National Library of Energy BETA

Sample records for 500 400 300

  1. Evaluations of University of Wisconsin Silicon Carbide Temperature Monitors 300 LO and 400 LO B

    SciTech Connect (OSTI)

    K. L. Davis; J. L. Rempe; D. L. Knudson; B. M. Chase; T. C. Unruh

    2011-12-01

    Silicon carbide (SiC) temperature monitors 05R4-02-A KG1403 (300 LO) and 05R4-01-A KG1415 (400 LO B) were evaluated at the High Temperature Test Lab (HTTL) to determine their peak irradiation temperatures. HTTL measurements indicate that the peak irradiation temperature for the 300 LO monitor was 295 {+-} 20 C and the peak irradiation temperature for the 400 LO B monitor was 294 {+-} 25 C. Two silicon carbide (SiC) temperature monitors irradiated in the Advanced Test Reactor (ATR) were evaluated at the High Temperature Test Lab (HTTL) to determine their peak temperature during irradiation. These monitors were irradiated as part of the University of Wisconsin Pilot Project with a target dose of 3 dpa. Temperature monitors were fabricated from high density (3.203 g/cm3) SiC manufactured by Rohm Haas with a nominal size of 12.5 mm x 1.0 mm x 0.75 mm (see Attachment A). Table 1 provides identification for each monitor with an expected peak irradiation temperature range based on preliminary thermal analysis (see Attachment B). Post irradiation calculations are planned to reduce uncertainties in these calculated temperatures. Since the early 1960s, SiC has been used as a post-irradiation temperature monitor. As noted in Reference 2, several researchers have observed that neutron irradiation induced lattice expansion of SiC annealed out when the post-irradiation annealing temperature exceeds the peak irradiation temperature. As noted in Reference 3, INL uses resistivity measurements to infer peak irradiation temperature from SiC monitors. Figure 1 depicts the equipment at the HTTL used to evaluate the SiC monitors. The SiC monitors are heated in the annealing furnace using isochronal temperature steps that, depending on customer needs, can range from 50 to 800 C. This furnace is located under a ventilation hood within the stainless steel enclosure. The ventilation system is activated during heating so that any released vapors are vented through this system. Annealing temperatures are recorded using a National Institute of Standards and Technology (NIST) traceable thermocouple inserted into an alumina tube in the furnace. After each isochronal annealing, the specimens are placed in a specialized fixture located in the constant temperature chamber (maintained at 30 C) for a minimum of 30 minutes. After the 30 minute wait time, each specimen's resistance is measured using the specialized fixture and a calibrated DC power analyzer. This report discusses the evaluation of the SiC monitors and presents the results. Testing was conducted in accordance with Reference 3. Sections 2 and 3 present the data collected for each monitor and provide interpretation of the data. Section 4 presents the evaluated temperature results.

  2. Corrosion of high temperature alloys in solar salt at 400, 500, and 680%C2%B0C.

    SciTech Connect (OSTI)

    Kruizenga, Alan Michael; Gill, David Dennis; LaFord, Marianne Elizabeth

    2013-09-01

    Corrosion tests at 400, 500, and 680%C2%B0C were performed using four high temperature alloys; 347SS, 321SS In625, and HA230. Molten salt chemistry was monitored over time through analysis of nitrite, carbonate, and dissolved metals. Metallography was performed on alloys at 500 and 680%C2%B0C, due to the relatively thin oxide scale observed at 400%C2%B0C. At 500%C2%B0C, corrosion of iron based alloys took the form of chromium depletion and iron oxides, while nickel based alloys also had chromium depletion and formation of NiO. Chromium was detected in relatively low concentrations at this temperature. At 680%C2%B0C, significant surface corrosion occurred with metal losses greater than 450microns/year after 1025hours of exposure. Iron based alloys formed complex iron, sodium, and chromium oxides. Some data suggests grain boundary chromium depletion of 321SS. Nickel alloys formed NiO and metallic nickel corrosion morphologies, with HA230 displaying significant internal oxidation in the form of chromia. Nickel alloys both exhibited worse corrosion than iron based alloys likely due to preferential dissolution of chromium, molybdenum, and tungsten.

  3. Design and Construction of a 500 KW CW, 400 MHZ Klystron To Be Used As RF Power Source For LHC/RF Component Tests

    SciTech Connect (OSTI)

    Pearson, Chris

    2003-05-05

    A 500 kW cw klystron operating at 400 MHz was developed and constructed jointly by CERN and SLAC for use as a high-power source at CERN for testing LHC/RF components such as circulators, RF absorbers and superconducting cavities with their input couplers. The design is a modification of the 353 MHz SLAC PEP-I klystron. More than 80% of the original PEP-I tube parts could thus be incorporated in the LHC test klystron which resulted in lower engineering costs as well as reduced development and construction time. The physical length between cathode plane and upper pole plate was kept unchanged so that a PEP-I tube focusing solenoid, available at CERN, could be re-used. With the aid of the klystron simulation codes JPNDISK and CONDOR, the design of the LHC tube was accomplished, which resulted in a tube with noticeably higher efficiency than its predecessor, the PEP-I klystron. The integrated cavities were redesigned using SUPERFISH and the output coupling circuit, which also required redesigning, was done with the aid of MAFIA. Details of the tube development and test results are presented.

  4. Measurement of residual nucleus cross sections and recoil energies in p + Fe collisions at 300, 500, 750, 1000 and 1500 MeV

    SciTech Connect (OSTI)

    Villagrasa, C.; Boudard, A.; Ducret, J.-E.; Fernandez, B.; Leray, S.; Volant, C.; Wlazlo, W.; Audouin, L.; Ferran, L.; Rejmund, F.

    2005-05-24

    The production of residual nuclei in p + Fe collisions has been measured at GSI on the FRS facility by means of the reverse kinematic techniques at 300, 500, 750, 1000 and 1500 MeV/A. The cross-sections larger than 0.01 mb of all isotopes with Z larger than 8 have been obtained. Velocity distributions were also measured. Comparisons to models describing spallation reactions and some empirical formulae often used in astrophysics are presented. These data are directly used to calculate impurity production and DPAs in a thin window as foreseen in spallation sources or accelerator-driven systems.

  5. C-H surface diamond field effect transistors for high temperature (400 °C) and high voltage (500 V) operation

    SciTech Connect (OSTI)

    Kawarada, H.; Tsuboi, H.; Naruo, T.; Yamada, T.; Xu, D.; Daicho, A.; Saito, T.; Hiraiwa, A.

    2014-07-07

    By forming a highly stable Al{sub 2}O{sub 3} gate oxide on a C-H bonded channel of diamond, high-temperature, and high-voltage metal-oxide-semiconductor field-effect transistor (MOSFET) has been realized. From room temperature to 400 °C (673 K), the variation of maximum drain-current is within 30% at a given gate bias. The maximum breakdown voltage (V{sub B}) of the MOSFET without a field plate is 600 V at a gate-drain distance (L{sub GD}) of 7 μm. We fabricated some MOSFETs for which V{sub B}/L{sub GD} > 100 V/μm. These values are comparable to those of lateral SiC or GaN FETs. The Al{sub 2}O{sub 3} was deposited on the C-H surface by atomic layer deposition (ALD) at 450 °C using H{sub 2}O as an oxidant. The ALD at relatively high temperature results in stable p-type conduction and FET operation at 400 °C in vacuum. The drain current density and transconductance normalized by the gate width are almost constant from room temperature to 400 °C in vacuum and are about 10 times higher than those of boron-doped diamond FETs.

  6. Cross sections for nuclide production in a {sup 56}Fe target irradiated by 300, 500, 750, 1000, 1500, and 2600 MeV protons compared with data on a hydrogen target irradiated by 300, 500, 750, 1000, and 1500 MeV/nucleon {sup 56}Fe ions

    SciTech Connect (OSTI)

    Titarenko, Yu. E.; Batyaev, V. F.; Titarenko, A. Yu.; Butko, M. A.; Pavlov, K. V.; Florya, S. N.; Tikhonov, R. S.; Mashnik, S. G.; Ignatyuk, A. V.; Titarenko, N. N.; Gudowski, W.; Tesinsky, M.; Persson, C.-M. L.; Abderrahim, H. Ait; Kumawat, H.; Duarte, H.

    2008-09-15

    This work presents the cross sections for radioactive nuclide production in {sup 56}Fe(p,x) reactions determined in six experiments using 300, 500, 750, 1000, 1500, and 2600 MeV protons of the external beam from the ITEP U-10 proton accelerator. In total, 221 independent and cumulative yields of radioactive residuals of half-lives from 6.6 min to 312 d have been obtained. The radioactive product nuclide yields were determined by direct {gamma}-spectrometry. The measured data have been compared with the experimental data obtained elsewhere by the direct and inverse kinematics methods and with calculation results of 15 different codes that simulated hadron-nucleus interactions: MCNPX (INCL, CEM2K, BERTINI, ISABEL), LAHET (BERTINI, ISABEL), CEM03 (.01, .G1, .S1), LAQGSM03 (.01, .G1, .S1), CASCADE-2004, LAHETO, and BRIEFF. Most of the data obtained here are in a good agreement with the inverse kinematics results and disprove the results of some earlier activation measurements that were quite different from the inverse kinematics measurements. The most significant calculation-to-experiment differences are observed in the yields of the A<30 light nuclei, indicating that further improvements in nuclear reaction models are needed, and pointing out as well to a necessity of more complete experimental measurements of such reaction products.

  7. 300 Area - Hanford Site

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    300 Area 324 Building 325 Building 400 AreaFast Flux Test Facility 618-10 and 618-11 Burial Grounds 700 Area B Plant B Reactor C Reactor Canister Storage Building and Interim ...

  8. TOP500 | National Nuclear Security Administration

    National Nuclear Security Administration (NNSA)

    TOP500

  9. RENEW300: Advancing Renewable Energy at HUD-Assisted Housing...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Minneapolis RENEW300: Advancing Renewable Energy at HUD-Assisted Housing - Minneapolis June 24, 2016 8:00AM to 4:00PM CDT Minneapolis, Minnesota

  10. Kinetics following addition of sulfur fluorides to a weakly ionized plasma from 300 to 500 K: Rate constants and product determinations for ion-ion mutual neutralization and thermal electron attachment to SF{sub 5}, SF{sub 3}, and SF{sub 2}

    SciTech Connect (OSTI)

    Shuman, Nicholas S.; Miller, Thomas M.; Viggiano, A. A.; Hazari, Nilay; Luzik, Eddie D. Jr.

    2010-12-21

    Rate constants for several processes including electron attachment to SF{sub 2}, SF{sub 3}, and SF{sub 5} and individual product channels of ion-ion mutual neutralization between SF{sub 6}{sup -}, SF{sub 5}{sup -}, and SF{sub 4}{sup -} with Ar{sup +} were determined by variable electron and neutral density attachment mass spectrometry. The experiments were conducted with a series of related neutral precursors (SF{sub 6}, SF{sub 4}, SF{sub 5}Cl, SF{sub 5}C{sub 6}H{sub 5}, and SF{sub 3}C{sub 6}F{sub 5}) over a temperature range of 300-500 K. Mutual neutralization rate constants for SF{sub 6}{sup -}, SF{sub 5}{sup -}, and SF{sub 4}{sup -} with Ar{sup +} are reported with uncertainties of 10-25% and show temperature dependencies in agreement with the theoretical value of T{sup -0.5}. Product branching in the mutual neutralizations is temperature independent and dependent on the electron binding energy of the anion. A larger fraction of product neutrals from the SF{sub 6}{sup -} mutual neutralization (0.9 {+-}0.1) are dissociated than in the SF{sub 5}{sup -} mutual neutralization (0.65 {+-} 0.2), with the SF{sub 4}{sup -} (0.7 {+-} 0.3) likely lying in between. Electron attachment to SF{sub 5} (k= 2.0 x 10{sup -8} {+-}{sub 1}{sup 2} cm{sup 3} s{sup -1} at 300 K) and SF{sub 3} (4 {+-} 3 x 10{sup -9} cm{sup 3} s{sup -1} at 300 K) show little temperature dependence. Rate constants of electron attachment to closed-shell SF{sub n} species decrease as the complexity of the neutral decreases.

  11. Electrical conductivity of Ca{sub 1-x}Sr{sub x}Ti{sub 0.65}Fe{sub 0.35}O{sub 3-{delta}}, x = 0, 0.5 and 1, polycrystalline compounds in the 300-500 K range

    SciTech Connect (OSTI)

    Muccillo, R.; Carmo, J.R.

    2012-05-15

    Highlights: Black-Right-Pointing-Pointer Fe-doped Sr and Ca titanates were synthesized by chemical and solid state reaction. Black-Right-Pointing-Pointer SPM images show striking differences in samples prepared by the two routes. Black-Right-Pointing-Pointer Impedance spectroscopy measurements show different electrical behaviors. Black-Right-Pointing-Pointer Correlations between the two macroscopic observations are shown. -- Abstract: Bulk and grain boundary electrical conductivity of oxygen deficient Ca{sub x}Sr{sub 1-x}Ti{sub 0.65}Fe{sub 0.35}O{sub 3-{delta}}, x = 0, 0.5 and 1.0, polycrystalline specimens were evaluated by impedance spectroscopy measurements in the 5 Hz-13 MHz frequency range from 300 to 500 K. The ceramic powders were synthesized by solid state reaction and by a chemical route, the polymeric precursor technique. The X-ray diffraction of the samples at room temperature shows the following perovskite crystalline structures: cubic for x = 0 and orthorhombic for x = 0.5 and 1.0. The impedance plots are composed of two semicircles ascribed to grains (bulk) and interfaces (grain boundaries) contributions. The impedance data show that sintered pellets using powders prepared by solid state synthesis present higher intergranular and intragranular resistivity values than pellets prepared by the chemical route. Observations of scanning probe microscopy topographic images of the surfaces of the sintered pellets show evident differences between the grain morphology of the pellets prepared with powders synthesized by the two routes.

  12. Oxford System 400

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Oxford Plasmalab System 400 Sputtering System For questions concerning this machines capabilities, please contact Varshni Singh, at 578-0248. ecr.jpg (48456 bytes) &nbsp: ecr1.jpg (68318 bytes) The Oxford System 400 produces uniform metallic films for use in the LIGA process at CAMD. This tool is equipped with two DC and one RF magnetron sputter targets for deposition of Cu, Ni, and Ti respectively. A load lock and rotating table allow deposition of up to four wafers during a single run.

  13. An experimental study of the solubility of molybdenum in H2O and KCl-H2O solutions from 500 ºC to 800 ºC, and 150 to 300 MPa

    SciTech Connect (OSTI)

    Ulrich, Thomas; Mavrogenes, John

    2008-04-22

    The solubility of molybdenum (Mo) was determined at temperatures from 500 °C to 800 °C and 150 to 300 MPa in KCl-H2O and pure H2O solutions in cold-seal experiments. The solutions were trapped as synthetic fluid inclusions in quartz at experimental conditions, and analyzed by laser ablation inductively coupled plasma mass spectrometry (LA ICPMS). Mo solubilities of 1.6 wt% in the case of KCl-bearing aqueous solutions and up to 0.8 wt% in pure H2O were found. Mo solubility is temperature dependent, but not pressure dependent over the investigated range, and correlates positively with salinity (KCl concentration). Molar ratios of ~1 for Mo/Cl and Mo/K are derived based on our data. In combination with results of synchrotron X-ray absorption spectroscopy of individual fluid inclusions, it is suggested that Mo-oxo-chloride complexes are present at high salinity (>20 wt% KCl) and ion pairs at moderate to low salinity (<11 wt% KCl) in KCl-H2O aqueous solutions. Similarly, in the pure H2O experiments molybdic acid is the dominant species in aqueous solution. The results of these hydrothermal Mo experiments fit with earlier studies conducted at lower temperatures and indicate that high Mo concentrations can be transported in aqueous solutions. Therefore, the Mo concentration in aqueous fluids seems not to be the limiting factor for ore formation, whereas precipitation processes and the availability of sulfur appear to be the main controlling factors in the formation of molybdenite (MoS2).

  14. ALSNews Vol. 300

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    0 ALSNews Vol. 300 Print Wednesday, 29 July 2009 00:00 In This Issue Towards Heavy Fermions in Europium Intermetallic Compounds Stochastic Domain-Wall Depinning in Magnetic...

  15. Hanford 300 Area ROD

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    300 Area ROD Briefing to the Hanford Advisory Board March 6, 2014 Larry Gadbois -- EPA Recap of the 300 Area ROD Primary new concept -- Uranium Sequestration: * Purpose: Accelerate restoration of groundwater uranium contamination. * Protect groundwater from downward leaching from the vadose zone (overlying soil). * Add phosphate to chemically bond with uranium into geologically stable autunite. Does not dissolve. * Dissolve phosphate in water, apply at ground surface, inject into the ground,

  16. Geothermal Data Repository Reaches 500 Submissions | Department...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Geothermal Data Repository Reaches 500 Submissions Geothermal Data Repository Reaches 500 Submissions August 25, 2015 - 2:41pm Addthis Geothermal Data Repository Reaches 500 ...

  17. 300ºC DDS + 300ºC MWD

    Broader source: Energy.gov [DOE]

    300ºC DDS + 300ºC MWD presentation at the April 2013 peer review meeting held in Denver, Colorado.

  18. President Obama Announces $400 Million Conditional Commitment...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    400 Million Conditional Commitment Offer to Support Solar Panel Manufacturing President Obama Announces 400 Million Conditional Commitment Offer to Support Solar Panel ...

  19. Tracker 300 Software

    Energy Science and Technology Software Center (OSTI)

    2006-01-12

    The Tracker300 software is downloaded to an off-the-shelf product called RCM3400/RCM3410 made by Rabbit Semiconductor. The software is a closed loop control which computes the sun's position and provides stability compensation. Using the RCM3400/RCM3410 module, the software stores and retrieves parameters from the onboard flash. The software also allows for communication with a host. It will allow the parameters to be downloaded or uploaded, it will show the status of the controller, it will providemore » real-time feedback, and it will send command acknowledgements. The software will capture the GPS response and ensure the internal clock is set correctly.« less

  20. Microsoft PowerPoint - BSQ-300.pptx

    Energy Savers [EERE]

    BSQ-300 Entire Selection Range BSQ-300 Allowable Selection Range: FER ≥ 1 BSQ-300 Allowable Speed Range: FER BEP ≥ 1 BSQ-300 CY2012 Actual Fan Selections (295) BSQ-300 Selections covered by size 360 BSQ-300 Selections covered by size 420

  1. Edgestar: ENERGY STAR Referral (DEP400EW)

    Office of Energy Efficiency and Renewable Energy (EERE)

    DOE referred the matter of Edgestar-brand dehumidifier, model DEP400EW, to the EPA for appropriate action after DOE testing showed that the model does not meet the ENERGY STAR specification.

  2. 500 kV Spare Transformer Procurement

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Procurement capital project is for the acquisition of five, 500 kV spare transformers, which are to be strategically located throughout the system, and for the...

  3. Crashworthiness of the AT-400A shipping container

    SciTech Connect (OSTI)

    Gruda, J.D.; York, A.R. II

    1996-05-01

    Shipping containers used for transporting radioactive material must be certified using federal regulations. These regulations require the container be tested or evaluated in severe mechanical and thermal environments which represent hypothetical accident scenarios. The containers are certified if the inner container remains leaktight. This paper presents results from finite element simulations of the accidents which include subjecting the AT-400A (for Pu from dismantled nuclear weapons) to a 30-foot (9 m) drop onto an unyielding target and crushing the container with an 1100 lb (500 kg) steel plate dropped from 30 feet. The nonlinear PRONTO3D finite element results were validated using test results. The simulations of the various impacts and crushes identified trends and worst-case orientations. They also showed that there is a significant margin of safety based on the failure of the containment vessel.

  4. Westinghouse Offers $6,400 in College Scholarships to Eddy County Students

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Offers $6,400 in College Scholarships to Eddy County Students CARLSBAD, N.M., February 18, 2000 - The Westinghouse Government Services Group today announced that $6,400 in college scholarships will be awarded to Eddy County students for the 2000-2001 school year. The deadline to apply is April 3. Two $2,500 scholarships are being offered - one will be honored at New Mexico State University (NMSU) in Las Cruces, and one at the College of the Southwest (CSW) in Carlsbad. High school seniors

  5. WIPP Receives 500th Waste Shipment

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    500 th Waste Shipment CARLSBAD, N.M., January 7, 2002 - The U.S. Department of Energy's (DOE) Waste Isolation Pilot Plant (WIPP) reached a new milestone Saturday with the safe arrival of its 500 th shipment of transuranic waste. The 500 th shipment arrived at WIPP at 6:38 p.m. Saturday from DOE's Rocky Flats Environmental Technology Site in Colorado. It was the 282 nd shipment to WIPP from Rocky Flats - one of five DOE sites sending defense-generated radioactive waste to WIPP for permanent

  6. Welding the AT-400A Containment Vessel

    SciTech Connect (OSTI)

    Brandon, E.

    1998-11-01

    Early in 1994, the Department of Energy assigned Sandia National Laboratories the responsibility for designing and providing the welding system for the girth weld for the AT-400A containment vessel. (The AT-400A container is employed for the shipment and long-term storage of the nuclear weapon pits being returned from the nation's nuclear arsenal.) Mason Hanger Corporation's Pantex Plant was chosen to be the production facility. The project was successfully completed by providing and implementing a turnkey welding system and qualified welding procedure at the Pantex Plant. The welding system was transferred to Pantex and a pilot lot of 20 AT-400A containers with W48 pits was welded in August 1997. This document is intended to bring together the AT-400A welding system and product (girth weld) requirements and the activities conducted to meet those requirements. This document alone is not a complete compilation of the welding development activities but is meant to be a summary to be used with the applicable references.

  7. The 16th P and GJ 500 report

    SciTech Connect (OSTI)

    Share, J.

    1996-09-01

    Pipeline and Gas Journal is pleased to present its 16th annual 500 Report--a comprehensive listing of the nation`s energy pipelines. The list comprises the leading 300 natural gas distribution utilities; top 100 gas transmission pipelines and top 100 liquids pipelines. The wealth of statistics includes pipeline mileage; total throughput of gas and barrels of crude oil and refined products; operating revenue; employees; and in the case of the gas distributors their number of customers. Just as important as the numbers are the trends they reveal of an energy industry continuing to undergo dramatic change. The gas industry in particular has faced a massive reorganization caused in large part by Federal Energy Regulatory Commission Order 636.

  8. The 17th annual P and GJ 500 report

    SciTech Connect (OSTI)

    Share, J.; Tubb, R.

    1997-11-01

    The staff of Pipeline and Gas Journal presents its 17th annual 500 Report, providing the industry`s most comprehensive statistical summary of the nation`s energy pipelines. The report was previously printed every September but has been moved to November to accommodate the new deadlines for pipeline companies to file their necessary paperwork with the Federal Energy Regulatory Commission. The report contains listings of the 300 leading natural gas distribution utilities; the top 100 transmission and gathering pipelines and the top 100 liquids pipelines. The distribution companies are ranked according to number of customers while gas pipelines are ranked by mileage. The liquids companies are determined by barrels. Other numbers include total throughput of natural gas and barrels of crude oil and refined products; operating revenue and net income; miles of mains and service lines, compression; and additions to plant.

  9. Building C-400 Thermal Treatment 90% Remedial Design Report and...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Building C-400 Thermal Treatment 90% Remedial Design Report and Site Investigation Building C-400 Thermal Treatment 90% Remedial Design Report and Site Investigation Full Document ...

  10. TOP500 Supercomputers for June 2002

    SciTech Connect (OSTI)

    Strohmaier, Erich; Meuer, Hans W.; Dongarra, Jack; Simon, Horst D.

    2002-06-20

    19th Edition of TOP500 List of World's Fastest Supercomputers Released MANNHEIM, Germany; KNOXVILLE, Tenn.;&BERKELEY, Calif. In what has become a much-anticipated event in the world of high-performance computing, the 19th edition of the TOP500 list of the worlds fastest supercomputers was released today (June 20, 2002). The recently installed Earth Simulator supercomputer at the Earth Simulator Center in Yokohama, Japan, is as expected the clear new number 1. Its performance of 35.86 Tflop/s (trillions of calculations per second) running the Linpack benchmark is almost five times higher than the performance of the now No.2 IBM ASCI White system at Lawrence Livermore National Laboratory (7.2 Tflop/s). This powerful leap frogging to the top by a system so much faster than the previous top system is unparalleled in the history of the TOP500.

  11. TOP500 Supercomputers for November 2003

    SciTech Connect (OSTI)

    Strohmaier, Erich; Meuer, Hans W.; Dongarra, Jack; Simon, Horst D.

    2003-11-16

    22nd Edition of TOP500 List of World s Fastest Supercomputers Released MANNHEIM, Germany; KNOXVILLE, Tenn.; BERKELEY, Calif. In what has become a much-anticipated event in the world of high-performance computing, the 22nd edition of the TOP500 list of the worlds fastest supercomputers was released today (November 16, 2003). The Earth Simulator supercomputer retains the number one position with its Linpack benchmark performance of 35.86 Tflop/s (''teraflops'' or trillions of calculations per second). It was built by NEC and installed last year at the Earth Simulator Center in Yokohama, Japan.

  12. OM300 Direction Drilling Module

    SciTech Connect (OSTI)

    MacGugan, Doug

    2013-08-22

    OM300 – Geothermal Direction Drilling Navigation Tool: Design and produce a prototype directional drilling navigation tool capable of high temperature operation in geothermal drilling Accuracies of 0.1° Inclination and Tool Face, 0.5° Azimuth Environmental Ruggedness typical of existing oil/gas drilling Multiple Selectable Sensor Ranges High accuracy for navigation, low bandwidth High G-range & bandwidth for Stick-Slip and Chirp detection Selectable serial data communications Reduce cost of drilling in high temperature Geothermal reservoirs Innovative aspects of project Honeywell MEMS* Vibrating Beam Accelerometers (VBA) APS Flux-gate Magnetometers Honeywell Silicon-On-Insulator (SOI) High-temperature electronics Rugged High-temperature capable package and assembly process

  13. Development of a 500 Watt High Temperature Thermoelectric Generator...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    a 500 Watt High Temperature Thermoelectric Generator Development of a 500 Watt High Temperature Thermoelectric Generator A low temperature TEG has been built and tested providing ...

  14. Klamath Residence (500) Space Heating Low Temperature Geothermal...

    Open Energy Info (EERE)

    Residence (500) Space Heating Low Temperature Geothermal Facility Jump to: navigation, search Name Klamath Residence (500) Space Heating Low Temperature Geothermal Facility...

  15. WAC 173-400 - General Regulations for Air Pollution Sources ...

    Open Energy Info (EERE)

    400 - General Regulations for Air Pollution Sources Jump to: navigation, search OpenEI Reference LibraryAdd to library Legal Document- RegulationRegulation: WAC 173-400 - General...

  16. WAC - 173-400 General Regulations for Air Pollution Sources ...

    Open Energy Info (EERE)

    400 General Regulations for Air Pollution Sources Jump to: navigation, search OpenEI Reference LibraryAdd to library Legal Document- RegulationRegulation: WAC - 173-400 General...

  17. TEAM CUMBERLAND Tennessee Valley Authority 400 West Summit Hill Drive, Knoxville, TN 37902

    Energy Savers [EERE]

    TEAM CUMBERLAND Tennessee Valley Authority 400 West Summit Hill Drive, Knoxville, TN 37902 March 24 & 25, 2015 On Tuesday, March 24 th , at 1:00 PM EST, in a conference room located TVA's West Tower, an analysis of Corps O&M expenditures will be discussed. At 3:00 PM EST, TVA will provide a tour of their River Scheduling Operations Center. Afterward, we'll meet in the Knoxville Marriott lobby at 6:15 PM EST and depart for Calhoun's for dinner (Dutch-treat). The meeting on Wednesday,

  18. Equation of State for Supercooled Water at Pressures up to 400 MPa

    SciTech Connect (OSTI)

    Holten, Vincent; Sengers, Jan V.; Anisimov, Mikhail A.

    2014-12-01

    An equation of state is presented for the thermodynamic properties of cold and supercooled water. It is valid for temperatures from the homogeneous ice nucleation temperature up to 300 K and for pressures up to 400 MPa, and can be extrapolated up to 1000 MPa. The equation of state is compared with experimental data for the density, expansion coefficient, isothermal compressibility, speed of sound, and heat capacity. Estimates for the accuracy of the equation are given. The melting curve of ice I is calculated from the phase-equilibrium condition between the proposed equation and an existing equation of state for ice I.

  19. ESnet, NERSC Blaze 400G Production Network Path

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    ESnet, NERSC Blaze 400G Production Network Path ESnet, NERSC Blaze 400G Production Network Path 400G Link is First Ever by R&E Network November 10, 2015 Contact: Jon Bashor, jbashor@lbl.gov, 510-486-5849 NetworkMapIllustration.png This map shows the 400G production link between Wang Hall at the main LBNL site and the Oakland Scientific Facility. The Department of Energy's Energy Sciences Network (ESnet) and the National Energy Research Scientific Computing Center (NERSC) have built a 400

  20. 300 Area Process Trenches Groundwater Monitoring Plan

    SciTech Connect (OSTI)

    Lindberg, Jonathan W.; Chou, Charissa J.

    2001-08-13

    This document is a proposed groundwater monitoring plan for the 300 Area process trenches to comply with RCRA final status, corrective action groundwater monitoring.

  1. President Obama Announces $400 Million Conditional Commitment Offer to

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Support Solar Panel Manufacturing | Department of Energy 400 Million Conditional Commitment Offer to Support Solar Panel Manufacturing President Obama Announces $400 Million Conditional Commitment Offer to Support Solar Panel Manufacturing July 3, 2010 - 12:00am Addthis Washington D.C. - In his weekly video address, President Obama today announced the offer of a conditional commitment for a loan guarantee of $400 million to Abound Solar Manufacturing, LLC to manufacture state-of-the-art

  2. Department of Energy Closes $400 Million Loan Guarantee for State...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    ... Related Articles President Obama Announces 400 Million Conditional Commitment Offer to Support Solar Panel Manufacturing Workers at Abound Solar -- who are about to get more than ...

  3. Application for Presidential Permit OE Docket No. PP-400 TDI...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Project - Comments and Motion to Intervene of Conservation Law Foundation Application for Presidential Permit OE Docket No. PP-400 TDI-NE - New England Clean Power Link Project - ...

  4. Application for Presidential Permit OE Docket No. PP-400 TDI...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Project: Motion to Intervene of The Northeast Power Coordinating Council, Inc. Application for Presidential Permit OE Docket No. PP-400 TDI-NE - New England Clean Power Link ...

  5. Hazardous waste operational plan for site 300

    SciTech Connect (OSTI)

    Roberts, R.S.

    1982-02-12

    This plan outlines the procedures and operations used at LLNL's Site 300 for the management of the hazardous waste generated. This waste consists primarily of depleted uranium (a by-product of U-235 enrichment), beryllium, small quantities of analytical chemicals, industrial type waste such as solvents, cleaning acids, photographic chemicals, etc., and explosives. This plan details the operations generating this waste, the proper handling of this material and the procedures used to treat or dispose of the hazardous waste. A considerable amount of information found in this plan was extracted from the Site 300 Safety and Operational Manual written by Site 300 Facility personnel and the Hazards Control Department.

  6. Monte Carlo evaluation of CTDI{sub {infinity}} in infinitely long cylinders of water, polyethylene and PMMA with diameters from 10 mm to 500 mm

    SciTech Connect (OSTI)

    Zhou Hong; Boone, John M.

    2008-06-15

    Monte Carlo simulations were used to evaluate the radiation dose to infinitely long cylinders of water, polyethylene, and poly(methylmethacrylate) (PMMA) from 10 to 500 mm in diameter. Radiation doses were computed by simulating a 10 mm divergent primary beam striking the cylinder at z=0, and the scattered radiation in the -z and +z directions was integrated out to infinity. Doses were assessed using the total energy deposited divided by the mass of the 10-mm-thick volume of material in the primary beam. This approach is consistent with the notion of the computed tomography dose index (CTDI) integrated over infinite z, which is equivalent to the dose near the center of an infinitely long CT scan. Monoenergetic x-ray beams were studied from 5 to 140 keV, allowing polyenergetic x-ray spectra to be evaluated using a weighted average. The radiation dose for a 10-mm-thick CT slice was assessed at the center, edge, and over the entire diameter of the phantom. The geometry of a commercial CT scanner was simulated, and the computed results were in good agreement with measured doses. The absorbed dose in water for 120 kVp x-ray spectrum with no bow tie filter for a 50 mm cylinder diameter was about 1.2 mGy per mGy air kerma at isocenter for both the peripheral and center regions, and dropped to 0.84 mGy/mGy for a 500-mm-diam water phantom at the periphery, where the corresponding value for the center location was 0.19 mGy/mGy. The influence of phantom composition was studied. For a diameter of 100 mm, the dose coefficients were 1.23 for water, 1.02 for PMMA, and 0.94 for polyethylene (at 120 kVp). For larger diameter phantoms, the order changed--for a 400 mm phantom, the dose coefficient of polyethylene (0.25) was greater than water (0.21) and PMMA (0.16). The influence of the head and body bow tie filters was also studied. For the peripheral location, the dose coefficients when no bow tie filter was used were high (e.g., for a water phantom at 120 kVp at a diameter of 300 mm, the dose coefficient was 0.97). The body bow tie filter reduces this value to 0.62, and the head bow tie filter (which is not actually designed to be used for a 300 mm object) reduces the dose coefficient to 0.42. The dose in CT is delivered both by the absorption of primary and scattered x-ray photons, and at the center of a water cylinder the ratio of scatter to primary (SPR) doses increased steadily with cylinder diameter. For water, a 120 kVp spectrum and a cylinder diameter of 200 mm, the SPR was 4, and this value grew to 9 for a diameter of 350 mm and to over 16 for a 500-mm-diam cylinder. A freely available spreadsheet was developed to allow the computation of radiation dose as a function of object diameter (10-500 mm), composition (water, polyethylene, PMMA), and beam energy (10-140 keV, 40-140 kVp)

  7. Super-Stable, Highly Monodisperse Plasmonic Nanocrystals with 500 Gold Atoms: Au~500(SR)~120

    SciTech Connect (OSTI)

    Kumara, Chanaka; Zuo, Xiaobing; Ilavsky, Dr. Jan; Chapman, Karena; Cullen, David A; Dass, Amala

    2014-01-01

    Determining the composition of plasmonic nanoparticles is challenging due to a deficiency in tools capable of accurately evaluating the number of atoms. Mass spectrometry plays a significant role in determining nanoparticle composition at the atomic level. Significant progress has been made in understanding ultra-small gold nanoparticles, like Au25(SR)18 and Au38(SR)24, with a Au core diameter of 0.97 and 1.3 nm, respectively. However, progress in small plasmonic nanoparticles (2 - 5 nm) is currently challenging, due in part to limitations in synthesizing monodisperse nanoparticles. Here, we report a plasmonic nanocrystal that is highly monodisperse, with an unprecedented variation of less than 20 gold atoms. The composition of the super-stable plasmonic nanocrystals at 115 kDa was determined to contain Au500 10SR120 3. The Au~500 system, named Faraduarate-500, is the largest size to be characterized using high resolution ESI mass spectrometry. Atomic pair distribution function (PDF) data shows that the local atomic structure is consistent with a face-centered cubic (fcc) or Marks decahedral arrangement. High resolution scanning transmission electron microscopy images show that the diameter is 2.4 0.1 nm. The radius of gyration measured by small angle X-ray scattering (SAXS), is 1.05 0.05 nm, and the size and the shape of SAXS molecular envelope are in agreement with TEM and PDF measurements.

  8. 300 area TEDF permit compliance monitoring plan

    SciTech Connect (OSTI)

    BERNESKI, L.D.

    1998-11-20

    This document presents the permit compliance monitoring plan for the 300 Area Treated Effluent Disposal Facility (TEDF). It addresses the compliance with the National Pollutant Discharge Elimination System (NPDES) permit and Department of Natural Resources Aquatic Lands Sewer Outfall Lease.

  9. Improvement of voltage holding capability in the 500 keV negative ion source for JT-60SA

    SciTech Connect (OSTI)

    Tanaka, Y.; Hanada, M.; Kojima, A.; Akino, N.; Shimizu, T.; Ohshima, K.; Inoue, T.; Watanabe, K.; Taniguchi, M.; Kashiwagi, M.; Umeda, N.; Tobari, H.; Grisham, L. R.; Collaboration: JT-60 NBI Group

    2010-02-15

    Voltage holding capability of JT-60 negative ion source that has a large electrostatic negative ion accelerator with 45 cmx1.1 m acceleration grids was experimentally examined and improved to realize 500 keV, 22 A, and 100 s D{sup -} ion beams for JT-60 Super Advanced. The gap lengths in the acceleration stages were extended to reduce electric fields in a gap between the large grids and at the corner of the support flanges from the original 4-5 to 3-4 kV/mm. As a result, the voltage holding capability without beam acceleration has been successfully improved from 400 to 500 kV. The pulse duration to hold 500 kV reached 40 s of the power supply limitation.

  10. ESnet, NERSC Blaze 400G Production Network Path

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    to act as a single 400 Gbps optical transport connection between the two sites. A History of Strong Connections The user facilities known today as NERSC and ESnet both date...

  11. Conceptual designs for the AT-400MO package

    SciTech Connect (OSTI)

    Fischer, L.E.; Hafner, R.F.; Hovingh, J.; Keeton, S.C.; Russell, E.W.; Lemmings, J.

    1997-01-01

    Currently, Pantex handles and stores weapons pits in AT-400A packages. The Department of Energy currently plans to oversee the conversion of weapon pits into plutonium metal or oxide. These products will then be stored, and perhaps transported at a later time, to other DOE sites. If DOE assigns the pit conversion process to Pantex, it makes sense to store the resulting Pu metal or oxide at Pantex, utilizing existing facilities, equipment, processes, and personnel. The four conceptual designs presented herein substitute the current AT-400A containment vessel, designed for weapon pits, with a vessel designed to store and/or ship Pu metal or oxides. These new designs utilize the existing AT-400A overpack system consisting of the drum assembly and radial impact limiters and likewise employ existing AT-400A production operations.

  12. 400 Area/Fast Flux Test Facility - Hanford Site

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    325 Building 400 AreaFast Flux Test Facility 618-10 ... Test Facility D and DR Reactors Effluent Treatment ... (thermal) liquid-metal (sodium)-cooled nuclear research ...

  13. Application for Presidential Permit OE Docket No. PP-400 TDI...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    NE New England Clean Power Link Project Application for Presidential Permit OE Docket No. PP-400 TDI- NE New England Clean Power Link Project Response to TDI - NE application from ...

  14. Application for Presidential Permit OE Docket No. PP-400 TDI...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    New England - New England Clean Power Link Project Application for Presidential Permit OE Docket No. PP-400 TDI-New England - New England Clean Power Link Project Application from ...

  15. Application for Presidential Permit OE Docket No. PP-400 TDI...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    New England Clean Power Link Project Application for Presidential Permit OE Docket No. PP-400 TDI-NE New England Clean Power Link Project Response for TDI-NE from Department of ...

  16. Application for Presidential Permit OE Docket No. PP-400 TDI...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    - New England Clean Power Link Project: Federal Register Notice, Volume 79, No. 131 - July 9, 2014 Application for Presidential Permit OE Docket No. PP-400 TDI-NE - New England ...

  17. Summary - Building C-400 Thermal Treatment Remedial Design Report...

    Office of Environmental Management (EM)

    Paducah, KY EM Project: Building C400 Thermal Treatment ETR Report Date: August 2007 ETR-8 United States Department of Energy Office of Environmental Management (DOE-EM) External...

  18. Sequoia ranked third in TOP500 list | National Nuclear Security...

    National Nuclear Security Administration (NNSA)

    according to the industry-standard Top500 list. Sequoia, which recently completed its transition to classified computing in support of NNSA's Stockpile Stewardship Program,...

  19. Comparative study of the embrittlement of Monel 400 at room temperature by hydrogen and by mercury

    SciTech Connect (OSTI)

    Price, C.E.; Fredell, R.S.

    1986-05-01

    Slow strain rate tensile tests were performed at room temperature on Monel 400 specimens of grain sizes 35 to 500 microns, in the environments of air, mercury, and electrolytically generated hydrogen. Specimens of grain size 250 microns were tested at a range of strain rates in the three environments. It was found that cracks initiated easiest in hydrogen but propagated easiest in mercury; consequently the embrittlement was usually more severe in mercury. The embrittlement decreased with increasing strain rate, and with increasing grain size in hydrogen. Embrittlement in mercury was maximum at intermediate grain sizes. A fracture sequence of intergranular to transgranular to microvoid coalescence was common. The intergranular and transgranular fractures are interpreted in terms of the reduced cohesive stress and enhanced shear models of embrittlement, respectively. 52 references.

  20. Reno-Moana Area (300) Space Heating Low Temperature Geothermal...

    Open Energy Info (EERE)

    Reno-Moana Area (300) Space Heating Low Temperature Geothermal Facility Jump to: navigation, search Name Reno-Moana Area (300) Space Heating Low Temperature Geothermal Facility...

  1. Engineering Study of 500 ML Sample Bottle Transportation Methods

    SciTech Connect (OSTI)

    BOGER, R.M.

    1999-08-25

    This engineering study reviews and evaluates all available methods for transportation of 500-mL grab sample bottles, reviews and evaluates transportation requirements and schedules and analyzes and recommends the most cost-effective method for transporting 500-mL grab sample bottles.

  2. High-Definition Differential Ion Mobility Spectrometry with Resolving Power up to 500

    SciTech Connect (OSTI)

    Shvartsburg, Alexandre A.; Seim, Thomas A.; Danielson, William F.; Norheim, Randolph V.; Moore, Ronald J.; Anderson, Gordon A.; Smith, Richard D.

    2013-01-20

    As the resolution of analytical methods improve, further progress tends to be increasingly limited by instrumental parameter instabilities that could be ignored before. This is now the case with differential ion mobility spectrometry (FAIMS), where fluctuations of the voltages and gas pressure have become critical. A new high-definition generator for FAIMS compensation voltage reported here provides a stable and accurate output than can be scanned with negligible steps. This reduces the spectral drift and peak width, thus improving the resolving power (R) and resolution. The gain for multiply-charged peptides that have narrowest peaks is up to ~40%, and R ~ 400 - 500 is achievable using He/N2 or H2/N2 gas mixtures.

  3. Obama Administration Announces Additional $9,593,500 for Local...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    the District of Columbia Obama Administration Announces Additional 9,593,500 for Local Energy Efficiency Improvements in the District of Columbia March 26, 2009 - 12:00am Addthis...

  4. Labor Department Offers $500 Million for Clean Energy Job Training

    Office of Energy Efficiency and Renewable Energy (EERE)

    The U.S. Department of Labor recently launched five grant competitions, totaling $500 million, to fund projects that prepare workers for green jobs in the energy efficiency and renewable energy industries.

  5. Northern New Mexico students receive $419,500 in scholarships

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Northern New Mexico students receive $419,500 in scholarships Community Connections: Your link to news and opportunities from Los Alamos National Laboratory Latest Issue:May 2016 all issues All Issues » submit Northern New Mexico students receive $419,500 in scholarships Awards go to seven northern New Mexico counties May 5, 2014 Bernalillo High School senior Raymond Fasano is LAESF's 2014 Platinum Scholarship recipient. Bernalillo High School senior Raymond Fasano is LAESF's 2014 Platinum

  6. NREL's Clean Energy Forum Attracts Nearly 500 Participants from Investment

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Community - News Releases | NREL NREL's Clean Energy Forum Attracts Nearly 500 Participants from Investment Community Three Clean Energy Companies Honored at Awards Event October 21, 2010 The U.S. Department of Energy's National Renewable Energy Laboratory (NREL) 23rd Industry Growth Forum this week attracted nearly 500 investors, entrepreneurs, scientists and policymakers to Denver. The three-day forum highlighted clean energy industry technology and business developments. NREL also hosted

  7. Sequoia supercomputer tops Graph 500 | National Nuclear Security

    National Nuclear Security Administration (NNSA)

    Administration Sequoia supercomputer tops Graph 500 Wednesday, November 19, 2014 - 11:34am Lawrence Livermore National Laboratory scientists' search for new ways to solve large complex national security problems led to the top ranking on Graph 500 and new techniques for solving large graph problems on small high performance computing (HPC) systems, all the way down to a single server. Lawrence Livermore's Sequoia supercomputer, a 20-petaflop IBM Blue Gene/Q system, achieved the world's best

  8. Golden Eagle Territories and Ecology at Site 300

    SciTech Connect (OSTI)

    Fratanduono, M.

    2015-09-29

    Garcia and Associates (GANDA) was contracted by the Lawrence Livermore National Laboratory (LLNL) to collect information on golden eagle (Aquila chrysaetos) use of Site 300. During 2014, we conducted surveys at Site 300 and for an area including a 10-mile radius of Site 300. Those surveys documented 42 golden eagle territories including two territories that overlapped with Site 300. These were named ‘Tesla’ and ‘Linac Road’. In 2015, we conducted surveys to refine the territory boundaries of golden eagle territories that overlapped with Site 300 and to document eagle activity at Site 300.

  9. The 300 mA SRF ERL

    SciTech Connect (OSTI)

    Ben-Zvi, Ilan

    2013-11-07

    Energy Recovery Linacs (ERL) are important for a variety of applications, from high-power Free-Electron Lasers (FEL) to polarized-electron polarized-proton colliders. The ERL current is arguably the most important characteristic of ERLs for such applications. With that in mind, the Collider-Accelerator Department at Brookhaven National Laboratory embarked on the development of a 300 mA ERL to serve as an R and D test-bed for high-current ERL technologies. These include high-current, extremely well damped superconducting accelerating cavities, high-current superconducting laser-photocathode electron guns and high quantum-efficiency photocathodes. In this presentation I will cover these ERL related developments.

  10. Heat-source specification 500 watt(e) RTG

    SciTech Connect (OSTI)

    Not Available

    1983-02-01

    This specification establishes the requirements for a /sup 90/SrF/sub 2/ heat source and its fuel capsule for application in a 500 W(e) thermoelectric generator. The specification covers: fuel composition and quantity; the Hastelloy S fuel capsule material and fabrication; and the quality assurance requirements for the assembled heat source. (LCL)

  11. History of the ZGS 500 MeV booster.

    SciTech Connect (OSTI)

    Simpson, J.; Martin; R.; Kustom, R.

    2006-05-09

    The history of the design and construction of the Argonne 500 MeV booster proton synchrotron from 1969 to 1982 is described. This accelerator has since been in steady use for the past 25 years to power the Argonne Intense Pulsed Neutron Source (IPNS).

  12. Development of a 500 Watt High Temperature Thermoelectric Generator |

    Broader source: Energy.gov (indexed) [DOE]

    Department of Energy A low temperature TEG has been built and tested providing over 500 watts electric power at a ∆T of 2000C PDF icon deer09_lagrandeur.pdf More Documents & Publications Development of a 100-Watt High Temperature Thermoelectric Generator Automotive Waste Heat Conversion to Power Program Automotive Waste Heat Conversion to Power Program

  13. Neutron diffraction measurements of intergranular strains in MONEL-400

    SciTech Connect (OSTI)

    Holden, T.M.; Holt, R.A.; Clarke, A.P.

    1997-12-01

    Measurements have been made of the strain response parallel and perpendicular to an applied stress in uniaxial tensile specimens of MONEL-400. The diffraction elastic constants are in close agreement with the Kroener model. Beyond the yield point, different crystallographic orientations respond quite differently to the applied stress and, upon unloading, residual intergranular strains are generated which are tensile for some orientations and compressive for others. A simple theory based on the Taylor-Bishop-Hill (TBH) model gives a good qualitative description of the effects.

  14. Alloy 400 tube failures by stress corrosion cracking

    SciTech Connect (OSTI)

    Amar, A.S.

    1995-12-01

    A feedwater heater with SB163 Alloy 400 (cold drawn - stress relieved) tubing experienced numerous tube failures and was replaced after of 4.5 years. Failures were attributed to Inter Granular Stress Corrosion Cracking (IGSCC) in the roll transition area. An eddy current test method was developed with EPRI NDE Center technical support to detect the cracks in the tubesheet region. Three tubes were pulled for metallurgical examination. Short axial cracks were found on tube inner surface. Measured crack depths were correlated with the eddy current indications. A large number of tubes were plugged. However, the heater continued to deteriorate rapidly. Potential contributors to IGSCC are discussed.

  15. Upgrading the Linac 400 MeV Switchyard

    SciTech Connect (OSTI)

    Charles M Ankenbrandt et al.

    2004-06-09

    This note describes changes in the 400 MeV beam transfer system from the Linac to improve the quality of the beam delivered to the Booster and to add the capability to direct beam to the MuCool Test Area (MTA). The new configuration has two pairs of pulsed dipole magnets on each side of the 400 MeV electrostatic Chopper. The smaller pair deflects vertically to replace the kick of the Chopper to send the beam to the Booster while the larger pair deflects horizontally to transfer the beam to the MTA. In this new scheme, the Chopper is uncharged while the beam is injected into the Booster such that the injection position does not rely on Chopper power supply regulation as it does now. A feature of the proposed upgrade is that no changes in the lattice functions are required in the lines to the Booster or to the Dump; once the four new magnets are installed, the switch between the old and new operating modes can be done from upstairs. The transfer to the MTA is already described in a previous note.

  16. The 15th P and GJ 500 Report

    SciTech Connect (OSTI)

    Congram, G.E.

    1995-09-01

    This is an annual compilation of data on the pipeline industry of the US. It provides information on the gas utilities and oil and gas transmission. Data is broken out by companies in terms of mileage, deliveries, operating revenues, operation additions, and numbers of customers. It is separated into both gas and liquids according to the top 10 and the top 300 distribution companies. It also provides a company break-out based on the top 100 gas and liquids pipelines.

  17. Top 500 List Recognizes Fastest Supercomputers | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    00 List Recognizes Fastest Supercomputers Top 500 List Recognizes Fastest Supercomputers June 30, 2014 - 5:25pm Addthis Titan 1 of 4 Titan Oak Ridge National Laboratory's Titan has a theoretical peak performance of more than 27 petaflops, or more than 27 quadrillion calculations per second. This enables researchers across the scientific arena, from materials to climate change to astrophysics, to acquire unparalleled accuracy in their simulations and achieve research breakthroughs more rapidly

  18. Residual Oxygen on Nb Heated to 500 C

    SciTech Connect (OSTI)

    Kirby, R.; King, F.K.; Padamsee, H.; /Cornell U., LEPP

    2005-06-10

    The superconducting accelerating cavities for the International Linear Collider will be constructed of high-residual resistivity ratio (RRR) niobium sheet. Excessive oxygen within the skin depth (several microns) will reduce the RRR and increase resistive losses. We measure the thickness of this oxide layer, following bakeout simulation, to be about 0.5 nm thick. The results suggest that this layer will very slowly disappear from the top five nm at 500 C.

  19. PG&E Plans for 500 MW of PV

    Broader source: Energy.gov [DOE]

    PG&E has developed a plan to install 500 MW of PV by the year 2015. The plan calls for 250 MW to be acquired through Power Purchase Agreements (PPA) and the other 250 MW to be purchased and owned by the utility. PG&E presented the plan at a public forum on April 27, 2009. A copy of the power point presentation is attached.

  20. Firm turns trash to steam, saves $60,500

    SciTech Connect (OSTI)

    Cohn, L.

    1982-05-17

    An incinerator/boiler system that the Ingersoll-Rand Co. uses to burn trash and produce steam for heating and parts cleaning saved the company $60,500 in avoided fuel and trash-disposal costs last year. Replacing a natural gas-fired boiler, the new system reduces the demand for gas by 14%. Heat recovered from the trash burning is transferred to the boiler to make steam. No smoke is emitted. (DCK)

  1. Investigating the presence of 500 μm submillimeter excess emission...

    Office of Scientific and Technical Information (OSTI)

    Investigating the presence of 500 m submillimeter excess emission in local star forming galaxies Citation Details In-Document Search Title: Investigating the presence of 500 m ...

  2. Spitzer IRAC mid-infrared photometry of 500-750 brown dwarf

    SciTech Connect (OSTI)

    Saumon, Didier; Leggett, Sandy K; Albert, Loic; Artigau, Etienne; Burningham, Ben; Delfosse, Xavier; Delorme, Philippe; Forveille, Thierry; Lucas, Philip W; Marley, Mark S; Pinfield, David J; Reyle, Celine; Smart, Richard L; Warren, Stephen J

    2010-10-26

    Mid-infrared data, including Spitzer warm-IRAC [3.6] and [4.5] photometry, is critical for understanding the cold population of brown dwarfs now being found, objects which have more in common with planets than stars. As effective temperature (T{sub eff}) drops from 800K to 400K, the fraction of flux emitted beyond 3 {mu}m increases rapidly, from about 40% to > 75%. This rapid increase makes a color like H-[4.5] a very sensitive temperature indicator, and it can be combined with a gravity- and metallicity-sensitive color like H-K to constrain all three of these fundamental properties, which in turn gives us mass and age for these slowly cooling objects. Determination of mid-infrared color trends also allows better exploitation of the WISE mission by the community. We use new Spitzer Cycle 6 IRAC photometry, together with published data, to present trends of color with type for L0 to T10 dwarfs. We also use the atmospheric and evolutionary models of Saumon and Marley to investigate the masses and ages of 13 very late-type T dwarfs, which have H-[4.5] > 3.2 and T{sub eff} {approx} 500K to 750K.

  3. INVESTIGATION IN HARDSURFACING A NICKEL-COPPER ALLOY (MONEL400).

    SciTech Connect (OSTI)

    CZAJKOWSKI,C.; BUTTERS,M.

    2001-12-01

    Brookhaven National Laboratory (BNL) investigated the causes of weldability problems and materials failures encountered with the application of Monel (Ni-Cu) 400 as a base material and Stellite 6 (Co-Cr) as the hard-surfacing material when using the oxyacetylene welding process. This work was performed under a cooperative research and development agreement (CRADA) with the Target Rock Division of the Curtiss-Wright Flow Control Corporation. BNL evaluated two heats of Monel 400 material. One of the heats had performed well during manufacturing, producing an acceptable number of ''good'' parts. The second heat had produced some good parts but also exhibited a peculiar type of hardsurfacing/base metal collapse during the welding process. A review of the chemistry on the two heats of material indicated that they both met the chemical requirements for Monel400. During examination of the failed component, linear indications (cracks) were evident on the valve body, both on the circumferential area (top of valve body) and below the hard surfaced weld deposit. independent measurements also indicated that the two heats met the specification requirement for the material. The heat affected zone (HAZ) also contained linear discontinuities. The valve body was welded using the oxyacetylene welding process, a qualified and skilled welder, and had been given a pre-heat of between 1400-1600 F (760-871 C), which is the Target Rock qualified procedure requirement. Both original suppliers performed mechanical testing on their material that indicated the two heats also met the mechanical property requirements of the specification. The BNL investigation into the cause of the differences between these heats of material utilized the following techniques: (1) Heat Treatment of both heats of material; (2) Hardness testing; (3) Optical microscopy; (4) Scanning electron microscope (SEM)/Fractography; and (5) Energy dispersive spectroscopy (EDS). The report concludes that the cause of the failure of the valve body during welding is not obvious, however, it does not appear to be a welding issue. The observed inter-granular fractures indicate a grain boundary problem. Further research is recommended.

  4. Hanford Site - 300-FF-3 | Department of Energy

    Office of Environmental Management (EM)

    300-FF-3 Hanford Site - 300-FF-3 July 1, 2014 - 12:00pm Addthis US Department of Energy Groundwater Database Groundwater Master Report InstallationName, State: Hanford, WA Responsible DOE Office: Office of Environmental Management Plume Name: 300-FF-3 Remediation Contractor: CHPRC PBS Number: 30 Report Last Updated: July 2014 with CY2013 data Contaminants Halogenated VOCs/SVOCs Present?: Yes VOC Name Concentration (ppb) Regulatory Driver Cleanup Requirement DCE 220 Yes 16 (CUL) TCE 430 Yes 4

  5. Application for presidential permit OE Docket No. PP-300 Maine...

    Energy Savers [EERE]

    0 Maine Public Service Company Application for presidential permit OE Docket No. PP-300 Maine Public Service Company Applicationfrom Maine Public Service Company to construct, ...

  6. High Temperature 300°C Directional Drilling System

    Broader source: Energy.gov [DOE]

    Project objective: provide a directional drilling system that can be used at environmental temperatures of up to 300°C; and at depths of 10; 000 meters.

  7. OM300-GeoThermal MWD Navigation Instrument

    Broader source: Energy.gov [DOE]

    Develop a 300°C capable directional drilling navigation tool using Micro Electro-Mechanical Systems (MEMS) accelerometers and flux-gate magnetometers.

  8. Characterization of Field Experimental Sites at Hanford's 300...

    Office of Scientific and Technical Information (OSTI)

    Characterization of Field Experimental Sites at Hanford's 300-Area IFC Site Citation Details In-Document Search Title: Characterization of Field Experimental Sites at Hanford's ...

  9. Oregon - ORS 439.300 - Definitions | Open Energy Information

    Open Energy Info (EERE)

    Oregon, 2014 DOI Not Provided Check for DOI availability: http:crossref.org Online Internet link for Oregon - ORS 439.300 - Definitions Citation Oregon. 2014. Oregon - ORS...

  10. With 400th Ph.D. grad, UW-Madison celebrates a half century of...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    With 400th Ph.D. grad, UW-Madison celebrates a half century of fusion energy American Fusion News Category: U.S. Universities Link: With 400th Ph.D. grad, UW-Madison celebrates a...

  11. Fabrication and Measurements of 500 MHz Double Spoke Cavity

    SciTech Connect (OSTI)

    Park, HyeKyoung; Hopper, Christopher S.; Delayen, Jean R.

    2014-12-01

    A 500 MHz β0=1 double spoke cavity has been designed and optimized for a high velocity application such as a compact electron accelerator at the Center for Accelerator Science at Old Dominion University [1] and the fabrication was recently completed at Jefferson Lab. The geometry specific to the double spoke cavity required a variety of tooling and fixtures. Also a number of asymmetric weld joints were expected to make it difficult to maintain minimal geometric deviation from the design. This paper will report the fabrication procedure, resulting tolerance from the design, initial test results and the lessons learned from the first β0=1 double spoke cavity fabrication.

  12. Identification of 300 Area Contaminants of Potential Concern for Soil

    SciTech Connect (OSTI)

    R.W. Ovink

    2010-04-05

    This report documents the process used to identify source area contaminants of potential concern (COPCs) in support of the 300 Area remedial investigation/feasibility study (RI/FS) work plan. This report also establishes the exclusion criteria applicable for 300 Area use and the analytical methods needed to analyze the COPCs.

  13. Development of Electrolytes for Lithium-ion Batteries

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    ... Electrochemical Impedance Spectroscopy 0 100 200 300 400 500 0 50 100 150 200 250 Std ... of silicon anodes is a significant challenge * Generating a better understanding of ...

  14. Revised ground-water monitoring compliance plan for the 300 area process trenches

    SciTech Connect (OSTI)

    Schalla, R.; Aaberg, R.L.; Bates, D.J.; Carlile, J.V.M.; Freshley, M.D.; Liikala, T.L.; Mitchell, P.J.; Olsen, K.B.; Rieger, J.T.

    1988-09-01

    This document contains ground-water monitoring plans for process-water disposal trenches located on the Hanford Site. These trenches, designated the 300 Area Process Trenches, have been used since 1973 for disposal of water that contains small quantities of both chemicals and radionuclides. The ground-water monitoring plans contained herein represent revision and expansion of an effort initiated in June 1985. At that time, a facility-specific monitoring program was implemented at the 300 Area Process Trenches as part of a regulatory compliance effort for hazardous chemicals being conducted on the Hanford Site. This monitoring program was based on the ground-water monitoring requirements for interim-status facilities, which are those facilities that do not yet have final permits, but are authorized to continue interim operations while engaged in the permitting process. The applicable monitoring requirements are described in the Resource Conservation and Recovery Act (RCRA), 40 CFR 265.90 of the federal regulations, and in WAC 173-303-400 of Washington State's regulations (Washington State Department of Ecology 1986). The program implemented for the process trenches was designed to be an alternate program, which is required instead of the standard detection program when a facility is known or suspected to have contaminated the ground water in the uppermost aquifer. The plans for the program, contained in a document prepared by the US Department of Energy (USDOE) in 1985, called for monthly sampling of 14 of the 37 existing monitoring wells at the 300 Area plus the installation and sampling of 2 new wells. 27 refs., 25 figs., 15 tabs.

  15. Nondestructive Testing Qualification of Main Circulatory Tube Pipes DU 500

    SciTech Connect (OSTI)

    Tabakova, Bojana M.; Tzokov, Petio

    2004-07-01

    The criteria for safe operation of nuclear energetic installations is given a higher priority in the policy of Kozloduy Nuclear Power Plant. An efficient non-destructive inspection is the key point for the safe service. Kozloduy NPP keeps on making investments in equipment and qualification of specialists in this field. The processes of qualification of the NDT components, important for the nuclear and radiation safety, make considerable improvement in Kozloduy NPP, thanks to the accumulated in the years experience in the activities of NDT inspection qualification, and to the help of our partners Serco Assurance and the Institute of Rzes. The results obtained by ultrasonic non-destructive inspection of circulation tube mains DU 500 WWER 440 type are under discussion in this report. (authors)

  16. The 18. annual P and GJ 500 Report

    SciTech Connect (OSTI)

    Share, J.; Tubb, R.

    1998-11-01

    The staff of Pipeline and Gas Journal presents its 18th annual 500 Report, providing the industry`s most comprehensive summary of the nation`s energy pipeline systems. As usual, categories are broken down to include the top liquids pipelines, gas transmission and distribution systems. The transmission companies are ranked by mileage while the liquids companies are determined by numbers of barrels. The gas distribution rankings are determined by number of customers. Other numbers include total throughput of natural gas and barrels of crude oil and refined products; operating revenue and net income; miles of mains and service lines; compression; and additions to plant. The figures for the most part represent calendar year 1997 statistics as compared to 1996. One interesting note: the mild winter of 1997--98 throughout most of the East Coast and Midwest led to a decrease in volume, especially for natural gas, and a resulting decline in revenues for a substantial number of companies.

  17. 500-kW DCHX pilot-plant evaluation testing

    SciTech Connect (OSTI)

    Hlinak, A.; Lee, T.; Loback, J.; Nichols, K.; Olander, R.; Oshmyansky, S.; Roberts, G.; Werner, D.

    1981-10-01

    Field tests with the 500 kW Direct Contact Pilot Plant were conducted utilizing brine from well Mesa 6-2. The tests were intended to develop comprehensive performance data, design criteria, and economic factors for the direct contact power plant. The tests were conducted in two phases. The first test phase was to determine specific component performance of the DCHX, turbine, condensers and pumps, and to evaluate chemical mass balances of non-condensible gases in the IC/sub 4/ loop and IC/sub 4/ in the brine stream. The second test phase was to provide a longer term run at nearly fixed operating conditions in order to evaluate plant performance and identify operating cost data for the pilot plant. During these tests the total accumulated run time on major system components exceeded 1180 hours with 777 hours on the turbine prime mover. Direct contact heat exchanger performance exceeded the design prediction.

  18. 300 Area Record of Decision Issued - Hanford Site

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    300 Area Record of Decision Issued 300 Area Record of Decision Issued 300 Area Record of Decision Issued Email Email Page | Print Print Page |Text Increase Font Size Decrease Font Size TPA Logo The Tri-Party Agreement (TPA) agencies - the U.S. Department of Energy (DOE), the U.S. Environmental Protection Agency (EPA), and the Washington State Department of Ecology (Ecology) - have issued a Record of Decision (ROD) for cleanup of contaminated soil and groundwater along the Columbia River in the

  19. Observation of 23 supernovae that exploded <300 pc from Earth during the past 300 kyr

    SciTech Connect (OSTI)

    Firestone, R. B.

    2014-07-01

    Four supernovae (SNe), exploding ≤300 pc from Earth, were recorded 44, 37, 32, and 22 kyr ago in the radiocarbon ({sup 14}C) record during the past 50 kyr. Each SN left a nearly identical signature in the record, beginning with an initial sudden increase in atmospheric radiocarbon, when the SN exploded, followed by a hiatus of 1500 yr, and concluding with a sustained 2000 yr increase in global radiocarbon due to γ-rays produced by diffusive shock in the SN remnant (SNR). For the past 18 kyr excess radiocarbon has decayed with the {sup 14}C half-life. SN22kyrBP, is identified as the Vela SN that exploded 250 ± 30 pc from Earth. These SN are confirmed in the {sup 10}Be, {sup 26}Al, {sup 36}Cl, and NO{sub 3}{sup −} geologic records. The rate of near-Earth SNe is consistent with the observed rate of historical SNe giving a galactic rate of 14 ± 3 kyr{sup –1} assuming the Chandra Galactic Catalog SNR distribution. The Earth has been used as a calorimeter to determine that ≈2 × 10{sup 49} erg were released as γ-rays at the time of each SN explosion and ≈10{sup 50} erg in γ-rays following each SN. The background rate of {sup 14}C production by cosmic rays has been determined as 1.61 atoms cm{sup –2} s{sup –1}. Approximately 1/3 of the cosmic ray energy produced by diffusive shock in the SNR was observed to be emitted as high-energy γ-rays. Analysis of the {sup 10}Be/{sup 9}Be ratio in marine sediment identified 19 additional near-Earth SNe that exploded 50-300 kyr ago. Comparison of the radiocarbon record with global temperature variations indicated that each SN explosion is correlated with a concurrent global warming of ≈3°C-4°C.

  20. 300 Area Remedial Investigation/Feasibility Study and Proposed...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    S. Hudson Page 1 of 2 300 Area Remedial InvestigationFeasibility Study and Proposed Plan Deconstruct Advice Points (paragraph number ) 4-1 The Board believes the Tri-Party...

  1. Innovative Cell Materials and Designs for 300 Mile Range EVs

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Innovative Cell Materials and Design for 300 Mile Range EVs Yimin Zhu, PDPI OneD Material, LLC (former Nanosys Energy Storage) Palo Alto, California June 16 20, 2014 DOE Vehicle ...

  2. 300 Area waste acid treatment system closure plan. Revision 1

    SciTech Connect (OSTI)

    1996-03-01

    This section provides a description of the Hanford Site, identifies the proposed method of 300 Area Waste Acid Treatment System (WATS) closure, and briefly summarizes the contents of each chapter of this plan.

  3. The Breakthrough Behind a 300% Increase in Photosynthesis Productivity |

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Department of Energy The Breakthrough Behind a 300% Increase in Photosynthesis Productivity The Breakthrough Behind a 300% Increase in Photosynthesis Productivity January 31, 2011 - 3:29pm Addthis Sunita Satyapal Director, Fuel Cell Technologies Office What does this mean for me? Could lead to cheaper renewable energy sources. Recently, the Department of Energy hosted Dr. Tasios Melis, the UC Berkeley scientist behind a Department of Energy funded innovation that promises to triple the

  4. Secretary Chu Announces Nearly $300 Million Rebate Program to Encourage

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Purchases of Energy Efficient Appliances | Department of Energy Rebate Program to Encourage Purchases of Energy Efficient Appliances Secretary Chu Announces Nearly $300 Million Rebate Program to Encourage Purchases of Energy Efficient Appliances July 14, 2009 - 12:00am Addthis WASHINGTON, DC - U.S. Department of Energy Secretary Steven Chu today announced the availability of nearly $300 million in funding from the American Recovery and Reinvestment Act for state-run rebate programs for

  5. A lead-before-break strategy for primary heat transport piping of 500 MWe Indian PHWR

    SciTech Connect (OSTI)

    Chattopadhyay, J.; Dutta, B.K.; Kushwaha, H.S.

    1997-04-01

    Leak-Before-Break (LBB) is being used to design the primary heat transport piping system of 500 MWe Indian Pressurized Heavy Water Reactors (IPHWR). The work is categorized in three directions to demonstrate three levels of safety against sudden catastrophic break. Level 1 is inherent in the design procedure of piping system as per ASME Sec.III with a well defined factor of safety. Level 2 consists of fatigue crack growth study of a postulated part-through flaw at the inside surface of pipes. Level 3 is stability analysis of a postulated leakage size flaw under the maximum credible loading condition. Developmental work related to demonstration of level 2 and level 3 confidence is described in this paper. In a case study on fatigue crack growth on PHT straight pipes for level 2, negligible crack growth is predicted for the life of the reactor. For level 3 analysis, the R6 method has been adopted. A database to evaluate SIF of elbows with throughwall flaws under combined internal pressure and bending moment has been generated to provide one of the inputs for R6 method. The methodology of safety assessment of elbow using R6 method has been demonstrated for a typical pump discharge elbow. In this analysis, limit load of the cracked elbow has been determined by carrying out elasto-plastic finite element analysis. The limit load results compared well with those given by Miller. However, it requires further study to give a general form of limit load solution. On the experimental front, a set of small diameter pipe fracture experiments have been carried out at room temperature and 300{degrees}C. Two important observations of the experiments are - appreciable drop in maximum load at 300{degrees}C in case of SS pipes and out-of-plane crack growth in case of CS pipes. Experimental load deflection curves are finally compared with five J-estimation schemes predictions. A material database of PHT piping materials is also being generated for use in LBB analysis.

  6. Deployment of GTHTR300 Cogeneration for Hydrogen and Electric Generation

    SciTech Connect (OSTI)

    Kazuhiko Kunitomi; Xing Yan; Isao Minatsuki

    2004-07-01

    JAERI (Japan Atomic Energy Research Institute) has started the design study on the GTHTR300-cogeneration (GTHTR300C) aiming at producing electricity by a helium gas turbine and hydrogen by a thermochemical water splitting method (IS process method). The GTHTR300C is a block type High Temperature Gas-cooled Reactor (HTGR) with its reactor thermal power of 600 MW and outlet coolant temperature of 950 deg. C. The Intermediate Heat Exchanger (IHX) is located between the reactor pressure vessel (RPV) and the gas turbine system. The heat capacity of the IHX is 170 MW and is used for hydrogen production. The balance of the reactor thermal power is used for electric generation. The GTHTR300C is designed based on existing technologies for the High Temperature Engineering Test Reactor (HTTR) and the helium turbine power conversion technology under development for the Gas Turbine High Temperature Reactor (GTHTR300). This paper describes the deployment of the GTHTR300C together with the original design features and advantages of the system. (authors)

  7. Successful continuous injection of coal into gasification and PFBC system operating pressures exceeding 500 PSI - DOE funded program results

    SciTech Connect (OSTI)

    2005-07-01

    President Bush's energy program is focussed towards commercializing power production technologies that offer improvements in efficiency and reductions in emissions while utilizing the nation's most abundant energy reserve - coal. Gasification offers such benefits. To bring this technology to full commercial acceptance, the operational issue of feeding solid fuel into the pressure environment needs to be addressed. The DOE, through the National Energy Technology Laboratory, has funded research to develop the unique Stamet 'Posimetric Solids Pump' to feed coal into current gasification operating pressures. The project comprised design and testing to feed coal into 300 PSI and a second Phase for feeding into 500 PSI. The 300 PSI target was achieved in December 2003. In January 2005, the Posimetric feeder achieved continuous injection of coal into 560 PSI, exceeding the Phase 2 target. This paper presents a review and evaluation of the design, design optimizations and test results of the successful feeder. It also presents analysis of economic benefits to pump use and results from semi-commercial testing at gasifier operating test facilities, which should have commenced by the date of the Conference. 16 figs., 6 tabs.

  8. Department of Energy Closes $400 Million Loan Guarantee for State of the

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Art Solar Manufacturing in Indiana and Colorado | Department of Energy Closes $400 Million Loan Guarantee for State of the Art Solar Manufacturing in Indiana and Colorado Department of Energy Closes $400 Million Loan Guarantee for State of the Art Solar Manufacturing in Indiana and Colorado December 14, 2010 - 12:00am Addthis Washington D.C. - U.S. Energy Secretary Steven Chu announced today that a $400 million loan guarantee has been finalized for Abound Solar Manufacturing, LLC to

  9. AAC R17-3-500 Highway Encroachments and Permits | Open Energy...

    Open Energy Info (EERE)

    3-500 Highway Encroachments and Permits Jump to: navigation, search OpenEI Reference LibraryAdd to library Legal Document- RegulationRegulation: AAC R17-3-500 Highway Encroachments...

  10. Title 11 Alaska Administrative Code 82.400 - 82.475 Competitive...

    Open Energy Info (EERE)

    Reference LibraryAdd to library Legal Document- RegulationRegulation: Title 11 Alaska Administrative Code 82.400 - 82.475 Competitive BiddingLegal Abstract Implementing...

  11. INTERMEDIATE-MASS HOT CORES AT {approx}500 AU: DISKS OR OUTFLOWS?

    SciTech Connect (OSTI)

    Palau, Aina; Girart, Josep M.; Fuente, Asuncion; Alonso-Albi, Tomas; Fontani, Francesco; Sanchez-Monge, Alvaro; Boissier, Jeremie; Pietu, Vincent; Neri, Roberto; Busquet, Gemma; Estalella, Robert; Zapata, Luis A.; Zhang, Qizhou; Ho, Paul T. P.; Audard, Marc

    2011-12-20

    Observations with the Plateau de Bure Interferometer in the most extended configuration toward two intermediate-mass star-forming regions, IRAS 22198+6336 and AFGL 5142, reveal the presence of several complex organic molecules at {approx}500 AU scales, confirming the presence of hot cores in both regions. The hot cores are not rich in CN-bearing molecules, as often seen in massive hot cores, and are mainly traced by CH{sub 3}CH{sub 2}OH, (CH{sub 2}OH){sub 2}, CH{sub 3}COCH{sub 3}, and CH{sub 3}OH, with, additionally, CH{sub 3}CHO, CH{sub 3}OD, and HCOOD for IRAS 22198+6336, and C{sub 6}H and O{sup 13}CS for AFGL 5142. The emission of complex molecules is resolved down to sizes of {approx}300 and {approx}600 AU, for IRAS 22198+6336 and AFGL 5142, respectively, and most likely is tracing protostellar disks rather than flattened envelopes or toroids as is usually found. This is especially clear for the case of IRAS 22198+6336, where we detect a velocity gradient for all the mapped molecules perpendicular to the most chemically rich outflow of the region, yielding a dynamic mass {approx}> 4 M{sub Sun }. As for AFGL 5142, the hot core emission is resolved into two elongated cores separated {approx}1800 AU. A detailed comparison of the complex molecule peaks to the new CO (2-1) data and H{sub 2}O maser data from the literature suggests also that for AFGL 5142 the complex molecules are mainly associated with disks, except for a faint and extended molecular emission found to the west, which is possibly produced in the interface between one of the outflows and the dense surrounding gas.

  12. NASCAR Green Gets First Place in Daytona 500 | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    NASCAR Green Gets First Place in Daytona 500 NASCAR Green Gets First Place in Daytona 500 February 24, 2014 - 12:00am Addthis A story about how fuel cell generators were used at the Daytona 500 is currently posted on the Energy Department's blog. Read NASCAR Green Gets First Place in Daytona 500 to learn more about the potential for fuel cell generators at NASCAR events. Addthis Related Articles At this year's Daytona 500, four fuel cell generators will power some of the broadcast cameras and

  13. 300 Area waste acid treatment system closure plan

    SciTech Connect (OSTI)

    LUKE, S.N.

    1999-05-17

    The Hanford Facility Dangerous Waste Permit Application is considered to be a single application organized into a General Information Portion (document number DOERL-91-28) and a Unit-Specific Portion. The scope of the Unit-Specific Portion includes closure plan documentation submitted for individual, treatment, storage, and/or disposal units undergoing closure, such as the 300 Area Waste Acid Treatment System. Documentation contained in the General Information Portion is broader in nature and could be used by multiple treatment, storage, and/or disposal units (e.g., the glossary provided in the General Information Portion). Whenever appropriate, 300 Area Waste Acid Treatment System documentation makes cross-reference to the General Information Portion, rather than duplicating text. This 300 Area Waste Acid Treatment System Closure Plan (Revision 2) includes a Hanford Facility Dangerous Waste Permit Application, Part A, Form 3. Information provided in this closure plan is current as of April 1999.

  14. STEM Mentors Reach Nearly 300 Western Kentucky Sixth Graders | Department

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    of Energy STEM Mentors Reach Nearly 300 Western Kentucky Sixth Graders STEM Mentors Reach Nearly 300 Western Kentucky Sixth Graders November 25, 2015 - 12:00pm Addthis David Curry (far right) teaches Ayden Mowery, Jake Miller, and Bella Presson (left to right) at Ballard County Middle School to read a pH strip to test water. David Curry (far right) teaches Ayden Mowery, Jake Miller, and Bella Presson (left to right) at Ballard County Middle School to read a pH strip to test water. Ken Davis

  15. $300,000 Block Grant Awarded to Tri-City Industrial Development...

    Energy Savers [EERE]

    300,000 Block Grant Awarded to Tri-City Industrial Development Council (TRIDEC) 300,000 Block Grant Awarded to Tri-City Industrial Development Council (TRIDEC) 300,000 Block ...

  16. TYPE IIn SUPERNOVA SN 2010jl: OPTICAL OBSERVATIONS FOR OVER 500 DAYS AFTER EXPLOSION

    SciTech Connect (OSTI)

    Zhang Tianmeng; Wu Chao; Zhai Meng; Wu Hong; Fan Zhou; Zou Hu; Zhou Xu; Ma Jun; Wang Xiaofeng; Chen Juncheng; Chen Jia; Liu Qin; Huang Fang; Liang Jide; Zhao Xulin; Lin Lin; Wang Min; Dennefeld, Michel; Zhang Jujia E-mail: wang_xf@mail.tsinghua.edu.cn

    2012-11-01

    We present extensive optical observations of a Type IIn supernova (SN IIn) 2010jl for the first 1.5 years after its discovery. The UBVRI light curves demonstrated an interesting two-stage evolution during the nebular phase, which almost flatten out after about 90 days from the optical maximum. SN 2010jl has one of the highest intrinsic H{alpha} luminosities ever recorded for an SN IIn, especially at late phase, suggesting a strong interaction of SN ejecta with the dense circumstellar material (CSM) ejected by the progenitor. This is also indicated by the remarkably strong Balmer lines persisting in the optical spectra. One interesting spectral evolution about SN 2010jl is the appearance of asymmetry of the Balmer lines. These lines can be well decomposed into a narrow component and an intermediate-width component. The intermediate-width component showed a steady increase in both strength and blueshift with time until t {approx} 400 days after maximum, but it became less blueshifted at t {approx} 500 days, when the line profile appeared relatively symmetric again. Owing to the fact that a pure reddening effect will lead to a sudden decline of the light curves and a progressive blueshift of the spectral lines, we therefore propose that the asymmetric profiles of H lines seen in SN 2010jl are unlikely due to the extinction by newly formed dust inside the ejecta, contrary to the explanation by some early studies. Based on a simple CSM-interaction model, we speculate that the progenitor of SN 2010jl may suffer a gigantic mass loss ({approx}30-50 M{sub Sun }) a few decades before explosion. Considering a slow-moving stellar wind (e.g., {approx}28 km s{sup -1}) inferred for the preexisting, dense CSM shell and the extremely high mass-loss rate (1-2 M{sub Sun} yr{sup -1}), we suggest that the progenitor of SN 2010jl might have experienced a red supergiant stage and may explode finally as a post-red supergiant star with an initial mass above 30-40 M{sub Sun }.

  17. Operation and Development of the 500-keV Negative-Ion-Based Neutral Beam Injection System for JT-60U

    SciTech Connect (OSTI)

    Kuriyama, M.; Akino, N.; Ebisawa, N.; Grisham, L.; Honda, A.; Itoh, T.; Kawai, M.; Kazawa, M.; Mogaki, K.; Ohara, Y.; Ohga, T.; Okumura, Y.; Oohara, H.; Umeda, N.; Usui, K.; Watanabe, K.; Yamamoto, M.; Yamamoto, T.

    2002-09-15

    The 500-keV negative-ion based neutral beam injector for JT-60U started operation in 1996. The beam power has been increased gradually through optimizing operation parameters of the ion sources and conquering many troubles in the ion source and power supplies caused by a high voltage break-down in the accelerator. However, some issues remain to be solved concerning the ion source for increasing further the beam power and the beam energy. The most serious issue of them is non-uniformity of source plasma in the arc chamber. Various countermeasures have been implemented to improve the non-uniformity. Some of those countermeasures have been found to be partially effective in reducing the non-uniformity of the source plasma, and as the result the ion source, so far, has accelerated negative-ion beams of 17.4A at 403keV with deuterium and 20A at 360keV with hydrogen against the goal of 22A at 500keV. The neutral beam injection power into the plasma has reached 5.8MW at 400keV with deuterium. Further efforts to reach the target of 10MW at 500keV have been continued.

  18. Updated Conceptual Model for the 300 Area Uranium Groundwater Plume

    SciTech Connect (OSTI)

    Zachara, John M.; Freshley, Mark D.; Last, George V.; Peterson, Robert E.; Bjornstad, Bruce N.

    2012-11-01

    The 300 Area uranium groundwater plume in the 300-FF-5 Operable Unit is residual from past discharge of nuclear fuel fabrication wastes to a number of liquid (and solid) disposal sites. The source zones in the disposal sites were remediated by excavation and backfilled to grade, but sorbed uranium remains in deeper, unexcavated vadose zone sediments. In spite of source term removal, the groundwater plume has shown remarkable persistence, with concentrations exceeding the drinking water standard over an area of approximately 1 km2. The plume resides within a coupled vadose zone, groundwater, river zone system of immense complexity and scale. Interactions between geologic structure, the hydrologic system driven by the Columbia River, groundwater-river exchange points, and the geochemistry of uranium contribute to persistence of the plume. The U.S. Department of Energy (DOE) recently completed a Remedial Investigation/Feasibility Study (RI/FS) to document characterization of the 300 Area uranium plume and plan for beginning to implement proposed remedial actions. As part of the RI/FS document, a conceptual model was developed that integrates knowledge of the hydrogeologic and geochemical properties of the 300 Area and controlling processes to yield an understanding of how the system behaves and the variables that control it. Recent results from the Hanford Integrated Field Research Challenge site and the Subsurface Biogeochemistry Scientific Focus Area Project funded by the DOE Office of Science were used to update the conceptual model and provide an assessment of key factors controlling plume persistence.

  19. Hanford’s 300 Area Sees Dramatic Progress

    Broader source: Energy.gov [DOE]

    RICHLAND, Wash. – EM’s Richland Operations Office and its contractor Washington Closure Hanford (WCH) have made tremendous progress in cleaning up areas along the Columbia River at the Hanford Site in the past 10 years. The progress is especially visible in the 300 Area, a former industrial area that covered 1,700 acres at the site’s southern edge.

  20. Efforts to Develop a 300°C Solder

    SciTech Connect (OSTI)

    Norann, Randy A

    2015-01-25

    This paper covers the efforts made to find a 300°C electrical solder solution for geothermal well monitoring and logging tools by Perma Works LLC. This paper covers: why a high temperature solder is needed, what makes for a good solder, testing flux, testing conductive epoxy and testing intermetallic bonds. Future areas of research are suggested.

  1. 300 area TEDF NPDES Permit Compliance Monitoring Plan

    SciTech Connect (OSTI)

    Loll, C.M.

    1995-09-05

    This document presents the 300 Area Treated Effluent Disposal Facility (TEDF) National Pollutant Discharge Elimination System (NPDES) Permit Compliance Monitoring Plan (MP). The MP describes how ongoing monitoring of the TEDF effluent stream for compliance with the NPDES permit will occur. The MP also includes Quality Assurance protocols to be followed.

  2. Observation of Parametric X-Rays Produced by 400-GeV/C Protons in Bent

    Office of Scientific and Technical Information (OSTI)

    Crystals (Journal Article) | SciTech Connect Parametric X-Rays Produced by 400-GeV/C Protons in Bent Crystals Citation Details In-Document Search Title: Observation of Parametric X-Rays Produced by 400-GeV/C Protons in Bent Crystals Spectral maxima of parametric X-ray radiation (PXR) produced by 400 GeV/c protons in bent silicon crystals aligned with the beam have been observed in an experiment at the H8 external beam of the CERN SPS. The total yield of PXR photons was about 10{sup -6} per

  3. Observation of parametric X-rays produced by 400 GeV/c protons in bent

    Office of Scientific and Technical Information (OSTI)

    crystals (Journal Article) | SciTech Connect parametric X-rays produced by 400 GeV/c protons in bent crystals Citation Details In-Document Search Title: Observation of parametric X-rays produced by 400 GeV/c protons in bent crystals Spectral maxima of parametric X-ray radiation (PXR) produced by 400 GeV/c protons in bent silicon crystals aligned with the beam have been observed in an experiment at the H8 external beam of the CERN SPS. The total yield of PXR photons was about 10{sup -6} per

  4. DOE's Carbon Utilization and Storage Atlas Estimates at Least 2,400 Billion

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Metric Tons of U.S. CO2 Storage Resource | Department of Energy Carbon Utilization and Storage Atlas Estimates at Least 2,400 Billion Metric Tons of U.S. CO2 Storage Resource DOE's Carbon Utilization and Storage Atlas Estimates at Least 2,400 Billion Metric Tons of U.S. CO2 Storage Resource December 19, 2012 - 12:00pm Addthis Washington, DC - The United States has at least 2,400 billion metric tons of possible carbon dioxide (CO2) storage resource in saline formations, oil and gas

  5. Volume Reflection Dependence of 400 GeV/c Protons on the Bent Crystal

    Office of Scientific and Technical Information (OSTI)

    Curvature (Journal Article) | SciTech Connect Volume Reflection Dependence of 400 GeV/c Protons on the Bent Crystal Curvature Citation Details In-Document Search Title: Volume Reflection Dependence of 400 GeV/c Protons on the Bent Crystal Curvature The trend of volume reflection parameters (deflection angle and efficiency) in a bent (110) silicon crystal has been investigated as a function of the crystal curvature with 400 GeV/c protons on the H8 beam line at the CERN Super Proton

  6. Investigating the presence of 500 μm submillimeter excess emission in

    Office of Scientific and Technical Information (OSTI)

    local star forming galaxies (Journal Article) | SciTech Connect Investigating the presence of 500 μm submillimeter excess emission in local star forming galaxies Citation Details In-Document Search Title: Investigating the presence of 500 μm submillimeter excess emission in local star forming galaxies Submillimeter excess emission has been reported at 500 μm in a handful of local galaxies, and previous studies suggest that it could be correlated with metal abundance. We investigate the

  7. U.S. Department of Energy Announces Completion of 500 Industrial Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Saving Assessment | Department of Energy Completion of 500 Industrial Energy Saving Assessment U.S. Department of Energy Announces Completion of 500 Industrial Energy Saving Assessment May 9, 2008 - 11:30am Addthis Over 80 Trillion Btus of Natural Gas Savings Found WASHINGTON - The U.S. Department of Energy (DOE) today announced that it has completed the 500th Energy Saving Assessment (ESA) at the nation's largest industrial facilities. These assessments have helped companies identify

  8. NASCAR Green Gets First Place in Daytona 500 | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    NASCAR Green Gets First Place in Daytona 500 NASCAR Green Gets First Place in Daytona 500 February 21, 2014 - 10:20am Addthis At this year's Daytona 500, four fuel cell generators will power some of the broadcast cameras and spotlights, demonstrating how the technology could help NASCAR save money on fuel costs. This technology was beta-tested during the IMSA Rolex 24 race weekend last month. | Photo courtesy of P.T. Jones, Oak Ridge National Lab. At this year's Daytona 500, four fuel cell

  9. EIS-0344: Grand Coulee-Bell 500 kV Transmission Line

    Broader source: Energy.gov [DOE]

    This EIS analyzes DOE's proposed action for the construction and operation of the proposed Grand Coulee-Bell 500-kV Transmission Line Project.

  10. Low-noise low-jitter 32-pixels CMOS single-photon avalanche diodes array for single-photon counting from 300 nm to 900 nm

    SciTech Connect (OSTI)

    Scarcella, Carmelo; Tosi, Alberto Villa, Federica; Tisa, Simone; Zappa, Franco

    2013-12-15

    We developed a single-photon counting multichannel detection system, based on a monolithic linear array of 32 CMOS SPADs (Complementary Metal-Oxide-Semiconductor Single-Photon Avalanche Diodes). All channels achieve a timing resolution of 100 ps (full-width at half maximum) and a photon detection efficiency of 50% at 400 nm. Dark count rate is very low even at room temperature, being about 125 counts/s for 50 ?m active area diameter SPADs. Detection performance and microelectronic compactness of this CMOS SPAD array make it the best candidate for ultra-compact time-resolved spectrometers with single-photon sensitivity from 300 nm to 900 nm.

  11. Oil Shale Market is Estimated to Reach USD 7,400.70 Million by...

    Open Energy Info (EERE)

    Oil Shale Market is Estimated to Reach USD 7,400.70 Million by 2022 Home > Groups > Renewable Energy RFPs Wayne31jan's picture Submitted by Wayne31jan(150) Contributor 1 July, 2015...

  12. Application for Presidential Permit PP-400 TDI-NE - New England...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    PP-400 TDI-NE - New England Clean Power Link Project - Motion to Intervene and Comments of the Vermont Department of Public Service - August 6, 2014 Application for Presidential ...

  13. Modeling and Simulations for the High Flux Isotope Reactor Cycle 400

    Office of Scientific and Technical Information (OSTI)

    (Technical Report) | SciTech Connect Technical Report: Modeling and Simulations for the High Flux Isotope Reactor Cycle 400 Citation Details In-Document Search Title: Modeling and Simulations for the High Flux Isotope Reactor Cycle 400 × You are accessing a document from the Department of Energy's (DOE) SciTech Connect. This site is a product of DOE's Office of Scientific and Technical Information (OSTI) and is provided as a public service. Visit OSTI to utilize additional information

  14. Application for Presidential Permit OE Docket No. PP-400 TDI-New England -

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    New England Clean Power Link Project | Department of Energy New England - New England Clean Power Link Project Application for Presidential Permit OE Docket No. PP-400 TDI-New England - New England Clean Power Link Project Application from TDI-NE to construct, operate and maintain electric transmission facilities at the U.S. - Canada Border. PDF icon PP-400 TDI-New England Application with Appendices.pdf More Documents & Publications EIS-0503: Final Environmental Impact Statement

  15. Summary - Building C-400 Thermal Treatment Remedial Design Report and Investigation, Paducah, Kentucky

    Office of Environmental Management (EM)

    Paducah, KY EM Project: Building C400 Thermal Treatment ETR Report Date: August 2007 ETR-8 United States Department of Energy Office of Environmental Management (DOE-EM) External Technical Review of Building C-400 Thermal Treatment 90% Remedial Design Report and Site Investigation, Paducah Kentucky Why DOE-EM Did This Review The groundwater underlying the Paducah Gaseous Diffusion Plant (PGDP) is contaminated by chlorinated solvents, principally trichloroethylene (TCE), as well as other

  16. Obama Administration Announces Additional $102,508,400 for Local Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Efficiency Improvements in Pennsylvania | Department of Energy 2,508,400 for Local Energy Efficiency Improvements in Pennsylvania Obama Administration Announces Additional $102,508,400 for Local Energy Efficiency Improvements in Pennsylvania March 26, 2009 - 12:00am Addthis WASHINGTON - Vice President Joe Biden and Energy Secretary Steven Chu today announced plans to invest $3.2 billion in energy efficiency and conservation projects in U.S. cities, counties, states, territories, and Native

  17. Obama Administration Announces Additional $20,117,400 for Local Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Efficiency Improvements in Arkansas | Department of Energy ,117,400 for Local Energy Efficiency Improvements in Arkansas Obama Administration Announces Additional $20,117,400 for Local Energy Efficiency Improvements in Arkansas March 26, 2009 - 12:00am Addthis WASHINGTON - Vice President Joe Biden and Energy Secretary Steven Chu today announced plans to invest $3.2 billion in energy efficiency and conservation projects in U.S. cities, counties, states, territories, and Native American

  18. Obama Administration Announces Additional $63,817,400 for Local Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Efficiency Improvements in Arizona | Department of Energy 63,817,400 for Local Energy Efficiency Improvements in Arizona Obama Administration Announces Additional $63,817,400 for Local Energy Efficiency Improvements in Arizona March 26, 2009 - 12:00am Addthis WASHINGTON - Vice President Joe Biden and Energy Secretary Steven Chu today announced plans to invest $3.2 billion in energy efficiency and conservation projects in U.S. cities, counties, states, territories, and Native American tribes.

  19. Rebate program brings 16,300 rebates to Sooner State

    Broader source: Energy.gov [DOE]

    Oklahoma's Appliance Rebate Program swept through the plains in May, providing residents a break on upfront appliance costs and ensuring long-term energy savings. Oklahomans claimed more than 16,300 rebates in less than a month on ENERGY STAR refrigerators, clothes washers, single room air conditioners, water heathers, central air conditioners, air-source heat pumps, furnaces and ground-source heat pumps.

  20. Microsoft PowerPoint - 300 Area Perspective.pptx

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Area Perspective 300 Area Perspective River and Plateau Committee February 15, 2012 February 15, 2012 John B. Price Business/Research Park in N Richland h d l h High Density Residential is the norm MSA Bldg and Townhouses "Smartpark" includes Townhouses High Density Residential Infiltration from Impervious Areas & Irrigation Townhouses Grass Townhouse Townhouses Grass Bare Ground from Construction Storm Sewer Asphalt Grass Grate p Remediated 1100 Area -Industrial Area f h l ff

  1. 300 Area TEDF NPDES Permit Compliance Monitoring Plan

    SciTech Connect (OSTI)

    Loll, C.M.

    1994-10-13

    This monitoring plan describes the activities and methods that will be employed at the 300 Area Treated Effluent Disposal Facility (TEDF) in order to ensure compliance with the National Discharge Elimination System (NPDES) permit. Included in this document are a brief description of the project, the specifics of the sampling effort, including the physical location and frequency of sampling, the support required for sampling, and the Quality Assurance (QA) protocols to be followed in the sampling procedures.

  2. High Temperature 300°C Directional Drilling System

    SciTech Connect (OSTI)

    Chatterjee, Kamalesh; Aaron, Dick; Macpherson, John

    2015-07-31

    Many countries around the world, including the USA, have untapped geothermal energy potential. Enhanced Geothermal Systems (EGS) technology is needed to economically utilize this resource. Temperatures in some EGS reservoirs can exceed 300°C. To effectively utilize EGS resources, an array of injector and production wells must be accurately placed in the formation fracture network. This requires a high temperature directional drilling system. Most commercial services for directional drilling systems are rated for 175°C while geothermal wells require operation at much higher temperatures. Two U.S. Department of Energy (DOE) Geothermal Technologies Program (GTP) projects have been initiated to develop a 300°C capable directional drilling system, the first developing a drill bit, directional motor, and drilling fluid, and the second adding navigation and telemetry systems. This report is for the first project, “High Temperature 300°C Directional Drilling System, including drill bit, directional motor and drilling fluid, for enhanced geothermal systems,” award number DE-EE0002782. The drilling system consists of a drill bit, a directional motor, and drilling fluid. The DOE deliverables are three prototype drilling systems. We have developed three drilling motors; we have developed four roller-cone and five Kymera® bits; and finally, we have developed a 300°C stable drilling fluid, along with a lubricant additive for the metal-to-metal motor. Metal-to-metal directional motors require coatings to the rotor and stator for wear and corrosion resistance, and this coating research has been a significant part of the project. The drill bits performed well in the drill bit simulator test, and the complete drilling system has been tested drilling granite at Baker Hughes’ Experimental Test Facility in Oklahoma. The metal-to-metal motor was additionally subjected to a flow loop test in Baker Hughes’ Celle Technology Center in Germany, where it ran for more than 100 hours.

  3. Use of underpotential deposition of zinc to mitigate hydrogen absorption into Monel K500

    SciTech Connect (OSTI)

    Zheng, G.; Popov, B.N.; White, R.E. . Dept. of Chemical Engineering)

    1994-05-01

    Polarization experiments and a potentiostatic pulse technique have been used to show that a monolayer coverage of zinc effectively inhibits the absorption of hydrogen into Monel K500. By depositing a monolayer of zinc on Monel K500 the hydrogen, evolution reaction and hydrogen ingress flux rate were reduced by 60%.

  4. SunShot-Supported Company to Create 500 New Solar Manufacturing Jobs

    Broader source: Energy.gov [DOE]

    SunShot awardee Suniva, a manufacturer of high efficiency crystalline silicone solar cells and modules, has announced it will expand its manufacturing capacity at its Georgia headquarters to 400MW...

  5. Investigating the presence of 500 μm submillimeter excess emission in local star forming galaxies

    SciTech Connect (OSTI)

    Kirkpatrick, Allison; Calzetti, Daniela; Galametz, Maud; Kennicutt, Rob Jr.; Dale, Daniel; Aniano, Gonzalo; Sandstrom, Karin; Walter, Fabian; Armus, Lee; Crocker, Alison; Hinz, Joannah; Hunt, Leslie; Koda, Jin

    2013-11-20

    Submillimeter excess emission has been reported at 500 μm in a handful of local galaxies, and previous studies suggest that it could be correlated with metal abundance. We investigate the presence of an excess submillimeter emission at 500 μm for a sample of 20 galaxies from the Key Insights on Nearby Galaxies: a Far Infrared Survey with Herschel (KINGFISH) that span a range of morphologies and metallicities (12 + log (O/H) = 7.8-8.7). We probe the far-infrared (IR) emission using images from the Spitzer Space Telescope and Herschel Space Observatory in the wavelength range 24-500 μm. We model the far-IR peak of the dust emission with a two-temperature modified blackbody and measure excess of the 500 μm photometry relative to that predicted by our model. We compare the submillimeter excess, where present, with global galaxy metallicity and, where available, resolved metallicity measurements. We do not find any correlation between the 500 μm excess and metallicity. A few individual sources do show excess (10%-20%) at 500 μm; conversely, for other sources, the model overpredicts the measured 500 μm flux density by as much as 20%, creating a 500 μm 'deficit'. None of our sources has an excess larger than the calculated 1σ uncertainty, leading us to conclude that there is no substantial excess at submillimeter wavelengths at or shorter than 500 μm in our sample. Our results differ from previous studies detecting 500 μm excess in KINGFISH galaxies largely due to new, improved photometry used in this study.

  6. Low-field magnetoresistance up to 400 K in double perovskite Sr{sub 2}FeMoO{sub 6} synthesized by a citrate route

    SciTech Connect (OSTI)

    Harnagea, L.; Jurca, B.; Berthet, P.

    2014-03-15

    A wet-chemistry technique, namely the citrate route, has been used to prepare high-quality polycrystalline samples of double perovskite Sr{sub 2}FeMoO{sub 6}. We report on the evolution of magnetic and magnetoresistive properties of the synthesized samples as a function of three parameters (i) the pH of the starting solution, (ii) the decomposition temperature of the citrate precursors and (iii) the sintering conditions. The low-field magnetoresistance (LFMR) value of our best samples is as high as 5% at room temperature for an applied magnetic field of 1 kOe. Additionally, the distinguishing feature of these samples is the persistence of LFMR, with a reasonably large value, up to 400 K which is a crucial parameter for any practical application. Our study indicates that the enhancement of LFMR observed is due to a good compromise between the grain size distribution and their magnetic polarization. -- Graphical abstract: The microstructure (left panel) and corresponding low-field magnetoresistance of one of the Sr{sub 2}FeMoO{sub 6} samples synthesized in the course of this work. Highlights: Samples of Sr{sub 2}FeMoO{sub 6} are prepared using a citrate route under varying conditions. Magnetoresistive properties are improved and optimized. Low-field magnetoresitence values as large as 5% at 300 K/1 kOe are reported. Persistence of low-field magnetoresistance up to 400 K.

  7. Intermetallic phase formation and breakdown of Mo diffusion barriers in Ni-Mo-Cu and Ni-Mo-Monel 400 diffusion triads

    SciTech Connect (OSTI)

    Shueh, Y.

    1988-01-01

    The purpose of this research was to study the kinetics of compound formation and the interdiffusion behavior of a sacrificial type diffusion barrier in a model system. Ni-Mo diffusion couples were annealed in an inert atmosphere at 950-1050{degree}C for 5-300 hours. Ni-Mo-Cu and Ni-Mo-Monel 400 diffusion triads with varied thicknesses of Mo layers sandwiched by Ni and C or Monel 400 disks were annealed under the same conditions. Parabolic growth of the intermetallic phase, {beta}, was observed at 1000{degree}C and 1050{degree}C in the semi-infinite Ni-Mo diffusion couple an din the Ni-Mo-Cu diffusion triad when a finite thickness of the Mo layer remained. The {beta} phase exhibited more or less planar morphology except in the case of some extremely rugged interfaces which were associated with grain boundaries adjacent to these interfaces. Dissociation and recession of the compound layer in Ni-Mo-Cu diffusion triads initiated when the Mo layer was nearly consumed. The product phases of the dissociation reaction are consistent with those predicted from the Ni-Mo-Cu ternary phase diagram. Numerical methods based on a finite difference technique, and an analytical solution based on diffusion controlled parabolic growth and quasi-steady-state approximation in the {beta} phase region were used to analyze the results.

  8. A Preclinical Study of the Safety and Efficacy of Occlusin Trade-Mark-Sign 500 Artificial Embolization Device in Sheep

    SciTech Connect (OSTI)

    Owen, Richard J.; Nation, Patrick N.; Polakowski, Robert; Biliske, Jennifer A.; Tiege, Paul B.

    2012-06-15

    Introduction: This study evaluated the safety, effectiveness, and biodegradation of a new embolic agent, Occlusin Trade-Mark-Sign 503 Artificial Embolization Device (OCL 503). The agent consists of biodegradable poly-lactic-co-glycolic acid microspheres (150-212 {mu}m) coated with type I bovine collagen and was compared with Embosphere{sup Registered-Sign} Microspheres (300-500 {mu}m) in this controlled study of uterine artery embolization (UAE) in sheep. Methods: Unilateral UAE was performed in 32 adult ewes randomly assigned. Vessels were embolized to effective stasis. The cohort was divided into four groups, which were sacrificed at 1, 3, 6, and 12 months. Results: Both agents were 100% effective in achieving stasis. At 6 months, all OCL 503-treated arteries were occluded, the microspheres degraded with time, and at 12 months all four animals examined demonstrated recanalization. OCL 503 was found in the untreated uterine artery in one animal with no other evidence of non target embolization. In the Embosphere-treated group, all vessels remained occluded and microspheres were detected in the contralateral uterine artery in 6 of 15 examined vessels and in 10 vaginal, 2 ovarian, and 1 vesical artery. No procedural-related complications were seen in either group. Conclusions: OCL 503 is as effective an embolic agent as Embosphere{sup Registered-Sign} Microspheres when embolizing ovine uterine arteries and resorbs with time, allowing recanalization of the treated arteries. No device-related issues or adverse events were observed.

  9. Meteorological Observations for Renewable Energy Applications at Site 300

    SciTech Connect (OSTI)

    Wharton, S; Alai, M; Myers, K

    2011-10-26

    In early October 2010, two Laser and Detection Ranging (LIDAR) units (LIDAR-96 and LIDAR-97), a 3 m tall flux tower, and a 3 m tall meteorological tower were installed in the northern section of Site 300 (Figure 1) as a first step in development of a renewable energy testbed facility. This section of the SMS project is aimed at supporting that effort with continuous maintenance of atmospheric monitoring instruments capable of measuring vertical profiles of wind speed and wind direction at heights encountered by future wind power turbines. In addition, fluxes of energy are monitored to estimate atmospheric mixing and its effects on wind flow properties at turbine rotor disk heights. Together, these measurements are critical for providing an accurate wind resource characterization and for validating LLNL atmospheric prediction codes for future renewable energy projects at Site 300. Accurate, high-resolution meteorological measurements of wind flow in the planetary boundary layer (PBL) and surface-atmosphere energy exchange are required for understanding the properties and quality of available wind power at Site 300. Wind speeds at heights found in a typical wind turbine rotor disk ({approx} 40-140 m) are driven by the synergistic impacts of atmospheric stability, orography, and land-surface characteristics on the mean wind flow in the PBL and related turbulence structures. This section of the report details the maintenance and labor required in FY11 to optimize the meteorological instruments and ensure high accuracy of their measurements. A detailed look at the observations from FY11 is also presented. This portion of the project met the following milestones: Milestone 1: successful maintenance and data collection of LIDAR and flux tower instruments; Milestone 2: successful installation of solar power for the LIDAR units; and Milestone 3: successful implementation of remote data transmission for the LIDAR units.

  10. Developing a 300C Analog Tool for EGS

    SciTech Connect (OSTI)

    Normann, Randy

    2015-03-23

    This paper covers the development of a 300°C geothermal well monitoring tool for supporting future EGS (enhanced geothermal systems) power production. This is the first of 3 tools planed. This is an analog tool designed for monitoring well pressure and temperature. There is discussion on 3 different circuit topologies and the development of the supporting surface electronics and software. There is information on testing electronic circuits and component. One of the major components is the cable used to connect the analog tool to the surface.

  11. Results from ORNL Characterization of Zr02-500-AK2 - Surrogate TRISO Material

    SciTech Connect (OSTI)

    Hunn, John D; Kercher, Andrew K

    2005-06-01

    This document is a compilation of the characterization data for the TRISO-coated surrogate particle batch designated ZrO2-500-AK2 that was produced at Oak Ridge National Laboratory (ORNL) as part of the Advanced Gas Reactor Fuel Development and Qualification (AGR) program. The ZrO2-500-AK2 material contains nominally 500 {micro}m kernels of yttria-stabilized zirconia (YSZ) coated with all TRISO layers (buffer, inner pyrocarbon, silicon carbide, and outer pyrocarbon). The ZrO2-500-AK2 material was created for: (1) irradiation testing in the High Flux Isotope Reactor (HFIR) and (2) limited dissemination to laboratories as deemed appropriate to the AGR program. This material was created midway into a TRISO fuel development program to accommodate a sudden opportunity to perform irradiation testing on surrogate material. While the layer deposition processes were chosen based on the best technical understanding at the time, technical progress at ORNL has led to an evolution in the perceived optimal deposition conditions since the createion of ZrO2-500-AK2. Thus, ZrO2-500-AK2 contains a reasonable TRISO microstructure, but does differ significanly from currently produced TRISO surrogates and fuel at ORNL. In this document, characterization data of the ZrO2-500-AK2 surrogate includes: size, shape, coating thickness, and density.

  12. Results from ORNL characterization of ZrO2-500-AK2 - surrogate TRISO material

    SciTech Connect (OSTI)

    Kercher, Andrew K; Hunn, John D

    2005-06-01

    This document is a compilation of the characterization data for the TRISO-coated surrogate particles designated ZrO2-500-AK2 that was produced at Oak Ridge National Laboratory (ORNL) as part of the Advanced Gas Reactor Fuel Development and Qualification (AGR) program. The ZrO2-500-AK2 material contains nominally 500 {micro}m kernels of yttria-stabilized zirconia (YSZ) coated with all TRISO layers (buffer, inner pyrocarbon, silicon carbide, and outer pyrocarbon). The ZrO2-500-AK2 material was created for: (1) irradiation testing in the High Flux Isotope Reactor (HFIR) and (2) limited dissemination to laboratories as deemed appropriate to the AGR program. This material was created midway into a TRISO fuel development program to accommodate a sudden opportunity to perform irradiation testing on surrogate material. While the layer deposition processes were chosen based on the best technical understanding at the time, technical progress at ORNL has led to an evolution in the perceived optimal deposition conditions since the creation of ZrO2-500-AK2. Thus, ZrO2-500-AK2 contains a reasonable TRISO microstructure, but does differ significantly from currently produced TRISO surrogates and fuel at ORNL. In this document, characterization data of the ZrO2-500-AK2 surrogate includes: size, shape, coating thickness, and density.

  13. EERE Success Story-SunShot-funded Advanced Inverter Testing Enables 2,500

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Solar Energy Systems to Connect to Hawaii's Electric Grid | Department of Energy SunShot-funded Advanced Inverter Testing Enables 2,500 Solar Energy Systems to Connect to Hawaii's Electric Grid EERE Success Story-SunShot-funded Advanced Inverter Testing Enables 2,500 Solar Energy Systems to Connect to Hawaii's Electric Grid January 22, 2015 - 3:45pm Addthis Thanks to a SunShot collaboration at the Energy Department's National Renewable Energy Laboratory (NREL) more than 2,500 Hawaiian

  14. Issues surrounding the use of nickel-copper alloy K-500 fasteners in seawater

    SciTech Connect (OSTI)

    Natishan, M.E.; Porr, W.C. Jr.

    1994-12-31

    Nickel-copper alloy K-500 has long been used for the manufacture of fasteners for seawater applications. Alloy K-500 is a nickel-copper solid solution, precipitation strengthened with fine gamma prime precipitates to give it high strength, toughness and good general corrosion resistance. As the use of K-500 has increased in seawater, specifically in seawater tanks protected with anodes, its susceptibility to hydrogen embrittlement has come to light. Several recent failures in air suggest other rate-dependent failures mechanisms for this alloy that must be considered in fastener applications. These failure mechanisms and their interactions will be discussed.

  15. 300 Area Uranium Stabilization Through Polyphosphate Injection: Final Report

    SciTech Connect (OSTI)

    Vermeul, Vincent R.; Bjornstad, Bruce N.; Fritz, Brad G.; Fruchter, Jonathan S.; Mackley, Rob D.; Newcomer, Darrell R.; Mendoza, Donaldo P.; Rockhold, Mark L.; Wellman, Dawn M.; Williams, Mark D.

    2009-06-30

    The objective of the treatability test was to evaluate the efficacy of using polyphosphate injections to treat uranium-contaminated groundwater in situ. A test site consisting of an injection well and 15 monitoring wells was installed in the 300 Area near the process trenches that had previously received uranium-bearing effluents. This report summarizes the work on the polyphosphate injection project, including bench-scale laboratory studies, a field injection test, and the subsequent analysis and interpretation of the results. Previous laboratory tests have demonstrated that when a soluble form of polyphosphate is injected into uranium-bearing saturated porous media, immobilization of uranium occurs due to formation of an insoluble uranyl phosphate, autunite [Ca(UO2)2(PO4)2•nH2O]. These tests were conducted at conditions expected for the aquifer and used Hanford soils and groundwater containing very low concentrations of uranium (10-6 M). Because autunite sequesters uranium in the oxidized form U(VI) rather than forcing reduction to U(IV), the possibility of re-oxidation and subsequent re-mobilization is negated. Extensive testing demonstrated the very low solubility and slow dissolution kinetics of autunite. In addition to autunite, excess phosphorous may result in apatite mineral formation, which provides a long-term source of treatment capacity. Phosphate arrival response data indicate that, under site conditions, the polyphosphate amendment could be effectively distributed over a relatively large lateral extent, with wells located at a radial distance of 23 m (75 ft) reaching from between 40% and 60% of the injection concentration. Given these phosphate transport characteristics, direct treatment of uranium through the formation of uranyl-phosphate mineral phases (i.e., autunite) could likely be effectively implemented at full field scale. However, formation of calcium-phosphate mineral phases using the selected three-phase approach was problematic. Although amendment arrival response data indicate some degree of overlap between the reactive species and thus potential for the formation of calcium-phosphate mineral phases (i.e., apatite formation), the efficiency of this treatment approach was relatively poor. In general, uranium performance monitoring results support the hypothesis that limited long-term treatment capacity (i.e., apatite formation) was established during the injection test. Two separate overarching issues affect the efficacy of apatite remediation for uranium sequestration within the 300 Area: 1) the efficacy of apatite for sequestering uranium under the present geochemical and hydrodynamic conditions, and 2) the formation and emplacement of apatite via polyphosphate technology. In addition, the long-term stability of uranium sequestered via apatite is dependent on the chemical speciation of uranium, surface speciation of apatite, and the mechanism of retention, which is highly susceptible to dynamic geochemical conditions. It was expected that uranium sequestration in the presence of hydroxyapatite would occur by sorption and/or surface complexation until all surface sites have been depleted, but that the high carbonate concentrations in the 300 Area would act to inhibit the transformation of sorbed uranium to chernikovite and/or autunite. Adsorption of uranium by apatite was never considered a viable approach for in situ uranium sequestration in and of itself, because by definition, this is a reversible reaction. The efficacy of uranium sequestration by apatite assumes that the adsorbed uranium would subsequently convert to autunite, or other stable uranium phases. Because this appears to not be the case in the 300 Area aquifer, even in locations near the river, apatite may have limited efficacy for the retention and long-term immobilization of uranium at the 300 Area site..

  16. Modeling and Simulations for the High Flux Isotope Reactor Cycle 400

    Office of Scientific and Technical Information (OSTI)

    (Technical Report) | SciTech Connect Modeling and Simulations for the High Flux Isotope Reactor Cycle 400 Citation Details In-Document Search Title: Modeling and Simulations for the High Flux Isotope Reactor Cycle 400 A concerted effort over the past few years has been focused on enhancing the core model for the High Flux Isotope Reactor (HFIR), as part of a comprehensive study for HFIR conversion from high-enriched uranium (HEU) to low-enriched uranium (LEU) fuel. At this time, the core

  17. U.S. Department of Energy Announces Completion of 500 Industrial...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    "Completing the 500th assessment is a major milestone in our continued work to reduce U.S. industrial energy intensity by 25 percent, while furthering the President's commitment to ...

  18. Investigation of the EAS Lateral Particle Density at 500 m Distance from Shower Core

    SciTech Connect (OSTI)

    Toma, G.

    2008-01-24

    For the experimental conditions of the KASCADE-Grande experiment, the density of EAS charged particles at the distance of about 500 m from the shower core S(500) has been shown by detailed simulation studies to be an approximate energy estimator, being nearly independent of the mass of the primary particle. This report presents some experimentally observed features of the S(500) observable registered with the KASCADE-Grande array installed at the Forschungszentrum Karlsruhe, Germany The measured energy deposits of particles in the 37 scintillation detector stations have been used to reconstruct the lateral charged particle distributions that are described by a Linsley parameterization (LDF). Among other features, the S(500) dependence from the EAS angle of incidence has been studied.

  19. Treasury, Energy Announce $500 Million in Awards for Clean Energy Projects

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    | Department of Energy $500 Million in Awards for Clean Energy Projects Treasury, Energy Announce $500 Million in Awards for Clean Energy Projects September 1, 2009 - 12:00am Addthis WASHINGTON- Marking a major milestone in the effort to spur private sector investments in clean energy and create new jobs for America's workers, Treasury Secretary Tim Geithner and Energy Secretary Steven Chu today announced $502 million in the first round of awards from an American Recovery and Reinvestment

  20. Obama Administration Announces Additional $13,167,500 for Local Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Efficiency Improvements in South Dakota | Department of Energy 3,167,500 for Local Energy Efficiency Improvements in South Dakota Obama Administration Announces Additional $13,167,500 for Local Energy Efficiency Improvements in South Dakota March 26, 2009 - 12:00am Addthis WASHINGTON - Vice President Joe Biden and Energy Secretary Steven Chu today announced plans to invest $3.2 billion in energy efficiency and conservation projects in U.S. cities, counties, states, territories, and Native

  1. EERE Success Story-SunShot-Supported Company to Create 500 New Solar

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Manufacturing Jobs | Department of Energy Company to Create 500 New Solar Manufacturing Jobs EERE Success Story-SunShot-Supported Company to Create 500 New Solar Manufacturing Jobs October 2, 2015 - 10:03am Addthis Suniva employee doing quality assurance testing at its Georgia headquarters. Photo Courtesy: Suniva Suniva employee doing quality assurance testing at its Georgia headquarters. Photo Courtesy: Suniva SunShot awardee Suniva, a manufacturer of high efficiency crystalline silicone

  2. NREL Employees and Managing Partner Pledge $500,000 to Aid Area Charities -

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    News Releases | NREL Employees and Managing Partner Pledge $500,000 to Aid Area Charities 2013 charitable giving campaign surpasses previous giving record December 13, 2012 The employees of the National Renewable Energy Laboratory (NREL) and the Alliance for Sustainable Energy, LLC, have pledged more than $500,000 to support local charities during the lab's annual holiday giving campaign. NREL employees have committed more than $466,000 to the Partnership for Colorado, Mile High United Way

  3. Department of Energy-funded Bioenergy Research Centers File 500th Invention

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Disclosure | Department of Energy Energy-funded Bioenergy Research Centers File 500th Invention Disclosure Department of Energy-funded Bioenergy Research Centers File 500th Invention Disclosure March 7, 2016 - 2:47pm Addthis News release from Oak Ridge National Laboratory and the Great Lakes Bioenergy Research Center OAK RIDGE, Tenn., March 3, 2016-Three U.S. Department of Energy-funded research centers - the BioEnergy Science Center (Oak Ridge National Laboratory), the Great Lakes Bioenergy

  4. EIS-0514: Colusa-Sutter 500-kilovolt Transmission Line Project; Colusa and

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Sutter Counties, California | Department of Energy 14: Colusa-Sutter 500-kilovolt Transmission Line Project; Colusa and Sutter Counties, California EIS-0514: Colusa-Sutter 500-kilovolt Transmission Line Project; Colusa and Sutter Counties, California Summary Western Area Power Administration (Western) and the Sacramento Municipal Utility District (SMUD) are preparing a joint EIS/environmental impact report (EIR) -under, respectively, NEPA and the California Environmental Quality Act - that

  5. Delisting petition for 300-M saltstone (treated F006 sludge) from the 300-M liquid effluent treatment facility

    SciTech Connect (OSTI)

    Not Available

    1989-04-04

    This petition seeks exclusion for stabilized and solidified sludge material generated by treatment of wastewater from the 300-M aluminum forming and metal finishing processes. The waste contains both hazardous and radioactive components and is classified as a mixed waste. The objective of this petition is to demonstrate that the stabilized sludge material (saltstone), when properly disposed, will not exceed the health-based standards for the hazardous constituents. This petition contains sampling and analytical data which justify the request for exclusion. The results show that when the data are applied to the EPA Vertical and Horizontal Spread (VHS) Model, health-based standards for all hazardous waste constituents will not be exceeded during worst case operating and environmental conditions. Disposal of the stabilized sludge material in concrete vaults will meet the requirements pertaining to Waste Management Activities for Groundwater Protection at the Savannah River Site in Aiken, S.C. Documents set forth performance objectives and disposal options for low-level radioactive waste disposal. Concrete vaults specified for disposal of 300-M saltstone (treated F006 sludge) assure that these performance objectives will be met.

  6. Department of Energy Awards $300,000 to Tri-City Industrial Developmen...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    300,000 to Tri-City Industrial Development Council in Washington State Department of Energy Awards 300,000 to Tri-City Industrial Development Council in Washington State ...

  7. Solar and Energy Loan Fund Receives $300,000 Community Reinvestment...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Solar and Energy Loan Fund Receives 300,000 Community Reinvestment Act Loan to Invest in Home Energy Upgrades Solar and Energy Loan Fund Receives 300,000 Community Reinvestment ...

  8. Technical evaluation: 300 Area steam line valve accident

    SciTech Connect (OSTI)

    Not Available

    1993-08-01

    On June 7, 1993, a journeyman power operator (JPO) was severely burned and later died as a result of the failure of a 6-in. valve that occurred when he attempted to open main steam supply (MSS) valve MSS-25 in the U-3 valve pit. The pit is located northwest of Building 331 in the 300 Area of the Hanford Site. Figure 1-1 shows a layout of the 300 Area steam piping system including the U-3 steam valve pit. Figure 1-2 shows a cutaway view of the approximately 10- by 13- by 16-ft-high valve pit with its various steam valves and connecting piping. Valve MSS-25, an 8-in. valve, is located at the bottom of the pit. The failed 6-in. valve was located at the top of the pit where it branched from the upper portion of the 8-in. line at the 8- by 8- by 6-in. tee and was then ``blanked off`` with a blind flange. The purpose of this technical evaluation was to determine the cause of the accident that led to the failure of the 6-in. valve. The probable cause for the 6-in. valve failure was determined by visual, nondestructive, and destructive examination of the failed valve and by metallurgical analysis of the fractured region of the valve. The cause of the accident was ultimately identified by correlating the observed failure mode to the most probable physical phenomenon. Thermal-hydraulic analyses, component stress analyses, and tests were performed to verify that the probable physical phenomenon could be reasonably expected to produce the failure in the valve that was observed.

  9. Data summary for nominal 500 ?m DUO2 Kernels

    SciTech Connect (OSTI)

    Hunn, John D

    2004-04-01

    This document is a compilation of characterization data obtained on the nominal 500 {micro}m DUO{sub 2} kernels produced by ORNL for the Advanced Gas Reactor Fuel Development and Qualification Program to satisfy the FY03 WBS 3.1.2 task milestone No.2.2 kg of kernels were produced and combined in two composite lots. DUN-500 was a 1630 g composite sieved between 500 {+-} 2 {micro}m and 534 {+-} 2 {micro}m ASTM E161 electroformed sieves. DUN-482 was a 385.6 g composite sieved between 482 {+-} 2 {micro}m and 518 {+-} 2 {micro}m ASTM E161 electroformed sieves. Size, shape, density, and microstructural analysis were performed on a 100 g sublot (DUN-500-S-1) riffled from the DUN-500 composite. Size and shape were also measured on a 100 g sublot (DUN-482-S-1) riffled from the DUN-482 composite. For comparison, analysis was also performed on kernels extracted from the German reference fuel EUO 2358-2365 (AGR-06).

  10. INDEPENDENT TECHNICAL REVIEW OF THE C-400 INTERIM REMEDIAL PROJECT PHASE I RESULTS, PADUCAH, KENTUCKY

    SciTech Connect (OSTI)

    Looney, B.; Rossabi, J.; Stewart,L.; Richards, W.

    2010-10-29

    The groundwater and soil in the vicinity of the C-400 Building at the Paducah Gaseous Diffusion Plant (PGDP), is contaminated with substantial quantities of industrial solvents, primarily trichoroethene (TCE). This solvent 'source' is recognized as a significant challenge and an important remediation target in the overall environmental cleanup strategy for PGDP. Thus, the cleanup of the C-400 TCE Source is a principal focus for the Department of Energy (DOE) and its contractors, and for PGDP regulators and stakeholders. Using a formal investigation, feasibility study and decision process, Electrical Resistance Heating (ERH) was selected for the treatment of the soil and groundwater in the vicinity of C-400. ERH was selected as an interim action to remove 'a significant portion of the contaminant mass of TCE at the C-400 Cleaning Building area through treatment' with the longer term goal of reducing 'the period the TCE concentration in groundwater remains above its Maximum Contaminant Level (MCL).' ERH is a thermal treatment that enhances the removal of TCE and related solvents from soil and groundwater. The heterogeneous conditions at PGDP, particularly the high permeability regional gravel aquifer (RGA), are challenging to ERH. Thus, a phased approach is being followed to implement this relatively expensive and complex remediation technology. Conceptually, the phased approach encourages safety and efficiency by providing a 'lessons learned' process and allowing appropriate adjustments to be identified and implemented prior to follow-on phase(s) of treatment. More specifically, early deployment targeted portions of the challenging RGA treatment zone with relatively little contamination reducing the risk of adverse collateral impacts from underperformance in terms of heating and capture. Because of the importance and scope of the C-400 TCE source remediation activities, DOE chartered an Independent Technical Review (ITR) in 2007 to assess the C-400 ERH plans prior to deployment and a second ITR to evaluate Phase I performance in September 2010. In this report, these ITR efforts are referenced as the '2007 ITR' and the 'current ITR', respectively. The 2007 ITR document (Looney et al., 2007) provided a detailed technical evaluation that remains relevant and this report builds on that analysis. The primary objective of the current ITR is to provide an expedited assessment of the available Phase I data to assist the PGDP team as they develop the lessons learned from Phase I and prepare plans for Phase II.

  11. Volatile Organic Compound Investigation Results, 300 Area, Hanford Site, Washington

    SciTech Connect (OSTI)

    Peterson, Robert E.; Williams, Bruce A.; Smith, Ronald M.

    2008-07-07

    Unexpectedly high concentrations of volatile organic compounds (VOC) were discovered while drilling in the unconfined aquifer beneath the Hanford Site’s 300 Area during 2006. The discovery involved an interval of relatively finer-grained sediment within the unconfined aquifer, an interval that is not sampled by routine groundwater monitoring. Although VOC contamination in the unconfined aquifer has been identified and monitored, the concentrations of newly discovered contamination are much higher than encountered previously, with some new results significantly higher than the drinking water standards. The primary contaminant is trichloroethene, with lesser amounts of tetrachloroethene. Both chemicals were used extensively as degreasing agents during the fuels fabrication process. A biological degradation product of these chemicals, 1,2-dichloroethene, was also detected. To further define the nature and extent of this contamination, additional characterization drilling was undertaken during 2007. Four locations were drilled to supplement the information obtained at four locations drilled during the earlier investigation in 2006. The results of the combined drilling indicate that the newly discovered contamination is limited to a relatively finer-grained interval of Ringold Formation sediment within the unconfined aquifer. The extent of this contamination appears to be the area immediately east and south of the former South Process Pond. Samples collected from the finer-grained sediment at locations along the shoreline confirm the presence of the contamination near the groundwater/river interface. Contamination was not detected in river water that flows over the area where the river channel potentially incises the finer-grained interval of aquifer sediment. The source for this contamination is not readily apparent. A search of historical documents and the Hanford Waste Information Data System did not provide definitive clues as to waste disposal operations and/or spills that might have resulted in groundwater contamination in this sediment, although several relatively small accidental releases of VOCs have occurred in the past in the northern portion of the 300 Area. It is likely that large quantities of degreasing solutions were disposed to the North and South Process Ponds during the 1950s and 1960s, and that evidence for them in the upper portion of the unconfined aquifer has been removed because of groundwater movement through the much more transmissive sediment. Also, investigations to date have revealed no evidence to suggest that a dense, non-aqueous phase liquid remains undetected in the subsurface. Potential pathways for contamination to migrate from this finer-grained sediment include groundwater movement through the interval to offshore locations in the Columbia River channel, dispersion out of the finer-grained interval into the overlying transmissive sediment (again, with transport to the riverbed), and potential future withdrawal via water supply wells.

  12. 300 Area Treated Effluent Disposal Facility permit reopener run plan

    SciTech Connect (OSTI)

    Olander, A.R.

    1995-03-10

    The 300 Area Treated Effluent Disposal Facility (TEDF) is authorized to discharge treated effluent to the Columbia River by National Pollutant Discharge Elimination System permit WA-002591-7. The letter accompanying the final permit noted the following: EPA recognizes that the TEDF is a new waste treatment facility for which full scale operation and effluent data has not been generated. The permit being issued by EPA contains discharge limits that are intended to force DOE`s treatment technology to the limit of its capability.`` Because of the excessively tight limits the permit contains a reopener clause which may allow limits to be renegotiated after at least one year of operation. The restrictions for reopening the permit are as follows: (1) The permittee has properly operated and maintained the TEDF for a sufficient period to stabilize treatment plant operations, but has nevertheless been unable to achieve the limitation specified in the permit. (2) Effluent data submitted by the permittee supports the effluent limitation modifications(s). (3) The permittee has submitted a formal request for the effluent limitation modification(s) to the Director. The purpose of this document is to guide plant operations for approximately one year to ensure appropriate data is collected for reopener negotiations.

  13. Application for Presidential Permit OE Docket No. PP-400 TDI-NE - New

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    England Clean Power Link Project - Comments and Motion to Intervene of Conservation Law Foundation | Department of Energy Project - Comments and Motion to Intervene of Conservation Law Foundation Application for Presidential Permit OE Docket No. PP-400 TDI-NE - New England Clean Power Link Project - Comments and Motion to Intervene of Conservation Law Foundation Conservation Law Foundation (CLF) provides the following comments and Motion to Intervene regarding the Application by TDI-New

  14. Turbines Off NYC East River Will Provide Power to 9,500 Residents |

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Department of Energy Turbines Off NYC East River Will Provide Power to 9,500 Residents Turbines Off NYC East River Will Provide Power to 9,500 Residents February 6, 2012 - 3:16pm Addthis Free Flow System turbine being installed in East River, New York, NY (Dec 2006). | Image Credit: Kris Unger/Verdant Power, Inc. Free Flow System turbine being installed in East River, New York, NY (Dec 2006). | Image Credit: Kris Unger/Verdant Power, Inc. Hoyt Battey Market Acceleration and Deployment

  15. EIS-0107: Mead-Phoenix +500-kV Direct Current Transmission Line

    Broader source: Energy.gov [DOE]

    The U.S. Department of Energy’s Western Area Power Administration (WAPA) prepared this statement to analyze the potential environmental and socioeconomic impacts arising from WAPA and regional project sponsors’ proposal to construct a 500 kilovolt (kV) alternating current (AC) transmission line with the capability to be upgraded later to 500kV direct current (DC), connecting the Westwing Substation, located north of Phoenix, Arizona, with a new McCullough II Substation, located approximately 14 miles west of Boulder City, Nevada. This statement modifies a previously prepared federal statement from which the participants' election to proceed had not occurred at the time this statement was prepared.

  16. Use of Static Compensators for Voltage Control at 330- and 500-kV Substations

    SciTech Connect (OSTI)

    Dement'ev, Yu. A.; Kochkin, V. I.; Idiatullov, R. M.; Papafanasopulo, S. G.; Smirnov, A. A.; Smirnov, S. G.

    2003-05-15

    A scheme for compensating the reactive power and controlling the voltage of high-voltage, intermediate-voltage, and low-voltage buses of 330 - 500-kV substations, which consist of static thyristor compensators (STC) on low-voltage autotransformers and controlled shunting reactors on high-voltage lines, is presented. It is shown that the STC can be created step-by-step beginning with the reactive part on substations with low-loaded lines. Results of installation of reactor groups of STC stepwise-controlled by vacuum switches at 330- and 500-kV substations are presented. Tests of the reactor groups have proved their high efficiency.

  17. Y-12 has almost 500 visitors from 23 states tour site during Secret City

    National Nuclear Security Administration (NNSA)

    Festival | National Nuclear Security Administration has almost 500 visitors from 23 states tour site during Secret City Festival Wednesday, June 25, 2014 - 3:34pm NNSA Blog B&W Y-12 employee and tour guide Bill Wilburn, left, chats with Teresa Neas, and her husband Kim, whose mother, Audeane Bowers-Neas, worked at Y-12 in the 1940s. Tours of Y-12 on June 13 brought almost 500 visitors. Tourists from 23 states and the District of Columbia toured the site as part of Oak Ridge's 12th

  18. Proposed amendment for Presidential Permit PP-63 and associated modifications to 500 kV international transmission line, Forbes, Minnesota to Manitoba, Canada Northern States Power Company. Final Environmental Assessment

    SciTech Connect (OSTI)

    Not Available

    1992-02-01

    Northern States Power Company, (NSP), a Minnesota investor owned utility has applied to the Office of Fossil Energy, United States Department of Energy, to amend Presidential Permit PP-63 to allow for alterations to the 500 kV transmission line and as sedated facilities currently regulated by this permit. The alterations proposed for the 500 kV line owned by NSP are part of a long term effort sponsored by NSP to upgrade the existing NSP transmission system to allow for increased exchange of electricity with the Manitoba Hydro-Electric Board. Presidential Permit PP-63 authorized NSP to construct, connect, operate and maintain a 500 kV line at the United States/Canadian border approximately seven-and-a-half miles west of Warroad in Roseau County, Minnesota. This line connects with a 500 kV line owned and operated by the Manitoba Hydro-Electric Board (MHEB), which extends from Dorsey, Manitoba, Canada to the United States/Canadian border. NSP proposes to increase the electricity transfer capability of this transmission facility by constructing a new 80-acre substation on the existing 500 kV line in Roseau County, Minnesota, and upgrading the existing substation at Forbes, Minnesota. The proposed Roseau substation would contain two 41.5 ohm series capacitor banks. In addition, static VAR compensators are to be installed at the existing Forbes Substation. Approximately 5 acres would be added to the 30-acre Forbes site to house the additional equipment. No new lines would enter or exit the facility. NSP proposes to place the new Roseau Substation in service in May 1993 and to complete the upgrading of the Forbes Substation in March 1994. The primary, initial purpose of these modifications is to enable NSP to import 400 megawatts of electric power from MHEB during the summer months to meet peak electrical demand in the Minneapolis-St. Paul area. It is expected that this power transfer would begin in 1993.

  19. A High Temperature (400 to 650oC) Secondary Storage Battery Based on Liquid Sodium and Potassium Anodes

    SciTech Connect (OSTI)

    Tao, Greg; Weber, Neill

    2007-06-08

    This STTR Phase I research program was on the development of high temperature (400 to 650 C), secondary batteries with roundtrip efficiency > 90% for integration with a 3 to 10 kW solid oxide fuel cell (SOFC) system. In fulfillment of this objective, advanced planar high temperature rechargeable batteries, comprised of an alkali metal ion conducting, highly refractory, beta'' alumina solid electrolyte (BASE) sandwiched between liquid sodium (or potassium) anode and liquid metal salt cathode, were developed at MSRI. The batteries have been successfully demonstrated at a working temperature as high as 600 C. To our knowledge, so far no work has been reported in the literature on planar rechargeable batteries based on BASE, and results obtained in Phase I for the very first time demonstrated the viability of planar batteries, though relatively low temperature tubular-based sodium-sulfur batteries and ZEBRA batteries have been actively developed by very limited non U.S. companies. The results of this Phase I work have fulfilled all the goals and stated objectives, and the achievements showed much promise for further, substantial improvements in battery design and performance. The important results of Phase I are briefly described in what follows: (1) Both Na-BASE and K-BASE discs and tubes have been successfully fabricated using MSRI's patented vapor phase process. Ionic conductivity measurements showed that Na-BASE had higher ionic conductivity than K-BASE, consistence with the literature. At 500 C, Na-BASE conductivity is 0.36 S/cm, which is more than 20 times higher than 8YSZ electrolyte used for SOFC at 800 C. The activation energy is 22.58 kJ/mol. (2) CuCl{sub 2}, FeCl{sub 2}, ZnCl{sub 2}, and AgCl were identified as suitable salts for Na/metal salt or K/metal salt electrochemical couples based on thermochemical data. Further open circuit voltage measurements matched those deduced from the thermochemical data. (3) Tubular cells with CuCl{sub 2} as the cathode and Na as the anode were constructed. However, it was discovered that CuCl{sub 2} was somewhat corrosive and dissolved iron, an element of the cathode compartment. Since protective coating technology was beyond this Phase I work scope, no further work on the CuCl{sub 2} cathode was pursued in Phase I. Notwithstanding, due to its very high OCV and high specific energy, CuCl{sub 2} cathode is a very attractive possibility for a battery capable of delivering higher specific energy with higher voltage. Further investigation of the Na-CuCl{sub 2} battery can be done by using suitable metal coating technologies developed at MSRI for high temperature applications. (4) In Phase I, FeCl{sub 2} and ZnCl{sub 2} were finalized as the potential cathodes for Na-metal salt batteries for delivering high specific energies. Planar Na-FeCl{sub 2} and Na-ZnCl{sub 2} cells were designed, constructed, and tested between 350 and 600 C. Investigation of charge/discharge characteristics showed they were the most promising batteries. Charge/discharge cycles were performed as many as 27 times, and charge/discharge current was as high as 500 mA. No failure was detected after 50 hours testing. (5) Three-cell planar stacks were designed, constructed, and evaluated. Preliminary tests showed further investigation was needed for optimization. (6) Freeze-thaw survival was remarkably good for planar BASE discs fabricated by MSRI's patented vapor phase process.

  20. EIS-0118: Proposed Eugene-Medford 500-kV Transmission Line

    Broader source: Energy.gov [DOE]

    The U.S. Department of Interior developed this statement to assess the environmental impact of a proposed 500-kilovolt transmission line linking Eugene and Medford, Oregon, that would cross through public lands. The Bonneville Power Administration (BPA) would provide service to the proposed line and is a cooperating agency in the statement. BPA adopted the EIS on 7/10/1985.

  1. Scalar Meson {sigma}(500) Phase Motion at D+ {yields} {pi}-{pi}+{pi}+ Decay

    SciTech Connect (OSTI)

    Miranda, Jussara M. de; Bediaga, Ignacio

    2006-02-11

    Applying the Amplitude Difference Method to Fermilab experiment E791 D+ {yields} {pi}-{pi}+{pi}+ data, we measure the low mass {pi}+{pi}- phase motion. Our results suggest a significant phase variation, compatible with the existence of an isoscalar {sigma}(500) meson, as previously reported using an isobar model fit to the full Dalitz-plot density.

  2. The Case for a 500 GeV e+e- Linear Collider

    SciTech Connect (OSTI)

    Baggers, J.; Baltay, C.; Barker, T.; Barklow, T.; Bauer, U.; Bolton, T.; Brau, J.; Breidenbach, M.; Burke, D.; Burrows, P.; Dixon, L.; Fisk, H.E.; Frey, R.; Gerdes, D.; Graf, D.; Grannis, P.; Haber, H.E.; Hearty, C.; Hertzbach, S.; Heusch, C.; Hewett, J.; Hollebeek, R.; Jacobsen, R.; Jaros, J.; Kamon, T.; Karlen, D.; Koltick, D.; Kronfeld, A.; Marciano, W.; Markiewicz, T.; Murayama, H.; Nauenberg, U.; Orr, L.; Paige, F.; Para, A.; Peskin, M. E.; Porter, F.; Riles, K.; Ronan, M.; Rosenberg, L.; Schumm, B.; Stroynowski, R.; Tkaczyk, S.; Turcot, A.S.; van Bibber, K.; van Kooten, R.; Wells, J.D.; Yamamoto, H.

    2000-07-05

    Several proposals are being developed around the world for an e+e- linear collider with an initial center of mass energy of 500 GeV. In this paper, we will discuss why a project of this type deserves priority as the next major initiative in high energy physics.

  3. Lattice QCD Thermodynamics : 10k analysis with 1k thermalziation and block size of 500.

    SciTech Connect (OSTI)

    Soltz, R; Vranas, P; Gupta, R

    2007-05-10

    This is a re-analysis of the Lattice QCD Thermodynamics p4rhcm new beta analysis (UCRL-TR-230742) with approximately 10k trajectories per beta point, rerun with thermalization cut at 1000, and a block size of 500. Some diagnostic text has been omitted to reduce the number of pages.

  4. Residual Nuclei Production in the reaction {sup 136}Xe+ deuterium at 500 A MeV

    SciTech Connect (OSTI)

    Alcantara-Nunez, J. A.; Benlliure, J.; Perez-Loureiro, D.; Casarejos, E.; Fernandez Ordonez, M.; Pereira, J.; Armbruster, P.; Enqvist, T.; Henzl, V.; Henzlova, D.; Kelic, A.; Pleskac, R.; Ricciardi, M. V.; Schmidt, K.-H.; Schmitt, C.; Yordanov, O.; Audouin, L.; Bernas, M.; Lafriaskh, A.; Stephan, C.

    2010-04-26

    More than six hundred nuclei produced in the fragmentation of {sup 136}Xe projectiles at 500 A MeV on a liquid deuterium target were identified using inverse kinematics at the GSI Fragment Separator (FRS). These data are relevant for understanding of spallation reactions.

  5. THE CASE FOR A 500 GEV E+E- LINEAR COLLIDER

    SciTech Connect (OSTI)

    BAGGER,J.; BALTAY,C.; ET AL; MARCIANO,W.; PAIGE,F.; TURCOT,A.S.; AMERICAN LINEAR COLLIDER WORKING GROUP

    2000-06-30

    There are now several proposals that have been put forward from around the world for an e{sup +}e{sup {minus}} linear collider with an initial center of mass energy of 500 GeV. In this paper, the authors discuss why a project of this type deserves priority as the next, major initiative in high energy physics.

  6. Application for presidential permit OE Docket No. PP-300 Maine Public

    Energy Savers [EERE]

    Service Company | Department of Energy 0 Maine Public Service Company Application for presidential permit OE Docket No. PP-300 Maine Public Service Company Applicationfrom Maine Public Service Company to construct, operate, and maintain electric transmission facilities at the U.S-Canada border. PDF icon Application for presidential permit OE Docket No. PP-300 Maine Public Service Company More Documents & Publications PP-300 Maine Public Service Company EA-1945: Draft Environmental

  7. On Earth Day Vice President Biden Announces $300 Million in Recovery Act

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Funds for Clean Cities Program | Department of Energy On Earth Day Vice President Biden Announces $300 Million in Recovery Act Funds for Clean Cities Program On Earth Day Vice President Biden Announces $300 Million in Recovery Act Funds for Clean Cities Program April 22, 2009 - 12:00am Addthis LANDOVER, MD - During a visit to the WMATA Carmen Turner Maintenance and Training Facility in Landover, MD, Vice President Joe Biden today announced $300 million in funding from the American Recovery

  8. Uranium Geochemistry in Vadose Zone and Aquifer Sediments from the 300 Area Uranium Plume

    SciTech Connect (OSTI)

    Zachara, John M.; Davis, Jim A.; Liu, Chongxuan; McKinley, James P.; Qafoku, Nik; Wellman, Dawn M.; Yabusaki, Steven B.

    2005-07-21

    This report documents research conducted by the RCS Project to update the record of decision for the 300-FF-5 Operable Unit on the Hanford Site.

  9. Ubiquitination of Notch1 is regulated by MAML1-mediated p300 acetylation of Notch1

    SciTech Connect (OSTI)

    Popko-Scibor, Anita E.; Lindberg, Mikael J.; Hansson, Magnus L.; Holmlund, Teresa; Wallberg, Annika E.

    2011-12-16

    Highlights: Black-Right-Pointing-Pointer p300 acetylates conserved lysines within Notch1 C-terminal nuclear localization signal. Black-Right-Pointing-Pointer MAML1 and CSL, components of Notch transcription complex, increase Notch acetylation. Black-Right-Pointing-Pointer MAML1-dependent acetylation of Notch1 by p300 decreases the ubiquitination of Notch1. Black-Right-Pointing-Pointer CDK8 inhibits Notch acetylation and Notch transcription enhanced by p300. -- Abstract: Earlier studies demonstrated the involvement of the p300 histone acetyltransferase in Notch signaling but the precise mechanisms by which p300 might modulate Notch function remains to be investigated. In this study, we show that p300 acetylates Notch1 ICD in cell culture assay and in vitro, and conserved lysines located within the Notch C-terminal nuclear localization signal are essential for Notch acetylation. MAML1 and CSL, which are components of the Notch transcription complex, enhance Notch acetylation and we suggest that MAML1 increases Notch acetylation by potentiating p300 autoacetylation. Furthermore, MAML1-dependent acetylation of Notch1 ICD by p300 decreases the ubiquitination of Notch1 ICD in cellular assays. CDK8 has been shown to target Notch1 for ubiquitination and proteosomal degradation. We show that CDK8 inhibits Notch acetylation and Notch transcription enhanced by p300. Therefore, we speculate that acetylation of Notch1 might be a mechanism to regulate Notch activity by interfering with ubiquitin-dependent pathways.

  10. H.A.R. 13-300 - Rules of Practice and Procedure Relating to Burial...

    Open Energy Info (EERE)

    300 - Rules of Practice and Procedure Relating to Burial Sites and Human Remains Jump to: navigation, search OpenEI Reference LibraryAdd to library Legal Document-...

  11. 300 AREA PACIFIC NORTHWEST NATIONAL LABORATORY FACILITY RADIONUCLIDE EMISSION POINTS AND SAMPLING SYSTEMS

    SciTech Connect (OSTI)

    Barfuss, Brad C.; Barnett, J. M.; Harbinson, L Jill

    2006-08-28

    Radionuclide emission points for 300 Area and Battelle Private facilities are presented herein. The sampling systems and associated emission specifics are detailed.

  12. Department of Energy Awards $300,000 Block Grant to the Rocky...

    Broader source: Energy.gov (indexed) [DOE]

    Block Grant to the Rocky Flats Community Reuse Organization Department of Energy Awards 300,000 Block Grant to the Rocky Flats Community Reuse Organization More Documents &...

  13. 300 Area D4 Project Fiscal Year 2010 Building Completion Report

    SciTech Connect (OSTI)

    Skwarek, B. J.

    2011-01-27

    This report summarizes the deactiviation, decontamination, decommissioning, and demolition activities of facilities in the 300 Area of the Hanford Site in fiscal year 2010.

  14. Volume Reflection Dependence of 400 GeV/c Protons on the Bent Crystal Curvature

    SciTech Connect (OSTI)

    Scandale, W.; Vomiero, A.; Baricordi, S.; Dalpiaz, P.; Fiorini, M.; Guidi, V.; Mazzolari, A.; Milan, R.; Della Mea, Gianantonio; Ambrosi, G.; Zuccon, P.; Bertucci, B.; Burger, W. J.; Duranti, M.; Cavoto, G.; Santacesaria, R.; Valente, P.; Iacoangeli, F.; Pisano, S.; Luci, C.

    2008-12-05

    The trend of volume reflection parameters (deflection angle and efficiency) in a bent (110) silicon crystal has been investigated as a function of the crystal curvature with 400 GeV/c protons on the H8 beam line at the CERN Super Proton Synchrotron. This Letter describes the analysis performed at six different curvatures showing that the optimal radius for volume reflection is approximately 10 times greater than the critical radius for channeling. A strong scattering of the beam by the planar potential is also observed for a bend radius close to the critical one.

  15. PDSF Office Hours 1/23/14 from 2:30 to 4:00 pm at LBNL

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    /23/14 from 2:30 to 4:00 pm at LBNL PDSF Office Hours 1/23/14 from 2:30 to 4:00 pm at LBNL January 22, 2014 PDSF office hours will be from 2:30 to 4:00 pm in 50B-2222 tomorrow. Subscribe via RSS Subscribe Browse by Date February 2014 January 2014 November 2013 October 2013 September 2013 August 2013 March 2012 February 2012 January 2012 October 2011 July 2011 May 2011 April 2011 March 2011 February 2011 January 2011 December 2010 Last edited: 2014-01-22 16:33:02

  16. 17th Edition of TOP500 List of World's Fastest SupercomputersReseased

    SciTech Connect (OSTI)

    Strohmaier, Erich; Meuer, Hans W.; Dongarra, Jack J.; Simon,Horst D.

    2001-06-21

    17th Edition of TOP500 List of World's Fastest Supercomputers Released MANNHEIM, GERMANY; KNOXVILLE, TENN.; BERKELEY, CALIF. In what has become a much-anticipated event in the world of high-performance computing, the 17th edition of the TOP500 list of the world's fastest supercomputers was released today (June 21). The latest edition of the twice-yearly ranking finds IBM as the leader in the field, with 40 percent in terms of installed systems and 43 percent in terms of total performance of all the installed systems. In second place in terms of installed systems is Sun Microsystems with 16 percent, while Cray Inc. retained second place in terms of performance (13 percent). SGI Inc. was third both with respect to systems with 63 (12.6 percent) and performance (10.2 percent).

  17. Non-ordinary nature of the f_0(500) resonance from its Regge trajectory

    SciTech Connect (OSTI)

    Nebreda, J.; Londergan, J. Timothy; Pelaez, J. R.; Szczepaniak, Adam P.

    2014-07-01

    We report our results on how to obtain the Regge trajectory of a resonance from its pole in a scattering process by imposing analytic constraints in the complex angular momentum plane. The method, suited for resonances that dominate an elastic scattering amplitude, has been applied to the {\\rho}(770) and the f_0(500) resonances. Whereas for the former we obtain a linear Regge trajectory, characteristic of ordinary quark-antiquark states, for the latter we find a non-linear trajectory with a much smaller slope at the resonance mass. Moreover, we show that if a linear trajectory with a slope of typical size is imposed for the f_0(500), the corresponding amplitude is at odds with the data. This provides a strong indication of the non-ordinary nature of the sigma meson.

  18. Ion-induced swelling of ODS ferritic alloy MA957 tubing to 500 dpa

    SciTech Connect (OSTI)

    Toloczko, Mychailo B.; Garner, F. A.; Voyevodin, V.; Bryk, V. V.; Borodin, O. V.; Melnichenko, V. V.; Kalchenko, A. S.

    2014-10-01

    In order to study the potential swelling behavior of the ODS ferritic alloy MA957 at very high dpa levels, specimens were prepared from pressurized tubes that were unirradiated archives of tubes previously irradiated in FFTF to doses as high at 110 dpa. These unirradiated specimens were irradiated with 1.8 MeV Cr+ ions to doses ranging from 100 to 500 dpa and examined by transmission electron microscopy. No coinjection of helium or hydrogen was employed. It was shown that compared to several ferritic/martensitic steels irradiated in the same facility, these tubes were rather resistant to void swelling, reaching a maximum value of only 4.5% at 500 dpa and 450°C. In this fine-grained material, the distribution of swelling was strongly influenced by the presence of void denuded zones along the grain boundaries.

  19. Irradiation creep of various ferritic alloys irradiated {approximately}400 C in the PFR and FFTF reactors

    SciTech Connect (OSTI)

    Toloczko, M.B.; Garner, F.A.; Eiholzer, C.R.

    1998-03-01

    Three ferritic alloys were irradiated in two fast reactors to doses of 50 dpa or more at temperatures near 400 C. One martensitic alloy, HT9, was irradiated in both the FFTF and PFR reactors. PFR is the Prototype Fast Reactor in Dourneay, Scotland, and FFTF is the Fast Flux Test Facility in Richland, WA. D57 is a developmental alloy that was irradiated in PFR only, and MA957 is a Y{sub 2}O{sub 3} dispersion-hardened ferritic alloy that was irradiated only in FFTF. These alloys exhibited little or no void swelling at {approximately}400 C. Depending on the alloy starting condition, these steels develop a variety of non-creep strains early in the irradiation that are associated with phase changes. Each of these alloys creeps at a rate that is significantly lower than that of austenitic steels irradiated in the same experiments. The creep compliance for ferritic alloys in general appears to be {approximately}0.5 {times} 10{sup {minus}6} MPa{sup {minus}1} dpa{sup {minus}1}, independent of both composition and starting state. The addition of Y{sub 2}O{sub 3} as a dispersoid does not appear to change the creep behavior.

  20. EIS-0091: Garrison-Spokane 500-kV Transmission Project

    Broader source: Energy.gov [DOE]

    The U.S. Department of Energy's Bonneville Power Administration (BPA) developed this statement to evaluate the environmental impacts of constructing between 254 and 271 miles of 500-kilovolt transmission line across western Montana and northern Idaho to the Spokane area in order to reinforce a section of the BPA electric power grid and to permit reliable integration of 1,240 megawatts of power produced by Colstrip Units 3 and 4, for use in Montana and throughout the Northwest.

  1. SEARCHING FOR THE HIGHEST REDSHIFT SOURCES IN 250-500 {mu}m SUBMILLIMETER SURVEYS

    SciTech Connect (OSTI)

    Pope, Alexandra; Chary, Ranga-Ram

    2010-06-01

    We explore a technique for identifying the highest redshift (z>4) sources in Herschel/SPIRE and BLAST submillimeter surveys by localizing the position of the far-infrared dust peak. Just as Spitzer/IRAC was used to identify stellar 'bump' sources, the far-IR peak is also a redshift indicator; although the latter also depends on the average dust temperature. We demonstrate the wide range of allowable redshifts for a reasonable range of dust temperatures and show that it is impossible to constraint the redshift of individual objects using solely the position of the far-IR peak. By fitting spectral energy distribution models to simulated Herschel/SPIRE photometry we show the utility of radio and/or far-infrared data in breaking this degeneracy. With prior knowledge of the dust temperature distribution it is possible to obtain statistical samples of high redshift submillimeter galaxy (SMG) candidates. We apply this technique to the BLAST survey of ECDFS to constrain the number of dusty galaxies at z>4. We find 8 {+-} 2 galaxies with flux density ratios of S {sub 500}>S {sub 350}; this sets an upper limit of 17 {+-} 4 deg{sup -2} if we assume all are at z>4. This is <35 % of all 500 {mu}m-selected galaxies down to S {sub 500}>45 mJy (L {sub IR}>2 x 10{sup 13} L {sub sun} for z>4). Modeling with conventional temperature and redshift distributions estimates the percentage of these 500 {mu}m peak galaxies at z>4 to be between 10% and 85%. Our results are consistent with other estimates of the number density of very high redshift SMGs and follow the decline in the star formation rate density at z>4.

  2. EIS-0301: NRG Energy Services, Inc., Arizona-Baja California 500 kV Transmission Line

    Broader source: Energy.gov [DOE]

    This EIS analyzes DOE's decision to approve NRG Energy, Inc. (NRG) for a Presidential permit to construct a 500,000-volt transmission line originating at the switchyard of the Palo Verde Nuclear Generating Station near Phoenix, Arizona, and extending approximately 177 miles to the southwest, where it would cross the United States (U.S.) border with Mexico in the vicinity of Calexico, California.

  3. ATP for the portable 500 CFM exhauster POR-005 skid C

    SciTech Connect (OSTI)

    Keller, C.M.

    1997-06-27

    This Acceptance Test Plan is for a 500 CFM Portable Exhauster POR-005 to be used for saltwell pumping. The Portable Exhauster System will be utilized to eliminate potential flammable gases that may exist within the dome space of the tank. This Acceptance Plan will test and verify that the exhauster meets the specified design criteria, safety requirements, operations requirements, and will provide a record of the functional test results.

  4. ATP for the portable 500 CFM exhauster POR-004 skid B

    SciTech Connect (OSTI)

    Keller, C.M.

    1997-05-06

    This Acceptance Test Plan is for a 500 CFM Portable Exhauster POR-004 to be used for saltwell pumping. The Portable Exhauster System will be utilized to eliminate potential flammable gases that may exist within the dome space of the tank. This Acceptance Plan will test and verify that the exhauster meets the specified design criteria, safety requirements, operations requirements, and will provide a record of the functional test results.

  5. ATP for the portable 500 CFM exhauster POR-006 skid D

    SciTech Connect (OSTI)

    Keller, C.M.

    1997-07-29

    This Acceptance Test Plan is for a 500 CFM Portable Exhauster POR-006 to be used for saltwell pumping. The Portable Exhauster System will be utilized to eliminate potential flammable gases that may exist within the dome space of the tank. This Acceptance Plan will test and verify that the exhauster meets the specified design criteria, safety requirements, operations requirements, and will provide a record of the functional test results.

  6. Precipitation hardening in nickel-copper base alloy Monel K 500

    SciTech Connect (OSTI)

    Dey, G.K.; Tewari, R.; Wadekar, S.L.; Mukhopadhyay, P.; Rao, P.

    1993-12-01

    The occurrence of a significant amount of age hardening, due to the precipitation of the {gamma}{prime} phase, has been demonstrated in the nickel-copper base alloy MONEL K 500. The microstructure of the precipitation-hardened and deformed alloy has been examined in peak-aged, underaged and overaged conditions. An attempt has been made to compare the observed increments in strength in these three aged conditions to those predicted on the basis of relevant theoretical models.

  7. A Study of Electromagnetic Radiation of Corona Discharge Near 500-Kv Electric Installations

    SciTech Connect (OSTI)

    Korzhov, A. V.; Okrainskaya, I. S.; Sidorov, A. I.; Kufel'd, V. D.

    2004-01-15

    Data on the spectral composition and intensity of electromagnetic radiation of corona discharge are obtained in an experimental study performed on the outdoor switchgear of the Shagol 500-kV substation of the Chelyabinsk Enterprise of Trunk Transmission Grids and under a 500-kV Shagol - Kozyrevo overhead transmission line. The electromagnetic environment on the territory of the 500-kV outdoor switchgear is shown to be determined by narrow-band radiations (harmonics of the frequency of electric supply) and wide-band radiations due to corona discharges of high-voltage sources. This means that the personnel experience the action of a commercial-frequency electric field and electromagnetic radiation of a quite wide range, which is not allowed for by the existing guidelines. It is recommended to continue the study in cooperation with medical institutions in order to create guidelines that would allow for the joint action of commercial-frequency electric field and electromagnetic radiation and for the voltage in the line, the current load, the meteorological situation, and other factors.

  8. Specification for strontium-90 500-watt(e) radioisotopic thermoelectric generator. Final report

    SciTech Connect (OSTI)

    Hammel, T.; Himes, J.; Lieberman, A.; McGrew, J.; Owings, D.; Schumann, F.

    1983-04-01

    A conceptual design for a demonstration 500-watt(e) radioisotopic thermoelectric generator has been created for the Department of Energy. The design effort was divided into two tasks, viz., create a design specification for a capsule strength member that utilizes a standard Strontium-90 fluoride-filled WESF inner liner, and create a conceptual design for a 500-watt(e) RTG. Both tasks have been accomplished. The strength-member specification was designed to survive an external pressure of 24,500 psi and meet the requirements of special-form radioisotope heat sources. Therefore the capsule can, if desired, be licensed for domestic and international transport. The design for the RTG features a radioisotopic heat source, an array of nine capsules in a tungsten biological shield, four current-technology series-connected thermoelectric-conversion modules, low-conductivity thermal insulation, and a passive finned-housing radiator for waste-heat dissipation. The preliminary RTG specification formulated previous to contract award has been met or exceeded. The power source will generate the required power for the required service period at 28 volts dc with a conversion efficiency of 8%, provided the existing in-pool capsules at WESF meet the assumed thermal-inventory requirements.

  9. Three-Dimensional Groundwater Models of the 300 Area at the Hanford Site, Washington State

    SciTech Connect (OSTI)

    Williams, Mark D.; Rockhold, Mark L.; Thorne, Paul D.; Chen, Yousu

    2008-09-01

    Researchers at Pacific Northwest National Laboratory developed field-scale groundwater flow and transport simulations of the 300 Area to support the 300-FF-5 Operable Unit Phase III Feasibility Study. The 300 Area is located in the southeast portion of the U.S. Department of Energys Hanford Site in Washington State. Historical operations involving uranium fuel fabrication and research activities at the 300 Area have contaminated engineered liquid-waste disposal facilities, the underlying vadose zone, and the uppermost aquifer with uranium. The main objectives of this research were to develop numerical groundwater flow and transport models to help refine the site conceptual model, and to assist assessment of proposed alternative remediation technologies focused on the 300 Area uranium plume.

  10. Fact #757: December 10, 2012 The U.S. Manufactures More Light...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Five States - Missouri, Texas, South Carolina, Minnesota and Louisiana - manufactured ... Michigan 685,300 1,228,200 1,913,500 Minnesota 0 97,200 97,200 Mississippi 170,400 ...

  11. Word Pro - Untitled1

    U.S. Energy Information Administration (EIA) Indexed Site

    prior to 1969. Source: Table 7.2. 19501960 1970 1980 1990 2000 2010 0 300 600 900 1,200 1,500 Million Short Tons Bituminous Coal 19501960 1970 1980 1990 2000 2010 0 200 400 ...

  12. Word Pro - Untitled1

    U.S. Energy Information Administration (EIA) Indexed Site

    Japan 1960 1965 1970 1975 1980 1985 1990 1995 2000 2005 2010 0 100 200 300 400 500 600 Thousand Barrels per Day Exports to Canada and Mexico 1960 1965 1970 1975 1980 1985 1990 1995 ...

  13. Denison Dam Historical Generation

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    50,000 100,000 150,000 200,000 250,000 300,000 350,000 400,000 450,000 500,000 (MWh) Denison Dam Historical Generation

  14. C:\\ANNUAL\\Vol2chps.v8\\ANNUAL2.VP

    U.S. Energy Information Administration (EIA) Indexed Site

    in the United States, 1930-2000 Figure 1930 1935 1940 1945 1950 1955 1960 1965 1970 1975 1980 1985 1990 1995 2000 0 5 10 15 20 25 0 100 200 300 400 500 600 700 Trillion Cubic...

  15. Development of a Scale Model for High Flux Isotope Reactor Cycle 400

    SciTech Connect (OSTI)

    Ilas, Dan

    2012-03-01

    The development of a comprehensive SCALE computational model for the High Flux Isotope Reactor (HFIR) is documented and discussed in this report. The SCALE model has equivalent features and functionality as the reference MCNP model for Cycle 400 that has been used extensively for HFIR safety analyses and for HFIR experiment design and analyses. Numerical comparisons of the SCALE and MCNP models for the multiplication constant, power density distribution in the fuel, and neutron fluxes at several locations in HFIR indicate excellent agreement between the results predicted with the two models. The SCALE HFIR model is presented in sufficient detail to provide the users of the model with a tool that can be easily customized for various safety analysis or experiment design requirements.

  16. Molecular dynamics for 400 million particles with short-range interactions

    SciTech Connect (OSTI)

    Deng, Y.; McCoy, R.A.; Marr, R.B.

    1995-07-01

    We report the design and performance of a computational molecular dynamics (MD) code for 400 million particles interacting through the standard pairwise 6-12 Lennard-Jones potential on a 1024-node Intel Paragon, a distributed-memory MIMD parallel computer. The initially recorded {open_quotes}particle-step time{close_quotes} was .4 microseconds. A new inter-node communication strategy ensures high parallel efficiency for a large number of nodes. Besides the ability to tackle large problems, our implementation incorporates a novel method for dynamic load balancing. Our communication and load balancing enhancements provide increased efficiency and flexibility for our MD code. vet are general enough for use in other parallel algorithms.

  17. Test of a 1.8 Tesla, 400 Hz Dipole for a Muon Synchrotron

    SciTech Connect (OSTI)

    Summers, D.J.; Cremaldi, L.M.; Hart, T.L.; Perera, L.P.; Reep, M.; /Mississippi U.; Witte, H.; /Brookhaven; Hansen, S.; Lopes, M.L.; /Fermilab; Reidy Jr., J.; /Oxford High School

    2012-05-01

    A 1.8 T dipole magnet using thin grain oriented silicon steel laminations has been constructed as a prototype for a muon synchrotron ramping at 400 Hz. Following the practice in large 3 phase transformers and our own Opera-2d simulations, joints are mitred to take advantage of the magnetic properties of the steel which are much better in the direction in which the steel was rolled. Measurements with a Hysteresigraph 5500 and Epstein frame show a high magnetic permeability which minimizes stored energy in the yoke allowing the magnet to ramp quickly with modest voltage. Coercivity is low which minimizes hysteresis losses. A power supply with a fast Insulated Gate Bipolar Transistor (IGBT) switch and a capacitor was constructed. Coils are wound with 12 gauge copper wire. Thin wire and laminations minimize eddy current losses. The magnetic field was measured with a peak sensing Hall probe.

  18. Response of 9Cr-ODS Steel to Proton Irradiation at 400 °C

    SciTech Connect (OSTI)

    Jianchao He; Farong Wan; Kumar Sridharan; Todd R. Allen; A. Certain; Y. Q. Wu

    2014-09-01

    The stability of Y–Ti–O nanoclusters, dislocation structure, and grain boundary segregation in 9Cr-ODS steels has been investigated following proton irradiation at 400 °C with damage levels up to 3.7 dpa. A slight coarsening and a decrease in number density of nanoclusters were observed as a result of irradiation. The composition of nanoclusters was also observed to change with a slight increase of Y and Cr concentration in the nanoclusters following irradiation. Size, density, and composition of the nanoclusters were investigated as a function of nanocluster size, specifically classified to three groups. In addition to the changes in nanoclusters, dislocation loops were observed after irradiation. Finally, radiation-induced enrichment of Cr and depletion of W were observed at grain boundaries after irradiation.

  19. NEUTRON-INDUCED SWELLING OF Fe-Cr BINARY ALLOYS IN FFTF AT ~400 DEGREES C

    SciTech Connect (OSTI)

    Garner, Francis A.; Greenwood, Lawrence R.; Okita, Taira; Sekimura, Naoto; Wolfer, W. G.

    2002-12-31

    The purpose of this effort is to determine the influence of dpa rate, He/dpa ratio and composition on the void swelling of simple binary Fe-Cr alloys. Contrary to the behavior of swelling of model fcc Fe-Cr-Ni alloys irradiated in the same FFTF-MOTA experiment, model bcc Fe-Cr alloys do not exhibit a dependence of swelling on dpa rate at approximately 400 degrees C. This is surprising in that an apparent flux-sensitivity was observed in an earlier comparative irradiation of Fe-Cr binaries conducted in EBR-II and FFTF. The difference in behavior is ascribed to the higher helium generation rates of Fe-Cr alloys in EBR-II compared to that of FFTF, and also the fact that lower dpa rates in FFTF are accompanied by progressively lower helium generation rates.

  20. Secretary Chu Announces Major New Recovery Act Milestone: 300,000 Homes

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Weatherized | Department of Energy Major New Recovery Act Milestone: 300,000 Homes Weatherized Secretary Chu Announces Major New Recovery Act Milestone: 300,000 Homes Weatherized January 19, 2011 - 12:00am Addthis WASHINGTON - U.S. Department of Energy Secretary Steven Chu today announced that states and territories across the country have now weatherized more than 300,000 low-income homes under the Recovery Act, a major milestone in the Department's efforts to reduce home energy bills for

  1. Mr. R. B. Bell, Jr. Combustion Engineering, Inc. Post Office Box 500

    Office of Legacy Management (LM)

    g@ *tq 47 e "Y q$ . -0 t: 2 ~ i' ,; B 0 e %d&$ Department of Energy Washington, DC 20585 Mr. R. B. Bell, Jr. Combustion Engineering, Inc. Post Office Box 500 Windsor, Connecticut 06095-0500 Dear Mr. Bell: I have received two copies of the access agreement for the radiological survey of the Combustion Engineering Property at 1000 Prospect Hill Road in Windsor. I have signed the agreements on behalf of the U.S. Department of Energy, and I am returning one signed original copy to you, By

  2. Regge trajectory of the f0(500) resonance from a dispersive connection to its pole

    SciTech Connect (OSTI)

    Nebreda, J.; Londergan, J. Timothy; Pelaez, Jose R.; Szczepaniak, Adam P.

    2014-11-01

    We report here our results on how to obtain the Regge trajectory of a resonance from its pole in a scattering process by imposing analytic constraints in the complex angular momentum plane. The method, suited for resonances that dominate an elastic scattering amplitude, has been applied to the ρ (770) and the f0(500) resonances. Whereas for the former we obtain a linear Regge trajectory, characteristic of ordinary quark-antiquark states, for the latter we find a non-linear trajectory with a much smaller slope at the resonance mass. This provides a strong indication of the non-ordinary nature of the sigma meson.

  3. Process control system of a 500-MW unit of the Reftinskaya local hydroelectric power plant

    SciTech Connect (OSTI)

    L.L. Grekhov; V.A. Bilenko; N.N. Derkach; A.I. Galperina; A.P. Strukov

    2002-05-01

    The results of the installation of a process control system developed by the Interavtomatika Company (Moscow) for controlling a 500-MW pulverized coal power unit with the use of the Teleperm ME and OM650 equipment of the Siemens Company are described. The system provides a principally new level of automation and process control through monitors comparable with the operation of foreign counterparts with complete preservation of the domestic peripheral equipment. During the 4.5 years of operation of the process control system the intricate algorithms for control and data processing have proved their operational integrity.

  4. Process Control System of a 500-MW Unit of the Reftinskaya Local Hydroelectric Power Plant

    SciTech Connect (OSTI)

    Grekhov, L. L.; Bilenko, V. A.; Derkach, N. N.; Galperina, A. I.; Strukov, A. P.

    2002-05-15

    The results of the installation of a process control system developed by the Interavtomatika Company (Moscow) for controlling a 500-MW pulverized coal power unit with the use of the Teleperm ME and OM650 equipment of the Siemens Company are described. The system provides a principally new level of automation and process control through monitors comparable with the operation of foreign counterparts with complete preservation of the domestic peripheral equipment. During the 4.5 years of operation of the process control system the intricate algorithms for control and data processing have proved their operational integrity.

  5. NA-ASC-500-13 Issue 26 ASC eNews Quarterly Newsletter

    National Nuclear Security Administration (NNSA)

    NA-ASC-500-13 Issue 26 ASC eNews Quarterly Newsletter December 2013 2 shutdown. But the two-year budget agreement is not an appropriation, so we must await final appropriations for both FY14 and FY15. The President also signed the National Defense Authorization Act into law, which directs NNSA to develop and carry out a plan to incorporate exascale computing in the Stockpile Stewardship Program. This is not an exascale program, but recognition that stockpile stewardship requires exascale

  6. Gary No. 13 blast furnace achieves 400 lbs/THM coal injection in 9 months

    SciTech Connect (OSTI)

    Sherman, G.J.; Schuett, K.J.; White, D.G.; O`Donnell, E.M.

    1995-12-01

    Number 13 Blast Furnace at Gary began injecting Pulverized Coal in March 1993. The injection level was increased over the next nine months until a level off 409 lbs/THM was achieved for the month of December 1993. Several major areas were critical in achieving this high level of Pulverized coal injection (PCI) including furnace conditions, lance position, tuyere blockage, operating philosophy, and outages. The paper discusses the modifications made to achieve this level of injection. This injection level decreased charged dry coke rate from 750 lbs/THM to about 625 lbs/THM, while eliminating 150 lbs/THM of oil and 20 lbs/THM of natural gas. Assuming a 1.3 replacement ratio for an oil/natural gas mixture, overall coke replacement for the coal is about 0.87 lbs coke/lbs coal. Gary Works anticipates levels of 500 lbs/THM are conceivable.

  7. RENEW300: Advancing Renewable Energy at HUD-Assisted Housing- Atlanta

    Broader source: Energy.gov [DOE]

    Hosted by the U.S. Department of Housing and Urban Development (HUD), this workshop helps providers and owners understand the tools and resources available via HUD's RENEW300 initiative.

  8. 300 Area Integrated Field-Scale Subsurface Research Challenge (IFRC) Field Site Management Plan

    SciTech Connect (OSTI)

    Freshley, Mark D.

    2008-12-31

    Pacific Northwest National Laboratory (PNNL) has established the 300 Area Integrated Field-Scale Subsurface Research Challenge (300 Area IFRC) on the Hanford Site in southeastern Washington State for the U.S. Department of Energys (DOE) Office of Biological and Environmental Research (BER) within the Office of Science. The project is funded by the Environmental Remediation Sciences Division (ERSD). The purpose of the project is to conduct research at the 300 IFRC to investigate multi-scale mass transfer processes associated with a subsurface uranium plume impacting both the vadose zone and groundwater. The management approach for the 300 Area IFRC requires that a Field Site Management Plan be developed. This is an update of the plan to reflect the installation of the well network and other changes.

  9. RENEW300: Advancing Renewable Energy at HUD-Assisted Housing- Minneapolis

    Broader source: Energy.gov [DOE]

    Hosted by the U.S. Department of Housing and Urban Development (HUD), this workshop helps providers and owners understand the tools and resources available via HUD's RENEW300 initiative.

  10. Evaporator Campaigns Create 300,000 Gallons of Double-Shell Tank Space

    Broader source: Energy.gov [DOE]

    RICHLAND, Wash. – Hanford’s 242-A Evaporator recently conducted back-to-back operating campaigns, creating approximately 300,000 gallons of double-shell tank waste storage space.

  11. The mobility of Nb in rutile-saturated NaCl- and NaF-bearing aqueous fluids from 1–6.5 GPa and 300–800 °C

    SciTech Connect (OSTI)

    Tanis, Elizabeth A.; Simon, Adam; Tschauner, Oliver; Chow, Paul; Xiao, Yuming; Burnley, Pamela; Cline II, Christopher J.; Hanchar, John M.; Pettke, Thomas; Shen, Guoyin; Zhao, Yusheng

    2015-08-26

    Rutile (TiO₂) is an important host phase for high field strength elements (HFSE) such as Nb in metamorphic and subduction zone environments. The observed depletion of Nb in arc rocks is often explained by the hypothesis that rutile sequesters HFSE in the subducted slab and overlying sediment, and is chemically inert with respect to aqueous fluids evolved during prograde metamorphism in the forearc to subarc environment. However, field observations of exhumed terranes, and experimental studies, indicate that HFSE may be soluble in complex aqueous fluids at high pressure (i.e., >0.5 GPa) and moderate to high temperature (i.e., >300 °C). In this study, we investigated experimentally the mobility of Nb in NaCl- and NaF-bearing aqueous fluids in equilibrium with Nb-bearing rutile at pressure-temperature conditions applicable to fluid evolution in arc environments. Niobium concentrations in aqueous fluid at rutile saturation were measured directly by using a hydrothermal diamond-anvil cell (HDAC) and synchrotron X-ray fluorescence (SXRF) at 2.1 to 6.5 GPa and 300500 °C, and indirectly by performing mass loss experiments in a piston-cylinder (PC) apparatus at ~1 GPa and 700–800 °C. The concentration of Nb in a 10 wt% NaCl aqueous fluid increases from 6 to 11 μg/g as temperature increases from 300 to 500 °C, over a pressure range from 2.1 to 2.8 GPa, consistent with a positive temperature dependence. The concentration of Nb in a 20 wt% NaCl aqueous fluid varies from 55 to 150 μg/g at 300 to 500 °C, over a pressure range from 1.8 to 6.4 GPa; however, there is no discernible temperature or pressure dependence. The Nb concentration in a 4 wt% NaF-bearing aqueous fluid increases from 180 to 910 μg/g as temperature increases from 300 to 500 °C over the pressure range 2.1 to 6.5 GPa. The data for the F-bearing fluid indicate that the Nb content of the fluid exhibits a dependence on temperature between 300 and 500 °C at ≥2 GPa, but there is no observed dependence on pressure. Together, the data demonstrate that the hydrothermal mobility of Nb is strongly controlled by the composition of the fluid, consistent with published data for Ti. At all experimental conditions, however, the concentration of Nb in the fluid is always lower than coexisting rutile, consistent with a role for rutile in moderating the Nb budget of arc rocks.

  12. 1,153-ton Waste Vault Removed from 300 Area - Vault held waste tanks with

    Energy Savers [EERE]

    contamination from Hanford's former laboratory facilities | Department of Energy 1,153-ton Waste Vault Removed from 300 Area - Vault held waste tanks with contamination from Hanford's former laboratory facilities 1,153-ton Waste Vault Removed from 300 Area - Vault held waste tanks with contamination from Hanford's former laboratory facilities February 14, 2014 - 12:00pm Addthis Media Contacts Cameron Hardy, DOE 509-376-5365, Cameron.Hardy@rl.doe.gov Mark McKenna, Washington Closure

  13. Archived News Item: August 26, 2009 - Secretary Chu Announces Nearly $300

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Million in Clean Cities Grants to Support Clean Fuels, Vehicles, and Infrastructure Development | Department of Energy 26, 2009 - Secretary Chu Announces Nearly $300 Million in Clean Cities Grants to Support Clean Fuels, Vehicles, and Infrastructure Development Archived News Item: August 26, 2009 - Secretary Chu Announces Nearly $300 Million in Clean Cities Grants to Support Clean Fuels, Vehicles, and Infrastructure Development August 26, 2009 This page has been recreated from a retired EERE

  14. Obama Administration Announces Additional $10,323,300 for Local Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Efficiency Improvements in Vermont | Department of Energy ,323,300 for Local Energy Efficiency Improvements in Vermont Obama Administration Announces Additional $10,323,300 for Local Energy Efficiency Improvements in Vermont March 26, 2009 - 12:00am Addthis WASHINGTON - Vice President Joe Biden and Energy Secretary Steven Chu today announced plans to invest $3.2 billion in energy efficiency and conservation projects in U.S. cities, counties, states, territories, and Native American tribes.

  15. Obama Administration Announces Additional $11,072,300 for Local Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Efficiency Improvements in Delaware | Department of Energy 1,072,300 for Local Energy Efficiency Improvements in Delaware Obama Administration Announces Additional $11,072,300 for Local Energy Efficiency Improvements in Delaware March 26, 2009 - 12:00am Addthis WASHINGTON - Vice President Joe Biden and Energy Secretary Steven Chu today announced plans to invest $3.2 billion in energy efficiency and conservation projects in U.S. cities, counties, states, territories, and Native American

  16. Obama Administration Announces Additional $14,521,300 for Local Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Efficiency Improvements in Rhode Island | Department of Energy 521,300 for Local Energy Efficiency Improvements in Rhode Island Obama Administration Announces Additional $14,521,300 for Local Energy Efficiency Improvements in Rhode Island March 26, 2009 - 12:00am Addthis WASHINGTON - Vice President Joe Biden and Energy Secretary Steven Chu today announced plans to invest $3.2 billion in energy efficiency and conservation projects in U.S. cities, counties, states, territories, and Native

  17. Lawrence Livermore's 'Site 300' looks back on 60 years of significant

    National Nuclear Security Administration (NNSA)

    scientific contributions | National Nuclear Security Administration Livermore's 'Site 300' looks back on 60 years of significant scientific contributions Monday, September 28, 2015 - 4:58pm NNSA Blog The entrance to Site 300 circa 1955. Sixty years ago, the University of California Radiation Laboratory began testing high explosives at what would become one of the nation's most sophisticated non-nuclear weapons testing sites, an 11 square-mile plot of rural grassland tucked away in the steep

  18. National Ignition Facility fires 300th laser target shot of fiscal year

    National Nuclear Security Administration (NNSA)

    2015 | National Nuclear Security Administration Home / Library / Press Releases National Ignition Facility fires 300th laser target shot of fiscal year 2015 August 18, 2015 WASHINGTON - Last week, the National Ignition Facility (NIF) fired its 300th laser target shot in fiscal year (FY) 2015, meeting the year's goal more than six weeks early. In comparison, the facility completed 191 target shots in FY 2014. Located at Lawrence Livermore National Laboratory (LLNL), the NIF is the world's

  19. PDSF Office Hours 10/17/13 from 2:00 to 4:00 pm at LBNL

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    0/17/13 from 2:00 to 4:00 pm at LBNL PDSF Office Hours 10/17/13 from 2:00 to 4:00 pm at LBNL October 7, 2013 I have biweekly office hours on Thursdays at LBNL. The next one is Thursday 10/17/13 from 2:00 - 4:00 pm in the NERSC drop in office at 050A-0143A (in the basement by the bus offices). Please feel free to stop by if you have any questions or want some hands on help with PDSF issues. Subscribe via RSS Subscribe Browse by Date February 2014 January 2014 November 2013 October 2013 September

  20. Neutron-Induced Microstructural Evolution of Fe-15Cr-16Ni Alloys at ~400 C During Neutron Irradiation in the FFTF Fast Reactor

    SciTech Connect (OSTI)

    Okita, Taira; Sato, Toshihiko; Sekimura, Naoto; Garner, Francis A.; Greenwood, Lawrence R.; Wolfer, W. G.; Isobe, Yoshihiro

    2001-06-30

    An experiment conducted at ~400 degrees C on simple model austenitic alloys (Fe-15Cr-16Ni and Fe-15Cr-16Ni-0.25Ti, both with and without 500 appm boron) irradiated in the FFTF fast reactor at seven different dpa rates clearly shows that lowering of the atomic displacement rate leads to a pronounced reduction in the transient regime of void swelling. While the steady state swelling rate (~1%/dpa) of these alloys is unaffected by changes in the dpa rate, the transient regime of swelling can vary from <1 to ~60 dpa when the dpa rate varies over more than two orders of magnitude. This range of dpa rates covers the full span of fusion, PWR and fast reactor rates. The origin of the flux sensitivity of swelling arises first in the evolution of the Frank dislocation loop population, its unfaulting, and the subsequent evolution of the dislocation network. There also appears to be some flux sensitivity to the void nucleation process. Most interestingly, the addition of titanium suppresses the void nucleation process somewhat, but does not alter the duration of the transient regime of swelling or its sensitivity to dpa rate. Side-by-side irradiation of boron-modified model alloys in this same experiment shows that higher helium generation rates homogenize the swelling somewhat, but do not significantly change its magnitude or flux sensitivity. The results of this study support the prediction that austenitic alloys irradiated at PWR-relevant displacement rates will most likely swell more than when irradiated at higher rates characteristic of fast reactors. Thus, the use of swelling data accumulated in fast reactors may possibly lead to an under-prediction of swelling in lower-flux PWRs and fusion devices.

  1. Grand Coulee - Bell 500-kV Transmission Line Project, Draft Environmental Impact Statement

    SciTech Connect (OSTI)

    N /A

    2002-08-09

    BPA is proposing to construct a 500-kilovolt (kV) transmission line that would extend approximately 84 miles between the Grand Coulee 500-kV Switchyard, near Grand Coulee Dam, and the Bell Substation, in Mead just north of Spokane. The new line would cross portions of Douglas, Grant, Lincoln, and Spokane counties. In addition to the transmission line, new equipment would be installed at the substations at each end of the new line and at other facilities. The proposed action would remove an existing 115-kV transmission line and replace it with the new 500-kV line on existing right-of-way for most of its length. Additional right-of-way would be needed in the first 3.5 miles out of the Grand Coulee Switchyard to connect to the existing 115-kV right-of-way. Since the mid-1990s, the transmission path west of Spokane, called the West of Hatwai transmission pathway, has grown increasingly constrained. To date, BPA has been able to manage operation of the path through available operating practices, and customer needed have been met while maintaining the reliability of the path. however, in early 2001, operations showed that the amount of electricity that needs to flow from east to west along this path creates severe transmission congestion. Under these conditions, the system is at risk of overloads and violation of industry safety and reliability standards. The problem is particularly acute in the spring and summer months because of the large amount of power generated by dams east of the path. Large amounts of water cannot be spilled during that time in order for BPA to fulfill its obligation to protect threatened and endangered fish. The amount of power that needs to move through this area during these months at times could exceed the carrying capacity of the existing transmission lines. In additional capacity is not added, BPA will run a significant risk that it will not be able to continue to meet its contractual obligations to deliver power and maintain reliability standards that minimize risks to public safety and to equipment. BPA is considering two construction alternatives, the Agency Proposed Action and the Alternative Action. The Alternative Action would include all the components of the Preferred Action except a double-circuit line would be constructed in the Spokane area between a point about 2 miles west of the Spokane River and Bell Substation, a distance of about 9 miles. BPA is also considering the No Action Alternative.

  2. Planning for the 400,000 tons/year AISI ironmaking demonstration plant

    SciTech Connect (OSTI)

    Aukrust, E. . AISI Direct Steelmaking Program)

    1993-01-01

    The American Iron and Steel Institute (AISI) has formulated a four-year program to design, construct, and operate a 400,000 net ton per year ironmaking demonstration plant. The plant will employ the coal-based ironmaking process developed under a 1989 cooperative agreement with DOE. AISI will manage the design and construction to be completed in the first two years and operate the plant for the second two years with a variety or ores, coals, and fluxes. Campaigns of increasing length are planned to optimize operations. After successful operation, the plant will be taken over by the host company. Results of studies to date indicate that, on a commercial scale, the AISI process will use 27% less energy and have variable operating costs $10 per ton lower and capital costs of $160 per annual ton, compared to the $250 per annual ton rebuild cost for the coke oven-blast furnace process it will replace. The process will enable the domestic steel industry to become more competitive by reducing its capital and operating cost. Furthermore, by eliminating the pollution problems associated with coke production and by completely enclosing the smelting reactions, this process represents a major step towards an environmentally friendly steel industry.

  3. How to program 122,400 heterogeneous cores and retain your sanity

    SciTech Connect (OSTI)

    Patkin, Scott

    2010-01-01

    Current technology trends favor hybrid architectures, typically with each node in a cluster containing both general-purpose and specialized 'accelerator' processors. The typical model for programming such systems is host-centric: The general-purpose processor orchestrates the computation, offloading performance-critical work to the accelerator, and data is communicated only among general-purpose processors. In this talk we propose a radically different hybrid-programming approach, which we call the 'reverse-acceleration model'. In this model the accelerators orchestrate the computation, offloading unacceleratable work to the general-purpose processors. Data is communicated among accelerators, not among general-purpose processors. We present the Cell Messaging Layer (CML), an implementation of the reverse-acceleration model for Los Alamos National Laboratory's Roadrunner supercomputer, a complex conglomerate of 122,400 processor cores of various types, multiple memory domains, and multiple network types, all with radically different performance characteristics but which together make Roadrunner the world's second-fastest supercomputer. CML demonstrates a new messaging-layer implementation technique called 'receiver-initiated message passing', which reduces communication latency by up to a third. Our thesis is that the reverse-acceleration model simplifies porting codes to heterogeneous systems and facilitates performance optimization. We present a case study of a legacy neutron-transport code that we modified to use reverse acceleration. Performance results from running this code across the full Roadrunner system indicate a substantial performance improvement over the unaccelerated version of the code.

  4. Stress corrosion cracking of Ni-Cu alloy 400 tubes in feedwater heaters

    SciTech Connect (OSTI)

    Amar, A.S.

    1994-12-31

    This paper presents the results of the inspections and metallurgical evaluations of a high pressure feedwater heater that experienced numerous tube failures after a short service life. Using EPRI NDE Center technical support, tubes were eddy current tested with special probes in the tubesheet region and with conventional probes in the remaining straight portion. Pulled tubes were metallurgically examined. Crack depths were correlated with eddy current indications. Short axial cracks were found on the inner surface of the tubes at roll transitions. Failures were attributed to intergranular stress corrosion cracking. The cold drawn-stress relieved Monel{trademark} (Alloy 400) tube had < 10 KSI hoop residual stress, however the residual stress was probably much higher in the roll transition. A large number of tubes were plugged based on the eddy current indications, however several tubes that showed no indications had leaked a few months later. This suggested that after initiation, crack growth was rapid. The heater was replaced after 4.5 years of service.

  5. Influence of grain size on the constitutive response and substructure evolution of MONEL 400

    SciTech Connect (OSTI)

    Gray, G.T. III, Chen, S.R.; Vecchio, K.S.

    1999-05-01

    The influence of grain size on the constitutive behavior (strain-rate and temperature dependence of the yield stress and strain hardening) and substructure evolution of MONEL 400 was investigated. Increasing the grain size from 9.5 to 202 {micro}m was seen to reduce the quasi-static yield strength from 290 to 115 MPa, while having a minimal effect on the work-hardening response. Increasing the strain rate from quasi-static to dynamic strain rates (3000 s{sup {minus}1}) was seen to increase the yield and overall flow-stress levels, but has no effect on the strong grain-size dependency exhibited of this alloy. The persistent influence of grain size to large strains is inconsistent with previous d{sup {minus}1/2} pileup grain-size modeling in the literature, which predicts convergence at large strains. Substructure evolution differences between the grain interiors and adjacent to grain boundaries supports differential defect storage processes which are consistent with previously published work-hardening d{sup {minus}1} modeling arguments for grain size-dependent strengthening in polycrystals. The integration of grain-size dependency into constitutive modeling using the mechanical threshold stress (MTS) model is discussed. The MTS model is shown to provide a robust constitutive description capturing yielding, large-strain work hardening, and grain-size effects simultaneously. The MTS model is, additionally, shown to satisfactorily address the experimentally observed transients due to strain-rate or temperature-path dependency.

  6. Department of Energy Awards $300,000 to Albuquerque’s Next Generation Economy Community Reuse Organization

    Broader source: Energy.gov [DOE]

    Department of Energy Awards $300,000 to Albuquerque’s Next Generation Economy Community Reuse Organization

  7. Niobium Thin Film Coating on a 500-MHz Copper Cavity by Plasma Deposition

    SciTech Connect (OSTI)

    Haipeng Wang; Genfa Wu; H. Phillips; Robert Rimmer; Anne-Marie Valente; Andy Wu

    2005-05-16

    A system using an Electron Cyclotron Resonance (ECR) plasma source for the deposition of a thin niobium film inside a copper cavity for superconducting accelerator applications has been designed and is being constructed. The system uses a 500-MHz copper cavity as both substrate and vacuum chamber. The ECR plasma will be created to produce direct niobium ion deposition. The central cylindrical grid is DC biased to control the deposition energy. This paper describes the design of several subcomponents including the vacuum chamber, RF supply, biasing grid and magnet coils. Operational parameters are compared between an operating sample deposition system and this system. Engineering work progress toward the first plasma creation will be reported here.

  8. SULFUR IX TO XIII SPECTRAL MEASURMENTS BETWEEN 170 AND 500 A

    SciTech Connect (OSTI)

    Yang, Z. H.; Zhang, B. L.; Wang, W.; Yu, D.Y.; Cai, X. H.; Du, S. B.; Zeng, X. T.; Chang, H. W.

    2009-04-15

    This paper reports laboratory measurements of the spectrum of highly ionized sulfur. The spectrum of S IX-S XIII has been observed in the wavelength range 170-500 A. A total of 54 lines have been measured. Forty-two of them have been classified as 2s {sup 2}2p{sup k} -2s2p{sup k} {sup +1} and 2s2p{sup k} -2p{sup k} {sup +1} transitions. Twelve other lines have been ascribed to 2s-2p, 4p-5s, 5p-6s, 5d-6p, and 6p-8d transitions. These spectral lines have been identified, among which 22 are new and accurately measured. The analysis of the spectra was based on a comparison with other experimental results and calculated values.

  9. New 500-kV Ion Source Test Strand for HIF

    SciTech Connect (OSTI)

    Sangster, T.C.; Ahle, L.E.; Halaxa, E.F.; Karpenko, V.P.; Oldaker, M.E.; Mitchell, J.W.; Beck, D.N.; Bieniosek, F.M.; Henestroza, E.; Kwan, J.W.

    2000-03-09

    One of the most challenging aspects of ion beam driven inertial fusion energy is the reliable and efficient generation of low emittance, high current ion beams. The primary ion source requirements include a rise time of order 1-{micro}sec, a pulse width of at least 20-{micro}sec, a flattop ripple of less than 0.1% and a repetition rate of at least 5-HZ. Naturally, at such a repetition rate, the duty cycle of the source must be greater than 10{sup 8} pulses. Although these specifications do not appear to exceed the state-of-the-art for pulsed power, considerable effort remains to develop a suitable high current ion source. Therefore, we are constructing a 500-kV test stand specifically for studying various ion source concepts including surface, plasma and metal vapor arc. This paper will describe the test stand design specifications as well as the details of the various subsystems and components.

  10. A New 500-kV Ion Source Test Stand for HIF

    SciTech Connect (OSTI)

    Sangster, T.C.; Ahle, L.E.; Halaxa, E.F.; Karpenko, V.P.; Oldaker, M. E.; Mitchell, J.W.; Beck, D.N.; Bieniosek, F.M.; Henestroza, E.; Kwan, J.W.

    2000-10-05

    One of the most challenging aspects of ion beam driven inertial fusion energy is the reliable and efficient generation of low emittance, high current ion beams. The primary ion source requirements include a rise time of order 1-msec, a pulse width of at least 20-msec, a flattop ripple of less than 0.1% and a repetition rate of at least 5-Hz. Naturally, at such a repetition rate, the duty cycle of the source must be greater than 108 pulses. Although these specifications do not appear to exceed the state-of-the-art for pulsed power, considerable effort remains to develop a suitable high current ion source. Therefore, we are constructing a 500-kV test stand specifically for studying various ion source concepts including surface, plasma and metal vapor arc. This paper will describe the test stand design specifications as well as the details of the various subsystems and components.

  11. Quantitative NO{sub 2} molecular tagging velocimetry at 500 kHz frame rate

    SciTech Connect (OSTI)

    Jiang, Naibo; Nishihara, Munetake; Lempert, Walter R.

    2010-11-29

    NO{sub 2} molecular tagging velocimetry (MTV) is demonstrated at repetition rates as high as 500 kHz in a laboratory scale Mach 5 wind tunnel. A pulse burst laser and a home built optical parametric oscillator system were used to simultaneously generate the required 355 and 226 nm wavelengths for NO{sub 2} photodissociation (tagging) and NO planar laser induced fluorescence imaging (interrogation), respectively. NO{sub 2} MTV images were obtained both in front and behind the characteristic bow shock from a 5 mm diameter cylinder. From Gaussian curve fitting, an average free stream flow velocity of 719 m/s was obtained. Absolute statistical precision in velocity of {approx}11.5 m/s was determined, corresponding to relative precision of 1.6%-5%, depending upon the region of the flow probed.

  12. Niobium thin film coating on a 500-MHz copper cavity by plasma deposition

    SciTech Connect (OSTI)

    Haipeng Wang; Genfa Wu; H. Phillips; Robert Rimmer; Anne-Marie Valente; Andy Wu

    2005-05-16

    A system using an Electron Cyclotron Resonance (ECR) plasma source for the deposition of a thin niobium film inside a copper cavity for superconducting accelerator applications has been designed and is being constructed. The system uses a 500-MHz copper cavity as both substrate and vacuum chamber. The ECR plasma will be created to produce direct niobium ion deposition. The central cylindrical grid is DC biased to control the deposition energy. This paper describes the design of several subcomponents including the vacuum chamber, RF supply, biasing grid and magnet coils. Operational parameters are compared between an operating sample deposition system and this system. Engineering work progress toward the first plasma creation will be reported here.

  13. Wavelength and Intensity Dependence of Short Pulse Laser Xenon Double Ionization between 500 and 2300 nm

    SciTech Connect (OSTI)

    Gingras, G.; Tripathi, A.; Witzel, B.

    2009-10-23

    The wavelength and intensity dependence of xenon ionization with 50 fs laser pulses has been studied using time-of-flight mass spectrometry. We compare the ion yield distribution of singly and doubly charged xenon with the Perelomov-Popov-Terent'ev (PPT) theory, Perelomov, Popov, and Terent'ev, Zh. Eksp. Teor. Fiz. 50, 1393 (1966) [Sov. Phys. JETP 23, 924 (1966)], in the regime between 500 and 2300 nm. The intensity dependence for each wavelength is measured in a range between 1x10{sup 13} and 1x10{sup 15} W/cm{sup 2}. The Xe{sup +}-ion signal is in good agreement with the PPT theory at all used wavelengths. In addition we demonstrate that ionic 5s5p{sup 6} {sup 2}S state is excited by an electron impact excitation process and contributes to the nonsequential double ionization process.

  14. Coiled tubing velocity string set at record 20,500 ft

    SciTech Connect (OSTI)

    Adams, L.S. )

    1992-04-13

    This paper reports that coiled tubing, set at record depth, significantly reduced costs and posed lower mechanical failure risk for recompleting a gas well in the Delaware basin of West Texas. Alternative completions such as replacing the existing tubing string with smaller diameter conventional API production tubing was deemed less economical and effective. The gas well, George M. Shelton No. 2, was recompleted on July 18, 1991, by Chevron U.S.A. Production Co. The gas is produced from the deep, low-pressure Ellenburger formation in the Gomez field. The hang-off depth of 20,500 ft set a world record for the deepest permanently installed coiled tubing. The 1-1/2 in. coiled tubing velocity string, run within the existing 4-1/2 and 4-in. tapered production tubing string, consists of seven segments that vary in wall thickness from 0.087 to 0.156 in.

  15. Threshold of photoelectron emission from CN{sub x} films deposited at room temperature and at 500 deg. C

    SciTech Connect (OSTI)

    Sago, Genki; Li Wanyan; Goto, Keisuke; Ichikawa, Yo; Ishida, Yoshihisa; Kohiki, Shigemi

    2004-10-15

    The threshold of photoelectron emission was measured for amorphous CN{sub x} films deposited at room temperature (RT) and at 500 deg. C. The x values of the films deposited at RT and at 500 deg. C by magnetron sputtering of a graphite target in a mixed N{sub 2}/Ar gas were 0.6 and 0.3, respectively. Ratios of the sp{sup 2}- to sp{sup 3}-hybridized components of both C and N for the film deposited at 500 deg. C were larger by {approx_equal}4 times than those for the film deposited at RT. The onsets of the electron emission by photon irradiation were 5.0 and 4.7 eV for the films deposited at RT and at 500 deg. C, respectively.

  16. P300

    Office of Environmental Management (EM)

    ... complete, four-part IWD, low-hazard work can be ... ESH Specialists, or Waste Management Coordinators, as well ... (SME) Involvement Hazard Level Activity Hazard Category ...

  17. P300

    Office of Environmental Management (EM)

    0 Satcon Technology Corporation - Proprietary & Confidential Satcon Technology Corporation Request for Information Response for: Addressing Policy and Logistical Challenges to Smart Grid Implementation for US Department of Energy November 1, 2010 Disclosure: Contents found herein are considered proprietary and the distribution of this proposal is restricted to only the corporation stated above. Other requests for copies of this document must be referred to Satcon Headquarters, 27 Drydock

  18. Treatability Test Plan for 300 Area Uranium Stabilization through Polyphosphate Injection

    SciTech Connect (OSTI)

    Vermeul, Vincent R.; Williams, Mark D.; Fritz, Brad G.; Mackley, Rob D.; Mendoza, Donaldo P.; Newcomer, Darrell R.; Rockhold, Mark L.; Williams, Bruce A.; Wellman, Dawn M.

    2007-06-01

    The U.S. Department of Energy has initiated a study into possible options for stabilizing uranium at the 300 Area using polyphosphate injection. As part of this effort, PNNL will perform bench- and field-scale treatability testing designed to evaluate the efficacy of using polyphosphate injections to reduced uranium concentrations in the groundwater to meet drinking water standards (30 ug/L) in situ. This technology works by forming phosphate minerals (autunite and apatite) in the aquifer that directly sequester the existing aqueous uranium in autunite minerals and precipitates apatite minerals for sorption and long term treatment of uranium migrating into the treatment zone, thus reducing current and future aqueous uranium concentrations. Polyphosphate injection was selected for testing based on technology screening as part of the 300-FF-5 Phase III Feasibility Study for treatment of uranium in the 300-Area.

  19. The Current and Historical Distribution of Special Status Amphibians at the Livermore Site and Site 300

    SciTech Connect (OSTI)

    Hattem, M V; Paterson, L; Woollett, J

    2008-08-20

    65 surveys were completed in 2002 to assess the current distribution of special status amphibians at the Lawrence Livermore National Laboratory's (LLNL) Livermore Site and Site 300. Combined with historical information from previous years, the information presented herein illustrates the dynamic and probable risk that amphibian populations face at both sites. The Livermore Site is developed and in stark contrast to the mostly undeveloped Site 300. Yet both sites have significant issues threatening the long-term sustainability of their respective amphibian populations. Livermore Site amphibians are presented with a suite of challenges inherent of urban interfaces, most predictably the bullfrog (Rana catesbeiana), while Site 300's erosion issues and periodic feral pig (Sus scrofa) infestations reduce and threaten populations. The long-term sustainability of LLNL's special status amphibians will require active management and resource commitment to maintain and restore amphibian habitat at both sites.

  20. 300 Area dangerous waste tank management system: Compliance plan approach. Final report

    SciTech Connect (OSTI)

    1996-03-01

    In its Dec. 5, 1989 letter to DOE-Richland (DOE-RL) Operations, the Washington State Dept. of Ecology requested that DOE-RL prepare ``a plant evaluating alternatives for storage and/or treatment of hazardous waste in the 300 Area...``. This document, prepared in response to that letter, presents the proposed approach to compliance of the 300 Area with the federal Resource Conservation and Recovery Act and Washington State`s Chapter 173-303 WAC, Dangerous Waste Regulations. It also contains 10 appendices which were developed as bases for preparing the compliance plan approach. It refers to the Radioactive Liquid Waste System facilities and to the radioactive mixed waste.

  1. Rocky Flats 10 year plan: over 500 structures to be demolished

    SciTech Connect (OSTI)

    Evans, B.; Bengel, P.

    1997-03-01

    Rocky Flats Environmental Technology Site has prepared a Ten Year Plan (Plan) that demonstrates how the Site would achieve accelerated cleanup and rapidly reduce the risks the Site currently poses to its workers, the public, and the environment. A major element of the Plan is the decontamination and demolition of over 500 Site facilities, including all of the former nuclear production facilities, by the end of 2006. Facilities used for the storage of plutonium, treatment of low-level mixed waste, and several office building would remain until the plutonium is removed or there is no longer a need for the facility, in which case it would be demolished. While the Plan considers all aspects of the cleanup and closure, this paper focuses on the challenges posed by the removal of highly contaminated equipment and the demolition of structures. This paper describes near- term decommissioning projects as well as the long range plans and budgets. Cash flow ultimately controls schedule, and sharing of budget priorities among processing of special nuclear material, disposing of waste, and cleaning up the environment has to be juggled carefully to attain the goals of the Plan. The total cost of the Plan exceeds $5 billion, and over $1 billion will be spent on decommissioning activities. Following removal of the plutonium and the demolition of the plutonium storage and remaining Site facilities by the end of 2015, the cost to perform the long-term environmental monitoring at the Site is estimated to be $10 million per year.

  2. Imaging magnetic domain structure in sub-500 nm thin film elements

    SciTech Connect (OSTI)

    Kirk, K. J.; McVitie, S.; Chapman, J. N.; Wilkinson, C. D. W.

    2001-06-01

    Magnetic imaging in the transmission electron microscope (TEM) has been used to examine submicron elements with the aim of discovering down to what element size complex domain patterns can form. The elements were squares, circles, triangles, and pentagons in the size range 100{endash}500 nm and were made from 36 nm Co films or 8 nm Ni{sub 80}Fe{sub 20} (NiFe) with in-plane magnetization. The magnetic domain structures in these elements were imaged at high resolution using the differential phase contrast imaging mode in a TEM. Nonuniform magnetization structures were seen in the images. Vortices were present at remanence in all shapes of 36-nm-thick Co elements down to 100 nm size and in circular NiFe elements down to 116 nm diameter. Triangular NiFe elements did not have a vortex state at remanence, instead the magnetization curved round within the element but did not achieve complete flux closure. In simulations of square and circular NiFe elements, it was found that defects at the edges of the elements encouraged reversal by a vortex mechanism, whereas for simulated elements with no defects, reversal was by rotation and occurred at much lower fields. {copyright} 2001 American Institute of Physics.

  3. Optical Spectroscopy Experiments on the 500 kA XP Pulsed-Power Generator

    SciTech Connect (OSTI)

    Bell, K. S.; Shelkovenko, T. A.; Pikuz, S. A.; McBride, R. D.; Blesener, I. C.; Knapp, P. F.; Hammer, D. A.; Greenly, J. B.; Maron, Y.

    2009-01-21

    Recent experiments on the 500 kA XP pulsed-power generator at Cornell University have explored the properties of optical spectra in single wires and wire arrays. In the single wire experiments, {approx}1% of the current from XP has been directed through the single wire. Spectra have been recorded using a half-meter spectrometer and a CCD camera located adjacent to the XP pulser. We are studying the visible spectra emitted by the wires and the background light from the machine hardware in order to identify the levels of current per wire for which visible spectroscopy might provide a means to measure magnetic field strength. We have also investigated the dependence of single wire visible spectra on the current, which was measured using a calibrated non-integrating Rogowski coil. UV and XUV diodes were employed to gather information about the temporal structure of the background and wire radiation. The line radiation in the spectra was recorded with wire currents at the few kA level. This is comparable to the first 10 ns of a 32-wire array experiment on 1 Ma generator and a 600-wire array at 20 MA.

  4. THE DISCOVERY OF BINARY WHITE DWARFS THAT WILL MERGE WITHIN 500 Myr

    SciTech Connect (OSTI)

    Kilic, Mukremin; Brown, Warren R.; Kenyon, S. J.; Allende Prieto, Carlos; Panei, J. A.

    2010-06-10

    We present radial velocity observations of four extremely low-mass (0.2 M {sub sun}) white dwarfs (WDs). All four stars show peak-to-peak radial velocity variations of 540-710 km s{sup -1} with 1.0-5.9 hr periods. The optical photometry rules out main-sequence companions. In addition, no millisecond pulsar companions are detected in radio observations. Thus, the invisible companions are most likely WDs. Two of the systems are the shortest period binary WDs yet discovered. Due to the loss of angular momentum through gravitational radiation, three of the systems will merge within 500 Myr. The remaining system will merge within a Hubble time. The mass functions for three of the systems imply companions more massive than 0.46 M {sub sun}; thus, those are carbon/oxygen core WDs. The unknown inclination angles prohibit a definitive conclusion about the future of these systems. However, the chance of a supernova Ia event is only 1%-5%. These systems are likely to form single R Coronae Borealis stars, providing evidence for a WD + WD merger mechanism for these unusual objects. One of the systems, SDSS J105353.89+520031.0, has a 70% chance of having a low-mass WD companion. This system will probably form a single helium-enriched subdwarf O star. All four WD systems have unusual mass ratios of {<=}0.2-0.8 that may also lead to the formation of AM CVn systems.

  5. Design and Fabrication of a Radiation-Hard 500-MHz Digitizer Using Deep Submicron Technology

    SciTech Connect (OSTI)

    K.K. Gan; M.O. Johnson; R.D. Kass; J. Moore

    2008-09-12

    The proposed International Linear Collider (ILC) will use tens of thousands of beam position monitors (BPMs) for precise beam alignment. The signal from each BPM is digitized and processed for feedback control. We proposed the development of an 11-bit (effective) digitizer with 500 MHz bandwidth and 2 G samples/s. The digitizer was somewhat beyond the state-of-the-art. Moreover we planned to design the digitizer chip using the deep-submicron technology with custom transistors that had proven to be very radiation hard (up to at least 60 Mrad). The design mitigated the need for costly shielding and long cables while providing ready access to the electronics for testing and maintenance. In FY06 as we prepared to submit a chip with test circuits and a partial ADC circuit we found that IBM had changed the availability of our chosen IC fabrication process (IBM 6HP SiGe BiCMOS), making it unaffordable for us, at roughly 3 times the previous price. This prompted us to change our design to the IBM 5HPE process with 0.35 µm feature size. We requested funding for FY07 to continue the design work and submit the first prototype chip. Unfortunately, the funding was not continued and we will summarize below the work accomplished so far.

  6. Demonstration of a 30-kW Microturbine with Heat Recovery in a 500-Soldier Barracks

    SciTech Connect (OSTI)

    Friedrich, Michele; Armstrong, Peter R.; Smith, David L.; Rowley, Steven

    2005-12-31

    A combined heat and power-configured microturbine system was evaluated as an alternative to grid-supplied electric power. While off-grid, the system provides auxiliary power for gas-fired boilers and a portion of the domestic hot water for a 500-man barracks and kitchen. One-time tests were made of sound levels, stack emissions and power quality. Steady-state generating capacity dropped faster than the ratings as the inlet air temperature approached 15°C, while generating efficiency, based on fuel higher heating value, did not drop as rapidly and was still almost 21% at 33°C. The microturbine must boost the fuel (natural gas) delivery pressure to 55 psig. During the one year of operation, four fuel compressors failed and there were repeated failures of the microturbine and heat recovery heat exchanger controls. Energy savings based on the measured performance and CY2003 utility rates were $2670 per year. This paper, which will be presented at the ASHRAE Annual Meeting in Orlando, Florida, Feb. 5-9, describes the results of this evaluation.

  7. Assembly of 500,000 inter-specific catfish expressed sequence tags and large scale gene-associated marker development for whole genome association studies

    SciTech Connect (OSTI)

    Catfish Genome Consortium; Wang, Shaolin; Peatman, Eric; Abernathy, Jason; Waldbieser, Geoff; Lindquist, Erika; Richardson, Paul; Lucas, Susan; Wang, Mei; Li, Ping; Thimmapuram, Jyothi; Liu, Lei; Vullaganti, Deepika; Kucuktas, Huseyin; Murdock, Christopher; Small, Brian C; Wilson, Melanie; Liu, Hong; Jiang, Yanliang; Lee, Yoona; Chen, Fei; Lu, Jianguo; Wang, Wenqi; Xu, Peng; Somridhivej, Benjaporn; Baoprasertkul, Puttharat; Quilang, Jonas; Sha, Zhenxia; Bao, Baolong; Wang, Yaping; Wang, Qun; Takano, Tomokazu; Nandi, Samiran; Liu, Shikai; Wong, Lilian; Kaltenboeck, Ludmilla; Quiniou, Sylvie; Bengten, Eva; Miller, Norman; Trant, John; Rokhsar, Daniel; Liu, Zhanjiang

    2010-03-23

    Background-Through the Community Sequencing Program, a catfish EST sequencing project was carried out through a collaboration between the catfish research community and the Department of Energy's Joint Genome Institute. Prior to this project, only a limited EST resource from catfish was available for the purpose of SNP identification. Results-A total of 438,321 quality ESTs were generated from 8 channel catfish (Ictalurus punctatus) and 4 blue catfish (Ictalurus furcatus) libraries, bringing the number of catfish ESTs to nearly 500,000. Assembly of all catfish ESTs resulted in 45,306 contigs and 66,272 singletons. Over 35percent of the unique sequences had significant similarities to known genes, allowing the identification of 14,776 unique genes in catfish. Over 300,000 putative SNPs have been identified, of which approximately 48,000 are high-quality SNPs identified from contigs with at least four sequences and the minor allele presence of at least two sequences in the contig. The EST resource should be valuable for identification of microsatellites, genome annotation, large-scale expression analysis, and comparative genome analysis. Conclusions-This project generated a large EST resource for catfish that captured the majority of the catfish transcriptome. The parallel analysis of ESTs from two closely related Ictalurid catfishes should also provide powerful means for the evaluation of ancient and recent gene duplications, and for the development of high-density microarrays in catfish. The inter- and intra-specific SNPs identified from all catfish EST dataset assembly will greatly benefit the catfish introgression breeding program and whole genome association studies.

  8. The structure and stability of aqueous rare-earth elements in hydrothermal fluids: New results on neodymium(III) aqua and chloroaqua complexes in aqueous solutions to 500 °C and 520 MPa

    SciTech Connect (OSTI)

    Mayanovic, R.A.; Anderson, A.J.; Bassett, W.A.; Chou, I.-M.

    2009-02-04

    X-ray absorption spectroscopy (XAS) measurements were made at the Nd L{sub 3}-edge on neodymium(III) aqua and chloroaqua complexes in low pH aqueous solutions from 25 to 500 C and up to 520 MPa. Analysis of the extended X-ray absorption fine structure of the XAS spectra measured from a 0.07 m Nd/0.16 m HNO{sub 3} aqueous solution reveals a contraction of the Nd-O distance of the Nd{sup 3+} aqua ion at a uniform rate of {approx} 0.013 {angstrom}/100 C and a uniform reduction of the number of coordinated H{sub 2}O molecules from 10.0 {+-} 0.9 to 7.4 {+-} 0.9 over the range from 25 to 500 C and up to 370 MPa. The rate of reduction of the first-shell water molecules with temperature for Nd{sup 3+} (26%) is intermediate between the rate for the Gd{sup 3+} aqua ion (22% from 25 to 500 C) and the rates for the Eu{sup 3+} (29% from 25 to 400 C) and the Yb{sup 3+} aqua ions (42% from 25 to 500 C) indicating an intermediate stability of the Nd{sup 3+} aqua ion consistent with the tetrad effect. Nd L{sub 3}-edge XAS measurements of 0.05 m NdCl{sub 3} aqueous solution at 25 to 500 C and up to 520 MPa show that stepwise inner-sphere complexes most likely of the type Nd(H{sub 2}O){sub {delta}-n}Cl{sub n}{sup +3-n} occur in the solution at elevated temperatures, where {delta} {approx} 9 at 150 C decreasing to {approx} 6 at 500 C and the number of chloride ions (n) of the chloroaqua complexes increases uniformly with temperature from 1.2 {+-} 0.2 to 2.0 {+-} 0.2 in the solution upon increase of temperature from 150 to 500 C. Conversely, the number of H{sub 2}O ligands of Nd(H{sub 2}O){sub {delta}-n}Cl{sub n}{sup +3-n} complexes is uniformly reduced with temperature from 7.5 {+-} 0.8 to 3.7 {+-} 0.3 in the aqueous solution, in the same temperature range. These data show greater stability of neodymium(III) than gadolinium(III) and ytterbium(III) chloride complexes in low pH aqueous solutions at elevated temperatures. Our data suggest a greater stability of aqueous light REE than that of heavy REE chloride complexes in low pH fluids at elevated temperatures consistent with REE analysis of fluids from deep-sea hydrothermal vents.

  9. Remedial investigation and feasibility study for the Lawrence Livermore National Laboratory Site 300 Pit 7 Complex

    SciTech Connect (OSTI)

    Taffet, M.J. ); Oberdorfer, J.A. ); McIlvride, W.A. )

    1989-10-01

    This report summarizes the results and conclusions of the investigation of tritium and other compounds in ground water in the vicinity of landfills at the Lawrence Livermore National Laboratory (LLNL) Site 300 Pit 7 Complex. 91 refs., 110 figs., 43 tabs.

  10. The 300 Area Integrated Field Research Challenge Quality Assurance Project Plan

    SciTech Connect (OSTI)

    Fix, N. J.

    2009-04-29

    Pacific Northwest National Laboratory and a group of expert collaborators are using the U.S. Department of Energy Hanford Site 300 Area uranium plume within the footprint of the 300-FF-5 groundwater operable unit as a site for an Integrated Field-Scale Subsurface Research Challenge (IFRC). The IFRC is entitled Multi-Scale Mass Transfer Processes Controlling Natural Attenuation and Engineered Remediation: An IFRC Focused on the Hanford Site 300 Area Uranium Plume Project. The theme is investigation of multi-scale mass transfer processes. A series of forefront science questions on mass transfer are posed for research that relate to the effect of spatial heterogeneities; the importance of scale; coupled interactions between biogeochemical, hydrologic, and mass transfer processes; and measurements/approaches needed to characterize and model a mass transfer-dominated system. This Quality Assurance Project Plan provides the quality assurance requirements and processes that will be followed by the 300 Area IFRC Project. This plan is designed to be used exclusively by project staff.

  11. 300 Area D4 Project 2nd Quarter FY06 Building Completion Report

    SciTech Connect (OSTI)

    David S. Smith

    2006-06-26

    This report documents the deactivation, decontamination, decommissioning, and demolition of 16 buildings in the 300 Area of the Hanford Site. The D4 of these facilities included characterization, engineering, removal of hazardous and radiologically contaminated materials, equipment removal, utility disconnection, deactivation, decontamination, demolition of the structure, and stabilization or removal of the remaining slab and foundation as appropriate.

  12. 300°C Capable Electronics Platform and Temperature Sensor System For Enhanced Geothermal Systems

    Broader source: Energy.gov [DOE]

    Project objectives: Enable geothermal wellbore monitoring through the development of SiC based electronics and ceramic packaging capable of sustained operation at temperatures up to 300˚C and 10 km depth. Demonstrate the technology with a temperature sensor system.

  13. PVMRW2013 Wed., Feb. 27, 3:00 Final Discussion | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    The final discussion reviewed many of the complex topics covered during the two days... PDF icon discussionnotes_weds_300.pdf More Documents & Publications PVMRW2013 Wed., Feb. 27, 1:45 Discussion notes PVMRW2013 Wed., Feb. 27, 10:00 Discussion notes:

  14. 300 Area D4 Project 3rd Quarter Fiscal Year 2006 Building Completion Report

    SciTech Connect (OSTI)

    D. S. Smith

    2006-09-25

    This report documents the deactivation, decontamination, decommissioning, and demolition of five buildings in the 300 Area of the Hanford Site. The D4 of these facilities included characterization, engineering, removal of hazardous and radiologically contaminated materials, equipment removal, utility disconnection, deactivation, decontamination, demolition of the structure, and stabilization or removal of the remaining slab and foundation as appropriate.

  15. 300 Area D4 Project Fiscal Year 2007 Building Completion Report

    SciTech Connect (OSTI)

    R. A. Westberg

    2009-01-15

    This report documents the deactivation, decontamination, decommissioning, and demolition (D4) of twenty buildings in the 300 Area of the Hanford Site. The D4 of these facilties included characterization, engineering, removal of hazardous and radiologically contaminated materials, equipment removal, utility disconnection, deactivation, decontamination, demolition of the structure, and stabilization or removal of the remaining slab and foundation, as appropriate.

  16. 100 Area and 300 Area Component of the RCBRA Fall 2005 Data Compilation

    SciTech Connect (OSTI)

    J.M. Queen

    2006-05-30

    The purpose of this report is to provide a brief description of the sampling approaches, a description of the samples collected, and the results for the Fall 2005 sampling event. This report presents the methods and results of the work to support the 100 Area and 300 Area Component of the River Corridor Baseline Risk Assessment.

  17. Dynamic tensile characterization of Vascomax® maraging C250 and C300 alloys

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Song, Bo; Wakeland, Peter Eric; Furnish, Michael D.

    2015-04-14

    Vascomax® maraging C250 and C300 alloys were dynamically characterized in tension with Kolsky tension bar techniques. Compared with conventional Kolsky tension bar experiments, a pair of lock nuts was used to minimize the pseudo stress peak and a laser system was applied to directly measure the specimen displacement. Dynamic engineering stress–strain curves of the C250 and C300 alloys were obtained in tension at 1000 and 3000 s–1. The dynamic yield strengths for both alloys were similar, but significantly higher than those obtained from quasi-static indentation tests. Both alloys exhibited insignificant strain-rate effect on dynamic yield strength. The C300 alloy showedmore » approximately 10 % higher in yield strength than the C250 alloy at the same strain rates. Necking was observed in both alloys right after yield. The Bridgman correction was applied to calculate the true stress and strain at failure for both alloys. The true failure stress showed a modest strain rate effect for both alloys but no significant difference between the two alloys at the same strain rate. As a result, the C250 alloy was more ductile than the C300 alloy under dynamic loading.« less

  18. B&W Y-12 donates $2,500 to MMC Hospitality House | Y-12 National Security

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Complex MMC Hospitality House Posted: January 27, 2014 - 1:35pm B&W Y-12 donated $2,500 to Oak Ridge Methodist Medical Center's Hospitality House. B&W Y-12 Director of Public Affairs Bill Reis, right, hands a $2,500 donation to Mike Belbeck, Methodist Medical Center's President and Chief Administrative Officer. The funds will go toward MMC's Hospitality Houses, which provide temporary lodging for patients and families who travel to Oak Ridge for extended medical treatment

  19. Lawrence Livermore National Laboratory (LLNL) Experimental Test Site (Site 300) Salinity Evaluation and Minimization Plan for Cooling Towers and Mechanical Equipment Discharges

    SciTech Connect (OSTI)

    Daily III, W D

    2010-02-24

    This document was created to comply with the Central Valley Regional Water Quality Control Board (CVRWQCB) Waste Discharge Requirement (Order No. 98-148). This order established new requirements to assess the effect of and effort required to reduce salts in process water discharged to the subsurface. This includes the review of technical, operational, and management options available to reduce total dissolved solids (TDS) concentrations in cooling tower and mechanical equipment water discharges at Lawrence Livermore National Laboratory's (LLNL's) Experimental Test Site (Site 300) facility. It was observed that for the six cooling towers currently in operation, the total volume of groundwater used as make up water is about 27 gallons per minute and the discharge to the subsurface via percolation pits is 13 gallons per minute. The extracted groundwater has a TDS concentration of 700 mg/L. The cooling tower discharge concentrations range from 700 to 1,400 mg/L. There is also a small volume of mechanical equipment effluent being discharged to percolation pits, with a TDS range from 400 to 3,300 mg/L. The cooling towers and mechanical equipment are maintained and operated in a satisfactory manner. No major leaks were identified. Currently, there are no re-use options being employed. Several approaches known to reduce the blow down flow rate and/or TDS concentration being discharged to the percolation pits and septic systems were reviewed for technical feasibility and cost efficiency. These options range from efforts as simple as eliminating leaks to implementing advanced and innovative treatment methods. The various options considered, and their anticipated effect on water consumption, discharge volumes, and reduced concentrations are listed and compared in this report. Based on the assessment, it was recommended that there is enough variability in equipment usage, chemistry, flow rate, and discharge configurations that each discharge location at Site 300 should be considered separately when deciding on an approach for reducing the salt discharge to the subsurface. The smaller units may justify moderate changes to equipment, and may benefit from increased cleaning frequencies, more accurate and suitable chemical treatment, and sources of make up water and discharge re-use. The larger cooling towers would be more suitable for automated systems where they don't already exist, re-circulation and treatment of blow down water, and enhanced chemical dosing strategies. It may be more technically feasible and cost efficient for the smaller cooling towers to be replaced by closed loop dry coolers or hybrid towers. There are several potential steps that could be taken at each location to reduce the TDS concentration and/or water use. These include: sump water filtration, minimization of drift, accurate chemical dosing, and use of scale and corrosion coupons for chemical calibration. The implementation of some of these options could be achieved by a step-wise approach taken at two representative facilities. Once viable prototype systems have been proven in the field, systematic implementation should proceed for the remaining systems, with cost, desired reduction, and general feasibility taken into consideration for such systems.

  20. Statement of Work for Drilling Four CERCLA Groundwater Monitoring Wells During Fiscal Year 2006, 300-FF-5 Operable Unit

    SciTech Connect (OSTI)

    Williams, Bruce A.

    2005-10-10

    This document contains the statement of work required to drill, characterize, and construct the proposed groundwater monitoring wells at 300-FF-5 Operable Unit during FY 2006.

  1. A 200-A, 500-Hz, triangle current-wave modulator and magnet used for particle beam rastering

    SciTech Connect (OSTI)

    Rose, C.R.; Shafer, R.E.

    1997-10-01

    This paper describes a simple 2D beam-rastering system to uniformly spread a 100-mA 6.7-MeV cw proton beam over a 50-cm by 50-cm beam stop. The basic circuit uses a 20-mF capacitor bank, a IGBT (insulated gate bipolar transistor) full-wave inverter, and a 1-mH ferrite dipole magnet to produce a {+-} 500-Gauss peak triangular-waveform deflection field at 500 Hz. A dc input voltage of 200 volts at 2.6 amps (520 watts) produces a 160-ampere peak-to-peak triangular current waveform in the ferrite magnet at 500 Hz. For dual-axis rastering, two ferrite dipoles are used, one at 500 Hz, and the other at 575 Hz, to produce a uniform 2D beam distribution at the beam stop. The paper will discuss the IGBT modulator and ferrite deflector in detail, including current and voltage waveforms, and the ferrite magnet B-dot (dB/dt) signal.

  2. The Case for a 500 GeV e{sup +}e{sub {minus}} Linear Collider

    SciTech Connect (OSTI)

    Peskin, Michael E

    2000-07-12

    Several proposals are being developed around the world for an e{sup +}e{sub {minus}} linear collider with an initial center of mass energy of 500 GeV. In this paper, the authors discuss why a project of this type deserves priority as the next major initiative in high energy physics.

  3. Toward petascale computing in geosciences: application to the Hanford 300 Area

    SciTech Connect (OSTI)

    Hammond, Glenn E.; Lichtner, Peter C.; Mills, Richard T.; Lu, Chuan

    2008-09-01

    Modeling uranium transport at the Hanford 300 Area presents new challenges for high performance computing. A field-scale three-dimensional domain with an hourly fluctuating Columbia river stage coupled to flow in highly permeable sediments results in fast groundwater flow rates requiring small time steps. In this work, high-performance computing has been applied to simulate variably saturated groundwater flow and tracer transport at the 300 Area using PFLOTRAN. Simulation results are presented for discretizations up to 10.8 million degrees of freedom, while PFLOTRAN performance was assessed on up to one billion degrees of freedom and 12,000 processor cores on Jaguar, the Cray XT4 supercomputer at ORNL.

  4. Toward petascale computing in geosciences: application to the Hanford 300 area

    SciTech Connect (OSTI)

    Hammond, Glenn; Lichtner, Peter; Mills, Richard T; Lu, Chuan

    2008-01-01

    Modeling uranium transport at the Hanford 300 Area presents new challenges for high performance computing. A field-scale three-dimensional domain with an hourly fluctuating Columbia river stage coupled to flow in highly permeable sediments results in fast groundwater flow rates requiring small time steps. In this work, high-performance computing has been applied to simulate variably saturated groundwater flow and tracer transport at the 300 Area using PFLOTRAN. Simulation results are presented for discretizations up to 10.8 million degrees of freedom, while PFLOTRAN performance was assessed on up to one billion degrees of freedom and 12,000 processor cores on Jaguar, the Cray XT4 supercomputer at ORNL.

  5. Hazard analysis for 300 Area N Reactor Fuel Fabrication and Storage Facilty

    SciTech Connect (OSTI)

    Johnson, D.J.; Brehm, J.R.

    1994-01-25

    This hazard analysis (HA) has been prepared for the 300 Area N Reactor Fuel Fabrication and Storage Facility (Facility), in compliance with the requirements of Westinghouse Hanford Company (Westinghouse Hanford) controlled manual WHC-CM-4-46, Nonreactor Facility Safety Analysis Manual, and to the direction of WHC-IP-0690, Safety Analysis and Regulation Desk Instructions, (WHC 1992). An HA identifies potentially hazardous conditions in a facility and the associated potential accident scenarios. Unlike the Facility hazard classification documented in WHC-SD-NR-HC-004, Hazard Classification for 300 Area N Reactor Fuel Fabrication and Storage Facility, (Huang 1993), which is based on unmitigated consequences, credit is taken in an HA for administrative controls or engineered safety features planned or in place. The HA is the foundation for the accident analysis. The significant event scenarios identified by this HA will be further evaluated in a subsequent accident analysis.

  6. Borehole Completion and Conceptual Hydrogeologic Model for the IFRC Well Field, 300 Area, Hanford Site

    SciTech Connect (OSTI)

    Bjornstad, Bruce N.; Horner, Jacob A.; Vermeul, Vincent R.; Lanigan, David C.; Thorne, Paul D.

    2009-04-20

    A tight cluster of 35 new wells was installed over a former waste site, the South Process Pond (316-1 waste site), in the Hanford Site 300 Area in summer 2008. This report documents the details of the drilling, sampling, and well construction for the new array and presents a summary of the site hydrogeology based on the results of drilling and preliminary geophysical logging.

  7. Secretary Chu Announces Nearly $300 Million in Clean Cities Grants to

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Support Clean Fuels, Vehicles, and Infrastructure Development | Department of Energy in Clean Cities Grants to Support Clean Fuels, Vehicles, and Infrastructure Development Secretary Chu Announces Nearly $300 Million in Clean Cities Grants to Support Clean Fuels, Vehicles, and Infrastructure Development August 26, 2009 - 12:00am Addthis WASHINGTON, DC - Energy Secretary Steven Chu today announced the selection of 25 cost-share projects under the Clean Cities program that will be funded with

  8. Microsoft PowerPoint - Hanford_Reach_Natl_Monument_300 sq.ppt [Compatibility Mode]

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Reach National Monument The Hanford Reach National Monument encompasses 300 square miles around the Hanford Site Part of the effort to reduce the active around the Hanford Site. Part of the effort to reduce the active footprint of the site involves cleanup of debris sites on Rattlesnake Mountain and the Fitzner-Eberhardt Arid Lands Ecology Reserve. The Hanford Reach was protected by Presidential proclamation in 2000 Hanford Reach was protected by Presidential proclamation in 2000. Past military

  9. Uranium Contamination in the Subsurface Beneath the 300 Area, Hanford Site, Washington

    SciTech Connect (OSTI)

    Peterson, Robert E.; Rockhold, Mark L.; Serne, R. Jeffrey; Thorne, Paul D.; Williams, Mark D.

    2008-02-29

    This report provides a description of uranium contamination in the subsurface at the Hanford Site's 300 Area. The principal focus is a persistence plume in groundwater, which has not attenuated as predicted by earlier remedial investigations. Included in the report are chapters on current conditions, hydrogeologic framework, groundwater flow modeling, and geochemical considerations. The report is intended to describe what is known or inferred about the uranium contamination for the purpose of making remedial action decisions.

  10. 300 Area D4 Project Fiscal Year 2008 Building Completion Report

    SciTech Connect (OSTI)

    R. A. Westberg

    2009-01-15

    This report documents the deactivation, decontamination, decommissioning, and demolition (D4) of eighteen buildings in the 300 Area of the Hanford Site that were demolished in Fiscal Year 2008. The D4 of these facilties included characterization, engineering, removal of hazardous and radiologically contaminated materials, equipment removal, utility disconnection, deactivation, decontamination, demolition of the structure, and stabilization or removal of the remaining slab and foundation, as appropriate.

  11. 300 Area D4 Project Fiscal Year 2009 Building Completion Report

    SciTech Connect (OSTI)

    B. J. Skwarek

    2010-01-27

    This report summarizes the deactivation, decontamination, decommissioning, and demolition activities of seven facilities in the 300 Area of the Hanford Site in fiscal year 2009. The D4 of these facilities included characterization; engineering; removal of hazardous and radiologically contaminated materials; equipment removal; utility disconnection; deactivation, decontamination, demolition of the structure; and stabilization or removal of slabs and foundations. This report also summarizes the nine below-grade slabs/foundations removed in FY09 of buildings demolished in previous fiscal years.

  12. Minimum separation distances for natural gas pipeline and boilers in the 300 area, Hanford Site

    SciTech Connect (OSTI)

    Daling, P.M.; Graham, T.M.

    1997-08-01

    The U.S. Department of Energy (DOE) is proposing actions to reduce energy expenditures and improve energy system reliability at the 300 Area of the Hanford Site. These actions include replacing the centralized heating system with heating units for individual buildings or groups of buildings, constructing a new natural gas distribution system to provide a fuel source for many of these units, and constructing a central control building to operate and maintain the system. The individual heating units will include steam boilers that are to be housed in individual annex buildings located at some distance away from nearby 300 Area nuclear facilities. This analysis develops the basis for siting the package boilers and natural gas distribution systems to be used to supply steam to 300 Area nuclear facilities. The effects of four potential fire and explosion scenarios involving the boiler and natural gas pipeline were quantified to determine minimum separation distances that would reduce the risks to nearby nuclear facilities. The resulting minimum separation distances are shown in Table ES.1.

  13. Flow and Transport in the Hanford 300 Area Vadose Zone-Aquifer-River System

    SciTech Connect (OSTI)

    Waichler, Scott R.; Yabusaki, Steven B.

    2005-07-13

    Contaminant migration in the 300 Area unconfined aquifer is strongly coupled to fluctuations in the Columbia River stage. To better understand the interaction between the river, aquifer, and vadose zone, a 2-D saturated-unsaturated flow and transport model was developed for a vertical cross-section aligned west-east across the Hanford Site 300 Area, nearly perpendicular to the river. The model was used to investigate water flow and tracer transport in the vadose zone-aquifer-river flow system, in support of the ongoing study of the 300 Area uranium plume. The STOMP simulator was used to model 1-year from 3/1/92 to 2/28/93, a period when hourly data were available for both groundwater and river levels. Net water flow to the river (per 1-meter width of shoreline) was 182 m3/y in the base case, but the cumulative exchange or total flow back and forth across the riverbed was 30 times greater. The low river case had approximately double the net water and Groundwater tracer flux into the river as compared to the base case.

  14. Isotopic Tracking of Hanford 300 Area Derived Uranium in the Columbia River

    SciTech Connect (OSTI)

    Christensen, John N.; Dresel, P. Evan; Conrad, Mark E.; Patton, Gregory W.; DePaolo, Donald J.

    2010-10-31

    Our objectives in this study are to quantify the discharge rate of uranium (U) to the Columbia River from the Hanford Site's 300 Area, and to follow that U down river to constrain its fate. Uranium from the Hanford Site has variable isotopic composition due to nuclear industrial processes carried out at the site. This characteristic makes it possible to use high-precision isotopic measurements of U in environmental samples to identify even trace levels of contaminant U, determine its sources, and estimate discharge rates. Our data on river water samples indicate that as much as 3.2 kg/day can enter the Columbia River from the 300 Area, which is only a small fraction of the total load of dissolved natural background U carried by the Columbia River. This very low-level of Hanford derived U can be discerned, despite dilution to < 1 percent of natural background U, 350 km downstream from the Hanford Site. These results indicate that isotopic methods can allow the amounts of U from the 300 Area of the Hanford Site entering the Columbia River to be measured accurately to ascertain whether they are an environmental concern, or are insignificant relative to natural uranium background in the Columbia River.

  15. Current Conditions Risk Assessment for the 300-FF-5 Groundwater Operable Unit

    SciTech Connect (OSTI)

    Miley, Terri B.; Bunn, Amoret L.; Napier, Bruce A.; Peterson, Robert E.; Becker, James M.

    2007-11-01

    This report updates a baseline risk assessment for the 300 Area prepared in 1994. The update includes consideration of changes in contaminants of interest and in the environment that have occurred during the period of interim remedial action, i.e., 1996 to the present, as well as the sub-regions, for which no initial risk assessments have been conducted. In 1996, a record of decision (ROD) stipulated interim remedial action for groundwater affected by releases from 300 Area sources, as follows: (a) continued monitoring of groundwater that is contaminated above health-based levels to ensure that concentrations continue to decrease, and (b) institutional controls to ensure that groundwater use is restricted to prevent unacceptable exposure to groundwater contamination. In 2000, the groundwater beneath the two outlying sub-regions was added to the operable unit. In 2001, the first 5-year review of the ROD found that the interim remedy and remedial action objectives were still appropriate, although the review called for additional characterization activities. This report includes a current conditions baseline ecological and human health risk assessment using maximum concentrations in the environmental media of the 300-FF-5 Operable Unit and downstream conditions at the City of Richland, Washington. The scope for this assessment includes only current measured environmental concentrations and current use scenarios. Future environmental concentrations and future land uses are not considered in this assessment.

  16. Site safety plan for Lawrence Livermore National Laboratory CERCLA investigations at site 300. Revision 2

    SciTech Connect (OSTI)

    Kilmer, J.

    1997-08-01

    Various Department of Energy Orders incorporate by reference, health and safety regulations promulgated by the Occupational Safety and Health Administration (OSHA). One of the OSHA regulations, 29 CFR 1910.120, Hazardous Waste Operations and Emergency Response, requires that site safety plans are written for activities such as those covered by work plans for Site 300 environmental investigations. Based upon available data, this Site Safety Plan (Plan) for environmental restoration has been prepared specifically for the Lawrence Livermore National Laboratory Site 300, located approximately 15 miles east of Livermore, California. As additional facts, monitoring data, or analytical data on hazards are provided, this Plan may need to be modified. It is the responsibility of the Environmental Restoration Program and Division (ERD) Site Safety Officer (SSO), with the assistance of Hazards Control, to evaluate data which may impact health and safety during these activities and to modify the Plan as appropriate. This Plan is not `cast-in-concrete.` The SSO shall have the authority, with the concurrence of Hazards Control, to institute any change to maintain health and safety protection for workers at Site 300.

  17. 70003-MAPPER FAB CARRIAGE ASSY

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    RSF RSF RSF 70003 2107 - 2107 - - - INITIAL ISSUE - - WEIGHT: 1563 LBS 146.00 CENT REF 3.00 4.00 150.00 CENT REF 6.00 SQ .50 WALL 2.00 .25 WALL 4.00 3.50 0 5.00 57.00 58.00...

  18. RangeTables.xlsx

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    30 35 40 45 eVcmmg) LET vs. Range in Si for 40 MeV SEE Beams 14 N 20 Ne 40 Ar 0 3 6 9 0 400 800 1200 1600 2000 2400 1 H 0 0.1 0.2 40 Ar 78 Kr 0 5 10 15 20 0 100 200 300 400 500...

  19. EA-1679: Grand Coulee's Third Powerplant 500-kV Transmission Line Replacement Project, Grant and Okanogon Counties, Washington

    Broader source: Energy.gov [DOE]

    This EA evaluates potential environmental impacts from the construction and operation of six new 500-kV overhead transmission lines to replace six existing underground lines at Grand Coulee Dam. DOE’s Bonneville Power Administration (BPA), a cooperating agency, was asked by the U. S. Department of the Interior’s Bureau of Reclamation to design and construct the proposed new transmission lines. A Finding of No Significant Impact was issued by BPA in December 2011.

  20. Highly resistive annealed low-temperature-grown InGaAs with sub-500 fs carrier lifetimes

    SciTech Connect (OSTI)

    Baker, C.; Gregory, I.S.; Tribe, W.R.; Bradley, I.V.; Evans, M.J.; Linfield, E.H.; Missous, M.

    2004-11-22

    We have optimized low-temperature-grown In{sub 0.3}Ga{sub 0.7}As for use in ultrafast photoconductive devices. Using low temperature ex situ annealing techniques, we have produced a photoconductive material that is highly resistive ({approx}10{sup 4} {omega} cm), has sub-500 fs carrier trapping lifetimes, and is matched to 1.06 {mu}m laser excitation.

  1. Heavy duty insulator assemblies for 500-kV bulk power transmission line with large diameter octagonalbundled conductor

    SciTech Connect (OSTI)

    Tsujimoto, K.; Hayase, I.; Hirai, J.; Inove, M.; Naito, K.; Yukino, T.

    1982-11-01

    This paper describes the design procedure and the results of field tests on mechanical performances of insulator assemblies newly developed to support octagonal-bundled conductors for 500-kV bulk power transmission. Taking account of conductor-motion-induced peak tensile load, fatigue, torsional torque and others, a successful design has been achieved in two prototype assemblies for such heavy mechanical duties as encountered during conductor galloping or swing. This has been proved throughout three years of the field tests.

  2. LA-2271 CHEMISTRY-GENERAL

    Office of Scientific and Technical Information (OSTI)

    ... V n VALUES OF P V R T FOR METHANE CALCULATED FROM THE BEATTIE-BRIDGEMAN EQUATION P , atmospheres 0,5 1 2 5 10 20 50 100 200 500 1000 100 200 300 400 500 600 700 800 900 000 ...

  3. Geothermal Heat Pump System for the New 500-bed 200,000 SF Student Housing Project at the University at Albanys Main Campus

    Broader source: Energy.gov [DOE]

    This project proposes to heat and cool planned 500-bed apartment-style student housing with closed loop vertical bore geothermal heat pump system installation.

  4. Irradiation creep of various ferritic alloys irradiated at {approximately}400{degrees}C in the PFR and FFTF reactors

    SciTech Connect (OSTI)

    Toloczko, M.B.; Garner, F.A.; Eiholzer, C.R.

    1997-04-01

    Three ferritic alloys were irradiated in two fast reactors to doses of 50 dpa or more at temperatures near 400{degrees}C. One martensitic alloy, HT9, was irradiated in both the FFTF and PFR reactors. PFR is the Prototype Fast Reactor in Dourneay, Scotland, and FFTF is the Fast Flux Test Facility in Richland, WA. D57 is a developmental alloy that was irradiated in PFR only, and MA957 is a Y{sub 2}O{sub 3} dispersion-hardened ferritic alloy that was irradiated only in FFTF. These alloys exhibited little or no void swelling at {approximately}400{degrees}C. Depending on the alloy starting condition, these steels develop a variety of non-creep strains early in the irradiation that are associated with phase changes. Each of these alloys creeps at a rate that is significantly lower than that of austenitic steels irradiated in the same experiments. The creep compliance for ferritic alloys in general appears to be {approximately}0.5 x 10{sup {minus}6} MPa{sup {minus}1} dpa{sup {minus}1}, independent of both composition and starting state. The addition of Y{sub 2}O{sub 3} as a dispersoid does not appear to change the creep behavior.

  5. Literature Review on the Effects of Prescription Fire on theEcology of Site 300

    SciTech Connect (OSTI)

    Preston, R

    2011-03-14

    Lawrence Livermore National Laboratory has historically conducted prescription burns across approximately 2,000 acres of Site 300 on an annual basis to safeguard test facilities and operations from the risk of wildfire encroachment. Prescription burns began in 1960, and although fire frequency varies among the designated burn areas, all have been burned at least once. A patchwork of native perennial grassland communities and associated special-status plant and animal populations occur onsite in many areas that have been receiving these treatments. Because the size and locations of prescription burns may shift in coming years, an evaluation is warranted to determine how these shifts may affect listed biota, including rare plants, and the distinct ecological conditions present on the site. This report presents the results of a literature review conducted by ICF International (ICF) to collect basic information on native perennial grasslands in California, the influence of fire on these grasslands, and management tools for restoring and maintaining them. The objective of this study was to review the scientific literature on California native grasslands and summarize the current state of knowledge pertaining to the possible effects -- both beneficial and detrimental -- of prescribed fire on the ecology of Site 300. The results of this review are intended to inform future management practices that may be carried out at Site 300 to maintain the plant and wildlife communities and to ensure that the ecological conditions benefit the special-status species that inhabit the Site. This review is also intended to identify a study approach to investigate changes over the next 10 years in the burned areas and in areas where burning will be discontinued.

  6. Use of Polyphosphate to Decrease Uranium Leaching in Hanford 300 Area Smear Zone Sediments

    SciTech Connect (OSTI)

    Szecsody, James E.; Zhong, Lirong; Oostrom, Martinus; Vermeul, Vincent R.; Fruchter, Jonathan S.; Williams, Mark D.

    2012-09-30

    The primary objective of this study is to summarize the laboratory investigations performed to evaluate short- and long-term effects of phosphate treatment on uranium leaching from 300 area smear zone sediments. Column studies were used to compare uranium leaching in phosphate-treated to untreated sediments over a year with multiple stop flow events to evaluate longevity of the uranium leaching rate and mass. A secondary objective was to compare polyphosphate injection, polyphosphate/xanthan injection, and polyphosphate infiltration technologies that deliver phosphate to sediment.

  7. Efficient methylammonium lead iodide perovskite solar cells with active layers from 300 to 900 nm

    SciTech Connect (OSTI)

    Momblona, C.; Malinkiewicz, O.; Soriano, A.; Gil-Escrig, L.; Bandiello, E.; Scheepers, M.; Bolink, H. J.; Edri, E.

    2014-08-01

    Efficient methylammonium lead iodide perovskite-based solar cells have been prepared in which the perovskite layer is sandwiched in between two organic charge transporting layers that block holes and electrons, respectively. This configuration leads to stable and reproducible devices that do not suffer from strong hysteresis effects and when optimized lead to efficiencies close to 15%. The perovskite layer is formed by using a dual-source thermal evaporation method, whereas the organic layers are processed from solution. The dual-source thermal evaporation method leads to smooth films and allows for high precision thickness variations. Devices were prepared with perovskite layer thicknesses ranging from 160 to 900 nm. The short-circuit current observed for these devices increased with increasing perovskite layer thickness. The main parameter that decreases with increasing perovskite layer thickness is the fill factor and as a result optimum device performance is obtained for perovskite layer thickness around 300 nm. However, here we demonstrate that with a slightly oxidized electron blocking layer the fill factor for the solar cells with a perovskite layer thickness of 900 nm increases to the same values as for the devices with thin perovskite layers. As a result the power conversion efficiencies for the cells with 300 and 900 nm are very similar, 12.7% and 12%, respectively.

  8. MICROSCALE METABOLIC, REDOX AND ABIOTIC REACTIONS IN HANFORD 300 AREA SUBSURFACE SEDIMENTS

    SciTech Connect (OSTI)

    Beyenal, Haluk; McLEan, Jeff; Majors, Paul; Fredrickson, Jim

    2013-11-14

    The Hanford 300 Area is a unique site due to periodic hydrologic influence of river water resulting in changes in groundwater elevation and flow direction. This area is also highly subject to uranium remobilization, the source of which is currently believed to be the region at the base of the vadose zone that is subject to period saturation due to the changes in the water levels in the Columbia River. We found that microbial processes and redox and abiotic reactions which operate at the microscale were critical to understanding factors controlling the macroscopic fate and transport of contaminants in the subsurface. The combined laboratory and field research showed how microscale conditions control uranium mobility and how biotic, abiotic and redox reactions relate to each other. Our findings extended the current knowledge to examine U(VI) reduction and immobilization using natural 300 Area communities as well as selected model organisms on redox-sensitive and redox-insensitive minerals. Using innovative techniques developed specifically to probe biogeochemical processes at the microscale, our research expanded our current understanding of the roles played by mineral surfaces, bacterial competition, and local biotic, abiotic and redox reaction rates on the reduction and immobilization of uranium.

  9. REVIEW REPORT: BUILDING C-400 THERMAL TREATMENT 90 PERCENT REMEDIAL DESIGN REPORT AND SITE INVESTIGATION, PGDP, PADUCAH, KENTUCKY

    SciTech Connect (OSTI)

    Looney, B; Jed Costanza, J; Eva Davis, E; Joe Rossabi, J; Lloyd Stewart, L; Hans Stroo, H

    2007-08-15

    On 9 April 2007, the U.S. Department of Energy (DOE) Headquarters, Office of Soil and Groundwater Remediation (EM-22) initiated an Independent Technical Review (ITR) of the 90% Remedial Design Report (RDR) and Site Investigation (RDSI) for thermal treatment of trichloroethylene (TCE) in the soil and groundwater in the vicinity of Building C-400 at the Paducah Gaseous Diffusion Plant (PGDP). The general ITR goals were to assess the technical adequacy of the 90% RDSI and provide recommendations sufficient for DOE to determine if modifications are warranted pertaining to the design, schedule, or cost of implementing the proposed design. The ultimate goal of the effort was to assist the DOE Paducah/Portsmouth Project Office (PPPO) and their contractor team in ''removing'' the TCE source zone located near the C-400 Building. This report provides the ITR findings and recommendations and supporting evaluations as needed to facilitate use of the recommendations. The ITR team supports the remedial action objective (RAO) at C-400 to reduce the TCE source area via subsurface Electrical Resistance Heating (ERH). Further, the ITR team commends PPPO, their contractor team, regulators, and stakeholders for the significant efforts taken in preparing the 90% RDR. To maximize TCE removal at the target source area, several themes emerge from the review which the ITR team believes should be considered and addressed before implementing the thermal treatment. These themes include the need for: (1) Accurate and site-specific models as the basis to verify the ERH design for full-scale implementation for this challenging hydrogeologic setting; (2) Flexible project implementation and operation to allow the project team to respond to observations and data collected during construction and operation; (3) Defensible performance metrics and monitoring, appropriate for ERH, to ensure sufficient and efficient clean-up; and (4) Comprehensive (creative and diverse) contingencies to address the potential for system underperformance, and other unforeseen conditions These themes weave through the ITR report and the various analyses and recommendations. The ITR team recognizes that a number of technologies are available for treatment of TCE sources. Further, the team supports the regulatory process through which the selected remedy is being implemented, and concurs that ERH is a potentially viable remedial technology to meet the RAOs adjacent to C-400. Nonetheless, the ITR team concluded that additional efforts are needed to provide an adequate basis for the planned ERH design, particularly in the highly permeable Regional Gravel Aquifer (RGA), where sustaining target temperatures present a challenge. The ERH design modeling in the 90% RDR does not fully substantiate that heating in the deep RGA, at the interface with the McNairy formation, will meet the design goals; specifically the target temperatures. Full-scale implementation of ERH to meet the RAOs is a challenge in the complex hydrogeologic setting at PGDP. Where possible, risks to the project identified in this ITR report as ''issues'' and ''recommendations'' should be mitigated as part of the final design process to increase the likelihood of remedial success. The ITR efforts were organized into five lines of inquiry (LOIs): (1) Site investigation and target zone delineation; (2) Performance objectives; (3) Project and design topics; (4) Health and safety; and (5) Cross cutting and independent cost evaluation. Within each of these LOIs, the ITR team identified a series of unresolved issues--topics that have remaining uncertainties or potential project risks. These issues were analyzed and one or more recommendations were developed for each. In the end, the ITR team identified 27 issues and provided 50 recommendations. The issues and recommendations are briefly summarized below, developed in Section 5, and consolidated into a single list in Section 6. The ITR team concluded that there are substantive unresolved issues and system design uncertainties, resulting in technical and financial risks to DOE.

  10. Observation of parametric X-rays produced by 400 GeV/c protons in bent crystals

    SciTech Connect (OSTI)

    Scandale , W.; Robert-Demolaize, G.; Arduini, G.; Assmann, R.; Cerutti, F. et al

    2011-05-30

    Spectral maxima of parametric X-ray radiation (PXR) produced by 400 GeV/c protons in bent silicon crystals aligned with the beam have been observed in an experiment at the H8 external beam of the CERN SPS. The total yield of PXR photons was about 10{sup -6} per proton. Agreement between calculations and the experimental data shows that the PXR kinematic theory is valid for bent crystals with sufficiently small curvature as used in the experiment. The intensity of PXR emitted from halo protons in a bent crystal used as a primary collimator in a circular accelerator may be considered as a possible tool to control its crystal structure, which is slowly damaged because of irradiation. The intensity distribution of PXR peaks depends on the crystal thickness intersected by the beam, which changes for different orientations of a crystal collimator. This dependence may be used to control crystal collimator alignment by analyzing PXR spectra produced by halo protons.

  11. Observation of Parametric X-Rays Produced by 400-GeV/C Protons in Bent Crystals

    SciTech Connect (OSTI)

    Scandale, W.; Arduini, G.; Assmann, R.; Cerutti, F.; Gilardoni, S.; Christiansen, J.; Laface, E.; Losito, R.; Masi, A.; Metral, E.; Mirarchi, D.; Montesano, S.; Previtali, V.; Redaelli, S.; Valentino, G.; Schoofs, P.; Smirnov, G.; Tlustos, L.; Bagli, E.; Baricordi, S.; Dalpiaz, P.; /Ferrara U. /INFN, Ferrara /Ferrara U. /INFN, Ferrara /Ferrara U. /INFN, Ferrara /Ferrara U. /INFN, Ferrara /Frascati /Frascati /Frascati /INFN, Legnaro /INFN, Legnaro /INFN, Legnaro /INFN, Legnaro /INFN, Legnaro /INFN, Legnaro /INFN, Rome /INFN, Rome /INFN, Rome /INFN, Rome /INFN, Naples /Serpukhov, IHEP /Serpukhov, IHEP /Serpukhov, IHEP /Serpukhov, IHEP /Serpukhov, IHEP /Dubna, JINR /Dubna, JINR /St. Petersburg, INP /St. Petersburg, INP /St. Petersburg, INP /St. Petersburg, INP /Imperial Coll., London /Imperial Coll., London /Imperial Coll., London /Imperial Coll., London /Imperial Coll., London /Imperial Coll., London /Imperial Coll., London /Imperial Coll., London /Brookhaven /SLAC /SLAC /SLAC /IPTP, Dubna /Tomsk Polytechnic U. /Tomsk Polytechnic U.

    2012-05-07

    Spectral maxima of parametric X-ray radiation (PXR) produced by 400 GeV/c protons in bent silicon crystals aligned with the beam have been observed in an experiment at the H8 external beam of the CERN SPS. The total yield of PXR photons was about 10{sup -6} per proton. Agreement between calculations and the experimental data shows that the PXR kinematic theory is valid for bent crystals with sufficiently small curvature as used in the experiment. The intensity of PXR emitted from halo protons in a bent crystal used as a primary collimator in a circular accelerator may be considered as a possible tool to control its crystal structure, which is slowly damaged because of irradiation. The intensity distribution of PXR peaks depends on the crystal thickness intersected by the beam, which changes for different orientations of a crystal collimator. This dependence may be used to control crystal collimator alignment by analyzing PXR spectra produced by halo protons.

  12. Deuterated palladium at temperatures from 4. 3 to 400 K and pressures to 105 kbar: Search for cold fusion

    SciTech Connect (OSTI)

    Silvera, I.F.; Moshary, F. )

    1990-11-15

    We have studied a sample of deuterated palladium at pressures up to 105 kbar and temperatures from 4.3 to 400 K in an effort to detect cold fusion. A (D)/(Pd) concentration of 1.34{plus minus}0.1 was achieved. No evidence of cold fusion was found with a limit of 2.5{times}10{sup {minus}18} fusions (DD pair){sup {minus}1} s{sup {minus}1} from neutron detection and 1.5{times}10{sup {minus}8} fusions (DD pair){sup {minus}1} s{sup {minus}1} from detection of possible heating; a {gamma}-ray detector showed no evidence of {gamma} rays differing from background.

  13. Irradiation Creep and Swelling from 400 C to 600 C of the Oxide Dispersion Strengthened Ferritic Alloy MA957

    SciTech Connect (OSTI)

    Toloczko, Mychailo B.; Gelles, David S.; Garner, Francis A.; Kurtz, Richard J.; Abe, Katsunori

    2004-04-24

    Recently, there has been a growing interest in the use of oxide dispersion strengthened (ODS) ferritic steels for fusion reactor applications. As part of an extensive study performed at PNNL on the ODS steel MA957 [1], irradiation creep tests were performed on pressurized tubes made from MA957 by two different methods. The tubes were made either by gun drilling alone or by a combination of rod drawing and gun drilling. The different fabrication methods were explored because ODS steels have been difficult to form. The pressurized tubes were irradiated in the Fast Flux Test Facility (FFTF) to doses ranging from 40 dpa to 110 dpa at temperatures ranging from 400 C to 600 C. The effective stresses resulting from the pressurization of the tubes ranged from 0 MPa to 175 MPa.

  14. EA-1177: Salvage/Demolition of 200 West Area, 200 East Area, and 300 Area Steam Plants, Richland, Washington

    Broader source: Energy.gov [DOE]

    This EA evaluates the environmental impacts for the proposal to salvage and demolish the 200 West Area, 200 East Area, and 300 Area steam plants and their associated steam distribution piping...

  15. Solar and Energy Loan Fund Receives $300,000 Community Reinvestment Act Loan to Invest in Home Energy Upgrades

    Broader source: Energy.gov [DOE]

    Residential Network member and Better Buildings Neighborhood Program partner Solar and Energy Loan Fund (SELF) received its first Community Reinvestment Act loan from PNC Bank in May for $300,000.

  16. Final Hazard Categorization for the Remediation of Six 300-FF-2 Operable Unit Solid Waste Burial Grounds

    SciTech Connect (OSTI)

    J. D. Ludowise; K. L. Vialetti

    2008-05-12

    This report provides the final hazard categorization for the remediation of six 300-FF-2 Operable Unit Burial Grounds, the 618-1, 618-2, 618-3, 618-7, 618-8, and 618-13 sites.

  17. Virginia Underground Natural Gas Storage Capacity

    U.S. Energy Information Administration (EIA) Indexed Site

    9,500 9,500 9,500 9,500 9,500 9,500 2002-2016 Total Working Gas Capacity 5,400 5,400 5,400 5,400 5,400 5,400 2012-2016 Total Number of Existing Fields 2 2 2 2 2 2

  18. Enhanced High Harmonic Generation from Multiply Ionized Argon above 500 eV through Laser Pulse Self-Compression

    SciTech Connect (OSTI)

    Arpin, P.; Popmintchev, T.; Kapteyn, H. C.; Murnane, M. M.; Wagner, N. L.; Cohen, O.

    2009-10-02

    By combining laser pulse self-compression and high harmonic generation within a single waveguide, we demonstrate high harmonic emission from multiply charged ions for the first time. This approach enhances the laser intensity and counteracts ionization-induced defocusing, extending the cutoff photon energy in argon above 500 eV for the first time, with higher spectral intensity and cutoff energy than He for the same input laser parameters. This Letter demonstrates a pathway for extending high harmonic emission to very high photon energies using large, multiply charged, ions with high ionization potentials.

  19. The results of systems tests of the 500 kV busbar controllable shunting reactor in the Tavricheskaya substation

    SciTech Connect (OSTI)

    Gusev, S. I.; Karpov, V. N.; Kiselev, A. N.; Kochkin, V. I.

    2009-09-15

    The results of systems tests of the 500 kV busbar magnetization-controllable shunting reactor (CSR), set up in the Tavricheskaya substation, including measurements of the quality of the electric power, the harmonic composition of the network currents of the reactor for different values of the reactive power consumed, the determination of the regulating characteristics of the reactor, the speed of response of the shunting reactor in the current and voltage stabilization modes, and also the operation of the reactor under dynamic conditions for different perturbations, are presented. The results obtained are analyzed.

  20. Performance of the beam chamber vacuum system of K = 500 cyclotron at Variable Energy Cyclotron Centre Kolkata

    SciTech Connect (OSTI)

    Pal, Gautam DuttaGupta, Anjan; Chakrabarti, Alok

    2014-07-15

    The beam chamber of Variable Energy Cyclotron Centre, Kolkata's K = 500 superconducting cyclotron is pumped by liquid helium cooled cryopanel with liquid nitrogen cooled radiation shield. Performance of the vacuum system was evaluated by cooling the cryopanel assembly with liquid nitrogen and liquid helium. Direct measurement of beam chamber pressure is quite difficult because of space restrictions and the presence of high magnetic field. Pressure gauges were placed away from the beam chamber. The beam chamber pressure was evaluated using a Monte Carlo simulation software for vacuum system and compared with measurements. The details of the vacuum system, measurements, and estimation of pressure of the beam chamber are described in this paper.

  1. Architecture and technology of 500 Msample/s feedback systems for control of coupled-bunch instabilities

    SciTech Connect (OSTI)

    Teytelman, Dmitry

    2000-03-30

    Feedback control of coupled-bunch instabilities presents many challenges. Control bandwidths up to 250 MHz are required to damp all of the unstable coupled-bunch modes in recent accelerators. A digital parallel-processing array with 80 DSPs has been developed to control longitudinal instabilities in PEP-II/ALS/DA NE machines. Here the authors present a description of the architecture as well as the technologies used to implement 500 Msample/s real-time control system with 2,000 FIR filtering channels. Algorithms for feedback control, data acquisition, and analysis are described and measurements from ALS are presented.

  2. B&W Y-12 donates $2,500 to local Girl Scouts summer camp program | Y-12

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    National Security Complex local Girl Scouts summer camp program Posted: June 27, 2013 - 3:39pm OAK RIDGE, Tenn. - Booth Kammann, (center, left in photo) CEO of the Girl Scout Council of the Southern Appalachians, accepts a donation of $2,500 from Nancy Johnson, B&W Y-12's vice president of Business Services and Performance Assurance, which will help fund the summer program at Camp Tanasi, located near Andersonville on Norris Lake. Joining Kammann and Johnson are (from left in photo)

  3. M400.pdf

    National Nuclear Security Administration (NNSA)

  4. Formation of a laminar electron flow for 300 GHz high-power pulsed gyrotron

    SciTech Connect (OSTI)

    Yamaguchi, Yuusuke; Tatematsu, Yoshinori; Saito, Teruo; Ikeda, Ryosuke; Mudiganti, Jagadish C.; Ogawa, Isamu; Idehara, Toshitaka [Research Center for Development of Far-Infrared Region, University of Fukui, 3-9-1 Bunkyo, Fukui-shi 910-8507 (Japan)

    2012-11-15

    This paper describes the design of a triode magnetron injection gun for use in a 200 kW, 300 GHz gyrotron. As power and frequency increase, the performance of the gyrotron becomes quite sensitive to the quality of the electron beam. Formation of a laminar electron flow is essential for the realization of a high quality beam with a small velocity spread. In this study, a new method is developed for a quantitative evaluation of the laminarity and is applied to optimize the electrode design. The laminarity depends not only on conventional design parameters such as the cathode slant angle but also on the spatial distribution of the electric field along the beam trajectory. In the optimized design, the velocity pitch factors, {alpha}, larger than 1.2 are obtained at 65 kV, 10 A with spreads, {Delta}{alpha}, less than 5%.

  5. Remedial investigation of the High-Explosives (HE) Process Area, Lawrence Livermore National Laboratory Site 300

    SciTech Connect (OSTI)

    Crow, N.B.; Lamarre, A.L.

    1990-08-01

    This report presents the results of a Remedial Investigation (RI) to define the extent of high explosives (HE) compounds and volatile organic compounds (VOCs) found in the soil, rocks, and ground water of the HE Process Area of Lawrence Livermore National Laboratory's (LLNL) Site 300 Facility. The report evaluates potential public health environmental risks associated with these compounds. Hydrogeologic information available before February 15, 1990, is included; however, chemical analyses and water-level data are reported through March 1990. This report is intended to assist the California Regional Water Quality Control Board (RWQCB)--Central Valley Region and the US Environmental Protection Agency (EPA) in evaluating the extent of environmental contamination of the LLNL HE Process Area and ultimately in designing remedial actions. 90 refs., 20 figs., 7 tabs.

  6. Hazardous waste site assessment: Inactive landfill, Site 300, Lawrence Livermore National Laboratory

    SciTech Connect (OSTI)

    Not Available

    1985-01-01

    This report presents the results of an investigation of an inactive landfill (Pit 6) at Lawrence Livermore National Laboratory's (LLNL) Site 300. The primary objectives were to: collect and review background information pertaining to past waste disposal practices and previous environmental characterization studies; conduct a geophysical survey of the landfill area to locate the buried wastes; conduct a hydrogeologic investigation to provide additional data on the rate and direction of groundwater flow, the extent of any groundwater contamination, and to investigate the connection, if any, of the shallow groundwater beneath the landfill with the local drinking water supply; conduct a risk assessment to identify the degree of threat posed by the landfill to the public health and environment; compile a preliminary list of feasible long-term remedial action alternatives for the landfill; and develop a list of recommendations for any interim measures necessary at the landfill should the long-term remedial action plan be needed.

  7. Title I conceptual design for Pit 6 landfill closure at Lawrence Livermore National Laboratory Site 300

    SciTech Connect (OSTI)

    MacDonnell, B.A.; Obenauf, K.S.

    1996-08-01

    The objective of this design project is to evaluate and prepare design and construction documents for a closure cover cap for the Pit 6 Landfill located at Lawrence Livermore National Laboratory Site 300. This submittal constitutes the Title I Design (Conceptual Design) for the closure cover of the Pit 6 Landfill. A Title I Design is generally 30 percent of the design effort. Title H Design takes the design to 100 percent complete. Comments and edits to this Title I Design will be addressed in the Title II design submittal. Contents of this report are as follows: project background; design issues and engineering approach; design drawings; calculation packages; construction specifications outline; and construction quality assurance plan outline.

  8. A Novel Fuel/Reactor Cycle to Implement the 300 Years Nuclear Waste Policy Approach - 12377

    SciTech Connect (OSTI)

    Carelli, M.D.; Franceschini, F.; Lahoda, E.J.; Petrovic, B.

    2012-07-01

    A thorium-based fuel cycle system can effectively burn the currently accumulated commercial used nuclear fuel and move to a sustainable equilibrium where the actinide levels in the high level waste are low enough to yield a radiotoxicity after 300 years lower than that of the equivalent uranium ore. The second step of the Westinghouse approach to solving the waste 'problem' has been completed. The thorium fuel cycle has indeed the potential of burning the legacy TRU and achieve the waste objective proposed. Initial evaluations have been started for the third step, development and selection of appropriate reactors. Indications are that the probability of show-stoppers is rather remote. It is, therefore, believed that development of the thorium cycle and associated technologies will provide a permanent solution to the waste management. Westinghouse is open to the widest collaboration to make this a reality. (authors)

  9. High Luminosity Options for the JLC.NLC at 500 GeV cms(LCC-0004)

    SciTech Connect (OSTI)

    Raubenheimer, T

    2004-04-22

    The present JLC/NLC parameters are chosen to provide luminosities between 0.5 {approx} 0.75 x 10{sup 34} s{sup -1} cm{sup -2} at a cms energy of 500 GeV; the parameters are listed in Table 1 for both the 500 GeV and 1 TeV cases. In all cases, these luminosities assume extensive margins and emittance dilutions to ensure that they are attainable. In this note, they consider the feasibility of substantially higher luminosities which might be attained by operating with smaller emittance dilutins and higher beam currents. The parameters they describe are listed in Table 2 where these high luminosity sets (ILC-IHa and ILC-IHb) are compared with the base JLC/NLC set (ILC-Ib) and with the high luminosity TESLA parameter set. In the next sections, they will discuss the limitations and assumptions leading to these higher luminosity parameter sets. The details in their discussion will be based on the NLC design described in the Zeroth-order Design Report (ZDR) but the same arguments, with slightly different values, could be applied to the JLC reference design.

  10. An experimental setup for the simultaneous measurement of thermoelectric power of two samples from 77 K to 500 K

    SciTech Connect (OSTI)

    Tripathi, T. S.; Bala, M.; Asokan, K.

    2014-08-01

    We report on an experimental setup for the simultaneous measurement of the thermoelectric power (TEP) of two samples in the temperature range from 77 K to 500 K using optimum electronic instruments. The setup consists of two rectangular copper bars in a bridge arrangement for sample mounting, two surface mount (SM) chip resistors for creating alternate temperature gradient, and a type E thermocouple in differential geometry for gradient temperature (ΔT) measurement across the samples. In addition, a diode arrangement has been made for the alternate heating of SM resistors using only one DC current source. The measurement accuracy of ΔT increases with the differential thermocouple arrangement. For the calibration of the setup, measurements of TEP on a high purity (99.99%) platinum wire and type K thermocouple wires Chromel and Alumel have been performed from 77 K to 500 K with respect to copper lead wires. Additionally, this setup can be utilized to calibrate an unknown sample against a sample of known absolute TEP.

  11. Thermoluminescence (TL) Analysis and Fading Studies of Naturally Occurring Salt Irradiated by 500 mGy Gamma Rays

    SciTech Connect (OSTI)

    Tiwari, Ramesh Chandra; Pau, Kham Suan

    2011-10-20

    The aim of the present study was to investigate the potential of the naturally occurring salt for the dosimetry purposes, using TL. The fine powder samples (20 mg) were irradiated by {gamma}- rays from 500 mGy to 2500 mGy by using Theratron-780C Cobalt-60 source, however, this paper discusses about 500 mGy only. The TL glow curve peak parameters were studied by using Chen's peak shape equation. TL glow curves were compared with fitted curves using glow curve deconvolution (GCD) method by using Kitis expression. The kinetic parameter values (E, b and s) so calculated, are in good agreement with those available in literature. The calculated energy values were also verified by using various heating rate (VHR) method. {chi}{sup 2} test and figure of merit (FOM) calculation was done to accept the goodness of fit between the curves. Fading studies of the sample showed a good fitting between the curves. The analysis suggests that natural salt should be considered for dosimetry purposes.

  12. Application of RAD-BCG calculator to Hanford's 300 area shoreline characterization dataset

    SciTech Connect (OSTI)

    Antonio, Ernest J.; Poston, Ted M.; Tiller, Brett L.; Patton, Gene W.

    2003-07-01

    Abstract. In 2001, a multi-agency study was conducted to characterize potential environmental effects from radiological and chemical contaminants on the near-shore environment of the Columbia River at the 300 Area of the U.S. Department of Energy’s Hanford Site. Historically, the 300 Area was the location of nuclear fuel fabrication and was the main location for research and development activities from the 1940s until the late 1980s. During past waste handling practices uranium, copper, and other heavy metals were routed to liquid waste streams and ponds near the Columbia River shoreline. The Washington State Department of Health and the Pacific Northwest National Laboratory’s Surface Environmental Surveillance Project sampled various environmental components including river water, riverbank spring water, sediment, fishes, crustaceans, bivalve mollusks, aquatic insects, riparian vegetation, small mammals, and terrestrial invertebrates for analyses of radiological and chemical constituents. The radiological analysis results for water and sediment were used as initial input into the RAD-BCG Calculator. The RAD-BCG Calculator, a computer program that uses an Excel® spreadsheet and Visual Basic® software, showed that maximum radionuclide concentrations measured in water and sediment were lower than the initial screening criteria for concentrations to produce dose rates at existing or proposed limits. Radionuclide concentrations measured in biota samples were used to calculate site-specific bioaccumulation coefficients (Biv) to test the utility of the RAD-BCG-Calculator’s site-specific screening phase. To further evaluate site-specific effects, the default Relative Biological Effect (RBE) for internal alpha particle emissions was reduced by half and the program’s kinetic/allometric calculation approach was initiated. The subsequent calculations showed the initial RAD-BCG Calculator results to be conservative, which is appropriate for screening purposes.

  13. Identification and In-vivo Characterization of a Novel OhrR Transcriptional Regulator in Burkholderia xenovorans LB400

    SciTech Connect (OSTI)

    Nguyen, Tinh T.; Mart-Arbona, Ricardo; Hall, Richard S.; Maity, Tuhin; Valdez, Yolanda E.; Dunbar, John M.; Unkefer, Clifford J.; Unkefer, Pat J.

    2013-05-21

    Transcriptional regulators (TRs) are an important and versatile group of proteins, yet very little progress has been achieved towards the discovery and annotation of their biological functions. We have characterized a previously unknown organic hydroperoxide resistance regulator from Burkholderia xenovoransLB400, Bxe_B2842, which is homologous to E. colis OhrR. Bxe_B2842 regulates the expression of an organic hydroperoxide resistance protein (OsmC). We utilized frontal affinity chromatography coupled with mass spectrometry (FAC-MS) and electrophoretic mobility gel shift assays (EMSA) to identify and characterize the possible effectors of the regulation by Bxe_B2842. Without an effector, Bxe_B2842 binds a DNA operator sequence (DOS) upstream of osmC. FAC-MS results suggest that 2-aminophenol binds to the protein and is potentially an effector molecule. EMSA analysis shows that 2-aminophenol also attenuates the Bxe_B2842s affinity for its DOS. EMSA analysis also shows that organic peroxides attenuate Bxe_B2842/DOS affinity, suggesting that binding of the TR to its DOS is regulated by the two-cysteine mechanism, common to TRs in this family. Bxe_B2842 is the first OhrR TR to have both oxidative and effector-binding mechanisms of regulation. Our paper reveals further mechanistic diversity TR mediated gene regulation and provides insights into methods for function discovery of TRs.

  14. High 400?C operation temperature blue spectrum concentration solar junction in GaInN/GaN

    SciTech Connect (OSTI)

    Zhao, Liang; Detchprohm, Theeradetch; Wetzel, Christian

    2014-12-15

    Transparent wide gap junctions suitable as high temperature, high flux topping cells have been achieved in GaInN/GaN by metal-organic vapor phase epitaxy. In structures of 25 quantum wells (QWs) under AM1.5G illumination, an open circuit voltage of 2.1?V is achieved. Of the photons absorbed in the limited spectral range of <450?nm, 64.2% are converted to electrons collected at the contacts under zero bias. At a fill factor of 45%, they account for a power conversion efficiency of38.6%. Under concentration, the maximum output power density per sun increases from 0.49?mW/cm{sup 2} to 0.51?mW/cm{sup 2} at 40?suns and then falls 0.42?mW/cm{sup 2} at 150?suns. Under external heating, a maximum of 0.59?mW/cm{sup 2} is reached at 250?C. Even at 400?C, the device is fully operational and exceeds room temperature performance. A defect analysis suggests that significantly higher fill factors and extension into longer wavelength ranges are possible with further development. The results prove GaInN/GaN QW solar junctions a viable and rugged topping cell for concentrator photovoltaics with minimal cooling requirements. By capturing the short range spectrum, they reduce the thermal load to any conventional cells stacked behind.

  15. Identification and In-vivo Characterization of a Novel OhrR Transcriptional Regulator in Burkholderia xenovorans LB400

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Nguyen, Tinh T.; Martí-Arbona, Ricardo; Hall, Richard S.; Maity, Tuhin; Valdez, Yolanda E.; Dunbar, John M.; Unkefer, Clifford J.; Unkefer, Pat J.

    2013-05-21

    Transcriptional regulators (TRs) are an important and versatile group of proteins, yet very little progress has been achieved towards the discovery and annotation of their biological functions. We have characterized a previously unknown organic hydroperoxide resistance regulator from Burkholderia xenovoransLB400, Bxe_B2842, which is homologous to E. coli’s OhrR. Bxe_B2842 regulates the expression of an organic hydroperoxide resistance protein (OsmC). We utilized frontal affinity chromatography coupled with mass spectrometry (FAC-MS) and electrophoretic mobility gel shift assays (EMSA) to identify and characterize the possible effectors of the regulation by Bxe_B2842. Without an effector, Bxe_B2842 binds a DNA operator sequence (DOS) upstream ofmore » osmC. FAC-MS results suggest that 2-aminophenol binds to the protein and is potentially an effector molecule. EMSA analysis shows that 2-aminophenol also attenuates the Bxe_B2842’s affinity for its DOS. EMSA analysis also shows that organic peroxides attenuate Bxe_B2842/DOS affinity, suggesting that binding of the TR to its DOS is regulated by the two-cysteine mechanism, common to TRs in this family. Bxe_B2842 is the first OhrR TR to have both oxidative and effector-binding mechanisms of regulation. Our paper reveals further mechanistic diversity TR mediated gene regulation and provides insights into methods for function discovery of TRs.« less

  16. Beam position monitoring in the 100-MHz to 500-MHz frequency range using the log-ratio technique

    SciTech Connect (OSTI)

    Wells, F.D.; Shafer, R.E.; Gilpatrick, J.D.

    1993-05-01

    A logarithmic-ratio beam position monitor (BPM) circuit has been designed that operates directly from radio frequency- signals in the 100-MHz to 500-MHz frequency range. The circuit uses four logarithmic amplifiers, a pair for each channel. One amplifier per channel receives its signal input directly from a BPM electrode while the second amplifier receives the same signal attenuated by 7-dB. The two outputs of each channel are summed together and the composite video outputs are applied to a differencing amplifier. The net result is the logarithmic-ratio position measurement derived from the two input rf signals. Paralleling the pairs of outputs from the amplifiers provides measurement accuracy that is comparable to other circuit techniques used for position measurement.

  17. Beam position monitoring in the 100-MHz to 500-MHz frequency range using the log-ratio technique

    SciTech Connect (OSTI)

    Wells, F.D.; Shafer, R.E.; Gilpatrick, J.D.

    1993-01-01

    A logarithmic-ratio beam position monitor (BPM) circuit has been designed that operates directly from radio frequency- signals in the 100-MHz to 500-MHz frequency range. The circuit uses four logarithmic amplifiers, a pair for each channel. One amplifier per channel receives its signal input directly from a BPM electrode while the second amplifier receives the same signal attenuated by 7-dB. The two outputs of each channel are summed together and the composite video outputs are applied to a differencing amplifier. The net result is the logarithmic-ratio position measurement derived from the two input rf signals. Paralleling the pairs of outputs from the amplifiers provides measurement accuracy that is comparable to other circuit techniques used for position measurement.

  18. Advanced Photovoltaic Inverter Functionality using 500 kW Power Hardware-in-Loop Complete System Laboratory Testing: Preprint

    SciTech Connect (OSTI)

    Mather, B. A.; Kromer, M. A.; Casey, L.

    2013-01-01

    With the increasing penetration of distribution connected photovoltaic (PV) systems, more and more PV developers and utilities are interested in easing future PV interconnection concerns by mitigating some of the impacts of PV integration using advanced PV inverter controls and functions. This paper describes the testing of a 500 kW PV inverter using Power Hardware-in-Loop (PHIL) testing techniques. The test setup is described and the results from testing the inverter in advanced functionality modes, not commonly used in currently interconnected PV systems, are presented. PV inverter operation under PHIL evaluation that emulated both the DC PV array connection and the AC distribution level grid connection are shown for constant power factor (PF) and constant reactive power (VAr) control modes. The evaluation of these modes was completed under varying degrees of modeled PV variability.

  19. Alternate Multilayer Gratings with Enhanced Diffraction Efficiency in the 500-5000 eV Energy Domain

    SciTech Connect (OSTI)

    Polack, Francois; Lagarde, Bruno; Idir, Mourad; Cloup, Audrey Liard; Jourdain, Erick; Roulliay, Marc; Delmotte, Franck; Gautier, Julien; Ravet-Krill, Marie-Francoise

    2007-01-19

    An alternate multilayer (AML) grating is a 2 dimensional diffraction structure formed on an optical surface, having a 0.5 duty cycle in the in-plane and in the in-depth direction. It can be made by covering a shallow depth laminar grating with a multilayer stack. We show here that their 2D structure confer AML gratings a high angular and energetic selectivity and therefore enhanced diffraction properties, when used in grazing incidence. In the tender X-ray range (500eV - 5000 eV) they behave much like blazed gratings. Over 15% efficiency has been measured on a 1200 lines/mm Mo/Si AML grating in the 1.2 - 1.5 keV energy range. Computer simulations show that selected multilayer materials such as Cr/C should allow diffraction efficiency over 50% at photon energies over 3 keV.

  20. Radio frequency cavity analysis, measurement, and calibration of absolute Dee voltage for K-500 superconducting cyclotron at VECC, Kolkata

    SciTech Connect (OSTI)

    Som, Sumit; Seth, Sudeshna; Mandal, Aditya; Paul, Saikat; Duttagupta, Anjan

    2013-02-15

    Variable Energy Cyclotron Centre has commissioned a K-500 superconducting cyclotron for various types of nuclear physics experiments. The 3-phase radio-frequency system of superconducting cyclotron has been developed in the frequency range 9-27 MHz with amplitude and phase stability of 100 ppm and {+-}0.2{sup 0}, respectively. The analysis of the RF cavity has been carried out using 3D Computer Simulation Technology (CST) Microwave Studio code and various RF parameters and accelerating voltages ('Dee' voltage) are calculated from simulation. During the RF system commissioning, measurement of different RF parameters has been done and absolute Dee voltage has been calibrated using a CdTe X-ray detector along with its accessories and known X-ray source. The present paper discusses about the measured data and the simulation result.

  1. Ru/FeCoB double layered film with high in-plane magnetic anisotropy field of 500 Oe

    SciTech Connect (OSTI)

    Hirata, Ken-ichiro; Hashimoto, Atsuto; Matsuu, Toshimitsu; Nakagawa, Shigeki

    2009-04-01

    FeCoB layers prepared on Ru underlayer possess a high saturation magnetization M{sub s} and a high in-plane magnetic anisotropy filed H{sub k}. Effects of preparation conditions were investigated. Low Ar gas pressure condition and thicker film thickness were effective to attain distortion of FeCo crystallite. As the crystallinity of Ru underlayer became higher, higher H{sub k} was induced. The accumulation of anisotropic stress in the film caused by the oblique incidences of depositing atoms with high energy seems to be one of the important effects to attain high anisotropy field. It was succeeded to prepare the Ru/FeCoB film with high H{sub k} of 500 Oe.

  2. Surface analysis of Zircaloy-2 implanted with carbon before and after oxidation in air at 500 deg. C

    SciTech Connect (OSTI)

    Peng, D.Q. . E-mail: pdq01@mails.tsinghua.edu.cn; Bai, X.D.; Pan, F.; Sun, H.; Chen, B.S.

    2006-03-15

    Zircaloy-2 specimens were implanted with carbon ions in the fluence range from 1 x 10{sup 16} to 1 x 10{sup 18} ions/cm{sup 2}, using a MEVVA source at an extraction voltage of 40 kV at a maximum temperature of 380 deg. C. The valences and depth profiles of elements in the implanted surface of Zircaloy-2 were analyzed by X-ray photoelectron spectroscopy and Auger electron spectroscopy, respectively. Scanning electron microscopy was used to examine the micro-morphology of samples. The color of the oxidized samples was checked with an optical scanner. Glancing-angle X-ray diffraction at 0.3{sup o} incident angles was employed to examine the phase transformations of implanted samples before and after oxidation in the air at 500 deg. C for 2 h. Before oxidation, at fluences less than 5 x 10{sup 16} ions/cm{sup 2}, hexagonal zirconia (H-ZrO{sub 0.35}) was present. At a fluence of 1 x 10{sup 17} ions/cm{sup 2}, rhombohedral zirconia (R-Zr{sub 3}O) appeared. When the fluence reached 1 x 10{sup 18} ions/cm{sup 2}, cubic zirconium carbide was produced. There are many pits, both deep and shallow, in the sample surfaces, both prior to oxidation and after oxidation. Oxidation in the air at 500 deg. C gave rise to black surfaces on all samples. The X-ray diffraction results showed that monoclinic and tetragonal zirconia were present in the surface of as-received sample. For implanted samples, monoclinic and tetragonal zirconia are still present, while cubic zirconium carbide is produced at all fluences. The presence of ZrC is attributed to the high-temperature, long-time (2 h) exposure.

  3. SunShot-funded Advanced Inverter Testing Enables 2,500 Solar Energy Systems to Connect to Hawaiis Electric Grid

    Broader source: Energy.gov [DOE]

    Thanks to a SunShot collaboration at the Energy Departments National Renewable Energy Laboratory (NREL) more than 2,500 Hawaiian Electric customers will connect solar power to the electrical grid...

  4. Advanced, High-Reliability, System-Integrated 500kW PV Inverter Development: Final Subcontract Report, 29 September 2005 - 31 May 2008

    SciTech Connect (OSTI)

    West, R.

    2008-08-01

    Xantrex Technology accomplished subcontract goals of reducing parts cost, weight, and size of its 500-kW inverter by 25% compared to state-of-the-art PV inverters, while extending reliability by 25%.

  5. 2010 Dry and 2009 - 2010 Wet Season Branchiopod Survey Report, Site 300

    SciTech Connect (OSTI)

    Dexter, W

    2011-03-14

    Lawrence Livermore National Laboratory (LLNL) requested that Condor Country Consulting, Inc. (CCCI) perform wet season surveys and manage the dry season sampling for listed branchiopods in two ponded locations within the Site 300 Experimental Test Site. Site 300 is located in Alameda and San Joaquin Counties, located between the Cities of Livermore and Tracy. The two pool locations have been identified for possible amphibian enhancement activities in support of the Compensation Plan for impacts tied to the Building 850 soil clean-up project. The Building 850 project design resulted in formal consultation with the U.S. Fish and Wildlife Service (USFWS) as an amendment (File 81420-2009-F-0235) to the site-wide Biological Opinion (BO) (File 1-1-02-F-0062) in the spring of 2009 and requires mitigation for the California tiger salamander (AMCA, Ambystoma californiense) and California red-legged frog (CRLF, Rana draytonii) habitat loss. Both pools contain breeding AMCA, but do not produce metamorphs due to limited hydroperiod. The pool to the southeast (Pool BC-FS-2) is the preferred site for amphibian enhancement activities, and the wetland to northwest (Pool OA-FS-1) is the alternate location for enhancement. However, prior to enhancement, LLNL has been directed by USFWS (BO Conservation Measure 17 iii) to 'conduct USFWS protocol-level branchiopod surveys to determine whether listed brachiopod species are present within the compensation area.' CCCI conducted surveys for listed branchiopods in the 2009-2010 wet season to determine the presence of federally-listed branchiopods at the two pools (previous surveys with negative findings were performed by CCCI in 2001-2002 and 2002-2003 onsite). Surveys were conducted to partially satisfy the survey requirements of the USFWS 'Interim Survey Guidelines to Permittees for Recovery Permits under Section 10(a)(1)(A) of the Endangered Species Act for the Listed Vernal Pool Branchiopods' ('Guidelines, USFWS 1996 and BO Conservation Measure 17 iii). The dry sampling (included as an Appendix D) followed the wet season surveys in the summer of 2010.

  6. Structural properties of Sr{sub 0.61}Ba{sub 0.39}Nb{sub 2}O{sub 6} in the temperature range 10-500 K investigated by high-resolution neutron powder diffraction and specific heat measurements

    SciTech Connect (OSTI)

    Schefer, J.; Pomjakushin, V.; Stuhr, U.; Schaniel, D.; Woike, Th.; Petricek, V.; Woehlecke, M.; Imlau, M.

    2006-10-01

    We report high-resolution neutron powder diffraction on Sr{sub 0.61}Ba{sub 0.39}Nb{sub 2}O{sub 6} in the temperature range 15-500 K. The results indicate that the low-temperature anomalies (T{<=}100 K) observed in the dielectric dispersion are due to small changes in the incommensurate modulation of the NbO{sub 6} octahedra, as no structural phase transition of the average structure was observed. This interpretation is supported by specific heat measurements, which show no latent heat, but a glass-like behavior at low temperatures. Furthermore, we find that the structural changes connected with the ferroelectric phase transition at T{sub c}{approx_equal}350 K start already at 200 K, explaining the anisotropic thermal expansion in the temperature range 200-300 K observed in a recent x-ray diffraction study.

  7. EIS-0005-FS: Bonneville Power Administration Proposed FY 1979 Program, Facility Location on Supplement, Southwest Oregon Area Service, Buckley-Summer Lake 500 kV Line, Supplemental

    Broader source: Energy.gov [DOE]

    This Bonneville Power Administration document assesses the environmental impacts of constructing transmission facilities, which will coordinate with the Midpoint-Malin 500-kV line to be constructed by the Pacific Power and Light (PP&L) Company. The proposed action includes the construction of the 1.56-mile Buckley-Summer Lake 500-kV transmission line; the proposed Buckley Substation near Maupin, Oregon; and the proposed Summer Lake Substation near Silver Lake, Oregon.

  8. An observational study suggesting clinical benefit for adjuvant postoperative chemoradiation in a population of over 500 cases after gastric resection with D2 nodal dissection for adenocarcinoma of the stomach

    SciTech Connect (OSTI)

    Kim, Sung; Lim, Do Hoon; Lee, Jeeyun; Kang, Won Ki . E-mail: wkkang@smc.samsung.co.kr; MacDonald, John S.; Park, Chan Hyung; Park, Se Hoon; Lee, Se-Hoon; Kim, Kihyun; Park, Joon Oh; Kim, Won Seog; Jung, Chul Won; Park, Young Suk; Im, Young-Hyuck; Sohn, Tae Sung; Noh, Jae Hyung; Heo, Jin Seok; Kim, Yong Il; Park, Chul Keun; Park, Keunchil

    2005-12-01

    Purpose: The role of adjuvant chemoradiotherapy (CRT) in D2-resected gastric-cancer patients has not been defined yet. We investigated the effect of postoperative chemoradiotherapy on the relapse rate and survival rate of patients with D2-resected gastric cancer. Methods and Materials: From August 1995 to April 2001, 544 patients received postoperative CRT after curative D2 resection. During the same period of time, 446 patients received surgery without further adjuvant treatment. The adjuvant CRT consisted of 400 mg/m{sup 2} of fluorouracil plus 20 mg/m{sup 2} of leucovorin for 5 days, followed by 4,500 cGy of radiotherapy for 5 weeks, with fluorouracil and leucovorin on the first 4 and the last 3 days of radiotherapy. Two 5-day cycles of fluorouracil and leucovorin were given 4 weeks after the completion of radiotherapy. Results: The median duration of overall survival was significantly longer in the CRT group than in the comparison group (95.3 months vs. 62.6 months), which corresponds to a hazard ratio for death of 0.80 (p = 0.0200) or a reduction of 20% in the risk of death in the CRT group. The 5-year survival rates were consistently longer in the CRT group at Stages II, IIIA, IIIB, and IV than those in the comparison group. The CRT was associated with increases in the median duration of relapse-free survival (75.6 months vs. 52.7 months; hazard ratio for relapse, 0.80, p = 0.0160). Conclusion: Our results highly suggest that the postoperative chemoradiotherapy in D2-resected gastric-cancer patients can prolong survival and decrease recurrence.

  9. Communication across 300 generations: deterring human interference with waste deposit sites

    SciTech Connect (OSTI)

    Tannenbaum, P.H.

    1984-04-01

    The conditions attendant on the deep land burial of nuclear waste products raise a number of possible scenarios to cover the necessary 10,000 years of burial. However, no matter what kind of futuristic scenario obtains, it is desirable to develop an information system indicating the locale and nature of the deposit site and the types of materials stored, along with forewarnings not to interefere with the sites. A variety of such informational sites are suggested. Attention then turns to the recipients of such messages, recognizing from the outset that the psychological/perceptual makeup of individuals across the next 300 or so generations is virtually impossible to predict, particularly since new technologies may well alter that makeup in the furture. Nevertheless, current evidence suggests that certain human characteristics may be considered universal, and that these suggest the incorporation of selected sign signification into the message system. There are other such characteristics that, while probably not intrinsic, can probably be acquired with a minimum of formal training. That still leaves much of the message content to be deliberately created and, hence, learned. The common trefoil or other developed biohazardous signs emerge as the best candidates for a generic base symbol for the buried material.

  10. Degradation of different elastomeric polymers in simulated geothermal environments at 300°C

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Sugama, Toshifumi; Pyatina, Tatiana; Redline, Erica Marie; McElhanon, James R.; Blankenship, Douglas A.

    2015-07-17

    This study evaluates the degradation of six different elastomeric polymers used for O-rings: EPDM, FEPM, type I- and II-FKM, FFKM, and FSR, in five different simulated geothermal environments at 300 °C: 1) non-aerated steam/cooling cycles, 2) aerated steam/cooling cycles, 3) water-based drilling fluid, 4) CO2-rich geo-brine fluid, and, 5) heat–cool water quenching cycles. The factors assessed included the extent of oxidation, changes in thermal behavior, micro-defects, permeation of ionic species from the test environments into the O-rings, silicate-related scale-deposition, and changes in the O-rings' elastic modulus. The reliability of the O-rings to maintain their integrity depended on the elastomeric polymermore » composition and the exposure environment. FSR disintegrated while EPDM was oxidized only to some degree in all the environments, FKM withstood heat-water quenching but underwent chemical degradation, FEPM survived in all the environments with the exception of heat-water quenching where it underwent severe oxidation-induced degradation, and FFKM displayed outstanding compatibility with all the tested environments. This study discusses the degradation mechanisms of the polymers under the aforementioned conditions.« less

  11. Integrity assessment plan for PNL 300 area radioactive hazardous waste tank system. Final report

    SciTech Connect (OSTI)

    1996-03-01

    The Pacific Northwest Laboratory (PNL), operated by Battelle Memorial Institute under contract to the U.S. Department of Energy, operates tank systems for the U.S. Department of Energy, Richland Operations Office (DOE-RL), that contain dangerous waste constituents as defined by Washington State Department of Ecology (WDOE) Dangerous Waste Regulations, Washington Administrative Code (WAC) 173-303-040(18). Chapter 173-303-640(2) of the WAC requires the performance of integrity assessments for each existing tank system that treats or stores dangerous waste, except those operating under interim status with compliant secondary containment. This Integrity Assessment Plan (IAP) identifies all tasks that will be performed during the integrity assessment of the PNL-operated Radioactive Liquid Waste Systems (RLWS) associated with the 324 and 325 Buildings located in the 300 Area of the Hanford Site. It describes the inspections, tests, and analyses required to assess the integrity of the PNL RLWS (tanks, ancillary equipment, and secondary containment) and provides sufficient information for adequate budgeting and control of the assessment program. It also provides necessary information to permit the Independent, Qualified, Registered Professional Engineer (IQRPE) to approve the integrity assessment program.

  12. Degradation of different elastomeric polymers in simulated geothermal environments at 300°C

    SciTech Connect (OSTI)

    Sugama, Toshifumi; Pyatina, Tatiana; Redline, Erica Marie; McElhanon, James R.; Blankenship, Douglas A.

    2015-07-17

    This study evaluates the degradation of six different elastomeric polymers used for O-rings: EPDM, FEPM, type I- and II-FKM, FFKM, and FSR, in five different simulated geothermal environments at 300 °C: 1) non-aerated steam/cooling cycles, 2) aerated steam/cooling cycles, 3) water-based drilling fluid, 4) CO2-rich geo-brine fluid, and, 5) heat–cool water quenching cycles. The factors assessed included the extent of oxidation, changes in thermal behavior, micro-defects, permeation of ionic species from the test environments into the O-rings, silicate-related scale-deposition, and changes in the O-rings' elastic modulus. The reliability of the O-rings to maintain their integrity depended on the elastomeric polymer composition and the exposure environment. FSR disintegrated while EPDM was oxidized only to some degree in all the environments, FKM withstood heat-water quenching but underwent chemical degradation, FEPM survived in all the environments with the exception of heat-water quenching where it underwent severe oxidation-induced degradation, and FFKM displayed outstanding compatibility with all the tested environments. This study discusses the degradation mechanisms of the polymers under the aforementioned conditions.

  13. Puerto Rico and U.S. Virgin Islands Wind Resource Map at 50 meters

    Wind Powering America (EERE)

    % % % % % % % % % % % % % % % % % % % % % 19-JUN-2007 1.1.1 U.S. Department of Energy National Renewable Energy Laboratory Puerto Rico and U.S. Virgin Islands - 50 m Wind Power Mayaguez 20 0 20 40 60 80 100 Kilometers 20 0 20 40 60 Miles Ponce San Juan Charlotte Amalie Cruz Bay PUERTO RICO VIRGIN ISLANDS Wind Power Class 1 2 3 4 5 Resource Potential Poor Marginal Fair Good Excellent Wind Power Density at 50 m W/m 0 - 200 200 - 300 300 - 400 400 - 500 500 - 600 2 Wind Speed at 50 m m/s 0.0 - 5.9

  14. Characterization of the Hanford 300 area burial grounds. Final report: decontamination and decommissioning

    SciTech Connect (OSTI)

    Phillips, S.J.; Ames, L.L.; Fitzner, R.E.; Gee, G.W.; Sandness, G.A.; Simmons, C.S.

    1980-01-01

    Pacific Northwest Laboratory conducted a series of investigations at the Hanford Site to develop technologies for characterizing and monitoring radioactive waste burial facilities that could be used in determining appropriate decommissioning alternatives. Specific objectives were to develop unique functional geophysics, geochemical, soil physics, numerical modeling, and biological methodologies needed to better characterize and monitor buried radioactive waste disposal sites. To meet these objectives the project was divided into four tasks: Task I, Geophysical Evaluation - Geophysical surveys were taken to locate and define the gross composition of waste materials. Task II, Geochemical Analysis - The interaction of disposed radionuclides with geologic media was analyzed through an integrated radiochemical procedure. Task III, Fluid Transport and Modeling - Computer modeling of water migration in partially saturated groundwater systems was verified with actual data collected at a field test facility used to monitor micrometeorological and geohydrological energy and mass transfer factors. Task IV, Biological Transport - Several biological organisms were evaluated for potential radionuclide uptake and transport. Along with the four tasks, the project included a review of pertinent literature and regulatory issues that might affect the alternatives selected. Surveys were taken of the surrounding area and specific sites and operations. The overall results indicated that the 300 Area Burial Grounds have been adequate in containing radioactive waste. Based on the results of the project, the alternatives identified for decommissioning these sites are exhumation and translocation, entombment, perpetual care, and abandonment. Perpetual care (currently used) appears to be the best decommissioning alternative for these burial grounds at this time. However, another alternative may be selected depending on future waste management policies, plans, or activities.

  15. Measurement of Activation Reaction Rate Distributions in a Lead Assembly Bombarded with 500-MeV Protons

    SciTech Connect (OSTI)

    Takada, Hiroshi; Meigo, Shin-ichro; Sasa, Toshinobu; Tsujimoto, Kazufumi; Yasuda, Hideshi

    2000-05-15

    Reaction rate distributions of various activation detectors such as the {sup nat}Ni(n,x){sup 58}Co, {sup 197}Au(n,2n){sup 196}Au, and {sup 197}Au(n,4n){sup 194}Au reactions were measured to study the production and the transport of spallation neutrons in a lead assembly bombarded with protons of 500 MeV. The measured data were analyzed with the nucleon-meson transport code NMTC/JAERI combined with the MCNP4A code using the nuclide production cross sections based on the JENDL Dosimetry File and those calculated with the ALICE-F code. It was found that the NMTC/JAERI-MCNP4A calculations agreed well with the experiments for the low-energy-threshold reaction of {sup nat}Ni(n,x){sup 58}Co. With the increase of threshold energy, however, the calculation underestimated the experiments, especially above 20 MeV. The reason for the disagreement can be attributed to the underestimation of the neutron yield in the tens of mega-electron-volt regions by the NMTC/JAERI code.

  16. NMR Analysis of Methyl Groups at 100-500 kDa: Model Systems and Arp2/3 Complex

    SciTech Connect (OSTI)

    Kreishman-Deitrick, Mara; Egile, Coumaran; Hoyt, David W.; Ford, Joseph J.; Rong, Li; Rosen, Michael K.

    2003-07-01

    Large macromolecular machines are among the most important and challenging targets for structural and mechanistic analyses. Consequently, there is great interest in development of NMR methods for the study of multicomponent systems in the 50-500 kDa range. Biochemical methods also must be developed in concert to produce such systems in selectively labeled form. Here, we present 1H/13C-HSQC spectra of protonated methyl groups in a model system that mimics molecular weights up to ~560 kDa. Signals from side chain methyl groups of Ile, Leu, and Val residues are clearly detectable at correlation times up to ~330 ns. We have also developed a biochemical procedure to produce the 240 kDa, heteroheptameric Arp2/3 actin nucleation complex selectively labeled at one subunit and obtained 1H/13C-HSQC spectra of this assembly. Sensitivity in spectra of both the Arp2/3 complex and the model system indicate that methyl groups will be useful sources of information in nonsymmetric systems with molecular weights greater than 600 kDa at concentrations less than 100 μM. Methyl analyses will complement TROSY and CRINEPT analyses of amides in NMR studies of structure and molecular interactions of extremely large macromolecules and assemblies.

  17. 500-MHz x-ray counting with a Si-APD and a fast-pulse processing system

    SciTech Connect (OSTI)

    Kishimoto, Shunji; Taniguchi, Takashi; Tanaka, Manobu

    2010-06-23

    We introduce a counting system of up to 500 MHz for synchrotron x-ray high-rate measurements. A silicon avalanche photodiode detector was used in the counting system. The fast-pulse circuit of the amplifier was designed with hybrid ICs to prepare an ASIC system for a large-scale pixel array detector in near future. The fast amplifier consists of two cascading emitter-followers using 10-GHz band transistors. A count-rate of 3.25x10{sup 8} s{sup -1} was then achieved using the system for 8-keV x-rays. However, a baseline shift by adopting AC-coupling in the amplifier disturbed us to observe the maximum count of 4.49x10{sup 8} s{sup -1}, determined by electron-bunch filling into a ring accelerator. We also report that an amplifier with a baseline restorer was tested in order to keep the baseline level to be 0 V even at high input rates.

  18. Acceleration of 500 keV Negative Ion Beams By Tuning Vacuum Insulation Distance On JT-60 Negative Ion Source

    SciTech Connect (OSTI)

    Kojima, A.; Hanada, M.; Tanaka, Y.; Taniguchi, M.; Kashiwagi, M.; Inoue, T.; Umeda, N.; Watanabe, K.; Tobari, H.; Kobayashi, S.; Yamano, Y.; Grisham, L. R.

    2011-09-26

    Acceleration of a 500 keV beam up to 2.8 A has been achieved on a JT-60U negative ion source with a three-stage accelerator by overcoming low voltage holding which is one of the critical issues for realization of the JT-60SA ion source. In order to improve the voltage holding, preliminary voltage holding tests with small-size grids with uniform and locally intense electric fields were carried out, and suggested that the voltage holding was degraded by both the size and local electric field effects. Therefore, the local electric field was reduced by tuning gap lengths between the large size grids and grid support structures of the accelerator. Moreover, a beam radiation shield which limited extension of the minimum gap length was also optimized so as to reduce the local electric field while maintaining the shielding effect. These modifications were based on the experiment results, and significantly increased the voltage holding from <150 kV/stage for the original configuration to 200 kV/stage. These techniques for improvement of voltage holding should also be applicable to other large ion sources accelerators such as those for ITER.

  19. Absorption of a single 500 fs laser pulse at the surface of fused silica: Energy balance and ablation efficiency

    SciTech Connect (OSTI)

    Varkentina, N.; Sanner, N.; Lebugle, M.; Sentis, M.; Utéza, O.

    2013-11-07

    Ablation of fused silica by a single femtosecond laser pulse of 500 fs pulse duration is investigated from the perspective of efficiency of incident photons to remove matter. We measure the reflected and transmitted fractions of the incident pulse energy as a function of fluence, allowing us to recover the evolution of absorption at the material surface. At the ablation threshold fluence, 25% of incident energy is absorbed. At high fluences, this ratio saturates around 70% due to the appearance of a self-triggered plasma mirror (or shielding) effect. By using the energy balance retrieved experimentally and measurements of the ablated volume, we show that the amount of absorbed energy is far above the bonding energy of fused silica at rest and also above the energy barrier to ablate the material under non-equilibrium thermodynamic conditions. Our results emphasize the crucial role of transient plasma properties during the laser pulse and suggest that the major part of the absorbed energy has been used to heat the plasma formed at the surface of the material. A fluence range yielding an efficient and high quality ablation is also defined, which makes the results relevant for femtosecond micromachining processes.

  20. Seasonal Patterns of Melatonin, Cortisol, and Progesterone Secretion in Female Lambs Raised Beneath a 500-kV Transmission Line.

    SciTech Connect (OSTI)

    Lee, Jack M.

    1992-06-01

    Although several kinds of biological effects of electric and magnetic fields have been reported from laboratory studies, few have been independently replicated. When this study was being planned, the suppression of nighttime melatonin in rodents was thought to represent one of the strongest known effects of these fields. The effect had been replicated by a single laboratory for 60-Hz electric fields, and by multiple laboratories for d-c magnetic fields. The primary objective of this study was to determine whether the effect of electric and magnetic fields on melatonin would also occur in sheep exposed to a high voltage transmission line. The specific hypothesis tested by this experiment was as follows: The electrical environment produced by a 60-Hz, 500-kV transmission line causes a depression in nocturnal melatonin in chronically exposed female lambs. This may mimic effects of pinealectomy or constant long-day photoperiods, thus delaying the onset of reproductive cycles. Results of the study do not provide evidence to support the hypothesis. Melatonin concentrations in the sheep exposed to the transmission line showed the normal pattern of low daytime and high nighttime serum levels. As compared to the control group, there were no statistically significant group differences in the mean amplitude, phase, or duration of the nighttime melatonin elevation.

  1. Identification of non-ordinary mesons from the dispersive connection between their poles and their Regge trajectories: The f{sub 0}(500) resonance

    SciTech Connect (OSTI)

    Pelaez, J. R.; Londergan, J. T.; Nebreda, J.; Szczepaniak, Adam P.

    2014-02-01

    We show how the Regge trajectory of a resonance can be obtained from its pole in a scattering process and analytic constraints in the complex angular momentum plane. The method is suited for resonances that dominate an elastic scattering amplitude. In particular, from the {rho}(770) resonance pole in {pi}{pi} scattering, we obtain its linear Regge trajectory, characteristic of ordinary quark–antiquark states. In contrast, the f{sub 0}(500) pole—the sigma meson—which dominates scalar isoscalar {pi}{pi} scattering, yields a nonlinear trajectory with a much smaller slope at the f{sub 0}(500) mass. Conversely, imposing a linear Regge trajectory for the f{sub 0}(500), with a slope of typical size, yields an elastic amplitude at odds with the data. This provides strong support for the non-ordinary nature of the sigma meson.

  2. Design of a self-aligned, wide temperature range (300 mK-300 K) atomic force microscope/magnetic force microscope with 10 nm magnetic force microscope resolution

    SciTech Connect (OSTI)

    Karc?, zgr; Dede, Mnir

    2014-10-01

    We describe the design of a wide temperature range (300 mK-300 K) atomic force microscope/magnetic force microscope with a self-aligned fibre-cantilever mechanism. An alignment chip with alignment groves and a special mechanical design are used to eliminate tedious and time consuming fibre-cantilever alignment procedure for the entire temperature range. A low noise, Michelson fibre interferometer was integrated into the system for measuring deflection of the cantilever. The spectral noise density of the system was measured to be ~12 fm/?Hz at 4.2 K at 3 mW incident optical power. Abrikosov vortices in BSCCO(2212) single crystal sample and a high density hard disk sample were imaged at 10 nm resolution to demonstrate the performance of the system.

  3. Tracking in full Monte Carlo detector simulations of 500 GeV e{sup +}e{sup {minus}} collisions

    SciTech Connect (OSTI)

    Ronan, M.T.

    2000-03-01

    In full Monte Carlo simulation models of future Linear Collider detectors, charged tracks are reconstructed from 3D space points in central tracking detectors. The track reconstruction software is being developed for detailed physics studies that take realistic detector resolution and background modeling into account. At this stage of the analysis, reference tracking efficiency and resolutions for ideal detector conditions are presented. High performance detectors are being designed to carry out precision studies of e{sup +}e{sup {minus}} annihilation events in the energy range of 500 GeV to 1.5 TeV. Physics processes under study include Higgs mass and branching ratio measurements, measurement of possible manifestations of Supersymmetry (SUSY), precision Electro-Weak (EW) studies and searches for new phenomena beyond their current expectations. The relatively-low background machine environment at future Linear Colliders will allow precise measurements if proper consideration is given to the effects of the backgrounds on these studies. In current North American design studies, full Monte Carlo detector simulation and analysis is being used to allow detector optimization taking into account realistic models of machine backgrounds. In this paper the design of tracking software that is being developed for full detector reconstruction is discussed. In this study, charged tracks are found from simulated space point hits allowing for the straight-forward addition of background hits and for the accounting of missing information. The status of the software development effort is quantified by some reference performance measures, which will be modified by future work to include background effects.

  4. WARMAdvantage Program | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    500 Geothermal Heat Pump: 500 Heat Pump: 500 Residential Gas Customers (including propane): Gas Furnace: 250- 500 Gas Furnace (ENERGY STAR qualified): 500 Gas Boiler: 300...

  5. Final Hazard Categorization for the Remediation of Six 300-FF-2 Operable Unit Solid Waste Burial Grounds

    SciTech Connect (OSTI)

    J. D. Ludowise

    2006-12-12

    This report provides the final hazard categorization (FHC) for the remediation of six solid waste disposal sites (referred to as burial grounds) located in the 300-FF-2 Operable Unit (OU) on the Hanford Site. These six sites (618-1, 618-2, 618-3, 618-7, 618-8, and 618-13 Burial Grounds) were determined to have a total radionuclide inventory (WCH 2005a, WCH 2005d, WCH 2005e and WCH 2006b) that exceeds the DOE-STD-1027 Category 3 threshold quantity (DOE 1997) and are the subject of this analysis. This FHC document examines the hazards, identifies appropriate controls to manage the hazards, and documents the FHC and commitments for the 300-FF-2 Burial Grounds Remediation Project.

  6. Microsoft Word - Environmental Review of B832 Canyon at LLNL Site 300 2.24.11.doc

    National Nuclear Security Administration (NNSA)

    Department of Energy News Media Contact For Immediate Release John Belluardo February 25, 2011 (925) 422-2567 ENVIRONMENTAL REVIEW OF THE BUILDING 832 CANYON OPERABLE UNIT AT LAWRENCE LIVERMORE NATIONAL LABORATORY'S SITE 300 BY U.S. DEPARTMENT OF ENERGY/NATIONAL NUCLEAR SECURITY ADMINISTRATION STARTED Livermore, CA -- The U.S. Department of Energy (DOE) /National Nuclear Security Administration has begun the first Five-Year Review of its environmental cleanup of the Building 832 Canyon Operable

  7. Increasing the reliability of the shutdown of 500 - 750-kV overhead lines equipped with shunt reactors in an unsuccessful three-phase automatic repeated closure cycle

    SciTech Connect (OSTI)

    Kuz'micheva, K. I.; Merzlyakov, A. S.; Fokin, G. G.

    2013-05-15

    The reasons for circuit-breaker failures during repeated disconnection of 500 - 750 kV overhead lines with shunt reactors in a cycle of unsuccessful three-phase automatic reconnection (TARC) are analyzed. Recommendations are made for increasing the operating reliability of power transmission lines with shunt reactors when there is unsuccessful reconnection.

  8. EIS-0032: 500 kV International Transmission Line NSP-TR-1, Forbes, Minnesota to Manitoba, Canada, Northern States Power Company

    Broader source: Energy.gov [DOE]

    The Economic Regulatory Administration developed this EIS to evaluate the environmental impacts of a 500-kilovolt transmission line proposed by the Northern States Power Company to provide a transmission facility for the exchange of electrical energy between Canada and the United States.

  9. Baseline System Costs for 50.0 MW Enhanced Geothermal System--A Function of: Working Fluid, Technology, and Location, Location, Location

    Broader source: Energy.gov [DOE]

    Project objectives: Develop a baseline cost model of a 50.0 MW Enhanced Geothermal System, including all aspects of the project, from finding the resource through to operation, for a particularly challenging scenario: the deep, radioactively decaying granitic rock of the Pioneer Valley in Western Massachusetts.

  10. Determination of partial-wave inelasticities for elastic pion-nucleon scattering with the aid of experimental data on {pi}N {yields} {pi}{pi}N processes in the beam-momentum range 300 < P{sub beam} < 500 MeV/c

    SciTech Connect (OSTI)

    Kozhevnikov, V. A.; Sherman, S. G.

    2008-11-15

    The partial-wave inelasticity parameters of the amplitude for elastic pion-nucleon scattering are determined with the aid of the phenomenological amplitude for inelastic {pi}N {yields} {pi}{pi}N processes in the energy range extending to the threshold for the production of two pions. The resulting inelasticity parameters are compared with their counterparts derived from modern partial-wave analyses. The largest inelastic-scattering cross section in the P11 wave is in excellent agreement with the analogous value from the analysis performed at the George Washington University in 2006. For other waves, however, the present results differ in the majority of cases from respective values given by partial-wave analyses (the distinctions are especially large for the isospin-3/2 amplitudes).

  11. Development of a 400 Level 3C Clamped Downhole Seismic Receiver Array for 3D Borehole Seismic Imaging of Gas Reservoirs

    SciTech Connect (OSTI)

    Bjorn N. P. Paulsson

    2006-09-30

    Borehole seismology is the highest resolution geophysical imaging technique available today to the oil and gas industry for characterization and monitoring of oil and gas reservoirs. However, the industry's ability to perform high resolution 3D imaging of deep and complex gas reservoirs using borehole seismology has been hampered by the lack of acquisition technology necessary to record large volumes of high frequency, high signal-to-noise-ratio borehole seismic data. This project took aim at this shortcoming by developing a 400 level 3C clamped downhole seismic receiver array, and accompanying software, for borehole seismic 3D imaging. This large borehole seismic array has removed the technical acquisition barrier for recording the data volumes necessary to do high resolution 3D VSP and 3D cross-well seismic imaging. Massive 3D VSP{reg_sign} and long range Cross-Well Seismology (CWS) are two of the borehole seismic techniques that promise to take the gas industry to the next level in their quest for higher resolution images of deep and complex oil and gas reservoirs. Today only a fraction of the oil or gas in place is produced when reservoirs are considered depleted. This is primarily due to our lack of understanding of detailed compartmentalization of oil and gas reservoirs. In this project, we developed a 400 level 3C borehole seismic receiver array that allows for economic use of 3D borehole seismic imaging for reservoir characterization and monitoring. This new array has significantly increased the efficiency of recording large data volumes at sufficiently dense spatial sampling to resolve reservoir complexities. The receiver pods have been fabricated and tested to withstand high temperature (200 C/400 F) and high pressure (25,000 psi), so that they can operate in wells up to 7,620 meters (25,000 feet) deep. The receiver array is deployed on standard production or drill tubing. In combination with 3C surface seismic or 3C borehole seismic sources, the 400 level receiver array can be used to obtain 3D 9C data. These 9C borehole seismic data provide both compressional wave and shear wave information that can be used for quantitative prediction of rock and pore fluid types. The 400-level borehole receiver array has been deployed successfully in a number of oil and gas wells during the course of this project, and each survey has resulted in marked improvements in imaging of geologic features that are critical for oil or gas production but were previously considered to be below the limits of seismic resolution. This added level of reservoir detail has resulted in improved well placement in the oil and gas fields that have been drilled using the Massive 3D VSP{reg_sign} images. In the future, the 400-level downhole seismic receiver array is expected to continue to improve reservoir characterization and drilling success in deep and complex oil and gas reservoirs.

  12. Studies and optimization of Pohang Light Source-II superconducting radio frequency system at stable top-up operation with beam current of 400 mA

    SciTech Connect (OSTI)

    Joo, Youngdo Yu, Inha; Park, Insoo; Chun, Myunghwan; Lee, Byung-Joon; Hwang, Ilmoon; Ha, Taekyun; Shin, Seunghwan; Sohn, Younguk

    2014-12-21

    After three years of upgrading work, the Pohang Light Source-II (PLS-II) is now successfully operating. The final quantitative goal of PLS-II is a top-up user-service operation with beam current of 400 mA to be completed by the end of 2014. During the beam store test up to 400 mA in the storage ring (SR), it was observed that the vacuum pressure around the radio frequency (RF) window of the superconducting cavity rapidly increases over the interlock level limiting the availability of the maximum beam current storing. Although available beam current is enhanced by setting a higher RF accelerating voltage, it is better to keep the RF accelerating voltage as low as possible in the long time top-up operation. We investigated the cause of the window vacuum pressure increment by studying the changes in the electric field distribution at the superconducting cavity and waveguide according to the beam current. In our simulation, an equivalent physical modeling was developed using a finite-difference time-domain code. The simulation revealed that the electric field amplitude at the RF window is exponentially increased as the beam current increases, thus this high electric field amplitude causes a RF breakdown at the RF window, which comes with the rapid increase of window vacuum pressure. The RF accelerating voltage of PLS-II RF system was set to 4.95 MV, which was estimated using the maximum available beam current that works as a function of RF voltage, and the top-up operation test with the beam current of 400 mA was successfully carried out.

  13. INFLUENCE OF CARBON AND DPA RATE ON NEUTRON-INDUCED SWELLING OF Fe-15Cr-16Ni-0.25Ti IN FFTF AT ~400 DEGREES C

    SciTech Connect (OSTI)

    Okita, Taira; Sekimura, Naoto; Garner, Francis A.; Wolfer, W. G.

    2002-12-31

    The purpose of this effort is to determine the influence of dpa rate and composition on the void swelling of simple austenitic Fe-Cr-Ni alloys. Contrary to the swelling behavior of fcc Fe-15Cr-16Ni and Fe-15Cr-16Ni-0.25Ti alloys irradiated in the same FFTF-MOTA experiment, Fe-15Cr-16Ni-0.25Ti-0.04C does not exhibit a dependence of swelling on dpa rate at approximately 400 degrees C. The transient regime of swelling is prolonged by carbon addition, however.

  14. {open_quotes}In-situ{close_quotes} stress-relieving of Ni/Cu alloy 400 tubed high pressure feedwater heaters

    SciTech Connect (OSTI)

    Rahoi, D.W.

    1995-12-01

    One of the known failure methods of Ni/Cu Alloy 400 is stress-corrosion cracking. When it can be determined with physical evidence that this is occurring, it may be possible to arrest or, at least slow down the failure methods by performing an {open_quotes}in situ{close_quotes} stress relief using plant steam. This paper does not recommend how to do it, but does reveal there is some hope the relief-anneal slows down the failure rate and increases the heater life, by reducing residual stress.

  15. Modeling the Thermal Mechanical Behavior of a 300 K Vacuum Vesselthat is Cooled by Liquid Hydrogen in Film Boiling

    SciTech Connect (OSTI)

    Yang, S.Q.; Green, M.A.; Lau, W.

    2004-05-07

    This report discusses the results from the rupture of a thin window that is part of a 20-liter liquid hydrogen vessel. This rupture will spill liquid hydrogen onto the walls and bottom of a 300 K cylindrical vacuum vessel. The spilled hydrogen goes into film boiling, which removes the thermal energy from the vacuum vessel wall. This report analyzes the transient heat transfer in the vessel and calculates the thermal deflection and stress that will result from the boiling liquid in contact with the vessel walls. This analysis was applied to aluminum and stainless steel vessels.

  16. Atomic Number Dependence of Hadron Production at Large Transverse Momentum in 300 GeV Proton--Nucleus Collisions

    DOE R&D Accomplishments [OSTI]

    Cronin, J. W.; Frisch, H. J.; Shochet, M. J.; Boymond, J. P.; Mermod, R.; Piroue, P. A.; Sumner, R. L.

    1974-07-15

    In an experiment at the Fermi National Accelerator Laboratory we have compared the production of large transverse momentum hadrons from targets of W, Ti, and Be bombarded by 300 GeV protons. The hadron yields were measured at 90 degrees in the proton-nucleon c.m. system with a magnetic spectrometer equipped with 2 Cerenkov counters and a hadron calorimeter. The production cross-sections have a dependence on the atomic number A that grows with P{sub 1}, eventually leveling off proportional to A{sup 1.1}.

  17. Generation of 500 MeV-1 GeV energy electrons from laser wakefield acceleration via ionization induced injection using CO{sub 2} mixed in He

    SciTech Connect (OSTI)

    Mo, M. Z.; Ali, A.; Fedosejevs, R.; Fourmaux, S.; Lassonde, P.; Kieffer, J. C.

    2013-04-01

    Laser wakefield acceleration of 500 MeV to 1 GeV electron bunches has been demonstrated using ionization injection in mixtures of 4% to 10% of CO{sub 2} in He. 80 TW laser pulses were propagated through 5 mm gas jet targets at electron densities of 0.4-1.5 Multiplication-Sign 10{sup 19}cm{sup -3}. Ionization injection led to lower density thresholds, a higher total electron charge, and an increased probability of producing electrons above 500 MeV in energy compared to self-injection in He gas alone. Electrons with GeV energies were also observed on a few shots and indicative of an additional energy enhancement mechanism.

  18. U. S. Energy Information Administration | Drilling Productivity...

    U.S. Energy Information Administration (EIA) Indexed Site

    Utica Region 0 100 200 300 400 500 600 2007 2008 2009 2010 2011 2012 2013 2014 2015 2016 Oil production thousand barrelsday Utica Region -2.0 0.0 2.0 4.0 6.0 May 79 Mbbld ...

  19. Slide 1

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    - diffusion capacitance C T (V) - transition capacitance V ac - arcing AC voltage - signal frequency -8.00E+03 -7.00E+03 -6.00E+03 -5.00E+03 -4.00E+03 -3.00E+03 -2.00E+03...

  20. RangeTables.xls

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    (MeVcmmg) LET vs. Range in Si for 25 MeV SEE Beams (low LET) 4 He 14 N 0 0.5 1 1.5 0 600 1200 1800 2400 3000 3600 4 He 14 N 22 Ne 0 1 2 3 4 5 6 7 8 9 10 0 100 200 300 400 500...

  1. From the Woods to the Refinery

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    ... 1 MJ biofuel from unmanaged hardwood -3E-16 -2E-16 -1E-16 0 1E-16 2E-16 3E-16 4E-16 5E-16 0 100 200 300 400 500 GWI inst W.m -2 Years Plant at zero Cut at zero Where do we go ...

  2. BPA-2011-00698-FOIA Response

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    1211 16:00 1211 17:00 1211 18:00 1211 19:00 1211 20:00 1211 21:00 1211 22:00 1211 23:00 1311 0:00 1311 1:00 1311 2:00 1311 3:00 1311 4:00 1311 5:00...

  3. untitled

    Office of Legacy Management (LM)

    BETATRON BUILDING Granite City Site M:\LTS\111\0001\10\000\S08243\S0824300-15.mxd coatesc 03/08/2012 11:46:01 AM Granite City Site Granite City, Illinois, Site 2011 Aerial Photo 2007 Aerial Photo 0 500 1,000 100 200 300 400 Feet

  4. BPA-2012-01927-FOIA Response

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    at (503) 230-5102) 3:00pm 5:00pm CFO Interview 3 (719) 12:00pm 1:00pm EE Lessons Learned Report (Room 606) 1:30pm 4:00pm CFO to Present 2011 Financial Statement Package for...

  5. Automatic system for regulating the frequency and power of the 500 MW coal-dust power generating units at the Reftinskaya GRES

    SciTech Connect (OSTI)

    Bilenko, V. A.; Gal'perina, A. I.; Mikushevich, E. E.; Nikol'skii, D. Yu.; Zhugrin, A. G.; Bebenin, P. A.; Syrchin, M. V.

    2009-03-15

    The monitoring and control systems at the 500 MW coal-dust power generating units No. 7, 8, and 9 at the Reftinskaya GRES have been modernized using information-regulator systems. Layouts for instrumental construction of these systems and expanded algorithmic schemes for the automatic frequency and power control system and for the boiler supply and fuelling are discussed. Results from tests and normal operation of the automatic frequency and power control system are presented.

  6. Commissioning of the 112 MHz SRF Gun and 500 MHz bunching cavities for the CeC PoP Linac

    SciTech Connect (OSTI)

    Belomestnykh, S.; Ben-Zvi, I.; Brutus, J. C.; Litvinenko, V.; McIntosh, P.; Moss, A.; Narayan, G.; Orfin, P.; Pinayev, I.; Rao, T.; Skaritka, J.; Smith, K.; Than, R.; Tuozzolo, J.; Wang, E.; Wheelhouse, A.; Wu, Q.; Xiao, B.; Xin, T.; Xu, W.; Zaltsman, A.

    2015-05-03

    The Coherent electron Cooling Proof-of-Principle (CeC PoP) experiment at BNL includes a short electron linac. During Phase 1, a 112 MHz superconducting RF photo-emission gun and two 500 MHz normal conducting bunching cavities were installed and are under commissioning. The paper describes the Phase1 linac layout and presents commissioning results for the cavities and associated RF, cryogenic and other sub-systems

  7. Evaluated Mean Values and Covariances for the Prompt Fission Neutron Spectrum of 239Pu induced by neutrons of 500 keV

    SciTech Connect (OSTI)

    Neudecker, Denise

    2014-07-10

    This document provides the numerical values of the evaluated prompt fission neutron spectrum for 239Pu induced by neutrons of 500 keV as well as relative uncertainties and correlations. This document also contains a short description how these data were obtained and shows plots comparing the evaluated results to experimental information as well as the corresponding ENDF/B-VII.1 evaluation.

  8. Site 300 hazardous-waste-assessment project. Interim report: December 1981. Preliminary site reconnaissance and project work plan

    SciTech Connect (OSTI)

    Raber, E.; Helm, D.; Carpenter, D.; Peifer, D.; Sweeney, J.

    1982-01-20

    This document was prepared to outline the scope and objectives of the Hazardous Waste Assessment Project (HWAP) at Site 300. This project was initiated in October, 1981, to investigate the existing solid waste landfills in an effort to satisfy regulatory guidelines and assess the potential for ground-water contamination. This involves a site-specific investigation (utilizing geology, hydrology, geophysics and geochemistry) with the goal of developing an effective ground-water quality monitoring network. Initial site reconnaissance work has begun and we report the results, to date, of our geologic hydrogeologic studies. All known solid waste disposal locations are underlain by rocks of either the Late Miocene Neroly Formation or the Cierbo Formation, both of which are dominantly sandstones interbedded with shale and claystone. The existence of a regional confined (artesian) aquifer, as well as a regional water-table aquifer is postulated for Site 300. Preliminary analysis has led to an understanding of directions and depths of regional ground-water flow.

  9. Surface radiation survey and soil sampling of the 300-FF-1 operable unit, Hanford Site, southeastern Washington: A case study

    SciTech Connect (OSTI)

    Teel, S.S.; Olsen, K.B.

    1990-10-01

    The methods used for conducting a radiological characterization of the soil surface for the Phase I Remedial Investigation of a Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA) site is presented via a case study. The study site is an operable unit (300-FF-1) located in and adjacent to the 300 Area of the US Department of Energy's Hanford Site in southeastern Washington State. The operable unit contains liquid and solid waste disposal facilities associated with nuclear fuels fabrication. Continuous surface radiation surveying and soil sampling of selected locations were conducted. Contamination was found in several locations within the operable unit including areas near the liquid and solid waste disposal facilities. Instruments used during surveying included portable beta/gamma (P-11) detectors, and the Ultrasonic Ranging and Data System using an NaI (Tl) detector. Laboratory analyses results indicate that above-background radiation levels were primarily due to the presence of uranium. Both types of field instruments used in the study were effective in detecting surface contamination from radionuclides; however, each had specific advantages. Guidelines are presented for the optimum use of these instruments when performing a radiological characterization of the soil surface. 4 refs., 3 figs., 3 tabs.

  10. A Geophysical Characterization & Monitoring Strategy for Determining Hydrologic Processes in the Hyporheic Corridor at the Hanford 300-Area

    SciTech Connect (OSTI)

    Slater, Lee; Day-Lewis, Frederick; Lane, John; Versteeg, Roelof; Ward, Anderson; Binley, Andrew; Johnson, Timothy; Ntarlagiannis, Dimitrios

    2011-08-31

    The primary objective of this research was to advance the prediction of solute transport between the Uranium contaminated Hanford aquifer and the Columbia River at the Hanford 300 Area by improving understanding of how fluctuations in river stage, combined with subsurface heterogeneity, impart spatiotemporal complexity to solute exchange along the Columbia River corridor. Our work explored the use of continuous waterborne electrical imaging (CWEI), in conjunction with fiber-optic distributed temperature sensor (FO-DTS) and time-lapse resistivity monitoring, to improve the conceptual model for how groundwater/surface water exchange regulates uranium transport. We also investigated how resistivity and induced polarization can be used to generate spatially rich estimates of the variation in depth to the Hanford-Ringold (H-R) contact between the river and the 300 Area Integrated Field Research Challenge (IFRC) site. Inversion of the CWEI datasets (a data rich survey containing {approx}60,000 measurements) provided predictions of the distributions of electrical resistivity and polarizability, from which the spatial complexity of the primary hydrogeologic units along the river corridor was reconstructed. Variation in the depth to the interface between the overlying coarse-grained, high permeability Hanford Formation and the underlying finer-grained, less permeable Ringold Formation, an important contact that limits vertical migration of contaminants, has been resolved along {approx}3 km of the river corridor centered on the IFRC site in the Hanford 300 Area. Spatial variability in the thickness of the Hanford Formation captured in the CWEI datasets indicates that previous studies based on borehole projections and drive-point and multi-level sampling likely overestimate the contributing area for uranium exchange within the Columbia River at the Hanford 300 Area. Resistivity and induced polarization imaging between the river and the 300 Area IFRC further imaged spatial variability in the depth to the Hanford-Ringold inland over a critical region where borehole information is absent, identifying evidence for a continuous depression in the H-R contact between the IFRC and the river corridor. Strong natural contrasts in temperature and specific conductance of river water compared to groundwater at this site, along with periodic river stage fluctuations driven by dam operations, were exploited to yield new insights into the dynamics of groundwater-surface water interaction. Whereas FO-DTS datasets have provided meter-scale measurements of focused groundwater discharge at the riverbed along the corridor, continuous resistivity monitoring has non-invasively imaged spatiotemporal variation in the resistivity inland driven by river stage fluctuations. Time series and time-frequency analysis of FO-DTS and 3D resistivity datasets has provided insights into the role of forcing variables, primarily daily dam operations, in regulating the occurrence of focused exchange at the riverbed and its extension inland. High amplitudes in the DTS and 3D resistivity signals for long periods that dominate the stage time series identify regions along the corridor where stage-driven exchange is preferentially focused. Our work has demonstrated how time-series analysis of both time-lapse resistivity and DTS datasets, in conjunction with resistivity/IP imaging of lithology, can improve understanding of groundwater-surface water exchange along river corridors, offering unique opportunities to connect stage-driven groundwater discharge observed with DTS on the riverbed to stage-driven groundwater and solute fluctuations captured with resistivity inland.

  11. Workplace Charging Equipment and Installation Costs | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Equipment and Installation Costs Workplace Charging Equipment and Installation Costs The costs for a workplace charging program include the costs for charging equipment, installation, maintenance, and supplying electricity. Charging equipment costs depend on the type of charging station you decide to install in your workplace. Level 1 ($300-$1,500) and Level 2 ($400-$6,500) charging stations are commonly installed at workplaces. Explore how charging station equipment features affect the total

  12. Repeated compressive stress increase with 400 [degree]C thermal cycling in tantalum thin films due to increases in the oxygen content

    SciTech Connect (OSTI)

    Cabral, C. Jr.; Clevenger, L.A.; Schad, R.G. )

    1994-07-01

    Stresses which build up in thin films such as tantalum, during thermal processing, can cause major reliability problems in electronic and x-ray optics applications. We demonstrate that 50--200 nm thick sputtered [beta]-Ta thin films undergo repeated compressive stress increases when thermally cycled to 400 [degree]C (at a rate of 10 [degree]C/min) and back in a purified He ambient because of small amounts of oxygen gettered by the tantalum. The oxygen contamination results from the poor quality of the atmospheric seal on the quartz annealing chamber. As-deposited Ta thin films have a compressive stress ranging from [minus]1 to [minus]4 GPa. The compressive stress buildup was monitored [ital in] [ital situ] and was shown to increase [minus]0.5 GPa on average after each thermal cycle for a final value from [minus]6 to [minus]7 GPa after seven cycles. After being cycled thermally seven times any perturbation of the film such as a four-point probe resistivity measurement can cause the film to instantaneously crack in a serpentine pattern, relieving the large compressive stress. Auger electron spectroscopy depth profiling analysis was used to determine that the as-deposited film contained 1 at. % oxygen which increased to 8%--12% after seven thermal cycles with an approximate doubling in resistivity. The [minus]0.5 GPa average compressive stress increase in Ta thin films when cycled to 400 [degree]C is attributed to a 1.3% increase in oxygen concentration leading to a Ta unit cell expansion of 0.6%.

  13. High-Pressure Raman Spectroscopy and X-ray Diffraction Studies of a Terpolymer of Tetrafluoroethylene-Hexafluoropropylene-Vinylidene Fluoride: THV 500

    SciTech Connect (OSTI)

    Emmons, E.D.; Velisavljevic, N.; Schoonover, J.R.; Dattelbaum, D.M.

    2008-04-02

    High-pressure Raman spectroscopy and X-ray diffraction of THV 500, a terpolymer of tetrafluoroethylene-hexafluoropropylene-vinylidene fluoride, were performed using diamond anvil cells (DAC). Changes in the interatomic spacing as well as shifts of several of the vibrational bands as a function of pressure were measured up to {approx}10 GPa. The changes in interatomic spacing and shifts of the vibrational bands are compared to those of polytetrafluoroethylene, showing the effects of copolymerization and reduced crystallinity. The high-pressure behavior of polymers is a relatively unexplored field but is becoming increasingly important due to applications where polymers experience extreme conditions.

  14. Study of Polarized Sea Quark Distributions in Polarized Proton-Proton Collisions at sq root(s) = 500 GeV with PHENIX

    SciTech Connect (OSTI)

    Mibe, Tsutomu

    2009-08-04

    The PHENIX spin program studies the flavor structure of the polarized sea quark distributions in polarized proton-proton collisions. Starting from 2009 run, the quark and antiquark polarization, sorted by flavor, will be investigated with the parity-violating single-spin asymmetry of W-boson production at the collision energy of sq root(s) = 500 GeV. High momentum muons from W-boson decay are detected in the PHENIX muon arms. The muon trigger is being upgraded to allow one to select high momentum muons.

  15. Development of NS-TACSR with extremely suppressed aeolian noise and its application to 500 kV overhead transmission lines

    SciTech Connect (OSTI)

    Tsujimoto, K.; Furukawa, S. (Kansai Electric Power Co., Inc., Osaka (Japan)); Shimojima, K.; Yamamoto, K. (Hitachi Cable, Ltd., Hitachi (JP))

    1991-10-01

    Recently in Japan, with the unprecedented advance of residential area development in the suburbs of large cities, it has become quite difficult to secure the routes of EHV transmission lines from nuclear power plants in remote places to the suburbs of large cities, urging resolution of environmental problems related to transmission lines. In Japan, aerodynamic sound produced by conductors and insulators frequently caused noise problems. Having an opportunity of constructing a 500 kV transmission line through a residential are, we made a research to resolve this noise problem. This paper describes the characteristics of aeolian noise and preventive measures against it.

  16. ALSNews Vol. 300

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    ... This result both provides valuable insight into the motion of magnetic-domain walls and opens a path to further technological developments in spintronics applications. Read more... ...

  17. ALSNews Vol. 300

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    unsubscribe, email This e-mail address is being protected from spambots. You need JavaScript enabled to view it . Towards Heavy Fermions in Europium Intermetallic Compounds This...

  18. ALSNews Vol. 300

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    a broad spectrum of other issues, including detectors; x-ray diffraction; graphene; influenza; nanomagnetism; next generation light sources; numerical modeling; quantum systems,...

  19. HEDL FACILITIES CATALOG 400 AREA

    SciTech Connect (OSTI)

    MAYANCSIK BA

    1987-03-01

    The purpose of this project is to provide a sodium-cooled fast flux test reactor designed specifically for irradiation testing of fuels and materials and for long-term testing and evaluation of plant components and systems for the Liquid Metal Reactor (LMR) Program. The FFTF includes the reactor, heat removal equipment and structures, containment, core component handling and examination, instrumentation and control, and utilities and other essential services. The complex array of buildings and equipment are arranged around the Reactor Containment Building.

  20. 500 MW X-Band RF System of a 0.25 GeV Electron LINAC for Advanced Compton Scattering Source Application

    SciTech Connect (OSTI)

    Chu, Tak Sum; Anderson, Scott; Barty, Christopher; Gibson, David; Hartemann, Fred; Marsh, Roark; Siders, Craig; Adolphsen, Chris; Jongewaard, Erik; Raubenheimer, Tor; Tantawi, Sami; Vlieks, Arnold; Wang, Juwen; /SLAC

    2012-07-03

    A Mono-Energetic Gamma-Ray (MEGa-Ray) Compton scattering light source is being developed at LLNL in collaboration with the SLAC National Accelerator Laboratory. The electron beam for the Compton scattering interaction will be generated by a X-band RF gun and a X-band LINAC at the frequency of 11.424 GHz. High power RF in excess of 500 MW is needed to accelerate the electrons to energy of 250 MeV or greater for the interaction. Two high power klystron amplifiers, each capable of generating 50 MW, 1.5 msec pulses, will be the main high power RF sources for the system. These klystrons will be powered by state of the art solid-state high voltage modulators. A RF pulse compressor, similar to the SLED II pulse compressor, will compress the klystron output pulse with a power gain factor of five. For compactness consideration, we are looking at a folded waveguide setup. This will give us 500 MW at output of the compressor. The compressed pulse will then be distributed to the RF gun and to six traveling wave accelerator sections. Phase and amplitude control are located at the RF gun input and additional control points along the LINAC to allow for parameter control during operation. This high power RF system is being designed and constructed. In this paper, we will present the design, layout, and status of this RF system.

  1. 500 MW X-BAND RF SYSTEM OF A 0.25 GEV ELECTRON LINAC FOR ADVANCED COMPTON SCATTERING SOURCE APPLICATION

    SciTech Connect (OSTI)

    Chu, T S; Anderson, S G; Gibson, D J; Hartemann, F V; Marsh, R A; Siders, C; Barty, C P; Adolphsen, C; Jongewaard, E; Tantawi, S; Vlieks, A; Wang, J W; Raubenheimer, T

    2010-05-12

    A Mono-Energetic Gamma-Ray (MEGa-Ray) Compton scattering light source is being developed at LLNL in collaboration with SLAC National Accelerator Laboratory. The electron beam for the Compton scattering interaction will be generated by a X-band RF gun and a X-band LINAC at the frequency of 11.424 GHz. High power RF in excess of 500 MW is needed to accelerate the electrons to energy of 250 MeV or greater for the interaction. Two high power klystron amplifiers, each capable of generating 50 MW, 1.5 msec pulses, will be the main high power RF sources for the system. These klystrons will be powered by state of the art solid-state high voltage modulators. A RF pulse compressor, similar to the SLED II pulse compressor, will compress the klystron output pulse with a power gain factor of five. For compactness consideration, we are looking at a folded waveguide setup. This will give us 500 MW at output of the compressor. The compressed pulse will then be distributed to the RF gun and to six traveling wave accelerator sections. Phase and amplitude control are located at the RF gun input and additional control points along the LINAC to allow for parameter control during operation. This high power RF system is being designed and constructed. In this paper, we will present the design, layout, and status of this RF system.

  2. Application of Maximum Likelihood Bayesian Model Averaging to Groundwater Flow and Transport at the Hanford Site 300 Area

    SciTech Connect (OSTI)

    Meyer, Philip D.; Ye, Ming; Neuman, Shlomo P.; Rockhold, Mark L.

    2008-06-01

    A methodology to systematically and quantitatively assess model predictive uncertainty was applied to saturated zone uranium transport at the 300 Area of the U.S. Department of Energy Hanford Site in Washington State, USA. The methodology extends Maximum Likelihood Bayesian Model Averaging (MLBMA) to account jointly for uncertainties due to the conceptual-mathematical basis of models, model parameters, and the scenarios to which the models are applied. Conceptual uncertainty was represented by postulating four alternative models of hydrogeology and uranium adsorption. Parameter uncertainties were represented by estimation covariances resulting from the joint calibration of each model to observed heads and uranium concentration. Posterior model probability was dominated by one model. Results demonstrated the role of model complexity and fidelity to observed system behavior in determining model probabilities, as well as the impact of prior information. Two scenarios representing alternative future behavior of the Columbia River adjacent to the site were considered. Predictive simulations carried out with the calibrated models illustrated the computation of model- and scenario-averaged predictions and how results can be displayed to clearly indicate the individual contributions to predictive uncertainty of the model, parameter, and scenario uncertainties. The application demonstrated the practicability of applying a comprehensive uncertainty assessment to large-scale, detailed groundwater flow and transport modelling.

  3. Environmental Controls on the Activity of Aquifer Microbial Communities in the 300 Area of the Hanford Site

    SciTech Connect (OSTI)

    Konopka, Allan; Plymale, Andrew E.; Carvajal, Denny A.; Lin, Xueju; McKinley, James P.

    2013-11-06

    Aquifer microbes in the 300 Area of the Hanford Site in southeastern Washington State, USA are periodically exposed to U(VI) concentrations that can range up to 10 ?M in small sediment fractures. Assays of 35 H-leucine incorporation indicated that both sediment-associated and planktonic microbes were metabolically active, and that organic C was growth-limiting in the sediments. Although bacteria suspended in native groundwater retained high activity when exposed to 100 ?M U(VI), they were inhibited by U(VI) < 1 ?M in synthetic groundwater that lacked added bicarbonate. Chemical speciation modeling suggested that positively-charged species and particularly (UO2)3(OH)5+ rose in concentration as more U(VI) was added to synthetic groundwater, but that carbonate complexes dominated U(VI) speciation in natural groundwater. U toxicity was relieved when increasing amounts of bicarbonate were added to synthetic groundwater containing 4.5 ?M U(VI). Pertechnetate, an oxyanion that is another contaminant of concern at the Hanford Site, was not toxic to groundwater microbes at concentrations up to 125 ?M.

  4. Current flow and efficiencies of concentrator InGaP/GaAs/Ge solar cells at temperatures below 300K

    SciTech Connect (OSTI)

    Kalinovsky, Vitaly S. Kontrosh, Evgeny V. Dmitriev, Pavel A. Pokrovsky, Pavel V. Chekalin, Alexander V. Andreev, Viacheslav M.

    2014-09-26

    The forward dark current density voltage (J-V) characteristic is one of the most important characteristics of multi-junction solar cells. It indicates that the mechanisms of current flow in the space charge region of photoactive p-n junctions. If one is to idealize the optical and electrical (coupling) elements of the solar cells, it is the J-V characteristic that determines the theoretically possible efficiency of the solar cell. In this paper, using the connection between the dark J-V and photovoltaic (?-J{sub g}) efficiency generated current density characteristics, the effect of current transport mechanisms in the space charge on the efficiency of multi-junction solar cells was investigated in the temperature range of 300 80 K. In the experimental J-V and ?-J{sub g} curves of the multi-junction solar cells, segments corresponding to the dominant current transport mechanisms were identified. The developed method, based on the analysis of forward dark J-V characteristics, makes it possible to identify the parameters affecting the efficiency of the multi-junction solar cells in a wide range of temperatures and solar radiation concentration.

  5. Raman spectral studies of aqueous zinc bromide solutions to 300/sup 0/C at pressures of 9 MPa

    SciTech Connect (OSTI)

    Yang, M.M.; Crerar, D.A.; Irish, D.E.

    1988-08-01

    A Raman spectral study of 14 solutions of varying bromide to zinc ratios was conducted up to 300/sup 0/C and 9 MPa. The tetra-, tri-, di- as well as the mono-bromozinc complexes were identified. The signal from the ZnBr/sup +/ complex increased in intensity as temperature increased, for solutions of low bromide- to-zinc ratios. The ZnBr/sub 4//sup 2 -/ species was favored at higher Br/Zn ratios, and higher temperatures favored the formation of the species ZnBr/sub 2/ and ZnBr/sup +/ at the expense of ZnBr/sub 4//sup 2 -/ and ZnBr/sub 3//sup -/. Although solvated water is probably present in these zinc-bromo complexes, they found no evidence of O-Zn vibrations other than for Zn(H/sub 2/O)/sub 6//sup 2 +/. However, spectra of successive dilutions of solutions with high bromide to zinc ratios show a relative change in species populations thereby suggesting that water activity plays a decisive role in complex formation. For the first time trifluoromethanesulfonic acid (HTFMS) has been used as an internal standard in Raman spectroscopy. This permitted quantitative measurement of stepwise stability constants.

  6. BLAST: CORRELATIONS IN THE COSMIC FAR-INFRARED BACKGROUND AT 250, 350, AND 500 mum REVEAL CLUSTERING OF STAR-FORMING GALAXIES

    SciTech Connect (OSTI)

    Viero, Marco P.; Martin, Peter G.; Netterfield, Calvin B.; Ade, Peter A. R.; Griffin, Matthew; Hargrave, Peter C.; Mauskopf, Philip; Moncelsi, Lorenzo; Pascale, Enzo; Bock, James J.; Chapin, Edward L.; Halpern, Mark; Marsden, Gaelen; Devlin, Mark J.; Klein, Jeff; Gundersen, Joshua O.; Hughes, David H.; MacTavish, Carrie J.; Negrello, Mattia; Olmi, Luca

    2009-12-20

    We detect correlations in the cosmic far-infrared background due to the clustering of star-forming galaxies in observations made with the Balloon-borne Large Aperture Submillimeter Telescope, at 250, 350, and 500 mum. We perform jackknife and other tests to confirm the reality of the signal. The measured correlations are well fitted by a power law over scales of 5'-25', with DELTAI/I = 15.1% +- 1.7%. We adopt a specific model for submillimeter sources in which the contribution to clustering comes from sources in the redshift ranges 1.3 <= z <= 2.2, 1.5 <= z <= 2.7, and 1.7 <= z <= 3.2, at 250, 350, and 500 mum, respectively. With these distributions, our measurement of the power spectrum, P(k{sub t}heta), corresponds to linear bias parameters, b = 3.8 +- 0.6, 3.9 +- 0.6, and 4.4 +- 0.7, respectively. We further interpret the results in terms of the halo model, and find that at the smaller scales, the simplest halo model fails to fit our results. One way to improve the fit is to increase the radius at which dark matter halos are artificially truncated in the model, which is equivalent to having some star-forming galaxies at z >= 1 located in the outskirts of groups and clusters. In the context of this model, we find a minimum halo mass required to host a galaxy is log(M{sub min}/M{sub sun}) = 11.5{sup +0.4}{sub -0.1}, and we derive effective biases b{sub eff} = 2.2 +- 0.2, 2.4 +- 0.2, and 2.6 +- 0.2, and effective masses log(M{sub eff}/M{sub odot})=12.9+-0.3, 12.8 +- 0.2, and 12.7 +- 0.2, at 250, 350 and 500 mum, corresponding to spatial correlation lengths of r{sub 0} = 4.9, 5.0, and 5.2+-0.7 h{sup -1}Mpc, respectively. Finally, we discuss implications for clustering measurement strategies with Herschel and Planck.

  7. K500 - Facilities - Cyclotron Institute

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    The 50-kilogauss magnetic field is generated by 800 Amperes of electrical current carried by 5500 turns (25 miles) of niobium-titanium superconducting wire in a coil surrounded by ...

  8. Powered by 500 Trillion Calculations

    Broader source: Energy.gov [DOE]

    Argonne's supercomputer is using its superpowers to map the movement of red blood cells -- which will hopefully lead to better diagnoses and treatments for patients with blood flow complications.

  9. Proposed amendment to presidential permit PP-63 and associated modifications to 500 kV international transmission line, Forbes, Minnesota to Manitoba, Canada. [Forbes Substation

    SciTech Connect (OSTI)

    Not Available

    1992-10-01

    This Addendum to the Final Environmental Assessment for the Proposed Amendment to Presidential Permit PP-63 and Associated Modifications to 500 kV International Transmission Line: Forbes, Minnesota to Manitoba, Canada (DOE/EA-587) addresses Northern States Power Company's (NSP) proposed expansion of the Forbes Substation. The applicant has requested that the expansion take place on the west side of the substation, within the existing property line, instead of on the north side as originally proposed. All of the proposed construction would take place on property already owned by NSP. DOE has reviewed the environmental impacts associated with this minor modification and has determined that the conclusions reached in the environmental assessment and Finding of No Significant Impact prepared in connection with NSP's original amendment request remain valid.

  10. {sup 147}Sm(n,{alpha}) cross section measurements from 3 eV to 500 keV: Implications for explosive nucleosynthesis reaction rates

    SciTech Connect (OSTI)

    Gledenov, Yu. M.; Koehler, P. E.; Andrzejewski, J.; Guber, K. H.; Rauscher, T.

    2000-10-01

    We have measured the {sup 147}Sm(n,{alpha}) cross section from 3 eV to 500 keV. These data were used to test nuclear statistical models which must be relied on to calculate the rates for as yet unmeasurable reactions occurring in explosive nucleosynthesis scenarios. It was found that our data are in reasonably good agreement with the reaction rate predicted by an older model but that the rates predicted by two very recent models are roughly a factor of 3 different from the data (in opposite directions). A detailed analysis indicates the strong dependence on the employed optical {alpha} potentials. These results, together with counting rate estimates for future experiments indicate that (n,{alpha}) measurements will be useful for improving reaction rate predictions across the global range of masses needed for explosive nucleosynthesis calculations.

  11. Measurement of the parity-violating longitudinal single-spin asymmetry for W+- boson production in polarized proton-proton collisions at sqrt s = 500 GeV

    SciTech Connect (OSTI)

    Aggarwal, M.M.; Dunlop, J.; et al.

    2011-02-11

    We report the first measurement of the parity-violating single-spin asymmetries for midrapidity decay positrons and electrons from W{sup +} and W{sup -} boson production in longitudinally polarized proton-proton collisions at {radical}s = 500 GeV by the STAR experiment at RHIC. The measured asymmetries, A{sub L}{sup W+} = -0.27 {+-} 0.10(stat.) {+-} 0.02(syst.) {+-} 0.03(norm.) and A{sub L}{sup W-} = 0.14 {+-} 0.19(stat.) {+-} 0.02(syst.) {+-} 0.01(norm.), are consistent with theory predictions, which are large and of opposite sign. These predictions are based on polarized quark and antiquark distribution functions constrained by polarized deep-inelastic scattering measurements.

  12. Propagation and stability characteristics of a 500-m-long laser-based fiducial line for high-precision alignment of long-distance linear accelerators

    SciTech Connect (OSTI)

    Suwada, Tsuyoshi; Satoh, Masanori; Telada, Souichi; Minoshima, Kaoru

    2013-09-15

    A laser-based alignment system with a He-Ne laser has been newly developed in order to precisely align accelerator units at the KEKB injector linac. The laser beam was first implemented as a 500-m-long fiducial straight line for alignment measurements. We experimentally investigated the propagation and stability characteristics of the laser beam passing through laser pipes in vacuum. The pointing stability at the last fiducial point was successfully obtained with the transverse displacements of ±40 μm level in one standard deviation by applying a feedback control. This pointing stability corresponds to an angle of ±0.08 μrad. This report contains a detailed description of the experimental investigation for the propagation and stability characteristics of the laser beam in the laser-based alignment system for long-distance linear accelerators.

  13. Cone beam breast CT with a high pitch (75 μm), thick (500 μm) scintillator CMOS flat panel detector: Visibility of simulated microcalcifications

    SciTech Connect (OSTI)

    Shen, Youtao; Zhong, Yuncheng; Lai, Chao-Jen; Wang, Tianpeng; Shaw, Chris C.

    2013-10-15

    Purpose: To measure and investigate the improvement of microcalcification (MC) visibility in cone beam breast CT with a high pitch (75 μm), thick (500 μm) scintillator CMOS/CsI flat panel detector (Dexela 2923, Perkin Elmer).Methods: Aluminum wires and calcium carbonate grains of various sizes were embedded in a paraffin cylinder to simulate imaging of calcifications in a breast. Phantoms were imaged with a benchtop experimental cone beam CT system at various exposure levels. In addition to the Dexela detector, a high pitch (50 μm), thin (150 μm) scintillator CMOS/CsI flat panel detector (C7921CA-09, Hamamatsu Corporation, Hamamatsu City, Japan) and a widely used low pitch (194 μm), thick (600 μm) scintillator aSi/CsI flat panel detector (PaxScan 4030CB, Varian Medical Systems) were also used in scanning for comparison. The images were independently reviewed by six readers (imaging physicists). The MC visibility was quantified as the fraction of visible MCs and measured as a function of the estimated mean glandular dose (MGD) level for various MC sizes and detectors. The modulation transfer functions (MTFs) and detective quantum efficiencies (DQEs) were also measured and compared for the three detectors used.Results: The authors have demonstrated that the use of a high pitch (75 μm) CMOS detector coupled with a thick (500 μm) CsI scintillator helped make the smaller 150–160, 160–180, and 180–200 μm MC groups more visible at MGDs up to 10.8, 9, and 10.8 mGy, respectively. It also made the larger 200–212 and 212–224 μm MC groups more visible at MGDs up to 7.2 mGy. No performance improvement was observed for 224–250 μm or larger size groups. With the higher spatial resolution of the Dexela detector based system, the apparent dimensions and shapes of MCs were more accurately rendered. The results show that with the aforementioned detector, a 73% visibility could be achieved in imaging 160–180 μm MCs as compared to 28% visibility achieved by the low pitch (194 μm) aSi/CsI flat panel detector. The measurements confirm that the Hamamatsu detector has the highest MTF, followed by the Dexel detector, and then the Varian detector. However, the Dexela detector, with its thick (500 μm) CsI scintillator and low noise level, has the highest DQE at all frequencies, followed by the Varian detector, and then the Hamamatsu detector. The findings on the MC visibility correlated well with the differences in MTFs, noise power spectra, and DQEs measured for these three detectors.Conclusions: The authors have demonstrated that the use of the CMOS type Dexela detector with its high pitch (75 μm) and thick (500 μm) CsI scintillator could help improve the MC visibility. However, the improvement depended on the exposure level and the MC size. For imaging larger MCs or scanning at high exposure levels, there was little advantage in using the Dexela detector as compared to the aSi type Varian detector. These findings correlate well with the higher measured DQEs of the Dexela detector, especially at higher frequencies.

  14. Generation and use of high power 213 nm and 266 nm laser radiation and tunable 210-400 nm laser radiation with BBO crystal matrix array

    DOE Patents [OSTI]

    Gruen, Dieter M.

    2000-01-01

    A 213 nm laser beam is capable of single photon ablative photodecomposition for the removal of a polymer or biological material substrate. Breaking the molecular bonds and displacing the molecules away from the substrate in a very short time period results in most of the laser photon energy being carried away by the displaced molecules, thus minimizing thermal damage to the substrate. The incident laser beam may be unfocussed and is preferably produced by quintupling the 1064 nm radiation from a Nd:YAG solid state laser, i.e., at 213 nm. In one application, the 213 nm laser beam is expanded in cross section and directed through a plurality of small beta barium borate (BBO) crystals for increasing the energy per photon of the laser radiation directed onto the substrate. The BBO crystals are arranged in a crystal matrix array to provide a large laser beam transmission area capable of accommodating high energy laser radiation without damaging the BBO crystals. The BBO crystal matrix array may also be used with 266 nm laser radiation for carrying out single or multi photon ablative photodecomposition. The BBO crystal matrix array may also be used in an optical parametric oscillator mode to generate high power tunable laser radiation in the range of 210-400 nm.

  15. Adiabatic release measurements in aluminum between 400-1200 GPa. Characterization of aluminum as a shock standard in the multimegabar regime

    SciTech Connect (OSTI)

    Knudson, Marcus D.; Desjarlais, Michael P.; Pribram-Jones, Aurora

    2015-06-15

    Aluminum has been used prolifically as an impedance matching standard in the multimegabar regime (1 Mbar = 100 GPa), particularly in nuclear driven, early laser driven, and early magnetically driven flyer plate experiments. The accuracy of these impedance matching measurements depends upon the knowledge of both the Hugoniot and release or reshock response of aluminum. Here, we present the results of several adiabatic release measurements of aluminum from ~4001200 GPa states along the principal Hugoniot using full density polymethylpentene (commonly known as TPX), and both ~190 and ~110 mg/cc silica aerogel standards. Additionally, these data were analyzed within the framework of a simple, analytical model that was motivated by a first-principles molecular dynamics investigation into the release response of aluminum, as well as by a survey of the release response determined from several tabular equations of state for aluminum. Combined, this theoretical and experimental study provides a method to perform impedance matching calculations without the need to appeal to any tabular equation of state for aluminum. Furthermore, as an analytical model, this method allows for propagation of all uncertainty, including the random measurement uncertainties and the systematic uncertainties of the Hugoniot and release response of aluminum. This work establishes aluminum for use as a high-precision standard for impedance matching in the multimegabar regime.

  16. Adiabatic release measurements in aluminum between 400-1200 GPa. Characterization of aluminum as a shock standard in the multimegabar regime

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Knudson, Marcus D.; Desjarlais, Michael P.; Pribram-Jones, Aurora

    2015-06-15

    Aluminum has been used prolifically as an impedance matching standard in the multimegabar regime (1 Mbar = 100 GPa), particularly in nuclear driven, early laser driven, and early magnetically driven flyer plate experiments. The accuracy of these impedance matching measurements depends upon the knowledge of both the Hugoniot and release or reshock response of aluminum. Here, we present the results of several adiabatic release measurements of aluminum from ~400–1200 GPa states along the principal Hugoniot using full density polymethylpentene (commonly known as TPX), and both ~190 and ~110 mg/cc silica aerogel standards. Additionally, these data were analyzed within the frameworkmore » of a simple, analytical model that was motivated by a first-principles molecular dynamics investigation into the release response of aluminum, as well as by a survey of the release response determined from several tabular equations of state for aluminum. Combined, this theoretical and experimental study provides a method to perform impedance matching calculations without the need to appeal to any tabular equation of state for aluminum. Furthermore, as an analytical model, this method allows for propagation of all uncertainty, including the random measurement uncertainties and the systematic uncertainties of the Hugoniot and release response of aluminum. This work establishes aluminum for use as a high-precision standard for impedance matching in the multimegabar regime.« less

  17. Improvements in 500-kHz Ultrasonic Phased-Array Probe Designs for Evaluation of Thick Section Cast Austenitic Stainless Steel Piping Welds

    SciTech Connect (OSTI)

    Crawford, Susan L.; Cinson, Anthony D.; Moran, Traci L.; Anderson, Michael T.; Diaz, Aaron A.

    2011-02-01

    PNNL has been studying and performing confirmatory research on the inspection of piping welds in coarse-grained steels for over 30 years. More recent efforts have been the application of low frequency phased array technology to this difficult to inspect material. The evolution of 500 kHz PA probes and the associated electronics and scanning protocol are documented in this report. The basis for the probe comparisons are responses from one mechanical fatigue crack and two thermal fatigue cracks in large-bore cast mockup specimens on loan from the Electric Power Research Institution. One of the most significant improvements was seen in the use of piezo-composite elements in the later two probes instead of the piezo-ceramic material used in the prototype array. This allowed a reduction in system gain of 30 dB and greatly reduced electronic noise. The latest probe had as much as a 5 dB increase in signal to noise, adding to its flaw discrimination capability. The system electronics for the latest probe were fully optimized for a 500 kHz center frequency, however significant improvements were not observed in the center frequency of the flaw responses. With improved scanner capabilities, smaller step sizes were used, allowing both line and raster data improvements to be made with the latest probe. The small step sizes produce high resolution images that improve flaw discrimination and, along with the increased signal-to-noise ratio inherent in the latest probe design, enhanced detection of the upper regions of the flaw make depth sizing more plausible. Finally, the physical sizes of the probes were progressively decreased allowing better access to the area of interest on specimens with weld crowns, and the latest probe was designed with non-integral wedges providing flexibility in focusing on different specimen geometries.

  18. Ultrasound-Guided Radiological Placement of Central Venous Port via the Subclavian Vein: A Retrospective Analysis of 500 Cases at a Single Institute

    SciTech Connect (OSTI)

    Sakamoto, Noriaki Arai, Yasuaki Takeuchi, Yoshito Takahashi, Masahide Tsurusaki, Masakatsu; Sugimura, Kazuro

    2010-10-15

    The purpose of this study was to assess the technical success rate and adverse events (AEs) associated with ultrasound (US)-guided radiological placement (RP) of a central venous port (CVP) via the subclavian vein (SCV). Between April 2006 and May 2007, a total of 500 US-guided RPs of a CVP via the SCV were scheduled in 486 cancer patients (mean age {+-} SD, 54.1 {+-} 18.1 years) at our institute. Referring to the interventional radiology report database and patients' records, technical success rate and AEs relevant to CVP placement were evaluated retrospectively. The technical success rate was 98.6% (493/500). AEs occurred in 26 cases (5.2%) during follow-up (range, 1-1080 days; mean {+-} SD, 304.0 {+-} 292.1 days). AEs within 24 h postprocedure occurred in five patients: pneumothorax (n = 2), arterial puncture (n = 1), hematoma formation at the pocket site (n = 2), and catheter tip migration into the internal mammary vein (n = 1). There were seven early AEs: hematoma formation at the pocket site (n = 2), fibrin sheath formation around the indwelling catheter (n = 2), and catheter-related infections (n = 3). There were 13 delayed AEs: catheter-related infections (n = 7), catheter detachments (n = 3), catheter occlusion (n = 1), symptomatic thrombus in the SCV (n = 1), and catheter migration (n = 1). No major AEs, such as procedure-related death, air embolism, or events requiring surgical intervention, were observed. In conclusion, US-guided RP of a CVP via the SCV is highly appropriate, based on its high technical success rate and the limited number of AEs.

  19. Conversion of CH4 into H2 at 300 C using Pd/MnO2 catalyst made with an effect of water oxidation

    SciTech Connect (OSTI)

    Koyanaka, Hideki; Takeuchi, K; Kolesnikov, Alexander I

    2014-01-01

    A novel electricity-free deposition of palladium on the surface of manganese dioxide, which has a crystal structure of ramsdellite, was studied. Using the Pd deposition, a nano-particle of Pd/MnO2 was prepared, and it was used for a catalytic performance for reforming methane into hydrogen at 300 C.

  20. THE 300 km s{sup -1} STELLAR STREAM NEAR SEGUE 1: INSIGHTS FROM HIGH-RESOLUTION SPECTROSCOPY OF ITS BRIGHTEST STAR

    SciTech Connect (OSTI)

    Frebel, Anna; Casey, Andrew R.; Lunnan, Ragnhild; Norris, John E.; Wyse, Rosemary F. G.; Gilmore, Gerard

    2013-07-01

    We present a chemical abundance analysis of 300S-1, the brightest likely member star of the 300 km s{sup -1} stream near the faint satellite galaxy Segue 1. From a high-resolution Magellan/MIKE spectrum, we determine a metallicity of [Fe/H] = -1.46 {+-} 0.05 {+-} 0.23 (random and systematic uncertainties) for star 300S-1, and find an abundance pattern similar to typical halo stars at this metallicity. Comparing our stellar parameters to theoretical isochrones, we estimate a distance of 18 {+-} 7 kpc. Both the metallicity and distance estimates are in good agreement with what can be inferred from comparing the Sloan Digital Sky Survey photometric data of the stream stars to globular cluster sequences. While several other structures overlap with the stream in this part of the sky, the combination of kinematic, chemical, and distance information makes it unlikely that these stars are associated with either the Segue 1 galaxy, the Sagittarius Stream, or the Orphan Stream. Streams with halo-like abundance signatures, such as the 300 km s{sup -1} stream, present another observational piece for understanding the accretion history of the Galactic halo.

  1. Measurement of transmission efficiency for 400 MeV proton beam through collimator at Fermilab MuCool Test Area using Chromox-6 scintillation screen

    SciTech Connect (OSTI)

    Jana, M. R.; Chung, M.; Leonova, M.; Moretti, A.; Palmer, M.; Schwarz, T.; Tollestrup, A.; Yonehara, K.; Freemire, B.; Hanlet, P.; Torun, Y.

    2013-06-15

    The MuCool Test Area (MTA) at Fermilab is a facility to develop the technology required for ionization cooling for a future Muon Collider and/or Neutrino Factory. As part of this research program, feasibility studies of various types of RF cavities in a high magnetic field environment are in progress. As a unique approach, we have tested a RF cavity filled with a high pressure hydrogen gas with a 400 MeV proton beam in an external magnetic field (B = 3 T). Quantitative information about the number of protons passing through this cavity is an essential requirement of the beam test. The MTA is a flammable gas (hydrogen) hazard zone. Due to safety reasons, no active (energized) beam diagnostic instrument can be used. Moreover, when the magnetic field is on, current transformers (toroids) used for beam intensity measurements do not work due to the saturation of the ferrite material of the transformer. Based on these requirements, we have developed a passive beam diagnostic instrumentation using a combination of a Chromox-6 scintillation screen and CCD camera. This paper describes details of the beam profile and position obtained from the CCD image with B = 0 T and B = 3 T, and for high and low intensity proton beams. A comparison is made with beam size obtained from multi-wires detector. Beam transmission efficiency through a collimator with a 4 mm diameter hole is measured by the toroids and CCD image of the scintillation screen. Results show that the transmission efficiency estimated from the CCD image is consistent with the toroid measurement, which enables us to monitor the beam transmission efficiency even in a high magnetic field environment.

  2. Irradiation creep and density changes observed in MA957 pressurized tubes irradiated to doses of 40-110 dpa at 400-750°C in FFTF

    SciTech Connect (OSTI)

    Toloczko, Mychailo B.; Garner, Frank A.; Maloy, Stuart A.

    2012-12-30

    An irradiation creep and swelling study was performed on tubing constructed from the Y2O3-strengthened ODS ferritic steel MA957. As a result of the reduction operations during manufacture, the grains in the tubing were highly elongated in the direction of the tubing axis, with an aspect ratio of ~10:1. Pressurized creep tubes were irradiated in the Fast Flux Test Facility (FFTF) to doses ranging from 40 dpa to 110 dpa at temperatures ranging from 400 to 750°C. The diametral strains produced during irradiation exhibit very strong transient strains that are linearly dependent on stress and increase with irradiation temperature before reaching temperature-independent steady-state creep rates of 0.6-0.7 X 10-6 (MPa dpa)-1. Contributions to transient strains may not arise only from classical thermal creep or irradiation creep considerations, but also may result from an irradiation-stimulated growth process whereby the highly elongated grain structure reduces the aspect ratio to produce fatter grains and thereby increases in the tube diameter. One manifestation of this process is a change in tube diameter that is not accompanied by a density change characteristic of void swelling or precipitation-induced changes in lattice parameter. These results provide the first conclusive demonstration that resistance to irradiation creep can be extended to higher temperatures by dispersoid addition, and most importantly, this resistance is maintained to high radiation damage levels. However, the irradiation creep compliance is not reduced by dispersoid addition, casting some doubt on various proposed climb and glide mechanisms of irradiation creep.

  3. Impact Mitigation and Monitoring of the BPA 500-kV Garrison-Taft Transmission Line : Effects on Elk Security and Hunter Opportunity, Final Report.

    SciTech Connect (OSTI)

    Canfield, Jodie E.

    1988-11-01

    This study was conducted by the Montana Department of Fish, Wildlife and Parks from 1984--1988 to assess the impacts of the Garrison-Taft segment of a 500-kV powerline on elk summer-fall habitat. Construction of the powerline began in 1983, and the powerline was energized in 1985. The Garrison-Taft powerline corridor crossed 251 km of mountainous terrain in western Montana; about 465 km of new roads were constructed to provide permanent access to the powerline towers. The objectives of the study were: (1) to monitor the effectiveness of mitigation measures, including timing restrictions on construction activities and road closures on newly-built access roads, and (2) to determine if opening previously-unroaded elk security habitats to hunters by powerline access roads affected elk habitat use, distribution, use of security areas, or elk harvest. In addition, both the potential for accelerated timber harvest in areas crossed by the powerline that would not have otherwise been logged because of marginal economics and lack of haul roads and the potential effect of powerline flashovers on future prescribed burning of elk winter-ranges were evaluated. 83 refs., 88 figs., 15 tabs.

  4. Design and development of Stirling engines for stationary power generation applications in the 500 to 3000 horsepower range. Volume 1. Technical report

    SciTech Connect (OSTI)

    Not Available,

    1980-09-15

    This project was Phase I of a multiphased program for the design and development of Stirling engines for stationary power generation applications in the 500 to 3000 horsepower range. Phase I comprised the conceptual design and associated cost estimates of a stationary Stirling engine capable of being fueled by a variety of heat sources, with emphasis on coal firing, followed by the preparation of a plan for implementing the design, fabrication and testing of a demonstration engine by 1985. The development and evaluation of conceptual designs have been separated into two broad categories: the A designs which represent the present state-of-the-art and which are demonstrable by 1985 with minimum technical risk; and the B designs which involve advanced technology and therefore would require significant research and development prior to demonstration and commercialization, but which may ultimately offer advantages in terms of lower cost, better performance, or higher reliability. The majority of the effort in Phase I was devoted to the A designs.

  5. Design and development of Stirling engines for stationary-power-generation applications in the 500- to 3000-horsepower range. Phase I final report

    SciTech Connect (OSTI)

    1980-10-01

    A program plan and schedule for the implementation of the proposed conceptual designs through the remaining four phases of the overall large Stirling engine development program was prepared. The objective of Phase II is to prepare more detailed designs of the conceptual designs prepared in Phase I. At the conclusion of Phase II, a state-of-the-art design will be selected from the candidate designs developed in Phase I for development. The objective of Phase III is to prepare manufacturing drawings of the candidate engine design. Also, detailed manufacturing drawings of both 373 kW (500 hp) and 746 kW (1000 hp) power pack skid systems will be completed. The power pack skid systems will include the generator, supporting skid, controls, and other supporting auxiliary subsystems. The Stirling cycle engine system (combustion system, Stirling engine, and heat transport system) will be mounted in the power pack skid system. The objective of Phase IV is to procure parts for prototype engines and two power pack skid systems and to assemble Engines No. 1 and 2. The objective of Phase V is to perform extensive laboratory and demonstration testing of the Stirling engines and power pack skid systems, to determine the system performance and cost and commercialization strategy. Scheduled over a 6 yr period the cost of phases II through V is estimated at $22,063,000. (LCL)

  6. {sup 7}Li(n,{gamma}){sup 8}Li reaction and the S{sub 17} factor at E{sub c.m.}>500 keV

    SciTech Connect (OSTI)

    Nagai, Y.; Shima, T.; Tomyo, A.; Igashira, M.; Takaoka, T.; Kikuchi, T.; Mengoni, A.; Otsuka, T.

    2005-05-01

    The partial cross sections from the neutron capture state to the ground and first excited states in {sup 8}Li have been separately determined for the first time at stellar neutron energy. The direct and weak cascade {gamma} rays from the capture and first excited states to the ground state were measured by means of anti-Compton NaI(Tl) and anti-Compton HPGe spectrometers, respectively. The {gamma}-ray branching ratio and the cross sections thus determined agree with that for thermal neutrons assuming a 1/v neutron velocity dependence. By comparing the cross sections with calculations based on the nonresonant direct capture mechanism it is shown that the cross sections are sensitive to the interaction potential of the incident neutron with the {sup 7}Li target nucleus. This analysis confirms the possibility of deriving the parameters necessary for the calculation of the astrophysical S factor S{sub 17}(E) for the {sup 7}Be(p,{gamma}){sup 8}B reaction in the upper energy range above 500 keV.

  7. Cross Section and Parity-Violating Spin Asymmetries of W{sup {+-}} Boson Production in Polarized p+p Collisions at {radical}(s)=500 GeV

    SciTech Connect (OSTI)

    Adare, A.; Kinney, E.; Linden Levy, L. A.; Nagle, J. L.; Wysocki, M.; Afanasiev, S.; Isupov, A.; Litvinenko, A.; Malakhov, A.; Peresedov, V.; Rukoyatkin, P.; Zolin, L.; Aidala, C.; Brooks, M. L.; Butsyk, S.; Guo, L.; Jiang, X.; Kapustinsky, J.; Kunde, G. J.; Lee, D. M.

    2011-02-11

    Large parity-violating longitudinal single-spin asymmetries A{sub L}{sup e+}=-0.86{sub -0.14}{sup +0.30} and A{sub L}{sup e-}=0.88{sub -0.71}{sup +0.12} are observed for inclusive high transverse momentum electrons and positrons in polarized p+p collisions at a center-of-mass energy of {radical}(s)=500 GeV with the PHENIX detector at RHIC. These e{sup {+-}} come mainly from the decay of W{sup {+-}} and Z{sup 0} bosons, and their asymmetries directly demonstrate parity violation in the couplings of the W{sup {+-}} to the light quarks. The observed electron and positron yields were used to estimate W{sup {+-}} boson production cross sections for the e{sup {+-}} channels of {sigma}(pp{yields}W{sup +}X)xBR(W{sup +}{yields}e{sup +}{nu}{sub e})=144.1{+-}21.2(stat){sub -10.3}{sup +3.4}(syst){+-}21.6(norm) pb, and {sigma}(pp{yields}W{sup -}X)xBR(W{sup -}{yields}e{sup -}{nu}{sub e})=31.7{+-}12.1(stat){sub -8.2}{sup +10.1}(syst){+-}4.8(norm) pb.

  8. Towards a beyond 1 GHz solid-state nuclear magnetic resonance: External lock operation in an external current mode for a 500 MHz nuclear magnetic resonance

    SciTech Connect (OSTI)

    Takahashi, Masato; Maeda, Hideaki; Ebisawa, Yusuke; Tennmei, Konosuke; Yanagisawa, Yoshinori; Nakagome, Hideki; Hosono, Masami; Takasugi, Kenji; Hase, Takashi; Miyazaki, Takayoshi; Fujito, Teruaki; Kiyoshi, Tsukasa; Yamazaki, Toshio

    2012-10-15

    Achieving a higher magnetic field is important for solid-state nuclear magnetic resonance (NMR). But a conventional low temperature superconducting (LTS) magnet cannot exceed 1 GHz (23.5 T) due to the critical magnetic field. Thus, we started a project to replace the Nb{sub 3}Sn innermost coil of an existing 920 MHz NMR (21.6 T) with a Bi-2223 high temperature superconducting (HTS) innermost coil. Unfortunately, the HTS magnet cannot be operated in persistent current mode; an external dc power supply is required to operate the NMR magnet, causing magnetic field fluctuations. These fluctuations can be stabilized by a field-frequency lock system based on an external NMR detection coil. We demonstrate here such a field-frequency lock system in a 500 MHz LTS NMR magnet operated in an external current mode. The system uses a {sup 7}Li sample in a microcoil as external NMR detection system. The required field compensation is calculated from the frequency of the FID as measured with a frequency counter. The system detects the FID signal, determining the FID frequency, and calculates the required compensation coil current to stabilize the sample magnetic field. The magnetic field was stabilized at 0.05 ppm/3 h for magnetic field fluctuations of around 10 ppm. This method is especially effective for a magnet with large magnetic field fluctuations. The magnetic field of the compensation coil is relatively inhomogeneous in these cases and the inhomogeneity of the compensation coil can be taken into account.

  9. Improved low-lying energy levels determined from solar coronal forbidden and spin-forbidden lines in the 500-1500 A range

    SciTech Connect (OSTI)

    Feldman, U.; Doschek, G.A. . E-mail: george.doschek@nrl.navy.mil

    2007-09-15

    We list observed parity-forbidden and spin-forbidden lines in the 500-1600 A range emitted by solar coronal plasmas and derive improved energy levels from their wavelengths. The lines, emitted by astrophysical abundant elements, belong to transitions within the ground configurations of the type ns{sup 2} np {sup k}, for n = 2, 3 and k = 0-5, and between the lowest term of the first excited configuration 2s2p {sup k+1} and the 2s{sup 2}2p {sup k} ground configurations for k = 0, 1, 2. For each line we give the newly measured wavelength, and the measured or predicted wavelength from the NIST Atomic Spectra Database (ASD) (which except for a few cases includes the previously reported compilation of Kaufman and Sugar [J. Phys. Chem. Ref. Data 15 (1986) 321]), and the values of the transition probability taken from the ASD and CHIANTI database. The list contains measured wavelengths of 136 lines of which over 100 were not available for the Kaufman and Sugar compilation. In addition we provide energy levels that were derived from the reported lines.

  10. Cross Section and Parity-Violating Spin Asymmetries of W± Boston Production in Polarized p + p Collisions at √sNN = 500 GeV

    SciTech Connect (OSTI)

    Adare, A.; PHENIX Collaboration

    2011-02-11

    Large parity-violating longitudinal single-spin asymmetries A{sub L}{sup e+} = -0.86{sub -0.14}{sup +0.30} and A{sub L}{sup e-} = 0.88{sub -0.71}{sup +0.12} are observed for inclusive high transverse momentum electrons and positrons in polarized p+p collisions at a center-of-mass energy of {radical}s = 500 GeV with the PHENIX detector at RHIC. These e{sup {+-}} come mainly from the decay of W{sup {+-}} and Z{sup 0} bosons, and their asymmetries directly demonstrate parity violation in the couplings of the W{sup {+-}} to the light quarks. The observed electron and positron yields were used to estimate W{sup {+-}} boson production cross sections for the e{sup {+-}} channels of {sigma}(pp {yields} W{sup +}X) x BR(W{sup +} e{sup +}v{sub e}) 144.1 {+-} 21.2(stat){sub -10.3}{sup +3.4}(syst) {+-} 21.6(norm) pb, and {sigma}(pp {yields} W{sup -}X) x BR(W{sup -} {yields} e{sup -}v{sup -}) = 31.7 {+-} 12.1(stat){sub -8.2}{sup +10.1}(syst) {+-} 4.8(norm) pb.

  11. Berkshire Gas - Residential Energy Efficiency Rebate Program...

    Broader source: Energy.gov (indexed) [DOE]

    400 Storage Water Heaters: 100 Condensing Stand Alone Water Heaters: 500 Tankless Water Heaters: 500 - 800 Heat Recovery Ventilator: 500 After-Market Boiler Reset...

  12. Evaluation of Using Caged Clams to Monitor Contaminated Groundwater Exposure in the Near-Shore Environment of the Hanford Site 300 Area

    SciTech Connect (OSTI)

    Larson, Kyle B.; Poston, Ted M.; Tiller, Brett L.

    2008-01-31

    The Asiatic clam (Corbicula fluminea) has been identified as an indicator species for locating and monitoring contaminated groundwater in the Columbia River. Pacific Northwest National Laboratory conducted a field study to explore the use of caged Asiatic clams to monitor contaminated groundwater upwelling in the 300 Area near-shore environment and assess seasonal differences in uranium uptake in relation to seasonal flow regimes of the Columbia River. Additional objectives included examining the potential effects of uranium accumulation on growth, survival, and tissue condition of the clams. This report documents the field conditions and procedures, laboratory procedures, and statistical analyses used in collecting samples and processing the data. Detailed results are presented and illustrated, followed by a discussion comparing uranium concentrations in Asiatic clams collected at the 300 Area and describing the relationship between river discharge, groundwater indicators, and uranium in clams. Growth and survival, histology, and other sources of environmental variation also are discussed.

  13. Human Health and Ecological Risk Assessment for the Operation of the Explosives Waste Treatment Facility at Site 300 of the Lawrence Livermore National Laboratory

    SciTech Connect (OSTI)

    Gallegos, G; Daniels, J; Wegrecki, A

    2007-10-01

    This document contains the human health and ecological risk assessment for the Resource Recovery and Conservation Act (RCRA) permit renewal for the Explosives Waste Treatment Facility (EWTF). Volume 1 is the text of the risk assessment, and Volume 2 (provided on a compact disc) is the supporting modeling data. The EWTF is operated by the Lawrence Livermore National Laboratory (LLNL) at Site 300, which is located in the foothills between the cities of Livermore and Tracy, approximately 17 miles east of Livermore and 8 miles southwest of Tracy. Figure 1 is a map of the San Francisco Bay Area, showing the location of Site 300 and other points of reference. One of the principal activities of Site 300 is to test what are known as 'high explosives' for nuclear weapons. These are the highly energetic materials that provide the force to drive fissionable material to criticality. LLNL scientists develop and test the explosives and the integrated non-nuclear components in support of the United States nuclear stockpile stewardship program as well as in support of conventional weapons and the aircraft, mining, oil exploration, and construction industries. Many Site 300 facilities are used in support of high explosives research. Some facilities are used in the chemical formulation of explosives; others are locations where explosive charges are mechanically pressed; others are locations where the materials are inspected radiographically for such defects as cracks and voids. Finally, some facilities are locations where the machined charges are assembled before they are sent to the onsite test firing facilities, and additional facilities are locations where materials are stored. Wastes generated from high-explosives research are treated by open burning (OB) and open detonation (OD). OB and OD treatments are necessary because they are the safest methods for treating explosives wastes generated at these facilities, and they eliminate the requirement for further handling and transportation that would be required if the wastes were treated off site.

  14. System-Scale Model of Aquifer, Vadose Zone, and River Interactions for the Hanford 300 Area - Application to Uranium Reactive Transport

    SciTech Connect (OSTI)

    Rockhold, Mark L.; Bacon, Diana H.; Freedman, Vicky L.; Parker, Kyle R.; Waichler, Scott R.; Williams, Mark D.

    2013-10-01

    This report represents a synthesis and integration of basic and applied research into a system-scale model of the Hanford 300 Area groundwater uranium plume, supported by the U.S. Department of Energys Richland Operations (DOE-RL) office. The report integrates research findings and data from DOE Office of Science (DOE-SC), Office of Environmental Management (DOE-EM), and DOE-RL projects, and from the site remediation and closure contractor, Washington Closure Hanford, LLC (WCH). The three-dimensional, system-scale model addresses water flow and reactive transport of uranium for the coupled vadose zone, unconfined aquifer, and Columbia River shoreline of the Hanford 300 Area. The system-scale model of the 300 Area was developed to be a decision-support tool to evaluate processes of the total system affecting the groundwater uranium plume. The model can also be used to address what if questions regarding different remediation endpoints, and to assist in design and evaluation of field remediation efforts. For example, the proposed cleanup plan for the Hanford 300 Area includes removal, treatment, and disposal of contaminated sediments from known waste sites, enhanced attenuation of uranium hot spots in the vadose and periodically rewetted zone, and continued monitoring of groundwater with institutional controls. Illustrative simulations of polyphosphate infiltration were performed to demonstrate the ability of the system-scale model to address these types of questions. The use of this model in conjunction with continued field monitoring is expected to provide a rigorous basis for developing operational strategies for field remediation and for defining defensible remediation endpoints.

  15. TECHNICAL EVALUATION OF SOIL REMEDIATION ALTERNATIVES AT THE BUILDING 812 OPERABLE UNIT, LAWRENCE LIVERMORE NATIONAL LABORATORY SITE 300

    SciTech Connect (OSTI)

    Eddy-Dilek, C.; Miles, D.; Abitz, R.

    2009-08-14

    The Department of Energy Livermore Site Office requested a technical review of remedial alternatives proposed for the Building 812 Operable Unit, Site 300 at the Lawrence Livermore National Laboratory. The team visited the site and reviewed the alternatives proposed for soil remediation in the draft RI/FS and made the following observations and recommendations. Based on the current information available for the site, the team did not identify a single technology that would be cost effective and/or ecologically sound to remediate DU contamination at Building 812 to current remedial goals. Soil washing is not a viable alternative and should not be considered at the site unless final remediation levels can be negotiated to significantly higher levels. This recommendation is based on the results of soil washing treatability studies at Fernald and Ashtabula that suggest that the technology would only be effective to address final remediation levels higher than 50 pCi/g. The technical review team identified four areas of technical uncertainty that should be resolved before the final selection of a preferred remedial strategy is made. Areas of significant technical uncertainty that should be addressed include: (1) Better delineation of the spatial distribution of surface contamination and the vertical distribution of subsurface contamination in the area of the firing table and associated alluvial deposits; (2) Chemical and physical characterization of residual depleted uranium (DU) at the site; (3) Determination of actual contaminant concentrations in air particulates to support risk modeling; and (4) More realistic estimation of cost for remedial alternatives, including soil washing, that were derived primarily from vendor estimates. Instead of conducting the planned soil washing treatability study, the team recommends that the site consider a new phased approach that combines additional characterization approaches and technologies to address the technical uncertainty in the remedial decision making. The site should redo the risk calculations as the future use scenario has changed for the site. As a result, the existing model is based on very conservative assumptions that result in calculation of unreasonably low cleanup goals. Specifically, the review team proposes that LLNL consider: (1) Revising the industrial worker scenario to a reasonable maximum exposure (RME) for a site worker that performs a weekly walk down of the area for two hours for 25 years (or an alternative RME if the exposure scenario changes); (2) Revising the ESSI of 2 mg U per kg soil for the deer mouse to account for less than 0.05 of the total ingested uranium being adsorbed by the gut; (3) Revising bioaccumulation factors (BAFs) for vegetation and invertebrates that are based on 100 mg of soluble uranium per kg of soil, as the uranium concentration in the slope soil does not average 100 mg/kg and it is not all in a soluble form; and (4) Measuring actual contaminant concentrations in air particulates at the site and using the actual values to support risk calculations. The team recommends that the site continue a phased approach during remediation. The activities should focus on elimination of the principal threats to groundwater by excavating (1) source material from the firing table and alluvial deposits, and (2) soil hotspots from the surrounding slopes with concentrations of U-235 and U-238 that pose unacceptable risk. This phased approach allows the remediation path to be driven by the results of each phase. This reduces the possibility of costly 'surprises', such as failure of soil treatment, and reduces the impact of remediation on endangered habitat. Treatment of the excavated material with physical separation equipment may result in a decreased volume of soil for disposal if the DU is concentrated in the fine-grained fraction, which can then be disposed of in an offsite facility at a considerable cost savings. Based on existing data and a decision to implement the recommended phased approach, the cost of characterization, excavation and physical

  16. Edge electroluminescence of the effective silicon point-junction light-emitting diode in the temperature range 80-300 K

    SciTech Connect (OSTI)

    Emel'yanov, A. M. [Russian Academy of Sciences, Ioffe Physicotechnical Institute (Russian Federation)], E-mail: Emelyanov@mail.ioffe.ru

    2008-11-15

    The edge electroluminescence spectra of silicon point-junction light-emitting diodes with a p-n junction area of 0.008 mm{sup 2} are studied at temperatures ranging from 80 to 300 K. Unprecedentedly high stability of the position of the spectral peak is observed at temperatures in the range between 130 and 300 K. The spectral characteristics of the light emitting diodes are studied at 80 K at different current densities up to 25 kA/cm{sup 2}. In contrast to the earlier reported data obtained at 300 K, the data obtained at 80 K do not show any noticeable Augerrecombination-related decrease in the quantum efficiency. From an analysis of the electroluminescence spectra at 80 K in a wide range of currents, it follows that radiative annihilation of free excitons is not a governing mechanism of electroluminescence in the entire emitting region in the base of the point-junction light-emitting diode at all currents used in the experiment.

  17. Measurement and control system for cryogenic helium gas bearing turbo-expander experimental platform based on Siemens PLC S7-300

    SciTech Connect (OSTI)

    Li, J.; Xiong, L. Y.; Peng, N.; Dong, B.; Liu, L. Q.; Wang, P.

    2014-01-29

    An experimental platform for cryogenic Helium gas bearing turbo-expanders is established at the Technical Institute of Physics and Chemistry, Chinese Academy of Sciences. This turbo-expander experimental platform is designed for performance testing and experimental research on Helium turbo-expanders with different sizes from the liquid hydrogen temperature to the room temperature region. A measurement and control system based on Siemens PLC S7-300 for this turbo-expander experimental platform is developed. Proper sensors are selected to measure such parameters as temperature, pressure, rotation speed and air flow rate. All the collected data to be processed are transformed and transmitted to S7-300 CPU. Siemens S7-300 series PLC CPU315-2PN/DP is as master station and two sets of ET200M DP remote expand I/O is as slave station. Profibus-DP field communication is established between master station and slave stations. The upper computer Human Machine Interface (HMI) is compiled using Siemens configuration software WinCC V6.2. The upper computer communicates with PLC by means of industrial Ethernet. Centralized monitoring and distributed control is achieved. Experimental results show that this measurement and control system has fulfilled the test requirement for the turbo-expander experimental platform.

  18. Case Study of Anomalies Encountered During Remediation of Mixed Low-Level Waste Burial Grounds in the 100 and 300 Areas of the Hanford Site

    SciTech Connect (OSTI)

    Haass, M.J.; Zacharias, P.E.; Zacharias, A.E.

    2007-07-01

    Under the U.S. Department of Energy's River Corridor Closure Project, Washington Closure Hanford has completed remediation of more than 10 mixed low-level waste burial grounds in the 100 and 300 Areas of the Hanford Site. The records of decision for the burial grounds required excavation, characterization, and transport of contaminated material to a Resource Conservation and Recovery Act of 1976-compliant hazardous waste landfill. This paper discusses a sample of the anomalous waste found during remediation and provides an overview of the waste excavation activities. The 100 Area burial grounds received plutonium production reactor waste and waste associated with various test programs. Examples of 100 Area anomalies include spent nuclear fuel, elemental mercury, reactor hardware, and the remains of animals used in testing the effects of radionuclides on living organisms. The 300 Area burial grounds received waste from research and development laboratories and fuel manufacturing operations. Of the seven 300 Area burial grounds remediated to date, the most challenging has been the 618-2 Burial Ground. It presented significant challenges because of the potential for airborne alpha contamination and the discovery of plutonium in an isotopically pure form. Anomalies encountered in the 618-2 Burial Ground included a combination safe that contained gram quantities of plutonium, miscellaneous containers of unknown liquids, and numerous types of shielded shipping casks. Information presented in this paper will be an aid to those involved in remediation activities throughout the U.S. Department of Energy complex and at other nuclear waste disposal sites. (authors)

  19. THE PROPERTIES OF THE 500 K DWARF UGPS J072227.51-054031.2 AND A STUDY OF THE FAR-RED FLUX OF COLD BROWN DWARFS

    SciTech Connect (OSTI)

    Leggett, S. K.; Saumon, D.; Marley, M. S.; Lodders, K.; Fegley, B.; Canty, J.; Lucas, P.; Burningham, Ben; Jones, H. R. A.; Marocco, F.; Pinfield, D. J.; Smart, R. L.; Homeier, D.; Allard, F.; Day-Jones, A.; Ishii, Miki; Tamura, M.

    2012-04-01

    We present i and z photometry for 25 T dwarfs and 1 L dwarf. Combined with published photometry, the data show that the i - z, z - Y, and z - J colors of T dwarfs are very red, and continue to increase through to the late-type T dwarfs, with a hint of a saturation for the latest types with T{sub eff} Almost-Equal-To 600 K. We present new 0.7-1.0 {mu}m and 2.8-4.2 {mu}m spectra for the very late type T dwarf UGPS J072227.51-054031.2, as well as improved astrometry for this dwarf. Examination of the spectral energy distribution using new and published data, with Saumon and Marley models, shows that the dwarf has T{sub eff} = 505 {+-} 10 K, a mass of 3-11 M{sub Jupiter}, and an age between 60 Myr and 1 Gyr. This young age is consistent with the thin disk kinematics of the dwarf. The mass range overlaps with that usually considered to be planetary, despite this being an unbound object discovered in the field near the Sun. This apparently young rapid rotator is also undergoing vigorous atmospheric mixing, as determined by the IRAC and WISE 4.5 {mu}m photometry and the Saumon and Marley models. The optical spectrum for this 500 K object shows clearly detected lines of the neutral alkalis Cs and Rb, which are emitted from deep atmospheric layers with temperatures of 900-1200 K.

  20. Spectra of atomic sulfur {sup 1}D in transitions to autoionizing Rydberg states in the region of 75 800-89 500 cm{sup -1}

    SciTech Connect (OSTI)

    Pan, W.-C.; Chen, I-C.; Huang, T.-P.; Yuh, J.-Y.; Lee, Y.-Y.

    2008-10-07

    We recorded photoionization spectra of sulfur atoms in transitions from state {sup 1}D in the range of 75 800-89 500 cm{sup -1}. Dissociation of CS{sub 2} after photolysis at 193 nm produced these sulfur atoms in a singlet excited state; they were then ionized with synchrotron radiation (NSRRC, beamline U9CGM) at resolution of up to 3 cm{sup -1} and detected with a quadruple mass filter. Rydberg series 3s{sup 2}3p{sup 3}({sup 2}D{sub 3/2}{sup 0})nd[3/2] and 3s{sup 2}3p{sup 3}({sup 2}D{sub 5/2}{sup 0})ns[5/2] with n extending to 16 and 32, respectively, to limit {sup 2}D{sup 0} are assigned. New Rydberg series 3s{sup 2}3p{sup 3}({sup 2}D{sub 3/2}{sup 0})nd[1/2]{sub 1}, ({sup 2}D{sub 5/2}{sup 0})nd[5/2], and ({sup 2}D{sub 3/2}{sup 0})nd[5/2] with n from 5-9 for the former two series and 7-13 for the latter are assigned. A new Rydberg line at 85 335 cm{sup -1} is assigned to 3s{sup 2}3p{sup 3}({sup 2}D{sub 3/2}{sup 0})6d {sup 1}P.

  1. Evaluation of the ²³⁹Pu prompt fission neutron spectrum induced by neutrons of 500 keV and associated covariances

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Neudecker, D.; Talou, P.; Kawano, T.; Smith, D. L.; Capote, R.; Rising, M. E.; Kahler, A. C.

    2015-08-01

    We present evaluations of the prompt fission neutron spectrum (PFNS) of ²³⁹Pu induced by 500 keV neutrons, and associated covariances. In a previous evaluation by Talou et al. 2010, surprisingly low evaluated uncertainties were obtained, partly due to simplifying assumptions in the quantification of uncertainties from experiment and model. Therefore, special emphasis is placed here on a thorough uncertainty quantification of experimental data and of the Los Alamos model predicted values entering the evaluation. In addition, the Los Alamos model was extended and an evaluation technique was employed that takes into account the qualitative differences between normalized model predicted valuesmore » and experimental shape data. These improvements lead to changes in the evaluated PFNS and overall larger evaluated uncertainties than in the previous work. However, these evaluated uncertainties are still smaller than those obtained in a statistical analysis using experimental information only, due to strong model correlations. Hence, suggestions to estimate model defect uncertainties are presented, which lead to more reasonable evaluated uncertainties. The calculated keff of selected criticality benchmarks obtained with these new evaluations agree with each other within their uncertainties despite the different approaches to estimate model defect uncertainties. The keff one standard deviations overlap with some of those obtained using ENDF/B-VII.1, albeit their mean values are further away from unity. Spectral indexes for the Jezebel critical assembly calculated with the newly evaluated PFNS agree with the experimental data for selected (n,γ) and (n,f) reactions, and show improvements for high-energy threshold (n,2n) reactions compared to ENDF/B-VII.1.« less

  2. Evaluation of the ²³⁹Pu prompt fission neutron spectrum induced by neutrons of 500 keV and associated covariances

    SciTech Connect (OSTI)

    Neudecker, D.; Talou, P.; Kawano, T.; Smith, D. L.; Capote, R.; Rising, M. E.; Kahler, A. C.

    2015-08-01

    We present evaluations of the prompt fission neutron spectrum (PFNS) of ²³⁹Pu induced by 500 keV neutrons, and associated covariances. In a previous evaluation by Talou et al. 2010, surprisingly low evaluated uncertainties were obtained, partly due to simplifying assumptions in the quantification of uncertainties from experiment and model. Therefore, special emphasis is placed here on a thorough uncertainty quantification of experimental data and of the Los Alamos model predicted values entering the evaluation. In addition, the Los Alamos model was extended and an evaluation technique was employed that takes into account the qualitative differences between normalized model predicted values and experimental shape data. These improvements lead to changes in the evaluated PFNS and overall larger evaluated uncertainties than in the previous work. However, these evaluated uncertainties are still smaller than those obtained in a statistical analysis using experimental information only, due to strong model correlations. Hence, suggestions to estimate model defect uncertainties are presented, which lead to more reasonable evaluated uncertainties. The calculated keff of selected criticality benchmarks obtained with these new evaluations agree with each other within their uncertainties despite the different approaches to estimate model defect uncertainties. The keff one standard deviations overlap with some of those obtained using ENDF/B-VII.1, albeit their mean values are further away from unity. Spectral indexes for the Jezebel critical assembly calculated with the newly evaluated PFNS agree with the experimental data for selected (n,γ) and (n,f) reactions, and show improvements for high-energy threshold (n,2n) reactions compared to ENDF/B-VII.1.

  3. Results of U-xMo (x=7, 10, 12 wt.%) Alloy versus Al-6061 Cladding Diffusion Couple Experiments Performed at 500, 550 and 600 Degrees C

    SciTech Connect (OSTI)

    Emmanuel Perez; Dennis D. Keiser, Jr.; Yongho Sohn

    2013-04-01

    The Reduced Enrichment for Research and Test Reactors (RERTR) program has been developing low enrichment fuel systems encased in Al 6061 for use in research and test reactors. U–Mo alloys in contact with Al and Al alloys can undergo diffusional interactions that can result in the development of interdiffusion zones with complex fine-grained microstructures composed of multiple phases. A monolithic fuel currently being developed by the RERTR program has local regions where the U–Mo fuel plate is in contact with the Al 6061 cladding and, as a result, the program finds information about interdiffusion zone development at high temperatures of interest. In this study, the microstructural development of diffusion couples consisting of U-7wt.%Mo, U-10wt.%Mo, and U-12wt.%Mo vs. Al 6061 (or 6061 aluminum) cladding, annealed at 500, 550, 600 degrees C for 1, 5, 20, 24, or 132 hours, was analyzed by backscatter electron microscopy and x-ray energy dispersive spectroscopy on a scanning electron microscope. Concentration profiles were determined by standardized wavelength dispersive spectroscopy and standardless x-ray energy dispersive spectroscopy. The results of this work shows that the presence of surface layers at the U–Mo/Al 6061 interface can dramatically impact the overall interdiffusion behavior in terms of rate of interaction and uniformity of the developed interdiffusion zones. It further reveals that relatively uniform interaction layers with higher Si concentrations can develop in U–Mo/Al 6061 couples annealed at shorter times and that longer times at temperature result in the development of more non-uniform interaction layers with more areas that are enriched in Al. At longer annealing times and relatively high temperatures, U–Mo/Al 6061 couples can exhibit more interaction compared to U–Mo/pure Al couples. The minor alloying constituents in Al 6061 cladding can result in the development of many complex phases in the interaction layer of U–Mo/Al–6061 cladding couples, and some phases in the interdiffusion zones of U–Mo/Al–6061 cladding couples are likely similar to those observed for U–Mo/pure Al couples.

  4. Modeling of collision-induced infrared absorption spectra of H2-H2 pairs in the fundamental band at temperatures from 20 to 300 K. [Planetary atmospheres

    SciTech Connect (OSTI)

    Borysow, A. )

    1991-08-01

    The 20-300 K free-free rotovibrational collision-induced absorption (RV CIA) spectra of H2-H2 pairs are presently obtained by a numerical method which, in addition to closely matching known CIA spectra of H2-H2, can reproduce the results of the quantum-mechanical computations to within a few percent. Since the spectral lineshape parameters are derivable by these means from the lowest three quantum-mechanical spectral moments, these outer-planet atmosphere-pertinent model spectra may be computed on even small computers. 35 refs.

  5. Browse Draft Directives - DOE Directives, Delegations, and Requirements

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Browse Draft Directives Current Draft Archives by Website Administrator More filters Less filters Directive Type Order Guide Manual Policy Notice HQ Order Sec of Energy Notice Justification Memorandum Certification Memo 0 Series Series All 0000 Subject Classification 100 Leadership/Management Planning 200 Information and Analysis 300 Human Resources 400 Work Processes 500 Business and Support Services 1100 Org. Authorities, Functions and Internal Relationships 1200 External Relationships 1300

  6. Slide 1

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Principles Simulation and Model-Driven Isotopic Labeling Experiments Reveal Biomass Decomposition Pathways 1 Theory driven experimental confirmation Intensity (arb. units) 600 550 500 450 400 350 300 250 Temperature (K) H 2 (2amu) background DOCH 2 CH 2 OD HOCD 2 CD 2 OH 398K 322K 346K 432K (A) * Density functional theory (DFT) calculations of ethylene glycol decomposition on Pt(111) and Ni/Pt(111) reveal key differences between decomposition of highly functionalized oxygenates compared to

  7. Appendix 6 of 6

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    6 of 6 Federal Fiscal year 2002 budget related documentation 1. ORP budget requirements 2. President's approved FY2002 budget - Conference Committee Report 3. November 27, 2001 letter from Assistant Secretary Roberson (FY2002 budget allocation) OFFICE OF RIVER PROTECTION FUNDING REQUIREMENTS AS OF FEBRUARY, 2002 Waste Treatment Plant (WTP) Requirements per approved BNI Baseline (Dollars in Millions) 0 100 200 300 400 500 600 700 800 900 1000 Beg. Balance Carryover 0 175 281 60 0 0 0 0 0 0 0

  8. Selection Tests of MnZn and NiZn Ferrites for Mu2e 300 kHz and 5.1 MHz AC Dipoles

    SciTech Connect (OSTI)

    Bourkland, K.; Elementi, L.; Feher, S.; Harding, D.J.; Kashikhin, V.S.; Makarov, A.; Pfeffer, H.; Velev, G.V.; Mulushev, E.; Iedmeska, I.; Venturini, M.; /Pisa U.

    2011-09-09

    Mu2e, a charged lepton flavor violation (CLFV) experiment is planned to start at Fermilab late in this decade. The proposed experiment will search for neutrinoless muon to electron conversions with unprecedented sensitivity, better than 6 x 10{sup -17 }at 90% CL. To achieve this sensitivity the incoming proton beam must be highly suppressed during the window for detecting the muon decays. The current proposal for beam extinction is based on a collimator design with two dipoles running at {approx}300 kHz and 5.1 MHz and synchronized to the proton bunch spacing. The appropriate choice of ferrite material for the magnet yoke is a critical step in the overall design of the dipoles and their reliable operation at such high frequencies over the life of the experiment. This choice, based on a series of the thermal and magnetic measurements of the ferrite samples, is discussed in the paper. Additionally, the first results from the testing at 300 kHz of a prototype AC dipole are presented.

  9. Final Technical Report - 300???°C Capable Electronics Platform and Temperature Sensor System For Enhanced Geothermal Systems

    SciTech Connect (OSTI)

    Cheng-Po Chen; David Shaddock; Peter Sandvik; Rich Saia; Amita Patil, Alexey Vert; Tan Zhang

    2012-11-30

    A silicon carbide (SiC) based electronic temperature sensor prototype has been demonstrated to operate at 300???°C. We showed continuous operation of 1,000 hours with SiC operational amplifier and surface mounted discreet resistors and capacitors on a ceramic circuit board. This feasibility demonstration is a major milestone in the development of high temperature electronics in general and high temperature geothermal exploration and well management tools in particular. SiC technology offers technical advantages that are not found in competing technologies such as silicon-on-insulator (SOI) at high temperatures of 200???°C to 300???°C and beyond. The SiC integrated circuits and packaging methods can be used in new product introduction by GE Oil and Gas for high temperature down-hole tools. The existing SiC fabrication facility at GE is sufficient to support the quantities currently demanded by the marketplace, and there are other entities in the United States and other countries capable of ramping up SiC technology manufacturing. The ceramic circuit boards are different from traditional organic-based electronics circuit boards, but the fabrication process is compatible with existing ceramic substrate manufacturing. This project has brought high temperature electronics forward, and brings us closer to commercializing tools that will enable and reduce the cost of enhanced geothermal technology to benefit the public in terms of providing clean renewable energy at lower costs.

  10. The Multi-Scale Mass Transfer Processes Controlling Natural Attenuation and Engineered Remediation: An IFC Focused on Hanfords 300 Area Uranium Plume Quality Assurance Project Plan

    SciTech Connect (OSTI)

    Fix, N. J.

    2008-01-31

    The purpose of the project is to conduct research at an Integrated Field-Scale Research Challenge Site in the Hanford Site 300 Area, CERCLA OU 300-FF-5 (Figure 1), to investigate multi-scale mass transfer processes associated with a subsurface uranium plume impacting both the vadose zone and groundwater. The project will investigate a series of science questions posed for research related to the effect of spatial heterogeneities, the importance of scale, coupled interactions between biogeochemical, hydrologic, and mass transfer processes, and measurements/approaches needed to characterize a mass-transfer dominated system. The research will be conducted by evaluating three (3) different hypotheses focused on multi-scale mass transfer processes in the vadose zone and groundwater, their influence on field-scale U(VI) biogeochemistry and transport, and their implications to natural systems and remediation. The project also includes goals to 1) provide relevant materials and field experimental opportunities for other ERSD researchers and 2) generate a lasting, accessible, and high-quality field experimental database that can be used by the scientific community for testing and validation of new conceptual and numerical models of subsurface reactive transport.

  11. Experimental determination of single-crystal halite thermal conductivity, diffusivity and specific heat from -75°C to 300°C

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Urquhart, Alexander; Bauer, Stephen

    2015-05-19

    The thermal properties of halite have broad practical importance, from design and long-term modeling of nuclear waste repositories to analysis and performance assessment of underground natural gas, petroleum and air storage facilities. Using a computer-controlled transient plane source method, single-crystal halite thermal conductivity, thermal diffusivity and specific heat were measured from -75°C to 300°C. These measurements reproduce historical high-temperature experiments and extend the lower temperature extreme into cryogenic conditions. Measurements were taken in 25-degree increments from -75°C to 300°C. Over this temperature range, thermal conductivity decreases by a factor of 3.7, from 9.975 to 2.699 W/mK , and thermal diffusivitymore » decreases by a factor of 3.6, from 5.032 to 1.396 mm²/s. Specific heat does not appear to be temperature dependent, remaining near 2.0 MJ/m³K at all temperatures. This work is intended to develop and expand the existing dataset of halite thermal properties, which are of particular value in defining the parameters of salt storage thermophysical models. The work was motivated by a need for thermal conductivity values in a mixture theory model used to determine bulk thermal conductivity of reconsolidating crushed salt.« less

  12. Experimental determination of single-crystal halite thermal conductivity, diffusivity and specific heat from -75°C to 300°C

    SciTech Connect (OSTI)

    Urquhart, Alexander; Bauer, Stephen

    2015-05-19

    The thermal properties of halite have broad practical importance, from design and long-term modeling of nuclear waste repositories to analysis and performance assessment of underground natural gas, petroleum and air storage facilities. Using a computer-controlled transient plane source method, single-crystal halite thermal conductivity, thermal diffusivity and specific heat were measured from -75°C to 300°C. These measurements reproduce historical high-temperature experiments and extend the lower temperature extreme into cryogenic conditions. Measurements were taken in 25-degree increments from -75°C to 300°C. Over this temperature range, thermal conductivity decreases by a factor of 3.7, from 9.975 to 2.699 W/mK , and thermal diffusivity decreases by a factor of 3.6, from 5.032 to 1.396 mm²/s. Specific heat does not appear to be temperature dependent, remaining near 2.0 MJ/m³K at all temperatures. This work is intended to develop and expand the existing dataset of halite thermal properties, which are of particular value in defining the parameters of salt storage thermophysical models. The work was motivated by a need for thermal conductivity values in a mixture theory model used to determine bulk thermal conductivity of reconsolidating crushed salt.

  13. FINAL PROJECT REPORT: A Geophysical Characterization & Monitoring Strategy for Determining Hydrologic Processes in the Hyporheic Corridor at the Hanford 300-Area

    SciTech Connect (OSTI)

    Lee Slater

    2011-08-15

    The primary objective of this research was to advance the prediction of solute transport between the Uranium contaminated Hanford aquifer and the Columbia River at the Hanford 300 Area by improving understanding of how fluctuations in river stage, combined with subsurface heterogeneity, impart spatiotemporal complexity to solute exchange along the Columbia River corridor. Our work explored the use of continuous waterborne electrical imaging (CWEI), in conjunction with fiber-optic distributed temperature sensor (FO-DTS) and time-lapse resistivity monitoring, to improve the conceptual model for how groundwater/surface water exchange regulates uranium transport. We also investigated how resistivity and induced polarization can be used to generate spatially rich estimates of the variation in depth to the Hanford-Ringold (H-R) contact between the river and the 300 Area Integrated Field Research Challenge (IFRC) site. Inversion of the CWEI datasets (a data rich survey containing ~60,000 measurements) provided predictions of the distributions of electrical resistivity and polarizability, from which the spatial complexity of the primary hydrogeologic units along the river corridor was reconstructed. Variation in the depth to the interface between the overlying coarse-grained, high permeability Hanford Formation and the underlying finer-grained, less permeable Ringold Formation, an important contact that limits vertical migration of contaminants, has been resolved along ~3 km of the river corridor centered on the IFRC site in the Hanford 300 Area. Spatial variability in the thickness of the Hanford Formation captured in the CWEI datasets indicates that previous studies based on borehole projections and drive-point and multi-level sampling likely overestimate the contributing area for uranium exchange within the Columbia River at the Hanford 300 Area. Resistivity and induced polarization imaging between the river and the 300 Area IFRC further imaged spatial variability in the depth to the Hanford-Ringold inland over a critical region where borehole information is absent, identifying evidence for a continuous depression in the H-R contact between the IFRC and the river corridor. Strong natural contrasts in temperature and specific conductance of river water compared to groundwater at this site, along with periodic river stage fluctuations driven by dam operations, were exploited to yield new insights into the dynamics of groundwater-surface water interaction. Whereas FO-DTS datasets have provided meter-scale measurements of focused groundwater discharge at the riverbed along the corridor, continuous resistivity monitoring has non-invasively imaged spatiotemporal variation in the resistivity inland driven by river stage fluctuations. Time series and time-frequency analysis of FO-DTS and 3D resistivity datasets has provided insights into the role of forcing variables, primarily daily dam operations, in regulating the occurrence of focused exchange at the riverbed and its extension inland. High amplitudes in the DTS and 3D resistivity signals for long periods that dominate the stage time series identify regions along the corridor where stage-driven exchange is preferentially focused. Our work has demonstrated how time-series analysis of both time-lapse resistivity and DTS datasets, in conjunction with resistivity/IP imaging of lithology, can improve understanding of groundwater-surface water exchange along river corridors, offering unique opportunities to connect stage-driven groundwater discharge observed with DTS on the riverbed to stage-driven groundwater and solute fluctuations captured with resistivity inland.

  14. Characterisation of amorphous silica in air-oxidised Ti3SiC2 at 500-1000 °C using secondary-ion mass spectrometry, nuclear magnetic resonance and transmission electron microscopy

    SciTech Connect (OSTI)

    Pang, W K; Low, I M; Hanna, J V

    2010-05-18

    In this paper we have described the use of secondary-ion mass spectrometry (SIMS), solid state {sup 29}Si magic-angle-spinning (MAS) nuclear magnetic resonance (NMR) and transmission electron microscopy (TEM) to detect the existence of amorphous silica in Ti{sub 3}SiC{sub 2} oxidised at 500-1000 C. The formation of amorphous SiO{sub 2} and growth of crystalline TiO{sub 2} with temperature was monitored using dynamic SIMS and synchrotron radiation diffraction. A duplex structure with an outer TiO{sub 2}-rich layer and an inner mixed layer of SiO{sub 2} and TiO{sub 2} was observed. Results of NMR and TEM verified for the first time the direct evidence of amorphous silica formation during the oxidation of Ti{sub 3}SiC{sub 2} at the temperature range 500-1000 C.

  15. Use of Electrical Imaging and Distributed Temperature Sensing Methods to Characterize Surface Water-Groundwater Exchange Regulating Uranium Transport at the Hanford 300 Area, Washington

    SciTech Connect (OSTI)

    Slater, Lee; Ntarlagiannis, Dimitrios; Day-Lewis, Frederick D.; Mwakanyamale, Kisa; Versteeg, Roelof J.; Ward, Anderson L.; Strickland, Christopher E.; Johnson, Carole D.; Lane, John W.

    2010-10-31

    A critical challenge in advancing prediction of solute transport between contaminated aquifers and rivers is improving understanding of how fluctuations in river stage, combined with subsurface heterogeneity, impart spatiotemporal complexity to solute exchange along river corridors. Here, we explored the use of waterborne geoelectrical imaging, in conjunction with fiber-optic distributed temperature sensor (DTS) monitoring, to improve the conceptual model for uranium transport within the hyporheic corridor at the Hanford 300 Area. We first inverted waterborne geoelectrical (resistivity and induced polarization) datasets for distributions of electrical resistivity and polarizability, from which the spatial complexity of the primary hydrogeologic units was reconstructed. Variations in the depth to the interface between the overlying coarse-grained, high permeability Hanford formation and the underlying finer-grained, less permeable Ringold formation, an important contact that limits vertical migration of contaminants, were resolved along ~3 km of the river corridor centered on the 300 Area. Polarizability images were translated into lithologic images using established relationships between polarizability and surface area normalized to pore volume (Spor). The spatial variability captured in the geoelectrical datasets indicates that previous studies based on borehole projections and point probing overestimate the contributing area for uranium exchange within the Columbia River at the Hanford 300 Area. The DTS data recorded on 1. 5 km of cable with a 1 m spatial resolution and 5 minute sampling interval revealed sub-reaches showing (1) high temperature anomalies and, (2) a strong negative correlation between temperature and river stage, both indicative of groundwater influxes during winter months. The DTS datasets confirm the hydrologic significance of the variability identified in the geoelectrical imaging and reveal a pattern of highly focused hyporheic exchange, with exchange concentrated at springs where the Hanford formation is thick, and coinciding with a paleochannel identified in ground penetrating radar surveys at one location. No evidence for focused hyporheic exchange is observed in the DTS data where the Ringold unit is in contact with the riverbed. Our findings illustrate how the combination of waterborne geoelectrical imaging and DTS technologies can characterize hyporheic exchange in a complex, coupled river-aquifer system.

  16. Laboratory-Scale Column Testing Using IONSIV IE-911 for Removing Cesium from Acidic Tank Waste Simulant. 2: Determination of Cesium Exchange Capacity and Effective Mass Transfer Coefficient from a 500-cm3 Column Experiement

    SciTech Connect (OSTI)

    T.J. Tranter; R.D. Tillotson; T.A. Todd

    2005-04-01

    A semi-scale column test was performed using a commercial form of crystalline silicotitanate (CST) for removing radio-cesium from a surrogate acidic tank solution, which represents liquid waste stored at the Idaho National Engineering and Environmental Laboratory (INEEL). The engineered form of CST ion exchanger, known as IONSIVtmIE-911 (UOP, Mt. Laurel,NJ, USA), was tested in a 500-cm3 column to obtain a cesium breakthrough curve. The cesium exchange capacity of this column matched that obtained from previous testing with a 15-mc3 column. A numerical algorithm using implicit finite difference approximations was developed to solve the governing mass transport equations for the CST columns. An effective mass transfer coefficient was derived from solving these equations for previously reported 15 cm3 tests. The effective mass transfer coefficient was then used to predict the cesium breakthrough curve for the 500-cm3 column and compared to the experimental data reported in this paper. The calculated breakthrough curve showed excellent agreement with the data from the 500-cm3 column even though the interstitial velocity was a factor of two greater. Thus, this approach should provide a reasonable method for scale up to larger columns for treating actual tank waste.

  17. Magnetic Nature of the 500 meV peak in La2−xSrxCuO4 Observed with Resonant Inelastic X-ray Scattering at the Cu K-edge

    SciTech Connect (OSTI)

    Hill, J.P.; Ellis, D.S.; Kim, J.; Wakimoto, S.; Birgeneau, R.J.; Shvyd’ko, Y.; Casa, D.; Gog, T.; Ishii, K.; Ikeuchi, K.; Paramekanti, A.; Kim, Y.-J.

    2010-02-15

    We present a comprehensive study of the temperature and doping dependence of the 500 meV peak observed at q = ({pi},0) in resonant inelastic x-ray scattering (RIXS) experiments on La{sub 2}CuO{sub 4}. The intensity of this peak persists above the Neel temperature (T{sub N} = 320 K), but decreases gradually with increasing temperature, reaching zero at around T = 500 K. The peak energy decreases with temperature in close quantitative accord with the behavior of the two-magnon B{sub 1g} Raman peak in La{sub 2}CuO{sub 4} and, with suitable rescaling, agrees with the Raman peak shifts in EuBa{sub 2}Cu{sub 3}O{sub 6} and K{sub 2}NiF{sub 4}. The overall dispersion of this excitation in the Brillouin zone is found to be in agreement with theoretical calculations for a two-magnon excitation. Upon doping, the peak intensity decreases analogous to the Raman mode intensity and appears to track the doping dependence of the spin-correlation length. Taken together, these observations strongly suggest that the 500 meV mode is magnetic in character and is likely a two-magnon excitation.

  18. Post-Closure Benefits: DOE Complex vs Closure Sites | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Post-Closure Benefits » Post-Closure Benefits: DOE Complex vs Closure Sites Post-Closure Benefits: DOE Complex vs Closure Sites Status of Contractor Pension and PRB Benefit Programs - September 30, 2013 DOE Wide Closure Sites Defined Benefit Pension Plans 36 6 Defined Contribution Plans 13 0 PRB Plans >100 7 Active Participants 61,400 0 Retirees/Survivors 75,300 6,400 Terminated Vested Participants 39,500 2,900 FY 2013 Pension Unfunded Liability 10,616 Million 0 Million FY 2013 PRB Unfunded

  19. Evaluation of Reagent Emplacement Techniques for Phosphate-based Treatment of the Uranium Contamination Source in the 300 Area White Paper

    SciTech Connect (OSTI)

    Nimmons, Michael J.

    2010-06-04

    Persistent uranium contamination of groundwater under the 300 Area of the Hanford Site has been observed. The source of the uranium contamination resides in uranium deposits on sediments at the groundwater interface, and the contamination is mobilized when periodically wetted by fluctuations of Columbia River levels. Treatability work is ongoing to develop and apply phosphate-containing reagents to promote the formation of stable and insoluble uranium phosphate minerals (i.e., autunite) and other phosphate precipitates (di-calcium phosphate, apatite) to stabilize the uranium source. Technologies for applying phosphate-containing reagents by vertical percolation and lateral injection into sediments of the periodically wetted groundwater interface are being investigated. This report is a preliminary evaluation of technologies for lateral injection.

  20. Structural Integrity Program for the 300,000-Gallon Radioactive Liquid Waste Storage Tanks at the Idaho Nuclear Technology and Engineering Center

    SciTech Connect (OSTI)

    Bryant, Jeffrey W.

    2010-08-12

    This report provides a record of the Structural Integrity Program for the 300,000-gal liquid waste storage tanks and associated equipment at the Idaho Nuclear Technology and Engineering Center, as required by U.S. Department of Energy M 435.1-1, “Radioactive Waste Management Manual.” This equipment is known collectively as the Tank Farm Facility. This report is an update, and replaces the previous report by the same title issued April 2003. The conclusion of this report is that the Tank Farm Facility tanks, vaults, and transfer systems that remain in service for storage are structurally adequate, and are expected to remain structurally adequate over the remainder of their planned service life through 2012. Recommendations are provided for continued monitoring of the Tank Farm Facility.

  1. Multi-Scale Mass Transfer Processes Controlling Natural Attenuation and Engineered Remediation: An IFRC Focused on Hanfords 300 Area Uranium Plume January 2011 to January 2012

    SciTech Connect (OSTI)

    Zachara, John M.; Bjornstad, Bruce N.; Christensen, John N.; Conrad, Mark S.; Fredrickson, Jim K.; Freshley, Mark D.; Haggerty, Roy; Hammond, Glenn E.; Kent, Douglas B.; Konopka, Allan; Lichtner, Peter C.; Liu, Chongxuan; McKinley, James P.; Murray, Christopher J.; Rockhold, Mark L.; Rubin, Yoram; Vermeul, Vincent R.; Versteeg, Roelof J.; Zheng, Chunmiao

    2012-03-05

    The Integrated Field Research Challenge (IFRC) at the Hanford Site 300 Area uranium (U) plume addresses multi-scale mass transfer processes in a complex subsurface biogeochemical setting where groundwater and riverwater interact. A series of forefront science questions on reactive mass transfer motivates research. These questions relate to the effect of spatial heterogeneities; the importance of scale; coupled interactions between biogeochemical, hydrologic, and mass transfer processes; and measurements and approaches needed to characterize and model a mass-transfer dominated biogeochemical system. The project was initiated in February 2007, with CY 2007, CY 2008, CY 2009, and CY 2010 progress summarized in preceding reports. A project peer review was held in March 2010, and the IFRC project acted upon all suggestions and recommendations made in consequence by reviewers and SBR/DOE. These responses have included the development of 'Modeling' and 'Well-Field Mitigation' plans that are now posted on the Hanford IFRC web-site, and modifications to the IFRC well-field completed in CY 2011. The site has 35 instrumented wells, and an extensive monitoring system. It includes a deep borehole for microbiologic and biogeochemical research that sampled the entire thickness of the unconfined 300 A aquifer. Significant, impactful progress has been made in CY 2011 including: (i) well modifications to eliminate well-bore flows, (ii) hydrologic testing of the modified well-field and upper aquifer, (iii) geophysical monitoring of winter precipitation infiltration through the U-contaminated vadose zone and spring river water intrusion to the IFRC, (iv) injection experimentation to probe the lower vadose zone and to evaluate the transport behavior of high U concentrations, (v) extended passive monitoring during the period of water table rise and fall, and (vi) collaborative down-hole experimentation with the PNNL SFA on the biogeochemistry of the 300 A Hanford-Ringold contact and the underlying redox transition zone. The modified well-field has functioned superbly without any evidence for well-bore flows. Beyond these experimental efforts, our site-wide reactive transport models (PFLOTRAN and eSTOMP) have been updated to include site geostatistical models of both hydrologic properties and adsorbed U distribution; and new hydrologic characterization measurements of the upper aquifer. These increasingly robust models are being used to simulate past and recent U desorption-adsorption experiments performed under different hydrologic conditions, and heuristic modeling to understand the complex functioning of the smear zone. We continued efforts to assimilate geophysical logging and 3D ERT characterization data into our site wide geophysical model, with significant and positive progress in 2011 that will enable publication in 2012. Our increasingly comprehensive field experimental results and robust reactive transport simulators, along with the field and laboratory characterization, are leading to a new conceptual model of U(VI) flow and transport in the IFRC footprint and the 300 Area in general, and insights on the microbiological community and associated biogeochemical processes influencing N, S, C, Mn, and Fe. Collectively these findings and higher scale models are providing a unique and unparalleled system-scale understanding of the biogeochemical function of the groundwater-river interaction zone.

  2. Note: On the generation of sub-300 keV flash-X-rays using rod-pinch diode: An experimental investigation

    SciTech Connect (OSTI)

    Satyanarayana, N.; Rajawat, R. K.; Basu, Shibaji; Rao, A. Durga Prasad; Mittal, K. C.

    2014-09-15

    Generation of flash X-rays (FXRs) at less than 500 keV is described with emphasis on experimental investigation. The pulser is a Tesla transformer-Water transmission line based pulsed power generator operating in double resonance mode to power a rod-pinch diode. The configuration of aspect ratio reported here falls much below the normally reported ratios for the rod-pinch diode operation. Experimental investigation at such low pulsed voltage has revealed flowering of the anode tip and pitting of the perspex window. A possible explanation in terms of Lorentz body force is discussed rather than the pinch mechanism generally suggested in literature. The experimental investigation for the FXR generation is corroborated by measuring the radiation dose using CaSO{sub 4} (Dy) thermo luminescent dosimeters.

  3. CM300DLFinal.doc

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Safety Understand the emergency shut - down procedure: SHUT GUN VALVE. Point out ... Remove a specimen holder. Gloves worn. Gun valve checked. Holder centered. ...

  4. Contract Modification 23100-A300

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

  5. Multi-Scale Mass Transfer Processes Controlling Natural Attenuation and Engineered Remediation: An IFRC Focused on Hanfords 300 Area Uranium Plume January 2010 to January 2011

    SciTech Connect (OSTI)

    Zachara, John M.; Bjornstad, Bruce N.; Christensen, John N.; Conrad, Mark S.; Fredrickson, Jim K.; Freshley, Mark D.; Haggerty, Roy; Hammond, Glenn E.; Kent, Douglas B.; Konopka, Allan; Lichtner, Peter C.; Liu, Chongxuan; McKinley, James P.; Murray, Christopher J.; Rockhold, Mark L.; Rubin, Yoram; Vermeul, Vincent R.; Versteeg, Roelof J.; Ward, Anderson L.; Zheng, Chunmiao

    2011-02-01

    The Integrated Field Research Challenge (IFRC) at the Hanford Site 300 Area uranium (U) plume addresses multi-scale mass transfer processes in a complex subsurface hydrogeologic setting where groundwater and riverwater interact. A series of forefront science questions on reactive mass transfer focus research. These questions relate to the effect of spatial heterogeneities; the importance of scale; coupled interactions between biogeochemical, hydrologic, and mass transfer processes; and measurements and approaches needed to characterize and model a mass-transfer dominated system. The project was initiated in February 2007, with CY 2007, CY 2008, and CY 2009 progress summarized in preceding reports. A project peer review was held in March 2010, and the IFRC project has responded to all suggestions and recommendations made in consequence by reviewers and SBR/DOE. These responses have included the development of Modeling and Well-Field Mitigation plans that are now posted on the Hanford IFRC web-site. The site has 35 instrumented wells, and an extensive monitoring system. It includes a deep borehole for microbiologic and biogeochemical research that sampled the entire thickness of the unconfined 300 A aquifer. Significant, impactful progress has been made in CY 2010 including the quantification of well-bore flows in the fully screened wells and the testing of means to mitigate them; the development of site geostatistical models of hydrologic and geochemical properties including the distribution of U; developing and parameterizing a reactive transport model of the smear zone that supplies contaminant U to the groundwater plume; performance of a second passive experiment of the spring water table rise and fall event with a associated multi-point tracer test; performance of downhole biogeochemical experiments where colonization substrates and discrete water and gas samplers were deployed to the lower aquifer zone; and modeling of past injection experiments for model parameterization, deconvolution of well-bore flow effects, system understanding, and publication. We continued efforts to assimilate geophysical logging and 3D ERT characterization data into our site wide geophysical model, and have now implemented a new strategy for this activity to bypass an approach that was found unworkable. An important focus of CY 2010 activities has been infrastructure modification to the IFRC site to eliminate vertical well bore flows in the fully screened wells. The mitigation procedure was carefully evaluated and is now being implementated. A new experimental campaign is planned for early spring 2011 that will utilize the modified well-field for a U reactive transport experiment in the upper aquifer zone. Preliminary geophysical monitoring experiments of rainwater recharge in the vadose zone have been initiated with promising results, and a controlled infiltration experiment to evaluate U mobilization from the vadose zone is now under planning for the September 2011. The increasingly comprehensive field experimental results, along with the field and laboratory characterization, are leading to a new conceptual model of U(VI) flow and transport in the IFRC footprint and the 300 Area in general, and insights on the microbiological community and associated biogeochemical processes.

  6. Multi-Scale Mass Transfer Processes Controlling Natural Attenuation and Engineered Remediation: An IFRC Focused on Hanford’s 300 Area Uranium Plume

    SciTech Connect (OSTI)

    Zachara, John M.; Bjornstad, Bruce N.; Christensen, John N.; Conrad, Mark E.; Fredrickson, Jim K.; Freshley, Mark D.; Haggerty, Roy; Hammon, Glenn; Kent, Douglas B.; Konopka, Allan; Lichtner, Peter C.; Liu, Chongxuan; McKinley, James P.; Murray, Christopher J.; Rockhold, Mark L.; Rubin, Yoram; Vermeul, Vincent R.; Versteeg, Roelof J.; Ward, Anderson L.; Zheng, Chunmiao

    2010-02-01

    The Integrated Field-Scale Subsurface Research Challenge (IFRC) at the Hanford Site 300 Area uranium (U) plume addresses multi-scale mass transfer processes in a complex hydrogeologic setting where groundwater and riverwater interact. A series of forefront science questions on mass transfer are posed for research which relate to the effect of spatial heterogeneities; the importance of scale; coupled interactions between biogeochemical, hydrologic, and mass transfer processes; and measurements and approaches needed to characterize and model a mass-transfer dominated system. The project was initiated in February 2007, with CY 2007 and CY 2008 progress summarized in preceding reports. The site has 35 instrumented wells, and an extensive monitoring system. It includes a deep borehole for microbiologic and biogeochemical research that sampled the entire thickness of the unconfined 300 A aquifer. Significant, impactful progress has been made in CY 2009 with completion of extensive laboratory measurements on field sediments, field hydrologic and geophysical characterization, four field experiments, and modeling. The laboratory characterization results are being subjected to geostatistical analyses to develop spatial heterogeneity models of U concentration and chemical, physical, and hydrologic properties needed for reactive transport modeling. The field experiments focused on: (1) physical characterization of the groundwater flow field during a period of stable hydrologic conditions in early spring, (2) comprehensive groundwater monitoring during spring to characterize the release of U(VI) from the lower vadose zone to the aquifer during water table rise and fall, (3) dynamic geophysical monitoring of salt-plume migration during summer, and (4) a U reactive tracer experiment (desorption) during the fall. Geophysical characterization of the well field was completed using the down-well Electrical Resistance Tomography (ERT) array, with results subjected to robust, geostatistically constrained inversion analyses. These measurements along with hydrologic characterization have yielded 3D distributions of hydraulic properties that have been incorporated into an updated and increasingly robust hydrologic model. Based on significant findings from the microbiologic characterization of deep borehole sediments in CY 2008, down-hole biogeochemistry studies were initiated where colonization substrates and spatially discrete water and gas samplers were deployed to select wells. The increasingly comprehensive field experimental results, along with the field and laboratory characterization, are leading to a new conceptual model of U(VI) flow and transport in the IFRC footprint and the 300 Area in general, and insights on the microbiological community and associated biogeochemical processes. A significant issue related to vertical flow in the IFRC wells was identified and evaluated during the spring and fall field experimental campaigns. Both upward and downward flows were observed in response to dynamic Columbia River stage. The vertical flows are caused by the interaction of pressure gradients with our heterogeneous hydraulic conductivity field. These impacts are being evaluated with additional modeling and field activities to facilitate interpretation and mitigation. The project moves into CY 2010 with ambitious plans for a drilling additional wells for the IFRC well field, additional experiments, and modeling. This research is part of the ERSP Hanford IFRC at Pacific Northwest National Laboratory.

  7. Influence of Composition, Helium Generation Rate and Dpa Rate on Neutron-Induced Swelling of Fe-15Cr-16Ni-0.25Ti Alloys in FFTF at {approx} 400 Degrees C

    SciTech Connect (OSTI)

    Okita, T; Wolfer, W G; Sato, T; Sekimura, N; Garner, F A

    2003-08-05

    Contrary to the behavior of swelling of f.c.c. Fe-15Cr-16Ni and Fe-15Cr-16Ni-0.25Ti alloys irradiated together in the same FFTF-MOTA experiment, Fe-15Cr-16Ti-0.25Ti-0.05C does not exhibit a dependence of swelling on dpa rate at {approx}400 C. The transient regime of swelling is prolonged by carbon addition, however. Addition of boron to the carbon-doped alloy decreases the swelling somewhat but does not restore the sensitivity to dpa rate. It appears that the primary influence of boron is chemical in nature, probably associated with boron's impact on the behavior of carbon. Boron's role as a source of helium is thought to be secondary.

  8. Correlation between Pd metal thickness and thermally stable perpendicular magnetic anisotropy features in [Co/Pd]{sub n} multilayers at annealing temperatures up to 500 °C

    SciTech Connect (OSTI)

    An, Gwang Guk; Lee, Ja Bin; Yang, Seung Mo; Yoon, Kap Soo; Kim, Jae Hong; Chung, Woo Seong; Hong, Jin Pyo

    2015-02-15

    We examine highly stable perpendicular magnetic anisotropy (PMA) features of [Co/Pd]{sub 10} multilayers (MLs) versus Pd thickness at various ex-situ annealing temperatures. Thermally stable PMA characteristics were observed up to 500 °C, confirming the suitability of these systems for industrial applications at this temperature. Experimental observations suggest that the choice of equivalent Co and Pd layer thicknesses in a ML configuration ensures thermally stable PMA features, even at higher annealing temperatures. X-ray diffraction patterns and cross-sectional transmission electron microscopy images were obtained to determine thickness, post-annealing PMA behavior, and to explore the structural features that govern these findings.

  9. Experimental Determination of Phase Equilibria in the System H{sub 2}O-CO{sub 2}-NaCl at 0.5 Kb from 500 to 800C

    SciTech Connect (OSTI)

    Anovitz, L.M.

    2001-01-09

    An understanding of activity-composition (a/X) relations and phase equilibria for halite-bearing, mixed-species supercritical fluids is critically important to many geological and industrial applications. The authors have performed experiments on the phase equilibria of H{sub 2}O-CO{sub 2}-NaCl fluids from 500 C to 800 C at 500 bars, conditions of significant importance in studies of magma-hydrothermal systems, geothermal reservoirs and some ore deposits, to obtain highly accurate and precise data for this ternary system. These experiments are conducted using a double capsule technique. An excess of NaCl is placed in an inner Pt capsule, which is crimped shut and placed in an outer capsule containing H{sub 2}O and CO{sub 2}. During the experiment NaCl dissolves out of the inner capsule, and is deposited in the outer capsule during the quench. After the experiment the capsule is opened, and the amount of NaCl remaining in the inner capsule determined by dissolution. The difference between the initial and final amounts of NaCl in the inner capsule yields the solubility of NaCl at the P-T conditions of the experiment. At 500 C data from these experiments suggest that the vapor comer of the three-phase field lies near X(H{sub 2}O) = 0.760, X(NaCl) = 0.065, which is a significantly more water-rich composition than suggested by previous models. As expected, increasing temperature increases the solubility of NaCl in the NaCl-vapor field. For example, at intermediate H{sub 2}O/CO{sub 2} ratios the vapor field extends from approximately near X(H{sub 2}O) = 0.66, X(NaCl) = 0.06 at 500 C to near X(H{sub 2}O) = 0.65, X(NaCl) = 0.08 at 600 C.

  10. Line spectrum and ion temperature measurements from tungsten ions at low ionization stages in large helical device based on vacuum ultraviolet spectroscopy in wavelength range of 500–2200 Å

    SciTech Connect (OSTI)

    Oishi, T. Morita, S.; Goto, M.; Huang, X. L.; Zhang, H. M.

    2014-11-15

    Vacuum ultraviolet spectra of emissions released from tungsten ions at lower ionization stages were measured in the Large Helical Device (LHD) in the wavelength range of 500–2200 Å using a 3 m normal incidence spectrometer. Tungsten ions were distributed in the LHD plasma by injecting a pellet consisting of a small piece of tungsten metal and polyethylene tube. Many lines having different wavelengths from intrinsic impurity ions were observed just after the tungsten pellet injection. Doppler broadening of a tungsten candidate line was successfully measured and the ion temperature was obtained.

  11. Detection of Amorphous Silica in Air-Oxidized Ti3SiC2 at 500-1000°C by NMR and SIMS

    SciTech Connect (OSTI)

    Pang, Wei Kong; Low, I M; Hanna, J V

    2010-11-12

    The use of secondary-ion mass spectrometry (SIMS), nuclear magnetic resonance (NMR) and transmission electron microscopy (TEM) to detect the existence of amorphous silica in Ti3SiC2 oxidised at 500-1000 ºC is described. The formation of an amorphous SiO2 layer and its growth in thickness with temperature was monitored using dynamic SIMS. Results of NMR and TEM verify for the first time the direct evidence of amorphous silica formation during the oxidation of Ti3SiC2 at 1000 ºC.

  12. Ultrasensitive search for long-lived superheavy nuclides in the mass range A=288 to A=300 in natural Pt, Pb, and Bi

    SciTech Connect (OSTI)

    Dellinger, F.; Forstner, O.; Golser, R.; Priller, A.; Steier, P.; Wallner, A.; Winkler, G.; Kutschera, W.

    2011-06-15

    Theoretical models of superheavy elements (SHEs) predict a region of increased stability around the proton and neutron shell closures of Z = 114 and N = 184. Therefore a sensitive search for nuclides in the mass range from A = 288 to A = 300 was performed in natural platinum, lead, and bismuth, covering long-lived isotopes of Eka-Pt (Ds, Z = 110), Eka-Pb (Z = 114), and Eka-Bi (Z = 115). Measurements with accelerator mass spectrometry (AMS) at the Vienna Environmental Research Accelerator (VERA) established upper limits for these SHE isotopes in Pt, Pb, and Bi with abundances of <2x10{sup -15}, <5x10{sup -14}, and <5x10{sup -13}, respectively. These results complement earlier searches for SHEs with AMS at VERA in natural thorium and gold, which now amounts to a total number of 37 SHE nuclides having been explored with AMS. In none of our measurements was evidence found for the existence of SHEs in nature at the reported sensitivity level. Even though a few events were observed in the window for {sup 293}Eka-Bi, a particularly strong pileup background did not allow a definite SHE isotope identification. The present result sets limits on nuclides around the center of the island of stability, essentially ruling out the existence of SHE nuclides with half-lives longer than {approx}150 million years.

  13. Combustion characteristics and NOx emissions of two kinds of swirl burners in a 300-MWe wall-fired pulverized-coal utility boiler

    SciTech Connect (OSTI)

    Li, Z.Q.; Jing, J.P.; Chen, Z.C.; Ren, F.; Xu, B.; Wei, H.D.; Ge, Z.H.

    2008-07-01

    Measurements were performed in a 300-MWe wall-fired pulverized-coal utility boiler. Enhanced ignition-dual register (EI-DR) burners and centrally fuel rich (CFR) swirl coal combustion burners were installed in the bottom row of the furnace during experiments. Local mean concentrations of O{sub 2}, CO, CO{sub 2} and NOx gas species, gas temperatures, and char burnout were determined in the region of the two types of burners. For centrally fuel rich swirl coal combustion burners, local mean CO concentrations, gas temperatures and the temperature gradient are higher and mean concentrations of O{sub 2} and NOx along the jet flow direction in the burner region are lower than for the enhanced ignition-dual register burners. Moreover, the mean O{sub 2} concentration is higher and the gas temperature and mean CO concentration are lower in the side wall region. For centrally fuel rich swirl coal combustion burners in the bottom row, the combustion efficiency of the boiler increases from 96.73% to 97.09%, and NOx emission decreases from 411.5 to 355 ppm at 6% O{sub 2} compared to enhanced ignition-dual register burners and the boiler operates stably at 110 MWe without auxiliary fuel oil.

  14. Columbia Gas of Massachusetts - Residential Energy Efficiency...

    Broader source: Energy.gov (indexed) [DOE]

    Heaters: 400 Tankless Water Heaters: 500 - 800 Condensing Water Heater: 400 Storage Water Heaters: 100 Thermostat: 25 After Market Boiler Reset: 225 Heat Recovery...

  15. AT-400A compliance test report

    SciTech Connect (OSTI)

    Glass, R.E.

    1998-06-01

    In 1993 Sandia was directed to design containers for the long-term storage and transport of nuclear weapons origin fissile material. This program was undertaken at the direction of the US Department of Energy and in cooperation with Lawrence Livermore National Laboratory and Los Alamos National Laboratory. Lawrence Livermore National Laboratory and Los Alamos National Laboratory were tasked with developing the internal fixturing for the contents. The hardware is being supplied by AlliedSignal Federal Manufacturing and Technologies, and the packaging process has been developed at Mason and Hanger Corporation`s Pantex Plant. The unique challenge was to design a container that could be sealed with the fissile material contents; and, anytime during the next 50 years, the container could be transported with only the need for the pre-shipment leak test. This required a rigorous design capable of meeting the long-term storage and transportation requirements. This report addresses the final testing that was undertaken to demonstrate compliance with US radioactive materials transport regulations.

  16. Dielectric breakdown properties of SF{sub 6}-N{sub 2} mixtures at 0.01-1.6 MPa and 300-3000 K

    SciTech Connect (OSTI)

    Zhao Hu; Li Xingwen; Jia Shenli; Murphy, Anthony B.

    2013-04-14

    The dielectric breakdown properties of SF{sub 6}-N{sub 2} mixtures were investigated at different concentrations of N{sub 2}, 0.01-1.6 MPa, and 300-3000 K. The equilibrium compositions of different SF{sub 6}-N{sub 2} mixtures at several gas pressures and temperatures up to 3000 K were first calculated by minimizing the Gibbs free energy under the assumptions of local thermodynamic and chemical equilibrium. The electron energy distribution function was then obtained using the composition data by Boltzmann equation analysis. It was found that adding N{sub 2} to SF{sub 6} gas can markedly reduce the kinetic energy of electrons at relatively high gas temperatures, which enhances the dielectric field strength. Finally, the critical reduced electric field (E/N){sub cr}, defined as the value for which ionization is equal to attachment, of hot SF{sub 6}-N{sub 2} mixtures was determined. The results indicate that in the gas temperature range around 2000-3000 K, increasing the concentration of N{sub 2} effectively enhances the (E/N){sub cr} of SF{sub 6}-N{sub 2} mixtures, and the (E/N){sub cr} of SF{sub 6}-N{sub 2} mixtures at a wide range of concentrations of N{sub 2} (5%, 50%, and 95%) are all higher than that of pure SF{sub 6} gas. Further, this trend exists at all the gas pressures considered (0.01-1.6 MPa).

  17. Combined Estimation of Hydrogeologic Conceptual Model, Parameter, and Scenario Uncertainty with Application to Uranium Transport at the Hanford Site 300 Area

    SciTech Connect (OSTI)

    Meyer, Philip D.; Ye, Ming; Rockhold, Mark L.; Neuman, Shlomo P.; Cantrell, Kirk J.

    2007-07-30

    This report to the Nuclear Regulatory Commission (NRC) describes the development and application of a methodology to systematically and quantitatively assess predictive uncertainty in groundwater flow and transport modeling that considers the combined impact of hydrogeologic uncertainties associated with the conceptual-mathematical basis of a model, model parameters, and the scenario to which the model is applied. The methodology is based on a n extension of a Maximum Likelihood implementation of Bayesian Model Averaging. Model uncertainty is represented by postulating a discrete set of alternative conceptual models for a site with associated prior model probabilities that reflect a belief about the relative plausibility of each model based on its apparent consistency with available knowledge and data. Posterior model probabilities are computed and parameter uncertainty is estimated by calibrating each model to observed system behavior; prior parameter estimates are optionally included. Scenario uncertainty is represented as a discrete set of alternative future conditions affecting boundary conditions, source/sink terms, or other aspects of the models, with associated prior scenario probabilities. A joint assessment of uncertainty results from combining model predictions computed under each scenario using as weight the posterior model and prior scenario probabilities. The uncertainty methodology was applied to modeling of groundwater flow and uranium transport at the Hanford Site 300 Area. Eight alternative models representing uncertainty in the hydrogeologic and geochemical properties as well as the temporal variability were considered. Two scenarios represent alternative future behavior of the Columbia River adjacent to the site were considered. The scenario alternatives were implemented in the models through the boundary conditions. Results demonstrate the feasibility of applying a comprehensive uncertainty assessment to large-scale, detailed groundwater flow and transport modeling and illustrate the benefits of the methodology I providing better estimates of predictive uncertiay8, quantitative results for use in assessing risk, and an improved understanding of the system behavior and the limitations of the models.

  18. THE SLOAN DIGITAL SKY SURVEY STRIPE 82 IMAGING DATA: DEPTH-OPTIMIZED CO-ADDS OVER 300 deg{sup 2} IN FIVE FILTERS

    SciTech Connect (OSTI)

    Jiang, Linhua; Fan, Xiaohui; McGreer, Ian D.; Green, Richard; Bian, Fuyan; Strauss, Michael A.; Buck, Zoë; Annis, James; Hodge, Jacqueline A.; Myers, Adam D.; Rafiee, Alireza; Richards, Gordon

    2014-07-01

    We present and release co-added images of the Sloan Digital Sky Survey (SDSS) Stripe 82. Stripe 82 covers an area of ∼300 deg{sup 2} on the celestial equator, and has been repeatedly scanned 70-90 times in the ugriz bands by the SDSS imaging survey. By making use of all available data in the SDSS archive, our co-added images are optimized for depth. Input single-epoch frames were properly processed and weighted based on seeing, sky transparency, and background noise before co-addition. The resultant products are co-added science images and their associated weight images that record relative weights at individual pixels. The depths of the co-adds, measured as the 5σ detection limits of the aperture (3.''2 diameter) magnitudes for point sources, are roughly 23.9, 25.1, 24.6, 24.1, and 22.8 AB magnitudes in the five bands, respectively. They are 1.9-2.2 mag deeper than the best SDSS single-epoch data. The co-added images have good image quality, with an average point-spread function FWHM of ∼1'' in the r, i, and z bands. We also release object catalogs that were made with SExtractor. These co-added products have many potential uses for studies of galaxies, quasars, and Galactic structure. We further present and release near-IR J-band images that cover ∼90 deg{sup 2} of Stripe 82. These images were obtained using the NEWFIRM camera on the NOAO 4 m Mayall telescope, and have a depth of about 20.0-20.5 Vega magnitudes (also 5σ detection limits for point sources)

  19. Geothermal Data Repository Reaches 500 Submissions | Department...

    Broader source: Energy.gov (indexed) [DOE]

    All projects receiving GTO funding upload their raw data-ranging from well and drilling data to tested exploration methodologies-to the GDR. Ensuring access to the data is not just ...

  20. Microsoft Word - 500_FinalPaper.docx

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    of a "virtual reactor toolkit" that incorporates science-base models, state-of-the-art numerical methods, modern computational science, modern software engineering, and...

  1. Columbia Gas of Massachusetts - Commercial Energy Efficiency...

    Broader source: Energy.gov (indexed) [DOE]

    - 800 Indirect Water Heater: 400 Condensing Stand Alone Water Heaters: 500 Storage Water Heaters: 100 After Market Boiler Reset: 225 Commercial Griddles: 500 Gas Fryers...

  2. Proposed Amendment to Presidential Permit PP-63 and Associated Modifications to 500-kV International Transmission Line: Forbes, Minnesota to Manitoba, Canada, Northern States Power Company. Addendum to the final Environmental Assessment

    SciTech Connect (OSTI)

    Not Available

    1992-10-01

    This Addendum to the Final Environmental Assessment for the Proposed Amendment to Presidential Permit PP-63 and Associated Modifications to 500 kV International Transmission Line: Forbes, Minnesota to Manitoba, Canada (DOE/EA-587) addresses Northern States Power Company`s (NSP) proposed expansion of the Forbes Substation. The applicant has requested that the expansion take place on the west side of the substation, within the existing property line, instead of on the north side as originally proposed. All of the proposed construction would take place on property already owned by NSP. DOE has reviewed the environmental impacts associated with this minor modification and has determined that the conclusions reached in the environmental assessment and Finding of No Significant Impact prepared in connection with NSP`s original amendment request remain valid.

  3. Proposed amendment to presidential permit PP-63 and associated modifications to 500 kV international transmission line, Forbes, Minnesota to Manitoba, Canada. Addendum to the final environmental assessment

    SciTech Connect (OSTI)

    Not Available

    1992-10-01

    This Addendum to the Final Environmental Assessment for the Proposed Amendment to Presidential Permit PP-63 and Associated Modifications to 500 kV International Transmission Line: Forbes, Minnesota to Manitoba, Canada (DOE/EA-587) addresses Northern States Power Company`s (NSP) proposed expansion of the Forbes Substation. The applicant has requested that the expansion take place on the west side of the substation, within the existing property line, instead of on the north side as originally proposed. All of the proposed construction would take place on property already owned by NSP. DOE has reviewed the environmental impacts associated with this minor modification and has determined that the conclusions reached in the environmental assessment and Finding of No Significant Impact prepared in connection with NSP`s original amendment request remain valid.

  4. Measurement of the ?*? distribution of muon pairs with masses between 30 and 500 GeV in 10.4 fb-1 of pp collisions

    SciTech Connect (OSTI)

    Abazov, Victor Mukhamedovich

    2015-04-06

    We present a measurement of the distribution of the variable ?*? for muon pairs with masses between 30 and 500 GeV, using the complete run II data set collected by the D0 detector at the Fermilab Tevatron proton-antiproton collider. This corresponds to an integrated luminosity of 10.4 fb1 at ?s = 1.96 TeV. The data are corrected for detector effects and presented in bins of dimuon rapidity and mass. The variable ?*? probes the same physical effects as the Z/?* boson transverse momentum, but is less susceptible to the effects of experimental resolution and efficiency. These are the first measurements at any collider of the ?*? distributions for dilepton masses away from the Z ? ?+? boson mass peak. As a result, the data are compared to QCD predictions based on the resummation of multiple soft gluons.

  5. Measurement of the {sup 237}Np(n,{gamma}) cross section from 20 meV to 500 keV with a high efficiency, highly segmented 4{pi} BaF{sub 2} detector

    SciTech Connect (OSTI)

    Esch, E.-I.; Bond, E. M.; Bredeweg, T. A.; Couture, A.; Glover, S. E.; Haight, R. C.; Jandel, M.; Kawano, T.; Mertz, A.; O'Donnell, J. M.; Rundberg, R. S.; Schwantes, J. M.; Ullmann, J. L.; Vieira, D. J.; Wilhelmy, J. B.; Wouters, J. M.; Reifarth, R.; Greife, U.; Hatarik, A. M.; Hatarik, R.

    2008-03-15

    The {sup 237}Np(n,{gamma}){sup 238}Np cross section has been measured in the neutron energy range from 20 meV to 500 keV using the DANCE array at the Los Alamos National Laboratory. This new facility allows experiments with submilligram samples and is therefore well suited to investigate isotopes with half-lives as low as a few hundred days. In this benchmark measurement, only 0.42 mg of {sup 237}Np was sufficient to determine differential cross sections relative to the well-known resonance at 0.5 eV. The thermal cross section was measured to {sigma}{sub 2200m/s}=177{+-}5 barn, {sigma}{sub kT=25.3meV}=167{+-}4 barn and the resonance integral to RI=693{+-}6 barn.

  6. Measurement of the Parity-Violating Longitudinal Single-Spin Asymmetry for W{sup {+-}} Boson Production in Polarized Proton-Proton Collisions at {radical}(s)=500 GeV

    SciTech Connect (OSTI)

    Aggarwal, M. M.; Bhati, A. K.; Pruthi, N. K.; Ahammed, Z.; Dong, X.; Grebenyuk, O.; Hjort, E.; Jacobs, P.; Kikola, D. P.; Kiryluk, J.; Klein, S. R.; Masui, H.; Matis, H. S.; Naglis, M.; Odyniec, G.; Olson, D.; Ploskon, M. A.; Poskanzer, A. M.; Powell, C. B.; Ritter, H. G.

    2011-02-11

    We report the first measurement of the parity-violating single-spin asymmetries for midrapidity decay positrons and electrons from W{sup +} and W{sup -} boson production in longitudinally polarized proton-proton collisions at {radical}(s)=500 GeV by the STAR experiment at RHIC. The measured asymmetries, A{sub L}{sup W+}=-0.27{+-}0.10(stat.){+-}0.02(syst.){+-}0.03(norm.) and A{sub L}{sup W-}=0.14{+-}0.19(stat.){+-}0.02(syst.){+-}0.01(norm.), are consistent with theory predictions, which are large and of opposite sign. These predictions are based on polarized quark and antiquark distribution functions constrained by polarized deep-inelastic scattering measurements.

  7. Measurement of the parity-violating longitudinal single-spin asymmetry for W{sup {+-}} boson production in polarized proton-proton collisions at {radical}(s) = 500 GeV

    SciTech Connect (OSTI)

    Igo, G.

    2011-07-15

    We report the first measurement of the parity violating single-spin asymmetries for midrapidity decay positrons and electrons from W{sup +} and W{sup -} boson production in longitudinally polarized proton-proton collisions at {radical}(s) = 500 GeV by the STAR experiment at RHIC. The measured asymmetries, A{sub L}{sup W+} = -0.27{+-}0.10(stat.){+-}0.02(syst.){+-}0.03(norm.) and A{sub L}{sup W-} 0.14{+-}0.19(stat.){+-}0.02(syst.){+-}0.01(norm.), are consistent with theory predictions, which are large and of opposite sign. These predictions are based on polarized quark and antiquark distribution functions constrained by polarized DIS measurements.

  8. Innovative Clean Coal Technology (ICCT): 500 MW demonstration of advanced wall-fired combustion techniques for the reduction of nitrogen oxide (NO{sub x}) emissions from coal-fired boilers. Phase 3B LNB AOFA tests

    SciTech Connect (OSTI)

    Smith, L.L.; Larsen, L.L.

    1993-12-13

    This Innovative Clean Coal Technology II project seeks to evaluate NO{sub x} control techniques on a 500 MW(e) utility boiler. This report is provided to document the testing performed and results achieved during Phase 3B--Low NO{sub x} Burner Retrofit with Advanced Overfire Air (AOFA). This effort began in May 1993 following completion of Phase 3A--Low-NO{sub x} Burner Testing. The primary objective of the Phase 3B test effort was to establish LNB plus AOFA retrofit NO{sub x} emission characteristics under short-term well controlled conditions and under long-term normal system load dispatch conditions. In addition, other important performance data related to the operation of the boiler in this retrofit configuration were documented for comparison to those measured during the Phase 1 baseline test effort. Protocols for data collection and instrumentation operation were established during Phase 1 (see Phase 1 Baseline Tests Report).

  9. Effect on the condition of the metal in A K-300-3.5 turbine owing to multicycle fatigue from participation of a power generating unit in grid frequency and power regulation

    SciTech Connect (OSTI)

    Lebedeva, A. I.; Zorchenko, N. V.; Prudnikov, A. A.

    2011-09-15

    The effect on the condition of the rotor material owing to multicycle fatigue caused by variable stresses during participation of a power generating unit in grid frequency and power regulation is evaluated using the K-300-23.5 steam turbine as an example. It is shown that during normalized primary frequency regulation the safety factor is at least 50, while during automatic secondary regulation of frequency and power there is essentially no damage to the metal.

  10. Guidance on the Use of Hand-Held Survey Meters for radiological Triage: Time-Dependent Detector Count Rates Corresponding to 50, 250, and 500 mSv Effective Dose for Adult Males and Adult Females

    SciTech Connect (OSTI)

    Bolch, W.E.; Hurtado, J.L.; Lee, C.; Manger, Ryan P; Hertel, Nolan; Burgett, E.; Dickerson, W.

    2012-01-01

    In June 2006, the Radiation Studies Branch of the Centers for Disease Control and Prevention held a workshop to explore rapid methods of facilitating radiological triage of large numbers of potentially contaminated individuals following detonation of a radiological dispersal device. Two options were discussed. The first was the use of traditional gamma cameras in nuclear medicine departments operated as makeshift wholebody counters. Guidance on this approach is currently available from the CDC. This approach would be feasible if a manageable number of individuals were involved, transportation to the relevant hospitals was quickly provided, and the medical staff at each facility had been previously trained in this non-traditional use of their radiopharmaceutical imaging devices. If, however, substantially larger numbers of individuals (100 s to 1,000 s) needed radiological screening, other options must be given to first responders, first receivers, and health physicists providing medical management. In this study, the second option of the workshop was investigated by the use of commercially available portable survey meters (either NaI or GM based) for assessing potential ranges of effective dose (G50, 50Y250, 250Y500, and 9500 mSv). Two hybrid computational phantoms were used to model an adult male and an adult female subject internally contaminated with 241Am, 60Cs, 137Cs, 131I, or 192Ir following an acute inhalation or ingestion intake. As a function of time following the exposure, the net count rates corresponding to committed effective doses of 50, 250, and 500 mSv were estimated via Monte Carlo radiation transport simulation for each of four different detector types, positions, and screening distances. Measured net count rates can be compared to these values, and an assignment of one of four possible effective dose ranges could be made. The method implicitly assumes that all external contamination has been removed prior to screening and that the measurements be conducted in a low background, and possibly mobile, facility positioned at the triage location. Net count rate data are provided in both tabular and graphical format within a series of eight handbooks available at the CDC website (http://www.bt.cdc.gov/radiation/clinicians/evaluation).

  11. Integrated Mg/TiO{sub 2}-ionic liquid system for deep desulfurization

    SciTech Connect (OSTI)

    Yin, Yee Cia; Kait, Chong Fai E-mail: hayyiratulfatimah@yahoo.com Fatimah, Hayyiratul E-mail: hayyiratulfatimah@yahoo.com Wilfred, Cecilia E-mail: hayyiratulfatimah@yahoo.com

    2014-10-24

    A series of Mg/TiO{sub 2} photocatalysts were prepared using wet impregnation method followed by calcination at 300, 400 and 500C for 1 h. The photocatalysts were characterized using Thermal Gravimetric Analysis, Fourier-Transform Infrared Spectroscopy, X-Ray Diffraction, and Field Emission Scanning Electron Microscopy. The performance for deep desulfurization was investigated using model oil with 100 ppm sulfur (in the form of dibenzothiophene). The integrated system involves photocatalytic oxidation followed by ionic liquid-extraction processes. The best performing photocatalyst was 0.25wt% Mg loaded on titania calcined at 400C (0.25Mg400), giving 98.5% conversion of dibenzothiophene to dibenzothiophene sulfone. The highest extraction efficiency of 97.8% was displayed by 1,2-diethylimidazolium diethylphosphate. The overall total sulfur removal was 96.3%.

  12. Logs of wells and boreholes drilled during hydrogeologic studies at Lawrence Livermore National Laboratory Site 300, January 1, 1982--June 30, 1988: January 1, 1982 through June 30, 1988

    SciTech Connect (OSTI)

    Toney, K.C.; Crow, N.B.

    1988-01-01

    We present the hydrogeologic well logs for monitor wells and exploratory boreholes drilled at Lawrence Livermore National Laboratory (LLNL) Site 300 between the beginning of environmental investigations in June 1982 and the end of June 1988. These wells and boreholes were drilled as part of studies made to determine the horizontal and vertical distribution of volatile organic compounds (VOCs), high explosive (HE) compounds, and tritium in soil, rock, and ground water at Site 300. The well logs for 293 installations comprise the bulk of this report. We have prepared summaries of Site 300 geology and project history that provide a context for the well logs. Many of the logs in this report have also been published in previous topical reports, but they are nevertheless included in order to make this report a complete record of the wells and boreholes drilled prior to July 1988. A commercially available computer program, LOGGER has been used since late 1985 to generate these logs. This report presents details of the software programs and the hardware used. We are presently completing a project to devise a computer-aided design (CAD) system to produce hydrogeologic cross sections and fence diagrams, utilizing the digitized form of these logs. We find that our system produces publication-quality well and exploratory borehole logs at a lower cost than that of logs drafted by traditional methods.

  13. Measurement of the φ*η distribution of muon pairs with masses between 30 and 500 GeV in 10.4 fb-1 of pp¯ collisions

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Abazov, Victor Mukhamedovich

    2015-04-06

    We present a measurement of the distribution of the variable φ*η for muon pairs with masses between 30 and 500 GeV, using the complete run II data set collected by the D0 detector at the Fermilab Tevatron proton-antiproton collider. This corresponds to an integrated luminosity of 10.4 fb–1 at √s = 1.96 TeV. The data are corrected for detector effects and presented in bins of dimuon rapidity and mass. The variable φ*η probes the same physical effects as the Z/γ* boson transverse momentum, but is less susceptible to the effects of experimental resolution and efficiency. These are the first measurementsmore » at any collider of the φ*η distributions for dilepton masses away from the Z → ℓ+ℓ– boson mass peak. As a result, the data are compared to QCD predictions based on the resummation of multiple soft gluons.« less

  14. Cross Section and Parity Violating Spin Asymmetries of W plus or minus Boson Production in Polarized p+p Collisions at s=500 GeV

    SciTech Connect (OSTI)

    Adare, A.; Awes, Terry C; Cianciolo, Vince; Efremenko, Yuri; Enokizono, Akitomo; Read Jr, Kenneth F; Silvermyr, David O; Sorensen, Soren P; Stankus, Paul W; PHENIX, Collaboration

    2011-01-01

    Large parity-violating longitudinal single-spin asymmetries A{sub L}{sup e+} = -0.86{sub -0.14}{sup +0.30} and A{sub L}{sup e-} = 0.88{sub -0.71}{sup +0.12} are observed for inclusive high transverse momentum electrons and positrons in polarized p+p collisions at a center-of-mass energy of {radical}s = 500 GeV with the PHENIX detector at RHIC. These e{sup {+-}} come mainly from the decay of W{sup {+-}} and Z{sup 0} bosons, and their asymmetries directly demonstrate parity violation in the couplings of the W{sup {+-}} to the light quarks. The observed electron and positron yields were used to estimate W{sup {+-}} boson production cross sections for the e{sup {+-}} channels of {sigma}(pp {yields} W{sup +}X) x BR(W{sup +} {yields} e{sup +}{nu}{sub e}) = 144.1 {+-} 21.2(stat){sub -10.3}{sup +3.4}(syst) {+-} 21.6(norm) pb, and {sigma}(pp {yields} W{sup -}X) x BR(W{sup -} {yields} e{sup -} {bar {nu}}{sub e}) = 31.7 {+-} 12.1(stat){sub -8.2}{sup +10.1}(syst) {+-} 4.8(norm) pb.

  15. Automated setup for magnetic hysteresis characterization based on a voltage controlled current source with 500 kHz full power bandwidth and 10 A peak-to-peak current

    SciTech Connect (OSTI)

    Calabrese, G.; Capineri, L.; Granato, M.; Frattini, G.

    2015-04-15

    This paper describes the design of a system for the characterization of magnetic hysteresis behavior in soft ferrite magnetic cores. The proposed setup can test magnetic materials exciting them with controlled arbitrary magnetic field waveforms, including the capability of providing a DC bias, in a frequency bandwidth up to 500 kHz, with voltages up to 32 V peak-to-peak, and currents up to 10 A peak-to-peak. In order to have an accurate control of the magnetic field waveform, the system is based on a voltage controlled current source. The electronic design is described focusing on closed loop feedback stabilization and passive components choice. The system has real-time hysteretic loop acquisition and visualization. The comparisons between measured hysteresis loops of sample magnetic materials and datasheet available ones are shown. Results showing frequency and thermal behavior of the hysteresis of a test sample prove the system capabilities. Moreover, the B-H loops obtained with a multiple waveforms excitation signal, including DC bias, are reported. The proposal is a low-cost and replicable solution for hysteresis characterization of magnetic materials used in power electronics.

  16. Measurement of the φ*η distribution of muon pairs with masses between 30 and 500 GeV in 10.4 fb-1 of pp¯ collisions

    SciTech Connect (OSTI)

    Abazov, Victor Mukhamedovich

    2015-04-06

    We present a measurement of the distribution of the variable φ*η for muon pairs with masses between 30 and 500 GeV, using the complete run II data set collected by the D0 detector at the Fermilab Tevatron proton-antiproton collider. This corresponds to an integrated luminosity of 10.4 fb–1 at √s = 1.96 TeV. The data are corrected for detector effects and presented in bins of dimuon rapidity and mass. The variable φ*η probes the same physical effects as the Z/γ* boson transverse momentum, but is less susceptible to the effects of experimental resolution and efficiency. These are the first measurements at any collider of the φ*η distributions for dilepton masses away from the Z → ℓ+ boson mass peak. As a result, the data are compared to QCD predictions based on the resummation of multiple soft gluons.

  17. Hot Electron Diagnostic in a Solid Laser Target by Buried K-Shell Fluorer Technique from Ultra-Intense (3x1020W/cm2,< 500 J) Laser-Plasma Interactions on the Petawatt Laser at LLNL

    SciTech Connect (OSTI)

    Yasuike, K.; Key, M.H.; Hatchett, S.P.; Snavely, R.A.

    2000-06-29

    Characterization of hot electron production (a conversion efficiency from laser energy into electrons) in ultra intense laser-solid target interaction, using 1.06 {micro}m laser light with an intensity of up to 3 x 10{sup 20}W cm{sup -2} and an on target laser energy of {le}500 J, has been done by observing K{sub {beta}} as well as K{sub {alpha}} emissions from a buried Mo layer in the targets, which are same structure as in the previous 100 TW experiments but done under less laser intensity and energy conditions ({le} 4 x 10{sup 19} Wcm{sup -2} and {le} 30 J). The conversion efficiency from the laser energy into the energy, carried by hot electrons, has been estimated to be {approx}50%, which are little bit higher than the previous less laser energy ({approx} 20 J) experiments, yet the x-ray emission spectra from the target has change drastically, i.e., gamma flash.

  18. Semi-exclusive structure functions and inclusive form factors for ed{yields}e{sup '}{pi}NN in the energy region from threshold up to 500 MeV

    SciTech Connect (OSTI)

    Darwish, E.M. Al-Thoyaib, S.S.

    2009-08-15

    The separated structure functions R{sub L}, R{sub T}, R{sub LT}, and R{sub TT} governing the semi-exclusive differential cross section for the d(e,e{sup '}{pi})NN reaction are evaluated in the energy region from threshold up to 500 MeV. We present results for both the neutral and the charged pion production channels in a variety of kinematic settings. For the elementary pion electroproduction operator, the realistic unitary isobar MAID-2003 model is used which gives a good description of the process on the free nucleon. The completely inclusive form factors, which determine the inclusive differential cross section when only the scattered electron is detected, are also computed. It has been found that the structure functions and form factors reveal clear differences between the production dynamics for the {pi}{sup 0} and {pi}{sup {+-}} pions. Considerable dependencies of the structure functions and form factors on the pion angle and virtual photon lab-energy are found. The predicted results are found to be insensitive to the potential model used for the deuteron wave function.

  19. Branching ratio measurements of the predissociation of {sup 12}C{sup 16}O by time-slice velocity-map ion imaging in the energy region from 108 000 to 110 500 cm{sup -1}

    SciTech Connect (OSTI)

    Gao Hong; Song Yu; Yang Lei; Shi Xiaoyu; Ng, C. Y.; Jackson, William M.; Yin Qingzhu

    2012-07-21

    Direct branching ratio measurements of the three lowest dissociation channels of {sup 12}C{sup 16}O that produce C({sup 3}P) + O({sup 3}P), C({sup 1}D) + O({sup 3}P), and C({sup 3}P) + O({sup 1}D) are reported in the vacuum ultraviolet region from 108 000 cm{sup -1} (92.59 nm) to 110 500 cm{sup -1} (90.50 nm) using the time-slice velocity-map ion imaging and nonlinear resonant four-wave mixing techniques. Rotationally, resolved carbon ion yield spectra for both {sup 1}{Sigma}{sup +} and {sup 1}{Pi} bands of CO in this region have been obtained. Our measurements using this technique show that the branching ratio in this energy region, especially the relative percentages of the two spin-forbidden channels, is strongly dependent on the particular electronic and vibrational energy levels of CO that are excited.

  20. Design and development of Stirling Engines for stationary power generation applications in the 500 to 3000 hp range. Subtask 1A report: state-of-the-art conceptual design

    SciTech Connect (OSTI)

    1980-03-01

    The first portion of the Conceptual Design Study of Stirling Engines for Stationary Power Application in the 500 to 3000 hp range which was aimed at state-of-the-art stationary Stirling engines for a 1985 hardware demonstration is summarized. The main goals of this effort were to obtain reliable cost data for a stationary Stirling engine capable of meeting future needs for total energy/cogeneration sysems and to establish a pragmatic and conservative base design for a first generation hardware. Starting with an extensive screening effort, 4 engine types, i.e., V-type crank engine, radial engine, swashplate engine, and rhombic drive engine, and 3 heat transport systems, i.e., heat pipe, pressurized gas heat transport loop, and direct gas fired system, were selected. After a preliminary layout cycle, the rhombic drive engine was eliminated due to intolerable maintenance difficulties on the push rod seals. V, radial and swashplate engines were taken through a detailed design/layout cycle, to establish all important design features and reliable engine weights. After comparing engine layouts and analyzing qualitative and quantitative evaluation criteria, the V-crank engine was chosen as the candidate for a 1985 hardware demonstration.