, to identify and achieve energy management goals...

Brown, M. L.; Zinga, S.

2002-01-01T23:59:59.000Z

413

EA-1774: Energy Conservation Program: Energy Conservation Standards for Direct Heating Equipment  

Broader source: Energy.gov [DOE]

This EA evaluates the environmental impacts of the adoption of amended energy conservation standards as required by The Energy Policy and Conservation Act, as amended) for direct heating equipment,...

414

Optimal Planning and Operation of Smart Grids with Electric Vehicle Interconnection  

E-Print Network [OSTI]

for the available PV, solar thermal, and EV parking lots atphotovoltaic (PV), solar thermal, stationary batteries,maximum possible PV and solar thermal adoption as well as

Stadler, Michael

2012-01-01T23:59:59.000Z

415

Optimal Planning and Operation of Smart Grids with Electric Vehicle Interconnection  

E-Print Network [OSTI]

storage [GWh] combined heat and power (CHP) and otheron Microgrid Combined Heat and Power Adoption,Ē Journal ofcarbon emissions, combined heat and power, commercial

Stadler, Michael

2012-01-01T23:59:59.000Z

416

Post-processing of polymer foam tissue scaffolds with high power ultrasound: a route to increased pore interconnectivity, pore size and fluid transport  

E-Print Network [OSTI]

We expose thick polymer foam tissue scaffolds to high power ultrasound and study its effect on the openness of the pore architecture and fluid transport through the scaffold. Our analysis is supported by measurements of fluid uptake during insonification and imaging of the scaffold microstructure via x-ray computed tomography, scanning electron microscopy and acoustic microscopy. The ultrasonic treatment is found to increase the mean pore size by over 10%. More striking is the improvement in fluid uptake: for scaffolds with only 40% water uptake via standard immersion techniques, we can routinely achieve full saturation of the scaffold over approximately one hour of exposure. These desirable modifications occur with no loss of scaffold integrity and negligible mass loss, and are optimized when the ultrasound treatment is coupled to a pre-wetting stage with ethanol. Our findings suggest that high power ultrasound is a highly targetted and efficient means to promote pore interconnectivity and fluid transport in thick foam tissue scaffolds.

N J Watson; R K Johal; Y Reinwald; L J White; A M Ghaemmaghami; S P Morgan; F R A J Rose; M J W Povey; N G Parker

2013-02-18T23:59:59.000Z

417

County Wind Ordinance Standards  

Broader source: Energy.gov [DOE]

[http://www.leginfo.ca.gov/pub/09-10/bill/asm/ab_0001-0050/ab_45_bill_200... Assembly Bill 45] of 2009 authorized counties to adopt ordinances to provide for the installation of small wind systems ...

418

A novel design for monolithic interconnected modules (MIMs) for thermophotovoltaic (TPV) power conversion  

SciTech Connect (OSTI)

The design for the fabrication of Monolithic Interconnected Modules (MIMs) for thermophotovoltaic (TPV) power conversion described in this paper utilizes a novel, interdigitated contacting scheme that increases the flexibility in the size of the component cells and hence the output current and voltage of the module. This flexibility is gained at the expense of only minimally increased grid obscuration. Because the design uses the grid fingers of the component cells as the interconnect structure, the area of the device used for this purpose becomes negligible. In this paper the authors report on the specifics of the design as well as issues related to the fabrication of the modules. Preliminary performance data for representative modules also are offered.

Ward, J.S.; Duda, A.; Wanlass, M.W. [National Renewable Energy Lab., Golden, CO (United States)] [and others

1997-06-01T23:59:59.000Z

419

Bipolar plating of metal contacts onto oxide interconnection for solid oxide electrochemical cell  

DOE Patents [OSTI]

Disclosed is a method of forming an adherent metal deposit on a conducting layer of a tube sealed at one end. The tube is immersed with the sealed end down into an aqueous solution containing ions of the metal to be deposited. An ionically conducting aqueous fluid is placed inside the tube and a direct current is passed from a cathode inside the tube to an anode outside the tube. Also disclosed is a multi-layered solid oxide fuel cell tube which consists of an inner porous ceramic support tube, a porous air electrode covering the support tube, a non-porous electrolyte covering a portion of the air electrode, a non-porous conducting interconnection covering the remaining portion of the electrode, and a metal deposit on the interconnection.

Isenberg, Arnold O. (Forest Hills Boro, PA)

1987-01-01T23:59:59.000Z

420

On certain analytical methods in finding integrable systems and their interconnections  

E-Print Network [OSTI]

In this paper, to begin with, we review six different analytical methods which are widely used to derive symmetries, integrating factors, multipliers, Darboux polynomials and integrals of second order nonlinear ordinary differential equations. We illustrate the algorithm behind each method by considering a nonlinear oscillator equation as an example. In the second part of this paper, we examine the interconnections between these methods. We establish a road map between extended Prelle-Singer procedure with all other methods cited above and thereby demonstrate the interplay between Lie point symmetries, $\\lambda$-symmetries, adjoint symmetries, null forms, integrating factors, Darboux polynomials, and Jacobi multipliers of second order integrable ODEs. The interconnections are illustrated with the same example finally.

R. Mohanasubha; V. K. Chandrasekar; M. Senthilvelan; M. Lakshmanan

2015-02-13T23:59:59.000Z

Note: This page contains sample records for the topic "adopted interconnection standards" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


421

Interconnection arrangement of routers of processor boards in array of cabinets supporting secure physical partition  

DOE Patents [OSTI]

A multiple processor computing apparatus includes a physical interconnect structure that is flexibly configurable to support selective segregation of classified and unclassified users. The physical interconnect structure includes routers in service or compute processor boards distributed in an array of cabinets connected in series on each board and to respective routers in neighboring row cabinet boards with the routers in series connection coupled to routers in series connection in respective neighboring column cabinet boards. The array can include disconnect cabinets or respective routers in all boards in each cabinet connected in a toroid. The computing apparatus can include an emulator which permits applications from the same job to be launched on processors that use different operating systems.

Tomkins, James L. (Albuquerque, NM); Camp, William J. (Albuquerque, NM)

2007-07-17T23:59:59.000Z

422

Environmental Standardization for Sustainability  

E-Print Network [OSTI]

Environmental Standardization for Sustainability by Professor John W. Bagby College of Information that environmental controls are expressed as environmental standards, a traditional driver of investment in pollution control. Environmental standards spur investment in green technologies that promise to stimulate

Bagby, John

423

August 2007 Standards Actions  

Broader source: Energy.gov (indexed) [DOE]

August 2007 1.5 DOE Technical Standards Published No entries were received in August 2007 2.0 Non-Government Standards Actions 2.1 American National Standards Institute (ANSI)...

424

July 2007 Standards Actions  

Broader source: Energy.gov (indexed) [DOE]

in June 2007 1.5 DOE Technical Standards Published No entries were received in June 2007 2.0 Non-Government Standards Actions 2.1 American National Standards Institute (ANSI)...

425

October 2006 Standards Actions  

Broader source: Energy.gov (indexed) [DOE]

Project No. SAFT-0109 Continued on next page Standards Actions Page 2 October 2006 2.0 NON-GOVERNMENT STANDARDS ACTIONS 2.1 American National Standards Institute American...

426

July 2006 Standards Actions  

Broader source: Energy.gov (indexed) [DOE]

were received in June 2006. Continued on next page Standards Actions Page 2 July 2005 2.0 Non-Government Standards Actions 2.1 American National Standards Institute (ANSI)...

427

Communication Standards and Recommendations  

E-Print Network [OSTI]

Communication Standards and Recommendations Introduction & Purpose 3 Standards & Recommendations Communication 4 Training 10 Evaluation 11 PMO Workgroup Participation 12 Staffing 12 Communications-related Tracking Grantee Portal Standards and Recommendations 13

428

Status of cool roof standards in the United States  

SciTech Connect (OSTI)

Since 1999, several widely used building energy efficiency standards, including ASHRAE 90.1, ASHRAE 90.2, the International Energy Conservation Code, and California's Title 24 have adopted cool roof credits or requirements. We review the technical development of cool roof provisions in the ASHRAE 90.1, ASHRAE 90.2, and California Title 24 standards, and discuss the treatment of cool roofs in other standards and energy-efficiency programs. The techniques used to develop the ASHRAE and Title 24 cool roof provisions can be used as models to address cool roofs in building energy standards worldwide.

Akbari, Hashem; Levinson, Ronnen

2007-06-01T23:59:59.000Z

429

System Impacts from Interconnection of Distributed Resources: Current Status and Identification of Needs for Further Development  

SciTech Connect (OSTI)

This report documents and evaluates system impacts from the interconnection of distributed resources to transmission and distribution systems, including a focus on renewable distributed resource technologies. The report also identifies system impact-resolution approaches and actions, including extensions of existing approaches. Lastly, the report documents the current challenges and examines what is needed to gain a clearer understanding of what to pursue to better avoid or address system impact issues.

Basso, T. S.

2009-01-01T23:59:59.000Z

430

Viscosity Solutions of Systems of PDEs with Interconnected Obstacles and Switching Problem  

SciTech Connect (OSTI)

This paper deals with existence and uniqueness of a solution in viscosity sense, for a system of m variational partial differential inequalities with inter-connected obstacles. A particular case is the Hamilton-Jacobi-Bellmann system of the Markovian stochastic optimal m-states switching problem. The switching cost functions depend on (t,x). The main tool is the notion of systems of reflected backward stochastic differential equations with oblique reflection.

Hamadene, S., E-mail: hamadene@univ-lemans.fr; Morlais, M. A., E-mail: Marie_Amelie.Morlais@univ-lemans.fr [Universite du Maine, LMM (France)

2013-04-15T23:59:59.000Z

431

Examination of Potential Benefits of an Energy Imbalance Market in the Western Interconnection  

SciTech Connect (OSTI)

In the Western Interconnection, there is significant interest in improving approaches to wide-area coordinated operations of the bulk electric power system, in part because of the increasing penetration of variable generation. One proposed solution is an energy imbalance market. This study focused on that approach alone, with the goal of identifying the potential benefits of an energy imbalance market in the year 2020.

Milligan, M.; Clark, K.; King, J.; Kirby, B.; Guo, T.; Liu, G.

2013-03-01T23:59:59.000Z

432

Corrosion and Protection of Metallic Interconnects in Solid Oxide Fuel Cells  

SciTech Connect (OSTI)

Energy security and increased concern over environmental protection have spurred a dramatic world-wide growth in research and development of fuel cells, which electrochemically convert incoming fuel into electricity with no or low pollution. Fuel cell technology has become increasingly attractive to a number of sectors, including utility, automotive, and defense industries. Among the various types of fuel cells, solid oxide fuel cells (SOFCs) operate at high temperature (typically 650-1,000 C) and have advantages in terms of high conversion efficiency and the flexibility of using hydrocarbon fuels, in addition to hydrogen. The high temperature operation, however, can lead to increased mass transport and interactions between the surrounding environment and components that are required to be stable during a lifetime of thousands of hours and up to hundreds of thermal cycles. For stacks with relatively low operating temperatures (<800 C), the interconnects that are used to electrically connect a number of cells in series are typically made from cost-effective metals or alloys. The metallic interconnects must demonstrate excellent stability in a very challenging environment during SOFC operation, as they are simultaneously exposed to both an oxidizing (air) environment on the cathode side and a reducing environment (hydrogen or a reformed hydrocarbon fuel) on the anode side. Other challenges include the fact that water vapor is likely to be present in both of these environments, and the fuel is likely to contain impurities, such as sulfides. Since the fuel is usually a reformed hydrocarbon fuel, such as natural gas, coal gas, biogas, gasoline, etc., the interconnect is exposed to a wet carbonaceous environment at the anode side. Finally, the interconnect must be stable towards any adjacent components, such as electrodes, seals and electrical contact materials, with which it is in physical contact.

Yang, Z Gary; Stevenson, Jeffry W.; Singh, Prabhakar

2007-12-09T23:59:59.000Z

433

State-Level Comparison of Processes and Timelines for Distributed Photovoltaic Interconnection in the United States  

SciTech Connect (OSTI)

This report presents results from an analysis of distributed photovoltaic (PV) interconnection and deployment processes in the United States. Using data from more than 30,000 residential (up to 10 kilowatts) and small commercial (10-50 kilowatts) PV systems, installed from 2012 to 2014, we assess the range in project completion timelines nationally (across 87 utilities in 16 states) and in five states with active solar markets (Arizona, California, New Jersey, New York, and Colorado).

Ardani, K.; Davidson, C.; Margolis, R.; Nobler, E.

2015-01-01T23:59:59.000Z

434

May 2008 Standards Actions  

Broader source: Energy.gov (indexed) [DOE]

Standards Actions 2 American National Standards Institute (ANSI) 2 American Society of Mechanical Engineers (ASME) 2 ASTM International 2 American Nuclear Society...

435

May 2006 Standards Actions  

Broader source: Energy.gov (indexed) [DOE]

Standards Actions 1 American National Standards Institute (ANSI) 1 American Society of Mechanical Engineers (ASME) 2 ASTM International 2 American Nuclear Society...

436

February 2001 Standards Actions  

Broader source: Energy.gov (indexed) [DOE]

Technical Standards Program Document Status Visit the Technical Standards Program Web Site: http:tis.eh.doe.govtechstds Activity Summary In Conversion - 4 In Preparation...

437

Energy Portfolio Standard  

Broader source: Energy.gov [DOE]

Nevada established a renewable portfolio standard (RPS) as part of its 1997 restructuring legislation. Under the standard, NV Energy (formerly Nevada Power and Sierra Pacific Power) must use...

438

Energy Efficiency Product Standards  

Broader source: Energy.gov [DOE]

'' Note: The federal government has imposed and updated appliance efficiency standards through several legislative acts,* and now has standards in place or under development for 30 classes of...

439

Effect of interconnect creep on long-term performance of SOFC of one cell stacks  

SciTech Connect (OSTI)

Creep deformation becomes relevant for a material when the operating temperature is near or exceeds half of its melting temperature (in degrees of Kelvin). The operating temperatures for most of the solid oxide fuel cells (SOFC) under development in the SECA program are around 1073oK. High temperature ferritic alloys are potential candidates as interconnect (IC) materials and spacers due to their low cost and CTE compatibility with other SOFC components. Since the melting temperature of most stainless steel is around 1800oK, possible creep deformation of IC under the typical cell operating temperature should not be neglected. In this paper, the effects of interconnect creep behavior on stack geometry change and stress redistribution of different cell components are predicted and summarized. The goal of the study is to investigate the performance of the fuel cell stack by obtaining the fuel and air channel geometry changes due to creep of the ferritic stainless steel interconnect, therefore indicating possible SOFC performance change under long term operations. IC creep models were incorporated into SOFC-MP and Mentat FC, and finite element analyses were performed to quantify the deformed configuration of the SOFC stack under the long term steady state operating temperature. It is found that creep behavior of the ferritic stainless steel IC contributes to narrowing of both the fuel and the air flow channels. In addition, stress re-distribution of the cell components suggests the need for a compliant sealing material that also relaxes at operating temperature.

Liu, Wenning N.; Sun, Xin; Khaleel, Mohammad A.

2008-02-01T23:59:59.000Z

440

Life Prediction of Coated and Uncoated Metallic Interconnect for Solid Oxide Fuel Cell Applications  

SciTech Connect (OSTI)

Oxidation reaction of the ferritic stainless interconnects in a typical SOFC working environment is unavoidable and the thickness of the oxide scale will continue to grow with operating time, even with protective coatings. The interfacial strength of the various interfaces for the uncoated and coated ferritic interconnects is crucial to long term performance of SOFCs. In this paper, we employ an integrated experimental/modeling approach to quantify the interfacial strength and to further predict the life of Crofer 22 APU as SOFC interconnect under isothermal cooling condition. The life of Crofer 22 APU was predicted by comparing the predicted interfacial strength, interfacial stresses induced by the cooling process from the operating temperature to room temperature, together with the growth kinetics of oxide scale with and without spinel coating. It was found that the interfacial strength between the oxide scale and Crofer 22 APU substrate decreases with the growth of the oxide scale. The interfacial strength of the oxide scale and spinel coating is much higher than that of the oxide scale and Crofer 22 APU substrate. With the spinel coating, the predicted life of the Crofer 22 APU is significantly longer than that of the uncoated Crofer 22 APU.

Liu, Wenning N.; Sun, Xin; Stephens, Elizabeth V.; Khaleel, Mohammad A.

2009-04-15T23:59:59.000Z

Note: This page contains sample records for the topic "adopted interconnection standards" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


441

Evaluation of a Surface Treatment on the Performance of Stainless Steels for SOFC Interconnect Applications  

SciTech Connect (OSTI)

Pack cementation-like Cerium based surface treatments have been found to be effective in enhancing the oxidation resistance of ferritic steels (Crofer 22APU) for solid oxide fuel cell (SOFC) applications. The application of either a CeN- or CeO2 based surface treatment results in a decrease in weight gain by a factor of three after 4000 hours exposure to air+3%H2O at 800oC. Similar oxide scales formed on treated and untreated surfaces, with a continuous Cr-Mn outer oxide layer and a continuous inner Cr2O3 layer formed on the surface. However, the thickness of the scales, and the amount of internal oxidation were significantly reduced with the treatment, leading to the decrease in oxidation rate. This presentation will detail the influence of the treatment on the electrical properties of the interconnect. Half-cell experiments (LSM cathode sandwiched between two steel interconnects) and full SOFC button cell experiments were run with treated and untreated interconnects. Preliminary results indicate the Ce treatment can improve SOFC performance.

Alman, D.E.; Holcomb, Adler, T.A.; G.R.; Wilson, R.D.; Jablonski, P.D.

2007-04-01T23:59:59.000Z

442

Dynamic Directories: A Mechanism for Reducing On-Chip Interconnect Power in Multicores  

E-Print Network [OSTI]

AbstractóOn-chip interconnection networks consume a significant fraction of the chipís power, and the rapidly increasing core counts in future technologies is going to further aggravate their impact on the chipís overall power consumption. A large fraction of the traffic originates not from data messages exchanged between sharing cores, but from the communication between the cores and intermediate hardware structures (i.e., directories) for the purpose of maintaining coherence in the presence of conflicting updates. In this paper, we propose Dynamic Directories, a method allowing the directories to be placed arbitrarily in the chip by piggy-backing the virtual to physical address translation. This eliminates a large fraction of the on-chip interconnect traversals, hence reducing the power consumption. Through trace-driven and cycle-accurate simulation in a range of scientific and Map-Reduce applications, we show that our technique reduces the power and energy expended by the on-chip interconnect by up to 37 % (16.4 % on average) with negligible hardware overhead and a small improvement in performance (1.3 % on average). 21 Keywords-On-chip networks; Non-uniform caches; Multicore architecture

Abhishek Das; Matt Schuchhardt; Nikos Hardavellas; Gokhan Memik; Alok Choudhary

443

Low-power approaches for parallel, free-space photonic interconnects  

SciTech Connect (OSTI)

Future advances in the application of photonic interconnects will involve the insertion of parallel-channel links into Multi-Chip Modules (MCMS) and board-level parallel connections. Such applications will drive photonic link components into more compact forms that consume far less power than traditional telecommunication data links. These will make use of new device-level technologies such as vertical cavity surface-emitting lasers and special low-power parallel photoreceiver circuits. Depending on the application, these device technologies will often be monolithically integrated to reduce the amount of board or module real estate required by the photonics. Highly parallel MCM and board-level applications will also require simplified drive circuitry, lower cost, and higher reliability than has been demonstrated in photonic and optoelectronic technologies. An example is found in two-dimensional point-to-point array interconnects for MCM stacking. These interconnects are based on high-efficiency Vertical Cavity Surface Emitting Lasers (VCSELs), Heterojunction Bipolar Transistor (HBT) photoreceivers, integrated micro-optics, and MCM-compatible packaging techniques. Individual channels have been demonstrated at 100 Mb/s, operating with a direct 3.3V CMOS electronic interface while using 45 mW of electrical power. These results demonstrate how optoelectronic device technologies can be optimized for low-power parallel link applications.

Carson, R.F.; Lovejoy, M.L.; Lear, K.L.; WSarren, M.E.; Seigal, P.K.; Craft, D.C.; Kilcoyne, S.P.; Patrizi, G.A.; Blum, O.

1995-12-31T23:59:59.000Z

444

EIS-0210: Tampa Electric Company-Polk Power Station (Adopted)  

Broader source: Energy.gov [DOE]

The U.S. Environmental Protection Agency prepared this statement to fulfill its National Environmental Policy Act requirements with respect to the potential issuance of a permit to the Tampa Electric Company under the National Pollutant Discharge Elimination System for the 1,150-MW Polk Power Station, a new pollutant source. The U.S. Department of Energy served as a cooperating agency in the development of this document due to its potential role to provide cost-shared financial assistance for a 260-MW Integrated Gasification Combined Cycle unit at the Power Station under its Clean Coal Technology Demonstration Project, and adopted the document by August 1994.

445

Design and implementation of a large integrated crossbar switch for a 256 x 256 x 8 interconnection network  

E-Print Network [OSTI]

is determined by a detailed yield analysis. Index Terms-Crossbar switch 7 buffer, delay, interconnection networks, packet, clock cycle, arbitration, performance, priority, yield analysis, latch, decoder, packaging, ball grid array....

Naik, Rajeshwar

1995-01-01T23:59:59.000Z

446

High-speed graphene interconnects monolithically integrated with CMOS ring oscillators operating at 1.3GHz  

E-Print Network [OSTI]

We have successfully experimentally integrated graphene interconnects with commercial 0.25 ¬Ņm technology CMOS ring oscillator circuit using conventional fabrication techniques, and demonstrated high speed on-chip graphene ...

Chen, Xiangyu

447

Turk J Elec Engin, VOL.17, NO.1 2009, c TUBITAK Accurate Prediction of Crosstalk for RC Interconnects  

E-Print Network [OSTI]

Interconnects Selahattin SAYIL, Merlyn RUDRAPATI Department of Electrical Engineering, Lamar University P.O. Box 10029, Beaumont, TX 77710, U.S.A. e-mail: sayil@ee.lamar.edu Abstract This work proposes an accurate

Sayil, Selahattin

448

Observation of Joule Heating-Assisted Electromigration Failure Mechanisms for Dual Damascene Cu/SiO? Interconnects  

E-Print Network [OSTI]

Failure mechanisms observed in electromigration (EM) stressed dual damascene Cu/SiO? interconnects trees were studied and simulated. Failure sites with ‚??melt patchí or ‚??craterí are common for test structures in the top ...

Chang, Choon Wai

449

Design and analysis of a 3-dimensional cluster multicomputer architecture using optical interconnection for petaFLOP computing  

E-Print Network [OSTI]

In this dissertation, the design and analyses of an extremely scalable distributed multicomputer architecture, using optical interconnects, that has the potential to deliver in the order of petaFLOP performance is presented in detail. The design...

Okorafor, Ekpe Apia

2007-04-25T23:59:59.000Z

450

Fatal Void Size Comparisons in Via-Below and Via-Above Cu Dual-Damascene Interconnects  

E-Print Network [OSTI]

The median-times-to-failure (t??ís) for straight dual-damascene via-terminated copper interconnect structures, tested under the same conditions, depend on whether the vias connect down to underlaying leads ...

Choi, Z.-S.

451

Full-wave Surface Integral Equation Method for Electromagnetic-circuit Simulation of Three-dimensional Interconnects in Layered Media  

E-Print Network [OSTI]

FULL-WAVE SURFACE INTEGRAL EQUATION METHOD FOR ELECTROMAGNETIC-CIRCUIT SIMULATION OF THREE-DIMENSIONAL INTERCONNECTS IN LAYERED MEDIA A Dissertation by NUR KURT KARSILAYAN Submitted to the Office of Graduate Studies of Texas A&M University... in partial fulfillment of the requirements for the degree of DOCTOR OF PHILOSOPHY May 2010 Major Subject: Electrical Engineering FULL-WAVE SURFACE INTEGRAL EQUATION METHOD FOR ELECTROMAGNETIC-CIRCUIT SIMULATION OF THREE-DIMENSIONAL INTERCONNECTS...

Karsilayan, Nur

2011-08-08T23:59:59.000Z

452

NIST Special Publication 800-25 National Institute of Standards  

E-Print Network [OSTI]

, and education with the standards adopted or recognized by the Federal Government. As an agency of the U's research facilities are located at Gaithersburg, MD 20899, and at Boulder, CO 80303. Major technical · National Programs · Program Development Electronics and Electrical Engineering Laboratory

453

Facilities Management CAD Standards  

E-Print Network [OSTI]

Facilities Management CAD Standards 2011 #12;Facilities Management CAD Standards Providing: Layering Standards 2.1 Layer Name Format 2.2 Layer Name Modifiers 2.3 Layer Attributes 2.4 Special Layer of PDF and DWG Files APPENDIX A: DAL FM CAD Standard Layers APPENDIX B: DAL FM CAD Special Layers

Brownstone, Rob

454

Standard 90, the planning  

SciTech Connect (OSTI)

In order to understand the current proposed ANS/ASHRAE/IES Standard 90.1 Energy Efficient Design of New Non-Residential Buildings and New High-Rise, Residential Buildings, this article offers background on the initial Standard, the organization of the Standard committee, and the objectives established for the proposed Standard 90.1.

Not Available

1985-10-01T23:59:59.000Z

455

Technical Standards Program  

Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

The Technical Standards Program (TSP) promotes the use of voluntary consensus standards by the Department of Energy (DOE), provides DOE with the means to develop needed technical standards, and manages overall technical standards information, activities, issues, and interactions. Cancels DOE O 1300.2A. Canceled by DOE O 252.1A

1999-11-19T23:59:59.000Z

456

Technical Standards Program  

Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

The Order promotes DOE's use of Voluntary Consensus Standards (VCS) as the primary method for application of technical standards and establishes and manages the DOE Technical Standards Program (TSP) including technical standards development, information, activities, issues, and interactions. Admin Chg 1 dated 3-12-13.

2011-02-23T23:59:59.000Z

457

Environmental Services Standard Tasks  

E-Print Network [OSTI]

1 Environmental Services Operations Standard Tasks The primary function of Environmental Services developed and implemented standard custodial tasks that meet industry standards. The standards are as follows: Exterior Building Cleaning Daily Clean ash urns Clean entry area glass Clean steps and remove

458

Economic analysis of proposed voluntary energy conservation standard for new residential buildings  

SciTech Connect (OSTI)

The objective of this document is to present an analysis of the impacts of the proposed voluntary energy conservation standard for the construction of new residential buildings. This analysis examines the impacts of having the proposed residential standard apply immediately and, alternatively, having the proposed standard phased in over a five-year period. It does not address the question of whether realistically the standard would be adopted by states, nor does it weight the improbable impact of states with higher energy efficiency standards modifying their standard to comply with this voluntary standard. 19 refs., 1 fig., 12 tabs.

Marsh, S.J.; Roop, J.M.; Callaway, J.W.; Taylor, Z.T.

1989-06-01T23:59:59.000Z

459

Understanding Building Energy Codes and Standards  

SciTech Connect (OSTI)

Energy codes and standards play a vital role by setting minimum requirements for energy-efficient design and construction. They outline uniform requirements for new buildings as well as additions and renovations. The Difference Between Energy Codes, Energy Standards and the Model Energy Code Energy codes--specify how buildings must be constructed or perform, and are written in mandatory, enforceable language. States or local governments adopt and enforce energy codes for their jurisdictions. Energy standards--describe how buildings should be constructed to save energy cost-effectively. They are published by national organizations such as the American Society of Heating, Refrigerating, and Air-Conditioning Engineers (ASHRAE). They are not mandatory, but serve as national recommendations, with some variation for regional climate. States and local governments frequently use energy standards as the technical basis for developing their energy codes. Some energy standards are written in mandatory, enforceable language, making it easy for jurisdictions to incorporate the provisions of the energy standards directly into their laws or regulations.

Bartlett, Rosemarie; Halverson, Mark A.; Shankle, Diana L.

2003-03-01T23:59:59.000Z

460

Effects of a carbon tax on combined heat and power adoption by a microgrid  

E-Print Network [OSTI]

of a Carbon Tax on Combined Heat and Power Adoption by aof a Carbon Tax on Combined Heat and Power Adoption by ainvolving combined heat and power (CHP). The expectation

Marnay, Chris; Edwards, Jennifer L.; Firestone, Ryan M.; Ghosh, Srijay; Siddidqui, Afzal S.; Stadler, Michael

2002-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "adopted interconnection standards" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


461

DOE Awards $12 Million to Spur Rapid Adoption of Solar Energy...  

Office of Environmental Management (EM)

DOE Awards 12 Million to Spur Rapid Adoption of Solar Energy with the Rooftop Solar Challenge DOE Awards 12 Million to Spur Rapid Adoption of Solar Energy with the Rooftop Solar...

462

Can Sustainable Transport Policies Cause Companies to Adopt Responsible Behaviour? Can Sustainable Transport  

E-Print Network [OSTI]

Can Sustainable Transport Policies Cause Companies to Adopt Responsible Behaviour? 221 Can Sustainable Transport Policies Cause Companies to Adopt Responsible Behaviour ? The case of the textile, transport policies have gradually set sustainable development targets. Although the objectives have evolved

Boyer, Edmond

463

E-Print Network 3.0 - all-hazards network adopted Sample Search...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

e ect. Indirect network e ects can arise even where|in a sense|nuisance adopters are common. A new... may encourage C to adopt, and A may want to interact ... Source:...

464

Interconnection Guidelines  

Broader source: Energy.gov [DOE]

In April 2001, Arkansas enacted legislation directing the Arkansas Public Service Commission (PSC) to establish net-metering rules for certain renewable-energy systems. The Arkansas Public Service...

465

Interconnection Guidelines  

Broader source: Energy.gov [DOE]

Missouri enacted legislation (S.B. 54) in June 2007 requiring all of the state's electric utilities -- including municipal utilities and electric cooperatives -- to offer net metering to customers...

466

Interconnection Guidelines  

Broader source: Energy.gov [DOE]

'''''Note: Delaware law ([http://delcode.delaware.gov/title26/c010/index.shtml#1014 26 Del. C. ß 1014]) requires the Delaware Public Service Commission (PSC), Delaware Electric Cooperative (DEC),...

467

Interconnection Guidelines  

Broader source: Energy.gov [DOE]

The Georgia Cogeneration and Distributed Generation Act of 2001 allows residential electricity customers with photovoltaic (PV) systems, wind-energy systems or fuel cells up to 10 kilowatts (kW) in...

468

Interconnection Guidelines  

Broader source: Energy.gov [DOE]

'''''Note: Ongoing proceedings related to net metering can be found in [http://lpscstar.louisiana.gov/star/portal/lpsc/page/Dockets/portal.aspx Docket R-31417.]'''''...

469

Hopper Interconnect  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May JunDatastreamsmmcrcalgovInstrumentsruc DocumentationP-SeriesFlickr FlickrGuidedCH2MLLC HistoryVeterans | NationalFile Storage

470

Energy and Economic Impacts of U.S. Federal Energy and Water Conservation Standards Adopted From 1987 Through 2011  

E-Print Network [OSTI]

for the global Social Cost of Carbon (SCC) developed by aOutlook 2011. The social cost of carbon (SCC) values from

Meyers, Stephen

2013-01-01T23:59:59.000Z

471

Energy and Economic Impacts of U.S. Federal Energy and Water Conservation Standards Adopted From 1987 through 2012  

E-Print Network [OSTI]

for the global Social Cost of Carbon (SCC) developed by athe 2035 factor. The social cost of carbon (SCC) values from

Meyers, Stephen

2013-01-01T23:59:59.000Z

472

Energy and Economic Impacts of U.S. Federal Energy and Water Conservation Standards Adopted From 1987 Through 2013  

E-Print Network [OSTI]

for the global Social Cost of Carbon (SCC) developed by aTechnical Update of the Social Cost of Carbon for RegulatoryWorking Group on Social Cost of Carbon, United States

, Stephen Meyers

2014-01-01T23:59:59.000Z

473

Energy and Economic Impacts of U.S. Federal Energy and Water Conservation Standards Adopted From 1987 through 2012  

E-Print Network [OSTI]

for electric motors. The base-case efficiency is estimatedefficiency and contractor cost for each product. Electric motors

Meyers, Stephen

2013-01-01T23:59:59.000Z

474

Energy and Economic Impacts of U.S. Federal Energy and Water Conservation Standards Adopted From 1987 Through 2010  

E-Print Network [OSTI]

for electric motors. The base-case efficiency is estimatedefficiency and contractor cost for each product. Electric motors

Meyers, Stephen

2013-01-01T23:59:59.000Z

475

Energy and Economic Impacts of U.S. Federal Energy and Water Conservation Standards Adopted From 1987 Through 2011  

E-Print Network [OSTI]

for electric motors. The base-case efficiency is estimatedefficiency and contractor cost for each product. Electric motors

Meyers, Stephen

2013-01-01T23:59:59.000Z

476

Energy and Economic Impacts of U.S. Federal Energy and Water Conservation Standards Adopted From 1987 Through 2011  

E-Print Network [OSTI]

Efficiency and Renewable Energy, Building TechnologiesEfficiency and Renewable Energy, Building Technologies

Meyers, Stephen

2013-01-01T23:59:59.000Z

477

Energy and Economic Impacts of U.S. Federal Energy and Water Conservation Standards Adopted From 1987 through 2012  

E-Print Network [OSTI]

Efficiency and Renewable Energy, Building TechnologiesEfficiency and Renewable Energy, Building Technologies

Meyers, Stephen

2013-01-01T23:59:59.000Z

478

Energy and Economic Impacts of U.S. Federal Energy and Water Conservation Standards Adopted From 1987 Through 2010  

E-Print Network [OSTI]

Efficiency and Renewable Energy, Building TechnologiesEfficiency and Renewable Energy, Building Technologies

Meyers, Stephen

2013-01-01T23:59:59.000Z

479

Energy and Economic Impacts of U.S. Federal Energy and Water Conservation Standards Adopted From 1987 through 2012  

E-Print Network [OSTI]

Refrigerator-Freezers .Refrigerators and Refrigerator-Freezers NAECA 1987 Freezers2005 Refrigerators, Refrigerator-Freezers and Freezers 2010,

Meyers, Stephen

2013-01-01T23:59:59.000Z

480

Energy and Economic Impacts of U.S. Federal Energy and Water Conservation Standards Adopted From 1987 Through 2010  

E-Print Network [OSTI]

Refrigerators and Refrigerator-Freezers NAECA 1987 Freezers2005 Refrigerators, Refrigerator-Freezers and Freezers 2010,in this case refrigerator-freezers. The average new

Meyers, Stephen

2013-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "adopted interconnection standards" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


481

Potential Impact of Adopting Maximum Technologies as Minimum Efficiency Performance Standards in the U.S. Residential Sector  

E-Print Network [OSTI]

Refrigerators, Refrigerator-Freezers, Freezers PreliminaryRefrigerators, Refrigerator-Freezers, Freezers Pre-NOPRlighting, television, refrigerator-freezers, central air

Letschert, Virginie

2010-01-01T23:59:59.000Z

482

Energy and Economic Impacts of U.S. Federal Energy and Water Conservation Standards Adopted From 1987 Through 2010  

E-Print Network [OSTI]

Commercial furnaces and boilers, air conditioners and heat pumps, and water heatersCOMMERCIAL & INDUSTRIAL EPACT 1992 Electric Motors EPACT 1992 Warm Air Furnaces EPACT 1992 Packaged Boilers EPACT 1992 Air Conditioners and Heat Pumps EPACT 1992 Water Heaters,

Meyers, Stephen

2013-01-01T23:59:59.000Z

483

Energy and Economic Impacts of U.S. Federal Energy and Water Conservation Standards Adopted From 1987 through 2012  

E-Print Network [OSTI]

Commercial furnaces and boilers, air conditioners and heat pumps, and water heatersCOMMERCIAL & INDUSTRIAL EPACT 1992 Electric Motors EPACT 1992 Warm Air Furnaces EPACT 1992 Packaged Boilers EPACT 1992 Air Conditioners and Heat Pumps EPACT 1992 Water Heaters,

Meyers, Stephen

2013-01-01T23:59:59.000Z

484

Energy and Economic Impacts of U.S. Federal Energy and Water Conservation Standards Adopted From 1987 Through 2011  

E-Print Network [OSTI]

Commercial furnaces and boilers, air conditioners and heat pumps, and water heatersCOMMERCIAL & INDUSTRIAL EPACT 1992 Electric Motors EPACT 1992 Warm Air Furnaces EPACT 1992 Packaged Boilers EPACT 1992 Air Conditioners and Heat Pumps EPACT 1992 Water Heaters,

Meyers, Stephen

2013-01-01T23:59:59.000Z

485

Energy and Economic Impacts of U.S. Federal Energy and Water Conservation Standards Adopted From 1987 Through 2013  

E-Print Network [OSTI]

Commercial furnaces and boilers, air conditioners and heat pumps, and water heatersCOMMERCIAL & INDUSTRIAL EPACT 1992 Electric Motors EPACT 1992 Warm Air Furnaces EPACT 1992 Packaged Boilers EPACT 1992 Air Conditioners and Heat Pumps EPACT 1992 Water Heaters,

, Stephen Meyers

2014-01-01T23:59:59.000Z

486

Energy and Economic Impacts of U.S. Federal Energy and Water Conservation Standards Adopted From 1987 Through 2011  

E-Print Network [OSTI]

Fluorescent Lamps and Incandescent Reflector Lamps EPACTBallasts and Fixtures General Service Incandescent Lamps,Intermediate Base Incandescent Lamps and Candelabra Base

Meyers, Stephen

2013-01-01T23:59:59.000Z

487

Energy and Economic Impacts of U.S. Federal Energy and Water Conservation Standards Adopted From 1987 through 2012  

E-Print Network [OSTI]

Fluorescent Lamps and Incandescent Reflector Lamps EPACTBallasts and Fixtures General Service Incandescent Lamps,Intermediate Base Incandescent Lamps and Candelabra Base

Meyers, Stephen

2013-01-01T23:59:59.000Z

488

Potential Impact of Adopting Maximum Technologies as Minimum Efficiency Performance Standards in the U.S. Residential Sector  

E-Print Network [OSTI]

and general lighting incandescent services (GLIS) areLighting Phase out of incandescent lighting has been passedout of general service incandescent lamps (GSIL) which donít

Letschert, Virginie

2010-01-01T23:59:59.000Z

489

Energy and Economic Impacts of U.S. Federal Energy and Water Conservation Standards Adopted From 1987 Through 2010  

E-Print Network [OSTI]

Fluorescent Lamps and Incandescent Reflector Lamps MediumBallasts and Fixtures General Service Incandescent Lamps,Intermediate Base Incandescent Lamps and Candelabra Base

Meyers, Stephen

2013-01-01T23:59:59.000Z

490

Energy and Economic Impacts of U.S. Federal Energy and Water Conservation Standards Adopted From 1987 through 2012  

E-Print Network [OSTI]

primary energy conversion factors. These factors representannual site- to-source conversion factors based on a versionsite-to- source conversion factors and are likely more

Meyers, Stephen

2013-01-01T23:59:59.000Z

491

Energy and Economic Impacts of U.S. Federal Energy and Water Conservation Standards Adopted From 1987 Through 2011  

E-Print Network [OSTI]

and Heat Pumps NAECA 1987 Water Heaters NAECA 1987 FurnacesPumps EPACT 1992 Water Heaters, Hot Water Supply Boilers andand heat pumps, and water heaters We modified the analytical

Meyers, Stephen

2013-01-01T23:59:59.000Z

492

Potential Impact of Adopting Maximum Technologies as Minimum Efficiency Performance Standards in the U.S. Residential Sector  

E-Print Network [OSTI]

central air conditioners, water heaters and furnaces) areair conditioners, water heaters and furnaces) UnregulatedM i l l o 10 i n s 2. Water Heaters DOE has issued a final

Letschert, Virginie

2010-01-01T23:59:59.000Z

493

Potential Impact of Adopting Maximum Technologies as Minimum Efficiency Performance Standards in the U.S. Residential Sector  

E-Print Network [OSTI]

2010). We consider only the BAT for storage water heaters.Shipments for gas storage water heaters are projected toyear while electric storage water heaters are projected to

Letschert, Virginie

2010-01-01T23:59:59.000Z

494

Energy and Economic Impacts of U.S. Federal Energy and Water Conservation Standards Adopted From 1987 Through 2013  

E-Print Network [OSTI]

are based on EIAís Annual Energy Outlook 2013. We convertedoutputs in EIAís Annual Energy Outlook 2012. The values

, Stephen Meyers

2014-01-01T23:59:59.000Z

495

Potential Impact of Adopting Maximum Technologies as Minimum Efficiency Performance Standards in the U.S. Residential Sector  

E-Print Network [OSTI]

Administration, Annual Energy Outlook 2010 with Projectionsis taken from the annual energy outlook (AEO) 2010 (DOE/EIA-

Letschert, Virginie

2010-01-01T23:59:59.000Z

496

Energy and Economic Impacts of U.S. Federal Energy and Water Conservation Standards Adopted From 1987 Through 2011  

E-Print Network [OSTI]

conditioners and heat pumps, and water heaters We modifiedConditioners and Heat Pumps NAECA 1987 Water Heaters NAECAConditioners and Heat Pumps EPACT 1992 Water Heaters, Hot

Meyers, Stephen

2013-01-01T23:59:59.000Z

497

Energy and Economic Impacts of U.S. Federal Energy and Water Conservation Standards Adopted From 1987 Through 2010  

E-Print Network [OSTI]

conditioners and heat pumps, and water heaters We modifiedConditioning Heat Pumps NAECA 1987 Water Heaters NAECA 1987Conditioners and Heat Pumps EPACT 1992 Water Heaters, Hot

Meyers, Stephen

2013-01-01T23:59:59.000Z

498

Energy and Economic Impacts of U.S. Federal Energy and Water Conservation Standards Adopted From 1987 through 2012  

E-Print Network [OSTI]

conditioners and heat pumps, and water heaters We modifiedConditioners and Heat Pumps NAECA 1987 Water Heaters NAECAConditioners and Heat Pumps EPACT 1992 Water Heaters, Hot

Meyers, Stephen

2013-01-01T23:59:59.000Z

499

Paru dans Prenatal Diagnosis, 1998, 18 :437-445. ADOPTION AND FOSTERING OF BABIES  

E-Print Network [OSTI]

noticed an increase in newborns with Down syndrome being placed up for adoption. The aim of this study : Down syndrome, human adoption, foster care inserm-00354600,version1-20Jan2009 #12;3 INTRODUCTION Until for adoption, showed that 12% had Down syndrome (DS). These babies represent 25.9% of total babies with DS

500

Pathways to Technology Transfer and Adoption: Achievements and Challenges (Mini-Tutorial)  

E-Print Network [OSTI]

Pathways to Technology Transfer and Adoption: Achievements and Challenges (Mini-Tutorial) Dongmei. There are some common challenges faced when pursuing technology transfer and adoption while particular challenges transfer and adoption. This mini-tutorial presents achievements and challenges of technology transfer

Xie, Tao