National Library of Energy BETA

Sample records for 600 500 400

  1. Corrosion of high temperature alloys in solar salt at 400, 500, and 680%C2%B0C.

    SciTech Connect (OSTI)

    Kruizenga, Alan Michael; Gill, David Dennis; LaFord, Marianne Elizabeth

    2013-09-01

    Corrosion tests at 400, 500, and 680%C2%B0C were performed using four high temperature alloys; 347SS, 321SS In625, and HA230. Molten salt chemistry was monitored over time through analysis of nitrite, carbonate, and dissolved metals. Metallography was performed on alloys at 500 and 680%C2%B0C, due to the relatively thin oxide scale observed at 400%C2%B0C. At 500%C2%B0C, corrosion of iron based alloys took the form of chromium depletion and iron oxides, while nickel based alloys also had chromium depletion and formation of NiO. Chromium was detected in relatively low concentrations at this temperature. At 680%C2%B0C, significant surface corrosion occurred with metal losses greater than 450microns/year after 1025hours of exposure. Iron based alloys formed complex iron, sodium, and chromium oxides. Some data suggests grain boundary chromium depletion of 321SS. Nickel alloys formed NiO and metallic nickel corrosion morphologies, with HA230 displaying significant internal oxidation in the form of chromia. Nickel alloys both exhibited worse corrosion than iron based alloys likely due to preferential dissolution of chromium, molybdenum, and tungsten.

  2. Irradiation Creep and Swelling from 400 C to 600 C of the Oxide Dispersion Strengthened Ferritic Alloy MA957

    SciTech Connect (OSTI)

    Toloczko, Mychailo B.; Gelles, David S.; Garner, Francis A.; Kurtz, Richard J.; Abe, Katsunori

    2004-04-24

    Recently, there has been a growing interest in the use of oxide dispersion strengthened (ODS) ferritic steels for fusion reactor applications. As part of an extensive study performed at PNNL on the ODS steel MA957 [1], irradiation creep tests were performed on pressurized tubes made from MA957 by two different methods. The tubes were made either by gun drilling alone or by a combination of rod drawing and gun drilling. The different fabrication methods were explored because ODS steels have been difficult to form. The pressurized tubes were irradiated in the Fast Flux Test Facility (FFTF) to doses ranging from 40 dpa to 110 dpa at temperatures ranging from 400 C to 600 C. The effective stresses resulting from the pressurization of the tubes ranged from 0 MPa to 175 MPa.

  3. C-H surface diamond field effect transistors for high temperature (400 °C) and high voltage (500 V) operation

    SciTech Connect (OSTI)

    Kawarada, H.; Tsuboi, H.; Naruo, T.; Yamada, T.; Xu, D.; Daicho, A.; Saito, T.; Hiraiwa, A.

    2014-07-07

    By forming a highly stable Al{sub 2}O{sub 3} gate oxide on a C-H bonded channel of diamond, high-temperature, and high-voltage metal-oxide-semiconductor field-effect transistor (MOSFET) has been realized. From room temperature to 400 °C (673 K), the variation of maximum drain-current is within 30% at a given gate bias. The maximum breakdown voltage (V{sub B}) of the MOSFET without a field plate is 600 V at a gate-drain distance (L{sub GD}) of 7 μm. We fabricated some MOSFETs for which V{sub B}/L{sub GD} > 100 V/μm. These values are comparable to those of lateral SiC or GaN FETs. The Al{sub 2}O{sub 3} was deposited on the C-H surface by atomic layer deposition (ALD) at 450 °C using H{sub 2}O as an oxidant. The ALD at relatively high temperature results in stable p-type conduction and FET operation at 400 °C in vacuum. The drain current density and transconductance normalized by the gate width are almost constant from room temperature to 400 °C in vacuum and are about 10 times higher than those of boron-doped diamond FETs.

  4. Design and Construction of a 500 KW CW, 400 MHZ Klystron To Be Used As RF Power Source For LHC/RF Component Tests

    SciTech Connect (OSTI)

    Pearson, Chris

    2003-05-05

    A 500 kW cw klystron operating at 400 MHz was developed and constructed jointly by CERN and SLAC for use as a high-power source at CERN for testing LHC/RF components such as circulators, RF absorbers and superconducting cavities with their input couplers. The design is a modification of the 353 MHz SLAC PEP-I klystron. More than 80% of the original PEP-I tube parts could thus be incorporated in the LHC test klystron which resulted in lower engineering costs as well as reduced development and construction time. The physical length between cathode plane and upper pole plate was kept unchanged so that a PEP-I tube focusing solenoid, available at CERN, could be re-used. With the aid of the klystron simulation codes JPNDISK and CONDOR, the design of the LHC tube was accomplished, which resulted in a tube with noticeably higher efficiency than its predecessor, the PEP-I klystron. The integrated cavities were redesigned using SUPERFISH and the output coupling circuit, which also required redesigning, was done with the aid of MAFIA. Details of the tube development and test results are presented.

  5. Results of U-xMo (x=7, 10, 12 wt.%) Alloy versus Al-6061 Cladding Diffusion Couple Experiments Performed at 500, 550 and 600 Degrees C

    SciTech Connect (OSTI)

    Emmanuel Perez; Dennis D. Keiser, Jr.; Yongho Sohn

    2013-04-01

    The Reduced Enrichment for Research and Test Reactors (RERTR) program has been developing low enrichment fuel systems encased in Al 6061 for use in research and test reactors. U–Mo alloys in contact with Al and Al alloys can undergo diffusional interactions that can result in the development of interdiffusion zones with complex fine-grained microstructures composed of multiple phases. A monolithic fuel currently being developed by the RERTR program has local regions where the U–Mo fuel plate is in contact with the Al 6061 cladding and, as a result, the program finds information about interdiffusion zone development at high temperatures of interest. In this study, the microstructural development of diffusion couples consisting of U-7wt.%Mo, U-10wt.%Mo, and U-12wt.%Mo vs. Al 6061 (or 6061 aluminum) cladding, annealed at 500, 550, 600 degrees C for 1, 5, 20, 24, or 132 hours, was analyzed by backscatter electron microscopy and x-ray energy dispersive spectroscopy on a scanning electron microscope. Concentration profiles were determined by standardized wavelength dispersive spectroscopy and standardless x-ray energy dispersive spectroscopy. The results of this work shows that the presence of surface layers at the U–Mo/Al 6061 interface can dramatically impact the overall interdiffusion behavior in terms of rate of interaction and uniformity of the developed interdiffusion zones. It further reveals that relatively uniform interaction layers with higher Si concentrations can develop in U–Mo/Al 6061 couples annealed at shorter times and that longer times at temperature result in the development of more non-uniform interaction layers with more areas that are enriched in Al. At longer annealing times and relatively high temperatures, U–Mo/Al 6061 couples can exhibit more interaction compared to U–Mo/pure Al couples. The minor alloying constituents in Al 6061 cladding can result in the development of many complex phases in the interaction layer of U

  6. Oxford System 400

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Oxford Plasmalab System 400 Sputtering System For questions concerning this machines capabilities, please contact Varshni Singh, at 578-0248. ecr.jpg (48456 bytes)  : ecr1.jpg...

  7. K500 - Facilities - Cyclotron Institute

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    K500 Superconducting Cyclotron The K500 Cyclotron with its upper steel pole cap raised for ... miles) of niobium-titanium superconducting wire in a coil surrounded by 100 tons of steel. ...

  8. File:600.pdf | Open Energy Information

    Open Energy Info (EERE)

    600.pdf Jump to: navigation, search File File history File usage File:600.pdf Size of this preview: 463 599 pixels. Other resolution: 464 600 pixels. Go to page 1 2 3 4 5 6 7...

  9. President Obama Announces $400 Million Conditional Commitment...

    Energy Savers [EERE]

    announced the offer of a conditional commitment for a loan guarantee of 400 million to Abound Solar Manufacturing, LLC to manufacture state-of-the-art thin-film solar panels. ...

  10. Edgestar: ENERGY STAR Referral (DEP400EW)

    Broader source: Energy.gov [DOE]

    DOE referred the matter of Edgestar-brand dehumidifier, model DEP400EW, to the EPA for appropriate action after DOE testing showed that the model does not meet the ENERGY STAR specification.

  11. Crashworthiness of the AT-400A shipping container

    SciTech Connect (OSTI)

    Gruda, J.D.; York, A.R. II

    1996-05-01

    Shipping containers used for transporting radioactive material must be certified using federal regulations. These regulations require the container be tested or evaluated in severe mechanical and thermal environments which represent hypothetical accident scenarios. The containers are certified if the inner container remains leaktight. This paper presents results from finite element simulations of the accidents which include subjecting the AT-400A (for Pu from dismantled nuclear weapons) to a 30-foot (9 m) drop onto an unyielding target and crushing the container with an 1100 lb (500 kg) steel plate dropped from 30 feet. The nonlinear PRONTO3D finite element results were validated using test results. The simulations of the various impacts and crushes identified trends and worst-case orientations. They also showed that there is a significant margin of safety based on the failure of the containment vessel.

  12. Coming: 12,600 megawatts at Itaipu Island

    SciTech Connect (OSTI)

    de Moraes, J.

    1983-08-01

    This paper describes the hydroelectric plant being constructed jointly by Brazil and Paraguay on Itaipu Island in the Parana River. The planned generating capacity of 12,600 MW will make the Itaipu plant the world's largest. It will employ the most powerful hydrogenerators and turbines yet built, the world's largest concentration of 500-kilovolt gas-insulated switchgear, the highest dc transmission voltages and power--600 kV and 6300 MW--ever used, about 1000 kilometers of 765-kV ac transmission, and an extensive computer-based digital supervisory system in which continuous diagnostic evaluation of equipment is emphasized. To maintain national standards, nine generators will operate at 60 hertz for Brazil and nine at 50 hertz for Paraguay. Initially, any excess electricity available from the Paraguay generators will be routed to Brazil, but Paraguay is ultimately expected to share in half the Itaipu generation. The paper discusses the plant from its original feasibility studies to the newly created technologies which its size necessitated. The environmental impact on forests, farmlands and wildlife resulting from the construction of the Itaipu dam and the loss of the 1400 square kilometers which it flooded--including the popular Seven Waterfalls--is addressed. References to other papers as well as a symposium on the Itaipu project are cited.

  13. 500 kV Spare Transformer Procurement

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Procurement capital project is for the acquisition of five, 500 kV spare transformers, which are to be strategically located throughout the system, and for the...

  14. Westinghouse Offers $6,400 in College Scholarships to Eddy County Students

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Offers $6,400 in College Scholarships to Eddy County Students CARLSBAD, N.M., February 18, 2000 - The Westinghouse Government Services Group today announced that $6,400 in college scholarships will be awarded to Eddy County students for the 2000-2001 school year. The deadline to apply is April 3. Two $2,500 scholarships are being offered - one will be honored at New Mexico State University (NMSU) in Las Cruces, and one at the College of the Southwest (CSW) in Carlsbad. High school seniors

  15. Stress corrosion cracking of Alloy 600. [PWR

    SciTech Connect (OSTI)

    Serra, E.

    1981-11-01

    The stress corrosion cracking of Alloy 600 tubing has affected the performance of several pressurized water reactor steam generators. The purpose of this report is to summarize the research which has followed that reviewed by D. van Rooyen in 1975. Although several papers and reports have been published there still is not a general model that can explain the stress corrosion cracking behavior of Alloy 600 in deaerated or aerated high-temperature pure water or in the environments that might exist in the primary and secondary coolant of a steam generator. Such a model, if it exists, must cover the complex interaction of the environmental, metallurgical, and mechanical variables which control the susceptibility of Alloy 600 to stress corrosion cracking. Each of these classes of variables is discussed in the text.

  16. Welding the AT-400A Containment Vessel

    SciTech Connect (OSTI)

    Brandon, E.

    1998-11-01

    Early in 1994, the Department of Energy assigned Sandia National Laboratories the responsibility for designing and providing the welding system for the girth weld for the AT-400A containment vessel. (The AT-400A container is employed for the shipment and long-term storage of the nuclear weapon pits being returned from the nation's nuclear arsenal.) Mason Hanger Corporation's Pantex Plant was chosen to be the production facility. The project was successfully completed by providing and implementing a turnkey welding system and qualified welding procedure at the Pantex Plant. The welding system was transferred to Pantex and a pilot lot of 20 AT-400A containers with W48 pits was welded in August 1997. This document is intended to bring together the AT-400A welding system and product (girth weld) requirements and the activities conducted to meet those requirements. This document alone is not a complete compilation of the welding development activities but is meant to be a summary to be used with the applicable references.

  17. WIPP Receives 500th Waste Shipment

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    500 th Waste Shipment CARLSBAD, N.M., January 7, 2002 - The U.S. Department of Energy's (DOE) Waste Isolation Pilot Plant (WIPP) reached a new milestone Saturday with the safe arrival of its 500 th shipment of transuranic waste. The 500 th shipment arrived at WIPP at 6:38 p.m. Saturday from DOE's Rocky Flats Environmental Technology Site in Colorado. It was the 282 nd shipment to WIPP from Rocky Flats - one of five DOE sites sending defense-generated radioactive waste to WIPP for permanent

  18. TOP500 | National Nuclear Security Administration

    National Nuclear Security Administration (NNSA)

    TOP500 Two of the World's Most Powerful Computers work for NNSA Two NNSA supercomputers-Trinity and Sequoia-are among the top six systems in the world, according to the 46th edition of the twice-yearly TOP500 list of the most powerful supercomputers released this month. Sequoia has been the world's third most powerful computer since June 2013, while Trinity is

  19. Influence of product type on stress corrosion cracking of alloy 600

    SciTech Connect (OSTI)

    Gomez-Briceno, D.; Blazquez, F.; Hernandez, F.

    1999-03-01

    Grain-boundary carbide coverage obtained from metallographic replications has been considered as an estimation of SCC susceptibility of alloy 600 components in pressurized-water reactor (PWR) primary water. Stress corrosion cracking (SCC) initiation tests were carried out on alloy 600 (UNS N06600) in primary water at 325 C and 360 C and in steam with hydrogen at 400 C to gain some insight into the SCC behavior of different alloy 600 products. Forged bars, thick-walled tubes (cold-worked and hot-worked), and steam generator (SG) tubing with different thermomechanical histories were tested. As expected, materials with a high density of intergranular carbide were more resistant to cracking in high-temperature water than materials with few carbides in the grain boundary. However, materials with similar microstructures but different thermomechanical histories presented different SCC susceptibilities. In general, forged bars were more resistant than thick-walled materials with similar grain-boundary carbide coverage. Cold-worked materials (thick-walled tubes and SG tubing) presented similar behaviors. However, appearance of intergranular fractures at high magnification seemed to be related to the SCC behavior of alloy 600 in steam and in primary water. More resistant materials exhibited pseudointergranular fractures.

  20. TOP500 Supercomputers for June 2002

    SciTech Connect (OSTI)

    Strohmaier, Erich; Meuer, Hans W.; Dongarra, Jack; Simon, Horst D.

    2002-06-20

    19th Edition of TOP500 List of World's Fastest Supercomputers Released MANNHEIM, Germany; KNOXVILLE, Tenn.;&BERKELEY, Calif. In what has become a much-anticipated event in the world of high-performance computing, the 19th edition of the TOP500 list of the worlds fastest supercomputers was released today (June 20, 2002). The recently installed Earth Simulator supercomputer at the Earth Simulator Center in Yokohama, Japan, is as expected the clear new number 1. Its performance of 35.86 Tflop/s (trillions of calculations per second) running the Linpack benchmark is almost five times higher than the performance of the now No.2 IBM ASCI White system at Lawrence Livermore National Laboratory (7.2 Tflop/s). This powerful leap frogging to the top by a system so much faster than the previous top system is unparalleled in the history of the TOP500.

  1. TOP500 Supercomputers for November 2003

    SciTech Connect (OSTI)

    Strohmaier, Erich; Meuer, Hans W.; Dongarra, Jack; Simon, Horst D.

    2003-11-16

    22nd Edition of TOP500 List of World s Fastest Supercomputers Released MANNHEIM, Germany; KNOXVILLE, Tenn.; BERKELEY, Calif. In what has become a much-anticipated event in the world of high-performance computing, the 22nd edition of the TOP500 list of the worlds fastest supercomputers was released today (November 16, 2003). The Earth Simulator supercomputer retains the number one position with its Linpack benchmark performance of 35.86 Tflop/s (''teraflops'' or trillions of calculations per second). It was built by NEC and installed last year at the Earth Simulator Center in Yokohama, Japan.

  2. A High Temperature (400 to 650oC) Secondary Storage Battery Based on Liquid Sodium and Potassium Anodes

    SciTech Connect (OSTI)

    Tao, Greg; Weber, Neill

    2007-06-08

    This STTR Phase I research program was on the development of high temperature (400 to 650 C), secondary batteries with roundtrip efficiency > 90% for integration with a 3 to 10 kW solid oxide fuel cell (SOFC) system. In fulfillment of this objective, advanced planar high temperature rechargeable batteries, comprised of an alkali metal ion conducting, highly refractory, beta'' alumina solid electrolyte (BASE) sandwiched between liquid sodium (or potassium) anode and liquid metal salt cathode, were developed at MSRI. The batteries have been successfully demonstrated at a working temperature as high as 600 C. To our knowledge, so far no work has been reported in the literature on planar rechargeable batteries based on BASE, and results obtained in Phase I for the very first time demonstrated the viability of planar batteries, though relatively low temperature tubular-based sodium-sulfur batteries and ZEBRA batteries have been actively developed by very limited non U.S. companies. The results of this Phase I work have fulfilled all the goals and stated objectives, and the achievements showed much promise for further, substantial improvements in battery design and performance. The important results of Phase I are briefly described in what follows: (1) Both Na-BASE and K-BASE discs and tubes have been successfully fabricated using MSRI's patented vapor phase process. Ionic conductivity measurements showed that Na-BASE had higher ionic conductivity than K-BASE, consistence with the literature. At 500 C, Na-BASE conductivity is 0.36 S/cm, which is more than 20 times higher than 8YSZ electrolyte used for SOFC at 800 C. The activation energy is 22.58 kJ/mol. (2) CuCl{sub 2}, FeCl{sub 2}, ZnCl{sub 2}, and AgCl were identified as suitable salts for Na/metal salt or K/metal salt electrochemical couples based on thermochemical data. Further open circuit voltage measurements matched those deduced from the thermochemical data. (3) Tubular cells with CuCl{sub 2} as the cathode and

  3. AP600 containment purge radiological analysis

    SciTech Connect (OSTI)

    O`Connor, M.; Schulz, J.; Tan, C.

    1995-02-01

    The AP600 Project is a passive pressurized water reactor power plant which is part of the Design Certification and First-of-a-Kind Engineering effort under the Advanced Light Water Reactor program. Included in this process is the design of the containment air filtration system which will be the subject of this paper. We will compare the practice used by previous plants with the AP600 approach to meet the goals of industry standards in sizing the containment air filtration system. The radiological aspects of design are of primary significance and will be the focus of this paper. The AP600 Project optimized the design to combine the functions of the high volumetric flow rate, low volumetric flow rate, and containment cleanup and other filtration systems into one multi-functional system. This achieves a more simplified, standardized, and lower cost design. Studies were performed to determine the possible concentrations of radioactive material in the containment atmosphere and the effectiveness of the purge system to keep concentrations within 10CFR20 limits and within offsite dose objectives. The concentrations were determined for various reactor coolant system leakage rates and containment purge modes of operation. The resultant concentrations were used to determine the containment accessibility during various stages of normal plant operation including refueling. The results of the parametric studies indicate that a dual train purge system with a capacity of 4,000 cfm per train is more than adequate to control the airborne radioactivity levels inside containment during normal plant operation and refueling, and satisfies the goals of ANSI/ANS-56.6-1986 and limits the amount of radioactive material released to the environment per ANSI/ANS 59.2-1985 to provide a safe environment for plant personnel and offsite residents.

  4. Intergranular attack of Alloy 600: simulation tests

    SciTech Connect (OSTI)

    Daret, J.

    1985-06-01

    In some steam generators, intergranular attack (IGA) has been detected on Alloy 600 tubes within or near the tubesheet crevice region. In order to reproduce IGA in an experimental device, refreshed autoclave simulation tests were performed with caustic pollution or river water in-leakage. During three runs of three tests each, chemical parameter and test procedures were adjusted to finally obtain a representative corrosion attack of tubing within the tubesheet crevice for the case of a caustic pollution. IGA was not detected for the river water in-leakage case.

  5. Intergranular attack of alloy 600: laboratory investigations

    SciTech Connect (OSTI)

    Pinard-Legry, G.; Plante, G.

    1985-08-01

    In order to define some of the parameters of the IGA phenomenon, chemical and electrochemical corrosion tests were performed on alloy 600 C-ring samples in caustic media at high temperature. Metallographic examinations showed that temperature and the composition of the solution has a marked effect on the occurrence of IGA. In 36% caustic solution, silicate did not inhibit corrosion as was the case in more dilute solution. The presence of magnetite had an adverse effect probably because it changed the local chemistry. The electrochemical potential effect was not significant on IGA morphology in the range E/sub corr/ +- 20 mV. Tensile stress increased the rate of IGA but was not necessary in order to produce IGA in an already aggressive environment. The presence of oxides did not change the alloy 600 corrosion potential significantly, except for Cr/sub 2/O/sub 3/. Borate ions had an inhibiting effect on IGA in 10 % caustic. The addition of boric acid to 10 % caustic produced changes in pH at high temperatures which were measured as part of this report. 6 refs., 30 figs., 12 tabs.

  6. WAC 173-400 - General Regulations for Air Pollution Sources ...

    Open Energy Info (EERE)

    400 - General Regulations for Air Pollution Sources Jump to: navigation, search OpenEI Reference LibraryAdd to library Legal Document- RegulationRegulation: WAC 173-400 - General...

  7. WAC - 173-400 General Regulations for Air Pollution Sources ...

    Open Energy Info (EERE)

    400 General Regulations for Air Pollution Sources Jump to: navigation, search OpenEI Reference LibraryAdd to library Legal Document- RegulationRegulation: WAC - 173-400 General...

  8. Application for Presidential Permit OE Docket No. PP-400 TDI...

    Broader source: Energy.gov (indexed) [DOE]

    PP-400 TDI-NE - Response Letter from DOD.pdf (52 KB) More Documents & Publications Application for Presidential Permit OE Docket No. PP-400 TDI- NE New England Clean Power Link ...

  9. Microsoft Word - 500_FinalPaper.docx

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    th International Topical Meeting on Nuclear Reactor Thermalhydraulics, NURETH-14, Toronto, Ontario, Canada, September 25-30, 2011 NURETH-14-500 Reactor Core Sub-Assembly Simulations Using a Stabilized Finite Element Method T. M. Smith, J. N. Shadid, R. P. Pawlowski, E. C. Cyr, and P. D. Weber Sandia National Laboratories 1 Abstract This paper presents a methodology for solving thermal-hydraulic flows that are prototypical to nuclear reactors, using a stabilized finite element method. The

  10. Klamath Residence (500) Space Heating Low Temperature Geothermal...

    Open Energy Info (EERE)

    Residence (500) Space Heating Low Temperature Geothermal Facility Jump to: navigation, search Name Klamath Residence (500) Space Heating Low Temperature Geothermal Facility...

  11. Development of a 500 Watt High Temperature Thermoelectric Generator...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    a 500 Watt High Temperature Thermoelectric Generator Development of a 500 Watt High Temperature Thermoelectric Generator A low temperature TEG has been built and tested providing ...

  12. ESnet, NERSC Blaze 400G Production Network Path

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    ESnet, NERSC Blaze 400G Production Network Path ESnet, NERSC Blaze 400G Production Network Path 400G Link is First Ever by R&E Network November 10, 2015 Contact: Jon Bashor, jbashor@lbl.gov, 510-486-5849 NetworkMapIllustration.png This map shows the 400G production link between Wang Hall at the main LBNL site and the Oakland Scientific Facility. The Department of Energy's Energy Sciences Network (ESnet) and the National Energy Research Scientific Computing Center (NERSC) have built a 400

  13. AP600 design certification thermal hydraulics testing and analysis

    SciTech Connect (OSTI)

    Hochreiter, L.E.; Piplica, E.J.

    1995-09-01

    Westinghouse Electric Corporation, in conjunction with the Department of Energy and the Electric Power Research Institute, have been developing an advanced light water reactor design; the AP600. The AP600 is a 1940 Mwt, 600Mwe unit which is similar to a Westinghouse two-loop Pressurized Water Reactor. The accumulated knowledge on reactor design to reduce the capital costs, construction time, and the operational and maintenance cost of the unit once it begins to generate electrical power. The AP600 design goal is to maintain an overall cost advantage over fossil generated electrical power.

  14. President Obama Announces $400 Million Conditional Commitment Offer to

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Support Solar Panel Manufacturing | Department of Energy 400 Million Conditional Commitment Offer to Support Solar Panel Manufacturing President Obama Announces $400 Million Conditional Commitment Offer to Support Solar Panel Manufacturing July 3, 2010 - 12:00am Addthis Washington D.C. - In his weekly video address, President Obama today announced the offer of a conditional commitment for a loan guarantee of $400 million to Abound Solar Manufacturing, LLC to manufacture state-of-the-art

  15. Summary - Building C-400 Thermal Treatment Remedial Design Report...

    Office of Environmental Management (EM)

    C-400 Thermal Treatment 90% Remedial Design Report and Site Investigation, Paducah ... What the ETR Team Recommended The data provide an initial basis for designoperation; ...

  16. Application for Presidential Permit OE Docket No. PP-400 TDI...

    Broader source: Energy.gov (indexed) [DOE]

    Conservation Law Foundation (CLF) provides the following comments and Motion to Intervene regarding the Application by TDI-New England presidential permit. PP-400 TDI-NE - Motion ...

  17. NASCAR Green Gets First Place in Daytona 500 | Department of...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    A story about how fuel cell generators were used at the Daytona 500 is currently posted on the Energy Department's blog. Read NASCAR Green Gets First Place in Daytona 500 to learn ...

  18. Super-Stable, Highly Monodisperse Plasmonic Nanocrystals with 500 Gold Atoms: Au~500(SR)~120

    SciTech Connect (OSTI)

    Kumara, Chanaka; Zuo, Xiaobing; Ilavsky, Dr. Jan; Chapman, Karena; Cullen, David A; Dass, Amala

    2014-01-01

    Determining the composition of plasmonic nanoparticles is challenging due to a deficiency in tools capable of accurately evaluating the number of atoms. Mass spectrometry plays a significant role in determining nanoparticle composition at the atomic level. Significant progress has been made in understanding ultra-small gold nanoparticles, like Au25(SR)18 and Au38(SR)24, with a Au core diameter of 0.97 and 1.3 nm, respectively. However, progress in small plasmonic nanoparticles (2 - 5 nm) is currently challenging, due in part to limitations in synthesizing monodisperse nanoparticles. Here, we report a plasmonic nanocrystal that is highly monodisperse, with an unprecedented variation of less than 20 gold atoms. The composition of the super-stable plasmonic nanocrystals at 115 kDa was determined to contain Au500 10SR120 3. The Au~500 system, named Faraduarate-500, is the largest size to be characterized using high resolution ESI mass spectrometry. Atomic pair distribution function (PDF) data shows that the local atomic structure is consistent with a face-centered cubic (fcc) or Marks decahedral arrangement. High resolution scanning transmission electron microscopy images show that the diameter is 2.4 0.1 nm. The radius of gyration measured by small angle X-ray scattering (SAXS), is 1.05 0.05 nm, and the size and the shape of SAXS molecular envelope are in agreement with TEM and PDF measurements.

  19. Improvement of voltage holding capability in the 500 keV negative ion source for JT-60SA

    SciTech Connect (OSTI)

    Tanaka, Y.; Hanada, M.; Kojima, A.; Akino, N.; Shimizu, T.; Ohshima, K.; Inoue, T.; Watanabe, K.; Taniguchi, M.; Kashiwagi, M.; Umeda, N.; Tobari, H.; Grisham, L. R.; Collaboration: JT-60 NBI Group

    2010-02-15

    Voltage holding capability of JT-60 negative ion source that has a large electrostatic negative ion accelerator with 45 cmx1.1 m acceleration grids was experimentally examined and improved to realize 500 keV, 22 A, and 100 s D{sup -} ion beams for JT-60 Super Advanced. The gap lengths in the acceleration stages were extended to reduce electric fields in a gap between the large grids and at the corner of the support flanges from the original 4-5 to 3-4 kV/mm. As a result, the voltage holding capability without beam acceleration has been successfully improved from 400 to 500 kV. The pulse duration to hold 500 kV reached 40 s of the power supply limitation.

  20. Stress corrosion cracking of welded Alloy 600 penetration mockups

    SciTech Connect (OSTI)

    Sarver, J.M.; Pathania, R.S.; Stuckey, K.; Fyfitch, S.; Gelpi, A.; Foucault, M.; Hunt, E.S.

    1995-12-31

    The primary water stress corrosion cracking (PWSCC) of Alloy 600 in components other than steam generators is a problem of increasing concern for nuclear power plants. Of greatest concern at the present time is the PWSCC of Alloy 600 vessel head penetrations. The common elements of these components are threefold: (1) the Alloy 600 material has a susceptible microstructure, (2) the Alloy 600 material is either a thick-walled tube or a bar which has been machined into a thick-walled tube, and (3) the Alloy 600 material has been welded into a structure such that high residual welding stresses exist in the postwelded Alloy 600 material. The objectives of the present program were to evaluate the PWSCC behavior of various configurations of welded Alloy 600 penetrations, and possible remedial measures which would prevent or retard PWSCC in these components. Mockups were instrumented to permit instantaneous remote sensing of through-wall cracking and were autoclave tested along with control C-rings in a doped steam environment. Following the test exposures, the mockups were split and examined to characterize the cracking morphology and the material microstructure. A Weibull distribution was used to analyze the time-to-failure results, and the observed cracking locations were compared to residual stress levels predicted by an elastic-plastic finite element analysis of the mockups.

  1. The relationship between observed stress corrosion cracking fracture morphology and microstructure in Alloy 600

    SciTech Connect (OSTI)

    Symons, D.M.; Burke, M.G.; Foster, J.P.

    1997-12-31

    Microstructure is known to influence the stress corrosion cracking (SCC) behavior of Alloy 600 in both hydrogenated water and steam environments. This study evaluated the relative SCC response of a single heat of Alloy 600 as a function of microstructure in a hydrogenated doped-steam environment. The 400 C doped-steam environment was selected for the SCC tests to accelerate cracking. The material was evaluated in three conditions: (1) as-received (2) as-annealed, and (3) as-annealed + 26% deformation. Microstructural characterization was performed using analytical electron microscopy (AEM) techniques for the evaluation of carbide type and morphology, and general structure. Constant displacement (bolt-loaded) compact tension specimens were used to induce SCC. The as-annealed and as-annealed plus cold worked samples had two fracture morphologies: a rough intergranular SCC fracture morphology and a smooth intergranular fracture morphology. The SCC fracture in the as-received specimens was characterized by a classic intergranular morphology at low magnification, consistent with the microstructural evaluation of cross-sectional metallographic samples. More detailed examination revealed a pseudo-intergranular fracture morphology. This pseudo-intergranular morphology appears to be comprised of very fine cleavage-like microfacets. These observations may assist in understanding the difference in SCC fracture morphologies as reported in the open literature.

  2. ARRA Program Celebrates Milestone 600,000 Smart Meter Installations

    Broader source: Energy.gov [DOE]

    On April 11, 2012, DOE Recovery Act funding recipient Sacramento Municipal Utility District (SMUD) celebrated a major milestone in the development of a regional smart grid in California: the installation of over 600,000 smart meters.

  3. Conceptual designs for the AT-400MO package

    SciTech Connect (OSTI)

    Fischer, L.E.; Hafner, R.F.; Hovingh, J.; Keeton, S.C.; Russell, E.W.; Lemmings, J.

    1997-01-01

    Currently, Pantex handles and stores weapons pits in AT-400A packages. The Department of Energy currently plans to oversee the conversion of weapon pits into plutonium metal or oxide. These products will then be stored, and perhaps transported at a later time, to other DOE sites. If DOE assigns the pit conversion process to Pantex, it makes sense to store the resulting Pu metal or oxide at Pantex, utilizing existing facilities, equipment, processes, and personnel. The four conceptual designs presented herein substitute the current AT-400A containment vessel, designed for weapon pits, with a vessel designed to store and/or ship Pu metal or oxides. These new designs utilize the existing AT-400A overpack system consisting of the drum assembly and radial impact limiters and likewise employ existing AT-400A production operations.

  4. Obama Administration Announces Additional $20,117,400 for Local...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    ... Funding for state, city, and county governments in the state includes: AR Arkansas Total Sum City, County, and SEO Allocations All 20,117,400 AR Arkansas State Energy Office ...

  5. 400 Area/Fast Flux Test Facility - Hanford Site

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    325 Building 400 AreaFast Flux Test Facility 618-10 ... Test Facility D and DR Reactors Effluent Treatment ... (thermal) liquid-metal (sodium)-cooled nuclear research ...

  6. Application for Presidential Permit OE Docket No. PP-400 TDI...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    NE New England Clean Power Link Project Application for Presidential Permit OE Docket No. PP-400 TDI- NE New England Clean Power Link Project Response to TDI - NE application from ...

  7. Application for Presidential Permit OE Docket No. PP-400 TDI...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    New England - New England Clean Power Link Project Application for Presidential Permit OE Docket No. PP-400 TDI-New England - New England Clean Power Link Project Application from ...

  8. Application for Presidential Permit OE Docket No. PP-400 TDI...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    - New England Clean Power Link Project: Federal Register Notice, Volume 79, No. 131 - July 9, 2014 Application for Presidential Permit OE Docket No. PP-400 TDI-NE - New England ...

  9. Department of Energy Closes $400 Million Loan Guarantee for State...

    Broader source: Energy.gov (indexed) [DOE]

    Steven Chu announced today that a 400 million loan guarantee has been finalized for Abound Solar Manufacturing, LLC to manufacture state-of-the-art thin-film solar panels. ...

  10. ESnet, NERSC Blaze 400G Production Network Path

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    to act as a single 400 Gbps optical transport connection between the two sites. A History of Strong Connections The user facilities known today as NERSC and ESnet both date...

  11. Comparative study of the embrittlement of Monel 400 at room temperature by hydrogen and by mercury

    SciTech Connect (OSTI)

    Price, C.E.; Fredell, R.S.

    1986-05-01

    Slow strain rate tensile tests were performed at room temperature on Monel 400 specimens of grain sizes 35 to 500 microns, in the environments of air, mercury, and electrolytically generated hydrogen. Specimens of grain size 250 microns were tested at a range of strain rates in the three environments. It was found that cracks initiated easiest in hydrogen but propagated easiest in mercury; consequently the embrittlement was usually more severe in mercury. The embrittlement decreased with increasing strain rate, and with increasing grain size in hydrogen. Embrittlement in mercury was maximum at intermediate grain sizes. A fracture sequence of intergranular to transgranular to microvoid coalescence was common. The intergranular and transgranular fractures are interpreted in terms of the reduced cohesive stress and enhanced shear models of embrittlement, respectively. 52 references.

  12. Geothermal Data Repository Reaches 500 Submissions | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Data Repository Reaches 500 Submissions Geothermal Data Repository Reaches 500 Submissions August 25, 2015 - 2:41pm Addthis Geothermal Data Repository Reaches 500 Submissions Arlene Anderson Technology Development Manager, Geothermal Technologies Program A map of the United States highlighting the locations of GDR users. Critical data about the subsurface is added to the GDR from sites all across the country. Credit: Jon Weers, NREL. July 15 marked an important milestone for the Energy

  13. Development of a 500 Watt High Temperature Thermoelectric Generator

    Broader source: Energy.gov [DOE]

    A low temperature TEG has been built and tested providing over 500 watts electric power at a ∆T of 2000C

  14. Sequoia ranked third in TOP500 list | National Nuclear Security...

    National Nuclear Security Administration (NNSA)

    according to the industry-standard Top500 list. Sequoia, which recently completed its transition to classified computing in support of NNSA's Stockpile Stewardship Program,...

  15. EIS-0514: Colusa-Sutter 500-kilovolt Transmission Line Project...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Colusa and Sutter Counties, California EIS-0514: Colusa-Sutter 500-kilovolt Transmission Line Project; Colusa and Sutter Counties, California Summary Western Area Power ...

  16. Sequoia supercomputer tops Graph 500 | National Nuclear Security...

    National Nuclear Security Administration (NNSA)

    Lawrence Livermore National Laboratory scientists' search for new ways to solve large complex national security problems led to the top ranking on Graph 500 and new techniques for ...

  17. NREL's Clean Energy Forum Attracts Nearly 500 Participants from...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    NREL's Clean Energy Forum Attracts Nearly 500 Participants from Investment Community Three Clean Energy Companies Honored at Awards Event October 21, 2010 The U.S. Department of ...

  18. Engineering Study of 500 ML Sample Bottle Transportation Methods

    SciTech Connect (OSTI)

    BOGER, R.M.

    1999-08-25

    This engineering study reviews and evaluates all available methods for transportation of 500-mL grab sample bottles, reviews and evaluates transportation requirements and schedules and analyzes and recommends the most cost-effective method for transporting 500-mL grab sample bottles.

  19. Energy Department Invests $600,000 in University-Industry Partnerships...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    600,000 in University-Industry Partnerships to Enhance Building Efficiency Energy Department Invests 600,000 in University-Industry Partnerships to Enhance Building Efficiency ...

  20. High-Definition Differential Ion Mobility Spectrometry with Resolving Power up to 500

    SciTech Connect (OSTI)

    Shvartsburg, Alexandre A.; Seim, Thomas A.; Danielson, William F.; Norheim, Randolph V.; Moore, Ronald J.; Anderson, Gordon A.; Smith, Richard D.

    2013-01-20

    As the resolution of analytical methods improve, further progress tends to be increasingly limited by instrumental parameter instabilities that could be ignored before. This is now the case with differential ion mobility spectrometry (FAIMS), where fluctuations of the voltages and gas pressure have become critical. A new high-definition generator for FAIMS compensation voltage reported here provides a stable and accurate output than can be scanned with negligible steps. This reduces the spectral drift and peak width, thus improving the resolving power (R) and resolution. The gain for multiply-charged peptides that have narrowest peaks is up to ~40%, and R ~ 400 - 500 is achievable using He/N2 or H2/N2 gas mixtures.

  1. The design, fabrication, operation and maintenance of (41) 400 H. P. -600 SCFM helium screw compressor systems (Five-year operation report)

    SciTech Connect (OSTI)

    Pallaver, C.

    1988-12-01

    Fermi National Accelerator Laboratory (Fermilab) uses thirty-four (34) identical compressor systems connected to a common header to supply clean high pressure helium gas feeding 26 refrigerators supplying liquid helium to 777 super conducting magnets. There are seven (7) similar compressor packages in other locations. The purpose of this paper is (after five years of operation) to present all the problems, modifications and experiences associated with the design and operation of these compressor systems.

  2. Obama Administration Announces Additional $9,593,500 for Local...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    the District of Columbia Obama Administration Announces Additional 9,593,500 for Local Energy Efficiency Improvements in the District of Columbia March 26, 2009 - 12:00am Addthis...

  3. Labor Department Offers $500 Million for Clean Energy Job Training

    Office of Energy Efficiency and Renewable Energy (EERE)

    The U.S. Department of Labor recently launched five grant competitions, totaling $500 million, to fund projects that prepare workers for green jobs in the energy efficiency and renewable energy industries.

  4. Obama Administration Announces Additional $13,167,500 for Local...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    ... Funding for state, city, and county governments in the state includes: SD South DakotaTotal Sum City, County, and SEO Allocations All 13,167,500 SD South Dakota State Energy ...

  5. $422,500 in scholarships awarded to 78 regional students

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    $422,500 scholarships Community Connections: Your link to news and opportunities from Los Alamos National Laboratory Latest Issue: September 1, 2016 all issues All Issues » submit $422,500 in scholarships awarded to 78 regional students Since inception, $5 million in total has benefited more than 1,000 students May 1, 2015 2015 LAESF Gold Scholar Charlotte Flory from Questa. 2015 LAESF Gold Scholar Charlotte Flory from Questa. Contact Community Programs Director (Acting) Carole Rutten Email

  6. Northern New Mexico students receive $419,500 in scholarships

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Northern New Mexico students receive $419,500 in scholarships Community Connections: Your link to news and opportunities from Los Alamos National Laboratory Latest Issue: September 1, 2016 all issues All Issues » submit Northern New Mexico students receive $419,500 in scholarships Awards go to seven northern New Mexico counties May 5, 2014 Bernalillo High School senior Raymond Fasano is LAESF's 2014 Platinum Scholarship recipient. Bernalillo High School senior Raymond Fasano is LAESF's 2014

  7. State Waste Discharge Permit application: 400 Area Septic System

    SciTech Connect (OSTI)

    Not Available

    1994-06-01

    As part of the Hanford Federal Facility Agreement and Consent Order negotiations, the US Department of Energy, Richland Operations Office, the US Environmental Protection Agency, and the Washington State Department of Ecology agreed that liquid effluent discharges to the ground on the Hanford Site which affects groundwater or has the potential to affect groundwater would be subject to permitting under the structure of Chapter 173-216 (or 173-218 where applicable) of the Washington Administrative Code, the State Waste Discharge Permit Program. This document constitutes the State Waste Discharge Permit application for the 400 Area Septic System. The influent to the system is domestic waste water. Although the 400 Area Septic System is not a Public Owned Treatment Works, the Public Owned Treatment Works application is more applicable than the application for industrial waste water. Therefore, the State Waste Discharge Permit application for Public Owned Treatment Works Discharges to Land was used.

  8. 2016_stip_attendees_400.jpg | OSTI, US Dept of Energy Office of Scientific

    Office of Scientific and Technical Information (OSTI)

    and Technical Information 2016_stip_attendees_400.jpg

  9. Alkaline intergranular corrosion and stress corrosion cracking of Alloy 600

    SciTech Connect (OSTI)

    Nagano, N.

    1996-12-31

    Intergranular corrosion (IGC), often termed IGA, and intergranular stress corrosion cracking (IGSCC) have continued to occur on mill-annealed (MA) Alloy 600 tubing in the secondary side of steam generators, which are still serious corrosion instances in operating pressurized water reactors. The IGC and IGSCC phenomena have occurred on MA Alloy 600 at the crevice between the tube and tube support plate, in which a high concentration of caustic solution is formed under dry and wet conditions at high temperature. A review of technical articles has been performed concerning environmental and metallurgical factors affecting the IGC and IGSCC, and their mechanistic aspects. A combination of IGC and IGSCC, one of the most common modes of corrosion on the secondary side of steam generators, occurs in a specific potential region, at the active-passive transition potential, in a concentrated caustic solution at elevated temperature. The anodic dissolution of Alloy 600 increases as the temperature of caustic solutions is increased. The corrosion rate for each constituent of Alloy 600 such as nickel, chromium, iron or chromium carbide is influenced differently by temperature, resulting in various effects on the characteristics of corrosion protective surface films. Increase in chromium content and thermal treatment at 700 C are beneficial for IGC and IGSCC resistance. IGC is intergranular corrosion, and IGSCC is initiated above a critical applied stress. Grain boundary chromium carbides such as Cr{sub 7}C{sub 3} and Cr{sub 23}C{sub 6} have been formed to increase resistance to IGC and IGSCC. Several theories have been proposed concerning the roles of chromium carbides at grain boundaries. Some specific theories are focused on in this paper with supporting data.

  10. Analysis of Alloy 600 and X-750 stress corrosion cracks

    SciTech Connect (OSTI)

    Thompson, C.D.; Lewis, N.; Krasodomski, H.

    1993-06-01

    A few months ago, KAPL evidence supported the view that Primary or Pure Water Stress Corrosion Cracking (PWSCC) of Alloy 600 results from a hydrogen mechanism. Figure 1 shows an Analytical Electron Microscope (AEM) analysis of a stress corrosion crack (SCC) crack in an A600 split tube U-bend specimen exposed to primary water at 338{degree}C (640{degrees}F) for 462 days. The features which appear to confirm a hydrogen mechanism are: (1) A very narrow (< 200 {angstrom}) crack with a sharp tip, nearly free of deposits. (2) No evidence of severe plastic deformation in the region immediately ahead of the crack tip. (3) A line of small voids preceding the main crack tip, of which the largest is about 5 x 10{sup {minus}6} cm in length. Shen and Shewmon proposed that PWSCC of Alloy 600 occurs due to small microvoids ahead of a main crack tip. The hypothesis is that such voids result from pockets of methane gas formed by the reaction of atomic hydrogen with carbon in the base metal. The voids are about 10 x 10{sup {minus}6} cm diameter, approximately a factor of 2 larger than the largest voids.

  11. Battery500 Consortium to Spark EV Innovations: Pacific Northwest National

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Laboratory-led, 5-year $50M effort seeks to almost triple energy stored in electric car batteries | Department of Energy Battery500 Consortium to Spark EV Innovations: Pacific Northwest National Laboratory-led, 5-year $50M effort seeks to almost triple energy stored in electric car batteries Battery500 Consortium to Spark EV Innovations: Pacific Northwest National Laboratory-led, 5-year $50M effort seeks to almost triple energy stored in electric car batteries July 28, 2016 - 10:08am Addthis

  12. Neutron diffraction measurements of intergranular strains in MONEL-400

    SciTech Connect (OSTI)

    Holden, T.M.; Holt, R.A.; Clarke, A.P.

    1997-12-01

    Measurements have been made of the strain response parallel and perpendicular to an applied stress in uniaxial tensile specimens of MONEL-400. The diffraction elastic constants are in close agreement with the Kroener model. Beyond the yield point, different crystallographic orientations respond quite differently to the applied stress and, upon unloading, residual intergranular strains are generated which are tensile for some orientations and compressive for others. A simple theory based on the Taylor-Bishop-Hill (TBH) model gives a good qualitative description of the effects.

  13. Alloy 400 tube failures by stress corrosion cracking

    SciTech Connect (OSTI)

    Amar, A.S.

    1995-12-01

    A feedwater heater with SB163 Alloy 400 (cold drawn - stress relieved) tubing experienced numerous tube failures and was replaced after of 4.5 years. Failures were attributed to Inter Granular Stress Corrosion Cracking (IGSCC) in the roll transition area. An eddy current test method was developed with EPRI NDE Center technical support to detect the cracks in the tubesheet region. Three tubes were pulled for metallurgical examination. Short axial cracks were found on tube inner surface. Measured crack depths were correlated with the eddy current indications. A large number of tubes were plugged. However, the heater continued to deteriorate rapidly. Potential contributors to IGSCC are discussed.

  14. History of the ZGS 500 MeV booster.

    SciTech Connect (OSTI)

    Simpson, J.; Martin; R.; Kustom, R.

    2006-05-09

    The history of the design and construction of the Argonne 500 MeV booster proton synchrotron from 1969 to 1982 is described. This accelerator has since been in steady use for the past 25 years to power the Argonne Intense Pulsed Neutron Source (IPNS).

  15. Heat-source specification 500 watt(e) RTG

    SciTech Connect (OSTI)

    Not Available

    1983-02-01

    This specification establishes the requirements for a /sup 90/SrF/sub 2/ heat source and its fuel capsule for application in a 500 W(e) thermoelectric generator. The specification covers: fuel composition and quantity; the Hastelloy S fuel capsule material and fabrication; and the quality assurance requirements for the assembled heat source. (LCL)

  16. Optical Spectroscopy Experiments on the 500 kA XP Pulsed-Power Generator

    SciTech Connect (OSTI)

    Bell, K. S.; Shelkovenko, T. A.; Pikuz, S. A.; McBride, R. D.; Blesener, I. C.; Knapp, P. F.; Hammer, D. A.; Greenly, J. B.; Maron, Y.

    2009-01-21

    Recent experiments on the 500 kA XP pulsed-power generator at Cornell University have explored the properties of optical spectra in single wires and wire arrays. In the single wire experiments, {approx}1% of the current from XP has been directed through the single wire. Spectra have been recorded using a half-meter spectrometer and a CCD camera located adjacent to the XP pulser. We are studying the visible spectra emitted by the wires and the background light from the machine hardware in order to identify the levels of current per wire for which visible spectroscopy might provide a means to measure magnetic field strength. We have also investigated the dependence of single wire visible spectra on the current, which was measured using a calibrated non-integrating Rogowski coil. UV and XUV diodes were employed to gather information about the temporal structure of the background and wire radiation. The line radiation in the spectra was recorded with wire currents at the few kA level. This is comparable to the first 10 ns of a 32-wire array experiment on 1 Ma generator and a 600-wire array at 20 MA.

  17. Title 50 CFR 600 Magnuson-Stevens Act Provisions | Open Energy...

    Open Energy Info (EERE)

    50 CFR 600 Magnuson-Stevens Act Provisions Jump to: navigation, search OpenEI Reference LibraryAdd to library Legal Document- RegulationRegulation: Title 50 CFR 600...

  18. Y-12 helps more than 600 kids for the holidays | National Nuclear...

    National Nuclear Security Administration (NNSA)

    Photo Gallery Jobs Apply for Our Jobs Our Jobs Working at NNSA Blog Home NNSA Blog Y-12 helps more than 600 kids for ... Y-12 helps more than 600 kids for the holidays WATE...

  19. Upgrading the Linac 400 MeV Switchyard

    SciTech Connect (OSTI)

    Charles M Ankenbrandt et al.

    2004-06-09

    This note describes changes in the 400 MeV beam transfer system from the Linac to improve the quality of the beam delivered to the Booster and to add the capability to direct beam to the MuCool Test Area (MTA). The new configuration has two pairs of pulsed dipole magnets on each side of the 400 MeV electrostatic Chopper. The smaller pair deflects vertically to replace the kick of the Chopper to send the beam to the Booster while the larger pair deflects horizontally to transfer the beam to the MTA. In this new scheme, the Chopper is uncharged while the beam is injected into the Booster such that the injection position does not rely on Chopper power supply regulation as it does now. A feature of the proposed upgrade is that no changes in the lattice functions are required in the lines to the Booster or to the Dump; once the four new magnets are installed, the switch between the old and new operating modes can be done from upstairs. The transfer to the MTA is already described in a previous note.

  20. Examinations of Oxidation and Sulfidation of Grain Boundaries in Alloy 600 Exposed to Simulated Pressurized Water Reactor Primary Water

    SciTech Connect (OSTI)

    Schreiber, Daniel K.; Olszta, Matthew J.; Saxey, David W.; Kruska, Karen; Moore, K. L.; Lozano-Perez, Sergio; Bruemmer, Stephen M.

    2013-06-01

    High-resolution characterizations of intergranular attack in alloy 600 (Ni-17Cr-9Fe) exposed to 325 C simulated pressurized water reactor (PWR) primary water have been conducted using a combination of scanning electron microscopy, NanoSIMS, analytical transmission electron microscopy and atom probe tomography. The intergranular attack exhibited a two-stage microstructure that consisted of continuous corrosion/oxidation to a depth of ~200 nm from the surface followed by discrete Cr-rich sulfides to a further depth of ~500 nm. The continuous oxidation region contained primarily nanocrystalline MO-structure oxide particles and ended at Ni-rich, Cr-depleted grain boundaries with spaced CrS precipitates. Three-dimensional characterization of the sulfidized region using site-specific atom probe tomography revealed extraordinary grain boundary composition changes, including total depletion of Cr across a several nm wide dealloyed zone as a result of grain boundary migration.

  1. Corrosion Test Results for Inconel 600 vs Inconel-Stainless UG Bellows

    SciTech Connect (OSTI)

    Osborne, P.E.

    2002-09-11

    The Conversion Project (CP) of the Molten Salt Reactor Experiment at Oak Ridge National Laboratory (ORNL) involves converting slightly less than 40 kg of {sup 233}U to a stable form for safe storage. The operation is performed within a few vessels interconnected by valves and 1/2-in. metal tubing. During this conversion, a particularly toxic and corrosive by-product is formed, namely aqueous hydrofluoric acid (HF). The production of HF is a result of the hydrolysis of UF{sub 6} and subsequent steam treatments of UO{sub 2}F{sub 2}. For each mole of UF{sub 6} converted, 6 mol of HF are produced. The HF that forms during conversion combines with water to produce approximately 1.5 L of 33 wt % HF. As this mixture is transferred within the process system, the tubing and valves are exposed to high concentrations of HF in liquid and vapor form. Of particular concern in the system are the almost 30 valves that have the potential for exposure to HF. For these valves, a vendor-supplied UG valve was installed. UG valves consist of an Alloy 400 (Monel) body and stem tip and Alloy 600 (Inconel) bellows. These valves have been used under experimental conditions that simulate the CP. It has been established that they have a finite life when exposed to a HF and air environment. Most failures were seen around the flange at the bottom of the bellows, and it was suspected that this flange and the weld material were not Inconel. In December 2001, the vendor confirmed that this flange was not Inconel but instead was stainless steel 316. After discussions between the vendor and ORNL staff involved with the CP effort, it was decided that the entire wetted area of the bellows would be fabricated from Alloy 600. In March 2002, four newly fabricated bellows assemblies were received from the vendor for the purposes of corrosion testing in HF. This report presents results from the corrosion tests conducted to determine if the new design of the bellows would enhance their corrosion resistance.

  2. INVESTIGATION IN HARDSURFACING A NICKEL-COPPER ALLOY (MONEL400).

    SciTech Connect (OSTI)

    CZAJKOWSKI,C.; BUTTERS,M.

    2001-12-01

    Brookhaven National Laboratory (BNL) investigated the causes of weldability problems and materials failures encountered with the application of Monel (Ni-Cu) 400 as a base material and Stellite 6 (Co-Cr) as the hard-surfacing material when using the oxyacetylene welding process. This work was performed under a cooperative research and development agreement (CRADA) with the Target Rock Division of the Curtiss-Wright Flow Control Corporation. BNL evaluated two heats of Monel 400 material. One of the heats had performed well during manufacturing, producing an acceptable number of ''good'' parts. The second heat had produced some good parts but also exhibited a peculiar type of hardsurfacing/base metal collapse during the welding process. A review of the chemistry on the two heats of material indicated that they both met the chemical requirements for Monel400. During examination of the failed component, linear indications (cracks) were evident on the valve body, both on the circumferential area (top of valve body) and below the hard surfaced weld deposit. independent measurements also indicated that the two heats met the specification requirement for the material. The heat affected zone (HAZ) also contained linear discontinuities. The valve body was welded using the oxyacetylene welding process, a qualified and skilled welder, and had been given a pre-heat of between 1400-1600 F (760-871 C), which is the Target Rock qualified procedure requirement. Both original suppliers performed mechanical testing on their material that indicated the two heats also met the mechanical property requirements of the specification. The BNL investigation into the cause of the differences between these heats of material utilized the following techniques: (1) Heat Treatment of both heats of material; (2) Hardness testing; (3) Optical microscopy; (4) Scanning electron microscope (SEM)/Fractography; and (5) Energy dispersive spectroscopy (EDS). The report concludes that the cause of the

  3. Top 500 List Recognizes Fastest Supercomputers | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    00 List Recognizes Fastest Supercomputers Top 500 List Recognizes Fastest Supercomputers June 30, 2014 - 5:25pm Addthis Titan 1 of 4 Titan Oak Ridge National Laboratory's Titan has a theoretical peak performance of more than 27 petaflops, or more than 27 quadrillion calculations per second. This enables researchers across the scientific arena, from materials to climate change to astrophysics, to acquire unparalleled accuracy in their simulations and achieve research breakthroughs more rapidly

  4. Residual Oxygen on Nb Heated to 500 C

    SciTech Connect (OSTI)

    Kirby, R.; King, F.K.; Padamsee, H.; /Cornell U., LEPP

    2005-06-10

    The superconducting accelerating cavities for the International Linear Collider will be constructed of high-residual resistivity ratio (RRR) niobium sheet. Excessive oxygen within the skin depth (several microns) will reduce the RRR and increase resistive losses. We measure the thickness of this oxide layer, following bakeout simulation, to be about 0.5 nm thick. The results suggest that this layer will very slowly disappear from the top five nm at 500 C.

  5. PG&E Plans for 500 MW of PV

    Broader source: Energy.gov [DOE]

    PG&E has developed a plan to install 500 MW of PV by the year 2015. The plan calls for 250 MW to be acquired through Power Purchase Agreements (PPA) and the other 250 MW to be purchased and owned by the utility. PG&E presented the plan at a public forum on April 27, 2009. A copy of the power point presentation is attached.

  6. Firm turns trash to steam, saves $60,500

    SciTech Connect (OSTI)

    Cohn, L.

    1982-05-17

    An incinerator/boiler system that the Ingersoll-Rand Co. uses to burn trash and produce steam for heating and parts cleaning saved the company $60,500 in avoided fuel and trash-disposal costs last year. Replacing a natural gas-fired boiler, the new system reduces the demand for gas by 14%. Heat recovered from the trash burning is transferred to the boiler to make steam. No smoke is emitted. (DCK)

  7. Spitzer IRAC mid-infrared photometry of 500-750 brown dwarf

    SciTech Connect (OSTI)

    Saumon, Didier; Leggett, Sandy K; Albert, Loic; Artigau, Etienne; Burningham, Ben; Delfosse, Xavier; Delorme, Philippe; Forveille, Thierry; Lucas, Philip W; Marley, Mark S; Pinfield, David J; Reyle, Celine; Smart, Richard L; Warren, Stephen J

    2010-10-26

    Mid-infrared data, including Spitzer warm-IRAC [3.6] and [4.5] photometry, is critical for understanding the cold population of brown dwarfs now being found, objects which have more in common with planets than stars. As effective temperature (T{sub eff}) drops from 800K to 400K, the fraction of flux emitted beyond 3 {mu}m increases rapidly, from about 40% to > 75%. This rapid increase makes a color like H-[4.5] a very sensitive temperature indicator, and it can be combined with a gravity- and metallicity-sensitive color like H-K to constrain all three of these fundamental properties, which in turn gives us mass and age for these slowly cooling objects. Determination of mid-infrared color trends also allows better exploitation of the WISE mission by the community. We use new Spitzer Cycle 6 IRAC photometry, together with published data, to present trends of color with type for L0 to T10 dwarfs. We also use the atmospheric and evolutionary models of Saumon and Marley to investigate the masses and ages of 13 very late-type T dwarfs, which have H-[4.5] > 3.2 and T{sub eff} {approx} 500K to 750K.

  8. Building C-400 Thermal Treatment 90% Remedial Design Report and Site

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Investigation | Department of Energy Building C-400 Thermal Treatment 90% Remedial Design Report and Site Investigation Building C-400 Thermal Treatment 90% Remedial Design Report and Site Investigation Full Document and Summary Versions are available for download Building C-400 Thermal Treatment 90% Remedial Design Report and Site Investigation (2.17 MB) Summary - Building C-400 Thermal Treatment Remedial Design Report and Investigation, Paducah, Kentucky (57.35 KB) More Documents &

  9. MCNP5 CALCULATIONS REPLICATING ARH-600 NITRATE DATA

    SciTech Connect (OSTI)

    FINFROCK SH

    2011-10-25

    This report serves to extend the previous document: 'MCNP Calculations Replicating ARH-600 Data' by replicating the nitrate curves found in ARH-600. This report includes the MCNP models used, the calculated critical dimension for each analyzed parameter set, and the resulting data libraries for use with the CritView code. As with the ARH-600 data, this report is not meant to replace the analysis of the fissile systems by qualified criticality personnel. The M CNP data is presented without accounting for the statistical uncertainty (although this is typically less than 0.001) or bias and, as such, the application of a reasonable safety margin is required. The data that follows pertains to the uranyl nitrate and plutonium nitrate spheres, infinite cylinders, and infinite slabs of varying isotopic composition, reflector thickness, and molarity. Each of the cases was modeled in MCNP (version 5.1.40), using the ENDF/B-VI cross section set. Given a molarity, isotopic composition, and reflector thickness, the fissile concentration and diameter (or thicknesses in the case of the slab geometries) were varied. The diameter for which k-effective equals 1.00 for a given concentration could then be calculated and graphed. These graphs are included in this report. The pages that follow describe the regions modeled, formulas for calculating the various parameters, a list of cross-sections used in the calculations, a description of the automation routine and data, and finally the data output. The data of most interest are the critical dimensions of the various systems analyzed. This is presented graphically, and in table format, in Appendix B. Appendix C provides a text listing of the same data in a format that is compatible with the CritView code. Appendices D and E provide listing of example Template files and MCNP input files (these are discussed further in Section 4). Appendix F is a complete listing of all of the output data (i.e., all of the analyzed dimensions and the

  10. Intergranular attack of alloy 600 tubing: Simulation tests: Interim report

    SciTech Connect (OSTI)

    Daret, J.

    1987-08-01

    In some steam generators, intergranular attack (IGA) has been detected on alloy 600 tubes within or near the tube sheet crevice region. Refreshed autoclave tests were performed to simulate caustic or river water in-leakage. The objective of the caustic tests was to perfect the test methodology, in order to closely simulate IGA that occurs in an actual steam generator, to identify causes and to test countermeasures in future tests. Tests with caustic pollution succeeded in producing representative IGA, and the test method is now believed applicable for studying countermeasures. The continuation of a river water fault test already tested for 4500 hours was aimed at checking if IGA was producible with only fresh water in-leakage, or if other deleterious species were involved in the cause of phenomenon. IGA was not detected for this case, which tends to indicate that another (not yet identified) specie acts as either a depassivating agent or a corrosion initiator in actual steam generators.

  11. Fabrication and Measurements of 500 MHz Double Spoke Cavity

    SciTech Connect (OSTI)

    Park, HyeKyoung; Hopper, Christopher S.; Delayen, Jean R.

    2014-12-01

    A 500 MHz β0=1 double spoke cavity has been designed and optimized for a high velocity application such as a compact electron accelerator at the Center for Accelerator Science at Old Dominion University [1] and the fabrication was recently completed at Jefferson Lab. The geometry specific to the double spoke cavity required a variety of tooling and fixtures. Also a number of asymmetric weld joints were expected to make it difficult to maintain minimal geometric deviation from the design. This paper will report the fabrication procedure, resulting tolerance from the design, initial test results and the lessons learned from the first β0=1 double spoke cavity fabrication.

  12. State waste discharge permit application: 400 Area secondary cooling water

    SciTech Connect (OSTI)

    Not Available

    1992-12-01

    This document constitutes the Washington Administrative Code 173-216 State Waste Discharge Permit Application that serves as interim compliance as required by the Consent Order DE 91NM-177, for the 400 Area Secondary Cooling Water stream. As part of the Hanford Federal Facility Agreement and Consent Order negotiations, the US Department of Energy, Richland Operations Office, the US Environmental Protection Agency, and the Washington State Department of Ecology agreed that liquid effluent discharges to the ground on the Hanford Site which affect groundwater or have the potential to affect groundwater would be subject to permitting under the structure of Chapter 173-216 (or 173-218 where applicable) of the Washington Administrative Code, the State Waste Discharge Permitting Program. As a result of this decision, the Washington State Department of Ecology and the US Department of Energy, Richland Operations Office entered in to Consent Order DE 91NM-177. The Consent Order DE 91NM-177 requires a series of permitting activities for liquid effluent discharges.

  13. INTERMEDIATE-MASS HOT CORES AT {approx}500 AU: DISKS OR OUTFLOWS?

    SciTech Connect (OSTI)

    Palau, Aina; Girart, Josep M.; Fuente, Asuncion; Alonso-Albi, Tomas; Fontani, Francesco; Sanchez-Monge, Alvaro; Boissier, Jeremie; Pietu, Vincent; Neri, Roberto; Busquet, Gemma; Estalella, Robert; Zapata, Luis A.; Zhang, Qizhou; Ho, Paul T. P.; Audard, Marc

    2011-12-20

    Observations with the Plateau de Bure Interferometer in the most extended configuration toward two intermediate-mass star-forming regions, IRAS 22198+6336 and AFGL 5142, reveal the presence of several complex organic molecules at {approx}500 AU scales, confirming the presence of hot cores in both regions. The hot cores are not rich in CN-bearing molecules, as often seen in massive hot cores, and are mainly traced by CH{sub 3}CH{sub 2}OH, (CH{sub 2}OH){sub 2}, CH{sub 3}COCH{sub 3}, and CH{sub 3}OH, with, additionally, CH{sub 3}CHO, CH{sub 3}OD, and HCOOD for IRAS 22198+6336, and C{sub 6}H and O{sup 13}CS for AFGL 5142. The emission of complex molecules is resolved down to sizes of {approx}300 and {approx}600 AU, for IRAS 22198+6336 and AFGL 5142, respectively, and most likely is tracing protostellar disks rather than flattened envelopes or toroids as is usually found. This is especially clear for the case of IRAS 22198+6336, where we detect a velocity gradient for all the mapped molecules perpendicular to the most chemically rich outflow of the region, yielding a dynamic mass {approx}> 4 M{sub Sun }. As for AFGL 5142, the hot core emission is resolved into two elongated cores separated {approx}1800 AU. A detailed comparison of the complex molecule peaks to the new CO (2-1) data and H{sub 2}O maser data from the literature suggests also that for AFGL 5142 the complex molecules are mainly associated with disks, except for a faint and extended molecular emission found to the west, which is possibly produced in the interface between one of the outflows and the dense surrounding gas.

  14. Stress corrosion cracking of Alloy 600 in high temperature water

    SciTech Connect (OSTI)

    Congleton, J.; Parkins, R.N.; Hemsworth, B.

    1987-01-01

    Slow strain rate stress corrosion tests have been performed on specimens cut from four separate heats of alloy 600 steam generator tubing. Material was tested in the mill annealed and thermally stabilized conditions and after various low temperature aging treatments. Only limited cracking was observed, even for tests at 340/sup 0/C, but the initiation of intergranular cracking was easier on the inner than on the outer surfaces of the tubing. Polarization data has been obtained in high temperature water and in saturated boric acid and saturated lithium hydroxide at the atmospheric boiling points, and slow strain tests were performed at controlled potentials in these environments. Again, only very short cracks formed during the slow strain rate tests which were performed at a strain rate of about 10/sup -6/ s/sup -1/. The data is discussed in terms of the probable crack tip strain rates that would exist in these tests and at other strain rates. It is argued that if cracking occurs, the main role of very low strain rate tests is to provide time for initiation and crack growth, so that cyclic loading or intermittent loading long tests are likely to be more successful in sustaining crack growth in this alloy.

  15. Development of ARH-600, a criticality safety handbook

    SciTech Connect (OSTI)

    Carter, R.D.; Blyckert, W.A.

    1997-12-01

    During 1965 or 1966, the last years of General Electric Company`s presence at Hanford, the criticality safety staff of the 200 area decided that there was a need to develop a compilation of data for use in criticality safety analysis. The official reason was that there was a need for a reference for the design engineers so that they would not have to contact us so much during preliminary design preparation. The real reason, or at least 75% of it, was so the staff could have a single point of reference rather than having to look among a rather large number of documents and other references, any one of which could disappear without notice. This was not the only criticality handbook available; Jack Chalmers in England had prepared the AHSB(S) Handbook 1, and there were others that slightly preceded our data compilation. However, these data compilations were too limited for our purposes. The tried and true documents TID-7016 and TID-7028 were also available but did not meet all our needs. Our handbook was finally issued in its original form in 1968 after the Atlantic Richfield Hanford Company had become the general contractor at Hanford, hence the document number, ARH-600.

  16. Preliminary Results Of A 600 Joules Small Plasma Focus Device

    SciTech Connect (OSTI)

    Lee, S. H.; Yap, S. L.; Wong, C. S.

    2009-07-07

    Preliminary results of a 600 J (3.7 muF, 18 kV) Mather type plasma focus device operated at low pressure will be presented. The discharge is formed between a solid anode with length of 6 cm and six symmetrically and coaxially arranged cathode rods of same lengths. The cathode base is profiled in a knife-edge design and a set of coaxial plasma gun are attached to it in order to initiate the breakdown and enhance the current sheath formation. The experiments have been performed in argon gas under a low pressure condition of several microbars. The discharge current and the voltage across the electrodes during the discharge are measured with high voltage probe and current coil. The current and voltage characteristics are used to determine the possible range of operating pressure that gives good focusing action. At a narrow pressure regime of 9.0+-0.5 mubar, focusing action is observed with good reproducibility. Preliminary result of ion beam energy is presented. More work will be carried out to investigate the radiation output.

  17. 500-kW DCHX pilot-plant evaluation testing

    SciTech Connect (OSTI)

    Hlinak, A.; Lee, T.; Loback, J.; Nichols, K.; Olander, R.; Oshmyansky, S.; Roberts, G.; Werner, D.

    1981-10-01

    Field tests with the 500 kW Direct Contact Pilot Plant were conducted utilizing brine from well Mesa 6-2. The tests were intended to develop comprehensive performance data, design criteria, and economic factors for the direct contact power plant. The tests were conducted in two phases. The first test phase was to determine specific component performance of the DCHX, turbine, condensers and pumps, and to evaluate chemical mass balances of non-condensible gases in the IC/sub 4/ loop and IC/sub 4/ in the brine stream. The second test phase was to provide a longer term run at nearly fixed operating conditions in order to evaluate plant performance and identify operating cost data for the pilot plant. During these tests the total accumulated run time on major system components exceeded 1180 hours with 777 hours on the turbine prime mover. Direct contact heat exchanger performance exceeded the design prediction.

  18. The 18. annual P and GJ 500 Report

    SciTech Connect (OSTI)

    Share, J.; Tubb, R.

    1998-11-01

    The staff of Pipeline and Gas Journal presents its 18th annual 500 Report, providing the industry`s most comprehensive summary of the nation`s energy pipeline systems. As usual, categories are broken down to include the top liquids pipelines, gas transmission and distribution systems. The transmission companies are ranked by mileage while the liquids companies are determined by numbers of barrels. The gas distribution rankings are determined by number of customers. Other numbers include total throughput of natural gas and barrels of crude oil and refined products; operating revenue and net income; miles of mains and service lines; compression; and additions to plant. The figures for the most part represent calendar year 1997 statistics as compared to 1996. One interesting note: the mild winter of 1997--98 throughout most of the East Coast and Midwest led to a decrease in volume, especially for natural gas, and a resulting decline in revenues for a substantial number of companies.

  19. The 16th P and GJ 500 report

    SciTech Connect (OSTI)

    Share, J.

    1996-09-01

    Pipeline and Gas Journal is pleased to present its 16th annual 500 Report--a comprehensive listing of the nation`s energy pipelines. The list comprises the leading 300 natural gas distribution utilities; top 100 gas transmission pipelines and top 100 liquids pipelines. The wealth of statistics includes pipeline mileage; total throughput of gas and barrels of crude oil and refined products; operating revenue; employees; and in the case of the gas distributors their number of customers. Just as important as the numbers are the trends they reveal of an energy industry continuing to undergo dramatic change. The gas industry in particular has faced a massive reorganization caused in large part by Federal Energy Regulatory Commission Order 636.

  20. The 17th annual P and GJ 500 report

    SciTech Connect (OSTI)

    Share, J.; Tubb, R.

    1997-11-01

    The staff of Pipeline and Gas Journal presents its 17th annual 500 Report, providing the industry`s most comprehensive statistical summary of the nation`s energy pipelines. The report was previously printed every September but has been moved to November to accommodate the new deadlines for pipeline companies to file their necessary paperwork with the Federal Energy Regulatory Commission. The report contains listings of the 300 leading natural gas distribution utilities; the top 100 transmission and gathering pipelines and the top 100 liquids pipelines. The distribution companies are ranked according to number of customers while gas pipelines are ranked by mileage. The liquids companies are determined by barrels. Other numbers include total throughput of natural gas and barrels of crude oil and refined products; operating revenue and net income; miles of mains and service lines, compression; and additions to plant.

  1. Nondestructive Testing Qualification of Main Circulatory Tube Pipes DU 500

    SciTech Connect (OSTI)

    Tabakova, Bojana M.; Tzokov, Petio

    2004-07-01

    The criteria for safe operation of nuclear energetic installations is given a higher priority in the policy of Kozloduy Nuclear Power Plant. An efficient non-destructive inspection is the key point for the safe service. Kozloduy NPP keeps on making investments in equipment and qualification of specialists in this field. The processes of qualification of the NDT components, important for the nuclear and radiation safety, make considerable improvement in Kozloduy NPP, thanks to the accumulated in the years experience in the activities of NDT inspection qualification, and to the help of our partners Serco Assurance and the Institute of Rzes. The results obtained by ultrasonic non-destructive inspection of circulation tube mains DU 500 WWER 440 type are under discussion in this report. (authors)

  2. Department of Energy Awards $600,000 to Tri-City Industrial Developmen...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Industrial Development Council Community Reuse Organization Department of Energy Awards 600,000 to Tri-City Industrial Development Council Community Reuse Organization Department ...

  3. Department of Energy Closes $400 Million Loan Guarantee for State of the

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Art Solar Manufacturing in Indiana and Colorado | Department of Energy Closes $400 Million Loan Guarantee for State of the Art Solar Manufacturing in Indiana and Colorado Department of Energy Closes $400 Million Loan Guarantee for State of the Art Solar Manufacturing in Indiana and Colorado December 14, 2010 - 12:00am Addthis Washington D.C. - U.S. Energy Secretary Steven Chu announced today that a $400 million loan guarantee has been finalized for Abound Solar Manufacturing, LLC to

  4. Title 11 Alaska Administrative Code 82.400 - 82.475 Competitive...

    Open Energy Info (EERE)

    Reference LibraryAdd to library Legal Document- RegulationRegulation: Title 11 Alaska Administrative Code 82.400 - 82.475 Competitive BiddingLegal Abstract Implementing...

  5. AAC R17-3-500 Highway Encroachments and Permits | Open Energy...

    Open Energy Info (EERE)

    3-500 Highway Encroachments and Permits Jump to: navigation, search OpenEI Reference LibraryAdd to library Legal Document- RegulationRegulation: AAC R17-3-500 Highway Encroachments...

  6. Stress corrosion cracking resistance of alloys 600 and 690 and compatible weld metals in BWRs: Final report

    SciTech Connect (OSTI)

    Page, R. A.; McMinn, A.

    1988-07-01

    The relative susceptibilities of alloy 600 and 690 base metals and I-82, I-182, R-127 and R-135 weld metals to intergranular stress corrosion cracking (IGSCC) in either pure water or a simulated resin intrusion environment at 288/degree/C were evaluated. Alloy 600, I-182, and I-82 weld metals were susceptible to various degrees of IGSCC in oxygen containing pure water when creviced, and immune to IGSCC when uncreviced. Alloy 690 was immune to IGSCC under all pure water conditions. Alloy 500, alloy 690, I-182, and I-82 were all susceptible to cracking in the simulated resin intrusion environment, although alloy 690 exhibited the greatest resistance to SCC. The high chromium experimental weld alloy were immune to cracking under all conditions examined. The IGSCC susceptibility of seven different weld metals used to weld alloy 600 and A508 were also evaluated in the resin intrusion environment at 288/degree/C. Weldments made with I-625, I-182, and I-82 (GTAW) were the most susceptible, whereas welds made with I-132 were the least susceptible. Most of the weldments failed at the fusion line between the weld metal and the A508 steel, and the SCC susceptibility increased with increasing hardness measured at the fusion line. There was no effect of crevice condition or heat treatment on SCC susceptibility. The SCC susceptibility of Type 316 NG stainless steel welded with R-127, R-135, I-72 and Type 308L weld metals was evaluated in pure water and resin intrusion environments at 288/degree/C. All of the materials were immune to SCC in the pure water environment. In the resin intrusion environment, both the I-72 and R-135 weld metals were immune to SACC, but the R-127 and Type 308L weld metals exhibited SCC. The Type 316 NG stainless steel was susceptible to transgranular SCC in the resin intrusion environment, except when welded with I-72, in which case it was immune. 36 refs., 4 tabs.

  7. With 400th Ph.D. grad, UW-Madison celebrates a half century of fusion

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    energy | Princeton Plasma Physics Lab With 400th Ph.D. grad, UW-Madison celebrates a half century of fusion energy American Fusion News Category: U.S. Universities Link: With 400th Ph.D. grad, UW-Madison celebrates a half century of fusion energy

  8. Effect of lithium hydroxide on primary water stress corrosion cracking of Alloy 600 tubing

    SciTech Connect (OSTI)

    Jacko, R. )

    1991-09-01

    Primary water stress corrosion cracking (PWSCC) studies were performed on Alloy 600 in simulated PWR high lithium primary water. Tests were conducted at 330{degree}C with Li concentrations ranging from 0.7 to 3.5 ppM in solutions containing boric acid and dissolved hydrogen. Highly stressed, Alloy 600 reverse U-bend specimens (RUBs) were predominantly used for tests. Both mill-annealed (MA) and thermally treated (TT) Alloy 600 were tested. The large number of specimens tested allowed the use of rigorous statistical techniques to interpret the variability of PWSCC performance. Results of tests of MA 600 RUBs at 2 stress levels show no effect of chemistry on the time to initiate PWSCC cracks over the range from 0.7 to 3.5 ppM Li. However, results for TT 600 RUBs and in MA 600 RUBs at a third stress level show the tendency for a shorter time to initiate PWSCC cracks at a Li concentration of 3.5 ppM. Analysis suggests that certain Alloy 600 components may experience an increase in PWSCC by using the higher LI content primary water due to a subtle influence of chemistry on PWSCC. 5 refs. 8 figs., 3 tabs.

  9. Description of the OSU APEX test facility to assess AP600 passive safety

    SciTech Connect (OSTI)

    Hochreiter, L.E.; Lau, L.K.; Reyes, J.N. Jr.; Groome, J.T.

    1995-12-31

    The objective of this paper is to describe the Advanced Plant Experiment (APEX) test facility, which is a new integral system test facility located at Oregon State University (OSU) specifically scaled, designed, and built to simulate all of the important geometrical details of the Westinghouse AP600. The APEX facility has been designed and constructed to develop a database that can be used to validate the thermal hydraulic safety analysis codes that will be used in the AP600 design certification process. The test facility has been specifically designed and scaled to model small break loss-of-coolant and long-term cooling transients, which utilize the AP600 passive safety systems.

  10. Energy Department Announces Major Recovery Act Milestone: 600,000 Homes

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Weatherized Three Months Ahead of Schedule | Department of Energy Major Recovery Act Milestone: 600,000 Homes Weatherized Three Months Ahead of Schedule Energy Department Announces Major Recovery Act Milestone: 600,000 Homes Weatherized Three Months Ahead of Schedule December 15, 2011 - 1:07pm Addthis Washington, D.C. -- U.S. Energy Secretary Steven Chu today announced that states and territories across the nation have reached the goal of weatherizing more than 600,000 low-income homes-

  11. NMR Analysis of Methyl Groups at 100-500 kDa: Model Systems and Arp2/3 Complex

    SciTech Connect (OSTI)

    Kreishman-Deitrick, Mara; Egile, Coumaran; Hoyt, David W.; Ford, Joseph J.; Rong, Li; Rosen, Michael K.

    2003-07-01

    Large macromolecular machines are among the most important and challenging targets for structural and mechanistic analyses. Consequently, there is great interest in development of NMR methods for the study of multicomponent systems in the 50-500 kDa range. Biochemical methods also must be developed in concert to produce such systems in selectively labeled form. Here, we present 1H/13C-HSQC spectra of protonated methyl groups in a model system that mimics molecular weights up to ~560 kDa. Signals from side chain methyl groups of Ile, Leu, and Val residues are clearly detectable at correlation times up to ~330 ns. We have also developed a biochemical procedure to produce the 240 kDa, heteroheptameric Arp2/3 actin nucleation complex selectively labeled at one subunit and obtained 1H/13C-HSQC spectra of this assembly. Sensitivity in spectra of both the Arp2/3 complex and the model system indicate that methyl groups will be useful sources of information in nonsymmetric systems with molecular weights greater than 600 kDa at concentrations less than 100 μM. Methyl analyses will complement TROSY and CRINEPT analyses of amides in NMR studies of structure and molecular interactions of extremely large macromolecules and assemblies.

  12. Operation and Development of the 500-keV Negative-Ion-Based Neutral Beam Injection System for JT-60U

    SciTech Connect (OSTI)

    Kuriyama, M.; Akino, N.; Ebisawa, N.; Grisham, L.; Honda, A.; Itoh, T.; Kawai, M.; Kazawa, M.; Mogaki, K.; Ohara, Y.; Ohga, T.; Okumura, Y.; Oohara, H.; Umeda, N.; Usui, K.; Watanabe, K.; Yamamoto, M.; Yamamoto, T.

    2002-09-15

    The 500-keV negative-ion based neutral beam injector for JT-60U started operation in 1996. The beam power has been increased gradually through optimizing operation parameters of the ion sources and conquering many troubles in the ion source and power supplies caused by a high voltage break-down in the accelerator. However, some issues remain to be solved concerning the ion source for increasing further the beam power and the beam energy. The most serious issue of them is non-uniformity of source plasma in the arc chamber. Various countermeasures have been implemented to improve the non-uniformity. Some of those countermeasures have been found to be partially effective in reducing the non-uniformity of the source plasma, and as the result the ion source, so far, has accelerated negative-ion beams of 17.4A at 403keV with deuterium and 20A at 360keV with hydrogen against the goal of 22A at 500keV. The neutral beam injection power into the plasma has reached 5.8MW at 400keV with deuterium. Further efforts to reach the target of 10MW at 500keV have been continued.

  13. TYPE IIn SUPERNOVA SN 2010jl: OPTICAL OBSERVATIONS FOR OVER 500 DAYS AFTER EXPLOSION

    SciTech Connect (OSTI)

    Zhang Tianmeng; Wu Chao; Zhai Meng; Wu Hong; Fan Zhou; Zou Hu; Zhou Xu; Ma Jun; Wang Xiaofeng; Chen Juncheng; Chen Jia; Liu Qin; Huang Fang; Liang Jide; Zhao Xulin; Lin Lin; Wang Min; Dennefeld, Michel; Zhang Jujia E-mail: wang_xf@mail.tsinghua.edu.cn

    2012-11-01

    We present extensive optical observations of a Type IIn supernova (SN IIn) 2010jl for the first 1.5 years after its discovery. The UBVRI light curves demonstrated an interesting two-stage evolution during the nebular phase, which almost flatten out after about 90 days from the optical maximum. SN 2010jl has one of the highest intrinsic H{alpha} luminosities ever recorded for an SN IIn, especially at late phase, suggesting a strong interaction of SN ejecta with the dense circumstellar material (CSM) ejected by the progenitor. This is also indicated by the remarkably strong Balmer lines persisting in the optical spectra. One interesting spectral evolution about SN 2010jl is the appearance of asymmetry of the Balmer lines. These lines can be well decomposed into a narrow component and an intermediate-width component. The intermediate-width component showed a steady increase in both strength and blueshift with time until t {approx} 400 days after maximum, but it became less blueshifted at t {approx} 500 days, when the line profile appeared relatively symmetric again. Owing to the fact that a pure reddening effect will lead to a sudden decline of the light curves and a progressive blueshift of the spectral lines, we therefore propose that the asymmetric profiles of H lines seen in SN 2010jl are unlikely due to the extinction by newly formed dust inside the ejecta, contrary to the explanation by some early studies. Based on a simple CSM-interaction model, we speculate that the progenitor of SN 2010jl may suffer a gigantic mass loss ({approx}30-50 M{sub Sun }) a few decades before explosion. Considering a slow-moving stellar wind (e.g., {approx}28 km s{sup -1}) inferred for the preexisting, dense CSM shell and the extremely high mass-loss rate (1-2 M{sub Sun} yr{sup -1}), we suggest that the progenitor of SN 2010jl might have experienced a red supergiant stage and may explode finally as a post-red supergiant star with an initial mass above 30-40 M{sub Sun }.

  14. DOE's Carbon Utilization and Storage Atlas Estimates at Least 2,400 Billion

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Metric Tons of U.S. CO2 Storage Resource | Department of Energy DOE's Carbon Utilization and Storage Atlas Estimates at Least 2,400 Billion Metric Tons of U.S. CO2 Storage Resource DOE's Carbon Utilization and Storage Atlas Estimates at Least 2,400 Billion Metric Tons of U.S. CO2 Storage Resource December 19, 2012 - 12:00pm Addthis Washington, DC - The United States has at least 2,400 billion metric tons of possible carbon dioxide (CO2) storage resource in saline formations, oil and gas

  15. Energy Department Invests $600,000 in University-Industry Partnerships to Enhance Building Efficiency

    Broader source: Energy.gov [DOE]

    The Energy Department today announced $600,000 in funding to help American universities to establish stronger partnerships with industry and business in the area of building efficiency, supporting...

  16. SNR Denton US LLP 1301 K Street, NW Suite 600, East Tower Washington...

    Broader source: Energy.gov (indexed) [DOE]

    SNR Denton US LLP 1301 K Street, NW Suite 600, East Tower Washington, DC 20005-3364 USA Thomas C. Jensen Partner thomas.jensen@snrdenton.com D +1 202 408 3956 M 703 304 5211 T +1 ...

  17. Stress corrosion cracking of Alloys 600 and 182 in BWR environments

    SciTech Connect (OSTI)

    Ljungberg, L.G.; Hofling, C.G.; Sahlberg, A.; Moeller, J. )

    1992-05-01

    Wrought Alloy 600 and weldments of Alloy 182 are being tested for initiation and propagation of intergranular stress corrosion cracking (IGSCC). Crack initiation is tested on compact tension (CT) specimens with U-notches of various radii under enhanced crevice conditions, in a test loop in a Swedish BWR. After one year exposure there was initiation of IGSCC in a large portion of the Alloy 182 specimens, but nearly no initiation in Alloy 600. Crack propagation was measured in a laboratory loop on CT specimens under constant or cyclic load. Low carbon Alloy 600, or Alloy 182 high in titanium and niobium versus carbon, cracked at lower rates than material with high carbon activity. Materials with low concentrations of phosphorus and sulfur cracked slower than those high in these elements in clean environment, but no such effect was found in environment with sulfate. Alloy 182 weld metal generally cracked at higher rates than Alloy 600.

  18. Stress corrosion cracking of Alloys 600 and 182 in BWR environments. Interim report

    SciTech Connect (OSTI)

    Ljungberg, L.G.; Hofling, C.G.; Sahlberg, A.; Moeller, J.

    1992-05-01

    Wrought Alloy 600 and weldments of Alloy 182 are being tested for initiation and propagation of intergranular stress corrosion cracking (IGSCC). Crack initiation is tested on compact tension (CT) specimens with U-notches of various radii under enhanced crevice conditions, in a test loop in a Swedish BWR. After one year exposure there was initiation of IGSCC in a large portion of the Alloy 182 specimens, but nearly no initiation in Alloy 600. Crack propagation was measured in a laboratory loop on CT specimens under constant or cyclic load. Low carbon Alloy 600, or Alloy 182 high in titanium and niobium versus carbon, cracked at lower rates than material with high carbon activity. Materials with low concentrations of phosphorus and sulfur cracked slower than those high in these elements in clean environment, but no such effect was found in environment with sulfate. Alloy 182 weld metal generally cracked at higher rates than Alloy 600.

  19. Application for Presidential Permit PP-400 TDI-NE - New England...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    PP-400 TDI-NE - New England Clean Power Link Project - Motion to Intervene and Comments of the Vermont Department of Public Service - August 6, 2014 Application for Presidential ...

  20. Oil Shale Market is Estimated to Reach USD 7,400.70 Million by...

    Open Energy Info (EERE)

    Oil Shale Market is Estimated to Reach USD 7,400.70 Million by 2022 Home > Groups > Renewable Energy RFPs Wayne31jan's picture Submitted by Wayne31jan(150) Contributor 1 July, 2015...

  1. U.S. Department of Energy Announces Completion of 500 Industrial Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Saving Assessment | Department of Energy Completion of 500 Industrial Energy Saving Assessment U.S. Department of Energy Announces Completion of 500 Industrial Energy Saving Assessment May 9, 2008 - 11:30am Addthis Over 80 Trillion Btus of Natural Gas Savings Found WASHINGTON - The U.S. Department of Energy (DOE) today announced that it has completed the 500th Energy Saving Assessment (ESA) at the nation's largest industrial facilities. These assessments have helped companies identify

  2. Summary - Building C-400 Thermal Treatment Remedial Design Report and Investigation, Paducah, Kentucky

    Office of Environmental Management (EM)

    Paducah, KY EM Project: Building C400 Thermal Treatment ETR Report Date: August 2007 ETR-8 United States Department of Energy Office of Environmental Management (DOE-EM) External Technical Review of Building C-400 Thermal Treatment 90% Remedial Design Report and Site Investigation, Paducah Kentucky Why DOE-EM Did This Review The groundwater underlying the Paducah Gaseous Diffusion Plant (PGDP) is contaminated by chlorinated solvents, principally trichloroethylene (TCE), as well as other

  3. Obama Administration Announces Additional $102,508,400 for Local Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Efficiency Improvements in Pennsylvania | Department of Energy 02,508,400 for Local Energy Efficiency Improvements in Pennsylvania Obama Administration Announces Additional $102,508,400 for Local Energy Efficiency Improvements in Pennsylvania March 26, 2009 - 12:00am Addthis WASHINGTON - Vice President Joe Biden and Energy Secretary Steven Chu today announced plans to invest $3.2 billion in energy efficiency and conservation projects in U.S. cities, counties, states, territories, and Native

  4. Obama Administration Announces Additional $63,817,400 for Local Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Efficiency Improvements in Arizona | Department of Energy 63,817,400 for Local Energy Efficiency Improvements in Arizona Obama Administration Announces Additional $63,817,400 for Local Energy Efficiency Improvements in Arizona March 26, 2009 - 12:00am Addthis WASHINGTON - Vice President Joe Biden and Energy Secretary Steven Chu today announced plans to invest $3.2 billion in energy efficiency and conservation projects in U.S. cities, counties, states, territories, and Native American tribes.

  5. U.S. Department of Energy Announces Completion of 500 Industrial...

    Office of Environmental Management (EM)

    the 500th Energy Saving Assessment (ESA) at the nation's largest industrial facilities. These assessments have helped companies identify opportunities to save over an estimated ...

  6. EIS-0344: Grand Coulee-Bell 500 kV Transmission Line

    Broader source: Energy.gov [DOE]

    This EIS analyzes DOE's proposed action for the construction and operation of the proposed Grand Coulee-Bell 500-kV Transmission Line Project.

  7. Introduction to IEEE 841-1994, IEEE standard for petroleum and chemical industry: Severe duty totally enclosed fan-cooled (TEFC) squirrel cage induction motors -- up to and including 500 hp

    SciTech Connect (OSTI)

    Doughty, R.L.

    1995-12-31

    IEEE 841, Recommended Practice for Chemical Industry Severe Duty Squirrel-Cage Induction Motors--600 V and Below, first issued in 1986, has been significantly revised and reissued as a Standard. The scope has been increased to include severe duty TEFC squirrel-cage induction motors with antifriction bearings in sizes up to and including 500 horsepower. Motor rated voltages of 2,300 V and 4,000 V have been added. Changes to the standard are reviewed in detail. Requirements are identified that improve motor reliability and increase motor life.

  8. Use of underpotential deposition of zinc to mitigate hydrogen absorption into Monel K500

    SciTech Connect (OSTI)

    Zheng, G.; Popov, B.N.; White, R.E. . Dept. of Chemical Engineering)

    1994-05-01

    Polarization experiments and a potentiostatic pulse technique have been used to show that a monolayer coverage of zinc effectively inhibits the absorption of hydrogen into Monel K500. By depositing a monolayer of zinc on Monel K500 the hydrogen, evolution reaction and hydrogen ingress flux rate were reduced by 60%.

  9. Surface and grain boundary segregation, stress corrosion cracking, and corrosion fatigue of Inconel 600

    SciTech Connect (OSTI)

    Smialowska, S.; Cragnolino, G.; Macdonald, D.D.

    1985-03-01

    The stress corrosion cracking of Inconel 600 in environments related to nuclear power systems was studied in relation to the role of segregation in the alloy. Auger electron spectroscopy was used to evaluate the surface segregation of different impurities in Inconel 600 as a function of heat-to-heat variation and heat treatment. The degree of segregation of various elements (S, P, N, Ti, Si, and C) on the fracture surface of nickel was also evaluated as a function of the heat treatment employed, temperature, and cooling rate. The effects of alloying elements, added to nickel with the aim of reducing sulfur segregation to grain boundaries, was also studied. The susceptibility of nickel to intergranular corrosion in acidic and alkaline solutions at different potentials was measured as a function of sulfur segregation to the grain boundaries. The effect of heat treatment and applied potential on the caustic stress corrosion cracking susceptibiliy of Inconel 600 was studied in concentrated NaOH solutions at 140/sup 0/C using the slow strain rate technique. The corrosion fatigue resistance of Inconel Alloy 600 in concentrated NaOH solutions at 140/sup 0/C was evaluated as a function of heat treatment conditions using smooth bar specimens. The results have shown that the stress corrosion behavior of Inconel 600 in caustic solutions differs greatly from that in acidic and nearly neutral environments. Furthermore, sensitization by heat treatment was found to be beneficial under caustic corrosion conditions but detrimental in acidic environments.

  10. SunShot-Supported Company to Create 500 New Solar Manufacturing Jobs

    Broader source: Energy.gov [DOE]

    SunShot awardee Suniva, a manufacturer of high efficiency crystalline silicone solar cells and modules, has announced it will expand its manufacturing capacity at its Georgia headquarters to 400MW...

  11. Investigating the presence of 500 μm submillimeter excess emission in local star forming galaxies

    SciTech Connect (OSTI)

    Kirkpatrick, Allison; Calzetti, Daniela; Galametz, Maud; Kennicutt, Rob Jr.; Dale, Daniel; Aniano, Gonzalo; Sandstrom, Karin; Walter, Fabian; Armus, Lee; Crocker, Alison; Hinz, Joannah; Hunt, Leslie; Koda, Jin

    2013-11-20

    Submillimeter excess emission has been reported at 500 μm in a handful of local galaxies, and previous studies suggest that it could be correlated with metal abundance. We investigate the presence of an excess submillimeter emission at 500 μm for a sample of 20 galaxies from the Key Insights on Nearby Galaxies: a Far Infrared Survey with Herschel (KINGFISH) that span a range of morphologies and metallicities (12 + log (O/H) = 7.8-8.7). We probe the far-infrared (IR) emission using images from the Spitzer Space Telescope and Herschel Space Observatory in the wavelength range 24-500 μm. We model the far-IR peak of the dust emission with a two-temperature modified blackbody and measure excess of the 500 μm photometry relative to that predicted by our model. We compare the submillimeter excess, where present, with global galaxy metallicity and, where available, resolved metallicity measurements. We do not find any correlation between the 500 μm excess and metallicity. A few individual sources do show excess (10%-20%) at 500 μm; conversely, for other sources, the model overpredicts the measured 500 μm flux density by as much as 20%, creating a 500 μm 'deficit'. None of our sources has an excess larger than the calculated 1σ uncertainty, leading us to conclude that there is no substantial excess at submillimeter wavelengths at or shorter than 500 μm in our sample. Our results differ from previous studies detecting 500 μm excess in KINGFISH galaxies largely due to new, improved photometry used in this study.

  12. Results from the NRC AP600 testing program at the Oregon State University APEX facility

    SciTech Connect (OSTI)

    Reyes, J.N. Jr.; Bessette, D.E.; DiMarzo, M.

    1996-03-01

    The Department of Nuclear Engineering at Oregon State University (OSU) is performing a series of confirmatory tests for the U.S. Nuclear Regulatory Commission. These tests are being conducted in the Advanced Plant Experiment (APEX) facility which is a 1/4 length scale and 1/192 volume scale integral system simulation of the Westinghouse Advanced Passive 600 MWe (AP600) plant. The purpose of the testing program is to examine AP600 passive safety system performance, particularly during long term cooling. Thus far, OSU has successfully performed ten integral system tests for the NRC. This paper presents a description of the APEX facility and summarizes the important results of the NRC test program at OSU.

  13. Comparative Study of Station Blackout Counterpart Tests in APEX and ROSA/AP600

    SciTech Connect (OSTI)

    Lafi, Abd Y.; Reyes, Jose N. Jr.

    2000-05-15

    A comparison is presented between station blackout tests conducted in both the Advanced Plant Experiment (APEX) facility and in the modified Rig of Safety Assessment (ROSA/AP600) Large-Scale Test Facility. The comparison includes the depressurization and liquid-level behavior during secondary-side blowdown, natural circulation, automatic depressurization system operation, and in-containment refueling water storage tank injection. Reasonable agreement between the test results from APEX NRC-2 and ROSA/AP600 AP-BO-01 has been observed with respect to the timing of depressurization and liquid draining rates. This indicates that the reduced height and pressure scaling of APEX preserves the sequence of events relative to the full-height and pressure ROSA/AP600.

  14. Comparison of SPES-2 and APEX tests to examine AP600 integral system performance

    SciTech Connect (OSTI)

    Hochreiter, L.E.; Reyes, J.N. Jr.

    1995-12-31

    The Westinghouse Electric Corporation has performed a series of tests in the SPES-2 facility (Simulatore Per Esperienze di Sicurezza--Simulator for Safety Experimental Analysis) in Piacenza, Italy and in the APEX (Advanced Plant Experiment) facility, at Oregon State University. These testing programs are designed to evaluate the thermal hydraulic performance of the passive safety systems (gravity driven injection, natural convection, and passive cooling) of the Westinghouse Advanced Passive 600 MWe pressurized water reactor (AP600). They are also designed to obtain data that can be used to assess and validate the safety analysis techniques and computer codes being used to predict the transient system behavior of the AP600. This paper presents a comparison of the two test facility designs and the results of counterpart tests.

  15. Primary water stress corrosion crack growth rates in Alloy 600 steam generator tubing

    SciTech Connect (OSTI)

    Lott, R.G.; Jacko, R.J.; Gold, R.E.

    1992-12-31

    Direct measurements of SCC crack growth rates have been used to determine the effects of changes in PWR primary water chemistry on the stress corrosion cracking behavior of Alloy 600 steam generator tubing. Reversing current DC potential measurement techniques have been adapted for use on thin walled tubing containing through-wall circumferential cracks. These techniques have been used to monitor crack rates in Alloy 600 tubing exposed to typical PWR primary water chemistries at 330{degrees}C. Crack growth rate studies, conducted under well defined stress intensity conditions, provide a sensitivity in the assessment of stress corrosion cracking susceptibility that is not possible using more traditional techniques. Preliminary studies have been conducted to determine the effects of B and Li concentrations on the stress corrosion crack growth rate of Alloy 600 tubing.

  16. Primary water stress corrosion cracking inspection ranking scheme for Alloy 600 components

    SciTech Connect (OSTI)

    Hoang, P.H.; Gangadharan, A.; Ramalingam, S.C.

    1996-12-31

    Palisades Nuclear Plant has developed a comprehensive inspection program to support safe, reliable, and cost-effective operation of all Alloy 600 nozzles and safe ends in the primary coolant system (PCS). As a part of the Palisades Alloy 600 Project, an inspection prioritization scheme was developed to help the plant focus its resources on high risk components and plan appropriate inspection activities for the other components. The inspection prioritization scheme is based on the susceptibility of the components to Primary Water Stress Corrosion Cracking (PWSCC), component failure consequences, component leak detectability and component radiation exposure. The scheme provides a simple, systematic and technical base for selecting Alloy 600 components for inspection. The scheme, however, could be used to develop an inspection schedule or to select the highest priority components for mitigation or replacement.

  17. Contractors Donate Nearly $600,000 to Charity | Department of Energy

    Office of Environmental Management (EM)

    Contractors Donate Nearly $600,000 to Charity Contractors Donate Nearly $600,000 to Charity February 11, 2016 - 12:15pm Addthis Bechtel employees celebrate a $100,000 gift to Friends of Badger Mountain at Trailhead Park in Richland. Bechtel employees celebrate a $100,000 gift to Friends of Badger Mountain at Trailhead Park in Richland. Toys from WTP’s 2015 U.S. Marine Corps Reserve's Toys for Tots campaign are loaded into a trailer to prepare them for delivery to needy families in the

  18. Results from ORNL Characterization of Zr02-500-AK2 - Surrogate TRISO Material

    SciTech Connect (OSTI)

    Hunn, John D; Kercher, Andrew K

    2005-06-01

    This document is a compilation of the characterization data for the TRISO-coated surrogate particle batch designated ZrO2-500-AK2 that was produced at Oak Ridge National Laboratory (ORNL) as part of the Advanced Gas Reactor Fuel Development and Qualification (AGR) program. The ZrO2-500-AK2 material contains nominally 500 {micro}m kernels of yttria-stabilized zirconia (YSZ) coated with all TRISO layers (buffer, inner pyrocarbon, silicon carbide, and outer pyrocarbon). The ZrO2-500-AK2 material was created for: (1) irradiation testing in the High Flux Isotope Reactor (HFIR) and (2) limited dissemination to laboratories as deemed appropriate to the AGR program. This material was created midway into a TRISO fuel development program to accommodate a sudden opportunity to perform irradiation testing on surrogate material. While the layer deposition processes were chosen based on the best technical understanding at the time, technical progress at ORNL has led to an evolution in the perceived optimal deposition conditions since the createion of ZrO2-500-AK2. Thus, ZrO2-500-AK2 contains a reasonable TRISO microstructure, but does differ significanly from currently produced TRISO surrogates and fuel at ORNL. In this document, characterization data of the ZrO2-500-AK2 surrogate includes: size, shape, coating thickness, and density.

  19. Results from ORNL characterization of ZrO2-500-AK2 - surrogate TRISO material

    SciTech Connect (OSTI)

    Kercher, Andrew K; Hunn, John D

    2005-06-01

    This document is a compilation of the characterization data for the TRISO-coated surrogate particles designated ZrO2-500-AK2 that was produced at Oak Ridge National Laboratory (ORNL) as part of the Advanced Gas Reactor Fuel Development and Qualification (AGR) program. The ZrO2-500-AK2 material contains nominally 500 {micro}m kernels of yttria-stabilized zirconia (YSZ) coated with all TRISO layers (buffer, inner pyrocarbon, silicon carbide, and outer pyrocarbon). The ZrO2-500-AK2 material was created for: (1) irradiation testing in the High Flux Isotope Reactor (HFIR) and (2) limited dissemination to laboratories as deemed appropriate to the AGR program. This material was created midway into a TRISO fuel development program to accommodate a sudden opportunity to perform irradiation testing on surrogate material. While the layer deposition processes were chosen based on the best technical understanding at the time, technical progress at ORNL has led to an evolution in the perceived optimal deposition conditions since the creation of ZrO2-500-AK2. Thus, ZrO2-500-AK2 contains a reasonable TRISO microstructure, but does differ significantly from currently produced TRISO surrogates and fuel at ORNL. In this document, characterization data of the ZrO2-500-AK2 surrogate includes: size, shape, coating thickness, and density.

  20. Geothermal Heat Pump System for the New 500-bed 200,000 SF Student Housing

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Project at the University at Albanys Main Campus | Department of Energy Heat Pump System for the New 500-bed 200,000 SF Student Housing Project at the University at Albanys Main Campus Geothermal Heat Pump System for the New 500-bed 200,000 SF Student Housing Project at the University at Albanys Main Campus This project proposes to heat and cool planned 500-bed apartment-style student housing with closed loop vertical bore geothermal heat pump system installation.

  1. Issues surrounding the use of nickel-copper alloy K-500 fasteners in seawater

    SciTech Connect (OSTI)

    Natishan, M.E.; Porr, W.C. Jr.

    1994-12-31

    Nickel-copper alloy K-500 has long been used for the manufacture of fasteners for seawater applications. Alloy K-500 is a nickel-copper solid solution, precipitation strengthened with fine gamma prime precipitates to give it high strength, toughness and good general corrosion resistance. As the use of K-500 has increased in seawater, specifically in seawater tanks protected with anodes, its susceptibility to hydrogen embrittlement has come to light. Several recent failures in air suggest other rate-dependent failures mechanisms for this alloy that must be considered in fastener applications. These failure mechanisms and their interactions will be discussed.

  2. EERE Success Story-SunShot-funded Advanced Inverter Testing Enables 2,500

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Solar Energy Systems to Connect to Hawaii's Electric Grid | Department of Energy SunShot-funded Advanced Inverter Testing Enables 2,500 Solar Energy Systems to Connect to Hawaii's Electric Grid EERE Success Story-SunShot-funded Advanced Inverter Testing Enables 2,500 Solar Energy Systems to Connect to Hawaii's Electric Grid January 22, 2015 - 3:45pm Addthis Thanks to a SunShot collaboration at the Energy Department's National Renewable Energy Laboratory (NREL) more than 2,500 Hawaiian

  3. Word Pro - Untitled1

    U.S. Energy Information Administration (EIA) Indexed Site

    Kingdom 569 295 249 160 75 58 49 39 34 30 16 15 Mexico Canada Netherlands Brazil Japan Spain France Italy United Belgium U.S. Virgin South 0 100 200 300 400 500 600 Thousand ...

  4. Geothermal Regulatory Roadmap

    Broader source: Energy.gov (indexed) [DOE]

    ... Workshop FY12 Project Schedule 7 | US DOE Geothermal Office eere.energy.gov OpenEI (Open Energy Information) 0 100 200 300 400 500 600 700 800 900 1000 Aug-12 Sep-12 Oct-12 Nov-12 ...

  5. C:\\ANNUAL\\Vol2chps.v8\\ANNUAL2.VP

    U.S. Energy Information Administration (EIA) Indexed Site

    in the United States, 1930-2000 Figure 1930 1935 1940 1945 1950 1955 1960 1965 1970 1975 1980 1985 1990 1995 2000 0 5 10 15 20 25 0 100 200 300 400 500 600 700 Trillion Cubic...

  6. Stress-corrosion cracking of Inconel alloy 600 in high-temperature water: an update. [PWR

    SciTech Connect (OSTI)

    Bandy, R.; van Rooyen, D.

    1983-01-01

    Inconel 600 has been tested in high-temperature aqueous media (without oxygen) in several tests. Data are presented to relate failure times to periods of crack initiation and propagation. Quantitative relationships have been developed from tests in which variations were made in temperature, applied load, strain rate, water chemistry, and the condition of the test alloy.

  7. A study of the mechanism of primary water stress corrosion cracking of Alloy 600

    SciTech Connect (OSTI)

    Gourgues, A.F.; Andrieu, E.; Scott, P.M.

    1995-12-31

    Two aspects of the mechanism of stress corrosion cracking of Alloy 600 in pressurized water reactors (PWR) primary water have been studied in detail. Results are presented showing that grain boundaries of Alloy 600 are embrittled to a depth of several microns by exposure to primary water in an unstressed condition. It has been established that this embrittlement is not reversible by high temperature degassing and cannot be directly due to hydrogen. The results seem to support the hypothesis that oxygen atom penetration of grain boundaries is possible. However, no evidence of formation of grain boundary gas bubbles or oxides has been found. It is envisaged that this embrittlement process could sequentially act at the tip of a growing stress corrosion crack. The second phenomenon under study has been the plastic deformation behavior of Alloy 600 since it is known that cold work and stress have an important effect on stress corrosion cracking sensitivity. Results of plastic deformation during cyclic straining at various controlled strain rates are presented showing that Alloy 600 is not very sensitive to loading history and that cold work is of an essentially kinematic nature.

  8. Laser Peening of Alloy 600 to Improve Intergranular Stress Corrosion Cracking Resistance in Power Plants

    SciTech Connect (OSTI)

    Chen, H; Rankin, J; Hackel, L; Frederick, G; Hickling, J; Findlan, S

    2004-04-20

    Laser peening is an emerging modern process that impresses a compressive stress into the surface of metals or alloys. This treatment can reduce the rate of intergranular stress corrosion cracking and fatigue cracking in structural metals or Alloy 600 needed for nuclear power plants.

  9. Lead-induced stress corrosion cracking of Alloy 600 and 690 in high temperature water

    SciTech Connect (OSTI)

    Sakai, T.; Senjuh, T.; Aoki, K.; Shigemitsu, T.; Kishi, Y.

    1992-12-31

    Lead is one of the potential contributing impurities to the degradation of PWR steam generator tubing. Recent laboratory testing has shown that lead is a corrosive material for Alloy 600 steam generator tubing. However, it is still unknown how lead influences the corrosion of steam generator tubing, including the effect of lead concentration, solution pH, stress level and material characteristics. In this study, two kinds of experiments were performed. One was to investigate the thin film characteristic and selectively dissolved base metal elements of Alloy 600MA in high temperature solutions of different lead concentrations and pH. The other investigated the dependency of degradation of Alloy 600MA and Alloy 690TT on lead concentration and stress level in mild acidic environment, at 340{degrees}C for 2500 hrs. It was firstly demonstrated that lead-enhanced selective dissolution of nickel from alloy base metal, as a result of electrochemical reaction between lead and nickel, might cause the initiation and propagation of corrosion. Secondly, we showed that Alloy 690TT, generally very corrosion resistant material, also suffered from Pb-induced corrosion. The difference of the lead-induced stress corrosion morphology of Alloy 600MA and Alloy 690TT was also clarified.

  10. Investigation of the EAS Lateral Particle Density at 500 m Distance from Shower Core

    SciTech Connect (OSTI)

    Toma, G.

    2008-01-24

    For the experimental conditions of the KASCADE-Grande experiment, the density of EAS charged particles at the distance of about 500 m from the shower core S(500) has been shown by detailed simulation studies to be an approximate energy estimator, being nearly independent of the mass of the primary particle. This report presents some experimentally observed features of the S(500) observable registered with the KASCADE-Grande array installed at the Forschungszentrum Karlsruhe, Germany The measured energy deposits of particles in the 37 scintillation detector stations have been used to reconstruct the lateral charged particle distributions that are described by a Linsley parameterization (LDF). Among other features, the S(500) dependence from the EAS angle of incidence has been studied.

  11. NREL Employees and Managing Partner Pledge $500,000 to Aid Area Charities -

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    News Releases | NREL Employees and Managing Partner Pledge $500,000 to Aid Area Charities 2013 charitable giving campaign surpasses previous giving record December 13, 2012 The employees of the National Renewable Energy Laboratory (NREL) and the Alliance for Sustainable Energy, LLC, have pledged more than $500,000 to support local charities during the lab's annual holiday giving campaign. NREL employees have committed more than $466,000 to the Partnership for Colorado, Mile High United Way

  12. Treasury, Energy Announce $500 Million in Awards for Clean Energy Projects

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    | Department of Energy $500 Million in Awards for Clean Energy Projects Treasury, Energy Announce $500 Million in Awards for Clean Energy Projects September 1, 2009 - 12:00am Addthis WASHINGTON- Marking a major milestone in the effort to spur private sector investments in clean energy and create new jobs for America's workers, Treasury Secretary Tim Geithner and Energy Secretary Steven Chu today announced $502 million in the first round of awards from an American Recovery and Reinvestment

  13. EERE Success Story-SunShot-Supported Company to Create 500 New Solar

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Manufacturing Jobs | Department of Energy Company to Create 500 New Solar Manufacturing Jobs EERE Success Story-SunShot-Supported Company to Create 500 New Solar Manufacturing Jobs October 2, 2015 - 10:03am Addthis Suniva employee doing quality assurance testing at its Georgia headquarters. Photo Courtesy: Suniva Suniva employee doing quality assurance testing at its Georgia headquarters. Photo Courtesy: Suniva SunShot awardee Suniva, a manufacturer of high efficiency crystalline silicone

  14. Department of Energy-funded Bioenergy Research Centers File 500th Invention

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Disclosure | Department of Energy Department of Energy-funded Bioenergy Research Centers File 500th Invention Disclosure Department of Energy-funded Bioenergy Research Centers File 500th Invention Disclosure March 7, 2016 - 2:47pm Addthis News release from Oak Ridge National Laboratory and the Great Lakes Bioenergy Research Center OAK RIDGE, Tenn., March 3, 2016-Three U.S. Department of Energy-funded research centers - the BioEnergy Science Center (Oak Ridge National Laboratory), the Great

  15. INDEPENDENT TECHNICAL REVIEW OF THE C-400 INTERIM REMEDIAL PROJECT PHASE I RESULTS, PADUCAH, KENTUCKY

    SciTech Connect (OSTI)

    Looney, B.; Rossabi, J.; Stewart,L.; Richards, W.

    2010-10-29

    The groundwater and soil in the vicinity of the C-400 Building at the Paducah Gaseous Diffusion Plant (PGDP), is contaminated with substantial quantities of industrial solvents, primarily trichoroethene (TCE). This solvent 'source' is recognized as a significant challenge and an important remediation target in the overall environmental cleanup strategy for PGDP. Thus, the cleanup of the C-400 TCE Source is a principal focus for the Department of Energy (DOE) and its contractors, and for PGDP regulators and stakeholders. Using a formal investigation, feasibility study and decision process, Electrical Resistance Heating (ERH) was selected for the treatment of the soil and groundwater in the vicinity of C-400. ERH was selected as an interim action to remove 'a significant portion of the contaminant mass of TCE at the C-400 Cleaning Building area through treatment' with the longer term goal of reducing 'the period the TCE concentration in groundwater remains above its Maximum Contaminant Level (MCL).' ERH is a thermal treatment that enhances the removal of TCE and related solvents from soil and groundwater. The heterogeneous conditions at PGDP, particularly the high permeability regional gravel aquifer (RGA), are challenging to ERH. Thus, a phased approach is being followed to implement this relatively expensive and complex remediation technology. Conceptually, the phased approach encourages safety and efficiency by providing a 'lessons learned' process and allowing appropriate adjustments to be identified and implemented prior to follow-on phase(s) of treatment. More specifically, early deployment targeted portions of the challenging RGA treatment zone with relatively little contamination reducing the risk of adverse collateral impacts from underperformance in terms of heating and capture. Because of the importance and scope of the C-400 TCE source remediation activities, DOE chartered an Independent Technical Review (ITR) in 2007 to assess the C-400 ERH plans prior

  16. Stress corrosion cracking of Alloy 600 and Alloy 690 in all volatile treated water at elevated temperatures. Final report. [PWR

    SciTech Connect (OSTI)

    Theus, G.J.; Emanuelson, R.H.

    1983-05-01

    This report describes a continuing study of stress corrosion cracking (SCC) of Inconel alloys 600 and 690 in all-volatile treated (AVT) water. Specimens of alloys 600 and 690 are being exposed to AVT water at 288/sup 0/, 332/sup 0/, 343/sup 0/, and 360/sup 0/C. Alloy 600 generally resists SCC in high-purity water under normal service conditions but is susceptible under other specific conditions. In general, mill-annealed alloy 600 is more susceptible than stress-relieved material. Susceptibility to SCC increases rapidly with increasing exposure temperature. Very high stresses (near or above yield) are required to induce cracking in AVT or other high-purity waters. Most of the data presented in this report are for alloy 600; alloy 690 has not yet cracked. However, the program is being continued and will subsequently characterize the high-purity water cracking behavior, if any, of alloy 690.

  17. Data summary for nominal 500 ?m DUO2 Kernels

    SciTech Connect (OSTI)

    Hunn, John D

    2004-04-01

    This document is a compilation of characterization data obtained on the nominal 500 {micro}m DUO{sub 2} kernels produced by ORNL for the Advanced Gas Reactor Fuel Development and Qualification Program to satisfy the FY03 WBS 3.1.2 task milestone No.2.2 kg of kernels were produced and combined in two composite lots. DUN-500 was a 1630 g composite sieved between 500 {+-} 2 {micro}m and 534 {+-} 2 {micro}m ASTM E161 electroformed sieves. DUN-482 was a 385.6 g composite sieved between 482 {+-} 2 {micro}m and 518 {+-} 2 {micro}m ASTM E161 electroformed sieves. Size, shape, density, and microstructural analysis were performed on a 100 g sublot (DUN-500-S-1) riffled from the DUN-500 composite. Size and shape were also measured on a 100 g sublot (DUN-482-S-1) riffled from the DUN-482 composite. For comparison, analysis was also performed on kernels extracted from the German reference fuel EUO 2358-2365 (AGR-06).

  18. Application for Presidential Permit OE Docket No. PP-400 TDI-NE - New

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    England Clean Power Link Project - Comments and Motion to Intervene of Conservation Law Foundation | Department of Energy - New England Clean Power Link Project - Comments and Motion to Intervene of Conservation Law Foundation Application for Presidential Permit OE Docket No. PP-400 TDI-NE - New England Clean Power Link Project - Comments and Motion to Intervene of Conservation Law Foundation Conservation Law Foundation (CLF) provides the following comments and Motion to Intervene regarding

  19. Application for Presidential Permit OE Docket No. PP-400 TDI-NE - New

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    England Clean Power Link Project: Comments and Motion to Intervene Out of Time of Allco Renewable Energy Limited | Department of Energy - New England Clean Power Link Project: Comments and Motion to Intervene Out of Time of Allco Renewable Energy Limited Application for Presidential Permit OE Docket No. PP-400 TDI-NE - New England Clean Power Link Project: Comments and Motion to Intervene Out of Time of Allco Renewable Energy Limited ALLCO Renewable Energy Limited provides the following

  20. Application for Presidential Permit OE Docket No. PP-400 TDI-NE - New

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    England Clean Power Link Project: Federal Register Notice, Volume 79, No. 131 - July 9, 2014 | Department of Energy - New England Clean Power Link Project: Federal Register Notice, Volume 79, No. 131 - July 9, 2014 Application for Presidential Permit OE Docket No. PP-400 TDI-NE - New England Clean Power Link Project: Federal Register Notice, Volume 79, No. 131 - July 9, 2014 Application from TDI-NE to construct, operate and maintain electric transmission facilities at the U.S. - Canada

  1. Stress-corrosion cracking of Inconel alloy 600 in high-temperature water - an update

    SciTech Connect (OSTI)

    Bandy, R.; Van Rooyen, D.

    1984-08-01

    An experimental program on stress corrosion cracking (SCC) aimed at the development of a quantitative model for predicting the behavior of Inconel 600 tubing in high temperature water is described. Empirical data are gathered to relate factors that influence SCC. Work involves U-bends, constant extension rate tests (CERT), and constant load. Plots are made of failure time and crack velocity vs temperature, and also of SCC time vs stress, using a variety of environments related to the ingredients of primary or secondary water. Cold work of Alloy 600 is also included. The effect of temperature is found to yield-semi-log (Arrhenius) curves, and log-log plots of failure time vs stress are presented. Curves of this type are being evaluated for use in extrapolating accelerated test data to operating conditions for predictive purposes. 5 references, 8 figures, 3 tables.

  2. Stress corrosion crack detection in alloy 600 in high temperature caustic. Master`s thesis

    SciTech Connect (OSTI)

    Brisson, B.W.

    1996-06-01

    Alloy 600, the material used for pressurized water reactor steam generator tubing, is susceptible to environmentally assisted stress corrosion cracking. Intergranular stress corrosion cracking (IGSCC) attacks the tubes in areas of high residual stress, and in crevice regions. No method has been successfully developed to monitor steam generator tubing in-situ for crack initiation and growth. Essentially all available published IGSCC crack growth data for alloy 600 is based on non-tubing material. Although it is very likely that the current data base is applicable to tubing processing, differences between tube and other geometries make a comparison between tubing and other data important for verification purposes. However, obtaining crack initiation and growth data from tubing is difficult due to the geometry and the thin wall thickness.

  3. About the mechanism of stress corrosion cracking of Alloy 600 in high temperature water

    SciTech Connect (OSTI)

    Rebak, R.B.; Szklarska-Smialowska, Z.

    1995-12-31

    Alloy 600 is a material commonly used to construct the tubing in the steam generators (SG) of pressurized light water reactors (PWR) and of CANDU heavy water reactors. It is well established which variables and to which extent they influence the crack growth rate (CGR) in Alloy 600 exposed to high temperature (deaerated) water (HTW), especially in very aggressive conditions. There is evidence that the same variables that influence CGR also control the crack induction time. However, there are only a few data on crack induction time and no detailed explanation of the events that lead to the nucleation of a crack on an apparent smooth tube surface. In this paper, a critical review of the mechanisms of stress corrosion cracking (SCC) is given and, an interpretation of the events occurring during the long ({approx} 15 y) induction times observed in plant is postulated.

  4. Observations and insights into Pb-assisted stress corrosion cracking of alloy 600 steam generator tubes

    SciTech Connect (OSTI)

    Thomas, L.; Bruemmer, Stephen M.

    2005-08-15

    Pb-assisted stress-corrosion cracking (PbSCC) of Alloy 600 steam-generator tubing in high-temperature-water service and laboratory tests were studied by analytical transmission electron microscopy of cross-sectioned samples. Examinations of pulled tubes from many pressurized water reactors revealed lead in cracks from 11 of 17 samples. Comparisons of the degraded intergranular structures with ones produced in simple laboratory tests with PbO in near-neutral AVT water showed that the PbSCC characteristics in service tubing could be reproduced without complex chemistries and heat-flow conditions that can occur during plant operation. Observations of intergranular and transgranular cracks promoted by Pb in the test samples also provided new insights into the mechanisms of PbSCC in mill-annealed and thermally treated Alloy 600.

  5. Critical analysis of alloy 600 stress corrosion cracking mechanisms in primary water

    SciTech Connect (OSTI)

    Rios, R. |; Noel, D.; Bouvier, O. de; Magnin, T.

    1995-04-01

    In order to study the mechanisms involved in the stress-corrosion cracking (SCC) of Alloy 600 in primary water, the influence of the relevance of physicochemical and metallurgical parameters was assessed: hydrogen and oxygen overpressures, microstructure, and local chemical composition. The obtained results show that, even if the dissolution/oxidation seems to be the first and necessary step responsible for crack initiation and if hydrogen effects can also be involved in cracking, neither a dissolution/oxidation model nor a hydrogen model appears sufficient to account for cracking. Moreover, fractographic examinations performed on specimens` fracture surfaces lead to the fact that attention should be paid to a cleavage like microcracking mechanism involving interactions between corrosion and plasticity at the vicinity of grain boundaries. A corrosion-enhanced plasticity model is proposed to describe the intergranular and transgranular cracking in Alloy 600.

  6. State waste discharge permit application 400 Area secondary cooling water. Revision 2

    SciTech Connect (OSTI)

    1996-01-01

    This document constitutes the Washington Administrative Code 173-216 State Waste Discharge Permit Application that serves as interim compliance as required by Consent Order DE 91NM-177, for the 400 Area Secondary Cooling Water stream. As part of the Hanford Federal Facility Agreement and Consent Order negotiations, the US Department of Energy, Richland Operations Office, the US Environmental Protection Agency, and the Washington State Department of Ecology agreed that liquid effluent discharges to the ground on the Hanford Site that affect groundwater or have the potential to affect groundwater would be subject to permitting under the structure of Chapter 173-216 of the Washington Administrative Code, the State Waste Discharge Permitting Program. As a result of this decision, the Washington State Department of Ecology and the US Department of Energy, Richland Operations Office entered into Consent Order DE 91NM-177. The Consent Order DE 91NM-177 requires a series of permitting activities for liquid effluent discharges. Based upon compositional and flow rate characteristics, liquid effluent streams on the Hanford Site have been categorized into Phase 1, Phase 2, and Miscellaneous streams. This document only addresses the 400 Area Secondary Cooling Water stream, which has been identified as a Phase 2 stream. The 400 Area Secondary Cooling Water stream includes contribution streams from the Fuels and Materials Examination Facility, the Maintenance and Storage Facility, the 481-A pump house, and the Fast Flux Test Facility.

  7. Effect of silicon compounds on stress corrosion cracking of alloy 600 in caustic solutions

    SciTech Connect (OSTI)

    Navas, M.; Gomez-Briceno, D.; Garcia-Mazario, M.; McIlree, A.R.

    1999-07-01

    Silicon compounds are abundant in both steam generator tube deposits removed from operating plants and in the hideout return analyses performed during plant operation. Despite their abundance, the effect of these compounds on the susceptibility to intergranular attack (IGA) and stress corrosion cracking (SCC) of alloy 600 (UNS N06600) has not been established clearly in laboratory tests or under operating conditions. The present work studied the effect of different compounds of silicon, such as silica (SiO{sub 2}) and sodium metasilicate (Na{sub 2}SiO{sub 3}), on the susceptibility to IGA/SCC of alloy 600 in caustic solutions, with and without impurities. Experimental work included measurement of potentiodynamic polarization curves and development of stress corrosion tests with potentiostatic control at 315 C. Results of both tests indicated an inhibiting effect of silicon compounds on stress corrosion of mill-annealed (MA) alloy 600. Polarization curves in solutions with silicon compounds showed a wider range of passivation and a reduction in passive current density and anodic dissolution compared to the curves obtained in sodium hydroxide (NaOH). In corrosion tests performed in solutions containing silicon compounds, cracking appeared at only some of the potentials tested and with much reduced depth. Judging by the results obtained from analyses of the surface deposits, the inhibiting effect appeared to be related to the incorporation of silicon in the oxide layer. Regarding the effect of impurities, these have been observed not to be harmful for the response o alloy 600MA to IGA/SCC, and would appear even to improve this response in solutions containing silicon compounds, probably caused by the formation of insoluble silicates.

  8. Analysis of an AP600 intermediate-size loss-of-coolant accident

    SciTech Connect (OSTI)

    Boyack, B.E.; Lime, J.F.

    1995-09-01

    A postulated double-ended guillotine break of an AP600 direct-vessel-injection line has been analyzed. This event is characterized as an intermediate-break loss-of-coolant accident. Most of the insights regarding the response of the AP600 safety systems to the postulated accident are derived from calculations preformed with the TRAC-PF1/MOD2 code. However, complementary insights derived from a scaled experiment conducted in the ROSA facility, as well as insights based upon calculations by other codes, are also presented. Based upon the calculated and experimental results, the AP600 will not experience a core heat up and will reach a safe shutdown state using only safety-class equipment. Only the early part of the long-term cooling period initiated by In-containment Refueling Water Storage Tank injection was evaluated. Thus, the observation that the core is continuously cooled should be verified for the later phase of the long-term cooling period when sump injection and containment cooling processes are important.

  9. Stress corrosion cracking of alloy 600 using the constant strain rate test

    SciTech Connect (OSTI)

    Bulischeck, T. S.; van Rooyen, D.

    1980-01-01

    The most recent corrosion problems experienced in nuclear steam generators tubed with Inconel alloy 600 is a phenomenon labeled ''denting''. Denting has been found in various degrees of severity in many operating pressurized water reactors. Laboratory investigations have shown that Inconel 600 exhibits intergranular SCC when subjected to high stresses and exposed to deoxygenated water at elevated temperatures. A research project was initiated at Brookhaven National Laboratory in an attempt to improve the qualitative and quantitative understanding of factors influencing SCC in high temperature service-related environments. An effort is also being made to develop an accelerated test method which could be used to predict the service life of tubes which have been deformed or are actively denting. Several heats of commercial Inconel 600 tubing were procured for testing in deaerated pure and primary water at temperatures from 290 to 365/sup 0/C. U-bend type specimens were used to determine crack initiation times which may be expected for tubes where denting has occurred but is arrested and provide baseline data for judging the accelerating effects of the slow strain rate method. Constant extension rate tests were employed to determine the crack velocities experienced in the crack propagation stage and predict failure times of tubes which are actively denting. 8 refs., 17 figs., 5 tabs.

  10. Sensitization and SCC (stress corrosion cracking) study on thermally treated inconel 600

    SciTech Connect (OSTI)

    Kai, J-J.; Huang, T.A.; Tsai, C.H.

    1988-01-01

    Stress corrosion cracking (SCC) was recently discovered to be the major cause of failure in Inconel 600 used in steam generator (SG) tubes of pressurized water reactors (PWRs). The failure of the Three Mile Island SG tubes has been attributed to low-temperature SCC in the sulfur-contaminated environment under cold shutdown conditions. Bandy et al. found that even in the 10{sup {minus}6} M Na{sub 2}S{sub 2}O{sub 3} (or N{sub 2}S{sub 4}O{sub 6}) environment, the SCC would still be observable. This study investigates the effect of thermal treatment on the sensitization of Inconel 600 and studies the SCC behavior of this alloy in a sulfur-contaminated environment (S{sub 2}O{sub 3}{sup {minus}2}) using constant load test. The results of this study can be used to correlate the SCC susceptibility to the degree of sensitization of Inconel 600 by defining a critical chromium concentration under the test conditions.

  11. Conceptual design features of the Kalimer-600 sodium cooled fast reactor

    SciTech Connect (OSTI)

    Hahn, Dohee; Kim, Yeong-Il; Kim, Seong-O; Lee, Jae-Han; Lee, Yong-Bum; Jeong, Hae-Yong

    2007-07-01

    An advanced sodium cooled fast reactor concept, KALIMER-600, has been developed by the Korea Atomic Energy Research Institute to satisfy the Gen-IV technology goals of sustainability, safety and reliability, economics and proliferation resistance. The concept enables an efficient utilization of uranium resources and a reduction of the radioactive waste. The core design has been developed with a strong emphasis on a proliferation resistance by adopting a single enrichment fuel without blanket assemblies. In addition, a passive residual heat removal system, shortened intermediate heat-transport system piping and seismic isolation have been realized in the reactor system design as enhancements to its safety and economics. The inherent safety characteristics of the KALIMER-600 design were verified through a safety analysis of its bounding events. The results for various unprotected events imply that the KALIMER-600 design can accommodate all the analyzed ATWS events. This self-regulation capability of the power without a scram is mainly attributed to the inherent reactivity feedback mechanisms implemented in the metal fuel core design and completely passive decay heat removal system. (authors)

  12. Y-12 has almost 500 visitors from 23 states tour site during Secret City

    National Nuclear Security Administration (NNSA)

    Festival | National Nuclear Security Administration | (NNSA) has almost 500 visitors from 23 states tour site during Secret City Festival Wednesday, June 25, 2014 - 3:34pm NNSA Blog B&W Y-12 employee and tour guide Bill Wilburn, left, chats with Teresa Neas, and her husband Kim, whose mother, Audeane Bowers-Neas, worked at Y-12 in the 1940s. Tours of Y-12 on June 13 brought almost 500 visitors. Tourists from 23 states and the District of Columbia toured the site as part of Oak Ridge's

  13. Portsmouth/Paducah Employees, Contractors Donate 17,500 Pounds of Food |

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Department of Energy Portsmouth/Paducah Employees, Contractors Donate 17,500 Pounds of Food Portsmouth/Paducah Employees, Contractors Donate 17,500 Pounds of Food September 30, 2014 - 12:00pm Addthis EM and contractor staff of the Portsmouth Gaseous Diffusion Plant site prepare shipments of food to local pantries as part of the Portsmouth/Paducah Project Office’s 2014 Feds Feed Families effort. EM and contractor staff of the Portsmouth Gaseous Diffusion Plant site prepare shipments of

  14. Use of Static Compensators for Voltage Control at 330- and 500-kV Substations

    SciTech Connect (OSTI)

    Dement'ev, Yu. A.; Kochkin, V. I.; Idiatullov, R. M.; Papafanasopulo, S. G.; Smirnov, A. A.; Smirnov, S. G.

    2003-05-15

    A scheme for compensating the reactive power and controlling the voltage of high-voltage, intermediate-voltage, and low-voltage buses of 330 - 500-kV substations, which consist of static thyristor compensators (STC) on low-voltage autotransformers and controlled shunting reactors on high-voltage lines, is presented. It is shown that the STC can be created step-by-step beginning with the reactive part on substations with low-loaded lines. Results of installation of reactor groups of STC stepwise-controlled by vacuum switches at 330- and 500-kV substations are presented. Tests of the reactor groups have proved their high efficiency.

  15. EIS-0107: Mead-Phoenix +500-kV Direct Current Transmission Line

    Broader source: Energy.gov [DOE]

    The U.S. Department of Energy’s Western Area Power Administration (WAPA) prepared this statement to analyze the potential environmental and socioeconomic impacts arising from WAPA and regional project sponsors’ proposal to construct a 500 kilovolt (kV) alternating current (AC) transmission line with the capability to be upgraded later to 500kV direct current (DC), connecting the Westwing Substation, located north of Phoenix, Arizona, with a new McCullough II Substation, located approximately 14 miles west of Boulder City, Nevada. This statement modifies a previously prepared federal statement from which the participants' election to proceed had not occurred at the time this statement was prepared.

  16. Proposed amendment for Presidential Permit PP-63 and associated modifications to 500 kV international transmission line, Forbes, Minnesota to Manitoba, Canada Northern States Power Company. Final Environmental Assessment

    SciTech Connect (OSTI)

    Not Available

    1992-02-01

    Northern States Power Company, (NSP), a Minnesota investor owned utility has applied to the Office of Fossil Energy, United States Department of Energy, to amend Presidential Permit PP-63 to allow for alterations to the 500 kV transmission line and as sedated facilities currently regulated by this permit. The alterations proposed for the 500 kV line owned by NSP are part of a long term effort sponsored by NSP to upgrade the existing NSP transmission system to allow for increased exchange of electricity with the Manitoba Hydro-Electric Board. Presidential Permit PP-63 authorized NSP to construct, connect, operate and maintain a 500 kV line at the United States/Canadian border approximately seven-and-a-half miles west of Warroad in Roseau County, Minnesota. This line connects with a 500 kV line owned and operated by the Manitoba Hydro-Electric Board (MHEB), which extends from Dorsey, Manitoba, Canada to the United States/Canadian border. NSP proposes to increase the electricity transfer capability of this transmission facility by constructing a new 80-acre substation on the existing 500 kV line in Roseau County, Minnesota, and upgrading the existing substation at Forbes, Minnesota. The proposed Roseau substation would contain two 41.5 ohm series capacitor banks. In addition, static VAR compensators are to be installed at the existing Forbes Substation. Approximately 5 acres would be added to the 30-acre Forbes site to house the additional equipment. No new lines would enter or exit the facility. NSP proposes to place the new Roseau Substation in service in May 1993 and to complete the upgrading of the Forbes Substation in March 1994. The primary, initial purpose of these modifications is to enable NSP to import 400 megawatts of electric power from MHEB during the summer months to meet peak electrical demand in the Minneapolis-St. Paul area. It is expected that this power transfer would begin in 1993.

  17. Stress corrosion cracking of alloys 600 and 690 in all-volatile-treated water at elevated temperatures: Final report

    SciTech Connect (OSTI)

    Miglin, B.P.; Theus, G.J.

    1988-05-01

    This report describes stress corrosion (SCC) tests of Inconnel alloys 600 and 690 in all-volatile treated (AVT) water. Specimens of alloys 600 and 690 were exposed to AVT water at 288/degree/, 332/degree/, 343/degree/, and 360/degree/C. Alloy 660 generally resists SCC in high-purity water at normal sevice temperatures, but is susceptible to SCC at higher temperatures. In general, mill-annealed alloy 600 is more susceptible than high-treated material with fine lacy grain boundary carbides. Very high stresses (near or above yield) are required to induce cracking of alloy 600 in AVT or other high-purity waters. For alloy 600, 78 of 520 alloy 600 specimens eventually cracked. Although exposed for less total time than alloy 600 specimens, no alloy 690 specimens cracked. Three alloy 600 specimens cracked in the same autoclave tests in less time than those accumulated by the alloy 690 specimens. Longitudinally-oriented ID cracks became evident on alloy 690 split-tube U-bend specimens after autoclave exposures. These cracks on the 690 specimens were from three to ten times longer after exposure than similar defects found on unexposed alloy 690 specimens. The longitudinal crack lengthening on the alloy 690 split-tube U-bend specimens may have been a stress relaxation process or possibly a crack opening process of pre-existing, partially closed, longitudinal defects. Similar cracks were present in alloy 600 specimens, but in at least one case SCC did initiate from these shallow, blunt cracks.

  18. EIS-0118: Proposed Eugene-Medford 500-kV Transmission Line

    Broader source: Energy.gov [DOE]

    The U.S. Department of Interior developed this statement to assess the environmental impact of a proposed 500-kilovolt transmission line linking Eugene and Medford, Oregon, that would cross through public lands. The Bonneville Power Administration (BPA) would provide service to the proposed line and is a cooperating agency in the statement. BPA adopted the EIS on 7/10/1985.

  19. Scalar Meson {sigma}(500) Phase Motion at D+ {yields} {pi}-{pi}+{pi}+ Decay

    SciTech Connect (OSTI)

    Miranda, Jussara M. de; Bediaga, Ignacio

    2006-02-11

    Applying the Amplitude Difference Method to Fermilab experiment E791 D+ {yields} {pi}-{pi}+{pi}+ data, we measure the low mass {pi}+{pi}- phase motion. Our results suggest a significant phase variation, compatible with the existence of an isoscalar {sigma}(500) meson, as previously reported using an isobar model fit to the full Dalitz-plot density.

  20. The Case for a 500 GeV e+e- Linear Collider

    SciTech Connect (OSTI)

    Baggers, J.; Baltay, C.; Barker, T.; Barklow, T.; Bauer, U.; Bolton, T.; Brau, J.; Breidenbach, M.; Burke, D.; Burrows, P.; Dixon, L.; Fisk, H.E.; Frey, R.; Gerdes, D.; Graf, D.; Grannis, P.; Haber, H.E.; Hearty, C.; Hertzbach, S.; Heusch, C.; Hewett, J.; Hollebeek, R.; Jacobsen, R.; Jaros, J.; Kamon, T.; Karlen, D.; Koltick, D.; Kronfeld, A.; Marciano, W.; Markiewicz, T.; Murayama, H.; Nauenberg, U.; Orr, L.; Paige, F.; Para, A.; Peskin, M. E.; Porter, F.; Riles, K.; Ronan, M.; Rosenberg, L.; Schumm, B.; Stroynowski, R.; Tkaczyk, S.; Turcot, A.S.; van Bibber, K.; van Kooten, R.; Wells, J.D.; Yamamoto, H.

    2000-07-05

    Several proposals are being developed around the world for an e+e- linear collider with an initial center of mass energy of 500 GeV. In this paper, we will discuss why a project of this type deserves priority as the next major initiative in high energy physics.

  1. Lattice QCD Thermodynamics : 10k analysis with 1k thermalziation and block size of 500.

    SciTech Connect (OSTI)

    Soltz, R; Vranas, P; Gupta, R

    2007-05-10

    This is a re-analysis of the Lattice QCD Thermodynamics p4rhcm new beta analysis (UCRL-TR-230742) with approximately 10k trajectories per beta point, rerun with thermalization cut at 1000, and a block size of 500. Some diagnostic text has been omitted to reduce the number of pages.

  2. Residual Nuclei Production in the reaction {sup 136}Xe+ deuterium at 500 A MeV

    SciTech Connect (OSTI)

    Alcantara-Nunez, J. A.; Benlliure, J.; Perez-Loureiro, D.; Casarejos, E.; Fernandez Ordonez, M.; Pereira, J.; Armbruster, P.; Enqvist, T.; Henzl, V.; Henzlova, D.; Kelic, A.; Pleskac, R.; Ricciardi, M. V.; Schmidt, K.-H.; Schmitt, C.; Yordanov, O.; Audouin, L.; Bernas, M.; Lafriaskh, A.; Stephan, C.

    2010-04-26

    More than six hundred nuclei produced in the fragmentation of {sup 136}Xe projectiles at 500 A MeV on a liquid deuterium target were identified using inverse kinematics at the GSI Fragment Separator (FRS). These data are relevant for understanding of spallation reactions.

  3. THE CASE FOR A 500 GEV E+E- LINEAR COLLIDER

    SciTech Connect (OSTI)

    BAGGER,J.; BALTAY,C.; ET AL; MARCIANO,W.; PAIGE,F.; TURCOT,A.S.; AMERICAN LINEAR COLLIDER WORKING GROUP

    2000-06-30

    There are now several proposals that have been put forward from around the world for an e{sup +}e{sup {minus}} linear collider with an initial center of mass energy of 500 GeV. In this paper, the authors discuss why a project of this type deserves priority as the next, major initiative in high energy physics.

  4. Modeling and Simulations for the High Flux Isotope Reactor Cycle 400

    SciTech Connect (OSTI)

    Ilas, Germina; Chandler, David; Ade, Brian J; Sunny, Eva E; Betzler, Benjamin R; Pinkston, Daniel

    2015-03-01

    A concerted effort over the past few years has been focused on enhancing the core model for the High Flux Isotope Reactor (HFIR), as part of a comprehensive study for HFIR conversion from high-enriched uranium (HEU) to low-enriched uranium (LEU) fuel. At this time, the core model used to perform analyses in support of HFIR operation is an MCNP model for the beginning of Cycle 400, which was documented in detail in a 2005 technical report. A HFIR core depletion model that is based on current state-of-the-art methods and nuclear data was needed to serve as reference for the design of an LEU fuel for HFIR. The recent enhancements in modeling and simulations for HFIR that are discussed in the present report include: (1) revision of the 2005 MCNP model for the beginning of Cycle 400 to improve the modeling data and assumptions as necessary based on appropriate primary reference sources HFIR drawings and reports; (2) improvement of the fuel region model, including an explicit representation for the involute fuel plate geometry that is characteristic to HFIR fuel; and (3) revision of the Monte Carlo-based depletion model for HFIR in use since 2009 but never documented in detail, with the development of a new depletion model for the HFIR explicit fuel plate representation. The new HFIR models for Cycle 400 are used to determine various metrics of relevance to reactor performance and safety assessments. The calculated metrics are compared, where possible, with measurement data from preconstruction critical experiments at HFIR, data included in the current HFIR safety analysis report, and/or data from previous calculations performed with different methods or codes. The results of the analyses show that the models presented in this report provide a robust and reliable basis for HFIR analyses.

  5. Application for Presidential Permit OE Docket No. PP-400 TDI-NE New England

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Clean Power Link Project: Comments and Motion to Intervene Out of Time of Allco Renewable Energy Limited from TDI | Department of Energy New England Clean Power Link Project: Comments and Motion to Intervene Out of Time of Allco Renewable Energy Limited from TDI Application for Presidential Permit OE Docket No. PP-400 TDI-NE New England Clean Power Link Project: Comments and Motion to Intervene Out of Time of Allco Renewable Energy Limited from TDI TDI offers their response to Allco

  6. Equation of State for Supercooled Water at Pressures up to 400 MPa

    SciTech Connect (OSTI)

    Holten, Vincent; Sengers, Jan V.; Anisimov, Mikhail A.

    2014-12-01

    An equation of state is presented for the thermodynamic properties of cold and supercooled water. It is valid for temperatures from the homogeneous ice nucleation temperature up to 300 K and for pressures up to 400 MPa, and can be extrapolated up to 1000 MPa. The equation of state is compared with experimental data for the density, expansion coefficient, isothermal compressibility, speed of sound, and heat capacity. Estimates for the accuracy of the equation are given. The melting curve of ice I is calculated from the phase-equilibrium condition between the proposed equation and an existing equation of state for ice I.

  7. Volume Reflection Dependence of 400 GeV/c Protons on the Bent Crystal Curvature

    SciTech Connect (OSTI)

    Scandale, W.; Vomiero, A.; Baricordi, S.; Dalpiaz, P.; Fiorini, M.; Guidi, V.; Mazzolari, A.; Milan, R.; Della Mea, Gianantonio; Ambrosi, G.; Zuccon, P.; Bertucci, B.; Burger, W. J.; Duranti, M.; Cavoto, G.; Santacesaria, R.; Valente, P.; Iacoangeli, F.; Pisano, S.; Luci, C.

    2008-12-05

    The trend of volume reflection parameters (deflection angle and efficiency) in a bent (110) silicon crystal has been investigated as a function of the crystal curvature with 400 GeV/c protons on the H8 beam line at the CERN Super Proton Synchrotron. This Letter describes the analysis performed at six different curvatures showing that the optimal radius for volume reflection is approximately 10 times greater than the critical radius for channeling. A strong scattering of the beam by the planar potential is also observed for a bend radius close to the critical one.

  8. Stress relief treatment of Alloy 600 steam generator tubing. Final report

    SciTech Connect (OSTI)

    van Rooyen, D.; Cragnolino, C.

    1994-01-01

    The intergranular stress corrosion cracking (IGSCC) of Alloy 600 tubing in the primary side of operating steam generators is the subject of this investigation. The objective of the program was to examine the feasibility of heat treatment to alleviate the IGSCC problem. In addition to this, tests were also performed to examine the IGSCC susceptibility of nuclear grade Alloy 600 tubing obtained from various sources. Examination of temperature-time combinations that may hold potential for improved IGSCC resistance of the transition regions of tubes expanded into tube sheet holes was done. The combinations fall in two categories. One is of short duration and relatively high temperature, where induction is the best method of heating because the treatment only lasts from some tens of seconds to a few minutes. The other is carried out in a lower temperature range and lasts for several hours. This latter combination of temperatures and times is considered for the so-called global heat treatment of entire tube sheet. To assess the effect of these treatments, reverse U-bend testing in high purity deaerated water containing an overpressure of hydrogen was employed and several heats of Alloy 600 were compared in tests at 365{degrees}C, which is well above actual operating temperatures of steam generators, but provides an accelerated test procedure. Results of furnace heating in the range of 550-610{degrees}C indicated improvement in IGSCC resistance, with best performance after a heat treatment at 610{degrees}C for nine hours. In addition to stress relief, carbide precipitation can also occur, and their relative contributions to the improvement is discussed.

  9. Fact #600: December 7, 2009 China Produced More Vehicles than the U.S. in

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    2008 | Department of Energy 0: December 7, 2009 China Produced More Vehicles than the U.S. in 2008 Fact #600: December 7, 2009 China Produced More Vehicles than the U.S. in 2008 In 1980, the U.S. produced 56 times more vehicles than China. China's vehicle production has been growing since then, while U.S. vehicle production was hit hard in the recent economic downturn. In the year 2008, China produced 9.5 million vehicles, while the U.S. produced 8.7 million vehicles. Vehicles Produced in

  10. Results of Remediation and Verification Sampling for the 600-270 Horseshoe Landfill

    SciTech Connect (OSTI)

    W. S. Thompson

    2005-12-14

    This report presents the results of the 2005 remedial action and verification soil sampling conducted at the 600-270 waste site after removal of soil containing residual concentrations of dichlorodiphenyl trichloroethane and its breakdown products dichlorodiphenyl dichloroethylene and dichlorodiphenyl dichloroethane. The remediation was performed in response to post-closure surface soil sampling performed between 1998 and 2003 that indicated the presence of residual DDT contamination exceeding the Record of Decision for the 1100 Area National Priorities List site cleanup criteria of 1 mg/kg that was established for the original 1994 cleanup activities.

  11. Un~ted States Environmental Monltorlng EPA/600/4-86/022 Env~ronmental Protection

    Office of Legacy Management (LM)

    Environmental Monltorlng EPA/600/4-86/022 Env~ronmental Protection Systems Laboratory DOE/DP/00539/056 Agency P.0 Box 15027 A p r ~ l 1986 Las Vegas NV 891 14-5027 3 Research and Development Off -Site Environmental Monitoring Report: Radiation Monitoring Around United States Nuclear Test Areas, Calendar Year prepared for the United States Department of Energy under Interagency Agreement Number DE-AI08-76DP00539 This page intentionally left blank EPA-60014-86-022 DOE/DP/00539-056 April 1986

  12. In-situ stress relief of expanded Alloy 600 steam generator tubing

    SciTech Connect (OSTI)

    Woodward, J.; van Rooyen, D.; McIlree, A.R.

    1984-01-01

    Stress corrosion cracking is the most common cause of defects in steam generator tubing. Methods of averting tubing damage are constantly under review. This paper concentrates on the problem of intergranular stress corrosion cracking, initiated on the primary side, in the expansion transition region of roller expanded Alloy 600 tubing. In general it is believed that residual stresses, arising from the expansion process, are the cause of the problem. The work reported here discusses the identification and implementation of an optimal, in-situ stress relief treatment.

  13. Stress corrosion cracking of Alloy 600 using the constant strain rate test

    SciTech Connect (OSTI)

    Bulischeck, T.S.; Van Rooyen, D.

    1981-10-01

    Nuclear grade production tubing of Alloy 600 was evaluated for stress corrosion cracking (SCC) susceptibility in high purity water at 365, 345, 325, and 290 C. Reverse tube U-bend specimens provided crack initiation data and constant extension rate tests were employed to determine the crack velocities experienced in th crack propagation stage. Initial results indicate that a linear extrapolation of data received from high temperature tests can be used to predict the service life of steam generator tubing that has been plastically deformed or is continually deforming by ''denting.''

  14. Characteristics of acoustic emission during stress corrosion cracking of Inconel 600 alloy

    SciTech Connect (OSTI)

    Sung, K.Y.; Kim, I.S.; Yoon, Y.K.

    1997-10-15

    It is possible to detect by use of the acoustic emission (AE) technique the dynamic processes in stressed materials. In this study, the AE technique is applied to SCC of Inconel 600 due to depletion of chromium at grain boundaries to investigate the AE capability of detecting crack growth and to obtain the relation between AE characteristics and crack mechanisms such as fracture mode and crack growth rate during SCC. In addition, the generation of initial cracks was detected, and minimum crack size detectable with AE was determined to assess the potential of AE as a non-destructive method.

  15. PDSF Office Hours 1/23/14 from 2:30 to 4:00 pm at LBNL

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    /23/14 from 2:30 to 4:00 pm at LBNL PDSF Office Hours 1/23/14 from 2:30 to 4:00 pm at LBNL January 22, 2014 PDSF office hours will be from 2:30 to 4:00 pm in 50B-2222 tomorrow. Subscribe via RSS Subscribe Browse by Date February 2014 January 2014 November 2013 October 2013 September 2013 August 2013 March 2012 February 2012 January 2012 October 2011 July 2011 May 2011 April 2011 March 2011 February 2011 January 2011 December 2010 Last edited: 2014-01-22 16:33:02

  16. Irradiation creep of various ferritic alloys irradiated {approximately}400 C in the PFR and FFTF reactors

    SciTech Connect (OSTI)

    Toloczko, M.B.; Garner, F.A.; Eiholzer, C.R.

    1998-03-01

    Three ferritic alloys were irradiated in two fast reactors to doses of 50 dpa or more at temperatures near 400 C. One martensitic alloy, HT9, was irradiated in both the FFTF and PFR reactors. PFR is the Prototype Fast Reactor in Dourneay, Scotland, and FFTF is the Fast Flux Test Facility in Richland, WA. D57 is a developmental alloy that was irradiated in PFR only, and MA957 is a Y{sub 2}O{sub 3} dispersion-hardened ferritic alloy that was irradiated only in FFTF. These alloys exhibited little or no void swelling at {approximately}400 C. Depending on the alloy starting condition, these steels develop a variety of non-creep strains early in the irradiation that are associated with phase changes. Each of these alloys creeps at a rate that is significantly lower than that of austenitic steels irradiated in the same experiments. The creep compliance for ferritic alloys in general appears to be {approximately}0.5 {times} 10{sup {minus}6} MPa{sup {minus}1} dpa{sup {minus}1}, independent of both composition and starting state. The addition of Y{sub 2}O{sub 3} as a dispersoid does not appear to change the creep behavior.

  17. The Stress Corrosion Crack Growth Rate of Alloy 600 Heat Affected Zones Exposed to High Purity Water

    SciTech Connect (OSTI)

    George A. Young; Nathan Lewis

    2003-04-05

    Grain boundary chromium carbides improve the resistance of nickel based alloys to primary water stress corrosion cracking (PWSCC). However, in weld heat affected zones (HAZ's), thermal cycles from fusion welding can solutionize beneficial grain boundary carbides, produce locally high residual stresses and strains, and promote PWSCC. The present research investigates the crack growth rate of an A600 HAZ as a function of test temperature. The A600 HAZ was fabricated by building up a gas-tungsten-arc-weld deposit of EN82H filler metal onto a mill-annealed A600 plate. Fracture mechanics based, stress corrosion crack growth rate testing was performed in high purity water between 600 F and 680 F at an initial stress intensity factor of 40 ksi {radical}in and at a constant electrochemical potential. The HAZ samples exhibited significant SCC, entirely within the HAZ at all temperatures tested. While the HAZ samples showed the same temperature dependence for SCC as the base material (HAZ: 29.8 {+-} 11.2{sub 95%} kcal/mol vs A600 Base: 35.3 {+-} 2.58{sub 95%} kcal/mol), the crack growth rates were {approx} 30X faster than the A600 base material tested at the same conditions. The increased crack growth rates of the HAZ is attributed to fewer intergranular chromium rich carbides and to increased plastic strain in the HAZ as compared to the unaffected base material.

  18. Results from Alloy 600 And Alloy 690 Caustic SCC Model Boiler Tests

    SciTech Connect (OSTI)

    Miller, Frederick D.; Thomas, Larry E.

    2009-08-03

    A versatile model boiler test methodology was developed and used to compare caustic stress corrosion cracking (SCC) of mill annealed Alloy 600 and thermally treated Alloy 690. The model boiler included simulated crevice devices that efficiently and consistently concentrated Na2CO3, resulting in volatilization of CO2 with the steam and concentration of NaOH at the tube surfaces. The test methodology also included variation in tube stress, either produced by the primary to secondary side pressure differential, or by a novel method that reproducibly yields a higher stress condition on the tube. The significant effect of residual stress on tube SCC was also considered. SCC of both Alloy 600 and Alloy 690 were evaluated as a function of temperature and stress. Analytical transmission electron microscopy (ATEM) evaluations of the cracks and the grain boundaries ahead of the cracks were performed, providing insight into the SCC mechanism. This model boiler test methodology may be applicable to a range of bulkwater secondary chemistries that concentrate to produce aggressive crevice environments.

  19. Stress corrosion cracking of alloy 600 in high temperature aqueous solutions: Influencing factors, mechanisms and models

    SciTech Connect (OSTI)

    Szklarska-Smialowska, Z.; Rebak, R.B.

    1996-12-31

    A detailed critical review of the multiple variables affecting stress corrosion cracking (SCC) of in high temperature (deaerated) aqueous solutions is given. Most of the data in the literature deals with the cracking susceptibility in the primary side; however, it is clear that similar factors and to a similar extent influence the SCC susceptibility in both primary and secondary sides. Some factors such as alkalinity of the solution or presence of lead (Pb) may be more in the secondary side and others such as partial pressure of hydrogen (H{sub 2}) in the primary side. Even though the effect of the variables on SCC susceptibility is more or less established, in models, in most of the cases there is a lack of fundamental understanding of the mechanisms involved. The different mechanisms and models proposed to explain the SCC of alloy 600 are briefly reviewed and their validity to explain the influence of the variables and to predict the crack growth rate (CGR), is assessed. It is concluded that several of the proposed models seem to give a fair estimate of the CGR values under certain conditions; however, it appears that a single mechanism cannot explain in detail the complex case of alloy 600 SCC. 113 refs., 11 figs., 3 tabs.

  20. Effect of heat treatment on caustic stress corrosion cracking behavior of alloy 600

    SciTech Connect (OSTI)

    Sung, J.K.

    1999-12-01

    Constant elongation rate tests (CERT) were conducted to evaluate the effect of heat treatment on intergranular stress corrosion cracking (IGSCC) susceptibility of alloy 600 (UNS NO6600) in 140 C and 50% caustic solution at {minus}900 mV vs saturated calomel electrode (SCE). Results showed: (1) Heat treatment at low temperature for a long time (600 C for 260 h) led to a material that was not susceptible to caustic intergranular (IG) cracking. Increase in heat treatment temperature enhanced IG cracking susceptibility. Caustic IGSCC susceptibility was at maximum near the carbon solubility limit. However, when the heat treatment temperature was higher than the carbon solubility limit, a significant decrease in crack growth rate was observed. (2) Grain boundaries acted as a preferential crack path when grain boundary carbon segregation was likely. Thermodynamic considerations suggested that severe caustic IGSCC susceptibility near the carbon solubility limit could be explained in terms of carbon segregation at the grain boundaries. (3) IGSCC in caustic solution did not seem to be caused by chromium depletion. (4) Although formation of semi-continuous IG carbides and IGSCC resistance seemed to exhibit a similar chronological response with heat treatment, it was unlikely that grain boundary IG carbides played a role in caustic IGSCC susceptibility.

  1. Assessment of an improved multiaxial strength theory based on creep-rupture data for Inconel 600

    SciTech Connect (OSTI)

    Huddleston, R.L.

    1993-06-01

    A new multiaxial strength theory incorporating three independent stress parameters was developed and reported by the author in 1984. It was formally incorporated into ASME Code Case N47-29 in 1990. The new theory provided significantly more accurate stress-rupture life predictions than obtained using the classical theories of von Mises, Tresca, and Rankins (maximum principal stress), for Types 304 and 316 stainless steel tested at 593 and 600{degrees}C respectively under different biaxial stress states. Additional results for Inconel 600 specimens tested at 816{degrees}C under tension-tension and tension-compression stress states are presented in this paper and show a factor of approximately 2.4 reduction in the scatter of predicted versus observed lives as compared to the classical theories of von Mises and Tresca and a factor of about 5 as compared to the Rankins theory. A key feature of the theory, which incorporates the maximum deviatoric stress, the first invariant of the stress tensor, and the second invariant of the deviatoric stress tensor, is its ability to distinguish between life under tensile versus compressive stress states.

  2. Ion-induced swelling of ODS ferritic alloy MA957 tubing to 500 dpa

    SciTech Connect (OSTI)

    Toloczko, Mychailo B.; Garner, F. A.; Voyevodin, V.; Bryk, V. V.; Borodin, O. V.; Melnichenko, V. V.; Kalchenko, A. S.

    2014-10-01

    In order to study the potential swelling behavior of the ODS ferritic alloy MA957 at very high dpa levels, specimens were prepared from pressurized tubes that were unirradiated archives of tubes previously irradiated in FFTF to doses as high at 110 dpa. These unirradiated specimens were irradiated with 1.8 MeV Cr+ ions to doses ranging from 100 to 500 dpa and examined by transmission electron microscopy. No coinjection of helium or hydrogen was employed. It was shown that compared to several ferritic/martensitic steels irradiated in the same facility, these tubes were rather resistant to void swelling, reaching a maximum value of only 4.5% at 500 dpa and 450°C. In this fine-grained material, the distribution of swelling was strongly influenced by the presence of void denuded zones along the grain boundaries.

  3. Non-ordinary nature of the f_0(500) resonance from its Regge trajectory

    SciTech Connect (OSTI)

    Nebreda, J.; Londergan, J. Timothy; Pelaez, J. R.; Szczepaniak, Adam P.

    2014-07-01

    We report our results on how to obtain the Regge trajectory of a resonance from its pole in a scattering process by imposing analytic constraints in the complex angular momentum plane. The method, suited for resonances that dominate an elastic scattering amplitude, has been applied to the {\\rho}(770) and the f_0(500) resonances. Whereas for the former we obtain a linear Regge trajectory, characteristic of ordinary quark-antiquark states, for the latter we find a non-linear trajectory with a much smaller slope at the resonance mass. Moreover, we show that if a linear trajectory with a slope of typical size is imposed for the f_0(500), the corresponding amplitude is at odds with the data. This provides a strong indication of the non-ordinary nature of the sigma meson.

  4. 17th Edition of TOP500 List of World's Fastest SupercomputersReseased

    SciTech Connect (OSTI)

    Strohmaier, Erich; Meuer, Hans W.; Dongarra, Jack J.; Simon,Horst D.

    2001-06-21

    17th Edition of TOP500 List of World's Fastest Supercomputers Released MANNHEIM, GERMANY; KNOXVILLE, TENN.; BERKELEY, CALIF. In what has become a much-anticipated event in the world of high-performance computing, the 17th edition of the TOP500 list of the world's fastest supercomputers was released today (June 21). The latest edition of the twice-yearly ranking finds IBM as the leader in the field, with 40 percent in terms of installed systems and 43 percent in terms of total performance of all the installed systems. In second place in terms of installed systems is Sun Microsystems with 16 percent, while Cray Inc. retained second place in terms of performance (13 percent). SGI Inc. was third both with respect to systems with 63 (12.6 percent) and performance (10.2 percent).

  5. EIS-0301: NRG Energy Services, Inc., Arizona-Baja California 500 kV Transmission Line

    Broader source: Energy.gov [DOE]

    This EIS analyzes DOE's decision to approve NRG Energy, Inc. (NRG) for a Presidential permit to construct a 500,000-volt transmission line originating at the switchyard of the Palo Verde Nuclear Generating Station near Phoenix, Arizona, and extending approximately 177 miles to the southwest, where it would cross the United States (U.S.) border with Mexico in the vicinity of Calexico, California.

  6. EIS-0091: Garrison-Spokane 500-kV Transmission Project

    Broader source: Energy.gov [DOE]

    The U.S. Department of Energy's Bonneville Power Administration (BPA) developed this statement to evaluate the environmental impacts of constructing between 254 and 271 miles of 500-kilovolt transmission line across western Montana and northern Idaho to the Spokane area in order to reinforce a section of the BPA electric power grid and to permit reliable integration of 1,240 megawatts of power produced by Colstrip Units 3 and 4, for use in Montana and throughout the Northwest.

  7. ATP for the portable 500 CFM exhauster POR-005 skid C

    SciTech Connect (OSTI)

    Keller, C.M.

    1997-06-27

    This Acceptance Test Plan is for a 500 CFM Portable Exhauster POR-005 to be used for saltwell pumping. The Portable Exhauster System will be utilized to eliminate potential flammable gases that may exist within the dome space of the tank. This Acceptance Plan will test and verify that the exhauster meets the specified design criteria, safety requirements, operations requirements, and will provide a record of the functional test results.

  8. ATP for the portable 500 CFM exhauster POR-004 skid B

    SciTech Connect (OSTI)

    Keller, C.M.

    1997-05-06

    This Acceptance Test Plan is for a 500 CFM Portable Exhauster POR-004 to be used for saltwell pumping. The Portable Exhauster System will be utilized to eliminate potential flammable gases that may exist within the dome space of the tank. This Acceptance Plan will test and verify that the exhauster meets the specified design criteria, safety requirements, operations requirements, and will provide a record of the functional test results.

  9. ATP for the portable 500 CFM exhauster POR-006 skid D

    SciTech Connect (OSTI)

    Keller, C.M.

    1997-07-29

    This Acceptance Test Plan is for a 500 CFM Portable Exhauster POR-006 to be used for saltwell pumping. The Portable Exhauster System will be utilized to eliminate potential flammable gases that may exist within the dome space of the tank. This Acceptance Plan will test and verify that the exhauster meets the specified design criteria, safety requirements, operations requirements, and will provide a record of the functional test results.

  10. Precipitation hardening in nickel-copper base alloy Monel K 500

    SciTech Connect (OSTI)

    Dey, G.K.; Tewari, R.; Wadekar, S.L.; Mukhopadhyay, P.; Rao, P.

    1993-12-01

    The occurrence of a significant amount of age hardening, due to the precipitation of the {gamma}{prime} phase, has been demonstrated in the nickel-copper base alloy MONEL K 500. The microstructure of the precipitation-hardened and deformed alloy has been examined in peak-aged, underaged and overaged conditions. An attempt has been made to compare the observed increments in strength in these three aged conditions to those predicted on the basis of relevant theoretical models.

  11. SEARCHING FOR THE HIGHEST REDSHIFT SOURCES IN 250-500 {mu}m SUBMILLIMETER SURVEYS

    SciTech Connect (OSTI)

    Pope, Alexandra; Chary, Ranga-Ram

    2010-06-01

    We explore a technique for identifying the highest redshift (z>4) sources in Herschel/SPIRE and BLAST submillimeter surveys by localizing the position of the far-infrared dust peak. Just as Spitzer/IRAC was used to identify stellar 'bump' sources, the far-IR peak is also a redshift indicator; although the latter also depends on the average dust temperature. We demonstrate the wide range of allowable redshifts for a reasonable range of dust temperatures and show that it is impossible to constraint the redshift of individual objects using solely the position of the far-IR peak. By fitting spectral energy distribution models to simulated Herschel/SPIRE photometry we show the utility of radio and/or far-infrared data in breaking this degeneracy. With prior knowledge of the dust temperature distribution it is possible to obtain statistical samples of high redshift submillimeter galaxy (SMG) candidates. We apply this technique to the BLAST survey of ECDFS to constrain the number of dusty galaxies at z>4. We find 8 {+-} 2 galaxies with flux density ratios of S {sub 500}>S {sub 350}; this sets an upper limit of 17 {+-} 4 deg{sup -2} if we assume all are at z>4. This is <35 % of all 500 {mu}m-selected galaxies down to S {sub 500}>45 mJy (L {sub IR}>2 x 10{sup 13} L {sub sun} for z>4). Modeling with conventional temperature and redshift distributions estimates the percentage of these 500 {mu}m peak galaxies at z>4 to be between 10% and 85%. Our results are consistent with other estimates of the number density of very high redshift SMGs and follow the decline in the star formation rate density at z>4.

  12. A Study of Electromagnetic Radiation of Corona Discharge Near 500-Kv Electric Installations

    SciTech Connect (OSTI)

    Korzhov, A. V.; Okrainskaya, I. S.; Sidorov, A. I.; Kufel'd, V. D.

    2004-01-15

    Data on the spectral composition and intensity of electromagnetic radiation of corona discharge are obtained in an experimental study performed on the outdoor switchgear of the Shagol 500-kV substation of the Chelyabinsk Enterprise of Trunk Transmission Grids and under a 500-kV Shagol - Kozyrevo overhead transmission line. The electromagnetic environment on the territory of the 500-kV outdoor switchgear is shown to be determined by narrow-band radiations (harmonics of the frequency of electric supply) and wide-band radiations due to corona discharges of high-voltage sources. This means that the personnel experience the action of a commercial-frequency electric field and electromagnetic radiation of a quite wide range, which is not allowed for by the existing guidelines. It is recommended to continue the study in cooperation with medical institutions in order to create guidelines that would allow for the joint action of commercial-frequency electric field and electromagnetic radiation and for the voltage in the line, the current load, the meteorological situation, and other factors.

  13. Specification for strontium-90 500-watt(e) radioisotopic thermoelectric generator. Final report

    SciTech Connect (OSTI)

    Hammel, T.; Himes, J.; Lieberman, A.; McGrew, J.; Owings, D.; Schumann, F.

    1983-04-01

    A conceptual design for a demonstration 500-watt(e) radioisotopic thermoelectric generator has been created for the Department of Energy. The design effort was divided into two tasks, viz., create a design specification for a capsule strength member that utilizes a standard Strontium-90 fluoride-filled WESF inner liner, and create a conceptual design for a 500-watt(e) RTG. Both tasks have been accomplished. The strength-member specification was designed to survive an external pressure of 24,500 psi and meet the requirements of special-form radioisotope heat sources. Therefore the capsule can, if desired, be licensed for domestic and international transport. The design for the RTG features a radioisotopic heat source, an array of nine capsules in a tungsten biological shield, four current-technology series-connected thermoelectric-conversion modules, low-conductivity thermal insulation, and a passive finned-housing radiator for waste-heat dissipation. The preliminary RTG specification formulated previous to contract award has been met or exceeded. The power source will generate the required power for the required service period at 28 volts dc with a conversion efficiency of 8%, provided the existing in-pool capsules at WESF meet the assumed thermal-inventory requirements.

  14. Molecular dynamics for 400 million particles with short-range interactions

    SciTech Connect (OSTI)

    Deng, Y.; McCoy, R.A.; Marr, R.B.

    1995-07-01

    We report the design and performance of a computational molecular dynamics (MD) code for 400 million particles interacting through the standard pairwise 6-12 Lennard-Jones potential on a 1024-node Intel Paragon, a distributed-memory MIMD parallel computer. The initially recorded {open_quotes}particle-step time{close_quotes} was .4 microseconds. A new inter-node communication strategy ensures high parallel efficiency for a large number of nodes. Besides the ability to tackle large problems, our implementation incorporates a novel method for dynamic load balancing. Our communication and load balancing enhancements provide increased efficiency and flexibility for our MD code. vet are general enough for use in other parallel algorithms.

  15. NEUTRON-INDUCED SWELLING OF Fe-Cr BINARY ALLOYS IN FFTF AT ~400 DEGREES C

    SciTech Connect (OSTI)

    Garner, Francis A.; Greenwood, Lawrence R.; Okita, Taira; Sekimura, Naoto; Wolfer, W. G.

    2002-12-31

    The purpose of this effort is to determine the influence of dpa rate, He/dpa ratio and composition on the void swelling of simple binary Fe-Cr alloys. Contrary to the behavior of swelling of model fcc Fe-Cr-Ni alloys irradiated in the same FFTF-MOTA experiment, model bcc Fe-Cr alloys do not exhibit a dependence of swelling on dpa rate at approximately 400 degrees C. This is surprising in that an apparent flux-sensitivity was observed in an earlier comparative irradiation of Fe-Cr binaries conducted in EBR-II and FFTF. The difference in behavior is ascribed to the higher helium generation rates of Fe-Cr alloys in EBR-II compared to that of FFTF, and also the fact that lower dpa rates in FFTF are accompanied by progressively lower helium generation rates.

  16. Test of a 1.8 Tesla, 400 Hz Dipole for a Muon Synchrotron

    SciTech Connect (OSTI)

    Summers, D.J.; Cremaldi, L.M.; Hart, T.L.; Perera, L.P.; Reep, M.; Witte, H.; Hansen, S.; Lopes, M.L.; Reidy Jr., J.; /Oxford High School

    2012-05-01

    A 1.8 T dipole magnet using thin grain oriented silicon steel laminations has been constructed as a prototype for a muon synchrotron ramping at 400 Hz. Following the practice in large 3 phase transformers and our own Opera-2d simulations, joints are mitred to take advantage of the magnetic properties of the steel which are much better in the direction in which the steel was rolled. Measurements with a Hysteresigraph 5500 and Epstein frame show a high magnetic permeability which minimizes stored energy in the yoke allowing the magnet to ramp quickly with modest voltage. Coercivity is low which minimizes hysteresis losses. A power supply with a fast Insulated Gate Bipolar Transistor (IGBT) switch and a capacitor was constructed. Coils are wound with 12 gauge copper wire. Thin wire and laminations minimize eddy current losses. The magnetic field was measured with a peak sensing Hall probe.

  17. Development of a Scale Model for High Flux Isotope Reactor Cycle 400

    SciTech Connect (OSTI)

    Ilas, Dan

    2012-03-01

    The development of a comprehensive SCALE computational model for the High Flux Isotope Reactor (HFIR) is documented and discussed in this report. The SCALE model has equivalent features and functionality as the reference MCNP model for Cycle 400 that has been used extensively for HFIR safety analyses and for HFIR experiment design and analyses. Numerical comparisons of the SCALE and MCNP models for the multiplication constant, power density distribution in the fuel, and neutron fluxes at several locations in HFIR indicate excellent agreement between the results predicted with the two models. The SCALE HFIR model is presented in sufficient detail to provide the users of the model with a tool that can be easily customized for various safety analysis or experiment design requirements.

  18. Response of 9Cr-ODS Steel to Proton Irradiation at 400 °C

    SciTech Connect (OSTI)

    Jianchao He; Farong Wan; Kumar Sridharan; Todd R. Allen; A. Certain; Y. Q. Wu

    2014-09-01

    The stability of Y–Ti–O nanoclusters, dislocation structure, and grain boundary segregation in 9Cr-ODS steels has been investigated following proton irradiation at 400 °C with damage levels up to 3.7 dpa. A slight coarsening and a decrease in number density of nanoclusters were observed as a result of irradiation. The composition of nanoclusters was also observed to change with a slight increase of Y and Cr concentration in the nanoclusters following irradiation. Size, density, and composition of the nanoclusters were investigated as a function of nanocluster size, specifically classified to three groups. In addition to the changes in nanoclusters, dislocation loops were observed after irradiation. Finally, radiation-induced enrichment of Cr and depletion of W were observed at grain boundaries after irradiation.

  19. INTERPRETATION OF AIRBORNE ELECTROMAGNETIC AND MAGNETIC DATA IN THE 600 AREA

    SciTech Connect (OSTI)

    CUMMINS GD

    2010-11-11

    As part of the 200-PO-1 Phase I geophysical surveys, Fugro Airborne Surveys was contracted to collect airborne electromagnetic (EM) and magnetic surveys of the Hanford Site 600 Area. Two helicopter survey systems were used with the HeliGEOTEM{reg_sign} time domain portion flown between June 19th and June 20th, 2008, and the RESOLVE{reg_sign} frequency domain portion was flown from June 29th to July 1st, 2008. Magnetic data were acquired contemporaneously with the electromagnetic surveys using a total-field cesium vapor magnetometer. Approximately 925 line kilometers (km) were flown using the HeliGEOTEM{reg_sign} II system and 412 line kilometers were flown using the RESOLVE{reg_sign} system. The HeliGEOTEM system has an effective penetration of roughly 250 meters into the ground and the RESOLVE system has an effective penetration of roughly 60 meters. Acquisition parameters and preliminary results are provided in SGW-39674, Airborne Electromagnetic Survey Report, 200-PO-1 Groundwater Operable Unit, 600 Area, Hanford Site. Airborne data are interpreted in this report in an attempt to identify areas of likely preferential groundwater flow within the aquifer system based on the presence of paleochannels or fault zones. The premise for the interpretation is that coarser-grained intervals have filled in scour channels created by episodic catastrophic flood events during the late Pleistocene. The interpretation strategy used the magnetic field anomaly data and existing bedrock maps to identify likely fault or lineament zones. Combined analysis of the magnetic, 60-Hz noise monitor, and flight-altitude (radar) data were used to identify zones where EM response is more likely due to cultural interference and or bedrock structures. Cross-sectional and map view presentations of the EM data were used to identify more electrically resistive zones that likely correlate with coarser-grained intervals. The resulting interpretation identifies one major northwest-southeast trending

  20. Search for the Pygmy Dipole Resonance in {sup 68}Ni at 600 MeV/nucleon

    SciTech Connect (OSTI)

    Wieland, O.; Benzoni, G.; Blasi, N.; Brambilla, S.; Million, B.; Bracco, A.; Camera, F.; Crespi, F. C. L.; Leoni, S.; Nicolini, R.; Maj, A.; Bednarczyk, P.; Grebosz, J.; Kmiecik, M.; Meczynski, W.; Styczen, J.; Wollersheim, H. J.; Aumann, T.; Banu, A.; Beck, T.

    2009-03-06

    The {gamma} decay from Coulomb excitation of {sup 68}Ni at 600 MeV/nucleon on a Au target was measured using the RISING setup at the fragment separator of GSI. The {sup 68}Ni beam was produced by a fragmentation reaction of {sup 86}Kr at 900 MeV/nucleon on a {sup 9}Be target and selected by the fragment separator. The {gamma} rays produced at the Au target were measured with HPGe detectors at forward angles and with BaF{sub 2} scintillators at backward angles. The measured spectra show a peak centered at approximately 11 MeV, whose intensity can be explained in terms of an enhanced strength of the dipole response function (pygmy resonance). Such pygmy structure has been predicted in this unstable neutron-rich nucleus by theory.

  1. Residual and applied stress analysis of an alloy 600 row 1 U-bend: Final report

    SciTech Connect (OSTI)

    Ruud, C.O.

    1987-09-01

    Residual stresses in Inconel alloy 600, row 1, U-bend tubes, used in heat exchanges in nuclear reactors, were studied using an advanced x-ray diffraction instrument. Both axial and circumferential (hoop) stresses on the extrados, intrados, and flanks on the O.D. surface of several U-bends were mapped. The I.D. surface residual stresses at the extrados of the U-bend were mapped on one tube and subsurface stress measurements were made on the I.D. and O.D. surfaces of that tube. Service loads were simulated on one tube to ascertain combined effect of residual and applied stresses. Data from wall thickness and profilometry measurements were also correlated with residual stress measurements. 21 refs., 42 figs.

  2. A model of caustic stress corrosion crack initiation and growth in Alloy 600. Final report

    SciTech Connect (OSTI)

    Eason, E.D.; Nelson, E.E.

    1994-06-01

    In this project, data previously generated by Westinghouse on the stress corrosion of Alloy 600 in caustic environments were analyzed to produce a model of the initiation time and crack growth rate. The model is valid over the range of the data, which included one (1), ten (10) and fifty (50) percent caustic solutions, at temperatures ranging from 550 to 650{degrees}F (288 - 343{degrees}C). The specimens were {open_quotes}C{close_quotes} ring specimens, with an initial strain that ranged from slightly below yield to approximately 3%. The model has two parts, a probabilistic model of time to initiation, and a deterministic model of crack growth rate given that initiation has occurred. Both parts of the model depend on heat treatment, caustic concentration, temperature, and strain. The model provides a reasonable representation of the material behavior over the range of data that were available for calibration.

  3. Rapid identification of conditions causing intergranular corrosion or intergranular stress corrosion cracking in sensitized alloy 600

    SciTech Connect (OSTI)

    Woodward, J.

    1984-12-01

    In 1973, Seys and van Haute introduced a technique for measuring pitting potentials. They called this technique the Static Potential Band Method. A metal wire was mounted in a corrosion cell with counter and reference electrodes, and an electrical connection made to one end. A potential was applied with a potentiostat. At the same time, a constant current was passed through the wire to create a potential gradient in the metal phase; the result was the creation of a gradient in the electrode potential along the wire. This technique has many applications in corrosion studies. In this work, it has been applied to the intergranular corrosion (IGC) and intergranular stress corrosion cracking (IGSCC) of sensitized Alloy 600 in a sulfur-containing environment.

  4. Evaluation of the 2008 Lexus LS 600H Hybrid Synergy Drive System

    SciTech Connect (OSTI)

    Burress, T.A.; Coomer, C.L.; Campbell, S.L.; Wereszczak, A.A.; Cunningham, J.P.; Marlino, L.D.; Seiber, L.E.; Lin, H.T.

    2009-01-15

    Subsystems of the 2008 Lexus 600h hybrid electric vehicle (HEV) were studied and tested as part of an intensive benchmarking effort carried out to produce detailed information concerning the current state of nondomestic alternative vehicle technologies. Feedback provided by benchmarking efforts is particularly useful to partners of the Vehicle Technologies collaborative research program as it is essential in establishing reasonable yet challenging programmatic goals which facilitate development of competitive technologies. The competitive nature set forth by the Vehicle Technologies program not only promotes energy independence and economic stability, it also advocates the advancement of alternative vehicle technologies in an overall global perspective. These technologies greatly facilitate the potential to reduce dependency on depleting natural resources and mitigate harmful impacts of transportation upon the environment.

  5. Cone beam breast CT with a high pitch (75 μm), thick (500 μm) scintillator CMOS flat panel detector: Visibility of simulated microcalcifications

    SciTech Connect (OSTI)

    Shen, Youtao; Zhong, Yuncheng; Lai, Chao-Jen; Wang, Tianpeng; Shaw, Chris C.

    2013-10-15

    Purpose: To measure and investigate the improvement of microcalcification (MC) visibility in cone beam breast CT with a high pitch (75 μm), thick (500 μm) scintillator CMOS/CsI flat panel detector (Dexela 2923, Perkin Elmer).Methods: Aluminum wires and calcium carbonate grains of various sizes were embedded in a paraffin cylinder to simulate imaging of calcifications in a breast. Phantoms were imaged with a benchtop experimental cone beam CT system at various exposure levels. In addition to the Dexela detector, a high pitch (50 μm), thin (150 μm) scintillator CMOS/CsI flat panel detector (C7921CA-09, Hamamatsu Corporation, Hamamatsu City, Japan) and a widely used low pitch (194 μm), thick (600 μm) scintillator aSi/CsI flat panel detector (PaxScan 4030CB, Varian Medical Systems) were also used in scanning for comparison. The images were independently reviewed by six readers (imaging physicists). The MC visibility was quantified as the fraction of visible MCs and measured as a function of the estimated mean glandular dose (MGD) level for various MC sizes and detectors. The modulation transfer functions (MTFs) and detective quantum efficiencies (DQEs) were also measured and compared for the three detectors used.Results: The authors have demonstrated that the use of a high pitch (75 μm) CMOS detector coupled with a thick (500 μm) CsI scintillator helped make the smaller 150–160, 160–180, and 180–200 μm MC groups more visible at MGDs up to 10.8, 9, and 10.8 mGy, respectively. It also made the larger 200–212 and 212–224 μm MC groups more visible at MGDs up to 7.2 mGy. No performance improvement was observed for 224–250 μm or larger size groups. With the higher spatial resolution of the Dexela detector based system, the apparent dimensions and shapes of MCs were more accurately rendered. The results show that with the aforementioned detector, a 73% visibility could be achieved in imaging 160–180 μm MCs as compared to 28% visibility achieved by

  6. Analysis of large scale tests for AP-600 passive containment cooling system

    SciTech Connect (OSTI)

    Sha, W.T.; Chien, T.H.; Sun, J.G.; Chao, B.T.

    1997-07-01

    One unique feature of the AP-600 is its passive containment cooling system (PCCS), which is designed to maintain containment pressure below the design limit for 72 hours without action by the reactor operator. During a design-basis accident, i.e., either a loss-of-coolant or a main steam-line break accident, steam escapes and comes in contact with the much cooler containment vessel wall. Heat is transferred to the inside surface of the steel containment wall by convection and condensation of steam and through the containment steel wall by conduction. Heat is then transferred from the outside of the containment surface by heating and evaporation of a thin liquid film that is formed by applying water at the top of the containment vessel dome. Air in the annual space is heated by both convection and injection of steam from the evaporating liquid film. The heated air and vapor rise as a result of natural circulation and exit the shield building through the outlets above the containment shell. All of the analytical models that are developed for and used in the COMMIX-ID code for predicting performance of the PCCS will be described. These models cover governing conservation equations for multicomponents single phase flow, transport equations for the {kappa}-{epsilon} two-equation turbulence model, auxiliary equations, liquid-film tracking model for both inside (condensate) and outside (evaporating liquid film) surfaces of the containment vessel wall, thermal coupling between flow domains inside and outside the containment vessel, and heat and mass transfer models. Various key parameters of the COMMIX-ID results and corresponding AP-600 PCCS experimental data are compared and the agreement is good. Significant findings from this study are summarized.

  7. Stress corrosion cracking behavior of Alloy 600 in high temperature water

    SciTech Connect (OSTI)

    Webb, G.L.; Burke, M.G.

    1995-07-01

    SCC susceptibility of Alloy 600 in deaerated water at 360 C (statically loaded U-bend specimens) is dependent on microstructure and whether the material was cold-worked and annealed (CWA) or hot-worked and annealed (HWA). All cracking was intergranular, and materials lacking grain boundary carbides were most susceptible to SCC initiation. CWA tubing materials are more susceptible to SCC initiation than HWA ring-rolled forging materials with similar microstructures (optical metallography). In CWA tubing materials, one crack dominated and grew to a visible size. HWA materials with a low hot-working finishing temperature (<925 C) and final anneals at 1010-1065 C developed both large cracks (similar to those in CWA materials) and small intergranular microcracks detectable only by destructive metallography. HWA materials with a high hot-working finishing temperature (>980 C) and a high-temperature final anneal (>1040 C), with grain boundaries that are fully decorated, developed only microcracks in all specimens. These materials did not develop large, visually detectable cracks, even after more than 300 weeks exposure. A low-temperature thermal treatment (610 C for 7h), which reduces or eliminates SCC in Alloy 600, did not eliminate microcrack formation in high temperature processed HWA materials. Conventional metallographic and analytical electron microscopy (AEM) were done on selected materials to identify the factors responsible for the observed differences in cracking behavior. Major difference between high-temperature HWA and low-temperature HWA and CWA materials was that the high temperature processing and final annealing produced predominantly ``semi-continuous`` dendritic M{sub 7}C{sub 3} carbides along grain boundaries with a minimal amount of intragranular carbides. Lower temperature processing produced intragranular M7C3 carbides, with less intergranular carbides.

  8. Stress corrosion cracking of alloys 690, 800, and 600 in acid environments containing copper oxides

    SciTech Connect (OSTI)

    Pierson, E.; Stubbe, J.; Deny, G.

    1996-10-01

    Secondary side stress corrosion cracking (SCC) of steam generator (SG) tubes may be due to the formation of an acid environment in crevices, as demonstrated for several Belgian PWR plants. The susceptibility of alloys 600 and 800 in this type of environment, which had been partially evidenced by several laboratory works, has been confirmed by capsule tests performed at Laborelec, whereas the SCC resistance of alloy 690 always appeared excellent. Capsule tests have been recently conducted at 320 C with the same heats of tubings in the same acid solutions (cationic resins + magnetite + sodium silicate, with or without lead, and sodium sulfate + iron sulfate, with or without lead oxide) containing CuO and Cu{sub 2}O. It appeared that the SCC resistance of the three alloys was generally reduced by the addition of copper oxides, at least when the cover gas did not contain hydrogen. The situation was particularly dramatic for the capsules made of alloy 690 tubing: most of them developed deep cracks, sometimes throughwall (the shortest time to failure being less than 50 h) whereas the same solutions without copper oxides had produced no cracking at all in alloy 690 capsules exposed during more than 2,000 h. Although the corrosion is reduced in presence of hydrazine or at lower concentration, copper oxides probably contribute significantly to the degradation of the tubes in alloy 600, at least in SG`s forming acid sulfate crevice environments. This is also an issue for the new SG`s, especially for those equipped with tubes in alloy 690 TT, particularly for the top of the tubesheet which is a critical deposit area since the high stresses and strains resulting from the expansion of the tube in the tubesheet lead to a risk of circumferential cracking at the transition.

  9. Gary No. 13 blast furnace achieves 400 lbs/THM coal injection in 9 months

    SciTech Connect (OSTI)

    Sherman, G.J.; Schuett, K.J.; White, D.G.; O`Donnell, E.M.

    1995-12-01

    Number 13 Blast Furnace at Gary began injecting Pulverized Coal in March 1993. The injection level was increased over the next nine months until a level off 409 lbs/THM was achieved for the month of December 1993. Several major areas were critical in achieving this high level of Pulverized coal injection (PCI) including furnace conditions, lance position, tuyere blockage, operating philosophy, and outages. The paper discusses the modifications made to achieve this level of injection. This injection level decreased charged dry coke rate from 750 lbs/THM to about 625 lbs/THM, while eliminating 150 lbs/THM of oil and 20 lbs/THM of natural gas. Assuming a 1.3 replacement ratio for an oil/natural gas mixture, overall coke replacement for the coal is about 0.87 lbs coke/lbs coal. Gary Works anticipates levels of 500 lbs/THM are conceivable.

  10. NA-ASC-500-13 Issue 26 ASC eNews Quarterly Newsletter

    National Nuclear Security Administration (NNSA)

    NA-ASC-500-13 Issue 26 ASC eNews Quarterly Newsletter December 2013 2 shutdown. But the two-year budget agreement is not an appropriation, so we must await final appropriations for both FY14 and FY15. The President also signed the National Defense Authorization Act into law, which directs NNSA to develop and carry out a plan to incorporate exascale computing in the Stockpile Stewardship Program. This is not an exascale program, but recognition that stockpile stewardship requires exascale

  11. Mr. R. B. Bell, Jr. Combustion Engineering, Inc. Post Office Box 500

    Office of Legacy Management (LM)

    g@ *tq 47 e "Y q$ . -0 t: 2 ~ i' ,; B 0 e %d&$ Department of Energy Washington, DC 20585 Mr. R. B. Bell, Jr. Combustion Engineering, Inc. Post Office Box 500 Windsor, Connecticut 06095-0500 Dear Mr. Bell: I have received two copies of the access agreement for the radiological survey of the Combustion Engineering Property at 1000 Prospect Hill Road in Windsor. I have signed the agreements on behalf of the U.S. Department of Energy, and I am returning one signed original copy to you, By

  12. Regge trajectory of the f0(500) resonance from a dispersive connection to its pole

    SciTech Connect (OSTI)

    Nebreda, J.; Londergan, J. Timothy; Pelaez, Jose R.; Szczepaniak, Adam P.

    2014-11-01

    We report here our results on how to obtain the Regge trajectory of a resonance from its pole in a scattering process by imposing analytic constraints in the complex angular momentum plane. The method, suited for resonances that dominate an elastic scattering amplitude, has been applied to the ρ (770) and the f0(500) resonances. Whereas for the former we obtain a linear Regge trajectory, characteristic of ordinary quark-antiquark states, for the latter we find a non-linear trajectory with a much smaller slope at the resonance mass. This provides a strong indication of the non-ordinary nature of the sigma meson.

  13. Process control system of a 500-MW unit of the Reftinskaya local hydroelectric power plant

    SciTech Connect (OSTI)

    L.L. Grekhov; V.A. Bilenko; N.N. Derkach; A.I. Galperina; A.P. Strukov

    2002-05-01

    The results of the installation of a process control system developed by the Interavtomatika Company (Moscow) for controlling a 500-MW pulverized coal power unit with the use of the Teleperm ME and OM650 equipment of the Siemens Company are described. The system provides a principally new level of automation and process control through monitors comparable with the operation of foreign counterparts with complete preservation of the domestic peripheral equipment. During the 4.5 years of operation of the process control system the intricate algorithms for control and data processing have proved their operational integrity.

  14. Process Control System of a 500-MW Unit of the Reftinskaya Local Hydroelectric Power Plant

    SciTech Connect (OSTI)

    Grekhov, L. L.; Bilenko, V. A.; Derkach, N. N.; Galperina, A. I.; Strukov, A. P.

    2002-05-15

    The results of the installation of a process control system developed by the Interavtomatika Company (Moscow) for controlling a 500-MW pulverized coal power unit with the use of the Teleperm ME and OM650 equipment of the Siemens Company are described. The system provides a principally new level of automation and process control through monitors comparable with the operation of foreign counterparts with complete preservation of the domestic peripheral equipment. During the 4.5 years of operation of the process control system the intricate algorithms for control and data processing have proved their operational integrity.

  15. Mechanisms of stress corrosion cracking and intergranular attack in Alloy 600 in high temperature caustic and pure water

    SciTech Connect (OSTI)

    Bandy, R.; van Rooyen, D.

    1984-01-01

    In recent years, several studies have been conducted on the intergranular stress corrosion cracking (SCC) and intergranular attack (IGA) of Alloy 600. A combination of SCC and IGA has been observed in Alloy 600 tubing on the hot leg of some operating steam generators in pressurized water reactor (PWR) nuclear power plants, and sodium hydroxide along with several other chemical species have been implicated in the tube degradations. SCC has been observed above and within the tube sheet, whereas IGA is generally localized within the tube sheet. Alloy 600 is also susceptible to SCC in pure and primary water. Various factors that influence SCC and IGA include metallurgical conditions of the alloy, concentrations of alkaline species, impurity content of the environment, temperature and stress. The mechanisms of these intergranular failures, however, are not well understood. Some of the possible mechanisms of the SCC and IGA in high temperature water and caustic are described in this paper.

  16. 70003-MAPPER FAB CARRIAGE ASSY

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    RSF RSF RSF 70003 2107 - 2107 - - - INITIAL ISSUE - - WEIGHT: 1563 LBS 146.00 CENT REF 3.00 4.00 150.00 CENT REF 6.00 SQ .50 WALL 2.00 .25 WALL 4.00 3.50 0 5.00 57.00 58.00...

  17. THE PROPERTIES OF THE 500 K DWARF UGPS J072227.51-054031.2 AND A STUDY OF THE FAR-RED FLUX OF COLD BROWN DWARFS

    SciTech Connect (OSTI)

    Leggett, S. K.; Saumon, D.; Marley, M. S.; Lodders, K.; Fegley, B.; Canty, J.; Lucas, P.; Burningham, Ben; Jones, H. R. A.; Marocco, F.; Pinfield, D. J.; Smart, R. L.; Homeier, D.; Allard, F.; Day-Jones, A.; Ishii, Miki; Tamura, M.

    2012-04-01

    We present i and z photometry for 25 T dwarfs and 1 L dwarf. Combined with published photometry, the data show that the i - z, z - Y, and z - J colors of T dwarfs are very red, and continue to increase through to the late-type T dwarfs, with a hint of a saturation for the latest types with T{sub eff} Almost-Equal-To 600 K. We present new 0.7-1.0 {mu}m and 2.8-4.2 {mu}m spectra for the very late type T dwarf UGPS J072227.51-054031.2, as well as improved astrometry for this dwarf. Examination of the spectral energy distribution using new and published data, with Saumon and Marley models, shows that the dwarf has T{sub eff} = 505 {+-} 10 K, a mass of 3-11 M{sub Jupiter}, and an age between 60 Myr and 1 Gyr. This young age is consistent with the thin disk kinematics of the dwarf. The mass range overlaps with that usually considered to be planetary, despite this being an unbound object discovered in the field near the Sun. This apparently young rapid rotator is also undergoing vigorous atmospheric mixing, as determined by the IRAC and WISE 4.5 {mu}m photometry and the Saumon and Marley models. The optical spectrum for this 500 K object shows clearly detected lines of the neutral alkalis Cs and Rb, which are emitted from deep atmospheric layers with temperatures of 900-1200 K.

  18. Conceptual Design of 500 watt portable thermophotovoltaic power supply using JP-8 fuel

    SciTech Connect (OSTI)

    DeBellis, C.L.; Scotto, M.V.; Fraas, L.

    1997-03-01

    Babcock & Wilcox (B&W) and JX Crystals (JXC) have developed an innovative design for a compact, 500 watt net electric (We), 24-VDC thermophotovoltaic (TPV) power supply using JP-8 fuel. As currently envisioned, the TPV generator will be approximately 20 cm (8 inches) in diameter and 50 cm (20 inches) high, not including a fuel tank and controls. The total system may weigh as little as 7.5 kg (16.5 lb) without fuel. This system will achieve high efficiency and high power density relative to its size through the use of low bandgap gallium antimonide (GaSb) PV cells and a matched emitter. A thermally integrated fuel vaporizer and recuperator will boost system efficiency by transferring the unused energy in the exhaust stream to the incoming fuel and combustion air. At rated conditions and 500 We output, the system is expected to have an overall efficiency of 8{percent} to 10{percent}. This paper examines the trade-offs between system efficiency, power density, and weight required in the selection and configuration of the major system components. {copyright} {ital 1997 American Institute of Physics.}

  19. Texture, residual strain, and plastic deformation around scratches in alloy 600 using synchrotron x-ray Laue micro-diffraction.

    SciTech Connect (OSTI)

    Suominen Fuller, M. L.; Klassen, R. J.; McIntyre, N. S.; Gerson, A. R.; Ramamurthy, S.; King, P. J.; Liu, W.; Univ. of Western Ontario; Univ. of South Australia; Babcock & Wilcox Canada

    2008-01-01

    Deformation around two scratches in Alloy 600 (A600) was studied nondestructively using synchrotron Laue differential aperture X-ray microscopy. The orientation of grains and elastic strain distribution around the scratches were measured. A complex residual deviatoric elastic strain state was found to exist around the scratches. Heavy plastic deformation was observed up to a distance of 20 {micro}m from the scratches. In the region 20-30 {micro}m from the scratches the diffraction spots were heavily streaked and split indicating misoriented dislocation cell structures.

  20. Effects of carbides on susceptibility of alloy 600 to stress corrosion cracking in high-temperature water

    SciTech Connect (OSTI)

    Rebak, R.B.; Xia, Z.; Szklarska-Smialowska, Z. . Fontana Corrosion Center)

    1993-11-01

    The electrochemical behavior of sensitized, carburized, and mill-annealed alloy 600 (UNS N06600) was studied in hydrogenated, aerated, and high-temperature (250 to 350 C) dilute aqueous solutions. In high-temperature water at high anodic potentials, the current density (DC) from carbide dissolution was higher than DC from matrix dissolution. In oxidizing environments, intergranular stress corrosion cracking propagated in alloy 600 by dissolution of continuous or semicontinuous carbides at the grain boundary, in sensitized and non-sensitized materials. These studies have been conducted in environments similar to those in the steam generators of pressurized water reactors (PWR) in nuclear power plants.

  1. PDSF Office Hours 10/17/13 from 2:00 to 4:00 pm at LBNL

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    0/17/13 from 2:00 to 4:00 pm at LBNL PDSF Office Hours 10/17/13 from 2:00 to 4:00 pm at LBNL October 7, 2013 I have biweekly office hours on Thursdays at LBNL. The next one is Thursday 10/17/13 from 2:00 - 4:00 pm in the NERSC drop in office at 050A-0143A (in the basement by the bus offices). Please feel free to stop by if you have any questions or want some hands on help with PDSF issues. Subscribe via RSS Subscribe Browse by Date February 2014 January 2014 November 2013 October 2013 September

  2. Neutron-Induced Microstructural Evolution of Fe-15Cr-16Ni Alloys at ~400 C During Neutron Irradiation in the FFTF Fast Reactor

    SciTech Connect (OSTI)

    Okita, Taira; Sato, Toshihiko; Sekimura, Naoto; Garner, Francis A.; Greenwood, Lawrence R.; Wolfer, W. G.; Isobe, Yoshihiro

    2001-06-30

    An experiment conducted at ~400 degrees C on simple model austenitic alloys (Fe-15Cr-16Ni and Fe-15Cr-16Ni-0.25Ti, both with and without 500 appm boron) irradiated in the FFTF fast reactor at seven different dpa rates clearly shows that lowering of the atomic displacement rate leads to a pronounced reduction in the transient regime of void swelling. While the steady state swelling rate (~1%/dpa) of these alloys is unaffected by changes in the dpa rate, the transient regime of swelling can vary from <1 to ~60 dpa when the dpa rate varies over more than two orders of magnitude. This range of dpa rates covers the full span of fusion, PWR and fast reactor rates. The origin of the flux sensitivity of swelling arises first in the evolution of the Frank dislocation loop population, its unfaulting, and the subsequent evolution of the dislocation network. There also appears to be some flux sensitivity to the void nucleation process. Most interestingly, the addition of titanium suppresses the void nucleation process somewhat, but does not alter the duration of the transient regime of swelling or its sensitivity to dpa rate. Side-by-side irradiation of boron-modified model alloys in this same experiment shows that higher helium generation rates homogenize the swelling somewhat, but do not significantly change its magnitude or flux sensitivity. The results of this study support the prediction that austenitic alloys irradiated at PWR-relevant displacement rates will most likely swell more than when irradiated at higher rates characteristic of fast reactors. Thus, the use of swelling data accumulated in fast reactors may possibly lead to an under-prediction of swelling in lower-flux PWRs and fusion devices.

  3. Monte Carlo evaluation of CTDI{sub {infinity}} in infinitely long cylinders of water, polyethylene and PMMA with diameters from 10 mm to 500 mm

    SciTech Connect (OSTI)

    Zhou Hong; Boone, John M.

    2008-06-15

    Monte Carlo simulations were used to evaluate the radiation dose to infinitely long cylinders of water, polyethylene, and poly(methylmethacrylate) (PMMA) from 10 to 500 mm in diameter. Radiation doses were computed by simulating a 10 mm divergent primary beam striking the cylinder at z=0, and the scattered radiation in the -z and +z directions was integrated out to infinity. Doses were assessed using the total energy deposited divided by the mass of the 10-mm-thick volume of material in the primary beam. This approach is consistent with the notion of the computed tomography dose index (CTDI) integrated over infinite z, which is equivalent to the dose near the center of an infinitely long CT scan. Monoenergetic x-ray beams were studied from 5 to 140 keV, allowing polyenergetic x-ray spectra to be evaluated using a weighted average. The radiation dose for a 10-mm-thick CT slice was assessed at the center, edge, and over the entire diameter of the phantom. The geometry of a commercial CT scanner was simulated, and the computed results were in good agreement with measured doses. The absorbed dose in water for 120 kVp x-ray spectrum with no bow tie filter for a 50 mm cylinder diameter was about 1.2 mGy per mGy air kerma at isocenter for both the peripheral and center regions, and dropped to 0.84 mGy/mGy for a 500-mm-diam water phantom at the periphery, where the corresponding value for the center location was 0.19 mGy/mGy. The influence of phantom composition was studied. For a diameter of 100 mm, the dose coefficients were 1.23 for water, 1.02 for PMMA, and 0.94 for polyethylene (at 120 kVp). For larger diameter phantoms, the order changed--for a 400 mm phantom, the dose coefficient of polyethylene (0.25) was greater than water (0.21) and PMMA (0.16). The influence of the head and body bow tie filters was also studied. For the peripheral location, the dose coefficients when no bow tie filter was used were high (e.g., for a water phantom at 120 kVp at a diameter of 300

  4. How to program 122,400 heterogeneous cores and retain your sanity

    SciTech Connect (OSTI)

    Patkin, Scott

    2010-01-01

    Current technology trends favor hybrid architectures, typically with each node in a cluster containing both general-purpose and specialized 'accelerator' processors. The typical model for programming such systems is host-centric: The general-purpose processor orchestrates the computation, offloading performance-critical work to the accelerator, and data is communicated only among general-purpose processors. In this talk we propose a radically different hybrid-programming approach, which we call the 'reverse-acceleration model'. In this model the accelerators orchestrate the computation, offloading unacceleratable work to the general-purpose processors. Data is communicated among accelerators, not among general-purpose processors. We present the Cell Messaging Layer (CML), an implementation of the reverse-acceleration model for Los Alamos National Laboratory's Roadrunner supercomputer, a complex conglomerate of 122,400 processor cores of various types, multiple memory domains, and multiple network types, all with radically different performance characteristics but which together make Roadrunner the world's second-fastest supercomputer. CML demonstrates a new messaging-layer implementation technique called 'receiver-initiated message passing', which reduces communication latency by up to a third. Our thesis is that the reverse-acceleration model simplifies porting codes to heterogeneous systems and facilitates performance optimization. We present a case study of a legacy neutron-transport code that we modified to use reverse acceleration. Performance results from running this code across the full Roadrunner system indicate a substantial performance improvement over the unaccelerated version of the code.

  5. Stress corrosion cracking of Ni-Cu alloy 400 tubes in feedwater heaters

    SciTech Connect (OSTI)

    Amar, A.S.

    1994-12-31

    This paper presents the results of the inspections and metallurgical evaluations of a high pressure feedwater heater that experienced numerous tube failures after a short service life. Using EPRI NDE Center technical support, tubes were eddy current tested with special probes in the tubesheet region and with conventional probes in the remaining straight portion. Pulled tubes were metallurgically examined. Crack depths were correlated with eddy current indications. Short axial cracks were found on the inner surface of the tubes at roll transitions. Failures were attributed to intergranular stress corrosion cracking. The cold drawn-stress relieved Monel{trademark} (Alloy 400) tube had < 10 KSI hoop residual stress, however the residual stress was probably much higher in the roll transition. A large number of tubes were plugged based on the eddy current indications, however several tubes that showed no indications had leaked a few months later. This suggested that after initiation, crack growth was rapid. The heater was replaced after 4.5 years of service.

  6. Influence of grain size on the constitutive response and substructure evolution of MONEL 400

    SciTech Connect (OSTI)

    Gray, G.T. III, Chen, S.R.; Vecchio, K.S.

    1999-05-01

    The influence of grain size on the constitutive behavior (strain-rate and temperature dependence of the yield stress and strain hardening) and substructure evolution of MONEL 400 was investigated. Increasing the grain size from 9.5 to 202 {micro}m was seen to reduce the quasi-static yield strength from 290 to 115 MPa, while having a minimal effect on the work-hardening response. Increasing the strain rate from quasi-static to dynamic strain rates (3000 s{sup {minus}1}) was seen to increase the yield and overall flow-stress levels, but has no effect on the strong grain-size dependency exhibited of this alloy. The persistent influence of grain size to large strains is inconsistent with previous d{sup {minus}1/2} pileup grain-size modeling in the literature, which predicts convergence at large strains. Substructure evolution differences between the grain interiors and adjacent to grain boundaries supports differential defect storage processes which are consistent with previously published work-hardening d{sup {minus}1} modeling arguments for grain size-dependent strengthening in polycrystals. The integration of grain-size dependency into constitutive modeling using the mechanical threshold stress (MTS) model is discussed. The MTS model is shown to provide a robust constitutive description capturing yielding, large-strain work hardening, and grain-size effects simultaneously. The MTS model is, additionally, shown to satisfactorily address the experimentally observed transients due to strain-rate or temperature-path dependency.

  7. Planning for the 400,000 tons/year AISI ironmaking demonstration plant

    SciTech Connect (OSTI)

    Aukrust, E. . AISI Direct Steelmaking Program)

    1993-01-01

    The American Iron and Steel Institute (AISI) has formulated a four-year program to design, construct, and operate a 400,000 net ton per year ironmaking demonstration plant. The plant will employ the coal-based ironmaking process developed under a 1989 cooperative agreement with DOE. AISI will manage the design and construction to be completed in the first two years and operate the plant for the second two years with a variety or ores, coals, and fluxes. Campaigns of increasing length are planned to optimize operations. After successful operation, the plant will be taken over by the host company. Results of studies to date indicate that, on a commercial scale, the AISI process will use 27% less energy and have variable operating costs $10 per ton lower and capital costs of $160 per annual ton, compared to the $250 per annual ton rebuild cost for the coke oven-blast furnace process it will replace. The process will enable the domestic steel industry to become more competitive by reducing its capital and operating cost. Furthermore, by eliminating the pollution problems associated with coke production and by completely enclosing the smelting reactions, this process represents a major step towards an environmentally friendly steel industry.

  8. Gadolinium-148 production cross section measurements for 600-and 800-MEV protons.

    SciTech Connect (OSTI)

    Kelley, K. C.; Devlin, M. J.; Pitcher, E. J.; Mashnik, S. G.; Hertel, N. E.

    2004-01-01

    In a series of experiments at LANSCE's WNR facility, {sup 148}Gd production was measured for 600- and 800-MeV protons on tungsten, tantalum, and gold. These experiments used 3 {mu}m thin W, Ta, and Au foils and 10 {mu}m thin Al activation foils. Gadolinium spallation yields were determined from these foils using alpha spectroscopy and compared with the LANL codes CEM2k+GEM2 and MCNPX. When heavy metal targets, such as tungsten, are bombarded with protons greater than a few hundred MeV many different nuclides are produced. These nuclides are both stable and radioactive and are created by spallation, proton activation, or secondary reactions with neutrons and other nuclear particles made in the target. These products are distributed somewhat heterogeneously throughout a thick target because of the energy dependence of the cross sections and energy loss of the proton beam within the target. From this standpoint, it is difficult to measure nuclide production cross sections for a given energy proton in a thick target. At the Los Alamos Neutron Science Center (LANSCE) accelerator complex, protons are accelerated to 800 MeV and directed to two tungsten targets, Target 4 at the Weapons Neutron Research (WNR) facility and 1L target at the Manuel Lujan Jr. Neutron Scattering Center. DOE requires hazard classification analyses to be performed on these targets and places limits on radionuclide inventories in the target as a means of determining the 'nuclear facility' category level. Presently, WNR's Target 4 is a non-nuclear facility while the Lujan 1L target is classified as a Category 3 nuclear facility. Gadolinium-148 is a radionuclide created from the spallation of tungsten and other heavy elements. Allowable isotopic inventories are particularly low for this isotope because it is an alpha-particle emitter with a 75-year half-life. The activity level of {sup 148}Gd is generally low, but it encompasses almost two-thirds of the total inhalation dose burden in an accident

  9. Effect of cold work and processing orientation on stress corrosion cracking behavior of alloy 600

    SciTech Connect (OSTI)

    Moshier, W.C.; Brown, C.M.

    2000-03-01

    Cold work accelerates stress corrosion cracking (SCC) growth rates in Alloy 600 (UNS N06600). However, the variation in crack growth rates generated from cold-worked material has been significant, and the effect has been difficult to quantify. A study was performed in hydrogenated water adjusted to pH 10.2 to evaluate systematically the effect of cold work on Alloy 600 as a function of temperature, amount of cold work, stress intensity factor, and processing orientation. Cold work was introduced into the material by tensile prestraining or cold-rolling plate product. Crack growth rates were determined between 252 C and 360 C, stress intensity factors between 21 MPa{radical}m and 55 MPa{radical}m, and yield strengths between 201 MPa and 827 MPa. The material with the highest yield strength was cold-rolled and tested in the longitudinal-transverse (LT) and short-transverse (ST) orientations. Crack growth rates increased with increasing temperature, stress intensity factor, and yield strength. Furthermore, crack growth rates were a strong function of the processing orientation in the cold-rolled plate, with growth rates approximately an order of magnitude greater in the ST orientation compared to the LT orientation. Crack growth rates in the LT orientation were measured between 0.003 x 10{sup {minus}9} m/s and 1.95 x 10{sup {minus}9} m/s and between 0.066 x 10{sup {minus}9} m/s and 6.3 x 10{sup {minus}9} m/s in the ST orientation. Activation energies were slightly greater in the ST orientation, ranging from 154 kcal/mol to 191 kcal/mol, compared to activation energies between 126 kJ/mol and 157 kJ/mol in the LT orientation. Results of this study demonstrated that, although cold work can be used to accelerate SCC, the orientation of crack growth significantly can affect the results and must be taken into account when analyzing data from cold-worked material.

  10. Three-dimensional analysis of AP600 standard plant shield building roof

    SciTech Connect (OSTI)

    Greimann, L.; Fanous, F.; Safar, S.; Khalil, A.; Bluhm, D.

    1999-06-01

    The AP600 passive containment vessel is surrounded by a concrete cylindrical shell covered with a truncated conical roof. This roof supports the passive containment cooling system (PCS) annular tank, shield plate and other nonstructural attachments. When the shield building is subjected to different loading combinations as defined in the Standard Review Plan (SRP), some of the sections in the shield building could experience forces in excess of their design values. This report summarized the three-dimensional finite element analysis that was conducted to review the adequacy of the proposed Westinghouse shield building design. The ANSYS finite element software was utilized to analyze the Shield Building Roof (SBR) under dead, snow, wind, thermal and seismic loadings. A three-dimensional model that included a portion of the shield building cylindrical shell, the conical roof and its attachments, the eccentricities at the cone-cylinder connection and at the compression ring and the PCS tank was developed. Mesh sensitivity studies were conducted to select appropriate element size in the cylinder, cone, near air intakes and in the vicinity of the eccentricities. Also, a study was carried out to correctly idealize the water-structure interaction in the PCS tank. Response spectrum analysis was used to calculate the internal forces at different sections in the SBR under Safe Shutdown Earthquake (SSE). Forty-nine structural modes and twenty sloshing modes were used. Two horizontal components of the SSE together with a vertical component were used. Modal stress resultants were combined taking into account the effects of closely spaced modes. The three earthquake directions were combined by the Square Root of the Sum Squares method. Two load combinations were studied. The load combination that included dead, snow, fluid, thermal and seismic loads was selected to be the most critical. Interaction diagrams for critical sections were developed and used to check the design

  11. Grand Coulee - Bell 500-kV Transmission Line Project, Draft Environmental Impact Statement

    SciTech Connect (OSTI)

    N /A

    2002-08-09

    BPA is proposing to construct a 500-kilovolt (kV) transmission line that would extend approximately 84 miles between the Grand Coulee 500-kV Switchyard, near Grand Coulee Dam, and the Bell Substation, in Mead just north of Spokane. The new line would cross portions of Douglas, Grant, Lincoln, and Spokane counties. In addition to the transmission line, new equipment would be installed at the substations at each end of the new line and at other facilities. The proposed action would remove an existing 115-kV transmission line and replace it with the new 500-kV line on existing right-of-way for most of its length. Additional right-of-way would be needed in the first 3.5 miles out of the Grand Coulee Switchyard to connect to the existing 115-kV right-of-way. Since the mid-1990s, the transmission path west of Spokane, called the West of Hatwai transmission pathway, has grown increasingly constrained. To date, BPA has been able to manage operation of the path through available operating practices, and customer needed have been met while maintaining the reliability of the path. however, in early 2001, operations showed that the amount of electricity that needs to flow from east to west along this path creates severe transmission congestion. Under these conditions, the system is at risk of overloads and violation of industry safety and reliability standards. The problem is particularly acute in the spring and summer months because of the large amount of power generated by dams east of the path. Large amounts of water cannot be spilled during that time in order for BPA to fulfill its obligation to protect threatened and endangered fish. The amount of power that needs to move through this area during these months at times could exceed the carrying capacity of the existing transmission lines. In additional capacity is not added, BPA will run a significant risk that it will not be able to continue to meet its contractual obligations to deliver power and maintain reliability

  12. Condensation in the presence of noncondensible gases: AP600 containment simulation

    SciTech Connect (OSTI)

    Anderson, M.H.; Corradini, M.L.

    1995-09-01

    The Westinghouse Electric Corporation has designed an advanced pressurized light water reactor, AP600. This reactor is designed with a passive cooling system to remove sensible and decay heat from the containment. The heat removal path involves condensation heat transfer, aided by natural convective forces generated by buoyancy effects. A one-twelfth scale rectangular slice of the proposed reactor containment was constructed at the University of Wisconsin to simulate conditions anticipated from transients and accidents that may occur in a full scale containment vessel under a variety of conditions. Similitude of the test facility was obtained by considering the appropriate dimensionless group for the natural convective process (modified Froude number) and the aspect ratio (H/R) of the containment vessel. An experimental investigation to determine the heat transfer coefficients associated with condensation on a vertical and horizontal cooled wall (located in the scaled test section) at several different inlet steam flow rates and test section temperatures was conducted. In this series of experiments, the non-condensible mass fraction varied between (0.9-0.4) with corresponding mixture temperatures between 60-90{degrees}C. The heat transfer coefficients of the top horizontal surface varied from (82-296)W/m{sup 2}K and the vertical side heat transfer coefficients varied form (70-269)m{sup 2}K. The results were then compared to boundary layer heat and mass transfer theory by the use of the McAdams correlation for free convection.

  13. Optical emission from a small scale model electric arc furnace in 250-600 nm region

    SciTech Connect (OSTI)

    Maekinen, A.; Tikkala, H.; Aksela, H.; Niskanen, J.

    2013-04-15

    Optical emission spectroscopy has been for long proposed for monitoring and studying industrial steel making processes. Whereas the radiative decay of thermal excitations is always taking place in high temperatures needed in steel production, one of the most promising environment for such studies are electric arc furnaces, creating plasma in excited electronic states that relax with intense characteristic emission in the optical regime. Unfortunately, large industrial scale electric arc furnaces also present a challenging environment for optical emission studies and application of the method is not straightforward. To study the usability of optical emission spectroscopy in real electric arc furnaces, we have developed a laboratory scale DC electric arc furnace presented in this paper. With the setup, optical emission spectra of Fe, Cr, Cr{sub 2}O{sub 3}, Ni, SiO{sub 2}, Al{sub 2}O{sub 3}, CaO, and MgO were recorded in the wavelength range 250-600 nm and the results were analyzed with the help of reference data. The work demonstrates that using characteristic optical emission, obtaining in situ chemical information from oscillating plasma of electric arc furnaces is indeed possible. In spite of complications, the method could possibly be applied to industrial scale steel making process in order to improve its efficiency.

  14. Primary water stress corrosion cracking of Alloy 600: Effects of processing parameters

    SciTech Connect (OSTI)

    Seman, D.J.; Webb, G.L.; Parrington, R.J.

    1993-10-22

    Correlations of stress corrosion cracking (SCC) data in deaerated water with temperature, stress, metallography, and processing for laboratory test specimens are presented. Initiation time data show that a low temperature anneal and resulting absence of grain boundary carbides result in a material having increased susceptibility to SCC. Data also show that hot worked and annealed Alloy 600 is more resistant than cold worked and annealed material, both having carbide decorated grain boundaries. In absence of grain boundary carbides, both materials are equally susceptible. Low temperature thermal treatment (1100F) reduces SCC susceptibility with or without grain boundary decoration. Weld metal data and data correlations developed from 700 double U-bends are presented. Data demonstrate the effect of increased carbon content to improve SCC resistance. The data shows that the general relation of time, temperature and strain for wrought material is followed for the weld metal. The weld process used did not affect the SCC susceptibility of EN-82 which showed a greater resistance to SCC than EN-62. Stress relief of weld deposits showed an improvement for wrought material. Heat affected zone resistance was improved if the starting material received a high temperature anneal (1850 to 2000F). Range of SCC initiation times for weld metal is comparable to the range of initiation times for wrought material.

  15. Modeling of stress distributions on the microstructural level in Alloy 600

    SciTech Connect (OSTI)

    Kozaczek, K.J.; Petrovic, B.G.; Ruud, C.O.; Mcllree, A.R.

    1995-04-01

    Stress distribution in a random polycrystalline material (Alloy 600) was studied using a topologically correct microstructural model. Distributions of von Mises and hydrostatic stresses at the grain vertices, which could be important in intergranular stress corrosion cracking, were analyzed as functions of microstructure, grain orientations and loading conditions. Grain size, shape, and orientation had a more pronounced effect on stress distribution than loading conditions. At grain vertices the stress concentration factor was higher for hydrostatic stress (1.7) than for von Mises stress (1.5). The stress/strain distribution in the volume (grain interiors) is a normal distribution and does not depend on the location of the studied material volume i.e., surface vs/bulk. The analysis of stress distribution in the volume showed the von Mises stress concentration of 1.75 and stress concentration of 2.2 for the hydrostatic pressure. The observed stress concentration is high enough to cause localized plastic microdeformation, even when the polycrystalline aggregate is in the macroscopic elastic regime. Modeling of stresses and strains in polycrystalline materials can identify the microstructures (grain size distributions, texture) intrinsically susceptible to stress/strain concentrations and justify the correctness of applied stress state during the stress corrosion cracking tests. Also, it supplies the information necessary to formulate the local failure criteria and interpret of nondestructive stress measurements.

  16. Materials corrosion of high temperature alloys immersed in 600C binary nitrate salt.

    SciTech Connect (OSTI)

    Kruizenga, Alan Michael; Gill, David Dennis; LaFord, Marianne Elizabeth

    2013-03-01

    Thirteen high temperature alloys were immersion tested in a 60/40 binary nitrate salt. Samples were interval tested up to 3000 hours at 600%C2%B0C with air as the ullage gas. Chemical analysis of the molten salt indicated lower nitrite concentrations present in the salt, as predicted by the equilibrium equation. Corrosion rates were generally low for all alloys. Corrosion products were identified using x-ray diffraction and electron microprobe analysis. Fe-Cr based alloys tended to form mixtures of sodium and iron oxides, while Fe-Ni/Cr alloys had similar corrosion products plus oxides of nickel and chromium. Nickel based alloys primarily formed NiO, with chromium oxides near the oxide/base alloy interface. In625 exhibited similar corrosion performance in relation to previous tests, lending confidence in comparisons between past and present experiments. HA230 exhibited internal oxidation that consisted of a nickel/chromium oxide. Alloys with significant aluminum alloying tended to exhibit superior performance, due formation of a thin alumina layer. Soluble corrosion products of chromium, molybdenum, and tungsten were also formed and are thought to be a significant factor in alloy performance.

  17. EIS-0514: Colusa-Sutter 500-kilovolt Transmission Line Project; Colusa and Sutter Counties, California

    Office of Energy Efficiency and Renewable Energy (EERE)

    Western Area Power Administration (Western) and the Sacramento Municipal Utility District (SMUD) are preparing a joint EIS/environmental impact report (EIR) –under, respectively, NEPA and the California Environmental Quality Act – that analyzes the potential environmental effects of the proposed new 500-kilovolt Colusa-Sutter (CoSu) Transmission Line Project. The proposed transmission line would interconnect the California-Oregon Transmission Project transmission system, near either Arbuckle or Maxwell, California, to the Central Valley Project transmission system near Yuba City, California. Western’s proposed action is to construct the CoSu Project and modify Western’s facilities to accommodate the new line; SMUD’s proposed action is to fund the proposal.

  18. Coiled tubing velocity string set at record 20,500 ft

    SciTech Connect (OSTI)

    Adams, L.S. )

    1992-04-13

    This paper reports that coiled tubing, set at record depth, significantly reduced costs and posed lower mechanical failure risk for recompleting a gas well in the Delaware basin of West Texas. Alternative completions such as replacing the existing tubing string with smaller diameter conventional API production tubing was deemed less economical and effective. The gas well, George M. Shelton No. 2, was recompleted on July 18, 1991, by Chevron U.S.A. Production Co. The gas is produced from the deep, low-pressure Ellenburger formation in the Gomez field. The hang-off depth of 20,500 ft set a world record for the deepest permanently installed coiled tubing. The 1-1/2 in. coiled tubing velocity string, run within the existing 4-1/2 and 4-in. tapered production tubing string, consists of seven segments that vary in wall thickness from 0.087 to 0.156 in.

  19. Niobium Thin Film Coating on a 500-MHz Copper Cavity by Plasma Deposition

    SciTech Connect (OSTI)

    Haipeng Wang; Genfa Wu; H. Phillips; Robert Rimmer; Anne-Marie Valente; Andy Wu

    2005-05-16

    A system using an Electron Cyclotron Resonance (ECR) plasma source for the deposition of a thin niobium film inside a copper cavity for superconducting accelerator applications has been designed and is being constructed. The system uses a 500-MHz copper cavity as both substrate and vacuum chamber. The ECR plasma will be created to produce direct niobium ion deposition. The central cylindrical grid is DC biased to control the deposition energy. This paper describes the design of several subcomponents including the vacuum chamber, RF supply, biasing grid and magnet coils. Operational parameters are compared between an operating sample deposition system and this system. Engineering work progress toward the first plasma creation will be reported here.

  20. SULFUR IX TO XIII SPECTRAL MEASURMENTS BETWEEN 170 AND 500 A

    SciTech Connect (OSTI)

    Yang, Z. H.; Zhang, B. L.; Wang, W.; Yu, D.Y.; Cai, X. H.; Du, S. B.; Zeng, X. T.; Chang, H. W.

    2009-04-15

    This paper reports laboratory measurements of the spectrum of highly ionized sulfur. The spectrum of S IX-S XIII has been observed in the wavelength range 170-500 A. A total of 54 lines have been measured. Forty-two of them have been classified as 2s {sup 2}2p{sup k} -2s2p{sup k} {sup +1} and 2s2p{sup k} -2p{sup k} {sup +1} transitions. Twelve other lines have been ascribed to 2s-2p, 4p-5s, 5p-6s, 5d-6p, and 6p-8d transitions. These spectral lines have been identified, among which 22 are new and accurately measured. The analysis of the spectra was based on a comparison with other experimental results and calculated values.

  1. New 500-kV Ion Source Test Strand for HIF

    SciTech Connect (OSTI)

    Sangster, T.C.; Ahle, L.E.; Halaxa, E.F.; Karpenko, V.P.; Oldaker, M.E.; Mitchell, J.W.; Beck, D.N.; Bieniosek, F.M.; Henestroza, E.; Kwan, J.W.

    2000-03-09

    One of the most challenging aspects of ion beam driven inertial fusion energy is the reliable and efficient generation of low emittance, high current ion beams. The primary ion source requirements include a rise time of order 1-{micro}sec, a pulse width of at least 20-{micro}sec, a flattop ripple of less than 0.1% and a repetition rate of at least 5-HZ. Naturally, at such a repetition rate, the duty cycle of the source must be greater than 10{sup 8} pulses. Although these specifications do not appear to exceed the state-of-the-art for pulsed power, considerable effort remains to develop a suitable high current ion source. Therefore, we are constructing a 500-kV test stand specifically for studying various ion source concepts including surface, plasma and metal vapor arc. This paper will describe the test stand design specifications as well as the details of the various subsystems and components.

  2. A New 500-kV Ion Source Test Stand for HIF

    SciTech Connect (OSTI)

    Sangster, T.C.; Ahle, L.E.; Halaxa, E.F.; Karpenko, V.P.; Oldaker, M. E.; Mitchell, J.W.; Beck, D.N.; Bieniosek, F.M.; Henestroza, E.; Kwan, J.W.

    2000-10-05

    One of the most challenging aspects of ion beam driven inertial fusion energy is the reliable and efficient generation of low emittance, high current ion beams. The primary ion source requirements include a rise time of order 1-msec, a pulse width of at least 20-msec, a flattop ripple of less than 0.1% and a repetition rate of at least 5-Hz. Naturally, at such a repetition rate, the duty cycle of the source must be greater than 108 pulses. Although these specifications do not appear to exceed the state-of-the-art for pulsed power, considerable effort remains to develop a suitable high current ion source. Therefore, we are constructing a 500-kV test stand specifically for studying various ion source concepts including surface, plasma and metal vapor arc. This paper will describe the test stand design specifications as well as the details of the various subsystems and components.

  3. Quantitative NO{sub 2} molecular tagging velocimetry at 500 kHz frame rate

    SciTech Connect (OSTI)

    Jiang, Naibo; Nishihara, Munetake; Lempert, Walter R.

    2010-11-29

    NO{sub 2} molecular tagging velocimetry (MTV) is demonstrated at repetition rates as high as 500 kHz in a laboratory scale Mach 5 wind tunnel. A pulse burst laser and a home built optical parametric oscillator system were used to simultaneously generate the required 355 and 226 nm wavelengths for NO{sub 2} photodissociation (tagging) and NO planar laser induced fluorescence imaging (interrogation), respectively. NO{sub 2} MTV images were obtained both in front and behind the characteristic bow shock from a 5 mm diameter cylinder. From Gaussian curve fitting, an average free stream flow velocity of 719 m/s was obtained. Absolute statistical precision in velocity of {approx}11.5 m/s was determined, corresponding to relative precision of 1.6%-5%, depending upon the region of the flow probed.

  4. Niobium thin film coating on a 500-MHz copper cavity by plasma deposition

    SciTech Connect (OSTI)

    Haipeng Wang; Genfa Wu; H. Phillips; Robert Rimmer; Anne-Marie Valente; Andy Wu

    2005-05-16

    A system using an Electron Cyclotron Resonance (ECR) plasma source for the deposition of a thin niobium film inside a copper cavity for superconducting accelerator applications has been designed and is being constructed. The system uses a 500-MHz copper cavity as both substrate and vacuum chamber. The ECR plasma will be created to produce direct niobium ion deposition. The central cylindrical grid is DC biased to control the deposition energy. This paper describes the design of several subcomponents including the vacuum chamber, RF supply, biasing grid and magnet coils. Operational parameters are compared between an operating sample deposition system and this system. Engineering work progress toward the first plasma creation will be reported here.

  5. Wavelength and Intensity Dependence of Short Pulse Laser Xenon Double Ionization between 500 and 2300 nm

    SciTech Connect (OSTI)

    Gingras, G.; Tripathi, A.; Witzel, B.

    2009-10-23

    The wavelength and intensity dependence of xenon ionization with 50 fs laser pulses has been studied using time-of-flight mass spectrometry. We compare the ion yield distribution of singly and doubly charged xenon with the Perelomov-Popov-Terent'ev (PPT) theory, Perelomov, Popov, and Terent'ev, Zh. Eksp. Teor. Fiz. 50, 1393 (1966) [Sov. Phys. JETP 23, 924 (1966)], in the regime between 500 and 2300 nm. The intensity dependence for each wavelength is measured in a range between 1x10{sup 13} and 1x10{sup 15} W/cm{sup 2}. The Xe{sup +}-ion signal is in good agreement with the PPT theory at all used wavelengths. In addition we demonstrate that ionic 5s5p{sup 6} {sup 2}S state is excited by an electron impact excitation process and contributes to the nonsequential double ionization process.

  6. Evaluations of University of Wisconsin Silicon Carbide Temperature Monitors 300 LO and 400 LO B

    SciTech Connect (OSTI)

    K. L. Davis; J. L. Rempe; D. L. Knudson; B. M. Chase; T. C. Unruh

    2011-12-01

    Silicon carbide (SiC) temperature monitors 05R4-02-A KG1403 (300 LO) and 05R4-01-A KG1415 (400 LO B) were evaluated at the High Temperature Test Lab (HTTL) to determine their peak irradiation temperatures. HTTL measurements indicate that the peak irradiation temperature for the 300 LO monitor was 295 {+-} 20 C and the peak irradiation temperature for the 400 LO B monitor was 294 {+-} 25 C. Two silicon carbide (SiC) temperature monitors irradiated in the Advanced Test Reactor (ATR) were evaluated at the High Temperature Test Lab (HTTL) to determine their peak temperature during irradiation. These monitors were irradiated as part of the University of Wisconsin Pilot Project with a target dose of 3 dpa. Temperature monitors were fabricated from high density (3.203 g/cm3) SiC manufactured by Rohm Haas with a nominal size of 12.5 mm x 1.0 mm x 0.75 mm (see Attachment A). Table 1 provides identification for each monitor with an expected peak irradiation temperature range based on preliminary thermal analysis (see Attachment B). Post irradiation calculations are planned to reduce uncertainties in these calculated temperatures. Since the early 1960s, SiC has been used as a post-irradiation temperature monitor. As noted in Reference 2, several researchers have observed that neutron irradiation induced lattice expansion of SiC annealed out when the post-irradiation annealing temperature exceeds the peak irradiation temperature. As noted in Reference 3, INL uses resistivity measurements to infer peak irradiation temperature from SiC monitors. Figure 1 depicts the equipment at the HTTL used to evaluate the SiC monitors. The SiC monitors are heated in the annealing furnace using isochronal temperature steps that, depending on customer needs, can range from 50 to 800 C. This furnace is located under a ventilation hood within the stainless steel enclosure. The ventilation system is activated during heating so that any released vapors are vented through this system. Annealing

  7. Intergranular attack and stress corrosion cracking of Alloy 600 in high-temperature caustic solutions containing contaminants

    SciTech Connect (OSTI)

    Bandy, R.; Roberge, R.; van Rooyen, D.

    1985-06-01

    Concentrated caustic is a primary cause of stress corrosion cracking and intergranular attack of Alloy 600 tubing in PWRs. However, temperature, electrochemical potential, stress, and metallurgical state all play a role. This study provides the quantitative evidence needed to develop models of crack growth and to devise effective countermeasures.

  8. Threshold of photoelectron emission from CN{sub x} films deposited at room temperature and at 500 deg. C

    SciTech Connect (OSTI)

    Sago, Genki; Li Wanyan; Goto, Keisuke; Ichikawa, Yo; Ishida, Yoshihisa; Kohiki, Shigemi

    2004-10-15

    The threshold of photoelectron emission was measured for amorphous CN{sub x} films deposited at room temperature (RT) and at 500 deg. C. The x values of the films deposited at RT and at 500 deg. C by magnetron sputtering of a graphite target in a mixed N{sub 2}/Ar gas were 0.6 and 0.3, respectively. Ratios of the sp{sup 2}- to sp{sup 3}-hybridized components of both C and N for the film deposited at 500 deg. C were larger by {approx_equal}4 times than those for the film deposited at RT. The onsets of the electron emission by photon irradiation were 5.0 and 4.7 eV for the films deposited at RT and at 500 deg. C, respectively.

  9. Geek-Up[3.4.2011]: 3,000+ MW and 2,500 Year-Old Greek Pottery

    Broader source: Energy.gov [DOE]

    Bonneville Power Administration celebrates big windy milestone and researchers SLAC National Accelerator Laboratory study the surfaces of 2,500 year old Greek pottery -- all in this week's Geek-Up.

  10. Experimental Determination of Phase Equilibria in the System H{sub 2}O-CO{sub 2}-NaCl at 0.5 Kb from 500 to 800C

    SciTech Connect (OSTI)

    Anovitz, L.M.

    2001-01-09

    An understanding of activity-composition (a/X) relations and phase equilibria for halite-bearing, mixed-species supercritical fluids is critically important to many geological and industrial applications. The authors have performed experiments on the phase equilibria of H{sub 2}O-CO{sub 2}-NaCl fluids from 500 C to 800 C at 500 bars, conditions of significant importance in studies of magma-hydrothermal systems, geothermal reservoirs and some ore deposits, to obtain highly accurate and precise data for this ternary system. These experiments are conducted using a double capsule technique. An excess of NaCl is placed in an inner Pt capsule, which is crimped shut and placed in an outer capsule containing H{sub 2}O and CO{sub 2}. During the experiment NaCl dissolves out of the inner capsule, and is deposited in the outer capsule during the quench. After the experiment the capsule is opened, and the amount of NaCl remaining in the inner capsule determined by dissolution. The difference between the initial and final amounts of NaCl in the inner capsule yields the solubility of NaCl at the P-T conditions of the experiment. At 500 C data from these experiments suggest that the vapor comer of the three-phase field lies near X(H{sub 2}O) = 0.760, X(NaCl) = 0.065, which is a significantly more water-rich composition than suggested by previous models. As expected, increasing temperature increases the solubility of NaCl in the NaCl-vapor field. For example, at intermediate H{sub 2}O/CO{sub 2} ratios the vapor field extends from approximately near X(H{sub 2}O) = 0.66, X(NaCl) = 0.06 at 500 C to near X(H{sub 2}O) = 0.65, X(NaCl) = 0.08 at 600 C.

  11. Intergranular attack of alloy 600: Simulation and remedial action tests: Final report

    SciTech Connect (OSTI)

    Daret, J.; Feron, D.

    1989-02-01

    The intergranular attack (IGA) that affects alloy 600 tubes in the tube sheet crevices of PWR steam generators is hard to simulate in laboratory studies. For this study, a special apparatus was designed with a range of representative materials, mechanical conditions and geometry. The design also took account of sludge piles, thermal fluxes and water chemistry. During a first series of seven model boiler tests, chemical parameters and test procedures were adjusted to finally obtain a field prototypical degradation of tubing over a significant length within the tube sheet crevice for the case of caustic pollution. IGA was not produced for the river water in-leakage case. A second series of model boiler tests also showed the possibility of producing a representative IGA by initially filling the tube sheet crevices with concentrated caustic solutions. A third series of five model boiler tests aimed at studying in the effectiveness of remedial actions on either virgin of IGA affected tubing. Tube sheet crevice flushing operations using the natural circulation procedure showed a poor efficiency for moving concentrated contaminants, but they succeeded in forcing chemicals additives (acetic acid or boric acid) within the non-occluded portions of crevices. This off-line treatment resulted in a reduction in the progression rate of the pre-existing IGA by a factor of 2 to 3. Simulation of this treatment on virgin material showed that this result was obtained because acetate or borate shifted the cation-to-anion equivalent ratio to well under one. However this off-line treatment could not prevent the occurrence of intergranular stress corrosion cracking (IGSCC) near the top of crevices, since caustic continued to hideout under full power operation. The best remedial action consisted of a combination of off-line and on-line boric acid treatment. IGSCC was prevented both on virgin and IGA affected tubes. 3 figs., 3 tabs.

  12. Model boiler testing to evaluate inhibitors for caustic induced stress corrosion cracking of Alloy 600 tubes

    SciTech Connect (OSTI)

    Daret, J.; Paine, J.P.N.; Partridge, M.J.

    1995-12-31

    A series of model boiler tests, using a mixture of precracked and non-precracked (virgin) tube-to-tube support plate intersections was performed. The testing supported the qualification of inhibitors for mitigating the secondary side corrosion of alloy 600 steam generator tubes. Many utilities suspect that the caustic impurities come from the feedwater. Candidate inhibitors included boric acid (as a reference), cerous acetate, and two forms of titanium dioxide: a laboratory produced titania-silica sol-gel, and manometer sized anatase The latter was combined with a 150 C pre-soaking with a titanium lactate, and was tested with and without a zeta potential treatment by sodium aluminate. Effectiveness of boric acid to prevent and retard caustic induced intergranular corrosion was confirmed in all crevice configurations (open and packed). The cerous acetate treatment multiplied by two to four the time necessary to detect a primary-to-secondary leak on virgin tubes, and reduced the propagation rate on precracked tubes. Cerium was found intimately mixed, as cerianite, with the free span and crevice deposits, when the crevices were sufficiently accessible. Due to its very low solubility and large particle size, the titania-silica sol-gel was unable to penetrate the crevices and had no effect on the degradation process. The nanometric particle size titania treatment and/or the preceding soaking with soluble titanium lactate drastically increased the titanium concentration in free span and open crevice deposit (with no added sodium aluminate, titania reacted with magnetite to form ilmenite) and showed undeniable capacity to prevent tubing degradation. Its effectiveness, in the case of packed crevices and for arresting cracks, was not so conclusive.

  13. Stress Corrosion Cracking and Non-Destructive Examination of Dissimilar Metal Welds and Alloy 600

    SciTech Connect (OSTI)

    Jackson, Deborah A.

    2002-07-01

    The United States Nuclear Regulatory Commission (USNRC) has conducted research since 1977 in the areas of environmentally assisted cracking and assessment and reliability of non-destructive examination (NDE). Recent occurrences of cracking in Alloy 82/182 welds and Alloy 600 base metal at several domestic and overseas plants have raised several issues relating to both of these areas of NRC research. The occurrences of cracking were identified by the discovery of boric acid deposits resulting from through-wall cracking in the primary system pressure boundary. Analyses indicate that the cracking has occurred due to primary water stress corrosion cracking (PWSCC) in Alloy 82/182 welds. This cracking has occurred in two different locations: in hot leg nozzle-to-safe end welds and in control rod drive mechanism (CRDM) nozzle welds. The cracking associated with safe-end welds is important due to the potential for a large loss of reactor coolant inventory, and the cracking of CRDM nozzle base metal and welds, particularly circumferential cracking of CRDM nozzle base metal, is important due to the potential for a control rod to eject resulting in a loss of coolant accident. The industry response in the U.S. to this cracking is being coordinated through the Electric Power Research Institute's Materials Reliability Project (EPRI-MRP) in a comprehensive, multifaceted effort. Although the industry program is addressing many of the issues raised by these cracking occurrences, confirmatory research is necessary for the staff to evaluate the work conducted by industry groups. Several issues requiring additional consideration regarding the generic implications of these isolated events have been identified. This paper will discuss the recent events of significant cracking in domestic and foreign plants, discuss the limitations of NDE in detecting SCC, identify deficiencies in information available in this area, discuss the USNRC approach to address these issues, and discuss the

  14. Rocky Flats 10 year plan: over 500 structures to be demolished

    SciTech Connect (OSTI)

    Evans, B.; Bengel, P.

    1997-03-01

    Rocky Flats Environmental Technology Site has prepared a Ten Year Plan (Plan) that demonstrates how the Site would achieve accelerated cleanup and rapidly reduce the risks the Site currently poses to its workers, the public, and the environment. A major element of the Plan is the decontamination and demolition of over 500 Site facilities, including all of the former nuclear production facilities, by the end of 2006. Facilities used for the storage of plutonium, treatment of low-level mixed waste, and several office building would remain until the plutonium is removed or there is no longer a need for the facility, in which case it would be demolished. While the Plan considers all aspects of the cleanup and closure, this paper focuses on the challenges posed by the removal of highly contaminated equipment and the demolition of structures. This paper describes near- term decommissioning projects as well as the long range plans and budgets. Cash flow ultimately controls schedule, and sharing of budget priorities among processing of special nuclear material, disposing of waste, and cleaning up the environment has to be juggled carefully to attain the goals of the Plan. The total cost of the Plan exceeds $5 billion, and over $1 billion will be spent on decommissioning activities. Following removal of the plutonium and the demolition of the plutonium storage and remaining Site facilities by the end of 2015, the cost to perform the long-term environmental monitoring at the Site is estimated to be $10 million per year.

  15. Measuring W photon couplings in a 500 GeV e sup + e sup - collider

    SciTech Connect (OSTI)

    Yehudai, E.

    1991-08-01

    The Standard Model gives definite predictions for the W-photon couplings. Measuring them would test an important ingredient of the model. In this work we study the capability of a 500 GeV e{sup +}e{sup {minus}} collider to measure these couplings. We study the most general C and P conserving WW{lambda} vertex. This vertex contains two free parameters, {kappa} and {lambda}. We look at three processes: e{sup +}e{sup {minus}} {yields} W{sup +}W{sup {minus}}, e{lambda} {yields} W{nu} and {lambda}{lambda} {yields} W{sup +}W{sup {minus}}. For each process we present analytical expressions of helicity amplitudes for arbitrary values of {kappa} and {lambda}. We consider three different sources for the initial photon(s). The first two are breamsstrahlung and beamstrahlung (photon radiation induced by the collective fields of the opposite bunch). Both occur naturally in the collider environment. The third is a photon beam generated by scattering low energy laser light off a high energy electron beam. We examine potential observables for each process, calculating their sensitivity to {kappa} and {lambda}, and estimating the accuracy with which they can be measured. Assuming Standard Model values are actually measured, we present the region in the {kappa}-{lambda} plane to which the W couplings can be restricted with a given confidence level. We find that combining the three processes, one can measure {kappa} and {lambda} with accuracy of 0.01--0.02.

  16. Imaging magnetic domain structure in sub-500 nm thin film elements

    SciTech Connect (OSTI)

    Kirk, K. J.; McVitie, S.; Chapman, J. N.; Wilkinson, C. D. W.

    2001-06-01

    Magnetic imaging in the transmission electron microscope (TEM) has been used to examine submicron elements with the aim of discovering down to what element size complex domain patterns can form. The elements were squares, circles, triangles, and pentagons in the size range 100{endash}500 nm and were made from 36 nm Co films or 8 nm Ni{sub 80}Fe{sub 20} (NiFe) with in-plane magnetization. The magnetic domain structures in these elements were imaged at high resolution using the differential phase contrast imaging mode in a TEM. Nonuniform magnetization structures were seen in the images. Vortices were present at remanence in all shapes of 36-nm-thick Co elements down to 100 nm size and in circular NiFe elements down to 116 nm diameter. Triangular NiFe elements did not have a vortex state at remanence, instead the magnetization curved round within the element but did not achieve complete flux closure. In simulations of square and circular NiFe elements, it was found that defects at the edges of the elements encouraged reversal by a vortex mechanism, whereas for simulated elements with no defects, reversal was by rotation and occurred at much lower fields. {copyright} 2001 American Institute of Physics.

  17. THE DISCOVERY OF BINARY WHITE DWARFS THAT WILL MERGE WITHIN 500 Myr

    SciTech Connect (OSTI)

    Kilic, Mukremin; Brown, Warren R.; Kenyon, S. J.; Allende Prieto, Carlos; Panei, J. A.

    2010-06-10

    We present radial velocity observations of four extremely low-mass (0.2 M {sub sun}) white dwarfs (WDs). All four stars show peak-to-peak radial velocity variations of 540-710 km s{sup -1} with 1.0-5.9 hr periods. The optical photometry rules out main-sequence companions. In addition, no millisecond pulsar companions are detected in radio observations. Thus, the invisible companions are most likely WDs. Two of the systems are the shortest period binary WDs yet discovered. Due to the loss of angular momentum through gravitational radiation, three of the systems will merge within 500 Myr. The remaining system will merge within a Hubble time. The mass functions for three of the systems imply companions more massive than 0.46 M {sub sun}; thus, those are carbon/oxygen core WDs. The unknown inclination angles prohibit a definitive conclusion about the future of these systems. However, the chance of a supernova Ia event is only 1%-5%. These systems are likely to form single R Coronae Borealis stars, providing evidence for a WD + WD merger mechanism for these unusual objects. One of the systems, SDSS J105353.89+520031.0, has a 70% chance of having a low-mass WD companion. This system will probably form a single helium-enriched subdwarf O star. All four WD systems have unusual mass ratios of {<=}0.2-0.8 that may also lead to the formation of AM CVn systems.

  18. Design and Fabrication of a Radiation-Hard 500-MHz Digitizer Using Deep Submicron Technology

    SciTech Connect (OSTI)

    K.K. Gan; M.O. Johnson; R.D. Kass; J. Moore

    2008-09-12

    The proposed International Linear Collider (ILC) will use tens of thousands of beam position monitors (BPMs) for precise beam alignment. The signal from each BPM is digitized and processed for feedback control. We proposed the development of an 11-bit (effective) digitizer with 500 MHz bandwidth and 2 G samples/s. The digitizer was somewhat beyond the state-of-the-art. Moreover we planned to design the digitizer chip using the deep-submicron technology with custom transistors that had proven to be very radiation hard (up to at least 60 Mrad). The design mitigated the need for costly shielding and long cables while providing ready access to the electronics for testing and maintenance. In FY06 as we prepared to submit a chip with test circuits and a partial ADC circuit we found that IBM had changed the availability of our chosen IC fabrication process (IBM 6HP SiGe BiCMOS), making it unaffordable for us, at roughly 3 times the previous price. This prompted us to change our design to the IBM 5HPE process with 0.35 µm feature size. We requested funding for FY07 to continue the design work and submit the first prototype chip. Unfortunately, the funding was not continued and we will summarize below the work accomplished so far.

  19. Demonstration of a 30-kW Microturbine with Heat Recovery in a 500-Soldier Barracks

    SciTech Connect (OSTI)

    Friedrich, Michele; Armstrong, Peter R.; Smith, David L.; Rowley, Steven

    2005-12-31

    A combined heat and power-configured microturbine system was evaluated as an alternative to grid-supplied electric power. While off-grid, the system provides auxiliary power for gas-fired boilers and a portion of the domestic hot water for a 500-man barracks and kitchen. One-time tests were made of sound levels, stack emissions and power quality. Steady-state generating capacity dropped faster than the ratings as the inlet air temperature approached 15°C, while generating efficiency, based on fuel higher heating value, did not drop as rapidly and was still almost 21% at 33°C. The microturbine must boost the fuel (natural gas) delivery pressure to 55 psig. During the one year of operation, four fuel compressors failed and there were repeated failures of the microturbine and heat recovery heat exchanger controls. Energy savings based on the measured performance and CY2003 utility rates were $2670 per year. This paper, which will be presented at the ASHRAE Annual Meeting in Orlando, Florida, Feb. 5-9, describes the results of this evaluation.

  20. Microstructural effects on microdeformation and primary-side stress corrosion cracking of Alloy 600 tubing: Final report

    SciTech Connect (OSTI)

    Bruemmer, S.M.; Charlot, L.A.; Henager, C.H. Jr.

    1987-05-01

    Microdeformation characteristics in Alloy 600 tubing have been examined after various tensile deformations. Microstructure developed during processing was found to control subsequent microdeformation behavior. Grain boundary carbides were the most effective source of dislocations, activating at lower macro-strains and continuing to operate at higher macro-strains than other sources. Ledges within grain boundaries, twin boundaries and matrix carbides also acted as dislocation sources. Most dislocation activity at low strains was confined to planar arrays. A conceptual model is presented to account for the effects of interfacial and matrix microstructure on microdeformation and primary-side SCC of Alloy 600 tubing. Microstructure is linked to IGSCC resistance through its influence on microdeformation behavior and the resultant crack-tip stress state. Dislocation source activity at grain interfaces is proposed to be a critical aspect controlling IGSCC susceptibility. Effective sources such as grain boundary carbides promote crack blunting, decrease the crack-tip stress state and increase resistance to cracking.

  1. The influence of dissolved hydrogen on primary water stress corrosion cracking of Alloy 600 at PWR steam generator operating temperatures

    SciTech Connect (OSTI)

    Jacko, R.J.; Economy, G.; Pement, F.W.

    1992-12-31

    PWR primary coolant chemistry uses an intentional dissolved hydrogen concentration of 20 to 50 ml (STP)/kg of water to effect a net suppression of oxygen-producing radiolysis, to minimize corrosion in primary loop materials and to maintain a low redox potential. Speculation has attended a possible influence of dissolved hydrogen on the kinetics of initiation of Primary Water Stress Corrosion Cracking (PWSCC) behavior of Alloy 600 steam generator tubing. Three series of experiments are presented for conditions in which the level of dissolved hydrogen was intentionally varied over the hydrogen and temperature ranges of interest for steam generator operation. No significant effect of dissolved hydrogen was found on PWSCC of Alloy 600.

  2. Initiation and propagation of stress-corrosion cracking of Alloy 600 in high-temperature water. [PWR

    SciTech Connect (OSTI)

    Bandy, R.; van Rooyen, D.

    1983-01-01

    Results of stress-corrosion cracking data are presented for Inconel 600 steam-generator tubing. U-bend, constant-load, and slow extension-rate tests are included. Arrhenius plots are presented for failure times vs inverse temperature for crack initiation and propagation. Effect of applied load is expressed in terms of log-log curves for failure times vs stress, and variations in environment and cold work are included. Microstructure and composition of oxide films on Inconel 600 surfaces were examined after exposure to pure water at 365/sup 0/C, and stripping with the bromine-methanol method. Results are discussed in terms of transient creep, film rupture and a mass-transport-limited anodic process.

  3. The structure and stability of aqueous rare-earth elements in hydrothermal fluids: New results on neodymium(III) aqua and chloroaqua complexes in aqueous solutions to 500 °C and 520 MPa

    SciTech Connect (OSTI)

    Mayanovic, R.A.; Anderson, A.J.; Bassett, W.A.; Chou, I.-M.

    2009-02-04

    X-ray absorption spectroscopy (XAS) measurements were made at the Nd L{sub 3}-edge on neodymium(III) aqua and chloroaqua complexes in low pH aqueous solutions from 25 to 500 C and up to 520 MPa. Analysis of the extended X-ray absorption fine structure of the XAS spectra measured from a 0.07 m Nd/0.16 m HNO{sub 3} aqueous solution reveals a contraction of the Nd-O distance of the Nd{sup 3+} aqua ion at a uniform rate of {approx} 0.013 {angstrom}/100 C and a uniform reduction of the number of coordinated H{sub 2}O molecules from 10.0 {+-} 0.9 to 7.4 {+-} 0.9 over the range from 25 to 500 C and up to 370 MPa. The rate of reduction of the first-shell water molecules with temperature for Nd{sup 3+} (26%) is intermediate between the rate for the Gd{sup 3+} aqua ion (22% from 25 to 500 C) and the rates for the Eu{sup 3+} (29% from 25 to 400 C) and the Yb{sup 3+} aqua ions (42% from 25 to 500 C) indicating an intermediate stability of the Nd{sup 3+} aqua ion consistent with the tetrad effect. Nd L{sub 3}-edge XAS measurements of 0.05 m NdCl{sub 3} aqueous solution at 25 to 500 C and up to 520 MPa show that stepwise inner-sphere complexes most likely of the type Nd(H{sub 2}O){sub {delta}-n}Cl{sub n}{sup +3-n} occur in the solution at elevated temperatures, where {delta} {approx} 9 at 150 C decreasing to {approx} 6 at 500 C and the number of chloride ions (n) of the chloroaqua complexes increases uniformly with temperature from 1.2 {+-} 0.2 to 2.0 {+-} 0.2 in the solution upon increase of temperature from 150 to 500 C. Conversely, the number of H{sub 2}O ligands of Nd(H{sub 2}O){sub {delta}-n}Cl{sub n}{sup +3-n} complexes is uniformly reduced with temperature from 7.5 {+-} 0.8 to 3.7 {+-} 0.3 in the aqueous solution, in the same temperature range. These data show greater stability of neodymium(III) than gadolinium(III) and ytterbium(III) chloride complexes in low pH aqueous solutions at elevated temperatures. Our data suggest a greater stability of aqueous light REE than

  4. Effects of shot peening on corrosion and stress corrosion cracking behaviors of sensitized Alloy 600 in thiosulfate solution

    SciTech Connect (OSTI)

    Tsai, W.T.; Chang, C.S.; Lee, J.T. . Dept. of Materials Science and Engineering)

    1994-02-01

    Effects of shot peening on the corrosion and stress corrosion cracking (SCC) behaviors of sensitized alloy 600 (UNSN06600) were studied. Electrochemical potentiokinetic reactivation (EPR) tests in 0.01 M sulfuric acid (H[sub 2]SO[sub 4]) + 0.001 M potassium thiocyanate (KSCN) solution and immersion tests in boiling 25% nitric acid (HNO[sub 3]) solution were used to evaluate the effect of heat treatment on the degree of sensitization of alloy 600. Potentiodynamic polarization tests in 0.01 M sodium thiosulfate (Na[sub 2]S[sub 2]O[sub 3]) solution at 95 C revealed shot peening increased the anodic current density (CD) of the alloy. However, SCC tests using U-bend specimens indicated shot peening substantially increased the crack initiation time in the same environment. The delayed crack initiation of SCC for shot-peened alloy 600, which is potentially dependent, was attributed to the presence of compressive residual stresses and the severely deformed surface microstructure.

  5. B&W Y-12 donates $2,500 to MMC Hospitality House | Y-12 National Security

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Complex MMC Hospitality House Posted: January 27, 2014 - 1:35pm B&W Y-12 donated $2,500 to Oak Ridge Methodist Medical Center's Hospitality House. B&W Y-12 Director of Public Affairs Bill Reis, right, hands a $2,500 donation to Mike Belbeck, Methodist Medical Center's President and Chief Administrative Officer. The funds will go toward MMC's Hospitality Houses, which provide temporary lodging for patients and families who travel to Oak Ridge for extended medical treatment

  6. A lead-before-break strategy for primary heat transport piping of 500 MWe Indian PHWR

    SciTech Connect (OSTI)

    Chattopadhyay, J.; Dutta, B.K.; Kushwaha, H.S.

    1997-04-01

    Leak-Before-Break (LBB) is being used to design the primary heat transport piping system of 500 MWe Indian Pressurized Heavy Water Reactors (IPHWR). The work is categorized in three directions to demonstrate three levels of safety against sudden catastrophic break. Level 1 is inherent in the design procedure of piping system as per ASME Sec.III with a well defined factor of safety. Level 2 consists of fatigue crack growth study of a postulated part-through flaw at the inside surface of pipes. Level 3 is stability analysis of a postulated leakage size flaw under the maximum credible loading condition. Developmental work related to demonstration of level 2 and level 3 confidence is described in this paper. In a case study on fatigue crack growth on PHT straight pipes for level 2, negligible crack growth is predicted for the life of the reactor. For level 3 analysis, the R6 method has been adopted. A database to evaluate SIF of elbows with throughwall flaws under combined internal pressure and bending moment has been generated to provide one of the inputs for R6 method. The methodology of safety assessment of elbow using R6 method has been demonstrated for a typical pump discharge elbow. In this analysis, limit load of the cracked elbow has been determined by carrying out elasto-plastic finite element analysis. The limit load results compared well with those given by Miller. However, it requires further study to give a general form of limit load solution. On the experimental front, a set of small diameter pipe fracture experiments have been carried out at room temperature and 300{degrees}C. Two important observations of the experiments are - appreciable drop in maximum load at 300{degrees}C in case of SS pipes and out-of-plane crack growth in case of CS pipes. Experimental load deflection curves are finally compared with five J-estimation schemes predictions. A material database of PHT piping materials is also being generated for use in LBB analysis.

  7. A 200-A, 500-Hz, triangle current-wave modulator and magnet used for particle beam rastering

    SciTech Connect (OSTI)

    Rose, C.R.; Shafer, R.E.

    1997-10-01

    This paper describes a simple 2D beam-rastering system to uniformly spread a 100-mA 6.7-MeV cw proton beam over a 50-cm by 50-cm beam stop. The basic circuit uses a 20-mF capacitor bank, a IGBT (insulated gate bipolar transistor) full-wave inverter, and a 1-mH ferrite dipole magnet to produce a {+-} 500-Gauss peak triangular-waveform deflection field at 500 Hz. A dc input voltage of 200 volts at 2.6 amps (520 watts) produces a 160-ampere peak-to-peak triangular current waveform in the ferrite magnet at 500 Hz. For dual-axis rastering, two ferrite dipoles are used, one at 500 Hz, and the other at 575 Hz, to produce a uniform 2D beam distribution at the beam stop. The paper will discuss the IGBT modulator and ferrite deflector in detail, including current and voltage waveforms, and the ferrite magnet B-dot (dB/dt) signal.

  8. The Case for a 500 GeV e{sup +}e{sub {minus}} Linear Collider

    SciTech Connect (OSTI)

    Peskin, Michael E

    2000-07-12

    Several proposals are being developed around the world for an e{sup +}e{sub {minus}} linear collider with an initial center of mass energy of 500 GeV. In this paper, the authors discuss why a project of this type deserves priority as the next major initiative in high energy physics.

  9. Upgrading a high-throughput spectrometer for high-frequency (&lt;400 kHz) measurements

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Upgrading a high-throughput spectrometer for high-frequency ( T. Nishizawa, M. D. Nornberg, D. J. Den Hartog, and D. Craig Citation: Review of Scientific Instruments 87, 11E530 (2016); doi: 10.1063/1.4960073 View online: http://dx.doi.org/10.1063/1.4960073 View Table of Contents: http://scitation.aip.org/content/aip/journal/rsi/87/11?ver=pdfcov Published by the AIP Publishing Articles you may be interested in Observation of 20-400 kHz fluctuations in the U-3M torsatron Phys. Plasmas 23, 022506

  10. United States Environmental Monitoring EPA-600/4-81-047 Environmental Protection Systems Laboratory DOE/DP/00539-043

    Office of Legacy Management (LM)

    EPA-600/4-81-047 Environmental Protection Systems Laboratory DOE/DP/00539-043 Agency P.O. Box 15027 June 1981 Las Vegas NV 891 14 Research and Development Offsite Environmental Monitoring Report Radiation Monitoring Around United States Nuclear Test Areas, Calendar Year 1980 prepared for the Nevada Operations Office U.S. Department of Energy This page intentionally left blank EPA-60014-81-047 DOE/DP/00539-043 June 1981 OFFSITE ENVIRONMENTAL MONITORING REPORT Radiation moni t o r i ng around U n

  11. Predicting susceptibility of alloy 600 to intergranular stress corrosion cracking using a modified electrochemical potentiokinetic reactivation test

    SciTech Connect (OSTI)

    Ahn, M.K.; Kwon, H.S.; Lee, J.H.

    1995-06-01

    Modified double-loop electrochemical potentiokinetic reactivation (DL-EPR) tests were applied to evaluate the degree of sensitization (DOS) for alloy 600 aged at 700 C. Results of the modified DL-EPR test were compared to intergranular stress corrosion cracking (IGSCC) susceptibilities determined in deaerated 0.01 M sodium tetrathionate under deformation at a constant strain rate of 0.93 {times} 10{sup {minus}6}/s. By analyzing the effects of solution concentration, temperature, and scan rate on the electrochemical response in the EPR tests and the morphologies, the optimal modified DL-EPR test condition for alloy 600 was obtained in 0.01 M sulfuric acid + 10 ppm potassium thiocyanate at 25 C and at a scan rate of 0.5 mV/s. The standard DL-EPR test, performed under conditions of 0.5 M H{sub 2}SO{sub 4} + 0.01 M KCNS at 30 C and a scan rate of 1.67 mV/s, provided very poor discriminating power for various DOS of alloy 600 because general and pitting corrosion occurred, in addition to intergranular corrosion. The modified test, however, was highly discriminating because of its highly selective corrosion attack at grain boundaries. IGSCC occurred in samples of alloy 600 aged for < 20 h, and susceptibility to IGSCC{sub s} increased with decreasing aging times up to 1 h, showing maximum IGSCC{sub s} in the sample aged for 1 h. IGSCC{sub s} for the alloy was found to be associated closely with the chromium-depleted profile across grain boundaries. The deeper and narrower chromium-depleted zone produced greater IGSCC{sub s}. It was demonstrated that DOS measured by the modified DL-EPR test was correlated more closely with IGSCC{sub s} than was DOS measured by the standard EPR test. This correlation resulted from the fact that the modified EPR test selectively attacked the more deeply chromium-depleted regions in comparison to the standard EPR test.

  12. Stress corrosion of alloys 600 and 690 in acidic sulfate solutions at elevated temperatures. Final report. [PWR

    SciTech Connect (OSTI)

    Newman, J.F.

    1983-10-01

    EPRI project RP 1171-1 demonstrated that alloy 600 was susceptible to stress corrosion cracking in sulfate environments during constant extension rate testing. The current project has extended that investigation to determine the influence of alloy grain size, sensitization, solution pH and temperature. Stress corrosion in very dilute sulfate solutions and the susceptibility of alloy 690 have also been studied. Data have been obtained chiefly by constant extension rate testing using tensile specimens, and by the constant displacement testing of C-rings.

  13. Search for neutrino oscillations by detecting UNK-1 600-GeV neutrino beams at Gran Sasso (Italy)

    SciTech Connect (OSTI)

    Vasil`ev, P.S.; Kuznetsov, A.E.; Kuznetsov, E.P.

    1995-12-01

    The possibility of formation of neutrino beams from the 600-GeV UNK-1 accelerator toward Gran Sasso (Italy) and of study neutrino oscillations with the ICARUS detector is demonstrated. The proposed experiment is sensitive to {Delta}m{sup 2} values down to 10{sup -3} eV{sup 2} at maximum neutrino mixing and to sin{sup 2}2{theta} values down to 6 x 10{sup -3} at {Delta}m{sup 2} {approximately} 2 x 10{sup -2} eV{sup 2}. 21 refs., 6 figs., 3 tabs.

  14. Compatibility of an Ultraselective Microcatheter and Epirubicin Loaded 300–500-μm DC Bead in Ex Vivo Study

    SciTech Connect (OSTI)

    Fukuoka, Yasushi Tanaka, Toshihiro Nishiofuku, Hideyuki Sato, Takeshi Kichikawa, Kimihiko

    2015-10-15

    PurposeThe purpose of this study is to examine whether epirubicin loaded DC Bead 300–500 μm in size can pass through a 1.8-Fr ultraselective microcatheter in ex vivo study.MethodsEpirubicin (25 mg/1 mL) loaded 100–300 and 300–500 μm DC Bead were tested. Both sizes were diluted 5, 10, and 30 times using contrast material. Ultraselective microcatheter with the outer diameter of 1.8 Fr and the inner diameter of .017 inch (431.8 μm) was used. The diluted DC Bead was injected at a speed of 1 mL/min, and the pressure was continuously measured. The microspheres’ shapes after ejection were observed by a stereomicroscope.ResultsThe maximum pressure of contrast material alone was 8.40 ± 0.21 psi. The maximum pressure in 5, 10, and 30 times dilution groups of 100–300 μm were 9.67 ± 1.18, 9.25 ± 0.25, and 9.71 ± 0.28 psi, respectively, whereas 21.10 ± 10.2, 10.48 ± 2.14, 10.09 ± 0.37 psi, respectively in 300–500 μm groups. The maximum pressure in 5 times dilution group of 300–500 μm was significantly higher than the other groups (P < 0.05). In 300–500 μm, 4 of 10 measurements showed high pressure over 24 psi (the maximum value was 43.5 psi) in 5 times dilution group, whereas in 10 times and 30 times dilution groups, all measurements showed less than 12 psi. No damages of microspheres were found.ConclusionsEpirubicin loaded DC Bead 300–500 μm in size can pass through a 1.8-Fr ultraselective microcatheter. To avoid high resistance due to microspheres’ aggregation, dilution more than 10 times is needed.

  15. Irradiation creep of various ferritic alloys irradiated at {approximately}400{degrees}C in the PFR and FFTF reactors

    SciTech Connect (OSTI)

    Toloczko, M.B.; Garner, F.A.; Eiholzer, C.R.

    1997-04-01

    Three ferritic alloys were irradiated in two fast reactors to doses of 50 dpa or more at temperatures near 400{degrees}C. One martensitic alloy, HT9, was irradiated in both the FFTF and PFR reactors. PFR is the Prototype Fast Reactor in Dourneay, Scotland, and FFTF is the Fast Flux Test Facility in Richland, WA. D57 is a developmental alloy that was irradiated in PFR only, and MA957 is a Y{sub 2}O{sub 3} dispersion-hardened ferritic alloy that was irradiated only in FFTF. These alloys exhibited little or no void swelling at {approximately}400{degrees}C. Depending on the alloy starting condition, these steels develop a variety of non-creep strains early in the irradiation that are associated with phase changes. Each of these alloys creeps at a rate that is significantly lower than that of austenitic steels irradiated in the same experiments. The creep compliance for ferritic alloys in general appears to be {approximately}0.5 x 10{sup {minus}6} MPa{sup {minus}1} dpa{sup {minus}1}, independent of both composition and starting state. The addition of Y{sub 2}O{sub 3} as a dispersoid does not appear to change the creep behavior.

  16. The effects of chemical factors on stress corrosion of Alloy 600 exposed to the cooling medium in pressurized water reactors

    SciTech Connect (OSTI)

    Berge, Ph.; Keroulas, F. de; Menet, O.; Rocher, A.; Pitner, P.; Gelpi, A.; Pinard-Legry, G.

    1992-12-31

    The effects of chemical factors in reducing stress corrosion of Alloy 600 in a primary coolant medium were investigated in France as part of a test program undertaken by three laboratories (EDF, FRAMATOME and CEA) on tubes with differing sensitivity to corrosion. Studied parameters were type of Alloy 600 material, temperature, lithium concentration and pH. The effect of each parameter was first estimated separately by qualitative analysis and the parameter groups which best describe the corrosion phenomenon were then defined. The preponderant effect of increasing the temperature (by 40{degrees}C) and the type of material were confirmed, as was that of the boron and lithium concentrations. The risk of cracking increases with lithium content but the phenomenon reverses at high concentrations. The effect of pH variations is mainly reflected in variations in the lithium content. A quantitative study was then carried out to assess the effect of each parameter in terms of risk and time to cracking in a given reference medium. A model of the chemical effects is proposed, based on the mechanism involving dissolution-repassivation of the metal after failure of the passive film during the phase when cracks propagate slowly. This allows a quantitative approach to the effects of hydrogen and the other chemical parameters involved and the results are compared with those of the statistical model.

  17. Mechanisms of hydrogen-induced intergranular stress corrosion cracking of Alloy 600 in high-temperature water/steam

    SciTech Connect (OSTI)

    Shen, C.H.

    1989-01-01

    Intergranular stress-corrosion cracking (IGSCC) of Alloy 600 in high-temperature deaerated water or steam has been termed Hydrogen Induced IGSCC. It is suggested here that these cracks are initiated by the nucleation of a high density of bubbles on the grain boundary under the combined action of the applied stress and high-pressure methane formed from carbon in solution reacting with hydrogen injected by corrosion. The bubbles then grow together by grain-boundary diffusion to give local failure. This agrees with the observations made using the electron microscope and two-stage replicas, namely the subsurface formation of closely spaced (0.2 {mu}m) bubbles along boundaries, and the growth of these into fine cracks before they open up to communicate with the corroding atmosphere. The kinetics of this process are examined and shown to be in quantitative agreement with several experimental observations. This mechanism involves no dissolution of the metal, the only role of corrosion being the injection of hydrogen at a high fugacity. It also predicts an activation energy essentially equal to that for grain-boundary diffusion of nickel in the Alloy 600 grain boundary. The activation energy for grain-boundary self-diffusion in nickel is 115 kJ/mol.

  18. Tests with Inconel 600 to obtain quantitative stress-corrosion cracking data for evaluating service performance. [PWR

    SciTech Connect (OSTI)

    Bandy, R.; van Rooyen, D.

    1982-09-01

    Inconel 600 tubes in pressurized water reactor (PWR) steam generators form a pressure boundary between radioactive primary water and secondary water which is converted to steam and used for generating electricity. Under operating conditions the performance of alloy 600 has been good, but with some occasional small leaks resulting from stress corrosion cracking (SCC), related to the presence of unusually high residual or operating stresses. The suspected high stresses can result from either the deformation of tubes during manufacture, or distortion during abnormal conditions such as denting. The present experimental program addresses two specific conditions, i.e., (1) where deformation occurs but is no longer active, such as when denting is stopped and (2) where plastic deformation of the metal continues, as would occur during denting. Laboratory media consist of pure water as well as solutions to simulate environments that would apply in service; tubing from actual production is used in carrying out these tests. The environments include both normal and off chemistries for primary and secondary water. The results reported here were obtained in several different tests. The main ones are (1) split tube reverse U-bends, (2) constant extension rate tests (CERT), and (3) constant load. The temperature range covered is 290 to 365/sup 0/C.

  19. EA-1679: Grand Coulee's Third Powerplant 500-kV Transmission Line Replacement Project, Grant and Okanogon Counties, Washington

    Broader source: Energy.gov [DOE]

    This EA evaluates potential environmental impacts from the construction and operation of six new 500-kV overhead transmission lines to replace six existing underground lines at Grand Coulee Dam. DOE’s Bonneville Power Administration (BPA), a cooperating agency, was asked by the U. S. Department of the Interior’s Bureau of Reclamation to design and construct the proposed new transmission lines. A Finding of No Significant Impact was issued by BPA in December 2011.

  20. Highly resistive annealed low-temperature-grown InGaAs with sub-500 fs carrier lifetimes

    SciTech Connect (OSTI)

    Baker, C.; Gregory, I.S.; Tribe, W.R.; Bradley, I.V.; Evans, M.J.; Linfield, E.H.; Missous, M.

    2004-11-22

    We have optimized low-temperature-grown In{sub 0.3}Ga{sub 0.7}As for use in ultrafast photoconductive devices. Using low temperature ex situ annealing techniques, we have produced a photoconductive material that is highly resistive ({approx}10{sup 4} {omega} cm), has sub-500 fs carrier trapping lifetimes, and is matched to 1.06 {mu}m laser excitation.

  1. Heavy duty insulator assemblies for 500-kV bulk power transmission line with large diameter octagonalbundled conductor

    SciTech Connect (OSTI)

    Tsujimoto, K.; Hayase, I.; Hirai, J.; Inove, M.; Naito, K.; Yukino, T.

    1982-11-01

    This paper describes the design procedure and the results of field tests on mechanical performances of insulator assemblies newly developed to support octagonal-bundled conductors for 500-kV bulk power transmission. Taking account of conductor-motion-induced peak tensile load, fatigue, torsional torque and others, a successful design has been achieved in two prototype assemblies for such heavy mechanical duties as encountered during conductor galloping or swing. This has been proved throughout three years of the field tests.

  2. Intergranular stress corrosion cracking initiation and growth in mill-annealed Alloy 600 tubing in high-temperature caustic

    SciTech Connect (OSTI)

    Brisson, B.W.; Ballinger, R.G.; McIlree, A.R.

    1998-07-01

    Historically, pressurized water reactor (PWR) steam generator (SG) reliability has been dominated by degradation of alloy 600 (UNS N06600) tubing material. Stress corrosion cracking (SCC) crack initiation and crack growth rates (CGR) were measured in mill-annealed alloy 600 (UNS N06600) tubing as a function of the stress intensity factor (K) in 10% caustic at 315 C. Tests were conducted using internally pressurized smooth and precracked tubing. Samples were polarized to 150 mV (precracked tube test) or 225 mV (initiation test) with respect to a nickel electrode. Crack initiation and growth from the external tube surface were monitored using a multifrequency alternating current (AC) potential drop system. The AC potential drop system allowed detection of initiation from a smooth surface as well as the monitoring of crack extension in real time. In the case of precracked sample tests, the sample was precracked in fatigue from a sharp v-notch. CGR were obtained over the K range between 4 MPa{radical}m and 18 MPa{radical}m. Values for K were estimated based upon fractographic analysis of samples after testing and an estimate of the K-solution for a thin-walled tube. Average CGR ranged from 2 mm/y to 14 mm/y. CGR determined in this investigation represent the first SCC CGR data obtained in high-temperature caustic using actual steam generator tubing. Growth rates obtained fell within the overall range of the existing database for CGR (da/dt) in alloy 600. The data and analysis suggested a threshold value of K for K-driven crack growth of {approx} 4 MPa{radical}m. However, since the scatter in existing data is very large and the conditions for most of the data are poorly known or not known at all, this was surprising. More importantly, from the standpoint of life prediction, it was observed that da/dt responded to and was a function of K for cracks as small as 0.2 mm in depth, and probably smaller.

  3. REVIEW REPORT: BUILDING C-400 THERMAL TREATMENT 90 PERCENT REMEDIAL DESIGN REPORT AND SITE INVESTIGATION, PGDP, PADUCAH, KENTUCKY

    SciTech Connect (OSTI)

    Looney, B; Jed Costanza, J; Eva Davis, E; Joe Rossabi, J; Lloyd Stewart, L; Hans Stroo, H

    2007-08-15

    On 9 April 2007, the U.S. Department of Energy (DOE) Headquarters, Office of Soil and Groundwater Remediation (EM-22) initiated an Independent Technical Review (ITR) of the 90% Remedial Design Report (RDR) and Site Investigation (RDSI) for thermal treatment of trichloroethylene (TCE) in the soil and groundwater in the vicinity of Building C-400 at the Paducah Gaseous Diffusion Plant (PGDP). The general ITR goals were to assess the technical adequacy of the 90% RDSI and provide recommendations sufficient for DOE to determine if modifications are warranted pertaining to the design, schedule, or cost of implementing the proposed design. The ultimate goal of the effort was to assist the DOE Paducah/Portsmouth Project Office (PPPO) and their contractor team in ''removing'' the TCE source zone located near the C-400 Building. This report provides the ITR findings and recommendations and supporting evaluations as needed to facilitate use of the recommendations. The ITR team supports the remedial action objective (RAO) at C-400 to reduce the TCE source area via subsurface Electrical Resistance Heating (ERH). Further, the ITR team commends PPPO, their contractor team, regulators, and stakeholders for the significant efforts taken in preparing the 90% RDR. To maximize TCE removal at the target source area, several themes emerge from the review which the ITR team believes should be considered and addressed before implementing the thermal treatment. These themes include the need for: (1) Accurate and site-specific models as the basis to verify the ERH design for full-scale implementation for this challenging hydrogeologic setting; (2) Flexible project implementation and operation to allow the project team to respond to observations and data collected during construction and operation; (3) Defensible performance metrics and monitoring, appropriate for ERH, to ensure sufficient and efficient clean-up; and (4) Comprehensive (creative and diverse) contingencies to address the

  4. Effects of solar ultraviolet photons on mammalian cell DNA. [UVA (320-400 nm):a2

    SciTech Connect (OSTI)

    Peak, M.J.; Peak, J.G.

    1991-01-01

    This document presents information on the possible mechanisms of carcinogenesis caused by UVA (ultraviolet radiation in the 320--400 nm region). Most studies showing the carcinogenic effects of ultraviolet light have concentrated on UVB (280--320 nm). UVA had been considered harmless even though it penetrates biological tissues better than UVB. Recently, it has become apparent that UVA is also capable of causing damage to cellular DNA. This was unexpected because the DNA UV absorption spectrum indicates a negligible probability that photons of wavelengths longer than 320 nm will be directly absorbed. The most common defects induced in DNA by UVB are pyrimidine photoproducts, such as thymidine dimers. UVA photons produce defects resembling those caused by ionizing radiations: single- and double-strand breaks, and DNA-protein crosslinks. This paper also discusses the role of DNA repair mechanisms in UVA-induced defects and the molecular mechanisms of UVA damage induction. 38 refs. (MHB)

  5. Observation of parametric X-rays produced by 400 GeV/c protons in bent crystals

    SciTech Connect (OSTI)

    Scandale , W.; Robert-Demolaize, G.; Arduini, G.; Assmann, R.; Cerutti, F. et al

    2011-05-30

    Spectral maxima of parametric X-ray radiation (PXR) produced by 400 GeV/c protons in bent silicon crystals aligned with the beam have been observed in an experiment at the H8 external beam of the CERN SPS. The total yield of PXR photons was about 10{sup -6} per proton. Agreement between calculations and the experimental data shows that the PXR kinematic theory is valid for bent crystals with sufficiently small curvature as used in the experiment. The intensity of PXR emitted from halo protons in a bent crystal used as a primary collimator in a circular accelerator may be considered as a possible tool to control its crystal structure, which is slowly damaged because of irradiation. The intensity distribution of PXR peaks depends on the crystal thickness intersected by the beam, which changes for different orientations of a crystal collimator. This dependence may be used to control crystal collimator alignment by analyzing PXR spectra produced by halo protons.

  6. Observation of Parametric X-Rays Produced by 400-GeV/C Protons in Bent Crystals

    SciTech Connect (OSTI)

    Scandale, W.; Arduini, G.; Assmann, R.; Cerutti, F.; Gilardoni, S.; Christiansen, J.; Laface, E.; Losito, R.; Masi, A.; Metral, E.; Mirarchi, D.; Montesano, S.; Previtali, V.; Redaelli, S.; Valentino, G.; Schoofs, P.; Smirnov, G.; Tlustos, L.; Bagli, E.; Baricordi, S.; Dalpiaz, P.; /Ferrara U. /INFN, Ferrara /Ferrara U. /INFN, Ferrara /Ferrara U. /INFN, Ferrara /Ferrara U. /INFN, Ferrara /Frascati /Frascati /Frascati /INFN, Legnaro /INFN, Legnaro /INFN, Legnaro /INFN, Legnaro /INFN, Legnaro /INFN, Legnaro /INFN, Rome /INFN, Rome /INFN, Rome /INFN, Rome /INFN, Naples /Serpukhov, IHEP /Serpukhov, IHEP /Serpukhov, IHEP /Serpukhov, IHEP /Serpukhov, IHEP /Dubna, JINR /Dubna, JINR /St. Petersburg, INP /St. Petersburg, INP /St. Petersburg, INP /St. Petersburg, INP /Imperial Coll., London /Imperial Coll., London /Imperial Coll., London /Imperial Coll., London /Imperial Coll., London /Imperial Coll., London /Imperial Coll., London /Imperial Coll., London /Brookhaven /SLAC /SLAC /SLAC /IPTP, Dubna /Tomsk Polytechnic U. /Tomsk Polytechnic U.

    2012-05-07

    Spectral maxima of parametric X-ray radiation (PXR) produced by 400 GeV/c protons in bent silicon crystals aligned with the beam have been observed in an experiment at the H8 external beam of the CERN SPS. The total yield of PXR photons was about 10{sup -6} per proton. Agreement between calculations and the experimental data shows that the PXR kinematic theory is valid for bent crystals with sufficiently small curvature as used in the experiment. The intensity of PXR emitted from halo protons in a bent crystal used as a primary collimator in a circular accelerator may be considered as a possible tool to control its crystal structure, which is slowly damaged because of irradiation. The intensity distribution of PXR peaks depends on the crystal thickness intersected by the beam, which changes for different orientations of a crystal collimator. This dependence may be used to control crystal collimator alignment by analyzing PXR spectra produced by halo protons.

  7. Deuterated palladium at temperatures from 4. 3 to 400 K and pressures to 105 kbar: Search for cold fusion

    SciTech Connect (OSTI)

    Silvera, I.F.; Moshary, F. )

    1990-11-15

    We have studied a sample of deuterated palladium at pressures up to 105 kbar and temperatures from 4.3 to 400 K in an effort to detect cold fusion. A (D)/(Pd) concentration of 1.34{plus minus}0.1 was achieved. No evidence of cold fusion was found with a limit of 2.5{times}10{sup {minus}18} fusions (DD pair){sup {minus}1} s{sup {minus}1} from neutron detection and 1.5{times}10{sup {minus}8} fusions (DD pair){sup {minus}1} s{sup {minus}1} from detection of possible heating; a {gamma}-ray detector showed no evidence of {gamma} rays differing from background.

  8. Virginia Underground Natural Gas Storage Capacity

    U.S. Energy Information Administration (EIA) Indexed Site

    9,500 9,500 9,500 9,500 9,500 9,500 2002-2016 Total Working Gas Capacity 5,400 5,400 5,400 5,400 5,400 5,400 2012-2016 Total Number of Existing Fields 2 2 2 2 2 2

  9. Radioactive occurrences in veins and igneous and metamorphic rocks of New Mexico with annotated bibliography. [Over 600 citations

    SciTech Connect (OSTI)

    McLemore, V. T.

    1982-01-01

    From an extensive literature search and field examination of 96 nonsandstone radioactive occurrences, the author compiled an annotated bibliography of over 600 citations and a list of 327 radioactive occurrences in veins and igneous and metamorphic rocks of New Mexico. The citations are indexed by individual radioactive occurrence, geographic area, county, fluorspar deposits and occurrences, geochemical analyses, and geologic maps. In addition, the geology, mineralization, and uranium and thorium potential of 41 geographic areas in New Mexico containing known radioactive occurrences in veins and igneous and metamorphic rocks or that contain host rocks considered favorable for uranium or thorium mineralization are summarized. A list of aerial-radiometric, magnetic, hydrogeochemical, and stream-sediment survey reports is included.

  10. Evaluation and Repair of Primary Water Stress Corrosion Cracking in Alloy 600/182 Control Rod Drive Mechanism Nozzles

    SciTech Connect (OSTI)

    Frye, Charles R.; Arey, Melvin L. Jr.; Robinson, Michael R.; Whitaker, David E.

    2002-07-01

    In February 2001, a routine visual inspection of the reactor vessel head of Oconee Nuclear Station Unit 3 identified boric acid crystals at nine of sixty-nine locations where control rod drive mechanism housings (CRDM nozzles) penetrate the head. The boric acid deposits resulted from primary coolant leaking from cracks in the nozzle attachment weld and from through-thickness cracks in the nozzle wall. A general overview of the inspection and repair process is presented and results of the metallurgical analysis are discussed in more detail. The analysis confirmed that primary water stress corrosion cracking (PWSCC) is the mechanism of failure of both the Alloy 182 weld filler material and the alloy 600 wrought base material. (authors)

  11. M400.pdf

    National Nuclear Security Administration (NNSA)

  12. Enhanced High Harmonic Generation from Multiply Ionized Argon above 500 eV through Laser Pulse Self-Compression

    SciTech Connect (OSTI)

    Arpin, P.; Popmintchev, T.; Kapteyn, H. C.; Murnane, M. M.; Wagner, N. L.; Cohen, O.

    2009-10-02

    By combining laser pulse self-compression and high harmonic generation within a single waveguide, we demonstrate high harmonic emission from multiply charged ions for the first time. This approach enhances the laser intensity and counteracts ionization-induced defocusing, extending the cutoff photon energy in argon above 500 eV for the first time, with higher spectral intensity and cutoff energy than He for the same input laser parameters. This Letter demonstrates a pathway for extending high harmonic emission to very high photon energies using large, multiply charged, ions with high ionization potentials.

  13. Performance of the beam chamber vacuum system of K = 500 cyclotron at Variable Energy Cyclotron Centre Kolkata

    SciTech Connect (OSTI)

    Pal, Gautam DuttaGupta, Anjan; Chakrabarti, Alok

    2014-07-15

    The beam chamber of Variable Energy Cyclotron Centre, Kolkata's K = 500 superconducting cyclotron is pumped by liquid helium cooled cryopanel with liquid nitrogen cooled radiation shield. Performance of the vacuum system was evaluated by cooling the cryopanel assembly with liquid nitrogen and liquid helium. Direct measurement of beam chamber pressure is quite difficult because of space restrictions and the presence of high magnetic field. Pressure gauges were placed away from the beam chamber. The beam chamber pressure was evaluated using a Monte Carlo simulation software for vacuum system and compared with measurements. The details of the vacuum system, measurements, and estimation of pressure of the beam chamber are described in this paper.

  14. Architecture and technology of 500 Msample/s feedback systems for control of coupled-bunch instabilities

    SciTech Connect (OSTI)

    Teytelman, Dmitry

    2000-03-30

    Feedback control of coupled-bunch instabilities presents many challenges. Control bandwidths up to 250 MHz are required to damp all of the unstable coupled-bunch modes in recent accelerators. A digital parallel-processing array with 80 DSPs has been developed to control longitudinal instabilities in PEP-II/ALS/DA NE machines. Here the authors present a description of the architecture as well as the technologies used to implement 500 Msample/s real-time control system with 2,000 FIR filtering channels. Algorithms for feedback control, data acquisition, and analysis are described and measurements from ALS are presented.

  15. The results of systems tests of the 500 kV busbar controllable shunting reactor in the Tavricheskaya substation

    SciTech Connect (OSTI)

    Gusev, S. I.; Karpov, V. N.; Kiselev, A. N.; Kochkin, V. I.

    2009-09-15

    The results of systems tests of the 500 kV busbar magnetization-controllable shunting reactor (CSR), set up in the Tavricheskaya substation, including measurements of the quality of the electric power, the harmonic composition of the network currents of the reactor for different values of the reactive power consumed, the determination of the regulating characteristics of the reactor, the speed of response of the shunting reactor in the current and voltage stabilization modes, and also the operation of the reactor under dynamic conditions for different perturbations, are presented. The results obtained are analyzed.

  16. B&W Y-12 donates $2,500 to local Girl Scouts summer camp program | Y-12

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    National Security Complex local Girl Scouts summer camp program Posted: June 27, 2013 - 3:39pm OAK RIDGE, Tenn. - Booth Kammann, (center, left in photo) CEO of the Girl Scout Council of the Southern Appalachians, accepts a donation of $2,500 from Nancy Johnson, B&W Y-12's vice president of Business Services and Performance Assurance, which will help fund the summer program at Camp Tanasi, located near Andersonville on Norris Lake. Joining Kammann and Johnson are (from left in photo)

  17. High Luminosity Options for the JLC.NLC at 500 GeV cms(LCC-0004)

    SciTech Connect (OSTI)

    Raubenheimer, T

    2004-04-22

    The present JLC/NLC parameters are chosen to provide luminosities between 0.5 {approx} 0.75 x 10{sup 34} s{sup -1} cm{sup -2} at a cms energy of 500 GeV; the parameters are listed in Table 1 for both the 500 GeV and 1 TeV cases. In all cases, these luminosities assume extensive margins and emittance dilutions to ensure that they are attainable. In this note, they consider the feasibility of substantially higher luminosities which might be attained by operating with smaller emittance dilutins and higher beam currents. The parameters they describe are listed in Table 2 where these high luminosity sets (ILC-IHa and ILC-IHb) are compared with the base JLC/NLC set (ILC-Ib) and with the high luminosity TESLA parameter set. In the next sections, they will discuss the limitations and assumptions leading to these higher luminosity parameter sets. The details in their discussion will be based on the NLC design described in the Zeroth-order Design Report (ZDR) but the same arguments, with slightly different values, could be applied to the JLC reference design.

  18. An experimental setup for the simultaneous measurement of thermoelectric power of two samples from 77 K to 500 K

    SciTech Connect (OSTI)

    Tripathi, T. S.; Bala, M.; Asokan, K.

    2014-08-01

    We report on an experimental setup for the simultaneous measurement of the thermoelectric power (TEP) of two samples in the temperature range from 77 K to 500 K using optimum electronic instruments. The setup consists of two rectangular copper bars in a bridge arrangement for sample mounting, two surface mount (SM) chip resistors for creating alternate temperature gradient, and a type E thermocouple in differential geometry for gradient temperature (ΔT) measurement across the samples. In addition, a diode arrangement has been made for the alternate heating of SM resistors using only one DC current source. The measurement accuracy of ΔT increases with the differential thermocouple arrangement. For the calibration of the setup, measurements of TEP on a high purity (99.99%) platinum wire and type K thermocouple wires Chromel and Alumel have been performed from 77 K to 500 K with respect to copper lead wires. Additionally, this setup can be utilized to calibrate an unknown sample against a sample of known absolute TEP.

  19. Thermoluminescence (TL) Analysis and Fading Studies of Naturally Occurring Salt Irradiated by 500 mGy Gamma Rays

    SciTech Connect (OSTI)

    Tiwari, Ramesh Chandra; Pau, Kham Suan

    2011-10-20

    The aim of the present study was to investigate the potential of the naturally occurring salt for the dosimetry purposes, using TL. The fine powder samples (20 mg) were irradiated by {gamma}- rays from 500 mGy to 2500 mGy by using Theratron-780C Cobalt-60 source, however, this paper discusses about 500 mGy only. The TL glow curve peak parameters were studied by using Chen's peak shape equation. TL glow curves were compared with fitted curves using glow curve deconvolution (GCD) method by using Kitis expression. The kinetic parameter values (E, b and s) so calculated, are in good agreement with those available in literature. The calculated energy values were also verified by using various heating rate (VHR) method. {chi}{sup 2} test and figure of merit (FOM) calculation was done to accept the goodness of fit between the curves. Fading studies of the sample showed a good fitting between the curves. The analysis suggests that natural salt should be considered for dosimetry purposes.

  20. Distribution Category UC-38 UCRL-52863-Rev.l

    Office of Scientific and Technical Information (OSTI)

    ... 1000 0.6 200 0.79 c a l o r i z e d 100 0.26 600 0.79 500 0.26 S t e e l p l a t e , cough 40 0.94 c a l o r i z e d , oxidized 200 0.18 400 0.97 600 0.19 c a l o r i z e d , ...

  1. Mechanisms of intergranular attack and stress corrosion cracking of Alloy 600 by high-temperature caustic solutions containing impurities: Final report

    SciTech Connect (OSTI)

    Van Rooyen, D.; Bandy, R.

    1987-07-01

    The mechanisms of intergranular attack (IGA) and intergranular stress corrosion cracking (SCC) of Alloy 600 are investigated in high temperature sodium hydroxide environments contaminated with impurities such as carbonate, sulfate, silicate, magnetite, and chromic oxide. Results show that caustic alone can cause both IGA and SCC. The effects of electrochemical potential, stress, time, temperature and the metallurgical state of Alloy 600 on the IGA and SCC are discussed. It appears that both IGA and SCC are manifestations of a general intergranular failure process. In the presence of adverse potential, stress, strain rate and temperature, the slower IGA process is generally replaced by the faster SCC process.

  2. Identification and In-vivo Characterization of a Novel OhrR Transcriptional Regulator in Burkholderia xenovorans LB400

    SciTech Connect (OSTI)

    Nguyen, Tinh T.; Mart-Arbona, Ricardo; Hall, Richard S.; Maity, Tuhin; Valdez, Yolanda E.; Dunbar, John M.; Unkefer, Clifford J.; Unkefer, Pat J.

    2013-05-21

    Transcriptional regulators (TRs) are an important and versatile group of proteins, yet very little progress has been achieved towards the discovery and annotation of their biological functions. We have characterized a previously unknown organic hydroperoxide resistance regulator from Burkholderia xenovoransLB400, Bxe_B2842, which is homologous to E. colis OhrR. Bxe_B2842 regulates the expression of an organic hydroperoxide resistance protein (OsmC). We utilized frontal affinity chromatography coupled with mass spectrometry (FAC-MS) and electrophoretic mobility gel shift assays (EMSA) to identify and characterize the possible effectors of the regulation by Bxe_B2842. Without an effector, Bxe_B2842 binds a DNA operator sequence (DOS) upstream of osmC. FAC-MS results suggest that 2-aminophenol binds to the protein and is potentially an effector molecule. EMSA analysis shows that 2-aminophenol also attenuates the Bxe_B2842s affinity for its DOS. EMSA analysis also shows that organic peroxides attenuate Bxe_B2842/DOS affinity, suggesting that binding of the TR to its DOS is regulated by the two-cysteine mechanism, common to TRs in this family. Bxe_B2842 is the first OhrR TR to have both oxidative and effector-binding mechanisms of regulation. Our paper reveals further mechanistic diversity TR mediated gene regulation and provides insights into methods for function discovery of TRs.

  3. Identification and In-vivo Characterization of a Novel OhrR Transcriptional Regulator in Burkholderia xenovorans LB400

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Nguyen, Tinh T.; Martí-Arbona, Ricardo; Hall, Richard S.; Maity, Tuhin; Valdez, Yolanda E.; Dunbar, John M.; Unkefer, Clifford J.; Unkefer, Pat J.

    2013-05-21

    Transcriptional regulators (TRs) are an important and versatile group of proteins, yet very little progress has been achieved towards the discovery and annotation of their biological functions. We have characterized a previously unknown organic hydroperoxide resistance regulator from Burkholderia xenovoransLB400, Bxe_B2842, which is homologous to E. coli’s OhrR. Bxe_B2842 regulates the expression of an organic hydroperoxide resistance protein (OsmC). We utilized frontal affinity chromatography coupled with mass spectrometry (FAC-MS) and electrophoretic mobility gel shift assays (EMSA) to identify and characterize the possible effectors of the regulation by Bxe_B2842. Without an effector, Bxe_B2842 binds a DNA operator sequence (DOS) upstream ofmore » osmC. FAC-MS results suggest that 2-aminophenol binds to the protein and is potentially an effector molecule. EMSA analysis shows that 2-aminophenol also attenuates the Bxe_B2842’s affinity for its DOS. EMSA analysis also shows that organic peroxides attenuate Bxe_B2842/DOS affinity, suggesting that binding of the TR to its DOS is regulated by the two-cysteine mechanism, common to TRs in this family. Bxe_B2842 is the first OhrR TR to have both oxidative and effector-binding mechanisms of regulation. Our paper reveals further mechanistic diversity TR mediated gene regulation and provides insights into methods for function discovery of TRs.« less

  4. High 400?C operation temperature blue spectrum concentration solar junction in GaInN/GaN

    SciTech Connect (OSTI)

    Zhao, Liang; Detchprohm, Theeradetch; Wetzel, Christian

    2014-12-15

    Transparent wide gap junctions suitable as high temperature, high flux topping cells have been achieved in GaInN/GaN by metal-organic vapor phase epitaxy. In structures of 25 quantum wells (QWs) under AM1.5G illumination, an open circuit voltage of 2.1?V is achieved. Of the photons absorbed in the limited spectral range of <450?nm, 64.2% are converted to electrons collected at the contacts under zero bias. At a fill factor of 45%, they account for a power conversion efficiency of38.6%. Under concentration, the maximum output power density per sun increases from 0.49?mW/cm{sup 2} to 0.51?mW/cm{sup 2} at 40?suns and then falls 0.42?mW/cm{sup 2} at 150?suns. Under external heating, a maximum of 0.59?mW/cm{sup 2} is reached at 250?C. Even at 400?C, the device is fully operational and exceeds room temperature performance. A defect analysis suggests that significantly higher fill factors and extension into longer wavelength ranges are possible with further development. The results prove GaInN/GaN QW solar junctions a viable and rugged topping cell for concentrator photovoltaics with minimal cooling requirements. By capturing the short range spectrum, they reduce the thermal load to any conventional cells stacked behind.

  5. Cultural Resources Review for Closure of the nonradioactive Dangerous Waste Landfill and Solid Waste Landfill in the 600 Area, Hanford Site, Benton County, Washington, HCRC# 2010-600-018R

    SciTech Connect (OSTI)

    Gutzeit, Jennifer L.; Kennedy, Ellen P.; Bjornstad, Bruce N.; Sackschewsky, Michael R.; Sharpe, James J.; DeMaris, Ranae; Venno, M.; Christensen, James R.

    2011-02-02

    The U.S. Department of Energy Richland Operations Office is proposing to close the Nonradioactive Dangerous Waste Landfill (NRDWL) and Solid Waste Landfill (SWL) located in the 600 Area of the Hanford Site. The closure of the NRDWL/SWL entails the construction of an evapotranspiration cover over the landfill. This cover would consist of a 3-foot (1-meter) engineered layer of fine-grained soil, modified with 15 percent by weight pea gravel to form an erosion-resistant topsoil that will sustain native vegetation. The area targeted for silt-loam borrow soil sits in Area C, located in the northern central portion of the Fitzner/Eberhardt Arid Lands Ecology (ALE) Reserve Unit. The pea gravel used for the mixture will be obtained from both off-site commercial sources and an active gravel pit (Pit #6) located just west of the 300 Area of the Hanford Site. Materials for the cover will be transported along Army Loop Road, which runs from Beloit Avenue (near the Rattlesnake Barricade) east-northeast to the NRDWL/SWL, ending at State Route 4. Upgrades to Army Loop Road are necessary to facilitate safe bidirectional hauling traffic. This report documents a cultural resources review of the proposed activity, conducted according to Section 106 of the National Historic Preservation Act of 1966.

  6. Qualification of the Lasentec M600P Particle Size Analyzer and the Red Valve Model 1151 Pressure Sensor

    SciTech Connect (OSTI)

    JR Bontha; NG Colton; EA Daymo; TD Hylton; CK Bayne; TH May

    2000-01-28

    The Lasentec M600 in-line particle size analyzer was installed at Oak Ridge National Laboratory (ORNL) in August 1998 to support retrieval of the Gunite and Associated Tanks (GAAT). Before installation at ORNL, the sensor underwent validation testing at the Pacific Northwest National Laboratory (PNNL) Instrument Validation facility. Mechanically, the instrument worked well during validation testing and met all expectations. Operationally, much was learned about optimum ways to display and interpret the data. Slurry samples taken during the in-line tests at PNNL were shipped to the vendor for analysis with a benchtop Lasentec sensor. These experiments were performed to determine if off-line analyses yield particle size distributions similar to those generated by the in-line sensor. It was determined that the Lasentec sensor measures repeatable chord lengths as long as particles are ''presenter'' to the sensor window the same way. After the initial non-radioactive simulant testing at PNNL, the instrument was shipped for radioactive validation and acceptance testing in the Slurry Monitoring Test System (SMTS) connected to the Tank W-9 of the GAATs at ORNL. For all acceptance tests conducted at ORNL, the variation in the chord length distribution and the total particle count corresponded very well with the slurry density data as determined using an in-line Promass 63M Coriolis meter. Based on the performance results obtained, the Lasentec M600P FBRM is expected to meet the requirements for measuring the particle size distribution during the slurry transfer operations at Hanford and the Oak Ridge GAAT remediation project. The Red Valve pressure sensor was endorsed at the Hanford Site following instrument validation tests at PNNL and is currently in operation in the Tank 241-C-106 pump pit. While this instrument measures pressure within a transfer line, this type of pressure sensor could be configured to measure pressure drop over time. In turn, the status of a slurry

  7. Slide 1

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    - diffusion capacitance C T (V) - transition capacitance V ac - arcing AC voltage - signal frequency -8.00E+03 -7.00E+03 -6.00E+03 -5.00E+03 -4.00E+03 -3.00E+03 -2.00E+03...

  8. Determination of the relative resistance to ignition of selected turbopump materials in high-pressure, high-temperature, oxygen environments, volume 2. Interim report

    SciTech Connect (OSTI)

    Stoltzfus, J.M.; Benz, F.J.

    1986-07-01

    Data from the particle impact tests are presented. Results are provided for the frictional heating tests of pairs of like materials. The materials tested include: Hastelloy X, Inconel 600, Invar 36, Monel K-500, Monel 400, nickel 200, silicon carbide, stainless steel 316, and zironium copper.

  9. Electrochemical and metallurgical aspects of stress corrosion cracking of sensitized Alloy 600 in simulated primary water containing sulfur contamination

    SciTech Connect (OSTI)

    Bandy, R.; Kelly, K.

    1985-01-01

    The stress corrosion cracking (SCC) of sensitized Alloy 600 was investigated in aerated solutions of sodium thiosulfate containing 1.3% boric acid. Results indicate that in the borated thiosulfate solution containing 7 ppM sulfur, 5 ppM lithium as lithium hydroxide is sufficient to inhibit SCC in U-bends. The occurrence of inhibition seems to correlate to the rapid increase of pH and conductivity of the solution as a result of the lithium hydroxide addition. In the slow strain rate tests in the borated solution containing 0.7 ppM lithium as lithium hydroxide, significant SCC is observed at a sulfur level of 30 ppB, i.e., a lithium to sulfur ratio of 23. In a parallel test in 30 ppB sulfur level but without any lithium hydroxide, the SCC is more severe than that in the lithiated environment. In the constant load test on a specimen held initially at a nominal stress near the yield strength of the material, cracks continue to grow until fracture during controlled, progressive dilution of the bulk solution, leading to final lithium concentration of 1.5 ppM and sulfur concentration (as thiosulfate) of 9.6 ppB i.e., a lithium to sulfur ratio of about 156, although lithium hydroxide retards the rate of crack propagation to some extent. The crack growth rate is strongly influenced by the electrochemical potential which is primarily governed by the local crack tip chemistry.

  10. Analysis of the cracking behavior of Alloy 600 RVH penetrations. Part 1: Stress analysis and K computation

    SciTech Connect (OSTI)

    Bhandari, S.; Vagner, J.; Garriga-Majo, D.; Amzallag, C.; Faidy, C.

    1996-12-01

    The study presented here concerns the analysis of crack propagation behavior in the Alloy 600 RVH penetrations used in the French 900 and 1300 MWe PWR series. The damage mechanism identified is clearly the SCC in primary water environment. Consequently the analysis presented here is based on: (1) the stress analysis carried out on the RVH penetrations, (2) the SCC model developed in primary water environment and at the operating temperatures, and (3) the fracture mechanics concepts. The different steps involved in the study are: (1) Evaluation of the stress state for the case of the peripheral configuration of RVH penetrations; the case retained here is that of a conic tube with stress analysis conducted using multi-pass welding. (2) Computation of the influence functions (IF) for a polynomial stress distribution in case of a tube of Ri/t ratio (internal diameter/thickness) corresponding to that of an RVH penetration. (3) Establishment of a propagation law based on study and review of data available in the literature. (4) Conduction of a parametric study of crack propagation using several initial defects. (5) Analysis of crack propagation of defects observed in various reactors and comparison with measured propagation rates. This paper (Part 1) deals with the first two steps namely Stress Analysis and K Computation.

  11. Intergranular attack and stress corrosion cracking propagation behavior of alloy 600 in high-temperature caustic solution

    SciTech Connect (OSTI)

    Kawamura, H.; Hirano, H. . Komae Research Lab.)

    1999-06-01

    The effect of stress intensity factors (K) at the intergranular attack and stress corrosion crack (IGA/SCC) tips on the IGA/SCC propagation behavior of steam generator (SG) tubing was studied under accelerated test conditions. Values of K at the IGA/SCC crack tips were calculated using the statically indeterminate model. Based upon analysis of those factors, the double-cantilever beam (DCB) and SG model boiler tests were carried out to evaluate the effect of stress intensity on IGA/SCC crack propagation. K at the crack tips increased with increasing crack length. For a long crack, K decreased with an increasing number of cracks. However, for a short crack, K decreased slightly with an increasing number of cracks. DCB test results showed the IGA/SCC crack velocity of alloy 600 (UNS N06600) increased gradually with increasing K in the range from 15 MPa[radical]m to [approximately]60 MPa[radical]m. This is the range relevant to IGA/SCC crack tips of typical SG tubes under operating conditions of Pressurized-water reactors. Metallographic examination of tubes removed from the SG model boiler, fouled with 10 ppm sodium hydroxide (NaOH), showed IGA/SCC propagation rates were almost constant in the tested range of K.

  12. Residual stress analysis of alloy 600 U-bends, reverse U-bends, and C-rings: Final report

    SciTech Connect (OSTI)

    Rudd, C.O.

    1994-11-01

    Over the last several years, one of the leading causes of alloy 600 steam generator tubing leaks has been the primary-side-initiated, intergranular stress corrosion cracking (IGSCC) in heavily cold-worked regions of the U-bends or tubesheet expansion transitions. Field and laboratory experiences have demonstrated that high residual stresses contribute significantly to the initiation of primary water stress corrosion cracking (PWSCC). EPRI initiated this project to measure and quantify the magnitude of these residual stresses in steam generator tubes as well as in various laboratory tests specimens. the objectives were: To measure the residual stresses in steam generator tube U-bends; To measure residual stresses in reverse U-bend (RUB) specimens as well as residual stresses and X-ray diffraction peak broadening in C-ring specimens used in laboratory tests; and To determine whether residual stress occurs as a result of exposure to steam generator operating temperature. Using an advanced X-ray instrument, investigators measured residual stresses on both the outside diameter (OD) and inside diameter (ID) surfaces and subsurfaces of steam generator U-bends and on the test surfaces of laboratory RUB and C-ring specimens. They measured these residual stresses in the hoop and axial directions and also calculated equivalent stresses. Results are discussed. 25 refs., 92 figs., 6 tabs.

  13. Beam position monitoring in the 100-MHz to 500-MHz frequency range using the log-ratio technique

    SciTech Connect (OSTI)

    Wells, F.D.; Shafer, R.E.; Gilpatrick, J.D.

    1993-05-01

    A logarithmic-ratio beam position monitor (BPM) circuit has been designed that operates directly from radio frequency- signals in the 100-MHz to 500-MHz frequency range. The circuit uses four logarithmic amplifiers, a pair for each channel. One amplifier per channel receives its signal input directly from a BPM electrode while the second amplifier receives the same signal attenuated by 7-dB. The two outputs of each channel are summed together and the composite video outputs are applied to a differencing amplifier. The net result is the logarithmic-ratio position measurement derived from the two input rf signals. Paralleling the pairs of outputs from the amplifiers provides measurement accuracy that is comparable to other circuit techniques used for position measurement.

  14. Beam position monitoring in the 100-MHz to 500-MHz frequency range using the log-ratio technique

    SciTech Connect (OSTI)

    Wells, F.D.; Shafer, R.E.; Gilpatrick, J.D.

    1993-01-01

    A logarithmic-ratio beam position monitor (BPM) circuit has been designed that operates directly from radio frequency- signals in the 100-MHz to 500-MHz frequency range. The circuit uses four logarithmic amplifiers, a pair for each channel. One amplifier per channel receives its signal input directly from a BPM electrode while the second amplifier receives the same signal attenuated by 7-dB. The two outputs of each channel are summed together and the composite video outputs are applied to a differencing amplifier. The net result is the logarithmic-ratio position measurement derived from the two input rf signals. Paralleling the pairs of outputs from the amplifiers provides measurement accuracy that is comparable to other circuit techniques used for position measurement.

  15. Advanced Photovoltaic Inverter Functionality using 500 kW Power Hardware-in-Loop Complete System Laboratory Testing: Preprint

    SciTech Connect (OSTI)

    Mather, B. A.; Kromer, M. A.; Casey, L.

    2013-01-01

    With the increasing penetration of distribution connected photovoltaic (PV) systems, more and more PV developers and utilities are interested in easing future PV interconnection concerns by mitigating some of the impacts of PV integration using advanced PV inverter controls and functions. This paper describes the testing of a 500 kW PV inverter using Power Hardware-in-Loop (PHIL) testing techniques. The test setup is described and the results from testing the inverter in advanced functionality modes, not commonly used in currently interconnected PV systems, are presented. PV inverter operation under PHIL evaluation that emulated both the DC PV array connection and the AC distribution level grid connection are shown for constant power factor (PF) and constant reactive power (VAr) control modes. The evaluation of these modes was completed under varying degrees of modeled PV variability.

  16. Alternate Multilayer Gratings with Enhanced Diffraction Efficiency in the 500-5000 eV Energy Domain

    SciTech Connect (OSTI)

    Polack, Francois; Lagarde, Bruno; Idir, Mourad; Cloup, Audrey Liard; Jourdain, Erick; Roulliay, Marc; Delmotte, Franck; Gautier, Julien; Ravet-Krill, Marie-Francoise

    2007-01-19

    An alternate multilayer (AML) grating is a 2 dimensional diffraction structure formed on an optical surface, having a 0.5 duty cycle in the in-plane and in the in-depth direction. It can be made by covering a shallow depth laminar grating with a multilayer stack. We show here that their 2D structure confer AML gratings a high angular and energetic selectivity and therefore enhanced diffraction properties, when used in grazing incidence. In the tender X-ray range (500eV - 5000 eV) they behave much like blazed gratings. Over 15% efficiency has been measured on a 1200 lines/mm Mo/Si AML grating in the 1.2 - 1.5 keV energy range. Computer simulations show that selected multilayer materials such as Cr/C should allow diffraction efficiency over 50% at photon energies over 3 keV.

  17. Radio frequency cavity analysis, measurement, and calibration of absolute Dee voltage for K-500 superconducting cyclotron at VECC, Kolkata

    SciTech Connect (OSTI)

    Som, Sumit; Seth, Sudeshna; Mandal, Aditya; Paul, Saikat; Duttagupta, Anjan

    2013-02-15

    Variable Energy Cyclotron Centre has commissioned a K-500 superconducting cyclotron for various types of nuclear physics experiments. The 3-phase radio-frequency system of superconducting cyclotron has been developed in the frequency range 9-27 MHz with amplitude and phase stability of 100 ppm and {+-}0.2{sup 0}, respectively. The analysis of the RF cavity has been carried out using 3D Computer Simulation Technology (CST) Microwave Studio code and various RF parameters and accelerating voltages ('Dee' voltage) are calculated from simulation. During the RF system commissioning, measurement of different RF parameters has been done and absolute Dee voltage has been calibrated using a CdTe X-ray detector along with its accessories and known X-ray source. The present paper discusses about the measured data and the simulation result.

  18. Ru/FeCoB double layered film with high in-plane magnetic anisotropy field of 500 Oe

    SciTech Connect (OSTI)

    Hirata, Ken-ichiro; Hashimoto, Atsuto; Matsuu, Toshimitsu; Nakagawa, Shigeki

    2009-04-01

    FeCoB layers prepared on Ru underlayer possess a high saturation magnetization M{sub s} and a high in-plane magnetic anisotropy filed H{sub k}. Effects of preparation conditions were investigated. Low Ar gas pressure condition and thicker film thickness were effective to attain distortion of FeCo crystallite. As the crystallinity of Ru underlayer became higher, higher H{sub k} was induced. The accumulation of anisotropic stress in the film caused by the oblique incidences of depositing atoms with high energy seems to be one of the important effects to attain high anisotropy field. It was succeeded to prepare the Ru/FeCoB film with high H{sub k} of 500 Oe.

  19. SunShot-funded Advanced Inverter Testing Enables 2,500 Solar Energy Systems to Connect to Hawaiis Electric Grid

    Broader source: Energy.gov [DOE]

    Thanks to a SunShot collaboration at the Energy Departments National Renewable Energy Laboratory (NREL) more than 2,500 Hawaiian Electric customers will connect solar power to the electrical grid...

  20. Advanced, High-Reliability, System-Integrated 500kW PV Inverter Development: Final Subcontract Report, 29 September 2005 - 31 May 2008

    SciTech Connect (OSTI)

    West, R.

    2008-08-01

    Xantrex Technology accomplished subcontract goals of reducing parts cost, weight, and size of its 500-kW inverter by 25% compared to state-of-the-art PV inverters, while extending reliability by 25%.

  1. Surface analysis of Zircaloy-2 implanted with carbon before and after oxidation in air at 500 deg. C

    SciTech Connect (OSTI)

    Peng, D.Q. . E-mail: pdq01@mails.tsinghua.edu.cn; Bai, X.D.; Pan, F.; Sun, H.; Chen, B.S.

    2006-03-15

    Zircaloy-2 specimens were implanted with carbon ions in the fluence range from 1 x 10{sup 16} to 1 x 10{sup 18} ions/cm{sup 2}, using a MEVVA source at an extraction voltage of 40 kV at a maximum temperature of 380 deg. C. The valences and depth profiles of elements in the implanted surface of Zircaloy-2 were analyzed by X-ray photoelectron spectroscopy and Auger electron spectroscopy, respectively. Scanning electron microscopy was used to examine the micro-morphology of samples. The color of the oxidized samples was checked with an optical scanner. Glancing-angle X-ray diffraction at 0.3{sup o} incident angles was employed to examine the phase transformations of implanted samples before and after oxidation in the air at 500 deg. C for 2 h. Before oxidation, at fluences less than 5 x 10{sup 16} ions/cm{sup 2}, hexagonal zirconia (H-ZrO{sub 0.35}) was present. At a fluence of 1 x 10{sup 17} ions/cm{sup 2}, rhombohedral zirconia (R-Zr{sub 3}O) appeared. When the fluence reached 1 x 10{sup 18} ions/cm{sup 2}, cubic zirconium carbide was produced. There are many pits, both deep and shallow, in the sample surfaces, both prior to oxidation and after oxidation. Oxidation in the air at 500 deg. C gave rise to black surfaces on all samples. The X-ray diffraction results showed that monoclinic and tetragonal zirconia were present in the surface of as-received sample. For implanted samples, monoclinic and tetragonal zirconia are still present, while cubic zirconium carbide is produced at all fluences. The presence of ZrC is attributed to the high-temperature, long-time (2 h) exposure.

  2. EIS-0005-FS: Bonneville Power Administration Proposed FY 1979 Program, Facility Location on Supplement, Southwest Oregon Area Service, Buckley-Summer Lake 500 kV Line, Supplemental

    Broader source: Energy.gov [DOE]

    This Bonneville Power Administration document assesses the environmental impacts of constructing transmission facilities, which will coordinate with the Midpoint-Malin 500-kV line to be constructed by the Pacific Power and Light (PP&L) Company. The proposed action includes the construction of the 1.56-mile Buckley-Summer Lake 500-kV transmission line; the proposed Buckley Substation near Maupin, Oregon; and the proposed Summer Lake Substation near Silver Lake, Oregon.

  3. An observational study suggesting clinical benefit for adjuvant postoperative chemoradiation in a population of over 500 cases after gastric resection with D2 nodal dissection for adenocarcinoma of the stomach

    SciTech Connect (OSTI)

    Kim, Sung; Lim, Do Hoon; Lee, Jeeyun; Kang, Won Ki . E-mail: wkkang@smc.samsung.co.kr; MacDonald, John S.; Park, Chan Hyung; Park, Se Hoon; Lee, Se-Hoon; Kim, Kihyun; Park, Joon Oh; Kim, Won Seog; Jung, Chul Won; Park, Young Suk; Im, Young-Hyuck; Sohn, Tae Sung; Noh, Jae Hyung; Heo, Jin Seok; Kim, Yong Il; Park, Chul Keun; Park, Keunchil

    2005-12-01

    Purpose: The role of adjuvant chemoradiotherapy (CRT) in D2-resected gastric-cancer patients has not been defined yet. We investigated the effect of postoperative chemoradiotherapy on the relapse rate and survival rate of patients with D2-resected gastric cancer. Methods and Materials: From August 1995 to April 2001, 544 patients received postoperative CRT after curative D2 resection. During the same period of time, 446 patients received surgery without further adjuvant treatment. The adjuvant CRT consisted of 400 mg/m{sup 2} of fluorouracil plus 20 mg/m{sup 2} of leucovorin for 5 days, followed by 4,500 cGy of radiotherapy for 5 weeks, with fluorouracil and leucovorin on the first 4 and the last 3 days of radiotherapy. Two 5-day cycles of fluorouracil and leucovorin were given 4 weeks after the completion of radiotherapy. Results: The median duration of overall survival was significantly longer in the CRT group than in the comparison group (95.3 months vs. 62.6 months), which corresponds to a hazard ratio for death of 0.80 (p = 0.0200) or a reduction of 20% in the risk of death in the CRT group. The 5-year survival rates were consistently longer in the CRT group at Stages II, IIIA, IIIB, and IV than those in the comparison group. The CRT was associated with increases in the median duration of relapse-free survival (75.6 months vs. 52.7 months; hazard ratio for relapse, 0.80, p = 0.0160). Conclusion: Our results highly suggest that the postoperative chemoradiotherapy in D2-resected gastric-cancer patients can prolong survival and decrease recurrence.

  4. Fracture toughness, tensile and stress corrosion cracking properties of Alloy 600, Alloy 690 and their welds in water

    SciTech Connect (OSTI)

    Brown, C.M.; Mills, W.J.

    1996-10-01

    The fracture toughness and tensile properties of Alloy 600, Alloy 690 and their welds, EN82H and EN52, were characterized in 54 and 338 C water with an elevated hydrogen content. Results were compared with air data to evaluate the effect of low and high temperature water on mechanical properties. In addition, the stress corrosion cracking (SCC) behavior of EN82H and EN52 welds was evaluated in 360 C water with high hydrogen. Elastic-plastic J{sub c} fracture toughness testing revealed that the fracture resistance of all test materials was exceptionally high in 54 and 338 C air and 338 C water, demonstrating that fracture properties were essentially unaffected by the high temperature water environment. In 54 C water, however, J{sub c} values for EN82H and EN52 welds were reduced by an order of magnitude, and Alloy 690 showed a five-fold decrease in J{sub c}. Tensile properties for all test materials were essentially unaffected by the water environment, except for the total elongation for EN82H welds which was significantly reduced in 54 C water. At a strain rate of 5 x 10{sup 6} sec{sup {minus}1} in low temperature water, there appears to be sufficient time for environmental interactions to restrict ductility in EN82H welds. Constant-load testing of precracked weld specimens in 360 C water resulted in extensive intergranular SCC in EN82H welds loaded to K{sub I} levels between 35 and 55 MPa {radical}m, whereas no SCC occurred in EN52 welds under comparable test conditions.

  5. Inhibitory effect of boric acid on intergranular attack and stress corrosion cracking of Alloy 600 in high temperature water

    SciTech Connect (OSTI)

    Kawamura, H.; Hirano, H.; Koike, M.; Suda, M.

    1995-09-01

    The inhibitory effect of boric acid on the Intergranular Attack and Stress Corrosion Cracking (IGA/SCC) propagation behavior of steam generator (SG) tubing was studied under accelerated test conditions. Based on the analysis results of stress intensity factors at IGA/SCC crack tips, the notched C-ring tests were carried out to evaluate the effect of stress intensity and boric acid on the IGA/SCC crack propagation. The A.C. impedance measurement and Auger electron spectroscopy (AES) were also conducted to clarify the inhibitory effect of boric acid. Notched C-ring test results indicated that IGA/SCC crack velocity of alloy 600 increased gradually with increasing stress intensity factor in the range 4 to about 26 MPa{center_dot}m{sup 1/2}, which might be loaded on the IGA/SCC crack tips of actual SG tubes under PWR secondary conditions. Adding boric acid slightly retarded the crack velocity in both all volatile treatment (AVT) water and caustic solutions. IGA/SCC crack velocities were lower in nearly neutral solutions than in alkali or acidic solutions. Furthermore, A.C. impedance studies showed that the polarization resistances of oxide films formed in boric acid solutions were higher than those of films formed in acidic and alkali solutions. AES analysis revealed that boron content in the oxide films formed in acidic solution containing boric acid was lowest. Good agreement was obtained between the IGA/SCC inhibitory effect of boric acid and the formation of the stable oxide films containing boron.

  6. High-Resolution Characterization of Intergranular Attack and Stress Corrosion Cracking of Alloy 600 in High-Temperature Primary Water

    SciTech Connect (OSTI)

    Thomas, Larry E.; Bruemmer, Stephen M.

    2000-06-01

    Intergranular (IG) attack regions and stress-corrosion cracks in alloy 600 U-bend samples tested in 330C, pressurized-water-reactor water have been characterized by analytical transmission electron microscopy (ATEM). Observations of cross-sectional samples revealed short oxidized zones preceding crack tips and narrow (10-nm wide), deeply penetrated, oxidized zones along grain boundaries exposed along open cracks. High-resolution TEM imaging and fine-probe analysis were used to determine the local chemistries and structures in these corrosion-affected zones. Matrix areas surrounding the crack tips appeared highly strained, whereas the IG penetrations generally did not. The predominant oxide structure found along crack walls and just ahead of crack tips was NiO with metal-atom ratios similar to the alloy. The attacked grain boundaries off open cracks contained similar fine-grained NiO-structure oxide together with local areas of Cr-rich oxide and Ni-rich metal. In contrast, Cr-rich oxide identified as Cr2O3 predominated at the leading edges of the IG attack. Stereoscopic imaging of these tip structures revealed nm-scale porosity and tunnels within the oxide and pores along the grain-boundary plane ahead of the oxide. The general interpretation of these results is that IG attack and cracking follows local dissolution or oxidation and the formation of pores at grain boundaries. This degradation occurs at the nanometer scale and therefore requires high-resolution ATEM methods to reveal detailed characteristics. Experimental support for several possible IG degradation mechanisms is considered.

  7. Measurement of Activation Reaction Rate Distributions in a Lead Assembly Bombarded with 500-MeV Protons

    SciTech Connect (OSTI)

    Takada, Hiroshi; Meigo, Shin-ichro; Sasa, Toshinobu; Tsujimoto, Kazufumi; Yasuda, Hideshi

    2000-05-15

    Reaction rate distributions of various activation detectors such as the {sup nat}Ni(n,x){sup 58}Co, {sup 197}Au(n,2n){sup 196}Au, and {sup 197}Au(n,4n){sup 194}Au reactions were measured to study the production and the transport of spallation neutrons in a lead assembly bombarded with protons of 500 MeV. The measured data were analyzed with the nucleon-meson transport code NMTC/JAERI combined with the MCNP4A code using the nuclide production cross sections based on the JENDL Dosimetry File and those calculated with the ALICE-F code. It was found that the NMTC/JAERI-MCNP4A calculations agreed well with the experiments for the low-energy-threshold reaction of {sup nat}Ni(n,x){sup 58}Co. With the increase of threshold energy, however, the calculation underestimated the experiments, especially above 20 MeV. The reason for the disagreement can be attributed to the underestimation of the neutron yield in the tens of mega-electron-volt regions by the NMTC/JAERI code.

  8. A Preclinical Study of the Safety and Efficacy of Occlusin Trade-Mark-Sign 500 Artificial Embolization Device in Sheep

    SciTech Connect (OSTI)

    Owen, Richard J.; Nation, Patrick N.; Polakowski, Robert; Biliske, Jennifer A.; Tiege, Paul B.

    2012-06-15

    Introduction: This study evaluated the safety, effectiveness, and biodegradation of a new embolic agent, Occlusin Trade-Mark-Sign 503 Artificial Embolization Device (OCL 503). The agent consists of biodegradable poly-lactic-co-glycolic acid microspheres (150-212 {mu}m) coated with type I bovine collagen and was compared with Embosphere{sup Registered-Sign} Microspheres (300-500 {mu}m) in this controlled study of uterine artery embolization (UAE) in sheep. Methods: Unilateral UAE was performed in 32 adult ewes randomly assigned. Vessels were embolized to effective stasis. The cohort was divided into four groups, which were sacrificed at 1, 3, 6, and 12 months. Results: Both agents were 100% effective in achieving stasis. At 6 months, all OCL 503-treated arteries were occluded, the microspheres degraded with time, and at 12 months all four animals examined demonstrated recanalization. OCL 503 was found in the untreated uterine artery in one animal with no other evidence of non target embolization. In the Embosphere-treated group, all vessels remained occluded and microspheres were detected in the contralateral uterine artery in 6 of 15 examined vessels and in 10 vaginal, 2 ovarian, and 1 vesical artery. No procedural-related complications were seen in either group. Conclusions: OCL 503 is as effective an embolic agent as Embosphere{sup Registered-Sign} Microspheres when embolizing ovine uterine arteries and resorbs with time, allowing recanalization of the treated arteries. No device-related issues or adverse events were observed.

  9. 500-MHz x-ray counting with a Si-APD and a fast-pulse processing system

    SciTech Connect (OSTI)

    Kishimoto, Shunji; Taniguchi, Takashi; Tanaka, Manobu

    2010-06-23

    We introduce a counting system of up to 500 MHz for synchrotron x-ray high-rate measurements. A silicon avalanche photodiode detector was used in the counting system. The fast-pulse circuit of the amplifier was designed with hybrid ICs to prepare an ASIC system for a large-scale pixel array detector in near future. The fast amplifier consists of two cascading emitter-followers using 10-GHz band transistors. A count-rate of 3.25x10{sup 8} s{sup -1} was then achieved using the system for 8-keV x-rays. However, a baseline shift by adopting AC-coupling in the amplifier disturbed us to observe the maximum count of 4.49x10{sup 8} s{sup -1}, determined by electron-bunch filling into a ring accelerator. We also report that an amplifier with a baseline restorer was tested in order to keep the baseline level to be 0 V even at high input rates.

  10. Successful continuous injection of coal into gasification and PFBC system operating pressures exceeding 500 PSI - DOE funded program results

    SciTech Connect (OSTI)

    2005-07-01

    President Bush's energy program is focussed towards commercializing power production technologies that offer improvements in efficiency and reductions in emissions while utilizing the nation's most abundant energy reserve - coal. Gasification offers such benefits. To bring this technology to full commercial acceptance, the operational issue of feeding solid fuel into the pressure environment needs to be addressed. The DOE, through the National Energy Technology Laboratory, has funded research to develop the unique Stamet 'Posimetric Solids Pump' to feed coal into current gasification operating pressures. The project comprised design and testing to feed coal into 300 PSI and a second Phase for feeding into 500 PSI. The 300 PSI target was achieved in December 2003. In January 2005, the Posimetric feeder achieved continuous injection of coal into 560 PSI, exceeding the Phase 2 target. This paper presents a review and evaluation of the design, design optimizations and test results of the successful feeder. It also presents analysis of economic benefits to pump use and results from semi-commercial testing at gasifier operating test facilities, which should have commenced by the date of the Conference. 16 figs., 6 tabs.

  11. Acceleration of 500 keV Negative Ion Beams By Tuning Vacuum Insulation Distance On JT-60 Negative Ion Source

    SciTech Connect (OSTI)

    Kojima, A.; Hanada, M.; Tanaka, Y.; Taniguchi, M.; Kashiwagi, M.; Inoue, T.; Umeda, N.; Watanabe, K.; Tobari, H.; Kobayashi, S.; Yamano, Y.; Grisham, L. R.

    2011-09-26

    Acceleration of a 500 keV beam up to 2.8 A has been achieved on a JT-60U negative ion source with a three-stage accelerator by overcoming low voltage holding which is one of the critical issues for realization of the JT-60SA ion source. In order to improve the voltage holding, preliminary voltage holding tests with small-size grids with uniform and locally intense electric fields were carried out, and suggested that the voltage holding was degraded by both the size and local electric field effects. Therefore, the local electric field was reduced by tuning gap lengths between the large size grids and grid support structures of the accelerator. Moreover, a beam radiation shield which limited extension of the minimum gap length was also optimized so as to reduce the local electric field while maintaining the shielding effect. These modifications were based on the experiment results, and significantly increased the voltage holding from <150 kV/stage for the original configuration to 200 kV/stage. These techniques for improvement of voltage holding should also be applicable to other large ion sources accelerators such as those for ITER.

  12. Absorption of a single 500 fs laser pulse at the surface of fused silica: Energy balance and ablation efficiency

    SciTech Connect (OSTI)

    Varkentina, N.; Sanner, N.; Lebugle, M.; Sentis, M.; Utéza, O.

    2013-11-07

    Ablation of fused silica by a single femtosecond laser pulse of 500 fs pulse duration is investigated from the perspective of efficiency of incident photons to remove matter. We measure the reflected and transmitted fractions of the incident pulse energy as a function of fluence, allowing us to recover the evolution of absorption at the material surface. At the ablation threshold fluence, 25% of incident energy is absorbed. At high fluences, this ratio saturates around 70% due to the appearance of a self-triggered plasma mirror (or shielding) effect. By using the energy balance retrieved experimentally and measurements of the ablated volume, we show that the amount of absorbed energy is far above the bonding energy of fused silica at rest and also above the energy barrier to ablate the material under non-equilibrium thermodynamic conditions. Our results emphasize the crucial role of transient plasma properties during the laser pulse and suggest that the major part of the absorbed energy has been used to heat the plasma formed at the surface of the material. A fluence range yielding an efficient and high quality ablation is also defined, which makes the results relevant for femtosecond micromachining processes.

  13. Seasonal Patterns of Melatonin, Cortisol, and Progesterone Secretion in Female Lambs Raised Beneath a 500-kV Transmission Line.

    SciTech Connect (OSTI)

    Lee, Jack M.

    1992-06-01

    Although several kinds of biological effects of electric and magnetic fields have been reported from laboratory studies, few have been independently replicated. When this study was being planned, the suppression of nighttime melatonin in rodents was thought to represent one of the strongest known effects of these fields. The effect had been replicated by a single laboratory for 60-Hz electric fields, and by multiple laboratories for d-c magnetic fields. The primary objective of this study was to determine whether the effect of electric and magnetic fields on melatonin would also occur in sheep exposed to a high voltage transmission line. The specific hypothesis tested by this experiment was as follows: The electrical environment produced by a 60-Hz, 500-kV transmission line causes a depression in nocturnal melatonin in chronically exposed female lambs. This may mimic effects of pinealectomy or constant long-day photoperiods, thus delaying the onset of reproductive cycles. Results of the study do not provide evidence to support the hypothesis. Melatonin concentrations in the sheep exposed to the transmission line showed the normal pattern of low daytime and high nighttime serum levels. As compared to the control group, there were no statistically significant group differences in the mean amplitude, phase, or duration of the nighttime melatonin elevation.

  14. Stress-corrosion cracking of Alloys 600 and 690 and weld metals No. 82 and No. 182 in high-temperature water. Interim report. [BWR

    SciTech Connect (OSTI)

    Page, R.A.

    1982-09-01

    The relative susceptibilities of Alloys 600 and 690 base metals and I-82 and 182 weld metals to intergranular stress corrosion cracking (IGSCC) in pure water at 288/sup 0/C were evaluated. A combination of creviced and non-creviced slow-strain-rate, smooth sustained-load, and precracked fracture mechanics tests were employed in the evaluation. Susceptibility was determined as a function of dissolved oxygen content, degree of sensitization, and crevice condition. The results indicated that Alloy 600, and I-182 and I-82 weld metals were susceptible to various degrees of IGSCC in oxygen containing pure water when creviced, and immune to IGSCC when uncreviced. Alloy 690 was immune to IGSCC under all conditions examined. No correlation was found between the location of IGSCC and the location of maximum grain boundary corrosion in a boiling 25% nitric acid test.

  15. SPES-2, AP600 intergral system test S01007 2 inch CL to core make-up tank pressure balance line break

    SciTech Connect (OSTI)

    Bacchiani, M.; Medich, C.; Rigamonti, M.

    1995-09-01

    The SPES-2 is a full height, full pressure experimental test facility reproducing the Westinghouse AP600 reactor with a scaling factor of 1/395. The experimental plant, designed and operated by SIET in Piacenza, consists of a full simulation of the AP600 primary core cooling system including all the passive and active safety systems. In 1992, Westinghouse, in cooperation with ENEL (Ente Nazionale per l` Energia Elettrica), ENEA (Enter per le numove Technlogie, l` Energia e l` Ambient), Siet (Societa Informazioni Esperienze Termoidraulich) and ANSALDO developed an experimental program to test the integrated behaviour of the AP600 passive safety systems. The SPES-2 test matrix, concluded in November 1994, has examined the AP600 passive safety system response for a range of small break LOCAs at different locations on the primary system and on the passive system lines; single steam generator tube ruptures with passive and active safety systems and a main steam line break transient to demonstrate the boration capability of passive safety systems for rapid cooldown. Each of the tests has provided detailed experimental results for verification of the capability of the analysis methods to predict the integrated passive safety system behaviour. Cold and hot shakedown tests have been performed on the facility to check the characteristics of the plant before starting the experimental campaign. The paper first presents a description of the SPES-2 test facility then the main results of S01007 test {open_quotes}2{close_quotes} Cold Leg (CL) to Core Make-up Tank (CMT) pressure balance line break{close_quotes} are reported and compared with predictions performed using RELAP5/mod3/80 obtained by ANSALDO through agreement with U.S.N.R.C. (U.S. Nuclear Regulatory Commission). The SPES-2 nodalization and all the calculations here presented were performed by ANSALDO and sponsored by ENEL as a part of pre-test predictions for SPES-2.

  16. Midtemperature solar systems test facility predictions for thermal performance based on test data: solar kinetics T-600 solar collector with FEK 244 reflector surface

    SciTech Connect (OSTI)

    Harrison, T.D.

    1981-04-01

    Sandia National Laboratories, Albuquerque (SNLA), is currently conducting a program to predict the performance and measure the characteristics of commercially available solar collectors that have the potential for use in industrial process heat and enhanced oil recovery applications. The thermal performance predictions for the Solar Kinetics T-600 solar line-focusing parabolic trough collector are presented for three output temperatures at five cities in the US. (WHK)

  17. Influence of stress intensity and loading mode on intergranular stress corrosion cracking of Alloy 600 in primary waters of pressurized water reactors

    SciTech Connect (OSTI)

    Rebak, R.B.; Szklarska-Smialowska, Z. . Fontana Corrosion Center)

    1994-05-01

    The steam generator in a pressurized water reactor (PWR) of a nuclear power plant consists mainly of a shell made of carbon (C) steel and tubes made of alloy 600 (UNS N06600). However, alloy 600 suffers environmentally induced cracking with exposure to high-temperature primary water. The susceptibility of alloy 600 to integranular stress corrosion cracking (IGSCC) was investigated as a function of the level of applied stresses and mode of loading. Constant load tests were conducted with specimens prepared from thin wall tubes, and constant deformation tests were conducted using specimens prepared from plates. With tubes exposed to primary water at 330 C, the crack propagation rate (CPR) was found to increase from 1 [times] 10[sup [minus]11] m/s at a stress intensity (K[sub i]) of 10 MPa[radical]m to 1 [times] 10[sup [minus]9] at K[sub i] = 60 MPa[radical]m. CPR obtained using compact specimens prepared from plates were 1 order of magnitude lower than values measured in tubes at the same temperature and in the same solution at each stress intensity. The corollary was that values of crack propagation and threshold stress intensities obtained using compact specimens could not be extrapolated to the behavior of thin wall tubes.

  18. The role of Hydrogen and Creep in Intergranular Stress Corrosion Cracking of Alloy 600 and Alloy 690 in PWR Primary Water Environments ? a Review

    SciTech Connect (OSTI)

    Rebak, R B; Hua, F H

    2004-07-12

    Intergranular attack (IGA) and intergranular stress corrosion cracking (IGSCC) of Alloy 600 in PWR steam generator environment has been extensively studied for over 30 years without rendering a clear understanding of the essential mechanisms. The lack of understanding of the IGSCC mechanism is due to a complex interaction of numerous variables such as microstructure, thermomechanical processing, strain rate, water chemistry and electrochemical potential. Hydrogen plays an important role in all these variables. The complexity, however, significantly hinders a clearer and more fundamental understanding of the mechanism of hydrogen in enhancing intergranular cracking via whatever mechanism. In this work, an attempt is made to review the role of hydrogen based on the current understanding of grain boundary structure and chemistry and intergranular fracture of nickel alloys, effect of hydrogen on electrochemical behavior of Alloy 600 and Alloy 690 (e.g. the passive film stability, polarization behavior and open-circuit potential) and effect of hydrogen on PWSCC behavior of Alloy 600 and Alloy 690. Mechanistic studies on the PWSCC are briefly reviewed. It is concluded that further studies on the role of hydrogen on intergranular cracking in both inert and primary side environments are needed. These studies should focus on the correlation of the results obtained at different laboratories by different methods on materials with different metallurgical and chemical parameters.

  19. Identification of non-ordinary mesons from the dispersive connection between their poles and their Regge trajectories: The f{sub 0}(500) resonance

    SciTech Connect (OSTI)

    Pelaez, J. R.; Londergan, J. T.; Nebreda, J.; Szczepaniak, Adam P.

    2014-02-01

    We show how the Regge trajectory of a resonance can be obtained from its pole in a scattering process and analytic constraints in the complex angular momentum plane. The method is suited for resonances that dominate an elastic scattering amplitude. In particular, from the {rho}(770) resonance pole in {pi}{pi} scattering, we obtain its linear Regge trajectory, characteristic of ordinary quark–antiquark states. In contrast, the f{sub 0}(500) pole—the sigma meson—which dominates scalar isoscalar {pi}{pi} scattering, yields a nonlinear trajectory with a much smaller slope at the f{sub 0}(500) mass. Conversely, imposing a linear Regge trajectory for the f{sub 0}(500), with a slope of typical size, yields an elastic amplitude at odds with the data. This provides strong support for the non-ordinary nature of the sigma meson.

  20. Tracking in full Monte Carlo detector simulations of 500 GeV e{sup +}e{sup {minus}} collisions

    SciTech Connect (OSTI)

    Ronan, M.T.

    2000-03-01

    In full Monte Carlo simulation models of future Linear Collider detectors, charged tracks are reconstructed from 3D space points in central tracking detectors. The track reconstruction software is being developed for detailed physics studies that take realistic detector resolution and background modeling into account. At this stage of the analysis, reference tracking efficiency and resolutions for ideal detector conditions are presented. High performance detectors are being designed to carry out precision studies of e{sup +}e{sup {minus}} annihilation events in the energy range of 500 GeV to 1.5 TeV. Physics processes under study include Higgs mass and branching ratio measurements, measurement of possible manifestations of Supersymmetry (SUSY), precision Electro-Weak (EW) studies and searches for new phenomena beyond their current expectations. The relatively-low background machine environment at future Linear Colliders will allow precise measurements if proper consideration is given to the effects of the backgrounds on these studies. In current North American design studies, full Monte Carlo detector simulation and analysis is being used to allow detector optimization taking into account realistic models of machine backgrounds. In this paper the design of tracking software that is being developed for full detector reconstruction is discussed. In this study, charged tracks are found from simulated space point hits allowing for the straight-forward addition of background hits and for the accounting of missing information. The status of the software development effort is quantified by some reference performance measures, which will be modified by future work to include background effects.

  1. Word Pro - Untitled1

    Gasoline and Diesel Fuel Update (EIA)

    Coal Production, 1949-2011 Total By Rank By Mining Method By Location 200 U.S. Energy Information Administration / Annual Energy Review 2011 Anthracite Lignite¹ Subbituminous Coal¹ ¹ Subbituminous coal and lignite are included in bituminous coal prior to 1969. Source: Table 7.2. 1950 1960 1970 1980 1990 2000 2010 0 300 600 900 1,200 1,500 Million Short Tons Bituminous Coal¹ 1950 1960 1970 1980 1990 2000 2010 0 200 400 600 800 Million Short Tons 1950 1960 1970 1980 1990 2000 2010 0 300 600

  2. Role of carbides in stress corrosion cracking resistance of alloy 600 and controlled-purity Ni-16% Cr-9% Fe in primary water at 360 C

    SciTech Connect (OSTI)

    Was, G.S.; Lian, K.

    1998-09-01

    Intergranular stress corrosion cracking (IGSCC) of two commercial alloy 600 (UNS N06600) conditions (heat-treated at low temperature [600LT] and at high temperature [600HT]) and two controlled-purity Ni-16% Cr-9% Fe alloys (carbon-doped mill-annealed [CDMA] and carbon-doped thermally treated [CTRR]) were investigated using constant extension rate tensile (CERT) tests in primary water (0.001 M lithium hydroxide [LiOH] + 0.01 M boric acid [H{sub 3}BO{sub 3}]) with 1 bar (100 kPa) hydrogen overpressure at 360 C and 320 C. Heat treatments produced two types of microstructures in the commercial and controlled-purity alloys: one dominated by grain-boundary carbides (600HT and CDTT) and one dominated by intragranular carbides (600LT and CDMA). CERT tests were conducted over a range of strain rates and at two temperatures with interruptions at specific strains to determine the crack depth distributions. Results showed IGSCC was the dominant failure mode in all samples. For the commercial alloy and controlled-purity alloys, the microstructure with grain-boundary carbides showed delayed crack initiation and shallower crack depths than did the intragranular carbide microstructure under all experimental conditions. Data indicated a grain-boundary carbide microstructure is more resistant to IGSCC than an intragranular carbide microstructure. Observations supported the film rupture/slip dissolution mechanism and enhanced localized plasticity. The advantage of these results over previous studies was that the different carbide distributions were obtained in the same commercial alloy using different heat treatments and, in the other case, in nearly identical controlled-purity alloys. Observations of the effects of carbide distribution on IGSCC could be attributed more confidently to the carbide distribution alone rather than other potentially significant differences in microstructure or composition. Crack growth rates (CGR) increased with increasing strain rate according to a power

  3. Expansion of Michigan EOR Operations Using Advanced Amine Technology at a 600 MW Project Wolverine Carbon Capture and Storage Project

    SciTech Connect (OSTI)

    H Hoffman; Y kishinevsky; S. Wu; R. Pardini; E. Tripp; D. Barnes

    2010-06-16

    Wolverine Power Supply Cooperative Inc, a member owned cooperative utility based in Cadillac Michigan, proposes to demonstrate the capture, beneficial utilization and storage of CO{sub 2} in the expansion of existing Enhanced Oil Recovery operations. This project is being proposed in response to the US Department of Energy Solicitation DE-FOA-0000015 Section III D, 'Large Scale Industrial CCS projects from Industrial Sources' Technology Area 1. The project will remove 1,000 metric tons per day of CO{sub 2} from the Wolverine Clean Energy Venture 600 MW CFB power plant owned and operated by WPC. CO{sub 2} from the flue gas will be captured using Hitachi's CO{sub 2} capture system and advanced amine technology. The capture system with the advanced amine-based solvent supplied by Hitachi is expected to significantly reduce the cost and energy requirements of CO{sub 2} capture compared to current technologies. The captured CO{sub 2} will be compressed and transported for Enhanced Oil Recovery and CO{sub 2} storage purposes. Enhanced Oil Recovery is a proven concept, widely used to recover otherwise inaccessible petroleum reserves. While post-combustion CO{sub 2} capture technologies have been tested at the pilot scale on coal power plant flue gas, they have not yet been demonstrated at a commercial scale and integrated with EOR and storage operations. Amine-based CO{sub 2} capture is the leading technology expected to be available commercially within this decade to enable CCS for utility and industrial facilities firing coal and waste fuels such as petroleum coke. However, traditional CO{sub 2} capture process utilizing commercial amine solvents is very energy intensive for regeneration and is also susceptible to solvent degradation by oxygen as well as SOx and NO{sub 2} in the flue gas, resulting in large operating costs. The large volume of combustion flue gas with its low CO{sub 2} concentration requires large equipment sizes, which together with the highly

  4. Puerto Rico and U.S. Virgin Islands Wind Resource Map at 50 meters

    Wind Powering America (EERE)

    % % % % % % % % % % % % % % % % % % % % % 19-JUN-2007 1.1.1 U.S. Department of Energy National Renewable Energy Laboratory Puerto Rico and U.S. Virgin Islands - 50 m Wind Power Mayaguez 20 0 20 40 60 80 100 Kilometers 20 0 20 40 60 Miles Ponce San Juan Charlotte Amalie Cruz Bay PUERTO RICO VIRGIN ISLANDS Wind Power Class 1 2 3 4 5 Resource Potential Poor Marginal Fair Good Excellent Wind Power Density at 50 m W/m 0 - 200 200 - 300 300 - 400 400 - 500 500 - 600 2 Wind Speed at 50 m m/s 0.0 - 5.9

  5. EIS-0032: 500 kV International Transmission Line NSP-TR-1, Forbes, Minnesota to Manitoba, Canada, Northern States Power Company

    Broader source: Energy.gov [DOE]

    The Economic Regulatory Administration developed this EIS to evaluate the environmental impacts of a 500-kilovolt transmission line proposed by the Northern States Power Company to provide a transmission facility for the exchange of electrical energy between Canada and the United States.

  6. Increasing the reliability of the shutdown of 500 - 750-kV overhead lines equipped with shunt reactors in an unsuccessful three-phase automatic repeated closure cycle

    SciTech Connect (OSTI)

    Kuz'micheva, K. I.; Merzlyakov, A. S.; Fokin, G. G.

    2013-05-15

    The reasons for circuit-breaker failures during repeated disconnection of 500 - 750 kV overhead lines with shunt reactors in a cycle of unsuccessful three-phase automatic reconnection (TARC) are analyzed. Recommendations are made for increasing the operating reliability of power transmission lines with shunt reactors when there is unsuccessful reconnection.

  7. Baseline System Costs for 50.0 MW Enhanced Geothermal System--A Function of: Working Fluid, Technology, and Location, Location, Location

    Broader source: Energy.gov [DOE]

    Project objectives: Develop a baseline cost model of a 50.0 MW Enhanced Geothermal System, including all aspects of the project, from finding the resource through to operation, for a particularly challenging scenario: the deep, radioactively decaying granitic rock of the Pioneer Valley in Western Massachusetts.

  8. Development of a 400 Level 3C Clamped Downhole Seismic Receiver Array for 3D Borehole Seismic Imaging of Gas Reservoirs

    SciTech Connect (OSTI)

    Bjorn N. P. Paulsson

    2006-09-30

    Borehole seismology is the highest resolution geophysical imaging technique available today to the oil and gas industry for characterization and monitoring of oil and gas reservoirs. However, the industry's ability to perform high resolution 3D imaging of deep and complex gas reservoirs using borehole seismology has been hampered by the lack of acquisition technology necessary to record large volumes of high frequency, high signal-to-noise-ratio borehole seismic data. This project took aim at this shortcoming by developing a 400 level 3C clamped downhole seismic receiver array, and accompanying software, for borehole seismic 3D imaging. This large borehole seismic array has removed the technical acquisition barrier for recording the data volumes necessary to do high resolution 3D VSP and 3D cross-well seismic imaging. Massive 3D VSP{reg_sign} and long range Cross-Well Seismology (CWS) are two of the borehole seismic techniques that promise to take the gas industry to the next level in their quest for higher resolution images of deep and complex oil and gas reservoirs. Today only a fraction of the oil or gas in place is produced when reservoirs are considered depleted. This is primarily due to our lack of understanding of detailed compartmentalization of oil and gas reservoirs. In this project, we developed a 400 level 3C borehole seismic receiver array that allows for economic use of 3D borehole seismic imaging for reservoir characterization and monitoring. This new array has significantly increased the efficiency of recording large data volumes at sufficiently dense spatial sampling to resolve reservoir complexities. The receiver pods have been fabricated and tested to withstand high temperature (200 C/400 F) and high pressure (25,000 psi), so that they can operate in wells up to 7,620 meters (25,000 feet) deep. The receiver array is deployed on standard production or drill tubing. In combination with 3C surface seismic or 3C borehole seismic sources, the 400

  9. Studies and optimization of Pohang Light Source-II superconducting radio frequency system at stable top-up operation with beam current of 400 mA

    SciTech Connect (OSTI)

    Joo, Youngdo Yu, Inha; Park, Insoo; Chun, Myunghwan; Lee, Byung-Joon; Hwang, Ilmoon; Ha, Taekyun; Shin, Seunghwan; Sohn, Younguk

    2014-12-21

    After three years of upgrading work, the Pohang Light Source-II (PLS-II) is now successfully operating. The final quantitative goal of PLS-II is a top-up user-service operation with beam current of 400 mA to be completed by the end of 2014. During the beam store test up to 400 mA in the storage ring (SR), it was observed that the vacuum pressure around the radio frequency (RF) window of the superconducting cavity rapidly increases over the interlock level limiting the availability of the maximum beam current storing. Although available beam current is enhanced by setting a higher RF accelerating voltage, it is better to keep the RF accelerating voltage as low as possible in the long time top-up operation. We investigated the cause of the window vacuum pressure increment by studying the changes in the electric field distribution at the superconducting cavity and waveguide according to the beam current. In our simulation, an equivalent physical modeling was developed using a finite-difference time-domain code. The simulation revealed that the electric field amplitude at the RF window is exponentially increased as the beam current increases, thus this high electric field amplitude causes a RF breakdown at the RF window, which comes with the rapid increase of window vacuum pressure. The RF accelerating voltage of PLS-II RF system was set to 4.95 MV, which was estimated using the maximum available beam current that works as a function of RF voltage, and the top-up operation test with the beam current of 400 mA was successfully carried out.

  10. Remaining Sites Verification Package for the 600-243 Petroleum-Contaminated Soil Bioremediation Pad, Waste Site Reclassification Form 2007-033

    SciTech Connect (OSTI)

    J. M. Capron

    2008-11-07

    The 600-243 waste site consisted of a bioremediation pad for petroleum-contaminated soils resulting from the 1100 Area Underground Storage Tank (UST) upgrades in 1994. In accordance with this evaluation, the verification sampling results support a reclassification of this site to Interim Closed Out. The results of verification sampling show that residual contaminant concentrations do not preclude any future uses and allow for unrestricted use of shallow zone soils. The results also demonstrate that residual contaminant concentrations are protective of groundwater and the Columbia River.

  11. f{sub 0}(600) and f{sub 0}(980) pole positions from a dispersive {pi}{pi} scattering data analysis

    SciTech Connect (OSTI)

    Ruiz e Elvira, J.; Martin, R. Garcia; Pelaez, J. R.; Kaminski, R.

    2011-05-23

    We show how the new precise data on kaon decays together with forward dispersion relations, sum rules and once- and twice-subtracted Roy equations allow for a precise analysis of {pi}{pi} scattering. The once subtracted Roy equations provide a more stringent consistency check for the parametrizations of the S0-wave data in the region from 450 to 1100 MeV that allows us to present a preliminary determination of the f{sub 0}(600) and f{sub 0}(980) poles from the constrained dispersive data analysis.

  12. Analytical TEM Comparisons of Stress-Corrosion-Crack Microstructure in Alloy 600 under Steam-Generator Service and Laboratory Test Conditions

    SciTech Connect (OSTI)

    Thomas, Larry E.; Bruemmer, Stephen M.; Scott, Peter M.

    2002-05-31

    High-resolution analytical transmission electron microscopy (ATEM) been used to characterize stress-corrosion cracks in Alloy 600 steam-generator tubing from tests with caustic and acid-sulfate solutions. The aim of this work was to identify the microstructural and microchemical signatures of intergranular attack and cracking produced under well-controlled test conditions in order to determine the local environments promoting degradation in service. The examinations are part of an experimental program devoted to a study of IGA/IGSCC in steam generator tube alloys supported by the Framatome Owners Group via its Steam Generator Technical Committee.

  13. Un~ted States Env~ronmental Monltor~ng EPA.600 '4-88, 021 Envtronmental Protect~on Systems Laboratory DOE/OP/00539/060

    Office of Legacy Management (LM)

    Env~ronmental Monltor~ng EPA.600 '4-88, 021 Envtronmental Protect~on Systems Laboratory DOE/OP/00539/060 Agency P 0. Box 93478 June 1988 Las Vegas NV 89193-5478 Research and Development Off-Site Environmental Monitoring Report Radiation Monitoring Around United States 1 ' 7 L 8 f Nuclear Test Areas This page intentionally left blank EPA-60014-88-021 DOE/DPI0053?-060 May 1988 OFF-SITE ENVIRONMENTAL MONITORING REPORT R a d i a t i o n M o n i t o r i n g Around U n i t e d States Nuclear Test

  14. Field Testing of LIDAR-Assisted Feedforward Control Algorithms for Improved Speed Control and Fatigue Load Reduction on a 600-kW Wind Turbine: Preprint

    SciTech Connect (OSTI)

    Kumar, Avishek A.; Bossanyi, Ervin A.; Scholbrock, Andrew K.; Fleming, Paul; Boquet, Mathieu; Krishnamurthy, Raghu

    2015-12-14

    A severe challenge in controlling wind turbines is ensuring controller performance in the presence of a stochastic and unknown wind field, relying on the response of the turbine to generate control actions. Recent technologies such as LIDAR, allow sensing of the wind field before it reaches the rotor. In this work a field-testing campaign to test LIDAR Assisted Control (LAC) has been undertaken on a 600-kW turbine using a fixed, five-beam LIDAR system. The campaign compared the performance of a baseline controller to four LACs with progressively lower levels of feedback using 35 hours of collected data.

  15. INFLUENCE OF CARBON AND DPA RATE ON NEUTRON-INDUCED SWELLING OF Fe-15Cr-16Ni-0.25Ti IN FFTF AT ~400 DEGREES C

    SciTech Connect (OSTI)

    Okita, Taira; Sekimura, Naoto; Garner, Francis A.; Wolfer, W. G.

    2002-12-31

    The purpose of this effort is to determine the influence of dpa rate and composition on the void swelling of simple austenitic Fe-Cr-Ni alloys. Contrary to the swelling behavior of fcc Fe-15Cr-16Ni and Fe-15Cr-16Ni-0.25Ti alloys irradiated in the same FFTF-MOTA experiment, Fe-15Cr-16Ni-0.25Ti-0.04C does not exhibit a dependence of swelling on dpa rate at approximately 400 degrees C. The transient regime of swelling is prolonged by carbon addition, however.

  16. {open_quotes}In-situ{close_quotes} stress-relieving of Ni/Cu alloy 400 tubed high pressure feedwater heaters

    SciTech Connect (OSTI)

    Rahoi, D.W.

    1995-12-01

    One of the known failure methods of Ni/Cu Alloy 400 is stress-corrosion cracking. When it can be determined with physical evidence that this is occurring, it may be possible to arrest or, at least slow down the failure methods by performing an {open_quotes}in situ{close_quotes} stress relief using plant steam. This paper does not recommend how to do it, but does reveal there is some hope the relief-anneal slows down the failure rate and increases the heater life, by reducing residual stress.

  17. Low-field magnetoresistance up to 400 K in double perovskite Sr{sub 2}FeMoO{sub 6} synthesized by a citrate route

    SciTech Connect (OSTI)

    Harnagea, L.; Jurca, B.; Berthet, P.

    2014-03-15

    A wet-chemistry technique, namely the citrate route, has been used to prepare high-quality polycrystalline samples of double perovskite Sr{sub 2}FeMoO{sub 6}. We report on the evolution of magnetic and magnetoresistive properties of the synthesized samples as a function of three parameters (i) the pH of the starting solution, (ii) the decomposition temperature of the citrate precursors and (iii) the sintering conditions. The low-field magnetoresistance (LFMR) value of our best samples is as high as 5% at room temperature for an applied magnetic field of 1 kOe. Additionally, the distinguishing feature of these samples is the persistence of LFMR, with a reasonably large value, up to 400 K which is a crucial parameter for any practical application. Our study indicates that the enhancement of LFMR observed is due to a good compromise between the grain size distribution and their magnetic polarization. -- Graphical abstract: The microstructure (left panel) and corresponding low-field magnetoresistance of one of the Sr{sub 2}FeMoO{sub 6} samples synthesized in the course of this work. Highlights: Samples of Sr{sub 2}FeMoO{sub 6} are prepared using a citrate route under varying conditions. Magnetoresistive properties are improved and optimized. Low-field magnetoresitence values as large as 5% at 300 K/1 kOe are reported. Persistence of low-field magnetoresistance up to 400 K.

  18. Intermetallic phase formation and breakdown of Mo diffusion barriers in Ni-Mo-Cu and Ni-Mo-Monel 400 diffusion triads

    SciTech Connect (OSTI)

    Shueh, Y.

    1988-01-01

    The purpose of this research was to study the kinetics of compound formation and the interdiffusion behavior of a sacrificial type diffusion barrier in a model system. Ni-Mo diffusion couples were annealed in an inert atmosphere at 950-1050{degree}C for 5-300 hours. Ni-Mo-Cu and Ni-Mo-Monel 400 diffusion triads with varied thicknesses of Mo layers sandwiched by Ni and C or Monel 400 disks were annealed under the same conditions. Parabolic growth of the intermetallic phase, {beta}, was observed at 1000{degree}C and 1050{degree}C in the semi-infinite Ni-Mo diffusion couple an din the Ni-Mo-Cu diffusion triad when a finite thickness of the Mo layer remained. The {beta} phase exhibited more or less planar morphology except in the case of some extremely rugged interfaces which were associated with grain boundaries adjacent to these interfaces. Dissociation and recession of the compound layer in Ni-Mo-Cu diffusion triads initiated when the Mo layer was nearly consumed. The product phases of the dissociation reaction are consistent with those predicted from the Ni-Mo-Cu ternary phase diagram. Numerical methods based on a finite difference technique, and an analytical solution based on diffusion controlled parabolic growth and quasi-steady-state approximation in the {beta} phase region were used to analyze the results.

  19. Effectiveness of 700{degrees}C thermal treatment on primary water stress corrosion sensitivity of Alloy 600 steam generator tubes: Laboratory tests and in field experience

    SciTech Connect (OSTI)

    Cattant, F.; Keroulas, F. de; Garriga-Majo, D.; Todeschini, P.; Van Duysen, J.C.

    1992-12-31

    In France, the steam generators of some 900 MWe reactors, and of all the 1 300 MWe reactors in service are equipped with heat treated Alloy 600 tubes. The purpose of the heat treatment, performed at 700{degrees}C, is to relieve the residual stresses. Generally, it also increases the SCC resistance of the alloy. A laboratory study has been carried out in order to gain a better understanding of the metallurgical factors influencing the PWSCC resistance of Alloy 600 after heat treatment. It has been shown that there are two kinds of tubes for which the heat treatment does not produce a microstructure having a potentially high resistance to SCC: tubes with a high carbon content (over 0.032%) or tubes mill-annealed at high temperatures and heavily cold-worked by the straightening. The analysis of the behaviour of french steam generators reveals that the heat treatment generally had the expected beneficial effect. However, the early cracking in service of some treated tubes led EDF (national power company) to proceed with removals. The majority of the cracked pulled-out tubes exhibit microstructures having a potentially high PWSCC sensibility in laboratory tests. It has been shown that these microstructures can be correlated to a high carbon content.

  20. Catalytic steam gasification reactivity of HyperCoals produced from different rank of coals at 600-775{degree}C

    SciTech Connect (OSTI)

    Atul Sharma; Ikuo Saito; Toshimasa Takanohashi

    2008-11-15

    HyperCoal is a clean coal with ash content <0.05 wt %. HyperCoals were prepared from a brown coal, a sub-bituminous coal, and a bituminous raw coal by solvent extraction method. Catalytic steam gasification of these HyperCoals was carried out with K{sub 2}CO{sub 3} at 775, 700, 650, and 600 {degree}C, and their rates were compared. HyperCoals produced from low-rank coals were more reactive than those produced from the high-rank coals. XRD measurements were carried out to understand the difference in gasification reactivity of HyperCoals. Arrhenius plot of ln (k) vs 1/T in the temperature range 600-825{degree}C was a curve rather than a straight line. The point of change was observed at 700{degree}C for HyperCoals from low-rank coals and at 775{degree}C for HyperCoals from high-rank coals. Using HyperCoal produced from low-rank coals as feedstock, steam gasification of coal may be possible at temperatures less than 650{degree}C. 22 refs., 6 figs., 2 tabs.

  1. Generation of 500 MeV-1 GeV energy electrons from laser wakefield acceleration via ionization induced injection using CO{sub 2} mixed in He

    SciTech Connect (OSTI)

    Mo, M. Z.; Ali, A.; Fedosejevs, R.; Fourmaux, S.; Lassonde, P.; Kieffer, J. C.

    2013-04-01

    Laser wakefield acceleration of 500 MeV to 1 GeV electron bunches has been demonstrated using ionization injection in mixtures of 4% to 10% of CO{sub 2} in He. 80 TW laser pulses were propagated through 5 mm gas jet targets at electron densities of 0.4-1.5 Multiplication-Sign 10{sup 19}cm{sup -3}. Ionization injection led to lower density thresholds, a higher total electron charge, and an increased probability of producing electrons above 500 MeV in energy compared to self-injection in He gas alone. Electrons with GeV energies were also observed on a few shots and indicative of an additional energy enhancement mechanism.

  2. Evaluated Mean Values and Covariances for the Prompt Fission Neutron Spectrum of 239Pu induced by neutrons of 500 keV

    SciTech Connect (OSTI)

    Neudecker, Denise

    2014-07-10

    This document provides the numerical values of the evaluated prompt fission neutron spectrum for 239Pu induced by neutrons of 500 keV as well as relative uncertainties and correlations. This document also contains a short description how these data were obtained and shows plots comparing the evaluated results to experimental information as well as the corresponding ENDF/B-VII.1 evaluation.

  3. Commissioning of the 112 MHz SRF Gun and 500 MHz bunching cavities for the CeC PoP Linac

    SciTech Connect (OSTI)

    Belomestnykh, S.; Ben-Zvi, I.; Brutus, J. C.; Litvinenko, V.; McIntosh, P.; Moss, A.; Narayan, G.; Orfin, P.; Pinayev, I.; Rao, T.; Skaritka, J.; Smith, K.; Than, R.; Tuozzolo, J.; Wang, E.; Wheelhouse, A.; Wu, Q.; Xiao, B.; Xin, T.; Xu, W.; Zaltsman, A.

    2015-05-03

    The Coherent electron Cooling Proof-of-Principle (CeC PoP) experiment at BNL includes a short electron linac. During Phase 1, a 112 MHz superconducting RF photo-emission gun and two 500 MHz normal conducting bunching cavities were installed and are under commissioning. The paper describes the Phase1 linac layout and presents commissioning results for the cavities and associated RF, cryogenic and other sub-systems

  4. Level 1 Accident Investigation Report of August 17, 2004, Fatal Aircraft Accident on the Grand Coulee-Bell No.6, 500 kV Line

    Broader source: Energy.gov [DOE]

    On August 17, 2004, at approximately 0940, a Bonneville Power Administration (BPA) pilot was killed in the crash of a Bell 206BIII helicopter while stringing "sock line" to enable the subsequent stringing of new conductors and static wire on the Grand Coulee-Bell #6 500-kV line between tower 84/2 and BPA’s Bell Substation in Mead, Washington. (See Appendix 7, Site Map.)

  5. Automatic system for regulating the frequency and power of the 500 MW coal-dust power generating units at the Reftinskaya GRES

    SciTech Connect (OSTI)

    Bilenko, V. A.; Gal'perina, A. I.; Mikushevich, E. E.; Nikol'skii, D. Yu.; Zhugrin, A. G.; Bebenin, P. A.; Syrchin, M. V.

    2009-03-15

    The monitoring and control systems at the 500 MW coal-dust power generating units No. 7, 8, and 9 at the Reftinskaya GRES have been modernized using information-regulator systems. Layouts for instrumental construction of these systems and expanded algorithmic schemes for the automatic frequency and power control system and for the boiler supply and fuelling are discussed. Results from tests and normal operation of the automatic frequency and power control system are presented.

  6. US ESC TN Site Consumption

    U.S. Energy Information Administration (EIA) Indexed Site

    ESC TN Site Consumption million Btu $0 $500 $1,000 $1,500 $2,000 $2,500 US ESC TN Expenditures dollars ALL ENERGY average per household (excl. transportation) 0 4,000 8,000 12,000 16,000 US ESC TN Site Consumption kilowatthours $0 $400 $800 $1,200 $1,600 US ESC TN Expenditures dollars ELECTRICITY ONLY average per household * Tennessee households consume an average of 79 million Btu per year, about 12% less than the U.S. average. * Average electricity consumption for Tennessee households is 33%

  7. Word Pro - Untitled1

    U.S. Energy Information Administration (EIA) Indexed Site

    0 Natural Gas Plant Liquids Production Total, 1949-2011 By Product, 2011 By Selected Product, 1949-2011 138 U.S. Energy Information Administration / Annual Energy Review 2011 Source: Table 5.10. 1950 1960 1970 1980 1990 2000 2010 0 500 1,000 1,500 2,000 2,500 Thousand Barrels per Day 909 618 295 208 152 Ethane Propane Pentanes Isobutane Normal 0 200 400 600 800 1,000 Thousand Barrels per Day Plus Butane Isobutane Normal Butane Propane 1950 1955 1960 1965 1970 1975 1980 1985 1990 1995 2000 2005

  8. Repeated compressive stress increase with 400 [degree]C thermal cycling in tantalum thin films due to increases in the oxygen content

    SciTech Connect (OSTI)

    Cabral, C. Jr.; Clevenger, L.A.; Schad, R.G. )

    1994-07-01

    Stresses which build up in thin films such as tantalum, during thermal processing, can cause major reliability problems in electronic and x-ray optics applications. We demonstrate that 50--200 nm thick sputtered [beta]-Ta thin films undergo repeated compressive stress increases when thermally cycled to 400 [degree]C (at a rate of 10 [degree]C/min) and back in a purified He ambient because of small amounts of oxygen gettered by the tantalum. The oxygen contamination results from the poor quality of the atmospheric seal on the quartz annealing chamber. As-deposited Ta thin films have a compressive stress ranging from [minus]1 to [minus]4 GPa. The compressive stress buildup was monitored [ital in] [ital situ] and was shown to increase [minus]0.5 GPa on average after each thermal cycle for a final value from [minus]6 to [minus]7 GPa after seven cycles. After being cycled thermally seven times any perturbation of the film such as a four-point probe resistivity measurement can cause the film to instantaneously crack in a serpentine pattern, relieving the large compressive stress. Auger electron spectroscopy depth profiling analysis was used to determine that the as-deposited film contained 1 at. % oxygen which increased to 8%--12% after seven thermal cycles with an approximate doubling in resistivity. The [minus]0.5 GPa average compressive stress increase in Ta thin films when cycled to 400 [degree]C is attributed to a 1.3% increase in oxygen concentration leading to a Ta unit cell expansion of 0.6%.

  9. Effects of pH and stress intensity on crack growth rate in Alloy 600 in lithiated + borated water at high temperatures

    SciTech Connect (OSTI)

    Rebak, R.B.; Szklarska-Smialowska, Z.; McIlree, A.R.

    1992-12-31

    Primary water stress corrosion cracking studies were performed on Alloy 600. Constant load tests were conducted at 330 and 350{degrees}C in solutions containing dissolved hydrogen, boric acid (0 < B < 1200 ppm) and lithium hydroxide (0 < Li < 10 ppm). In the PWR working conditions range, that is, 6.9 < pH < 7.4 (or 0.5 ppm < Li < 3.5), there is little effect of the solution pH on the intergranular crack growth rate (IGSCC). However, there is a strong influence of the stress intensity on the IGSCC. K{sub ISCC} {approx} 5-10 MPa{radical}m. Dissolution plays an important role in the IGSCC process.

  10. Intergranular stress-corrosion cracking of Ni-Cr-Fe Alloy 600 tubes in PWR primary water - review and assessment for model development. Final report

    SciTech Connect (OSTI)

    Garud, Y.S.; Gerber, T.L.

    1983-05-01

    The service performance of Ni-Cr-Fe Alloy 600 tubes with respect to primary-side intergranular stress-corrosion cracking (IGSCC) and related experimental observations are reviewed, assessed, and summarized. The qualitative trends suggested by these observations and the role of primary variables of IGSCC are discussed from the point of view of mechanistic considerations. The need for a quantitative model to predict the IGSCC is established. The review and assessment indicate that, in addition to the water chemistry and metallurgical variables, explicit consideration of stress (and attendant deformation, i.e., strain-rate) is essential for any evaluation of the IGSCC to be complete. A promising approach of quantitative model development is presented with the above background. The analytical-experimental work needed for the model development is suggested, and implementation of the model and potential benefits to utilities is briefly discussed.

  11. Strain rate and temperature effects on the stress corrosion cracking of Inconel 600 steam generator tubing in the primary water conditions

    SciTech Connect (OSTI)

    Kim, U.C.; van Rooyen, D.

    1985-01-01

    A single heat of Inconel Alloy 600 was examined in this work, using slow strain rate tests (SSRT) in simulated primary water at temperatures of 325/sup 0/-345/sup 0/-365/sup 0/C. The best measure of stress corrosion cracking (SCC) was percent SCC present on the fracture surface. Strain rate did not seem to affect crack growth rate significantly, but there is some question about the accuracy of calculating these values in the absence of a direct indication of when a crack initiates. Demarcation was determined between domains of temperature/strain rate where SCC either did, or did not, occur. Slower extension rates were needed to produce SCC as the temperature was lowered. 10 figs.

  12. Effects of Cr and Nb contents on the susceptibility of Alloy 600 type Ni-base alloys to stress-corrosion cracking in a simulated BWR environment

    SciTech Connect (OSTI)

    Akashi, Masatsune

    1995-09-01

    In order to discuss the effects of chromium and niobium contents on the susceptibility of Alloy 600 type nickel-base alloys to stress-corrosion cracking in the BWR primary coolant environment, a series of creviced bent-beam (CBB) tests were conducted in a high-temperature, high-purity water environment. Chromium, niobium, and titanium as alloying elements improved the resistivity to stress-corrosion cracking, whereas carbon enhanced the susceptibility to it. Alloy-chemistry-based correlations have been defined to predict the relative resistances of alloys to stress-corrosion cracking. A strong correlation was found, for several heats of alloys, between grain-boundary chromium depletion and the susceptibility to stress-corrosion cracking.

  13. Role of residual stresses in stress corrosion cracking in alloy 600 tubes. Part 1. Determination of throughwall residual stresses and their modification by transient heat treatment

    SciTech Connect (OSTI)

    Bandy, R.; Zemanian, T.

    1985-01-01

    The effect of transient heat treatment on throughwall residual stress distribution of cold worked Alloy 600 tubes has been investigated, using electrochemical machining coupled with Sachs analyses for residual stress calculations. Heating for 60 to 150 seconds at 775 to 850 C is used. Specimens are made from one highly cold worked and one lightly cold worked tube. In both cases significant reduction of the magnitude of the stress, and modification of the stress distribution are achieved as a result of the heat treatment. The percentage reduction of the magnitude of the stress caused by the same heat treatment is generally greater in the lightly cold worked tube than in the highly cold worked one. The implications of the stress relieving heat treatments to mitigating stress corrosion cracking in a specific case are discussed. 14 references, 17 figures, 1 table.

  14. A Microstructural and Kinetic Investigation of the KCl-Induced Corrosion of an FeCrAl Alloy at 600 °C

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Israelsson, Niklas; Unocic, Kinga A.; Hellström, K.; Jonsson, T.; Norell, M.; Svensson, J. -E.; Johansson, L. -G.

    2015-03-18

    In this paper, the corrosion behaviour of a FeCrAl alloy was investigated at 600 °C in O2 + H2O with solid KCl applied. A kinetics and microstructural investigation showed that KCl accelerates corrosion and that potassium chromate formation depletes the protective scale in Cr, thus triggering the formation of a fast-growing iron-rich scale. Iron oxide was found to grow both inward and outward, on either side of the initial oxide. A chromia layer is formed with time underneath the iron oxide. Finally, it was found that although the alloy does not form a continuous pure alumina scale at the investigatedmore » temperature, aluminium is, however, always enriched at the oxide/alloy interface.« less

  15. The study of stress application and corrosion cracking on Ni-16 Cr-9 Fe (Alloy 600) C-ring samples by polychromatic X-ray microdiffraction

    SciTech Connect (OSTI)

    Chao, Jing; Fuller, Marina L Suominen; McIntyre, N Stewart; Carcea, Anatolie G; Newman, Roger C; Kunz, Martin; Tamura, Nobumichi

    2012-03-27

    Microscopic strains associated with stress corrosion cracks have been investigated in stressed C-rings of Ni-16 Cr-9 Fe (Alloy 600) boiler tubing. Polychromatic X-ray microdiffraction was used to measure deviatoric strain tensors and the distribution of dislocations near cracks that had been propagated in electrochemically accelerated corrosion tests. An associated investigation of the C-ring-induced strains prior to corrosion showed significant tensile strain in the stress axis direction by the torsional closure of the alloy tube section in the C-ring test. Significant grain lattice rotation and pronounced plastic strain at some grain boundaries were noted. Stress-corrosion-cracking-generated intergranular cracks were produced in two Alloy 600 specimens after 6 h and 18 h tests. The diffraction patterns and resultant strain tensors were mapped around the cracked area to a 1 μm spatial resolution. The strain tensor transverse to the crack growth direction showed tensile strain at the intergranular region just ahead of the crack tip for both specimens. Both cracks were found to follow grain boundary pathways that had the lowest angle of misorientation. Dislocation distributions within each grain were qualitatively obtained from the shapes of the diffraction spots and the effect of 'hard' and 'soft' grains on the crack pathway was explored for both 6 h and 18 h specimens. The Schmid factor of one of the grains adjacent to the crack at the 6 h and 18 h initiation sites was found to be the lowest, compared to Schmid factors calculated for surface grains away from the initiation site, and also along the crack path into the bulk.

  16. Effect of water on mechanical properties and stress corrosion behavior of alloy 600, alloy 690, EN82H welds, and EN52 welds

    SciTech Connect (OSTI)

    Brown, C.M.; Mills, W.J.

    1999-02-01

    The fracture toughness and tensile properties of alloy 600 (UNS N06600), alloy 690 (UNS N06690), and their welds (EN82H [UNS N06082] and EN52 [UNS N06052]) were characterized in 54 C and 338 C water with an elevated hydrogen content. Results were compared with air data to evaluate the effect of low- and high-temperature water on the mechanical properties. In addition, the stress corrosion cracking (SCC) behavior of EN82H and EN52 welds was evaluated in 360 C water. Elastic-plastic (J{sub IC}) fracture toughness testing revealed that the fracture resistance of all test materials was exceptionally high in 54 C and 338 C air and 338 C water, demonstrating that fracture properties essentially were unaffected by the high-temperature water environment. In 54 C water, however, J{sub IC} values for EN82H and EN52 welds were reduced by an order of magnitude, and alloy 690 showed a fivefold decrease in J{sub IC}. Scanning electron fractography revealed that the degraded fracture properties were associated with a fracture mechanism transition from ductile dimple rupture to intergranular cracking. The latter was associated with hydrogen-induced cracking mechanism. The fracture toughness for alloy 600 remained high in 54 C water, and microvoid coalescence was the operative mechanism in low-temperature air and water. Tensile properties for all test materials essentially were unaffected by the water environment, except for the total elongation for EN82H welds, which was reduced significantly in 54 C water. Constant-load testing of precracked weld specimens in 360 C water resulted in extensive intergranular SCC in EN82H welds, whereas no SCC occurred in EN52 welds under comparable test conditions.

  17. Crack growth rates and metallographic examinations of Alloy 600 and Alloy 82/182 from field components and laboratory materials tested in PWR environments.

    SciTech Connect (OSTI)

    Alexandreanu, B.; Chopra, O. K.; Shack, W. J.

    2008-05-05

    In light water reactors, components made of nickel-base alloys are susceptible to environmentally assisted cracking. This report summarizes the crack growth rate results and related metallography for field and laboratory-procured Alloy 600 and its weld alloys tested in pressurized water reactor (PWR) environments. The report also presents crack growth rate (CGR) results for a shielded-metal-arc weld of Alloy 182 in a simulated PWR environment as a function of temperature between 290 C and 350 C. These data were used to determine the activation energy for crack growth in Alloy 182 welds. The tests were performed by measuring the changes in the stress corrosion CGR as the temperatures were varied during the test. The difference in electrochemical potential between the specimen and the Ni/NiO line was maintained constant at each temperature by adjusting the hydrogen overpressure on the water supply tank. The CGR data as a function of temperature yielded activation energies of 252 kJ/mol for a double-J weld and 189 kJ/mol for a deep-groove weld. These values are in good agreement with the data reported in the literature. The data reported here and those in the literature suggest that the average activation energy for Alloy 182 welds is on the order of 220-230 kJ/mol, higher than the 130 kJ/mol commonly used for Alloy 600. The consequences of using a larger value of activation energy for SCC CGR data analysis are discussed.

  18. High-Pressure Raman Spectroscopy and X-ray Diffraction Studies of a Terpolymer of Tetrafluoroethylene-Hexafluoropropylene-Vinylidene Fluoride: THV 500

    SciTech Connect (OSTI)

    Emmons, E.D.; Velisavljevic, N.; Schoonover, J.R.; Dattelbaum, D.M.

    2008-04-02

    High-pressure Raman spectroscopy and X-ray diffraction of THV 500, a terpolymer of tetrafluoroethylene-hexafluoropropylene-vinylidene fluoride, were performed using diamond anvil cells (DAC). Changes in the interatomic spacing as well as shifts of several of the vibrational bands as a function of pressure were measured up to {approx}10 GPa. The changes in interatomic spacing and shifts of the vibrational bands are compared to those of polytetrafluoroethylene, showing the effects of copolymerization and reduced crystallinity. The high-pressure behavior of polymers is a relatively unexplored field but is becoming increasingly important due to applications where polymers experience extreme conditions.

  19. Study of Polarized Sea Quark Distributions in Polarized Proton-Proton Collisions at sq root(s) = 500 GeV with PHENIX

    SciTech Connect (OSTI)

    Mibe, Tsutomu

    2009-08-04

    The PHENIX spin program studies the flavor structure of the polarized sea quark distributions in polarized proton-proton collisions. Starting from 2009 run, the quark and antiquark polarization, sorted by flavor, will be investigated with the parity-violating single-spin asymmetry of W-boson production at the collision energy of sq root(s) = 500 GeV. High momentum muons from W-boson decay are detected in the PHENIX muon arms. The muon trigger is being upgraded to allow one to select high momentum muons.

  20. Measurement of residual nucleus cross sections and recoil energies in p + Fe collisions at 300, 500, 750, 1000 and 1500 MeV

    SciTech Connect (OSTI)

    Villagrasa, C.; Boudard, A.; Ducret, J.-E.; Fernandez, B.; Leray, S.; Volant, C.; Wlazlo, W.; Audouin, L.; Ferran, L.; Rejmund, F.

    2005-05-24

    The production of residual nuclei in p + Fe collisions has been measured at GSI on the FRS facility by means of the reverse kinematic techniques at 300, 500, 750, 1000 and 1500 MeV/A. The cross-sections larger than 0.01 mb of all isotopes with Z larger than 8 have been obtained. Velocity distributions were also measured. Comparisons to models describing spallation reactions and some empirical formulae often used in astrophysics are presented. These data are directly used to calculate impurity production and DPAs in a thin window as foreseen in spallation sources or accelerator-driven systems.

  1. Development of NS-TACSR with extremely suppressed aeolian noise and its application to 500 kV overhead transmission lines

    SciTech Connect (OSTI)

    Tsujimoto, K.; Furukawa, S. (Kansai Electric Power Co., Inc., Osaka (Japan)); Shimojima, K.; Yamamoto, K. (Hitachi Cable, Ltd., Hitachi (JP))

    1991-10-01

    Recently in Japan, with the unprecedented advance of residential area development in the suburbs of large cities, it has become quite difficult to secure the routes of EHV transmission lines from nuclear power plants in remote places to the suburbs of large cities, urging resolution of environmental problems related to transmission lines. In Japan, aerodynamic sound produced by conductors and insulators frequently caused noise problems. Having an opportunity of constructing a 500 kV transmission line through a residential are, we made a research to resolve this noise problem. This paper describes the characteristics of aeolian noise and preventive measures against it.

  2. HEDL FACILITIES CATALOG 400 AREA

    SciTech Connect (OSTI)

    MAYANCSIK BA

    1987-03-01

    The purpose of this project is to provide a sodium-cooled fast flux test reactor designed specifically for irradiation testing of fuels and materials and for long-term testing and evaluation of plant components and systems for the Liquid Metal Reactor (LMR) Program. The FFTF includes the reactor, heat removal equipment and structures, containment, core component handling and examination, instrumentation and control, and utilities and other essential services. The complex array of buildings and equipment are arranged around the Reactor Containment Building.

  3. 500 MW X-Band RF System of a 0.25 GeV Electron LINAC for Advanced Compton Scattering Source Application

    SciTech Connect (OSTI)

    Chu, Tak Sum; Anderson, Scott; Barty, Christopher; Gibson, David; Hartemann, Fred; Marsh, Roark; Siders, Craig; Adolphsen, Chris; Jongewaard, Erik; Raubenheimer, Tor; Tantawi, Sami; Vlieks, Arnold; Wang, Juwen; /SLAC

    2012-07-03

    A Mono-Energetic Gamma-Ray (MEGa-Ray) Compton scattering light source is being developed at LLNL in collaboration with the SLAC National Accelerator Laboratory. The electron beam for the Compton scattering interaction will be generated by a X-band RF gun and a X-band LINAC at the frequency of 11.424 GHz. High power RF in excess of 500 MW is needed to accelerate the electrons to energy of 250 MeV or greater for the interaction. Two high power klystron amplifiers, each capable of generating 50 MW, 1.5 msec pulses, will be the main high power RF sources for the system. These klystrons will be powered by state of the art solid-state high voltage modulators. A RF pulse compressor, similar to the SLED II pulse compressor, will compress the klystron output pulse with a power gain factor of five. For compactness consideration, we are looking at a folded waveguide setup. This will give us 500 MW at output of the compressor. The compressed pulse will then be distributed to the RF gun and to six traveling wave accelerator sections. Phase and amplitude control are located at the RF gun input and additional control points along the LINAC to allow for parameter control during operation. This high power RF system is being designed and constructed. In this paper, we will present the design, layout, and status of this RF system.

  4. 500 MW X-BAND RF SYSTEM OF A 0.25 GEV ELECTRON LINAC FOR ADVANCED COMPTON SCATTERING SOURCE APPLICATION

    SciTech Connect (OSTI)

    Chu, T S; Anderson, S G; Gibson, D J; Hartemann, F V; Marsh, R A; Siders, C; Barty, C P; Adolphsen, C; Jongewaard, E; Tantawi, S; Vlieks, A; Wang, J W; Raubenheimer, T

    2010-05-12

    A Mono-Energetic Gamma-Ray (MEGa-Ray) Compton scattering light source is being developed at LLNL in collaboration with SLAC National Accelerator Laboratory. The electron beam for the Compton scattering interaction will be generated by a X-band RF gun and a X-band LINAC at the frequency of 11.424 GHz. High power RF in excess of 500 MW is needed to accelerate the electrons to energy of 250 MeV or greater for the interaction. Two high power klystron amplifiers, each capable of generating 50 MW, 1.5 msec pulses, will be the main high power RF sources for the system. These klystrons will be powered by state of the art solid-state high voltage modulators. A RF pulse compressor, similar to the SLED II pulse compressor, will compress the klystron output pulse with a power gain factor of five. For compactness consideration, we are looking at a folded waveguide setup. This will give us 500 MW at output of the compressor. The compressed pulse will then be distributed to the RF gun and to six traveling wave accelerator sections. Phase and amplitude control are located at the RF gun input and additional control points along the LINAC to allow for parameter control during operation. This high power RF system is being designed and constructed. In this paper, we will present the design, layout, and status of this RF system.

  5. Slide 1

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    New synthetic strategy for porous molecular materials towards gas separation Center for Gas Separations Relevant to Clean Energy Technologies Li & Zhou, Nat. Chem. 2010, 2, 893 PMOP-1 Breakthrough curve Mixture gas (CO 2 : N 2 = 10:90v%) : 10 sccm Time (min) 0 1 2 3 4 C/Co 0.0 0.2 0.4 0.6 0.8 1.0 Carbon dioxide Nitrogen Breakthrough of CO 2 -N 2 (1:9) 0 100 200 300 400 500 600 700 0 20 40 60 80 100 V ads (cm 3 /g, STP) P /mmHg N 2 H 2 O 2 Ar 0 100 200 300 400 500 600 700 0 10 20 30 40 50 60

  6. The Behavior of IAPWS-95 from 250 to 300 K and Pressures up to 400 MPa: Evaluation Based on Recently Derived Property Data

    SciTech Connect (OSTI)

    Wagner, Wolfgang Thol, Monika

    2015-12-15

    Over the past several years, considerable scientific and technical interest has been focused on accurate thermodynamic properties of fluid water covering part of the subcooled (metastable) region and the stable liquid from the melting line up to about 300 K and pressures up to several hundred MPa. Between 2000 and 2010, experimental density data were published whose accuracy was not completely clear. The scientific standard equation of state for fluid water, the IAPWS-95 formulation, was developed on the basis of experimental data for thermodynamic properties that were available by 1995. In this work, it is examined how IAPWS-95 behaves with respect to the experimental data published after 1995. This investigation is carried out for temperatures from 250 to 300 K and pressures up to 400 MPa. The starting point is the assessment of the current data situation. This was mainly performed on the basis of data for the density, expansivity, compressibility, and isobaric heat capacity, which were derived in 2015 from very accurate speed-of-sound data. Apart from experimental data and these derived data, property values calculated from the recently published equation of state for this region of Holten et al. (2014) were also used. As a result, the unclear data situation could be clarified, and uncertainty values could be estimated for the investigated properties. In the region described above, detailed comparisons show that IAPWS-95 is able to represent the latest experimental data for the density, expansivity, compressibility, speed of sound, and isobaric heat capacity to within the uncertainties given in the release on IAPWS-95. Since the release does not contain uncertainty estimates for expansivities and compressibilities, the statement relates to the error propagation of the given uncertainty in density. Due to the lack of experimental data for the isobaric heat capacity for pressures above 100 MPa, no uncertainty estimates are given in the release for this pressure

  7. Stress Corrosion Crack Growth Rate Testing and Analytical Electron Microscopy of Alloy 600 as a Function of Pourbaix Space and Microstructure

    SciTech Connect (OSTI)

    N. Lewis; S.A. Attanasio; D.S. Morton; G.A. Young

    2000-10-04

    Stress corrosion crack (SCC) growth rate tests and analytical electron microscopy (AEM) studies were performed over a broad range of environments and heat treatments of Alloy 600. This effort was conducted to correlate bulk environmental conditions such as pH and electrochemical potential (EcP) with the morphology of the SCC crack. Development of a library of AEM morphologies formed by SCC in different environments is an important step in identifying the conditions that lead to SCC in components. Additionally, AEM examination of stress corrosion cracks formed in different environments and microstructures lends insight into the mechanism(s) of stress corrosion cracking. Testing was conducted on compact tension specimens in three environments: a mildly acidic oxidizing environment containing sulfate ions, a caustic environment containing 10% NaOH, and hydrogenated near-neutral buffered water. Additionally, stress corrosion cracking testing of a smooth specimen was conducted in hydrogenated steam. The following heat treatments of Alloy 600 were examined: mill annealed at 980 C (near-neutral water), mill annealed at 1010 C (steam), sensitized (acid and caustic), and mill annealed + healed to homogenize the grain boundary Cr concentration (caustic). Crack growth rate (CGR) testing showed that sensitized Alloy 600 tested in the mildly acidic, oxidizing environment containing sulfate ions produced the fastest cracking ({approx} 8.8 {micro}m/hr at 260 C), and AEM examination revealed evidence of sulfur segregation to the crack tip. The caustic environment produced slower cracking ({approx} 0.4 {micro}m/hr at 307 C) in the mill annealed + healed heat treatment but no observed cracking in the sensitized condition. In the caustic environment, fully oxidized carbides were present in the crack wake but not ahead of the crack tip. In near-neutral buffered water at 338 C, the CGR was a function of dissolved hydrogen in the water and exhibited a maximum (0.17 {micro}m/hr) near the

  8. Generation and use of high power 213 nm and 266 nm laser radiation and tunable 210-400 nm laser radiation with BBO crystal matrix array

    DOE Patents [OSTI]

    Gruen, Dieter M.

    2000-01-01

    A 213 nm laser beam is capable of single photon ablative photodecomposition for the removal of a polymer or biological material substrate. Breaking the molecular bonds and displacing the molecules away from the substrate in a very short time period results in most of the laser photon energy being carried away by the displaced molecules, thus minimizing thermal damage to the substrate. The incident laser beam may be unfocussed and is preferably produced by quintupling the 1064 nm radiation from a Nd:YAG solid state laser, i.e., at 213 nm. In one application, the 213 nm laser beam is expanded in cross section and directed through a plurality of small beta barium borate (BBO) crystals for increasing the energy per photon of the laser radiation directed onto the substrate. The BBO crystals are arranged in a crystal matrix array to provide a large laser beam transmission area capable of accommodating high energy laser radiation without damaging the BBO crystals. The BBO crystal matrix array may also be used with 266 nm laser radiation for carrying out single or multi photon ablative photodecomposition. The BBO crystal matrix array may also be used in an optical parametric oscillator mode to generate high power tunable laser radiation in the range of 210-400 nm.

  9. Adiabatic release measurements in aluminum between 400 and 1200 GPa: Characterization of aluminum as a shock standard in the multimegabar regime

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Knudson, Marcus D.; Desjarlais, Michael P.; Pribram-Jones, Aurora

    2015-06-15

    Aluminum has been used prolifically as an impedance matching standard in the multimegabar regime (1 Mbar = 100 GPa), particularly in nuclear driven, early laser driven, and early magnetically driven flyer plate experiments. The accuracy of these impedance matching measurements depends upon the knowledge of both the Hugoniot and release or reshock response of aluminum. Here, we present the results of several adiabatic release measurements of aluminum from ~400–1200 GPa states along the principal Hugoniot using full density polymethylpentene (commonly known as TPX), and both ~190 and ~110 mg/cc silica aerogel standards. Additionally, these data were analyzed within the frameworkmore » of a simple, analytical model that was motivated by a first-principles molecular dynamics investigation into the release response of aluminum, as well as by a survey of the release response determined from several tabular equations of state for aluminum. Combined, this theoretical and experimental study provides a method to perform impedance matching calculations without the need to appeal to any tabular equation of state for aluminum. Furthermore, as an analytical model, this method allows for propagation of all uncertainty, including the random measurement uncertainties and the systematic uncertainties of the Hugoniot and release response of aluminum. This work establishes aluminum for use as a high-precision standard for impedance matching in the multimegabar regime.« less

  10. Adiabatic release measurements in aluminum between 400 and 1200 GPa: Characterization of aluminum as a shock standard in the multimegabar regime

    SciTech Connect (OSTI)

    Knudson, Marcus D.; Desjarlais, Michael P.; Pribram-Jones, Aurora

    2015-06-15

    Aluminum has been used prolifically as an impedance matching standard in the multimegabar regime (1 Mbar = 100 GPa), particularly in nuclear driven, early laser driven, and early magnetically driven flyer plate experiments. The accuracy of these impedance matching measurements depends upon the knowledge of both the Hugoniot and release or reshock response of aluminum. Here, we present the results of several adiabatic release measurements of aluminum from ~400–1200 GPa states along the principal Hugoniot using full density polymethylpentene (commonly known as TPX), and both ~190 and ~110 mg/cc silica aerogel standards. Additionally, these data were analyzed within the framework of a simple, analytical model that was motivated by a first-principles molecular dynamics investigation into the release response of aluminum, as well as by a survey of the release response determined from several tabular equations of state for aluminum. Combined, this theoretical and experimental study provides a method to perform impedance matching calculations without the need to appeal to any tabular equation of state for aluminum. Furthermore, as an analytical model, this method allows for propagation of all uncertainty, including the random measurement uncertainties and the systematic uncertainties of the Hugoniot and release response of aluminum. This work establishes aluminum for use as a high-precision standard for impedance matching in the multimegabar regime.

  11. Adiabatic release measurements in aluminum between 400-1200 GPa. Characterization of aluminum as a shock standard in the multimegabar regime

    SciTech Connect (OSTI)

    Knudson, Marcus D.; Desjarlais, Michael P.; Pribram-Jones, Aurora

    2015-06-15

    Aluminum has been used prolifically as an impedance matching standard in the multimegabar regime (1 Mbar = 100 GPa), particularly in nuclear driven, early laser driven, and early magnetically driven flyer plate experiments. The accuracy of these impedance matching measurements depends upon the knowledge of both the Hugoniot and release or reshock response of aluminum. Here, we present the results of several adiabatic release measurements of aluminum from ~4001200 GPa states along the principal Hugoniot using full density polymethylpentene (commonly known as TPX), and both ~190 and ~110 mg/cc silica aerogel standards. Additionally, these data were analyzed within the framework of a simple, analytical model that was motivated by a first-principles molecular dynamics investigation into the release response of aluminum, as well as by a survey of the release response determined from several tabular equations of state for aluminum. Combined, this theoretical and experimental study provides a method to perform impedance matching calculations without the need to appeal to any tabular equation of state for aluminum. Furthermore, as an analytical model, this method allows for propagation of all uncertainty, including the random measurement uncertainties and the systematic uncertainties of the Hugoniot and release response of aluminum. This work establishes aluminum for use as a high-precision standard for impedance matching in the multimegabar regime.

  12. Niche Application Opportunities

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Niche Application Opportunities Bart A. van Hassel United Technologies Research Center (UTRC), East Hartford, Connecticut, USA DOE Materials-Based Hydrogen Storage Summit Defining pathways for onboard automotive applications Golden, CO, USA January 27-28, 2015 This presentation does not contain any proprietary, confidential, or otherwise restricted information 1 10 100 1000 10000 0 100 200 300 400 500 600 700 800 900 1000 Useful Specific Power [W/kg] Useful Specific Energy [Wh/kg] Automotive 80

  13. Determination of the relative resistance to ignition of selected turbopump materials in high-pressure, high-temperature, oxygen environments, volume 3. Interim report

    SciTech Connect (OSTI)

    Stoltzfus, J.M.; Benz, F.J.

    1986-07-01

    Data is presented from frictional heating tests on pairs of different materials. Materials tested include: Hastelloy X, Inconel 600, Invar 36, Monel K-500, Monel 400, nickel 200, silicon carbide, stainless steels 316, and zirconium copper. In tests where pairs of different materials were rubbed together, the material rated less resistant to ignition in previous tests appeared to control the resistance to ignition of the pair.

  14. Appendix 6 of 6

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    6 of 6 Federal Fiscal year 2002 budget related documentation 1. ORP budget requirements 2. President's approved FY2002 budget - Conference Committee Report 3. November 27, 2001 letter from Assistant Secretary Roberson (FY2002 budget allocation) OFFICE OF RIVER PROTECTION FUNDING REQUIREMENTS AS OF FEBRUARY, 2002 Waste Treatment Plant (WTP) Requirements per approved BNI Baseline (Dollars in Millions) 0 100 200 300 400 500 600 700 800 900 1000 Beg. Balance Carryover 0 175 281 60 0 0 0 0 0 0 0

  15. Slide 1

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Principles Simulation and Model-Driven Isotopic Labeling Experiments Reveal Biomass Decomposition Pathways 1 Theory driven experimental confirmation Intensity (arb. units) 600 550 500 450 400 350 300 250 Temperature (K) H 2 (2amu) background DOCH 2 CH 2 OD HOCD 2 CD 2 OH 398K 322K 346K 432K (A) * Density functional theory (DFT) calculations of ethylene glycol decomposition on Pt(111) and Ni/Pt(111) reveal key differences between decomposition of highly functionalized oxygenates compared to

  16. BLAST: CORRELATIONS IN THE COSMIC FAR-INFRARED BACKGROUND AT 250, 350, AND 500 mum REVEAL CLUSTERING OF STAR-FORMING GALAXIES

    SciTech Connect (OSTI)

    Viero, Marco P.; Martin, Peter G.; Netterfield, Calvin B.; Ade, Peter A. R.; Griffin, Matthew; Hargrave, Peter C.; Mauskopf, Philip; Moncelsi, Lorenzo; Pascale, Enzo; Bock, James J.; Chapin, Edward L.; Halpern, Mark; Marsden, Gaelen; Devlin, Mark J.; Klein, Jeff; Gundersen, Joshua O.; Hughes, David H.; MacTavish, Carrie J.; Negrello, Mattia; Olmi, Luca

    2009-12-20

    We detect correlations in the cosmic far-infrared background due to the clustering of star-forming galaxies in observations made with the Balloon-borne Large Aperture Submillimeter Telescope, at 250, 350, and 500 mum. We perform jackknife and other tests to confirm the reality of the signal. The measured correlations are well fitted by a power law over scales of 5'-25', with DELTAI/I = 15.1% +- 1.7%. We adopt a specific model for submillimeter sources in which the contribution to clustering comes from sources in the redshift ranges 1.3 <= z <= 2.2, 1.5 <= z <= 2.7, and 1.7 <= z <= 3.2, at 250, 350, and 500 mum, respectively. With these distributions, our measurement of the power spectrum, P(k{sub t}heta), corresponds to linear bias parameters, b = 3.8 +- 0.6, 3.9 +- 0.6, and 4.4 +- 0.7, respectively. We further interpret the results in terms of the halo model, and find that at the smaller scales, the simplest halo model fails to fit our results. One way to improve the fit is to increase the radius at which dark matter halos are artificially truncated in the model, which is equivalent to having some star-forming galaxies at z >= 1 located in the outskirts of groups and clusters. In the context of this model, we find a minimum halo mass required to host a galaxy is log(M{sub min}/M{sub sun}) = 11.5{sup +0.4}{sub -0.1}, and we derive effective biases b{sub eff} = 2.2 +- 0.2, 2.4 +- 0.2, and 2.6 +- 0.2, and effective masses log(M{sub eff}/M{sub odot})=12.9+-0.3, 12.8 +- 0.2, and 12.7 +- 0.2, at 250, 350 and 500 mum, corresponding to spatial correlation lengths of r{sub 0} = 4.9, 5.0, and 5.2+-0.7 h{sup -1}Mpc, respectively. Finally, we discuss implications for clustering measurement strategies with Herschel and Planck.

  17. 500-watt commercialized concentrator system

    SciTech Connect (OSTI)

    Ronney, K.; Aerni, E.

    1983-02-01

    A passively cooled, single-axis tracking, polar-axis mounted photovoltaic concentrator system has been designed, fabricated, installed, and tested. System description, design considerations, system performance and a production cost estimate are detailed.

  18. Powered by 500 Trillion Calculations

    Office of Energy Efficiency and Renewable Energy (EERE)

    Argonne's supercomputer is using its superpowers to map the movement of red blood cells -- which will hopefully lead to better diagnoses and treatments for patients with blood flow complications.

  19. Thermal degradation of concrete in the temperature range from ambient to 315{degree} C (600{degree} F). Revision 10/96

    SciTech Connect (OSTI)

    Kassir, M.K.; Bandyopadhyay, K.K.; Reich, M.

    1996-10-01

    This report is concerned with determining the effect of elevated temperatures on the behavior of concrete. Emphasis is placed on quantifying the degree of potential degradation of the physical properties of concrete in high-level waste storage tanks. The temperature elevation range of interest is from ambient to 315 C (600 F). The literature has been reviewed to examine the applicable experimental data and quantify the degradation in the concrete and reinforcing steel. Since many variables and test conditions control the results in the data base, upper and lower bounds of the degraded properties at temperatures applicable to the environments of the storage tanks are summarized and presented in explicit forms. For properties with large data bases, a normal logarithmic distribution of the data is assumed and a statistical analysis is carried out to find the mean and 84% values of the degraded property in the temperature range of interest. Such results are useful in assessing the effect of elevated temperatures on the structural behavior of the tanks. In addition, the results provide the technical basis for a parametric study that may be necessary to investigate the thermal aspects of the structural integrity of the tanks. 50 refs., 23 figs.

  20. Interaction of thermo-mechanical processing parameters and stress corrosion cracking for two heats of Ni-Cr-Fe Alloy 600

    SciTech Connect (OSTI)

    Lynn, J.P.; Webb, G.L.

    1984-02-01

    The relationship between hot rolling parameters, annealing parameters, microstructures and stress corrosion cracking behavior of Ni-Cr-Fe Alloy 600 in deaerated primary plant grade water at 680{degrees}F was investigated. A high carbon (0.07%) and a medium carbon (0.04%) heat were hot rolled 20% or 80% starting at 3 different temperatures: below, near, and above the carbide solvus followed by annealing for 1 or 4 hours at a nominal temperature of 1600{degrees}F or 1900{degrees}F. Materials that are resistant to stress corrosion cracking were produced by hot rolling above the carbide solvus temperature followed by annealing at high temperatures (>1900{degrees}F). A combination of hot rolling below carbide solvus, large rolling reduction and a short annealing at a low temperature produced materials susceptible to stress corrosion cracking, especially for the high carbon heat. The resistant materials have by optical metallography as having carbide decorated grain boundaries, little intragranular carbide precipitation and good grainboundary correlation between a nital and a phosphoric acid etch. The susceptible materials as lack grain boundary carbide precipitation, have heavy intragranular carbide precipitation and lack grain boundary correlation between a nital and a phosphoric acid etch.

  1. Stress relief to prevent stress corrosion in the transition region of expanded Alloy 600 steam-generator tubing. Final report. [PWR

    SciTech Connect (OSTI)

    Woodward, J.; van Rooyen, D.

    1983-05-01

    The feasibility of preventing primary side roll transition cracking has been investigated, using induction heating to attain stress relief of expanded Ni-Cr-Fe Alloy 600 steam generator tubing. Work on rolled tubing and U-bends has shown that temperatures with which stress relief can be obtained range from 700 to 850/sup 0/C, with lower temperatures in this range requiring longer times at temperature to provide the requisite reduction in residual stresses. No work has yet been done outside this range. Preliminary tests, using induction heating, have been carried out on a mock tube sheet assembly, designed to the dimensions of a typical steam generator, and have identified the type of heating/cooling cycle that would occur in the tube sheet during a stress relief operation. Preliminary results show that the times to reach the higher temperatures in the range observed to give stress relief, of the order of 850/sup 0/C, can be as short as 8 seconds, and less with optimum coil design and power control.

  2. Investigation of the sulfur and lithium to sulfur ratio threshold in stress corrosion cracking of sensitized alloy 600 in borated thiosulfate solution

    SciTech Connect (OSTI)

    Bandy, R.; Kelly, K.

    1984-07-01

    The stress corrosion cracking of sensitized Alloy 600 was investigated in aerated solutions of sodium thiosulfate generally containing 1.3% boric acid. The aim of the investigation, among others, was to determine the existence, if any, of a threshold level of sulfur, and lithium to sulfur ratio governing the SCC. Specimens were first solution annealed at 1135/sup 0/C for 45 minutes, water quenched, and then sensitized at 621/sup 0/C for 18 hours. Reverse U-bends were tested at room temperature, whereas slow strain rate and constant load tests were performed at 80/sup 0/C. All tests were performed in solutions open to the atmosphere. The results indicate that in the borated thiosulfate solution containing 7 ppM sulfur, 5 ppM lithium as lithium hydroxide is sufficient to inhibit SCC in U-bends. The occurrence of inhibition seems to correlate to the rapid increase of pH and conductivity of the solution as a result of the lithium hydroxide addition. In the slow strain rate tests in the borated solution containing 0.7 ppM lithium as lithium hydroxide, significant stress corrosion cracking is observed at a sulfur level of 30 ppb, i.e., a lithium to sulfur ratio of 23. In a parallel test in 30 ppb sulfur level but without any lithium hydroxide, the stress corrosion cracking is more severe than that in the lithiated environment, thus implying that lithium hydroxide plays some role in the stress corrosion cracking inhibition.

  3. Interaction of thermo-mechanical processing parameters and stress corrosion cracking for two heats of Ni-Cr-Fe Alloy 600

    SciTech Connect (OSTI)

    Lynn, J.P.; Webb, G.L.

    1984-02-01

    The relationship between hot rolling parameters, annealing parameters, microstructures and stress corrosion cracking behavior of Ni-Cr-Fe Alloy 600 in deaerated primary plant grade water at 680[degrees]F was investigated. A high carbon (0.07%) and a medium carbon (0.04%) heat were hot rolled 20% or 80% starting at 3 different temperatures: below, near, and above the carbide solvus followed by annealing for 1 or 4 hours at a nominal temperature of 1600[degrees]F or 1900[degrees]F. Materials that are resistant to stress corrosion cracking were produced by hot rolling above the carbide solvus temperature followed by annealing at high temperatures (>1900[degrees]F). A combination of hot rolling below carbide solvus, large rolling reduction and a short annealing at a low temperature produced materials susceptible to stress corrosion cracking, especially for the high carbon heat. The resistant materials have by optical metallography as having carbide decorated grain boundaries, little intragranular carbide precipitation and good grainboundary correlation between a nital and a phosphoric acid etch. The susceptible materials as lack grain boundary carbide precipitation, have heavy intragranular carbide precipitation and lack grain boundary correlation between a nital and a phosphoric acid etch.

  4. Summary of Static power converters of 500 kW or less serving as the relay interface package for non-conventional generators''

    SciTech Connect (OSTI)

    Ball, G.J.; Blackburn, D.C. Jr.; Gish, W.

    1994-07-01

    The special publication was prepared by the Power System Relaying Committee of the IEEE to assist people involved in the installation, application, and operation of utility-interconnected dispersed storage and generation (DSG) systems of 500 kW or less. The energy sources considered are batteries, fuel cells, windmills and photovoltaic arrays. In most cases, the electrical energy produced is direct current, dc, which must be converted to alternating current, ac, for connection to the electric utility network. The interface between the dc source and the utility ac is often a static power converter (SPC). The purpose of the publication is to illustrate those SPC characteristics that can obviate the need for the interface relay protection package normally required by a utility. A qualifying SPC can detect utility system disturbances or other conditions that would require generator separation in addition to its normal function of protection and control of the DSG.

  5. Proposed amendment to presidential permit PP-63 and associated modifications to 500 kV international transmission line, Forbes, Minnesota to Manitoba, Canada. [Forbes Substation

    SciTech Connect (OSTI)

    Not Available

    1992-10-01

    This Addendum to the Final Environmental Assessment for the Proposed Amendment to Presidential Permit PP-63 and Associated Modifications to 500 kV International Transmission Line: Forbes, Minnesota to Manitoba, Canada (DOE/EA-587) addresses Northern States Power Company's (NSP) proposed expansion of the Forbes Substation. The applicant has requested that the expansion take place on the west side of the substation, within the existing property line, instead of on the north side as originally proposed. All of the proposed construction would take place on property already owned by NSP. DOE has reviewed the environmental impacts associated with this minor modification and has determined that the conclusions reached in the environmental assessment and Finding of No Significant Impact prepared in connection with NSP's original amendment request remain valid.

  6. 500 MW demonstration of advanced wall-fired combustion techniques for the reduction of nitrogen oxide emissions from coal-fired boilers

    SciTech Connect (OSTI)

    Sorge, J.N.; Larrimore, C.L.; Slatsky, M.D.; Menzies, W.R.; Smouse, S.M.; Stallings, J.W.

    1997-12-31

    This paper discusses the technical progress of a US Department of Energy Innovative Clean Coal Technology project demonstrating advanced wall-fired combustion techniques for the reduction of nitrogen oxide (NOx) emissions from coal-fired boilers. The primary objectives of the demonstration is to determine the long-term NOx reduction performance of advanced overfire air (AOFA), low NOx burners (LNB), and advanced digital control optimization methodologies applied in a stepwise fashion to a 500 MW boiler. The focus of this paper is to report (1) on the installation of three on-line carbon-in-ash monitors and (2) the design and results to date from the advanced digital control/optimization phase of the project.

  7. {sup 147}Sm(n,{alpha}) cross section measurements from 3 eV to 500 keV: Implications for explosive nucleosynthesis reaction rates

    SciTech Connect (OSTI)

    Gledenov, Yu. M.; Koehler, P. E.; Andrzejewski, J.; Guber, K. H.; Rauscher, T.

    2000-10-01

    We have measured the {sup 147}Sm(n,{alpha}) cross section from 3 eV to 500 keV. These data were used to test nuclear statistical models which must be relied on to calculate the rates for as yet unmeasurable reactions occurring in explosive nucleosynthesis scenarios. It was found that our data are in reasonably good agreement with the reaction rate predicted by an older model but that the rates predicted by two very recent models are roughly a factor of 3 different from the data (in opposite directions). A detailed analysis indicates the strong dependence on the employed optical {alpha} potentials. These results, together with counting rate estimates for future experiments indicate that (n,{alpha}) measurements will be useful for improving reaction rate predictions across the global range of masses needed for explosive nucleosynthesis calculations.

  8. Measurement of the parity-violating longitudinal single-spin asymmetry for W+- boson production in polarized proton-proton collisions at sqrt s = 500 GeV

    SciTech Connect (OSTI)

    Aggarwal, M.M.; Dunlop, J.; et al.

    2011-02-11

    We report the first measurement of the parity-violating single-spin asymmetries for midrapidity decay positrons and electrons from W{sup +} and W{sup -} boson production in longitudinally polarized proton-proton collisions at {radical}s = 500 GeV by the STAR experiment at RHIC. The measured asymmetries, A{sub L}{sup W+} = -0.27 {+-} 0.10(stat.) {+-} 0.02(syst.) {+-} 0.03(norm.) and A{sub L}{sup W-} = 0.14 {+-} 0.19(stat.) {+-} 0.02(syst.) {+-} 0.01(norm.), are consistent with theory predictions, which are large and of opposite sign. These predictions are based on polarized quark and antiquark distribution functions constrained by polarized deep-inelastic scattering measurements.

  9. Propagation and stability characteristics of a 500-m-long laser-based fiducial line for high-precision alignment of long-distance linear accelerators

    SciTech Connect (OSTI)

    Suwada, Tsuyoshi; Satoh, Masanori; Telada, Souichi; Minoshima, Kaoru

    2013-09-15

    A laser-based alignment system with a He-Ne laser has been newly developed in order to precisely align accelerator units at the KEKB injector linac. The laser beam was first implemented as a 500-m-long fiducial straight line for alignment measurements. We experimentally investigated the propagation and stability characteristics of the laser beam passing through laser pipes in vacuum. The pointing stability at the last fiducial point was successfully obtained with the transverse displacements of ±40 μm level in one standard deviation by applying a feedback control. This pointing stability corresponds to an angle of ±0.08 μrad. This report contains a detailed description of the experimental investigation for the propagation and stability characteristics of the laser beam in the laser-based alignment system for long-distance linear accelerators.

  10. Improvements in 500-kHz Ultrasonic Phased-Array Probe Designs for Evaluation of Thick Section Cast Austenitic Stainless Steel Piping Welds

    SciTech Connect (OSTI)

    Crawford, Susan L.; Cinson, Anthony D.; Moran, Traci L.; Anderson, Michael T.; Diaz, Aaron A.

    2011-02-01

    PNNL has been studying and performing confirmatory research on the inspection of piping welds in coarse-grained steels for over 30 years. More recent efforts have been the application of low frequency phased array technology to this difficult to inspect material. The evolution of 500 kHz PA probes and the associated electronics and scanning protocol are documented in this report. The basis for the probe comparisons are responses from one mechanical fatigue crack and two thermal fatigue cracks in large-bore cast mockup specimens on loan from the Electric Power Research Institution. One of the most significant improvements was seen in the use of piezo-composite elements in the later two probes instead of the piezo-ceramic material used in the prototype array. This allowed a reduction in system gain of 30 dB and greatly reduced electronic noise. The latest probe had as much as a 5 dB increase in signal to noise, adding to its flaw discrimination capability. The system electronics for the latest probe were fully optimized for a 500 kHz center frequency, however significant improvements were not observed in the center frequency of the flaw responses. With improved scanner capabilities, smaller step sizes were used, allowing both line and raster data improvements to be made with the latest probe. The small step sizes produce high resolution images that improve flaw discrimination and, along with the increased signal-to-noise ratio inherent in the latest probe design, enhanced detection of the upper regions of the flaw make depth sizing more plausible. Finally, the physical sizes of the probes were progressively decreased allowing better access to the area of interest on specimens with weld crowns, and the latest probe was designed with non-integral wedges providing flexibility in focusing on different specimen geometries.

  11. Ultrasound-Guided Radiological Placement of Central Venous Port via the Subclavian Vein: A Retrospective Analysis of 500 Cases at a Single Institute

    SciTech Connect (OSTI)

    Sakamoto, Noriaki Arai, Yasuaki Takeuchi, Yoshito Takahashi, Masahide Tsurusaki, Masakatsu; Sugimura, Kazuro

    2010-10-15

    The purpose of this study was to assess the technical success rate and adverse events (AEs) associated with ultrasound (US)-guided radiological placement (RP) of a central venous port (CVP) via the subclavian vein (SCV). Between April 2006 and May 2007, a total of 500 US-guided RPs of a CVP via the SCV were scheduled in 486 cancer patients (mean age {+-} SD, 54.1 {+-} 18.1 years) at our institute. Referring to the interventional radiology report database and patients' records, technical success rate and AEs relevant to CVP placement were evaluated retrospectively. The technical success rate was 98.6% (493/500). AEs occurred in 26 cases (5.2%) during follow-up (range, 1-1080 days; mean {+-} SD, 304.0 {+-} 292.1 days). AEs within 24 h postprocedure occurred in five patients: pneumothorax (n = 2), arterial puncture (n = 1), hematoma formation at the pocket site (n = 2), and catheter tip migration into the internal mammary vein (n = 1). There were seven early AEs: hematoma formation at the pocket site (n = 2), fibrin sheath formation around the indwelling catheter (n = 2), and catheter-related infections (n = 3). There were 13 delayed AEs: catheter-related infections (n = 7), catheter detachments (n = 3), catheter occlusion (n = 1), symptomatic thrombus in the SCV (n = 1), and catheter migration (n = 1). No major AEs, such as procedure-related death, air embolism, or events requiring surgical intervention, were observed. In conclusion, US-guided RP of a CVP via the SCV is highly appropriate, based on its high technical success rate and the limited number of AEs.

  12. Measurement of transmission efficiency for 400 MeV proton beam through collimator at Fermilab MuCool Test Area using Chromox-6 scintillation screen

    SciTech Connect (OSTI)

    Jana, M. R.; Chung, M.; Leonova, M.; Moretti, A.; Palmer, M.; Schwarz, T.; Tollestrup, A.; Yonehara, K.; Freemire, B.; Hanlet, P.; Torun, Y.

    2013-06-15

    The MuCool Test Area (MTA) at Fermilab is a facility to develop the technology required for ionization cooling for a future Muon Collider and/or Neutrino Factory. As part of this research program, feasibility studies of various types of RF cavities in a high magnetic field environment are in progress. As a unique approach, we have tested a RF cavity filled with a high pressure hydrogen gas with a 400 MeV proton beam in an external magnetic field (B = 3 T). Quantitative information about the number of protons passing through this cavity is an essential requirement of the beam test. The MTA is a flammable gas (hydrogen) hazard zone. Due to safety reasons, no active (energized) beam diagnostic instrument can be used. Moreover, when the magnetic field is on, current transformers (toroids) used for beam intensity measurements do not work due to the saturation of the ferrite material of the transformer. Based on these requirements, we have developed a passive beam diagnostic instrumentation using a combination of a Chromox-6 scintillation screen and CCD camera. This paper describes details of the beam profile and position obtained from the CCD image with B = 0 T and B = 3 T, and for high and low intensity proton beams. A comparison is made with beam size obtained from multi-wires detector. Beam transmission efficiency through a collimator with a 4 mm diameter hole is measured by the toroids and CCD image of the scintillation screen. Results show that the transmission efficiency estimated from the CCD image is consistent with the toroid measurement, which enables us to monitor the beam transmission efficiency even in a high magnetic field environment.

  13. Irradiation creep and density changes observed in MA957 pressurized tubes irradiated to doses of 40-110 dpa at 400-750°C in FFTF

    SciTech Connect (OSTI)

    Toloczko, Mychailo B.; Garner, Frank A.; Maloy, Stuart A.

    2012-12-30

    An irradiation creep and swelling study was performed on tubing constructed from the Y2O3-strengthened ODS ferritic steel MA957. As a result of the reduction operations during manufacture, the grains in the tubing were highly elongated in the direction of the tubing axis, with an aspect ratio of ~10:1. Pressurized creep tubes were irradiated in the Fast Flux Test Facility (FFTF) to doses ranging from 40 dpa to 110 dpa at temperatures ranging from 400 to 750°C. The diametral strains produced during irradiation exhibit very strong transient strains that are linearly dependent on stress and increase with irradiation temperature before reaching temperature-independent steady-state creep rates of 0.6-0.7 X 10-6 (MPa dpa)-1. Contributions to transient strains may not arise only from classical thermal creep or irradiation creep considerations, but also may result from an irradiation-stimulated growth process whereby the highly elongated grain structure reduces the aspect ratio to produce fatter grains and thereby increases in the tube diameter. One manifestation of this process is a change in tube diameter that is not accompanied by a density change characteristic of void swelling or precipitation-induced changes in lattice parameter. These results provide the first conclusive demonstration that resistance to irradiation creep can be extended to higher temperatures by dispersoid addition, and most importantly, this resistance is maintained to high radiation damage levels. However, the irradiation creep compliance is not reduced by dispersoid addition, casting some doubt on various proposed climb and glide mechanisms of irradiation creep.

  14. Effects of zinc additions on the stress corrosion crack growth rate of sensitized stainless steel, Alloy 600 and Alloy 182 weld metal in 288 C water

    SciTech Connect (OSTI)

    Andresen, P.L.; Angeliu, T.M.

    1995-09-01

    ZnO additions to boiling water reactor (BWR) water have been the focus of recent interest, primarily because of their beneficial influence in reducing buildup of radioactive species such as Co{sup 60} in the oxide film of structural components, e.g., stainless steel piping. The effect of ZnO additions on stress corrosion crack growth rates were studied using 1T CT fracture mechanics specimens of sensitized type 304 stainless steel, sensitized Alloy 600, and Alloy 182 weld metal exposed to {approx}288 C water containing various levels of dissolved oxygen and impurities. Zn levels of 5 to 100 ppb Zn{sup 2+} were evaluated and found to reduce crack growth rates for all materials and in all water chemistries. Many Zn tests involved long term exposure and were performed at somewhat reduced corrosion potential (e.g., from {approx}+200 to 0 {minus}+50 mV{sub she}); variations in corrosion potential from +200, to +50, to {minus}50 mV{sub she} clearly had an important effect. The benefit of Zn appeared to be most pronounced when the growth rate was decreased (e.g., by corrosion potential). This was consistent with the findings of mechanistic studies, which showed that Zn decreased the repassivation response at times >10{sup 4} s, which is associated with low crack tip strain rates, i.e., low growth rates. Reduced corrosion potentials are also expected to directly effect Zn, since high (crack mouth) corrosion potentials inhibit the transport of Zn{sup 2+} into the crack. Zn also increased the fracture strain of the oxide on stainless steel, and may also reduce crack growth rates by increasing the pH in the crack. Similar benefits are expected for other structural materials, such as nonsensitized or irradiated stainless steel, carbon steel, low alloy steel, and other nickel alloys.

  15. RangeTables.xlsx

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    30 35 40 45 eVcm²/mg) LET vs. Range in Si for 40 MeV SEE Beams 14 N 20 Ne 40 Ar 0 3 6 9 0 400 800 1200 1600 2000 2400 1 H 0 0.1 0.2 40 Ar 78 Kr 0 5 10 15 20 0 100 200 300 400 500 600 700 800 900 1000 1100 LET (Me Range in Silicon (µm) After aramica window and 30 mm of air 0 1000 2000 3000 4000 5000 6000 7000 8000

  16. Berkshire Gas - Residential Energy Efficiency Rebate Program...

    Broader source: Energy.gov (indexed) [DOE]

    400 Storage Water Heaters: 100 Condensing Stand Alone Water Heaters: 500 Tankless Water Heaters: 500 - 800 Heat Recovery Ventilator: 500 After-Market Boiler Reset...

  17. Design and development of Stirling engines for stationary power generation applications in the 500 to 3000 horsepower range. Volume 1. Technical report

    SciTech Connect (OSTI)

    Not Available,

    1980-09-15

    This project was Phase I of a multiphased program for the design and development of Stirling engines for stationary power generation applications in the 500 to 3000 horsepower range. Phase I comprised the conceptual design and associated cost estimates of a stationary Stirling engine capable of being fueled by a variety of heat sources, with emphasis on coal firing, followed by the preparation of a plan for implementing the design, fabrication and testing of a demonstration engine by 1985. The development and evaluation of conceptual designs have been separated into two broad categories: the A designs which represent the present state-of-the-art and which are demonstrable by 1985 with minimum technical risk; and the B designs which involve advanced technology and therefore would require significant research and development prior to demonstration and commercialization, but which may ultimately offer advantages in terms of lower cost, better performance, or higher reliability. The majority of the effort in Phase I was devoted to the A designs.

  18. Design and development of Stirling engines for stationary-power-generation applications in the 500- to 3000-horsepower range. Phase I final report

    SciTech Connect (OSTI)

    1980-10-01

    A program plan and schedule for the implementation of the proposed conceptual designs through the remaining four phases of the overall large Stirling engine development program was prepared. The objective of Phase II is to prepare more detailed designs of the conceptual designs prepared in Phase I. At the conclusion of Phase II, a state-of-the-art design will be selected from the candidate designs developed in Phase I for development. The objective of Phase III is to prepare manufacturing drawings of the candidate engine design. Also, detailed manufacturing drawings of both 373 kW (500 hp) and 746 kW (1000 hp) power pack skid systems will be completed. The power pack skid systems will include the generator, supporting skid, controls, and other supporting auxiliary subsystems. The Stirling cycle engine system (combustion system, Stirling engine, and heat transport system) will be mounted in the power pack skid system. The objective of Phase IV is to procure parts for prototype engines and two power pack skid systems and to assemble Engines No. 1 and 2. The objective of Phase V is to perform extensive laboratory and demonstration testing of the Stirling engines and power pack skid systems, to determine the system performance and cost and commercialization strategy. Scheduled over a 6 yr period the cost of phases II through V is estimated at $22,063,000. (LCL)

  19. Impact Mitigation and Monitoring of the BPA 500-kV Garrison-Taft Transmission Line : Effects on Elk Security and Hunter Opportunity, Final Report.

    SciTech Connect (OSTI)

    Canfield, Jodie E.

    1988-11-01

    This study was conducted by the Montana Department of Fish, Wildlife and Parks from 1984--1988 to assess the impacts of the Garrison-Taft segment of a 500-kV powerline on elk summer-fall habitat. Construction of the powerline began in 1983, and the powerline was energized in 1985. The Garrison-Taft powerline corridor crossed 251 km of mountainous terrain in western Montana; about 465 km of new roads were constructed to provide permanent access to the powerline towers. The objectives of the study were: (1) to monitor the effectiveness of mitigation measures, including timing restrictions on construction activities and road closures on newly-built access roads, and (2) to determine if opening previously-unroaded elk security habitats to hunters by powerline access roads affected elk habitat use, distribution, use of security areas, or elk harvest. In addition, both the potential for accelerated timber harvest in areas crossed by the powerline that would not have otherwise been logged because of marginal economics and lack of haul roads and the potential effect of powerline flashovers on future prescribed burning of elk winter-ranges were evaluated. 83 refs., 88 figs., 15 tabs.

  20. {sup 7}Li(n,{gamma}){sup 8}Li reaction and the S{sub 17} factor at E{sub c.m.}>500 keV

    SciTech Connect (OSTI)

    Nagai, Y.; Shima, T.; Tomyo, A.; Igashira, M.; Takaoka, T.; Kikuchi, T.; Mengoni, A.; Otsuka, T.

    2005-05-01

    The partial cross sections from the neutron capture state to the ground and first excited states in {sup 8}Li have been separately determined for the first time at stellar neutron energy. The direct and weak cascade {gamma} rays from the capture and first excited states to the ground state were measured by means of anti-Compton NaI(Tl) and anti-Compton HPGe spectrometers, respectively. The {gamma}-ray branching ratio and the cross sections thus determined agree with that for thermal neutrons assuming a 1/v neutron velocity dependence. By comparing the cross sections with calculations based on the nonresonant direct capture mechanism it is shown that the cross sections are sensitive to the interaction potential of the incident neutron with the {sup 7}Li target nucleus. This analysis confirms the possibility of deriving the parameters necessary for the calculation of the astrophysical S factor S{sub 17}(E) for the {sup 7}Be(p,{gamma}){sup 8}B reaction in the upper energy range above 500 keV.

  1. Cross Section and Parity-Violating Spin Asymmetries of W{sup {+-}} Boson Production in Polarized p+p Collisions at {radical}(s)=500 GeV

    SciTech Connect (OSTI)

    Adare, A.; Kinney, E.; Linden Levy, L. A.; Nagle, J. L.; Wysocki, M.; Afanasiev, S.; Isupov, A.; Litvinenko, A.; Malakhov, A.; Peresedov, V.; Rukoyatkin, P.; Zolin, L.; Aidala, C.; Brooks, M. L.; Butsyk, S.; Guo, L.; Jiang, X.; Kapustinsky, J.; Kunde, G. J.; Lee, D. M.

    2011-02-11

    Large parity-violating longitudinal single-spin asymmetries A{sub L}{sup e+}=-0.86{sub -0.14}{sup +0.30} and A{sub L}{sup e-}=0.88{sub -0.71}{sup +0.12} are observed for inclusive high transverse momentum electrons and positrons in polarized p+p collisions at a center-of-mass energy of {radical}(s)=500 GeV with the PHENIX detector at RHIC. These e{sup {+-}} come mainly from the decay of W{sup {+-}} and Z{sup 0} bosons, and their asymmetries directly demonstrate parity violation in the couplings of the W{sup {+-}} to the light quarks. The observed electron and positron yields were used to estimate W{sup {+-}} boson production cross sections for the e{sup {+-}} channels of {sigma}(pp{yields}W{sup +}X)xBR(W{sup +}{yields}e{sup +}{nu}{sub e})=144.1{+-}21.2(stat){sub -10.3}{sup +3.4}(syst){+-}21.6(norm) pb, and {sigma}(pp{yields}W{sup -}X)xBR(W{sup -}{yields}e{sup -}{nu}{sub e})=31.7{+-}12.1(stat){sub -8.2}{sup +10.1}(syst){+-}4.8(norm) pb.

  2. Towards a beyond 1 GHz solid-state nuclear magnetic resonance: External lock operation in an external current mode for a 500 MHz nuclear magnetic resonance

    SciTech Connect (OSTI)

    Takahashi, Masato; Maeda, Hideaki; Ebisawa, Yusuke; Tennmei, Konosuke; Yanagisawa, Yoshinori; Nakagome, Hideki; Hosono, Masami; Takasugi, Kenji; Hase, Takashi; Miyazaki, Takayoshi; Fujito, Teruaki; Kiyoshi, Tsukasa; Yamazaki, Toshio

    2012-10-15

    Achieving a higher magnetic field is important for solid-state nuclear magnetic resonance (NMR). But a conventional low temperature superconducting (LTS) magnet cannot exceed 1 GHz (23.5 T) due to the critical magnetic field. Thus, we started a project to replace the Nb{sub 3}Sn innermost coil of an existing 920 MHz NMR (21.6 T) with a Bi-2223 high temperature superconducting (HTS) innermost coil. Unfortunately, the HTS magnet cannot be operated in persistent current mode; an external dc power supply is required to operate the NMR magnet, causing magnetic field fluctuations. These fluctuations can be stabilized by a field-frequency lock system based on an external NMR detection coil. We demonstrate here such a field-frequency lock system in a 500 MHz LTS NMR magnet operated in an external current mode. The system uses a {sup 7}Li sample in a microcoil as external NMR detection system. The required field compensation is calculated from the frequency of the FID as measured with a frequency counter. The system detects the FID signal, determining the FID frequency, and calculates the required compensation coil current to stabilize the sample magnetic field. The magnetic field was stabilized at 0.05 ppm/3 h for magnetic field fluctuations of around 10 ppm. This method is especially effective for a magnet with large magnetic field fluctuations. The magnetic field of the compensation coil is relatively inhomogeneous in these cases and the inhomogeneity of the compensation coil can be taken into account.

  3. Improved low-lying energy levels determined from solar coronal forbidden and spin-forbidden lines in the 500-1500 A range

    SciTech Connect (OSTI)

    Feldman, U.; Doschek, G.A. . E-mail: george.doschek@nrl.navy.mil

    2007-09-15

    We list observed parity-forbidden and spin-forbidden lines in the 500-1600 A range emitted by solar coronal plasmas and derive improved energy levels from their wavelengths. The lines, emitted by astrophysical abundant elements, belong to transitions within the ground configurations of the type ns{sup 2} np {sup k}, for n = 2, 3 and k = 0-5, and between the lowest term of the first excited configuration 2s2p {sup k+1} and the 2s{sup 2}2p {sup k} ground configurations for k = 0, 1, 2. For each line we give the newly measured wavelength, and the measured or predicted wavelength from the NIST Atomic Spectra Database (ASD) (which except for a few cases includes the previously reported compilation of Kaufman and Sugar [J. Phys. Chem. Ref. Data 15 (1986) 321]), and the values of the transition probability taken from the ASD and CHIANTI database. The list contains measured wavelengths of 136 lines of which over 100 were not available for the Kaufman and Sugar compilation. In addition we provide energy levels that were derived from the reported lines.

  4. Cross Section and Parity-Violating Spin Asymmetries of W± Boston Production in Polarized p + p Collisions at √sNN = 500 GeV

    SciTech Connect (OSTI)

    Adare, A.; PHENIX Collaboration

    2011-02-11

    Large parity-violating longitudinal single-spin asymmetries A{sub L}{sup e+} = -0.86{sub -0.14}{sup +0.30} and A{sub L}{sup e-} = 0.88{sub -0.71}{sup +0.12} are observed for inclusive high transverse momentum electrons and positrons in polarized p+p collisions at a center-of-mass energy of {radical}s = 500 GeV with the PHENIX detector at RHIC. These e{sup {+-}} come mainly from the decay of W{sup {+-}} and Z{sup 0} bosons, and their asymmetries directly demonstrate parity violation in the couplings of the W{sup {+-}} to the light quarks. The observed electron and positron yields were used to estimate W{sup {+-}} boson production cross sections for the e{sup {+-}} channels of {sigma}(pp {yields} W{sup +}X) x BR(W{sup +} e{sup +}v{sub e}) 144.1 {+-} 21.2(stat){sub -10.3}{sup +3.4}(syst) {+-} 21.6(norm) pb, and {sigma}(pp {yields} W{sup -}X) x BR(W{sup -} {yields} e{sup -}v{sup -}) = 31.7 {+-} 12.1(stat){sub -8.2}{sup +10.1}(syst) {+-} 4.8(norm) pb.

  5. PRODUCTION OF PLUTONIUM FLUORIDE FROM BISMUTH PHOSPHATE PRECIPITATE CONTAINING PLUTONIUM VALUES

    DOE Patents [OSTI]

    Brown, H.S.; Bohlmann, E.G.

    1961-05-01

    A process is given for separating plutonium from fission products present on a bismuth phosphate carrier. The dried carrier is first treated with hydrogen fluoride at between 500 and 600 deg C whereby some fission product fluorides volatilize away from plutonium tetrafluoride, and nonvolatile fission product fluorides are formed then with anhydrous fluorine at between 400 and 500 deg C. Bismuth and plutonium distill in the form of volatile fluorides away from the nonvolatile fission product fluorides. The bismuth and plutonium fluorides are condensed at below 290 deg C.

  6. Electricity Advisory Committee (EAC) - 2012 Meetings | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    2 Meetings Electricity Advisory Committee (EAC) - 2012 Meetings MARCH 5 & 6, 2012 MEETING OF THE ELECTRICITY ADVISORY COMMITTEE Date: Monday, March 5, 2012 2:00 p.m. - 5:00 p.m. EDT / Dutch Treat Dinner 6:00 p.m. - 8 p.m. Date: Tuesday, March 6, 2012 8:00 a.m. - 4:00 p.m. EDT Location: Ronald Reagan Building, Horizon Room, 1300 Pennsylvania Ave. NW, Washington, DC JUNE 11 & 12, 2012 MEETING OF THE ELECTRICITY ADVISORY COMMITTEE Date: Monday, June 11, 2012 2:00 p.m. - 5:00 p.m. EDT /

  7. Assembly of 500,000 inter-specific catfish expressed sequence tags and large scale gene-associated marker development for whole genome association studies

    SciTech Connect (OSTI)

    Catfish Genome Consortium; Wang, Shaolin; Peatman, Eric; Abernathy, Jason; Waldbieser, Geoff; Lindquist, Erika; Richardson, Paul; Lucas, Susan; Wang, Mei; Li, Ping; Thimmapuram, Jyothi; Liu, Lei; Vullaganti, Deepika; Kucuktas, Huseyin; Murdock, Christopher; Small, Brian C; Wilson, Melanie; Liu, Hong; Jiang, Yanliang; Lee, Yoona; Chen, Fei; Lu, Jianguo; Wang, Wenqi; Xu, Peng; Somridhivej, Benjaporn; Baoprasertkul, Puttharat; Quilang, Jonas; Sha, Zhenxia; Bao, Baolong; Wang, Yaping; Wang, Qun; Takano, Tomokazu; Nandi, Samiran; Liu, Shikai; Wong, Lilian; Kaltenboeck, Ludmilla; Quiniou, Sylvie; Bengten, Eva; Miller, Norman; Trant, John; Rokhsar, Daniel; Liu, Zhanjiang

    2010-03-23

    Background-Through the Community Sequencing Program, a catfish EST sequencing project was carried out through a collaboration between the catfish research community and the Department of Energy's Joint Genome Institute. Prior to this project, only a limited EST resource from catfish was available for the purpose of SNP identification. Results-A total of 438,321 quality ESTs were generated from 8 channel catfish (Ictalurus punctatus) and 4 blue catfish (Ictalurus furcatus) libraries, bringing the number of catfish ESTs to nearly 500,000. Assembly of all catfish ESTs resulted in 45,306 contigs and 66,272 singletons. Over 35percent of the unique sequences had significant similarities to known genes, allowing the identification of 14,776 unique genes in catfish. Over 300,000 putative SNPs have been identified, of which approximately 48,000 are high-quality SNPs identified from contigs with at least four sequences and the minor allele presence of at least two sequences in the contig. The EST resource should be valuable for identification of microsatellites, genome annotation, large-scale expression analysis, and comparative genome analysis. Conclusions-This project generated a large EST resource for catfish that captured the majority of the catfish transcriptome. The parallel analysis of ESTs from two closely related Ictalurid catfishes should also provide powerful means for the evaluation of ancient and recent gene duplications, and for the development of high-density microarrays in catfish. The inter- and intra-specific SNPs identified from all catfish EST dataset assembly will greatly benefit the catfish introgression breeding program and whole genome association studies.

  8. Evaluation of the ²³⁹Pu prompt fission neutron spectrum induced by neutrons of 500 keV and associated covariances

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Neudecker, D.; Talou, P.; Kawano, T.; Smith, D. L.; Capote, R.; Rising, M. E.; Kahler, A. C.

    2015-08-01

    We present evaluations of the prompt fission neutron spectrum (PFNS) of ²³⁹Pu induced by 500 keV neutrons, and associated covariances. In a previous evaluation by Talou et al. 2010, surprisingly low evaluated uncertainties were obtained, partly due to simplifying assumptions in the quantification of uncertainties from experiment and model. Therefore, special emphasis is placed here on a thorough uncertainty quantification of experimental data and of the Los Alamos model predicted values entering the evaluation. In addition, the Los Alamos model was extended and an evaluation technique was employed that takes into account the qualitative differences between normalized model predicted valuesmore » and experimental shape data. These improvements lead to changes in the evaluated PFNS and overall larger evaluated uncertainties than in the previous work. However, these evaluated uncertainties are still smaller than those obtained in a statistical analysis using experimental information only, due to strong model correlations. Hence, suggestions to estimate model defect uncertainties are presented, which lead to more reasonable evaluated uncertainties. The calculated keff of selected criticality benchmarks obtained with these new evaluations agree with each other within their uncertainties despite the different approaches to estimate model defect uncertainties. The keff one standard deviations overlap with some of those obtained using ENDF/B-VII.1, albeit their mean values are further away from unity. Spectral indexes for the Jezebel critical assembly calculated with the newly evaluated PFNS agree with the experimental data for selected (n,γ) and (n,f) reactions, and show improvements for high-energy threshold (n,2n) reactions compared to ENDF/B-VII.1.« less

  9. Evaluation of the ²³⁹Pu prompt fission neutron spectrum induced by neutrons of 500 keV and associated covariances

    SciTech Connect (OSTI)

    Neudecker, D.; Talou, P.; Kawano, T.; Smith, D. L.; Capote, R.; Rising, M. E.; Kahler, A. C.

    2015-08-01

    We present evaluations of the prompt fission neutron spectrum (PFNS) of ²³⁹Pu induced by 500 keV neutrons, and associated covariances. In a previous evaluation by Talou et al. 2010, surprisingly low evaluated uncertainties were obtained, partly due to simplifying assumptions in the quantification of uncertainties from experiment and model. Therefore, special emphasis is placed here on a thorough uncertainty quantification of experimental data and of the Los Alamos model predicted values entering the evaluation. In addition, the Los Alamos model was extended and an evaluation technique was employed that takes into account the qualitative differences between normalized model predicted values and experimental shape data. These improvements lead to changes in the evaluated PFNS and overall larger evaluated uncertainties than in the previous work. However, these evaluated uncertainties are still smaller than those obtained in a statistical analysis using experimental information only, due to strong model correlations. Hence, suggestions to estimate model defect uncertainties are presented, which lead to more reasonable evaluated uncertainties. The calculated keff of selected criticality benchmarks obtained with these new evaluations agree with each other within their uncertainties despite the different approaches to estimate model defect uncertainties. The keff one standard deviations overlap with some of those obtained using ENDF/B-VII.1, albeit their mean values are further away from unity. Spectral indexes for the Jezebel critical assembly calculated with the newly evaluated PFNS agree with the experimental data for selected (n,γ) and (n,f) reactions, and show improvements for high-energy threshold (n,2n) reactions compared to ENDF/B-VII.1.

  10. Spectra of atomic sulfur {sup 1}D in transitions to autoionizing Rydberg states in the region of 75 800-89 500 cm{sup -1}

    SciTech Connect (OSTI)

    Pan, W.-C.; Chen, I-C.; Huang, T.-P.; Yuh, J.-Y.; Lee, Y.-Y.

    2008-10-07

    We recorded photoionization spectra of sulfur atoms in transitions from state {sup 1}D in the range of 75 800-89 500 cm{sup -1}. Dissociation of CS{sub 2} after photolysis at 193 nm produced these sulfur atoms in a singlet excited state; they were then ionized with synchrotron radiation (NSRRC, beamline U9CGM) at resolution of up to 3 cm{sup -1} and detected with a quadruple mass filter. Rydberg series 3s{sup 2}3p{sup 3}({sup 2}D{sub 3/2}{sup 0})nd[3/2] and 3s{sup 2}3p{sup 3}({sup 2}D{sub 5/2}{sup 0})ns[5/2] with n extending to 16 and 32, respectively, to limit {sup 2}D{sup 0} are assigned. New Rydberg series 3s{sup 2}3p{sup 3}({sup 2}D{sub 3/2}{sup 0})nd[1/2]{sub 1}, ({sup 2}D{sub 5/2}{sup 0})nd[5/2], and ({sup 2}D{sub 3/2}{sup 0})nd[5/2] with n from 5-9 for the former two series and 7-13 for the latter are assigned. A new Rydberg line at 85 335 cm{sup -1} is assigned to 3s{sup 2}3p{sup 3}({sup 2}D{sub 3/2}{sup 0})6d {sup 1}P.

  11. Cross sections for nuclide production in a {sup 56}Fe target irradiated by 300, 500, 750, 1000, 1500, and 2600 MeV protons compared with data on a hydrogen target irradiated by 300, 500, 750, 1000, and 1500 MeV/nucleon {sup 56}Fe ions

    SciTech Connect (OSTI)

    Titarenko, Yu. E.; Batyaev, V. F.; Titarenko, A. Yu.; Butko, M. A.; Pavlov, K. V.; Florya, S. N.; Tikhonov, R. S.; Mashnik, S. G.; Ignatyuk, A. V.; Titarenko, N. N.; Gudowski, W.; Tesinsky, M.; Persson, C.-M. L.; Abderrahim, H. Ait; Kumawat, H.; Duarte, H.

    2008-09-15

    This work presents the cross sections for radioactive nuclide production in {sup 56}Fe(p,x) reactions determined in six experiments using 300, 500, 750, 1000, 1500, and 2600 MeV protons of the external beam from the ITEP U-10 proton accelerator. In total, 221 independent and cumulative yields of radioactive residuals of half-lives from 6.6 min to 312 d have been obtained. The radioactive product nuclide yields were determined by direct {gamma}-spectrometry. The measured data have been compared with the experimental data obtained elsewhere by the direct and inverse kinematics methods and with calculation results of 15 different codes that simulated hadron-nucleus interactions: MCNPX (INCL, CEM2K, BERTINI, ISABEL), LAHET (BERTINI, ISABEL), CEM03 (.01, .G1, .S1), LAQGSM03 (.01, .G1, .S1), CASCADE-2004, LAHETO, and BRIEFF. Most of the data obtained here are in a good agreement with the inverse kinematics results and disprove the results of some earlier activation measurements that were quite different from the inverse kinematics measurements. The most significant calculation-to-experiment differences are observed in the yields of the A<30 light nuclei, indicating that further improvements in nuclear reaction models are needed, and pointing out as well to a necessity of more complete experimental measurements of such reaction products.

  12. Characterisation of amorphous silica in air-oxidised Ti3SiC2 at 500-1000 °C using secondary-ion mass spectrometry, nuclear magnetic resonance and transmission electron microscopy

    SciTech Connect (OSTI)

    Pang, W K; Low, I M; Hanna, J V

    2010-05-18

    In this paper we have described the use of secondary-ion mass spectrometry (SIMS), solid state {sup 29}Si magic-angle-spinning (MAS) nuclear magnetic resonance (NMR) and transmission electron microscopy (TEM) to detect the existence of amorphous silica in Ti{sub 3}SiC{sub 2} oxidised at 500-1000 C. The formation of amorphous SiO{sub 2} and growth of crystalline TiO{sub 2} with temperature was monitored using dynamic SIMS and synchrotron radiation diffraction. A duplex structure with an outer TiO{sub 2}-rich layer and an inner mixed layer of SiO{sub 2} and TiO{sub 2} was observed. Results of NMR and TEM verified for the first time the direct evidence of amorphous silica formation during the oxidation of Ti{sub 3}SiC{sub 2} at the temperature range 500-1000 C.

  13. RangeTables.xls

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    (MeVcm²/mg) LET vs. Range in Si for 25 MeV SEE Beams (low LET) 4 He 14 N 0 0.5 1 1.5 0 600 1200 1800 2400 3000 3600 4 He 14 N 22 Ne 0 1 2 3 4 5 6 7 8 9 10 0 100 200 300 400 500 600 700 800 900 1000 1100 LET (MeVcm²/mg) Range in Silicon (µm) LET vs. Range in Si for 25 MeV SEE Beams (low LET) After aramica window and 30 mm of air 4 He 14 N 0 0.5 1 1.5 0 600 1200 1800 2400 3000 3600 Range in Silicon (µm) 129 Xe 30 40 50 60 (MeVcm²/mg) LET vs. Range in Si for 25 MeV SEE Beams After aramica

  14. Laboratory-Scale Column Testing Using IONSIV IE-911 for Removing Cesium from Acidic Tank Waste Simulant. 2: Determination of Cesium Exchange Capacity and Effective Mass Transfer Coefficient from a 500-cm3 Column Experiement

    SciTech Connect (OSTI)

    T.J. Tranter; R.D. Tillotson; T.A. Todd

    2005-04-01

    A semi-scale column test was performed using a commercial form of crystalline silicotitanate (CST) for removing radio-cesium from a surrogate acidic tank solution, which represents liquid waste stored at the Idaho National Engineering and Environmental Laboratory (INEEL). The engineered form of CST ion exchanger, known as IONSIVtmIE-911 (UOP, Mt. Laurel,NJ, USA), was tested in a 500-cm3 column to obtain a cesium breakthrough curve. The cesium exchange capacity of this column matched that obtained from previous testing with a 15-mc3 column. A numerical algorithm using implicit finite difference approximations was developed to solve the governing mass transport equations for the CST columns. An effective mass transfer coefficient was derived from solving these equations for previously reported 15 cm3 tests. The effective mass transfer coefficient was then used to predict the cesium breakthrough curve for the 500-cm3 column and compared to the experimental data reported in this paper. The calculated breakthrough curve showed excellent agreement with the data from the 500-cm3 column even though the interstitial velocity was a factor of two greater. Thus, this approach should provide a reasonable method for scale up to larger columns for treating actual tank waste.

  15. Magnetic Nature of the 500 meV peak in La2−xSrxCuO4 Observed with Resonant Inelastic X-ray Scattering at the Cu K-edge

    SciTech Connect (OSTI)

    Hill, J.P.; Ellis, D.S.; Kim, J.; Wakimoto, S.; Birgeneau, R.J.; Shvyd’ko, Y.; Casa, D.; Gog, T.; Ishii, K.; Ikeuchi, K.; Paramekanti, A.; Kim, Y.-J.

    2010-02-15

    We present a comprehensive study of the temperature and doping dependence of the 500 meV peak observed at q = ({pi},0) in resonant inelastic x-ray scattering (RIXS) experiments on La{sub 2}CuO{sub 4}. The intensity of this peak persists above the Neel temperature (T{sub N} = 320 K), but decreases gradually with increasing temperature, reaching zero at around T = 500 K. The peak energy decreases with temperature in close quantitative accord with the behavior of the two-magnon B{sub 1g} Raman peak in La{sub 2}CuO{sub 4} and, with suitable rescaling, agrees with the Raman peak shifts in EuBa{sub 2}Cu{sub 3}O{sub 6} and K{sub 2}NiF{sub 4}. The overall dispersion of this excitation in the Brillouin zone is found to be in agreement with theoretical calculations for a two-magnon excitation. Upon doping, the peak intensity decreases analogous to the Raman mode intensity and appears to track the doping dependence of the spin-correlation length. Taken together, these observations strongly suggest that the 500 meV mode is magnetic in character and is likely a two-magnon excitation.

  16. Search for Scalar Diphoton Resonances in the Mass Range 65–600 GeV with the ATLAS Detector in pp Collision Data at s=8 TeV

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Aad, G.; Abbott, B.; Abdallah, J.; Abdel Khalek, S.; Abdinov, O.; Aben, R.; Abi, B.; Abolins, M.; AbouZeid, O. S.; Abramowicz, H.; et al

    2014-10-20

    A search for scalar particles decaying via narrow resonances into two photons in the mass range 65–600 GeV is performed using 20.3 fb₋1 of √s=8 TeV pp collision data collected with the ATLAS detector at the Large Hadron Collider. The recently discovered Higgs boson is treated as a background. No significant evidence for an additional signal is observed. The results are presented as limits at the 95% confidence level on the production cross section of a scalar boson times branching ratio into two photons, in a fiducial volume where the reconstruction efficiency is approximately independent of the event topology. Lastly,more » the upper limits set extend over a considerably wider mass range than previous searches.« less

  17. Influence of Composition, Helium Generation Rate and Dpa Rate on Neutron-Induced Swelling of Fe-15Cr-16Ni-0.25Ti Alloys in FFTF at {approx} 400 Degrees C

    SciTech Connect (OSTI)

    Okita, T; Wolfer, W G; Sato, T; Sekimura, N; Garner, F A

    2003-08-05

    Contrary to the behavior of swelling of f.c.c. Fe-15Cr-16Ni and Fe-15Cr-16Ni-0.25Ti alloys irradiated together in the same FFTF-MOTA experiment, Fe-15Cr-16Ti-0.25Ti-0.05C does not exhibit a dependence of swelling on dpa rate at {approx}400 C. The transient regime of swelling is prolonged by carbon addition, however. Addition of boron to the carbon-doped alloy decreases the swelling somewhat but does not restore the sensitivity to dpa rate. It appears that the primary influence of boron is chemical in nature, probably associated with boron's impact on the behavior of carbon. Boron's role as a source of helium is thought to be secondary.

  18. Line spectrum and ion temperature measurements from tungsten ions at low ionization stages in large helical device based on vacuum ultraviolet spectroscopy in wavelength range of 500–2200 Å

    SciTech Connect (OSTI)

    Oishi, T. Morita, S.; Goto, M.; Huang, X. L.; Zhang, H. M.

    2014-11-15

    Vacuum ultraviolet spectra of emissions released from tungsten ions at lower ionization stages were measured in the Large Helical Device (LHD) in the wavelength range of 500–2200 Å using a 3 m normal incidence spectrometer. Tungsten ions were distributed in the LHD plasma by injecting a pellet consisting of a small piece of tungsten metal and polyethylene tube. Many lines having different wavelengths from intrinsic impurity ions were observed just after the tungsten pellet injection. Doppler broadening of a tungsten candidate line was successfully measured and the ion temperature was obtained.

  19. Detection of Amorphous Silica in Air-Oxidized Ti3SiC2 at 500-1000°C by NMR and SIMS

    SciTech Connect (OSTI)

    Pang, Wei Kong; Low, I M; Hanna, J V

    2010-11-12

    The use of secondary-ion mass spectrometry (SIMS), nuclear magnetic resonance (NMR) and transmission electron microscopy (TEM) to detect the existence of amorphous silica in Ti3SiC2 oxidised at 500-1000 ºC is described. The formation of an amorphous SiO2 layer and its growth in thickness with temperature was monitored using dynamic SIMS. Results of NMR and TEM verify for the first time the direct evidence of amorphous silica formation during the oxidation of Ti3SiC2 at 1000 ºC.

  20. Correlation between Pd metal thickness and thermally stable perpendicular magnetic anisotropy features in [Co/Pd]{sub n} multilayers at annealing temperatures up to 500 °C

    SciTech Connect (OSTI)

    An, Gwang Guk; Lee, Ja Bin; Yang, Seung Mo; Yoon, Kap Soo; Kim, Jae Hong; Chung, Woo Seong; Hong, Jin Pyo

    2015-02-15

    We examine highly stable perpendicular magnetic anisotropy (PMA) features of [Co/Pd]{sub 10} multilayers (MLs) versus Pd thickness at various ex-situ annealing temperatures. Thermally stable PMA characteristics were observed up to 500 °C, confirming the suitability of these systems for industrial applications at this temperature. Experimental observations suggest that the choice of equivalent Co and Pd layer thicknesses in a ML configuration ensures thermally stable PMA features, even at higher annealing temperatures. X-ray diffraction patterns and cross-sectional transmission electron microscopy images were obtained to determine thickness, post-annealing PMA behavior, and to explore the structural features that govern these findings.

  1. September 8, 2011, HSS/Union Focus Group Work Group Telecom ...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AGENDA Work Group Framework 3:00 - 4:00 pm EST Introductory Remarks......Training Work Group 4:00 - 5:00 pm EST Introductory Remarks......

  2. Columbia Gas of Massachusetts - Residential Energy Efficiency...

    Broader source: Energy.gov (indexed) [DOE]

    Heaters: 400 Tankless Water Heaters: 500 - 800 Condensing Water Heater: 400 Storage Water Heaters: 100 Thermostat: 25 After Market Boiler Reset: 225 Heat Recovery...

  3. AT-400A compliance test report

    SciTech Connect (OSTI)

    Glass, R.E.

    1998-06-01

    In 1993 Sandia was directed to design containers for the long-term storage and transport of nuclear weapons origin fissile material. This program was undertaken at the direction of the US Department of Energy and in cooperation with Lawrence Livermore National Laboratory and Los Alamos National Laboratory. Lawrence Livermore National Laboratory and Los Alamos National Laboratory were tasked with developing the internal fixturing for the contents. The hardware is being supplied by AlliedSignal Federal Manufacturing and Technologies, and the packaging process has been developed at Mason and Hanger Corporation`s Pantex Plant. The unique challenge was to design a container that could be sealed with the fissile material contents; and, anytime during the next 50 years, the container could be transported with only the need for the pre-shipment leak test. This required a rigorous design capable of meeting the long-term storage and transportation requirements. This report addresses the final testing that was undertaken to demonstrate compliance with US radioactive materials transport regulations.

  4. Columbia Gas of Massachusetts - Commercial Energy Efficiency...

    Broader source: Energy.gov (indexed) [DOE]

    - 800 Indirect Water Heater: 400 Condensing Stand Alone Water Heaters: 500 Storage Water Heaters: 100 After Market Boiler Reset: 225 Commercial Griddles: 500 Gas Fryers...

  5. Word Pro - Untitled1

    U.S. Energy Information Administration (EIA) Indexed Site

    b Electric Noncoincident Peak Load and Capacity Margin: Winter Peak Period U.S.¹ Winter Peak Load,² All Interconnections, 1986-2011 Winter Capacity Margin, 1996-2011 U.S.¹ Winter Peak Load² by NERC³ Regional Assessment Area, 2011 U.S. Energy Information Administration / Annual Energy Review 2011 263 1986 1989 1992 1995 1998 2001 2004 2007 2010 0 100 200 300 400 500 600 700 Gigawatts 1996 1998 2000 2002 2004 2006 2008 2010 0 5 10 15 20 25 30 35 Percent 48 47 5 79 131 154 41 52 107 FRCC NPCC

  6. October 15 & 16, 2012 Meeting of the Electricity Advisory Committee |

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Department of Energy October 15 & 16, 2012 Meeting of the Electricity Advisory Committee October 15 & 16, 2012 Meeting of the Electricity Advisory Committee October 15 & 16, 2012 Meeting of the Electricity Advisory Committee Date: Monday, October 15, 2012 2:00 p.m. - 5:00 p.m. EDT / Dutch Treat Dinner 6:00 p.m. - 8 p.m. Date: Tuesday, October 16, 2012 8:00 a.m. - 4:00 p.m. EDT Location: Capital Hilton, 1001 16th St. NW, Washington, DC Overview The Department of Energy's

  7. March 5 & 6, 2012 Meeting of the Electricity Advisory Committee |

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Department of Energy March 5 & 6, 2012 Meeting of the Electricity Advisory Committee March 5 & 6, 2012 Meeting of the Electricity Advisory Committee March 5 & 6, 2012 Meeting of the Electricity Advisory Committee Date: Monday, March 5, 2012 2:00 p.m. - 5:00 p.m. EDT / Dutch Treat Dinner 6:00 p.m. - 8 p.m. Date: Tuesday, March 6, 2012 8:00 a.m. - 4:00 p.m. EDT Location: Ronald Reagan Building, Horizon Room, 1300 Pennsylvania Ave. NW, Washington, DC Overview The Department of

  8. Beamline 12.0.2

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    2 Print Coherent science Scientific disciplines: Applied science, magnetism, materials science Endstations: 12.0.2.1: Coherent optics 12.0.2.2: Coherent x-ray scattering GENERAL BEAMLINE INFORMATION Operational Yes Source characteristics Third harmonic of 8-cm-period undulator (U8) Energy range 300-1500 eV Monochromator VLS-PGM, with two gratings (600 and 1200 lines/mm) Calculated flux (1.9 GeV, 400 mA) 1013 photons/s/0.1%BW at 500 eV Resolving power (E/DE) 1,000 Beam size Focused: 70 x 10 µm

  9. Beamline 12.0.2

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    2 Print Coherent science Scientific disciplines: Applied science, magnetism, materials science Endstations: 12.0.2.1: Coherent optics 12.0.2.2: Coherent x-ray scattering GENERAL BEAMLINE INFORMATION Operational Yes Source characteristics Third harmonic of 8-cm-period undulator (U8) Energy range 300-1500 eV Monochromator VLS-PGM, with two gratings (600 and 1200 lines/mm) Calculated flux (1.9 GeV, 400 mA) 1013 photons/s/0.1%BW at 500 eV Resolving power (E/DE) 1,000 Beam size Focused: 70 x 10 µm

  10. Beamline 12.0.2

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    2 Print Coherent science Scientific disciplines: Applied science, magnetism, materials science Endstations: 12.0.2.1: Coherent optics 12.0.2.2: Coherent x-ray scattering GENERAL BEAMLINE INFORMATION Operational Yes Source characteristics Third harmonic of 8-cm-period undulator (U8) Energy range 300-1500 eV Monochromator VLS-PGM, with two gratings (600 and 1200 lines/mm) Calculated flux (1.9 GeV, 400 mA) 1013 photons/s/0.1%BW at 500 eV Resolving power (E/DE) 1,000 Beam size Focused: 70 x 10 µm

  11. Beamline 12.0.2

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    2 Print Coherent science Scientific disciplines: Applied science, magnetism, materials science Endstations: 12.0.2.1: Coherent optics 12.0.2.2: Coherent x-ray scattering GENERAL BEAMLINE INFORMATION Operational Yes Source characteristics Third harmonic of 8-cm-period undulator (U8) Energy range 300-1500 eV Monochromator VLS-PGM, with two gratings (600 and 1200 lines/mm) Calculated flux (1.9 GeV, 400 mA) 1013 photons/s/0.1%BW at 500 eV Resolving power (E/DE) 1,000 Beam size Focused: 70 x 10 µm

  12. Beamline 12.0.2

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    2 Print Coherent science Scientific disciplines: Applied science, magnetism, materials science Endstations: 12.0.2.1: Coherent optics 12.0.2.2: Coherent x-ray scattering GENERAL BEAMLINE INFORMATION Operational Yes Source characteristics Third harmonic of 8-cm-period undulator (U8) Energy range 300-1500 eV Monochromator VLS-PGM, with two gratings (600 and 1200 lines/mm) Calculated flux (1.9 GeV, 400 mA) 1013 photons/s/0.1%BW at 500 eV Resolving power (E/DE) 1,000 Beam size Focused: 70 x 10 µm

  13. Beamline 12.0.2

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    2 Print Coherent science Scientific disciplines: Applied science, magnetism, materials science Endstations: 12.0.2.1: Coherent optics 12.0.2.2: Coherent x-ray scattering GENERAL BEAMLINE INFORMATION Operational Yes Source characteristics Third harmonic of 8-cm-period undulator (U8) Energy range 300-1500 eV Monochromator VLS-PGM, with two gratings (600 and 1200 lines/mm) Calculated flux (1.9 GeV, 400 mA) 1013 photons/s/0.1%BW at 500 eV Resolving power (E/DE) 1,000 Beam size Focused: 70 x 10 µm

  14. Optimization of Storage vs. Compression Capacity

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Storage Volume vs. Compression Capacity Amgad Elgowainy Argonne National Laboratory Presentation at CSD Workshop Argonne National Laboratory March 21, 2013 0 5 10 15 20 25 0 100 200 300 400 500 600 700 800 900 0 15 30 45 60 75 90 105 120 135 150 Mass (Kg) Pressure (bar) and Temperature (K) Time (Sec) Low Pressure Cascade Mid Pressure Cascade High Pressure Pressure Mass Temperature Temperature Temperature 2 0 1 2 3 4 5 6 0 10 20 30 40 50 60 70 80 90 0 15 30 45 60 75 90 105 120 135 150 Mass (Kg)

  15. Buildings Energy Data Book: 7.6 Efficiency Standards for Lighting

    Buildings Energy Data Book [EERE]

    3 Efficiency Standards for Medium Base Compact Fluorescent Lamps (1) Factor Requirements Lamp Power (W) & Configuration Minimum Efficacy: lumens/watt (based upon initial lumen data) Bare Lamp: Lamp Power < 15 45.0 Lamp Power ≥ 15 60.0 Covered Lamp (no reflector): Lamp Power < 15 40.0 15 ≤ Lamp Power < 19 48.0 19 ≤ Lamp Power < 25 50.0 25 ≤ Lamp Power 55.0 Note(s): Source(s): 1) Effective for products manufactured on or after January 1, 2006

  16. Marketing to Win: How to Identify the Real Decision-maker and Tailor Your

    Energy Savers [EERE]

    Department of Energy March 5 & 6, 2012 Meeting of the Electricity Advisory Committee March 5 & 6, 2012 Meeting of the Electricity Advisory Committee March 5 & 6, 2012 Meeting of the Electricity Advisory Committee Date: Monday, March 5, 2012 2:00 p.m. - 5:00 p.m. EDT / Dutch Treat Dinner 6:00 p.m. - 8 p.m. Date: Tuesday, March 6, 2012 8:00 a.m. - 4:00 p.m. EDT Location: Ronald Reagan Building, Horizon Room, 1300 Pennsylvania Ave. NW, Washington, DC Overview The Department of

  17. PowerPoint Presentation

    U.S. Energy Information Administration (EIA) Indexed Site

    20 W 118 th St, New York, NY 10027 | http://energypolicy.columbia.edu | @ColumbiaUEnergy Pacific Rim Impacts of US Shale Boom Jason Bordoff 2013 EIA Energy Conference June 17, 2013 1 420 W 118 th St, New York, NY 10027 | http://energypolicy.columbia.edu | @ColumbiaUEnergy Global Gas Demand Forecast Bcf/d Source: IEA WEO2012 0 100 200 300 400 500 600 2010 2015 2020 2025 2030 2035 Non-OECD Asia OECD Asia Africa Middle East Non-OECD Europe/Eurasia Europe Non-OECD Americas OECD Americas 2 420 W 118

  18. PowerPoint Presentation

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    20 W 118 th St, New York, NY 10027 | http://energypolicy.columbia.edu | @ColumbiaUEnergy Pacific Rim Impacts of US Shale Boom Jason Bordoff 2013 EIA Energy Conference June 17, 2013 1 420 W 118 th St, New York, NY 10027 | http://energypolicy.columbia.edu | @ColumbiaUEnergy Global Gas Demand Forecast Bcf/d Source: IEA WEO2012 0 100 200 300 400 500 600 2010 2015 2020 2025 2030 2035 Non-OECD Asia OECD Asia Africa Middle East Non-OECD Europe/Eurasia Europe Non-OECD Americas OECD Americas 2 420 W 118

  19. Beamline 12.0.2

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    2 Print Coherent science Scientific disciplines: Applied science, magnetism, materials science Endstations: 12.0.2.1: Coherent optics 12.0.2.2: Coherent x-ray scattering GENERAL BEAMLINE INFORMATION Operational Yes Source characteristics Third harmonic of 8-cm-period undulator (U8) Energy range 300-1500 eV Monochromator VLS-PGM, with two gratings (600 and 1200 lines/mm) Calculated flux (1.9 GeV, 400 mA) 1013 photons/s/0.1%BW at 500 eV Resolving power (E/DE) 1,000 Beam size Focused: 70 x 10 µm

  20. Beamline 12.0.2

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    2 Print Coherent science Scientific disciplines: Applied science, magnetism, materials science Endstations: 12.0.2.1: Coherent optics 12.0.2.2: Coherent x-ray scattering GENERAL BEAMLINE INFORMATION Operational Yes Source characteristics Third harmonic of 8-cm-period undulator (U8) Energy range 300-1500 eV Monochromator VLS-PGM, with two gratings (600 and 1200 lines/mm) Calculated flux (1.9 GeV, 400 mA) 1013 photons/s/0.1%BW at 500 eV Resolving power (E/DE) 1,000 Beam size Focused: 70 x 10 µm

  1. EPA-600/4-84-040

    Office of Legacy Management (LM)

    r i n g Around U n i t e d States Nuclear Test Areas, Calendar Year 1983 compiled b y R. ... PREFACE The I1.S. Atomic Energy Commission (AEC) used t h e Nevada Test S i t e (NTS) from ...

  2. Geothermal Data Repository Reaches 500 Submissions | Department...

    Broader source: Energy.gov (indexed) [DOE]

    All projects receiving GTO funding upload their raw data-ranging from well and drilling data to tested exploration methodologies-to the GDR. Ensuring access to the data is not just ...

  3. Proposed Amendment to Presidential Permit PP-63 and Associated Modifications to 500-kV International Transmission Line: Forbes, Minnesota to Manitoba, Canada, Northern States Power Company. Addendum to the final Environmental Assessment

    SciTech Connect (OSTI)

    Not Available

    1992-10-01

    This Addendum to the Final Environmental Assessment for the Proposed Amendment to Presidential Permit PP-63 and Associated Modifications to 500 kV International Transmission Line: Forbes, Minnesota to Manitoba, Canada (DOE/EA-587) addresses Northern States Power Company`s (NSP) proposed expansion of the Forbes Substation. The applicant has requested that the expansion take place on the west side of the substation, within the existing property line, instead of on the north side as originally proposed. All of the proposed construction would take place on property already owned by NSP. DOE has reviewed the environmental impacts associated with this minor modification and has determined that the conclusions reached in the environmental assessment and Finding of No Significant Impact prepared in connection with NSP`s original amendment request remain valid.

  4. Proposed amendment to presidential permit PP-63 and associated modifications to 500 kV international transmission line, Forbes, Minnesota to Manitoba, Canada. Addendum to the final environmental assessment

    SciTech Connect (OSTI)

    Not Available

    1992-10-01

    This Addendum to the Final Environmental Assessment for the Proposed Amendment to Presidential Permit PP-63 and Associated Modifications to 500 kV International Transmission Line: Forbes, Minnesota to Manitoba, Canada (DOE/EA-587) addresses Northern States Power Company`s (NSP) proposed expansion of the Forbes Substation. The applicant has requested that the expansion take place on the west side of the substation, within the existing property line, instead of on the north side as originally proposed. All of the proposed construction would take place on property already owned by NSP. DOE has reviewed the environmental impacts associated with this minor modification and has determined that the conclusions reached in the environmental assessment and Finding of No Significant Impact prepared in connection with NSP`s original amendment request remain valid.

  5. Innovative Clean Coal Technology (ICCT): 500 MW demonstration of advanced wall-fired combustion techniques for the reduction of nitrogen oxide (NO{sub x}) emissions from coal-fired boilers. Phase 3B LNB AOFA tests

    SciTech Connect (OSTI)

    Smith, L.L.; Larsen, L.L.

    1993-12-13

    This Innovative Clean Coal Technology II project seeks to evaluate NO{sub x} control techniques on a 500 MW(e) utility boiler. This report is provided to document the testing performed and results achieved during Phase 3B--Low NO{sub x} Burner Retrofit with Advanced Overfire Air (AOFA). This effort began in May 1993 following completion of Phase 3A--Low-NO{sub x} Burner Testing. The primary objective of the Phase 3B test effort was to establish LNB plus AOFA retrofit NO{sub x} emission characteristics under short-term well controlled conditions and under long-term normal system load dispatch conditions. In addition, other important performance data related to the operation of the boiler in this retrofit configuration were documented for comparison to those measured during the Phase 1 baseline test effort. Protocols for data collection and instrumentation operation were established during Phase 1 (see Phase 1 Baseline Tests Report).

  6. Measurement of the ?*? distribution of muon pairs with masses between 30 and 500 GeV in 10.4 fb-1 of pp collisions

    SciTech Connect (OSTI)

    Abazov, Victor Mukhamedovich

    2015-04-06

    We present a measurement of the distribution of the variable ?*? for muon pairs with masses between 30 and 500 GeV, using the complete run II data set collected by the D0 detector at the Fermilab Tevatron proton-antiproton collider. This corresponds to an integrated luminosity of 10.4 fb1 at ?s = 1.96 TeV. The data are corrected for detector effects and presented in bins of dimuon rapidity and mass. The variable ?*? probes the same physical effects as the Z/?* boson transverse momentum, but is less susceptible to the effects of experimental resolution and efficiency. These are the first measurements at any collider of the ?*? distributions for dilepton masses away from the Z ? ?+? boson mass peak. As a result, the data are compared to QCD predictions based on the resummation of multiple soft gluons.

  7. Measurement of the {sup 237}Np(n,{gamma}) cross section from 20 meV to 500 keV with a high efficiency, highly segmented 4{pi} BaF{sub 2} detector

    SciTech Connect (OSTI)

    Esch, E.-I.; Bond, E. M.; Bredeweg, T. A.; Couture, A.; Glover, S. E.; Haight, R. C.; Jandel, M.; Kawano, T.; Mertz, A.; O'Donnell, J. M.; Rundberg, R. S.; Schwantes, J. M.; Ullmann, J. L.; Vieira, D. J.; Wilhelmy, J. B.; Wouters, J. M.; Reifarth, R.; Greife, U.; Hatarik, A. M.; Hatarik, R.

    2008-03-15

    The {sup 237}Np(n,{gamma}){sup 238}Np cross section has been measured in the neutron energy range from 20 meV to 500 keV using the DANCE array at the Los Alamos National Laboratory. This new facility allows experiments with submilligram samples and is therefore well suited to investigate isotopes with half-lives as low as a few hundred days. In this benchmark measurement, only 0.42 mg of {sup 237}Np was sufficient to determine differential cross sections relative to the well-known resonance at 0.5 eV. The thermal cross section was measured to {sigma}{sub 2200m/s}=177{+-}5 barn, {sigma}{sub kT=25.3meV}=167{+-}4 barn and the resonance integral to RI=693{+-}6 barn.

  8. Measurement of the Parity-Violating Longitudinal Single-Spin Asymmetry for W{sup {+-}} Boson Production in Polarized Proton-Proton Collisions at {radical}(s)=500 GeV

    SciTech Connect (OSTI)

    Aggarwal, M. M.; Bhati, A. K.; Pruthi, N. K.; Ahammed, Z.; Dong, X.; Grebenyuk, O.; Hjort, E.; Jacobs, P.; Kikola, D. P.; Kiryluk, J.; Klein, S. R.; Masui, H.; Matis, H. S.; Naglis, M.; Odyniec, G.; Olson, D.; Ploskon, M. A.; Poskanzer, A. M.; Powell, C. B.; Ritter, H. G.

    2011-02-11

    We report the first measurement of the parity-violating single-spin asymmetries for midrapidity decay positrons and electrons from W{sup +} and W{sup -} boson production in longitudinally polarized proton-proton collisions at {radical}(s)=500 GeV by the STAR experiment at RHIC. The measured asymmetries, A{sub L}{sup W+}=-0.27{+-}0.10(stat.){+-}0.02(syst.){+-}0.03(norm.) and A{sub L}{sup W-}=0.14{+-}0.19(stat.){+-}0.02(syst.){+-}0.01(norm.), are consistent with theory predictions, which are large and of opposite sign. These predictions are based on polarized quark and antiquark distribution functions constrained by polarized deep-inelastic scattering measurements.

  9. Measurement of the parity-violating longitudinal single-spin asymmetry for W{sup {+-}} boson production in polarized proton-proton collisions at {radical}(s) = 500 GeV

    SciTech Connect (OSTI)

    Igo, G.

    2011-07-15

    We report the first measurement of the parity violating single-spin asymmetries for midrapidity decay positrons and electrons from W{sup +} and W{sup -} boson production in longitudinally polarized proton-proton collisions at {radical}(s) = 500 GeV by the STAR experiment at RHIC. The measured asymmetries, A{sub L}{sup W+} = -0.27{+-}0.10(stat.){+-}0.02(syst.){+-}0.03(norm.) and A{sub L}{sup W-} 0.14{+-}0.19(stat.){+-}0.02(syst.){+-}0.01(norm.), are consistent with theory predictions, which are large and of opposite sign. These predictions are based on polarized quark and antiquark distribution functions constrained by polarized DIS measurements.

  10. Guidance on the Use of Hand-Held Survey Meters for radiological Triage: Time-Dependent Detector Count Rates Corresponding to 50, 250, and 500 mSv Effective Dose for Adult Males and Adult Females

    SciTech Connect (OSTI)

    Bolch, W.E.; Hurtado, J.L.; Lee, C.; Manger, Ryan P; Hertel, Nolan; Burgett, E.; Dickerson, W.

    2012-01-01

    In June 2006, the Radiation Studies Branch of the Centers for Disease Control and Prevention held a workshop to explore rapid methods of facilitating radiological triage of large numbers of potentially contaminated individuals following detonation of a radiological dispersal device. Two options were discussed. The first was the use of traditional gamma cameras in nuclear medicine departments operated as makeshift wholebody counters. Guidance on this approach is currently available from the CDC. This approach would be feasible if a manageable number of individuals were involved, transportation to the relevant hospitals was quickly provided, and the medical staff at each facility had been previously trained in this non-traditional use of their radiopharmaceutical imaging devices. If, however, substantially larger numbers of individuals (100 s to 1,000 s) needed radiological screening, other options must be given to first responders, first receivers, and health physicists providing medical management. In this study, the second option of the workshop was investigated by the use of commercially available portable survey meters (either NaI or GM based) for assessing potential ranges of effective dose (G50, 50Y250, 250Y500, and 9500 mSv). Two hybrid computational phantoms were used to model an adult male and an adult female subject internally contaminated with 241Am, 60Cs, 137Cs, 131I, or 192Ir following an acute inhalation or ingestion intake. As a function of time following the exposure, the net count rates corresponding to committed effective doses of 50, 250, and 500 mSv were estimated via Monte Carlo radiation transport simulation for each of four different detector types, positions, and screening distances. Measured net count rates can be compared to these values, and an assignment of one of four possible effective dose ranges could be made. The method implicitly assumes that all external contamination has been removed prior to screening and that the measurements be

  11. China has 6,000-mile pipeline system

    SciTech Connect (OSTI)

    Ming, S.

    1983-08-01

    A dramatic change has taken place in China's oil transport system, with pipelines replacing tank-cars as the most important means of transport for crude oil and petroleum products. According to Petroleum Ministry officials, the volume of crude oil carried by China's pipeline system increased from 23.2 percent in 1971 to 65.6 percent in 1981, while the volume delivered by tank-cars declined from 61.11 percent to 8.4 percent. The remainder was transported by tankers. China's 9,700 km (6,000-mile) pipeline network includes 5,600 km (3,500 miles) designed to carry crude oil and more than 600 km (375 miles) for petroleum products, plus 3,400 km (2,100 miles), mostly in Sichuan province, for natural gas.

  12. Measurement of the φ*η distribution of muon pairs with masses between 30 and 500 GeV in 10.4 fb-1 of pp¯ collisions

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Abazov, Victor Mukhamedovich

    2015-04-06

    We present a measurement of the distribution of the variable φ*η for muon pairs with masses between 30 and 500 GeV, using the complete run II data set collected by the D0 detector at the Fermilab Tevatron proton-antiproton collider. This corresponds to an integrated luminosity of 10.4 fb–1 at √s = 1.96 TeV. The data are corrected for detector effects and presented in bins of dimuon rapidity and mass. The variable φ*η probes the same physical effects as the Z/γ* boson transverse momentum, but is less susceptible to the effects of experimental resolution and efficiency. These are the first measurementsmore » at any collider of the φ*η distributions for dilepton masses away from the Z → ℓ+ℓ– boson mass peak. As a result, the data are compared to QCD predictions based on the resummation of multiple soft gluons.« less

  13. Measurement of the φ*η distribution of muon pairs with masses between 30 and 500 GeV in 10.4 fb-1 of pp¯ collisions

    SciTech Connect (OSTI)

    Abazov, Victor Mukhamedovich

    2015-04-06

    We present a measurement of the distribution of the variable φ*η for muon pairs with masses between 30 and 500 GeV, using the complete run II data set collected by the D0 detector at the Fermilab Tevatron proton-antiproton collider. This corresponds to an integrated luminosity of 10.4 fb–1 at √s = 1.96 TeV. The data are corrected for detector effects and presented in bins of dimuon rapidity and mass. The variable φ*η probes the same physical effects as the Z/γ* boson transverse momentum, but is less susceptible to the effects of experimental resolution and efficiency. These are the first measurements at any collider of the φ*η distributions for dilepton masses away from the Z → ℓ+ boson mass peak. As a result, the data are compared to QCD predictions based on the resummation of multiple soft gluons.

  14. Measurement of the Φ η * distribution of muon pairs with masses between 30 and 500 GeV in 10.4 fb - 1 of p p ¯ collisions

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Abazov, V. M.; Abbott, B.; Acharya, B. S.; Adams, M.; Adams, T.; Agnew, J. P.; Alexeev, G. D.; Alkhazov, G.; Alton, A.; Askew, A.; et al

    2015-04-06

    We present a measurement of the distribution of the variable Φ*η for muon pairs with masses between 30 and 500 GeV, using the complete run II data set collected by the D0 detector at the Fermilab Tevatron proton-antiproton collider. This corresponds to an integrated luminosity of 10.4 fb⁻¹ at √s=1.96 TeV. The data are corrected for detector effects and presented in bins of dimuon rapidity and mass. The variable Φ*η probes the same physical effects as the Z/γ* boson transverse momentum, but is less susceptible to the effects of experimental resolution and efficiency. These are the first measurements at anymore » collider of the Φ*η distributions for dilepton masses away from the Z→l⁺l⁻ boson mass peak. The data are compared to QCD predictions based on the resummation of multiple soft gluons.« less

  15. Cross Section and Parity Violating Spin Asymmetries of W plus or minus Boson Production in Polarized p+p Collisions at s=500 GeV

    SciTech Connect (OSTI)

    Adare, A.; Awes, Terry C; Cianciolo, Vince; Efremenko, Yuri; Enokizono, Akitomo; Read Jr, Kenneth F; Silvermyr, David O; Sorensen, Soren P; Stankus, Paul W; PHENIX, Collaboration

    2011-01-01

    Large parity-violating longitudinal single-spin asymmetries A{sub L}{sup e+} = -0.86{sub -0.14}{sup +0.30} and A{sub L}{sup e-} = 0.88{sub -0.71}{sup +0.12} are observed for inclusive high transverse momentum electrons and positrons in polarized p+p collisions at a center-of-mass energy of {radical}s = 500 GeV with the PHENIX detector at RHIC. These e{sup {+-}} come mainly from the decay of W{sup {+-}} and Z{sup 0} bosons, and their asymmetries directly demonstrate parity violation in the couplings of the W{sup {+-}} to the light quarks. The observed electron and positron yields were used to estimate W{sup {+-}} boson production cross sections for the e{sup {+-}} channels of {sigma}(pp {yields} W{sup +}X) x BR(W{sup +} {yields} e{sup +}{nu}{sub e}) = 144.1 {+-} 21.2(stat){sub -10.3}{sup +3.4}(syst) {+-} 21.6(norm) pb, and {sigma}(pp {yields} W{sup -}X) x BR(W{sup -} {yields} e{sup -} {bar {nu}}{sub e}) = 31.7 {+-} 12.1(stat){sub -8.2}{sup +10.1}(syst) {+-} 4.8(norm) pb.

  16. Automated setup for magnetic hysteresis characterization based on a voltage controlled current source with 500 kHz full power bandwidth and 10 A peak-to-peak current

    SciTech Connect (OSTI)

    Calabrese, G.; Capineri, L.; Granato, M.; Frattini, G.

    2015-04-15

    This paper describes the design of a system for the characterization of magnetic hysteresis behavior in soft ferrite magnetic cores. The proposed setup can test magnetic materials exciting them with controlled arbitrary magnetic field waveforms, including the capability of providing a DC bias, in a frequency bandwidth up to 500 kHz, with voltages up to 32 V peak-to-peak, and currents up to 10 A peak-to-peak. In order to have an accurate control of the magnetic field waveform, the system is based on a voltage controlled current source. The electronic design is described focusing on closed loop feedback stabilization and passive components choice. The system has real-time hysteretic loop acquisition and visualization. The comparisons between measured hysteresis loops of sample magnetic materials and datasheet available ones are shown. Results showing frequency and thermal behavior of the hysteresis of a test sample prove the system capabilities. Moreover, the B-H loops obtained with a multiple waveforms excitation signal, including DC bias, are reported. The proposal is a low-cost and replicable solution for hysteresis characterization of magnetic materials used in power electronics.

  17. Hot Electron Diagnostic in a Solid Laser Target by Buried K-Shell Fluorer Technique from Ultra-Intense (3x1020W/cm2,< 500 J) Laser-Plasma Interactions on the Petawatt Laser at LLNL

    SciTech Connect (OSTI)

    Yasuike, K.; Key, M.H.; Hatchett, S.P.; Snavely, R.A.

    2000-06-29

    Characterization of hot electron production (a conversion efficiency from laser energy into electrons) in ultra intense laser-solid target interaction, using 1.06 {micro}m laser light with an intensity of up to 3 x 10{sup 20}W cm{sup -2} and an on target laser energy of {le}500 J, has been done by observing K{sub {beta}} as well as K{sub {alpha}} emissions from a buried Mo layer in the targets, which are same structure as in the previous 100 TW experiments but done under less laser intensity and energy conditions ({le} 4 x 10{sup 19} Wcm{sup -2} and {le} 30 J). The conversion efficiency from the laser energy into the energy, carried by hot electrons, has been estimated to be {approx}50%, which are little bit higher than the previous less laser energy ({approx} 20 J) experiments, yet the x-ray emission spectra from the target has change drastically, i.e., gamma flash.

  18. Semi-exclusive structure functions and inclusive form factors for ed{yields}e{sup '}{pi}NN in the energy region from threshold up to 500 MeV

    SciTech Connect (OSTI)

    Darwish, E.M. Al-Thoyaib, S.S.

    2009-08-15

    The separated structure functions R{sub L}, R{sub T}, R{sub LT}, and R{sub TT} governing the semi-exclusive differential cross section for the d(e,e{sup '}{pi})NN reaction are evaluated in the energy region from threshold up to 500 MeV. We present results for both the neutral and the charged pion production channels in a variety of kinematic settings. For the elementary pion electroproduction operator, the realistic unitary isobar MAID-2003 model is used which gives a good description of the process on the free nucleon. The completely inclusive form factors, which determine the inclusive differential cross section when only the scattered electron is detected, are also computed. It has been found that the structure functions and form factors reveal clear differences between the production dynamics for the {pi}{sup 0} and {pi}{sup {+-}} pions. Considerable dependencies of the structure functions and form factors on the pion angle and virtual photon lab-energy are found. The predicted results are found to be insensitive to the potential model used for the deuteron wave function.

  19. Branching ratio measurements of the predissociation of {sup 12}C{sup 16}O by time-slice velocity-map ion imaging in the energy region from 108 000 to 110 500 cm{sup -1}

    SciTech Connect (OSTI)

    Gao Hong; Song Yu; Yang Lei; Shi Xiaoyu; Ng, C. Y.; Jackson, William M.; Yin Qingzhu

    2012-07-21

    Direct branching ratio measurements of the three lowest dissociation channels of {sup 12}C{sup 16}O that produce C({sup 3}P) + O({sup 3}P), C({sup 1}D) + O({sup 3}P), and C({sup 3}P) + O({sup 1}D) are reported in the vacuum ultraviolet region from 108 000 cm{sup -1} (92.59 nm) to 110 500 cm{sup -1} (90.50 nm) using the time-slice velocity-map ion imaging and nonlinear resonant four-wave mixing techniques. Rotationally, resolved carbon ion yield spectra for both {sup 1}{Sigma}{sup +} and {sup 1}{Pi} bands of CO in this region have been obtained. Our measurements using this technique show that the branching ratio in this energy region, especially the relative percentages of the two spin-forbidden channels, is strongly dependent on the particular electronic and vibrational energy levels of CO that are excited.

  20. Design and development of Stirling Engines for stationary power generation applications in the 500 to 3000 hp range. Subtask 1A report: state-of-the-art conceptual design

    SciTech Connect (OSTI)

    1980-03-01

    The first portion of the Conceptual Design Study of Stirling Engines for Stationary Power Application in the 500 to 3000 hp range which was aimed at state-of-the-art stationary Stirling engines for a 1985 hardware demonstration is summarized. The main goals of this effort were to obtain reliable cost data for a stationary Stirling engine capable of meeting future needs for total energy/cogeneration sysems and to establish a pragmatic and conservative base design for a first generation hardware. Starting with an extensive screening effort, 4 engine types, i.e., V-type crank engine, radial engine, swashplate engine, and rhombic drive engine, and 3 heat transport systems, i.e., heat pipe, pressurized gas heat transport loop, and direct gas fired system, were selected. After a preliminary layout cycle, the rhombic drive engine was eliminated due to intolerable maintenance difficulties on the push rod seals. V, radial and swashplate engines were taken through a detailed design/layout cycle, to establish all important design features and reliable engine weights. After comparing engine layouts and analyzing qualitative and quantitative evaluation criteria, the V-crank engine was chosen as the candidate for a 1985 hardware demonstration.