National Library of Energy BETA

Sample records for 400 300 200

  1. EA-1177: Salvage/Demolition of 200 West Area, 200 East Area, and 300 Area Steam Plants, Richland, Washington

    Broader source: Energy.gov [DOE]

    This EA evaluates the environmental impacts for the proposal to salvage and demolish the 200 West Area, 200 East Area, and 300 Area steam plants and their associated steam distribution piping...

  2. Evaluations of University of Wisconsin Silicon Carbide Temperature Monitors 300 LO and 400 LO B

    SciTech Connect (OSTI)

    K. L. Davis; J. L. Rempe; D. L. Knudson; B. M. Chase; T. C. Unruh

    2011-12-01

    Silicon carbide (SiC) temperature monitors 05R4-02-A KG1403 (300 LO) and 05R4-01-A KG1415 (400 LO B) were evaluated at the High Temperature Test Lab (HTTL) to determine their peak irradiation temperatures. HTTL measurements indicate that the peak irradiation temperature for the 300 LO monitor was 295 {+-} 20 C and the peak irradiation temperature for the 400 LO B monitor was 294 {+-} 25 C. Two silicon carbide (SiC) temperature monitors irradiated in the Advanced Test Reactor (ATR) were evaluated at the High Temperature Test Lab (HTTL) to determine their peak temperature during irradiation. These monitors were irradiated as part of the University of Wisconsin Pilot Project with a target dose of 3 dpa. Temperature monitors were fabricated from high density (3.203 g/cm3) SiC manufactured by Rohm Haas with a nominal size of 12.5 mm x 1.0 mm x 0.75 mm (see Attachment A). Table 1 provides identification for each monitor with an expected peak irradiation temperature range based on preliminary thermal analysis (see Attachment B). Post irradiation calculations are planned to reduce uncertainties in these calculated temperatures. Since the early 1960s, SiC has been used as a post-irradiation temperature monitor. As noted in Reference 2, several researchers have observed that neutron irradiation induced lattice expansion of SiC annealed out when the post-irradiation annealing temperature exceeds the peak irradiation temperature. As noted in Reference 3, INL uses resistivity measurements to infer peak irradiation temperature from SiC monitors. Figure 1 depicts the equipment at the HTTL used to evaluate the SiC monitors. The SiC monitors are heated in the annealing furnace using isochronal temperature steps that, depending on customer needs, can range from 50 to 800 C. This furnace is located under a ventilation hood within the stainless steel enclosure. The ventilation system is activated during heating so that any released vapors are vented through this system. Annealing

  3. PDSF Office Hours 10/17/13 from 2:00 to 4:00 pm at LBNL

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    0/17/13 from 2:00 to 4:00 pm at LBNL PDSF Office Hours 10/17/13 from 2:00 to 4:00 pm at LBNL October 7, 2013 I have biweekly office hours on Thursdays at LBNL. The next one is Thursday 10/17/13 from 2:00 - 4:00 pm in the NERSC drop in office at 050A-0143A (in the basement by the bus offices). Please feel free to stop by if you have any questions or want some hands on help with PDSF issues. Subscribe via RSS Subscribe Browse by Date February 2014 January 2014 November 2013 October 2013 September

  4. The Behavior of IAPWS-95 from 250 to 300 K and Pressures up to 400 MPa: Evaluation Based on Recently Derived Property Data

    SciTech Connect (OSTI)

    Wagner, Wolfgang Thol, Monika

    2015-12-15

    Over the past several years, considerable scientific and technical interest has been focused on accurate thermodynamic properties of fluid water covering part of the subcooled (metastable) region and the stable liquid from the melting line up to about 300 K and pressures up to several hundred MPa. Between 2000 and 2010, experimental density data were published whose accuracy was not completely clear. The scientific standard equation of state for fluid water, the IAPWS-95 formulation, was developed on the basis of experimental data for thermodynamic properties that were available by 1995. In this work, it is examined how IAPWS-95 behaves with respect to the experimental data published after 1995. This investigation is carried out for temperatures from 250 to 300 K and pressures up to 400 MPa. The starting point is the assessment of the current data situation. This was mainly performed on the basis of data for the density, expansivity, compressibility, and isobaric heat capacity, which were derived in 2015 from very accurate speed-of-sound data. Apart from experimental data and these derived data, property values calculated from the recently published equation of state for this region of Holten et al. (2014) were also used. As a result, the unclear data situation could be clarified, and uncertainty values could be estimated for the investigated properties. In the region described above, detailed comparisons show that IAPWS-95 is able to represent the latest experimental data for the density, expansivity, compressibility, speed of sound, and isobaric heat capacity to within the uncertainties given in the release on IAPWS-95. Since the release does not contain uncertainty estimates for expansivities and compressibilities, the statement relates to the error propagation of the given uncertainty in density. Due to the lack of experimental data for the isobaric heat capacity for pressures above 100 MPa, no uncertainty estimates are given in the release for this pressure

  5. 300 Area - Hanford Site

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    300 Area 324 Building 325 Building 400 AreaFast Flux Test Facility 618-10 and 618-11 Burial Grounds 700 Area B Plant B Reactor C Reactor Canister Storage Building and Interim ...

  6. 200 Area - Hanford Site

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    300 Area 324 Building 325 Building 400 AreaFast Flux Test Facility 618-10 and 618-11 Burial Grounds 700 Area B Plant B Reactor C Reactor Canister Storage Building and Interim ...

  7. RENEW300: Advancing Renewable Energy at HUD-Assisted Housing...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Minneapolis RENEW300: Advancing Renewable Energy at HUD-Assisted Housing - Minneapolis June 24, 2016 8:00AM to 4:00PM CDT Minneapolis, Minnesota

  8. Oxford System 400

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Oxford Plasmalab System 400 Sputtering System For questions concerning this machines capabilities, please contact Varshni Singh, at 578-0248. ecr.jpg (48456 bytes)  : ecr1.jpg...

  9. Annex D-200 Area Interim Storage Area Final Safety Analysis Report [FSAR] [Section 1 & 2

    SciTech Connect (OSTI)

    CARRELL, R D

    2002-07-16

    The 200 Area Interim Storage Area (200 Area ISA) at the Hanford Site provides for the interim storage of non-defense reactor spent nuclear fuel (SNF) housed in aboveground dry cask storage systems. The 200 Area ISA is a relatively simple facility consisting of a boundary fence with gates, perimeter lighting, and concrete and gravel pads on which to place the dry storage casks. The fence supports safeguards and security and establishes a radiation protection buffer zone. The 200 Area ISA is nominally 200,000 ft{sup 2} and is located west of the Canister Storage Building (CSB). Interim storage at the 200 Area ISA is intended for a period of up to 40 years until the materials are shipped off-site to a disposal facility. This Final Safety Analysis Report (FSAR) does not address removal from storage or shipment from the 200 Area ISA. Three different SNF types contained in three different dry cask storage systems are to be stored at the 200 Area ISA, as follows: (1) Fast Flux Test Facility Fuel--Fifty-three interim storage casks (ISC), each holding a core component container (CCC), will be used to store the Fast Flux Test Facility (FFTF) SNF currently in the 400 Area. (2) Neutron Radiography Facility (NRF) TRIGA'--One Rad-Vault' container will store two DOT-6M3 containers and six NRF TRIGA casks currently stored in the 400 Area. (3) Commercial Light Water Reactor Fuel--Six International Standards Organization (ISO) containers, each holding a NAC-I cask4 with an inner commercial light water reactor (LWR) canister, will be used for commercial LWR SNF from the 300 Area. An aboveground dry cask storage location is necessary for the spent fuel because the current storage facilities are being shut down and deactivated. The spent fuel is being transferred to interim storage because there is no permanent repository storage currently available.

  10. Performance of the TLS Vacuum Systems Operated at 300 mA of Top-up Mode

    SciTech Connect (OSTI)

    Hsiung, G. Y.; Chan, C. K.; Hsueh, H. P.; Yang, T. L.; Chang, C. C.; Hsu, S. N.; Yang, C. Y.; Chen, C. L.; Chen, J. R.

    2007-01-19

    The 1.5 GeV Taiwan Light Source (TLS) has been upgraded, subsequently increasing the beam current from 200 mA to 300 mA. Additionally, the operational mode changed from decay mode to the top-up mode in 2006 after the cavities were replaced by a superconducting RF cavity and the chambers in the injection straight section with new ones in 2005. The operation at 400 mA has been tested to ensure regular operations of a stored beam at 300 mA. Efforts have been made to replace the interlock systems, spare parts, utility systems and signal archiving systems to ensure the reliable operation of the storage ring and ultimately avoid damage incurred to the system. The beam test at a high current and the performance of the vacuum system will be described.

  11. ALSNews Vol. 300

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    0 ALSNews Vol. 300 Print Wednesday, 29 July 2009 00:00 In This Issue Towards Heavy Fermions in Europium Intermetallic Compounds Stochastic Domain-Wall Depinning in Magnetic...

  12. Hanford 300 Area ROD

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    300 Area ROD Briefing to the Hanford Advisory Board March 6, 2014 Larry Gadbois -- EPA Recap of the 300 Area ROD Primary new concept -- Uranium Sequestration: * Purpose: Accelerate restoration of groundwater uranium contamination. * Protect groundwater from downward leaching from the vadose zone (overlying soil). * Add phosphate to chemically bond with uranium into geologically stable autunite. Does not dissolve. * Dissolve phosphate in water, apply at ground surface, inject into the ground,

  13. Phase 1 remedial investigation report for 200-BP-1 operable unit. Volume 1

    SciTech Connect (OSTI)

    Not Available

    1993-09-01

    The US Department of Energy (DOE) Hanford Site, in Washington State is organized into numerically designated operational areas including the 100, 200, 300, 400, 600, and 1100 Areas. The US Environmental Protection Agency (EPA), in November 1989 included the 200 Areas of the Hanford Site on the National Priority List (NPL) under the Comprehensive Environmental Response, Compensation and Liability Act of 1980 (CERCLA). Inclusion on the NPL initiated the remedial investigation (RD process for the 200-BP-1 operable unit. These efforts are being addressed through the Hanford Federal Facility Agreement and Consent Order (Ecology et al. 1989) which was negotiated and approved by the DOE, the EPA, and the State of Washington Department of Ecology (Ecology) in May 1989. This agreement, known as the Tri-Party Agreement, governs all CERCLA efforts at Hanford. In March of 1990, the Department of Energy, Richland Operations (DOE-RL) issued a Remedial Investigation/Feasibility Study (RI/FS) work plan (DOE-RL 1990a) for the 200-BP-1 operable unit. The work plan initiated the first phase of site characterization activities associated with the 200-BP-1 operable unit. The purpose of the 200-BP-1 operable unit RI is to gather and develop the necessary information to adequately understand the risks to human health and the environment posed by the site and to support the development and analysis of remedial alternatives during the FS. The RI analysis will, in turn, be used by Tri-Party Agreement signatories to make a risk-management-based selection of remedies for the releases of hazardous substances that have occurred from the 200-BP-1 operable unit.

  14. 200 Market Building

    High Performance Buildings Database

    Portland, Oregon The 200 Market Building is a high-rise built in 1973 and located in downtown Portland, Oregon. It was purchased in 1988 by its current owner, 200 Market Associates, primarily because of its optimal location in Portland's central business district. Since 1989 the building has undergone continuous improvements in multiple phases.

  15. ALSNews Vol. 300

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Vol. 300 Print In This Issue Towards Heavy Fermions in Europium Intermetallic Compounds Stochastic Domain-Wall Depinning in Magnetic Nanowires ALS Gets $11.3 M in Stimulus Funds for Facility Improvements UEC Corner: Users' Meeting Workshops, Deadlines, and Elections DOE, UC Berkeley, and City of Berkeley Officials Visit Deadline for ALS Doctoral Fellowships Extended to Aug. 14 New Faces: Angel Hernandez Joins User Services Office Introducing: ALS Science Briefs Operations News Links UC Davis

  16. 300-FF-5 Tour

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    -FF-5 Tour SGW-60008-VA, Rev. 0 presented by Patrick Baynes June 14, 2016 2 300-FF-5 Stage A General Location * Uranium sequestration will occur in two sequential stages, Stage A and Stage B. * Infiltration and injection of phosphate solutions into the soil, PRZ, and groundwater will form insoluble minerals that bind mobile uranium. * Stage A was implemented in a 0.75 acre area of high residual uranium contamination. * Stage B will address the remaining 2.25 acres and is still in the planning

  17. Tracker 300 Software

    Energy Science and Technology Software Center (OSTI)

    2006-01-12

    The Tracker300 software is downloaded to an off-the-shelf product called RCM3400/RCM3410 made by Rabbit Semiconductor. The software is a closed loop control which computes the sun's position and provides stability compensation. Using the RCM3400/RCM3410 module, the software stores and retrieves parameters from the onboard flash. The software also allows for communication with a host. It will allow the parameters to be downloaded or uploaded, it will show the status of the controller, it will providemore » real-time feedback, and it will send command acknowledgements. The software will capture the GPS response and ensure the internal clock is set correctly.« less

  18. Status of EXO-200

    SciTech Connect (OSTI)

    Ackerman, Nicole; /SLAC

    2011-12-06

    EXO-200 is the first phase of the Enriched Xenon Observatory (EXO) experiment, which searches for neutrinoless double beta decay in {sup 136}Xe to measure the mass and probe the Majorana nature of the neutrino. EXO-200 consists of 200 kg of liquid Xe enriched to 80% in {sup 136}Xe in an ultra-low background TPC. Energy resolution is enhanced through the simultaneous collection of scintillation light using Large Area Avalanche Photodiodes (LAAPD's) and ionization charge. It is being installed at the WIPP site in New Mexico, which provides a 2000 meter water-equivalent overburden. EXO-200 will begin taking data in 2009, with the expected two-year sensitivity to the half-life for neutrinoless double beta decay of 6.4 x 10{sup 25} years. According to the most recent nuclear matrix element calculations, this corresponds to an effective Majorana neutrino mass of 0.13 to 0.19 eV. It will also measure the two neutrino mode for the first time in {sup 136}Xe.

  19. Form 200 | Open Energy Information

    Open Energy Info (EERE)

    ApplicationPermit Application: Form 200Legal Abstract Form 200: ApplicationReport for Waste Discharge, current through August 14, 2014. Published NA Year Signed or Took Effect...

  20. 200 N. Spring Street

    Office of Legacy Management (LM)

    Dipartment of Energy. ,' Washington,DC20585 ., .\ FEB 1 7 ' 19g5' ,The Honorable Richa,rd. Riordon .', 200 N. Spring Street 'Los Angeles, California ,90012 '~ Dear Mayor Riordon: " Secretary of Energy Hazel O'Leary'has announced a neb approach to openness ins- the Department of Energy (DOE) and its communications with the public. fin support of this initiative, we are pleased~ to forward the enclosed information related to the. former Shannon Luminous Metals site in your jurisdiction that

  1. Microsoft PowerPoint - BSQ-300.pptx

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    BSQ-300 Entire Selection Range BSQ-300 Allowable Selection Range: FER ≥ 1 BSQ-300 Allowable Speed Range: FER BEP ≥ 1 BSQ-300 CY2012 Actual Fan Selections (295) BSQ-300 Selections covered by size 360 BSQ-300 Selections covered by size 420

  2. WIPP Receives 200th Shipment

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    200 th Shipment CARLSBAD, N.M., April 18, 2001 - The U.S. Department of Energy's (DOE) Waste Isolation Pilot Plant (WIPP) today received its 200 th shipment of defense- generated...

  3. CM300DLFinal.doc

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    To reserve a CM300 session, go to wwwncem.lbl.gov, click on "Microscope Scheduling", use proposal number and password to log in. You may only sign up for 2 sessions per month, ...

  4. President Obama Announces $400 Million Conditional Commitment...

    Energy Savers [EERE]

    announced the offer of a conditional commitment for a loan guarantee of 400 million to Abound Solar Manufacturing, LLC to manufacture state-of-the-art thin-film solar panels. ...

  5. Edgestar: ENERGY STAR Referral (DEP400EW)

    Broader source: Energy.gov [DOE]

    DOE referred the matter of Edgestar-brand dehumidifier, model DEP400EW, to the EPA for appropriate action after DOE testing showed that the model does not meet the ENERGY STAR specification.

  6. Welding the AT-400A Containment Vessel

    SciTech Connect (OSTI)

    Brandon, E.

    1998-11-01

    Early in 1994, the Department of Energy assigned Sandia National Laboratories the responsibility for designing and providing the welding system for the girth weld for the AT-400A containment vessel. (The AT-400A container is employed for the shipment and long-term storage of the nuclear weapon pits being returned from the nation's nuclear arsenal.) Mason Hanger Corporation's Pantex Plant was chosen to be the production facility. The project was successfully completed by providing and implementing a turnkey welding system and qualified welding procedure at the Pantex Plant. The welding system was transferred to Pantex and a pilot lot of 20 AT-400A containers with W48 pits was welded in August 1997. This document is intended to bring together the AT-400A welding system and product (girth weld) requirements and the activities conducted to meet those requirements. This document alone is not a complete compilation of the welding development activities but is meant to be a summary to be used with the applicable references.

  7. 300ºC DDS + 300ºC MWD | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    300ºC DDS + 300ºC MWD 300ºC DDS + 300ºC MWD 300ºC DDS + 300ºC MWD presentation at the April 2013 peer review meeting held in Denver, Colorado. schnitger_hughes_peer2013.pdf (807.7 KB) More Documents & Publications High Temperature 300°C Directional Drilling System track 3: enhanced geothermal systems (EGS) | geothermal 2015 peer review Well Monitoring Systems for EGS

  8. 300 Area signal cable study

    SciTech Connect (OSTI)

    Whattam, J.W.

    1994-09-15

    This report was prepared to discuss the alternatives available for removing the 300 Area overhead signal cable system. This system, installed in 1969, has been used for various monitoring and communication signaling needs throughout the 300 Area. Over the years this cabling system has deteriorated, has been continually reconfigured, and has been poorly documented to the point of nonreliability. The first step was to look at the systems utilizing the overhead signal cable that are still required for operation. Of the ten systems that once operated via the signal cable, only five are still required; the civil defense evacuation alarms, the public address (PA) system, the criticality alarms, the Pacific Northwest Laboratory Facilities Management Control System (FMCS), and the 384 annunciator panel. Of these five, the criticality alarms and the FMCS have been dealt with under other proposals. Therefore, this study focused on the alternatives available for the remaining three systems (evacuation alarms, PA system, and 384 panel) plus the accountability aid phones. Once the systems to be discussed were determined, then three alternatives for providing the signaling pathway were examined for each system: (1) re-wire using underground communication ducts, (2) use the Integrated Voice/Data Telecommunications System (IVDTS) already installed and operated by US West, and (3) use radio control. Each alternative was developed with an estimated cost, advantages, and disadvantages. Finally, a recommendation was provided for the best alternative for each system.

  9. OM300 Direction Drilling Module

    DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

    MacGugan, Doug

    2013-08-22

    OM300 – Geothermal Direction Drilling Navigation Tool: Design and produce a prototype directional drilling navigation tool capable of high temperature operation in geothermal drilling Accuracies of 0.1° Inclination and Tool Face, 0.5° Azimuth Environmental Ruggedness typical of existing oil/gas drilling Multiple Selectable Sensor Ranges High accuracy for navigation, low bandwidth High G-range & bandwidth for Stick-Slip and Chirp detection Selectable serial data communications Reduce cost of drilling in high temperature Geothermal reservoirs Innovative aspects of project Honeywell MEMS* Vibrating Beam Accelerometers (VBA) APS Flux-gate Magnetometers Honeywell Silicon-On-Insulator (SOI) High-temperature electronics Rugged High-temperature capable package and assembly process

  10. 200 area TEDF sample schedule

    SciTech Connect (OSTI)

    Brown, M.J.

    1995-03-22

    This document summarizes the sampling criteria associated with the 200 Area Treatment Effluent Facility (TEDF) that are needed to comply with the requirements of the Washington State Discharge Permit No. WA ST 4502 and good engineering practices at the generator streams that feed into TEDF. In addition, this document Identifies the responsible parties for both sampling and data transference.

  11. WAC 173-400 - General Regulations for Air Pollution Sources ...

    Open Energy Info (EERE)

    400 - General Regulations for Air Pollution Sources Jump to: navigation, search OpenEI Reference LibraryAdd to library Legal Document- RegulationRegulation: WAC 173-400 - General...

  12. WAC - 173-400 General Regulations for Air Pollution Sources ...

    Open Energy Info (EERE)

    400 General Regulations for Air Pollution Sources Jump to: navigation, search OpenEI Reference LibraryAdd to library Legal Document- RegulationRegulation: WAC - 173-400 General...

  13. Application for Presidential Permit OE Docket No. PP-400 TDI...

    Broader source: Energy.gov (indexed) [DOE]

    PP-400 TDI-NE - Response Letter from DOD.pdf (52 KB) More Documents & Publications Application for Presidential Permit OE Docket No. PP-400 TDI- NE New England Clean Power Link ...

  14. O:ELECTRICEA-200.PDF

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Order No. EA-200 I. BACKGROUND Exports of electricity from the United States to a foreign country are regulated and require authorization under section 202(e) of the Federal Power Act (FPA) (16 U.S.C. §824a(e)). On December 22, 1998, as supplemented on February 3, 1999, American Electric Power Service Corporation (AEPSC), on behalf of its seven public utility affiliates, collectively known as the "AEP Operating Companies," applied to the Office of Fossil Energy (FE) of the Department

  15. 300 Area Process Trenches Groundwater Monitoring Plan

    SciTech Connect (OSTI)

    Lindberg, Jonathan W.; Chou, Charissa J.

    2001-08-13

    This document is a proposed groundwater monitoring plan for the 300 Area process trenches to comply with RCRA final status, corrective action groundwater monitoring.

  16. Equation of State for Supercooled Water at Pressures up to 400 MPa

    SciTech Connect (OSTI)

    Holten, Vincent; Sengers, Jan V.; Anisimov, Mikhail A.

    2014-12-01

    An equation of state is presented for the thermodynamic properties of cold and supercooled water. It is valid for temperatures from the homogeneous ice nucleation temperature up to 300 K and for pressures up to 400 MPa, and can be extrapolated up to 1000 MPa. The equation of state is compared with experimental data for the density, expansion coefficient, isothermal compressibility, speed of sound, and heat capacity. Estimates for the accuracy of the equation are given. The melting curve of ice I is calculated from the phase-equilibrium condition between the proposed equation and an existing equation of state for ice I.

  17. ESnet, NERSC Blaze 400G Production Network Path

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    ESnet, NERSC Blaze 400G Production Network Path ESnet, NERSC Blaze 400G Production Network Path 400G Link is First Ever by R&E Network November 10, 2015 Contact: Jon Bashor, jbashor@lbl.gov, 510-486-5849 NetworkMapIllustration.png This map shows the 400G production link between Wang Hall at the main LBNL site and the Oakland Scientific Facility. The Department of Energy's Energy Sciences Network (ESnet) and the National Energy Research Scientific Computing Center (NERSC) have built a 400

  18. Hazardous waste operational plan for site 300

    SciTech Connect (OSTI)

    Roberts, R.S.

    1982-02-12

    This plan outlines the procedures and operations used at LLNL's Site 300 for the management of the hazardous waste generated. This waste consists primarily of depleted uranium (a by-product of U-235 enrichment), beryllium, small quantities of analytical chemicals, industrial type waste such as solvents, cleaning acids, photographic chemicals, etc., and explosives. This plan details the operations generating this waste, the proper handling of this material and the procedures used to treat or dispose of the hazardous waste. A considerable amount of information found in this plan was extracted from the Site 300 Safety and Operational Manual written by Site 300 Facility personnel and the Hazards Control Department.

  19. President Obama Announces $400 Million Conditional Commitment Offer to

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Support Solar Panel Manufacturing | Department of Energy 400 Million Conditional Commitment Offer to Support Solar Panel Manufacturing President Obama Announces $400 Million Conditional Commitment Offer to Support Solar Panel Manufacturing July 3, 2010 - 12:00am Addthis Washington D.C. - In his weekly video address, President Obama today announced the offer of a conditional commitment for a loan guarantee of $400 million to Abound Solar Manufacturing, LLC to manufacture state-of-the-art

  20. 300 area TEDF permit compliance monitoring plan

    SciTech Connect (OSTI)

    BERNESKI, L.D.

    1998-11-20

    This document presents the permit compliance monitoring plan for the 300 Area Treated Effluent Disposal Facility (TEDF). It addresses the compliance with the National Pollutant Discharge Elimination System (NPDES) permit and Department of Natural Resources Aquatic Lands Sewer Outfall Lease.

  1. Summary - Building C-400 Thermal Treatment Remedial Design Report...

    Office of Environmental Management (EM)

    C-400 Thermal Treatment 90% Remedial Design Report and Site Investigation, Paducah ... What the ETR Team Recommended The data provide an initial basis for designoperation; ...

  2. Application for Presidential Permit OE Docket No. PP-400 TDI...

    Broader source: Energy.gov (indexed) [DOE]

    Conservation Law Foundation (CLF) provides the following comments and Motion to Intervene regarding the Application by TDI-New England presidential permit. PP-400 TDI-NE - Motion ...

  3. Reno-Moana Area (300) Space Heating Low Temperature Geothermal...

    Open Energy Info (EERE)

    Reno-Moana Area (300) Space Heating Low Temperature Geothermal Facility Jump to: navigation, search Name Reno-Moana Area (300) Space Heating Low Temperature Geothermal Facility...

  4. Conceptual designs for the AT-400MO package

    SciTech Connect (OSTI)

    Fischer, L.E.; Hafner, R.F.; Hovingh, J.; Keeton, S.C.; Russell, E.W.; Lemmings, J.

    1997-01-01

    Currently, Pantex handles and stores weapons pits in AT-400A packages. The Department of Energy currently plans to oversee the conversion of weapon pits into plutonium metal or oxide. These products will then be stored, and perhaps transported at a later time, to other DOE sites. If DOE assigns the pit conversion process to Pantex, it makes sense to store the resulting Pu metal or oxide at Pantex, utilizing existing facilities, equipment, processes, and personnel. The four conceptual designs presented herein substitute the current AT-400A containment vessel, designed for weapon pits, with a vessel designed to store and/or ship Pu metal or oxides. These new designs utilize the existing AT-400A overpack system consisting of the drum assembly and radial impact limiters and likewise employ existing AT-400A production operations.

  5. Obama Administration Announces Additional $20,117,400 for Local...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    ... Funding for state, city, and county governments in the state includes: AR Arkansas Total Sum City, County, and SEO Allocations All 20,117,400 AR Arkansas State Energy Office ...

  6. 400 Area/Fast Flux Test Facility - Hanford Site

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    325 Building 400 AreaFast Flux Test Facility 618-10 ... Test Facility D and DR Reactors Effluent Treatment ... (thermal) liquid-metal (sodium)-cooled nuclear research ...

  7. Application for Presidential Permit OE Docket No. PP-400 TDI...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    NE New England Clean Power Link Project Application for Presidential Permit OE Docket No. PP-400 TDI- NE New England Clean Power Link Project Response to TDI - NE application from ...

  8. Application for Presidential Permit OE Docket No. PP-400 TDI...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    New England - New England Clean Power Link Project Application for Presidential Permit OE Docket No. PP-400 TDI-New England - New England Clean Power Link Project Application from ...

  9. Application for Presidential Permit OE Docket No. PP-400 TDI...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    - New England Clean Power Link Project: Federal Register Notice, Volume 79, No. 131 - July 9, 2014 Application for Presidential Permit OE Docket No. PP-400 TDI-NE - New England ...

  10. Department of Energy Closes $400 Million Loan Guarantee for State...

    Broader source: Energy.gov (indexed) [DOE]

    Steven Chu announced today that a 400 million loan guarantee has been finalized for Abound Solar Manufacturing, LLC to manufacture state-of-the-art thin-film solar panels. ...

  11. ESnet, NERSC Blaze 400G Production Network Path

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    to act as a single 400 Gbps optical transport connection between the two sites. A History of Strong Connections The user facilities known today as NERSC and ESnet both date...

  12. CM200DL-Final.doc

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    To reserve a CM200 session, go to wwwncem.lbl.gov, click on "Microscope Scheduling", use proposal number and password to log in. You may only sign up for one Core session at a ...

  13. Advice and Response 200 - 101 - Hanford Site

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    200 - 101 Hanford Advisory Board Convening Report SSAB Guidance Memorandum of Understanding Membership Nomination and Appointment Process Operating Ground Rules Calendars Advice and Responses Full Board Meeting Information Committee Meeting Information Outgoing Board Correspondence Key Board Products and Special Reports HAB Annual Report HAB and Committee Lists Points of Contact Related Links Advice and Response 200 - 101 Email Email Page | Print Print Page | Text Increase Font Size Decrease

  14. Microsoft PowerPoint - Overview of 200 Areas.pptx

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Hanford's 200 Areas Ken Niles, Assistant Director Oregon Department of Energy Central Plateau Hanford Central Plateau 200 West & East Areas 200 West 200 East 200 West & East Areas 200 West 200 East WTP ERDF US Ecology 200 BC Cribs "Adjacent" Areas Tank Farms 200 West T-TX-TY S-SX-SY U B-BX-BY A-AX-AY-AZ AN-AP-AW C 200 East 18 Tank Farms in 5 Waste Management Areas Tanks Canyons T-Plant B-Plant PUREX U-Plant REDOX Canyons Other Facilities/Waste Streams PFP PUREX Tunnels WESF

  15. 300 Area process trench sediment analysis report

    SciTech Connect (OSTI)

    Zimmerman, M.G.; Kossik, C.D.

    1987-12-01

    This report describes the results of a sampling program for the sediments underlying the Process Trenches serving the 300 Area on the Hanford reservation. These Process Trenches were the subject of a Closure Plan submitted to the Washington State Department of Ecology and to the US Environmental Protection Agency in lieu of a Part B permit application on November 8, 1985. The closure plan described a proposed sampling plan for the underlying sediments and potential remedial actions to be determined by the sample analyses results. The results and proposed remedial action plan are presented and discussed in this report. 50 refs., 6 figs., 8 tabs.

  16. Golden Eagle Territories and Ecology at Site 300

    SciTech Connect (OSTI)

    Fratanduono, M.

    2015-09-29

    Garcia and Associates (GANDA) was contracted by the Lawrence Livermore National Laboratory (LLNL) to collect information on golden eagle (Aquila chrysaetos) use of Site 300. During 2014, we conducted surveys at Site 300 and for an area including a 10-mile radius of Site 300. Those surveys documented 42 golden eagle territories including two territories that overlapped with Site 300. These were named ‘Tesla’ and ‘Linac Road’. In 2015, we conducted surveys to refine the territory boundaries of golden eagle territories that overlapped with Site 300 and to document eagle activity at Site 300.

  17. 200 North Aggregate Area source AAMS report

    SciTech Connect (OSTI)

    Not Available

    1993-06-01

    This report presents the results of an aggregate area management study (AAMS) for the 200 North Aggregate Area in the 200 Areas of the US Department of Energy (DOE) Hanford Site in Washington State. This scoping level study provides the basis for initiating Remedial Investigation/Feasibility Study (RI/FS) activities under the Comprehensive Environmental Response, Compensation, and Liability Act of 1980 (CERCLA) or Resource Conservation and Recovery Act (RCRA) Facility Investigations (RFI) and Corrective Measures Studies (CMS) under RCRA. This report also integrates select RCRA treatment, storage, or disposal (TSD) closure activities with CERCLA and RCRA past practice investigations.

  18. The 300 mA SRF ERL

    SciTech Connect (OSTI)

    Ben-Zvi, Ilan

    2013-11-07

    Energy Recovery Linacs (ERL) are important for a variety of applications, from high-power Free-Electron Lasers (FEL) to polarized-electron polarized-proton colliders. The ERL current is arguably the most important characteristic of ERLs for such applications. With that in mind, the Collider-Accelerator Department at Brookhaven National Laboratory embarked on the development of a 300 mA ERL to serve as an R and D test-bed for high-current ERL technologies. These include high-current, extremely well damped superconducting accelerating cavities, high-current superconducting laser-photocathode electron guns and high quantum-efficiency photocathodes. In this presentation I will cover these ERL related developments.

  19. State Waste Discharge Permit application: 400 Area Septic System

    SciTech Connect (OSTI)

    Not Available

    1994-06-01

    As part of the Hanford Federal Facility Agreement and Consent Order negotiations, the US Department of Energy, Richland Operations Office, the US Environmental Protection Agency, and the Washington State Department of Ecology agreed that liquid effluent discharges to the ground on the Hanford Site which affects groundwater or has the potential to affect groundwater would be subject to permitting under the structure of Chapter 173-216 (or 173-218 where applicable) of the Washington Administrative Code, the State Waste Discharge Permit Program. This document constitutes the State Waste Discharge Permit application for the 400 Area Septic System. The influent to the system is domestic waste water. Although the 400 Area Septic System is not a Public Owned Treatment Works, the Public Owned Treatment Works application is more applicable than the application for industrial waste water. Therefore, the State Waste Discharge Permit application for Public Owned Treatment Works Discharges to Land was used.

  20. The EXO-200 Detector, Part I: Detector Design And Construction...

    Office of Scientific and Technical Information (OSTI)

    Journal Article: The EXO-200 Detector, Part I: Detector Design And Construction Citation Details In-Document Search Title: The EXO-200 Detector, Part I: Detector Design And ...

  1. Report of Waste Discharge application (Form 200) | Open Energy...

    Open Energy Info (EERE)

    Waste Discharge application (Form 200) Jump to: navigation, search OpenEI Reference LibraryAdd to library Form: Report of Waste Discharge application (Form 200) Abstract Persons...

  2. EA-200 American Electric Power Service Corporation | Department...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    200 American Electric Power Service Corporation EA-200 American Electric Power Service Corporation Order authorizing American Electric Power Service Corporation to export electric ...

  3. 2016_stip_attendees_400.jpg | OSTI, US Dept of Energy Office of Scientific

    Office of Scientific and Technical Information (OSTI)

    and Technical Information 2016_stip_attendees_400.jpg

  4. Neutron diffraction measurements of intergranular strains in MONEL-400

    SciTech Connect (OSTI)

    Holden, T.M.; Holt, R.A.; Clarke, A.P.

    1997-12-01

    Measurements have been made of the strain response parallel and perpendicular to an applied stress in uniaxial tensile specimens of MONEL-400. The diffraction elastic constants are in close agreement with the Kroener model. Beyond the yield point, different crystallographic orientations respond quite differently to the applied stress and, upon unloading, residual intergranular strains are generated which are tensile for some orientations and compressive for others. A simple theory based on the Taylor-Bishop-Hill (TBH) model gives a good qualitative description of the effects.

  5. Alloy 400 tube failures by stress corrosion cracking

    SciTech Connect (OSTI)

    Amar, A.S.

    1995-12-01

    A feedwater heater with SB163 Alloy 400 (cold drawn - stress relieved) tubing experienced numerous tube failures and was replaced after of 4.5 years. Failures were attributed to Inter Granular Stress Corrosion Cracking (IGSCC) in the roll transition area. An eddy current test method was developed with EPRI NDE Center technical support to detect the cracks in the tubesheet region. Three tubes were pulled for metallurgical examination. Short axial cracks were found on tube inner surface. Measured crack depths were correlated with the eddy current indications. A large number of tubes were plugged. However, the heater continued to deteriorate rapidly. Potential contributors to IGSCC are discussed.

  6. Alternative Fuels Data Center: Oregon Celebrates 200 Miles of Electric

    Alternative Fuels and Advanced Vehicles Data Center [Office of Energy Efficiency and Renewable Energy (EERE)]

    Highways Oregon Celebrates 200 Miles of Electric Highways to someone by E-mail Share Alternative Fuels Data Center: Oregon Celebrates 200 Miles of Electric Highways on Facebook Tweet about Alternative Fuels Data Center: Oregon Celebrates 200 Miles of Electric Highways on Twitter Bookmark Alternative Fuels Data Center: Oregon Celebrates 200 Miles of Electric Highways on Google Bookmark Alternative Fuels Data Center: Oregon Celebrates 200 Miles of Electric Highways on Delicious Rank

  7. Hanford Site - 300-FF-3 | Department of Energy

    Office of Environmental Management (EM)

    300-FF-3 Hanford Site - 300-FF-3 July 1, 2014 - 12:00pm Addthis US Department of Energy Groundwater Database Groundwater Master Report InstallationName, State: Hanford, WA Responsible DOE Office: Office of Environmental Management Plume Name: 300-FF-3 Remediation Contractor: CHPRC PBS Number: 30 Report Last Updated: July 2014 with CY2013 data Contaminants Halogenated VOCs/SVOCs Present?: Yes VOC Name Concentration (ppb) Regulatory Driver Cleanup Requirement DCE 220 Yes 16 (CUL) TCE 430 Yes 4

  8. Application for presidential permit OE Docket No. PP-300 Maine...

    Energy Savers [EERE]

    0 Maine Public Service Company Application for presidential permit OE Docket No. PP-300 Maine Public Service Company Applicationfrom Maine Public Service Company to construct, ...

  9. Renew 300: Advancing Renewable Energy in Affordable Housing

    Office of Energy Efficiency and Renewable Energy (EERE)

    This program encourages organizations to make public commitments toward the federal renewable energy target of 300 megawatts of onsite or community-scale renewable energy capacity. Organizations...

  10. Characterization of Field Experimental Sites at Hanford's 300...

    Office of Scientific and Technical Information (OSTI)

    Characterization of Field Experimental Sites at Hanford's 300-Area IFC Site Citation Details In-Document Search Title: Characterization of Field Experimental Sites at Hanford's ...

  11. Oregon - ORS 439.300 - Definitions | Open Energy Information

    Open Energy Info (EERE)

    Oregon, 2014 DOI Not Provided Check for DOI availability: http:crossref.org Online Internet link for Oregon - ORS 439.300 - Definitions Citation Oregon. 2014. Oregon - ORS...

  12. Upgrading the Linac 400 MeV Switchyard

    SciTech Connect (OSTI)

    Charles M Ankenbrandt et al.

    2004-06-09

    This note describes changes in the 400 MeV beam transfer system from the Linac to improve the quality of the beam delivered to the Booster and to add the capability to direct beam to the MuCool Test Area (MTA). The new configuration has two pairs of pulsed dipole magnets on each side of the 400 MeV electrostatic Chopper. The smaller pair deflects vertically to replace the kick of the Chopper to send the beam to the Booster while the larger pair deflects horizontally to transfer the beam to the MTA. In this new scheme, the Chopper is uncharged while the beam is injected into the Booster such that the injection position does not rely on Chopper power supply regulation as it does now. A feature of the proposed upgrade is that no changes in the lattice functions are required in the lines to the Booster or to the Dump; once the four new magnets are installed, the switch between the old and new operating modes can be done from upstairs. The transfer to the MTA is already described in a previous note.

  13. FEASIBILITY STUDY REPORT FOR THE 200-ZP-1 GROUNDWATER OPERABLE UNIT

    SciTech Connect (OSTI)

    BYRNES ME

    2008-07-18

    The Hanford Site, managed by the U.S. Department of Energy (DOE), encompasses approximately 1,517 km{sup 2} (586 mi{sup 2}) in the Columbia Basin of south-central Washington State. In 1989, the U.S. Environmental Protection Agency (EPA) placed the 100, 200, 300, and 1100 Areas of the Hanford Site on the 40 Code of Federal Regulations (CFR) 300, 'National Oil and Hazardous Substances Pollution Contingency Plan' National Contingency Plan [NCPD], Appendix B, 'National Priorities List' (NPL), pursuant to the Comprehensive Environmental Response, Compensation, and Liability Act of 1980 (CERCLA). The 200 Areas NPL sites consist of the 200 West and 200 East Areas (Figure 1-1). The 200 Areas contain waste management facilities, inactive irradiated fuel reprocessing facilities, and the 200 North Area (formerly used for interim storage and staging of irradiated fuel). Several waste sites in the 600 Area, located near the 200 Areas, also are included in the 200 Areas NPL site. The 200 Areas NPL site is in a region referred to as the 'Central Plateau' and consists of approximately 700 waste sites, excluding sites assigned to the tank farm waste management areas (WMAs). The 200-ZP-1 Groundwater Operable Unit (OU) consists of the groundwater located under the northern portion of the 200 West Area. Waste sources that contributed to the 200-ZP-1 OU included cribs and trenches that received liquid and/or solid waste in the past from the Z Plant and T Plant aggregate areas, WMA-T, WMA-TX/TY, and the State-Approved Land Disposal Site (SALDS). This feasibility study (FS) for the 200-ZP-1 Groundwater OU was prepared in accordance with the requirements of CERCLA decision documents. These decision documents are part of the Administrative Record for the selection of remedial actions for each waste site and present the selected remedial actions that are chosen in accordance with CERCLA, as amended by the Superfund Amendments and Reauthorization Act of 1986, and to the extent practicable

  14. PEROXIDE DESTRUCTION TESTING FOR THE 200 AREA EFFLUENT TREATMENT FACILITY

    SciTech Connect (OSTI)

    HALGREN DL

    2010-03-12

    The hydrogen peroxide decomposer columns at the 200 Area Effluent Treatment Facility (ETF) have been taken out of service due to ongoing problems with particulate fines and poor destruction performance from the granular activated carbon (GAC) used in the columns. An alternative search was initiated and led to bench scale testing and then pilot scale testing. Based on the bench scale testing three manganese dioxide based catalysts were evaluated in the peroxide destruction pilot column installed at the 300 Area Treated Effluent Disposal Facility. The ten inch diameter, nine foot tall, clear polyvinyl chloride (PVC) column allowed for the same six foot catalyst bed depth as is in the existing ETF system. The flow rate to the column was controlled to evaluate the performance at the same superficial velocity (gpm/ft{sup 2}) as the full scale design flow and normal process flow. Each catalyst was evaluated on peroxide destruction performance and particulate fines capacity and carryover. Peroxide destruction was measured by hydrogen peroxide concentration analysis of samples taken before and after the column. The presence of fines in the column headspace and the discharge from carryover was generally assessed by visual observation. All three catalysts met the peroxide destruction criteria by achieving hydrogen peroxide discharge concentrations of less than 0.5 mg/L at the design flow with inlet peroxide concentrations greater than 100 mg/L. The Sud-Chemie T-2525 catalyst was markedly better in the minimization of fines and particle carryover. It is anticipated the T-2525 can be installed as a direct replacement for the GAC in the peroxide decomposer columns. Based on the results of the peroxide method development work the recommendation is to purchase the T-2525 catalyst and initially load one of the ETF decomposer columns for full scale testing.

  15. Feasibility study of a 200 ampere battery

    SciTech Connect (OSTI)

    Baldwin, A.R.

    1991-06-01

    The results of a Sandia National Laboratories program to design and develop a high-current thermal battery for the Hypersonic Weapons Technology Program are presented. The feasibility of a 200 A, 150 s, 12 Vdc primary battery was demonstrated under ambient conditions. New header feedthrough design concepts were used, and new internal current collectors and internal power leads were considered. The Li(Si)/LiBr-LiCl-LiF/FeS{sub 2} electrochemical system has shown exceptional performance at the high-current operation conditions. A high-rate Zinc/Silver Oxide secondary cell was also evaluated, and the results are presented in this report. These cells exhibited excellent high-rate discharge performance. 5 refs., 19 figs., 8 tabs.

  16. INVESTIGATION IN HARDSURFACING A NICKEL-COPPER ALLOY (MONEL400).

    SciTech Connect (OSTI)

    CZAJKOWSKI,C.; BUTTERS,M.

    2001-12-01

    Brookhaven National Laboratory (BNL) investigated the causes of weldability problems and materials failures encountered with the application of Monel (Ni-Cu) 400 as a base material and Stellite 6 (Co-Cr) as the hard-surfacing material when using the oxyacetylene welding process. This work was performed under a cooperative research and development agreement (CRADA) with the Target Rock Division of the Curtiss-Wright Flow Control Corporation. BNL evaluated two heats of Monel 400 material. One of the heats had performed well during manufacturing, producing an acceptable number of ''good'' parts. The second heat had produced some good parts but also exhibited a peculiar type of hardsurfacing/base metal collapse during the welding process. A review of the chemistry on the two heats of material indicated that they both met the chemical requirements for Monel400. During examination of the failed component, linear indications (cracks) were evident on the valve body, both on the circumferential area (top of valve body) and below the hard surfaced weld deposit. independent measurements also indicated that the two heats met the specification requirement for the material. The heat affected zone (HAZ) also contained linear discontinuities. The valve body was welded using the oxyacetylene welding process, a qualified and skilled welder, and had been given a pre-heat of between 1400-1600 F (760-871 C), which is the Target Rock qualified procedure requirement. Both original suppliers performed mechanical testing on their material that indicated the two heats also met the mechanical property requirements of the specification. The BNL investigation into the cause of the differences between these heats of material utilized the following techniques: (1) Heat Treatment of both heats of material; (2) Hardness testing; (3) Optical microscopy; (4) Scanning electron microscope (SEM)/Fractography; and (5) Energy dispersive spectroscopy (EDS). The report concludes that the cause of the

  17. Identification of 300 Area Contaminants of Potential Concern for Soil

    SciTech Connect (OSTI)

    R.W. Ovink

    2010-04-05

    This report documents the process used to identify source area contaminants of potential concern (COPCs) in support of the 300 Area remedial investigation/feasibility study (RI/FS) work plan. This report also establishes the exclusion criteria applicable for 300 Area use and the analytical methods needed to analyze the COPCs.

  18. Crashworthiness of the AT-400A shipping container

    SciTech Connect (OSTI)

    Gruda, J.D.; York, A.R. II

    1996-05-01

    Shipping containers used for transporting radioactive material must be certified using federal regulations. These regulations require the container be tested or evaluated in severe mechanical and thermal environments which represent hypothetical accident scenarios. The containers are certified if the inner container remains leaktight. This paper presents results from finite element simulations of the accidents which include subjecting the AT-400A (for Pu from dismantled nuclear weapons) to a 30-foot (9 m) drop onto an unyielding target and crushing the container with an 1100 lb (500 kg) steel plate dropped from 30 feet. The nonlinear PRONTO3D finite element results were validated using test results. The simulations of the various impacts and crushes identified trends and worst-case orientations. They also showed that there is a significant margin of safety based on the failure of the containment vessel.

  19. Building C-400 Thermal Treatment 90% Remedial Design Report and Site

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Investigation | Department of Energy Building C-400 Thermal Treatment 90% Remedial Design Report and Site Investigation Building C-400 Thermal Treatment 90% Remedial Design Report and Site Investigation Full Document and Summary Versions are available for download Building C-400 Thermal Treatment 90% Remedial Design Report and Site Investigation (2.17 MB) Summary - Building C-400 Thermal Treatment Remedial Design Report and Investigation, Paducah, Kentucky (57.35 KB) More Documents &

  20. Secretary Chu Announces more than $200 Million for Solar and...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    more than 200 Million for Solar and Water Power Technologies Secretary Chu Announces more than 200 Million for Solar and Water Power Technologies April 22, 2010 - 12:00am Addthis...

  1. Secretary Chu Announces more than $200 Million for Solar and...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    more than 200 Million for Solar and Water Power Technologies Secretary Chu Announces more than 200 Million for Solar and Water Power Technologies April 22, 2010 - 12:00am Addthis ...

  2. File:3-200-71.pdf | Open Energy Information

    Open Energy Info (EERE)

    3-200-71.pdf Jump to: navigation, search File File history File usage File:3-200-71.pdf Size of this preview: 463 599 pixels. Other resolution: 464 600 pixels. Go to page 1 2...

  3. File:3-200-43.pdf | Open Energy Information

    Open Energy Info (EERE)

    3-200-43.pdf Jump to: navigation, search File File history File usage File:3-200-43.pdf Size of this preview: 463 599 pixels. Other resolution: 464 600 pixels. Go to page 1 2...

  4. Revised ground-water monitoring compliance plan for the 300 area process trenches

    SciTech Connect (OSTI)

    Schalla, R.; Aaberg, R.L.; Bates, D.J.; Carlile, J.V.M.; Freshley, M.D.; Liikala, T.L.; Mitchell, P.J.; Olsen, K.B.; Rieger, J.T.

    1988-09-01

    This document contains ground-water monitoring plans for process-water disposal trenches located on the Hanford Site. These trenches, designated the 300 Area Process Trenches, have been used since 1973 for disposal of water that contains small quantities of both chemicals and radionuclides. The ground-water monitoring plans contained herein represent revision and expansion of an effort initiated in June 1985. At that time, a facility-specific monitoring program was implemented at the 300 Area Process Trenches as part of a regulatory compliance effort for hazardous chemicals being conducted on the Hanford Site. This monitoring program was based on the ground-water monitoring requirements for interim-status facilities, which are those facilities that do not yet have final permits, but are authorized to continue interim operations while engaged in the permitting process. The applicable monitoring requirements are described in the Resource Conservation and Recovery Act (RCRA), 40 CFR 265.90 of the federal regulations, and in WAC 173-303-400 of Washington State's regulations (Washington State Department of Ecology 1986). The program implemented for the process trenches was designed to be an alternate program, which is required instead of the standard detection program when a facility is known or suspected to have contaminated the ground water in the uppermost aquifer. The plans for the program, contained in a document prepared by the US Department of Energy (USDOE) in 1985, called for monthly sampling of 14 of the 37 existing monitoring wells at the 300 Area plus the installation and sampling of 2 new wells. 27 refs., 25 figs., 15 tabs.

  5. 200,000 homes weatherized under the Recovery Act

    Broader source: Energy.gov [DOE]

    Today Vice President Biden announced that the Weatherization Assistance Program has weatherized 200,000 homes under the Recovery Act.

  6. Observation of 23 supernovae that exploded <300 pc from Earth during the past 300 kyr

    SciTech Connect (OSTI)

    Firestone, R. B.

    2014-07-01

    Four supernovae (SNe), exploding ≤300 pc from Earth, were recorded 44, 37, 32, and 22 kyr ago in the radiocarbon ({sup 14}C) record during the past 50 kyr. Each SN left a nearly identical signature in the record, beginning with an initial sudden increase in atmospheric radiocarbon, when the SN exploded, followed by a hiatus of 1500 yr, and concluding with a sustained 2000 yr increase in global radiocarbon due to γ-rays produced by diffusive shock in the SN remnant (SNR). For the past 18 kyr excess radiocarbon has decayed with the {sup 14}C half-life. SN22kyrBP, is identified as the Vela SN that exploded 250 ± 30 pc from Earth. These SN are confirmed in the {sup 10}Be, {sup 26}Al, {sup 36}Cl, and NO{sub 3}{sup −} geologic records. The rate of near-Earth SNe is consistent with the observed rate of historical SNe giving a galactic rate of 14 ± 3 kyr{sup –1} assuming the Chandra Galactic Catalog SNR distribution. The Earth has been used as a calorimeter to determine that ≈2 × 10{sup 49} erg were released as γ-rays at the time of each SN explosion and ≈10{sup 50} erg in γ-rays following each SN. The background rate of {sup 14}C production by cosmic rays has been determined as 1.61 atoms cm{sup –2} s{sup –1}. Approximately 1/3 of the cosmic ray energy produced by diffusive shock in the SNR was observed to be emitted as high-energy γ-rays. Analysis of the {sup 10}Be/{sup 9}Be ratio in marine sediment identified 19 additional near-Earth SNe that exploded 50-300 kyr ago. Comparison of the radiocarbon record with global temperature variations indicated that each SN explosion is correlated with a concurrent global warming of ≈3°C-4°C.

  7. State waste discharge permit application: 400 Area secondary cooling water

    SciTech Connect (OSTI)

    Not Available

    1992-12-01

    This document constitutes the Washington Administrative Code 173-216 State Waste Discharge Permit Application that serves as interim compliance as required by the Consent Order DE 91NM-177, for the 400 Area Secondary Cooling Water stream. As part of the Hanford Federal Facility Agreement and Consent Order negotiations, the US Department of Energy, Richland Operations Office, the US Environmental Protection Agency, and the Washington State Department of Ecology agreed that liquid effluent discharges to the ground on the Hanford Site which affect groundwater or have the potential to affect groundwater would be subject to permitting under the structure of Chapter 173-216 (or 173-218 where applicable) of the Washington Administrative Code, the State Waste Discharge Permitting Program. As a result of this decision, the Washington State Department of Ecology and the US Department of Energy, Richland Operations Office entered in to Consent Order DE 91NM-177. The Consent Order DE 91NM-177 requires a series of permitting activities for liquid effluent discharges.

  8. Obama Administration Announces Additional $11,072,300 for Local...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    ... Funding for state, city, and county governments in the state includes: DE Delaware Total Sum City, County, and SEO Allocations All 11,072,300 DE Delaware State Energy Office ...

  9. Obama Administration Announces Additional $10,323,300 for Local...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    ... Funding for state, city, and county governments in the state includes: VT VermontTotal Sum City, County, and SEO Allocations All 10,323,300 VT Vermont State Energy Office ...

  10. 300 Area Remedial Investigation/Feasibility Study and Proposed...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    S. Hudson Page 1 of 2 300 Area Remedial InvestigationFeasibility Study and Proposed Plan Deconstruct Advice Points (paragraph number ) 4-1 The Board believes the Tri-Party...

  11. 300 Area waste acid treatment system closure plan. Revision 1

    SciTech Connect (OSTI)

    1996-03-01

    This section provides a description of the Hanford Site, identifies the proposed method of 300 Area Waste Acid Treatment System (WATS) closure, and briefly summarizes the contents of each chapter of this plan.

  12. Secretary Chu Announces Nearly $300 Million Rebate Program to Encourage

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Purchases of Energy Efficient Appliances | Department of Energy Rebate Program to Encourage Purchases of Energy Efficient Appliances Secretary Chu Announces Nearly $300 Million Rebate Program to Encourage Purchases of Energy Efficient Appliances July 14, 2009 - 12:00am Addthis WASHINGTON, DC - U.S. Department of Energy Secretary Steven Chu today announced the availability of nearly $300 million in funding from the American Recovery and Reinvestment Act for state-run rebate programs for

  13. Deployment of GTHTR300 Cogeneration for Hydrogen and Electric Generation

    SciTech Connect (OSTI)

    Kazuhiko Kunitomi; Xing Yan; Isao Minatsuki

    2004-07-01

    JAERI (Japan Atomic Energy Research Institute) has started the design study on the GTHTR300-cogeneration (GTHTR300C) aiming at producing electricity by a helium gas turbine and hydrogen by a thermochemical water splitting method (IS process method). The GTHTR300C is a block type High Temperature Gas-cooled Reactor (HTGR) with its reactor thermal power of 600 MW and outlet coolant temperature of 950 deg. C. The Intermediate Heat Exchanger (IHX) is located between the reactor pressure vessel (RPV) and the gas turbine system. The heat capacity of the IHX is 170 MW and is used for hydrogen production. The balance of the reactor thermal power is used for electric generation. The GTHTR300C is designed based on existing technologies for the High Temperature Engineering Test Reactor (HTTR) and the helium turbine power conversion technology under development for the Gas Turbine High Temperature Reactor (GTHTR300). This paper describes the deployment of the GTHTR300C together with the original design features and advantages of the system. (authors)

  14. Formation of a laminar electron flow for 300 GHz high-power pulsed gyrotron

    SciTech Connect (OSTI)

    Yamaguchi, Yuusuke; Tatematsu, Yoshinori; Saito, Teruo; Ikeda, Ryosuke; Mudiganti, Jagadish C.; Ogawa, Isamu; Idehara, Toshitaka [Research Center for Development of Far-Infrared Region, University of Fukui, 3-9-1 Bunkyo, Fukui-shi 910-8507 (Japan)

    2012-11-15

    This paper describes the design of a triode magnetron injection gun for use in a 200 kW, 300 GHz gyrotron. As power and frequency increase, the performance of the gyrotron becomes quite sensitive to the quality of the electron beam. Formation of a laminar electron flow is essential for the realization of a high quality beam with a small velocity spread. In this study, a new method is developed for a quantitative evaluation of the laminarity and is applied to optimize the electrode design. The laminarity depends not only on conventional design parameters such as the cathode slant angle but also on the spatial distribution of the electric field along the beam trajectory. In the optimized design, the velocity pitch factors, {alpha}, larger than 1.2 are obtained at 65 kV, 10 A with spreads, {Delta}{alpha}, less than 5%.

  15. A 350 MHz, 200 kW CW, Multiple Beam Inductive Output Tube - Final Report

    SciTech Connect (OSTI)

    R.Lawrece Ives; George Collins; David Marsden Michael Read; Edward Eisen; Takuchi Kamura, Philipp Borchard

    2012-11-28

    This program developed a 200 kW CW, 350 MHz, multiple beam inductive output tube (MBIOT) for driving accelerator cavities. The MBIOT operates at 30 kV with a gain of 23 dB. The estimated efficiency is 70%. The device uses seven electron beams, each transmitting 1.4 A of current. The tube is approximately six feet long and weighs approximately 400 lbs. The prototype device will be evaluated as a potential RF source for the Advanced Photon Source at Argonne National Laboratory (ANL). Because of issues related to delivery of the electron guns, it was not possible to complete assembly and test of the MBIOT during the Phase II program. The device is being completed with support from Calabazas Creek Research, Inc., Communications & Power Industries, LLC. and the Naval Surface Weapons Center (NSWC) in Dahlgren, VA. The MBIOT will be initially tested at NSWC before delivery to ANL. The testing at NSWC is scheduled for February 2013.

  16. U-200: Red Hat Directory Server Information Disclosure Security...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    0: Red Hat Directory Server Information Disclosure Security Issue and Vulnerability U-200: Red Hat Directory Server Information Disclosure Security Issue and Vulnerability June 27,...

  17. EA-200-A American Electric Power Service Corporation | Department...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    -A American Electric Power Service Corporation EA-200-A American Electric Power Service Corporation Order authorizing American Electric Power Service Corporation to export electric ...

  18. Obama Administration Announces Additional $24,624,200 for Local...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Obama Administration Announces Additional 24,624,200 for Local Energy Efficiency ... and energy funding announced by the Administration on March 12th and detailed at ...

  19. Department of Energy Closes $400 Million Loan Guarantee for State of the

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Art Solar Manufacturing in Indiana and Colorado | Department of Energy Closes $400 Million Loan Guarantee for State of the Art Solar Manufacturing in Indiana and Colorado Department of Energy Closes $400 Million Loan Guarantee for State of the Art Solar Manufacturing in Indiana and Colorado December 14, 2010 - 12:00am Addthis Washington D.C. - U.S. Energy Secretary Steven Chu announced today that a $400 million loan guarantee has been finalized for Abound Solar Manufacturing, LLC to

  20. Title 11 Alaska Administrative Code 82.400 - 82.475 Competitive...

    Open Energy Info (EERE)

    Reference LibraryAdd to library Legal Document- RegulationRegulation: Title 11 Alaska Administrative Code 82.400 - 82.475 Competitive BiddingLegal Abstract Implementing...

  1. Hanford 300 Area steam transition preliminary utility options study

    SciTech Connect (OSTI)

    Olson, N.J.; Weakley, S.A.; Berman, M.J.

    1995-06-01

    The cost of steam in the Hanford 300 Area is approaching $60 per million Btu; the cost in industry is {approx} $10 per million Btu. The cost of steam in the 300 Area is expected to continue to increase because of the age of the central steam system, load decreases, safety requirements, and environmental regulations. The intent of this report is to evaluate options that would more cost-effectively met the future heating needs of the buildings in the 300 Area. In general, the options fall into two categories: central systems and distributed systems. A representative option from each category was analyzed using the life-cycle cost analysis (LCCA) techniques mandated by the federal government. The central plant option chosen for evaluation was the existing central steam plant modified to allow continued operation. The distributed option chosen was a dedicated heating system for each building.

  2. 300 Area waste acid treatment system closure plan

    SciTech Connect (OSTI)

    LUKE, S.N.

    1999-05-17

    The Hanford Facility Dangerous Waste Permit Application is considered to be a single application organized into a General Information Portion (document number DOERL-91-28) and a Unit-Specific Portion. The scope of the Unit-Specific Portion includes closure plan documentation submitted for individual, treatment, storage, and/or disposal units undergoing closure, such as the 300 Area Waste Acid Treatment System. Documentation contained in the General Information Portion is broader in nature and could be used by multiple treatment, storage, and/or disposal units (e.g., the glossary provided in the General Information Portion). Whenever appropriate, 300 Area Waste Acid Treatment System documentation makes cross-reference to the General Information Portion, rather than duplicating text. This 300 Area Waste Acid Treatment System Closure Plan (Revision 2) includes a Hanford Facility Dangerous Waste Permit Application, Part A, Form 3. Information provided in this closure plan is current as of April 1999.

  3. Chattanooga Eagle Ford Rio Grande Embayment Texas- Louisiana...

    Gasoline and Diesel Fuel Update (EIA)

    Permian Basin Illinois Basin Anadarko Basin Greater Green River Basin Cherokee Platform ... Shale Gas Plays, Lower 48 States 0 200 400 100 300 Miles Source: Energy Information ...

  4. A 200 MHz 35 MW Multiple Beam Klystron for Accelerator Applications Final Report

    SciTech Connect (OSTI)

    R. Lawrence Ives; Michael Read; Patrick Ferguson; David Marsden

    2011-11-28

    Calabazas Creek Research, Inc. (CCR) performed initial development of a compact and reliable 35 MW, multiple beam klystron (MBK) at 200 MHz with a pulse length of 0.125 ms and a 30 Hz repetition rate. The device was targeted for acceleration and ionization cooling of a muon collider, but there are several other potential applications in this frequency range. The klystron uses multiple beams propagating in individual beam tunnels to reduce space charge and allow reduction in the accelerating voltage. This allows a significant reduction in length over a single beam source. More importantly this allows more efficient and less expensive power supplies. At 200 MHz, the interaction circuit for a single beam klystron would be more than six meters long to obtain 50% efficiency and 50 dB gain. This would require a beam voltage of approximately 400 kV and current of 251 A for a microperveance of 1.0. For an eight beam MBK with the same beam perveance, a three meter long interaction circuit achieves the same power and gain. Each beam operates at 142 kV and 70A. The Phase I demonstrated that this device could be fabricated with funding available in a Phase II program and could achieve the program specifications.

  5. OM300 -GeoThermal MWD Navigation Instrument | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    OM300 -GeoThermal MWD Navigation Instrument OM300 -GeoThermal MWD Navigation Instrument Develop a 300°C capable directional drilling navigation tool using Micro Electro-Mechanical Systems (MEMS) accelerometers and flux-gate magnetometers. high_macgugan_om300.pdf (857.64 KB) More Documents & Publications 300ºC DDS + 300ºC MWD Development of a HT Seismic Tool track 3: enhanced geothermal systems (EGS) | geothermal 2015 peer review

  6. With 400th Ph.D. grad, UW-Madison celebrates a half century of fusion

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    energy | Princeton Plasma Physics Lab With 400th Ph.D. grad, UW-Madison celebrates a half century of fusion energy American Fusion News Category: U.S. Universities Link: With 400th Ph.D. grad, UW-Madison celebrates a half century of fusion energy

  7. 300 area TEDF NPDES Permit Compliance Monitoring Plan

    SciTech Connect (OSTI)

    Loll, C.M.

    1995-09-05

    This document presents the 300 Area Treated Effluent Disposal Facility (TEDF) National Pollutant Discharge Elimination System (NPDES) Permit Compliance Monitoring Plan (MP). The MP describes how ongoing monitoring of the TEDF effluent stream for compliance with the NPDES permit will occur. The MP also includes Quality Assurance protocols to be followed.

  8. Hanford’s 300 Area Sees Dramatic Progress

    Office of Energy Efficiency and Renewable Energy (EERE)

    RICHLAND, Wash. – EM’s Richland Operations Office and its contractor Washington Closure Hanford (WCH) have made tremendous progress in cleaning up areas along the Columbia River at the Hanford Site in the past 10 years. The progress is especially visible in the 300 Area, a former industrial area that covered 1,700 acres at the site’s southern edge.

  9. Updated Conceptual Model for the 300 Area Uranium Groundwater Plume

    SciTech Connect (OSTI)

    Zachara, John M.; Freshley, Mark D.; Last, George V.; Peterson, Robert E.; Bjornstad, Bruce N.

    2012-11-01

    The 300 Area uranium groundwater plume in the 300-FF-5 Operable Unit is residual from past discharge of nuclear fuel fabrication wastes to a number of liquid (and solid) disposal sites. The source zones in the disposal sites were remediated by excavation and backfilled to grade, but sorbed uranium remains in deeper, unexcavated vadose zone sediments. In spite of source term removal, the groundwater plume has shown remarkable persistence, with concentrations exceeding the drinking water standard over an area of approximately 1 km2. The plume resides within a coupled vadose zone, groundwater, river zone system of immense complexity and scale. Interactions between geologic structure, the hydrologic system driven by the Columbia River, groundwater-river exchange points, and the geochemistry of uranium contribute to persistence of the plume. The U.S. Department of Energy (DOE) recently completed a Remedial Investigation/Feasibility Study (RI/FS) to document characterization of the 300 Area uranium plume and plan for beginning to implement proposed remedial actions. As part of the RI/FS document, a conceptual model was developed that integrates knowledge of the hydrogeologic and geochemical properties of the 300 Area and controlling processes to yield an understanding of how the system behaves and the variables that control it. Recent results from the Hanford Integrated Field Research Challenge site and the Subsurface Biogeochemistry Scientific Focus Area Project funded by the DOE Office of Science were used to update the conceptual model and provide an assessment of key factors controlling plume persistence.

  10. Efforts to Develop a 300°C Solder

    SciTech Connect (OSTI)

    Norann, Randy A

    2015-01-25

    This paper covers the efforts made to find a 300°C electrical solder solution for geothermal well monitoring and logging tools by Perma Works LLC. This paper covers: why a high temperature solder is needed, what makes for a good solder, testing flux, testing conductive epoxy and testing intermetallic bonds. Future areas of research are suggested.

  11. Hanford Site - 200-ZP-1 | Department of Energy

    Office of Environmental Management (EM)

    200-ZP-1 Hanford Site - 200-ZP-1 July 1, 2014 - 12:00pm Addthis US Department of Energy Groundwater Database Groundwater Master Report InstallationName, State: Hanford, WA Responsible DOE Office: Office of Environmental Management Plume Name: 200-ZP-1 Remediation Contractor: CHPRC PBS Number: 30 Report Last Updated: July 2014 with CY2013 data Contaminants Halogenated VOCs/SVOCs Present?: Yes VOC Name Concentration (ppb) Regulatory Driver Cleanup Requirement CCI4 2600 Yes 3.4 (CUL) TCE 19 Yes 1

  12. Data Safer than Ever with FM-200 Installation

    Broader source: Energy.gov [DOE]

    The consolidated data center at the Legacy Management Business Center (LMBC) in Morgantown, West Virginia, is now guarded by a state-of-the-art FM-200® Fire Suppression System. Installation of the...

  13. Obama Administration Announces Additional $21,062,200 for Local...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    ... Funding for state, city, and county governments in the state includes: KS Kansas Total Sum City, County, and SEO Allocations All 21,062,200 KS Kansas State Energy Office 9,593,500 ...

  14. Obama Administration Announces Additional $31,449,200 for Local...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    ... Funding for state, city, and county governments in the state includes: SC South CarolinaTotal Sum City, County, and SEO Allocations All 31,449,200 SC South Carolina State Energy ...

  15. Low-noise low-jitter 32-pixels CMOS single-photon avalanche diodes array for single-photon counting from 300 nm to 900 nm

    SciTech Connect (OSTI)

    Scarcella, Carmelo; Tosi, Alberto Villa, Federica; Tisa, Simone; Zappa, Franco

    2013-12-15

    We developed a single-photon counting multichannel detection system, based on a monolithic linear array of 32 CMOS SPADs (Complementary Metal-Oxide-Semiconductor Single-Photon Avalanche Diodes). All channels achieve a timing resolution of 100 ps (full-width at half maximum) and a photon detection efficiency of 50% at 400 nm. Dark count rate is very low even at room temperature, being about 125 counts/s for 50 ?m active area diameter SPADs. Detection performance and microelectronic compactness of this CMOS SPAD array make it the best candidate for ultra-compact time-resolved spectrometers with single-photon sensitivity from 300 nm to 900 nm.

  16. Characterization of Large Area APDs for the EXO-200 Detector

    SciTech Connect (OSTI)

    Neilson, R.; LePort, F.; Pocar, A.; Kumar, K.; Odian, A.; Prescott, C.Y.; Tenev, V.; Ackerman, N.; Akimov, D.; Auger, M.; Benitez-Medina, C.; Breidenbach, M.; Burenkov, A.; Conley, R.; Cook, S.; deVoe, R.; Dolinski, M.J.; Fairbank, W., Jr.; Farine, J.; Fierlinger, P.; Flatt, B.; /Stanford U., Phys. Dept. /Bern U., LHEP /Stanford U., Phys. Dept. /Maryland U. /Colorado State U. /Laurentian U. /Carleton U. /SLAC /Maryland U. /Moscow, ITEP /Alabama U. /SLAC /Colorado State U. /Stanford U., Phys. Dept. /Alabama U. /Stanford U., Phys. Dept. /Alabama U. /SLAC /Carleton U. /SLAC /Maryland U. /Moscow, ITEP /Carleton U. /Stanford U., Phys. Dept. /Bern U., LHEP /SLAC /Laurentian U. /SLAC /Maryland U.

    2011-12-02

    EXO-200 uses 468 large area avalanche photodiodes (LAAPDs) for detection of scintillation light in an ultra-low-background liquid xenon (LXe) detector. We describe initial measurements of dark noise, gain and response to xenon scintillation light of LAAPDs at temperatures from room temperature to 169 K - the temperature of liquid xenon. We also describe the individual characterization of more than 800 LAAPDs for selective installation in the EXO-200 detector.

  17. Hanford Site - 200-BP-5 | Department of Energy

    Office of Environmental Management (EM)

    BP-5 Hanford Site - 200-BP-5 July 1, 2014 - 12:00pm Addthis US Department of Energy Groundwater Database Groundwater Master Report InstallationName, State: Hanford, WA Responsible DOE Office: Office of Environmental Management Plume Name: 200-BP-5 Remediation Contractor: CHPRC PBS Number: 30 Report Last Updated: July 2014 with CY2013 data Contaminants Halogenated VOCs/SVOCs Present?: No Fuel Present? No Metals Present? Yes Isotopes Present? Yes Explosives Present? No Other Contaminants? Yes

  18. Hanford Site - 200-PO-1 | Department of Energy

    Office of Environmental Management (EM)

    PO-1 Hanford Site - 200-PO-1 July 1, 2014 - 12:00pm Addthis US Department of Energy Groundwater Database Groundwater Master Report InstallationName, State: Hanford, WA Responsible DOE Office: Office of Environmental Management Plume Name: 200-PO-1 Remediation Contractor: CHPRC PBS Number: 30 Report Last Updated: July 2014 with CY2013 data Contaminants Halogenated VOCs/SVOCs Present?: No Fuel Present? No Metals Present? Yes Isotopes Present? Yes Explosives Present? No Other Contaminants? No

  19. Supercomputing Challenge draws more than 200 students to Los Alamos

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    National Laboratory Supercomputing Challenge draws more than 200 students Supercomputing Challenge draws more than 200 students to Los Alamos National Laboratory The Challenge is project-based learning geared to teaching a wide range of skills April 16, 2015 Los Alamos National Laboratory sits on top of a once-remote mesa in northern New Mexico with the Jemez mountains as a backdrop to research and innovation covering multi-disciplines from bioscience, sustainable energy sources, to plasma

  20. Latest 200 Area Demolition Offers Snapshot of Hanford Cleanup Progress:

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Recovery Act Funding Allows Demolition of Power Houses Ahead of Schedule | Department of Energy Latest 200 Area Demolition Offers Snapshot of Hanford Cleanup Progress: Recovery Act Funding Allows Demolition of Power Houses Ahead of Schedule Latest 200 Area Demolition Offers Snapshot of Hanford Cleanup Progress: Recovery Act Funding Allows Demolition of Power Houses Ahead of Schedule March 4, 2011 - 12:00pm Addthis Media Contacts Cameron Hardy, DOE (509) 376-5365 Cameron.Hardy@rl.doe.gov

  1. High Temperature 300°C Directional Drilling System

    SciTech Connect (OSTI)

    Chatterjee, Kamalesh; Aaron, Dick; Macpherson, John

    2015-07-31

    Many countries around the world, including the USA, have untapped geothermal energy potential. Enhanced Geothermal Systems (EGS) technology is needed to economically utilize this resource. Temperatures in some EGS reservoirs can exceed 300°C. To effectively utilize EGS resources, an array of injector and production wells must be accurately placed in the formation fracture network. This requires a high temperature directional drilling system. Most commercial services for directional drilling systems are rated for 175°C while geothermal wells require operation at much higher temperatures. Two U.S. Department of Energy (DOE) Geothermal Technologies Program (GTP) projects have been initiated to develop a 300°C capable directional drilling system, the first developing a drill bit, directional motor, and drilling fluid, and the second adding navigation and telemetry systems. This report is for the first project, “High Temperature 300°C Directional Drilling System, including drill bit, directional motor and drilling fluid, for enhanced geothermal systems,” award number DE-EE0002782. The drilling system consists of a drill bit, a directional motor, and drilling fluid. The DOE deliverables are three prototype drilling systems. We have developed three drilling motors; we have developed four roller-cone and five Kymera® bits; and finally, we have developed a 300°C stable drilling fluid, along with a lubricant additive for the metal-to-metal motor. Metal-to-metal directional motors require coatings to the rotor and stator for wear and corrosion resistance, and this coating research has been a significant part of the project. The drill bits performed well in the drill bit simulator test, and the complete drilling system has been tested drilling granite at Baker Hughes’ Experimental Test Facility in Oklahoma. The metal-to-metal motor was additionally subjected to a flow loop test in Baker Hughes’ Celle Technology Center in Germany, where it ran for more than 100

  2. 300 Area TEDF NPDES Permit Compliance Monitoring Plan

    SciTech Connect (OSTI)

    Loll, C.M.

    1994-10-13

    This monitoring plan describes the activities and methods that will be employed at the 300 Area Treated Effluent Disposal Facility (TEDF) in order to ensure compliance with the National Discharge Elimination System (NPDES) permit. Included in this document are a brief description of the project, the specifics of the sampling effort, including the physical location and frequency of sampling, the support required for sampling, and the Quality Assurance (QA) protocols to be followed in the sampling procedures.

  3. Microsoft PowerPoint - 300 Area Perspective.pptx

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Area Perspective 300 Area Perspective River and Plateau Committee February 15, 2012 February 15, 2012 John B. Price Business/Research Park in N Richland h d l h High Density Residential is the norm MSA Bldg and Townhouses "Smartpark" includes Townhouses High Density Residential Infiltration from Impervious Areas & Irrigation Townhouses Grass Townhouse Townhouses Grass Bare Ground from Construction Storm Sewer Asphalt Grass Grate p Remediated 1100 Area -Industrial Area f h l ff

  4. Rebate program brings 16,300 rebates to Sooner State

    Broader source: Energy.gov [DOE]

    Oklahoma's Appliance Rebate Program swept through the plains in May, providing residents a break on upfront appliance costs and ensuring long-term energy savings. Oklahomans claimed more than 16,300 rebates in less than a month on ENERGY STAR refrigerators, clothes washers, single room air conditioners, water heathers, central air conditioners, air-source heat pumps, furnaces and ground-source heat pumps.

  5. DOE's Carbon Utilization and Storage Atlas Estimates at Least 2,400 Billion

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Metric Tons of U.S. CO2 Storage Resource | Department of Energy DOE's Carbon Utilization and Storage Atlas Estimates at Least 2,400 Billion Metric Tons of U.S. CO2 Storage Resource DOE's Carbon Utilization and Storage Atlas Estimates at Least 2,400 Billion Metric Tons of U.S. CO2 Storage Resource December 19, 2012 - 12:00pm Addthis Washington, DC - The United States has at least 2,400 billion metric tons of possible carbon dioxide (CO2) storage resource in saline formations, oil and gas

  6. Recovery Act Weekly Video: 200 Area Asbestos Removal, U-Ancillary Demolition, 200 West Transfer Building Footings

    SciTech Connect (OSTI)

    2010-01-01

    A weekly update of the Recovery Act at work. Demolition of U-Ancillary that was contaminated with uranium and asbestos as well as removing asbestos from the Steam Generation Plant in the 200 East Area.

  7. Recovery Act Weekly Video: 200 Area Asbestos Removal, U-Ancillary Demolition, 200 West Transfer Building Footings

    ScienceCinema (OSTI)

    None

    2012-06-14

    A weekly update of the Recovery Act at work. Demolition of U-Ancillary that was contaminated with uranium and asbestos as well as removing asbestos from the Steam Generation Plant in the 200 East Area.

  8. Application for Presidential Permit PP-400 TDI-NE - New England...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    PP-400 TDI-NE - New England Clean Power Link Project - Motion to Intervene and Comments of the Vermont Department of Public Service - August 6, 2014 Application for Presidential ...

  9. Oil Shale Market is Estimated to Reach USD 7,400.70 Million by...

    Open Energy Info (EERE)

    Oil Shale Market is Estimated to Reach USD 7,400.70 Million by 2022 Home > Groups > Renewable Energy RFPs Wayne31jan's picture Submitted by Wayne31jan(150) Contributor 1 July, 2015...

  10. Summary - Building C-400 Thermal Treatment Remedial Design Report and Investigation, Paducah, Kentucky

    Office of Environmental Management (EM)

    Paducah, KY EM Project: Building C400 Thermal Treatment ETR Report Date: August 2007 ETR-8 United States Department of Energy Office of Environmental Management (DOE-EM) External Technical Review of Building C-400 Thermal Treatment 90% Remedial Design Report and Site Investigation, Paducah Kentucky Why DOE-EM Did This Review The groundwater underlying the Paducah Gaseous Diffusion Plant (PGDP) is contaminated by chlorinated solvents, principally trichloroethylene (TCE), as well as other

  11. Obama Administration Announces Additional $102,508,400 for Local Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Efficiency Improvements in Pennsylvania | Department of Energy 02,508,400 for Local Energy Efficiency Improvements in Pennsylvania Obama Administration Announces Additional $102,508,400 for Local Energy Efficiency Improvements in Pennsylvania March 26, 2009 - 12:00am Addthis WASHINGTON - Vice President Joe Biden and Energy Secretary Steven Chu today announced plans to invest $3.2 billion in energy efficiency and conservation projects in U.S. cities, counties, states, territories, and Native

  12. Obama Administration Announces Additional $63,817,400 for Local Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Efficiency Improvements in Arizona | Department of Energy 63,817,400 for Local Energy Efficiency Improvements in Arizona Obama Administration Announces Additional $63,817,400 for Local Energy Efficiency Improvements in Arizona March 26, 2009 - 12:00am Addthis WASHINGTON - Vice President Joe Biden and Energy Secretary Steven Chu today announced plans to invest $3.2 billion in energy efficiency and conservation projects in U.S. cities, counties, states, territories, and Native American tribes.

  13. Meteorological Observations for Renewable Energy Applications at Site 300

    SciTech Connect (OSTI)

    Wharton, S; Alai, M; Myers, K

    2011-10-26

    In early October 2010, two Laser and Detection Ranging (LIDAR) units (LIDAR-96 and LIDAR-97), a 3 m tall flux tower, and a 3 m tall meteorological tower were installed in the northern section of Site 300 (Figure 1) as a first step in development of a renewable energy testbed facility. This section of the SMS project is aimed at supporting that effort with continuous maintenance of atmospheric monitoring instruments capable of measuring vertical profiles of wind speed and wind direction at heights encountered by future wind power turbines. In addition, fluxes of energy are monitored to estimate atmospheric mixing and its effects on wind flow properties at turbine rotor disk heights. Together, these measurements are critical for providing an accurate wind resource characterization and for validating LLNL atmospheric prediction codes for future renewable energy projects at Site 300. Accurate, high-resolution meteorological measurements of wind flow in the planetary boundary layer (PBL) and surface-atmosphere energy exchange are required for understanding the properties and quality of available wind power at Site 300. Wind speeds at heights found in a typical wind turbine rotor disk ({approx} 40-140 m) are driven by the synergistic impacts of atmospheric stability, orography, and land-surface characteristics on the mean wind flow in the PBL and related turbulence structures. This section of the report details the maintenance and labor required in FY11 to optimize the meteorological instruments and ensure high accuracy of their measurements. A detailed look at the observations from FY11 is also presented. This portion of the project met the following milestones: Milestone 1: successful maintenance and data collection of LIDAR and flux tower instruments; Milestone 2: successful installation of solar power for the LIDAR units; and Milestone 3: successful implementation of remote data transmission for the LIDAR units.

  14. 200-Area plateau inactive miscellaneous underground storage tanks locations

    SciTech Connect (OSTI)

    Brevick, C.H.

    1997-12-01

    Fluor Daniel Northwest (FDNW) has been tasked by Lockheed Martin Hanford Corporation (LMHC) to incorporate current location data for 64 of the 200-Area plateau inactive miscellaneous underground storage tanks (IMUST) into the centralized mapping computer database for the Hanford facilities. The IMUST coordinate locations and tank names for the tanks currently assigned to the Hanford Site contractors are listed in Appendix A. The IMUST are inactive tanks installed in underground vaults or buried directly in the ground within the 200-East and 200-West Areas of the Hanford Site. The tanks are categorized as tanks with a capacity of less than 190,000 liters (50,000 gal). Some of the IMUST have been stabilized, pumped dry, filled with grout, or may contain an inventory or radioactive and/or hazardous materials. The IMUST have been out of service for at least 12 years.

  15. Metrology issues for processing of 300 mm wafers

    SciTech Connect (OSTI)

    Watanabe, Kenji; Koike, Atsuyoshi

    1998-11-24

    Construction of IC lines using 300 mm wafers will begin in 1998-99 for pilot lines, with construction of mass production lines in 2000 or later. These lines will most likely be introduced with design rules in the range from 250 to 180 nm. Difficult challenges for these feature sizes include critical dimensions, registration, thin film measurement, and defect inspection. At the same time, metrology is expected to play a major role in controlling costs, increasing manufacturing flexibility, and decreasing cycle time in addition to assisting in the reduced emission of global warming gases.

  16. Developing a 300C Analog Tool for EGS

    SciTech Connect (OSTI)

    Normann, Randy

    2015-03-23

    This paper covers the development of a 300°C geothermal well monitoring tool for supporting future EGS (enhanced geothermal systems) power production. This is the first of 3 tools planed. This is an analog tool designed for monitoring well pressure and temperature. There is discussion on 3 different circuit topologies and the development of the supporting surface electronics and software. There is information on testing electronic circuits and component. One of the major components is the cable used to connect the analog tool to the surface.

  17. Innovative Cell Materials and Designs for 300 Mile Range EVs

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Innovative Cell Materials and Design for 300 Mile Range EVs Yimin Zhu, PD/PI OneD Material, LLC (former Nanosys Energy Storage) Palo Alto, California June 16 ~20, 2014 DOE Vehicle Technologies AMR 2014 ES130_zhu_2014_p This presentation does not contain any proprietary, confidential, or otherwise restricted information TM * Barriers addressed - Performance: Low Wh/kg & Wh/L - Life: Poor deep discharge cycles - Cost: High $/kWh * Targets Anode: >700 mAh/g 1,600 mAh/g >800 cycles

  18. Hanford Site - 200-UP-1 | Department of Energy

    Office of Environmental Management (EM)

    UP-1 Hanford Site - 200-UP-1 July 1, 2014 - 12:00pm Addthis US Department of Energy Groundwater Database Groundwater Master Report InstallationName, State: Hanford, WA Responsible DOE Office: Office of Environmental Management Plume Name: 200-UP-1 Remediation Contractor: CHPRC PBS Number: 30 Report Last Updated: July 2014 with CY2013 data Contaminants Halogenated VOCs/SVOCs Present?: Yes VOC Name Concentration (ppb) Regulatory Driver Cleanup Requirement CCI4 700 Yes 3.4 (RAO) TCE 7.2 Yes 5 (DWS)

  19. O:\ELECTRIC\ORDERS\EA-200-a.PDF

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Order No. EA-200-A I. BACKGROUND Exports of electricity from the United States to a foreign country are regulated and require authorization under section 202(e) of the Federal Power Act (FPA) (16 U.S.C. §824a(e)). On April 6, 1999, in Order No. EA-200, the Office of Fossil Energy (FE) of the Department of Energy (DOE) authorized five of the public utility affiliates of American Electric Power Service Corporation (AEPSC) to transmit electric energy from the United States to Canada. The entities

  20. 200 Area Liquid Effluent Facilities -- Quality assurance program plan

    SciTech Connect (OSTI)

    Fernandez, L.

    1995-03-13

    This Quality Assurance Program Plan (QAPP) describes the quality assurance and management controls used by the 200 Area Liquid Effluent Facilities (LEF) to perform its activities in accordance with DOE Order 5700.6C. The 200 Area LEF consists of the following facilities: Effluent Treatment Facility (ETF); Treated Effluent Disposal Facility (TEDF); Liquid Effluent Retention facility (LERF); and Truck Loading Facility -- (Project W291). The intent is to ensure that all activities such as collection of effluents, treatment, concentration of secondary wastes, verification, sampling and disposal of treated effluents and solids related with the LEF operations, conform to established requirements.

  1. Low-field magnetoresistance up to 400 K in double perovskite Sr{sub 2}FeMoO{sub 6} synthesized by a citrate route

    SciTech Connect (OSTI)

    Harnagea, L.; Jurca, B.; Berthet, P.

    2014-03-15

    A wet-chemistry technique, namely the citrate route, has been used to prepare high-quality polycrystalline samples of double perovskite Sr{sub 2}FeMoO{sub 6}. We report on the evolution of magnetic and magnetoresistive properties of the synthesized samples as a function of three parameters (i) the pH of the starting solution, (ii) the decomposition temperature of the citrate precursors and (iii) the sintering conditions. The low-field magnetoresistance (LFMR) value of our best samples is as high as 5% at room temperature for an applied magnetic field of 1 kOe. Additionally, the distinguishing feature of these samples is the persistence of LFMR, with a reasonably large value, up to 400 K which is a crucial parameter for any practical application. Our study indicates that the enhancement of LFMR observed is due to a good compromise between the grain size distribution and their magnetic polarization. -- Graphical abstract: The microstructure (left panel) and corresponding low-field magnetoresistance of one of the Sr{sub 2}FeMoO{sub 6} samples synthesized in the course of this work. Highlights: Samples of Sr{sub 2}FeMoO{sub 6} are prepared using a citrate route under varying conditions. Magnetoresistive properties are improved and optimized. Low-field magnetoresitence values as large as 5% at 300 K/1 kOe are reported. Persistence of low-field magnetoresistance up to 400 K.

  2. Intermetallic phase formation and breakdown of Mo diffusion barriers in Ni-Mo-Cu and Ni-Mo-Monel 400 diffusion triads

    SciTech Connect (OSTI)

    Shueh, Y.

    1988-01-01

    The purpose of this research was to study the kinetics of compound formation and the interdiffusion behavior of a sacrificial type diffusion barrier in a model system. Ni-Mo diffusion couples were annealed in an inert atmosphere at 950-1050{degree}C for 5-300 hours. Ni-Mo-Cu and Ni-Mo-Monel 400 diffusion triads with varied thicknesses of Mo layers sandwiched by Ni and C or Monel 400 disks were annealed under the same conditions. Parabolic growth of the intermetallic phase, {beta}, was observed at 1000{degree}C and 1050{degree}C in the semi-infinite Ni-Mo diffusion couple an din the Ni-Mo-Cu diffusion triad when a finite thickness of the Mo layer remained. The {beta} phase exhibited more or less planar morphology except in the case of some extremely rugged interfaces which were associated with grain boundaries adjacent to these interfaces. Dissociation and recession of the compound layer in Ni-Mo-Cu diffusion triads initiated when the Mo layer was nearly consumed. The product phases of the dissociation reaction are consistent with those predicted from the Ni-Mo-Cu ternary phase diagram. Numerical methods based on a finite difference technique, and an analytical solution based on diffusion controlled parabolic growth and quasi-steady-state approximation in the {beta} phase region were used to analyze the results.

  3. 300 Area Uranium Stabilization Through Polyphosphate Injection: Final Report

    SciTech Connect (OSTI)

    Vermeul, Vincent R.; Bjornstad, Bruce N.; Fritz, Brad G.; Fruchter, Jonathan S.; Mackley, Rob D.; Newcomer, Darrell R.; Mendoza, Donaldo P.; Rockhold, Mark L.; Wellman, Dawn M.; Williams, Mark D.

    2009-06-30

    The objective of the treatability test was to evaluate the efficacy of using polyphosphate injections to treat uranium-contaminated groundwater in situ. A test site consisting of an injection well and 15 monitoring wells was installed in the 300 Area near the process trenches that had previously received uranium-bearing effluents. This report summarizes the work on the polyphosphate injection project, including bench-scale laboratory studies, a field injection test, and the subsequent analysis and interpretation of the results. Previous laboratory tests have demonstrated that when a soluble form of polyphosphate is injected into uranium-bearing saturated porous media, immobilization of uranium occurs due to formation of an insoluble uranyl phosphate, autunite [Ca(UO2)2(PO4)2•nH2O]. These tests were conducted at conditions expected for the aquifer and used Hanford soils and groundwater containing very low concentrations of uranium (10-6 M). Because autunite sequesters uranium in the oxidized form U(VI) rather than forcing reduction to U(IV), the possibility of re-oxidation and subsequent re-mobilization is negated. Extensive testing demonstrated the very low solubility and slow dissolution kinetics of autunite. In addition to autunite, excess phosphorous may result in apatite mineral formation, which provides a long-term source of treatment capacity. Phosphate arrival response data indicate that, under site conditions, the polyphosphate amendment could be effectively distributed over a relatively large lateral extent, with wells located at a radial distance of 23 m (75 ft) reaching from between 40% and 60% of the injection concentration. Given these phosphate transport characteristics, direct treatment of uranium through the formation of uranyl-phosphate mineral phases (i.e., autunite) could likely be effectively implemented at full field scale. However, formation of calcium-phosphate mineral phases using the selected three-phase approach was problematic. Although

  4. EOS & damage behavior of S200-F Be

    SciTech Connect (OSTI)

    Adams, Chris D; Anderson, William W

    2011-01-24

    We have performed a series of plate impact experiments on both vacuum hot-pressed and Roll-textured S-200F Be on the 40 mm gun at TA-55. This presentation provides an update of the progress to date for this effort.

  5. 200,000 homes weatherized under the Recovery Act

    ScienceCinema (OSTI)

    Zoi, Cathy

    2013-05-29

    Today Vice President Biden announced that the Weatherization Assistance Program has weatherized 200,000 homes under the Recovery Act. We're taking your questions and comments right now on weatherization. Join in the conversation! *Facebook -- http://www.facebook.com/energygov *Twitter -- http://www.twitter.com/energy

  6. 200 Area Deactivation Project Facilities Authorization Envelope Document

    SciTech Connect (OSTI)

    DODD, E.N.

    2000-03-28

    Project facilities as required by HNF-PRO-2701, Authorization Envelope and Authorization Agreement. The Authorization Agreements (AA's) do not identify the specific set of environmental safety and health requirements that are applicable to the facility. Therefore, the facility Authorization Envelopes are defined here to identify the applicable requirements. This document identifies the authorization envelopes for the 200 Area Deactivation.

  7. Feasibility study report for the 200-BP-1 operable unit

    SciTech Connect (OSTI)

    Not Available

    1993-06-01

    This feasibility study examines a range of alternatives and provides recommendations for selecting a preferred alternative for remediating contamination at the 200-BP-1 operable unit. The 200-BP-1 operable unit is located in the center of the Hanford Site along the northern boundary of the 200 East Area. The 241-BY Tank Farm is located immediately to the south of the operable unit. 200-BP-1 is a source operable unit with contaminated soils associated primarily with nine inactive cribs (known as the 216-B cribs). These cribs were used for disposal of low-level radioactive liquid waste from U Plant uranium recovery operations, and waste storage tank condensate from the adjacent 241-BY Tank Farm. The cribs used for disposal of U Plant waste were in operation from 1955--1965, and the cribs used for disposal of tank condensate were in operation from 1965--1975. In addition to the cribs, four unplanned releases of radioactive materials have occurred within the operable unit. Contaminated surface soils associated with the unplanned releases have been consolidated over the cribs and covered with clean soil to reduce contaminant migration and exposure. Discharge of wastes to the cribs has resulted in soil and groundwater contamination. The groundwater is being addressed as part of the 200 East Aggregate Area, groundwater operable unit. Contaminated soils at the site can be categorized by the types of contaminants, their distribution in the soil column, and the risk posed by the various potential exposure pathways. Below the clean soil cover, the near surface soils contain low-levels of contamination with cesium-137, radium-226, strontium-90, thorium-228, and uranium. The lifetime incremental cancer risk associated with these soils if they were exposed at the surface is 9{times}10{sup {minus}5}.

  8. Delisting petition for 300-M saltstone (treated F006 sludge) from the 300-M liquid effluent treatment facility

    SciTech Connect (OSTI)

    Not Available

    1989-04-04

    This petition seeks exclusion for stabilized and solidified sludge material generated by treatment of wastewater from the 300-M aluminum forming and metal finishing processes. The waste contains both hazardous and radioactive components and is classified as a mixed waste. The objective of this petition is to demonstrate that the stabilized sludge material (saltstone), when properly disposed, will not exceed the health-based standards for the hazardous constituents. This petition contains sampling and analytical data which justify the request for exclusion. The results show that when the data are applied to the EPA Vertical and Horizontal Spread (VHS) Model, health-based standards for all hazardous waste constituents will not be exceeded during worst case operating and environmental conditions. Disposal of the stabilized sludge material in concrete vaults will meet the requirements pertaining to Waste Management Activities for Groundwater Protection at the Savannah River Site in Aiken, S.C. Documents set forth performance objectives and disposal options for low-level radioactive waste disposal. Concrete vaults specified for disposal of 300-M saltstone (treated F006 sludge) assure that these performance objectives will be met.

  9. Solar and Energy Loan Fund Receives $300,000 Community Reinvestment...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Solar and Energy Loan Fund Receives 300,000 Community Reinvestment Act Loan to Invest in Home Energy Upgrades Solar and Energy Loan Fund Receives 300,000 Community Reinvestment ...

  10. Department of Energy Awards $300,000 to Tri-City Industrial Developmen...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    300,000 to Tri-City Industrial Development Council in Washington State Department of Energy Awards 300,000 to Tri-City Industrial Development Council in Washington State ...

  11. Technical evaluation: 300 Area steam line valve accident

    SciTech Connect (OSTI)

    Not Available

    1993-08-01

    On June 7, 1993, a journeyman power operator (JPO) was severely burned and later died as a result of the failure of a 6-in. valve that occurred when he attempted to open main steam supply (MSS) valve MSS-25 in the U-3 valve pit. The pit is located northwest of Building 331 in the 300 Area of the Hanford Site. Figure 1-1 shows a layout of the 300 Area steam piping system including the U-3 steam valve pit. Figure 1-2 shows a cutaway view of the approximately 10- by 13- by 16-ft-high valve pit with its various steam valves and connecting piping. Valve MSS-25, an 8-in. valve, is located at the bottom of the pit. The failed 6-in. valve was located at the top of the pit where it branched from the upper portion of the 8-in. line at the 8- by 8- by 6-in. tee and was then ``blanked off`` with a blind flange. The purpose of this technical evaluation was to determine the cause of the accident that led to the failure of the 6-in. valve. The probable cause for the 6-in. valve failure was determined by visual, nondestructive, and destructive examination of the failed valve and by metallurgical analysis of the fractured region of the valve. The cause of the accident was ultimately identified by correlating the observed failure mode to the most probable physical phenomenon. Thermal-hydraulic analyses, component stress analyses, and tests were performed to verify that the probable physical phenomenon could be reasonably expected to produce the failure in the valve that was observed.

  12. Westinghouse Offers $6,400 in College Scholarships to Eddy County Students

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Offers $6,400 in College Scholarships to Eddy County Students CARLSBAD, N.M., February 18, 2000 - The Westinghouse Government Services Group today announced that $6,400 in college scholarships will be awarded to Eddy County students for the 2000-2001 school year. The deadline to apply is April 3. Two $2,500 scholarships are being offered - one will be honored at New Mexico State University (NMSU) in Las Cruces, and one at the College of the Southwest (CSW) in Carlsbad. High school seniors

  13. PVMRW2013 Wed., Feb. 27, 3:00 Final Discussion | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    3:00 Final Discussion PVMRW2013 Wed., Feb. 27, 3:00 Final Discussion The final discussion reviewed many of the complex topics covered during the two days... discussionnotes_weds_300.pdf (103.52 KB) More Documents & Publications PVMRW2013 Wed., Feb. 27, 1:45 Discussion notes PVMRW2013 Wed., Feb. 27, 10:00 Discussion notes:

  14. 150K - 200K miniature pulse tube cooler for micro satellites

    SciTech Connect (OSTI)

    Chassaing, Clément; Butterworth, James; Aigouy, Gérald; Daniel, Christophe; Crespin, Maurice; Duvivier, Eric

    2014-01-29

    Air Liquide is working with the CNES and Steel électronique in 2013 to design, manufacture and test a Miniature Pulse Tube Cooler (MPTC) to cool infrared detectors for micro-satellite missions. The cooler will be particularly adapted to the needs of the CNES MICROCARB mission to study atmospheric Carbon Dioxide which presents absorption lines in the thermal near infrared, at 1.6 μm and 2.0 μm. The required cooler temperature is from 150 to 200K with cooling power between 1 and 3 watts. The overall electrical power budget including electronics is less than 20W with a 288-300K rejection temperature. Particular attention is therefore paid to optimizing overall system efficiency. The active micro vibration reduction system and thermal control systems already developed for the Air Liquide Large Pulse Tube Cooler (LPTC) are currently being implemented into a new high efficiency electronic architecture. The presented work concerns the new cold finger and electronic design. The cooler uses the compressor already developed for the 80K Miniature Pulse Tube Cryocooler. This Pulse Tube Cooler addresses the requirements of space missions where extended continuous operating life time (>5 years), low mass and low micro vibration levels are critical.

  15. Tritium emissions from 200 East Area Double-Shell Tanks

    SciTech Connect (OSTI)

    Bachand, D.D.

    1994-11-28

    This document evaluates the need for tritium sampling of the emissions from the 200 East Area Double Shell Tanks based on the requirements of {open_quotes}National Emission Standards for Hazardous Air Pollutants{close_quotes} (NESHAP). The NESHAP requirements are specified in 40 Code of Federal Regulation (CFR), Part 61, Subpart H; {open_quotes}National Emission Standards for Emissions of Radionuclides Other than Radon from Department of Energy Facilities{close_quotes}.

  16. $300,000 Block Grant Awarded to Tri-City Industrial Development Council

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    (TRIDEC) | Department of Energy $300,000 Block Grant Awarded to Tri-City Industrial Development Council (TRIDEC) $300,000 Block Grant Awarded to Tri-City Industrial Development Council (TRIDEC) $300,000 Block Grant Awarded to Tri-City Industrial Development Council (TRIDEC) $300,000 Block Grant Awarded to Tri-City Industrial Development Council (TRIDEC) (37.6 KB) More Documents & Publications Department of Energy Awards $300,000 to Tri-City Industrial Development Council in Washington

  17. High Temperature 300°C Directional Drilling System | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    High Temperature 300°C Directional Drilling System High Temperature 300°C Directional Drilling System Project objective: provide a directional drilling system that can be used at environmental temperatures of up to 300°C; and at depths of 10; 000 meters. high_macpherson_ht_directional_drilling.pdf (592.83 KB) More Documents & Publications 300ºC DDS + 300ºC MWD Hotline IV …High Temperature ESP track 3: enhanced geothermal systems (EGS) | geothermal 2015 peer review

  18. Volatile Organic Compound Investigation Results, 300 Area, Hanford Site, Washington

    SciTech Connect (OSTI)

    Peterson, Robert E.; Williams, Bruce A.; Smith, Ronald M.

    2008-07-07

    Unexpectedly high concentrations of volatile organic compounds (VOC) were discovered while drilling in the unconfined aquifer beneath the Hanford Site’s 300 Area during 2006. The discovery involved an interval of relatively finer-grained sediment within the unconfined aquifer, an interval that is not sampled by routine groundwater monitoring. Although VOC contamination in the unconfined aquifer has been identified and monitored, the concentrations of newly discovered contamination are much higher than encountered previously, with some new results significantly higher than the drinking water standards. The primary contaminant is trichloroethene, with lesser amounts of tetrachloroethene. Both chemicals were used extensively as degreasing agents during the fuels fabrication process. A biological degradation product of these chemicals, 1,2-dichloroethene, was also detected. To further define the nature and extent of this contamination, additional characterization drilling was undertaken during 2007. Four locations were drilled to supplement the information obtained at four locations drilled during the earlier investigation in 2006. The results of the combined drilling indicate that the newly discovered contamination is limited to a relatively finer-grained interval of Ringold Formation sediment within the unconfined aquifer. The extent of this contamination appears to be the area immediately east and south of the former South Process Pond. Samples collected from the finer-grained sediment at locations along the shoreline confirm the presence of the contamination near the groundwater/river interface. Contamination was not detected in river water that flows over the area where the river channel potentially incises the finer-grained interval of aquifer sediment. The source for this contamination is not readily apparent. A search of historical documents and the Hanford Waste Information Data System did not provide definitive clues as to waste disposal operations and

  19. Phase I remedial investigation report for the 300-FF-5 operable unit, Volume 1

    SciTech Connect (OSTI)

    1994-01-01

    The focus of this remedial investigation (RI) is the 300-FF-5 operable unit, one of five operable units associated with the 300 Area aggregate of the U.S. Department of Energy`s (DOE`s) Hanford Site. The 300-FF-5 operable unit is a groundwater operable unit beneath the 300-FF-1, 300-FF-2, and 300-FF-3 source operable units. This operable unit was designated to include all contamination detected in the groundwater and sediments below the water table that emanates from the 300-FF-1, 300-FF-2, and 300-FF-3 operable units (DOE-RL 1990a). In November 1989, the U.S. Environmental Protection Agency (EPA) placed the 300 Area on the National Priorities List (NPL) contained within Appendix B of the National Oil and Hazardous Substance Pollution Contingency Plan (NCP, 53 FR 51391 et seq.). The EPA took this action pursuant to their authority under the Comprehensive Environmental Response, Compensation, and Liability Act of 1980 (CERCLA, 42 USC 9601 et seq.). The DOE Richland Operations Office (DOE-RL), the EPA and Washington Department of Ecology (Ecology) issued the Hanford Federal Facility Agreement and Consent Order (Tri-Party Agreement), in May 1989 (Ecology et al. 1992, Rev. 2). This agreement, among other matters, governs all CERCLA efforts at the Hanford Site. In June 1990, a remedial investigation/feasibility study (RI/FS) workplan for the 300-FF-5 operable unit was issued pursuant to the Tri-Party Agreement.

  20. 300 Area Treated Effluent Disposal Facility permit reopener run plan

    SciTech Connect (OSTI)

    Olander, A.R.

    1995-03-10

    The 300 Area Treated Effluent Disposal Facility (TEDF) is authorized to discharge treated effluent to the Columbia River by National Pollutant Discharge Elimination System permit WA-002591-7. The letter accompanying the final permit noted the following: EPA recognizes that the TEDF is a new waste treatment facility for which full scale operation and effluent data has not been generated. The permit being issued by EPA contains discharge limits that are intended to force DOE`s treatment technology to the limit of its capability.`` Because of the excessively tight limits the permit contains a reopener clause which may allow limits to be renegotiated after at least one year of operation. The restrictions for reopening the permit are as follows: (1) The permittee has properly operated and maintained the TEDF for a sufficient period to stabilize treatment plant operations, but has nevertheless been unable to achieve the limitation specified in the permit. (2) Effluent data submitted by the permittee supports the effluent limitation modifications(s). (3) The permittee has submitted a formal request for the effluent limitation modification(s) to the Director. The purpose of this document is to guide plant operations for approximately one year to ensure appropriate data is collected for reopener negotiations.

  1. 200W Pump and Treat Construction Schedule Review

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    W Pump and Treat Construction Schedule Review Section C.2.5.3 - Task Order 11-001 The contractor shall provide the following project independent review services, as requested and as described below.. The Contractor shall perform these services in accordance with Contract DE-AC06-09RL14728, C.2.5.3, Portfolio Management, meet milestones and delivery schedules as established by the AMCP Groundwater and Vadose Zone Remediation Project team, and comply with established criteria. Task 200W P&T-1

  2. INDEPENDENT TECHNICAL REVIEW OF THE C-400 INTERIM REMEDIAL PROJECT PHASE I RESULTS, PADUCAH, KENTUCKY

    SciTech Connect (OSTI)

    Looney, B.; Rossabi, J.; Stewart,L.; Richards, W.

    2010-10-29

    The groundwater and soil in the vicinity of the C-400 Building at the Paducah Gaseous Diffusion Plant (PGDP), is contaminated with substantial quantities of industrial solvents, primarily trichoroethene (TCE). This solvent 'source' is recognized as a significant challenge and an important remediation target in the overall environmental cleanup strategy for PGDP. Thus, the cleanup of the C-400 TCE Source is a principal focus for the Department of Energy (DOE) and its contractors, and for PGDP regulators and stakeholders. Using a formal investigation, feasibility study and decision process, Electrical Resistance Heating (ERH) was selected for the treatment of the soil and groundwater in the vicinity of C-400. ERH was selected as an interim action to remove 'a significant portion of the contaminant mass of TCE at the C-400 Cleaning Building area through treatment' with the longer term goal of reducing 'the period the TCE concentration in groundwater remains above its Maximum Contaminant Level (MCL).' ERH is a thermal treatment that enhances the removal of TCE and related solvents from soil and groundwater. The heterogeneous conditions at PGDP, particularly the high permeability regional gravel aquifer (RGA), are challenging to ERH. Thus, a phased approach is being followed to implement this relatively expensive and complex remediation technology. Conceptually, the phased approach encourages safety and efficiency by providing a 'lessons learned' process and allowing appropriate adjustments to be identified and implemented prior to follow-on phase(s) of treatment. More specifically, early deployment targeted portions of the challenging RGA treatment zone with relatively little contamination reducing the risk of adverse collateral impacts from underperformance in terms of heating and capture. Because of the importance and scope of the C-400 TCE source remediation activities, DOE chartered an Independent Technical Review (ITR) in 2007 to assess the C-400 ERH plans prior

  3. Development of a 400 Level 3C Clamped Downhole Seismic Receiver Array for 3D Borehole Seismic Imaging of Gas Reservoirs

    SciTech Connect (OSTI)

    Bjorn N. P. Paulsson

    2006-09-30

    Borehole seismology is the highest resolution geophysical imaging technique available today to the oil and gas industry for characterization and monitoring of oil and gas reservoirs. However, the industry's ability to perform high resolution 3D imaging of deep and complex gas reservoirs using borehole seismology has been hampered by the lack of acquisition technology necessary to record large volumes of high frequency, high signal-to-noise-ratio borehole seismic data. This project took aim at this shortcoming by developing a 400 level 3C clamped downhole seismic receiver array, and accompanying software, for borehole seismic 3D imaging. This large borehole seismic array has removed the technical acquisition barrier for recording the data volumes necessary to do high resolution 3D VSP and 3D cross-well seismic imaging. Massive 3D VSP{reg_sign} and long range Cross-Well Seismology (CWS) are two of the borehole seismic techniques that promise to take the gas industry to the next level in their quest for higher resolution images of deep and complex oil and gas reservoirs. Today only a fraction of the oil or gas in place is produced when reservoirs are considered depleted. This is primarily due to our lack of understanding of detailed compartmentalization of oil and gas reservoirs. In this project, we developed a 400 level 3C borehole seismic receiver array that allows for economic use of 3D borehole seismic imaging for reservoir characterization and monitoring. This new array has significantly increased the efficiency of recording large data volumes at sufficiently dense spatial sampling to resolve reservoir complexities. The receiver pods have been fabricated and tested to withstand high temperature (200 C/400 F) and high pressure (25,000 psi), so that they can operate in wells up to 7,620 meters (25,000 feet) deep. The receiver array is deployed on standard production or drill tubing. In combination with 3C surface seismic or 3C borehole seismic sources, the 400

  4. Application for Presidential Permit OE Docket No. PP-400 TDI-NE - New

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    England Clean Power Link Project - Comments and Motion to Intervene of Conservation Law Foundation | Department of Energy - New England Clean Power Link Project - Comments and Motion to Intervene of Conservation Law Foundation Application for Presidential Permit OE Docket No. PP-400 TDI-NE - New England Clean Power Link Project - Comments and Motion to Intervene of Conservation Law Foundation Conservation Law Foundation (CLF) provides the following comments and Motion to Intervene regarding

  5. Application for Presidential Permit OE Docket No. PP-400 TDI-NE - New

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    England Clean Power Link Project: Comments and Motion to Intervene Out of Time of Allco Renewable Energy Limited | Department of Energy - New England Clean Power Link Project: Comments and Motion to Intervene Out of Time of Allco Renewable Energy Limited Application for Presidential Permit OE Docket No. PP-400 TDI-NE - New England Clean Power Link Project: Comments and Motion to Intervene Out of Time of Allco Renewable Energy Limited ALLCO Renewable Energy Limited provides the following

  6. Application for Presidential Permit OE Docket No. PP-400 TDI-NE - New

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    England Clean Power Link Project: Federal Register Notice, Volume 79, No. 131 - July 9, 2014 | Department of Energy - New England Clean Power Link Project: Federal Register Notice, Volume 79, No. 131 - July 9, 2014 Application for Presidential Permit OE Docket No. PP-400 TDI-NE - New England Clean Power Link Project: Federal Register Notice, Volume 79, No. 131 - July 9, 2014 Application from TDI-NE to construct, operate and maintain electric transmission facilities at the U.S. - Canada

  7. State waste discharge permit application 400 Area secondary cooling water. Revision 2

    SciTech Connect (OSTI)

    1996-01-01

    This document constitutes the Washington Administrative Code 173-216 State Waste Discharge Permit Application that serves as interim compliance as required by Consent Order DE 91NM-177, for the 400 Area Secondary Cooling Water stream. As part of the Hanford Federal Facility Agreement and Consent Order negotiations, the US Department of Energy, Richland Operations Office, the US Environmental Protection Agency, and the Washington State Department of Ecology agreed that liquid effluent discharges to the ground on the Hanford Site that affect groundwater or have the potential to affect groundwater would be subject to permitting under the structure of Chapter 173-216 of the Washington Administrative Code, the State Waste Discharge Permitting Program. As a result of this decision, the Washington State Department of Ecology and the US Department of Energy, Richland Operations Office entered into Consent Order DE 91NM-177. The Consent Order DE 91NM-177 requires a series of permitting activities for liquid effluent discharges. Based upon compositional and flow rate characteristics, liquid effluent streams on the Hanford Site have been categorized into Phase 1, Phase 2, and Miscellaneous streams. This document only addresses the 400 Area Secondary Cooling Water stream, which has been identified as a Phase 2 stream. The 400 Area Secondary Cooling Water stream includes contribution streams from the Fuels and Materials Examination Facility, the Maintenance and Storage Facility, the 481-A pump house, and the Fast Flux Test Facility.

  8. On Earth Day Vice President Biden Announces $300 Million in Recovery Act

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Funds for Clean Cities Program | Department of Energy On Earth Day Vice President Biden Announces $300 Million in Recovery Act Funds for Clean Cities Program On Earth Day Vice President Biden Announces $300 Million in Recovery Act Funds for Clean Cities Program April 22, 2009 - 12:00am Addthis LANDOVER, MD - During a visit to the WMATA Carmen Turner Maintenance and Training Facility in Landover, MD, Vice President Joe Biden today announced $300 million in funding from the American Recovery

  9. Department of Energy Awards $300,000 Block Grant to the Rocky...

    Broader source: Energy.gov (indexed) [DOE]

    Block Grant to the Rocky Flats Community Reuse Organization Department of Energy Awards 300,000 Block Grant to the Rocky Flats Community Reuse Organization More Documents &...

  10. 300 AREA PACIFIC NORTHWEST NATIONAL LABORATORY FACILITY RADIONUCLIDE EMISSION POINTS AND SAMPLING SYSTEMS

    SciTech Connect (OSTI)

    Barfuss, Brad C.; Barnett, J. M.; Harbinson, L Jill

    2006-08-28

    Radionuclide emission points for 300 Area and Battelle Private facilities are presented herein. The sampling systems and associated emission specifics are detailed.

  11. Ubiquitination of Notch1 is regulated by MAML1-mediated p300 acetylation of Notch1

    SciTech Connect (OSTI)

    Popko-Scibor, Anita E.; Lindberg, Mikael J.; Hansson, Magnus L.; Holmlund, Teresa; Wallberg, Annika E.

    2011-12-16

    Highlights: Black-Right-Pointing-Pointer p300 acetylates conserved lysines within Notch1 C-terminal nuclear localization signal. Black-Right-Pointing-Pointer MAML1 and CSL, components of Notch transcription complex, increase Notch acetylation. Black-Right-Pointing-Pointer MAML1-dependent acetylation of Notch1 by p300 decreases the ubiquitination of Notch1. Black-Right-Pointing-Pointer CDK8 inhibits Notch acetylation and Notch transcription enhanced by p300. -- Abstract: Earlier studies demonstrated the involvement of the p300 histone acetyltransferase in Notch signaling but the precise mechanisms by which p300 might modulate Notch function remains to be investigated. In this study, we show that p300 acetylates Notch1 ICD in cell culture assay and in vitro, and conserved lysines located within the Notch C-terminal nuclear localization signal are essential for Notch acetylation. MAML1 and CSL, which are components of the Notch transcription complex, enhance Notch acetylation and we suggest that MAML1 increases Notch acetylation by potentiating p300 autoacetylation. Furthermore, MAML1-dependent acetylation of Notch1 ICD by p300 decreases the ubiquitination of Notch1 ICD in cellular assays. CDK8 has been shown to target Notch1 for ubiquitination and proteosomal degradation. We show that CDK8 inhibits Notch acetylation and Notch transcription enhanced by p300. Therefore, we speculate that acetylation of Notch1 might be a mechanism to regulate Notch activity by interfering with ubiquitin-dependent pathways.

  12. 300 Area D4 Project Fiscal Year 2010 Building Completion Report

    SciTech Connect (OSTI)

    Skwarek, B. J.

    2011-01-27

    This report summarizes the deactiviation, decontamination, decommissioning, and demolition activities of facilities in the 300 Area of the Hanford Site in fiscal year 2010.

  13. Uranium Geochemistry in Vadose Zone and Aquifer Sediments from the 300 Area Uranium Plume

    SciTech Connect (OSTI)

    Zachara, John M.; Davis, Jim A.; Liu, Chongxuan; McKinley, James P.; Qafoku, Nik; Wellman, Dawn M.; Yabusaki, Steven B.

    2005-07-21

    This report documents research conducted by the RCS Project to update the record of decision for the 300-FF-5 Operable Unit on the Hanford Site.

  14. H.A.R. 13-300 - Rules of Practice and Procedure Relating to Burial...

    Open Energy Info (EERE)

    300 - Rules of Practice and Procedure Relating to Burial Sites and Human Remains Jump to: navigation, search OpenEI Reference LibraryAdd to library Legal Document-...

  15. Richland Operations Office Completes Cleanup in Hanford’s 300 Area North Section

    Broader source: Energy.gov [DOE]

    RICHLAND, Wash. – EM met a Tri-Party Agreement milestone by completing cleanup of the north portion of Hanford’s 300 Area.

  16. Measurement and control system for cryogenic helium gas bearing turbo-expander experimental platform based on Siemens PLC S7-300

    SciTech Connect (OSTI)

    Li, J.; Xiong, L. Y.; Peng, N.; Dong, B.; Liu, L. Q.; Wang, P.

    2014-01-29

    An experimental platform for cryogenic Helium gas bearing turbo-expanders is established at the Technical Institute of Physics and Chemistry, Chinese Academy of Sciences. This turbo-expander experimental platform is designed for performance testing and experimental research on Helium turbo-expanders with different sizes from the liquid hydrogen temperature to the room temperature region. A measurement and control system based on Siemens PLC S7-300 for this turbo-expander experimental platform is developed. Proper sensors are selected to measure such parameters as temperature, pressure, rotation speed and air flow rate. All the collected data to be processed are transformed and transmitted to S7-300 CPU. Siemens S7-300 series PLC CPU315-2PN/DP is as master station and two sets of ET200M DP remote expand I/O is as slave station. Profibus-DP field communication is established between master station and slave stations. The upper computer Human Machine Interface (HMI) is compiled using Siemens configuration software WinCC V6.2. The upper computer communicates with PLC by means of industrial Ethernet. Centralized monitoring and distributed control is achieved. Experimental results show that this measurement and control system has fulfilled the test requirement for the turbo-expander experimental platform.

  17. Results of 200 KW fuel cell evaluation programs

    SciTech Connect (OSTI)

    Torrey, J.M.; Merten, G.P.; Binder, M.J.

    1996-12-31

    Science Applications International Corporation (SAIC) has installed six monitoring systems on ONSI Corporation 200 kW phosphoric acid fuel cells. Three of the systems were installed for the U.S. Army Construction Engineering Research Laboratories (USACERL) which is coordinating the Department of Defense (DoD) fuel cell Demonstration Program and three were installed under a contract with the New York State Energy Research and Development Authority (NYSERDA). Monitoring of the three NYSERDA sites has been completed. Monitoring systems for the DoD fuel cells were installed in August, 1996 and thus no operating data was available at the time of this writing, but will be presented at the Fuel Cell Seminar. This paper will present the monitoring configuration and research approach for each program. Additionally, summary performance data is presented for the completed NYSERDA program.

  18. POLYSHIFT Communications Software for the Connection Machine System CM-200

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    George, William; Brickner, Ralph G.; Johnsson, S. Lennart

    1994-01-01

    We describe the use and implementation of a polyshift function PSHIFT for circular shifts and end-offs shifts. Polyshift is useful in many scientific codes using regular grids, such as finite difference codes in several dimensions, and multigrid codes, molecular dynamics computations, and in lattice gauge physics computations, such as quantum chromodynamics (QCD) calculations. Our implementation of the PSHIFT function on the Connection Machine systems CM-2 and CM-200 offers a speedup of up to a factor of 3–4 compared with CSHIFT when the local data motion within a node is small. The PSHIFT routine is included in the Connection Machine Scientificmore » Software Library (CMSSL).« less

  19. Repeated compressive stress increase with 400 [degree]C thermal cycling in tantalum thin films due to increases in the oxygen content

    SciTech Connect (OSTI)

    Cabral, C. Jr.; Clevenger, L.A.; Schad, R.G. )

    1994-07-01

    Stresses which build up in thin films such as tantalum, during thermal processing, can cause major reliability problems in electronic and x-ray optics applications. We demonstrate that 50--200 nm thick sputtered [beta]-Ta thin films undergo repeated compressive stress increases when thermally cycled to 400 [degree]C (at a rate of 10 [degree]C/min) and back in a purified He ambient because of small amounts of oxygen gettered by the tantalum. The oxygen contamination results from the poor quality of the atmospheric seal on the quartz annealing chamber. As-deposited Ta thin films have a compressive stress ranging from [minus]1 to [minus]4 GPa. The compressive stress buildup was monitored [ital in] [ital situ] and was shown to increase [minus]0.5 GPa on average after each thermal cycle for a final value from [minus]6 to [minus]7 GPa after seven cycles. After being cycled thermally seven times any perturbation of the film such as a four-point probe resistivity measurement can cause the film to instantaneously crack in a serpentine pattern, relieving the large compressive stress. Auger electron spectroscopy depth profiling analysis was used to determine that the as-deposited film contained 1 at. % oxygen which increased to 8%--12% after seven thermal cycles with an approximate doubling in resistivity. The [minus]0.5 GPa average compressive stress increase in Ta thin films when cycled to 400 [degree]C is attributed to a 1.3% increase in oxygen concentration leading to a Ta unit cell expansion of 0.6%.

  20. DETAILED ANALYSIS OF THE MOST PROMISING ALTERNATIVES TO USING GRANULAR ACTIVATED CARBON TO TREAT 200-ZP-1 GROUNDWATER AND 200-PW-1 SOIL VAPOR

    SciTech Connect (OSTI)

    BYRNES ME, KALMAR JA

    2007-11-26

    This document presents a detailed evaluation of selected alternative treatment options to granular activated carbon (GAC) for removing carbon tetrachloride generated from the groundwater pump-and-treat system at the 200-ZP-I Operable Unit (OU) in the 200 West Area of the Hanford Site. This evaluation of alternative treatment options to GAC is also applicable to the vadose zone soil vapor extraction (SVE) system at the 200-PW-l OU, which is also located in the Hanford Site's 200 West Area.

  1. LLNL Site 200 Risk Management PlanAgust 2008

    SciTech Connect (OSTI)

    Pinkston, D; Johnson, M

    2008-07-30

    been included as an appendix to the RMP Supplemental Information document. LLNL Site 200 is a research and development laboratory with infrastructure necessary to support its operations and personnel. Research and development activities at LLNL are focused on stockpile stewardship; achieving robust and vital scientific, engineering, and manufacturing capability; inertial confinement fusion; laser technology; materials and process science; computational and information sciences; basic sciences; engineering sciences; and biological sciences. Based upon CalARP Program regulations, guidance found in California Accidental Release Prevention Program (CalARP) Administering Guidance, Chapter 1, a review of facility specific documents, accident analyses summarized in this document & detailed in the LLNL Site 200 RMP Supporting Information document, LLNL has determined that each process meeting the CalARP threshold criteria meets the requirements for CalARP Program Level 1. In accordance with CalARP regulations, LLNL considers the natural segmentation of processes at Site 200 to be on a building basis and therefore consideration of inventory should be on a building basis rather than a 'site-wide' basis. Only those materials identified as equal to as or greater than the threshold quantities for the CalARP program on a building (process) level are reflected in this document. As such, materials and quantities reported in this document on a building (process) level will vary from materials and quantities reported in the LLNL Hazardous Materials Business Plan, Acutely Hazardous Material Registration Form on a site-wide level. For each process involving regulated quantities of lithium hydride, worst case accident analysis shows that the toxic endpoint lies within the site boundaries. These analyses document that the nearest public receptor is beyond the distance to a toxic or flammable endpoint. Refer to the LLNL Site 200 RMP Supporting Information document for a more detailed

  2. Modeling and Simulations for the High Flux Isotope Reactor Cycle 400

    SciTech Connect (OSTI)

    Ilas, Germina; Chandler, David; Ade, Brian J; Sunny, Eva E; Betzler, Benjamin R; Pinkston, Daniel

    2015-03-01

    A concerted effort over the past few years has been focused on enhancing the core model for the High Flux Isotope Reactor (HFIR), as part of a comprehensive study for HFIR conversion from high-enriched uranium (HEU) to low-enriched uranium (LEU) fuel. At this time, the core model used to perform analyses in support of HFIR operation is an MCNP model for the beginning of Cycle 400, which was documented in detail in a 2005 technical report. A HFIR core depletion model that is based on current state-of-the-art methods and nuclear data was needed to serve as reference for the design of an LEU fuel for HFIR. The recent enhancements in modeling and simulations for HFIR that are discussed in the present report include: (1) revision of the 2005 MCNP model for the beginning of Cycle 400 to improve the modeling data and assumptions as necessary based on appropriate primary reference sources HFIR drawings and reports; (2) improvement of the fuel region model, including an explicit representation for the involute fuel plate geometry that is characteristic to HFIR fuel; and (3) revision of the Monte Carlo-based depletion model for HFIR in use since 2009 but never documented in detail, with the development of a new depletion model for the HFIR explicit fuel plate representation. The new HFIR models for Cycle 400 are used to determine various metrics of relevance to reactor performance and safety assessments. The calculated metrics are compared, where possible, with measurement data from preconstruction critical experiments at HFIR, data included in the current HFIR safety analysis report, and/or data from previous calculations performed with different methods or codes. The results of the analyses show that the models presented in this report provide a robust and reliable basis for HFIR analyses.

  3. Application for Presidential Permit OE Docket No. PP-400 TDI-NE New England

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Clean Power Link Project: Comments and Motion to Intervene Out of Time of Allco Renewable Energy Limited from TDI | Department of Energy New England Clean Power Link Project: Comments and Motion to Intervene Out of Time of Allco Renewable Energy Limited from TDI Application for Presidential Permit OE Docket No. PP-400 TDI-NE New England Clean Power Link Project: Comments and Motion to Intervene Out of Time of Allco Renewable Energy Limited from TDI TDI offers their response to Allco

  4. Volume Reflection Dependence of 400 GeV/c Protons on the Bent Crystal Curvature

    SciTech Connect (OSTI)

    Scandale, W.; Vomiero, A.; Baricordi, S.; Dalpiaz, P.; Fiorini, M.; Guidi, V.; Mazzolari, A.; Milan, R.; Della Mea, Gianantonio; Ambrosi, G.; Zuccon, P.; Bertucci, B.; Burger, W. J.; Duranti, M.; Cavoto, G.; Santacesaria, R.; Valente, P.; Iacoangeli, F.; Pisano, S.; Luci, C.

    2008-12-05

    The trend of volume reflection parameters (deflection angle and efficiency) in a bent (110) silicon crystal has been investigated as a function of the crystal curvature with 400 GeV/c protons on the H8 beam line at the CERN Super Proton Synchrotron. This Letter describes the analysis performed at six different curvatures showing that the optimal radius for volume reflection is approximately 10 times greater than the critical radius for channeling. A strong scattering of the beam by the planar potential is also observed for a bend radius close to the critical one.

  5. USACE ER 200-2-2 Procedures for Implementing NEPA | Open Energy...

    Open Energy Info (EERE)

    ER 200-2-2 Procedures for Implementing NEPA Jump to: navigation, search OpenEI Reference LibraryAdd to library PermittingRegulatory Guidance - GuideHandbook: USACE ER 200-2-2...

  6. ARS Title 49-200 Water Quality Control | Open Energy Information

    Open Energy Info (EERE)

    -200 Water Quality Control Jump to: navigation, search OpenEI Reference LibraryAdd to library Legal Document- StatuteStatute: ARS Title 49-200 Water Quality ControlLegal Abstract...

  7. Search for Neutrinoless Double-Beta Decay in 136Xe with EXO-200...

    Office of Scientific and Technical Information (OSTI)

    Neutrinoless Double-Beta Decay in 136Xe with EXO-200 Citation Details In-Document Search Title: Search for Neutrinoless Double-Beta Decay in 136Xe with EXO-200 Authors: Auger, M. ;...

  8. DOE to Remove 200 Metric Tons of Highly Enriched Uranium from...

    Energy Savers [EERE]

    200 Metric Tons of Highly Enriched Uranium from U.S. Nuclear Weapons Stockpile DOE to Remove 200 Metric Tons of Highly Enriched Uranium from U.S. Nuclear Weapons Stockpile ...

  9. Three-Dimensional Groundwater Models of the 300 Area at the Hanford Site, Washington State

    SciTech Connect (OSTI)

    Williams, Mark D.; Rockhold, Mark L.; Thorne, Paul D.; Chen, Yousu

    2008-09-01

    Researchers at Pacific Northwest National Laboratory developed field-scale groundwater flow and transport simulations of the 300 Area to support the 300-FF-5 Operable Unit Phase III Feasibility Study. The 300 Area is located in the southeast portion of the U.S. Department of Energy’s Hanford Site in Washington State. Historical operations involving uranium fuel fabrication and research activities at the 300 Area have contaminated engineered liquid-waste disposal facilities, the underlying vadose zone, and the uppermost aquifer with uranium. The main objectives of this research were to develop numerical groundwater flow and transport models to help refine the site conceptual model, and to assist assessment of proposed alternative remediation technologies focused on the 300 Area uranium plume.

  10. PDSF Office Hours 1/23/14 from 2:30 to 4:00 pm at LBNL

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    /23/14 from 2:30 to 4:00 pm at LBNL PDSF Office Hours 1/23/14 from 2:30 to 4:00 pm at LBNL January 22, 2014 PDSF office hours will be from 2:30 to 4:00 pm in 50B-2222 tomorrow. Subscribe via RSS Subscribe Browse by Date February 2014 January 2014 November 2013 October 2013 September 2013 August 2013 March 2012 February 2012 January 2012 October 2011 July 2011 May 2011 April 2011 March 2011 February 2011 January 2011 December 2010 Last edited: 2014-01-22 16:33:02

  11. Irradiation creep of various ferritic alloys irradiated {approximately}400 C in the PFR and FFTF reactors

    SciTech Connect (OSTI)

    Toloczko, M.B.; Garner, F.A.; Eiholzer, C.R.

    1998-03-01

    Three ferritic alloys were irradiated in two fast reactors to doses of 50 dpa or more at temperatures near 400 C. One martensitic alloy, HT9, was irradiated in both the FFTF and PFR reactors. PFR is the Prototype Fast Reactor in Dourneay, Scotland, and FFTF is the Fast Flux Test Facility in Richland, WA. D57 is a developmental alloy that was irradiated in PFR only, and MA957 is a Y{sub 2}O{sub 3} dispersion-hardened ferritic alloy that was irradiated only in FFTF. These alloys exhibited little or no void swelling at {approximately}400 C. Depending on the alloy starting condition, these steels develop a variety of non-creep strains early in the irradiation that are associated with phase changes. Each of these alloys creeps at a rate that is significantly lower than that of austenitic steels irradiated in the same experiments. The creep compliance for ferritic alloys in general appears to be {approximately}0.5 {times} 10{sup {minus}6} MPa{sup {minus}1} dpa{sup {minus}1}, independent of both composition and starting state. The addition of Y{sub 2}O{sub 3} as a dispersoid does not appear to change the creep behavior.

  12. Secretary Chu Announces Major New Recovery Act Milestone: 300,000 Homes

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Weatherized | Department of Energy Major New Recovery Act Milestone: 300,000 Homes Weatherized Secretary Chu Announces Major New Recovery Act Milestone: 300,000 Homes Weatherized January 19, 2011 - 12:00am Addthis WASHINGTON - U.S. Department of Energy Secretary Steven Chu today announced that states and territories across the country have now weatherized more than 300,000 low-income homes under the Recovery Act, a major milestone in the Department's efforts to reduce home energy bills for

  13. Drilling, Sampling, and Well-Installation Plan for the IFC Well Field, 300 Area

    SciTech Connect (OSTI)

    Bjornstad, Bruce N.; Horner, Jacob A.

    2008-05-05

    The 300 Area was selected as a location for an IFC because it offers excellent opportunities for field research on the influence of mass-transfer processes on uranium in the vadose zone and groundwater. The 300 Area was the location of nuclear fuel fabrication facilities and has more than 100 waste sites. Two of these waste sites, the North and South Process Ponds received large volumes of process waste from 1943 to 1975 and are thought to represent a significant source of the groundwater uranium plume in the 300 Area. Geophysical surveys and other characterization efforts have led to selection of the South Process Pond for the IFC.

  14. Molecular dynamics for 400 million particles with short-range interactions

    SciTech Connect (OSTI)

    Deng, Y.; McCoy, R.A.; Marr, R.B.

    1995-07-01

    We report the design and performance of a computational molecular dynamics (MD) code for 400 million particles interacting through the standard pairwise 6-12 Lennard-Jones potential on a 1024-node Intel Paragon, a distributed-memory MIMD parallel computer. The initially recorded {open_quotes}particle-step time{close_quotes} was .4 microseconds. A new inter-node communication strategy ensures high parallel efficiency for a large number of nodes. Besides the ability to tackle large problems, our implementation incorporates a novel method for dynamic load balancing. Our communication and load balancing enhancements provide increased efficiency and flexibility for our MD code. vet are general enough for use in other parallel algorithms.

  15. NEUTRON-INDUCED SWELLING OF Fe-Cr BINARY ALLOYS IN FFTF AT ~400 DEGREES C

    SciTech Connect (OSTI)

    Garner, Francis A.; Greenwood, Lawrence R.; Okita, Taira; Sekimura, Naoto; Wolfer, W. G.

    2002-12-31

    The purpose of this effort is to determine the influence of dpa rate, He/dpa ratio and composition on the void swelling of simple binary Fe-Cr alloys. Contrary to the behavior of swelling of model fcc Fe-Cr-Ni alloys irradiated in the same FFTF-MOTA experiment, model bcc Fe-Cr alloys do not exhibit a dependence of swelling on dpa rate at approximately 400 degrees C. This is surprising in that an apparent flux-sensitivity was observed in an earlier comparative irradiation of Fe-Cr binaries conducted in EBR-II and FFTF. The difference in behavior is ascribed to the higher helium generation rates of Fe-Cr alloys in EBR-II compared to that of FFTF, and also the fact that lower dpa rates in FFTF are accompanied by progressively lower helium generation rates.

  16. Comparative study of the embrittlement of Monel 400 at room temperature by hydrogen and by mercury

    SciTech Connect (OSTI)

    Price, C.E.; Fredell, R.S.

    1986-05-01

    Slow strain rate tensile tests were performed at room temperature on Monel 400 specimens of grain sizes 35 to 500 microns, in the environments of air, mercury, and electrolytically generated hydrogen. Specimens of grain size 250 microns were tested at a range of strain rates in the three environments. It was found that cracks initiated easiest in hydrogen but propagated easiest in mercury; consequently the embrittlement was usually more severe in mercury. The embrittlement decreased with increasing strain rate, and with increasing grain size in hydrogen. Embrittlement in mercury was maximum at intermediate grain sizes. A fracture sequence of intergranular to transgranular to microvoid coalescence was common. The intergranular and transgranular fractures are interpreted in terms of the reduced cohesive stress and enhanced shear models of embrittlement, respectively. 52 references.

  17. Test of a 1.8 Tesla, 400 Hz Dipole for a Muon Synchrotron

    SciTech Connect (OSTI)

    Summers, D.J.; Cremaldi, L.M.; Hart, T.L.; Perera, L.P.; Reep, M.; Witte, H.; Hansen, S.; Lopes, M.L.; Reidy Jr., J.; /Oxford High School

    2012-05-01

    A 1.8 T dipole magnet using thin grain oriented silicon steel laminations has been constructed as a prototype for a muon synchrotron ramping at 400 Hz. Following the practice in large 3 phase transformers and our own Opera-2d simulations, joints are mitred to take advantage of the magnetic properties of the steel which are much better in the direction in which the steel was rolled. Measurements with a Hysteresigraph 5500 and Epstein frame show a high magnetic permeability which minimizes stored energy in the yoke allowing the magnet to ramp quickly with modest voltage. Coercivity is low which minimizes hysteresis losses. A power supply with a fast Insulated Gate Bipolar Transistor (IGBT) switch and a capacitor was constructed. Coils are wound with 12 gauge copper wire. Thin wire and laminations minimize eddy current losses. The magnetic field was measured with a peak sensing Hall probe.

  18. Development of a Scale Model for High Flux Isotope Reactor Cycle 400

    SciTech Connect (OSTI)

    Ilas, Dan

    2012-03-01

    The development of a comprehensive SCALE computational model for the High Flux Isotope Reactor (HFIR) is documented and discussed in this report. The SCALE model has equivalent features and functionality as the reference MCNP model for Cycle 400 that has been used extensively for HFIR safety analyses and for HFIR experiment design and analyses. Numerical comparisons of the SCALE and MCNP models for the multiplication constant, power density distribution in the fuel, and neutron fluxes at several locations in HFIR indicate excellent agreement between the results predicted with the two models. The SCALE HFIR model is presented in sufficient detail to provide the users of the model with a tool that can be easily customized for various safety analysis or experiment design requirements.

  19. Response of 9Cr-ODS Steel to Proton Irradiation at 400 °C

    SciTech Connect (OSTI)

    Jianchao He; Farong Wan; Kumar Sridharan; Todd R. Allen; A. Certain; Y. Q. Wu

    2014-09-01

    The stability of Y–Ti–O nanoclusters, dislocation structure, and grain boundary segregation in 9Cr-ODS steels has been investigated following proton irradiation at 400 °C with damage levels up to 3.7 dpa. A slight coarsening and a decrease in number density of nanoclusters were observed as a result of irradiation. The composition of nanoclusters was also observed to change with a slight increase of Y and Cr concentration in the nanoclusters following irradiation. Size, density, and composition of the nanoclusters were investigated as a function of nanocluster size, specifically classified to three groups. In addition to the changes in nanoclusters, dislocation loops were observed after irradiation. Finally, radiation-induced enrichment of Cr and depletion of W were observed at grain boundaries after irradiation.

  20. Characterization of Biofilm in 200W Fluidized Bed Reactors

    SciTech Connect (OSTI)

    Lee, Michelle H.; Saurey, Sabrina D.; Lee, Brady D.; Parker, Kent E.; Eisenhauer, Emalee ER; Cordova, Elsa A.; Golovich, Elizabeth C.

    2014-09-29

    Contaminated groundwater beneath the 200 West Area at the Hanford Site in Southeast Washington is currently being treated using a pump and treat system to remove organics, inorganics, radionuclides, and metals. A granular activated carbon-based fluidized bed reactor (FBR) has been added to remove nitrate, hexavalent chromium and carbon tetrachloride. Initial analytical results indicated the microorganisms effectively reduced many of the contaminants to less than cleanup levels. However shortly thereafter operational upsets of the FBR include carbon carry over, over production of microbial extracellular polymeric substance (biofilm) materials, and over production of hydrogen sulfide. As a result detailed investigations were undertaken to understand the functional diversity and activity of the microbial community present in the FBR over time. Molecular analyses including terminal restriction fragment length polymorphism analysis, quantitative polymerase chain reaction and fluorescent in situ hybridization analyses were performed on the microbial community extracted from the biofilm within the bed and from the inoculum, to determine functional dynamics of the FBR bed over time and following operational changes. Findings from these analyses indicated: 1) the microbial community within the bed was completely different than community used for inoculation, and was likely from the groundwater; 2) analyses early in the testing showed an FBR community dominated by a few Curvibacter and Flavobacterium species; 3) the final sample taken indicated that the microbial community in the FBR bed had become more diverse; and 4) qPCR analyses indicated that bacteria involved in nitrogen cycling, including denitrifiers and anaerobic ammonia oxidizing bacteria, were dominant in the bed. These results indicate that molecular tools can be powerful for determining functional diversity within FBR type reactors. Coupled with micronutrient, influent and effluent chemistry evaluations, a more

  1. RENEW300: Advancing Renewable Energy at HUD-Assisted Housing- Minneapolis

    Broader source: Energy.gov [DOE]

    Hosted by the U.S. Department of Housing and Urban Development (HUD), this workshop helps providers and owners understand the tools and resources available via HUD's RENEW300 initiative.

  2. RENEW300: Advancing Renewable Energy at HUD-Assisted Housing- Atlanta

    Broader source: Energy.gov [DOE]

    Hosted by the U.S. Department of Housing and Urban Development (HUD), this workshop helps providers and owners understand the tools and resources available via HUD's RENEW300 initiative.

  3. 300 Area Integrated Field-Scale Subsurface Research Challenge (IFRC) Field Site Management Plan

    SciTech Connect (OSTI)

    Freshley, Mark D.

    2008-12-31

    Pacific Northwest National Laboratory (PNNL) has established the 300 Area Integrated Field-Scale Subsurface Research Challenge (300 Area IFRC) on the Hanford Site in southeastern Washington State for the U.S. Department of Energy’s (DOE) Office of Biological and Environmental Research (BER) within the Office of Science. The project is funded by the Environmental Remediation Sciences Division (ERSD). The purpose of the project is to conduct research at the 300 IFRC to investigate multi-scale mass transfer processes associated with a subsurface uranium plume impacting both the vadose zone and groundwater. The management approach for the 300 Area IFRC requires that a Field Site Management Plan be developed. This is an update of the plan to reflect the installation of the well network and other changes.

  4. 1,153-ton Waste Vault Removed from 300 Area - Vault held waste...

    Broader source: Energy.gov (indexed) [DOE]

    the removal of a massive concrete vault that once held two 15,000-gallon stainless steel tanks used to collect highly contaminated waste from Hanford's 300 Area laboratories as ...

  5. National Ignition Facility fires 300th laser target shot of fiscal year

    National Nuclear Security Administration (NNSA)

    2015 | National Nuclear Security Administration | (NNSA) Ignition Facility fires 300th laser target shot of fiscal year 2015 August 18, 2015 WASHINGTON - Last week, the National Ignition Facility (NIF) fired its 300th laser target shot in fiscal year (FY) 2015, meeting the year's goal more than six weeks early. In comparison, the facility completed 191 target shots in FY 2014. Located at Lawrence Livermore National Laboratory (LLNL), the NIF is the world's most energetic laser. Increasing

  6. Lawrence Livermore's 'Site 300' looks back on 60 years of significant

    National Nuclear Security Administration (NNSA)

    scientific contributions | National Nuclear Security Administration | (NNSA) Lawrence Livermore's 'Site 300' looks back on 60 years of significant scientific contributions Monday, September 28, 2015 - 4:58pm NNSA Blog The entrance to Site 300 circa 1955. Sixty years ago, the University of California Radiation Laboratory began testing high explosives at what would become one of the nation's most sophisticated non-nuclear weapons testing sites, an 11 square-mile plot of rural grassland tucked

  7. Archived News Item: August 26, 2009 - Secretary Chu Announces Nearly $300

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Million in Clean Cities Grants to Support Clean Fuels, Vehicles, and Infrastructure Development | Department of Energy 26, 2009 - Secretary Chu Announces Nearly $300 Million in Clean Cities Grants to Support Clean Fuels, Vehicles, and Infrastructure Development Archived News Item: August 26, 2009 - Secretary Chu Announces Nearly $300 Million in Clean Cities Grants to Support Clean Fuels, Vehicles, and Infrastructure Development August 26, 2009 This page has been recreated from a retired EERE

  8. Solar and Energy Loan Fund Receives $300,000 Community Reinvestment Act

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Loan to Invest in Home Energy Upgrades | Department of Energy Solar and Energy Loan Fund Receives $300,000 Community Reinvestment Act Loan to Invest in Home Energy Upgrades Solar and Energy Loan Fund Receives $300,000 Community Reinvestment Act Loan to Invest in Home Energy Upgrades Photo of a group of people standing with a sign looking at the camera. Residential Network member and Better Buildings Neighborhood Program partner Solar and Energy Loan Fund (SELF) received its first Community

  9. Toward 300 Miles on a Single Charge? | U.S. DOE Office of Science (SC)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Toward 300 Miles on a Single Charge? News News Home Featured Articles 2016 2015 2014 2013 2012 2011 2010 2009 2008 2007 2006 2005 Science Headlines Science Highlights Presentations & Testimony News Archives Communications and Public Affairs Contact Information Office of Science U.S. Department of Energy 1000 Independence Ave., SW Washington, DC 20585 P: (202) 586-5430 11.27.13 Toward 300 Miles on a Single Charge? Berkeley Lab scientists design a high-performance, long cycle-life

  10. Obama Administration Announces Additional $14,521,300 for Local Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Efficiency Improvements in Rhode Island | Department of Energy 4,521,300 for Local Energy Efficiency Improvements in Rhode Island Obama Administration Announces Additional $14,521,300 for Local Energy Efficiency Improvements in Rhode Island March 26, 2009 - 12:00am Addthis WASHINGTON - Vice President Joe Biden and Energy Secretary Steven Chu today announced plans to invest $3.2 billion in energy efficiency and conservation projects in U.S. cities, counties, states, territories, and Native

  11. Innovative Cell Materials and Designs for 300 Mile Range EVs | Department

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    of Energy 2 DOE Hydrogen and Fuel Cells Program and Vehicle Technologies Program Annual Merit Review and Peer Evaluation Meeting es130_zhu_2012_p.pdf (1.04 MB) More Documents & Publications Vehicle Technologies Office Merit Review 2014: Innovative Cell Materials and Design for 300 Mile Range EVs Innovative Cell Materials and Designs for 300 Mile Range EVs U.S. Battery R&D Progress and Plans

  12. Innovative Cell Materials and Designs for 300 Mile Range EVs | Department

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    of Energy 3 DOE Hydrogen and Fuel Cells Program and Vehicle Technologies Program Annual Merit Review and Peer Evaluation Meeting es130_zhu_2013_p.pdf (1.37 MB) More Documents & Publications Vehicle Technologies Office Merit Review 2014: Innovative Cell Materials and Design for 300 Mile Range EVs Innovative Cell Materials and Designs for 300 Mile Range EVs Vehicle Technologies Office Merit Review 2016: Advanced High-Performance Batteries for Electric Vehicle (EV) Applications

  13. Investigation of hydrogen isotope exchange reaction rate in mixed gas (H{sub 2} and D{sub 2}) at pressure up to 200 MPa using Raman spectroscopy

    SciTech Connect (OSTI)

    Tikhonov, V.V.; Yukhimchuk, A.A.; Musyayev, R.K.; Gurkin, A.I.

    2015-03-15

    Raman spectroscopy is a relevant method for obtaining objective data on isotopic exchange rate in a gaseous mix of hydrogen isotopes, since it allows one to determine a gaseous mix composition in real time without sampling. We have developed a high-pressure fiber-optic probe to be used for obtaining protium Raman spectra under pressures up to 400 MPa and we have recorded spectral line broadening induced by molecule collisions starting from ∼ 40 MPa. Using this fiber-optic probe we have performed experiments to study isotopic exchange kinetics in a gaseous mix of hydrogen isotopes (protium-deuterium) at pressures up to 200 MPa. Preliminary results show that the dependence of the average isotopic exchange rate related to pressure take unexpected values at the very beginning of the time evolution. More work is required to understand this inconsistency.

  14. Department of Energy Awards $300,000 to Albuquerque’s Next Generation Economy Community Reuse Organization

    Broader source: Energy.gov [DOE]

    Department of Energy Awards $300,000 to Albuquerque’s Next Generation Economy Community Reuse Organization

  15. SRP engineering and design history, Vol III, 200 F and H Areas

    SciTech Connect (OSTI)

    Banick, C.J.

    2000-04-17

    This volume combines the record of events relating to the development of design for both the 200-F and H Areas. Chronologically, the definition of plant facilities was first established for the 200-F Area. The second area, 200-H, was projected initially to be a supplementary plutonium separations facility. This history explains the differences in character and capacity of the manufacturing facilities in both areas as production requirements and experience with separations processes advanced.

  16. Secretary Chu Announces more than $200 Million for Solar and Water Power

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Technologies | Department of Energy more than $200 Million for Solar and Water Power Technologies Secretary Chu Announces more than $200 Million for Solar and Water Power Technologies April 22, 2010 - 12:00am Addthis WASHINGTON, DC - On the 40th Anniversary of Earth Day, U.S. Department of Energy Secretary Steven Chu announced that the Department will invest more than $200 million over five years to expand and accelerate the development, commercialization, and use of solar and water power

  17. Final Technical Report - 300???°C Capable Electronics Platform and Temperature Sensor System For Enhanced Geothermal Systems

    SciTech Connect (OSTI)

    Cheng-Po Chen; David Shaddock; Peter Sandvik; Rich Saia; Amita Patil, Alexey Vert; Tan Zhang

    2012-11-30

    A silicon carbide (SiC) based electronic temperature sensor prototype has been demonstrated to operate at 300???°C. We showed continuous operation of 1,000 hours with SiC operational amplifier and surface mounted discreet resistors and capacitors on a ceramic circuit board. This feasibility demonstration is a major milestone in the development of high temperature electronics in general and high temperature geothermal exploration and well management tools in particular. SiC technology offers technical advantages that are not found in competing technologies such as silicon-on-insulator (SOI) at high temperatures of 200???°C to 300???°C and beyond. The SiC integrated circuits and packaging methods can be used in new product introduction by GE Oil and Gas for high temperature down-hole tools. The existing SiC fabrication facility at GE is sufficient to support the quantities currently demanded by the marketplace, and there are other entities in the United States and other countries capable of ramping up SiC technology manufacturing. The ceramic circuit boards are different from traditional organic-based electronics circuit boards, but the fabrication process is compatible with existing ceramic substrate manufacturing. This project has brought high temperature electronics forward, and brings us closer to commercializing tools that will enable and reduce the cost of enhanced geothermal technology to benefit the public in terms of providing clean renewable energy at lower costs.

  18. Remedial System Performance Improvement for the 200-ZP-1_PW-1 Operable

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Units at Hanford | Department of Energy Remedial System Performance Improvement for the 200-ZP-1_PW-1 Operable Units at Hanford Remedial System Performance Improvement for the 200-ZP-1_PW-1 Operable Units at Hanford Full Document and Summary Versions are available for download Remedial System Performance Improvement for the 200-ZP-1_PW-1 Operable Units at Hanford (395.47 KB) Summary - Remedial System Performance Improvement for the 200-ZP-1_PW-1 OU1 at Hanford (56.84 KB) More Documents &

  19. U.S. Department of Energy awards $200 million for next-generation...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    (CORAL) initiative, the U.S. Department of Energy (DOE) announced a 200 million investment to deliver a next-generation supercomputer, known as Aurora, to the Argonne...

  20. 1995 Annual Cathodic Protection Survey Report for the Hanford 200 Area

    SciTech Connect (OSTI)

    Bowman, T.J.

    1996-09-24

    Compilation of the CY 1995 Cathodic Protection Surveys performed for the 200 areas (East Tank Farms, West Tank Farms, Evaporator, PFP, Purex, 222-S Labs).

  1. P300

    Office of Environmental Management (EM)

    0 Satcon Technology Corporation - Proprietary & Confidential Satcon Technology Corporation Request for Information Response for: Addressing Policy and Logistical Challenges to Smart Grid Implementation for US Department of Energy November 1, 2010 Disclosure: Contents found herein are considered proprietary and the distribution of this proposal is restricted to only the corporation stated above. Other requests for copies of this document must be referred to Satcon Headquarters, 27 Drydock

  2. P300

    Office of Environmental Management (EM)

    ... 9.0 DEFINITIONS AND ACRONYMS 9.1 Definitions See LANL Definition of Terms. ... down menu > click on "Advanced Catalog Search" > Enter Course Number in ID box, click on ...

  3. How to program 122,400 heterogeneous cores and retain your sanity

    SciTech Connect (OSTI)

    Patkin, Scott

    2010-01-01

    Current technology trends favor hybrid architectures, typically with each node in a cluster containing both general-purpose and specialized 'accelerator' processors. The typical model for programming such systems is host-centric: The general-purpose processor orchestrates the computation, offloading performance-critical work to the accelerator, and data is communicated only among general-purpose processors. In this talk we propose a radically different hybrid-programming approach, which we call the 'reverse-acceleration model'. In this model the accelerators orchestrate the computation, offloading unacceleratable work to the general-purpose processors. Data is communicated among accelerators, not among general-purpose processors. We present the Cell Messaging Layer (CML), an implementation of the reverse-acceleration model for Los Alamos National Laboratory's Roadrunner supercomputer, a complex conglomerate of 122,400 processor cores of various types, multiple memory domains, and multiple network types, all with radically different performance characteristics but which together make Roadrunner the world's second-fastest supercomputer. CML demonstrates a new messaging-layer implementation technique called 'receiver-initiated message passing', which reduces communication latency by up to a third. Our thesis is that the reverse-acceleration model simplifies porting codes to heterogeneous systems and facilitates performance optimization. We present a case study of a legacy neutron-transport code that we modified to use reverse acceleration. Performance results from running this code across the full Roadrunner system indicate a substantial performance improvement over the unaccelerated version of the code.

  4. Stress corrosion cracking of Ni-Cu alloy 400 tubes in feedwater heaters

    SciTech Connect (OSTI)

    Amar, A.S.

    1994-12-31

    This paper presents the results of the inspections and metallurgical evaluations of a high pressure feedwater heater that experienced numerous tube failures after a short service life. Using EPRI NDE Center technical support, tubes were eddy current tested with special probes in the tubesheet region and with conventional probes in the remaining straight portion. Pulled tubes were metallurgically examined. Crack depths were correlated with eddy current indications. Short axial cracks were found on the inner surface of the tubes at roll transitions. Failures were attributed to intergranular stress corrosion cracking. The cold drawn-stress relieved Monel{trademark} (Alloy 400) tube had < 10 KSI hoop residual stress, however the residual stress was probably much higher in the roll transition. A large number of tubes were plugged based on the eddy current indications, however several tubes that showed no indications had leaked a few months later. This suggested that after initiation, crack growth was rapid. The heater was replaced after 4.5 years of service.

  5. Influence of grain size on the constitutive response and substructure evolution of MONEL 400

    SciTech Connect (OSTI)

    Gray, G.T. III, Chen, S.R.; Vecchio, K.S.

    1999-05-01

    The influence of grain size on the constitutive behavior (strain-rate and temperature dependence of the yield stress and strain hardening) and substructure evolution of MONEL 400 was investigated. Increasing the grain size from 9.5 to 202 {micro}m was seen to reduce the quasi-static yield strength from 290 to 115 MPa, while having a minimal effect on the work-hardening response. Increasing the strain rate from quasi-static to dynamic strain rates (3000 s{sup {minus}1}) was seen to increase the yield and overall flow-stress levels, but has no effect on the strong grain-size dependency exhibited of this alloy. The persistent influence of grain size to large strains is inconsistent with previous d{sup {minus}1/2} pileup grain-size modeling in the literature, which predicts convergence at large strains. Substructure evolution differences between the grain interiors and adjacent to grain boundaries supports differential defect storage processes which are consistent with previously published work-hardening d{sup {minus}1} modeling arguments for grain size-dependent strengthening in polycrystals. The integration of grain-size dependency into constitutive modeling using the mechanical threshold stress (MTS) model is discussed. The MTS model is shown to provide a robust constitutive description capturing yielding, large-strain work hardening, and grain-size effects simultaneously. The MTS model is, additionally, shown to satisfactorily address the experimentally observed transients due to strain-rate or temperature-path dependency.

  6. Planning for the 400,000 tons/year AISI ironmaking demonstration plant

    SciTech Connect (OSTI)

    Aukrust, E. . AISI Direct Steelmaking Program)

    1993-01-01

    The American Iron and Steel Institute (AISI) has formulated a four-year program to design, construct, and operate a 400,000 net ton per year ironmaking demonstration plant. The plant will employ the coal-based ironmaking process developed under a 1989 cooperative agreement with DOE. AISI will manage the design and construction to be completed in the first two years and operate the plant for the second two years with a variety or ores, coals, and fluxes. Campaigns of increasing length are planned to optimize operations. After successful operation, the plant will be taken over by the host company. Results of studies to date indicate that, on a commercial scale, the AISI process will use 27% less energy and have variable operating costs $10 per ton lower and capital costs of $160 per annual ton, compared to the $250 per annual ton rebuild cost for the coke oven-blast furnace process it will replace. The process will enable the domestic steel industry to become more competitive by reducing its capital and operating cost. Furthermore, by eliminating the pollution problems associated with coke production and by completely enclosing the smelting reactions, this process represents a major step towards an environmentally friendly steel industry.

  7. EA-200-B American Electric Power Service Corporation | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    B American Electric Power Service Corporation EA-200-B American Electric Power Service Corporation Order authorizing American Electric Power Service Corporation to export electric power to Canada. EA-200-B American Electric Power Service Corporation (1.84 MB) More Documents & Publications EA-196-B Minnesota Power EA-196-C Minnesota Power EA-243-A Tenaska Power Services Co.

  8. Revised Hydrogeology for the Suprabasalt Aquifer System, 200-West Area and Vicinity, Hanford Site, Washington

    SciTech Connect (OSTI)

    Williams, Bruce A.; Bjornstad, Bruce N.; Schalla, Ronald; Webber, William D.

    2002-05-14

    The primary objective of this study was to refine the conceptual groundwater flow model for the 200-West Area and vicinity. This is the second of two reports that combine to cover the 200 Area Plateau, an area that holds the largest inventory of radionuclide and chemical waste on the Hanford Site.

  9. Development of a 200kW multi-fuel type PAFC power plant

    SciTech Connect (OSTI)

    Take, Tetsuo; Kuwata, Yutaka; Adachi, Masahito; Ogata, Tsutomu

    1996-12-31

    Nippon Telegraph and Telephone Corporation (NFT) has been developing a 200 kW multi-fuel type PAFC power plant which can generate AC 200 kW of constant power by switching fuel from pipeline town gas to liquefied propane gas (LPG) and vice versa. This paper describes the outline of the demonstration test plant and test results of its fundamental characteristics.

  10. Treatability Test Plan for 300 Area Uranium Stabilization through Polyphosphate Injection

    SciTech Connect (OSTI)

    Vermeul, Vincent R.; Williams, Mark D.; Fritz, Brad G.; Mackley, Rob D.; Mendoza, Donaldo P.; Newcomer, Darrell R.; Rockhold, Mark L.; Williams, Bruce A.; Wellman, Dawn M.

    2007-06-01

    The U.S. Department of Energy has initiated a study into possible options for stabilizing uranium at the 300 Area using polyphosphate injection. As part of this effort, PNNL will perform bench- and field-scale treatability testing designed to evaluate the efficacy of using polyphosphate injections to reduced uranium concentrations in the groundwater to meet drinking water standards (30 ug/L) in situ. This technology works by forming phosphate minerals (autunite and apatite) in the aquifer that directly sequester the existing aqueous uranium in autunite minerals and precipitates apatite minerals for sorption and long term treatment of uranium migrating into the treatment zone, thus reducing current and future aqueous uranium concentrations. Polyphosphate injection was selected for testing based on technology screening as part of the 300-FF-5 Phase III Feasibility Study for treatment of uranium in the 300-Area.

  11. The Current and Historical Distribution of Special Status Amphibians at the Livermore Site and Site 300

    SciTech Connect (OSTI)

    Hattem, M V; Paterson, L; Woollett, J

    2008-08-20

    65 surveys were completed in 2002 to assess the current distribution of special status amphibians at the Lawrence Livermore National Laboratory's (LLNL) Livermore Site and Site 300. Combined with historical information from previous years, the information presented herein illustrates the dynamic and probable risk that amphibian populations face at both sites. The Livermore Site is developed and in stark contrast to the mostly undeveloped Site 300. Yet both sites have significant issues threatening the long-term sustainability of their respective amphibian populations. Livermore Site amphibians are presented with a suite of challenges inherent of urban interfaces, most predictably the bullfrog (Rana catesbeiana), while Site 300's erosion issues and periodic feral pig (Sus scrofa) infestations reduce and threaten populations. The long-term sustainability of LLNL's special status amphibians will require active management and resource commitment to maintain and restore amphibian habitat at both sites.

  12. Word Pro - Untitled1

    U.S. Energy Information Administration (EIA) Indexed Site

    Kingdom 569 295 249 160 75 58 49 39 34 30 16 15 Mexico Canada Netherlands Brazil Japan Spain France Italy United Belgium U.S. Virgin South 0 100 200 300 400 500 600 Thousand ...

  13. Texas-Louisiana- Mississippi Salt Basin Greater Green River Basin

    Gasoline and Diesel Fuel Update (EIA)

    Texas-Louisiana- Mississippi Salt Basin Greater Green River Basin W. Gulf Coast Basin ... Major Tight Gas Plays, Lower 48 States 0 200 400 100 300 Miles Source: Energy ...

  14. Slide 1

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    more bandwidth with less power dissipation NVIDIA Fermi 512 cores 2010 Processor - Memory BW Performance 3 0 100 200 300 400 1 10 100 Celeron Athlon Northwood Athlon64X2...

  15. Monthly Performance Report

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    ......... EST-I SITE INFRASTRUCTURE & UTILITIES ... SIU EST FO 3 Month Project Rates TRC 0.00 1.00 2.00 3.00 4.00 Sep-09 Oct-09 Nov-09 Dec-09 ...

  16. Wabuska Aquaculture Low Temperature Geothermal Facility | Open...

    Open Energy Info (EERE)

    erlays":,"markercluster":false,"searchmarkers":"","locations": Hide Map Temperature 132.0 C 270.0 F Flow 1,300 gpm 4,927 Lmin Capacity 4.00x106 Btuhr 1.200 MWt Annual...

  17. Geothermal Regulatory Roadmap

    Broader source: Energy.gov (indexed) [DOE]

    ... Workshop FY12 Project Schedule 7 | US DOE Geothermal Office eere.energy.gov OpenEI (Open Energy Information) 0 100 200 300 400 500 600 700 800 900 1000 Aug-12 Sep-12 Oct-12 Nov-12 ...

  18. Appendix B Surface Infiltration and Aquifer Test Data

    Office of Legacy Management (LM)

    B Surface Infiltration and Aquifer Test Data This page intentionally left blank ... 1000 1100 1200 1300 1400 TIME (MIN) INF-8 TEST I 300 400 TIME (MIN) INF-8 TEST 2 200 250 ...

  19. untitled

    U.S. Energy Information Administration (EIA) Indexed Site

    Operators' Monthly Petroleum Product Sales Report." 0 50 100 150 200 250 300 350 400 J F M A M J J A S O N D 2006 Million Gallons per Day Motor Gasoline No. 2 Distillate...

  20. untitled

    U.S. Energy Information Administration (EIA) Indexed Site

    Plant Operators' Monthly Petroleum Product Sales Report." 50 100 150 200 250 300 350 400 J F M A M J J A S O N D 2008 Cents per Gallon Excluding Taxes Motor Gasoline No. 2...

  1. untitled

    U.S. Energy Information Administration (EIA) Indexed Site

    Operators' Monthly Petroleum Product Sales Report." 0 50 100 150 200 250 300 350 400 J F M A M J J A S O N D 2005 Million Gallons per Day Motor Gasoline No. 2 Distillate...

  2. Denison Dam Historical Generation

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    50,000 100,000 150,000 200,000 250,000 300,000 350,000 400,000 450,000 500,000 (MWh) Denison Dam Historical Generation

  3. C:\\ANNUAL\\Vol2chps.v8\\ANNUAL2.VP

    U.S. Energy Information Administration (EIA) Indexed Site

    in the United States, 1930-2000 Figure 1930 1935 1940 1945 1950 1955 1960 1965 1970 1975 1980 1985 1990 1995 2000 0 5 10 15 20 25 0 100 200 300 400 500 600 700 Trillion Cubic...

  4. Word Pro - Untitled1

    U.S. Energy Information Administration (EIA) Indexed Site

    Million Short Tons 1950 1960 1970 1980 1990 2000 2010 0 300 600 900 Million Short Tons Surface 1950 1960 1970 1980 1990 2000 2010 0 200 400 600 800 Million Short Tons Underground ...

  5. VanDoc_135908_1

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    ... Market for New Coal Power Plant Technology 0 50 100 150 200 250 300 350 400 2000 2005 2010 2015 2020 2025 2030 2035 2040 2045 2050 Coal-Fired Plant Capacity (GW) EIA Projected Coal ...

  6. State Energy Advisory Board Meeting Update and Overview of Renewable...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    change from Q1 2012 0 100 200 300 400 500 CHP Coal fired Natural gas CCGT Nuclear Small hydro Large hydro Geothermal - flash plant Wind - onshore Municipal solid waste Landfill ...

  7. The Market for Coal Based Electric Power Generation

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    ... Market for New Coal Power Plant Technology 0 50 100 150 200 250 300 350 400 2000 2005 2010 2015 2020 2025 2030 2035 2040 2045 2050 Coal-Fired Plant Capacity (GW) EIA Projected Coal ...

  8. 300 Area dangerous waste tank management system: Compliance plan approach. Final report

    SciTech Connect (OSTI)

    1996-03-01

    In its Dec. 5, 1989 letter to DOE-Richland (DOE-RL) Operations, the Washington State Dept. of Ecology requested that DOE-RL prepare ``a plant evaluating alternatives for storage and/or treatment of hazardous waste in the 300 Area...``. This document, prepared in response to that letter, presents the proposed approach to compliance of the 300 Area with the federal Resource Conservation and Recovery Act and Washington State`s Chapter 173-303 WAC, Dangerous Waste Regulations. It also contains 10 appendices which were developed as bases for preparing the compliance plan approach. It refers to the Radioactive Liquid Waste System facilities and to the radioactive mixed waste.

  9. Elimination of Heat-Shielding for Geothermal Tools Operating Up To 300 Degress Celsius

    SciTech Connect (OSTI)

    HENFLING,JOSEPH A.; NORMANN,RANDY A.

    1999-10-07

    This report focuses Sandia National Laboratories' effort to create high-temperature logging tools for geothermal applications not requiring heat-shielding. Tool electronics can operate up to 300 C with a few limiting components operating to 250 C. Second generation electronics are needed to increase measurement accuracy and extend the operating range to 300 and then 350 C are identified. Custom development of high-temperature batteries and assembling techniques are touched on. Outcomes of this work are discussed and new directions for developing high-temperature industry are suggested.

  10. Dynamic tensile characterization of Vascomax® maraging C250 and C300 alloys

    SciTech Connect (OSTI)

    Song, Bo; Wakeland, Peter Eric; Furnish, Michael D.

    2015-04-14

    Vascomax® maraging C250 and C300 alloys were dynamically characterized in tension with Kolsky tension bar techniques. Compared with conventional Kolsky tension bar experiments, a pair of lock nuts was used to minimize the pseudo stress peak and a laser system was applied to directly measure the specimen displacement. Dynamic engineering stress–strain curves of the C250 and C300 alloys were obtained in tension at 1000 and 3000 s–1. The dynamic yield strengths for both alloys were similar, but significantly higher than those obtained from quasi-static indentation tests. Both alloys exhibited insignificant strain-rate effect on dynamic yield strength. The C300 alloy showed approximately 10 % higher in yield strength than the C250 alloy at the same strain rates. Necking was observed in both alloys right after yield. The Bridgman correction was applied to calculate the true stress and strain at failure for both alloys. The true failure stress showed a modest strain rate effect for both alloys but no significant difference between the two alloys at the same strain rate. As a result, the C250 alloy was more ductile than the C300 alloy under dynamic loading.

  11. Dynamic tensile characterization of Vascomax® maraging C250 and C300 alloys

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Song, Bo; Wakeland, Peter Eric; Furnish, Michael D.

    2015-04-14

    Vascomax® maraging C250 and C300 alloys were dynamically characterized in tension with Kolsky tension bar techniques. Compared with conventional Kolsky tension bar experiments, a pair of lock nuts was used to minimize the pseudo stress peak and a laser system was applied to directly measure the specimen displacement. Dynamic engineering stress–strain curves of the C250 and C300 alloys were obtained in tension at 1000 and 3000 s–1. The dynamic yield strengths for both alloys were similar, but significantly higher than those obtained from quasi-static indentation tests. Both alloys exhibited insignificant strain-rate effect on dynamic yield strength. The C300 alloy showedmore » approximately 10 % higher in yield strength than the C250 alloy at the same strain rates. Necking was observed in both alloys right after yield. The Bridgman correction was applied to calculate the true stress and strain at failure for both alloys. The true failure stress showed a modest strain rate effect for both alloys but no significant difference between the two alloys at the same strain rate. As a result, the C250 alloy was more ductile than the C300 alloy under dynamic loading.« less

  12. The 300 Area Integrated Field Research Challenge Quality Assurance Project Plan

    SciTech Connect (OSTI)

    Fix, N. J.

    2009-04-29

    Pacific Northwest National Laboratory and a group of expert collaborators are using the U.S. Department of Energy Hanford Site 300 Area uranium plume within the footprint of the 300-FF-5 groundwater operable unit as a site for an Integrated Field-Scale Subsurface Research Challenge (IFRC). The IFRC is entitled Multi-Scale Mass Transfer Processes Controlling Natural Attenuation and Engineered Remediation: An IFRC Focused on the Hanford Site 300 Area Uranium Plume Project. The theme is investigation of multi-scale mass transfer processes. A series of forefront science questions on mass transfer are posed for research that relate to the effect of spatial heterogeneities; the importance of scale; coupled interactions between biogeochemical, hydrologic, and mass transfer processes; and measurements/approaches needed to characterize and model a mass transfer-dominated system. This Quality Assurance Project Plan provides the quality assurance requirements and processes that will be followed by the 300 Area IFRC Project. This plan is designed to be used exclusively by project staff.

  13. Remedial investigation and feasibility study for the Lawrence Livermore National Laboratory Site 300 Pit 7 Complex

    SciTech Connect (OSTI)

    Taffet, M.J. ); Oberdorfer, J.A. ); McIlvride, W.A. )

    1989-10-01

    This report summarizes the results and conclusions of the investigation of tritium and other compounds in ground water in the vicinity of landfills at the Lawrence Livermore National Laboratory (LLNL) Site 300 Pit 7 Complex. 91 refs., 110 figs., 43 tabs.

  14. 100 Area and 300 Area Component of the RCBRA Fall 2005 Data Compilation

    SciTech Connect (OSTI)

    J.M. Queen

    2006-05-30

    The purpose of this report is to provide a brief description of the sampling approaches, a description of the samples collected, and the results for the Fall 2005 sampling event. This report presents the methods and results of the work to support the 100 Area and 300 Area Component of the River Corridor Baseline Risk Assessment.

  15. 300 Area D4 Project Fiscal Year 2007 Building Completion Report

    SciTech Connect (OSTI)

    R. A. Westberg

    2009-01-15

    This report documents the deactivation, decontamination, decommissioning, and demolition (D4) of twenty buildings in the 300 Area of the Hanford Site. The D4 of these facilties included characterization, engineering, removal of hazardous and radiologically contaminated materials, equipment removal, utility disconnection, deactivation, decontamination, demolition of the structure, and stabilization or removal of the remaining slab and foundation, as appropriate.

  16. 300 Area D4 Project 3rd Quarter Fiscal Year 2006 Building Completion Report

    SciTech Connect (OSTI)

    D. S. Smith

    2006-09-25

    This report documents the deactivation, decontamination, decommissioning, and demolition of five buildings in the 300 Area of the Hanford Site. The D4 of these facilities included characterization, engineering, removal of hazardous and radiologically contaminated materials, equipment removal, utility disconnection, deactivation, decontamination, demolition of the structure, and stabilization or removal of the remaining slab and foundation as appropriate.

  17. 300°C Capable Electronics Platform and Temperature Sensor System For Enhanced Geothermal Systems

    Broader source: Energy.gov [DOE]

    Project objectives: Enable geothermal wellbore monitoring through the development of SiC based electronics and ceramic packaging capable of sustained operation at temperatures up to 300˚C and 10 km depth. Demonstrate the technology with a temperature sensor system.

  18. 300 Area D4 Project 2nd Quarter FY06 Building Completion Report

    SciTech Connect (OSTI)

    David S. Smith

    2006-06-26

    This report documents the deactivation, decontamination, decommissioning, and demolition of 16 buildings in the 300 Area of the Hanford Site. The D4 of these facilities included characterization, engineering, removal of hazardous and radiologically contaminated materials, equipment removal, utility disconnection, deactivation, decontamination, demolition of the structure, and stabilization or removal of the remaining slab and foundation as appropriate.

  19. Vice President Biden Announces 200,000 Homes Weatherized Under the Recovery

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Act | Department of Energy 200,000 Homes Weatherized Under the Recovery Act Vice President Biden Announces 200,000 Homes Weatherized Under the Recovery Act August 26, 2010 - 12:00am Addthis Manchester, N.H. - At an event with homeowners and workers who benefited from the program, today in Manchester, New Hampshire, Vice President Joe Biden announced a major Recovery Act milestone - the weatherizing of 200,000 homes under the Recovery Act. As a result of the Administration's unprecedented

  20. Summary - Remedial System Performance Improvement for the 200-ZP-1_PW-1 OU1 at Hanford

    Office of Environmental Management (EM)

    200-ZP-1/PW-1 Operable Units ETR Report Date: February 2007 ETR-5 United States Department of Energy Office of Environmental Management (DOE-EM) External Technical Review Remedial System Performance Improvement for the 200-ZP-1/PW-1 Operable Units at Hanford Why DOE-EM Did This Review The 200-ZP-1 OU and PW-1 OU are pump and treat operating units (OU) designed to remove carbon tetrachloride (CT) from the groundwater and vadose zone, respectively. The units support a Comprehensive Environmental

  1. Fact #926: May 23, 2016 Petroleum Imports Below $200 Billion, Lowest Point

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    in Over a Decade - Dataset | Department of Energy 6: May 23, 2016 Petroleum Imports Below $200 Billion, Lowest Point in Over a Decade - Dataset Fact #926: May 23, 2016 Petroleum Imports Below $200 Billion, Lowest Point in Over a Decade - Dataset Excel file and dataset for Petroleum Imports Below $200 Billion, Lowest Point in Over a Decade fotw#926_web.xlsx (23.51 KB) More Documents & Publications Fact #897: November 2, 2015 Fuel Wasted in Traffic Congestion - Dataset Project Reports for

  2. DOE Announces up to $200 Million in Funding for Biorefineries | Department

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    of Energy up to $200 Million in Funding for Biorefineries DOE Announces up to $200 Million in Funding for Biorefineries May 1, 2007 - 12:45pm Addthis Small- and full-scale projects total up to $585 million to advance President Bush's Twenty in Ten Initiative WASHINGTON, DC - U.S. Department of Energy (DOE) Secretary Samuel W. Bodman today announced that DOE will provide up to $200 million, over five years (FY'07-'11) to support the development of small-scale cellulosic biorefineries in the

  3. 200,000 Homes Weatherized Under the Recovery Act -- Video from Cathy Zoi |

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Department of Energy 0,000 Homes Weatherized Under the Recovery Act -- Video from Cathy Zoi 200,000 Homes Weatherized Under the Recovery Act -- Video from Cathy Zoi August 26, 2010 - 4:51pm Addthis Cathy Zoi, Assistant Secretary for Energy Efficiency and Renewable Energy, shares her thoughts on reaching the 200,000 weatherized homes milestone. Andy Oare Andy Oare Former New Media Strategist, Office of Public Affairs Today Vice President Biden announced that 200,000 homes have been

  4. Title 18 CFR 4.200 et seq. Application for Amendment of License...

    Open Energy Info (EERE)

    OpenEI Reference LibraryAdd to library Legal Document- RegulationRegulation: Title 18 CFR 4.200 et seq. Application for Amendment of LicenseLegal Abstract Regulations providing for...

  5. Take Marine Mammals Permit Application Form 3-200-43 | Open Energy...

    Open Energy Info (EERE)

    to library Form: Take Marine Mammals Permit Application Form 3-200-43 Abstract Federal Fish and Wildlife permit application form for take TakeImportTransportExport of Marine...

  6. Take of Eagles Permit 3-200-16 | Open Energy Information

    Open Energy Info (EERE)

    Reference LibraryAdd to library Form: Take of Eagles Permit 3-200-16 Abstract Federal Fish and Wildlife Permit Application Form for Take of Depredating Eagles and Eagles that...

  7. Title 32 CFR 651 Environmental Analysis of Army Actions (AR 200...

    Open Energy Info (EERE)

    of Army Actions (AR 200-2) Jump to: navigation, search OpenEI Reference LibraryAdd to library Legal Document- Federal RegulationFederal Regulation: Title 32 CFR 651...

  8. Department of Energy (DOE) O 200.1A Information Technology Management...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    M 205.1-6 Media Sanitization Manual Department of Energy (DOE) O 200.1A Information Technology Management DOE M 205.1-6 Media Sanitization Manual PF2009-14.pdf (384.38 KB) More ...

  9. Waste status and transaction record summary for the northwest quadrant of the Hanford 200 Area

    SciTech Connect (OSTI)

    Agnew, S.F.; Corbin, R.A.; Duran, T.B.; Jurgensen, K.A.; Ortiz, T.P.; Young, B.L.

    1995-09-01

    This supporting document contains a database of waste transactions and waste status reports for all the waste tanks in the northwest quadrant of the 200 West Area of the Hanford Site.

  10. DOE Moab Site Cost-Effectively Eliminates 200 Million Gallons of Contaminated Ground Water

    Broader source: Energy.gov [DOE]

    Grand Junction, CO ― The Department of Energy (DOE) announced today that it has extracted 200 million gallons of contaminated ground water from the Moab site in Utah as part of the Moab Uranium Mill Tailings Remedial Action Project.

  11. Statement of Work for Drilling Four CERCLA Groundwater Monitoring Wells During Fiscal Year 2006, 300-FF-5 Operable Unit

    SciTech Connect (OSTI)

    Williams, Bruce A.

    2005-10-10

    This document contains the statement of work required to drill, characterize, and construct the proposed groundwater monitoring wells at 300-FF-5 Operable Unit during FY 2006.

  12. Ultra Energy Efficient Data Center Saves NREL $200,000 | Department of

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Energy Ultra Energy Efficient Data Center Saves NREL $200,000 Ultra Energy Efficient Data Center Saves NREL $200,000 November 14, 2011 - 5:08pm Addthis The National Renewable Energy Laboratory's (NREL) Data Center marks a significant accomplishment in its ultra-efficiency. | Video courtesy of NREL. National Renewable Energy Laboratory (NREL) Technician Mic Stremel works with a blade server in the green data center at the Research Support Facility. | Image courtesy of NREL, Dennis Schroeder.

  13. DOE Announces Funding Opportunity of up to $200 Million for Pilot and

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Demonstration Scale Biorefinery Projects | Department of Energy Opportunity of up to $200 Million for Pilot and Demonstration Scale Biorefinery Projects DOE Announces Funding Opportunity of up to $200 Million for Pilot and Demonstration Scale Biorefinery Projects December 22, 2008 - 8:51am Addthis Projects Will Demonstrate Continued Commitment to Develop Sustainable, Cost-Competitive Advanced Biofuels WASHINGTON - The U.S. Department of Energy (DOE) today announced the issuance of a Funding

  14. U.S. Department of Energy Awards $200 Million for Next- Generation

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Supercomputer at Argonne National Laboratory | Department of Energy Awards $200 Million for Next- Generation Supercomputer at Argonne National Laboratory U.S. Department of Energy Awards $200 Million for Next- Generation Supercomputer at Argonne National Laboratory April 9, 2015 - 12:29pm Addthis Under Secretary for Science and Energy Orr Announces Next Steps in Pursuit of Exascale Supercomputing to Accelerate Major Scientific Discoveries and Engineering Breakthroughs. Argonne, Ill. - Today,

  15. Search for Neutrinoless Double-Beta Decay in $^{136}$Xe with EXO-200

    Office of Scientific and Technical Information (OSTI)

    (Journal Article) | SciTech Connect Journal Article: Search for Neutrinoless Double-Beta Decay in $$^{136}$$Xe with EXO-200 Citation Details In-Document Search Title: Search for Neutrinoless Double-Beta Decay in $$^{136}$$Xe with EXO-200 Authors: Auger, M. ; /Bern U. ; Auty, D.J. ; /Alabama U. ; Barbeau, P.S. ; /Stanford U., Phys. Dept. ; Beauchamp, E. ; /Laurentian U. ; Belov, V. ; /Moscow, ITEP ; Benitez-Medina, C. ; /Colorado State U. ; Breidenbach, M. ; /SLAC ; Brunner, T. ; /Stanford

  16. More Than 200 DOE Safety and Health Trainers Gather for Exchange |

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Department of Energy More Than 200 DOE Safety and Health Trainers Gather for Exchange More Than 200 DOE Safety and Health Trainers Gather for Exchange April 29, 2015 - 12:00pm Addthis HAMMER Program Manager Thom Hogg discusses radiological monitoring during a National Training Center event and NIEHS Worker Trainer’s Exchange near the Hanford Site. HAMMER Program Manager Thom Hogg discusses radiological monitoring during a National Training Center event and NIEHS Worker Trainer's

  17. Lawrence Livermore National Laboratory (LLNL) Experimental Test Site (Site 300) Salinity Evaluation and Minimization Plan for Cooling Towers and Mechanical Equipment Discharges

    SciTech Connect (OSTI)

    Daily III, W D

    2010-02-24

    This document was created to comply with the Central Valley Regional Water Quality Control Board (CVRWQCB) Waste Discharge Requirement (Order No. 98-148). This order established new requirements to assess the effect of and effort required to reduce salts in process water discharged to the subsurface. This includes the review of technical, operational, and management options available to reduce total dissolved solids (TDS) concentrations in cooling tower and mechanical equipment water discharges at Lawrence Livermore National Laboratory's (LLNL's) Experimental Test Site (Site 300) facility. It was observed that for the six cooling towers currently in operation, the total volume of groundwater used as make up water is about 27 gallons per minute and the discharge to the subsurface via percolation pits is 13 gallons per minute. The extracted groundwater has a TDS concentration of 700 mg/L. The cooling tower discharge concentrations range from 700 to 1,400 mg/L. There is also a small volume of mechanical equipment effluent being discharged to percolation pits, with a TDS range from 400 to 3,300 mg/L. The cooling towers and mechanical equipment are maintained and operated in a satisfactory manner. No major leaks were identified. Currently, there are no re-use options being employed. Several approaches known to reduce the blow down flow rate and/or TDS concentration being discharged to the percolation pits and septic systems were reviewed for technical feasibility and cost efficiency. These options range from efforts as simple as eliminating leaks to implementing advanced and innovative treatment methods. The various options considered, and their anticipated effect on water consumption, discharge volumes, and reduced concentrations are listed and compared in this report. Based on the assessment, it was recommended that there is enough variability in equipment usage, chemistry, flow rate, and discharge configurations that each discharge location at Site 300 should be

  18. DESCRIPTION OF MODELING ANALYSES IN SUPPORT OF THE 200-ZP-1 REMEDIAL DESIGN/REMEDIAL ACTION

    SciTech Connect (OSTI)

    VONGARGEN BH

    2009-11-03

    The Feasibility Study/or the 200-ZP-1 Groundwater Operable Unit (DOE/RL-2007-28) and the Proposed Plan/or Remediation of the 200-ZP-1 Groundwater Operable Unit (DOE/RL-2007-33) describe the use of groundwater pump-and-treat technology for the 200-ZP-1 Groundwater Operable Unit (OU) as part of an expanded groundwater remedy. During fiscal year 2008 (FY08), a groundwater flow and contaminant transport (flow and transport) model was developed to support remedy design decisions at the 200-ZP-1 OU. This model was developed because the size and influence of the proposed 200-ZP-1 groundwater pump-and-treat remedy will have a larger areal extent than the current interim remedy, and modeling is required to provide estimates of influent concentrations and contaminant mass removal rates to support the design of the aboveground treatment train. The 200 West Area Pre-Conceptual Design/or Final Extraction/Injection Well Network: Modeling Analyses (DOE/RL-2008-56) documents the development of the first version of the MODFLOW/MT3DMS model of the Hanford Site's Central Plateau, as well as the initial application of that model to simulate a potential well field for the 200-ZP-1 remedy (considering only the contaminants carbon tetrachloride and technetium-99). This document focuses on the use of the flow and transport model to identify suitable extraction and injection well locations as part of the 200 West Area 200-ZP-1 Pump-and-Treat Remedial Design/Remedial Action Work Plan (DOEIRL-2008-78). Currently, the model has been developed to the extent necessary to provide approximate results and to lay a foundation for the design basis concentrations that are required in support of the remedial design/remediation action (RD/RA) work plan. The discussion in this document includes the following: (1) Assignment of flow and transport parameters for the model; (2) Definition of initial conditions for the transport model for each simulated contaminant of concern (COC) (i.e., carbon

  19. Toward petascale computing in geosciences: application to the Hanford 300 Area

    SciTech Connect (OSTI)

    Hammond, Glenn E.; Lichtner, Peter C.; Mills, Richard T.; Lu, Chuan

    2008-09-01

    Modeling uranium transport at the Hanford 300 Area presents new challenges for high performance computing. A field-scale three-dimensional domain with an hourly fluctuating Columbia river stage coupled to flow in highly permeable sediments results in fast groundwater flow rates requiring small time steps. In this work, high-performance computing has been applied to simulate variably saturated groundwater flow and tracer transport at the 300 Area using PFLOTRAN. Simulation results are presented for discretizations up to 10.8 million degrees of freedom, while PFLOTRAN performance was assessed on up to one billion degrees of freedom and 12,000 processor cores on Jaguar, the Cray XT4 supercomputer at ORNL.

  20. Toward petascale computing in geosciences: application to the Hanford 300 area

    SciTech Connect (OSTI)

    Hammond, Glenn; Lichtner, Peter; Mills, Richard T; Lu, Chuan

    2008-01-01

    Modeling uranium transport at the Hanford 300 Area presents new challenges for high performance computing. A field-scale three-dimensional domain with an hourly fluctuating Columbia river stage coupled to flow in highly permeable sediments results in fast groundwater flow rates requiring small time steps. In this work, high-performance computing has been applied to simulate variably saturated groundwater flow and tracer transport at the 300 Area using PFLOTRAN. Simulation results are presented for discretizations up to 10.8 million degrees of freedom, while PFLOTRAN performance was assessed on up to one billion degrees of freedom and 12,000 processor cores on Jaguar, the Cray XT4 supercomputer at ORNL.

  1. Hazard analysis for 300 Area N Reactor Fuel Fabrication and Storage Facilty

    SciTech Connect (OSTI)

    Johnson, D.J.; Brehm, J.R.

    1994-01-25

    This hazard analysis (HA) has been prepared for the 300 Area N Reactor Fuel Fabrication and Storage Facility (Facility), in compliance with the requirements of Westinghouse Hanford Company (Westinghouse Hanford) controlled manual WHC-CM-4-46, Nonreactor Facility Safety Analysis Manual, and to the direction of WHC-IP-0690, Safety Analysis and Regulation Desk Instructions, (WHC 1992). An HA identifies potentially hazardous conditions in a facility and the associated potential accident scenarios. Unlike the Facility hazard classification documented in WHC-SD-NR-HC-004, Hazard Classification for 300 Area N Reactor Fuel Fabrication and Storage Facility, (Huang 1993), which is based on unmitigated consequences, credit is taken in an HA for administrative controls or engineered safety features planned or in place. The HA is the foundation for the accident analysis. The significant event scenarios identified by this HA will be further evaluated in a subsequent accident analysis.

  2. Secretary Chu Announces Nearly $300 Million in Clean Cities Grants to

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Support Clean Fuels, Vehicles, and Infrastructure Development | Department of Energy in Clean Cities Grants to Support Clean Fuels, Vehicles, and Infrastructure Development Secretary Chu Announces Nearly $300 Million in Clean Cities Grants to Support Clean Fuels, Vehicles, and Infrastructure Development August 26, 2009 - 12:00am Addthis WASHINGTON, DC - Energy Secretary Steven Chu today announced the selection of 25 cost-share projects under the Clean Cities program that will be funded with

  3. Uranium Contamination in the Subsurface Beneath the 300 Area, Hanford Site, Washington

    SciTech Connect (OSTI)

    Peterson, Robert E.; Rockhold, Mark L.; Serne, R. Jeffrey; Thorne, Paul D.; Williams, Mark D.

    2008-02-29

    This report provides a description of uranium contamination in the subsurface at the Hanford Site's 300 Area. The principal focus is a persistence plume in groundwater, which has not attenuated as predicted by earlier remedial investigations. Included in the report are chapters on current conditions, hydrogeologic framework, groundwater flow modeling, and geochemical considerations. The report is intended to describe what is known or inferred about the uranium contamination for the purpose of making remedial action decisions.

  4. Borehole Completion and Conceptual Hydrogeologic Model for the IFRC Well Field, 300 Area, Hanford Site

    SciTech Connect (OSTI)

    Bjornstad, Bruce N.; Horner, Jacob A.; Vermeul, Vincent R.; Lanigan, David C.; Thorne, Paul D.

    2009-04-20

    A tight cluster of 35 new wells was installed over a former waste site, the South Process Pond (316-1 waste site), in the Hanford Site 300 Area in summer 2008. This report documents the details of the drilling, sampling, and well construction for the new array and presents a summary of the site hydrogeology based on the results of drilling and preliminary geophysical logging.

  5. Microsoft PowerPoint - Hanford_Reach_Natl_Monument_300 sq.ppt [Compatibility Mode]

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Reach National Monument The Hanford Reach National Monument encompasses 300 square miles around the Hanford Site Part of the effort to reduce the active around the Hanford Site. Part of the effort to reduce the active footprint of the site involves cleanup of debris sites on Rattlesnake Mountain and the Fitzner-Eberhardt Arid Lands Ecology Reserve. The Hanford Reach was protected by Presidential proclamation in 2000 Hanford Reach was protected by Presidential proclamation in 2000. Past military

  6. 300 Area D4 Project Fiscal Year 2009 Building Completion Report

    SciTech Connect (OSTI)

    B. J. Skwarek

    2010-01-27

    This report summarizes the deactivation, decontamination, decommissioning, and demolition activities of seven facilities in the 300 Area of the Hanford Site in fiscal year 2009. The D4 of these facilities included characterization; engineering; removal of hazardous and radiologically contaminated materials; equipment removal; utility disconnection; deactivation, decontamination, demolition of the structure; and stabilization or removal of slabs and foundations. This report also summarizes the nine below-grade slabs/foundations removed in FY09 of buildings demolished in previous fiscal years.

  7. 300 Area D4 Project Fiscal Year 2008 Building Completion Report

    SciTech Connect (OSTI)

    R. A. Westberg

    2009-01-15

    This report documents the deactivation, decontamination, decommissioning, and demolition (D4) of eighteen buildings in the 300 Area of the Hanford Site that were demolished in Fiscal Year 2008. The D4 of these facilties included characterization, engineering, removal of hazardous and radiologically contaminated materials, equipment removal, utility disconnection, deactivation, decontamination, demolition of the structure, and stabilization or removal of the remaining slab and foundation, as appropriate.

  8. Flow and Transport in the Hanford 300 Area Vadose Zone-Aquifer-River System

    SciTech Connect (OSTI)

    Waichler, Scott R.; Yabusaki, Steven B.

    2005-07-13

    Contaminant migration in the 300 Area unconfined aquifer is strongly coupled to fluctuations in the Columbia River stage. To better understand the interaction between the river, aquifer, and vadose zone, a 2-D saturated-unsaturated flow and transport model was developed for a vertical cross-section aligned west-east across the Hanford Site 300 Area, nearly perpendicular to the river. The model was used to investigate water flow and tracer transport in the vadose zone-aquifer-river flow system, in support of the ongoing study of the 300 Area uranium plume. The STOMP simulator was used to model 1-year from 3/1/92 to 2/28/93, a period when hourly data were available for both groundwater and river levels. Net water flow to the river (per 1-meter width of shoreline) was 182 m3/y in the base case, but the cumulative exchange or total flow back and forth across the riverbed was 30 times greater. The low river case had approximately double the net water and Groundwater tracer flux into the river as compared to the base case.

  9. Site safety plan for Lawrence Livermore National Laboratory CERCLA investigations at site 300. Revision 2

    SciTech Connect (OSTI)

    Kilmer, J.

    1997-08-01

    Various Department of Energy Orders incorporate by reference, health and safety regulations promulgated by the Occupational Safety and Health Administration (OSHA). One of the OSHA regulations, 29 CFR 1910.120, Hazardous Waste Operations and Emergency Response, requires that site safety plans are written for activities such as those covered by work plans for Site 300 environmental investigations. Based upon available data, this Site Safety Plan (Plan) for environmental restoration has been prepared specifically for the Lawrence Livermore National Laboratory Site 300, located approximately 15 miles east of Livermore, California. As additional facts, monitoring data, or analytical data on hazards are provided, this Plan may need to be modified. It is the responsibility of the Environmental Restoration Program and Division (ERD) Site Safety Officer (SSO), with the assistance of Hazards Control, to evaluate data which may impact health and safety during these activities and to modify the Plan as appropriate. This Plan is not `cast-in-concrete.` The SSO shall have the authority, with the concurrence of Hazards Control, to institute any change to maintain health and safety protection for workers at Site 300.

  10. Current Conditions Risk Assessment for the 300-FF-5 Groundwater Operable Unit

    SciTech Connect (OSTI)

    Miley, Terri B.; Bunn, Amoret L.; Napier, Bruce A.; Peterson, Robert E.; Becker, James M.

    2007-11-01

    This report updates a baseline risk assessment for the 300 Area prepared in 1994. The update includes consideration of changes in contaminants of interest and in the environment that have occurred during the period of interim remedial action, i.e., 1996 to the present, as well as the sub-regions, for which no initial risk assessments have been conducted. In 1996, a record of decision (ROD) stipulated interim remedial action for groundwater affected by releases from 300 Area sources, as follows: (a) continued monitoring of groundwater that is contaminated above health-based levels to ensure that concentrations continue to decrease, and (b) institutional controls to ensure that groundwater use is restricted to prevent unacceptable exposure to groundwater contamination. In 2000, the groundwater beneath the two outlying sub-regions was added to the operable unit. In 2001, the first 5-year review of the ROD found that the interim remedy and remedial action objectives were still appropriate, although the review called for additional characterization activities. This report includes a current conditions baseline ecological and human health risk assessment using maximum concentrations in the environmental media of the 300-FF-5 Operable Unit and downstream conditions at the City of Richland, Washington. The scope for this assessment includes only current measured environmental concentrations and current use scenarios. Future environmental concentrations and future land uses are not considered in this assessment.

  11. Minimum separation distances for natural gas pipeline and boilers in the 300 area, Hanford Site

    SciTech Connect (OSTI)

    Daling, P.M.; Graham, T.M.

    1997-08-01

    The U.S. Department of Energy (DOE) is proposing actions to reduce energy expenditures and improve energy system reliability at the 300 Area of the Hanford Site. These actions include replacing the centralized heating system with heating units for individual buildings or groups of buildings, constructing a new natural gas distribution system to provide a fuel source for many of these units, and constructing a central control building to operate and maintain the system. The individual heating units will include steam boilers that are to be housed in individual annex buildings located at some distance away from nearby 300 Area nuclear facilities. This analysis develops the basis for siting the package boilers and natural gas distribution systems to be used to supply steam to 300 Area nuclear facilities. The effects of four potential fire and explosion scenarios involving the boiler and natural gas pipeline were quantified to determine minimum separation distances that would reduce the risks to nearby nuclear facilities. The resulting minimum separation distances are shown in Table ES.1.

  12. Isotopic Tracking of Hanford 300 Area Derived Uranium in the Columbia River

    SciTech Connect (OSTI)

    Christensen, John N.; Dresel, P. Evan; Conrad, Mark E.; Patton, Gregory W.; DePaolo, Donald J.

    2010-10-31

    Our objectives in this study are to quantify the discharge rate of uranium (U) to the Columbia River from the Hanford Site's 300 Area, and to follow that U down river to constrain its fate. Uranium from the Hanford Site has variable isotopic composition due to nuclear industrial processes carried out at the site. This characteristic makes it possible to use high-precision isotopic measurements of U in environmental samples to identify even trace levels of contaminant U, determine its sources, and estimate discharge rates. Our data on river water samples indicate that as much as 3.2 kg/day can enter the Columbia River from the 300 Area, which is only a small fraction of the total load of dissolved natural background U carried by the Columbia River. This very low-level of Hanford derived U can be discerned, despite dilution to < 1 percent of natural background U, 350 km downstream from the Hanford Site. These results indicate that isotopic methods can allow the amounts of U from the 300 Area of the Hanford Site entering the Columbia River to be measured accurately to ascertain whether they are an environmental concern, or are insignificant relative to natural uranium background in the Columbia River.

  13. Department of Energy Awards $200,000 Grant to the Savannah River Regional Diversification Initiative Community Reuse Organization

    Broader source: Energy.gov [DOE]

    Department of Energy Awards $200,000 Grant to the Savannah River Regional Diversification Initiative Community Reuse Organization

  14. I'll Take Argonne for $200, Alex | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    I'll Take Argonne for $200, Alex I'll Take Argonne for $200, Alex March 10, 2011 - 2:20pm Addthis Charles Rousseaux Charles Rousseaux Senior Communications Specialist (detailee) Argonne National Laboratory is one of the nation's oldest and largest national labs, where more than 3,000 employees do basic and applied research in virtually every scientific disciple. Argonne will also be featured as a question category on Jeopardy! tonight (check your local listings). Quick! Who is the only physicist

  15. Fact #926: May 23, 2016 Petroleum Imports Below $200 Billion, Lowest Point

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    in Over a Decade | Department of Energy 6: May 23, 2016 Petroleum Imports Below $200 Billion, Lowest Point in Over a Decade Fact #926: May 23, 2016 Petroleum Imports Below $200 Billion, Lowest Point in Over a Decade SUBSCRIBE to the Fact of the Week Petroleum exports were rising in 2015 and petroleum imports held fairly steady at just over 9 million barrels per day, but the value of those imports and exports was significantly lower than the previous year. The falling cost of a barrel of oil

  16. Geothermal Heat Pump System for the New 500-bed 200,000 SF Student Housing

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Project at the University at Albanys Main Campus | Department of Energy Heat Pump System for the New 500-bed 200,000 SF Student Housing Project at the University at Albanys Main Campus Geothermal Heat Pump System for the New 500-bed 200,000 SF Student Housing Project at the University at Albanys Main Campus This project proposes to heat and cool planned 500-bed apartment-style student housing with closed loop vertical bore geothermal heat pump system installation.

  17. Type A Accident Investigation of the July 15, 2004, Hanford 200 East Area

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Fall Fatality | Department of Energy July 15, 2004, Hanford 200 East Area Fall Fatality Type A Accident Investigation of the July 15, 2004, Hanford 200 East Area Fall Fatality August 1, 2004 On the morning of Thursday, July 15, 2004, a non-government contractor employee of All Mobile Transporting & Repairs (AMTR) was found motionless at the bottom of a ladder with a serious head injury. It was believed the employee had been standing on the ladder, using a battery-powered drill, to remove

  18. DOE to Remove 200 Metric Tons of Highly Enriched Uranium from U.S. Nuclear

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Weapons Stockpile | Department of Energy to Remove 200 Metric Tons of Highly Enriched Uranium from U.S. Nuclear Weapons Stockpile DOE to Remove 200 Metric Tons of Highly Enriched Uranium from U.S. Nuclear Weapons Stockpile November 7, 2005 - 12:38pm Addthis Will Be Redirected to Naval Reactors, Down-blended or Used for Space Programs WASHINGTON, DC - Secretary of Energy Samuel W. Bodman today announced that the Department of Energy's (DOE) National Nuclear Security Administration (NNSA) will

  19. Upgrading a high-throughput spectrometer for high-frequency (&lt;400 kHz) measurements

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Upgrading a high-throughput spectrometer for high-frequency ( T. Nishizawa, M. D. Nornberg, D. J. Den Hartog, and D. Craig Citation: Review of Scientific Instruments 87, 11E530 (2016); doi: 10.1063/1.4960073 View online: http://dx.doi.org/10.1063/1.4960073 View Table of Contents: http://scitation.aip.org/content/aip/journal/rsi/87/11?ver=pdfcov Published by the AIP Publishing Articles you may be interested in Observation of 20-400 kHz fluctuations in the U-3M torsatron Phys. Plasmas 23, 022506

  20. Literature Review on the Effects of Prescription Fire on theEcology of Site 300

    SciTech Connect (OSTI)

    Preston, R

    2011-03-14

    Lawrence Livermore National Laboratory has historically conducted prescription burns across approximately 2,000 acres of Site 300 on an annual basis to safeguard test facilities and operations from the risk of wildfire encroachment. Prescription burns began in 1960, and although fire frequency varies among the designated burn areas, all have been burned at least once. A patchwork of native perennial grassland communities and associated special-status plant and animal populations occur onsite in many areas that have been receiving these treatments. Because the size and locations of prescription burns may shift in coming years, an evaluation is warranted to determine how these shifts may affect listed biota, including rare plants, and the distinct ecological conditions present on the site. This report presents the results of a literature review conducted by ICF International (ICF) to collect basic information on native perennial grasslands in California, the influence of fire on these grasslands, and management tools for restoring and maintaining them. The objective of this study was to review the scientific literature on California native grasslands and summarize the current state of knowledge pertaining to the possible effects -- both beneficial and detrimental -- of prescribed fire on the ecology of Site 300. The results of this review are intended to inform future management practices that may be carried out at Site 300 to maintain the plant and wildlife communities and to ensure that the ecological conditions benefit the special-status species that inhabit the Site. This review is also intended to identify a study approach to investigate changes over the next 10 years in the burned areas and in areas where burning will be discontinued.

  1. Suirr 300, 955 L*Enfwu Plaza. S. Iv.. Washingron. D.C. 200242174.

    Office of Legacy Management (LM)

    Suirr 300, 955 L*Enfwu Plaza. S. Iv.. Washingron. D.C. 200242174. 7117-03.87.cdy.43 23 September 1987 M r. Andrew Wallo, III, NE-23 Division of Facility & Site Decommissioning Projects U.S. Department of Energy Germantown, Maryland 20545 Dear M r. Wallo: I ELIMINATION~RECOMMENDATION -- COLLEGES AND "NIY$RfITIES / t kphonc (202) d.t%xO The attached elimination recommendation was prepared lin accordance with your suggestion during our meeting on 22 September! The recommenda includes 26

  2. Use of Polyphosphate to Decrease Uranium Leaching in Hanford 300 Area Smear Zone Sediments

    SciTech Connect (OSTI)

    Szecsody, James E.; Zhong, Lirong; Oostrom, Martinus; Vermeul, Vincent R.; Fruchter, Jonathan S.; Williams, Mark D.

    2012-09-30

    The primary objective of this study is to summarize the laboratory investigations performed to evaluate short- and long-term effects of phosphate treatment on uranium leaching from 300 area smear zone sediments. Column studies were used to compare uranium leaching in phosphate-treated to untreated sediments over a year with multiple stop flow events to evaluate longevity of the uranium leaching rate and mass. A secondary objective was to compare polyphosphate injection, polyphosphate/xanthan injection, and polyphosphate infiltration technologies that deliver phosphate to sediment.

  3. Notice of Intent to Revise DOE O 200.1A, Information Technology Management--Withdrawn

    Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

    2011-12-15

    Withdrawn 3-24-14. Although DOE O 200.1A was revised in December 2008, there have been significant changes in IT governance processes and Departmental use of new technologies such as Web 2.0 technologies since that time.

  4. Corrosion of high temperature alloys in solar salt at 400, 500, and 680%C2%B0C.

    SciTech Connect (OSTI)

    Kruizenga, Alan Michael; Gill, David Dennis; LaFord, Marianne Elizabeth

    2013-09-01

    Corrosion tests at 400, 500, and 680%C2%B0C were performed using four high temperature alloys; 347SS, 321SS In625, and HA230. Molten salt chemistry was monitored over time through analysis of nitrite, carbonate, and dissolved metals. Metallography was performed on alloys at 500 and 680%C2%B0C, due to the relatively thin oxide scale observed at 400%C2%B0C. At 500%C2%B0C, corrosion of iron based alloys took the form of chromium depletion and iron oxides, while nickel based alloys also had chromium depletion and formation of NiO. Chromium was detected in relatively low concentrations at this temperature. At 680%C2%B0C, significant surface corrosion occurred with metal losses greater than 450microns/year after 1025hours of exposure. Iron based alloys formed complex iron, sodium, and chromium oxides. Some data suggests grain boundary chromium depletion of 321SS. Nickel alloys formed NiO and metallic nickel corrosion morphologies, with HA230 displaying significant internal oxidation in the form of chromia. Nickel alloys both exhibited worse corrosion than iron based alloys likely due to preferential dissolution of chromium, molybdenum, and tungsten.

  5. Irradiation creep of various ferritic alloys irradiated at {approximately}400{degrees}C in the PFR and FFTF reactors

    SciTech Connect (OSTI)

    Toloczko, M.B.; Garner, F.A.; Eiholzer, C.R.

    1997-04-01

    Three ferritic alloys were irradiated in two fast reactors to doses of 50 dpa or more at temperatures near 400{degrees}C. One martensitic alloy, HT9, was irradiated in both the FFTF and PFR reactors. PFR is the Prototype Fast Reactor in Dourneay, Scotland, and FFTF is the Fast Flux Test Facility in Richland, WA. D57 is a developmental alloy that was irradiated in PFR only, and MA957 is a Y{sub 2}O{sub 3} dispersion-hardened ferritic alloy that was irradiated only in FFTF. These alloys exhibited little or no void swelling at {approximately}400{degrees}C. Depending on the alloy starting condition, these steels develop a variety of non-creep strains early in the irradiation that are associated with phase changes. Each of these alloys creeps at a rate that is significantly lower than that of austenitic steels irradiated in the same experiments. The creep compliance for ferritic alloys in general appears to be {approximately}0.5 x 10{sup {minus}6} MPa{sup {minus}1} dpa{sup {minus}1}, independent of both composition and starting state. The addition of Y{sub 2}O{sub 3} as a dispersoid does not appear to change the creep behavior.

  6. Facile synthesis, spectral properties and formation mechanism of sulfur nanorods in PEG-200

    SciTech Connect (OSTI)

    Xie, Xin-yuan; Li, Li-yun; Zheng, Pu-sheng; Zheng, Wen-jie; Bai, Yan; Cheng, Tian-feng; Liu, Jie

    2012-11-15

    Graphical abstract: Homogeneous rod-like structure of sulfur with a typical diameter of about 80 nm and an average aspect ratio of about 68 was obtained. The sulfur nanoparticles could self-assemble from spherical particles to nanorods in PEG-200. During the self-assembling process, the absorption band showed a red shift which was due to the production of nanorods. Highlights: ? A novel, facile and greener method to synthesize sulfur nanorods by the solubilizing and templating effect of PEG-200 was reported. ? S{sup 0} nanoparticles could self assemble in PEG-200 and finally form monodisperse and homogeneous rod-like structure with an average diameter of about 80 nm, the length ca. 600 nm. ? The absorption band showed a red shift and the RRS intensity enhanced continuously during the self-assembling process. ? PEG-200 induced the oriented attachment of sulfur nanoparticles by the terminal hydroxyl groups. -- Abstract: The synthesis of nano-sulfur sol by dissolving sublimed sulfur in a green solvent-PEG-200 was studied. Homogeneous rod-like structure of sulfur with a typical diameter of about 80 nm and an average aspect ratio of 68 was obtained. The structure, morphology, size, and stability of the products were investigated by transmission electron microscopy (TEM), high resolution transmission electron microscopy (HRTEM), X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR) and dynamic light scattering (DLS) measurements. The spectral properties of the products were investigated by ultraviolet-visible (UVvis) absorption and resonance Rayleigh scattering spectroscopy (RRS). The results showed that the spherical sulfur nanoparticles could self-assemble into nanorods in PEG-200. During the self-assembling process, the absorption band showed a red shift and the RRS intensity enhanced continuously. There was physical cross-linking between PEG and sulfur nanoparticles. PEG-200 induced the oriented attachment of sulfur nanoparticles by the terminal

  7. Efficient methylammonium lead iodide perovskite solar cells with active layers from 300 to 900 nm

    SciTech Connect (OSTI)

    Momblona, C.; Malinkiewicz, O.; Soriano, A.; Gil-Escrig, L.; Bandiello, E.; Scheepers, M.; Bolink, H. J.; Edri, E.

    2014-08-01

    Efficient methylammonium lead iodide perovskite-based solar cells have been prepared in which the perovskite layer is sandwiched in between two organic charge transporting layers that block holes and electrons, respectively. This configuration leads to stable and reproducible devices that do not suffer from strong hysteresis effects and when optimized lead to efficiencies close to 15%. The perovskite layer is formed by using a dual-source thermal evaporation method, whereas the organic layers are processed from solution. The dual-source thermal evaporation method leads to smooth films and allows for high precision thickness variations. Devices were prepared with perovskite layer thicknesses ranging from 160 to 900 nm. The short-circuit current observed for these devices increased with increasing perovskite layer thickness. The main parameter that decreases with increasing perovskite layer thickness is the fill factor and as a result optimum device performance is obtained for perovskite layer thickness around 300 nm. However, here we demonstrate that with a slightly oxidized electron blocking layer the fill factor for the solar cells with a perovskite layer thickness of 900 nm increases to the same values as for the devices with thin perovskite layers. As a result the power conversion efficiencies for the cells with 300 and 900 nm are very similar, 12.7% and 12%, respectively.

  8. Adsorption of dysprosium on the graphite (0001) surface: Nucleation and growth at 300 K

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Kwolek, Emma J.; Lei, Huaping; Lii-Rosales, Ann; Wallingford, Mark; Zhou, Yinghui; Wang, Cai -Zhuang; Tringides, Michael C.; Evans, James W.; Thiel, Patricia A.

    2016-06-13

    We have studied nucleation and growth of Dy islands on the basal plane of graphite at 300 K using scanning tunneling microscopy, density functional theory (DFT) in a form that includes van der Waals interactions, and analytic theory. The interaction of atomic Dy with graphite is strong, while the diffusion barrier is small. Experiment shows that at 300 K, the density of nucleated islands is close to the value predicted for homogeneous nucleation, using critical nucleus size of 1 and the DFT-derived diffusion barrier. Homogeneous nucleation is also supported by the monomodal shape of the island size distributions. Comparison withmore » the published island density of Dy on graphene shows that the value is about two orders of magnitude smaller on graphite, which can be attributed to more effective charge screening in graphite. The base of each island is 3 atomic layers high and atomically ordered, forming a coincidence lattice with the graphite. Islands resist coalescence, probably due to multiple rotational orientations associated with the coincidence lattice. Upper levels grow as discernible single-atom layers. Analysis of the level populations reveals significant downward interlayer transport, which facilitates growth of the base. As a result, this island shape is metastable, since more compact three-dimensional islands form at elevated growth temperature.« less

  9. MICROSCALE METABOLIC, REDOX AND ABIOTIC REACTIONS IN HANFORD 300 AREA SUBSURFACE SEDIMENTS

    SciTech Connect (OSTI)

    Beyenal, Haluk; McLEan, Jeff; Majors, Paul; Fredrickson, Jim

    2013-11-14

    The Hanford 300 Area is a unique site due to periodic hydrologic influence of river water resulting in changes in groundwater elevation and flow direction. This area is also highly subject to uranium remobilization, the source of which is currently believed to be the region at the base of the vadose zone that is subject to period saturation due to the changes in the water levels in the Columbia River. We found that microbial processes and redox and abiotic reactions which operate at the microscale were critical to understanding factors controlling the macroscopic fate and transport of contaminants in the subsurface. The combined laboratory and field research showed how microscale conditions control uranium mobility and how biotic, abiotic and redox reactions relate to each other. Our findings extended the current knowledge to examine U(VI) reduction and immobilization using natural 300 Area communities as well as selected model organisms on redox-sensitive and redox-insensitive minerals. Using innovative techniques developed specifically to probe biogeochemical processes at the microscale, our research expanded our current understanding of the roles played by mineral surfaces, bacterial competition, and local biotic, abiotic and redox reaction rates on the reduction and immobilization of uranium.

  10. Feasibility study report for the 200-BP-1 operable unit. Revision 1

    SciTech Connect (OSTI)

    Not Available

    1994-01-01

    This feasibility study (FS) examines a range of alternatives and provides recommendations for selecting a preferred altemative for remediating contamination at the 200-BP-1 operable unit. The 200-BP-1 operable unit is located in the center of the Hanford Site along the northern boundary of the 200 East Area. The 241-BY Tank Farm is located immediately to the south of the operable unit. 200-BP-1 is a source operable unit with contaminated soils associated primarily with nine inactive cribs (known as the 216-B cribs). These cribs were used for disposal of low-level radioactive liquid waste from U Plant uranium recovery operations, and waste storage tank condensate from the adjacent 241-BY Tank Farm. The cribs used for disposal of U Plant waste were in operation from 1955--1965, and the cribs used for disposal of tank condensate were in operation from 1965-1975. In addition to the cribs, four unplanned releases of radioactive materials have occurred within the operable unit. Contaminated surface soils associated with the unplanned releases have been consolidated over the cribs and covered with clean soil to reduce contaminant migration and exposure. Discharge of wastes to the cribs has resulted in soil and groundwater contamination. The groundwater is being addressed as part of the 200 East Aggregate Area groundwater operable unit. Contaminated soils at the site can be categorized by the types of contaminants, their distribution in the soil column, and the risk posed by the various potential exposure pathways. Below the clean soil cover, the near surface soils contain low-:levels of contamination with cesium-137, radium-226, strontium-90, thorium-228 and uranium. The lifetime incremental cancer risk associated with these soils if they were exposed at the surface is 9 {times} 10{sup 5}.

  11. Final Hazard Categorization for the Remediation of Six 300-FF-2 Operable Unit Solid Waste Burial Grounds

    SciTech Connect (OSTI)

    J. D. Ludowise; K. L. Vialetti

    2008-05-12

    This report provides the final hazard categorization for the remediation of six 300-FF-2 Operable Unit Burial Grounds, the 618-1, 618-2, 618-3, 618-7, 618-8, and 618-13 sites.

  12. Pilot-scale treatability test plan for the 200-BP-5 operable unit

    SciTech Connect (OSTI)

    Not Available

    1994-08-01

    This document presents the treatability test plan for pilot-scale pump and treat testing at the 200-BP-5 Operable Unit. This treatability test plan has been prepared in response to an agreement between the U.S. Department of Energy (DOE), the U.S. Environmental Protection Agency (EPA), and the State of Washington Department of Ecology (Ecology), as documented in Hanford Federal Facility Agreement and Consent Order (Tri-Party Agreement, Ecology et al. 1989a) Change Control Form M-13-93-03 (Ecology et al. 1994) and a recent 200 NPL Agreement Change Control Form (Appendix A). The agreement also requires that, following completion of the activities described in this test plan, a 200-BP-5 Operable Unit Interim Remedial Measure (IRM) Proposed Plan be developed for use in preparing an Interim Action Record of Decision (ROD). The IRM Proposed Plan will be supported by the results of this treatability test plan, as well as by other 200-BP-5 Operable Unit activities (e.g., development of a qualitative risk assessment). Once issued, the Interim Action ROD will specify the interim action(s) for groundwater contamination at the 200-BP-5 Operable Unit. The treatability test approach is to conduct a pilot-scale pump and treat test for each of the two contaminant plumes associated with the 200-BP-5 Operable Unit. Primary contaminants of concern are {sup 99}Tc and {sup 60}Co for underwater affected by past discharges to the 216-BY Cribs, and {sup 90}Sr, {sup 239/240}Pu, and Cs for groundwater affected by past discharges to the 216-B-5 Reverse Well. The purpose of the pilot-scale treatability testing presented in this testplan is to provide the data basis for preparing an IRM Proposed Plan. To achieve this objective, treatability testing must: Assess the performance of groundwater pumping with respect to the ability to extract a significant amount of the primary contaminant mass present in the two contaminant plumes.

  13. 70003-MAPPER FAB CARRIAGE ASSY

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    RSF RSF RSF 70003 2107 - 2107 - - - INITIAL ISSUE - - WEIGHT: 1563 LBS 146.00 CENT REF 3.00 4.00 150.00 CENT REF 6.00 SQ .50 WALL 2.00 .25 WALL 4.00 3.50 0 5.00 57.00 58.00...

  14. Remedial investigation of the High-Explosives (HE) Process Area, Lawrence Livermore National Laboratory Site 300

    SciTech Connect (OSTI)

    Crow, N.B.; Lamarre, A.L.

    1990-08-01

    This report presents the results of a Remedial Investigation (RI) to define the extent of high explosives (HE) compounds and volatile organic compounds (VOCs) found in the soil, rocks, and ground water of the HE Process Area of Lawrence Livermore National Laboratory's (LLNL) Site 300 Facility. The report evaluates potential public health environmental risks associated with these compounds. Hydrogeologic information available before February 15, 1990, is included; however, chemical analyses and water-level data are reported through March 1990. This report is intended to assist the California Regional Water Quality Control Board (RWQCB)--Central Valley Region and the US Environmental Protection Agency (EPA) in evaluating the extent of environmental contamination of the LLNL HE Process Area and ultimately in designing remedial actions. 90 refs., 20 figs., 7 tabs.

  15. A Novel Fuel/Reactor Cycle to Implement the 300 Years Nuclear Waste Policy Approach - 12377

    SciTech Connect (OSTI)

    Carelli, M.D.; Franceschini, F.; Lahoda, E.J.; Petrovic, B.

    2012-07-01

    A thorium-based fuel cycle system can effectively burn the currently accumulated commercial used nuclear fuel and move to a sustainable equilibrium where the actinide levels in the high level waste are low enough to yield a radiotoxicity after 300 years lower than that of the equivalent uranium ore. The second step of the Westinghouse approach to solving the waste 'problem' has been completed. The thorium fuel cycle has indeed the potential of burning the legacy TRU and achieve the waste objective proposed. Initial evaluations have been started for the third step, development and selection of appropriate reactors. Indications are that the probability of show-stoppers is rather remote. It is, therefore, believed that development of the thorium cycle and associated technologies will provide a permanent solution to the waste management. Westinghouse is open to the widest collaboration to make this a reality. (authors)

  16. Hazardous waste site assessment: Inactive landfill, Site 300, Lawrence Livermore National Laboratory

    SciTech Connect (OSTI)

    Not Available

    1985-01-01

    This report presents the results of an investigation of an inactive landfill (Pit 6) at Lawrence Livermore National Laboratory's (LLNL) Site 300. The primary objectives were to: collect and review background information pertaining to past waste disposal practices and previous environmental characterization studies; conduct a geophysical survey of the landfill area to locate the buried wastes; conduct a hydrogeologic investigation to provide additional data on the rate and direction of groundwater flow, the extent of any groundwater contamination, and to investigate the connection, if any, of the shallow groundwater beneath the landfill with the local drinking water supply; conduct a risk assessment to identify the degree of threat posed by the landfill to the public health and environment; compile a preliminary list of feasible long-term remedial action alternatives for the landfill; and develop a list of recommendations for any interim measures necessary at the landfill should the long-term remedial action plan be needed.

  17. Title I conceptual design for Pit 6 landfill closure at Lawrence Livermore National Laboratory Site 300

    SciTech Connect (OSTI)

    MacDonnell, B.A.; Obenauf, K.S.

    1996-08-01

    The objective of this design project is to evaluate and prepare design and construction documents for a closure cover cap for the Pit 6 Landfill located at Lawrence Livermore National Laboratory Site 300. This submittal constitutes the Title I Design (Conceptual Design) for the closure cover of the Pit 6 Landfill. A Title I Design is generally 30 percent of the design effort. Title H Design takes the design to 100 percent complete. Comments and edits to this Title I Design will be addressed in the Title II design submittal. Contents of this report are as follows: project background; design issues and engineering approach; design drawings; calculation packages; construction specifications outline; and construction quality assurance plan outline.

  18. REVIEW REPORT: BUILDING C-400 THERMAL TREATMENT 90 PERCENT REMEDIAL DESIGN REPORT AND SITE INVESTIGATION, PGDP, PADUCAH, KENTUCKY

    SciTech Connect (OSTI)

    Looney, B; Jed Costanza, J; Eva Davis, E; Joe Rossabi, J; Lloyd Stewart, L; Hans Stroo, H

    2007-08-15

    On 9 April 2007, the U.S. Department of Energy (DOE) Headquarters, Office of Soil and Groundwater Remediation (EM-22) initiated an Independent Technical Review (ITR) of the 90% Remedial Design Report (RDR) and Site Investigation (RDSI) for thermal treatment of trichloroethylene (TCE) in the soil and groundwater in the vicinity of Building C-400 at the Paducah Gaseous Diffusion Plant (PGDP). The general ITR goals were to assess the technical adequacy of the 90% RDSI and provide recommendations sufficient for DOE to determine if modifications are warranted pertaining to the design, schedule, or cost of implementing the proposed design. The ultimate goal of the effort was to assist the DOE Paducah/Portsmouth Project Office (PPPO) and their contractor team in ''removing'' the TCE source zone located near the C-400 Building. This report provides the ITR findings and recommendations and supporting evaluations as needed to facilitate use of the recommendations. The ITR team supports the remedial action objective (RAO) at C-400 to reduce the TCE source area via subsurface Electrical Resistance Heating (ERH). Further, the ITR team commends PPPO, their contractor team, regulators, and stakeholders for the significant efforts taken in preparing the 90% RDR. To maximize TCE removal at the target source area, several themes emerge from the review which the ITR team believes should be considered and addressed before implementing the thermal treatment. These themes include the need for: (1) Accurate and site-specific models as the basis to verify the ERH design for full-scale implementation for this challenging hydrogeologic setting; (2) Flexible project implementation and operation to allow the project team to respond to observations and data collected during construction and operation; (3) Defensible performance metrics and monitoring, appropriate for ERH, to ensure sufficient and efficient clean-up; and (4) Comprehensive (creative and diverse) contingencies to address the

  19. Irradiation Creep and Swelling from 400 C to 600 C of the Oxide Dispersion Strengthened Ferritic Alloy MA957

    SciTech Connect (OSTI)

    Toloczko, Mychailo B.; Gelles, David S.; Garner, Francis A.; Kurtz, Richard J.; Abe, Katsunori

    2004-04-24

    Recently, there has been a growing interest in the use of oxide dispersion strengthened (ODS) ferritic steels for fusion reactor applications. As part of an extensive study performed at PNNL on the ODS steel MA957 [1], irradiation creep tests were performed on pressurized tubes made from MA957 by two different methods. The tubes were made either by gun drilling alone or by a combination of rod drawing and gun drilling. The different fabrication methods were explored because ODS steels have been difficult to form. The pressurized tubes were irradiated in the Fast Flux Test Facility (FFTF) to doses ranging from 40 dpa to 110 dpa at temperatures ranging from 400 C to 600 C. The effective stresses resulting from the pressurization of the tubes ranged from 0 MPa to 175 MPa.

  20. Effects of solar ultraviolet photons on mammalian cell DNA. [UVA (320-400 nm):a2

    SciTech Connect (OSTI)

    Peak, M.J.; Peak, J.G.

    1991-01-01

    This document presents information on the possible mechanisms of carcinogenesis caused by UVA (ultraviolet radiation in the 320--400 nm region). Most studies showing the carcinogenic effects of ultraviolet light have concentrated on UVB (280--320 nm). UVA had been considered harmless even though it penetrates biological tissues better than UVB. Recently, it has become apparent that UVA is also capable of causing damage to cellular DNA. This was unexpected because the DNA UV absorption spectrum indicates a negligible probability that photons of wavelengths longer than 320 nm will be directly absorbed. The most common defects induced in DNA by UVB are pyrimidine photoproducts, such as thymidine dimers. UVA photons produce defects resembling those caused by ionizing radiations: single- and double-strand breaks, and DNA-protein crosslinks. This paper also discusses the role of DNA repair mechanisms in UVA-induced defects and the molecular mechanisms of UVA damage induction. 38 refs. (MHB)

  1. Observation of parametric X-rays produced by 400 GeV/c protons in bent crystals

    SciTech Connect (OSTI)

    Scandale , W.; Robert-Demolaize, G.; Arduini, G.; Assmann, R.; Cerutti, F. et al

    2011-05-30

    Spectral maxima of parametric X-ray radiation (PXR) produced by 400 GeV/c protons in bent silicon crystals aligned with the beam have been observed in an experiment at the H8 external beam of the CERN SPS. The total yield of PXR photons was about 10{sup -6} per proton. Agreement between calculations and the experimental data shows that the PXR kinematic theory is valid for bent crystals with sufficiently small curvature as used in the experiment. The intensity of PXR emitted from halo protons in a bent crystal used as a primary collimator in a circular accelerator may be considered as a possible tool to control its crystal structure, which is slowly damaged because of irradiation. The intensity distribution of PXR peaks depends on the crystal thickness intersected by the beam, which changes for different orientations of a crystal collimator. This dependence may be used to control crystal collimator alignment by analyzing PXR spectra produced by halo protons.

  2. Observation of Parametric X-Rays Produced by 400-GeV/C Protons in Bent Crystals

    SciTech Connect (OSTI)

    Scandale, W.; Arduini, G.; Assmann, R.; Cerutti, F.; Gilardoni, S.; Christiansen, J.; Laface, E.; Losito, R.; Masi, A.; Metral, E.; Mirarchi, D.; Montesano, S.; Previtali, V.; Redaelli, S.; Valentino, G.; Schoofs, P.; Smirnov, G.; Tlustos, L.; Bagli, E.; Baricordi, S.; Dalpiaz, P.; /Ferrara U. /INFN, Ferrara /Ferrara U. /INFN, Ferrara /Ferrara U. /INFN, Ferrara /Ferrara U. /INFN, Ferrara /Frascati /Frascati /Frascati /INFN, Legnaro /INFN, Legnaro /INFN, Legnaro /INFN, Legnaro /INFN, Legnaro /INFN, Legnaro /INFN, Rome /INFN, Rome /INFN, Rome /INFN, Rome /INFN, Naples /Serpukhov, IHEP /Serpukhov, IHEP /Serpukhov, IHEP /Serpukhov, IHEP /Serpukhov, IHEP /Dubna, JINR /Dubna, JINR /St. Petersburg, INP /St. Petersburg, INP /St. Petersburg, INP /St. Petersburg, INP /Imperial Coll., London /Imperial Coll., London /Imperial Coll., London /Imperial Coll., London /Imperial Coll., London /Imperial Coll., London /Imperial Coll., London /Imperial Coll., London /Brookhaven /SLAC /SLAC /SLAC /IPTP, Dubna /Tomsk Polytechnic U. /Tomsk Polytechnic U.

    2012-05-07

    Spectral maxima of parametric X-ray radiation (PXR) produced by 400 GeV/c protons in bent silicon crystals aligned with the beam have been observed in an experiment at the H8 external beam of the CERN SPS. The total yield of PXR photons was about 10{sup -6} per proton. Agreement between calculations and the experimental data shows that the PXR kinematic theory is valid for bent crystals with sufficiently small curvature as used in the experiment. The intensity of PXR emitted from halo protons in a bent crystal used as a primary collimator in a circular accelerator may be considered as a possible tool to control its crystal structure, which is slowly damaged because of irradiation. The intensity distribution of PXR peaks depends on the crystal thickness intersected by the beam, which changes for different orientations of a crystal collimator. This dependence may be used to control crystal collimator alignment by analyzing PXR spectra produced by halo protons.

  3. Deuterated palladium at temperatures from 4. 3 to 400 K and pressures to 105 kbar: Search for cold fusion

    SciTech Connect (OSTI)

    Silvera, I.F.; Moshary, F. )

    1990-11-15

    We have studied a sample of deuterated palladium at pressures up to 105 kbar and temperatures from 4.3 to 400 K in an effort to detect cold fusion. A (D)/(Pd) concentration of 1.34{plus minus}0.1 was achieved. No evidence of cold fusion was found with a limit of 2.5{times}10{sup {minus}18} fusions (DD pair){sup {minus}1} s{sup {minus}1} from neutron detection and 1.5{times}10{sup {minus}8} fusions (DD pair){sup {minus}1} s{sup {minus}1} from detection of possible heating; a {gamma}-ray detector showed no evidence of {gamma} rays differing from background.

  4. Environmental assessment for the Explosive Waste Treatment Facility at Site 300, Lawrence Livermore National Laboratory

    SciTech Connect (OSTI)

    1995-11-01

    Lawrence Livermore National Laboratory proposes to build, permit, and operate the Explosive Waste Treatment Facility (EWTF) to treat explosive waste at LLNL`s Experimental Test Site, Site 300. It is also proposed to close the EWTF at the end of its useful life in accordance with the regulations. The facility would replace the existing Building 829 Open Burn Facility (B829) and would treat explosive waste generated at the LLNL Livermore Site and at Site 300 either by open burning or open detonation, depending on the type of waste. The alternatives addressed in the 1992 sitewide EIS/EIR are reexamined in this EA. These alternatives included: (1) the no-action alternative which would continue open burning operations at B829; (2) continuation of only open burning at a new facility (no open detonation); (3) termination of open burning operations with shipment of explosive waste offsite; and (4) the application of alternative treatment technologies. This EA examines the impact of construction, operation, and closure of the EWTF. Construction of the EWTF would result in the clearing of a small amount of previously disturbed ground. No adverse impact is expected to any state or federal special status plant or animal species (special status species are classified as threatened, endangered, or candidate species by either state or federal legislation). Operation of the EWTF is expected to result in a reduced threat to involved workers and the public because the proposed facility would relocate existing open burning operations to a more remote area and would incorporate design features to reduce the amount of potentially harmful emissions. No adverse impacts were identified for activities necessary to close the EWTF at the end of its useful life.

  5. Application of RAD-BCG calculator to Hanford's 300 area shoreline characterization dataset

    SciTech Connect (OSTI)

    Antonio, Ernest J.; Poston, Ted M.; Tiller, Brett L.; Patton, Gene W.

    2003-07-01

    Abstract. In 2001, a multi-agency study was conducted to characterize potential environmental effects from radiological and chemical contaminants on the near-shore environment of the Columbia River at the 300 Area of the U.S. Department of Energy’s Hanford Site. Historically, the 300 Area was the location of nuclear fuel fabrication and was the main location for research and development activities from the 1940s until the late 1980s. During past waste handling practices uranium, copper, and other heavy metals were routed to liquid waste streams and ponds near the Columbia River shoreline. The Washington State Department of Health and the Pacific Northwest National Laboratory’s Surface Environmental Surveillance Project sampled various environmental components including river water, riverbank spring water, sediment, fishes, crustaceans, bivalve mollusks, aquatic insects, riparian vegetation, small mammals, and terrestrial invertebrates for analyses of radiological and chemical constituents. The radiological analysis results for water and sediment were used as initial input into the RAD-BCG Calculator. The RAD-BCG Calculator, a computer program that uses an Excel® spreadsheet and Visual Basic® software, showed that maximum radionuclide concentrations measured in water and sediment were lower than the initial screening criteria for concentrations to produce dose rates at existing or proposed limits. Radionuclide concentrations measured in biota samples were used to calculate site-specific bioaccumulation coefficients (Biv) to test the utility of the RAD-BCG-Calculator’s site-specific screening phase. To further evaluate site-specific effects, the default Relative Biological Effect (RBE) for internal alpha particle emissions was reduced by half and the program’s kinetic/allometric calculation approach was initiated. The subsequent calculations showed the initial RAD-BCG Calculator results to be conservative, which is appropriate for screening purposes.

  6. NuSTAR DISCOVERY OF A CYCLOTRON LINE IN KS 1947+300

    SciTech Connect (OSTI)

    Fürst, Felix; Bellm, Eric; Harrison, Fiona; Walton, Dominic J.; Pottschmidt, Katja; Wilms, Jörn; Kennea, Jamie; Bachetti, Matteo; Boggs, Steven E.; Craig, William W.; Tomsick, John A.; Chakrabarty, Deepto; Christensen, Finn E.; Hailey, Charles J.; Stern, Daniel; Zhang, William

    2014-04-01

    We present a spectral analysis of three simultaneous Nuclear Spectroscopy Telescope Array and Swift/XRT observations of the transient Be-neutron star binary KS 1947+300 taken during its outburst in 2013/2014. These broadband observations were supported by Swift/XRT monitoring snapshots every three days, which we use to study the evolution of the spectrum over the outburst. We find strong changes of the power-law photon index, which shows a weak trend of softening with increasing X-ray flux. The neutron star shows very strong pulsations with a period of P ≈ 18.8 s. The 0.8-79 keV broadband spectrum can be described by a power law with an exponential cutoff and a blackbody component at low energies. During the second observation we detect a cyclotron resonant scattering feature at 12.5 keV, which is absent in the phase-averaged spectra of observations 1 and 3. Pulse phase-resolved spectroscopy reveals that the strength of the feature changes strongly with pulse phase and is most prominent during the broad minimum of the pulse profile. At the same phases the line also becomes visible in the first and third observation at the same energy. This discovery implies that KS 1947+300 has a magnetic field strength of B ≈ 1.1 × 10{sup 12}(1 + z) G, which is at the lower end of known cyclotron line sources.

  7. Revised Methodology for Determining Cesium-137 Content of HN-200 Grout Containers

    SciTech Connect (OSTI)

    SHELOR, J.L.

    1999-08-31

    The purpose of this technical paper is to examine the accuracy of the existing method of determining the Cs-137 content of HN-200 grout containers and compare that accuracy to the accuracy attainable by other methods of measurement. The methods of measurement to be compared include: Contact measurements on a grouted container (existing method); Measurements at 5 feet from the surface of a grouted container; Measurements at 10 feet from a grouted container; Measurements on contact with the surface of an ungrouted container; Measurements at 5 feet from the surface of an ungrouted container; and Measurements at 10 feet from the surface of an ungrouted container. Once the most accurate and useable method is determined, the precepts for an operating procedure will be provided for determining the Cs-137 content of newly generated and future HN-200 grout containers as well as the grouted legacy containers currently stored in B Cell.

  8. A 30 MW, 200 MHz Inductive Output Tube for RF Accelerators

    SciTech Connect (OSTI)

    R. Lawrence Ives; Michael Read

    2008-06-19

    This program investigated development of a multiple beam inductive output tube (IOT) to produce 30 MW pulses at 200 MHz. The program was successful in demonstrating feasibility of developing the source to achieve the desired power in microsecond pulses with 70% efficiency. The predicted gain of the device is 24 dB. Consequently, a 200 kW driver would be required for the RF input. Estimated cost of this driver is approximately $1.25 M. Given the estimated development cost of the IOT of approximately $750K and the requirements for a test set that would significantly increase the cost, it was determined that development could not be achieved within the funding constraints of a Phase II program.

  9. NREL: Technology Deployment - Combined Energy Savings of $200,000 Per Year

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Achieved in Greensburg, Kansas Combined Energy Savings of $200,000 Per Year Achieved in Greensburg, Kansas News Greensburg, Kansas, Five Years Later-An International Inspiration for Green Disaster Recovery Publications Rebuilding It Better: Greensburg, Kansas Rebuilding Greensburg, Kansas, as a Model Green Community: A Case Study From Tragedy to Triumph: Rebuilding Greensburg, Kansas, To Be a 100% Renewable Energy City Integrated Deployment: Disaster Recovery Sponsors U.S. Department of

  10. 200 Area Treated Effluent Disposal Facility (TEDF) Effluent Sampling and Analysis Plan

    SciTech Connect (OSTI)

    BROWN, M.J.

    2000-05-18

    This Sampling and Analysis Plan (SAP) has been developed to comply with effluent monitoring requirements at the 200 Area Treated Effluent Disposal Facility (TEDF), as stated in Washington State Waste Discharge Permit No. ST 4502 (Ecology 2000). This permit, issued by the Washington State Department of Ecology (Ecology) under the authority of Chapter 90.48 Revised Code of Washington (RCW) and Washington Administrative Code (WAC) Chapter 173-216, is an April 2000 renewal of the original permit issued on April 1995.

  11. Analysis and decision document in support of acquisition of steam supply for the Hanford 200 Area

    SciTech Connect (OSTI)

    Brown, D.R.; Daellenbach, K.K.; Hendrickson, P.L.; Kavanaugh, D.C.; Reilly, R.W.; Shankle, D.L.; Smith, S.A.; Weakley, S.A.; Williams, T.A. ); Grant, T.F. )

    1992-02-01

    The US Department of Energy (DOE) is now evaluating its facility requirements in support of its cleanup mission at Hanford. One of the early findings is that the 200-Area steam plants, constructed in 1943, will not meet future space heating and process needs. Because the 200 Area will serve as the primary area for waste treatment and long-term storage, a reliable steam supply is a critical element of Hanford operations. This Analysis and Decision Document (ADD) is a preliminary review of the steam supply options available to the DOE. The ADD contains a comprehensive evaluation of the two major acquisition options: line-term versus privatization. It addresses the life-cycle costs associated with each alternative, as well as factors such as contracting requirements and the impact of market, safety, security, and regulatory issues. Specifically, this ADD documents current and future steam requirements for the 200 Area, describes alternatives available to DOE for meeting these requirements, and compares the alternatives across a number of decision criteria, including life-cycle cost. DOE has currently limited the ADD evaluation alternatives to replacing central steam plants rather than expanding the study to include alternative heat sources, such as a distributed network of boilers or heat pumps. Thirteen project alternatives were analyzed in the ADD. One of the alternatives was the rehabilitation of the existing 200-East coal-fired facility. The other twelve alternatives are combinations of (1) coal- or gas-fueled plants, (2) steam-only or cogeneration facilities, (3) primary or secondary cogeneration of electricity, and (4) public or private ownership.

  12. Operational Safety Requirements and Operating Specification Documentation compliance instrumentation matrices: 200 East Area Tank Farms

    SciTech Connect (OSTI)

    Story, D.R.

    1995-03-01

    This document contains information about matrices complied of instrumentation used to comply with the existing Operational Safety Requirements from Safety Analysis Reports and Operating, Specification Documentation requirements for 200 East Area Tank Farms. These matrices contain the primary instrumentation needed to comply with each OSR and/or OSD requirement as well as any backup instrumentation that may be used should the primary device be out of service. The referenced matrices are provided as attachments to this document.

  13. Systematic Study of Trace Radioactive Impurities in Candidate Construction Materials for EXO-200

    SciTech Connect (OSTI)

    Leonard, D.S.; Grinberg, P.; Weber, P.; Baussan, E.; Djurcic, Z.; Keefer, G.; Piepke, A.; Pocar, A.; Vuilleumier, J.-L.; Vuilleumier, J.-M.; Akimov, D.; Bellerive, A.; Bowcock, M.; Breidenbach, M.; Burenkov, A.; Conley, R.; Craddock, W.; Danilov, M.; DeVoe, R.; Dixit, M.; Dolgolenko, A.; /Alabama U. /NRC-INMS /Neuchatel U. /Stanford U., Phys. Dept. /SLAC /Colorado State U. /Laurentian U. /Maryland U. /UC, Irvine

    2007-10-24

    The Enriched Xenon Observatory (EXO) will search for double beta decays of 136Xe. We report the results of a systematic study of trace concentrations of radioactive impurities in a wide range of raw materials and finished parts considered for use in the construction of EXO-200, the first stage of the EXO experimental program. Analysis techniques employed, and described here, include direct gamma counting, alpha counting, neutron activation analysis, and high-sensitivity mass spectrometry.

  14. LESSONS LEARNED - STARTUP AND TRANSITION TO OPERATIONS AT THE 200 WEST PUMP AND TREAT FACILITY

    SciTech Connect (OSTI)

    FINK DE; BERGQUIST GG; BURKE SP

    2012-10-03

    This document lists key Lessons Learned from the Startup Team for the 200 West Pump and Treat Facility Project. The Startup Team on this Project was an integrated, multi-discipline team whose scope was Construction Acceptance Testing (CAT), functional Acceptance Testing Procedures (ATP), and procedure development and implementation. Both maintenance and operations procedures were developed. Included in the operations procedures were the process unit operations. In addition, a training and qualification program was also part of the scope.

  15. Statistical Evaluation of Effluent Monitoring Data for the 200 Area Treated Effluent Disposal Facility

    SciTech Connect (OSTI)

    Chou, Charissa J; Johnson, Vernon G

    2000-03-08

    This report updates the original effluent variability study for the 200 Area Treated Effluent Disposal Facility (TEDF) and provides supporting justification for modifying the effluent monitoring portion of the discharge permit. Four years of monitoring data were evaluated and used to statistically justify changes in permit effluent monitoring conditions. As a result, the TEDF effluent composition and variability of the effluent waste stream are now well defined.

  16. Strangelet search in S-W collisions at 200[ital A] GeV/[ital c

    SciTech Connect (OSTI)

    Borer, K.; Dittus, F.; Frei, D.; Hugentobler, E.; Klingenberg, R.; Moser, U.; Pretzl, K.; Schacher, J.; Stoffel, F.; Volken, W. ); Elsener, K.; Lohmann, K.D. ); Baglin, C.; Bussiere, A.; Guillaud, J.P. ); Appelquist, G.; Bohm, C.; Hovander, B.; Sellden, B.; Zhang, Q.P. )

    1994-03-07

    A search for new massive particles with a low charge to mass ratio in S-W collisions at a beam momentum of 200 GeV/[ital c] per nucleon is presented. Upper limits for the production of strangelets with a mass to charge ratio of up to 60 GeV/[ital c][sup 2] at rigidities of [plus minus]150 GV are reported.

  17. V-200: Apache Struts DefaultActionMapper Redirection and OGNL Security

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Bypass Vulnerabilities | Department of Energy 0: Apache Struts DefaultActionMapper Redirection and OGNL Security Bypass Vulnerabilities V-200: Apache Struts DefaultActionMapper Redirection and OGNL Security Bypass Vulnerabilities July 18, 2013 - 6:00am Addthis PROBLEM: Two weaknesses and multiple vulnerabilities have been reported in Apache Struts PLATFORM: Apache Struts 2.x ABSTRACT: The vulnerabilities can be exploited by malicious people to conduct spoofing attacks and bypass certain

  18. Life-cycle cost analysis 200-West Weather Enclosure: Multi-function Waste Tank Facility

    SciTech Connect (OSTI)

    Umphrey, M.R.

    1995-01-16

    The Multi-Function Waste Tank Facility (MWTF)will provide environmentally safe and acceptable storage capacity for handling wastes resulting from the remediation of existing single-shell and double-shell tanks on the Hanford Site. The MWTF will construct two tank farm facilities at two separate locations. A four-tank complex will be constructed in the 200-East Area of the Hanford Site; a two-tank complex will be constructed in the 200-West Area. This report documents the results of a life-cycle cost analysis performed by ICF Kaiser Hanford Company (ICF KH) for the Weather Enclosure proposed to be constructed over the 200-West tanks. Currently, all tank farm operations on the Hanford Site are conducted in an open environment, with weather often affecting tank farm maintenance activities. The Weather Enclosure is being proposed to allow year-round tank farm operation and maintenance activities unconstrained by weather conditions. Elimination of weather-related delays at the MWTF and associated facilities will reduce operational costs. The life-cycle cost analysis contained in this report analyzes potential cost savings based on historical weather information, operational and maintenance costs, construction cost estimates, and other various assumptions.

  19. Description of work for 200-UP-1 characterization of monitoring wells

    SciTech Connect (OSTI)

    Innis, B.E.; Kelty, G.G.

    1994-02-01

    This description of work (DOW) details the field activities associated with the drilling, soil sampling, and construction of groundwater monitoring and dual-use wells in the 200-UP-1 Operable Unit (Tasks 2, 3, and 5 in the 200-UP-1 RI/FS Work Plan DOE/RL 1993a) and will serve as a field guide for those performing the work. It will be used in conjunction with the Remedial Investigation/Feasibility Study Work Plan for the 200-UP-1 Groundwater operable Unit (DOE-RL 1993a, [LFI]) and Site Characterization Manual (WHC 1988a). Groundwater wells are being constructed to characterize the vertical and horizontal extent of the Uranium and {sup 99}{Tc} plumes and to define aquifer properties such as hydraulic communication between aquifers and hydrostratigraphy. Some of these wells may be utilized for extraction purposes during the IRM phase anticipated at this operable unit and are being designed with a dual use in mind. These data will be used to optimize the Interim Remedial Measures (IRM) for the cleanup of these two plumes. The data will also be used with later Limited Field Investigation (LFI) data to perform a Qualitative Risk Assessment (QRA) for the operable unit. The locations for the proposed groundwater wells are presented in Figure 1. The contaminants of concern for the project are presented ih Table 1.

  20. 3He Cross Section

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    3He(pol. p, +): differential 200, 300, 400 X4 10302014 1985EP01 3He(p, 2p), (p, pd): 300, 450 X4 10302014 1977FR05 3He(p, p): differential 415, 600, 800 cm ...

  1. M400.pdf

    National Nuclear Security Administration (NNSA)

  2. Startup of the New 200 West Pump-and-Treat, Hanford Site, Richland, Washington - 13214

    SciTech Connect (OSTI)

    Byrnes, Mark E.; Simmons, Sally; Morse, John

    2013-07-01

    On June 28, 2012, CH2M HILL Plateau Remediation Company (CHPRC) completed the construction and acceptance testing for a new 2,500 gallon-per-minute (gpm) pump-and-treat (P and T) system in the 200 West Area of the Hanford Site in Washington State. This system is designed to remove Tc-99, carbon tetrachloride, trichloroethene (TCE), nitrate, and total and hexavalent chromium from groundwater using ion exchange, anoxic and aerobic bioreactors, and air stripping. The system will eventually remove uranium from groundwater using ion exchange as well. The startup of the P and T system is important because it will ensure that contaminants from the 200 West Area never reach the Columbia River. When fully operational, the 200 West P and T will include approximately 23 extraction wells and 21 injection wells. The extraction wells are 8 inches in diameter, are completed with well screens 100 feet or more in length, and are distributed throughout the central portion of the 5-square-mile carbon tetrachloride plume. The injection wells are also 8 inches in diameter and are installed up-gradient of the plumes to recharge the aquifer and down-gradient of the plumes for flow-path control. Groundwater in the 200 West Area is approximately 250 feet below ground surface, and the aquifer is 200 feet or more in thickness. All of the contaminants (except nitrate) are found within the perimeter of the carbon tetrachloride plume and occur at various depths throughout the aquifer. The 200 West P and T consists of two separate buildings to conduct groundwater treatment. The RAD building contains an ion exchange system to remove Tc-99 from groundwater at a maximum flow rate of 600 gpm. The RAD building only accepts water from those extraction wells showing elevated Tc-99 concentrations. Groundwater initially fills an influent tank, is then pumped through particulate filters (to remove suspended materials), and then passes through two parallel treatment trains containing Purolite{sup R} A530E

  3. 2010 Dry and 2009 - 2010 Wet Season Branchiopod Survey Report, Site 300

    SciTech Connect (OSTI)

    Dexter, W

    2011-03-14

    Lawrence Livermore National Laboratory (LLNL) requested that Condor Country Consulting, Inc. (CCCI) perform wet season surveys and manage the dry season sampling for listed branchiopods in two ponded locations within the Site 300 Experimental Test Site. Site 300 is located in Alameda and San Joaquin Counties, located between the Cities of Livermore and Tracy. The two pool locations have been identified for possible amphibian enhancement activities in support of the Compensation Plan for impacts tied to the Building 850 soil clean-up project. The Building 850 project design resulted in formal consultation with the U.S. Fish and Wildlife Service (USFWS) as an amendment (File 81420-2009-F-0235) to the site-wide Biological Opinion (BO) (File 1-1-02-F-0062) in the spring of 2009 and requires mitigation for the California tiger salamander (AMCA, Ambystoma californiense) and California red-legged frog (CRLF, Rana draytonii) habitat loss. Both pools contain breeding AMCA, but do not produce metamorphs due to limited hydroperiod. The pool to the southeast (Pool BC-FS-2) is the preferred site for amphibian enhancement activities, and the wetland to northwest (Pool OA-FS-1) is the alternate location for enhancement. However, prior to enhancement, LLNL has been directed by USFWS (BO Conservation Measure 17 iii) to 'conduct USFWS protocol-level branchiopod surveys to determine whether listed brachiopod species are present within the compensation area.' CCCI conducted surveys for listed branchiopods in the 2009-2010 wet season to determine the presence of federally-listed branchiopods at the two pools (previous surveys with negative findings were performed by CCCI in 2001-2002 and 2002-2003 onsite). Surveys were conducted to partially satisfy the survey requirements of the USFWS 'Interim Survey Guidelines to Permittees for Recovery Permits under Section 10(a)(1)(A) of the Endangered Species Act for the Listed Vernal Pool Branchiopods' ('Guidelines, USFWS 1996 and BO Conservation

  4. Data Package of Samples Collected for Hydrogeologic and Geochemical Characterization: 300 Area RI/FS Sediment Cores

    SciTech Connect (OSTI)

    Lindberg, Michael J.; Bjornstad, Bruce N.; Lanigan, David C.; Williams, Benjamin D.

    2011-05-01

    This is a data package for sediment samples received from the 300 FF 5 OU. This report was prepared for CHPRC. Between August 16, 2010 and April 25, 2011 sediment samples were received from 300-FF-5 for geochemical studies. The analyses for this project were performed at the 331 building located in the 300 Area of the Hanford Site. The analyses were performed according to Pacific Northwest National Laboratory (PNNL) approved procedures and/or nationally recognized test procedures. The data sets include the sample identification numbers, analytical results, estimated quantification limits (EQL), and quality control data. The preparatory and analytical quality control requirements, calibration requirements, acceptance criteria, and failure actions are defined in the on-line QA plan 'Conducting Analytical Work in Support of Regulatory Programs' (CAW). This QA plan implements the Hanford Analytical Services Quality Assurance Requirements Documents (HASQARD) for PNNL.

  5. Request for modification of 200 Area effluent treatment facility final delisting

    SciTech Connect (OSTI)

    BOWMAN, R.C.

    1998-11-19

    A Delisting Petition submitted to the U.S. Environmental Protection Agency in August 1993 addressed effluent to be generated at the 200 Area Effluent Treatment Facility from treating Hanford Facility waste streams. This Delisting Petition requested that 71.9 million liters per year of treated effluent, bearing the designation 'F001' through 'F005', and/or 'F039' that is derived from 'F001' through 'F005' waste, be delisted. On June 13, 1995, the U.S. Environmental Protection Agency published the final rule (Final Delisting), which formally excluded 71.9 million liters per year of 200 Area Effluent Treatment Facility effluent from ''being listed as hazardous wastes'' (60 FR 31115 now promulgated in 40 CFR 261). Given the limited scope, it is necessary to request a modification of the Final Delisting to address the management of a more diverse multi-source leachate (F039) at the 200 Area Effluent Treatment Facility. From past operations and current cleanup activities on the Hanford Facility, a considerable amount of both liquid and solid Resource Conservation and Recovery Act of 1976 regulated mixed waste has been and continues to be generated. Ultimately this waste will be treated as necessary to meet the Resource Conservation and Recovery Act Land Disposal Restrictions. The disposal of this waste will be in Resource Conservation and Recovery Act--compliant permitted lined trenches equipped with leachate collection systems. These operations will result in the generation of what is referred to as multi-source leachate. This newly generated waste will receive the listed waste designation of F039. This waste also must be managed in compliance with the provisions of the Resource Conservation and Recovery Act.

  6. Degradation of different elastomeric polymers in simulated geothermal environments at 300°C

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Sugama, Toshifumi; Pyatina, Tatiana; Redline, Erica Marie; McElhanon, James R.; Blankenship, Douglas A.

    2015-07-17

    This study evaluates the degradation of six different elastomeric polymers used for O-rings: EPDM, FEPM, type I- and II-FKM, FFKM, and FSR, in five different simulated geothermal environments at 300 °C: 1) non-aerated steam/cooling cycles, 2) aerated steam/cooling cycles, 3) water-based drilling fluid, 4) CO2-rich geo-brine fluid, and, 5) heat–cool water quenching cycles. The factors assessed included the extent of oxidation, changes in thermal behavior, micro-defects, permeation of ionic species from the test environments into the O-rings, silicate-related scale-deposition, and changes in the O-rings' elastic modulus. The reliability of the O-rings to maintain their integrity depended on the elastomeric polymermore » composition and the exposure environment. FSR disintegrated while EPDM was oxidized only to some degree in all the environments, FKM withstood heat-water quenching but underwent chemical degradation, FEPM survived in all the environments with the exception of heat-water quenching where it underwent severe oxidation-induced degradation, and FFKM displayed outstanding compatibility with all the tested environments. This study discusses the degradation mechanisms of the polymers under the aforementioned conditions.« less

  7. Degradation of different elastomeric polymers in simulated geothermal environments at 300°C

    SciTech Connect (OSTI)

    Sugama, Toshifumi; Pyatina, Tatiana; Redline, Erica Marie; McElhanon, James R.; Blankenship, Douglas A.

    2015-07-17

    This study evaluates the degradation of six different elastomeric polymers used for O-rings: EPDM, FEPM, type I- and II-FKM, FFKM, and FSR, in five different simulated geothermal environments at 300 °C: 1) non-aerated steam/cooling cycles, 2) aerated steam/cooling cycles, 3) water-based drilling fluid, 4) CO2-rich geo-brine fluid, and, 5) heat–cool water quenching cycles. The factors assessed included the extent of oxidation, changes in thermal behavior, micro-defects, permeation of ionic species from the test environments into the O-rings, silicate-related scale-deposition, and changes in the O-rings' elastic modulus. The reliability of the O-rings to maintain their integrity depended on the elastomeric polymer composition and the exposure environment. FSR disintegrated while EPDM was oxidized only to some degree in all the environments, FKM withstood heat-water quenching but underwent chemical degradation, FEPM survived in all the environments with the exception of heat-water quenching where it underwent severe oxidation-induced degradation, and FFKM displayed outstanding compatibility with all the tested environments. This study discusses the degradation mechanisms of the polymers under the aforementioned conditions.

  8. Integrity assessment plan for PNL 300 area radioactive hazardous waste tank system. Final report

    SciTech Connect (OSTI)

    1996-03-01

    The Pacific Northwest Laboratory (PNL), operated by Battelle Memorial Institute under contract to the U.S. Department of Energy, operates tank systems for the U.S. Department of Energy, Richland Operations Office (DOE-RL), that contain dangerous waste constituents as defined by Washington State Department of Ecology (WDOE) Dangerous Waste Regulations, Washington Administrative Code (WAC) 173-303-040(18). Chapter 173-303-640(2) of the WAC requires the performance of integrity assessments for each existing tank system that treats or stores dangerous waste, except those operating under interim status with compliant secondary containment. This Integrity Assessment Plan (IAP) identifies all tasks that will be performed during the integrity assessment of the PNL-operated Radioactive Liquid Waste Systems (RLWS) associated with the 324 and 325 Buildings located in the 300 Area of the Hanford Site. It describes the inspections, tests, and analyses required to assess the integrity of the PNL RLWS (tanks, ancillary equipment, and secondary containment) and provides sufficient information for adequate budgeting and control of the assessment program. It also provides necessary information to permit the Independent, Qualified, Registered Professional Engineer (IQRPE) to approve the integrity assessment program.

  9. Degradation of different elastomeric polymers in simulated geothermal environments at 300C

    SciTech Connect (OSTI)

    Sugama, Toshifumi; Pyatina, Tatiana; Redline, Erica Marie; McElhanon, James R.; Blankenship, Douglas A.

    2015-07-17

    This study evaluates the degradation of six different elastomeric polymers used for O-rings: EPDM, FEPM, type I- and II-FKM, FFKM, and FSR, in five different simulated geothermal environments at 300 C: 1) non-aerated steam/cooling cycles, 2) aerated steam/cooling cycles, 3) water-based drilling fluid, 4) CO2-rich geo-brine fluid, and, 5) heatcool water quenching cycles. The factors assessed included the extent of oxidation, changes in thermal behavior, micro-defects, permeation of ionic species from the test environments into the O-rings, silicate-related scale-deposition, and changes in the O-rings' elastic modulus. The reliability of the O-rings to maintain their integrity depended on the elastomeric polymer composition and the exposure environment. FSR disintegrated while EPDM was oxidized only to some degree in all the environments, FKM withstood heat-water quenching but underwent chemical degradation, FEPM survived in all the environments with the exception of heat-water quenching where it underwent severe oxidation-induced degradation, and FFKM displayed outstanding compatibility with all the tested environments. This study discusses the degradation mechanisms of the polymers under the aforementioned conditions.

  10. Communication across 300 generations: deterring human interference with waste deposit sites

    SciTech Connect (OSTI)

    Tannenbaum, P.H.

    1984-04-01

    The conditions attendant on the deep land burial of nuclear waste products raise a number of possible scenarios to cover the necessary 10,000 years of burial. However, no matter what kind of futuristic scenario obtains, it is desirable to develop an information system indicating the locale and nature of the deposit site and the types of materials stored, along with forewarnings not to interefere with the sites. A variety of such informational sites are suggested. Attention then turns to the recipients of such messages, recognizing from the outset that the psychological/perceptual makeup of individuals across the next 300 or so generations is virtually impossible to predict, particularly since new technologies may well alter that makeup in the furture. Nevertheless, current evidence suggests that certain human characteristics may be considered universal, and that these suggest the incorporation of selected sign signification into the message system. There are other such characteristics that, while probably not intrinsic, can probably be acquired with a minimum of formal training. That still leaves much of the message content to be deliberately created and, hence, learned. The common trefoil or other developed biohazardous signs emerge as the best candidates for a generic base symbol for the buried material.

  11. Hanford Facility dangerous waste permit application, liquid effluent retention facility and 200 area effluent treatment facility

    SciTech Connect (OSTI)

    Coenenberg, J.G.

    1997-08-15

    The Hanford Facility Dangerous Waste Permit Application is considered to 10 be a single application organized into a General Information Portion (document 11 number DOE/RL-91-28) and a Unit-Specific Portion. The scope of the 12 Unit-Specific Portion is limited to Part B permit application documentation 13 submitted for individual, `operating` treatment, storage, and/or disposal 14 units, such as the Liquid Effluent Retention Facility and 200 Area Effluent 15 Treatment Facility (this document, DOE/RL-97-03). 16 17 Both the General Information and Unit-Specific portions of the Hanford 18 Facility Dangerous Waste Permit Application address the content of the Part B 19 permit application guidance prepared by the Washington State Department of 20 Ecology (Ecology 1987 and 1996) and the U.S. Environmental Protection Agency 21 (40 Code of Federal Regulations 270), with additional information needs 22 defined by the Hazardous and Solid Waste Amendments and revisions of 23 Washington Administrative Code 173-303. For ease of reference, the Washington 24 State Department of Ecology alpha-numeric section identifiers from the permit 25 application guidance documentation (Ecology 1996) follow, in brackets, the 26 chapter headings and subheadings. A checklist indicating where information is 27 contained in the Liquid Effluent Retention Facility and 200 Area Effluent 28 Treatment Facility permit application documentation, in relation to the 29 Washington State Department of Ecology guidance, is located in the Contents 30 Section. 31 32 Documentation contained in the General Information Portion is broader in 33 nature and could be used by multiple treatment, storage, and/or disposal units 34 (e.g., the glossary provided in the General Information Portion). Wherever 35 appropriate, the Liquid Effluent Retention Facility and 200 Area Effluent 36 Treatment Facility permit application documentation makes cross-reference to 37 the General Information Portion, rather than duplicating

  12. Hydrogeology of the 200 Areas low-level burial grounds: An interim report: Volume 2, Appendixes

    SciTech Connect (OSTI)

    Last, G.V.; Bjornstad, B.N.; Bergeron, M.P.; Wallace, D.W.; Newcomer, D.R.; Schramke, J.A.; Chamness, M.A.; Cline, C.S.; Airhart, S.P.; Wilbur, J.S.

    1989-01-01

    This report presents information derived form the installation of 35 ground-water monitoring wells around six low-level radioactive/hazardous waste burial grounds located in the 200 Areas of the Hanford Site in southeastern Washington State. This information was collected between May 20, 1987 and August 1, 1988. The contents of this report have been divided into two volumes. Volume 1 contains the main text. This Volume contains the appendixes, including data and supporting information that verify content and results found in the main text.

  13. Compilation of Earthquakes from 1850-2007 within 200 miles of the Idaho National Laboratory

    SciTech Connect (OSTI)

    N. Seth Carpenter

    2010-07-01

    An updated earthquake compilation was created for the years 1850 through 2007 within 200 miles of the Idaho National Laboratory. To generate this compilation, earthquake catalogs were collected from several contributing sources and searched for redundant events using the search criteria established for this effort. For all sets of duplicate events, a preferred event was selected, largely based on epicenter-network proximity. All unique magnitude information for each event was added to the preferred event records and these records were used to create the compilation referred to as “INL1850-2007”.

  14. Compatibility of an Ultraselective Microcatheter and Epirubicin Loaded 300–500-μm DC Bead in Ex Vivo Study

    SciTech Connect (OSTI)

    Fukuoka, Yasushi Tanaka, Toshihiro Nishiofuku, Hideyuki Sato, Takeshi Kichikawa, Kimihiko

    2015-10-15

    PurposeThe purpose of this study is to examine whether epirubicin loaded DC Bead 300–500 μm in size can pass through a 1.8-Fr ultraselective microcatheter in ex vivo study.MethodsEpirubicin (25 mg/1 mL) loaded 100–300 and 300–500 μm DC Bead were tested. Both sizes were diluted 5, 10, and 30 times using contrast material. Ultraselective microcatheter with the outer diameter of 1.8 Fr and the inner diameter of .017 inch (431.8 μm) was used. The diluted DC Bead was injected at a speed of 1 mL/min, and the pressure was continuously measured. The microspheres’ shapes after ejection were observed by a stereomicroscope.ResultsThe maximum pressure of contrast material alone was 8.40 ± 0.21 psi. The maximum pressure in 5, 10, and 30 times dilution groups of 100–300 μm were 9.67 ± 1.18, 9.25 ± 0.25, and 9.71 ± 0.28 psi, respectively, whereas 21.10 ± 10.2, 10.48 ± 2.14, 10.09 ± 0.37 psi, respectively in 300–500 μm groups. The maximum pressure in 5 times dilution group of 300–500 μm was significantly higher than the other groups (P < 0.05). In 300–500 μm, 4 of 10 measurements showed high pressure over 24 psi (the maximum value was 43.5 psi) in 5 times dilution group, whereas in 10 times and 30 times dilution groups, all measurements showed less than 12 psi. No damages of microspheres were found.ConclusionsEpirubicin loaded DC Bead 300–500 μm in size can pass through a 1.8-Fr ultraselective microcatheter. To avoid high resistance due to microspheres’ aggregation, dilution more than 10 times is needed.

  15. Identification and In-vivo Characterization of a Novel OhrR Transcriptional Regulator in Burkholderia xenovorans LB400

    SciTech Connect (OSTI)

    Nguyen, Tinh T.; Mart-Arbona, Ricardo; Hall, Richard S.; Maity, Tuhin; Valdez, Yolanda E.; Dunbar, John M.; Unkefer, Clifford J.; Unkefer, Pat J.

    2013-05-21

    Transcriptional regulators (TRs) are an important and versatile group of proteins, yet very little progress has been achieved towards the discovery and annotation of their biological functions. We have characterized a previously unknown organic hydroperoxide resistance regulator from Burkholderia xenovoransLB400, Bxe_B2842, which is homologous to E. colis OhrR. Bxe_B2842 regulates the expression of an organic hydroperoxide resistance protein (OsmC). We utilized frontal affinity chromatography coupled with mass spectrometry (FAC-MS) and electrophoretic mobility gel shift assays (EMSA) to identify and characterize the possible effectors of the regulation by Bxe_B2842. Without an effector, Bxe_B2842 binds a DNA operator sequence (DOS) upstream of osmC. FAC-MS results suggest that 2-aminophenol binds to the protein and is potentially an effector molecule. EMSA analysis shows that 2-aminophenol also attenuates the Bxe_B2842s affinity for its DOS. EMSA analysis also shows that organic peroxides attenuate Bxe_B2842/DOS affinity, suggesting that binding of the TR to its DOS is regulated by the two-cysteine mechanism, common to TRs in this family. Bxe_B2842 is the first OhrR TR to have both oxidative and effector-binding mechanisms of regulation. Our paper reveals further mechanistic diversity TR mediated gene regulation and provides insights into methods for function discovery of TRs.

  16. Identification and In-vivo Characterization of a Novel OhrR Transcriptional Regulator in Burkholderia xenovorans LB400

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Nguyen, Tinh T.; Martí-Arbona, Ricardo; Hall, Richard S.; Maity, Tuhin; Valdez, Yolanda E.; Dunbar, John M.; Unkefer, Clifford J.; Unkefer, Pat J.

    2013-05-21

    Transcriptional regulators (TRs) are an important and versatile group of proteins, yet very little progress has been achieved towards the discovery and annotation of their biological functions. We have characterized a previously unknown organic hydroperoxide resistance regulator from Burkholderia xenovoransLB400, Bxe_B2842, which is homologous to E. coli’s OhrR. Bxe_B2842 regulates the expression of an organic hydroperoxide resistance protein (OsmC). We utilized frontal affinity chromatography coupled with mass spectrometry (FAC-MS) and electrophoretic mobility gel shift assays (EMSA) to identify and characterize the possible effectors of the regulation by Bxe_B2842. Without an effector, Bxe_B2842 binds a DNA operator sequence (DOS) upstream ofmore » osmC. FAC-MS results suggest that 2-aminophenol binds to the protein and is potentially an effector molecule. EMSA analysis shows that 2-aminophenol also attenuates the Bxe_B2842’s affinity for its DOS. EMSA analysis also shows that organic peroxides attenuate Bxe_B2842/DOS affinity, suggesting that binding of the TR to its DOS is regulated by the two-cysteine mechanism, common to TRs in this family. Bxe_B2842 is the first OhrR TR to have both oxidative and effector-binding mechanisms of regulation. Our paper reveals further mechanistic diversity TR mediated gene regulation and provides insights into methods for function discovery of TRs.« less

  17. High 400?C operation temperature blue spectrum concentration solar junction in GaInN/GaN

    SciTech Connect (OSTI)

    Zhao, Liang; Detchprohm, Theeradetch; Wetzel, Christian

    2014-12-15

    Transparent wide gap junctions suitable as high temperature, high flux topping cells have been achieved in GaInN/GaN by metal-organic vapor phase epitaxy. In structures of 25 quantum wells (QWs) under AM1.5G illumination, an open circuit voltage of 2.1?V is achieved. Of the photons absorbed in the limited spectral range of <450?nm, 64.2% are converted to electrons collected at the contacts under zero bias. At a fill factor of 45%, they account for a power conversion efficiency of38.6%. Under concentration, the maximum output power density per sun increases from 0.49?mW/cm{sup 2} to 0.51?mW/cm{sup 2} at 40?suns and then falls 0.42?mW/cm{sup 2} at 150?suns. Under external heating, a maximum of 0.59?mW/cm{sup 2} is reached at 250?C. Even at 400?C, the device is fully operational and exceeds room temperature performance. A defect analysis suggests that significantly higher fill factors and extension into longer wavelength ranges are possible with further development. The results prove GaInN/GaN QW solar junctions a viable and rugged topping cell for concentrator photovoltaics with minimal cooling requirements. By capturing the short range spectrum, they reduce the thermal load to any conventional cells stacked behind.

  18. Variability and scaling of hydraulic properties for 200 Area soils, Hanford Site

    SciTech Connect (OSTI)

    Khaleel, R.; Freeman, E.J.

    1995-10-01

    Over the years, data have been obtained on soil hydraulic properties at the Hanford Site. Much of these data have been obtained as part of recent site characterization activities for the Environmental Restoration Program. The existing data on vadose zone soil properties are, however, fragmented and documented in reports that have not been formally reviewed and released. This study helps to identify, compile, and interpret all available data for the principal soil types in the 200 Areas plateau. Information on particle-size distribution, moisture retention, and saturated hydraulic conductivity (K{sub s}) is available for 183 samples from 12 sites in the 200 Areas. Data on moisture retention and K{sub s} are corrected for gravel content. After the data are corrected and cataloged, hydraulic parameters are determined by fitting the van Genuchten soil-moisture retention model to the data. A nonlinear parameter estimation code, RETC, is used. The unsaturated hydraulic conductivity relationship can subsequently be predicted using the van Genuchten parameters, Mualem`s model, and laboratory-measured saturated hydraulic conductivity estimates. Alternatively, provided unsaturated conductivity measurements are available, the moisture retention curve-fitting parameters, Mualem`s model, and a single unsaturated conductivity measurement can be used to predict unsaturated conductivities for the desired range of field moisture regime.

  19. Screening of Potential Remediation Methods for the 200-ZP-1 Operable Unit at the Hanford Site

    SciTech Connect (OSTI)

    Truex, Michael J.; Nimmons, Michael J.; Johnson, Christian D.; Dresel, P EVAN.; Murray, Christopher J.

    2006-08-07

    A screening-level evaluation of potential remediation methods for application to the contaminants of concern (COC) in the 200-ZP-1 Operable Unit at the Hanford Site was conducted based on the methods outlined in the Guidance for Conducting Remedial Investigations and Feasibility Studies under CERCLA Interim Final. The scope of this screening was to identify the most promising remediation methods for use in the more detailed analysis of remediation alternatives that will be conducted as part of the full feasibility study. The screening evaluation was conducted for the primary COC (potential major risk drivers). COC with similar properties were grouped for the screening evaluation. The screening evaluation was conducted in two primary steps. The initial screening step evaluated potential remediation methods based on whether they can be effectively applied within the environmental setting of the 200-ZP-1 Operable Unit for the specified contaminants. In the second step, potential remediation methods were screened using scoping calculations to estimate the scale of infrastructure, overall quantities of reagents, and conceptual approach for applying the method for each defined grouping of COC. Based on these estimates, each method was screened with respect to effectiveness, implementability, and relative cost categories of the CERCLA feasibility study screening process defined in EPA guidance.

  20. Hydrogeology of the 200 Areas low-level burial grounds: An interim report: Volume 1, Text

    SciTech Connect (OSTI)

    Last, G.V.; Bjornstad, B.N.; Bergeron, M.P.; Wallace, D.W.; Newcomer, D.R.; Schramke, J.A.; Chamness, M.A.; Cline, C.S.; Airhart, S.P.; Wilbur, J.S.

    1989-01-01

    This report presents information derived from the installation of 35 ground-water monitoring wells around six low-level radioactive/hazardous waste burial grounds located in the 200 Areas of the Hanford Site in southeastern Washington State. This information was collected between May 20, 1987 and August 1, 1988. The contents of this report have been divided into two volumes. This volume contains the main text. Volume 2 contains the appendixes, including data and supporting information that verify content and results found in the main text. This report documents information collected by the Pacific Northwest Laboratory at the request of Westinghouse Hanford Company. Presented in this report are the preliminary interpretations of the hydrogeologic environment of six low-level burial grounds, which comprise four waste management areas (WMAs) located in the 200 Areas of the Hanford Site. This information and its accompanying interpretations were derived from sampling and testing activities associated with the construction of 35 ground-water monitoring wells as well as a multitude of previously existing boreholes. The new monitoring wells were installed as part of a ground-water monitoring program initiated in 1986. This ground-water monitoring program is based on requirements for interim status facilities in compliance with the Resource Conservation and Recovery Act (1976).

  1. Advanced Micro Turbine System (AMTS) -C200 Micro Turbine -Ultra-Low Emissions Micro Turbine

    SciTech Connect (OSTI)

    Capstone Turbine Corporation

    2007-12-31

    In September 2000 Capstone Turbine Corporation commenced work on a US Department of Energy contract to develop and improve advanced microturbines for power generation with high electrical efficiency and reduced pollutants. The Advanced MicroTurbine System (AMTS) program focused on: (1) The development and implementation of technology for a 200 kWe scale high efficiency microturbine system (2) The development and implementation of a 65 kWe microturbine which meets California Air Resources Board (CARB) emissions standards effective in 2007. Both of these objectives were achieved in the course of the AMTS program. At its conclusion prototype C200 Microturbines had been designed, assembled and successfully completed field demonstration. C65 Microturbines operating on natural, digester and landfill gas were also developed and successfully tested to demonstrate compliance with CARB 2007 Fossil Fuel Emissions Standards for NOx, CO and VOC emissions. The C65 Microturbine subsequently received approval from CARB under Executive Order DG-018 and was approved for sale in California. The United Technologies Research Center worked in parallel to successfully execute a RD&D program to demonstrate the viability of a low emissions AMS which integrated a high-performing microturbine with Organic Rankine Cycle systems. These results are documented in AMS Final Report DOE/CH/11060-1 dated March 26, 2007.

  2. Characterization of the Hanford 300 area burial grounds. Final report: decontamination and decommissioning

    SciTech Connect (OSTI)

    Phillips, S.J.; Ames, L.L.; Fitzner, R.E.; Gee, G.W.; Sandness, G.A.; Simmons, C.S.

    1980-01-01

    Pacific Northwest Laboratory conducted a series of investigations at the Hanford Site to develop technologies for characterizing and monitoring radioactive waste burial facilities that could be used in determining appropriate decommissioning alternatives. Specific objectives were to develop unique functional geophysics, geochemical, soil physics, numerical modeling, and biological methodologies needed to better characterize and monitor buried radioactive waste disposal sites. To meet these objectives the project was divided into four tasks: Task I, Geophysical Evaluation - Geophysical surveys were taken to locate and define the gross composition of waste materials. Task II, Geochemical Analysis - The interaction of disposed radionuclides with geologic media was analyzed through an integrated radiochemical procedure. Task III, Fluid Transport and Modeling - Computer modeling of water migration in partially saturated groundwater systems was verified with actual data collected at a field test facility used to monitor micrometeorological and geohydrological energy and mass transfer factors. Task IV, Biological Transport - Several biological organisms were evaluated for potential radionuclide uptake and transport. Along with the four tasks, the project included a review of pertinent literature and regulatory issues that might affect the alternatives selected. Surveys were taken of the surrounding area and specific sites and operations. The overall results indicated that the 300 Area Burial Grounds have been adequate in containing radioactive waste. Based on the results of the project, the alternatives identified for decommissioning these sites are exhumation and translocation, entombment, perpetual care, and abandonment. Perpetual care (currently used) appears to be the best decommissioning alternative for these burial grounds at this time. However, another alternative may be selected depending on future waste management policies, plans, or activities.

  3. Treatability Test for Removing Technetium-99 from 200-ZP-1 Groundwater, Hanford Site

    SciTech Connect (OSTI)

    Byrnes, M.E.; Petersen, S.W. [Fluor Hanford, Inc., Soil and Groundwater Remediation Project, Richland, WA (United States); Tortoso, A. [U.S. Department of Energy, Richland Operations Office, Richland, WA (United States); Elliott, W.S. [Environmental Quality Management, Inc., Richland, WA (United States)

    2008-07-01

    The 200-ZP-1 Groundwater Operable Unit (OU) is one of two groundwater OUs located within the 200 West groundwater aggregate area of the Hanford Site. The primary risk-driving contaminants within the 200-ZP-1 OU include carbon tetrachloride and technetium-99 (Tc-99). A pump-and-treat system for this OU was initially installed in 1995 to control the 0.002 kg /m{sup 3} (2000 {mu}g/L) contour of the carbon tetrachloride plume. Carbon tetrachloride is removed from groundwater with the assistance of an air-stripping tower. Ten extraction wells and three injection wells operate at a combined rate of approximately 0.017m{sup 3}/s (17.03 L/s). In 2005, groundwater from two of the extraction wells (299-W15-765 and 299-W15-44) began to show concentrations greater than twice the maximum contaminant level (MCL) of Tc-99 (33,309 beq/m{sup 3} or 900 pCi/L). The Tc-99 groundwater concentrations from all ten of the extraction wells when mixed were more than one-half of the MCL and were slowly increasing. If concentrations continued to rise and the water remained untreated for Tc-99, there was concern that the water re-injected into the aquifer could exceed the MCL standard. Multiple treatment technologies were reviewed for selectively removing Tc-99 from the groundwater. Of the treatment technologies, only ion exchange was determined to be highly selective, commercially available, and relatively low in cost. Through research funded by the U.S. Department of Energy, the ion-exchange resin Purolite{sup R} A-530E1 was found to successfully remove Tc-99 from groundwater, even in the presence of competing anions. For this and other reasons, Purolite{sup R} A-530E ion exchange resin was selected for treatability testing. The treatability test required installing resin columns on the discharge lines from extraction wells 299-W15-765 and 299-W15-44. Preliminary test results have concluded that the Purolite{sup R} A-530E1 resin is effective at removing Tc-99 from groundwater to below

  4. Screening of Potential Remediation Methods for the 200-BP-5 Operable Unit at the Hanford Site

    SciTech Connect (OSTI)

    Truex, Michael J.; Dresel, P. EVAN; Nimmons, Michael J.; Johnson, Christian D.

    2006-09-21

    A screening-level evaluation of potential remediation methods for application to the contaminants of concern (COC) in the 200-BP-5 Operable Unit at the Hanford Site was conducted based on the methods outlined in the Guidance for Conducting Remedial Investigations and Feasibility Studies under CERCLA Interim Final (EPA 1988). The scope of this screening was to identify the most promising remediation methods for use in the more detailed analysis of remediation alternatives that will be conducted as part of the full feasibility study. The screening evaluation was conducted for the primary COC (potential major risk drivers) identified in the groundwater sampling and analysis plan for the operable unit (DOE/RL-2001-49, Rev. 1) with additions.

  5. Transition plan: Project C-018H, 200-E Area Effluent Treatment Facility

    SciTech Connect (OSTI)

    Connor, M.D.

    1994-09-29

    The purpose of this transition plan is to ensure an orderly transfer of project information to operations to satisfy Westinghouse Hanford Company (WHC) operational requirements and objectives, and ensure safe and efficient operation of Project C-018H, the 200-E Area Effluent Treatment Facility (ETF). This plan identifies the deliverables for Project C-018H upon completion of construction and turnover to WHC for operations, and includes acceptance criteria to objectively assess the adequacy of the contract deliverables in relation to present requirements. The scope of this plan includes a general discussion of the need for complete and accurate design basis documentation and design documents as project deliverables. This plan also proposes that a configuration management plan be prepared to protect and control the transferred design documents and reconstitute the design basis and design requirements, in the event that the deliverables and project documentation received from the contractor are less than adequate at turnover.

  6. An examination of abnormal grain growth in low strain nickel-200

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Underwood, O.; Madison, J.; Martens, R. M.; Thompson, G. B.; Welsh, S.; Evans, J.

    2016-06-21

    Here, this study offers experimental observation of the effect of low strain conditions (ε < 10%) on abnormal grain growth (AGG) in Nickel-200. At such conditions, stored mechanical energy is low within the microstructure enabling one to observe the impact of increasing mechanical deformation on the early onset of AGG compared to a control, or nondeformed, equivalent sample. The onset of AGG was observed to occur at specific pairings of compressive strain and annealing temperature and an empirical relation describing the influence of thermal exposure and strain content was developed. The evolution of low-Σ coincident site lattice (CSL) boundaries andmore » overall grain size distributions are quantified using electron backscatter diffraction preceding, at onset and during ensuing AGG, whereby possible mechanisms for AGG in the low strain regime are offered and discussed.« less

  7. Aluminum-blade development for the Mod-0A 200-kilowatt wind turbine

    SciTech Connect (OSTI)

    Linscott, B.S.; Shaltens, R.K.; Eggers, A.G.

    1981-12-01

    This report documents the operating experience with two aluminum blades used on the DOE/NASA Mod-0A 200-kilowatt wind turbine located at Clayton, New Mexico. Each Mod-0A aluminum blade is 59.9 feet long and weighs 2360 pounds. The aluminum Mod-0A blade design requirements, the selected design, fabrication procedures, and the blade analyses are discussed. A detailed chronology is presented on the operating experience of the Mod-0A aluminum blades used at Clayton, New Mexico. Blade structural damage was experienced. Inspection and damage assessment were required. Structural modifications that were incorporated to the blades successfully extended the useful operating life of the blades. The aluminum blades completed the planned 2 years of operation of the Clayton wind turbine. The blades were removed from service in August 1980 to allow testing of advanced technology wood composite blades.

  8. Viscosity of multi-component molten nitrate salts : liquidus to 200 degrees C.

    SciTech Connect (OSTI)

    Bradshaw, Robert W.

    2010-03-01

    The viscosity of molten salts comprising ternary and quaternary mixtures of the nitrates of sodium, potassium, lithium and calcium was determined experimentally. Viscosity was measured over the temperature range from near the relatively low liquidus temperatures of he individual mixtures to 200C. Molten salt mixtures that do not contain calcium nitrate exhibited relatively low viscosity and an Arrhenius temperature dependence. Molten salt mixtures that contained calcium nitrate were relatively more viscous and viscosity increased as the roportion of calcium nitrate increased. The temperature dependence of viscosity of molten salts containing calcium nitrate displayed curvature, rather than linearity, when plotted in Arrhenius format. Viscosity data for these mixtures were correlated by the Vogel-Fulcher- ammann-Hesse equation.

  9. Results of LEBT/MEBT reconfiguration at BNL 200 MeV LINAC

    SciTech Connect (OSTI)

    Raparia,D.; Alessi, J.; Briscoe, B.; Fite, J.; Gould, O.; Kponou, A.; Lo Destro, V.; Okamura, M.; Ritter, J.

    2009-05-04

    The low energy (35 keV) and medium energy (750 keV) transport lines for both polarized and unpolarized H{sup -} have been reconfigured to reduce the beam emittance and beam losses out of the 200 MeV Linac. The medium energy line in the original layout was 7 m long, and had ten quadrupoles, two beam choppers, and three bunchers. The bunchers were necessary to keep the beam bunched at the entrance of the Linac. About 35% beam loss occurred, and the emittance growth was several fold. In the new layout, the 750 keV line is only 0.7 m long, with three quads and one buncher. We will present the experimental result of the upgrade.

  10. Safety analysis -- 200 Area Savannah River Plant, F-Canyon Operations. Supplement 4

    SciTech Connect (OSTI)

    Beary, M.M.; Collier, C.D.; Fairobent, L.A.; Graham, R.F.; Mason, C.L.; McDuffee, W.T.; Owen, T.L.; Walker, D.H.

    1986-02-01

    The F-Canyon facility is located in the 200 Separations Area and uses the Purex process to recover plutonium from reactor-irradiated uranium. The irradiated uranium is normally in the form of solid or hollow cylinders called slugs. These slugs are encased in aluminum cladding and are sent to the F-Canyon from the Savannah River Plant (SRP) reactor areas or from the Receiving Basin for Offsite Fuels (RBOF). This Safety Analysis Report (SAR) documents an analysis of the F-Canyon operations and is an update to a section of a previous SAR. The previous SAR documented an analysis of the entire 200 Separations Area operations. This SAR documents an analysis of the F-Canyon and is one of a series of documents for the Separations Area as specified in the Savannah River Implementation Plans. A substantial amount of the information supporting the conclusions of this SAR is found in the Systems Analysis. Some F-Canyon equipment has been updated during the time between the Systems Analysis and this SAR and a complete description of this equipment is included in this report. The primary purpose of the analysis was to demonstrate that the F-Canyon can be operated without undue risk to onsite or offsite populations and to the environment. In this report, risk is defined as the expected frequency of an accident, multiplied by the resulting radiological consequence in person-rem. The units of risk for radiological dose are person-rem/year. Maximum individual exposure values have also been calculated and reported.

  11. Design of a self-aligned, wide temperature range (300 mK-300 K) atomic force microscope/magnetic force microscope with 10 nm magnetic force microscope resolution

    SciTech Connect (OSTI)

    Karc?, zgr; Dede, Mnir

    2014-10-01

    We describe the design of a wide temperature range (300 mK-300 K) atomic force microscope/magnetic force microscope with a self-aligned fibre-cantilever mechanism. An alignment chip with alignment groves and a special mechanical design are used to eliminate tedious and time consuming fibre-cantilever alignment procedure for the entire temperature range. A low noise, Michelson fibre interferometer was integrated into the system for measuring deflection of the cantilever. The spectral noise density of the system was measured to be ~12 fm/?Hz at 4.2 K at 3 mW incident optical power. Abrikosov vortices in BSCCO(2212) single crystal sample and a high density hard disk sample were imaged at 10 nm resolution to demonstrate the performance of the system.

  12. Evaluation and Screening of Remedial Technologies for Uranium at the 300-FF-5 Operable Unit, Hanford Site, Washington

    SciTech Connect (OSTI)

    Nimmons, Michael J.

    2007-08-01

    Pacific Northwest National Laboratory (PNNL) is presently conducting a re-evaluation of remedies addressing persistent dissolved uranium concentrations in the upper aquifer under the 300 Area of the Hanford Site in southeastern Washington State. This work is being conducted as a Phase III feasibility study for the 300-FF-5 Operable Unit on behalf of the U.S. Department of Energy. As part of the feasibility study process, a comprehensive inventory of candidate remedial technologies was conducted by PNNL. This report documents the identification and screening of candidate technologies. The screening evaluation was conducted in accordance with guidance and processes specified by U.S. Environmental Protection Agency regulations associated with implementation of the Comprehensive Environmental Response, Compensation, and Liability Act process.

  13. Final Hazard Categorization for the Remediation of Six 300-FF-2 Operable Unit Solid Waste Burial Grounds

    SciTech Connect (OSTI)

    J. D. Ludowise

    2006-12-12

    This report provides the final hazard categorization (FHC) for the remediation of six solid waste disposal sites (referred to as burial grounds) located in the 300-FF-2 Operable Unit (OU) on the Hanford Site. These six sites (618-1, 618-2, 618-3, 618-7, 618-8, and 618-13 Burial Grounds) were determined to have a total radionuclide inventory (WCH 2005a, WCH 2005d, WCH 2005e and WCH 2006b) that exceeds the DOE-STD-1027 Category 3 threshold quantity (DOE 1997) and are the subject of this analysis. This FHC document examines the hazards, identifies appropriate controls to manage the hazards, and documents the FHC and commitments for the 300-FF-2 Burial Grounds Remediation Project.

  14. Microsoft Word - Environmental Review of B832 Canyon at LLNL Site 300 2.24.11.doc

    National Nuclear Security Administration (NNSA)

    Department of Energy News Media Contact For Immediate Release John Belluardo February 25, 2011 (925) 422-2567 ENVIRONMENTAL REVIEW OF THE BUILDING 832 CANYON OPERABLE UNIT AT LAWRENCE LIVERMORE NATIONAL LABORATORY'S SITE 300 BY U.S. DEPARTMENT OF ENERGY/NATIONAL NUCLEAR SECURITY ADMINISTRATION STARTED Livermore, CA -- The U.S. Department of Energy (DOE) /National Nuclear Security Administration has begun the first Five-Year Review of its environmental cleanup of the Building 832 Canyon Operable

  15. Recommendation 229: Recommendation on the Preferred Alternative for the Proposed Plan for Water Treatment at Outfall 200 at Y-12 National Security Complex

    Office of Energy Efficiency and Renewable Energy (EERE)

    ORSSAB recommends the preferred alternative in the Proposed Plan for Water Treatment at Outfall 200 at Y-12.

  16. Performance assessment for the disposal of low-level waste in the 200 east area burial grounds

    SciTech Connect (OSTI)

    Wood, M.I., Westinghouse Hanford

    1996-08-15

    A performance assessment analysis was completed for the 200 East Area Low-Level Burial Grounds (LLBG) to satisfy compliance requirements in DOE Order 5820.2A. In the analysis, scenarios of radionuclide release from the 200 East Area Low-Level waste facility was evaluated. The analysis focused on two primary scenarios leading to exposure. The first was inadvertent intrusion. In this scenario, it was assumed that institutional control of the site and knowledge of the disposal facility has been lost. Waste is subsequently exhumed and dose from exposure is received. The second scenario was groundwater contamination.In this scenario, radionuclides are leached from the waste by infiltrating precipitation and transported through the soil column to the underlying unconfined aquifer. The contaminated water is pumped from a well 100 m downstream and consumed,causing dose. Estimates of potential contamination of the surrounding environment were developed and the associated doses to the maximum exposed individual were calculated. The doses were compared with performance objective dose limits, found primarily in the DOE order 5850.2A. In the 200 East Area LLBG,it was shown that projected doses are estimated to be well below the limits because of the combination of environmental, waste inventory, and disposal facility characteristics of the 200 East Area LLBG. Waste acceptance criteria were also derived to ensure that disposal of future waste inventories in the 200 East Area LLBG will not cause an unacceptable increase in estimated dose.

  17. A High Temperature (400 to 650oC) Secondary Storage Battery Based on Liquid Sodium and Potassium Anodes

    SciTech Connect (OSTI)

    Tao, Greg; Weber, Neill

    2007-06-08

    This STTR Phase I research program was on the development of high temperature (400 to 650 C), secondary batteries with roundtrip efficiency > 90% for integration with a 3 to 10 kW solid oxide fuel cell (SOFC) system. In fulfillment of this objective, advanced planar high temperature rechargeable batteries, comprised of an alkali metal ion conducting, highly refractory, beta'' alumina solid electrolyte (BASE) sandwiched between liquid sodium (or potassium) anode and liquid metal salt cathode, were developed at MSRI. The batteries have been successfully demonstrated at a working temperature as high as 600 C. To our knowledge, so far no work has been reported in the literature on planar rechargeable batteries based on BASE, and results obtained in Phase I for the very first time demonstrated the viability of planar batteries, though relatively low temperature tubular-based sodium-sulfur batteries and ZEBRA batteries have been actively developed by very limited non U.S. companies. The results of this Phase I work have fulfilled all the goals and stated objectives, and the achievements showed much promise for further, substantial improvements in battery design and performance. The important results of Phase I are briefly described in what follows: (1) Both Na-BASE and K-BASE discs and tubes have been successfully fabricated using MSRI's patented vapor phase process. Ionic conductivity measurements showed that Na-BASE had higher ionic conductivity than K-BASE, consistence with the literature. At 500 C, Na-BASE conductivity is 0.36 S/cm, which is more than 20 times higher than 8YSZ electrolyte used for SOFC at 800 C. The activation energy is 22.58 kJ/mol. (2) CuCl{sub 2}, FeCl{sub 2}, ZnCl{sub 2}, and AgCl were identified as suitable salts for Na/metal salt or K/metal salt electrochemical couples based on thermochemical data. Further open circuit voltage measurements matched those deduced from the thermochemical data. (3) Tubular cells with CuCl{sub 2} as the cathode and

  18. Characterization of decontamination and decommissioning wastes expected from the major processing facilities in the 200 Areas

    SciTech Connect (OSTI)

    Amato, L.C.; Franklin, J.D.; Hyre, R.A.; Lowy, R.M.; Millar, J.S.; Pottmeyer, J.A.; Duncan, D.R.

    1994-08-01

    This study was intended to characterize and estimate the amounts of equipment and other materials that are candidates for removal and subsequent processing in a solid waste facility when the major processing and handling facilities in the 200 Areas of the Hanford Site are decontaminated and decommissioned. The facilities in this study were selected based on processing history and on the magnitude of the estimated decommissioning cost cited in the Surplus Facilities Program Plan; Fiscal Year 1993 (Winship and Hughes 1992). The facilities chosen for this study include B Plant (221-B), T Plant (221-T), U Plant (221-U), the Uranium Trioxide (UO{sub 3}) Plant (224-U and 224-UA), the Reduction Oxidation (REDOX) or S Plant (202-S), the Plutonium Concentration Facility for B Plant (224-B), and the Concentration Facility for the Plutonium Finishing Plant (PFP) and REDOX (233-S). This information is required to support planning activities for current and future solid waste treatment, storage, and disposal operations and facilities.

  19. Strange Particle Production in $p+p$ Collisions at $\\sqrt{s}$= 200GeV

    SciTech Connect (OSTI)

    Abelev, B.I.; Adams, J.; Aggarwal, M.M.; Ahammed, Z.; Amonett,J.; Anderson, B.D.; Anderson, M.; Arkhipkin, D.; Averichev, G.S.; Bai,Y.; Balewski, J.; Barannikova, O.; Barnby, L.S.; Baudot, J.; Bekele, S.; Belaga, V.V.; Bellingeri-Laurikainen, A.; Bellwied, R.; Benedosso, F.; Bhardwaj, S.; Bhasin, A.; Bhati, A.K.; Bichsel, H.; Bielcik, J.; Bielcikova, J.; Bland, L.C.; Blyth, S.-L.; Bonner, B.E.; Botje, M.; Bouchet, J.; Brandin, A.V.; Bravar, A.; Bystersky, M.; Cadman, R.V.; Cai,X.Z.; Caines, H.; Calderon de la Barca Sanchez, M.; Castillo, J.; Catu,O.; Cebra, D.; Chajecki, Z.; Chaloupka, P.; Chattopadhyay, S.; Chen,H.F.; Chen, J.H.; Cheng, J.; Cherney, M.; Chikanian, A.; Christie, W.; Coffin, J.P.; Cormier, T.M.; Cosentino, M.R.; Cramer, J.G.; Crawford,H.J.; Das, D.; Das, S.; Daugherity, M.; de Moura, M.M.; Dedovich, T.G.; DePhillips, M.; Derevschikov, A.A.; Didenko, L.; Dietel, T.; Djawotho,P.; Dogra, S.M.; Dong, W.J.; Dong, X.; Draper, J.E.; Du, F.; Dunin, V.B.; Dunlop, J.C.; Dutta Mazumdar, M.R.; Eckardt, V.; Edwards, W.R.; Efimov,L.G.; Emelianov, V.; Engelage, J.; Eppley, G.; Erazmus, B.; Estienne, M.; Fachini, P.; Fatemi, R.; Fedorisin, J.; Filimonov, K.; Filip, P.; Finch,E.; Fine, V.; Fisyak, Y.; Fu, J.; Gagliardi, C.A.; Gaillard, L.; Ganti,M.S.; Ghazikhanian, V.; Ghosh, P.; Gonzalez, J.S.; Gorbunov, Y.G.; Gos,H.; Grebenyuk, O.; Grosnick, D.; Guertin, S.M.; Guimaraes, K.S.F.F.; Guo,Y.; Gupta,N.; Gutierrez, T.D.; Haag, B.; Hallman, T.J.; Hamed, A.; Harris, J.W.; He, W.; Heinz, M.; Henry, T.W.; Hepplemann, S.; Hippolyte,B.; Hirsch, A.; Hjort, E.; Hoffman, A.M.; Hoffmann, G.W.; Horner, M.J.; Huang, H.Z.; Huang, S.L.; Hughes, E.W.; Humanic, T.J.; Igo, G.; Jacobs,P.; Jacobs, W.W.; Jakl, P.; Jia, F.; Jiang, H.; Jones, P.G.; Judd, E.G.; Kabana, S.; Kang, K.; Kapitan, J.; Kaplan, M.; Keane, D.; Kechechyan, A.; Khodyrev, V.Yu.; Kim, B.C.; Kiryluk, J.; Kisiel, A.; Kislov, E.M.; Klein,S.R.; Kocoloski, A.; Koetke, D.D.; et al.

    2006-07-31

    We present strange particle spectra and yields measured atmid-rapidity in sqrt text s=200 GeV proton-proton (p+p) collisions atRHIC. We find that the previously observed universal transverse mass(mathrm mT \\equiv\\sqrt mathrm p_T 2+\\mathrm m2) scaling of hadronproduction in p+p collisions seems to break down at higher \\mt and thatthere is a difference in the shape of the \\mt spectrum between baryonsand mesons. We observe mid-rapidity anti-baryon to baryon ratios nearunity for Lambda and Xi baryons and no dependence of the ratio ontransverse momentum, indicating that our data do not yet reach thequark-jet dominated region. We show the dependence of the mean transversemomentum (\\mpt) on measured charged particle multiplicity and on particlemass and infer that these trends are consistent with gluon-jet dominatedparticle production. The data are compared to previous measurements fromCERN-SPS, ISR and FNAL experiments and to Leading Order (LO) and Next toLeading order (NLO) string fragmentation model predictions. We infer fromthese comparisons that the spectral shapes and particle yields from $p+p$collisions at RHIC energies have large contributions from gluon jetsrather than quark jets.

  20. Geotechnical, Hydrogeologic and Vegetation Data Package for 200-UW-1 Waste Site Engineered Surface Barrier Design

    SciTech Connect (OSTI)

    Ward, Andy L.

    2007-11-26

    Fluor Hanford (FH) is designing and assessing the performance of engineered barriers for final closure of 200-UW-1 waste sites. Engineered barriers must minimize the intrusion and water, plants and animals into the underlying waste to provide protection for human health and the environment. The Pacific Northwest National Laboratory (PNNL) developed Subsurface Transport Over Multiple Phases (STOMP) simulator is being used to optimize the performance of candidate barriers. Simulating barrier performance involves computation of mass and energy transfer within a soil-atmosphere-vegetation continuum and requires a variety of input parameters, some of which are more readily available than others. Required input includes parameter values for the geotechnical, physical, hydraulic, and thermal properties of the materials comprising the barrier and the structural fill on which it will be constructed as well as parameters to allow simulation of plant effects. This report provides a data package of the required parameters as well as the technical basis, rationale and methodology used to obtain the parameter values.

  1. 200 Area effluent treatment facility process control plan 98-02

    SciTech Connect (OSTI)

    Le, E.Q.

    1998-01-30

    This Process Control Plan (PCP) provides a description of the background information, key objectives, and operating criteria defining Effluent Treatment Facility (ETF) Campaign 98-02 as required per HNF-IP-0931 Section 37, Process Control Plans. Campaign 98-62 is expected to process approximately 18 millions gallons of groundwater with an assumption that the UP-1 groundwater pump will be shut down on June 30, 1998. This campaign will resume the UP-1 groundwater treatment operation from Campaign 97-01. The Campaign 97-01 was suspended in November 1997 to allow RCRA waste in LERF Basin 42 to be treated to meet the Land Disposal Restriction Clean Out requirements. The decision to utilize ETF as part of the selected interim remedial action of the 200-UP-1 Operable Unit is documented by the Declaration of the Record of Decision, (Ecology, EPA and DOE 1997). The treatment method was chosen in accordance with the Comprehensive Environmental Response, Compensation, and Liability Act of 1980 (CERCLA) as amended by the Superfund Amendments and Reauthorization Act of 1986 (SARA), the Hanford Federal Facility Agreement and Consent Order (known as the Tri-Party Agreement or TPA), and to the extent practicable, the National Oil and Hazardous Substances Pollution Contingency Plan (NCP).

  2. Final Report 200 MW L-Band Annular Beam Klystron for Accelerators

    SciTech Connect (OSTI)

    Read, Michael; Ferguson, Patrick; Ives, Lawrence; Song, Liqun; Carlsten, Bruce; Fazio, Michael

    2009-02-11

    This program developed a 200 MW, 1.3 GHz, Annular Beam Klystron (ABK) for accelerator systems. An ABK provides lower impedance than a conventional klystron, making it possible to produce higher RF powers with lower voltages. With a higher power per unit, fewer klystrons would be required for a large accelerator. Lower voltage also simplifies and reduces the cost of the power supply system. Both features will significantly lower the cost of an RF system. This device operates at 475 kV. The klystron uses a magnetron injection gun producing 1100 A in one microsecond pulses. Power is extracted into fundamental rectangular waveguide through two output windows. The predicted gain is approximately 45 dB with estimated efficiency of 45%. The klystron was assembled, but no facility was available for testing. Consequently, no high power performance measurements are available. Because the assembled klystron is approximately 15 feet long, it was disassembled for storage. It can be reassembled should a use materialize.

  3. Overview of Air Liquide refrigeration systems between 1.8 K and 200 K

    SciTech Connect (OSTI)

    Gondrand, C.; Durand, F.; Delcayre, F.; Crispel, S.; Baguer, G. M. Gistau

    2014-01-29

    Cryogenic refrigeration systems are necessary for numerous applications. Gas purification and distillation require temperatures between 15 K and 200 K depending on the application, space simulation chambers down to 15 K, superconductivity between 1.8 K and up to 75 K (magnets, cavities or HTS devices like cables, FCL, SMES, etc), Cold Neutron Sources between 15 and 20 K, etc. Air Liquide Advanced Technologies is designing and manufacturing refrigerators since 60 years to satisfy those needs. The step by step developments achieved have led to machines with higher efficiency and reliability. In 1965, reciprocating compressors and Joule Thomson expansion valves were used. In 1969, centripetal expanders began to be used. In 1980, oil lubricated screw compressors took the place of reciprocating compressors and a standard range of Claude cycle refrigerators was developed: the HELIAL series. 1980 was also the time for cryogenic centrifugal compressor development. In 2011, driven by the need for lower operational cost (high efficiency and low maintenance), cycle oil free centrifugal compressors on magnetic bearings were introduced instead of screw compressors. The power extracted by centripetal expanders was recovered. Based on this technology, a range of Turbo-Brayton refrigerators has been designed for temperatures between 40 K and 150 K. On-going development will enable widening the range of Turbo-Brayton refrigerators to cryogenic temperatures down to 15 K.. Cryogenic centrifugal circulators have been developed in order to answer to an increasing demand of 4 K refrigerators able to distribute cold power.

  4. 200-BP-1 Prototype Hanford Barrier -- 15 Years of Performance Monitoring

    SciTech Connect (OSTI)

    Ward, Anderson L.; Draper, Kathryn E.; Link, Steven O.; Clayton, Ray E.

    2011-09-30

    Monitoring is an essential component of engineered barrier system design and operation. A composite capacitive cover, including a capillary break and an evapotranspiration (ET) barrier at the Hanford Site, is generating data that can be used to help resolve these issues. The prototype Hanford barrier was constructed over the 216-B-57 Crib in 1994 to evaluate surface-barrier constructability, construction costs, and physical and hydrologic performance at the field scale. The barrier has been routinely monitored between November 1994 and September 1998 as part of a Comprehensive Environmental Response, Compensation, and Liability Act of 1980 (CERCLA) treatability test of barrier performance for the 200 BP 1 Operable Unit. Since FY 1998, monitoring has focused on a more limited set of key water balance, stability, and biotic parameters. In FY 2009, data collection was focused on: (1) water-balance monitoring, consisting of precipitation, runoff, soil moisture storage, and drainage measurements with evapotranspiration calculated by difference; (2) stability monitoring, consisting of asphalt-layer-settlement, basalt-side-slope-stability, and surface-elevation measurements; (3) vegetation dynamics; and (4) animal use. September 2009 marked 15 years since the start of monitoring and the collection of performance data. This report describes the results of monitoring activities during the period October 1, 2008, through September 30, 2009, and summarizes the 15 years of performance data collected from September 1994 through September 2009.

  5. Environmental Protection Department Operations and Regulatory Affairs Division Contingency Plan for Site 300 Waste Accumulation Area(s)

    SciTech Connect (OSTI)

    Levy, R

    2005-07-14

    This Contingency Plan identifies personnel responsibilities, emergency equipment, and required actions necessary to mitigate potential incidents at the Waste Accumulation Area(s) (WAA)(s) located at the Lawrence Livermore National Laboratory (LLNL) Experimental Test Site 300 (Site 300) as shown in Figure 1. This Plan is designed to prepare personnel to minimize hazards to human health and the environment from fires, explosions, or any sudden or nonsudden release of hazardous, radioactive, or mixed waste constituents to the air, ground surface, or water from waste stored in the WAA(s). The LLNL Site 300 currently has one WAA. The location of the WAA is shown in Figure 2 and identified in Table 1. As programmatic needs change, it may become necessary to establish additional WAAs at Site 300. The WAA is a small, regularly monitored storage area where waste can be accumulated and stored temporarily. Hazardous and mixed waste can be stored or accumulated in a WAA for up to 90 days, after which it must be transferred to a Department of Toxic Substances Control (DTSC) authorized onsite treatment or storage facility or an authorized offsite treatment, storage, or disposal facility (TSDF). The onsite TSDFs authorized by DTSC are managed by the Radioactive and Hazardous Waste Management (RHWM) Division and by the Chemistry and Materials Science Directorate (CMS) at Site 300. Hazardous, radioactive, or mixed waste is referred to as ''waste'' in this document. Radioactive waste has been included in this Plan as a ''Best Management Practice'' to aid in response, where appropriate. However, radioactive waste is not regulated by DTSC under this Plan. This Contingency Plan is divided into two parts: (1) The first part, referred to as the ''General Plan'', is general information that is applicable to the existing and any subsequent WAAs. The General Plan includes Sections 1-7 and Appendices A-C. (2) The second part, referred to as the ''Site-Specific Plan'', contains site

  6. C-H surface diamond field effect transistors for high temperature (400 °C) and high voltage (500 V) operation

    SciTech Connect (OSTI)

    Kawarada, H.; Tsuboi, H.; Naruo, T.; Yamada, T.; Xu, D.; Daicho, A.; Saito, T.; Hiraiwa, A.

    2014-07-07

    By forming a highly stable Al{sub 2}O{sub 3} gate oxide on a C-H bonded channel of diamond, high-temperature, and high-voltage metal-oxide-semiconductor field-effect transistor (MOSFET) has been realized. From room temperature to 400 °C (673 K), the variation of maximum drain-current is within 30% at a given gate bias. The maximum breakdown voltage (V{sub B}) of the MOSFET without a field plate is 600 V at a gate-drain distance (L{sub GD}) of 7 μm. We fabricated some MOSFETs for which V{sub B}/L{sub GD} > 100 V/μm. These values are comparable to those of lateral SiC or GaN FETs. The Al{sub 2}O{sub 3} was deposited on the C-H surface by atomic layer deposition (ALD) at 450 °C using H{sub 2}O as an oxidant. The ALD at relatively high temperature results in stable p-type conduction and FET operation at 400 °C in vacuum. The drain current density and transconductance normalized by the gate width are almost constant from room temperature to 400 °C in vacuum and are about 10 times higher than those of boron-doped diamond FETs.

  7. LITERATURE SURVEY FOR GROUNDWATER TREATMENT OPTIONS FOR NITRATE IODINE-129 AND URANIUM 200-ZP-1 OPERABLE UNIT HANFORD SITE

    SciTech Connect (OSTI)

    BYRNES ME

    2008-06-05

    This literature review presents treatment options for nitrate, iodine-129, and uranium, which are present in groundwater at the 200-ZP-I Groundwater Operable Unit (OU) within the 200 West Area of the Hanford Site. The objective of this review is to determine available methods to treat or sequester these contaminants in place (i.e., in situ) or to pump-and-treat the groundwater aboveground (i.e., ex situ). This review has been conducted with emphasis on commercially available or field-tested technologies, but theoretical studies have, in some cases, been considered when no published field data exist. The initial scope of this literature review included only nitrate and iodine-I 29, but it was later expanded to include uranium. The focus of the literature review was weighted toward researching methods for treatment of nitrate and iodine-129 over uranium because of the relatively greater impact of those compounds identified at the 200-ZP-I OU.

  8. RCRA facility investigation/corrective measures study work plan for the 200-UP-2 Operable Unit, Hanford Site, Richland, Washington

    SciTech Connect (OSTI)

    Not Available

    1993-06-01

    The 200-UP-2 Operable Unit is one of two source operable units at the U Plant Aggregate Area at the Hanford Site. Source operable units include waste management units and unplanned release sites that are potential sources of radioactive and/or hazardous substance contamination. This work plan, while maintaining the title RFI/CMS, presents the background and direction for conducting a limited field investigation in the 200-UP-2 Operable Unit, which is the first part of the process leading to final remedy selection. This report discusses the background, prior recommendations, goals, organization, and quality assurance for the 200-UP-2 Operable Unit Work Plan. The discussion begins with a summary of the regulatory framework and the role of the work plan. The specific recommendations leading into the work plan are then addressed. Next, the goals and organization of the report are discussed. Finally, the quality assurance and supporting documentation are presented.

  9. Remedial Investigation/Feasibility Study Work Plan for the 200-UP-1 Groundwater Operable Unit, Hanford Site, Richland, Washington. Revision

    SciTech Connect (OSTI)

    Not Available

    1994-01-01

    This work plan identifies the objectives, tasks, and schedule for conducting a Remedial Investigation/Feasibility Study for the 200-UP-1 Groundwater Operable Unit in the southern portion of the 200 West Groundwater Aggregate Area of the Hanford Site. The 200-UP-1 Groundwater Operable Unit addresses contamination identified in the aquifer soils and groundwater within its boundary, as determined in the 200 West Groundwater Aggregate Area Management Study Report (AAMSR) (DOE/RL 1992b). The objectives of this work plan are to develop a program to investigate groundwater contaminants in the southern portion of the 200 West Groundwater Aggregate Area that were designated for Limited Field Investigations (LFIs) and to implement Interim Remedial Measures (IRMs) recommended in the 200 West Groundwater AAMSR. The purpose of an LFI is to evaluate high priority groundwater contaminants where existing data are insufficient to determine whether an IRM is warranted and collect sufficient data to justify and implement an IRM, if needed. A Qualitative Risk Assessment (QRA) will be performed as part of the LFI. The purpose of an IRM is to develop and implement activities, such as contaminant source removal and groundwater treatment, that will ameliorate some of the more severe potential risks of groundwater contaminants prior to the RI and baseline Risk Assessment (RA) to be conducted under the Final Remedy Selection (FRS) at a later date. This work plan addresses needs of a Treatability Study to support the design and implementation of an interim remedial action for the Uranium-{sup 99}{Tc}-Nitrate multi-contaminant IRM plume identified beneath U Plant.

  10. Puerto Rico and U.S. Virgin Islands Wind Resource Map at 50 meters

    Wind Powering America (EERE)

    % % % % % % % % % % % % % % % % % % % % % 19-JUN-2007 1.1.1 U.S. Department of Energy National Renewable Energy Laboratory Puerto Rico and U.S. Virgin Islands - 50 m Wind Power Mayaguez 20 0 20 40 60 80 100 Kilometers 20 0 20 40 60 Miles Ponce San Juan Charlotte Amalie Cruz Bay PUERTO RICO VIRGIN ISLANDS Wind Power Class 1 2 3 4 5 Resource Potential Poor Marginal Fair Good Excellent Wind Power Density at 50 m W/m 0 - 200 200 - 300 300 - 400 400 - 500 500 - 600 2 Wind Speed at 50 m m/s 0.0 - 5.9

  11. Intercomparison of the seasonal cycle in 200 hPa kinetic energy in AMIP GCM simulations

    SciTech Connect (OSTI)

    Boyle, J.S.

    1996-10-01

    The 200 hPa kinetic energy is represented by means of the spherical harmonic components for the Atmospheric Model Intercomparison Project (AMIP) simulations, the National Center for Environmental Prediction/National Center for Atmospheric Research (NCEP/NCAR) reanalysis and the European Centre for Medium Range Weather Forecast Reanalysis (ERA). The data used are the monthly mean wind fields from 1979 to 1988. The kinetic energy is decomposed into the divergent (DKE) and rotational (RKE) components and emphasis is placed on examining the former. The two reanalysis data sets show reasonable agreement that is best for the rotational kinetic energy. The largest difference in the divergent kinetic energy occurs during the northern summer. As might be expected, the two analyses are closet in regions where there are sufficient observations such that the effect of the model used in the assimilation cycle are minimized. The observed RKE show only a slight seasonal cycle with a maximum occuring during the northern winter. The DKE, on the other hand, has a very pronounced seasonal cycle with maxima at the solsticial seasons and minima during the equinoctial seasons. The model results show a very large spread in the magnitudes of the RKE and DKE although the models all evince a seasonal variation in phase with that observed. The median values of the seasonal cycle of RKE and DKE for the models are usually superior to those of any individual model. Results are also presented for simulation following the AMIP protocol but using updated versions of the original AMIP entries. In most cases these new integrations show better agreement with the observations.

  12. Groundwater monitoring plan for the Hanford Site 200 Area Treated Effluent Disposal Facility

    SciTech Connect (OSTI)

    DB Barnett

    2000-05-17

    Seven years of groundwater monitoring at the 200 Area Treated Effluent Disposal Facility (TEDF) have shown that the uppermost aquifer beneath the facility is unaffected by TEDF effluent. Effluent discharges have been well below permitted and expected volumes. Groundwater mounding from TEDF operations predicted by various models has not been observed, and waterlevels in TEDF wells have continued declining with the dissipation of the nearby B Pond System groundwater mound. Analytical results for constituents with enforcement limits indicate that concentrations of all these are below Practical Quantitation Limits, and some have produced no detections. Likewise, other constituents on the permit-required list have produced results that are mostly below sitewide background. Comprehensive geochemical analyses of groundwater from TEDF wells has shown that most constituents are below background levels as calculated by two Hanford Site-wide studies. Additionally, major ion proportions and anomalously low tritium activities suggest that groundwater in the aquifer beneath the TEDF has been sequestered from influences of adjoining portions of the aquifer and any discharge activities. This inference is supported by recent hydrogeologic investigations which indicate an extremely slow rate of groundwater movement beneath the TEDF. Detailed evaluation of TEDF-area hydrogeology and groundwater geochemistry indicate that additional points of compliance for groundwater monitoring would be ineffective for this facility, and would produce ambiguous results. Therefore, the current groundwater monitoring well network is retained for continued monitoring. A quarterly frequency of sampling and analysis is continued for all three TEDF wells. The constituents list is refined to include only those parameters key to discerning subtle changes in groundwater chemistry, those useful in detecting general groundwater quality changes from upgradient sources, or those retained for comparison with end

  13. Preliminary Safety Analysis Report (PSAR), The NSLS 200 MeV Linear Electron Accelerator

    SciTech Connect (OSTI)

    Blumberg, L.N.; Ackerman, A.I.; Dickinson, T.; Heese, R.N.; Larson, R.A.; Neuls, C.W.; Pjerov, S.; Sheehan, J.F.

    1993-06-15

    The radiological, fire and electrical hazards posed by a 200 MeV electron Linear Accelerator, which the NSLS Department will install and commission within a newly assembled structure, are addressed in this Preliminary Safety Analysis Report. Although it is clear that this accelerator is intended to be the injector for a future experimental facility, we address only the Linac in the present PSAR since neither the final design nor the operating characteristics of the experimental facility are known at the present time. The fire detection and control system to be installed in the building is judged to be completely adequate in terms of the marginal hazard presented - no combustible materials other than the usual cabling associated with such a facility have been identified. Likewise, electrical hazards associated with power supplies for the beam transport magnets and accelerator components such as the accelerator klystrons and electron gun are classified as marginal in terms of potential personnel injury, cost of equipment lost, program downtime and public impact perceptions as defined in the BNL Environmental Safety and Health Manual and the probability of occurrence is deemed to be remote. No unusual features have been identified for the power supplies or electrical distribution system, and normal and customary electrical safety standards as practiced throughout the NSLS complex and the Laboratory are specified in this report. The radiation safety hazards are similarly judged to be marginal in terms of probability of occurrence and potential injury consequences since, for the low intensity operation proposed - a factor of 25 less than the maximum Linac capability specified by the vendor - the average beam power is only 0.4 watts. The shielding specifications given in this report will give adequate protection to both the general public and nonradiation workers in areas adjacent to the building as well as radiation workers within the controlled access building.

  14. Spectroscopic and thermodynamic properties of molecular hydrogen dissolved in water at pressures up to 200 MPa

    SciTech Connect (OSTI)

    Borysow, Jacek Rosso, Leonardo del; Celli, Milva; Ulivi, Lorenzo; Moraldi, Massimo

    2014-04-28

    We have measured the Raman Q-branch of hydrogen in a solution with water at a temperature of about 280 K and at pressures from 20 to 200 MPa. From a least-mean-square fitting analysis of the broad Raman Q-branch, we isolated the contributions from the four lowest individual roto-vibrational lines. The vibrational lines were narrower than the pure rotational Raman lines of hydrogen dissolved in water measured previously, but significantly larger than in the gas. The separations between these lines were found to be significantly smaller than in gaseous hydrogen and their widths were slightly increasing with pressure. The lines were narrowing with increasing rotational quantum number. The Raman frequencies of all roto-vibrational lines were approaching the values of gas phase hydrogen with increasing pressure. Additionally, from the comparison of the integrated intensity signal of Q-branch of hydrogen to the integrated Raman signal of the water bending mode, we have obtained the concentration of hydrogen in a solution with water along the 280 K isotherm. Hydrogen solubility increases slowly with pressure, and no deviation from a smooth behaviour was observed, even reaching thermodynamic conditions very close to the transition to the stable hydrogen hydrate. The analysis of the relative hydrogen concentration in solution on the basis of a simple thermodynamic model has allowed us to obtain the molar volume for the hydrogen gas/water solution. Interestingly, the volume relative to one hydrogen molecule in solution does not decrease with pressure and, at high pressure, is larger than the volume pertinent to one molecule of water. This is in favour of the theory of hydrophobic solvation, for which a larger and more stable structure of the water molecules is expected around a solute molecule.

  15. Atomic Number Dependence of Hadron Production at Large Transverse Momentum in 300 GeV Proton--Nucleus Collisions

    DOE R&D Accomplishments [OSTI]

    Cronin, J. W.; Frisch, H. J.; Shochet, M. J.; Boymond, J. P.; Mermod, R.; Piroue, P. A.; Sumner, R. L.

    1974-07-15

    In an experiment at the Fermi National Accelerator Laboratory we have compared the production of large transverse momentum hadrons from targets of W, Ti, and Be bombarded by 300 GeV protons. The hadron yields were measured at 90 degrees in the proton-nucleon c.m. system with a magnetic spectrometer equipped with 2 Cerenkov counters and a hadron calorimeter. The production cross-sections have a dependence on the atomic number A that grows with P{sub 1}, eventually leveling off proportional to A{sup 1.1}.

  16. Modeling the Thermal Mechanical Behavior of a 300 K Vacuum Vesselthat is Cooled by Liquid Hydrogen in Film Boiling

    SciTech Connect (OSTI)

    Yang, S.Q.; Green, M.A.; Lau, W.

    2004-05-07

    This report discusses the results from the rupture of a thin window that is part of a 20-liter liquid hydrogen vessel. This rupture will spill liquid hydrogen onto the walls and bottom of a 300 K cylindrical vacuum vessel. The spilled hydrogen goes into film boiling, which removes the thermal energy from the vacuum vessel wall. This report analyzes the transient heat transfer in the vessel and calculates the thermal deflection and stress that will result from the boiling liquid in contact with the vessel walls. This analysis was applied to aluminum and stainless steel vessels.

  17. Application of multifuel reburn for NOx control on a 300 MWe boiler in Ukraine. Report for October 1994--December 1995

    SciTech Connect (OSTI)

    Hall, R.E.; Miller, C.A.; Payne, R.; Yakushin, E.; Mospan, J.

    1996-01-01

    The paper gives results of a program to design two reburn systems for operation on 300 MWe, coal-fired utility boilers operating in Ukraine. One is a natural-gas-fired system designed by ABB Combustion Engineering, installed in September 1992, and continuing to operate with a 50 percent nitrogen oxides (NOx) reduction. The paper summarizes the natural gas reburn test results. Emphasis is placed on the second demonstration, a multifuel (natural gas, oil, and/or coal) reburn system for which a conceptual design has been completed by Energy and Environmental Research Corp. Engineering drawings are being prepared by the Karkov Design Bureau in Ukraine.

  18. Simulation of the deflection of 200- and 450-GeV protons by a bent germanium crystal

    SciTech Connect (OSTI)

    Koshcheev, V. P. Kholodov, A. K.; Morgun, D. A.

    2009-04-15

    It is shown that the result obtained by numerically solving the kinetic Fokker-Planck equation in the transverse-energy space on the basis of computer simulations of channeled-particle trajectories describes well the results of an experiment that studied the deflection of 200- and 450-GeV protons by a bent germanium crystal.

  19. Composite analysis for low-level waste disposal in the 200 area plateau of the Hanford Site

    SciTech Connect (OSTI)

    Kincaid, C.T.; Bergeron, M.P.; Cole, C.R.

    1998-03-01

    This report presents the first iteration of the Composite Analysis for Low-Level Waste Disposal in the 200 Area Plateau of the Hanford Site (Composite Analysis) prepared in response to the U.S. Department of Energy Implementation Plan for the Defense Nuclear Facility Safety Board Recommendation 94-2. The Composite Analysis is a companion document to published analyses of four active or planned low-level waste disposal actions: the solid waste burial grounds in the 200 West Area, the solid waste burial grounds in the 200 East Area, the Environmental Restoration Disposal Facility, and the disposal facilities for immobilized low-activity waste. A single Composite Analysis was prepared for the Hanford Site considering only sources on the 200 Area Plateau. The performance objectives prescribed in U.S. Department of Energy guidance for the Composite Analysis were 100 mrem in a year and examination of a lower dose (30 mrem in a year) to ensure the {open_quotes}as low as reasonably achievable{close_quotes} concept is followed. The 100 mrem in a year limit was the maximum allowable all-pathways dose for 1000 years following Hanford Site closure, which is assumed to occur in 2050. These performance objectives apply to an accessible environment defined as the area between a buffer zone surrounding an exclusive waste management area on the 200 Area Plateau, and the Columbia River. Estimating doses to hypothetical future members of the public for the Composite Analysis was a multistep process involving the estimation or simulation of inventories; waste release to the environment; migration through the vadose zone, groundwater, and atmospheric pathways; and exposure and dose. Doses were estimated for scenarios based on agriculture, residential, industrial, and recreational land use. The radionuclides included in the vadose zone and groundwater pathway analyses of future releases were carbon-14, chlorine-36, selenium-79, technetium-99, iodine-129, and uranium isotopes.

  20. Role for DNA methylation in the regulation of miR-200c and miR-141 expression in normal and cancer cells

    SciTech Connect (OSTI)

    Vrba, Lukas; Jensen, Taylor J.; Garbe, James C.; Heimark, Ronald L.; Cress, Anne E.; Dickinson, Sally; Stampfer, Martha R.; Futscher, Bernard W.

    2009-12-23

    BACKGROUND: The microRNA-200 family participates in the maintenance of an epithelial phenotype and loss of its expression can result in epithelial to mesenchymal transition (EMT). Furthermore, the loss of expression of miR-200 family members is linked to an aggressive cancer phenotype. Regulation of the miR-200 family expression in normal and cancer cells is not fully understood. METHODOLOGY/ PRINCIPAL FINDINGS: Epigenetic mechanisms participate in the control of miR-200c and miR-141 expression in both normal and cancer cells. A CpG island near the predicted mir-200c/mir-141 transcription start site shows a striking correlation between miR-200c and miR-141 expression and DNA methylation in both normal and cancer cells, as determined by MassARRAY technology. The CpG island is unmethylated in human miR-200/miR-141 expressing epithelial cells and in miR-200c/miR-141 positive tumor cells. The CpG island is heavily methylated in human miR-200c/miR-141 negative fibroblasts and miR-200c/miR-141 negative tumor cells. Mouse cells show a similar inverse correlation between DNA methylation and miR-200c expression. Enrichment of permissive histone modifications, H3 acetylation and H3K4 trimethylation, is seen in normal miR-200c/miR-141-positive epithelial cells, as determined by chromatin immunoprecipitation coupled to real-time PCR. In contrast, repressive H3K9 dimethylation marks are present in normal miR-200c/miR-141-negative fibroblasts and miR-200c/miR-141 negative cancer cells and the permissive histone modifications are absent. The epigenetic modifier drug, 5-aza-2'-deoxycytidine, reactivates miR-200c/miR-141 expression showing that epigenetic mechanisms play a functional role in their transcriptional control. CONCLUSIONS/ SIGNIFICANCE: We report that DNA methylation plays a role in the normal cell type-specific expression of miR-200c and miR-141 and this role appears evolutionarily conserved, since similar results were obtained in mouse. Aberrant DNA methylation of the

  1. Surface radiation survey for the Phase 1 remedial investigation of the 300-FF-1 operable unit on the Hanford Site

    SciTech Connect (OSTI)

    Teel, S.S.; Olsen, K.B.

    1990-10-01

    This report summarizes Task 3a-1 of the Phase I Remedial Investigation for the 300-FF-1 Operable Unit on the Hanford Site, near Richland, Washington. The purpose of the Remedial Investigation is to determine the nature and extent of the risk presented by releases of hazardous substances from the operable unit. The purpose of Task 3a-1 was to locate any areas of contaminated soil outside of operable unit waste facility boundaries. Surface radiation survey and sampling activities in the 300-FF-1 Operable Unit were conducted from September 1989 to December 1989 and April 1990 to June 1990. Surveys were conducted primarily using portable Geiger-Muller beta/gamma detectors. As a result, 77 locations were found where radiation occurred above a statistically calculated background estimate. The Ultra Sonic Ranging and Data System (USRADS) was also used to survey a limited area. Analysis of the USRADS data revealed several elevated measurements that were not detected at the same locations with the Geiger-Muller detector. 6 refs., 14 figs., 4 tabs.

  2. Surface radiation survey and soil sampling of the 300-FF-1 operable unit, Hanford Site, southeastern Washington: A case study

    SciTech Connect (OSTI)

    Teel, S.S.; Olsen, K.B.

    1990-10-01

    The methods used for conducting a radiological characterization of the soil surface for the Phase I Remedial Investigation of a Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA) site is presented via a case study. The study site is an operable unit (300-FF-1) located in and adjacent to the 300 Area of the US Department of Energy's Hanford Site in southeastern Washington State. The operable unit contains liquid and solid waste disposal facilities associated with nuclear fuels fabrication. Continuous surface radiation surveying and soil sampling of selected locations were conducted. Contamination was found in several locations within the operable unit including areas near the liquid and solid waste disposal facilities. Instruments used during surveying included portable beta/gamma (P-11) detectors, and the Ultrasonic Ranging and Data System using an NaI (Tl) detector. Laboratory analyses results indicate that above-background radiation levels were primarily due to the presence of uranium. Both types of field instruments used in the study were effective in detecting surface contamination from radionuclides; however, each had specific advantages. Guidelines are presented for the optimum use of these instruments when performing a radiological characterization of the soil surface. 4 refs., 3 figs., 3 tabs.

  3. Site 300 hazardous-waste-assessment project. Interim report: December 1981. Preliminary site reconnaissance and project work plan

    SciTech Connect (OSTI)

    Raber, E.; Helm, D.; Carpenter, D.; Peifer, D.; Sweeney, J.

    1982-01-20

    This document was prepared to outline the scope and objectives of the Hazardous Waste Assessment Project (HWAP) at Site 300. This project was initiated in October, 1981, to investigate the existing solid waste landfills in an effort to satisfy regulatory guidelines and assess the potential for ground-water contamination. This involves a site-specific investigation (utilizing geology, hydrology, geophysics and geochemistry) with the goal of developing an effective ground-water quality monitoring network. Initial site reconnaissance work has begun and we report the results, to date, of our geologic hydrogeologic studies. All known solid waste disposal locations are underlain by rocks of either the Late Miocene Neroly Formation or the Cierbo Formation, both of which are dominantly sandstones interbedded with shale and claystone. The existence of a regional confined (artesian) aquifer, as well as a regional water-table aquifer is postulated for Site 300. Preliminary analysis has led to an understanding of directions and depths of regional ground-water flow.

  4. Studies and optimization of Pohang Light Source-II superconducting radio frequency system at stable top-up operation with beam current of 400 mA

    SciTech Connect (OSTI)

    Joo, Youngdo Yu, Inha; Park, Insoo; Chun, Myunghwan; Lee, Byung-Joon; Hwang, Ilmoon; Ha, Taekyun; Shin, Seunghwan; Sohn, Younguk

    2014-12-21

    After three years of upgrading work, the Pohang Light Source-II (PLS-II) is now successfully operating. The final quantitative goal of PLS-II is a top-up user-service operation with beam current of 400 mA to be completed by the end of 2014. During the beam store test up to 400 mA in the storage ring (SR), it was observed that the vacuum pressure around the radio frequency (RF) window of the superconducting cavity rapidly increases over the interlock level limiting the availability of the maximum beam current storing. Although available beam current is enhanced by setting a higher RF accelerating voltage, it is better to keep the RF accelerating voltage as low as possible in the long time top-up operation. We investigated the cause of the window vacuum pressure increment by studying the changes in the electric field distribution at the superconducting cavity and waveguide according to the beam current. In our simulation, an equivalent physical modeling was developed using a finite-difference time-domain code. The simulation revealed that the electric field amplitude at the RF window is exponentially increased as the beam current increases, thus this high electric field amplitude causes a RF breakdown at the RF window, which comes with the rapid increase of window vacuum pressure. The RF accelerating voltage of PLS-II RF system was set to 4.95 MV, which was estimated using the maximum available beam current that works as a function of RF voltage, and the top-up operation test with the beam current of 400 mA was successfully carried out.

  5. A Geophysical Characterization & Monitoring Strategy for Determining Hydrologic Processes in the Hyporheic Corridor at the Hanford 300-Area

    SciTech Connect (OSTI)

    Slater, Lee; Day-Lewis, Frederick; Lane, John; Versteeg, Roelof; Ward, Anderson; Binley, Andrew; Johnson, Timothy; Ntarlagiannis, Dimitrios

    2011-08-31

    The primary objective of this research was to advance the prediction of solute transport between the Uranium contaminated Hanford aquifer and the Columbia River at the Hanford 300 Area by improving understanding of how fluctuations in river stage, combined with subsurface heterogeneity, impart spatiotemporal complexity to solute exchange along the Columbia River corridor. Our work explored the use of continuous waterborne electrical imaging (CWEI), in conjunction with fiber-optic distributed temperature sensor (FO-DTS) and time-lapse resistivity monitoring, to improve the conceptual model for how groundwater/surface water exchange regulates uranium transport. We also investigated how resistivity and induced polarization can be used to generate spatially rich estimates of the variation in depth to the Hanford-Ringold (H-R) contact between the river and the 300 Area Integrated Field Research Challenge (IFRC) site. Inversion of the CWEI datasets (a data rich survey containing {approx}60,000 measurements) provided predictions of the distributions of electrical resistivity and polarizability, from which the spatial complexity of the primary hydrogeologic units along the river corridor was reconstructed. Variation in the depth to the interface between the overlying coarse-grained, high permeability Hanford Formation and the underlying finer-grained, less permeable Ringold Formation, an important contact that limits vertical migration of contaminants, has been resolved along {approx}3 km of the river corridor centered on the IFRC site in the Hanford 300 Area. Spatial variability in the thickness of the Hanford Formation captured in the CWEI datasets indicates that previous studies based on borehole projections and drive-point and multi-level sampling likely overestimate the contributing area for uranium exchange within the Columbia River at the Hanford 300 Area. Resistivity and induced polarization imaging between the river and the 300 Area IFRC further imaged spatial

  6. INFLUENCE OF CARBON AND DPA RATE ON NEUTRON-INDUCED SWELLING OF Fe-15Cr-16Ni-0.25Ti IN FFTF AT ~400 DEGREES C

    SciTech Connect (OSTI)

    Okita, Taira; Sekimura, Naoto; Garner, Francis A.; Wolfer, W. G.

    2002-12-31

    The purpose of this effort is to determine the influence of dpa rate and composition on the void swelling of simple austenitic Fe-Cr-Ni alloys. Contrary to the swelling behavior of fcc Fe-15Cr-16Ni and Fe-15Cr-16Ni-0.25Ti alloys irradiated in the same FFTF-MOTA experiment, Fe-15Cr-16Ni-0.25Ti-0.04C does not exhibit a dependence of swelling on dpa rate at approximately 400 degrees C. The transient regime of swelling is prolonged by carbon addition, however.

  7. {open_quotes}In-situ{close_quotes} stress-relieving of Ni/Cu alloy 400 tubed high pressure feedwater heaters

    SciTech Connect (OSTI)

    Rahoi, D.W.

    1995-12-01

    One of the known failure methods of Ni/Cu Alloy 400 is stress-corrosion cracking. When it can be determined with physical evidence that this is occurring, it may be possible to arrest or, at least slow down the failure methods by performing an {open_quotes}in situ{close_quotes} stress relief using plant steam. This paper does not recommend how to do it, but does reveal there is some hope the relief-anneal slows down the failure rate and increases the heater life, by reducing residual stress.

  8. Performance assessment for the disposal of low-level waste in the 200 West Area Burial Grounds

    SciTech Connect (OSTI)

    Wood, M.I.; Khaleel, R.; Rittmann, P.D.; Lu, A.H.; Finfrock, S.H.; DeLorenzo, T.H. [Westinghouse Hanford Co., Richland, WA (United States); Serne, R.J.; Cantrell, K.J. [Pacific Northwest Lab., Richland, WA (United States)

    1995-06-01

    This document reports the findings of a performance assessment (PA) analysis for the disposal of solid low-level radioactive waste (LLW) in the 200 West Area Low-Level Waste Burial Grounds (LLBG) in the northwest corner of the 200 West Area of the Hanford Site. This PA analysis is required by US Department of Energy (DOE) Order 5820.2A (DOE 1988a) to demonstrate that a given disposal practice is in compliance with a set of performance objectives quantified in the order. These performance objectives are applicable to the disposal of DOE-generated LLW at any DOE-operated site after the finalization of the order in September 1988. At the Hanford Site, DOE, Richland Operations Office (RL) has issued a site-specific supplement to DOE Order 5820.2A, DOE-RL 5820.2A (DOE 1993), which provides additiona I ce objectives that must be satisfied.

  9. Addendum to Composite Analysis for Low-Level Waste Disposal in the 200 Area Plateau of the Hanford Site

    SciTech Connect (OSTI)

    Bergeron, Marcel P.; Freeman, Eugene J.; Wurstner, Signe K.; Kincaid, Charles T.; Coony, Mike M.; Strenge, Dennis L.; Aaberg, Rosanne L.; Eslinger, Paul W.

    2001-09-28

    This report summarizes efforts to complete an addendum analysis to the first iteration of the Composite Analysis for Low-Level Waste Disposal in the 200 Area Plateau of the Hanford Site (Composite Analysis). This document describes the background and performance objectives of the Composite Analysis and this addendum analysis. The methods used, results, and conclusions for this Addendum analysis are summarized, and recommendations are made for work to be undertaken in anticipation of a second analysis.

  10. Measurement of J/? Azimuthal Anisotropy in Au+Au Collisions at ?sNN=200 GeV

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Adamczyk, L.; Adkins, J. K.; Agakishiev, G.; Aggarwal, M. M.; Ahammed, Z.; Alekseev, I.; Alford, J.; Anson, C. D.; Aparin, A.; Arkhipkin, D.; et al

    2013-08-02

    The measurement of J/? azimuthal anisotropy is presented as a function of transverse momentum for different centralities in Au+Au collisions at ?sNN>/sub>=200 GeV. The measured J/? elliptic flow is consistent with zero within errors for transverse momentum between 2 and 10 GeV/c. Our measurement suggests that J/? particles with relatively large transverse momenta are not dominantly produced by coalescence from thermalized charm quarks, when comparing to model calculations.

  11. Calculation of nuclear data for incident energies to 200 MeV with the FKK-GNASH code system

    SciTech Connect (OSTI)

    Chadwick, M.B.; Young, P.G.

    1993-02-01

    We describe how the FKK-GNASH code system has been extended to calculate nucleon-induced reactions up to 200 MeV, and used to predict (p,xn) and (p,xp) cross sections on {sup 208}Pb at incident energies of 25, 45, 80 and 160 MeV, for an intermediate energy code intercomparison. Details of the reaction mechanisms calculated by FKK-GNASH are given, and the calculational procedure is described.

  12. Word Pro - Untitled1

    Gasoline and Diesel Fuel Update (EIA)

    Coal Production, 1949-2011 Total By Rank By Mining Method By Location 200 U.S. Energy Information Administration / Annual Energy Review 2011 Anthracite Lignite¹ Subbituminous Coal¹ ¹ Subbituminous coal and lignite are included in bituminous coal prior to 1969. Source: Table 7.2. 1950 1960 1970 1980 1990 2000 2010 0 300 600 900 1,200 1,500 Million Short Tons Bituminous Coal¹ 1950 1960 1970 1980 1990 2000 2010 0 200 400 600 800 Million Short Tons 1950 1960 1970 1980 1990 2000 2010 0 300 600

  13. ALSNews Vol. 300

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    a broad spectrum of other issues, including detectors; x-ray diffraction; graphene; influenza; nanomagnetism; next generation light sources; numerical modeling; quantum systems,...

  14. wgc300.tmp

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    | Short-Term Energy Outlook - March 2016 08-09 09-10 10-11 11-12 12-13 13-14 14-15 15-16 % Change Natural Gas Northeast Consumption (Mcf**) 80.3 75.7 80.7 66.4 76.1 84.0 84.7 69.9 -17.5 Price ($/mcf) 15.83 13.31 12.66 12.21 11.71 11.53 10.85 10.65 -1.8 Expenditures ($) 1,272 1,007 1,022 812 891 969 919 745 -19.0 Midwest Consumption (Mcf) 80.7 78.6 80.2 65.4 77.6 88.1 83.1 70.0 -15.8 Price ($/mcf) 11.47 9.44 9.23 8.99 8.36 8.69 8.55 7.37 -13.9 Expenditures ($) 926 742 740 587 648 766 711 516

  15. ALSNews Vol. 300

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    0 Print In This Issue Towards Heavy Fermions in Europium Intermetallic Compounds Stochastic Domain-Wall Depinning in Magnetic Nanowires ALS Gets $11.3 M in Stimulus Funds for Facility Improvements UEC Corner: Users' Meeting Workshops, Deadlines, and Elections DOE, UC Berkeley, and City of Berkeley Officials Visit Deadline for ALS Doctoral Fellowships Extended to Aug. 14 New Faces: Angel Hernandez Joins User Services Office Introducing: ALS Science Briefs Operations News Links UC Davis Physicist

  16. A detection-level hazardous waste ground-water monitoring compliance plan for the 200 areas low-level burial grounds and retrievable storage units

    SciTech Connect (OSTI)

    Not Available

    1987-02-01

    This plan defines the actions needed to achieve detection-level monitoring compliance at the Hanford Site 200 Areas Low-Level Burial Grounds (LLBG) in accordance with the Resource Conservation and Recovery Act (RCRA). Compliance will be achieved through characterization of the hydrogeology and monitoring of the ground water beneath the LLBG located in the Hanford Site 200 Areas. 13 refs., 20 figs.

  17. Report on the Threatened Valley Elderberry Longhorn Beetle and its Elderberry Food Plant at the Lawrence Livermore National Laboratory--Site 300

    SciTech Connect (OSTI)

    Arnold, Ph.D., R A; Woollett, J

    2004-11-16

    This report describes the results of an entomological survey in 2002 to determine the presence of the federally-listed, threatened Valley Elderberry Longhorn Beetle or ''VELB'' (Desmocerus culifornicus dimorphus: Coleoptera, Cerambycidae) and its elderberry food plant (Sumbucus mexicana: Caprifoliaceae) on the Lawrence Livermore National Laboratory's (LLNL) Experimental Test Site, known as Site 300. In addition, an area located immediately southeast of Site 300, which is owned and managed by the California Department of Fish and Game (CDFG), but secured by LLNL, was also included in this survey. This report will refer to the survey areas as the LLNL-Site 300 and the CDFG site. The 2002 survey included mapping the locations of elderberry plants that were observed using a global positioning system (GPS) to obtain positional coordinates for every elderberry plant at Site 300. In addition, observations of VELB adults and signs of their infestation on elderberry plants were also mapped using GPS technology. LLNL requested information on the VELB and its elderberry food plants to update earlier information that had been collected in 1991 (Arnold 1991) as part of the 1992 EIS/EIR for continued operation of LLNL. No VELB adults were observed as part of this prior survey. The findings of the 2002 survey reported herein will be used by LLNL as it updates the expected 2004 Environmental Impact Statement for ongoing operations at LLNL, including Site 300.

  18. Optimal Sizing of Energy Storage and Photovoltaic Power Systems for Demand Charge Mitigation (Poster), NREL (National Renewable Energy Laboratory)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    FUTURE WORK CONCLUSIONS 50.0% 40.0% 30.0% 20.0% 10.0% 00.0% Facility 1 Facility 2 Facility 3 Facility 4 Facility 5 $100/kW, $100/kWh $300/kW, $100/kWh $300/kW, $300/kWh This presentation does not contain any proprietary, confi dential, or otherwise restricted information NREL/PO-5400-60291 * This activity is funded by the DOE Vehicle Technologies Offi ce, Energy Storage Technology * We appreciate the support provided by DOE program managers - David Howell - Brian Cunningham * Technical questions

  19. ARM - 1999 ARM Science Team Meeting

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    ... Data System Orientation: The Use of ARM Data 2:00 - 4:00 p.m. Working Group Breakout Sessions Cross-Cutting Issues Meetings UAV ST Meeting 3:00 - 5:00 p.m. ARM Common Data ...

  20. Slide 1

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    - diffusion capacitance C T (V) - transition capacitance V ac - arcing AC voltage - signal frequency -8.00E+03 -7.00E+03 -6.00E+03 -5.00E+03 -4.00E+03 -3.00E+03 -2.00E+03...

  1. Coos Bay Field Gulf Coast Coal Region Williston Basin Illinois

    Gasoline and Diesel Fuel Update (EIA)

    C e n t r a l A p p a l a c h i a n B a s i n Michigan Basin Greater Green River Basin ... Coalbed Methane Fields, Lower 48 States 0 200 400 100 300 Miles Source: Energy ...

  2. BPA-2011-00698-FOIA Response

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    1211 16:00 1211 17:00 1211 18:00 1211 19:00 1211 20:00 1211 21:00 1211 22:00 1211 23:00 1311 0:00 1311 1:00 1311 2:00 1311 3:00 1311 4:00 1311 5:00...

  3. Dielectron Azimuthal Anisotropy at mid-rapidity in Au+Au collisions at root s=200GeV

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Adamczyk, L.

    2014-12-11

    We report on the first measurement of the azimuthal anisotropy (v₂) of dielectrons (e⁺e⁻ pairs) at mid-rapidity from √(sNN)=200 GeV Au + Au collisions with the STAR detector at the Relativistic Heavy Ion Collider (RHIC), presented as a function of transverse momentum (pT) for different invariant-mass regions. In the mass region Meeee<2.9GeV/c², the measured dielectron v₂ is consistent, within experimental uncertainties, with that from the cc¯ contributions.

  4. Electrically driven single photon emission from a CdSe/ZnSSe single quantum dot at 200?K

    SciTech Connect (OSTI)

    Quitsch, Wolf; Kmmell, Tilmar; Bacher, Gerd; Gust, Arne; Kruse, Carsten; Hommel, Detlef

    2014-09-01

    High temperature operation of an electrically driven single photon emitter based on a single epitaxial quantum dot is reported. CdSe/ZnSSe/MgS quantum dots are embedded into a p-i-n diode architecture providing almost background free excitonic and biexcitonic electroluminescence from individual quantum dots through apertures in the top contacts. Clear antibunching with g{sup 2}(??=?0)?=?0.28??0.20 can be tracked up to T?=?200?K, representing the highest temperature for electrically triggered single photon emission from a single quantum dot device.

  5. ΛΛ correlation function in Au + Au collisions at √sNN = 200 GeV

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Adamczyk, L.

    2015-01-12

    In this study, we present ΛΛ correlation measurements in heavy-ion collisions for Au+Au collisions at √sNN = 200 GeV using the STAR experiment at the Relativistic Heavy-Ion Collider (RHIC). The Lednický-Lyuboshitz analytical model has been used to fit the data to obtain a source size, a scattering length and an effective range. Implications of the measurement of the ΛΛ correlation function and interaction parameters for di-hyperon searches are discussed.

  6. Three-Dimensional Surface Geophysical Exploration of the 200-Series Tanks at the 241-C Tank Farm

    SciTech Connect (OSTI)

    Crook, N.; McNeill, M.; Dunham, Ralph; Glaser, Danney R.

    2014-02-26

    A surface geophysical exploration (SGE) survey using direct current electrical resistivity was conducted within the C Tank Farm in the vicinity of the 200-Series tanks at the Hanford Site near Richland, Washington. This survey was the second successful SGE survey to utilize the Geotection(TM)-180 Resistivity Monitoring System which facilitated a much larger survey size and faster data acquisition rate. The primary objective of the C Tank Farm SGE survey was to provide geophysical data and subsurface imaging results to support the Phase 2 RCRA Facility Investigation, as outlined in the Phase 2 RCRA Facility Investigation / Corrective Measures work plan RPP-PLAN-39114.

  7. Drilling Specifications: Well Installations in the 300 Area to Support PNNL’s Integrated Field-Scale Subsurface Research Challenge (IFC) Project

    SciTech Connect (OSTI)

    Bjornstad, Bruce N.; Vermeul, Vince R.

    2008-01-21

    Part of the 300 Area Integrated Field-Scale Subsurface Research Challenge (IFC) will be installation of a network of high density borings and wells to monitor migration of fluids and contaminants (uranium), both in groundwater and vadose zone, away from an surface infiltration plot (Figure A-1). The infiltration plot will be located over an area of suspected contamination at the former 300 Area South Process Pond (SPP). The SPP is located in the southeastern portion of the Hanford Site, within the 300-FF-5 Operable Unit. Pacific Northwest National Laboratory (PNNL) with the support of FH shall stake the well locations prior to the start of drilling. Final locations will be based on accessibility and will avoid any surface or underground structures or hazards as well as surface contamination.

  8. Application of Maximum Likelihood Bayesian Model Averaging to Groundwater Flow and Transport at the Hanford Site 300 Area

    SciTech Connect (OSTI)

    Meyer, Philip D.; Ye, Ming; Neuman, Shlomo P.; Rockhold, Mark L.

    2008-06-01

    A methodology to systematically and quantitatively assess model predictive uncertainty was applied to saturated zone uranium transport at the 300 Area of the U.S. Department of Energy Hanford Site in Washington State, USA. The methodology extends Maximum Likelihood Bayesian Model Averaging (MLBMA) to account jointly for uncertainties due to the conceptual-mathematical basis of models, model parameters, and the scenarios to which the models are applied. Conceptual uncertainty was represented by postulating four alternative models of hydrogeology and uranium adsorption. Parameter uncertainties were represented by estimation covariances resulting from the joint calibration of each model to observed heads and uranium concentration. Posterior model probability was dominated by one model. Results demonstrated the role of model complexity and fidelity to observed system behavior in determining model probabilities, as well as the impact of prior information. Two scenarios representing alternative future behavior of the Columbia River adjacent to the site were considered. Predictive simulations carried out with the calibrated models illustrated the computation of model- and scenario-averaged predictions and how results can be displayed to clearly indicate the individual contributions to predictive uncertainty of the model, parameter, and scenario uncertainties. The application demonstrated the practicability of applying a comprehensive uncertainty assessment to large-scale, detailed groundwater flow and transport modelling.

  9. Environmental Controls on the Activity of Aquifer Microbial Communities in the 300 Area of the Hanford Site

    SciTech Connect (OSTI)

    Konopka, Allan; Plymale, Andrew E.; Carvajal, Denny A.; Lin, Xueju; McKinley, James P.

    2013-11-06

    Aquifer microbes in the 300 Area of the Hanford Site in southeastern Washington State, USA are periodically exposed to U(VI) concentrations that can range up to 10 ?M in small sediment fractures. Assays of 35 H-leucine incorporation indicated that both sediment-associated and planktonic microbes were metabolically active, and that organic C was growth-limiting in the sediments. Although bacteria suspended in native groundwater retained high activity when exposed to 100 ?M U(VI), they were inhibited by U(VI) < 1 ?M in synthetic groundwater that lacked added bicarbonate. Chemical speciation modeling suggested that positively-charged species and particularly (UO2)3(OH)5+ rose in concentration as more U(VI) was added to synthetic groundwater, but that carbonate complexes dominated U(VI) speciation in natural groundwater. U toxicity was relieved when increasing amounts of bicarbonate were added to synthetic groundwater containing 4.5 ?M U(VI). Pertechnetate, an oxyanion that is another contaminant of concern at the Hanford Site, was not toxic to groundwater microbes at concentrations up to 125 ?M.

  10. Current flow and efficiencies of concentrator InGaP/GaAs/Ge solar cells at temperatures below 300K

    SciTech Connect (OSTI)

    Kalinovsky, Vitaly S. Kontrosh, Evgeny V. Dmitriev, Pavel A. Pokrovsky, Pavel V. Chekalin, Alexander V. Andreev, Viacheslav M.

    2014-09-26

    The forward dark current density voltage (J-V) characteristic is one of the most important characteristics of multi-junction solar cells. It indicates that the mechanisms of current flow in the space charge region of photoactive p-n junctions. If one is to idealize the optical and electrical (coupling) elements of the solar cells, it is the J-V characteristic that determines the theoretically possible efficiency of the solar cell. In this paper, using the connection between the dark J-V and photovoltaic (?-J{sub g}) efficiency generated current density characteristics, the effect of current transport mechanisms in the space charge on the efficiency of multi-junction solar cells was investigated in the temperature range of 300 80 K. In the experimental J-V and ?-J{sub g} curves of the multi-junction solar cells, segments corresponding to the dominant current transport mechanisms were identified. The developed method, based on the analysis of forward dark J-V characteristics, makes it possible to identify the parameters affecting the efficiency of the multi-junction solar cells in a wide range of temperatures and solar radiation concentration.

  11. Raman spectral studies of aqueous zinc bromide solutions to 300/sup 0/C at pressures of 9 MPa

    SciTech Connect (OSTI)

    Yang, M.M.; Crerar, D.A.; Irish, D.E.

    1988-08-01

    A Raman spectral study of 14 solutions of varying bromide to zinc ratios was conducted up to 300/sup 0/C and 9 MPa. The tetra-, tri-, di- as well as the mono-bromozinc complexes were identified. The signal from the ZnBr/sup +/ complex increased in intensity as temperature increased, for solutions of low bromide- to-zinc ratios. The ZnBr/sub 4//sup 2 -/ species was favored at higher Br/Zn ratios, and higher temperatures favored the formation of the species ZnBr/sub 2/ and ZnBr/sup +/ at the expense of ZnBr/sub 4//sup 2 -/ and ZnBr/sub 3//sup -/. Although solvated water is probably present in these zinc-bromo complexes, they found no evidence of O-Zn vibrations other than for Zn(H/sub 2/O)/sub 6//sup 2 +/. However, spectra of successive dilutions of solutions with high bromide to zinc ratios show a relative change in species populations thereby suggesting that water activity plays a decisive role in complex formation. For the first time trifluoromethanesulfonic acid (HTFMS) has been used as an internal standard in Raman spectroscopy. This permitted quantitative measurement of stepwise stability constants.

  12. Mechanical Response of Stitched T300 Mat/Urethane 420 IMR Composite Laminates: Property/Orientation Dependence and Damage Evolution

    SciTech Connect (OSTI)

    Deng, S.; Weitsman, Y.J.

    2000-03-01

    This report presents experimental and analytical results of investigations on the mechanical response of stitched T300 mat/urethane 420 IMR composite laminates with three different lay-up configurations. Tensile tests and short-term creep and recovery tests were conducted on the laminate coupons at various orientations. The X-ray photographic technique was adopted to detect the internal damage due to external loading history. The tensile data of laminates with antisymmetric and symmetric lay-ups indicated that lay- up sequences of cross-ply laminates do not have much influence on their tensile properties. However, misalignments within the stitch-bonded plies disturb the symmetry of intended quasi-isotropic laminates and thereby cause the mechanical properties to exhibit a certain amount of angular dependence. Classic lamination theory was found to be able to provide a very good prediction of tensile properties for the stitched laminates within linear range. Creep and recovery response of laminate coupons is greatly dependent on loading angles and load levels. The internal damage of laminate coupons is also directly related to loading angles and load levels as well as loading history.

  13. HEDL FACILITIES CATALOG 400 AREA

    SciTech Connect (OSTI)

    MAYANCSIK BA

    1987-03-01

    The purpose of this project is to provide a sodium-cooled fast flux test reactor designed specifically for irradiation testing of fuels and materials and for long-term testing and evaluation of plant components and systems for the Liquid Metal Reactor (LMR) Program. The FFTF includes the reactor, heat removal equipment and structures, containment, core component handling and examination, instrumentation and control, and utilities and other essential services. The complex array of buildings and equipment are arranged around the Reactor Containment Building.

  14. Identified high-pT spectra in Cu+Cu collisions at sqrt sNN=200 GeV

    SciTech Connect (OSTI)

    STAR Collaboration; Abelev, Betty

    2010-07-05

    We report new results on identified (anti)proton and charged pion spectra at large transverse momenta (3 < p{sub T} < 10 GeV/c) from Cu+Cu collisions at {radical}s{sub NN} = 200 GeV using the STAR detector at the Relativistic Heavy Ion Collider (RHIC). This study explores the system size dependence of two novel features observed at RHIC with heavy ions: the hadron suppression at high-p{sub T} and the anomalous baryon to meson enhancement at intermediate transverse momenta. Both phenomena could be attributed to the creation of a new form of QCD matter. The results presented here bridge the system size gap between the available pp and Au+Au data, and allow the detailed exploration for the on-set of the novel features. Comparative analysis of all available 200 GeV data indicates that the system size is a major factor determining both the magnitude of the hadron spectra suppression at large transverse momenta and the relative baryon to meson enhancement.

  15. Effect of 200 keV Ar{sup +} implantation on optical and electrical properties of polyethyleneterepthalate (PET)

    SciTech Connect (OSTI)

    Kumar, Rajiv Goyal, Meetika Sharma, Ambika; Aggarwal, Sanjeev; Sharma, Annu; Kanjilal, D.

    2015-05-15

    In the present paper we have discussed the effect of 200 keV Ar{sup +} ions on the electrical and optical properties of PET samples. PET samples were implanted with 200 keV Ar{sup +} ions to various doses ranging from 1×10{sup 15} to 1×10{sup 17} Ar{sup +} cm{sup 2}. The changes in the electrical and optical properties of pristine and implanted PET specimens have been studied by using Keithley electrometer and UV-Visible absorption spectroscopy. The electrical conductivity has found to be increased with increasing ion dose. The optical studies have revealed the drastic alterations in optical band gap from 3.63 eV to 1.48 eV and also increase in number of carbon atoms per cluster from 215 to 537. Further, the change in the electrical conductivity and optical band gap has also been correlated with the formation of conductive islands in the implanted layers of PET.

  16. Uranium Contamination in the 300 Area: Emergent Data and their Impact on the Source Term Conceptual Model

    SciTech Connect (OSTI)

    Brown, Christopher F.; Um, Wooyong; Serne, R. Jeffrey

    2008-09-30

    The primary objectives of this characterization activity were to: 1) determine the extent of uranium contamination in the sediments, 2) quantify the leachable (labile) concentration of uranium in the sediments, and 3) create a data set that could be used to correlate the present data to existing 300 Area data. In order to meet these objectives, sediments collected from wells 399-2-5 (C5708), 299-3-22 (C5706) and 299-4-14 (C5707) were analyzed for moisture content, 1:1 sediment:water extracts (which provide soil pH, electrical conductivity [EC], cation, and anion data), total carbon and inorganic carbon content, 8 M nitric acid extracts (which provide a measure of the total leachable sediment content of the contaminants), microwave-assisted digestion (which results in total digestion of the sediment), and carbonate leaches (which provide an assessment of the concentration of labile uranium present in the sediments). Additionally, pore waters present in select samples were extracted using ultracentrifugation. The mobility characteristics of uranium vary within the multiple subsurface zones that contain residual contaminant uranium. Principal subsurface zones include 1) the vadose zone, 2) a zone through which the water table rises and falls, 3) the aquifer, and 4) a zone where groundwater and river water interact beneath the river shoreline. Principal controls on mobilization include the form of the residual uranium (e.g., crystalline minerals, amorphous precipitates/coatings, sorbed onto sediment), the transporting medium (e.g., water infiltration from the land surface, groundwater), and the rate of exchange between the form and transporting medium. The bicarbonate content of aqueous media strongly influences the rate of exchange, with relatively higher content enhancing mobility. Groundwater has a higher bicarbonate content than river water or other freshwater sources, such as utility and potable water systems. The variety of processes affecting the mobility of

  17. Conversion of CH4 into H2 at 300 C using Pd/MnO2 catalyst made with an effect of water oxidation

    SciTech Connect (OSTI)

    Koyanaka, Hideki; Takeuchi, K; Kolesnikov, Alexander I

    2014-01-01

    A novel electricity-free deposition of palladium on the surface of manganese dioxide, which has a crystal structure of ramsdellite, was studied. Using the Pd deposition, a nano-particle of Pd/MnO2 was prepared, and it was used for a catalytic performance for reforming methane into hydrogen at 300 C.

  18. THE 300 km s{sup -1} STELLAR STREAM NEAR SEGUE 1: INSIGHTS FROM HIGH-RESOLUTION SPECTROSCOPY OF ITS BRIGHTEST STAR

    SciTech Connect (OSTI)

    Frebel, Anna; Casey, Andrew R.; Lunnan, Ragnhild; Norris, John E.; Wyse, Rosemary F. G.; Gilmore, Gerard

    2013-07-01

    We present a chemical abundance analysis of 300S-1, the brightest likely member star of the 300 km s{sup -1} stream near the faint satellite galaxy Segue 1. From a high-resolution Magellan/MIKE spectrum, we determine a metallicity of [Fe/H] = -1.46 {+-} 0.05 {+-} 0.23 (random and systematic uncertainties) for star 300S-1, and find an abundance pattern similar to typical halo stars at this metallicity. Comparing our stellar parameters to theoretical isochrones, we estimate a distance of 18 {+-} 7 kpc. Both the metallicity and distance estimates are in good agreement with what can be inferred from comparing the Sloan Digital Sky Survey photometric data of the stream stars to globular cluster sequences. While several other structures overlap with the stream in this part of the sky, the combination of kinematic, chemical, and distance information makes it unlikely that these stars are associated with either the Segue 1 galaxy, the Sagittarius Stream, or the Orphan Stream. Streams with halo-like abundance signatures, such as the 300 km s{sup -1} stream, present another observational piece for understanding the accretion history of the Galactic halo.

  19. 1,153-ton Waste Vault Removed from 300 Area- Vault held waste tanks with contamination from Hanford’s former laboratory facilities

    Broader source: Energy.gov [DOE]

    Today, the Department of Energy’s (DOE’s) Richland Operations Office announced the removal of a massive concrete vault that once held two 15,000-gallon stainless steel tanks used to collect highly contaminated waste from Hanford’s 300 Area laboratories as part of the River Corridor Closure project.

  20. Generation and use of high power 213 nm and 266 nm laser radiation and tunable 210-400 nm laser radiation with BBO crystal matrix array

    DOE Patents [OSTI]

    Gruen, Dieter M.

    2000-01-01

    A 213 nm laser beam is capable of single photon ablative photodecomposition for the removal of a polymer or biological material substrate. Breaking the molecular bonds and displacing the molecules away from the substrate in a very short time period results in most of the laser photon energy being carried away by the displaced molecules, thus minimizing thermal damage to the substrate. The incident laser beam may be unfocussed and is preferably produced by quintupling the 1064 nm radiation from a Nd:YAG solid state laser, i.e., at 213 nm. In one application, the 213 nm laser beam is expanded in cross section and directed through a plurality of small beta barium borate (BBO) crystals for increasing the energy per photon of the laser radiation directed onto the substrate. The BBO crystals are arranged in a crystal matrix array to provide a large laser beam transmission area capable of accommodating high energy laser radiation without damaging the BBO crystals. The BBO crystal matrix array may also be used with 266 nm laser radiation for carrying out single or multi photon ablative photodecomposition. The BBO crystal matrix array may also be used in an optical parametric oscillator mode to generate high power tunable laser radiation in the range of 210-400 nm.

  1. Adiabatic release measurements in aluminum between 400 and 1200 GPa: Characterization of aluminum as a shock standard in the multimegabar regime

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Knudson, Marcus D.; Desjarlais, Michael P.; Pribram-Jones, Aurora

    2015-06-15

    Aluminum has been used prolifically as an impedance matching standard in the multimegabar regime (1 Mbar = 100 GPa), particularly in nuclear driven, early laser driven, and early magnetically driven flyer plate experiments. The accuracy of these impedance matching measurements depends upon the knowledge of both the Hugoniot and release or reshock response of aluminum. Here, we present the results of several adiabatic release measurements of aluminum from ~400–1200 GPa states along the principal Hugoniot using full density polymethylpentene (commonly known as TPX), and both ~190 and ~110 mg/cc silica aerogel standards. Additionally, these data were analyzed within the frameworkmore » of a simple, analytical model that was motivated by a first-principles molecular dynamics investigation into the release response of aluminum, as well as by a survey of the release response determined from several tabular equations of state for aluminum. Combined, this theoretical and experimental study provides a method to perform impedance matching calculations without the need to appeal to any tabular equation of state for aluminum. Furthermore, as an analytical model, this method allows for propagation of all uncertainty, including the random measurement uncertainties and the systematic uncertainties of the Hugoniot and release response of aluminum. This work establishes aluminum for use as a high-precision standard for impedance matching in the multimegabar regime.« less

  2. Adiabatic release measurements in aluminum between 400 and 1200 GPa: Characterization of aluminum as a shock standard in the multimegabar regime

    SciTech Connect (OSTI)

    Knudson, Marcus D.; Desjarlais, Michael P.; Pribram-Jones, Aurora

    2015-06-15

    Aluminum has been used prolifically as an impedance matching standard in the multimegabar regime (1 Mbar = 100 GPa), particularly in nuclear driven, early laser driven, and early magnetically driven flyer plate experiments. The accuracy of these impedance matching measurements depends upon the knowledge of both the Hugoniot and release or reshock response of aluminum. Here, we present the results of several adiabatic release measurements of aluminum from ~400–1200 GPa states along the principal Hugoniot using full density polymethylpentene (commonly known as TPX), and both ~190 and ~110 mg/cc silica aerogel standards. Additionally, these data were analyzed within the framework of a simple, analytical model that was motivated by a first-principles molecular dynamics investigation into the release response of aluminum, as well as by a survey of the release response determined from several tabular equations of state for aluminum. Combined, this theoretical and experimental study provides a method to perform impedance matching calculations without the need to appeal to any tabular equation of state for aluminum. Furthermore, as an analytical model, this method allows for propagation of all uncertainty, including the random measurement uncertainties and the systematic uncertainties of the Hugoniot and release response of aluminum. This work establishes aluminum for use as a high-precision standard for impedance matching in the multimegabar regime.

  3. Adiabatic release measurements in aluminum between 400-1200 GPa. Characterization of aluminum as a shock standard in the multimegabar regime

    SciTech Connect (OSTI)

    Knudson, Marcus D.; Desjarlais, Michael P.; Pribram-Jones, Aurora

    2015-06-15

    Aluminum has been used prolifically as an impedance matching standard in the multimegabar regime (1 Mbar = 100 GPa), particularly in nuclear driven, early laser driven, and early magnetically driven flyer plate experiments. The accuracy of these impedance matching measurements depends upon the knowledge of both the Hugoniot and release or reshock response of aluminum. Here, we present the results of several adiabatic release measurements of aluminum from ~4001200 GPa states along the principal Hugoniot using full density polymethylpentene (commonly known as TPX), and both ~190 and ~110 mg/cc silica aerogel standards. Additionally, these data were analyzed within the framework of a simple, analytical model that was motivated by a first-principles molecular dynamics investigation into the release response of aluminum, as well as by a survey of the release response determined from several tabular equations of state for aluminum. Combined, this theoretical and experimental study provides a method to perform impedance matching calculations without the need to appeal to any tabular equation of state for aluminum. Furthermore, as an analytical model, this method allows for propagation of all uncertainty, including the random measurement uncertainties and the systematic uncertainties of the Hugoniot and release response of aluminum. This work establishes aluminum for use as a high-precision standard for impedance matching in the multimegabar regime.

  4. Design and Construction of a 500 KW CW, 400 MHZ Klystron To Be Used As RF Power Source For LHC/RF Component Tests

    SciTech Connect (OSTI)

    Pearson, Chris

    2003-05-05

    A 500 kW cw klystron operating at 400 MHz was developed and constructed jointly by CERN and SLAC for use as a high-power source at CERN for testing LHC/RF components such as circulators, RF absorbers and superconducting cavities with their input couplers. The design is a modification of the 353 MHz SLAC PEP-I klystron. More than 80% of the original PEP-I tube parts could thus be incorporated in the LHC test klystron which resulted in lower engineering costs as well as reduced development and construction time. The physical length between cathode plane and upper pole plate was kept unchanged so that a PEP-I tube focusing solenoid, available at CERN, could be re-used. With the aid of the klystron simulation codes JPNDISK and CONDOR, the design of the LHC tube was accomplished, which resulted in a tube with noticeably higher efficiency than its predecessor, the PEP-I klystron. The integrated cavities were redesigned using SUPERFISH and the output coupling circuit, which also required redesigning, was done with the aid of MAFIA. Details of the tube development and test results are presented.

  5. RELAP5/MOD3.2 Assessment Using CHF Data from the KS-1 and V-200 Experiment Facilities

    SciTech Connect (OSTI)

    Bayless, Paul David

    2001-07-01

    The RELAP/MOD3.2 computer code has been assessed using rod bundle critical heat flux data from the KS-1 and V-200 facilities. This work was performed as part of the U.S. Department of Energy’s International Nuclear Safety Program, and is part of the effort addressing the capability of the RELAP5/MOD3.2 code to model transients in Soviet-designed reactors. Designated VVER Standard Problem 7, these tests addressed one of the important phenomena related to VVER behavior that the code needs to simulate well, core heat transfer. The code was judged to be in minimal agreement with the experiment data, consistently overpredicting the measured critical heat flux. It is recommended that a model development effort be undertaken to develop a critical heat flux model for RELAP5 that better represents the behavior in VVER rod bundles.

  6. Observation of D0 meson nuclear modifications in Au+Au collisions at sNN=200 GeV

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Adamczyk, L.; Adkins, J. K.; Agakishiev, G.; Aggarwal, M. M.; Ahammed, Z.; Alekseev, I.; Alford, J.; Anson, C. D.; Aparin, A.; Arkhipkin, D.; et al

    2014-09-30

    We report the first measurement of charmed-hadron (D0) production via the hadronic decay channel (D0→K-+π+) in Au+Au collisions at √sNN=200 GeV with the STAR experiment. The charm production cross section per nucleon-nucleon collision at midrapidity scales with the number of binary collisions, Nbin, from p+p to central Au+Au collisions. The D0 meson yields in central Au+Aucollisions are strongly suppressed compared to those in p+p scaled by Nbin, for transverse momenta pT>3 GeV/c, demonstrating significant energy loss of charm quarks in the hot and dense medium. An enhancement at intermediate pT is also observed. Model calculations including strong charm-medium interactions andmore »coalescence hadronization describe our measurements.« less

  7. Measurements of Transverse Energy Distributions in Au+Au Collisions at {radical}s{sub NN} = 200 GeV

    SciTech Connect (OSTI)

    Adams, J.; Aggarwal, M.M.; Ahammed, Z.; Amonett, J.; Anderson, B.D.; Arkhipkin, D.; Averichev, G.S.; Bai, Y.; Balewski, J.; Barannikova, O.; Barnby, L.S.; Baudot, J.; Bekele, S.; Belaga, V.V.; Bellwied, R.; Berger, J.; Bezverkhny, B.I.; Bharadwaj, S.; Bhatia, V.S.; Bichsel, H.; Billmeier, A.; Bland, L.C.; Blyth, C.O.; Bonner, B.E.; Boucham, A.; Botje, M.; Brandin, A.; Bravar, A.; Bystersky, M.; Cadman, R.V.; Cai, X.Z.; Caines, H.; Calderon de la Barca Sanchez, M.; Carroll, J.; Castillo, J.; Cebra, D.; Chajecki, Z.; Chaloupka, P.; Chattopdhyay, S.; Chen, H.F.; Chen, Y.; Cheng, J.; Cherney, M.; Chikanian, A.; Christie, W.; Coffin, J.P.; Cormier, T.M.; Cramer, J.G.; Crawford, H.J.; Das, D.; Das, S.; de Moura, M.M.; Derevschikov, A.A.; Didenko, L.; Dietel, T.; Dong, W.J.; Dong, X.; Draper, J.E.; Du, F.; Dubey, A.K.; Dunin, V.B.; Dunlop, J.C.; Dutta Mazumdar, M.R>; Eckardt, V.; Edwards, W.R.; Efimov, L.G.; Emelianov, V.; Engelage, J.; Eppley, G.; Erazmus, B.; Estienne, M.; Fachini, P.; Faivre, J.; Fatemi, R.; Filimonov, K.; Finch, E.; Fine, V.; Fisyak, Y.; Foley, K.J.; Fomenko, K.; Fu, J.; Gagliardi, C.A.; Gans, J.; Ganti, M.S.; Gaudichet, L.; Geurts, F.; Ghazikhanian, V.; Ghosh, P.; Gonzalez, J.E.; Grachov, O.; Grebenyuk, O.; Grosnick, D.; Guertin, S.M.; Guo, Y.; Gupta, A.; Gutierrez, T.D.; Hallman, T.J.; Hamed, A.; Hardtke, D.; Harris, J.W.; Heinz, M.; Henry, T.W.; Hepplemann, S.; Hippolyte, B.; Hirsch, A.; Hjort, E.; Hoffmann, G.W.; Huang, H.Z.; Huang, S.L.; Hughes, E.W.; Humanic, T.J.; Igo, G.; Ishihara, A.; Jacobs, P.; Jacobs, W.W.; Janik, M.; Jiang, H.; Jones, P.G.; Judd, E.G.; Kabana, S.; Kang, K.; Kaplan, M.; Keane, D.; Khodyrev, V.Yu.; Kiryluk, J.; Kisiel, A.; Kislov, E.M.; Klay, J.; Klein, S.R.; Klyachko, A.; Koetke, D.D.; Kollegger, T.; Kopytine, M.; Kotchenda, L.; Kramer, M.; Kravtsov, P.; Kravtsov, V.I.; Krueger, K.; Kuhn, C.; Kulikov, A.I.; Kumar, A.; Kunz, C.L.; Kutuev, R.Kh.; Kuznetsov, A.A.; Lamont, M.A.C.; et al.

    2004-07-02

    Transverse energy (E{sub T}) distributions have been measured for Au+Au collisions at {radical}s{sub NN} = 200 GeV by the STAR collaboration at RHIC. E{sub T} is constructed from its hadronic and electromagnetic components, which have been measured separately. E{sub T} production for the most central collisions is well described by several theoretical models whose common feature is large energy density achieved early in the fireball evolution. The magnitude and centrality dependence of E{sub T} per charged particle agrees well with measurements at lower collision energy, indicating that the growth in E{sub T} for larger collision energy results from the growth in particle production. The electromagnetic fraction of the total E{sub T} is consistent with a final state dominated by mesons and independent of centrality.

  8. Dielectron Azimuthal Anisotropy at mid-rapidity in Au+Au collisions at root s=200GeV

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Adamczyk, L.

    2014-12-11

    We report on the first measurement of the azimuthal anisotropy (v₂) of dielectrons (e⁺e⁻ pairs) at mid-rapidity from √(sNN)=200 GeV Au + Au collisions with the STAR detector at the Relativistic Heavy Ion Collider (RHIC), presented as a function of transverse momentum (pT) for different invariant-mass regions. In the mass region Mee<1.1 GeV/c² the dielectron v₂ measurements are found to be consistent with expectations from π⁰,η,ω, and Φ decay contributions. In the mass region 1.1ee<2.9GeV/c², the measured dielectron v₂ is consistent, within experimental uncertainties, with that from the cc¯ contributions.

  9. Forward Neutral Pion Transverse Single Spin Asymmetries in p+p Collisions at sqrt s = 200 GeV

    SciTech Connect (OSTI)

    STAR Coll

    2008-11-26

    We report precision measurements of the Feynman-x (x{sub F}) dependence, and first measurements of the transverse momentum (p{sub T}) dependence, of transverse single spin asymmetries for the production of {pi}{sup 0} mesons from polarized proton collisions at {radical}s = 200 GeV. The x{sub F} dependence of the results are in fair agreement with perturbative QCD (pQCD) model calculations that identify orbital motion of quarks and gluons within the proton as the origin of the spin effects. Results for the p{sub T} dependence at fixed x{sub F} are not consistent with these same pQCD-based calculations.

  10. Dielectron Azimuthal Anisotropy at mid-rapidity in Au+Au collisions at root s=200GeV

    SciTech Connect (OSTI)

    Adamczyk, L.

    2014-12-11

    We report on the first measurement of the azimuthal anisotropy (v₂) of dielectrons (e⁺e⁻ pairs) at mid-rapidity from √(sNN)=200 GeV Au + Au collisions with the STAR detector at the Relativistic Heavy Ion Collider (RHIC), presented as a function of transverse momentum (pT) for different invariant-mass regions. In the mass region Mee<1.1 GeV/c² the dielectron v₂ measurements are found to be consistent with expectations from π⁰,η,ω, and Φ decay contributions. In the mass region 1.1ee<2.9GeV/c², the measured dielectron v₂ is consistent, within experimental uncertainties, with that from the cc¯ contributions.

  11. Applications of nuclear reaction analysis to metal hydride film characterization at the GEND 200 KeV accelerator facility

    SciTech Connect (OSTI)

    Malbrough, D.J.; Becker, R.H.

    1985-01-01

    Nuclear reaction analysis (NRA) is a quantitative analytical technique that usually involves the use of MeV ion beams and resonant nuclear reactions to non-destructively probe materials for elemental content and depth profiles. Low energy, non-resonant nuclear reactions can also be exploited for NRA and procedures have been developed for using the GEND 200-KeV accelerator to characterize neutron generator components by that technique. The procedures involve the detection and analysis of fusion reaction products generated by the interactions of deuteron beams with light elements in metal hydride films. A description of the accelerator system is presented along with some of the unique NRA procedures that have recently been developed for its use. The system is used to measure neutron output efficiencies of metal deuterides and tritides by the associated particle technique (APT) and accurate neutron yield measurements have been made for a number of materials for which data was formerly not available.

  12. Dielectron Azimuthal Anisotropy at mid-rapidity in Au+Au collisions at root s=200GeV

    SciTech Connect (OSTI)

    Adamczyk, L.; STAR Collaboration

    2014-12-01

    We report on the first measurement of the azimuthal anisotropy (v?) of dielectrons (e?e? pairs) at mid-rapidity from ?(sNN)=200 GeV Au + Au collisions with the STAR detector at the Relativistic Heavy Ion Collider (RHIC), presented as a function of transverse momentum (pT) for different invariant-mass regions. In the mass region Mee<1.1 GeV/c the dielectron v? measurements are found to be consistent with expectations from ??,?,?, and ? decay contributions. In the mass region 1.1ee<2.9GeV/c, the measured dielectron v? is consistent, within experimental uncertainties, with that from the cc contributions.

  13. Nuclear matter effects on J/? production in asymmetric Cu+Au collisions at ?SNN=200 GeV

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Adare, A.

    2014-12-18

    We report on J/? production from asymmetric Cu+Au heavy-ion collisions at ?sNN =200 GeV at the Relativistic Heavy Ion Collider at both forward (Cu-going direction) and backward (Au-going direction) rapidities. The nuclear modification of J/? yields in Cu+Au collisions in the Au-going direction is found to be comparable to that in Au+Au collisions when plotted as a function of the number of participating nucleons. In the Cu-going direction, J/? production shows a stronger suppression. This difference is comparable in magnitude and has the same sign as the difference expected from shadowing effects due to stronger low-x gluon suppression in themorelarger Au nucleus. The relative suppression is opposite to that expected from hot nuclear matter dissociation, since a higher energy density is expected in the Au-going direction.less

  14. Manganese-Based Magnets: Manganese-Based Permanent Magnet with 40 MGOe at 200°C

    SciTech Connect (OSTI)

    2012-01-01

    REACT Project: PNNL is working to reduce the cost of wind turbines and EVs by developing a manganese-based nano-composite magnet that could serve as an inexpensive alternative to rare-earth-based magnets. The manganese composite, made from low-cost and abundant materials, could exceed the performance of today’s most powerful commercial magnets at temperature higher than 200°C. Members of PNNL’s research team will leverage comprehensive computer high-performance supercomputer modeling and materials testing to meet this objective. Manganese-based magnets could withstand higher temperatures than their rare earth predecessors and potentially reduce the need for any expensive, bulky engine cooling systems for the motor and generator. This would further contribute to cost savings for both EVs and wind turbines.

  15. Observation of D0 meson nuclear modifications in Au+Au collisions at sNN=200 GeV

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Adamczyk, L.; Adkins, J. K.; Agakishiev, G.; Aggarwal, M. M.; Ahammed, Z.; Alekseev, I.; Alford, J.; Anson, C. D.; Aparin, A.; Arkhipkin, D.; et al

    2014-09-30

    We report the first measurement of charmed-hadron (D0) production via the hadronic decay channel (D0→K-+π+) in Au+Au collisions at √sNN=200 GeV with the STAR experiment. The charm production cross section per nucleon-nucleon collision at midrapidity scales with the number of binary collisions, Nbin, from p+p to central Au+Au collisions. The D0 meson yields in central Au+Aucollisions are strongly suppressed compared to those in p+p scaled by Nbin, for transverse momenta pT>3 GeV/c, demonstrating significant energy loss of charm quarks in the hot and dense medium. An enhancement at intermediate pT is also observed. Model calculations including strong charm-medium interactions andmore » coalescence hadronization describe our measurements.« less

  16. Identified particle distributions in pp and Au+Au collisions atsqrt sNN=200 GeV

    SciTech Connect (OSTI)

    Adams, J.; Adler, C.; Aggarwal, M.M.; Ahammed, Z.; Amonett, J.; Anderson, B.D.; Anderson, M; Arkhipkin, D.; Averichev, G.S.; Badyal,S.K.; Balewski, J.; Barannikova, O.; Barnby, L.S.; Baudot, J.; Bekele,S.; Belaga, V.V.; Bellwied, R.; Berger, J.; Bezverkhny, B.I.; Bhardwaj,S.; Bhaskar, P.; Bhati, A.K.; Bichsel, H.; Billmeier, A.; Bland, L.C.; Blyth, C.O.; Bonner, B.E.; Botje, M.; Boucham, A.; Brandin, A.; Bravar,A.; Cadman, R.V.; Cai, X.Z.; Caines, H.; Calderon de la Barca Sanchez,M.; Carroll, J.; Castillo, J.; Castro, M.; Cebra, D.; Chaloupka, P.; Chattopadhyay, S.; Chen, H.F.; Chen, Y.; Chernenko, S.P.; Cherney, M.; Chikanian, A.; Choi, B.; Christie, W.; Coffin, J.P.; Cormier, T.M.; Cramer, J.G.; Crawford, H.J.; Das, D.; Das, S.; Derevschikov, A.A.; Didenko, L.; Dietel, T.; Dong, X.; Draper, J.E.; Du, F.; Dubey, A.K.; Dunin, V.B.; Dunlop, J.C.; Dutta Majumdar, M.R.; Eckardt, V.; Efimov,L.G.; Emelianov, V.; Engelage, J.; Eppley, G.; Erazmus, B.; Estienne, M.; Fachini, P.; Faine, V.; Faivre, J.; Fatemi, R.; Filimonov, K.; Filip, P.; Finch, E.; Fisyak, Y.; Flierl, D.; Foley, K.J.; Fu, J.; Gagliardi, C.A.; Ganti, M.S.; Gutierrez, T.D.; Gagunashvili, N.; Gans, J.; Gaudichet, L.; Germain, M.; Geurts, F.; Ghazikhanian, V.; Ghosh, P.; Gonzalez, J.E.; Grachov, O.; Grigoriev, V.; Cronstal, S.; Grosnick, D.; Guedon, M.; Guertin, S.M.; Gupta, A.; Gushin, E.; Hallman, T.J.; Hardtke, D.; Harris,J.W.; Heinz, M.; Henry, T.W.; Heppelmann, S.; Herston, T.; Hippolyte, B.; Hirsch, A.; Hjort, E.; Hoffmann, G.W.; Horsley, M.; Huang, H.Z.; Huang,S.L.; Humanic, T.J.; Igo, G.; Ishihara, A.; Jacobs, P.; Jacobs, W.W.; Janik, M.; Johnson, I.; Jones, P.G.; Judd, E.G.; Kabana, S.; Kaneta, M.; Kaplan, M.; Keane, D.; Kiryluk, J.; Kisiel, A.; Klay, J.; Klein, S.R.; Klyachko, A.; Koetke, D.D.; Kollegger, T.; Konstantinov, A.S.; Kopytine,S.M.; Kotchenda, L.; Kovalenko, A.D.; Kramer, M.; Kravtsov, P.; Krueger,K.; Kuhn, C.; Kulikov, A.I.; Kumar, A.; et al.

    2003-10-06

    Transverse mass and rapidity distributions for charged pions, charged kaons, protons and antiprotons are reported for {radical}sNN = 200 GeV pp and Au+Au collisions at RHIC. The transverse mass distributions are rapidity independent within |y| < 0.5, consistent with a boost-invariant system in this rapidity interval. Spectral shapes and relative particle yields are similar in pp and peripheral Au+Au collisions and change smoothly to central Au+Au collisions. No centrality dependence was observed in the kaon and antiproton production rates relative to the pion production rate from medium-central to central collisions. Chemical and kinetic equilibrium model fits to our data reveal strong radial flow and relatively long duration from chemical to kinetic freeze-out in central Au+Au collisions. The chemical freeze-out temperature appears to be independent of initial conditions at RHIC energies.

  17. Compact focusing spectrometer: Visible (1 eV) to hard x-rays (200 keV)

    SciTech Connect (OSTI)

    Baronova, E. O.; Stepanenko, A. M.; Pereira, N. R.

    2014-11-15

    A low-cost spectrometer that covers a wide range of photon energies can be useful to teach spectroscopy, and for simple, rapid measurements of the photon spectrum produced by small plasma devices. The spectrometer here achieves its wide range, nominally from 1 eV to 200 keV, with a series of spherically and cylindrically bent gratings or crystals that all have the same shape and the same radius of curvature; they are complemented by matching apertures and diagnostics on the Rowland circle that serves as the circular part of the spectrometer's vacuum vessel. Spectral lines are easily identified with software that finds their positions from the dispersion of each diffractive element and the known energies of the lines.

  18. 200 kHz Commercial Sonar Systems Generate Lower Frequency Side Lobes Audible to Some Marine Mammals

    SciTech Connect (OSTI)

    Deng, Zhiqun; Southall, Brandon; Carlson, Thomas J.; Xu, Jinshan; Martinez, Jayson J.; Weiland, Mark A.; Ingraham, John M.

    2014-04-15

    The spectral properties of pulses transmitted by three commercially available 200 kHz echo sounders were measured to assess the possibility that sound energy in below the center (carrier) frequency might be heard by marine mammals. The study found that all three sounders generated sound at frequencies below the center frequency and within the hearing range of some marine mammals and that this sound was likely detectable by the animals over limited ranges. However, at standard operating source levels for the sounders, the sound below the center frequency was well below potentially harmful levels. It was concluded that the sounds generated by the sounders could affect the behavior of marine mammals within fairly close proximity to the sources and that that the blanket exclusion of echo sounders from environmental impact analysis based solely on the center frequency output in relation to the range of marine mammal hearing should be reconsidered.

  19. Revision of Army regulation (AR) 200-2, environmental effects of Army actions, and the application of total quality mangement (TQM) principles

    SciTech Connect (OSTI)

    Merkel, H,K.; Robitaille, P.

    1995-12-01

    AR 200-2 is the Army`s implementing regulation to the National Environmental Policy Act (NEPA) and DoD`s NEPA Directive DoDD 6050.1. AR 200-2 was last revised in the late 1980s and since then the scope of Army NEPA compliance activities have significantly increased, and NEPA practice and case law are continually changing. The purpose of revising AR 200-2 is to provide Army personel with clear and Concise guidance on how to meet their NEPA compliance requirements. The revision process included reviewing the current AR 200-2 to identify areas and topics needing clarification or modification; conferring with Army NEPA personnel to obtain views on NEPA compliance practices and procedures; conducting a review and analysis of significant, recent developments in NEPA case law; reviewing other federal NEPA implementing regulations to identify useful, transferrable concepts; preparing a {open_quotes}strawman{close_quotes} version of AR 200-2 to use as a starting point in the revision process; coordinating and consolidating input from the AR 200-2 Revisions Steering Committee; and responding to review comments. A draft version of AR 200-2 has been completed and informal Army-wide comments have been addressed. Some of the issues that the AR 200-2 Revisions Steering Committee considered during the revision effort included expanding the list of categorical exclusions, determining the appropriate length for the public comment period for environmental assessments prior to approval of the finding of no significant impact, determining the appropriate level of analysis for Army actions abroad, and determining whether Comprehensive Environmental Response Compensation Liability Act (CERCLA) or Resource Conservation and Recovery Act (RCRA) actions should be addressed under NEPA. Total Quality Management (TQM) principles were applied during the revision process. GroupSystems{trademark} software was used as a vehicle to enhance total group participation from managers to practitioners.

  20. HABAdv_200.pdf

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

  1. ARM - Datastreams - aosccn200

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    ... second column count CCNoverflow2 ( time ) CCN Proportional valve voltage, first column V CCNproportionalvalvevoltage1 ( time ) CCN Proportional valve voltage, second column ...

  2. TECHNICAL EVALUATION OF SOIL REMEDIATION ALTERNATIVES AT THE BUILDING 812 OPERABLE UNIT, LAWRENCE LIVERMORE NATIONAL LABORATORY SITE 300

    SciTech Connect (OSTI)

    Eddy-Dilek, C.; Miles, D.; Abitz, R.

    2009-08-14

    The Department of Energy Livermore Site Office requested a technical review of remedial alternatives proposed for the Building 812 Operable Unit, Site 300 at the Lawrence Livermore National Laboratory. The team visited the site and reviewed the alternatives proposed for soil remediation in the draft RI/FS and made the following observations and recommendations. Based on the current information available for the site, the team did not identify a single technology that would be cost effective and/or ecologically sound to remediate DU contamination at Building 812 to current remedial goals. Soil washing is not a viable alternative and should not be considered at the site unless final remediation levels can be negotiated to significantly higher levels. This recommendation is based on the results of soil washing treatability studies at Fernald and Ashtabula that suggest that the technology would only be effective to address final remediation levels higher than 50 pCi/g. The technical review team identified four areas of technical uncertainty that should be resolved before the final selection of a preferred remedial strategy is made. Areas of significant technical uncertainty that should be addressed include: (1) Better delineation of the spatial distribution of surface contamination and the vertical distribution of subsurface contamination in the area of the firing table and associated alluvial deposits; (2) Chemical and physical characterization of residual depleted uranium (DU) at the site; (3) Determination of actual contaminant concentrations in air particulates to support risk modeling; and (4) More realistic estimation of cost for remedial alternatives, including soil washing, that were derived primarily from vendor estimates. Instead of conducting the planned soil washing treatability study, the team recommends that the site consider a new phased approach that combines additional characterization approaches and technologies to address the technical uncertainty in

  3. Measurement of transmission efficiency for 400 MeV proton beam through collimator at Fermilab MuCool Test Area using Chromox-6 scintillation screen

    SciTech Connect (OSTI)

    Jana, M. R.; Chung, M.; Leonova, M.; Moretti, A.; Palmer, M.; Schwarz, T.; Tollestrup, A.; Yonehara, K.; Freemire, B.; Hanlet, P.; Torun, Y.

    2013-06-15

    The MuCool Test Area (MTA) at Fermilab is a facility to develop the technology required for ionization cooling for a future Muon Collider and/or Neutrino Factory. As part of this research program, feasibility studies of various types of RF cavities in a high magnetic field environment are in progress. As a unique approach, we have tested a RF cavity filled with a high pressure hydrogen gas with a 400 MeV proton beam in an external magnetic field (B = 3 T). Quantitative information about the number of protons passing through this cavity is an essential requirement of the beam test. The MTA is a flammable gas (hydrogen) hazard zone. Due to safety reasons, no active (energized) beam diagnostic instrument can be used. Moreover, when the magnetic field is on, current transformers (toroids) used for beam intensity measurements do not work due to the saturation of the ferrite material of the transformer. Based on these requirements, we have developed a passive beam diagnostic instrumentation using a combination of a Chromox-6 scintillation screen and CCD camera. This paper describes details of the beam profile and position obtained from the CCD image with B = 0 T and B = 3 T, and for high and low intensity proton beams. A comparison is made with beam size obtained from multi-wires detector. Beam transmission efficiency through a collimator with a 4 mm diameter hole is measured by the toroids and CCD image of the scintillation screen. Results show that the transmission efficiency estimated from the CCD image is consistent with the toroid measurement, which enables us to monitor the beam transmission efficiency even in a high magnetic field environment.

  4. Irradiation creep and density changes observed in MA957 pressurized tubes irradiated to doses of 40-110 dpa at 400-750°C in FFTF

    SciTech Connect (OSTI)

    Toloczko, Mychailo B.; Garner, Frank A.; Maloy, Stuart A.

    2012-12-30

    An irradiation creep and swelling study was performed on tubing constructed from the Y2O3-strengthened ODS ferritic steel MA957. As a result of the reduction operations during manufacture, the grains in the tubing were highly elongated in the direction of the tubing axis, with an aspect ratio of ~10:1. Pressurized creep tubes were irradiated in the Fast Flux Test Facility (FFTF) to doses ranging from 40 dpa to 110 dpa at temperatures ranging from 400 to 750°C. The diametral strains produced during irradiation exhibit very strong transient strains that are linearly dependent on stress and increase with irradiation temperature before reaching temperature-independent steady-state creep rates of 0.6-0.7 X 10-6 (MPa dpa)-1. Contributions to transient strains may not arise only from classical thermal creep or irradiation creep considerations, but also may result from an irradiation-stimulated growth process whereby the highly elongated grain structure reduces the aspect ratio to produce fatter grains and thereby increases in the tube diameter. One manifestation of this process is a change in tube diameter that is not accompanied by a density change characteristic of void swelling or precipitation-induced changes in lattice parameter. These results provide the first conclusive demonstration that resistance to irradiation creep can be extended to higher temperatures by dispersoid addition, and most importantly, this resistance is maintained to high radiation damage levels. However, the irradiation creep compliance is not reduced by dispersoid addition, casting some doubt on various proposed climb and glide mechanisms of irradiation creep.

  5. Neutron-Induced Microstructural Evolution of Fe-15Cr-16Ni Alloys at ~400 C During Neutron Irradiation in the FFTF Fast Reactor

    SciTech Connect (OSTI)

    Okita, Taira; Sato, Toshihiko; Sekimura, Naoto; Garner, Francis A.; Greenwood, Lawrence R.; Wolfer, W. G.; Isobe, Yoshihiro

    2001-06-30

    An experiment conducted at ~400 degrees C on simple model austenitic alloys (Fe-15Cr-16Ni and Fe-15Cr-16Ni-0.25Ti, both with and without 500 appm boron) irradiated in the FFTF fast reactor at seven different dpa rates clearly shows that lowering of the atomic displacement rate leads to a pronounced reduction in the transient regime of void swelling. While the steady state swelling rate (~1%/dpa) of these alloys is unaffected by changes in the dpa rate, the transient regime of swelling can vary from <1 to ~60 dpa when the dpa rate varies over more than two orders of magnitude. This range of dpa rates covers the full span of fusion, PWR and fast reactor rates. The origin of the flux sensitivity of swelling arises first in the evolution of the Frank dislocation loop population, its unfaulting, and the subsequent evolution of the dislocation network. There also appears to be some flux sensitivity to the void nucleation process. Most interestingly, the addition of titanium suppresses the void nucleation process somewhat, but does not alter the duration of the transient regime of swelling or its sensitivity to dpa rate. Side-by-side irradiation of boron-modified model alloys in this same experiment shows that higher helium generation rates homogenize the swelling somewhat, but do not significantly change its magnitude or flux sensitivity. The results of this study support the prediction that austenitic alloys irradiated at PWR-relevant displacement rates will most likely swell more than when irradiated at higher rates characteristic of fast reactors. Thus, the use of swelling data accumulated in fast reactors may possibly lead to an under-prediction of swelling in lower-flux PWRs and fusion devices.

  6. Microsoft PowerPoint - arm2008_1.ppt

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    TEMPLATE DESIGN © 2007 www.PosterPresentations.com 20 25 30 35 40 45 Fractional day 0 100 200 300 400 OLR (W/m 2 ) SCAM_std SCAM_ice OBS 20 25 30 35 40 45 Fractional day 380 400 420 440 460 surface LW DN flux(W/m 2 ) OBS SCAM_ice SCAM_std 0 5 10 15 20 Height (km) 0.1 1.0 3.0 4.0 6.0 8.0 14.0 20.0 30.0 40.0 60.0 (10 -3 g/m 3 ) SCAM_std 0 5 10 15 20 Height (km) SCAM_ice 0 5 10 15 20 Height (km) Radar 20 25 30 35 40 45 Fractional day 0 5 10 15 20 Height (km) Satellite Evaluating cloud

  7. Evaluation of Using Caged Clams to Monitor Contaminated Groundwater Exposure in the Near-Shore Environment of the Hanford Site 300 Area

    SciTech Connect (OSTI)

    Larson, Kyle B.; Poston, Ted M.; Tiller, Brett L.

    2008-01-31

    The Asiatic clam (Corbicula fluminea) has been identified as an indicator species for locating and monitoring contaminated groundwater in the Columbia River. Pacific Northwest National Laboratory conducted a field study to explore the use of caged Asiatic clams to monitor contaminated groundwater upwelling in the 300 Area near-shore environment and assess seasonal differences in uranium uptake in relation to seasonal flow regimes of the Columbia River. Additional objectives included examining the potential effects of uranium accumulation on growth, survival, and tissue condition of the clams. This report documents the field conditions and procedures, laboratory procedures, and statistical analyses used in collecting samples and processing the data. Detailed results are presented and illustrated, followed by a discussion comparing uranium concentrations in Asiatic clams collected at the 300 Area and describing the relationship between river discharge, groundwater indicators, and uranium in clams. Growth and survival, histology, and other sources of environmental variation also are discussed.

  8. PowerPoint Presentation

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    the SWS direct irradiance contamination on the analysis of transition zone between cloudy and cloud-free regions Alexander Marshak (GSFC) and Christine Chiu (UMBC) Cloud-free zenith radiance will be uncontaminated as long as the SWS is not illuminated by directly transmitted solar irradiance Main Assumption SZA=45 o May 18, 2007 0 100 200 300 400 0 125 250 375 time (sec) wvl (nm) 400 800 1200 1600 2000 (nm) wavelength (nm) 0.00 0.20 0.40 0.60 0.80 20070518 Blocked around 400 sec Unblocked from 0

  9. System-Scale Model of Aquifer, Vadose Zone, and River Interactions for the Hanford 300 Area - Application to Uranium Reactive Transport

    SciTech Connect (OSTI)

    Rockhold, Mark L.; Bacon, Diana H.; Freedman, Vicky L.; Parker, Kyle R.; Waichler, Scott R.; Williams, Mark D.

    2013-10-01

    This report represents a synthesis and integration of basic and applied research into a system-scale model of the Hanford 300 Area groundwater uranium plume, supported by the U.S. Department of Energy’s Richland Operations (DOE-RL) office. The report integrates research findings and data from DOE Office of Science (DOE-SC), Office of Environmental Management (DOE-EM), and DOE-RL projects, and from the site remediation and closure contractor, Washington Closure Hanford, LLC (WCH). The three-dimensional, system-scale model addresses water flow and reactive transport of uranium for the coupled vadose zone, unconfined aquifer, and Columbia River shoreline of the Hanford 300 Area. The system-scale model of the 300 Area was developed to be a decision-support tool to evaluate processes of the total system affecting the groundwater uranium plume. The model can also be used to address “what if” questions regarding different remediation endpoints, and to assist in design and evaluation of field remediation efforts. For example, the proposed cleanup plan for the Hanford 300 Area includes removal, treatment, and disposal of contaminated sediments from known waste sites, enhanced attenuation of uranium hot spots in the vadose and periodically rewetted zone, and continued monitoring of groundwater with institutional controls. Illustrative simulations of polyphosphate infiltration were performed to demonstrate the ability of the system-scale model to address these types of questions. The use of this model in conjunction with continued field monitoring is expected to provide a rigorous basis for developing operational strategies for field remediation and for defining defensible remediation endpoints.

  10. Human Health and Ecological Risk Assessment for the Operation of the Explosives Waste Treatment Facility at Site 300 of the Lawrence Livermore National Laboratory

    SciTech Connect (OSTI)

    Gallegos, G; Daniels, J; Wegrecki, A

    2007-10-01

    This document contains the human health and ecological risk assessment for the Resource Recovery and Conservation Act (RCRA) permit renewal for the Explosives Waste Treatment Facility (EWTF). Volume 1 is the text of the risk assessment, and Volume 2 (provided on a compact disc) is the supporting modeling data. The EWTF is operated by the Lawrence Livermore National Laboratory (LLNL) at Site 300, which is located in the foothills between the cities of Livermore and Tracy, approximately 17 miles east of Livermore and 8 miles southwest of Tracy. Figure 1 is a map of the San Francisco Bay Area, showing the location of Site 300 and other points of reference. One of the principal activities of Site 300 is to test what are known as 'high explosives' for nuclear weapons. These are the highly energetic materials that provide the force to drive fissionable material to criticality. LLNL scientists develop and test the explosives and the integrated non-nuclear components in support of the United States nuclear stockpile stewardship program as well as in support of conventional weapons and the aircraft, mining, oil exploration, and construction industries. Many Site 300 facilities are used in support of high explosives research. Some facilities are used in the chemical formulation of explosives; others are locations where explosive charges are mechanically pressed; others are locations where the materials are inspected radiographically for such defects as cracks and voids. Finally, some facilities are locations where the machined charges are assembled before they are sent to the onsite test firing facilities, and additional facilities are locations where materials are stored. Wastes generated from high-explosives research are treated by open burning (OB) and open detonation (OD). OB and OD treatments are necessary because they are the safest methods for treating explosives wastes generated at these facilities, and they eliminate the requirement for further handling and

  11. Case Study of Anomalies Encountered During Remediation of Mixed Low-Level Waste Burial Grounds in the 100 and 300 Areas of the Hanford Site

    SciTech Connect (OSTI)

    Haass, M.J.; Zacharias, P.E.; Zacharias, A.E.

    2007-07-01

    Under the U.S. Department of Energy's River Corridor Closure Project, Washington Closure Hanford has completed remediation of more than 10 mixed low-level waste burial grounds in the 100 and 300 Areas of the Hanford Site. The records of decision for the burial grounds required excavation, characterization, and transport of contaminated material to a Resource Conservation and Recovery Act of 1976-compliant hazardous waste landfill. This paper discusses a sample of the anomalous waste found during remediation and provides an overview of the waste excavation activities. The 100 Area burial grounds received plutonium production reactor waste and waste associated with various test programs. Examples of 100 Area anomalies include spent nuclear fuel, elemental mercury, reactor hardware, and the remains of animals used in testing the effects of radionuclides on living organisms. The 300 Area burial grounds received waste from research and development laboratories and fuel manufacturing operations. Of the seven 300 Area burial grounds remediated to date, the most challenging has been the 618-2 Burial Ground. It presented significant challenges because of the potential for airborne alpha contamination and the discovery of plutonium in an isotopically pure form. Anomalies encountered in the 618-2 Burial Ground included a combination safe that contained gram quantities of plutonium, miscellaneous containers of unknown liquids, and numerous types of shielded shipping casks. Information presented in this paper will be an aid to those involved in remediation activities throughout the U.S. Department of Energy complex and at other nuclear waste disposal sites. (authors)

  12. Edge electroluminescence of the effective silicon point-junction light-emitting diode in the temperature range 80-300 K

    SciTech Connect (OSTI)

    Emel'yanov, A. M. [Russian Academy of Sciences, Ioffe Physicotechnical Institute (Russian Federation)], E-mail: Emelyanov@mail.ioffe.ru

    2008-11-15

    The edge electroluminescence spectra of silicon point-junction light-emitting diodes with a p-n junction area of 0.008 mm{sup 2} are studied at temperatures ranging from 80 to 300 K. Unprecedentedly high stability of the position of the spectral peak is observed at temperatures in the range between 130 and 300 K. The spectral characteristics of the light emitting diodes are studied at 80 K at different current densities up to 25 kA/cm{sup 2}. In contrast to the earlier reported data obtained at 300 K, the data obtained at 80 K do not show any noticeable Augerrecombination-related decrease in the quantum efficiency. From an analysis of the electroluminescence spectra at 80 K in a wide range of currents, it follows that radiative annihilation of free excitons is not a governing mechanism of electroluminescence in the entire emitting region in the base of the point-junction light-emitting diode at all currents used in the experiment.

  13. A 200-A, 500-Hz, triangle current-wave modulator and magnet used for particle beam rastering

    SciTech Connect (OSTI)

    Rose, C.R.; Shafer, R.E.

    1997-10-01

    This paper describes a simple 2D beam-rastering system to uniformly spread a 100-mA 6.7-MeV cw proton beam over a 50-cm by 50-cm beam stop. The basic circuit uses a 20-mF capacitor bank, a IGBT (insulated gate bipolar transistor) full-wave inverter, and a 1-mH ferrite dipole magnet to produce a {+-} 500-Gauss peak triangular-waveform deflection field at 500 Hz. A dc input voltage of 200 volts at 2.6 amps (520 watts) produces a 160-ampere peak-to-peak triangular current waveform in the ferrite magnet at 500 Hz. For dual-axis rastering, two ferrite dipoles are used, one at 500 Hz, and the other at 575 Hz, to produce a uniform 2D beam distribution at the beam stop. The paper will discuss the IGBT modulator and ferrite deflector in detail, including current and voltage waveforms, and the ferrite magnet B-dot (dB/dt) signal.

  14. Φ meson production in d+Au collisions at √sNN = 200 GeV

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Adare, A.

    2015-10-19

    The PHENIX Collaboration has measured Φ meson production in d+Au collisions at √sNN=200 GeV using the dimuon and dielectron decay channels. The Φ meson is measured in the forward (backward) d-going (Au-going) direction, 1.2 T) range from 1–7 GeV/c and at midrapidity |y|T range below 7 GeV/c. The Φ meson invariant yields and nuclear-modification factors as a function of pT, rapidity, and centrality are reported. An enhancement of Φ meson production is observed in the Au-going direction, while suppression is seen in the d-going direction,more »and no modification is observed at midrapidity relative to the yield in p+p collisions scaled by the number of binary collisions. As a result, similar behavior was previously observed for inclusive charged hadrons and open heavy flavor, indicating similar cold-nuclear-matter effects.« less

  15. Mechanical Design and Analysis of a 200 MHz, Bolt-together RFQ forthe Accelerator Driven Neutron Source

    SciTech Connect (OSTI)

    Virostek, Steve; Hoff, Matt; Li, Derun; Staples, John; Wells,Russell

    2007-06-20

    A high-yield neutron source to screen sea-land cargocontainers for shielded Special Nuclear Materials (SNM) has been designedat LBNL [1,2]. The Accelerator-Driven Neutron Source (ADNS) uses theD(d,n)3He reaction to create a forward directed neutron beam. Keycomponents are a high-current radio-frequency quadrupole (RFQ)accelerator and a high-power target capable of producing a neutron fluxof>107 n/(cm2 cdot s) at a distance of 2.5 m. The mechanical designand analysis of the four-module, bolt-together RFQ will be presentedhere. Operating at 200 MHz, the 5.1 m long RFQ will accelerate a 40 mAdeuteron beam to 6 MeV. At a 5 percent duty factor, the time-average d+beam current on target is 1.5 mA. Each of the 1.27 m long RFQ moduleswill consist of four solid OFHC copper vanes. A specially designed 3-DO-ring will provide vacuum sealing between both the vanes and themodules. RF connections are made with canted coil spring contacts. Aseries of 60 water-cooled pi-mode rods provides quadrupole modestabilization. A set of 80 evenly spaced fixed slug tuners is used forfinal frequency adjustment and local field perturbationcorrection.

  16. Open Charm Yields in d+Au Collisions at sqrt(sNN) = 200 GeV

    SciTech Connect (OSTI)

    Adams, J.; Aggarwal, M.M.; Ahammed, Z.; Amonett, J.; Anderson, B.D.; Arkhipkin, D.; Averichev, G.S.; Badyal, S.K.; Bai, Y.; Balewski, J.; Barannikova, O.; Barnby, L.S.; Baudot, J.; Bekele, S.; Belaga, V.V.; Bellwied, R.; Berger, J.; Bezverkhny, B.I.; Bharadwaj, S.; Bhasin, A.; Bhati, A.K.; Bhatia, V.S.; Bichsel, H.; Billmeier, A.; Bland, L.C.; Blyth, C.O.; Bonner, B.E.; Botje, M.; Boucham, A.; Brandin, A.; Bravar, A.; Bystersky, M.; Cadman, R.V.; Cai, X.Z.; Caines, H.; Calderon de la Barca Sanchez, M.; Castillo, J.; Cebra, D.; Chajecki, Z.; Chaloupka, P.; Chattopadhyay, S.; Chen, H.F.; Chen, Y.; Cheng, J.; Cherney, M.; Chikanian, A.; Christie, W.; Coffin, J.P.; Cormier, T.M.; Cramer, J.G.; Crawford, H.J.; Das, D.; Das, S.; De Moura, M.M.; Derevschikov, A.A.; Didenko, L.; Dietel, T.; Dogra, S.M.; Dong, W.J.; Dong, X.; Draper, J.E.; Du, F.; Dubey, A.K.; Dunin, V.B.; Dunlop, J.C.; Dutta Mazumda, M.R.; Eckardt, V.; Edwards, W.R.; Efimov, L.G.; Emelianov, V.; Engelage, J.; Eppley, G.; Erazmus, B.; Estienne, M.; Fachini, P.; Faivre, J.; Fatemi, R.; Fedorisin, J.; Filimonov, K.; Filip, P.; Finch, E.; Fine, V.; Fisyak, Y.; Fomenko, K.; Fu, J.; Gagliardi, C.A.; Gaillard, L.; Gans, J.; Ganti, M.S.; Gaudichet, L.; Geurts, F.; Ghazikhanian, V.; Ghosh, P.; Gonzalez, J.F.; Grachov, O.; Grebenyuk, O.; Grosnick, D.; Guertin, S.M.; Guo, Y.; Gupta, A.; Gutierrez, T.D.; Hallman, T.J.; Hamed, A.; Hardtke, D.; Harris, J.W.; Heinz, M.; Henry, T.W.; Heppelmann, S.; Hippolyte, B.; Hirsch, A.; Hjort, E.; Hoffmann, G.W.; Huang, H.Z.; Huang, S.L.; Hughes, E.W.; Humanic, T.J.; Igo, G.; Ishihara, A.; Ivanshin, Yu.I.; Jacobs, P.; Jacobs, W.W.; Janik, M.; Jiang, H.; Jones, P.G.; Judd, E.G.; Kabana, S.; Kang, K.; Kaplan, M.; Keane, D.; Khodyrev, V.Yu.; Kiryluk, J.; Kisiel, A.; Kislov, E.M.; Klay, J.; Klein, S.R.; Koetke, D.D.; Kollegger, T.; Kopytine, S.M.; Kotchenda, L.; Kramer, M.; Kravtsov, P.; Kravtsov, V.I.; Krueger, K.; Kuhn, C.; Kulikov, A.I.; Kumar, A.; et al.

    2005-01-07

    Mid-rapidity open charm spectra from direct reconstruction of D{sup 0}({bar D}{sup 0}) {yields} K{sup {-+}} {pi}{sup {+-}} in d+Au collisions and indirect electron/positron measurements via charm semileptonic decays in p+p and d+Au collisions at {radical}s{sub NN} = 200 GeV are reported. The D{sup 0}({bar D}{sup 0}) spectrum covers a transverse momentum (p{sub T}) range of 0.1 < p{sub T} < 3 GeV/c whereas the electron spectra cover a range of 1 < p{sub T} < 4 GeV/c. The electron spectra show approximate binary collision scaling between p+p and d+Au collisions. From these two independent analyses, the differential cross section per nucleon-nucleon binary interaction at mid-rapidity for open charm production from d+Au collisions at RHIC is d{sigma}{sub c{bar c}}{sup NN}/dy = 0.30 {+-} 0.04 (stat.) {+-} 0.09(syst.) mb. The results are compared to theoretical calculations. Implications for charmonium results in A+A collisions are discussed.

  17. Pushing HTCondor and glideinWMS to 200K+ Jobs in a Global Pool for CMS before Run 2

    SciTech Connect (OSTI)

    Balcas, J.; Belforte, S.; Bockelman, B.; Gutsche, O.; Khan, F.; Larson, K.; Letts, J.; Mascheroni, M.; Mason, D.; McCrea, A.; Saiz-Santos, M.; Sfiligoi, I.

    2015-12-23

    The CMS experiment at the LHC relies on HTCondor and glideinWMS as its primary batch and pilot-based Grid provisioning system. So far we have been running several independent resource pools, but we are working on unifying them all to reduce the operational load and more effectively share resources between various activities in CMS. The major challenge of this unification activity is scale. The combined pool size is expected to reach 200K job slots, which is significantly bigger than any other multi-user HTCondor based system currently in production. To get there we have studied scaling limitations in our existing pools, the biggest of which tops out at about 70K slots, providing valuable feedback to the development communities, who have responded by delivering improvements which have helped us reach higher and higher scales with more stability. We have also worked on improving the organization and support model for this critical service during Run 2 of the LHC. This contribution will present the results of the scale testing and experiences from the first months of running the Global Pool.

  18. {phi} meson production in Au + Au and p + p collisions at {radical}s{sub NN}=200 GeV

    SciTech Connect (OSTI)

    Adams, J.; Adler, C.; Aggarwal, M.M.; Ahammed, Z.; Amonett, J.; Anderson, B.D.; Arkhipkin, D.; Averichev, G.S.; Badyal, S.K.; Balewski, J.; Barannikova, O.; Barnby, L.S.; Baudot, J.; Bekele, S.; Belaga, V.V.; Bellwied, R.; Berger, J.; Bezverkhny, B.I.; Bhardwaj, S.; Bhati, A.K.; Bichsel, H.; Billmeier, A.; Bland, L.C.; Blyth, C.O.; Bonner, B.E.; Botje, M.; Boucham, A.; Brandin, A.; Bravar, A.; Cadman, R.V.; Cai, X.Z.; Caines, H.; Calderon de la Barca Sanchez, M.; Carroll, J.; Castillo, J.; Cebra, D.; Chaloupka, P.; Chattopadhyay, S.; Chen, H.F.; Chen, Y.; Chernenko, S.P.; Cherney, M.; Chikanian, A.; Christie, W.; Coffin, J.P.; Cormier, T.M.; Cramer, J.G.; Crawford, H.J.; Das, D.; Das, S.; Derevschikov, A.A.; Didenko, L.; Dietel, T.; Dong, W.J.; Dong, X.; Draper, J.E.; Du, F.; Dubey, A.K.; Dunin, V.B.; Dunlop, J.C.; Dutta Majumdar, M.R.; Eckardt, V.; Efimov, L.G.; Emelianov, V.; Engelage, J.; Eppley, G.; Erazmus, B.; Estienne, M.; Fachini, P.; Faine, V.; Faivre, J.; Fatemi, R.; Filimonov, K.; Filip, P.; Finch, E.; Fisyak, Y.; Flierl, D.; Foley, K.J.; Fu, J.; Gagliardi, C.A.; Gagunashvili, N.; Gans, J.; Ganti, M.S.; Gaudichet, L.; Germain, M.; Geurts, F.; Ghazikhanian, V.; Ghosh, P.; Gonzalez, J.E.; Grachov, O.; Grebenyuk, O.; Gronstal, S.; Grosnick, D.; Guedon, M.; Guertin, S.M.; Gupta, A.; Gutierrez, T.D.; Hallman, T.J.; Hamed, A.; Hardtke, D.; Harris, J.W.; Heinz, M.; Henry, T.W.; Heppelmann, S.; Hippolyte, B.; Hirsch, A.; Hjort, E.; Hoffmann, G.W.; Horsley, M.; Huang, H.Z.; Huang, S.L.; Hughes, E.; Humanic, T.J.; Igo, G.; Ishihara, A.; Jacobs, P.; Jacobs, W.W.; Janik, M.; Johnson, I.; Jones, P.G.; Judd, E.G.; Kabana, S.; Kaplan, M.; Keane, D.; Khodyrev; Kiryluk, J.; Kisiel, A.; Klay, J.; Klein, S.R.; Klyachko, A.; Koetke, D.D.; Kollegger, T.; Kopytine, S.M.; Kotchenda, L.; Kovalenko, A.D.; Kramer, M.; Kravtsov, P.; Kravstov, V.I.; Krueger, K.; Kuhn, C.; Kulikov, A.I.; Kumar, A.; Kunde, G.J.; Kunz, C.L.; Kutuev, R.Kh.; et al.

    2004-06-01

    We report the STAR measurement of {psi} meson production in Au + Au and p + p collisions at {radical}s{sub NN} = 200 GeV. Using the event mixing technique, the {psi} spectra and yields are obtained at midrapidity for five centrality bins in Au+Au collisions and for non-singly-diffractive p+p collisions. It is found that the {psi} transverse momentum distributions from Au+Au collisions are better fitted with a single-exponential while the p+p spectrum is better described by a double-exponential distribution. The measured nuclear modification factors indicate that {psi} production in central Au+Au collisions is suppressed relative to peripheral collisions when scaled by the number of binary collisions (). The systematics of versus centrality and the constant {psi}/K{sup -} ratio versus beam species, centrality, and collision energy rule out kaon coalescence as the dominant mechanism for {psi} production.

  19. Φ meson production in d+Au collisions at √sNN = 200 GeV

    SciTech Connect (OSTI)

    Adare, A.

    2015-10-19

    The PHENIX Collaboration has measured Φ meson production in d+Au collisions at √sNN=200 GeV using the dimuon and dielectron decay channels. The Φ meson is measured in the forward (backward) d-going (Au-going) direction, 1.2 < y < 2.2 (–2.2 < y < –1.2) in the transverse-momentum (pT) range from 1–7 GeV/c and at midrapidity |y|<0.35 in the pT range below 7 GeV/c. The Φ meson invariant yields and nuclear-modification factors as a function of pT, rapidity, and centrality are reported. An enhancement of Φ meson production is observed in the Au-going direction, while suppression is seen in the d-going direction, and no modification is observed at midrapidity relative to the yield in p+p collisions scaled by the number of binary collisions. As a result, similar behavior was previously observed for inclusive charged hadrons and open heavy flavor, indicating similar cold-nuclear-matter effects.

  20. Φ meson production in d+Au collisions at √sNN = 200 GeV

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Adare, A.

    2015-10-19

    The PHENIX Collaboration has measured Φ meson production in d+Au collisions at √sNN=200 GeV using the dimuon and dielectron decay channels. The Φ meson is measured in the forward (backward) d-going (Au-going) direction, 1.2 < y < 2.2 (–2.2 < y < –1.2) in the transverse-momentum (pT) range from 1–7 GeV/c and at midrapidity |y|<0.35 in the pT range below 7 GeV/c. The Φ meson invariant yields and nuclear-modification factors as a function of pT, rapidity, and centrality are reported. An enhancement of Φ meson production is observed in the Au-going direction, while suppression is seen in the d-going direction,more » and no modification is observed at midrapidity relative to the yield in p+p collisions scaled by the number of binary collisions. As a result, similar behavior was previously observed for inclusive charged hadrons and open heavy flavor, indicating similar cold-nuclear-matter effects.« less

  1. Around 200 new X-ray binary IDs from 13 YR of Chandra observations of the M31 center

    SciTech Connect (OSTI)

    Barnard, R.; Garcia, M. R.; Primini, F.; Li, Z.; Baganoff, F. K.; Murray, S. S.

    2014-01-01

    We have created 0.3-10 keV, 13 yr, unabsorbed luminosity lightcurves for 528 X-ray sources in the central 20' of M31. We have 174 Chandra observations spaced at ?1 month intervals due to our transient monitoring program, deeper observations of the M31 nucleus, and some public data from other surveys. We created 0.5-4.5 keV structure functions (SFs) for each source for comparison with the ensemble SF of active galactic nuclei (AGN). We find 220 X-ray sources with luminosities ?10{sup 35} erg s{sup 1} that have SFs with significantly more variability than the ensemble AGN SF, and which are likely X-ray binaries (XBs). A further 30 X-ray sources were identified as XBs using other methods. We therefore have 250 probable XBs in total, including ?200 new identifications. This result represents great progress over the ?50 XBs and ?40 XB candidates previously identified out of the ?2000 X-ray sources within the D {sub 25} region of M31; it also demonstrates the power of SF analysis for identifying XBs in external galaxies. We also identify a new transient black hole candidate, associated with the M31 globular cluster B128.

  2. Experimental investigation of neutron emissions during thermal cycling of TiD{sub x} (x {approx} 2.00)

    SciTech Connect (OSTI)

    Fernandez, J.F.; Cuevas, F.; Alguero, M.; Sanchez, C.

    1997-03-01

    The production of neutrons from D + D reactions in thermally cycled titanium deuteride (TiD{sub x}) (x {approx} 2) is investigated in depth. Special attention is given to cubic-tetragonal ({delta} - {epsilon}) phase transition that TiD{sub x} experiences near room temperature as a possible triggering mechanism of `cold nuclear fusion reactions.` The TiD{sub x} (x {approx} 2.00) samples, possessing well-known properties about the {delta} - {epsilon} transition, are cycled at temperatures (from -60 to 60{degree} C) where the phase transition takes place. The cold fusion signature is investigated by measuring the neutron flux of the sample during the experiments. No significant neutron signal above the background level is found during thermal cycling of the TiD{sub x} samples. It is concluded that in the samples investigated, no correlation exists between the {delta} - {epsilon} transition and the trigger of the D + D reactions. Background deviations give an upper limit of the rate of the D + D {yields} {sup 3}He + n reaction of {lambda} < 10{sup -23} fusion/p-d.s. 32 refs., 8 figs., 4 tabs.

  3. MHD advanced power train. Phase 1, Final report: Volume 3, Power train system description and specification for 200MWe Plant

    SciTech Connect (OSTI)

    Jones, A.R.

    1985-08-01

    This System Design Description and Specification provides the basis for the design of the magnetohydrodynamic (MHD) Power Train (PT) for a nominal 200 MWe early commercial tiHD/Steam Power Plant. This document has been developed under Task 2, Conceptual Design, of Contract DE-AC22-83PC60575 and is to be used by the project as the controlling and coordinating documentation during future design efforts. Modification and revision of this specification will occur as the design matures, and tiie-Westinghouse MHD Project Manager will be the focal point for maintaining this document and issuing periodic revisions. This document is intended to delineate the power train and-power train components requirements and assumptions that properly reflect the MHD/Steam Power Plant in the PT design. The parameters discussed in this document have been established through system calculations as well as through constraints set by technology and by limitations on materials, cost, physical processes associated with MHD, and the expected operating data for the plant. The specifications listed in this document have precedence over all referenced documents. Where this specification appears to conflict with the requirements of a reference document, such conflicts should be brought to the attention of the Westinghouse MHD Project Manager for resolution.

  4. Transverse energy production and charged-particle multiplicity at midrapidity in various systems from sNN=7.7 to 200 GeV

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Adare, A.; Afanasiev, S.; Aidala, C.; Ajitanand, N. N.; Akiba, Y.; Akimoto, R.; Al-Bataineh, H.; Alexander, J.; Alfred, M.; Al-Jamel, A.; et al

    2016-02-03

    Measurements of midrapidity charged-particle multiplicity distributions, dNch/dη, and midrapidity transverse-energy distributions, dET/dη, are presented for a variety of collision systems and energies. Included are distributions for Au+Au collisions at √sNN=200, 130, 62.4, 39, 27, 19.6, 14.5, and 7.7 GeV, Cu+Cu collisions at √sNN=200 and 62.4 GeV, Cu+Au collisions at √sNN=200 GeV, U+U collisions at√sNN=193 GeV, d+Au collisions at √sNN=200 GeV, He3+Au collisions at √sNN=200 GeV, and p+p collisions at √sNN=200 GeV. We present centrality-dependent distributions at midrapidity in terms of the number of nucleon participants, Npart, and the number of constituent quark participants, Nqp. For all A+A collisions down tomore » √sNN=7.7 GeV, we observed that the midrapidity data are better described by scaling with Nqp than scaling with Npart. Finally, our estimates of the Bjorken energy density, εBJ, and the ratio of dET/dη to dNch/dη are presented, the latter of which is seen to be constant as a function of centrality for all systems.« less

  5. Nucleon-gold collisions at 200A GeV using tagged d + Au interactions in the PHOBOS detector

    SciTech Connect (OSTI)

    Back, B. B.; Nouicer, R.; Baker, M. D.; Ballintijn, M.; Barton, D. S.; Becker, B.; Betts, R. R.; Bickley, A. A; Stienberg, P.; Ioradnova, A.; Pak, R.; Sukhanov, A.

    2015-09-23

    Forward calorimetry in the PHOBOS detector has been used to study charged hadron production in d+Au, p+Au, and n+Au collisions at √sNN =200GeV. The forward proton calorimeter detectors are described and a procedure for determining collision centrality with these detectors is detailed. The deposition of energy by deuteron spectator nucleons in the forward calorimeters is used to identify p+Au and n+Au collisions in the data. A weighted combination of the yield of p+Au and n+Au is constructed to build a reference for Au+Au collisions that better matches the isospin composition of the gold nucleus. The pT and centrality dependence of the yield of this improved reference system is found to match that of d+Au. The shape of the charged-particle transverse momentum distribution is observed to extrapolate smoothly from p+p¯ to central d+Au as a function of the charged-particle pseudorapidity density. The asymmetry of positively and negatively charged hadron production in p+Au is compared to that of n+Au. No significant asymmetry is observed at midrapidity. In conclusion, these studies augment recent results from experiments at the CERN Large Hadron Collider and BNL Relativistic Heavy Ion Collider facilities to give a more complete description of particle production in p+A and d+A collisions, essential for the understanding the medium produced in high-energy nucleus-nucleus collisions.

  6. Nucleon-gold collisions at 200A GeV using tagged d + Au interactions in the PHOBOS detector

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Back, B. B.; Nouicer, R.; Baker, M. D.; Ballintijn, M.; Barton, D. S.; Becker, B.; Betts, R. R.; Bickley, A. A; Stienberg, P.; Ioradnova, A.; et al

    2015-09-23

    Forward calorimetry in the PHOBOS detector has been used to study charged hadron production in d+Au, p+Au, and n+Au collisions at √sNN =200GeV. The forward proton calorimeter detectors are described and a procedure for determining collision centrality with these detectors is detailed. The deposition of energy by deuteron spectator nucleons in the forward calorimeters is used to identify p+Au and n+Au collisions in the data. A weighted combination of the yield of p+Au and n+Au is constructed to build a reference for Au+Au collisions that better matches the isospin composition of the gold nucleus. The pT and centrality dependence ofmore » the yield of this improved reference system is found to match that of d+Au. The shape of the charged-particle transverse momentum distribution is observed to extrapolate smoothly from p+p¯ to central d+Au as a function of the charged-particle pseudorapidity density. The asymmetry of positively and negatively charged hadron production in p+Au is compared to that of n+Au. No significant asymmetry is observed at midrapidity. In conclusion, these studies augment recent results from experiments at the CERN Large Hadron Collider and BNL Relativistic Heavy Ion Collider facilities to give a more complete description of particle production in p+A and d+A collisions, essential for the understanding the medium produced in high-energy nucleus-nucleus collisions.« less

  7. Safety analysis--200 Area Savannah River Site: Separations Area operations Building 211-H Outside Facilities. Supplement 11, Revision 1

    SciTech Connect (OSTI)

    Not Available

    1993-01-01

    The H-Area Outside Facilities are located in the 200-H Separations Area and are comprised of a number of processes, utilities, and services that support the separations function. Included are enriched uranium loadout, bulk chemical storage, water handling, acid recovery, general purpose evaporation, and segregated solvent facilities. In addition, services for water, electricity, and steam are provided. This Safety Analysis Report (SAR) documents an analysis of the H-Area Outside Facilities and is one of a series of documents for the Separations Area as specified in the SR Implementation Plan for DOE order 5481.1A. The primary purpose of the analysis was to demonstrate that the facility can be operated without undue risk to onsite or offsite populations, to the environment, and to operating personnel. In this report, risks are defined as the expected frequencies of accidents, multiplied by the resulting radiological consequences in person-rem. Following the summary description of facility and operations is the site evaluation including the unique features of the H-Area Outside Facilities. The facility and process design are described in Chapter 3.0 and a description of operations and their impact is given in Chapter 4.0. The accident analysis in Chapter 5.0 is followed by a list of safety related structures and systems (Chapter 6.0) and a description of the Quality Assurance program (Chapter 7.0). The accident analysis in this report focuses on estimating the risk from accidents as a result of operation of the facilities. The operations were evaluated on the basis of three considerations: potential radiological hazards, potential chemical toxicity hazards, and potential conditions uniquely different from normal industrial practice.

  8. Measurements of dielectron production in Au + Au collisions at sNN=200 GeV from the STAR experiment

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Adamczyk, L.; Adkins, J. K.; Agakishiev, G.; Aggarwal, M. M.; Ahammed, Z.; Alekseev, I.; Alford, J.; Aparin, A.; Arkhipkin, D.; Aschenauer, E. C.; et al

    2015-08-24

    We report on measurements of dielectron (e⁺e⁻) production in Au+Au collisions at a center-of-mass energy of 200 GeV per nucleon-nucleon pair using the STAR detector at RHIC. Systematic measurements of the dielectron yield as a function of transverse momentum (pT) and collision centrality show an enhancement compared to a cocktail simulation of hadronic sources in the low invariant-mass region (Mee < 1GeV/c2). This enhancement cannot be reproduced by the ρ-meson vacuum spectral function. In minimum-bias collisions, in the invariant-mass range of 0.30 – 0.76GeV/c², integrated over the full pT acceptance, the enhancement factor is 1.76±0.06(stat.)±0.26(sys.)±0.29(cocktail). The enhancement factor exhibits weakmore » centrality and pT dependence in STAR's accessible kinematic regions, while the excess yield in this invariant-mass region as a function of the number of participating nucleons follows a power-law shape with a power of 1.44±0.10. Models that assume an in-medium broadening of the ρ-meson spectral function consistently describe the observed excess in these measurements. In addition, we report on measurements of ω- and Φ-meson production through their e⁺e⁻ decay channel. These measurements show good agreement with Tsallis blast-wave model predictions, as well as, in the case of the Φ meson, results through its K⁺K⁻ decay channel. In the intermediate invariant-mass region (1.1 < Mee < 3GeV/c²), we investigate the spectral shapes from different collision centralities. Physics implications for possible in-medium modification of charmed hadron production and other physics sources are discussed.« less

  9. Interferometry radii in heavy-ion collisions at {radical}(s)=200 GeV and 2.76 TeV

    SciTech Connect (OSTI)

    Bozek, Piotr

    2011-04-15

    The expansion of the fireball created in Au-Au collisions at {radical}(s)=200 GeV and Pb-Pb collisions at 2.76 TeV is modelled using relativistic viscous hydrodynamics. The experimentally observed interferometry radii are well reproduced. Additional pre-equilibrium flow slightly improves the results for the lower energies studied.

  10. Susceptibility of Granite Rock to scCO2/Water at 200 degrees C and 250 degrees C

    SciTech Connect (OSTI)

    Sugama, T.; Gill, S., Ecker, L., Butcher, T., Warren, J.

    2011-01-01

    of the non-carbonated surfaces of the underlying rock was reason why the hornblende and diorite exhibited a minimum depth of carbonation. Under exposure to the scCO{sub 2}/water at 200 C and 10.34 MPa pressure for up to 42 days, the ranking of the magnitude of erosion caused by wet carbonation was in the following order; granite > albite > hornblende > diorite > quartz. The eroding-caused weight loss of granite (0.88 %) was {approx}2.4, {approx}5.2, {approx}9.8, and {approx}17.6 times greater than that of albite, hornblends, diorite, and quartz, respectively.

  11. Modeling of collision-induced infrared absorption spectra of H2-H2 pairs in the fundamental band at temperatures from 20 to 300 K. [Planetary atmospheres

    SciTech Connect (OSTI)

    Borysow, A. )

    1991-08-01

    The 20-300 K free-free rotovibrational collision-induced absorption (RV CIA) spectra of H2-H2 pairs are presently obtained by a numerical method which, in addition to closely matching known CIA spectra of H2-H2, can reproduce the results of the quantum-mechanical computations to within a few percent. Since the spectral lineshape parameters are derivable by these means from the lowest three quantum-mechanical spectral moments, these outer-planet atmosphere-pertinent model spectra may be computed on even small computers. 35 refs.

  12. Measurement of residual nucleus cross sections and recoil energies in p + Fe collisions at 300, 500, 750, 1000 and 1500 MeV

    SciTech Connect (OSTI)

    Villagrasa, C.; Boudard, A.; Ducret, J.-E.; Fernandez, B.; Leray, S.; Volant, C.; Wlazlo, W.; Audouin, L.; Ferran, L.; Rejmund, F.

    2005-05-24

    The production of residual nuclei in p + Fe collisions has been measured at GSI on the FRS facility by means of the reverse kinematic techniques at 300, 500, 750, 1000 and 1500 MeV/A. The cross-sections larger than 0.01 mb of all isotopes with Z larger than 8 have been obtained. Velocity distributions were also measured. Comparisons to models describing spallation reactions and some empirical formulae often used in astrophysics are presented. These data are directly used to calculate impurity production and DPAs in a thin window as foreseen in spallation sources or accelerator-driven systems.

  13. The Multi-Scale Mass Transfer Processes Controlling Natural Attenuation and Engineered Remediation: An IFC Focused on Hanford’s 300 Area Uranium Plume Quality Assurance Project Plan

    SciTech Connect (OSTI)

    Fix, N. J.

    2008-01-31

    The purpose of the project is to conduct research at an Integrated Field-Scale Research Challenge Site in the Hanford Site 300 Area, CERCLA OU 300-FF-5 (Figure 1), to investigate multi-scale mass transfer processes associated with a subsurface uranium plume impacting both the vadose zone and groundwater. The project will investigate a series of science questions posed for research related to the effect of spatial heterogeneities, the importance of scale, coupled interactions between biogeochemical, hydrologic, and mass transfer processes, and measurements/approaches needed to characterize a mass-transfer dominated system. The research will be conducted by evaluating three (3) different hypotheses focused on multi-scale mass transfer processes in the vadose zone and groundwater, their influence on field-scale U(VI) biogeochemistry and transport, and their implications to natural systems and remediation. The project also includes goals to 1) provide relevant materials and field experimental opportunities for other ERSD researchers and 2) generate a lasting, accessible, and high-quality field experimental database that can be used by the scientific community for testing and validation of new conceptual and numerical models of subsurface reactive transport.

  14. Experimental determination of single-crystal halite thermal conductivity, diffusivity and specific heat from -75°C to 300°C

    SciTech Connect (OSTI)

    Urquhart, Alexander; Bauer, Stephen

    2015-05-19

    The thermal properties of halite have broad practical importance, from design and long-term modeling of nuclear waste repositories to analysis and performance assessment of underground natural gas, petroleum and air storage facilities. Using a computer-controlled transient plane source method, single-crystal halite thermal conductivity, thermal diffusivity and specific heat were measured from -75°C to 300°C. These measurements reproduce historical high-temperature experiments and extend the lower temperature extreme into cryogenic conditions. Measurements were taken in 25-degree increments from -75°C to 300°C. Over this temperature range, thermal conductivity decreases by a factor of 3.7, from 9.975 to 2.699 W/mK , and thermal diffusivity decreases by a factor of 3.6, from 5.032 to 1.396 mm²/s. Specific heat does not appear to be temperature dependent, remaining near 2.0 MJ/m³K at all temperatures. This work is intended to develop and expand the existing dataset of halite thermal properties, which are of particular value in defining the parameters of salt storage thermophysical models. The work was motivated by a need for thermal conductivity values in a mixture theory model used to determine bulk thermal conductivity of reconsolidating crushed salt.

  15. Experimental determination of single-crystal halite thermal conductivity, diffusivity and specific heat from -75°C to 300°C

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Urquhart, Alexander; Bauer, Stephen

    2015-05-19

    The thermal properties of halite have broad practical importance, from design and long-term modeling of nuclear waste repositories to analysis and performance assessment of underground natural gas, petroleum and air storage facilities. Using a computer-controlled transient plane source method, single-crystal halite thermal conductivity, thermal diffusivity and specific heat were measured from -75°C to 300°C. These measurements reproduce historical high-temperature experiments and extend the lower temperature extreme into cryogenic conditions. Measurements were taken in 25-degree increments from -75°C to 300°C. Over this temperature range, thermal conductivity decreases by a factor of 3.7, from 9.975 to 2.699 W/mK , and thermal diffusivitymore » decreases by a factor of 3.6, from 5.032 to 1.396 mm²/s. Specific heat does not appear to be temperature dependent, remaining near 2.0 MJ/m³K at all temperatures. This work is intended to develop and expand the existing dataset of halite thermal properties, which are of particular value in defining the parameters of salt storage thermophysical models. The work was motivated by a need for thermal conductivity values in a mixture theory model used to determine bulk thermal conductivity of reconsolidating crushed salt.« less

  16. Selection Tests of MnZn and NiZn Ferrites for Mu2e 300 kHz and 5.1 MHz AC Dipoles

    SciTech Connect (OSTI)

    Bourkland, K.; Elementi, L.; Feher, S.; Harding, D.J.; Kashikhin, V.S.; Makarov, A.; Pfeffer, H.; Velev, G.V.; Mulushev, E.; Iedmeska, I.; Venturini, M.; /Pisa U.

    2011-09-09

    Mu2e, a charged lepton flavor violation (CLFV) experiment is planned to start at Fermilab late in this decade. The proposed experiment will search for neutrinoless muon to electron conversions with unprecedented sensitivity, better than 6 x 10{sup -17 }at 90% CL. To achieve this sensitivity the incoming proton beam must be highly suppressed during the window for detecting the muon decays. The current proposal for beam extinction is based on a collimator design with two dipoles running at {approx}300 kHz and 5.1 MHz and synchronized to the proton bunch spacing. The appropriate choice of ferrite material for the magnet yoke is a critical step in the overall design of the dipoles and their reliable operation at such high frequencies over the life of the experiment. This choice, based on a series of the thermal and magnetic measurements of the ferrite samples, is discussed in the paper. Additionally, the first results from the testing at 300 kHz of a prototype AC dipole are presented.

  17. FINAL PROJECT REPORT: A Geophysical Characterization & Monitoring Strategy for Determining Hydrologic Processes in the Hyporheic Corridor at the Hanford 300-Area

    SciTech Connect (OSTI)

    Lee Slater

    2011-08-15

    The primary objective of this research was to advance the prediction of solute transport between the Uranium contaminated Hanford aquifer and the Columbia River at the Hanford 300 Area by improving understanding of how fluctuations in river stage, combined with subsurface heterogeneity, impart spatiotemporal complexity to solute exchange along the Columbia River corridor. Our work explored the use of continuous waterborne electrical imaging (CWEI), in conjunction with fiber-optic distributed temperature sensor (FO-DTS) and time-lapse resistivity monitoring, to improve the conceptual model for how groundwater/surface water exchange regulates uranium transport. We also investigated how resistivity and induced polarization can be used to generate spatially rich estimates of the variation in depth to the Hanford-Ringold (H-R) contact between the river and the 300 Area Integrated Field Research Challenge (IFRC) site. Inversion of the CWEI datasets (a data rich survey containing ~60,000 measurements) provided predictions of the distributions of electrical resistivity and polarizability, from which the spatial complexity of the primary hydrogeologic units along the river corridor was reconstructed. Variation in the depth to the interface between the overlying coarse-grained, high permeability Hanford Formation and the underlying finer-grained, less permeable Ringold Formation, an important contact that limits vertical migration of contaminants, has been resolved along ~3 km of the river corridor centered on the IFRC site in the Hanford 300 Area. Spatial variability in the thickness of the Hanford Formation captured in the CWEI datasets indicates that previous studies based on borehole projections and drive-point and multi-level sampling likely overestimate the contributing area for uranium exchange within the Columbia River at the Hanford 300 Area. Resistivity and induced polarization imaging between the river and the 300 Area IFRC further imaged spatial variability in

  18. Preliminary Results of Mono-energetic Electron Beams from a Laser-plasma Accelerator Driven by 200 TW Femto Second Pulses

    SciTech Connect (OSTI)

    Taki, R.; Kameshima, T.; An, W. M.; Hua, J. F.; Huang, W. H.; Tang, C. X.; Gu, Y. Q.; Guo, Y.; Hong, W.; Jiao, C. Y.; Lin, Y. Z.; Liu, H. J.; Peng, H. S.; Sun, L.; Tang, C. M.; Wang, X. D.; Wen, T. S.; Wen, X. L.; Wu, Y. C.; Zhang, B. H.

    2006-11-27

    Relativistic mono-energetic electron beams have been demonstrated by worldwide laser-plasma accelerator experiments in the range of a few tens TW. Laser-plasma accelerator experiment has been carried out with 200TW, 30fs Ti:Sapphire laser pulses focused on helium gas-jets with F/8.7 optics. Intense mono-energetic electron beams have been produced in the energy range of 30 to 150 MeV by controlling plasma length and density precisely. Images of Thomson scattering and fluorescence side scattering from plasma indicate highly relativistic effects such as a long self-channeling and filamentation as well as energetic electron deflection and intense backward Raman scattering. Preliminary results of the first laser-plasma accelerator experiment in the range of 200TW femto second pulses are presented.

  19. SINGLE SPIN ASYMMETRIES OF IDENTIFIED HADRONS IN p +p AT SQUARE ROOT S = 62.4 AND 200 GeV.

    SciTech Connect (OSTI)

    LEE,J.H.; VIDEBAEK, F.

    2007-04-16

    Measurements of x{sub F}-dependent single spin asymmetries of identified charged hadrons, {pi}{sup {+-}}, K{sup {+-}}, p, and {bar p}, from transversely polarized proton collisions at {radical}s = 200 and 62.4 GeV at RHIC are presented. The energy and flavor dependent asymmetry measurements bring new insight into the fundamental mechanisms of transverse spin asymmetries and Quantum Chromodynamical description of hadronic structure.

  20. Use of Electrical Imaging and Distributed Temperature Sensing Methods to Characterize Surface Water-Groundwater Exchange Regulating Uranium Transport at the Hanford 300 Area, Washington

    SciTech Connect (OSTI)

    Slater, Lee; Ntarlagiannis, Dimitrios; Day-Lewis, Frederick D.; Mwakanyamale, Kisa; Versteeg, Roelof J.; Ward, Anderson L.; Strickland, Christopher E.; Johnson, Carole D.; Lane, John W.

    2010-10-31

    A critical challenge in advancing prediction of solute transport between contaminated aquifers and rivers is improving understanding of how fluctuations in river stage, combined with subsurface heterogeneity, impart spatiotemporal complexity to solute exchange along river corridors. Here, we explored the use of waterborne geoelectrical imaging, in conjunction with fiber-optic distributed temperature sensor (DTS) monitoring, to improve the conceptual model for uranium transport within the hyporheic corridor at the Hanford 300 Area. We first inverted waterborne geoelectrical (resistivity and induced polarization) datasets for distributions of electrical resistivity and polarizability, from which the spatial complexity of the primary hydrogeologic units was reconstructed. Variations in the depth to the interface between the overlying coarse-grained, high permeability Hanford formation and the underlying finer-grained, less permeable Ringold formation, an important contact that limits vertical migration of contaminants, were resolved along ~3 km of the river corridor centered on the 300 Area. Polarizability images were translated into lithologic images using established relationships between polarizability and surface area normalized to pore volume (Spor). The spatial variability captured in the geoelectrical datasets indicates that previous studies based on borehole projections and point probing overestimate the contributing area for uranium exchange within the Columbia River at the Hanford 300 Area. The DTS data recorded on 1. 5 km of cable with a 1 m spatial resolution and 5 minute sampling interval revealed sub-reaches showing (1) high temperature anomalies and, (2) a strong negative correlation between temperature and river stage, both indicative of groundwater influxes during winter months. The DTS datasets confirm the hydrologic significance of the variability identified in the geoelectrical imaging and reveal a pattern of highly focused hyporheic exchange, with