Powered by Deep Web Technologies
Note: This page contains sample records for the topic "4-cylinder electric motor" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


1

Electric Motors  

Broader source: Energy.gov [DOE]

Section 313 of the Energy Independence and Security Act (EISA) of 2007 raised Federal minimum efficiency standards for general-purpose, single-speed, polyphase induction motors of 1 to 500 horsepower (hp). This new standard took effect in December 2010. The new minimum efficiency levels match FEMP's performance requirement for these motors.

2

Electric motors: Markets, trends, and applications  

SciTech Connect (OSTI)

Electric motors play an important role in nearly all sectors of the US economy. Typical motor applications range from air conditioning and appliances in the residential sector, to cooling and space heating in the commercial sector, to materials handling and processing in the industrial sectors. Motors in the residential sector consumed nearly 352 billion kilowatthours (BkWh) in 1985, in the commercial sector 279 BkWh, and the industrial sector 552 BkWh. Approximately 87% of electric motor electricity use in the industrial sector was consumed in manufacturing processes, while the process industries consumed more than half of the manufacturing sector's electric motor electricity use. The total motor population in all sectors in 1987 stood just shy of 1.02 billion, 90% of which are less than one horsepower (HP) in size. An increasing percentage of the motor population is comprised of high efficiency motors, as classified by the National Electrical Manufacturers Association (NEMA). High efficiency motors offer end-users greater energy and cost savings than do their standard efficiency counterparts. This report provides an overview of the history of the electric motor, a brief description of the electromechanical theory behind motor operations, and offers a statistical review of the size and distribution of the electric motor market. The report also presents data on sector motor electricity use, describes current and potential motor application opportunities, and details areas in which further research and development may be needed.

Not Available

1992-06-01T23:59:59.000Z

3

Electric Motor What happens if we put  

E-Print Network [OSTI]

Electric Motor What happens if we put a loop of wire carrying a current in a B field ? FB on opposite sides of the loop produce a torque on the loop causing it to rotate. Electric motor ­ a commutator. #12;Electric Motor Define normal n to plane using right-hand rule Torque tends to rotate loop to align

Bertulani, Carlos A. - Department of Physics and Astronomy, Texas A&M University

4

Electrical system for a motor vehicle  

DOE Patents [OSTI]

In one embodiment of the present invention, an electrical system for a motor vehicle comprises a capacitor, an engine cranking motor coupled to receive motive power from the capacitor, a storage battery and an electrical generator having an electrical power output, the output coupled to provide electrical energy to the capacitor and to the storage battery. The electrical system also includes a resistor which limits current flow from the battery to the engine cranking motor. The electrical system further includes a diode which allows current flow through the diode from the generator to the battery but which blocks current flow through the diode from the battery to the cranking motor. 2 figs.

Tamor, M.A.

1999-07-20T23:59:59.000Z

5

Electrical system for a motor vehicle  

DOE Patents [OSTI]

In one embodiment of the present invention, an electrical system for a motor vehicle comprises a capacitor, an engine cranking motor coupled to receive motive power from the capacitor, a storage battery and an electrical generator having an electrical power output, the output coupled to provide electrical energy to the capacitor and to the storage battery. The electrical system also includes a resistor which limits current flow from the battery to the engine cranking motor. The electrical system further includes a diode which allows current flow through the diode from the generator to the battery but which blocks current flow through the diode from the battery to the cranking motor.

Tamor, Michael Alan (Toledo, OH)

1999-01-01T23:59:59.000Z

6

Electric Motors and Critical Materials  

Broader source: Energy.gov (indexed) [DOE]

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May Jun Jul(Summary) "ofEarly Career Scientists'Montana.Program - LibbyofThisStatement Tuesday,DepartmentTheand ContactELECTRIC MOTORS

7

Electric motor model repair specifications  

SciTech Connect (OSTI)

These model repair specifications list the minimum requirements for repair and overhaul of polyphase AC squireel cage induction motors. All power ranges, voltages, and speeds of squirrel cage motors are covered.

NONE

1995-08-01T23:59:59.000Z

8

EV Everywhere Workshop: Electric Motors and Critical Materials...  

Broader source: Energy.gov (indexed) [DOE]

Electric Motors and Critical Materials Breakout Group Report EV Everywhere Workshop: Electric Motors and Critical Materials Breakout Group Report Presentation given at the EV...

9

DOE Issues Notice of Proposed Rulemaking for Electric Motors...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Notice of Proposed Rulemaking for Electric Motors Energy Conservation Standards DOE Issues Notice of Proposed Rulemaking for Electric Motors Energy Conservation Standards November...

10

Quality electric motor repair: A guidebook for electric utilities  

SciTech Connect (OSTI)

This guidebook provides utilities with a resource for better understanding and developing their roles in relation to electric motor repair shops and the industrial and commercial utility customers that use them. The guidebook includes information and tools that utilities can use to raise the quality of electric motor repair practices in their service territories.

Schueler, V.; Douglass, J.

1995-08-01T23:59:59.000Z

11

Energy-Efficient Electric Motor Selection Handbook  

SciTech Connect (OSTI)

Substantial reductions in energy and operational costs can be achieved through the use of energy-efficient electric motors. A handbook was compiled to help industry identify opportunities for cost-effective application of these motors. It covers the economic and operational factors to be considered when motor purchase decisions are being made. Its audience includes plant managers, plant engineers, and others interested in energy management or preventative maintenance programs.

McCoy, Gilbert A.; Litman, Todd; Douglass, John G.

1990-10-01T23:59:59.000Z

12

Oscillation control system for electric motor drive  

DOE Patents [OSTI]

A feedback system for controlling mechanical oscillations in the torsionally complaint drive train of an electric or other vehicle. Motor speed is converted in a processor to estimate state signals in which a plant model which are used to electronically modify thetorque commands applied to the motor.

Slicker, James M. (Union Lake, MI); Sereshteh, Ahmad (Union Lake, MI)

1988-01-01T23:59:59.000Z

13

Oscillation control system for electric motor drive  

DOE Patents [OSTI]

A feedback system for controlling mechanical oscillations in the torsionally complaint drive train of an electric or other vehicle. Motor speed is converted in a processor to estimate state signals in which a plant model which are used to electronically modify the torque commands applied to the motor. 5 figs.

Slicker, J.M.; Sereshteh, A.

1988-08-30T23:59:59.000Z

14

Development of Ulta-Efficient Electric Motors  

SciTech Connect (OSTI)

Electric motors utilize a large amount of electrical energy in utility and industrial applications. Electric motors constructed with high temperature superconducting (HTS) materials have the potential to dramatically reduce electric motor size and losses. HTS motors are best suited for large motor applications at ratings above 1000 horsepower (hp), where the energy savings from the efficiency improvement can overcome the additional power required to keep the superconductors on the rotor cooled. Large HTS based motors are expected to be half the volume and have half the losses of conventional induction motors of the same rating. For a 5000 hp industrial motor, this energy savings can result in $50,000 in operating cost savings over the course of a single year of operation. Since large horsepower motors utilize (or convert) about 30% of the electrical power generated in the United States and about 70% of large motors are candidates for replacement by HTS motors, the annual energy savings potential through the utilization of HTS motors can be up to $1 Billion in the United States alone. Research in the application of HTS materials to electric motors has lead to a number of HTS motor prototypes yet no industrial HTS motor product has yet been introduced. These motor demonstrations have been synchronous motors with HTS field windings, on the rotor. Figure 1-1 shows a solid model rendering of this type of motor. The rotor winding is made with HTS coils that are held at cryogenic temperature by introducing cooling fluid from the cryocooler to the rotor through a transfer coupling. The stator winding is made of copper wire. The HTS winding is thermally isolated from the warm armature and motor shafts by a vacuum insulation space and through the use of composite torque tubes. The stator in Figure 1-1 is an air core stator in that the stator teeth and a small part of the yoke is made up of nonmagnetic material so the magnetic fields distribute themselves as if in air. Between the HTS field winding and the physical air gap is a series of concentric cylinders that act as vacuum insulation space walls as well as conducting paths for induced currents to flow in order to shield the HTS winding and the rotor cold space from time dependent fields. These time dependent fields may be caused by rotor hunting, during a change in motor load, or by non-fundamental component voltages and currents applied by the inverter. These motors are variable speed controlled by the inverter. Common large motor utility and industrial applications are pump and fan drives that are best suited by a variable speed motor. Inverter control of the HTS motor eliminates the need to design the rotor for line starting, which would dump a large amount of heat into the rotor that would then heavily tax the cryogenic cooling system. The field winding is fed by a brushless exciter that provides DC current to the HTS rotor winding. The stator winding is air or water cooled. Technical and commercial hurdles to industrial HTS motor product introduction and customer acceptance include (1) the high cost of HTS wire and the cryogenic cooling system components, (2) customer concerns about reliability of HTS motors, and (3) the ability to attain the loss reduction potential of large HTS motors. Reliance Electric has demonstrated a number of HTS based electric motors up to a 1000 hp, variable speed synchronous motor with an HTS field winding in the year 2000. In 2001 this motor was tested to 1600 hp with a sinusoidal (constant frequency) supply. Figure 1-2 shows the HTS motor on the dynamometer test stand in the Reliance Electric test lab. The extensive test program of the 1000 hp motor successfully demonstrated the technical feasibility of large HTS motors and the basic technologies involved, however the test results did indicate the need for design refinements. In addition, test results served to identify other more fundamental critical technology issues, and revealed the need to continue research efforts in order to improve future HTS motor first cost, reliability, and performa

Shoykhet, B. (Baldor Comp.); Schiferl, R. (Baldor Comp.); Duckworth, R.; Rey, C.M.; Schwenterly, S.W.; Gouge, M.J.

2008-05-01T23:59:59.000Z

15

Electric Motor Remanufacturing and Energy Savings Sahil Sahni1  

E-Print Network [OSTI]

Electric Motor Remanufacturing and Energy Savings Sahil Sahni1 , Avid Boustani1 , Timothy Gutowski to this study. #12;Contents 1 Introduction to Electric Motors 1 1.1 Motor Classifications of Figures 1 Motor System Electricity Consumption by Industrial Sectors (TWh) for 1994. A total of 691

Gutowski, Timothy

16

A University of Alabama Axial-Gap Electric Motor Developmenty  

E-Print Network [OSTI]

CAVT A University of Alabama Axial-Gap Electric Motor Developmenty Research Center OBJECTIVE ­ Develop axial gap permanent-magnet electric Axial motor ­ Develop axial gap permanent-magnet electric motor topologies with high torque and power densities MOTIVATION ­ Axial-gap ("pancake") motors have

Carver, Jeffrey C.

17

Department of Electrical Engineering Fall 2009 Electridyne Motor  

E-Print Network [OSTI]

PENNSTATE Department of Electrical Engineering Fall 2009 Electridyne Motor Overview Our sponsored project was to design an elecrtic motor for an urban transportation vehicle, the challenges involved included research into motor design, consideration of the materials, and the electromagnetic parameters

Demirel, Melik C.

18

Highly Efficient Electric Motor Systems  

E-Print Network [OSTI]

engineering capabilities · Develop & launch products beyond fan & pump applications, i.e. · Electric vehicle performance for same cost Replaces or simplifies mechanical belts, pulleys and gearboxes Delivers 2X torque and Menlo Ventures Low-cost manufacturing automation developed POs received for early products Projected

19

Electric machine for hybrid motor vehicle  

DOE Patents [OSTI]

A power system for a motor vehicle having an internal combustion engine and an electric machine is disclosed. The electric machine has a stator, a permanent magnet rotor, an uncluttered rotor spaced from the permanent magnet rotor, and at least one secondary core assembly. The power system also has a gearing arrangement for coupling the internal combustion engine to wheels on the vehicle thereby providing a means for the electric machine to both power assist and brake in relation to the output of the internal combustion engine.

Hsu, John Sheungchun (Oak Ridge, TN)

2007-09-18T23:59:59.000Z

20

Lagrangean Decomposition Algorithm for Supply Chain Redesign of Electric Motors  

E-Print Network [OSTI]

Lagrangean Decomposition Algorithm for Supply Chain Redesign of Electric Motors Industry Yongheng Redesign of Electric Motors Industry Introduction of the Supply Chain Model 3/22/13 2 Analia Rodriguez #12 Decomposition Algorithm for Supply Chain Redesign of Electric Motors Industry #12;Lagrangean Decomposition

Grossmann, Ignacio E.

Note: This page contains sample records for the topic "4-cylinder electric motor" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


21

Electric Motor Thermal Management for Electric Traction Drives (Presentation)  

SciTech Connect (OSTI)

Thermal constraints place significant limitations on how electric motors ultimately perform. Finite element analysis and computational fluid dynamics modeling approaches are being increasingly utilized in the design and analysis of electric motors. As the models become more sophisticated, it is important to have detailed and accurate knowledge of material thermal properties and convective heat transfer coefficients. In this work, the thermal properties and inter-lamination thermal contact resistances were measured for different stator lamination materials. Also, convective heat transfer coefficients of automatic transmission fluid (ATF) jets were measured to better understand the heat transfer of ATF impinging on motor copper windings. Experiments were carried out at various ATF temperatures and jet velocities to quantify the influence of these parameters on heat transfer coefficients.

Bennion, K.; Cousineau, J.; Moreno, G.

2014-09-01T23:59:59.000Z

22

MIT Electric Vehicle Team Porsche designing a cooling system for the AC24 electric motor  

E-Print Network [OSTI]

In this thesis I worked on the design and analysis of a cooling system for the electric motor of the MIT Electric Vehicle Team's Porsche 914 Battery Electric Vehicle. The vehicle's Azure Dynamics AC24 motor tended to ...

Meenen, Jordan N

2010-01-01T23:59:59.000Z

23

New Energy Efficiency Standards for Electric Motors and Walk...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Motors and Walk-in Coolers and Freezers to Save on Energy Bills and Reduce Carbon Pollution New Energy Efficiency Standards for Electric Motors and Walk-in Coolers and Freezers...

24

Case Studies of High Efficiency Electric Motor Applicability  

E-Print Network [OSTI]

Much has been written about the advantages and disadvantages of high efficiency electric motors. For a given motor application it is possible to find literature that enables a plant engineer to make an informed choice between a standard efficiency...

Wagner, J. R.

25

Advanced Power Electronics and Electric Motors (APEEM) R&D Program...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Electric Motors (APEEM) R&D Program Overview Advnaced Power Electronics and Electric Machines (APEEM) R&D Program Overview Advanced Power Electronics and Electric Motors (APEEM)...

26

Thermal Management of Power Electronics and Electric Motors for Electric-Drive Vehicles (Presentation)  

SciTech Connect (OSTI)

This presentation is an overview of the power electronics and electric motor thermal management and reliability activities at NREL. The focus is on activities funded by the Department of Energy Vehicle Technologies Office Advanced Power Electronics and Electric Motors Program.

Narumanchi, S.

2014-09-01T23:59:59.000Z

27

Reducing current reversal time in electric motor control  

DOE Patents [OSTI]

The time required to reverse current flow in an electric motor is reduced by exploiting inductive current that persists in the motor when power is temporarily removed. Energy associated with this inductive current is used to initiate reverse current flow in the motor.

Bredemann, Michael V

2014-11-04T23:59:59.000Z

28

High Efficiency Fans and High Efficiency Electrical Motors  

E-Print Network [OSTI]

Replacing nominal efficient electrical motors with premium efficiency can save on electrical power costs in cotton gins. Connected horsepower load on industrial air fans is approximately 60% of the total horsepower in a typical cotton gin...

Breedlove, C. W.

29

Summary of electric vehicle dc motor-controller tests  

SciTech Connect (OSTI)

Available performance data for production motors are usually of marginal value to the electric vehicle designer. To provide at least a partial remedy to this situation, tests of typical dc propulsion motors and controllers were conducted as part of the DOE Electric Vehicle Program. The objectives of this program were to evaluate the differences in the performance of dc motors when operating with chopper-type controllers and when operating on direct current; and to gain an understanding of the interactions between the motor and the controller which cause these differences. Toward this end, motor-controller tests performed by the NASA Lewis Research Center provided some of the first published data that quantified motor efficiency variations for both ripple-free (straight dc) and chopper modes of operation. Test and analysis work at the University of Pittsburgh explored motor-controller relationships in greater depth. And to provide additional data, 3E Vehicles tested two small motors, both on a dynamometer and in a vehicle, and the Eaton Corporation tested larger motors, using sophisticated instrumentation and digital processing techniques. All the motors tested were direct-current types. Of the separately excited types, seven were series wound and two were shunt wound. One self-excited permanent magnet type was also tested. Four of the series wound motors used brush shifting to obtain good commutation. In almost all cases, controller limitations constrained the test envelope so that the full capability of the motors could not be explored.

McBrien, E F; Tryon, H B

1982-09-01T23:59:59.000Z

30

Rare-Earth-Free Traction Motor: Rare Earth-Free Traction Motor for Electric Vehicle Applications  

SciTech Connect (OSTI)

REACT Project: Baldor will develop a new type of traction motor with the potential to efficiently power future generations of EVs. Unlike todays large, bulky EV motors which use expensive, imported rare-earth-based magnets, Baldors motor could be light, compact, contain no rare earth materials, and have the potential to deliver more torque at a substantially lower cost. Key innovations in this project include the use of a unique motor design, incorporation of an improved cooling system, and the development of advanced materials manufacturing techniques. These innovations could significantly reduce the cost of an electric motor.

None

2012-01-01T23:59:59.000Z

31

Aging assessment of large electric motors in nuclear power plants  

SciTech Connect (OSTI)

Large electric motors serve as the prime movers to drive high capacity pumps, fans, compressors, and generators in a variety of nuclear plant systems. This study examined the stressors that cause degradation and aging in large electric motors operating in various plant locations and environments. The operating history of these machines in nuclear plant service was studied by review and analysis of failure reports in the NPRDS and LER databases. This was supplemented by a review of motor designs, and their nuclear and balance of plant applications, in order to characterize the failure mechanisms that cause degradation, aging, and failure in large electric motors. A generic failure modes and effects analysis for large squirrel cage induction motors was performed to identify the degradation and aging mechanisms affecting various components of these large motors, the failure modes that result, and their effects upon the function of the motor. The effects of large motor failures upon the systems in which they are operating, and on the plant as a whole, were analyzed from failure reports in the databases. The effectiveness of the industry`s large motor maintenance programs was assessed based upon the failure reports in the databases and reviews of plant maintenance procedures and programs.

Villaran, M.; Subudhi, M. [Brookhaven National Lab., Upton, NY (United States)

1996-03-01T23:59:59.000Z

32

Electric Motor Maintenance & Repair for Long Term Efficiency  

E-Print Network [OSTI]

Energy costs to operate electric motors can be a significant part of an operating budget. For example, a recent survey of California water departments reveals energy costs for pumping and treating water may be 25% of operating costs. Strategies...

Brithinee, W. P.

33

Advanced Power Electronics and Electric Motors Annual Report -- 2013  

SciTech Connect (OSTI)

This report describes the research into advanced liquid cooling, integrated power module cooling, high temperature air cooled power electronics, two-phase cooling for power electronics, and electric motor thermal management by NREL's Power Electronics group in FY13.

Narumanchi, S.; Bennion, K.; DeVoto, D.; Moreno, G.; Rugh, J.; Waye, S.

2015-01-01T23:59:59.000Z

34

Economic Realities and Energy Efficient Polyphase Integral Horsepower Electric Motors  

E-Print Network [OSTI]

Energy efficient polyphase integral horsepower electric motors are currently being vigorously promoted as a profitable method of conserving energy in many industrial and commercial applications. While the goal to be attained is indeed laudable...

Whittington, B. W.

1980-01-01T23:59:59.000Z

35

Efficient, High-Torque Electric Vehicle Motor: Advanced Electric Vehicle Motors with Low or No Rare Earth Content  

SciTech Connect (OSTI)

REACT Project: QM Power will develop a new type of electric motor with the potential to efficiently power future generations of EVs without the use of rare-earth-based magnets. Many of todays EV motors use rare earth magnets to efficiently provide torque to the wheels. QM Powers motors would contain magnets that use no rare earth minerals, are light and compact, and can deliver more power with greater efficiency and at reduced cost. Key innovations in this project include a new motor design with iron-based magnetic materials, a new motor control technique, and advanced manufacturing techniques that substantially reduce the cost of the motor. The ultimate goal of this project is to create a cost-effective EV motor that offers the rough peak equivalent of 270 horsepower.

None

2012-01-01T23:59:59.000Z

36

High-speed electrical motor evaluation  

SciTech Connect (OSTI)

Under this task, MTI conducted a general review of state-of-the-art high-speed motors. The purpose of this review was to assess the operating parameters, limitations and performance of existing motor designs, and to establish commercial sources for a motor compatible with the requirements of the Brayton-cycle system. After the motor requirements were established, a list of motor types, manufacturers and designs capable of achieving the requisite performance was compiled. This list was based on an in-house evaluation of designs. Following the establishment of these options, a technical evaluation of the designs selected was conducted. In parallel with their evaluations, MTI focused on the establishment of commercial sources.

Not Available

1989-02-03T23:59:59.000Z

37

System and method to determine electric motor efficiency nonintrusively  

DOE Patents [OSTI]

A system and method for nonintrusively determining electric motor efficiency includes a processor programed to, while the motor is in operation, determine a plurality of stator input currents, electrical input data, a rotor speed, a value of stator resistance, and an efficiency of the motor based on the determined rotor speed, the value of stator resistance, the plurality of stator input currents, and the electrical input data. The determination of the rotor speed is based on one of the input power and the plurality of stator input currents. The determination of the value of the stator resistance is based on at least one of a horsepower rating and a combination of the plurality of stator input currents and the electrical input data. The electrical input data includes at least one of an input power and a plurality of stator input voltages.

Lu, Bin (Kenosha, WI); Habetler, Thomas G. (Snellville, GA); Harley, Ronald G. (Lawrenceville, GA)

2011-08-30T23:59:59.000Z

38

Electric motor systems in developing countries: Opportunities for efficiency improvement  

SciTech Connect (OSTI)

This report presents an overview of the current status and efficiency improvement potential of industrial motor systems in developing countries. Better management of electric motor systems is of particular relevance in developing countries, where improved efficiency can lead to increased productivity and slower growth in electricity demand. Motor systems currently consume some 65--80% of the industrial electricity in developing countries. Drawing on studies from Thailand, India, Brazil, China, Pakistan, and Costa Rica, we describe potential efficiency gains in various parts of the motor system, from the electricity delivery system through the motor to the point where useful work is performed. We report evidence of a significant electricity conservation potential. Most of the efficiency improvement methods we examine are very cost-effective from a societal viewpoint, but are generally not implemented due to various barriers that deter their adoption. Drawing on experiences in North America, we discuss a range of policies to overcome these barriers, including education, training, minimum efficiency standards, motor efficiency testing protocols, technical assistance programs, and financial incentives.

Meyers, S.; Monahan, P.; Lewis, P.; Greenberg, S. [Lawrence Berkeley Lab., CA (United States); Nadel, S. [American Council for an Energy-Efficient Economy, Washington, DC (United States)

1993-08-01T23:59:59.000Z

39

Computational analysis of temperature rise phenomena in electric induction motors  

E-Print Network [OSTI]

Computational analysis of temperature rise phenomena in electric induction motors Ying Huai Institute, University of Southern Denmark, Grundvigs Alle 150, Sonderborg, DK-6400, Denmark c Danfoss Drives A/S, Denmark Received 12 October 2002; accepted 20 December 2002 Abstract In developing electric

Melnik, Roderick

40

BILATERAL HINDLIMB MOVEMENT AND MOTOR PATTERNS EVOKED BY ELECTRICAL MICROSTIMULATION IN THE VENTROLATERAL FUNICULUS  

E-Print Network [OSTI]

BILATERAL HINDLIMB MOVEMENT AND MOTOR PATTERNS EVOKED BY ELECTRICAL MICROSTIMULATION motor patterns during electrical stimulation, these DLF tracts are also necessary for normal voluntary movements in right and left hindlimbs in response to unilateral electrical stimulation of sites

Stanley, B. Glenn

Note: This page contains sample records for the topic "4-cylinder electric motor" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


41

Hybrid Cascaded H-bridges Multilevel Motor Drive Control for Electric Vehicles  

E-Print Network [OSTI]

Hybrid Cascaded H-bridges Multilevel Motor Drive Control for Electric Vehicles Zhong Du1 , Leon M vehicle motor drive applications and hybrid electric vehicle motor drive applications. Keywords: hybrid cascaded H-bridge multilevel converter, DC voltage balance control, multilevel motor drive, electric

Tolbert, Leon M.

42

System and method to determine electric motor efficiency using an equivalent circuit  

DOE Patents [OSTI]

A system and method for determining electric motor efficiency includes a monitoring system having a processor programmed to determine efficiency of an electric motor under load while the electric motor is online. The determination of motor efficiency is independent of a rotor speed measurement. Further, the efficiency is based on a determination of stator winding resistance, an input voltage, and an input current. The determination of the stator winding resistance occurs while the electric motor under load is online.

Lu, Bin (Kenosha, WI); Habetler, Thomas G. (Snellville, GA)

2011-06-07T23:59:59.000Z

43

Heat engine and electric motor torque distribution strategy for a hybrid electric vehicle  

DOE Patents [OSTI]

A method is provided for controlling a power train system for a hybrid electric vehicle. The method includes a torque distribution strategy for controlling the engine and the electric motor. The engine and motor commands are determined based upon the accelerator position, the battery state of charge and the amount of engine and motor torque available. The amount of torque requested for the engine is restricted by a limited rate of rise in order to reduce the emissions from the engine. The limited engine torque is supplemented by motor torque in order to meet a torque request determined based upon the accelerator position.

Boberg, Evan S. (Hazel Park, MI); Gebby, Brian P. (Hazel Park, MI)

1999-09-28T23:59:59.000Z

44

A Detailed Analysis of the Nonlinear Dynamics of the Electric Step Motor J. Reiss, F. Alin*  

E-Print Network [OSTI]

A Detailed Analysis of the Nonlinear Dynamics of the Electric Step Motor J. Reiss, F. Alin* , M.robert@univ-reims.fr Abstract The electric step motor is an electromechanical device which converts electrical pulses of stationarity in the system. We show that the electric step motor may function as a low-dimensional chaotic

Reiss, Josh

45

Electric Motor Thermal Management R&D (Presentation)  

SciTech Connect (OSTI)

Thermal constraints place significant limitations on how electric motors ultimately perform. Without the ability to remove heat, the motor cannot operate without sacrificing performance, efficiency, and reliability. Finite element analysis and computational fluid dynamics modeling approaches are being increasingly utilized in the design and analysis of electric motors. As the models become more sophisticated, it is important to have detailed and accurate knowledge of both the passive thermal performance and the active cooling performance. In this work, we provide an overview of research characterizing both passive and active thermal elements related to electric motor thermal management. To better characterize the passive thermal performance, the effective thermal properties and inter-lamination thermal contact resistances were measured for different stator lamination materials. The active cooling performance of automatic transmission fluid (ATF) jets was also measured to better understand the heat transfer coefficients of ATF impinging on motor copper windings. Ford's Mercon LV was the ATF evaluated in this study. The presentation provides an overview of prior work with a focus on describing future plans for research to be performed during FY15.

Bennion, K.

2014-11-01T23:59:59.000Z

46

IEMDC IN-LINE ELECTRIC MOTOR DRIVEN COMPRESSOR  

SciTech Connect (OSTI)

This report contains the final project summary and deliverables required by the award for the development of an In-line Electric Motor Driven Compressor (IEMDC). Extensive work was undertaken during the course of the project to develop the motor and the compressor section of the IEMDC unit. Multiple design iterations were performed to design an electric motor for operation in a natural gas environment and to successfully integrate the motor with a compressor. During the project execution, many challenges were successfully overcome in order to achieve the project goals and to maintain the system design integrity. Some of the challenges included limiting the magnitude of the compressor aerodynamic loading for appropriate sizing of the magnetic bearings, achieving a compact motor rotor size to meet the rotor dynamic requirements of API standards, devising a motor cooling scheme using high pressure natural gas, minimizing the impact of cooling on system efficiency, and balancing the system thrust loads for the magnetic thrust bearing. Design methods that were used on the project included validated state-of-the-art techniques such as finite element analysis and computational fluid dynamics along with the combined expertise of both Curtiss-Wright Electro-Mechanical Corporation and Dresser-Rand Company. One of the most significant areas of work undertaken on the project was the development of the unit configuration for the system. Determining the configuration of the unit was a significant step in achieving integration of the electric motor into a totally enclosed compression system. Product review of the IEMDC unit configuration was performed during the course of the development process; this led to an alternate design configuration. The alternate configuration is a modular design with the electric motor and compressor section each being primarily contained in its own pressure containing case. This new concept resolved the previous conflict between the aerodynamic flow passage requirements and electric motor requirements for support and utilities by bounding the flowpath within the compressor section. However most importantly, the benefits delivered by the new design remained the same as those proposed by the goals of the project. In addition, this alternate configuration resulted in the achievement of a few additional advantages over the original concept such as easier maintenance, operation, and installation. Interaction and feedback solicited from target clients regarding the unit configuration supports the fact that the design addresses industry issues regarding accessibility, maintainability, preferred operating practice, and increased reliability.

Michael J. Crowley; Prem N. Bansal

2004-10-01T23:59:59.000Z

47

Oil Field Electrical Energy Savings Through Energy-Efficient Motor Retrofits  

E-Print Network [OSTI]

The Wyoming Electric Motor Training and Testing Center (WEMTTC), in conjunction with the Department of Energy-Denver Support Office and the Naval Petroleum Reserve #3 (NPR-3), has conducted an extensive study of electric motor efficiency...

Ula, S.; Bershinsky, V.; Cain, W.

48

Manufacturing Equipment Modeling For a linear axis actuated by an electric motor complete the following  

E-Print Network [OSTI]

Manufacturing Equipment Modeling QUESTION 1 For a linear axis actuated by an electric motor(t). Include the axis disturbance force, but do not include motor electrical dynamics or Coulomb friction For a spindle actuated by an electric motor complete the following: a. Derive a differential equation

Landers, Robert G.

49

Lagrangean Decomposition Algorithm for Supply Chain Redesign in Electric Motors Industry  

E-Print Network [OSTI]

2013/8/1 1 Lagrangean Decomposition Algorithm for Supply Chain Redesign in Electric Motors Industry of Automation Lagrangean Decomposition Algorithm for Supply Chain Redesign of Electric Motors Industry Redesign of Electric Motors Industry Institute of Process Control and Engineering, Department

Grossmann, Ignacio E.

50

Electric Motor Drive Selection Issues for HEV Propulsion Systems: A Comparative Study  

E-Print Network [OSTI]

Electric Motor Drive Selection Issues for HEV Propulsion Systems: A Comparative Study M. Zeraoulia1 Combustion Engine (ICE) and the electric motor to deliver power in parallel to drive the wheels. Since both the ICE and electric motor are generally coupled to the drive shaft of the wheels via two clutches

Paris-Sud XI, Université de

51

Electric Vehicle Induction Motor DSVM-DTC with Torque Ripple Minimization  

E-Print Network [OSTI]

Electric Vehicle Induction Motor DSVM-DTC with Torque Ripple Minimization Farid Khoucha1 a sensorless DSVM-DTC of an induction motor that propels an electrical vehicle or a hybrid one. The drive uses, as demonstrated in experimental results. Keywords: Electric vehicle (EV), induction motor, Discrete Space Vector

Paris-Sud XI, Universit de

52

Control of a Fuel-Cell Powered DC Electric Vehicle Motor  

E-Print Network [OSTI]

Control of a Fuel-Cell Powered DC Electric Vehicle Motor Federico Zenith Sigurd Skogestad of a Fuel-Cell Powered DC Electric Vehicle Motor #12;3 Currently Available Models and Control Strategies Skogestad, Control of a Fuel-Cell Powered DC Electric Vehicle Motor #12;3 Currently Available Models

Skogestad, Sigurd

53

A Power Presizing Methodology for Electric Vehicle Traction Motors Bekheira Tabbache1,2  

E-Print Network [OSTI]

A Power Presizing Methodology for Electric Vehicle Traction Motors Bekheira Tabbache1,2 , Sofiane for presizing the power of an electric vehicle traction motor. Based on the vehicle desired performances motor, power presizing, driving cycle. Nomenclature EV = Electric Vehicle; V = Vehicle speed; Vb

Paris-Sud XI, Université de

54

Design and Control of the Induction Motor Propulsion of an Electric Vehicle  

E-Print Network [OSTI]

Design and Control of the Induction Motor Propulsion of an Electric Vehicle B. Tabbache1,2 , A for presizing the induction motor propulsion of an Electric Vehicle (EV). Based on the EV desired performances for different induction motor-based EVs using a siding mode control technique. Index Terms--Electric Vehicle (EV

Brest, Université de

55

Electrical motor/generator drive apparatus and method  

DOE Patents [OSTI]

The present disclosure includes electrical motor/generator drive systems and methods that significantly reduce inverter direct-current (DC) bus ripple currents and thus the volume and cost of a capacitor. The drive methodology is based on a segmented drive system that does not add switches or passive components but involves reconfiguring inverter switches and motor stator winding connections in a way that allows the formation of multiple, independent drive units and the use of simple alternated switching and optimized Pulse Width Modulation (PWM) schemes to eliminate or significantly reduce the capacitor ripple current.

Su, Gui Jia

2013-02-12T23:59:59.000Z

56

Advanced Power Electronics and Electric Motors (APEEM) R&D Program...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Documents & Publications Advanced Power Electronics and Electric Motors (APEEM) R&D Program Overview Advnaced Power Electronics and Electric Machines (APEEM) R&D Program Overview...

57

Instrument for analysis of electric motors based on slip-poles component  

DOE Patents [OSTI]

A new instrument is described for monitoring the condition and speed of an operating electric motor from a remote location. The slip-poles component is derived from a motor current signal. The magnitude of the slip-poles component provides the basis for a motor condition monitor, while the frequency of the slip-poles component provides the basis for a motor speed monitor. The result is a simple-to-understand motor health monitor in an easy-to-use package. Straightforward indications of motor speed, motor running current, motor condition (e.g., rotor bar condition) and synthesized motor sound (audible indication of motor condition) are provided. With the device, a relatively untrained worker can diagnose electric motors in the field without requiring the presence of a trained engineer or technician. 4 figs.

Haynes, H.D.; Ayers, C.W.; Casada, D.A.

1996-11-26T23:59:59.000Z

58

Instrument for analysis of electric motors based on slip-poles component  

DOE Patents [OSTI]

A new instrument for monitoring the condition and speed of an operating electric motor from a remote location. The slip-poles component is derived from a motor current signal. The magnitude of the slip-poles component provides the basis for a motor condition monitor, while the frequency of the slip-poles component provides the basis for a motor speed monitor. The result is a simple-to-understand motor health monitor in an easy-to-use package. Straightforward indications of motor speed, motor running current, motor condition (e.g., rotor bar condition) and synthesized motor sound (audible indication of motor condition) are provided. With the device, a relatively untrained worker can diagnose electric motors in the field without requiring the presence of a trained engineer or technician.

Haynes, Howard D. (Knoxville, TN); Ayers, Curtis W. (Clinton, TN); Casada, Donald A. (Knoxville, TN)

1996-01-01T23:59:59.000Z

59

1756 IEEE TRANSACTIONS ON VEHICULAR TECHNOLOGY, VOL. 55, NO. 6, NOVEMBER 2006 Electric Motor Drive Selection Issues for HEV  

E-Print Network [OSTI]

1756 IEEE TRANSACTIONS ON VEHICULAR TECHNOLOGY, VOL. 55, NO. 6, NOVEMBER 2006 Electric Motor Drive--Comparison, electric propulsion, hybrid electric vehicle (HEV). I. INTRODUCTION SELECTION of traction motors for hybrid of electric motors adopted or under serious consideration for HEVs as well as for EVs include the dc motor

60

United States Industrial Electric Motor Systems Market Opportunities...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

for Industry MotorMaster+ User Manual New Motor Systems Market Assessment AMO and LBNL are currently developing an update to the original Motor Systems Market Assessment. The...

Note: This page contains sample records for the topic "4-cylinder electric motor" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


61

Electric Field Driven Torque in Biological Rotary Motors  

E-Print Network [OSTI]

Ion driven rotary motors, such as Fo-ATP synthase (Fo) and the bacterial flagellar motor, act much like a battery-powered electric motor. They convert energy from ions as they move from high to low potential across a membrane into torque and rotary motion. Here we propose a mechanism whereby electric fields, emanating from channels in one or more stators, act on asymmetric charge distributions due to protonated and deprotonated sites in the rotor and drive it to rotate. The model predicts an ideal scaling law between torque and ion motive force, which can be hindered by mitochondrial mutations. The rotor of Fo drives the gamma-subunit to rotate within the ATP-producing complex (F1), working against an opposing torque that rises and falls periodically with angular position. Drawing an analogy with Brownian motion of a particle in a tilted washboard potential, we compute the highly nonlinear ATP production rate vs. proton motive force (pmf), showing a minimum pmf needed to drive ATP production with important me...

Miller,, John H; Maric, Sladjana; Infante, Hans L; Claycomb, James R

2013-01-01T23:59:59.000Z

62

Achieving A Long Term Business Impact by Improving the Energy Effectiveness and Reliability of Electric Motors  

E-Print Network [OSTI]

Over 100,000 electric motors drive the production equipment throughout a large chemical company. The energy-efficiency and reliability of these motors during their entire life have a decided impact on the company's manufacturing costs and production...

Whelan, C. D.

63

PWM Inverter-Fed Induction Motor-Based Electrical Vehicles Fault-Tolerant Control  

E-Print Network [OSTI]

PWM Inverter-Fed Induction Motor-Based Electrical Vehicles Fault-Tolerant Control Bekhera Tabbache proposes a fault-tolerant control scheme for PWM inverter-fed induction motor-based electric vehicles and simulations on an electric vehicle are carried-out using a European urban driving cycle to assess the FTC

Paris-Sud XI, Universit de

64

SDTC-EKF Control of an Induction Motor Based Electric Vehicle B. Tabbache1,2  

E-Print Network [OSTI]

SDTC-EKF Control of an Induction Motor Based Electric Vehicle B. Tabbache1,2 , A. Kheloui2 , M torque control of an induction motor based electric vehicle. In this case, stator flux and rotational for an electric vehicle control. Keywords: Sensorless Direct Torque Control (SDTC), Extented Kalman Filter (EKF

Paris-Sud XI, Universit de

65

Independent Control of Two Induction Motors Fed by a Five Legs PWM Inverter for Electric Vehicles  

E-Print Network [OSTI]

Independent Control of Two Induction Motors Fed by a Five Legs PWM Inverter for Electric Vehicles B. NOMENCLATURE EV = Electric vehicle; IM = Induction motor; IFOC = Indirect field oriented control; PWM= Pulse force; Fcr = Climbing and downgrade resistance force; Pv = Vehicle driving power; J = Total inertia

Boyer, Edmond

66

Method and system for operating an electric motor  

DOE Patents [OSTI]

Methods and systems for operating an electric motor having a plurality of windings with an inverter having a plurality of switches coupled to a voltage source are provided. A first plurality of switching vectors is applied to the plurality of switches. The first plurality of switching vectors includes a first ratio of first magnitude switching vectors to second magnitude switching vectors. A direct current (DC) current associated with the voltage source is monitored during the applying of the first plurality of switching vectors to the plurality of switches. A second ratio of the first magnitude switching vectors to the second magnitude switching vectors is selected based on the monitoring of the DC current associated with the voltage source. A second plurality of switching vectors is applied to the plurality of switches. The second plurality of switching vectors includes the second ratio of the first magnitude switching vectors to the second magnitude switching vectors.

Gallegos-Lopez, Gabriel; Hiti, Silva; Perisic, Milun

2013-01-22T23:59:59.000Z

67

Submerged electricity generation plane with marine current-driven motors  

DOE Patents [OSTI]

An underwater apparatus for generating electric power from ocean currents and deep water tides. A submersible platform including two or more power pods, each having a rotor with fixed-pitch blades, with drivetrains housed in pressure vessels that are connected by a transverse structure providing buoyancy, which can be a wing depressor, hydrofoil, truss, or faired tube. The platform is connected to anchors on the seafloor by forward mooring lines and a vertical mooring line that restricts the depth of the device in the water column. The platform operates using passive, rather than active, depth control. The wing depressor, along with rotor drag loads, ensures the platform seeks the desired operational current velocity. The rotors are directly coupled to a hydraulic pump that drives at least one constant-speed hydraulic-motor generator set and enables hydraulic braking. A fluidic bearing decouples non-torque rotor loads to the main shaft driving the hydraulic pumps.

Dehlsen, James G.P.; Dehlsen, James B.; Fleming, Alexander

2014-07-01T23:59:59.000Z

68

System and method for motor speed estimation of an electric motor  

DOE Patents [OSTI]

A system and method for a motor management system includes a computer readable storage medium and a processing unit. The processing unit configured to determine a voltage value of a voltage input to an alternating current (AC) motor, determine a frequency value of at least one of a voltage input and a current input to the AC motor, determine a load value from the AC motor, and access a set of motor nameplate data, where the set of motor nameplate data includes a rated power, a rated speed, a rated frequency, and a rated voltage of the AC motor. The processing unit is also configured to estimate a motor speed based on the voltage value, the frequency value, the load value, and the set of nameplate data and also store the motor speed on the computer readable storage medium.

Lu, Bin (Kenosha, WI); Yan, Ting (Brookfield, WI); Luebke, Charles John (Sussex, WI); Sharma, Santosh Kumar (Viman Nagar, IN)

2012-06-19T23:59:59.000Z

69

Sensor Fault-Tolerant Control of an Induction Motor Based Electric Vehicle Bekhera Tabbache1,2  

E-Print Network [OSTI]

Sensor Fault-Tolerant Control of an Induction Motor Based Electric Vehicle Bekhera Tabbache1://www.lbms.fr Keywords Electric Vehicle (EV), Induction motor, Sensor fault, Fault-tolerant control (FTC), Direct torque a reconfigurable direct torque control of an induction motor-based electric vehicle. The proposed strategy concerns

Paris-Sud XI, Universit de

70

Extended cage adjustable speed electric motors and drive packages  

DOE Patents [OSTI]

The rotor cage of a motor is extended, a second stator is coupled to this extended rotor cage, and the windings have the same number of poles. The motor torque and speed can be controlled by either injecting energy into or extracting energy out from the rotor cage. The motor produces less harmonics than existing doubly-fed motors. Consequently, a new type of low cost, high efficiency drive is produced. 12 figs.

Hsu, J.S.

1999-03-23T23:59:59.000Z

71

Extended cage adjustable speed electric motors and drive packages  

DOE Patents [OSTI]

The rotor cage of a motor is extended, a second stator is coupled to this extended rotor cage, and the windings have the same number of poles. The motor torque and speed can be controlled by either injecting energy into or extracting energy out from the rotor cage. The motor produces less harmonics than existing doubly-fed motors. Consequently, a new type of low cost, high efficiency drive is produced.

Hsu, John S. (Oak Ridge, TN)

1999-01-01T23:59:59.000Z

72

Intelligent Power Assist Algorithms for Electric Bicycles  

E-Print Network [OSTI]

electric hub motor . . . . . . . . . . . . . . . . . . .Golden Motor electric bicycle model MT-Electric hub motor in the front

Fan, Xuan

2010-01-01T23:59:59.000Z

73

ECE 331 Electromechanical Energy Conversion Catalog Description: Energy conversion principles for electric motors. Steady-state  

E-Print Network [OSTI]

. Introduction to drives and power electronics in control of electric machines, including switch-mode PWM (ABET Outcomes A, C, E, j, k) Learning Resources: Electric Machines and Drives: A First Course, Ned for electric motors. Steady-state characteristics and analysis of induction, synchronous and direct current

74

Design and manufacture of a chain driven motor shaft for Formula Electric applications  

E-Print Network [OSTI]

This document describes the design, manufacture, and testing of a motor shaft assembly that is a subcomponent of the drivetrain system in a Formula Electric racecar. The design covers detailed analysis of the bearing, ...

Wanderman, Jack J. (Jack Joseph)

2013-01-01T23:59:59.000Z

75

The Wanlass Polyphase Rotating Magnetic Device in Electric Motor and Induction Generator Applications  

E-Print Network [OSTI]

The electric motor in its present technological configuration has remained virtually unchanged since its original conception nearly 100 years ago. It would be logical to assume that a device, which has undergone such insignificant evolution, would...

Asp, D. E.

1984-01-01T23:59:59.000Z

76

Comparative analysis of electrical and mechanical fault signatures in induction motors  

E-Print Network [OSTI]

of interest. Due to its cost-effective nature and ease of use, electrical sensors are preinstalled at the motor switchgear by manufacturers. However in order to achieve this for mechanical faults, a systematic comparison between the vibration signatures...

Venugopal, Arvind Madabushi

2005-02-17T23:59:59.000Z

77

DATE : NVLAP LAB CODE: NVLAP EFFICIENCY OF ELECTRIC MOTORS APPLICATION (REV. 2013-06-11) PAGE 1 OF 1  

E-Print Network [OSTI]

DATE : NVLAP LAB CODE: NVLAP EFFICIENCY OF ELECTRIC MOTORS APPLICATION (REV. 2013-06-11) PAGE 1 OF 1 EFFICIENCY OF ELECTRIC MOTORS TEST METHOD SELECTION LIST Instructions: Check each test method01* IEEE 112 Method B Test Procedure for Polyphase Induction Motors and Generators (for accreditation

78

Vibrissa Movement Elicited by Rhythmic Electrical Microstimulation to Motor Cortex in the Aroused Rat Mimics Exploratory Whisking  

E-Print Network [OSTI]

Vibrissa Movement Elicited by Rhythmic Electrical Microstimulation to Motor Cortex in the Aroused elicited by rhythmic electrical microstimulation to motor cortex in the aroused rat mimics exploratory.2003. The rhythmic motor activity of the vibrissae that rodents use for the tactile local- ization of objects

Kleinfeld, David

79

Ameren Illinois (Electric)- Custom, HVAC, and Motor Business Efficiency Incentives  

Broader source: Energy.gov [DOE]

Prescriptive rebates are available for many HVAC and motor efficiency improvements. Pre-approval is required for all rebates. The programs are available only to non-residential customers that...

80

Ultra-Efficient and Power Dense Electric Motors for U. S. Industry  

SciTech Connect (OSTI)

The primary purpose of this project was to combine the ease-of-installation and ease-of-use attributes of industrial induction motors with the low-loss and small size and weight advantages of PM motors to create an ultra-efficient, high power density industrial motor that can be started across-the-line or operated from a standard, Volts/Hertz drive without the need for a rotor position feedback device. PM motor products that are currently available are largely variable speed motors that require a special adjustable speed drive with rotor position feedback. The reduced size and weight helps to offset the magnet cost in order make these motors commercially viable. The scope of this project covers horsepower ratings from 20 ? 500. Prototypes were built and tested at ratings ranging from 30 to 250 HP. Since fans, pumps and compressors make up a large portion of industrial motor applications, the motor characteristics are tailored to those applications. Also, since there is extensive use of adjustable frequency inverters in these applications, there is the opportunity to design for an optimal pole number and operate at other than 60 Hz frequency when inverters are utilized. Designs with four and eight pole configurations were prototyped as part of this work. Four pole motors are the most commonly used configuration in induction motors today. The results of the prototype design, fabrication, and testing were quite successful. The 50 HP rating met all of the design goals including efficiency and power density. Tested values of motor losses at 50 HP were 30% lower than energy efficient induction motors and the motor weight is 35% lower than the energy efficient induction motor of the same rating. Further, when tested at the 30 HP rating that is normally built in this 286T frame size, the efficiency far exceeds the project design goals with 30 HP efficiency levels indicating a 55% reduction in loss compared to energy efficient motors with a motor weight that is a few percentage points lower than the energy efficient motor. This 30 HP rating full load efficiency corresponds to a 46% reduction in loss compared to a 30 HP NEMA Premium? efficient motor. The cost goals were to provide a two year or shorter efficiency-based payback of a price premium associated with the magnet cost in these motors. That goal is based on 24/7 operation with a cost of electricity of 10 cents per kW-hr. Similarly, the 250 HP prototype efficiency testing was quite successful. In this case, the efficiency was maximized with a slightly less aggressive reduction in active material. The measured full load efficiency of 97.6% represents in excess of a 50% loss reduction compared to the equivalent NEMA Premium Efficiency induction motor. The active material weight reduction was a respectable 14.5% figure. This larger rating demonstrated both the scalability of this technology and also the ability to flexibly trade off power density and efficiency. In terms of starting performance, the 30 ? 50 HP prototypes were very extensively tested. The demonstrated capability included the ability to successfully start a load with an inertia of 25 times the motor?s own inertia while accelerating against a load torque following a fan profile at the motor?s full nameplate power rating. This capability will provide very wide applicability of this motor technology. The 250 HP prototype was also tested for starting characteristics, though without a coupled inertia and load torque. As a result it was not definitively proven that the same 25 times the motor?s own inertia could be started and synchronized successfully at 250 HP. Finite element modeling implies that this load could be successfully started, but it has not yet been confirmed by a test.

Melfi, Michael J.; Schiferl, Richard F.; Umans, Stephen D.

2013-03-12T23:59:59.000Z

Note: This page contains sample records for the topic "4-cylinder electric motor" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


81

Control of a Fuel-Cell Powered DC Electric Vehicle Motor Federico Zenith  

E-Print Network [OSTI]

Control of a Fuel-Cell Powered DC Electric Vehicle Motor Federico Zenith Sigurd Skogestad Introduction Research in fuel cells receives currently a lot of interest. Fuel cells can be used, in different. However, the dynamics of fuel cells has received comparatively less attention. Control of fuel cells

Skogestad, Sigurd

82

Electric motor/controller design tradeoffs for noise, weight, and efficiency  

SciTech Connect (OSTI)

It is common for an AUV [Autonomous Underwater Vehicle] designer to be put in the position of a subsystem hardware integrator. In the case of electric motors and controllers this may be more by necessity than choice because a suitable subsystems supplier cannot be found. As a result, motors and controllers are purchased from various manufacturers who may optimize the design of each part but hold system performance secondary in importance. Unlike hydraulics, an electric motor/controller system presents significant opportunities to improve noise, weight, and efficiency. But, these opportunities can best be recognized by a single source who not only understands the technology but has the ability to implement them in the development and manufacture of the product. An analysis is presented which explains the various design considerations of noise, weight and efficiency of electric motors and controllers for submersible AUV`s. In concert with the design considerations, their interrelationships are discussed as to how they affect each other in the overall optimization of the system. In conclusion, a matrix is created which shows how the resultant system parameters of noise, weight, and efficiency may be ``traded off`` to tailor the best overall system for the application. 1 ref.

Kopp, N.L.; Brown, G.W.

1994-12-31T23:59:59.000Z

83

Electric Motors and Critical Materials | Department of Energy  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious Rank EERE:Year in Review: TopEnergyIDIQ Contract ESPC IDIQEnergyGovernment Officials.Electric

84

EV Everywhere Grand Challenge - Electric Motors and Critical Materials Breakout  

Broader source: Energy.gov (indexed) [DOE]

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May Jun Jul(Summary) "ofEarly Career Scientists'Montana.Program - LibbyofThisStatement Tuesday, September 25- 7/20/2012 Electric

85

Electrical Motor Drive Apparatus and Method - Energy Innovation Portal  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr MayAtmospheric Optical Depth7-1D: Vegetation Proposed NewcatalystNeutronEnvironmentZIRKLEEFFECTS OFElaineElectric826

86

Motors  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr MayAtmospheric Optical Depth7-1D: VegetationEquipment SurfacesResource ProgramModification andinterface1 EEnergy, OfficeMotors Sign In

87

Not a Babe in the Woods: Using MotorMaster Software to Make Sophisticated Electric Motor Purchase Decisions  

E-Print Network [OSTI]

-Frmne, vertic;1l shaft and C-Face motors are also included in the database. The MotorMaster database can resolve m;my questions about the price commercially available motors. Here are some findings: * Although there is a general... horsepower. synchronous speed, enclosure type and vollIlge rating ;md whether you want a special feature, such as U-Frmne, vertical shaft, or C-Face motors. MotorMaster quickly supplies a list of commercially available models from seventeen manufacturers...

Litman, T.

88

Premium Efficient Motors  

E-Print Network [OSTI]

Premium efficient motors are available which convert electrical energy into mechanical energy with fewer losses than the more standard motors. The fewer losses in these motors are due to changes in the motor design and improved manufacturing methods...

Moser, P. R.

1984-01-01T23:59:59.000Z

89

Report on the feasibility study for improving electric motor service centers in Ghana  

SciTech Connect (OSTI)

On March 3 and 4, 1998, a visit was made to Oak Ridge National Laboratory (ORNL) by two officials from Ghana: Mr. I.K. Mintah, Acting Executive Director, Technical Wing, Ministry of Mines and Energy (MOME) and Dr. A.K. Ofosu-Ahenkorah, Coordinator, Energy Efficiency and Conservation Program, MOME. As a result of this visit, Dr. John S. Hsu of ORNL was invited by MOME to visit the Republic of Ghana in order to study the feasibility of improving electric motor service centers in Ghana.

Hsu, J.S.; Jallouk, P.A.; Staunton, R.H.

1999-12-10T23:59:59.000Z

90

Study of the Advantages of Internal Permanent Magnet Drive Motor with Selectable Windings for Hybrid-Electric Vehicles  

SciTech Connect (OSTI)

This report describes research performed on the viability of changing the effectively active number of turns in the stator windings of an internal permanent magnet (IPM) electric motor to strengthen or weaken the magnetic fields in order to optimize the motor's performance at specific operating speeds and loads. Analytical and simulation studies have been complemented with research on switching mechanisms to accomplish the task. The simulation studies conducted examine the power and energy demands on a vehicle following a series of standard driving cycles and the impact on the efficiency and battery size of an electrically propelled vehicle when it uses an IPM motor with turn-switching capabilities. Both full driving cycle electric propulsion and propulsion limited starting from zero to a set speed have been investigated.

Otaduy, P.J.; Hsu, J.S.; Adams, D.J.

2007-11-30T23:59:59.000Z

91

The United States Industrial Electric Motor Systems Market Opportunities Assessment: Key Results  

E-Print Network [OSTI]

portrait of the inventory of motor systems currently in use in US industrial facilities, estimate motor system energy use and potential for energy savings. The research and analysis to support these objectives consisted primarily of on-site motor system...

Rosenberg, M.

92

Motor torque compensation of an induction electric motor by adjusting a slip command during periods of supposed change in motor temperature  

SciTech Connect (OSTI)

The present invention maintains constant torque in an inverter driven AC induction motor during variations in rotor temperature. It is known that the torque output of a given AC induction motor is dependent upon rotor temperature. At rotor temperatures higher than the nominal operating condition the rotor impedance increases, reducing the rotor current and motor torque. In a similar fashion, the rotor impedance is reduced resulting in increased rotor current and motor torque when the rotor temperature is lower than the nominal operating condition. The present invention monitors the bus current from the DC supply to the inverter and adjusts the slip frequency of the inverter drive to maintain a constant motor torque. This adjustment is based upon whether predetermined conditions implying increased rotor temperature or decreased rotor temperature exist for longer that a predetermined interval of time.

Kelledes, William L. (Brighton, MI); St. John, Don K. (Livonia, MI)

1992-01-01T23:59:59.000Z

93

A Simple Algorithm for Closed-Loop Control of Stepping Motors IEE Proc. -Electr. Power Appl., (1995) Vol 142, No 1, pp 5-13.  

E-Print Network [OSTI]

A Simple Algorithm for Closed-Loop Control of Stepping Motors IEE Proc. - Electr. Power Appl of Reading Whiteknights PO Box 225 Reading RG6 2AY ABSTRACT Stepping motors are normally operated without feedback. A simple control algorithm is developed which allows a stepping motor to operate effectively

Grimbleby, James

94

Efficient electric motor systems for industry. Report on roundtable discussions of market problems and ways to overcome them  

SciTech Connect (OSTI)

Improving the efficiency of electric motor systems is one of the best energy-saving opportunities for the United States. The Department of Energy (DOE) Office of Industrial Technologies estimates that by the year 2010 in the industrial sector, the opportunities for savings from improved efficiency in electric motor systems could be roughly as follows: 240 billion kilowatthours per year. $13 billion per year from US industry`s energy bill. Up to 50,000 megawatts in new powerplant capacity avoided. Up to 44 million metric tons of carbon-equivalent emissions mitigated per year, corresponding to 3 percent of present US emissions. Recognizing the benefits of this significant opportunity for energy savings, DOE has targeted improvements in the efficiency of electric motor systems as a key initiative in the effort to promote flexibility and efficiency in the way electricity is produced and used. Efficient electric motor systems will help the United States reach its national goals for energy savings and greenhouse gas emission reductions.

Not Available

1993-11-01T23:59:59.000Z

95

A Soft-Switching Inverter for High-Temperature Advanced Hybrid Electric Vehicle Traction Motor Drives  

SciTech Connect (OSTI)

The state-of-the-art hybrid electric vehicles (HEVs) require the inverter cooling system to have a separate loop to avoid power semiconductor junction over temperatures because the engine coolant temperature of 105?C does not allow for much temperature rise in silicon devices. The proposed work is to develop an advanced soft-switching inverter that will eliminate the device switching loss and cut down the power loss so that the inverter can operate at high-temperature conditions while operating at high switching frequencies with small current ripple in low inductance based permanent magnet motors. The proposed tasks also include high-temperature packaging and thermal modeling and simulation to ensure the packaged module can operate at the desired temperature. The developed module will be integrated with the motor and vehicle controller for dynamometer and in-vehicle testing to prove its superiority. This report will describe the detailed technical design of the soft-switching inverters and their test results. The experiments were conducted both in module level for the module conduction and switching characteristics and in inverter level for its efficiency under inductive and dynamometer load conditions. The performance will be compared with the DOE original specification.

None, None

2012-01-31T23:59:59.000Z

96

To appear in the Wiley Encyclopaedia of Electrical and Electronics Engineering Assistive Devices For People With Motor Disabilities -Kumar, Rahman & Krovi, 1997  

E-Print Network [OSTI]

To appear in the Wiley Encyclopaedia of Electrical and Electronics Engineering Assistive Devices powered devices: #12;To appear in the Wiley Encyclopaedia of Electrical and Electronics Engineering For People With Motor Disabilities - Kumar, Rahman & Krovi, 1997 Assistive Devices For People With Motor

Krovi, Venkat

97

EA-1869: Supplement to General Motors Corp., Electric Vehicle/Battery Manufacturing Application, White Marsh, Maryland, and Wixom, Michigan (DOE/EA-1723-S1)  

Broader source: Energy.gov [DOE]

Based on the analysis in the Environmental Assessment DOE determined that its proposed action, to award a federal grant to General Motors to establish an electric motor components manufacturing and electric drive assembly facility would result in no significant adverse impacts.

98

Proceedings of the 2008 International Conference on Electrical Machines Paper ID 1433 Hybrid Cascaded H-Bridge Multilevel Inverter Motor  

E-Print Network [OSTI]

Cascaded H-Bridge Multilevel Inverter Motor Drive DTC Control for Electric Vehicles F. Khoucha1,2 , S reference is then generated using a hybrid cascaded H-bridge multilevel inverter, where each phase of the inverter can be implemented using a DC source, which would be available from fuel cells, batteries

Paris-Sud XI, Université de

99

System and method for motor parameter estimation  

DOE Patents [OSTI]

A system and method for determining unknown values of certain motor parameters includes a motor input device connectable to an electric motor having associated therewith values for known motor parameters and an unknown value of at least one motor parameter. The motor input device includes a processing unit that receives a first input from the electric motor comprising values for the known motor parameters for the electric motor and receive a second input comprising motor data on a plurality of reference motors, including values for motor parameters corresponding to the known motor parameters of the electric motor and values for motor parameters corresponding to the at least one unknown motor parameter value of the electric motor. The processor determines the unknown value of the at least one motor parameter from the first input and the second input and determines a motor management strategy for the electric motor based thereon.

Luhrs, Bin; Yan, Ting

2014-03-18T23:59:59.000Z

100

Subcontract Report: Final Report on Assessment of Motor Technologies for Traction Drives of Hybrid and Electric Vehicles (Subcontract #4000080341)  

SciTech Connect (OSTI)

Currently, interior permanent magnet (IPM) motors with rare-earth (RE) magnets are almost universally used for hybrid and electric vehicles (EVs) because of their superior properties, particularly power density. However, there is now a distinct possibility of limited supply or very high cost of RE magnets that could make IPM motors unavailable or too expensive. Because development of electric motors is a critical part of the U.S. Department of Energy (DOE) Advanced Power Electronics and Motors activity, DOE needs to determine which options should be investigated and what barriers should be addressed. Therefore, in order to provide a basis for deciding which research topics should be pursued, an assessment of various motor technologies was conducted to determine which, if any, is potentially capable of meeting FreedomCAR 2015 and 2020 targets. Highest priority was given to IPM, surface mounted permanent magnet (SPM), induction, and switched reluctance (SR) motors. Also of interest, but with lesser emphasis, were wheel motors, multiple-rotor motors, motors with external excitation, and several others that emerged from the assessment. Cost and power density (from a design perspective, the power density criterion translates to torque density) are emerging as the two most important properties of motors for traction drives in hybrid and EVs, although efficiency and specific power also are very important. The primary approach for this assessment involved interviews with original equipment manufacturers (OEMs), their suppliers, and other technical experts. For each technology, the following issues were discussed: (1) The current state-of-the-art performance and cost; (2) Recent trends in the technology; (3) Inherent characteristics of the motor - which ones limit the ability of the technology to meet the targets and which ones aid in meeting the target; (4) What research and development (R&D) would be needed to meet the targets; and (5) The potential for the technology to meet the targets. The interviews were supplemented with information from past Oak Ridge National Laboratory (ORNL) reports, previous assessments that were conducted in 2004, and literature on magnet technology. The results of the assessment validated the DOE strategy involving three parallel paths: (1) there is enough of a possibility that RE magnets will continue to be available, either from sources outside China or from increased production in China, that development of IPM motors using RE magnets should be continued with emphasis on meeting the cost target. (2) yet the possibility that RE magnets may become unavailable or too expensive justifies efforts to develop innovative designs for permanent magnet (PM) motors that do not use RE magnets. Possible other magnets that may be substituted for RE magnets include samarium-cobalt (Sm-Co), Alnico, and ferrites. Alternatively, efforts to develop motors that do not use PMs but offer attributes similar to IPM motors also are encouraged. (3) New magnet materials using new alloys or processing techniques that would be less expensive or have comparable or superior properties to existing materials should be developed if possible. IPM motors are by far the most popular choice for hybrid and EVs because of their high power density, specific power, and constant power-speed ratio (CPSR). Performance of these motors is optimized when the strongest possible magnets - i.e., RE neodymium-iron-boron (NdFeB) magnets - are used.

Fezzler, Raymond [BIZTEK Consulting, Inc.

2011-03-01T23:59:59.000Z

Note: This page contains sample records for the topic "4-cylinder electric motor" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


101

EA-1723: General Motors LLC Electric Drive Vehicle Battery and Component Manufacturing Initiative Application White Marsh, Maryland and Wixom, Michigan  

Broader source: Energy.gov [DOE]

DOEs Proposed Action is to provide GM with $105,387,000 in financial assistance in a cost sharing arrangement to facilitate construction and operation of a manufacturing facility to produce electric motor components and assemble an electric drive unit. This Proposed Action through the Vehicle Technologies Program will accelerate the development and production of electric-drive vehicle systems and reduce the United States consumption of petroleum. This Proposed Action will also meaningfully assist in the nations economic recovery by creating manufacturing jobs in the United States in accordance with the objectives of the Recovery Act.

102

Journal of Asian Electric Vehicles, Volume 9, Number 1, June 2011 Uncontrolled Generation of Traciton Motors in Hybrid Electric Vehicles  

E-Print Network [OSTI]

magnet synchronous machines (PMSM) are provided with advantages of small size, light weight, and high power density, therefore PMSM are primary choice as traction motors in hybrid vehicles. In addition hybrid vehicles use PMSM [Kassakian , 2000]. However, interior permanent magnet synchronous motor (IPMSM

Mi, Chunting "Chris"

103

Ontario Hydro Motor Efficiency Study  

E-Print Network [OSTI]

Electric motors consume more than one-half of the electrical energy produced by Ontario Hydro. In the residential sector, the major motor load is for refrigerators and freezers while packaged equipment dominate the motor load in the commercial...

Dautovich, D. R.

1980-01-01T23:59:59.000Z

104

Implementing Motor Management  

E-Print Network [OSTI]

Electric motors account for sixty five percent of industrial energy consumed today. There are many opportunities to conserve electricity by using more energy efficient motors and drives. Proven technologies and practices can reduce energy...

Colip, R. L.

105

PM Motor Parametric Design Analyses for a Hybrid Electric Vehicle Traction Drive Application  

SciTech Connect (OSTI)

The Department of Energy's (DOE) Office of FreedomCAR (Cooperative Automotive Research) and Vehicle Technologies office has a strong interest in making rapid progress in permanent magnet (PM) machine development. The DOE FreedomCAR program is directing various technology development projects that will advance the technology and hopefully lead to a near-term request for proposals (RFP) for a to-be-determined level of initial production. This aggressive approach is possible because the technology is clearly within reach and the approach is deemed essential, based on strong market demand, escalating fuel prices, and competitive considerations. In response, this study began parallel development paths that included a literature search/review, development and utilization of multiple parametric models, verification of the modeling methodology, development of an interior PM (IPM) machine baseline design, development of alternative machine baseline designs, and cost analyses for several candidate machines. This report summarizes the results of these activities as of September 2004. This report provides background and summary information for recent machine parametric studies and testing programs that demonstrate both the potential capabilities and technical limitations of brushless PM machines (axial gap and radial gap), the IPM machine, the surface-mount PM machines (interior or exterior rotor), induction machines, and switched-reluctance machines. The FreedomCAR program, while acknowledging the progress made by Oak Ridge National Laboratory (ORNL), Delphi, Delco-Remy International, and others in these programs, has redirected efforts toward a ''short path'' to a marketable and competitive PM motor for hybrid electric vehicle (HEV) traction applications. The program has developed a set of performance targets for the type of traction machine desired. The short-path approach entails a comprehensive design effort focusing on the IPM machine and meeting the performance targets. The selection of the IPM machine reflects industry's confidence in this market-proven design that exhibits a high power density.

Staunton, R.H.

2004-10-11T23:59:59.000Z

106

PM Motor Parametric Design Analyses for Hybrid Electric Vehicle Traction Drive Application: Interim Report  

SciTech Connect (OSTI)

The Department of Energy's (DOE) Office of FreedomCAR (Cooperative Automotive Research) and Vehicle Technologies has a strong interest in making rapid progress in permanent magnet (PM) machine development. The program is directing various technology development projects that will advance the technology and lead to request for proposals (RFP) for manufacturer prototypes. This aggressive approach is possible because the technology is clearly within reach and the approach is deemed essential, based on strong market demand, escalating fuel prices, and competitive considerations. In response, this study began parallel development paths that included a literature search/review, development and utilization of multiple parametric models to determine the effects of design parameters, verification of the modeling methodology, development of an interior PM (IPM) machine baseline design, development of alternative machine baseline designs, and cost analyses for several candidate machines. This interim progress report summarizes the results of these activities as of June 2004. This report provides background and summary information for recent machine parametric studies and testing programs that demonstrate both the potential capabilities and technical limitations of brushless PM machines (axial gap and radial gap), the IPM machine, the surface-mount PM machines (interior or exterior rotor), induction machines, and switched reluctance machines. The FreedomCAR program, while acknowledging the progress made by Oak Ridge National Laboratory, Delphi, Delco-Remy International, and others in these programs, has redirected efforts toward a ''short path'' to a marketable and competitive PM motor for hybrid electric vehicle traction applications. The program has developed a set of performance targets for the type of traction machine desired. The short-path approach entails a comprehensive design effort focusing on the IPM machine and meeting the performance targets. The selection of the IPM machine reflects industry's confidence in this market-proven design that exhibits a power density surpassed by no other machine design.

Staunton, R.H.

2004-08-11T23:59:59.000Z

107

Energy Conversion in Lifting Mass Vertically using a DC Electric Motor by Observing Required Time to Lift Object for a Certain Height  

E-Print Network [OSTI]

In lifting mass vertically using a DC electric motor energy conversion from electric energy, through intermediate kinetic energy, to gravitation potential energy shows that time required {\\Delta}t to lift load mass m for height h is dependent quadratically to m. Several approaches to explain the experiment observation are discussed in this work, from ideal energy conversion to numerical solution from differential equation.

Viridi, Sparisoma; Permana, Sidik; Srigutomo, Wahyu; Susilawati, Anggie; Nuryadin, Bebeh Wahid; Nurhasan,

2014-01-01T23:59:59.000Z

108

Energy Conservation and Efficiency Improvement for the Electric Motors Operating in U.S. Oil Fields  

E-Print Network [OSTI]

Because of its versatility, electricity consumption continues to grow all over the world more rapidly than any other energy form. The portion of the United States' primary energy supply used as electricity has expanded from near zero at the turn...

Ula, S.; Cain, W.; Nichols, T.

109

Cost Effective, High Efficiency Integrated Systems Approach To Auxiliary Electric Motors  

SciTech Connect (OSTI)

The CARAT program, carried out by Kinetic Art & Technology Corporation (KAT), has been one of the most commercially successful KAT R&D programs to date. Based on previous development of its technology, KAT designed, constructed and tested a highly efficient motor and controller system under this CARAT program with supplemental commercial funding. Throughout this CARAT effort, the technical objectives have been refined and refocused. Some objectives have been greatly expanded, while others have been minimized. The determining factor in all decisions to refocus the objectives was the commercial need, primarily the needs of KAT manufacturing partners. Several companies are employing the resulting CARAT motor and controller designs in prototypes for commercial products. Two of these companies have committed to providing cost share in order to facilitate the development. One of these companies is a major manufacturing company developing a revolutionary new family of products requiring the ultra-high system efficiency achievable by the KAT motor and controller technologies (known as Segmented ElectroMagnetic Array, or SEMA technology). Another company requires the high efficiency, quiet operation, and control characteristics afforded by the same basic motor and controller for an advanced air filtration product. The combined annual production requirement projected by these two companies exceeds one million units by 2005.

Roy Kessinger; Kanchan Angal; Steve Brewer; Steve Kraihanzel; Lenny Schrank; Jason Wolf

2003-07-15T23:59:59.000Z

110

Cost Effective, High Efficiency Integrated Systems Approach to Auxilliary Electric Motors  

SciTech Connect (OSTI)

The CARAT program, carried out by Kinetic Art & Technology Corporation (KAT), has been one of the most commercially successful KAT R&D programs to date. Based on previous development of its technology, KAT designed, constructed and tested a highly efficient motor and controller system under this CARAT program with supplemental commercial funding. Throughout this CARAT effort, the technical objectives have been refined and refocused. Some objectives have been greatly expanded, while others have been minimized. The determining factor in all decisions to refocus the objectives was the commercial need, primarily the needs of KAT manufacturing partners. Several companies are employing the resulting CARAT motor and controller designs in prototypes for commercial products. Two of these companies have committed to providing cost share in order to facilitate the development. One of these companies is a major manufacturing company developing a revolutionary new family of products requiring the ultra-high system efficiency achievable by the KAT motor and controller technologies (known as Segmented ElectroMagnetic Array, or SEMA technology). Another company requires the high efficiency, quiet operation, and control characteristics afforded by the same basic motor and controller for an advanced air filtration product. The combined annual production requirement projected by these two companies exceeds one million units by 2005.

Roy Kessinger Jr.; Keith Seymour; Kanchan Angal; Jason Wolf; Steve Brewer; Leonard Schrank

2003-09-26T23:59:59.000Z

111

Method for assessing motor insulation on operating motors  

DOE Patents [OSTI]

A method for monitoring the condition of electrical-motor-driven devices. The method is achieved by monitoring electrical variables associated with the functioning of an operating motor, applying these electrical variables to a three phase equivalent circuit and determining non-symmetrical faults in the operating motor based upon symmetrical components analysis techniques.

Kueck, John D. (Oak Ridge, TN); Otaduy, Pedro J. (Oak Ridge, TN)

1997-01-01T23:59:59.000Z

112

Method for assessing motor insulation on operating motors  

DOE Patents [OSTI]

A method for monitoring the condition of electrical-motor-driven devices is disclosed. The method is achieved by monitoring electrical variables associated with the functioning of an operating motor, applying these electrical variables to a three phase equivalent circuit and determining non-symmetrical faults in the operating motor based upon symmetrical components analysis techniques. 15 figs.

Kueck, J.D.; Otaduy, P.J.

1997-03-18T23:59:59.000Z

113

Development of Ultra-Efficient Electric Motors Final Technical Report Covering work from April 2002 through September 2007  

SciTech Connect (OSTI)

High temperature superconducting (HTS) motors offer the potential for dramatic volume and loss reduction compared to conventional, high horspower, industrial motors. This report is the final report on the results of eight research tasks that address some of the issues related to HTS motor development that affect motor efficiency, cost, and reliability.

Rich Schiferl

2008-05-30T23:59:59.000Z

114

A State Regulatory Perspective; New Building, Old Motors, and Marginal Electricity Generation  

E-Print Network [OSTI]

Electricity consumption in Texas is expected to grow at 3.2 percent annually for the next ten years. Utility demand management activities, if effective, may reduce that expected rate of growth. Residential cooling, commercial lighting and cooling...

Treadway, N.

1987-01-01T23:59:59.000Z

115

Hybrid vehicle motor alignment  

DOE Patents [OSTI]

A rotor of an electric motor for a motor vehicle is aligned to an axis of rotation for a crankshaft of an internal combustion engine having an internal combustion engine and an electric motor. A locator is provided on the crankshaft, a piloting tool is located radially by the first locator to the crankshaft. A stator of the electric motor is aligned to a second locator provided on the piloting tool. The stator is secured to the engine block. The rotor is aligned to the crankshaft and secured thereto.

Levin, Michael Benjamin (Ann Arbor, MI)

2001-07-03T23:59:59.000Z

116

ELECTRICAL AND COMPUTER ENGINEERING  

E-Print Network [OSTI]

Edison (prolific inventor), Nikola Tesla (inventor of the electric motor, transformer), Dilbert (comic

Haykin, Simon

117

A Unique Approach to Power Electronics and Motor Cooling in a Hybrid Electric Vehicle Environment  

SciTech Connect (OSTI)

An innovative system for cooling the power electronics of hybrid electric vehicles is presented. This system uses a typical automotive refrigerant R-134a (1,1,1,2 tetrafluoroethane) as the cooling fluid in a system that can be used as either part of the existing vehicle passenger air conditioning system or separately and independently of the existing air conditioner. Because of the design characteristics, the cooling coefficient of performance is on the order of 40. Because liquid refrigerant is used to cool the electronics directly, high heat fluxes can result while maintaining an electronics junction temperature at an acceptable value. In addition, an inverter housing that occupies only half the volume of a conventional inverter has been designed to take advantage of this cooling system. Planned improvements should result in further volume reductions while maintaining a high power level.

Ayers, Curtis William [ORNL; Hsu, John S [ORNL; Lowe, Kirk T [ORNL; Conklin, Jim [ORNL

2007-01-01T23:59:59.000Z

118

Electrochemical Capacitors as Energy Storage in Hybrid-Electric Vehicles: Present Status and Future Prospects  

E-Print Network [OSTI]

blending strategy of the electric motor and engine when thesignificantly lower electric motor power (ex. the singlehybrid even though the electric motor had a peak power of

Burke, Andy; Miller, Marshall

2009-01-01T23:59:59.000Z

119

Motor Energy Saving Opportunities in an Industrial Plant  

E-Print Network [OSTI]

Industrial plants have enormous energy saving opportunities with electric motors. Improving motor efficiency is a conventional wisdom to save energy. Re-engineering affords far greater savings opportunities than motor efficiency improvement. Motor...

Kumar, B.; Elwell, A.

120

Writing Motor Specifications - How to Include Efficiency  

E-Print Network [OSTI]

The escalating cost of electric power coupled with the rapid depletion of our non-renewable resources makes consideration of motor efficiency good sense both from economic and conservation viewpoints. The efficiency of an electric motor can...

Quartermaine, B. J.

1980-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "4-cylinder electric motor" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


121

Batteries for Plug-in Hybrid Electric Vehicles (PHEVs): Goals and the State of Technology circa 2008  

E-Print Network [OSTI]

with the electric motor to maximize efficiency. 3 Pure EVsbattery and electric motor to increase the efficiency of thebattery and electric motor to increase the efficiency of the

Axsen, Jonn; Burke, Andy; Kurani, Kenneth S

2008-01-01T23:59:59.000Z

122

Apparatus and method for servicing an elongated suspended pump motor in an electric power plant with limited access  

DOE Patents [OSTI]

Elongated coolant pumps suspended under steam generators within containment in a power plant with limited access space, are removed and replaced by an elongated maintenance cart with an elongated opening along one side in which the motor is received. Rollers support the cart for conveying the elongated motor in an upright position out from under the steam generator and onto an elevator. The elevator is lowered to transfer support of the cart and motor through trunnions to saddles straddling the elevator for rotation of the cart to a generally horizontal position. The elevator then raises the horizontally disposed cart carrying the motor to a higher floor where it is rolled off the elevator and out through the auxiliary equipment hatch.

Chavez, Rossemary V. (Monroeville, PA); Ekeroth, Douglas E. (Delmont, PA); Johnson, F. Thomas (Baldwin Boro, PA); Matusz, John M. (Plum Boro both of Allegheny County, PA)

1994-01-01T23:59:59.000Z

123

Design and performance evaluation of an electric go-kart and custom permanent magnet brushless DC motor  

E-Print Network [OSTI]

This undergraduate thesis documents the design considerations and specifications of building a personal battery-powered go-kart. This includes designing and building a custom brushless DC motor for use in the drivetrain. ...

Davis, Eli Marc

2012-01-01T23:59:59.000Z

124

Apparatus and method for servicing an elongated suspended pump motor in an electric power plant with limited access  

DOE Patents [OSTI]

Elongated coolant pumps suspended under steam generators within containment in a power plant with limited access space, are removed and replaced by an elongated maintenance cart with an elongated opening along one side in which the motor is received. Rollers support the cart for conveying the elongated motor in an upright position out from under the steam generator and onto an elevator. The elevator is lowered to transfer support of the cart and motor through trunnions to saddles straddling the elevator for rotation of the cart to a generally horizontal position. The elevator then raises the horizontally disposed cart carrying the motor to a higher floor where it is rolled off the elevator and out through the auxiliary equipment hatch. 14 figures.

Chavez, R.V.; Ekeroth, D.E.; Johnson, F.T.; Matusz, J.M.

1994-04-26T23:59:59.000Z

125

Electric Motor Thermal Management  

Broader source: Energy.gov [DOE]

2013 DOE Hydrogen and Fuel Cells Program and Vehicle Technologies Program Annual Merit Review and Peer Evaluation Meeting

126

Motor monitoring method and apparatus using high frequency current components  

DOE Patents [OSTI]

A motor current analysis method and apparatus for monitoring electrical-motor-driven devices. The method and apparatus utilize high frequency portions of the motor current spectra to evaluate the condition of the electric motor and the device driven by the electric motor. The motor current signal produced as a result of an electric motor is monitored and the low frequency components of the signal are removed by a high-pass filter. The signal is then analyzed to determine the condition of the electrical motor and the driven device.

Casada, Donald A. (Knoxville, TN)

1996-01-01T23:59:59.000Z

127

Motor monitoring method and apparatus using high frequency current components  

DOE Patents [OSTI]

A motor current analysis method and apparatus for monitoring electrical-motor-driven devices are disclosed. The method and apparatus utilize high frequency portions of the motor current spectra to evaluate the condition of the electric motor and the device driven by the electric motor. The motor current signal produced as a result of an electric motor is monitored and the low frequency components of the signal are removed by a high-pass filter. The signal is then analyzed to determine the condition of the electrical motor and the driven device. 16 figs.

Casada, D.A.

1996-05-21T23:59:59.000Z

128

UQM Patents Non-Rare Earth Magnet Motor under DOE-Supported Project...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

propulsion systems for electric, hybrid electric, plug-in hybrid electric and fuel cell electric vehicles recently patented a new design for electric vehicle motors that use...

129

Rotary Electrodynamics of a DC Motor: Motor as Mechanical Capacitor Lab 2: Modeling and System Identification  

E-Print Network [OSTI]

). · im is the current through the motor. Because the motor is in series with all other electrical). Because power is conserved, m = Kmim (motor efficiency is actually closer to 69%). Here, Km 0.00767 VRotary Electrodynamics of a DC Motor: Motor as Mechanical Capacitor Lab 2: Modeling and System

130

Topic 7 Organization of Motor System -Cortical Motor Areas  

E-Print Network [OSTI]

Cartoon, 1986 Electrical stimulation produces movement of contralateral body parts. #12;4 Motor Homunculus previous stimulation technique · Insert electrode into cortical layer V and use electrical stimulation" somatotopic map vs "more complex" map #12;

Sergio, Lauren E.

131

Advanced Motors  

SciTech Connect (OSTI)

Project Summary Transportation energy usage is predicted to increase substantially by 2020. Hybrid vehicles and fuel cell powered vehicles are destined to become more prominent as fuel prices rise with the demand. Hybrid and fuel cell vehicle platforms are both dependent on high performance electric motors. Electric motors for transportation duty will require sizeable low-speed torque to accelerate the vehicle. As motor speed increases, the torque requirement decreases which results in a nearly constant power motor output. Interior permanent magnet synchronous motors (IPMSM) are well suited for this duty. , , These rotor geometries are configured in straight lines and semi circular arc shapes. These designs are of limited configurations because of the lack of availability of permanent magnets of any other shapes at present. We propose to fabricate rotors via a novel processing approach where we start with magnet powders and compact them into a net shape rotor in a single step. Using this approach, widely different rotor designs can be implemented for efficiency. The current limitation on magnet shape and thickness will be eliminated. This is accomplished by co-filling magnet and soft iron powders at specified locations in intricate shapes using specially designed dies and automatic powder filling station. The process fundamentals for accomplishing occurred under a previous Applied Technology Program titled, ???????????????¢????????????????????????????????Motors and Generators for the 21st Century???????????????¢???????????????????????????????. New efficient motor designs that are not currently possible (or cost prohibitive) can be accomplished by this approach. Such an approach to motor fabrication opens up a new dimension in motor design. Feasibility Results We were able to optimize a IPMSM rotor to take advantage of the powder co-filling and DMC compaction processing methods. The minimum low speed torque requirement of 5 N-m can be met through an optimized design with magnet material having a Br capability of 0.2 T. This level of magnetic performance can be met with a variety of bonded magnet compositions. The torque ripple was found to drop significantly by using thinner magnet segments. The powder co-filling and subsequent compaction processing allow for thinner magnet structures to be formed. Torque ripple can be further reduced by using skewing and pole shaping techniques. The techniques can be incorporated into the rotor during the powder co-filling process.

Knoth, Edward A.; Chelluri, Bhanumathi; Schumaker, Edward J.

2012-12-14T23:59:59.000Z

132

EE443L Lab 2: Modeling a DC Motor Introduction  

E-Print Network [OSTI]

: In this lab we will develop and validate a basic model of a permanent magnet DC motor (Yaskawa Electric MINI: The DC motor is a common actuator in control systems that converts electrical energy into rotational Procedure: Through the following steps, motor parameters for the Yaskawa Electric MINI-Minertia motor

Wedeward, Kevin

133

Motor current signature analysis method for diagnosing motor operated devices  

DOE Patents [OSTI]

A motor current noise signature analysis method and apparatus for remotely monitoring the operating characteristics of an electric motor-operated device such as a motor-operated valve. Frequency domain signal analysis techniques are applied to a conditioned motor current signal to distinctly identify various operating parameters of the motor driven device from the motor current signature. The signature may be recorded and compared with subsequent signatures to detect operating abnormalities and degradation of the device. This diagnostic method does not require special equipment to be installed on the motor-operated device, and the current sensing may be performed at remote control locations, e.g., where the motor-operated devices are used in accessible or hostile environments.

Haynes, Howard D. (Kingston, TN); Eissenberg, David M. (Oak Ridge, TN)

1990-01-01T23:59:59.000Z

134

FY 2014 Annual Progress Report - Electric Drive Technologies...  

Energy Savers [EERE]

(composed of automakers Ford Motor Company, General Motors Company, and Chrysler Group), Tesla Motors, and representatives of the electric utility and petroleum industries. Known...

135

Ultracapacitor Technologies and Application in Hybrid and Electric Vehicles  

E-Print Network [OSTI]

hybrids with high power electric motors for which it may beusing only a 6 kW electric motor. Vehicle projects inhybrids with high power electric motors for which it may be

Burke, Andy

2009-01-01T23:59:59.000Z

136

Conducting a Motor Survey: Key Step for Establishing a Motor Management Policy  

E-Print Network [OSTI]

Roughly 70% of the energy consumed by manufacturing processes is used by electric motors. According to the U.S. Department of Energy, greater attention to motor systems management can reduce motor-related energy costs by 18%. Establishing a motor...

Miller, R. B.

137

The LatestThe LatestThe LatestThe Latest,,,, Quick Motor EvaluationQuick Motor EvaluationQuick Motor EvaluationQuick Motor Evaluation Myway Plus Development of Specialized Equipment  

E-Print Network [OSTI]

is different from the mainstream PM motor, the rotor does not use neodymium but electrically magnetized body. The simple structure and half price of PM motor equipment is highly anticipated in hybrid electric vehicleThe LatestThe LatestThe LatestThe Latest,,,, Quick Motor EvaluationQuick Motor Evaluation

Kambhampati, Patanjali

138

ECE 438 Electric and Hybrid Vehicles Catalog Description: History of electric traction. Introduction to electric and hybrid-electric  

E-Print Network [OSTI]

ECE 438 ­ Electric and Hybrid Vehicles Catalog Description: History of electric traction. Introduction to electric and hybrid-electric vehicle configurations. Vehicle mechanics. Energy sources and storage. Range prediction. Motor for HEVs. Electric drive components. Vehicle transmission system. Credits

139

Abstract--There are two types of drivers in production machine systems: constant velocity (CV) motor and servo-motor.  

E-Print Network [OSTI]

the dynamic model of the five-bar hybrid mechanism including its electric motors. Section 3 presents) motor and servo-motor. If a system contains two drivers or more, among which some are of the CV motor while the other are the servo-motor, the system has the so-called hybrid driver architecture

Zhang, WJ "Chris"

140

Low-cost motor drive embedded fault diagnosis systems  

E-Print Network [OSTI]

Electric motors are used widely in industrial manufacturing plants. Bearing faults, insulation faults, and rotor faults are the major causes of electric motor failures. Based on the line current analysis, this dissertation mainly deals with the low...

Akin, Bilal

2009-05-15T23:59:59.000Z

Note: This page contains sample records for the topic "4-cylinder electric motor" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


141

Performance, Charging, and Second-use Considerations for Lithium Batteries for Plug-in Electric Vehicles  

E-Print Network [OSTI]

power required by the electric motor. The characteristics ofthe battery size and the electric motor and engine powers,electric range and electric motor power (mid-size passenger

Burke, Andrew

2009-01-01T23:59:59.000Z

142

Motor Packaging with Consideration of Electromagnetic and Material...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Documents & Publications Motor Packaging with Consideration of Electromagnetic and Material Characteristics Alnico and Ferrite Hybrid Excitation Electric Machines Wireless Charging...

143

Journal of Asian Electric Vehicles, Volume 8, Number 1, June 2010 Simplified Thermal Model of PM Motors in Hybrid Vehicle Applications Taking  

E-Print Network [OSTI]

mounted PM synchronous motor (SPMSM) is developed in this paper. Due to the high conductivity of the rare of PM Motors in Hybrid Vehicle Applications Taking into Account Eddy Current Loss in Magnets Xiaofeng, University of Michigan-Dearborn, mi@ieee.org Abstract Permanent Magnet (PM) Motors are popular choices

Mi, Chunting "Chris"

144

Motor Packaging with Consideration of Electromagnetic and Material...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

& Publications Alnico and Ferrite Hybrid Excitation Electric Machines Motor Packaging with Consideration of Electromagnetic and Material Characteristics Electric Machine R&D...

145

Submersible canned motor transfer pump  

DOE Patents [OSTI]

A transfer pump used in a waste tank for transferring high-level radioactive liquid waste from a waste tank and having a column assembly, a canned electric motor means, and an impeller assembly with an upper impeller and a lower impeller connected to a shaft of a rotor assembly. The column assembly locates a motor housing with the electric motor means adjacent to the impeller assembly which creates an hydraulic head, and which forces the liquid waste, into the motor housing to cool the electric motor means and to cool and/or lubricate the radial and thrust bearing assemblies. Hard-on-hard bearing surfaces of the bearing assemblies and a ring assembly between the upper impeller and electric motor means grind large particles in the liquid waste flow. Slots in the static bearing member of the radial bearing assemblies further grind down the solid waste particles so that only particles smaller than the clearances in the system can pass therethrough, thereby resisting damage to and the interruption of the operation of the transfer pump. The column assembly is modular so that sections can be easily assembled, disassembled and/or removed. A second embodiment employs a stator jacket which provides an alternate means for cooling the electric motor means and lubricating and/or cooling the bearing assemblies, and a third embodiment employs a variable level suction device which allows liquid waste to be drawn into the transfer pump from varying and discrete levels in the waste tank.

Guardiani, Richard F. (Ohio Township, Allegheny County, PA); Pollick, Richard D. (Sarver, PA); Nyilas, Charles P. (Monroeville, PA); Denmeade, Timothy J. (Lower Burrell, PA)

1997-01-01T23:59:59.000Z

146

Segmented rail linear induction motor  

DOE Patents [OSTI]

A segmented rail linear induction motor has a segmented rail consisting of a plurality of nonferrous electrically conductive segments aligned along a guideway. The motor further includes a carriage including at least one pair of opposed coils fastened to the carriage for moving the carriage. A power source applies an electric current to the coils to induce currents in the conductive surfaces to repel the coils from adjacent edges of the conductive surfaces.

Cowan, Jr., Maynard (1107 Stagecoach Rd. SE., Albuquerque, NM 87123); Marder, Barry M. (1412 Pinnacle View Dr. NE., Albuquerque, NM 87123)

1996-01-01T23:59:59.000Z

147

Segmented rail linear induction motor  

DOE Patents [OSTI]

A segmented rail linear induction motor has a segmented rail consisting of a plurality of nonferrous electrically conductive segments aligned along a guideway. The motor further includes a carriage including at least one pair of opposed coils fastened to the carriage for moving the carriage. A power source applies an electric current to the coils to induce currents in the conductive surfaces to repel the coils from adjacent edges of the conductive surfaces. 6 figs.

Cowan, M. Jr.; Marder, B.M.

1996-09-03T23:59:59.000Z

148

the 4th Power Electronics, Drive Systems & Technologies Conference, PEDSTC 2013 Simultaneous Sensing cum Actuating Linear Motor  

E-Print Network [OSTI]

of an electric machine (a linear motor) without using conventional sensors. Tested is a back-drivable linear motor stage which uses the linear motor electric machine as simultaneous sensor cum actuator, and mechanical impedance of the motor by measuring the motor's time variant electrical impedance. The method

Paris-Sud XI, Université de

149

NREL: Vehicles and Fuels Research - Hybrid Electric Fleet Vehicle...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Hybrid Electric Fleet Vehicle Testing How Hybrid Electric Vehicles Work Hybrid electric vehicles combine a primary power source, an energy storage system, and an electric motor to...

150

Batteries for Plug-in Hybrid Electric Vehicles (PHEVs): Goals and the State of Technology circa 2008  

E-Print Network [OSTI]

a PHEV has both an electric motor and a heat engineusuallythe vehicle only by an electric motor using electricity fromand forth with the electric motor to maximize efficiency.

Axsen, Jonn; Burke, Andy; Kurani, Kenneth S

2008-01-01T23:59:59.000Z

151

Rare-Earth-Free Nanostructure Magnets: Rare-Earth-Free Permanent Magnets for Electric Vehicle Motors and Wind Turbine Generators: Hexagonal Symmetry Based Materials Systems Mn-Bi and M-type Hexaferrite  

SciTech Connect (OSTI)

REACT Project: The University of Alabama is developing new iron- and manganese-based composite materials for use in the electric motors of EVs and renewable power generators that will demonstrate magnetic properties superior to todays best rare-earth-based magnets. Rare earths are difficult and expensive to refine. EVs and renewable power generators typically use rare earths to make their electric motors smaller and more powerful. The University of Alabama has the potential to improve upon the performance of current state-of-the-art rare-earth-based magnets using low-cost and more abundant materials such as manganese and iron. The ultimate goal of this project is to demonstrate improved performance in a full-size prototype magnet at reduced cost.

None

2012-01-01T23:59:59.000Z

152

Analysis of Class 8 Hybrid-Electric Truck Technologies Using Diesel, LNG, Electricity, and Hydrogen, as the Fuel for Various Applications  

E-Print Network [OSTI]

CI) combustion, an electric motor, and a lithium-ion batterypowertrain using one electric motor in the pre-transmissionthe same shaft as the electric motor and the transmission.

Zhao, Hengbing

2013-01-01T23:59:59.000Z

153

Submersible canned motor mixer pump  

DOE Patents [OSTI]

A mixer pump used in a waste tank for mobilizing high-level radioactive liquid waste having a column assembly containing power cables, a motor housing with electric motor means which includes a stator can of a stator assembly and a rotor can of a rotor assembly, and an impeller assembly with an impeller connected to a shaft of the rotor assembly. The column assembly locates the motor housing with the electric motor means adjacent to the impeller which creates an hydraulic head, and which forces the liquid waste into the motor housing to cool the electric motor means and to lubricate radial and thrust bearing assemblies. Hard-on-hard bearing surfaces of the bearing assemblies and a ring assembly between the impeller and electric motor means act to grind down large particles in the liquid waste flow. These larger particles are received in slots in the static bearing members of the radial bearing assemblies. Only solid waste particles smaller than the clearances in the system can pass therethrough, thereby resisting damage to and the interruption of the operation of the mixer pump.

Guardiani, Richard F. (Ohio Township, PA); Pollick, Richard D. (Sarver, PA)

1997-01-01T23:59:59.000Z

154

Submersible canned motor mixer pump  

DOE Patents [OSTI]

A mixer pump is described used in a waste tank for mobilizing high-level radioactive liquid waste having a column assembly containing power cables, a motor housing with electric motor means which includes a stator can of a stator assembly and a rotor can of a rotor assembly, and an impeller assembly with an impeller connected to a shaft of the rotor assembly. The column assembly locates the motor housing with the electric motor means adjacent to the impeller which creates an hydraulic head, and which forces the liquid waste into the motor housing to cool the electric motor means and to lubricate radial and thrust bearing assemblies. Hard-on-hard bearing surfaces of the bearing assemblies and a ring assembly between the impeller and electric motor means act to grind down large particles in the liquid waste flow. These larger particles are received in slots in the static bearing members of the radial bearing assemblies. Only solid waste particles smaller than the clearances in the system can pass there through, thereby resisting damage to and the interruption of the operation of the mixer pump. 10 figs.

Guardiani, R.F.; Pollick, R.D.

1997-10-07T23:59:59.000Z

156

A Novel Approach to Determining Motor Load  

E-Print Network [OSTI]

A NOVEL APPROACH TO DETERMINING MOTOR LOAD by Michael Brown Georgia Tech Research Institute Atlanta, Georgia ABSTRACf Properly sized electric motors are essential if industrial plant efficiency is to be optimized and energy costs... minimized. Because of the difficully in making power measurements on three phase motors, loading is rarely, if ever, checked. A simple indication of motor load can be achieved by measuring operating speed because speed and load are almost linearly...

Brown, M.

157

U.S. Department of Energy's Motor Challenge Program: A National...  

Broader source: Energy.gov (indexed) [DOE]

industry needs, and market drivers associated with improving industrial electric motor-driven systems. The key strategies and tactics being employed by the DOE Motor...

158

Ultracapacitor Technologies and Application in Hybrid and Electric Vehicles  

E-Print Network [OSTI]

maximum efficiency using only a 6 kW electric motor. Vehiclemaximum efficiency using only a 6 kW electric motor. Vehicleelectric motor had a peak power of only 6 kW. Engine operating efficiency

Burke, Andy

2009-01-01T23:59:59.000Z

159

Total Economics of Energy Efficient Motors  

E-Print Network [OSTI]

Due to the large increases in cost of electrical energy in recent years, the energy savings attainable with the use of energy-efficient motors is very attractive to all motor users. But energy and electric demand charge savings tell only part...

Nester, A. T.

1984-01-01T23:59:59.000Z

160

Sixth Northwest Conservation and Electric Power Plan Chapter 1: Introduction  

E-Print Network [OSTI]

electricity can provide, such as heat for homes, lights for commercial buildings, or motors for industrial

Note: This page contains sample records for the topic "4-cylinder electric motor" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


161

Demodulation circuit for AC motor current spectral analysis  

DOE Patents [OSTI]

A motor current analysis method for the remote, noninvasive inspection of electric motor-operated systems. Synchronous amplitude demodulation and phase demodulation circuits are used singly and in combination along with a frequency analyzer to produce improved spectral analysis of load-induced frequencies present in the electric current flowing in a motor-driven system.

Hendrix, Donald E. (Oak Ridge, TN); Smith, Stephen F. (Knoxville, TN)

1990-12-18T23:59:59.000Z

162

ELECTRIC  

Office of Legacy Management (LM)

you nay give us will be greatly uppreckted. VPry truly your23, 9. IX. Sin0j3, Mtinager lclectronics and Nuclear Physics Dept. omh , WESTINGHOUSE-THE NAT KING IN ELECTRICITY...

163

Method for assessing in-service motor efficiency and in-service motor/load efficiency  

DOE Patents [OSTI]

A method and apparatus for assessing the efficiency of an in-service motor. The operating characteristics of the in-service motor are remotely measured. The operating characteristics are then applied to an equivalent circuit for electrical motors. Finally the equivalent circuit is evaluated to determine the performance characteristics of said in-service motor. Based upon the evaluation an individual is able to determine the rotor speed, power output, efficiency, and toque of the in-service motor. Additionally, an individual is able to confirm the calculations by comparing measured values with values obtained as a result of the motor equivalent circuit evaluation.

Kueck, John D. (Oak Ridge, TN); Otaduy, Pedro J. (Oak Ridge, TN)

1997-01-01T23:59:59.000Z

164

Powertrain system for a hybrid electric vehicle  

DOE Patents [OSTI]

A hybrid electric powertrain system is provided including an electric motor/generator drivingly engaged with the drive shaft of a transmission. The electric is utilized for synchronizing the rotation of the drive shaft with the driven shaft during gear shift operations. In addition, a mild hybrid concept is provided which utilizes a smaller electric motor than typical hybrid powertrain systems. Because the electric motor is drivingly engaged with the drive shaft of the transmission, the electric motor/generator is driven at high speed even when the vehicle speed is low so that the electric motor/generator provides more efficient regeneration. 34 figs.

Reed, R.G. Jr.; Boberg, E.S.; Lawrie, R.E.; Castaing, F.J.

1999-08-31T23:59:59.000Z

165

Powertrain system for a hybrid electric vehicle  

DOE Patents [OSTI]

A hybrid electric powertrain system is provided including an electric motor/generator drivingly engaged with the drive shaft of a transmission. The electric is utilized for synchronizing the rotation of the drive shaft with the driven shaft during gear shift operations. In addition, a mild hybrid concept is provided which utilizes a smaller electric motor than typical hybrid powertrain systems. Because the electric motor is drivingly engaged with the drive shaft of the transmission, the electric motor/generator is driven at high speed even when the vehicle speed is low so that the electric motor/generator provides more efficient regeneration.

Reed, Jr., Richard G. (Royal Oak, MI); Boberg, Evan S. (Hazel Park, MI); Lawrie, Robert E. (Whitmore Lake, MI); Castaing, Francois J. (Bloomfield Township, MI)

1999-08-31T23:59:59.000Z

166

Electric Motor R&D  

Broader source: Energy.gov [DOE]

2013 DOE Hydrogen and Fuel Cells Program and Vehicle Technologies Program Annual Merit Review and Peer Evaluation Meeting

167

Variable Frequency Drives: Energy Savings and Impact on Motor Performance  

E-Print Network [OSTI]

, and Pitfalls: Motor Acoustic Noise, Motor Heating. This paper is intended for plant engineers and maintenance personnel who have some practical experience with electrical and mechanical equipment, but are not VFD experts....

Petro, D.

168

Learning from Consumers: Plug-In Hybrid Electric Vehicle (PHEV) Demonstration and Consumer Education, Outreach, and Market Research Program  

E-Print Network [OSTI]

battery and electric motor to increase the efficiency of thebattery and electric motor to increase the efficiency of theand electric motor are used to improve the efficiency of the

Kurani, Kenneth S; Axsen, Jonn; Caperello, Nicolette; Davies, Jamie; Stillwater, Tai

2009-01-01T23:59:59.000Z

169

Submersible canned motor transfer pump  

DOE Patents [OSTI]

A transfer pump is described which is used in a waste tank for transferring high-level radioactive liquid waste from a waste tank and having a column assembly, a canned electric motor means, and an impeller assembly with an upper impeller and a lower impeller connected to a shaft of a rotor assembly. The column assembly locates a motor housing with the electric motor means adjacent to the impeller assembly which creates an hydraulic head, and which forces the liquid waste, into the motor housing to cool the electric motor means and to cool and/or lubricate the radial and thrust bearing assemblies. Hard-on-hard bearing surfaces of the bearing assemblies and a ring assembly between the upper impeller and electric motor means grind large particles in the liquid waste flow. Slots in the static bearing member of the radial bearing assemblies further grind down the solid waste particles so that only particles smaller than the clearances in the system can pass there through, thereby resisting damage to and the interruption of the operation of the transfer pump. The column assembly is modular so that sections can be easily assembled, disassembled and/or removed. A second embodiment employs a stator jacket which provides an alternate means for cooling the electric motor means and lubricating and/or cooling the bearing assemblies, and a third embodiment employs a variable level suction device which allows liquid waste to be drawn into the transfer pump from varying and discrete levels in the waste tank. 17 figs.

Guardiani, R.F.; Pollick, R.D.; Nyilas, C.P.; Denmeade, T.J.

1997-08-19T23:59:59.000Z

170

The China Motor Systems Energy Conservation Program: A major national initiative to reduce motor system energy use in China  

SciTech Connect (OSTI)

Electric motor systems are widely used in China to power fans, pumps, blowers, air compressors, refrigeration compressors, conveyers, machinery, and many other types of equipment. Overall, electric motor systems consume more than 600 billion kWh annually, accounting for more than 50 percent of China's electricity use. There are large opportunities to improve the efficiency of motor systems. Electric motors in China are approximately 2-4 percent less efficient on average than motors in the U.S. and Canada. Fans and pumps in China are approximately 3-5 percent less efficient than in developed countries. Even more importantly, motors, fans, pumps, air compressors and other motor-driven equipment are frequently applied with little attention to system efficiency. More optimized design, including appropriate sizing and use of speed control strategies, can reduce energy use by 20 percent or more in many applications. Unfortunately, few Chinese enterprises use or even know about these energy-saving practices. Opportunities for motor system improvements are probably greater in China than in the U.S. In order to begin capturing these savings, China is establishing a China Motor Systems Energy Conservation Program. Elements of this program include work to develop minimum efficiency standards for motors, a voluntary ''green motor'' labeling program for high-efficiency motors, efforts to develop and promote motor system management guidelines, and a training, technical assistance and financing program to promote optimization of key motor systems.

Nadel, Steven; Wang, Wanxing; Liu, Peter; McKane, Aimee T.

2001-05-31T23:59:59.000Z

171

Analytical Target Cascading Optimization of an Electric Vehicle Powertrain System  

E-Print Network [OSTI]

curves and motor power loss maps produced by an electric vehicle (EV) powertrain system. Three, since the motor performance information (torque curves and power loss map) significantly impacts

Papalambros, Panos

172

Comparative Analysis of Control Techniques for Efficiency Improvement in Electric Vehicles  

E-Print Network [OSTI]

-SVM scheme is the best candidate. Keywords--Electric vehicle, induction motor, efficiency, field oriented. In fact, the motor drive, comprising of the electric motor, power converter, and electronic controller by the driver. Many researches [2-3] have demonstrated the induction motor is one of the right electric motor

173

United States Industrial Motor Systems Market Opportunities Assessment...  

Broader source: Energy.gov (indexed) [DOE]

Executive Summary (December 1998) More Documents & Publications United States Industrial Electric Motor Systems Market Opportunities Assessment Pulp and Paper Mills: Profiting...

174

BPM Motors in Residential Gas Furnaces: What are the Savings?  

E-Print Network [OSTI]

standby power consumption in BPM furnaces is significantlytotal electricity consumption by BPM furnaces. This is notOverall, it appears the BPM motors used in furnaces offer

Lutz, James; Franco, Victor; Lekov, Alex; Wong-Parodi, Gabrielle

2006-01-01T23:59:59.000Z

175

A Loss-Minimization DTC Scheme for EV Induction Motors A. Haddoun1  

E-Print Network [OSTI]

of an induction motor propelling and Electric Vehicle (EV). The proposed control strategy, based on a Direct Flux, among EV's motor electric propulsion features; the energy efficiency is a basic characteristic and the performance of the proposed control approach. Index Terms--Electric vehicle, induction motor, DTC, loss

Paris-Sud XI, Université de

176

Piezoelectric wave motor  

DOE Patents [OSTI]

A piezoelectric motor having a stator in which piezoelectric elements are contained in slots formed in the stator transverse to the desired wave motion. When an electric field is imposed on the elements, deformation of the elements imposes a force perpendicular to the sides of the slot, deforming the stator. Appropriate frequency and phase-shifting of the electric field will produce a wave in the stator and motion in a rotor. In a preferred aspect, the piezoelectric elements are configured so that deformation of the elements in the direction of an imposed electric field, generally referred to as the d.sub.33 direction, is utilized to produce wave motion in the stator. In a further aspect, the elements are compressed into the slots so as to minimize tensile stresses on the elements in use.

Yerganian, Simon Scott (Lee's Summit, MO)

2003-02-11T23:59:59.000Z

177

Piezoelectric wave motor  

DOE Patents [OSTI]

A piezoelectric motor having a stator in which piezoelectric elements are contained in slots formed in the stator transverse to the desired wave motion. When an electric field is imposed on the elements, deformation of the elements imposes a force perpendicular to the sides of the slot, deforming the stator. Appropriate frequency and phase shifting of the electric field will produce a wave in the stator and motion in a rotor. In a preferred aspect, the piezoelectric elements are configured so that deformation of the elements in direction of an imposed electric field, generally referred to as the d.sub.33 direction, is utilized to produce wave motion in the stator. In a further aspect, the elements are compressed into the slots so as to minimize tensile stresses on the elements in use.

Yerganian, Simon Scott (Lee's Summit, MO)

2001-07-17T23:59:59.000Z

178

Solid State AC Motor Drives - Conservation Perspectives  

E-Print Network [OSTI]

This paper presents and discusses techniques for energy conservation by reducing losses in ac motor driven systems, proposed by the technical community in response to surging cost of energy. An important aspect considered is the impact on electric...

Mohan, N.; Ferraro, R. J.

1982-01-01T23:59:59.000Z

179

A Fuzzy-Based Strategy to Improve Control Reconfiguration Performance of a Sensor Fault-Tolerant Induction Motor Propulsion  

E-Print Network [OSTI]

recovery in the Electric (EV) or Hybrid Electric Vehicle (HEV) induction motor drive. To achieve this goal-ref · Fault Tolerant Controller HybridHybrid ElectricElectric VehicleVehicle Induction Motor Sensorless Fuzzy) and the minimization of the size and the weight of the motor and the drive. All these aspect call for an efficiency

Paris-Sud XI, Université de

180

An Activity-Based Assessment of the Potential Impacts of Plug-In Hybrid Electric Vehicles on Energy and Emissions Using One-Day Travel Data  

E-Print Network [OSTI]

Vehicle (BEV) with an electric motor capable of supplyingmode operation uses the electric motor to run during low-PHEV x can be run on the electric motor only for the first x

Recker, W. W.; Kang, J. E.

2010-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "4-cylinder electric motor" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


181

HEV Fleet Testing - Summary Fact Sheet 2010 Ford Fusion vin#4757  

Broader source: Energy.gov (indexed) [DOE]

www.eere.energy.govinformationcenter Vehicle Specifications Engine: 2.5 L 4-cylinder Electric Motor: 60 kW Battery: NiMH Seatbelt Positions: Five Payload: 850 lbs Features:...

182

HEV Fleet Testing - Summary Fact Sheet for 2010 Ford Fusion  

Broader source: Energy.gov (indexed) [DOE]

Ford Fusion VIN 3FADP0L32AR194699 Vehicle Specifications Engine: 2.5 L 4-cylinder Electric Motor: 60 kW Battery: NiMH Seatbelt Positions: Five Payload: 850 lbs Features:...

183

HEV Fleet Testing - Summary Fact Sheet for 2010 Honda Insight  

Broader source: Energy.gov (indexed) [DOE]

courts, law offices, and medical facilities on city streets and urban freeways. Vehicle Specifications Engine: 1.3 L 4-cylinder Electric Motor: 10 kW Battery: NiMH Seatbelt...

184

HEV Fleet Testing - Summary Fact Sheet for 2010 Toyota Prius  

Broader source: Energy.gov (indexed) [DOE]

courts, law offices, and medical facilities on city streets and urban freeways. Vehicle Specifications Engine: 1.8 L 4-cylinder Electric Motor: 60 kW Battery: NiMH Seatbelt...

185

HEV Fleet Testing - Summary Fact Sheet 2010 Toyota Prius  

Broader source: Energy.gov (indexed) [DOE]

Toyota Prius VIN JTDKN3DU2A5010462 Vehicle Specifications Engine: 1.8 L 4-cylinder Electric Motor: 60 kW Battery: NiMH Seatbelt Positions: Five Payload: 885 lbs Features:...

186

Design and Implementation of an Electric Differential for Traction Application  

E-Print Network [OSTI]

and transmissions with lighter and smaller electric motors directly coupled to the wheels via a single gear or an in-wheel motor. This paper deals then with an Electric Differential System (EDS) for an Electric Vehicle (EV angle with good static and dynamic performances. Index Terms--Electric Vehicle (EV), induction motor

Paris-Sud XI, Université de

187

How to Improve Productivity with Energy-Efficient Motors  

E-Print Network [OSTI]

productivity is to reduce costs, particularly those which are rising faster than others such as electricity. Today's new energy efficient motors reduce the kilowatts consumed, thus reducing electric bills and improving productivity. This paper will discuss...

Curley, J. P.

1983-01-01T23:59:59.000Z

188

Power-Factor and Torque Calculation with Consideration of Cross Saturation of the Interior Permanent Magnet Synchronous Motor with  

E-Print Network [OSTI]

motor of a hybrid electric vehicle. I. INTRODUCTION The interior permanent magnet synchronous motor for application in a hybrid electric vehicle. The BFE structure enables the motor to control the magnitude Permanent Magnet Synchronous Motor with Brushless Field Excitation Seong Taek Lee1,2 , Timothy A. Burress1

Tolbert, Leon M.

189

Reduced vibration motor winding arrangement  

DOE Patents [OSTI]

An individual phase winding arrangement having a sixty electrical degree phase belt width for use with a three phase motor armature includes a delta connected phase winding portion and a wye connected phase winding portion. Both the delta and wye connected phase winding portions have a thirty electrical degree phase belt width. The delta and wye connected phase winding portions are each formed from a preselected number of individual coils each formed, in turn, from an unequal number of electrical conductor turns in the approximate ratio of {radical}3. The individual coils of the delta and wye connected phase winding portions may either be connected in series or parallel. This arrangement provides an armature winding for a three phase motor which retains the benefits of the widely known and utilized thirty degree phase belt concept, including improved mmf waveform and fundamental distribution factor, with consequent reduced vibrations and improved efficiency. 4 figs.

Slavik, C.J.; Rhudy, R.G.; Bushman, R.E.

1997-11-11T23:59:59.000Z

190

Cooling devices and methods for use with electric submersible pumps  

DOE Patents [OSTI]

Cooling devices for use with electric submersible pump motors include a refrigerator attached to the end of the electric submersible pump motor with the evaporator heat exchanger accepting all or a portion of the heat load from the motor. The cooling device can be a self-contained bolt-on unit, so that minimal design changes to existing motors are required.

Jankowski, Todd A; Hill, Dallas D

2014-12-02T23:59:59.000Z

191

Electric turbocompound control system  

DOE Patents [OSTI]

Turbocompound systems can be used to affect engine operation using the energy in exhaust gas that is driving the available turbocharger. A first electrical device acts as a generator in response to turbocharger rotation. A second electrical device acts as a motor to put mechanical power into the engine, typically at the crankshaft. Apparatus, systems, steps, and methods are described to control the generator and motor operations to control the amount of power being recovered. This can control engine operation closer to desirable parameters for given engine-related operating conditions compared to actual. The electrical devices can also operate in "reverse," going between motor and generator functions. This permits the electrical device associated with the crankshaft to drive the electrical device associated with the turbocharger as a motor, overcoming deficient engine operating conditions such as associated with turbocharger lag.

Algrain, Marcelo C. (Dunlap, IL)

2007-02-13T23:59:59.000Z

192

Thermoelectric generator for motor vehicle  

DOE Patents [OSTI]

A thermoelectric generator for producing electric power for a motor vehicle from the heat of the exhaust gasses produced by the engine of the motor vehicle. The exhaust gasses pass through a finned heat transfer support structure which has seat positions on its outside surface for the positioning of thermoelectric modules. A good contact cylinder provides a framework from which a spring force can be applied to the thermoelectric modules to hold them in good contact on their seats on the surface of the heat transfer support structure.

Bass, John C. (6121 La Pintra Dr., La Jolla, CA 92037)

1997-04-29T23:59:59.000Z

193

Thermoelectric generator for motor vehicle  

SciTech Connect (OSTI)

A thermoelectric generator is described for producing electric power for a motor vehicle from the heat of the exhaust gases produced by the engine of the motor vehicle. The exhaust gases pass through a finned heat transfer support structure which has seat positions on its outside surface for the positioning of thermoelectric modules. A good contact cylinder provides a framework from which a spring force can be applied to the thermoelectric modules to hold them in good contact on their seats on the surface of the heat transfer support structure. 8 figs.

Bass, J.C.

1997-04-29T23:59:59.000Z

194

A self-reconfigurable and fault-tolerant induction motor control architecture  

E-Print Network [OSTI]

. Index Terms-- Fault tolerant, induction motor drive, hy- brid electric vehicule, observers. I the major requirements of automotive electric traction [1]. Several failures afflict electrical motor drives electric vehicles M. Hilairet, D. Diallo and M.E.H. Benbouzid Abstract-- This paper describes an adaptive

Paris-Sud XI, Université de

195

Vehicle Technologies Office: Electric Drive Technologies  

Broader source: Energy.gov [DOE]

Advanced power electronics and electric motors (APEEM) that make up vehicles' electric drive system are essential to hybrid and plug-in electric vehicles. As such, improvements in these...

196

Abstract--Linear electrical loading system (LELS) driven by electrical cylinder with permanent magnet synchronous  

E-Print Network [OSTI]

magnet synchronous motor (PMSM) offers several advantages of high transmission efficiency and high cylinder driven by permanent magnet synchronous motor (PMSM). Though direct-drive linear motors has some to direct-drive linear motor, the solution of electrical cylinder with PMSM has larger output force

Yao, Bin

197

Electric vehicles  

SciTech Connect (OSTI)

Quiet, clean, and efficient, electric vehicles (EVs) may someday become a practical mode of transportation for the general public. Electric vehicles can provide many advantages for the nation's environment and energy supply because they run on electricity, which can be produced from many sources of energy such as coal, natural gas, uranium, and hydropower. These vehicles offer fuel versatility to the transportation sector, which depends almost solely on oil for its energy needs. Electric vehicles are any mode of transportation operated by a motor that receives electricity from a battery or fuel cell. EVs come in all shapes and sizes and may be used for different tasks. Some EVs are small and simple, such as golf carts and electric wheel chairs. Others are larger and more complex, such as automobile and vans. Some EVs, such as fork lifts, are used in industries. In this fact sheet, we will discuss mostly automobiles and vans. There are also variations on electric vehicles, such as hybrid vehicles and solar-powered vehicles. Hybrid vehicles use electricity as their primary source of energy, however, they also use a backup source of energy, such as gasoline, methanol or ethanol. Solar-powered vehicles are electric vehicles that use photovoltaic cells (cells that convert solar energy to electricity) rather than utility-supplied electricity to recharge the batteries. This paper discusses these concepts.

Not Available

1990-03-01T23:59:59.000Z

198

Frequently Asked Questions on: The Impacts of the Energy Policy Act of 1992 on Industrial End Users of Electric Motor-Driven Systems  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious Rank EERE:YearRound-UpHeatMulti-Dimensional Electrical Resistivity Structure |Accomplishments |LLCfor DOEon:

199

Understanding premium-efficiency motor economics  

SciTech Connect (OSTI)

This paper reports that from a numerical standpoint, motors in continuous-duty service comprise only a fraction of those used in America's industrial plants. Not all plant engineers, however, are aware that the relatively few motors in continuous-duty service account for about 75% of all industrial electrical use. For motors in continuous-duty service, a few percentage points gain in efficiency can yield tremendous reductions in the plant electric bill energy charge. Acknowledgment of this fact has spawned the common practice of replacing less-efficient motors with types of more energy-efficient design. However, arbitrary application of this retrofit practice can be a costly mistake. To maximize return on investment, some basic factors must be understood and considered.

Hirzel, J. (GE Motors, Fort Wayne, IN (US))

1992-04-30T23:59:59.000Z

200

Efficiency test on the Buchanan pump motor  

E-Print Network [OSTI]

representing the Lower Colorado River Authority, Fargo Engineering Company~ and the Westinghouse Electric Corporation began conducting the necessary tests to determine the efficiency of the machine, The first test conducted obtained data for a no... excitation the motor breaker was tripped and the motor allowed to decelerate, The Buchanan powerhouse synchroscope was used to determine the time at which the mctor was turning at rated speed. On a signal from the operator at that instant simultaneous...

Krezdorn, Roy Rankin

1954-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "4-cylinder electric motor" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


201

Electric Power Controller for Steering Wheel Management in Electric Cars  

E-Print Network [OSTI]

Electric Power Controller for Steering Wheel Management in Electric Cars Vicente Milanés, Joshué-- Autonomous vehicles, Power control, System analysis and design, Intelligent transportation systems. I they are named hydraulic power steering (HPS) systems. If an electric motor is used then they are named electric

Paris-Sud XI, Université de

202

Implementing Motor Decision Plans  

E-Print Network [OSTI]

Implementing Motor Decision Plans R. Neal Elliott, Ph.D., P.E., Senior Associate American Council for an Energy-Efficient Economy (ACEEE), Washington, DC Abstract The first step to reducing energy costs and increasing reliability in motors... when a motor fails and must either be replaced or repaired. This is represented visually in Figure 1. When purchasing a motor for a new application, time is usually available to consider various options. However, once a motor has failed...

Elliott, R. N.

203

Motor current signature analysis for determining operational readiness of motor-operated valves (MOVs)  

SciTech Connect (OSTI)

Motor current signature analysis (MCSA) is a novel diagnostic process for condition monitoring of electric-motor-driven mechanical equipment (e.g., pumps, motor-operated valves, compressors, and processing machinery). The MCSA process identifies, characterizes, and trends over time the instantaneous load variations of mechanical equipment in order to diagnose changes in the condition of the equipment (e.g., due to degradation or service wear), which, if allowed to continue, may lead to failure. It monitors the instantaneous variations (noise content) in the electric current flowing through the power leads to the electric motor that drives the equipment. The motor itself thereby acts as a transducer, sensing both large and small, long-term and rapid, mechanical load variations and converting them to variations in the induced current generated in the motor windings. This motor current noise signature is detected, amplified, and further processed as needed to examine its time domain and frequency domain (spectral) characteristics. The operational principles of MCSA and the nonintrusive data collection apparatus and procedure used with MOVs will be described. Data collected from MOVs in both laboratory and in-plant environments will also be shown to illustrate the ability of MCSA to ''see'' the detailed inner workings of the valve and operator and thus to detect degraded performance at an incipient stage. (Set of 18 vugraphs)

Kryter, R.C.; Haynes, H.D.

1987-01-01T23:59:59.000Z

204

Electric Fuel Pump Condition Monitor System Using Electricalsignature Analysis  

DOE Patents [OSTI]

A pump diagnostic system and method comprising current sensing probes clamped on electrical motor leads of a pump for sensing only current signals on incoming motor power, a signal processor having a means for buffering and anti-aliasing current signals into a pump motor current signal, and a computer having a means for analyzing, displaying, and reporting motor current signatures from the motor current signal to determine pump health using integrated motor and pump diagnostic parameters.

Haynes, Howard D [Knoxville, TN; Cox, Daryl F [Knoxville, TN; Welch, Donald E [Oak Ridge, TN

2005-09-13T23:59:59.000Z

205

Advanced motor driven clamped borehole seismic receiver  

DOE Patents [OSTI]

A borehole seismic tool is described including a borehole clamp which only moves perpendicular to the borehole. The clamp is driven by an electric motor, via a right angle drive. When used as a seismic receiver, the tool has a three part housing, two of which are hermetically sealed. Accelerometers or geophones are mounted in one hermetically sealed part, the electric motor in the other hermetically sealed part, and the clamp and right angle drive in the third part. Preferably the tool includes cable connectors at both ends. Optionally a shear plate can be added to the clamp to extend the range of the tool.

Engler, B.P.; Sleefe, G.E.; Striker, R.P.

1993-02-23T23:59:59.000Z

206

Denton Municipal Electric- Standard Offer Rebate Program  

Broader source: Energy.gov [DOE]

Within the GreenSense program, Denton Municipal Electric's Standard Offer Program provides rebates to large commercial and industrial customers for lighting retrofits, HVAC upgrades and motor...

207

Abstract Efficiency issues of variable-capacitance micromotors are discussed in context of combined drive and motor  

E-Print Network [OSTI]

motors, electric drives, efficiency I. INTRODUCTION An active area of research for commercial of combined drive and motor interaction. It is shown that variable-capacitance motors ideally have nearly, the drive system consisting of both the motor and electronics is not ideal when considering different

Chapman, Patrick

208

Adjustable Speed AC Motor Drives-Applications Problems  

E-Print Network [OSTI]

Adjustable Speed AC Motor Drives Applications Problems by Dr. P. Enjeti Power Quality Laboratory Department ofElectrical Engineering Texas A&M University College Station, TX 77843 Tel: 409-845-7466 Fax: 409-845-6259 Email..., it generates side effects, some which have been recognized only recently. This paper presents a comprehensive coverage of application issues of PWM inverter controlled ac motor drives which include damage to motor insulation due to reflected voltages caused...

Enjeti, P.

209

A motor drive control system for the Lidar Polarimeter  

E-Print Network [OSTI]

A MOTOR DRIVE CONTROL SYSTEM FOR THE LIDAR POLARIMETER A Thesis by Waiming Leung Submitted to the Graduate College of Texas A/M University in partial fulfillment of the requirement for the degree of MASTER OF SCIENCF, May 1977 Major... Subject: Electrical Engineering A MOTOR DRIVE CONTROL SYSTEM FOR THE LIDAR POLARIMETER A Thesis by Waiming Leung Approved as to style and content by: Chairman o Comm' ee ea o epartment Member Mem er May 1977 ABSTRACT A Motor Drive Control...

Leung, Waiming

1977-01-01T23:59:59.000Z

210

High Temperature, Buried Permanent Magnet, Brushless DC Motor  

E-Print Network [OSTI]

Circuit Model Predictions of the motor performance are accomplished with a closed loop electric circuit incorporating the motor. The circuit is broken down into three sub-circuits which are the equivalent generator as motor rotating, the coil pair...,Kang, Jungu Lee, Zhiyang Wang and others who worked with me in Vibration Control and Electrormechanics Laboratory. I also would like to thank Dr. Jinfang Liu and Dr. Heeju Choi at Electron Energy Corporation who constantly support our work. Finally, thanks...

Zhang, Zhengxin

2010-10-12T23:59:59.000Z

211

E-Print Network 3.0 - alternating current motors Sample Search...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

of Astronomy, University of Arizona Collection: Physics 3 ELSEVIER Electric Power Systems Research 42 (1997) 225-228 A model for induction motor aggregation for power system...

212

E-Print Network 3.0 - ac induction motors Sample Search Results  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Page: << < 1 2 3 4 5 > >> 1 Electric Motor Drive Selection Issues for HEV Propulsion Systems: A Comparative Study Summary: semiconductors made it increasingly practical to...

213

Optimizing rotational acceleration curves for minimum energy use in electric  

E-Print Network [OSTI]

Optimizing rotational acceleration curves for minimum energy use in electric motors. 12/15/06 Fall the optimal efficiency of a motor for any input values of motor constants, distance, or time. In every of the inspiration to find which rotational acceleration curve for the used motors would be most efficient. We really

Ruina, Andy L.

214

Molecules, muscles, and machines: Universal performance characteristics of motors  

E-Print Network [OSTI]

Molecules, muscles, and machines: Universal performance characteristics of motors James H. Marden, piston engines, electric motors, and all types of jets. Dependence of force production and stress of materials and mechanisms. Organisms and machines move by exerting forces on their external environment

Marden, James

215

MOTOR SCHEMAS IN ROBOT LEARNING Lynne E. Parker  

E-Print Network [OSTI]

allows robot learning to scale to more complex robots or tasks, thus making practical applicationsMOTOR SCHEMAS IN ROBOT LEARNING Lynne E. Parker Department of Electrical Engineering and Computer in robot learning; Macro actions in robot learning; Basis behaviors for robot learning. Definition Motor

Parker, Lynne E.

216

Products of motor burnout. Final report  

SciTech Connect (OSTI)

The Montreal Protocol of 1987 effectively banned a long list of chlorofluorocarbons (CFCs) traditionally used in air conditioning and refrigeration applications. The refrigeration and air conditioning industries have responded by developing and testing new, alternative refrigerants that are less damaging to the atmosphere upon release. Despite a reputation for quality and reliability, air conditioning systems do occasionally fail. One of the more common failure modes in a hermetic system is a motor burnout. Motor burnouts can occur by various mechanisms. One of the most common scenarios is a locked motor rotor, which may result from a damaged bearing. The resulting electrical motor burnout is caused by overheating of the locked rotor and subsequent failure of the insulation. This is primarily a thermal breakdown process.

Hawley-Fedder, R.; Goerz, D.; Koester, C.; Wilson, M.

1996-03-30T23:59:59.000Z

217

Development of a high power density motor for aircraft propulsion  

E-Print Network [OSTI]

are currently powered by heavy gas turbine engines that require fueling. The development of electric motors to replace gas turbines would be a big step towards accomplishing more efficient aircraft propulsion. The primary objective of this research extends...

Dibua, Imoukhuede Tim Odion

2007-04-25T23:59:59.000Z

218

Learning About Wind Turbine Technology, Motors and Generators...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

focused on topics outside of electric machines, to learn about the physics behind motors and generators. It is hard to believe that this technology has been around for well...

219

The US Motor Systems Market Assessment: Baseline and Survey Methods  

E-Print Network [OSTI]

industrial facilities, a basis for projecting changes in that inventory, and a framework for estimating the effect of Motor Challenge on industrial electric consumption. The paper describes the objectives and principal research activities of the Market...

Rosenberg, M.

220

Lithographically Patterned Channels Spatially Segregate Kinesin Motor  

E-Print Network [OSTI]

* Departments of Bioengineering and Electrical Engineering and Materials Research Institute, The Pennsyl and transporting material at nanoscale dimensions, there is considerable interest in harnessing motor proteins), cumulative forces on the order of nN per µm2 are theoretically possible. The size, efficiency, and potential

Hancock, William O.

Note: This page contains sample records for the topic "4-cylinder electric motor" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


221

Working With Your Motor Service Center  

E-Print Network [OSTI]

For the end user of electric motors, it is important to maximize repair quality at minimum cost. At the same time, most recognize the truth in the old adage "You get what you pay for." Coordination of the expectations of the end user and service...

Yung, C.

222

3M's Motor Challenge Showcase Demonstration Project  

E-Print Network [OSTI]

In January 1994, 3M began the task of optimizing the electric motor systems at 3M Center, a 26 building, 7 million square foot corporate campus. A cross-functional, cross-company team was established which included four 3M employees representing two...

Schultz, S. C.

223

Update of the Status of the U.S. Department of Energy's Motor Challenge Showcase Demonstration Projects  

E-Print Network [OSTI]

This paper presents an update on the status of the U.S. Department of Energy's (DOE) Showcase Demonstration Projects. These projects are part of the DOE Motor Challenge Program, and are aimed at demonstrating increased electric motor system...

Szady, A. J.; Jallouk, P. A.; Olszewski, M.; Scheihing, P.

224

IEEE TRANSACTIONS ON VEHICULAR TECHNOLOGY, VOL. 54, NO. 3, MAY 2005 837 Modeling of a Hybrid Electric Vehicle Powertrain  

E-Print Network [OSTI]

of a hybrid electric vehicle (HEV) powertrain test cell is proposed. The test cell consists of a motor combustion engine (ICE) and an electric motor/generator (EM) in series or parallel configurations. The ICE charges the battery or by- passes the battery to propel the wheels via an electric motor. This electric

Mi, Chunting "Chris"

225

PSU TOYOTA ELECTRIC VEHICLE PROGRAM POLICY JULY 2010  

E-Print Network [OSTI]

PSU TOYOTA ELECTRIC VEHICLE PROGRAM POLICY JULY 2010 Purpose: The University State University Toyota Electric Vehicle Program under which Toyota Motor Sales, U.S.A., Inc. (Toyota Agreement PSU Toyota Electric Vehicle Program Procedures Manual for Individual Users Duration

Bertini, Robert L.

226

Replacing Motors Counting Savings: Results from a 100 Motor Study  

E-Print Network [OSTI]

REPLACING MOTORS, COUNTING SAVINGS: RESULTS FROM A 100 MOTOR STUDY Nicole M. Kaufman Motor Systems Engineer Advanced Energy Raleigh, NC ABSTRACT Software tools such as MotorMaster+ aid facility personnel in conducting payback... analyses for replacing motors. These tools make assumptions on the motors operational efficiency in their calculations. By observing 100 pre-EPCA (Energy Policy & Conservation Act) motors in operation, removing them from service and conducting IEEE...

Kaufman, N. M.

2006-01-01T23:59:59.000Z

227

Electrical instrumentation of a contra-rotating propeller drive system  

E-Print Network [OSTI]

A prototype ship propulsion device based on an electric motor that spins propellers in opposite directions was constructed and tested. The device uses a single motor to spin both propellers without a gearbox. The rotor is ...

Angle, Matthew G. (Matthew Gates)

2011-01-01T23:59:59.000Z

228

Halbach array DC motor/generator  

DOE Patents [OSTI]

A new configuration of DC motor/generator is based on a Halbach array of permanent magnets. This motor does not use ferrous materials so that the only losses are winding losses and losses due to bearings and windage. An "inside-out" design is used as compared to a conventional motor/generator design. The rotating portion, i.e., the rotor, is on the outside of the machine. The stationary portion, i.e., the stator, is formed by the inside of the machine. The rotor contains an array of permanent magnets that provide a uniform field. The windings of the motor are placed in or on the stator. The stator windings are then "switched" or "commutated" to provide a DC motor/generator much the same as in a conventional DC motor. The commutation can be performed by mechanical means using brushes or by electronic means using switching circuits. The invention is useful in electric vehicles and adjustable speed DC drives.

Merritt, Bernard T. (Livermore, CA); Dreifuerst, Gary R. (Livermore, CA); Post, Richard F. (Walnut Creek, CA)

1998-01-01T23:59:59.000Z

229

Halbach array DC motor/generator  

DOE Patents [OSTI]

A new configuration of DC motor/generator is based on a Halbach array of permanent magnets. This motor does not use ferrous materials so that the only losses are winding losses and losses due to bearings and windage. An ``inside-out`` design is used as compared to a conventional motor/generator design. The rotating portion, i.e., the rotor, is on the outside of the machine. The stationary portion, i.e., the stator, is formed by the inside of the machine. The rotor contains an array of permanent magnets that provide a uniform field. The windings of the motor are placed in or on the stator. The stator windings are then ``switched`` or ``commutated`` to provide a DC motor/generator much the same as in a conventional DC motor. The commutation can be performed by mechanical means using brushes or by electronic means using switching circuits. The invention is useful in electric vehicles and adjustable speed DC drives. 17 figs.

Merritt, B.T.; Dreifuerst, G.R.; Post, R.F.

1998-01-06T23:59:59.000Z

230

Electric Motor Architecture R&D  

Broader source: Energy.gov [DOE]

2013 DOE Hydrogen and Fuel Cells Program and Vehicle Technologies Program Annual Merit Review and Peer Evaluation Meeting

231

Determining Electric Motor Load and Efficiency  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious Rank EERE:YearRound-UpHeat Pump Models |Conduct, Parent Company AgreesDesiree Pipkins

232

Selected Bibliography on Electric Motor Repair  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious RankCombustion |Energy Usage » SearchEnergyDepartment of Energy Moniz: WhatM-1 SectionMarchSeismicity3

233

Electric Motor Thermal Management | Department of Energy  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious Rank EERE:YearRound-UpHeat PumpRecord ofESPC ENABLE: ECM Summaryand Contact Information | Department

234

Electric Motor Thermal Management | Department of Energy  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious Rank EERE:YearRound-UpHeat PumpRecord ofESPC ENABLE: ECM Summaryand Contact Information | Department1 DOE

235

Buying an Energy-Efficient Electric Motor  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious Rank EERE:YearRound-Up fromDepartmentTie Ltd:June 2015 < prevBuildingBusiness OpportunityofFEMPBUYING AN

236

Replacing an Oversized and Underloaded Electric Motor  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious RankCombustion | Department ofT ib l L dDepartmentnews-flashesEnergy by Brian (03-94)1 Konstantin

237

An analysis of induction motor testing techniques  

SciTech Connect (OSTI)

There are two main failure mechanisms in induction motors: bearing related and stator related. The Electric Power Research Institute (EPRI) conducted a study which was completed in 1985, and found that near 37% of all failures were attributed to stator problems. Another data source for motor failures is the Nuclear Plant Reliability Data System (NPRDS). This database reveals that approximately 55% of all motors were identified as being degraded before failure occurred. Of these, approximately 35% were due to electrical faults. These are the faults which this paper will attempt to identify through testing techniques. This paper is a discussion of the current techniques used to predict incipient failure of induction motors. In the past, the main tests were those to assess the integrity of the ground insulation. However, most insulation failures are believed to involve turn or strand insulation, which makes traditional tests alone inadequate for condition assessment. Furthermore, these tests have several limitations which need consideration when interpreting the results. This paper will concentrate on predictive maintenance techniques which detect electrical problems. It will present appropriate methods and tests, and discuss the strengths and weaknesses of each.

Soergel, S. [Entergy Operations Inc., Killona, LA (United States)

1996-12-31T23:59:59.000Z

238

Modular PM Motor Drives for Automotive Traction Applications  

SciTech Connect (OSTI)

This paper presents modular permanent magnet (PM) motor drives for automotive traction applications. A partially modularized drive system consisting of a single PM motor and multiple inverters is described. The motor has multiple three-phase stator winding sets and each winding set is driven with a separate three-phase inverter module. A truly modularized inverter and motor configuration based on an axial-gap PM motor is then introduced, in which identical PM motor modules are mounted on a common shaft and each motor module is powered by a separate inverter module. The advantages of the modular approach for both inverter and motor include: (1) power rating scalability--one design meets different power requirements by simply stacking an adequate number of modules, thus avoiding redesigning and reducing the development cost, (2) increased fault tolerance, and (3) easy repairing. A prototype was constructed by using two inverters and an axial-gap PM motor with two sets of three-phase stat or windings, and it is used to assist the diesel engine in a hybrid electric vehicle converted from a Chevrolet Suburban. The effect of different pulse-width-modulation strategies for both motoring and regenerative modes on current control is analyzed. Torque and regenerative control algorithms are implemented with a digital signal processor. Analytical and initial testing results are included in the paper.

Su, G.J.

2001-10-29T23:59:59.000Z

239

Design of a High Performance Ferrite Magnet-Assisted Synchronous Reluctance Motor for an  

E-Print Network [OSTI]

Design of a High Performance Ferrite Magnet- Assisted Synchronous Reluctance Motor for an Electric) ferrite-based permanent magnet-assisted synchronous reluctance motor has been designed for an electric vehicle application. The design steps are outlined. Ferrite magnets have been chosen over conventional Nd

Paderborn, Universität

240

EMISSIONS OF NITROUS OXIDE AND METHANE FROM CONVENTIONAL AND ALTERNATIVE FUEL MOTOR VEHICLES  

E-Print Network [OSTI]

-produced electricity for battery electric vehicles. Already, vehicles powered by compressed natural gas, propane. LIPMAN AND MARK A. DELUCCHI example, promising strategies for powering motor vehicles with reduced GHGEMISSIONS OF NITROUS OXIDE AND METHANE FROM CONVENTIONAL AND ALTERNATIVE FUEL MOTOR VEHICLES

Kammen, Daniel M.

Note: This page contains sample records for the topic "4-cylinder electric motor" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


241

Mechanical fault detection in induction motor drives through stator current monitoring -Theory  

E-Print Network [OSTI]

vibrations lead to acoustic noise, noise monitoring is also a possible approach. However, these methods0 Mechanical fault detection in induction motor drives through stator current monitoring - Theory machines are a key element in many electrical systems. Amongst all types of electric motors, induction

Paris-Sud XI, Université de

242

Course Outline ENG 2MM3 Electrical Circuits & Power  

E-Print Network [OSTI]

-Phase Induction Motor; 5. DC Generators & DC Motors; 6. Efficiency/Heating of Electric Machines; 7. ActiveCourse Outline ENG 2MM3 Electrical Circuits & Power Winter 2010 Instructor: Prof. Matiar Howlader Web Page: www.ece.mcmaster.ca/~mrhowlader/ENG2MM3Notes Text Books: 1. Electrical Power and Controls

Haykin, Simon

243

Course Outline ENG 2MM3 Electrical Circuits & Power  

E-Print Network [OSTI]

-Phase Induction Motor; 5. DC Generators & DC Motors; 6. Efficiency/Heating of Electric Machines; 7. ActiveCourse Outline ENG 2MM3 Electrical Circuits & Power Fall 2010 Instructor: Prof. Matiar Howlader Web Page: www.ece.mcmaster.ca/~mrhowlader/ENG2MM3Notes Text Books: 1. Electrical Power and Controls

Haykin, Simon

244

DEPARTMENT OF ELECTRICAL AND COMPUTER ENGINEERING  

E-Print Network [OSTI]

in control and power electronics and in electric machines are fuelling the application of Electrical Drives will discuss the impact of the electrical motor drives on steering systems technologies. Biography: TomyDEPARTMENT OF ELECTRICAL AND COMPUTER ENGINEERING DISTINGUISHED SPEAKER SEMINAR Thursday, March 24

Linder, Tamás

245

Cost-Effective Design of a Hybrid Electrical Energy Storage System for Electric Vehicles  

E-Print Network [OSTI]

] whereas the efficiency of an electric motor can reach 90% or even higher [13], and (ii) the kinetic energy% in the case of heavy city traffic [17]. As the only source of providing energy to the electric motor.g., in Tesla cars, Nissan Leaf, Ford Focus, etc.). The performance of the EES system in an EV is therefore

Pedram, Massoud

246

Motor Vehicle Record Procedure Objective  

E-Print Network [OSTI]

Motor Vehicle Record Procedure Objective Outline the procedure for obtaining motor vehicle record (MVR) through Fleet Services. Vehicle Operator Policy 3. Operators with 7 or more points on their motor vehicle record

Kirschner, Denise

247

Electric Vehicle (EV) Carsharing in A Senior Adult Community  

E-Print Network [OSTI]

Electric Vehicle (EV) Carsharing in A Senior Adult Community Susan with Nissan Motor Co. to study feasibility of EV carsharing program in senior adult

Kammen, Daniel M.

248

Empire Electric Association- Residential Energy Efficiency Credit Program  

Broader source: Energy.gov [DOE]

Empire Electric Association provides rebates for its commercial customers who upgrade to energy efficient lighting, HVAC equipment, and motors. These rebates are offered in conjunction with [http:...

249

Liquid soap film generates electricity  

E-Print Network [OSTI]

We have observed that a rotating liquid soap film generates electricity when placed between two non-contact electrodes with a sufficiently large potential difference. In our experiments suspended liquid film (water + soap film) is formed on the surface of a circular frame, which is forced to rotate in the $x-y$ horizontal plane by a motor. This system is located at the center of two capacitor-like vertical plates to apply an external electric voltage difference in the $x-$direction. The produced electric current is collected from the liquid film using two conducting electrodes that are separated in the $y-$direction. We previously reported that a liquid film in an external electric field rotates when an electric current passes through it, naming it the liquid film motor (LFM). In this paper we report a novel technique, in which a similar device can be used as an electric generator, converting the rotating mechanical energy to electrical energy. The liquid film electric generator (LFEG) is in stark contrast to the LFM, both of which could be designed similarly in very small scales like micro scales with different applications. Although the device is comparable to commercial electric motors or electric generators, there is a significant difference in their working principles. Usually in an electric motor or generator the magnetic field causes the driving force, while in a LFM or LFEG the Coulomb force is the driving force. This fact is also interesting from the Bio-science point of view and brings a similarity to bio motors. Here we have investigated the electrical characteristics of such a generator for the first time experimentally and modelled the phenomenon with electroconvection governing equations. A numerical simulation is performed using the local approximation for the charge-potential relation and results are in qualitative agreement with experiments.

Ahmad Amjadi; Sadegh Feiz; Reza Montazeri Namin

2014-04-24T23:59:59.000Z

250

Advanced Ultra-High Speed Motor for Drilling  

SciTech Connect (OSTI)

Three (3) designs have been made for two sizes, 6.91 cm (2.72 inch) and 4.29 cm (1.69 inch) outer diameters, of a patented inverted configured Permanent Magnet Synchronous Machines (PMSM) electric motor specifically for drilling at ultra-high rotational speeds (10,000 rpm) and that can utilize advanced drilling methods. Benefits of these motors are stackable power sections, full control (speed and direction) of downhole motors, flow hydraulics independent of motor operation, application of advanced drilling methods (water jetting and abrasive slurry jetting), and the ability of signal/power electric wires through motor(s). Key features of the final designed motors are: fixed non-rotating shaft with stator coils attached; rotating housing with permanent magnet (PM) rotor attached; bit attached to rotating housing; internal channel(s) in a nonrotating shaft; electric components that are hydrostatically isolated from high internal pressure circulating fluids ('muds') by static metal to metal seals; liquid filled motor with smoothed features for minimized turbulence in the motor during operation; and new inverted coated metal-metal hydrodynamic bearings and seals. PMSM, Induction and Switched Reluctance Machines (SRM), all pulse modulated, were considered, but PMSM were determined to provide the highest power density for the shortest motors. Both radial and axial electric PMSM driven motors were designed with axial designs deemed more rugged for ultra-high speed, drilling applications. The 6.91 cm (2.72 inch) OD axial inverted motor can generate 4.18KW (5.61 Hp) power at 10,000 rpm with a 4 Nm (2.95 ft-lbs) of torque for every 30.48 cm (12 inches) of power section. The 6.91 cm (2.72 inch) OD radial inverted motor can generate 5.03 KW (6.74 Hp) with 4.8 Nm (3.54 ft-lb) torque at 10,000 rpm for every 30.48 cm (12 inches) of power section. The 4.29 cm (1.69 inch) OD radial inverted motor can generate 2.56 KW (3.43 Hp) power with 2.44 Nm (1.8 ft-lb) torque at full speed 10,000 rpm for every 30.48 cm (12 inches) of power section. Operating conditions are 300 voltage AC at the motor leads. Power voltage losses in the cables/wirelines to the motor(s) are expected to be about 10% for 5000 feet carrying 2 amperes. Higher voltages and better insulators can lower these losses and carry more amperes. Cutting elements for such high tip velocities are currently not available, consequently these motors will not be built at this time. However, 7.62 cm (3 inch) OD, low speed, PMSM radial electric motors based on this project design are being built under a 2006 Oklahoma Center for the Advancement of Science and Technology 'proof of concept' grant.

Impact Technologies LLC; University of Texas at Arlington

2007-03-31T23:59:59.000Z

251

Department of Electrical and Computer Engineering Department of Electrical and Computer Engineering  

E-Print Network [OSTI]

, electric machines, motor drives, and vehicular power systems. The department also collaboratesDepartment of Electrical and Computer Engineering Department of Electrical and Computer Engineering The Department of Electrical and Computer Engineering offers academic programs in advanced study to gradu- ates

Heller, Barbara

252

Department of Electrical and Computer Engineering Department of Electrical and Computer Engineering  

E-Print Network [OSTI]

systems, power electronics, electric machines, motor drives, and vehicular power systems. The MedicalDepartment of Electrical and Computer Engineering Department of Electrical and Computer Engineering of Electrical and Computer Engineering offers academic programs in advanced study to graduates with technical

Heller, Barbara

253

Method and apparatus for monitoring the rotating frequency of de-energized induction motors  

DOE Patents [OSTI]

The rotational speed of a coasting induction motor is measured by sensing e residual electrical voltages at the power terminals of the motor, thus eliminating the need for conventional tachometer equipment, additional mechanical components or modifications to the induction motor itself. The power terminal voltage signal is detected and transformed into a DC voltage proportional to the frequency of the signal. This DC voltage can be input to the control system of a variable frequency motor controller to regulate the output characteristics thereof relative to the speed of the coasting motor. 6 figs.

Mikesell, H.E.; Lucy, E.

1998-02-03T23:59:59.000Z

254

Advanced motor driven clamped borehole seismic receiver  

DOE Patents [OSTI]

A borehole seismic tool including a borehole clamp which only moves perpendicular to the borehole. The clamp is driven by an electric motor, via a right angle drive. When used as a seismic receiver, the tool has a three part housing, two of which are hermetically sealed. Accelerometers or geophones are mounted in one hermetically sealed part, the electric meter in the other hermetically sealed part, and the clamp and right angle drive in the third part. Preferably the tool includes cable connectors at both ends. Optionally a shear plate can be added to the clamp to extend the range of the tool.

Engler, Bruce P. (Sandoval County, NM); Sleefe, Gerard E. (Bernalillo County, NM); Striker, Richard P. (Bernalillo County, NM)

1993-01-01T23:59:59.000Z

255

Justification for Energy Efficient Motors  

E-Print Network [OSTI]

This paper presents the results of a study of Energy Efficient (or EE) motors in NEMA frame sizes, (1-200 HP). It examines the economics of using EE motors for new motor requirements, as replacements for motors - instead of rewinding...

Buschart, R. J.

1981-01-01T23:59:59.000Z

256

Single phase two pole/six pole motor  

DOE Patents [OSTI]

A single phase alternating current two pole/six pole motor is provided with a main stator winding having six coils disposed unequally around the periphery of the machine. These coils are divided into two groups. When these groups are connected such that their magnetomotive forces are additive, two pole motor operation results. When the polarity of one of the groups is then reversed, six pole motor operation results. An auxiliary stator winding which is similar to the main stator winding is displaced from the main stator winding by 90 electrical degrees on a two pole basis.

Kirschbaum, Herbert S. (Asheville, NC)

1984-01-01T23:59:59.000Z

257

Single phase two pole/six pole motor  

DOE Patents [OSTI]

A single phase alternating current two pole/six pole motor is provided with a main stator winding having six coils disposed unequally around the periphery of the machine. These coils are divided into two groups. When these groups are connected such that their magnetomotive forces are additive, two pole motor operation results. When the polarity of one of the groups is then reversed, six pole motor operation results. An auxiliary stator winding which is similar to the main stator winding is displaced from the main stator winding by 90 electrical degrees on a two pole basis. 12 figs.

Kirschbaum, H.S.

1984-09-25T23:59:59.000Z

258

Energy Efficient Motors  

E-Print Network [OSTI]

Efficiency is only one aspect of motor performance. This paper discusses how efficiency is influenced by such factors as horsepower rating, poles, actual load, and starting requirements. It discusses some of the variables affecting efficiency...

Hoffmeyer, W.

1982-01-01T23:59:59.000Z

259

MotorWeek  

ScienceCinema (OSTI)

In 2008, PBS's MotorWeek, television's original automotive magazine, visited Argonne's Transportation Technology R&D Center "to learn what it really takes to make clean power sources a viable reality."

None

2013-04-19T23:59:59.000Z

260

Markov Process of Muscle Motors  

E-Print Network [OSTI]

We study a Markov random process describing a muscle molecular motor behavior. Every motor is either bound up with a thin filament or unbound. In the bound state the motor creates a force proportional to its displacement from the neutral position. In both states the motor spend an exponential time depending on the state. The thin filament moves at its velocity proportional to average of all displacements of all motors. We assume that the time which a motor stays at the bound state does not depend on its displacement. Then one can find an exact solution of a non-linear equation appearing in the limit of infinite number of the motors.

Yu. Kondratiev; E. Pechersky; S. Pirogov

2007-06-20T23:59:59.000Z

Note: This page contains sample records for the topic "4-cylinder electric motor" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


261

Propulsion system for a motor vehicle using a bidirectional energy converter  

DOE Patents [OSTI]

A motor vehicle propulsion system includes an electrical energy source and a traction motor coupled to receive electrical energy from the electrical energy source. The system also has a first bus provided electrical energy by the electrical energy source and a second bus of relatively lower voltage than the first bus. In addition, the system includes an electrically-driven source of reaction gas for the electrical energy source, the source of reaction gas coupled to receive electrical energy from the first bus. Also, the system has an electrical storage device coupled to the second bus for storing electrical energy at the lower voltage. The system also includes a bidirectional energy converter coupled to convert electrical energy from the first bus to the second bus and from the second bus to the first bus.

Tamor, Michael Alan (Toledo, OH); Gale, Allan Roy (Livonia, MI)

1999-01-01T23:59:59.000Z

262

The History of the Electric Car | Department of Energy  

Broader source: Energy.gov (indexed) [DOE]

country. Instead it was a series of breakthroughs -- from the battery to the electric motor -- in the 1800s that led to the first electric vehicle on the road. In the early part...

263

EE 3410 Electric Power Instructor: Ernest Mendrela  

E-Print Network [OSTI]

, it is generators and motors. We will discuss these various electric machines starting with our very first machines - complex motion - described by two or three space co-ordinates, which is generated in electric1 EE ­ 3410 Electric Power Fall 2003 Instructor: Ernest Mendrela Electromechanical Energy

Koppelman, David M.

264

MotorMaster+ International | Department of Energy  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

of the capabilities and features of MotorMaster+. However, users can evaluate repairreplacement options on a broader range of motors, including 60 hertz (Hz) motors tested under...

265

Bent shaft motor  

DOE Patents [OSTI]

A nonelectromagnetic motor comprising a base, a bent shaft which is rotatable relative to the base wherein the bent shaft comprises a straight portion aligned with a main axis and an offset portion that is offset with respect to the main axis; and a drive means for driving the offset portion of the bent shaft along a generally circular path in a plane perpendicular to the main axis to rotate the bent shaft. The bent shaft and drive means for driving the bent shaft can be selected from piezoelectric, magnetostrictive, rheological and shape memory alloys. The drive means of the nonelectromagnetic motor can additionally comprise a shell which shell surrounds and houses the bent shaft and precesses or gyrates which in turn causes the bent drive shaft to rotate. The nonelectromagnetic motor does not rely on friction for the application of torque upon a rotor. 11 figs.

Benavides, G.L.

1998-05-05T23:59:59.000Z

266

Bent shaft motor  

DOE Patents [OSTI]

A nonelectromagnetic motor comprising a base, a bent shaft which is rotable relative to the base wherein the bent shaft comprises a straight portion aligned with a main axis and an offset portion that is offset with respect to the main axis; and a drive means for driving the offset portion of the bent shaft along a generally circular path in a plane perpendicular to the main axis to rotate the bent shaft. The bent shaft and drive means for driving the bent shaft can be selected from piezoelectric, magnetostrictive, rheological and shape memory alloys. The drive means of the nonelectromagnetic motor can additionally comprise a shell which shell surrounds and houses the bent shaft and precesses or gyrates which in turn causes the bent drive shaft to rotate. The nonelectromagnetic motor does not rely on friction for the application of torque upon a rotor.

Benavides, Gilbert L. (Albuquerque, NM)

1998-01-01T23:59:59.000Z

267

Dynein Motor Domain Shows Ring-Shaped Motor, Buttress  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Dynein Motor Domain Shows Ring-Shaped Motor, Buttress Print Movement is fundamental to life. It takes place even at the cellular level where cargo is continually being transported...

268

Design and prototyping methods for brushless motors and motor control  

E-Print Network [OSTI]

In this report, simple, low-cost design and prototyping methods for custom brushless permanent magnet synchronous motors are explored. Three case-study motors are used to develop, illustrate and validate the methods. Two ...

Colton, Shane W. (Shane William)

2010-01-01T23:59:59.000Z

269

Efficient, Inexpensive Motors: A New Trend in The Motors Market  

E-Print Network [OSTI]

EFFICIENT, INEXPENSIVE MOTORS: A NEW TREND IN THE MOTORS MARKET Ronald G. Wroblewski, P.E. Trainer and Consultant ABSTRACT The Consortiwn for Energy Efficiency (CEE) has established criteria for premium-efficiency motors above the EPACf... standard. CEE has set a wrifonn efficiency benchmark that all market players (manufacturers, utilities, and end-users) can use. Some end-users however, have been reluctant to specify these motors because they think they are too expensive...

Wroblewksi, R. G.

270

EE443L: Intermediate Control Lab Lab2: Modeling a DC motor  

E-Print Network [OSTI]

will develop and validate a basic model of a permanent magnet DC motor (Yaskawa Electric, Mini-series, Minertia of a permanent magnet DC motor, the field current is constant (i.e. a constant magnetic field). It can be shown(t) = input voltage eb(t) = back emf if(t) = field current (t) = shaft angle (t) = torque J = moment

Wedeward, Kevin

271

Induction Motors Bearing Failures Detection and Diagnosis: Park and Concordia Transform  

E-Print Network [OSTI]

to metallurgical damage from interrupted electrical current flow. Increased noise and vibration are typicalInduction Motors Bearing Failures Detection and Diagnosis: Park and Concordia Transform Approaches with the problem of bearing failure detection and diagnosis in induction motors. Indeed, bearings deterioration

Boyer, Edmond

272

Joint Identification of Stepper Motor Parameters and of Initial Encoder Offset  

E-Print Network [OSTI]

procedure to identify at the same time the electrical parameters of a permanent magnet stepper motor (PMSM is present. The standard DQ model of PMSM's assumes that the permanent magnet is lined up with a winding when, offset calibration, sliding modes. 1. INTRODUCTION Permanent Magnet Stepper Motors (PMSM's) are widely

Paris-Sud XI, Université de

273

Evaluating High Efficiency Motor Retrofit  

E-Print Network [OSTI]

In the petrochemical and refining Industries, and most manufacturing plants, the reliable operation of AC motors always has been crucial to the continuous operation of the process. Now, the cost of operating these motors has also become a...

Evans, T. A.

1984-01-01T23:59:59.000Z

274

Magazine R729 Motor prediction  

E-Print Network [OSTI]

Magazine R729 Primer Motor prediction Daniel M. Wolpert* and J. Randall Flanagan The concept of motor prediction was first considered by Helmholtz when trying to understand how we localise visual position of the eye, predicted the gaze position based on a copy of the motor command acting on the eye

Flanagan, Randy

275

RMP Colloquia Modeling molecular motors  

E-Print Network [OSTI]

The authors present general considerations and simple models for the operation of isothermal motors at small structural differences from the usual Carnot engines. Turning to more explicit models for a single motorRMP Colloquia Modeling molecular motors Frank Julicher,* Armand Ajdari, and Jacques Prost

Jlicher, Frank

276

Impact of SiC Devices on Hybrid Electric and Plug-in Hybrid Electric Vehicles  

E-Print Network [OSTI]

Impact of SiC Devices on Hybrid Electric and Plug-in Hybrid Electric Vehicles Hui Zhang1 , Leon M -- The application of SiC devices (as battery interface, motor controller, etc.) in a hybrid electric vehicle (HEV, vehicle simulation software). Power loss models of a SiC inverter are incorporated into PSAT powertrain

Tolbert, Leon M.

277

Electric vehicle drive train with direct coupling transmission  

DOE Patents [OSTI]

An electric vehicle drive train includes an electric motor and an associated speed sensor, a transmission operable in a speed reduction mode or a direct coupled mode, and a controller responsive to the speed sensor for operating the transmission in the speed reduction mode when the motor is below a predetermined value, and for operating the motor in the direct coupled mode when the motor speed is above a predetermined value. The controller reduces the speed of the motor, such as by regeneratively braking the motor, when changing from the speed reduction mode to the direct coupled mode. The motor speed may be increased when changing from the direct coupled mode to the speed reduction mode. The transmission is preferably a single stage planetary gearbox. 6 figures.

Tankersley, J.B.; Boothe, R.W.; Konrad, C.E.

1995-04-04T23:59:59.000Z

278

Electric vehicle drive train with direct coupling transmission  

DOE Patents [OSTI]

An electric vehicle drive train includes an electric motor and an associated speed sensor, a transmission operable in a speed reduction mode or a direct coupled mode, and a controller responsive to the speed sensor for operating the transmission in the speed reduction mode when the motor is below a predetermined value, and for operating the motor in the direct coupled mode when the motor speed is above a predetermined value. The controller reduces the speed of the motor, such as by regeneratively braking the motor, when changing from the speed reduction mode to the direct coupled mode. The motor speed may be increased when changing from the direct coupled mode to the speed reduction mode. The transmission is preferably a single stage planetary gearbox.

Tankersley, Jerome B. (Fredericksburg, VA); Boothe, Richard W. (Roanoke, VA); Konrad, Charles E. (Roanoke, VA)

1995-01-01T23:59:59.000Z

279

Sliding Mode Control of EV Electric Differential System  

E-Print Network [OSTI]

of an electric differential system for Electric Vehicle (EV) with two induction motor drives (one for each wheel of electric drives to control the generated torque and the introduction of an independent control400 1 Sliding Mode Control of EV Electric Differential System A. Haddoun, M. E. H. Benbouzid, D

Paris-Sud XI, Université de

280

Enhancing Location Privacy for Electric Vehicles (at the right time)  

E-Print Network [OSTI]

An electric vehicle (also known as EV) is powered by an electric motor instead of a gasoline engine sudden demands for power). In future development, it has been proposed that such use of electric vehiclesEnhancing Location Privacy for Electric Vehicles (at the right time) Joseph K. Liu1 , Man Ho Au2

Note: This page contains sample records for the topic "4-cylinder electric motor" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


281

Enhancing the stability of kinesin motors for microscale transport applications{  

E-Print Network [OSTI]

714989a Biomolecular motors, such as kinesins, have great potential for micro-actuation and micro, and there has been considerable interest in developing hybrid devices harnessing the mechanical motion provided and electric fields.3­14 However, a major issue in integrating these biological components into functional

Hancock, William O.

282

Position sensor for linear synchronous motors employing halbach arrays  

DOE Patents [OSTI]

A position sensor suitable for use in linear synchronous motor (LSM) drive systems employing Halbach arrays to create their magnetic fields is described. The system has several advantages over previously employed ones, especially in its simplicity and its freedom from being affected by weather conditions, accumulated dirt, or electrical interference from the LSM system itself.

Post, Richard Freeman

2014-12-23T23:59:59.000Z

283

SUPER HIGH-SPEED MINIATURIZED PERMANENT MAGNET SYNCHRONOUS MOTOR  

E-Print Network [OSTI]

with the design of permanent magnet synchronous motors (PMSM) to operate at super-high speed with high efficiency. The designed and fabricated PMSM was successfully tested to run upto 210,000 rpm The designed PMSM has 2000 W concept of electrical machines. After that, the modeling of PMSM for dynamic simulation is provided

Wu, Thomas

284

The Economics of Energy (and Electricity) Demand  

E-Print Network [OSTI]

home to charge up at night. 12 The Tesla Roadster is an electric sport car prototype manufactured by Tesla Motors (http://www.teslamotors.com/). 13 This is based on there being around 25 million homes... 25 3.3.2 Electrification of personal transport New sources of electricity demand may emerge which substantially change the total demand for electricity and the way electricity is consumed by the household. The Tesla Roadster12 stores 53 k...

Platchkov, Laura M.; Pollitt, Michael G.

285

Trexa Motor Corporation TMC | Open Energy Information  

Open Energy Info (EERE)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data CenterFranconia, Virginia:FAQ < RAPID Jump to:Seadov Pty LtdSteen,LtdInformation DixieTraverse Electric Coop,Trenton, NJ)Trexa Motor

286

Preventing Electrical Shock  

E-Print Network [OSTI]

closer to un- guarded energized overhead lines than the following distances: 1) For voltages to ground 50 kV or less?10 feet; 2) For voltages to ground more than 50 kV ?10 feet plus 4 inches for every 10 kV over 50 kV. ? Make sure all electric motors... attempt to unplug the cord, move an energized line with any object, or grab the person to free him. Once the person is free, administer CPR immedi- ately, if necessary, to try to resuscitate the individual. In case of an electrical fi re, turn off...

Smith, David

2004-09-16T23:59:59.000Z

287

Stabilizer for motor vehicle  

SciTech Connect (OSTI)

This patent describes a stabilizer for a motor vehicle comprising: a rod-shaped torsion section extending in the transverse direction of a motor vehicle; a pair of arm sections continuous with both ends of the torsion section and extending in the longitudinal direction of the motor vehicle; a first member attached to the torsion section or at least one of the arm sections and formed with an axially penetrating cylindrical bore; a columnar second member inserted in the bore of the first member; at least one coil spring disposed between the inner peripheral surface of the bore of the first member and the outer peripheral surface of the second member and wound around the second member, at least one end of the coil spring being a free end; an operating member connected to the free end of the coil spring, at least a part of the operating member being located outside the first member; and drive means coupled to the operating member and adapted to apply a force in a direction such that the diameter of the coil spring is increased or reduced.

Takadera, I.; Kuroda, S.

1986-11-11T23:59:59.000Z

288

E-Print Network 3.0 - automotive electrics automotive Sample...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

is the second most energy consuming system after the electric motor. Further, HVAC... air conditioning systems used in the automotive industry are based on vapour-compression...

289

Optimization of induction motor efficiency: Volume 2, Single-phase induction motors: Final report  

SciTech Connect (OSTI)

The optimal design of the motor dimensions, the capacitance of the run capacitor, the winding distribution and the choice of the electrical steel are the most important sources for an improvement of the efficiency of modern single-phase induction motors for given performance and material cost constraints. The formulation of the techniques which realize this optimization is based on nonlinear programming approaches. The Method of Boundary Search Along Active Constraints is used for the optimal design of the motor dimensions of a commercially available 2 hp, 115 V single-phase induction motor. Based on the optimization results due to the above mentioned four optimization components, the relationships between efficiency, power factor, cost, active materials and the values of the capacitance of the run capacitor are studied and the limited validity of the model law is discussed. This report also explains why the Wanlass retrofit improves efficiency and details the advantages and disadvantages of such a retrofitting as compared with the operation in the standard configuration.

Fuchs, E.F.; Huang, H.; Vandenput, A.J.; Holl, J.; Appelbaum, J.; Zak, Z.; Erlicki, M.S.

1987-05-01T23:59:59.000Z

290

Wind motor applications for transportation  

SciTech Connect (OSTI)

Motion equation for a vehicle equipped with a wind motor allows, taking into account the drag coefficients, to determine the optimal wind drag velocity in the wind motor`s plane, and hence, obtain all the necessary data for the wind wheel blades geometrical parameters definition. This optimal drag velocity significantly differs from the flow drag velocity which determines the maximum wind motor power. Solution of the motion equation with low drag coefficients indicates that the vehicle speed against the wind may be twice as the wind speed. One of possible transportation wind motor applications is its use on various ships. A ship with such a wind motor may be substantially easier to steer, and if certain devices are available, may proceed in autonomous control mode. Besides, it is capable of moving within narrow fairways. The cruise speed of a sailing boat and wind-motored ship were compared provided that the wind velocity direction changes along a harmonic law with regard to the motion direction. Mean dimensionless speed of the wind-motored ship appears to be by 20--25% higher than that of a sailing boat. There was analyzed a possibility of using the wind motors on planet rovers in Mars or Venus atmospheric conditions. A Mars rover power and motor system has been assessed for the power level of 3 kW.

Lysenko, G.P.; Grigoriev, B.V.; Karpin, K.B. [Moscow Aviation Inst. (Russian Federation)

1996-12-31T23:59:59.000Z

291

How to Build a Motor  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Motor Sign In About | Careers | Contact | Investors | bpa.gov Search News & Us Expand News & Us Projects & Initiatives Expand Projects & Initiatives Finance & Rates Expand...

292

Motor Repair Tech Brief  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious RankCombustion | Department ofT ib l L d F S i DOE TribaltheMyMinutesDepartmentCharacteristics | Motor Repair

293

Comparison of Early-stage Design Methods for a Two-mode Hybrid Electric Vehicle  

E-Print Network [OSTI]

Whitefoot+ , V. P Atluri*, E Tate*, and P Papalambros+ + University of Michigan * General Motors Company with a vast design space consisting of distinct subsystems, such as engine, motor, transmission, and battery models are detailed high-fidelity simulations of engine and electric motor components combined with two

Papalambros, Panos

294

Electric vehicle system for charging and supplying electrical power  

DOE Patents [OSTI]

A power system that provides power between an energy storage device, an external charging-source/load, an onboard electrical power generator, and a vehicle drive shaft. The power system has at least one energy storage device electrically connected across a dc bus, at least one filter capacitor leg having at least one filter capacitor electrically connected across the dc bus, at least one power inverter/converter electrically connected across the dc bus, and at least one multiphase motor/generator having stator windings electrically connected at one end to form a neutral point and electrically connected on the other end to one of the power inverter/converters. A charging-sourcing selection socket is electrically connected to the neutral points and the external charging-source/load. At least one electronics controller is electrically connected to the charging-sourcing selection socket and at least one power inverter/converter. The switch legs in each of the inverter/converters selected by the charging-source/load socket collectively function as a single switch leg. The motor/generators function as an inductor.

Su, Gui Jia

2010-06-08T23:59:59.000Z

295

School of Public and Environmental Affairs, Indiana University Electric Vehicle Survey Research Team  

E-Print Network [OSTI]

elsewhere as "electric" vehicles). A plug-in electric vehicle is powered by plugging into a specializedSchool of Public and Environmental Affairs, Indiana University Electric Vehicle Survey Research together with the electric motor. A Nissan Leaf is an example of a plug-in electric vehicle. A plug

Craft, Christopher B.

296

Topology, design, analysis and thermal management of power electronics for hybrid electric vehicle  

E-Print Network [OSTI]

Topology, design, analysis and thermal management of power electronics for hybrid electric vehicle an important role in the success of electric, hybrid and fuel cell vehicles. Typical power electronics circuits/DC converter; electric drives; electric vehicles; fuel cell; hybrid electric vehicles; power electronics, motor

Mi, Chunting "Chris"

297

An Improved Fault-Tolerant Control Scheme for PWM Inverter-Fed Induction Motor-Based EVs  

E-Print Network [OSTI]

and simulations on an electric vehicle are carried-out using a European urban driving cycle to show for such systems. In particular, voltage source inverters are a key component of these electric motor drive systems of an electric vehicle on the variable-speed ac drives and particularly on the power inverter is rapidly

Paris-Sud XI, Université de

298

Combined passive bearing element/generator motor  

DOE Patents [OSTI]

An electric machine includes a cylindrical rotor made up of an array of permanent magnets that provide a N-pole magnetic field of even order (where N=4, 6, 8, etc.). This array of permanent magnets has bars of identical permanent magnets made of dipole elements where the bars are assembled in a circle. A stator inserted down the axis of the dipole field is made of two sets of windings that are electrically orthogonal to each other, where one set of windings provides stabilization of the stator and the other set of windings couples to the array of permanent magnets and acts as the windings of a generator/motor. The rotor and the stator are horizontally disposed, and the rotor is on the outside of said stator. The electric machine may also include two rings of ferromagnetic material. One of these rings would be located at each end of the rotor. Two levitator pole assemblies are attached to a support member that is external to the electric machine. These levitator pole assemblies interact attractively with the rings of ferromagnetic material to produce a levitating force upon the rotor.

Post, Richard F. (Walnut Creek, CA)

2000-01-01T23:59:59.000Z

299

Developing a Motor Management Policy at BASF  

E-Print Network [OSTI]

In early 1998 Thomas R. Theising, BASF Corporate Engineering initiated the formation of a motor management team. The goal of the team was to develop a Motor Management Guideline to better manage the purchase and repair of motors used throughout...

Zickefoose, B.; Theising, T. R.

300

Industrial motor repair in the United States  

SciTech Connect (OSTI)

This report characterizes the motor repair industry in the United States; summarizes current motor repair and testing practice; and identifies barriers to energy motor repair practice and recommends strategies for overcoming those barriers.

Schueler, V.; Leistner, P.; Douglass, J.

1994-09-01T23:59:59.000Z

Note: This page contains sample records for the topic "4-cylinder electric motor" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


301

Anatomy and Functional Morphology of the Feeding Apparatus of the Lesser Electric Ray, Narcine  

E-Print Network [OSTI]

Anatomy and Functional Morphology of the Feeding Apparatus of the Lesser Electric Ray, Narcine suspension. The lesser electric ray, Narcine brasiliensis, preys primarily on polychaete annelids using arch) and complex and subdivided cranial musculature, affording fine motor control. However

Motta, Philip J.

302

Verification of Motor Repair Quality  

E-Print Network [OSTI]

Motor testing at Advanced Energy has shown that a motor that has not suffered irreparable damage as a result of failure can be repaired to perform as well as before the failure. But the only way to achieve the performance level of an energy...

Butler, K.

303

Abstract--This paper discusses an optimum design of an ultra high-speed permanent-magnet synchronous motor  

E-Print Network [OSTI]

-magnet synchronous motor (PMSM), which is applied to a supercharger of an automotive engine. Although the motor (PMSM), which is specifically applied to the electric supercharger of the automotive engines. Although the PMSM is operated by an inverter with a 12-V DC bus voltage for an adjustable-speed drive, it must

Fujimoto, Hiroshi

304

West Virginia University 1 Lane Department of Computer Science & Electrical  

E-Print Network [OSTI]

, Motor drives, Power electronics, Electric vehicles. · Ali Feliachi - Ph.D. (Georgia Tech) Power systemsWest Virginia University 1 Lane Department of Computer Science & Electrical Engineering E.S.C.S) · Bachelor of Science in Electrical Engineering (B.S.E.E.) Nature of Program The Department offers

Mohaghegh, Shahab

305

Predictive energy management for hybrid electric vehicles -Prediction horizon and  

E-Print Network [OSTI]

Predictive energy management for hybrid electric vehicles - Prediction horizon and battery capacity of a combined hybrid electric vehicle. Keywords: Hybrid vehicles, Energy Management, Predictive control, Optimal vehicle studied uses a complex transmission composed of planetary gear sets and two electric motors

Paris-Sud XI, Universit de

306

A Sensorless Direct Torque Control Scheme Suitable for Electric Vehicles  

E-Print Network [OSTI]

A Sensorless Direct Torque Control Scheme Suitable for Electric Vehicles Farid Khoucha, Khoudir an Electric Vehicle (EV). The proposed scheme uses an adaptive flux and speed observer that is based on a full is a good candidate for EVs propulsion. Index Terms--Electric vehicle, Induction motor, sensorless drive

Paris-Sud XI, Universit de

307

VT-2014-00407.R1 1 Abstract--Simulation-based design optimization of an electric  

E-Print Network [OSTI]

of a motor design, thus confining its application to the early conceptual design stage. Practical electric analysis accuracy and efficiency, direct integration of a motor model into a system optimization model hasVT-2014-00407.R1 1 Abstract--Simulation-based design optimization of an electric vehicle (EV

Papalambros, Panos

308

he prospect of millions of vehicles plugging into the nation's electric grid in the coming decades  

E-Print Network [OSTI]

: Tesla Motors recently intro- duced an all-electric vehicle. See sidebar, p. 34.) Two startup firms plan of Tesla Motors The all-electric Tesla Roadster can go from 0 to 60 in about 4 sec- onds (see p. 34 ). 28

Firestone, Jeremy

309

CVD facility electrical system captor/dapper study  

SciTech Connect (OSTI)

Project W-441, CVD Facility Electrical System CAPTOWDAPPER Study validates Meier's hand calculations. This study includes Load flow, short circuit, voltage drop, protective device coordination, and transient motor starting (TMS) analyses.

SINGH, G.

1999-10-28T23:59:59.000Z

310

AMO FOA Targets Advanced Components for Next-Generation Electric...  

Office of Environmental Management (EM)

power electronics (i.e., wide band gap devices) with high RPM, high power density and energy efficient megawatt (MW) class electric motors in three primary areas: (1) chemical...

311

Electric vehicle design, racing and distance to empty algorithms  

E-Print Network [OSTI]

This research began with the goal of designing and building an electric motorcycle to compete in the Isle of Man TT Zero race. A set of parametric physics-based models was derived to size the batteries and motors, predict ...

Rodgers, Lennon Patrick

2013-01-01T23:59:59.000Z

312

Field demonstration of three-phase Wanlass motors. Final report Aug 81-Apr 83  

SciTech Connect (OSTI)

Electric motors are major part of the load at Naval shore facilities. The Naval Civil Engineering Laboratory (NCEL) investigated the Wanlass motor as a means of reducing power consumption, reducing current flow, and improving power factor, as compared to standard motors. NCEL surveyed the literature on single-phase and poly-phase Wanlass motors and tested poly-phase Wanlass motors. Efficiency, current, power factor, load sharing, temperature rise, vibration and noise, torque-speed, and reliability were judged. A reduction in current flow and a corresponding improvement in power factor can be expected with the Wanlass rewind. A small improvement in efficiency - a reduction in power consumption - is possible but not certain. It was recommended that Wanlass rewinds not be purchased on the basis of energy savings or power factor improvement.

Dann, G.

1984-01-01T23:59:59.000Z

313

Recover Power with Hydraulic Motors  

E-Print Network [OSTI]

displacement device, the HPRM torque and speed are almost completely independent - unlike hydraulic power recovery turbines (centrifugal motors). Three screw HPRM's have low moments of inertia, operate at low vibration and noise levels and extract power...

Brennan, J. R.

1982-01-01T23:59:59.000Z

314

Direct drive field actuator motors  

DOE Patents [OSTI]

A positive-drive field actuator motor is described which includes a stator carrying at least one field actuator which changes in dimension responsive to application of an energy field, and at least one drive shoe movable by the dimensional changes of the field actuator to contact and move a rotor element with respect to the stator. Various embodiments of the motor are disclosed, and the rotor element may be moved linearly or arcuately. 62 figs.

Grahn, A.R.

1998-03-10T23:59:59.000Z

315

A linear induction motor conveyer  

E-Print Network [OSTI]

A LINEAR INCUCTION MOTOR CONVEYER A Thesis Kenneth Sheldon. Solinsky Submitted to the Graduate College of Texas AkM University in partial fulfillment of the requirement for the degree of MASTER 07 SCIENCE May 1973 Major Subject: Industrial.... Howie, USAMC-ITC-P/P, Red River Army Depot, Texarkana, Texas 75501. Approved owxe, xe , ro uc o uction Engineering For the Commander ne , grec or, I A LINEAR INDUCTION MOTOR CONVEYER A Thesis by Kenneth Sheldon Solinsky App ved as to style...

Solinsky, Kenneth Sheldon

1973-01-01T23:59:59.000Z

316

Radial-Gap Permanent Magnet Motor and Drive Research FY 2004  

SciTech Connect (OSTI)

The objective of this task was to study permanent magnet (PM) radial-gap traction drive systems that could meet the U.S. Department of Energy FreedomCAR Program's 2010 goals to expose weaknesses or identify strengths. Initially, the approach was to compare attributes such as physical deformations during operation, performance (torque, power, efficiency versus speed), material requirements (strength), material costs, manufacturability, weight, power density, specific power, reliability, and drivability for specific motors. Three motors selected were the commercially available 60-kW radial-gap surface-mounted PM motor manufactured by UQM Technologies, Inc.; a hypothetical PM motor with rotor-supported magnets similar to the Honda MCF-21; and Delphi's automotive electric machine drive motor, whose rotor is a ferromagnetic cylinder, held at one end by a shaft that supports the magnets on its inner surface. Potential problems have appeared related to PM motors, such as (1) high no-load spin losses and high operational power losses, probably from eddy current losses in the rotor; (2) the undemonstrated dual mode inverter control (DMIC) for driving a brushless dc motor (BDCM) (UQM and Delphi motors); (3) uncertainty about the potential for reducing current with DMIC; and (4) uncertainty about the relation between material requirements and maximum rotor speed. Therefore, the approach was changed to study in detail three of the comparison attributes: drivability, performance, and material requirements. Drivability and related problems were examined by demonstrating that DMIC may be used to drive an 18-pole 30-kW PM motor to 6000 rpm, where the maximum electrical frequency is 900 Hz. An available axial-gap test motor with 18 poles was used because its control is identical to that of a radial gap PM motor. Performance was analytically examined, which led to a derivation showing that DMIC controls a PM motor so that the motor uses minimum current to produce any power regardless of speed for relative speeds, n = {omega}/{omega}{sub base} {ge} 2. Performance was also examined with efficiency measurements during the 30-kW PM motor test. Material requirements were examined with finite-element analyses (FEA) to determine the speed and location where yield starts and the corresponding deformations and stresses.

McKeever, J.W.

2005-02-11T23:59:59.000Z

317

Analysis, Modeling and Neural Network Traction Control of an Electric Vehicle  

E-Print Network [OSTI]

Analysis, Modeling and Neural Network Traction Control of an Electric Vehicle without Differential Terms--Electric vehicle, electric motor, speed estimation, neural networks, traction control. I. INTRODUCTION Recently, Electric Vehicles (EVs) including fuel-cell and hybrid vehicles have been developed very

Paris-Sud XI, Universit de

318

Performance Analysis and Comparison of Three IPMSM with High Homopolar Inductance for Electric Vehicle Applications  

E-Print Network [OSTI]

Synchronous Motor, Zero-Sequence Inductance, Electric Vehicle, Ripple Torque, Fast evaluation, Harmonics three topologies of PMSM according to the specifications of an electric vehicle (EV) with severe and especially for hybrid electric vehicle (HEV) and electric vehicle (EV). Moreover, interior permanent magnet

Boyer, Edmond

319

AVTA: 2010 Electric Vehicles International Neighborhood Electric...  

Energy Savers [EERE]

10 Electric Vehicles International Neighborhood Electric Vehicle Testing Results AVTA: 2010 Electric Vehicles International Neighborhood Electric Vehicle Testing Results The...

320

Electricity Reliability  

E-Print Network [OSTI]

Electricity Delivery and Energy Reliability High Temperature Superconductivity (HTS) Visualization in the future because they have virtually no resistance to electric current, offering the possibility of new electric power equipment with more energy efficiency and higher capacity than today's systems

Note: This page contains sample records for the topic "4-cylinder electric motor" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


321

Three phase AC motor controller  

DOE Patents [OSTI]

A motor controller for a three phase AC motor (10) which is adapted to operate bidirectionally from signals received either from a computer (30) or a manual control (32). The controller is comprised of digital logic circuit means which implement a forward and reverse command signal channel (27, 29) for the application of power through the forward and reverse power switching relays (16, 18, 20, 22). The digital logic elements are cross coupled to prevent activation of both channels simultaneously and each includes a plugging circuit (65, 67) for stopping the motor upon the removal of control signal applied to one of the two channels (27, 29) for a direction of rotation desired. Each plugging circuit (65, 67) includes a one-shot pulse signal generator (88, 102) which outputs a single pulse signal of predetermined pulsewidth which is adapted to inhibit further operation of the application of power in the channel which is being activated and to apply a reversal command signal to the other channel which provides a reversed phase application of power to the motor for a period defined by the pulse-width output of the one-shot signal generator to plug the motor (10) which will then be inoperative until another rotational command signal is applied to either of the two channels.

Vuckovich, Michael (Elizabeth, PA); Wright, Maynard K. (Bethel Park, PA); Burkett, John P. (South Huntington Township, Westmoreland County, PA)

1984-03-20T23:59:59.000Z

322

Chapter 15. Electric Machinery Electric Machinery  

E-Print Network [OSTI]

countries. As such, much attention has been paid to efficiency of these motors, and in recent years, standards for efficiency of these motors have been raised. Most integral horsepower motors are made with cast aluminum rotors. Because the efficiency of a motor is improved with higher conductivity

323

DOE Fundamentals Handbook: Electrical Science, Volume 4  

SciTech Connect (OSTI)

The Electrical Science Fundamentals Handbook was developed to assist nuclear facility operating contractors provide operators, maintenance personnel, and the technical staff with the necessary fundamentals training to ensure a basic understanding of electrical theory, terminology, and application. The handbook includes information on alternating current (AC) and direct current (DC) theory, circuits, motors, and generators; AC power and reactive transformers; and electrical test components; batteries; AC and DC voltage regulators; instruments and measuring devices. This information will provide personnel with a foundation for understanding the basic operation of various types of DOE nuclear facility electrical equipment.

Not Available

1992-06-01T23:59:59.000Z

324

DOE Fundamentals Handbook: Electrical Science, Volume 3  

SciTech Connect (OSTI)

The Electrical Science Fundamentals Handbook was developed to assist nuclear facility operating contractors provide operators, maintenance personnel, and the technical staff with the necessary fundamentals training to ensure a basic understanding of electrical theory, terminology, and application. The handbook includes information on alternating current (AC) and direct current (DC) theory, circuits, motors and generators; AC power and reactive components; batteries; AC and DC voltage regulators; transformers; and electrical test instruments and measuring devices. This information will provide personnel with a foundation for understanding the basic operation of various types of DOE nuclear facility electrical equipment.

Not Available

1992-06-01T23:59:59.000Z

325

DOE Fundamentals Handbook: Electrical Science, Volume 1  

SciTech Connect (OSTI)

The Electrical Science Fundamentals Handbook was developed to assist nuclear facility operating contractors provide operators, maintenance personnel, and the technical staff with the necessary fundamentals training to ensure a basic understanding of electrical theory, terminology, and application. The handbook includes information on alternating current (AC) and direct current (DC) theory, circuits, motors, and generators; AC power and reactive components; batteries; AC and DC voltage regulators; transformers; and electrical test instruments and measuring devices. This information will provide personnel with a foundation for understanding the basic operation of various types of DOE nuclear facility electrical equipment.

Not Available

1992-06-01T23:59:59.000Z

326

Case Histories of Energy Efficient Motors  

E-Print Network [OSTI]

should be the value read from a reputable manufactur er I s data sheet. COOLING TOWER MOTORS The plant is now replacing 25 hp cooling tower motors with EE motors as the old ones burn out. An adapter base for changing from the old frame size 365... volts and amps from an EE motor and comparing this to readings from an old motor in service on the tower. This was based on an assumption of identical loads and motor power factors. This calculation showed yearly savings very close to the cost...

Riley, J. C.; Comiskey, W. T

327

BPM Motors in Residential Gas Furnaces: What are theSavings?  

SciTech Connect (OSTI)

Residential gas furnaces contain blowers to distribute warm air. Currently, furnace blowers use either a Permanent Split Capacitor (PSC) or a Brushless Permanent Magnet (BPM) motor. Blowers account for the majority of furnace electricity consumption. Therefore, accurate determination of the blower electricity consumption is important for understanding electricity consumption of furnaces. The electricity consumption of blower motors depends on the static pressure across the blower. This paper examines both types of blower motors in non-condensing non-weatherized gas furnaces at a range of static pressures. Fan performance data is based on manufacturer product literature and laboratory tests. We use field-measured static pressure in ducts to get typical system curves to calculate how furnaces would operate in the field. We contrast this with the electricity consumption of a furnace blower operating under the DOE test procedure and manufacturer rated conditions. Furnace electricity use is also affected by operating modes that happen at the beginning and end of each furnace firing cycle. These operating modes are the pre-purge and post-purge by the draft inducer, the on-delay and off-delay of the blower, and the hot surface ignitor operation. To accurately calculate this effect, we use the number of firing cycles in a typical California house in the Central Valley of California. Cooling hours are not considered in the DOE test procedure. We also account for furnace blower use by the air conditioner and stand-by power. Overall BPM motors outperform PSC motors, but the total electricity savings are significantly less than projected using the DOE test procedure conditions. The performance gains depend on the static pressure of the household ducts, which are typically much higher than in the test procedures.

Lutz, James; Franco, Victor; Lekov, Alex; Wong-Parodi, Gabrielle

2006-05-12T23:59:59.000Z

328

ECE alumnus Martin Eberhard and his all-electric Tesla Roadster NEWS FOR ECE ILLINOIS ALUMNI AND FRIENDS  

E-Print Network [OSTI]

the production line at Tesla Motors, a company cofounded by ECE Illinois alumnus Martin Eberhard. I've had Ford. When Tesla Motors is successful, as I predict it will be, many of us may drive an electric carECE alumnus Martin Eberhard and his all-electric Tesla Roadster NEWS FOR ECE ILLINOIS ALUMNI

Liu, Gang "Logan"

329

Real Time Flux Control in PM Motors  

SciTech Connect (OSTI)

Significant research at the Oak Ridge National Laboratory (ORNL) Power Electronics and Electric Machinery Research Center (PEEMRC) is being conducted to develop ways to increase (1) torque, (2) speed range, and (3) efficiency of traction electric motors for hybrid electric vehicles (HEV) within existing current and voltage bounds. Current is limited by the inverter semiconductor devices' capability and voltage is limited by the stator wire insulation's ability to withstand the maximum back-electromotive force (emf), which occurs at the upper end of the speed range. One research track has been to explore ways to control the path and magnitude of magnetic flux while the motor is operating. The phrase, real time flux control (RTFC), refers to this mode of operation in which system parameters are changed while the motor is operating to improve its performance and speed range. RTFC has potential to meet an increased torque demand by introducing additional flux through the main air gap from an external source. It can augment the speed range by diverting flux away from the main air gap to reduce back-emf at high speeds. Conventional RTFC technology is known as vector control [1]. Vector control decomposes the stator current into two components; one that produces torque and a second that opposes (weakens) the magnetic field generated by the rotor, thereby requiring more overall stator current and reducing the efficiency. Efficiency can be improved by selecting a RTFC method that reduces the back-emf without increasing the average current. This favors methods that use pulse currents or very low currents to achieve field weakening. Foremost in ORNL's effort to develop flux control is the work of J. S. Hsu. Early research [2,3] introduced direct control of air-gap flux in permanent magnet (PM) machines and demonstrated it with a flux-controlled generator. The configuration eliminates the problem of demagnetization because it diverts all the flux from the magnets instead of trying to oppose it. It is robust and could be particularly useful for PM generators and electric vehicle drives. Recent efforts have introduced a brushless machine that transfers a magneto-motive force (MMF) generated by a stationary excitation coil to the rotor [4]. Although a conventional PM machine may be field weakened using vector control, the air-gap flux density cannot be effectively enhanced. In Hsu's new machine, the magnetic field generated by the rotor's PM may be augmented by the field from the stationery excitation coil and channeled with flux guides to its desired destination to enhance the air-gap flux that produces torque. The magnetic field can also be weakened by reversing the current in the stationary excitation winding. A patent for advanced technology in this area is pending. Several additional RTFC methods have been discussed in open literature. These include methods of changing the number of poles by magnetizing and demagnetizing the magnets poles with pulses of current corresponding to direct-axis (d-axis) current of vector control [5,6], changing the number of stator coils [7], and controlling the air gap [8]. Test experience has shown that the magnet strengths may vary and weaken naturally as rotor temperature increases suggesting that careful control of the rotor temperature, which is no easy task, could yield another method of RTFC. The purpose of this report is to (1) examine the interaction of rotor and stator flux with regard to RTFC, (2) review and summarize the status of RTFC technology, and (3) compare and evaluate methods for RTFC with respect to maturity, advantages and limitations, deployment difficulty and relative complexity.

Otaduy, P.J.

2005-09-27T23:59:59.000Z

330

Homopolar motor with dual rotors  

DOE Patents [OSTI]

A homopolar motor has a field rotor mounted on a frame for rotation in a first rotational direction and for producing an electromagnetic field, and an armature rotor mounted for rotation on said frame within said electromagnetic field and in a second rotational direction counter to said first rotational direction of said field rotor. The two rotors are coupled through a 1:1 gearing mechanism, so as to travel at the same speed but in opposite directions. This doubles the output voltage and output power, as compared to a motor in which only the armature is rotated. Several embodiments are disclosed. 7 figs.

Hsu, J.S.

1998-12-01T23:59:59.000Z

331

Multilevel Inverters for Electric Vehicle Applications  

SciTech Connect (OSTI)

This paper presents multilevel inverters as an application for all-electric vehicle (EV) and hybrid-electric vehicle (HEV) motor drives. Diode-clamped inverters and cascaded H-bridge inverters, (1) can generate near-sinusoidal voltages with only fundamental frequency switching; (2) have almost no electromagnetic interference (EMI) and common-mode voltage; and (3) make an EV more accessible/safer and open wiring possible for most of an EV'S power system. This paper explores the benefits and discusses control schemes of the cascade inverter for use as an EV motor drive or a parallel HEV drive and the diode-clamped inverter as a series HEV motor drive. Analytical, simulated, and experimental results show the superiority of these multilevel inverters for this new niche.

Habetler, T.G.; Peng, F.Z.; Tolbert, L.M.

1998-10-22T23:59:59.000Z

332

Electric vehicle drive train with contactor protection  

DOE Patents [OSTI]

A drive train for an electric vehicle includes a traction battery, a power drive circuit, a main contactor for connecting and disconnecting the traction battery and the power drive circuit, a voltage detector across contacts of the main contactor, and a controller for controlling the main contactor to prevent movement of its contacts to the closed position when the voltage across the contacts exceeds a predetermined threshold, to thereby protect the contacts of the contactor. The power drive circuit includes an electric traction motor and a DC-to-AC inverter with a capacitive input filter. The controller also inhibits the power drive circuit from driving the motor and thereby discharging the input capacitor if the contacts are inadvertently opened during motoring. A precharging contactor is controlled to charge the input filter capacitor prior to closing the main contactor to further protect the contacts of the main contactor. 3 figures.

Konrad, C.E.; Benson, R.A.

1994-11-29T23:59:59.000Z

333

Electric vehicle drive train with contactor protection  

DOE Patents [OSTI]

A drive train for an electric vehicle includes a traction battery, a power drive circuit, a main contactor for connecting and disconnecting the traction battery and the power drive circuit, a voltage detector across contacts of the main contactor, and a controller for controlling the main contactor to prevent movement of its contacts to the closed position when the voltage across the contacts exceeds a predetermined threshold, to thereby protect the contacts of the contactor. The power drive circuit includes an electric traction motor and a DC-to-AC inverter with a capacitive input filter. The controller also inhibits the power drive circuit from driving the motor and thereby discharging the input capacitor if the contacts are inadvertently opened during motoring. A precharging contactor is controlled to charge the input filter capacitor prior to closing the main contactor to further protect the contacts of the main contactor.

Konrad, Charles E. (Roanoke, VA); Benson, Ralph A. (Roanoke, VA)

1994-01-01T23:59:59.000Z

334

Thermally Conductive Organic Dielectrics for Power Electronics and Electric Motors  

Broader source: Energy.gov [DOE]

2013 DOE Hydrogen and Fuel Cells Program and Vehicle Technologies Program Annual Merit Review and Peer Evaluation Meeting

335

Hybrid and Electric Traction Motor | GE Global Research  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May JunDatastreamsmmcrcalgovInstrumentsruc DocumentationP-SeriesFlickr FlickrGuidedCH2MLLC HistoryVeteranstoHuub van DamHybridHybrid WindA

336

Optimizing Electric Motor Systems at a Corporate Campus Facility  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious RankCombustion | Department ofT ib l L d F SSales LLCDiesel Enginesthe U.S. -- An2008 |

337

Selected Bibliography on Electric Motor Repair | Department of Energy  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious Rank EERE:YearRound-Up from the Gridwise Global1WasteRecoveryAwards SECTION BNewSeizing a CleanSelected

338

DOE Issues Notice of Proposed Rulemaking for Electric Motors Energy  

Broader source: Energy.gov (indexed) [DOE]

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May Jun Jul(Summary) "ofEarly Career Scientists'Montana. DOCUMENTSof Energy DOE ChallengeThese(Notice ofIssuesfor

339

Optimizing Electric Motor Systems at a Corporate Campus Facility |  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious Rank EERE:Year in3.pdfEnergyDepartment ofOil's Impact on Our National-

340

Overview: Advanced Power Electronics and Electric Motors (APEEM...  

Energy Savers [EERE]

DOE Office of Vehicle Technologies "Mega" Merit Review 2008 on February 25, 2008 in Bethesda, Maryland. merit08rogers.pdf More Documents & Publications Advanced Power...

Note: This page contains sample records for the topic "4-cylinder electric motor" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


341

Buying an Energy-Efficient Electric Motor | Department of Energy  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious Rank EERE:Year in Review: Top FiveDepartment of Energy BuildingsBuried andSoft CostsBuy AmericanBuying an

342

EV Everywhere Workshop: Electric Motors and Critical Materials Breakout  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious Rank EERE:Year in Review: TopEnergyIDIQ Contract ESPC IDIQ ContractConsumerof EnergyGroup Report |

343

Next Generation Electric Machines: Megawatt Class Motors FOA Informational  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious Rank EERE: Alternative Fuels DataCombined HeatInformationDepartment ofNational| Department of853926News

344

Advanced Power Electronics and Electric Motors R&D  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious Rank EERE:YearRound-Up fromDepartment of EnergyAdministrative2| Department of Energy 2 DOE Hydrogen||

345

Replacing an Oversized and Underloaded Electric Motor | Department of  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious Rank EERE:Year in3.pdfEnergyDepartmentEnergy DataRemediatedLandsEnergy V-Belts withEnergy

346

Determining Electric Motor Load and Efficiency | Department of Energy  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious Rank EERE:Year in Review: TopEnergy DOEDealingVehicle Battery PlantDetermine Institutional

347

United States Industrial Electric Motor Systems Market Opportunities  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious Rank EERE:YearRound-Up from theDepartment of Dept. ofUSA RS Basic ContractMilestone at2

348

Improved Organics for Power Electronics and Electric Motors | Department of  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious Rank EERE:YearRound-UpHeatMulti-Dimensionalthe U.S. Department-2023Department ofSmartMethodEnergy 2 DOE

349

Improved Organics for Power Electronics and Electric Motors | Department of  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious Rank EERE:YearRound-UpHeatMulti-Dimensionalthe U.S. Department-2023Department ofSmartMethodEnergy 2

350

Ultra-Efficient and Power-Dense Electric Motors  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious RankCombustion |Energy Usage »of EnergyTheTwo New EnergyofDEVELOPMENT ORGANIZATIONS |UltraDepartmentand

351

United States Industrial Electric Motor Systems Market Opportunities Assessment  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious RankCombustion |Energy Usage »of EnergyTheTwo New12.'6/0.2 ...... 13:27 FAX 301O R E W O R D I United

352

Impact of Motor Failures on Payback Periods  

E-Print Network [OSTI]

This paper uses MotorMaster and Vaughen's Complete Price Guide to determine payback periods for different motor failure scenarios. Some scenarios considered are rewinds, reconditions, and replacement of bearings. Prices for these repairs...

Cheek, K. F.; Pillay, P.; Dudley, K. J.

353

Application Guidelines for Energy Efficient Motors  

E-Print Network [OSTI]

Rapidly rising power costs have prompted industrial motor users to consider specifying motors having efficiencies higher than the norm. Blanket specifications calling out high efficiency units for all applications can result in extended deliveries...

Cowern, E. H.

1983-01-01T23:59:59.000Z

354

Self-bearing motor design & control  

E-Print Network [OSTI]

This thesis presents the design, implementation and control of a new class of self-bearing motors. The primary thesis contributions include the design and experimental demonstration of hysteresis self-bearing motors, novel ...

Imani Nejad, Mohammad

2013-01-01T23:59:59.000Z

355

Techniques for energy conservation in ac motor-driven systems. Final report  

SciTech Connect (OSTI)

Techniques for energy conservation of reducing losses in ac motor-driven systems proposed by the technical community in response to surging cost of energy are evaluated and compared. Report objectives are to provide better understanding of underlying principles and to evaluate technical and economic viability of these techniques for various applications. An important aspect considered is the impact on electric utility system in terms of harmonics, power factor of operation, and Electro-Magnetic Interference (EMI). The techniques evaluated are: NASA Power Factor Controller, a simple device for reducing power losses in lightly loaded ac motors; wanlass motor modification, a scheme of reconnecting motor windings with capacitors in series, with the intention of improving the motor efficiencies under all loading conditions; conventional variable frequency solid-state inverters which can control the speed of ac motors by producing adjustable frequency ac voltage, with a significant potential for energy conservation in pumps and air-handling systems; and other variable frequency drives and schemes including cycloconverters, slip-recovery scheme, Exxon Alternating Current Synthesizer, Venturini conversion technique, permanent magnet synchronous motors, and a device called the Phase-Liner. The impact of rapid growth in semiconductors and magnetic materials technologies is also considered.

Mohan, N.

1981-09-01T23:59:59.000Z

356

Frequency modulation drive for a piezoelectric motor  

DOE Patents [OSTI]

A piezoelectric motor has peak performance at a specific frequency f.sub.1 that may vary over a range of frequencies. A drive system is disclosed for operating such a motor at peak performance without feedback. The drive system consists of the motor and an ac source connected to power the motor, the ac source repeatedly generating a frequency over a range from f.sub.1 -.DELTA.x to f.sub.1 +.DELTA.y.

Mittas, Anthony (Albuquerque, NM)

2001-01-01T23:59:59.000Z

357

An Online Mechanism for Multi-Speed Electric Vehicle Charging  

E-Print Network [OSTI]

range of such vehicles, and EVs are expected to represent close to 10% of all vehicle sales by 2020 in electric vehicles (EVs). New hybrid de- signs, equipped with both an electric motor and an internal- nisms to schedule the charging of EVs, such that the local constraints of the distribution network

Southampton, University of

358

Physical model of a hybrid electric drive train  

E-Print Network [OSTI]

A motor and flywheel system was designed to simulate the dynamics of the electric drive train and inertial mass of a hybrid electric vehicle. The model will serve as a test bed for students in 2.672 to study the energy ...

Young, Brady W. (Brady William)

2006-01-01T23:59:59.000Z

359

Evaluation of Retrofit Variable-Speed Furnace Fan Motors  

SciTech Connect (OSTI)

In conjunction with the New York State Energy Research and Development Authority (NYSERDA) and Proctor Engineering Group, Ltd. (PEG), the Consortium for Advanced Residential Buildings (CARB) has evaluated the Concept 3 (tm) replacement motors for residential furnaces. These brushless, permanent magnet (BPM) motors can use much less electricity than their PSC (permanent split capacitor) predecessors. This evaluation focuses on existing homes in the heating-dominated climate of upstate New York with the goals of characterizing field performance and cost-effectiveness. The results of this study are intended to be useful to home performance contractors, HVAC contractors, and home efficiency program stakeholders. The project includes eight homes in and near Syracuse, NY. Tests and monitoring was performed both before and after fan motors were replaced. Average fan power reductions were approximately 126 Watts during heating and 220 Watts during cooling operation. Over the course of entire heating and cooling seasons, these translated into average electric energy savings of 163 kWh. Average cost savings were $20 per year. Homes where the fan was used outside of heating and cooling mode saved an additional $42 per year on average. Results indicate that BPM replacement motors will be most cost-effective in HVAC systems with longer run times and relatively low duct static pressures. More dramatic savings are possible if occupants use the fan-only setting when there is no thermal load. There are millions of cold-climate, U.S. homes that meet these criteria, but the savings in most homes tested in this study were modest.

Aldrich, R.; Williamson, J.

2014-01-01T23:59:59.000Z

360

Analysis of production line motor failure. CRADA final report for CRADA number Y-1293-0215  

SciTech Connect (OSTI)

The Oak Ridge National Laboratory (ORNL) was approached by a Food Products Manufacturer (FPM) to investigate the rapid failure of motors in a manufacturing facility. It was reported that some motors or their bearings were being replaced after as little as four months of service. The deciding symptom for replacement was always high motor vibration. To protect against unscheduled downtime in the middle of a process run, the FPM`s maintenance team removes a motor from service when its vibration level reaches a conservative threshold of approximately 0.4 inches per second. In their experience, motors left in service after reaching this vibration threshold can fail at any time within the time span of the next process run causing significant losses of raw material and production capacity. A peculiar finding of vibration level trend analysis was that at least one motor exhibited cyclic variations with 24-hour periodicity. The vibration level reached a maximum at about 4:00 a.m., ramped down during the day, and then rose again during the night. Another peculiarity was that most of the vibration energy in the affected motors was at the 120 Hz frequency. Since this is twice the 60 Hz line frequency the FPM suspected the vibration was electrically induced. The electric loads at the FPMs plant remain constant during the five days of a continuous production run. Thus, the periodicity of the vibration observed, with its daily peaking at about four am, suggested the possibility of being driven by changes in the electrical power grid external to the plant.

Kueck, J. [Lockheed Martin Energy Systems, Inc., Oak Ridge, TN (United States); Talbott, C. [M& M Mars, Inc., Chicago, IL (United States)

1995-02-10T23:59:59.000Z

Note: This page contains sample records for the topic "4-cylinder electric motor" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


361

Impact of New Federal Efficiency Performance Standards on the Industrial Motor Marketplace  

E-Print Network [OSTI]

Impact of New Federal Efficiency Performance Standards on the Industrial Motor Marketplace R. Neal Elliott, Ph.D., P.E. Associate Director for Research American Council for an Energy-Efficient Economy Washington, DC ABSTRACT.... As noted above, beginning in the 1980's, the National Electrical Manufacturers' Association (NEMA) began including energy efficiency labeling requirements in its major stand MG-1. The efficiencies were based upon the Institute of Electrical...

Elliott, R. N.

362

An investigation of irregular switching in three phase adjustable speed motor drives without neutral connection  

E-Print Network [OSTI]

Phase Adjustable Speed Motor Drives without Neutral Connection. (May 1990) Md. Shamsul Arefeen, B. S. , Bangladesh Univ. of Engg. 8z Technology Chair of Advisory Committee: Dr. M. Ehsani There are many industrial applications where variable speed... There are many industrial application where variable speed drives of electrical ma, - chines are needed. This requirement of high performance electric drives can be met either by a. dc or by an ac machine. Due to cost and ease of control, high performance...

Arefeen, Shamsal

1990-01-01T23:59:59.000Z

363

Energy control strategy for a hybrid electric vehicle  

DOE Patents [OSTI]

An energy control strategy (10) for a hybrid electric vehicle that controls an electric motor during bleed and charge modes of operation. The control strategy (10) establishes (12) a value of the power level at which the battery is to be charged. The power level is used to calculate (14) the torque to be commanded to the electric motor. The strategy (10) of the present invention identifies a transition region (22) for the electric motor's operation that is bounded by upper and lower speed limits. According to the present invention, the desired torque is calculated by applying equations to the regions before, during and after the transition region (22), the equations being a function of the power level and the predetermined limits and boundaries.

Phillips, Anthony Mark (Northville, MI); Blankenship, John Richard (Dearborn, MI); Bailey, Kathleen Ellen (Dearborn, MI); Jankovic, Miroslava (Birmingham, MI)

2002-01-01T23:59:59.000Z

364

Energy control strategy for a hybrid electric vehicle  

DOE Patents [OSTI]

An energy control strategy (10) for a hybrid electric vehicle that controls an electric motor during bleed and charge modes of operation. The control strategy (10) establishes (12) a value of the power level at which the battery is to be charged. The power level is used to calculate (14) the torque to be commanded to the electric motor. The strategy (10) of the present invention identifies a transition region (22) for the electric motor's operation that is bounded by upper and lower speed limits. According to the present invention, the desired torque is calculated by applying equations to the regions before, during and after the transition region (22), the equations being a function of the power level and the predetermined limits and boundaries.

Phillips, Anthony Mark (Northville, MI); Blankenship, John Richard (Dearborn, MI); Bailey, Kathleen Ellen (Dearborn, MI); Jankovic, Miroslava (Birmingham, MI)

2002-08-27T23:59:59.000Z

365

Method and apparatus for monitoring motor operated valve motor output torque and power at valve seating  

DOE Patents [OSTI]

A method and apparatus are provided for monitoring a motor operated valve during the brief period when the valve seats and the torque switch trips to deenergize the valve motor. The method uses voltage measurements on the load side of a deenergizing switch that opens to deenergize the motor to determine, among other things, final motor rotational speed and the decelerating torque at motor deenergization. 14 figs.

Casada, D.A.

1996-01-16T23:59:59.000Z

366

Method and apparatus for monitoring motor operated valve motor output torque and power at valve seating  

DOE Patents [OSTI]

A method and apparatus are provided for monitoring a motor operated valve during the brief period when the valve seats and the torque switch trips to deenergize the valve motor. The method uses voltage measurements on the load side of a deenergizing switch that opens to deenergize the motor to determine, among other things, final motor rotational speed and the decelerating torque at motor deenergization.

Casada, Donald A. (Oak Ridge, TN)

1996-01-01T23:59:59.000Z

367

Central Electric Coop. Oregon Trail Electric Coop. Douglas Electric  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Central Electric Coop. Oregon Trail Electric Coop. Douglas Electric Coop. Blachly- Lane Co. Coop Umatilla Electric Coop. Hermiston Milton- Freewater Idaho Co Light & Power Coop....

368

Control Realization for an Interior Permanent Magnet Synchronous Motor (IPMSM) in Automotive Drive Trains  

E-Print Network [OSTI]

Control Realization for an Interior Permanent Magnet Synchronous Motor (IPMSM) in Automotive Drive Trains Wilhelm Peters, Tobias Huber, Joachim Böcker Power Electronics and Electrical Drives, Paderborn automotive traction drives are a wide speed range, a wide constant-power operation range and high efficiency

Paderborn, Universität

369

Voltage control of emerging distribution systems with induction motor loads using robust LQG approach  

E-Print Network [OSTI]

, electricity is mainly produced by large generation plants, generally located near the primary energy sources has significant performance to improve the voltage profile of the distributed generation system & Sons, Ltd. key words: distributed generation; eigenvalue; H1 norm; induction motor; linear quadratic

Pota, Himanshu Roy

370

Mechanism and kinetics of a sodium-driven bacterial flagellar motor  

E-Print Network [OSTI]

Mechanism and kinetics of a sodium-driven bacterial flagellar motor Chien-Jung Loa,b , Yoshiyuki potential difference. It consists of an 50-nm rotor and up to 10 independent stators anchored to the cell of electrical and chemical potential. All 25 torque­speed curves had the same concave-down shape as fully

Berry, Richard

371

Abstract--Cascaded nonlinear predictive controller for induction motor drive is presented. The load torque,  

E-Print Network [OSTI]

types of electric machines, exhibits several advantages such as lower cost, reliability, simplicity of the machine. Both controllers are applied in a cascade structure to induction motor. The prediction model law minimizes a quadratic performance index of the predicted tracking error for multivariable system

Paris-Sud XI, Université de

372

104 IEEE TRANSACTIONS ON VEHICULAR TECHNOLOGY, VOL. 60, NO. 1, JANUARY 2011 An Adaptive Electric Differential for  

E-Print Network [OSTI]

Differential for Electric Vehicles Motion Stabilization Bekheira Tabbache, Abdelaziz Kheloui, and Mohamed El- tric vehicles (EVs) with two separate induction motor drive-based wheels. In this case, an electric, direct torque control (DTC), electric differential (ED), electric vehicle (EV). NOMENCLATURE s, (r

Boyer, Edmond

373

Chemistry in Motion: Tiny Synthetic Motors  

E-Print Network [OSTI]

In this Account, we describe how synthetic motors that operate by self-diffusiophoresis make use of a self-generated concentration gradient to drive motor motion. A description of propulsion by self-diffusiophoresis is presented for Janus particle motors comprising catalytic and noncatalytic faces. The properties of the dynamics of chemically powered motors are illustrated by presenting the results of particle-based simulations of sphere-dimer motors constructed from linked catalytic and noncatalytic spheres. The geometries of both Janus and sphere-dimer motors with asymmetric catalytic activity support the formation of concentration gradients around the motors. Because directed motion can occur only when the system is not in equilibrium, the nature of the environment and the role it plays in motor dynamics are described. Rotational Brownian motion also acts to limit directed motion, and it has especially strong effects for very small motors. We address the following question: how small can motors be and still exhibit effects due to propulsion, even if only to enhance diffusion? Synthetic motors have the potential to transform the manner in which chemical dynamical processes are carried out for a wide range of applications.

Peter H. Colberg; Shang Yik Reigh; Bryan Robertson; Raymond Kapral

2014-11-03T23:59:59.000Z

374

Electricity on the rig; part I -- electric applications on drilling and workover rigs  

SciTech Connect (OSTI)

This article points out that not only have electric motors replaced diesel engines and mechanical transmissions, but solid-state equipment is rapidly taking the place of rotary equipment in variable speed drivers and control systems. The SCR (silicon controlled rectifier) type of speed control has replaced other types by a large margin of acceptance on drilling rigs and has begun to be used on workover and service rigs. In most cases, electrical power is generated at the rig site with diesel-AC generators. On mechanically driven rigs, single diesel-generator sets operate to supply power for lighting and electrical motor loads. When high levels of power are required, such as on SCR-powered rigs, multiple generators are operated in electrical-parallel and each contributes to the total power required.

McNair, W.L.

1983-03-01T23:59:59.000Z

375

Electrical Engineer  

Broader source: Energy.gov [DOE]

This position is located in the Office of Electric Reliability. The Office of Electric Reliability helps protect and improve the reliability and security of the nation's bulk power system through...

376

Single phase four pole/six pole motor  

DOE Patents [OSTI]

A single phase alternating current electric motor is provided with a main stator winding having two coil groups each including the series connection of three coils. These coil groups can be connected in series for six pole operation and in parallel for four pole operation. The coils are approximately equally spaced around the periphery of the machine but are not of equal numbers of turns. The two coil groups are identically wound and spaced 180 mechanical degrees apart. One coil of each group has more turns and a greater span than the other two coils. 10 figs.

Kirschbaum, H.S.

1984-10-09T23:59:59.000Z

377

DOE Fundamentals Handbook: Electrical Science, Volume 2  

SciTech Connect (OSTI)

The Electrical Science Fundamentals Handbook was developed to assist nuclear facility operating contractors provide operators, maintenance personnel, and the technical staff with the necessary fundamentals training to ensure a basic understanding terminology, and application. The handbook includes information on alternating current (AC) and direct current (DC) theory, circuits, motors, and generators; AC power and reactive components; batteries; AC and DC voltage regulators; transformers; and electrical test instruments and measuring devices. This information will provide personnel with a foundation for understanding the basic operation of various types of DOE nuclear facility electrical equipment.

Not Available

1992-06-01T23:59:59.000Z

378

Co-design of Embedded Controllers for Power Electronics and Electric Systems  

E-Print Network [OSTI]

, Electric process. I. INTRODUCTION Today, variable speed motor control systems have a wide rangeCo-design of Embedded Controllers for Power Electronics and Electric Systems Slim Ben Saoud L for the design of control systems for power electronics and electric drives. We discuss the case of a DC system

California at Irvine, University of

379

EE 341.3 (3L-3P alternate week) Electric Machines Fundamentals  

E-Print Network [OSTI]

EE 341.3 (3L-3P alternate week) Electric Machines Fundamentals Department of Electrical and Computer Engineering Fall 2014 Description: This course covers the steady-state theory of electric machines, operating characteristics, motor characteristics and speed control; DC machines-operation, efficiency, shunt

Saskatchewan, University of

380

Co-Simulation of an Electric Traction Drive Christoph Schulte and Joachim Bocker  

E-Print Network [OSTI]

Co-Simulation of an Electric Traction Drive Christoph Schulte and Joachim B¨ocker Abstract--For the simulation of electrical drives, reduced- order models or simple look-up tables are often used in order) for an electric drive, where the control structure, power electronics and motor are modeled in different environ

Paderborn, Universität

Note: This page contains sample records for the topic "4-cylinder electric motor" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


381

Department of Electrical and Computer Engineering 1982 | FAMU-FSU COLLEGE OF ENGINEERING | 2012  

E-Print Network [OSTI]

and commercially viable fuel cell. Dr. Zheng has pioneered a fuel cell technology that incorporates a thin membrane made fuel cells too expensive to be widely marketed. Dr. Zheng's technology is based on pioneering, electric vehicles and plug-in hybrid electric vehicles, electric machinery and motor drives, energy storage

Sura, Philip

382

State-of-Health Aware Optimal Control of Plug-in Electric Vehicles  

E-Print Network [OSTI]

), which utilize electric motors for propulsion, differ from fossil fuel powered vehiclesState-of-Health Aware Optimal Control of Plug-in Electric Vehicles Yanzhi Wang, Siyu Yue, USA {yanzhiwa, siyuyue, pedram}@usc.edu Abstract--Plug-in electric vehicles (PEVs) are key new energy

Pedram, Massoud

383

DSP-Based Sensor Fault-Tolerant Control of Electric Vehicle Powertrains  

E-Print Network [OSTI]

DSP-Based Sensor Fault-Tolerant Control of Electric Vehicle Powertrains Bekheïra Tabbache, Mohamed-tolerant control for a high performance induction motor drive that propels an electrical vehicle. The proposed and simulations on an electric vehicle are carried-out using a European urban and extra urban driving cycle

Brest, Université de

384

Control system and method for a hybrid electric vehicle  

DOE Patents [OSTI]

Several control methods are presented for application in a hybrid electric vehicle powertrain including in various embodiments an engine, a motor/generator, a transmission coupled at an input thereof to receive torque from the engine and the motor generator coupled to augment torque provided by the engine, an energy storage device coupled to receive energy from and provide energy to the motor/generator, an engine controller (EEC) coupled to control the engine, a transmission controller (TCM) coupled to control the transmission and a vehicle system controller (VSC) adapted to control the powertrain.

Tamor, Michael Alan (Toledo, OH)

2001-03-06T23:59:59.000Z

385

Extended Constant Power Speed Range of the Brushless DC Motor Through Dual Mode Inverter Control  

SciTech Connect (OSTI)

The trapezoidal back electromotive force (emf) brushless direct current (dc) motor (BDCM) with surface-mounted magnets has high-power density and efficiency especially when rare-earth magnet materials are used. Traction applications, such as electric vehicles, could benefit significantly from the use of such motors. Unfortunately, a practical means for driving the motor over a constant power speed ratio (CPSR) of 5:1 or more has not yet been developed. A key feature of these motors is that they have low internal inductance. The phase advance method is effective in controlling the motor power over such a speed range, but the current at high speed may be several times greater than that required at the base speed. The increase in current during high-speed operation is due to the low motor inductance and the action of the bypass diodes of the inverter. The use of such a control would require increased current rating of the inverter semiconductors and additional cooling for the inverter, where the conduction losses increase proportionally with current, and especially for the motor, where the losses increase with the square of the current. The high current problems of phase advance can be mitigated by adding series inductance; however, this reduces power density, requires significant increase in supply voltage, and leaves the CPSR performance of the system highly sensitive to variations in the available voltage. A new inverter topology and control scheme has been developed that can drive low-inductance BDCMs over the CPSR that would be required in electric vehicle applications. This new controller is called the dual-mode inverter control (DMIC). It is shown that the BDCM has an infinite CPSR when it is driven by the DMIC.

Lawler, J.S.

2000-06-23T23:59:59.000Z

386

School of Electrical & Computer Engineering -Undergraduate Post Graduate Activities Detail & History  

E-Print Network [OSTI]

& Computer Engineering - Undergraduate (continued) 2010 Employment Employer Title City State General Motors2010 School of Electrical & Computer Engineering - Undergraduate Post Graduate Activities Detail Engineering undergraduate students from the Class of 2010. Historical data is provided to allow for comparison

Lipson, Michal

387

Fact #790: July 29, 2013 States Beginning to Tax Electric Vehicles...  

Broader source: Energy.gov (indexed) [DOE]

the pump from the sale of motor fuels. Because electric vehicles (EVs) do not refuel at pumps that collect state and Federal highway taxes, they do not contribute to the upkeep of...

388

Dynein Motor Domain Shows Ring-Shaped Motor, Buttress  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr MayAtmospheric Optical Depth7-1D: Vegetation Proposed NewcatalystNeutron scattering characterizes dynamics in polymerDynein Motor Domain

389

Dynein Motor Domain Shows Ring-Shaped Motor, Buttress  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr MayAtmospheric Optical Depth7-1D: Vegetation Proposed NewcatalystNeutron scattering characterizes dynamics in polymerDynein Motor

390

Dynein Motor Domain Shows Ring-Shaped Motor, Buttress  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr MayAtmospheric Optical Depth7-1D: Vegetation Proposed NewcatalystNeutron scattering characterizes dynamics in polymerDynein MotorDynein

391

Dynein Motor Domain Shows Ring-Shaped Motor, Buttress  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May JunDatastreamsmmcrcalgovInstrumentsruc DocumentationP-Series to UserProduct:Directives Templates8.Siftingnanocrystals forDynein Motor

392

Motorization, Vehicle Purchase and Use Behavior in China: A Shanghai Survey????????????????????????????  

E-Print Network [OSTI]

49: Motorized Two-wheeler / Motorcycle Use vs. Motorized98 Table 50: Motorized Two-wheeler / Motorcycle Use vs.Motorcycle Ownership 98 Table 51: Motorized Two-

Ni, Jason

2008-01-01T23:59:59.000Z

393

Electric vehicle regenerative antiskid braking and traction control system  

DOE Patents [OSTI]

An antiskid braking and traction control system for an electric or hybrid vehicle having a regenerative braking system operatively connected to an electric traction motor, and a separate hydraulic braking system includes one or more sensors for monitoring present vehicle parameters and a processor, responsive to the sensors, for calculating vehicle parameters defining the vehicle behavior not directly measurable by the sensors and determining if regenerative antiskid braking control, requiring hydrualic braking control, or requiring traction control are required. The processor then employs a control strategy based on the determined vehicle state and provides command signals to a motor controller to control the operation of the electric traction motor and to a brake controller to control fluid pressure applied at each vehicle wheel to provide the appropriate regenerative antiskid braking control, hydraulic braking control, and traction control.

Cikanek, Susan R. (Wixom, MI)

1995-01-01T23:59:59.000Z

394

Electric vehicle regenerative antiskid braking and traction control system  

DOE Patents [OSTI]

An antiskid braking and traction control system for an electric or hybrid vehicle having a regenerative braking system operatively connected to an electric traction motor, and a separate hydraulic braking system includes one or more sensors for monitoring present vehicle parameters and a processor, responsive to the sensors, for calculating vehicle parameters defining the vehicle behavior not directly measurable by the sensors and determining if regenerative antiskid braking control, requiring hydraulic braking control, or requiring traction control are required. The processor then employs a control strategy based on the determined vehicle state and provides command signals to a motor controller to control the operation of the electric traction motor and to a brake controller to control fluid pressure applied at each vehicle wheel to provide the appropriate regenerative antiskid braking control, hydraulic braking control, and traction control. 10 figs.

Cikanek, S.R.

1995-09-12T23:59:59.000Z

395

Electrically-Assisted Turbocharger Development for Performance and Emissions  

SciTech Connect (OSTI)

Turbocharger transient lag inherently imposes a tradeoff between a robust engine response to transient load shifts and exhaust emissions. By itself, a well matched turbocharger for an engine has limited flexibility in improving this transient response. Electrically-assisted turbocharging has been seen as an attractive option to improve response and lower transient emissions. This paper presents the results of a multi-year joint CRADA between DDC and ORNL. Virtual lab diesel simulation models characterized the performance improvement potential of an electrically assisted turbocharger technology. Operating requirements to reduce transient duration between load shift time by up to 50% were determined. A turbomachine has been conceptualized with an integrated motor-generator, providing transient burst boost plus energy recovery capability. Numerous electric motor designs were considered, and a prototype motor was developed, fabricated, and is undergoing tests. Power controls have been designed and fabricated.

Bailey, Milton

2000-08-20T23:59:59.000Z

396

Combustion Tests of Rocket Motor Washout Material: Focus on Air toxics Formation Potential and Asbestos Remediation  

SciTech Connect (OSTI)

The objective of this investigation is to determine the suitability of cofiring as a recycle / reuse option to landfill disposal for solid rocket motor washout residue. Solid rocket motor washout residue (roughly 55% aluminum powder, 40% polybutadiene rubber binder, 5% residual ammonium perchlorate, and 0.2-1% asbestos) has been fired in Sandia's MultiFuel Combustor (MFC). The MFC is a down-fired combustor with electrically heated walls, capable of simulating a wide range of fuel residence times and stoichiometries. This study reports on the fate of AP-based chlorine and asbestos from the residue following combustion.

G. C. Sclippa; L. L. Baxter; S. G. Buckley

1999-02-01T23:59:59.000Z

397

Rotary steerable motor system for underground drilling  

DOE Patents [OSTI]

A preferred embodiment of a system for rotating and guiding a drill bit in an underground bore includes a drilling motor and a drive shaft coupled to drilling motor so that drill bit can be rotated by the drilling motor. The system further includes a guidance module having an actuating arm movable between an extended position wherein the actuating arm can contact a surface of the bore and thereby exert a force on the housing of the guidance module, and a retracted position.

Turner, William E. (Durham, CT); Perry, Carl A. (Middletown, CT); Wassell, Mark E. (Kingwood, TX); Barbely, Jason R. (Middletown, CT); Burgess, Daniel E. (Middletown, CT); Cobern, Martin E. (Cheshire, CT)

2010-07-27T23:59:59.000Z

398

Rotary steerable motor system for underground drilling  

DOE Patents [OSTI]

A preferred embodiment of a system for rotating and guiding a drill bit in an underground bore includes a drilling motor and a drive shaft coupled to drilling motor so that drill bit can be rotated by the drilling motor. The system further includes a guidance module having an actuating arm movable between an extended position wherein the actuating arm can contact a surface of the bore and thereby exert a force on the housing of the guidance module, and a retracted position.

Turner, William E. (Durham, CT); Perry, Carl A. (Middletown, CT); Wassell, Mark E. (Kingwood, TX); Barbely, Jason R. (Middletown, CT); Burgess, Daniel E. (Middletown, CT); Cobern, Martin E. (Cheshire, CT)

2008-06-24T23:59:59.000Z

399

System and method for determining stator winding resistance in an AC motor using motor drives  

SciTech Connect (OSTI)

A system and method for determining the stator winding resistance of AC motors is provided. The system includes an AC motor drive having an input connectable to an AC source and an output connectable to an input terminal of an AC motor, a pulse width modulation (PWM) converter having switches therein to control current flow and terminal voltages in the AC motor, and a control system connected to the PWM converter. The control system generates a command signal to cause the PWM converter to control an output of the AC motor drive corresponding to an input to the AC motor, selectively generates a modified command signal to cause the PWM converter to inject a DC signal into the output of the AC motor drive, and determines a stator winding resistance of the AC motor based on the DC signal of at least one of the voltage and current.

Lu, Bin; Habetler, Thomas G; Zhang, Pinjia

2013-02-26T23:59:59.000Z

400

-UNIT NAME C-728 Motor Cleaning Facility  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

UNIT NUMBER 33 -UNIT NAME C-728 Motor Cleaning Facility -REGULATORY STATUS--3:.:::.0:..04(--u) -LOCATION North of C-720 (Map...

Note: This page contains sample records for the topic "4-cylinder electric motor" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


401

Fluid Gravity Engineering Rocket motor flow analysis  

E-Print Network [OSTI]

Fluid Gravity Engineering Capability · Rocket motor flow analysis -Internal (performance) -External young scientists/engineers Fluid Gravity Engineering Ltd #12;

Anand, Mahesh

402

Housing assembly for electric vehicle transaxle  

DOE Patents [OSTI]

Disclosed is a drive assembly (10) for an electrically powered vehicle (12). The assembly includes a transaxle (16) having a two-speed transmission (40) and a drive axle differential (46) disposed in a unitary housing assembly (38), an oil-cooled prime mover or electric motor (14) for driving the transmission input shaft (42), an adapter assembly (24) for supporting the prime mover on the transaxle housing assembly, and a hydraulic system (172) providing pressurized oil flow for cooling and lubricating the electric motor and transaxle and for operating a clutch (84) and a brake (86) in the transmission to shift between the two-speed ratios of the transmission. The adapter assembly allows the prime mover to be supported in several positions on the transaxle housing. The brake is spring-applied and locks the transmission in its low-speed ratio should the hydraulic system fail. The hydraulic system pump is driven by an electric motor (212) independent of the prime mover and transaxle.

Kalns, Ilmars (Northville, MI)

1981-01-01T23:59:59.000Z

403

Diesel Engine Waste Heat Recovery Utilizing Electric Turbocompound Technology  

SciTech Connect (OSTI)

Caterpillar's Technology & Solutions Division conceived, designed, built and tested an electric turbocompound system for an on-highway heavy-duty truck engine. The heart of the system is a unique turbochargerr with an electric motor/generator mounted on the shaft between turbine and compressor wheels. When the power produced by the turbocharger turbine exceeds the power of the compressor, the excess power is converted to electrical power by the generator on the turbo shaft; that power is then used to help turn the crankshaft via an electric motor mounted in the engine flywheel housing. The net result is an improvement in engine fuel economy. The electric turbocompound system provides added control flexibility because it is capable of varying the amount of power extracted from the exhaust gases, thus allowing for control of engine boost. The system configuration and design, turbocharger features, control system development, and test results are presented.

Hopman, Ulrich,; Kruiswyk, Richard W.

2005-07-05T23:59:59.000Z

404

Electric Vehicles  

ScienceCinema (OSTI)

Burak Ozpineci sees a future where electric vehicles charge while we drive them down the road, thanks in part to research under way at ORNL.

Ozpineci, Burak

2014-07-23T23:59:59.000Z

405

Electric Vehicles  

SciTech Connect (OSTI)

Burak Ozpineci sees a future where electric vehicles charge while we drive them down the road, thanks in part to research under way at ORNL.

Ozpineci, Burak

2014-05-02T23:59:59.000Z

406

How to Build a Motor  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May JunDatastreamsmmcrcalgovInstrumentsruc DocumentationP-SeriesFlickr FlickrGuidedCH2MLLC HistoryVeterans |VirtualLoveApply for YourMotor

407

Aurica Motors | Open Energy Information  

Open Energy Info (EERE)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home5b9fcbce19 NoPublic Utilities Address: 160 EastMaine: Energy Resources JumpAspenAudubon, Pennsylvania:AugustaAurica Motors Jump

408

Brandl Motor | Open Energy Information  

Open Energy Info (EERE)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home5b9fcbce19 NoPublic Utilities Address: 160Benin: EnergyBoston Area Solar EnergyBradbury, California: ItBrammo MotorsportsMotor

409

AGNI Motors | Open Energy Information  

Open Energy Info (EERE)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home5b9fcbce19 NoPublic Utilities Address: 160 East 300 SouthWater Rights,Information OfOpen EnergyEnergyAGE UFMGAGNI Motors

410

Sandia National Laboratories: General Motors  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr MayAtmosphericNuclear Security Administration the1 -theErik Spoerke SSLS Exhibit at Explora MuseumFloatingFrontGTO SandiaMotors Sandia

411

Ch 16 Electric Charge &Ch 16. Electric Charge & Electric Field  

E-Print Network [OSTI]

Ch 16 Electric Charge &Ch 16. Electric Charge & Electric Field Liu UCD Phy1B 2012 #12;I Basic ConceptsI. Basic Concepts Static electricity: charges at rest Electric charge Like charges repel Unlike charges attract Liu UCD Phy1B 2012 #12;Electric ChargeElectric Charge Electron charge: -eElectron charge

Yoo, S. J. Ben

412

3.1. MOTOR SYSTEM 35 3.1 Motor System  

E-Print Network [OSTI]

3.1. MOTOR SYSTEM 35 3.1 Motor System The motor system comprises the dynamic model of the fish fish's brain. Since our goal is to animate an animal realistically and at reasonable computational cost controllers by gleaning information from the fish biomechanics literature (Blake, 1983; Alexander, 1992

Toronto, University of

413

Electric machine and current source inverter drive system  

SciTech Connect (OSTI)

A drive system includes an electric machine and a current source inverter (CSI). This integration of an electric machine and an inverter uses the machine's field excitation coil for not only flux generation in the machine but also for the CSI inductor. This integration of the two technologies, namely the U machine motor and the CSI, opens a new chapter for the component function integration instead of the traditional integration by simply placing separate machine and inverter components in the same housing. Elimination of the CSI inductor adds to the CSI volumetric reduction of the capacitors and the elimination of PMs for the motor further improve the drive system cost, weight, and volume.

Hsu, John S

2014-06-24T23:59:59.000Z

414

Electric machine  

DOE Patents [OSTI]

An interior permanent magnet electric machine is disclosed. The interior permanent magnet electric machine comprises a rotor comprising a plurality of radially placed magnets each having a proximal end and a distal end, wherein each magnet comprises a plurality of magnetic segments and at least one magnetic segment towards the distal end comprises a high resistivity magnetic material.

El-Refaie, Ayman Mohamed Fawzi (Niskayuna, NY); Reddy, Patel Bhageerath (Madison, WI)

2012-07-17T23:59:59.000Z

415

Influence of direct motor-motor interaction in models for cargo transport by a single team of motors  

E-Print Network [OSTI]

We analyze theoretically the effects of excluded-volume interactions between motors on the dynamics of a cargo driven by multiple motors. The model considered shares many commons with other recently proposed in the literature, with the addition of direct interaction between motors and motor back steps. The cargo is assumed to follow a continuum Langevin dynamics, while individual motors evolve following a Monte Carlo algorithm based on experimentally accessible probabilities for discrete forward and backward jumps, and attachment and detachment rates. The links between cargo and motors are considered as non linear springs. By means of numerical simulations we compute the relevant quantities characterizing the dynamical properties of the system, and we compare the results to those for non interacting motors. We find that interactions lead to quite relevant changes in the force-velocity relation for cargo, with a considerable reduction of the stall force, and cause also a notable decrease of the run length. These effects are mainly due to traffic-like phenomena in the microtubule. The consideration of several parallel tracks for motors reduces such effects. However, we find that for realistic values of the number of motors and the number of tracks, the influence of interactions on the global parameters of transport of cargo are far from being negligible. Our studies provide also an analysis of the relevance of motor back steps on the modeling, and of the influence of different assumptions for the detachment rates. In particular, we discuss these two aspects in connection with the possibility of observing processive back motion of cargo at large load forces.

Sebastian Bouzat; Fernando Falo

2010-12-14T23:59:59.000Z

416

Permanent magnet assisted synchronous reluctance motor, design and performance improvement  

E-Print Network [OSTI]

Recently, permanent magnet assisted (PMa)-synchronous reluctance motors (SynRM) have been considered as a possible alternative motor drive for high performance applications. In order to have an efficient motor drive, performing of three steps...

Niazi, Peyman

2006-04-12T23:59:59.000Z

417

Torquespeed relationship of the bacterial flagellar motor  

E-Print Network [OSTI]

. speed curve is derived from the usual external load torque vs. speed curve as follows. The motorspeed curve. The same physics also can explain certain puzzling properties of other motors. energy conversion external loads and gives an indication of the energy conversion efficiency. Moreover, the torque

Oster, George

418

Commercial Motor Vehicle Brake Assessment Tools  

E-Print Network [OSTI]

Commercial Motor Vehicle Brake Assessment Tools Commercial Motor Vehicle Roadside Technology to deceleration in g's ­ Passing score: BE43.5 · Enforcement tool for only 3 years. · Based solely on brake Brake Research · CMVRTC research built on these enforcement tools ­ Correlation Study ­ Level-1 / PBBT

419

Nanoconfined catalytic ngstrm-size motors  

E-Print Network [OSTI]

Chemically-powered synthetic micron and nano-scale motors that propel themselves in solution are being intensively studied because of the wide range of potential applications that exploit their directed motion. Recent experiments have shown that, even on the molecular scale, small-molecule catalysts and single enzyme molecules exhibit properties that have been attributed to self-propulsion. Simulations of very small {\\AA}ngstr\\"om-size synthetic motors in bulk solution have shown similar effects. Applications of such small motors in the cell or in microfluidic devices require knowledge of how these motors interact with boundaries. Molecular dynamics is used to investigate the properties of {\\AA}ngstr\\"om-size synthetic chemically-powered motors confined between walls separated by distances of tens of nanometers. Evidence for strong structural ordering of the motors between the walls, which reflects the finite size of solvent molecules and depends on solvent exclusion forces, is provided. Dynamical properties, such as average motor velocity, orientational relaxation and mean square displacement, are anisotropic and depend on the distance from the walls. This research presents information needed for potential applications that use these motors in the complex confined geometries encountered in biology and the laboratory.

Peter H. Colberg; Raymond Kapral

2015-01-13T23:59:59.000Z

420

Performance improvement of permanent magnet ac motors  

E-Print Network [OSTI]

.????????????????....????.. 19 B. Background............??..?????.??.?????...?.?.... 20 C. Comparing BLDC Motor and PMSM???????????... 24 D. Harmonic Spectrum of MMF in Machines with Non-sinusoidal Winding Distribution??????????????????.. 26 ix TABLE............................................................................ 58 H. Conclusion??????????????????????. 68 III FAULT TOLERANT OPERATION OF PERMANENT MAGNET MOTOR DRIVES?????????????????????? 69 A. Introduction.????????????????....???.?. 69 B. Fault Tolerant Operation of Five-Phase PMSM...

Parsa, Leila

2005-08-29T23:59:59.000Z

Note: This page contains sample records for the topic "4-cylinder electric motor" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


421

A permit is required for ALL motorized vehicles parking on the Vanderbilt University Campus. Motorcycles, motorized bicycles, motor scooters and mopeds are  

E-Print Network [OSTI]

. Motorcycles, motorized bicycles, motor scooters and mopeds are required to display "U" permits. The cost. Motorcycle, motorized bicycle, motor scooter and moped parking areas can be found on the parking map (http://www.vanderbilt.edu/parking and click on "Maps") as designated by the motorcycle symbols. Parking is authorized only in spaces marked

Simaan, Nabil

422

Insulation assembly for electric machine  

SciTech Connect (OSTI)

An insulation assembly is provided that includes a generally annularly-shaped main body and at least two spaced-apart fingers extending radially inwards from the main body. The spaced-apart fingers define a gap between the fingers. A slot liner may be inserted within the gap. The main body may include a plurality of circumferentially distributed segments. Each one of the plurality of segments may be operatively connected to another of the plurality of segments to form the continuous main body. The slot liner may be formed as a single extruded piece defining a plurality of cavities. A plurality of conductors (extendable from the stator assembly) may be axially inserted within a respective one of the plurality of cavities. The insulation assembly electrically isolates the conductors in the electric motor from the stator stack and from other conductors.

Rhoads, Frederick W.; Titmuss, David F.; Parish, Harold; Campbell, John D.

2013-10-15T23:59:59.000Z

423

Integrated Vehicle Thermal Management - Combining Fluid Loops in Electric Drive Vehicles (Presentation)  

SciTech Connect (OSTI)

Plug-in hybrid electric vehicles and electric vehicles have increased vehicle thermal management complexity, using separate coolant loop for advanced power electronics and electric motors. Additional thermal components result in higher costs. Multiple cooling loops lead to reduced range due to increased weight. Energy is required to meet thermal requirements. This presentation for the 2013 Annual Merit Review discusses integrated vehicle thermal management by combining fluid loops in electric drive vehicles.

Rugh, J. P.

2013-07-01T23:59:59.000Z

424

axial motor circuits: Topics by E-print Network  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Fundamentals of electromechanical energy conversion. Motors and generators, transformers, single and three- phase power circuits, three-phase induction motor including...

425

Improving Motor and Drive System Performance: A Sourcebook for Industry  

SciTech Connect (OSTI)

This is one in a series of sourcebooks to assist industrial personnel in understanding and optimizing motors and motor-driven systems

Not Available

2008-09-01T23:59:59.000Z

426

United States Industrial Motor-Driven Systems Market Assessment...  

Broader source: Energy.gov (indexed) [DOE]

Motor-Driven Systems Market Assessment: Charting a Roadmap to Energy Savings for Industry United States Industrial Motor-Driven Systems Market Assessment: Charting a Roadmap to...

427

Improving Motor and Drive System Performance - A Sourcebook for...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

motors and drives, as well as resources for additional information, tools, software, videos, and training opportunities. Improving Motor and Drive System Performance - A...

428

New rocket propellant and motor design offer high-performance...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

New rocket propellant and motor design offer high-performance and safety New rocket propellant and motor design offer high-performance and safety Scientists recently flight tested...

429

Premium Efficiency Motor Selection and Application Guide - A...  

Broader source: Energy.gov (indexed) [DOE]

handbook informs new motor purchase decisions by identifying energy and cost savings that can come from replacing motors with premium efficiency units. The handbook provides an...

430

Best Practices in Non-Motorized Transport Planning, Implementation...  

Open Energy Info (EERE)

Motorized Transport Planning, Implementation and Maintenance Jump to: navigation, search Tool Summary LAUNCH TOOL Name: Best Practices in Non-Motorized Transport Planning,...

431

Carbonyl Emissions from Gasoline and Diesel Motor Vehicles  

E-Print Network [OSTI]

fraction of light-duty gasoline vehicle particulate matterQuinone emissions from gasoline and diesel motor vehicles.32 organic compounds from gasoline- powered motor vehicles.

Jakober, Chris A.

2008-01-01T23:59:59.000Z

432

Electrical connector  

DOE Patents [OSTI]

An electrical connector includes a female component having one or more receptacles, a first test receptacle, and a second test receptacle. The electrical connector also includes a male component having one or more terminals configured to engage the one or more receptacles, a first test pin configured to engage the first test receptacle, and a second test pin configured to engage the second test receptacle. The first test receptacle is electrically connected to the second test receptacle, and at least one of the first test pin and the second test pin is shorter in length than the one or more terminals.

Dilliner, Jennifer L.; Baker, Thomas M.; Akasam, Sivaprasad; Hoff, Brian D.

2006-11-21T23:59:59.000Z

433

36 IEEE TRANSACTIONS ON INDUSTRY APPLICATIONS, VOL. 35, NO. 1, JANUARY/FEBRUARY 1999 Multilevel Converters for Large Electric Drives  

E-Print Network [OSTI]

Converters for Large Electric Drives Leon M. Tolbert, Senior Member, IEEE, Fang Zheng Peng, Senior Member multilevel con- verters as an application for high-power and/or high-voltage electric motor drives all-electric drives because it uses several levels of dc voltage sources, which would be available

Tolbert, Leon M.

434

Proceedings of the 2008 International Conference on Electrical Machines Paper ID 1436 Comparative Analysis of Estimation Techniques  

E-Print Network [OSTI]

is a prevailing design of electric drive for EVs. Drives Efficiency is crucial to saving energy and offering moreProceedings of the 2008 International Conference on Electrical Machines Paper ID 1436 Comparative Analysis of Estimation Techniques of SFOC Induction Motor for Electric Vehicles A. Haddoun1,2 , M

Paris-Sud XI, Université de

435

Engineering Electrical &  

E-Print Network [OSTI]

Computer Engineering Electrical & Electronic Engineering Mechatronics Engineering Mechanical Engineering Civil Engineering Natural Resources Engineering Forest Engineering Chemical & Process Engineering ELECTIVE 2 Required Engineering Intermediate Year 2011 Eight Required Courses Chart: 120 points College

Hickman, Mark

436

Engineering Electrical &  

E-Print Network [OSTI]

Computer Engineering Electrical & Electronic Engineering Mechatronics Engineering Mechanical Engineering Civil Engineering Natural Resources Engineering Forest Engineering Chemical & Process Engineering ELECTIVE 2 Required Engineering Intermediate Year 2012 Eight Required Courses Chart: 120 points College

Hickman, Mark

437

Exchange-Spring Magnets: Nanocomposite Exchange-Spring Magnets for Motor and Generator Applications  

SciTech Connect (OSTI)

REACT Project: ANL will develop a cost-effective exchange-spring magnet to use in the electric motors of wind generators and EVs that uses no rare earth materials. This ANL exchange-spring magnet combines a hard magnetic outer shell with a soft magnetic inner corecoupling these together increases the performance (energy density and operating temperature). The hard and soft magnet composite particles would be created at the molecular level, followed by consolidation in a magnetic field. This process allows the particles to be oriented to maximize the magnetic properties of low-cost and abundant metals, eliminating the need for expensive imported rare earths. The ultimate goal of this project is to demonstrate this new type of magnet in a prototype electric motor.

None

2012-01-01T23:59:59.000Z

438

Electric vehicles move closer to market  

SciTech Connect (OSTI)

This article reports that though battery technology is currently limiting the growth of EVs, the search for improvements is spurring innovative engineering developments. As battery makers, automakers, national laboratories, and others continue their search for a practical source of electric power that will make electric vehicles (EVs) more viable, engineers worldwide are making progress in other areas of EV development. Vector control, for example, enables better regulation of motor torque and speed; composite and aluminum parts reduce the vehicle`s weight, which in turn reduces the load on the motor and battery; and flywheel energy storage systems, supercapacitors, regenerative brake systems, and hybrid/electric drive trains increase range and acceleration. Despite efforts to develop an electric vehicle from the ground up, most of the early EVs to be sold in the United States will likely be converted from gasoline-powered vehicles. Chrysler Corp., for example, is expected to sell electric versions of its minivans and build them on the same assembly line as its gasoline-powered vehicles to reduce costs. The pace of engineering development in this field is fast and furious. Indeed, it is virtually impossible to monitor all emerging EV technology. To meet their quotas, the major automakers may even consider buying credits from smaller, innovative EV manufacturers. But whatever stopgap measures vehicle makers take, technology development will be the driving force behind long-term EV growth.

O`Connor, L.

1995-03-01T23:59:59.000Z

439

Integrated Inverter For Driving Multiple Electric Machines  

DOE Patents [OSTI]

An electric machine drive (50) has a plurality of inverters (50a, 50b) for controlling respective electric machines (57, 62), which may include a three-phase main traction machine (57) and two-phase accessory machines (62) in a hybrid or electric vehicle. The drive (50) has a common control section (53, 54) for controlling the plurality of inverters (50a, 50b) with only one microelectronic processor (54) for controlling the plurality of inverters (50a, 50b), only one gate driver circuit (53) for controlling conduction of semiconductor switches (S1-S10) in the plurality of inverters (50a, 50b), and also includes a common dc bus (70), a common dc bus filtering capacitor (C1) and a common dc bus voltage sensor (67). The electric machines (57, 62) may be synchronous machines, induction machines, or PM machines and may be operated in a motoring mode or a generating mode.

Su, Gui-Jia [Knoxville, TN; Hsu, John S [Oak Ridge, TN

2006-04-04T23:59:59.000Z

440

Optimization of induction motor efficiency. Volume 3. Experimental comparison of three-phase standard motors with Wanlass motors. Final report  

SciTech Connect (OSTI)

Researchers conducted comprehensive laboratory tests to evaluate the effectiveness of the Wanlass connection in improving motor efficiency. On the basis of these tests, they found no reason to conclude that such a connection is more efficient than the standard connection.

Fuchs, E.F.

1985-12-01T23:59:59.000Z

Note: This page contains sample records for the topic "4-cylinder electric motor" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


441

Electric vehicle drive train with rollback detection and compensation  

DOE Patents [OSTI]

An electric vehicle drive train includes a controller for detecting and compensating for vehicle rollback, as when the vehicle is started upward on an incline. The vehicle includes an electric motor rotatable in opposite directions corresponding to opposite directions of vehicle movement. A gear selector permits the driver to select an intended or desired direction of vehicle movement. If a speed and rotational sensor associated with the motor indicates vehicle movement opposite to the intended direction of vehicle movement, the motor is driven to a torque output magnitude as a nonconstant function of the rollback speed to counteract the vehicle rollback. The torque function may be either a linear function of speed or a function of the speed squared.

Konrad, Charles E. (Roanoke, VA)

1994-01-01T23:59:59.000Z

442

Electric vehicle drive train with rollback detection and compensation  

DOE Patents [OSTI]

An electric vehicle drive train includes a controller for detecting and compensating for vehicle rollback, as when the vehicle is started upward on an incline. The vehicle includes an electric motor rotatable in opposite directions corresponding to opposite directions of vehicle movement. A gear selector permits the driver to select an intended or desired direction of vehicle movement. If a speed and rotational sensor associated with the motor indicates vehicle movement opposite to the intended direction of vehicle movement, the motor is driven to a torque output magnitude as a nonconstant function of the rollback speed to counteract the vehicle rollback. The torque function may be either a linear function of speed or a function of the speed squared. 6 figures.

Konrad, C.E.

1994-12-27T23:59:59.000Z

443

Electrical & Computer Engineering S E M I N A R  

E-Print Network [OSTI]

. It will have delta wings which fold up in driving mode. The vehicle will be driven by an electric motor, direct-drive wheels, a lifting-body airframe, low-power VTOL technology, and dual-use vehicle componentsElectrical & Computer Engineering S E M I N A R L o u i s i a n a S t a t e U n i v e r s i t y

Koppelman, David M.

444

Synchronous motor with soft start element formed between the motor rotor and motor output shaft to successfully synchronize loads that have high inertia and/or high torque  

DOE Patents [OSTI]

A line-start synchronous motor has a housing, a rotor shaft, and an output shaft. A soft-start coupling portion is operatively coupled to the output shaft and the rotor shaft. The soft-start coupling portion is configurable to enable the synchronous motor to obtain synchronous operation and to drive, at least near synchronous speed during normal steady state operation of the motor, a load having characteristics sufficient to prevent obtaining normal synchronous operation of the motor when the motor is operatively connected to the load in the absence of the soft-start coupling. The synchronous motor is sufficiently rated to obtain synchronous operation and to drive, at least near synchronous speed during normal steady state operation of the motor, a load having characteristics sufficient to prevent obtaining normal synchronous operation of the motor when the motor is operatively connected to the load in the absence of the soft-start coupling.

Umans, Stephen D; Nisley, Donald L; Melfi, Michael J

2014-10-28T23:59:59.000Z

445

Convective Cooling and Passive Stack Improvements in Motors (Presentation)  

SciTech Connect (OSTI)

This presentation discusses current research at NREL in convective cooling and passive stack improvements in motors.

Bennion, K.

2014-06-01T23:59:59.000Z

446

A rotating suspended liquid film as an electric generator  

E-Print Network [OSTI]

We have observed that a rotating liquid film generates electricity when a large external electric field is applied in the plane of the film. In our experiment suspended liquid film (soap film) is formed on a circular frame positioned horizontally on a rotating motor. This devise is located at the center of two capacitor-like vertical plates to apply external electric field in X-direction.The produced electric energy is piked up by two brushes in Y-direction of the suspended liquid film. We previously reported that a liquid film in an external electric field rotates when an electric current passes through it, naming it the liquid film motor (LFM). In this letter we report that the same system can be used as an electric generator, converting the rotating mechanical energy to an electric energy. The liquid film electric generator (LFEG) is in stark contrast to the LFM, both of which could be designed in very small scales like micro scales applicable in lab on a chip. The device is comparable to commercial DC ele...

Amjadi, Ahmad; Namin, Reza Montazeri

2013-01-01T23:59:59.000Z

447

SENSORLESS INDUCTION MOTOR CONTROL USING STATISTICAL  

E-Print Network [OSTI]

is replaced by npM so that the dynamic model of the induction motor is then uSa = RSiSa + LS d dtiSa + M d dti

448

Energy Savings of Variable Speed Motors  

E-Print Network [OSTI]

This paper investigates the energy savings available by utilizing variable speed motors on pump and fan applications. Conventional control of flow or pressure in process plants is normally accomplished by throttling the various streams with control...

Fishel, F. D.

1979-01-01T23:59:59.000Z

449

Method and apparatus for large motor control  

DOE Patents [OSTI]

Apparatus and method for providing digital signal processing method for controlling the speed and phase of a motor involves inputting a reference signal having a frequency and relative phase indicative of a time based signal; modifying the reference signal to introduce a slew-rate limited portion of each cycle of the reference signal; inputting a feedback signal having a frequency and relative phase indicative of the operation of said motor; modifying the feedback signal to introduce a slew-rate limited portion of each cycle of the feedback signal; analyzing the modified reference signal and the modified feedback signal to determine the frequency of the modified reference signal and of the modified feedback signal and said relative phase between said modified reference signal and said modified feedback signal; and outputting control signals to the motor for adjusting said speed and phase of the motor based on the frequency determination and determination of the relative phase.

Rose, Chris R. (Santa Fe, NM); Nelson, Ronald O. (White Rock, NM)

2003-08-12T23:59:59.000Z

450

Total Energy Management in General Motors  

E-Print Network [OSTI]

This paper presents an overview of General Motors' energy management program with special emphasis on energy conservation. Included is a description of the total program organization, plant guidelines, communication and motivation techniques...

DeKoker, N.

1979-01-01T23:59:59.000Z

451

Control of Surface Mounted Permanent Magnet Motors with Special Application to Fractional-Slot Motors with Concentrated Windings  

SciTech Connect (OSTI)

A 30 pole, 6 kW, and 6000 maximum revolutions per minute (rpm) prototype of the permanent magnet synchronous motor (PMSM) with fractional-slot concentrated windings (FSCW) has been designed, built, and tested at the University of Wisconsin at Madison (UWM). This machine has significantly more inductance than that of regular PMSMs. The prototype was delivered in April 2006 to the Oak Ridge National Laboratory (ORNL) for testing and development of a controller that will achieve maximum efficiency. In advance of the test/control development effort, ORNL has used the PMSM models developed over a number of previous studies to study how steady state performance of high inductance PMSM machines relates to control issues. This report documents the results of this research. The amount of inductance that enables the motor to achieve infinite constant power speed ratio (CPSR) is given by L{sub {infinity}} = E{sub b}/{Omega}{sub b}I{sub R}, where E{sub b} is the root-mean square (rms) magnitude of the line-to-neutral back-electromotive force (emf) at base speed, {Omega}{sub b} is the base speed in electrical radians per second, and I{sub R} is the rms current rating of the motor windings. The prototype machine that was delivered to ORNL has about 1.5 times as much inductance as a typical PMSM with distributed integral slot windings. The inventors of the FSCW method, who designed the prototype machine, remarked that they were 'too successful' in incorporating inductance into their machine and that steps would be taken to modify the design methodology to reduce the inductance to the optimum value. This study shows a significant advantage of having the higher inductance rather than the optimal value because it enables the motor to develop the required power at lower current thereby reducing motor and inverter losses and improving efficiency. The main problem found with high inductance machines driven by a conventional phase advance (CPA) method is that the motor current at high speed depends solely on machine parameters and is virtually independent of the load level and the direct current (dc) supply voltage. Thus, the motor current is virtually the same at no load as at full load resulting in poor efficiency at less than full load conditions. While an inductance higher than the value cited above is warranted, it still does not ensure that the motor current is proportional to load; consequently, the problem of low efficiency at high speed and partial load is not resolved but is only mitigated. A common definition of 'base speed' is the speed at which the voltage applied to the motor armature is equal to the magnitude of the back-emf. The results in this study indicate that the dc supply voltage should be adequate to drive rated current into the motor winding at the specified base speed. At a minimum this requires sufficient voltage to overcome not only the back-emf but also the voltage drop across the internal impedance of the machine. For a high inductance PMSM, the internal impedance at base speed can be considerable and substantial additional voltage is required to overcome the internal voltage drop. It is further shown that even more voltage than the minimum required for injecting rated current at base speed can be beneficial by allowing the required power to be developed at lower current, which reduces losses in the motor and inverter components. Further, it is shown that the current is minimized at a unique speed; consequently, there may be room for optimization if the drive spends a substantial amount of its operating life at a certain speed (for example 60 mph). In this study, fundamental frequency phasor models are developed for a synchronous PMSM and the control systems that drive them is CPA. The models were compared with detailed simulations to show their validity. The result was used to design a traction drive control system with optimized efficiency to drive the fractional-slot motor with concentrated windings. The goal is to meet or exceed the FreedomCAR inverter cost and performance targets.

McKeever, John W [ORNL; Patil, Niranjan [University of Tennessee, Knoxville (UTK); Lawler, Jack [ORNL

2007-07-01T23:59:59.000Z

452

Aptera Motors | Open Energy Information  

Open Energy Info (EERE)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Office of InspectorConcentrating SolarElectricEnergyCT Biomass Facility JumpvolcanicPhase

453

Six pole/eight pole single-phase motor  

DOE Patents [OSTI]

A single phase alternating current electric motor is provided with a main stator winding having two coil groups which are connected to form eight poles for eight-pole operation and to form six poles for six-pole operation. Each group contains four series connected coil elements with each element spanning approximately one-seventh of the periphery of the machine. The coil groups are spaced 180 mechanical degrees apart such that each end coil of one group overlaps one of the end coils of the other group. An auxiliary stator winding having two coil groups with the same relative angular displacement as the main stator winding coil groups is included. 10 figs.

Kirschbaum, H.S.

1984-07-31T23:59:59.000Z

454

Boost Converters for Gas Electric and Fuel Cell Hybrid Electric Vehicles  

SciTech Connect (OSTI)

Hybrid electric vehicles (HEVs) are driven by at least two prime energy sources, such as an internal combustion engine (ICE) and propulsion battery. For a series HEV configuration, the ICE drives only a generator, which maintains the state-of-charge (SOC) of propulsion and accessory batteries and drives the electric traction motor. For a parallel HEV configuration, the ICE is mechanically connected to directly drive the wheels as well as the generator, which likewise maintains the SOC of propulsion and accessory batteries and drives the electric traction motor. Today the prime energy source is an ICE; tomorrow it will very likely be a fuel cell (FC). Use of the FC eliminates a direct drive capability accentuating the importance of the battery charge and discharge systems. In both systems, the electric traction motor may use the voltage directly from the batteries or from a boost converter that raises the voltage. If low battery voltage is used directly, some special control circuitry, such as dual mode inverter control (DMIC) which adds a small cost, is necessary to drive the electric motor above base speed. If high voltage is chosen for more efficient motor operation or for high speed operation, the propulsion battery voltage must be raised, which would require some type of two-quadrant bidirectional chopper with an additional cost. Two common direct current (dc)-to-dc converters are: (1) the transformer-based boost or buck converter, which inverts a dc voltage, feeds the resulting alternating current (ac) into a transformer to raise or lower the voltage, and rectifies it to complete the conversion; and (2) the inductor-based switch mode boost or buck converter [1]. The switch-mode boost and buck features are discussed in this report as they operate in a bi-directional chopper. A benefit of the transformer-based boost converter is that it isolates the high voltage from the low voltage. Usually the transformer is large, further increasing the cost. A useful feature of the switch mode boost converter is its simplicity. Its inductor must handle the entire current, which is responsible for its main cost. The new Z-source inverter technology [2,3] boosts voltage directly by actively using the zero state time to boost the voltage. In the traditional pulse width modulated (PWM) inverter, this time is used only to control the average voltage by disconnecting the supply voltage from the motor. The purpose of this study is to examine the Z-source's potential for reducing the cost and improving the reliability of HEVs.

McKeever, JW

2005-06-16T23:59:59.000Z

455

Power factor correction of an electrical drive system based on multiphase machines  

E-Print Network [OSTI]

Power factor correction of an electrical drive system based on multiphase machines Khoudir MAROUANI_tabache@yahoo.com Abstract--This paper deals with the energy efficiency improvement of an electrical drive which can be used both in wind energy conversion or motor drive applications. A power factor (PF) control scheme

Paris-Sud XI, Université de

456

A Development of Design and Control Methodology for Next Generation Parallel Hybrid Electric Vehicle  

E-Print Network [OSTI]

combustion engine in the HEV, and uses the electrical drive to compensate for the power gap between the load demand and the engine capacity. Unfortunately, the low power density and the high cost of the combined electric motor drive and battery packs dictate...

Lai, Lin

2013-01-28T23:59:59.000Z

457

DSP Based Ultracapacitor System for Hybrid-Electric Vehicles Juan W. Dixon  

E-Print Network [OSTI]

DSP Based Ultracapacitor System for Hybrid-Electric Vehicles Juan W. Dixon Department of Electrical vehicles has been implemented and tested successfully. The system can work with different primary power the vehicle with minimum help of the primary power source. The vehicle uses a brushless dc motor

Catholic University of Chile (Universidad Católica de Chile)

458

Equivalent Circuit Modeling of Hysteresis Motors  

SciTech Connect (OSTI)

We performed a literature review and found that many equivalent circuit models of hysteresis motors in use today are incorrect. The model by Miyairi and Kataoka (1965) is the correct one. We extended the model by transforming it to quadrature coordinates, amenable to circuit or digital simulation. 'Hunting' is an oscillatory phenomenon often observed in hysteresis motors. While several works have attempted to model the phenomenon with some partial success, we present a new complete model that predicts hunting from first principles.

Nitao, J J; Scharlemann, E T; Kirkendall, B A

2009-08-31T23:59:59.000Z

459

Direct-drive field actuator motors  

DOE Patents [OSTI]

A high-torque, low speed, positive-drive field actuator motor is disclosed including a stator carrying at least one field actuator which changes in dimension responsive to application of an energy field, and at least one drive shoe movable by the dimensional changes of the field actuator to contact and move a rotor element with respect to the stator. Various embodiments of the motor are disclosed, and the rotor element may be moved linearly or arcuately. 37 figs.

Grahn, A.R.

1995-07-11T23:59:59.000Z

460

Electrical hazards  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr MayAtmospheric Optical Depth7-1D: Vegetation Proposed NewcatalystNeutronEnvironmentZIRKLEEFFECTS OFElaineElectric826Lab Electrical6,

Note: This page contains sample records for the topic "4-cylinder electric motor" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


461

Power applications of high-temperature superconductivity: Variable speed motors, current switches, and energy storage for end use  

SciTech Connect (OSTI)

The objective of this project is to conduct joint research and development activities related to certain electric power applications of high-temperature superconductivity (HTS). The new superconductors may allow development of an energy-efficient switch to control current to variable speed motors, superconducting magnetic energy storage (SMES) systems, and other power conversion equipment. Motor types that were considered include induction, permanent magnet, and superconducting ac motors. Because it is impractical to experimentally alter certain key design elements in radial-gap motors, experiments were conducted on an axial field superconducting motor prototype using 4 NbTi magnets. Superconducting magnetic energy storage technology with 0.25--5 kWh stored energy was studied as a viable solution to short duration voltage sag problems on the customer side of the electric meter. The technical performance characteristics of the device wee assembled, along with competing technologies such as active power line conditioners with storage, battery-based uninterruptible power supplies, and supercapacitors, and the market potential for SMES was defined. Four reports were prepared summarizing the results of the project.

Hawsey, R.A. [Oak Ridge National Lab., TN (United States); Banerjee, B.B.; Grant, P.M. [Electric Power Research Inst., Palo Alto, CA (United States)

1996-08-01T23:59:59.000Z

462

ELECTRICAL & INFORMATION  

E-Print Network [OSTI]

focuses on. Smart Grids: Electricity networks are designed to transport energy from where of energy and smarter management of the system. These are called Smart Grids. A number of research projects in medical informatics, smart cities, mining, energy, financial systems, etc. Bioinformatics

Wagner, Stephan

463

Electric top drives gain wide industry acceptance  

SciTech Connect (OSTI)

Since its introduction, the top drive drilling system has gained acceptance as a productive and safe method for drilling oil and gas wells. Originally, the system was used mostly for offshore and higher cost land drilling, and it had to be installed as a permanent installation because of its enormous weight and size. Essentially, a top drive replaces the kelly and rotary table as the means of rotating drillpipe on oil, gas and geothermal rigs and is considered to be 15% to 40% more efficient than a kelly drive. Top drive systems allow the operator to drill and maintain directional orientation for triple stands and provide tripping efficiency because of the ability to ream and circulate with triple stands, to reduce the risk of stuck pipe or lost wells, and to improve well control and pipe handling safety. The paper describes electric top drives with DC motors, top drives with AC motors, top drives with permanent magnet motors, and top drives with permanent magnet brushless synchronous motors.

Riahi, M.L.

1998-05-01T23:59:59.000Z

464

Tesla Motors | Open Energy Information  

Open Energy Info (EERE)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Office of InspectorConcentrating SolarElectric Coop, Inc Place:Innovation & SolutionsKentucky) Jump to:TernionTesla

465

LABORATORY II ELECTRIC FIELDS AND ELECTRIC POTENTIALS  

E-Print Network [OSTI]

Lab II - 1 LABORATORY II ELECTRIC FIELDS AND ELECTRIC POTENTIALS In this lab you will continue to investigate the abstract concept of electric field. If you know the electric field at a point in space, you). With this simulation you can construct a complicated charge configuration and read out the resulting electric field

Minnesota, University of

466

Electrical and Computer Engineering Electrical Engineering  

E-Print Network [OSTI]

Electrical and Computer Engineering Electrical Engineering Department Website: www.iit.edu/engineering/ece Electrical engineering is concerned with the generation, transmission, and utilization of electrical energy and with the transmitting and processing of information. Electrical engineers are involved in the analysis, design, and pro

Heller, Barbara

467

Electrical Safety Committee Charter  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

ANL Electrical Safety Page DOE Electrical Safety Handbook General Statement Home & Office Equipment Statement APS Electrical Safety Update Guidelines for Working on Voltages < 240...

468

High Temperatures & Electricity Demand  

E-Print Network [OSTI]

High Temperatures & Electricity Demand An Assessment of Supply Adequacy in California Trends.......................................................................................................1 HIGH TEMPERATURES AND ELECTRICITY DEMAND.....................................................................................................................7 SECTION I: HIGH TEMPERATURES AND ELECTRICITY DEMAND ..........................9 BACKGROUND

469

E-Print Network 3.0 - advanced ac motor Sample Search Results  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

for a QE2 synchronous motor... in motor applications < 110 the energy required for 4K refrigeration HTS enhances commercial economics... Motors and Generators HTS enables...

470

Impact of California Reformulated Gasoline On Motor Vehicle Emissions. 1. Mass Emission Rates  

E-Print Network [OSTI]

California reformulated gasoline on motor vehicle emissions.Impact of California Reformulated Gasoline OIl Motor Vehicleprogress, increased vehicle Gasoline Motor on Vehicle travel

Kirchstetter, Thomas W.; Singer, Brett C.; Harley, Robert A.

1999-01-01T23:59:59.000Z

471

Force-velocity relations for multiple molecular motor transportation  

E-Print Network [OSTI]

A transition rate model of cargo transportation by N effective molecular motors is proposed. Under the assumption of steady state, the force-velocity curve of multi-motor system can be derived from the force-velocity curve of single motor. Our work shows, in the case of low load, the velocity of multi-motor system can decrease or increase with increasing motor number, which is dependent on the single motor force-velocity curve. And most commonly, the velocity decreases. This gives a possible explanation to some recent experimental observations.

Wang, Ziqing

2009-01-01T23:59:59.000Z

472

Force-velocity relations for multiple-molecular-motor transport  

E-Print Network [OSTI]

A transition rate model of cargo transport by $N$ molecular motors is proposed. Under the assumption of steady state, the force-velocity curve of multi-motor system can be derived from the force-velocity curve of single motor. Our work shows, in the case of low load, the velocity of multi-motor system can decrease or increase with increasing motor number, which is dependent on the single motor force-velocity curve. And most commonly, the velocity decreases. This gives a possible explanation to some recent

Ziqing Wang; Ming Li

2009-10-01T23:59:59.000Z

473

Raft River Rural Electric Coop. Vigilante Electric Coop. Northern  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Farmers Electric Riverside Electric Minidoka Soda Springs Idaho Falls Lower Valley Energy Lost River Electric Coop. Fall River Rural Electric Coop. Salmon River Electric...

474

Electrical system architecture having high voltage bus  

DOE Patents [OSTI]

An electrical system architecture is disclosed. The architecture has a power source configured to generate a first power, and a first bus configured to receive the first power from the power source. The architecture also has a converter configured to receive the first power from the first bus and convert the first power to a second power, wherein a voltage of the second power is greater than a voltage of the first power, and a second bus configured to receive the second power from the converter. The architecture further has a power storage device configured to receive the second power from the second bus and deliver the second power to the second bus, a propulsion motor configured to receive the second power from the second bus, and an accessory motor configured to receive the second power from the second bus.

Hoff, Brian Douglas (East Peoria, IL); Akasam, Sivaprasad (Peoria, IL)

2011-03-22T23:59:59.000Z

475

Illinois Municipal Electric Agency- Electric Efficiency Program  

Broader source: Energy.gov [DOE]

The Illinois Municipal Electric Agency (IMEA) offers rebates to member municipal utilities* (those who purchase wholesale electric service from IMEA) and retail customers for energy efficiency...

476

Severe environment turbine powered steerable motors  

SciTech Connect (OSTI)

Turbine powered downhole motors have advantages for high temperature, high pressure, sour gas or hard formation drilling which stem from turbodrill construction rather than metallurgy, and from their power characteristics. The first part of the paper will discuss this, and compare turbine and Moineau powered motors in this context. The introduction in the last three years of new bearing materials, hydraulic thrust balancing devices and high performance flexible couplings have extended turbodrill performance and reliability margins in severe environment drilling. It is perfecting feasible to build steerable motors capable of drilling for 250 hours in 6-in. hole at 200 degrees Celsius (392 degrees Fahrenheit) in a deviated high pressure well since the individual problems in this ``Well from Hell`` have successfully been overcome. The second part of the paper will illustrate this through field examples.

Gaynor, T.M. [Neyrfor-Weir Ltd., Aberdeen (United Kingdom). Dept. of Operations

1995-12-31T23:59:59.000Z

477

912 IEEE TRANSACTIONS ON INDUSTRY APPLICATIONS, VOL. 47, NO. 2, MARCH/APRIL 2011 Impact of SiC Devices on Hybrid Electric and  

E-Print Network [OSTI]

; in particular, the size of the battery bank can be reduced for optimum design. Index Terms--Efficiency, hybrid (SiC) devices as battery interface, motor controller, etc., in a hybrid electric vehicle (HEV][5]. The application of SiC devices (as battery interface, motor controller, etc.) in a HEV has merit because

Tolbert, Leon M.

478

Evaluation of a Current Source Active Power Filter to Reduce the DC Bus Capacitor in a Hybrid Electric Vehicle Traction Drive  

E-Print Network [OSTI]

system, additional heat, audible noise, mechanical stress, and vibration [1]. DC bus harmonic current- powered three-phase inverter is used to drive the traction motor. Due to the switching behavior combustion engine, electric motor, and energy storage device (for example, batteries and ultracapacitors

Tolbert, Leon M.

479

ELECTRICAL ENGINEERING EECS Department  

E-Print Network [OSTI]

ELECTRICAL ENGINEERING EECS Department The Electrical Engineering and Computer Science (EECS) Department at WSU offers undergraduate degrees in electrical engineering, computer engineering and computer science. The EECS Department offers master of science degrees in computer science, electrical engineering

480

Renewable Electricity Futures Study  

E-Print Network [OSTI]

Renewable Electricity Futures Study Renewable Electricity Generation and Storage Technologies for Sustainable Energy, LLC. #12;Renewable Electricity Futures Study Edited By Hand, M.M. National Renewable;Suggested Citations Renewable Electricity Futures Study (Entire Report) National Renewable Energy Laboratory

Note: This page contains sample records for the topic "4-cylinder electric motor" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


481

Soft-commutated direct current motor  

DOE Patents [OSTI]

A method and circuit is disclosed for soft-commutation of a direct current (DC) motor. An attenuation circuit is connected through auxiliary brushes A, A[prime], B and B[prime] to the commutator (16) to drain circuit from successive armature coils (15) before the main brushes (27, 28) disconnects from each of the coils (15). This prevents the spark generation that normally occurs in conventional DC motors. The attenuation circuit may also be connected before energization of the coil (15) for a soft turning on operation. 13 figs.

Hsu, J.S.

1999-07-27T23:59:59.000Z

482

Electrical receptacle  

DOE Patents [OSTI]

The invention is a receptacle for a three prong electrical plug which has either a tubular or U-shaped grounding prong. The inventive receptacle has a grounding prong socket which is sufficiently spacious to prevent the socket from significantly stretching when a larger, U-shaped grounding prong is inserted into the socket, and having two ridges to allow a snug fit when a smaller tubular shape grounding prong is inserted into the socket. The two ridges are made to prevent the socket from expanding when either the U-shaped grounding prong or the tubular grounding prong is inserted.

Leong, R.

1993-06-22T23:59:59.000Z

483

Method and system for managing an electrical output of a turbogenerator  

DOE Patents [OSTI]

The system and method manages an electrical output of a turbogenerator in accordance with multiple modes. In a first mode, a direct current (DC) bus receives power from a turbogenerator output via a rectifier where turbogenerator revolutions per unit time (e.g., revolutions per minute (RPM)) or an electrical output level of a turbogenerator output meet or exceed a minimum threshold. In a second mode, if the turbogenerator revolutions per unit time or electrical output level of a turbogenerator output are less than the minimum threshold, the electric drive motor or a generator mechanically powered by the engine provides electrical energy to the direct current bus.

Stahlhut, Ronnie Dean (Bettendorf, IA); Vuk, Carl Thomas (Denver, IA)

2010-08-24T23:59:59.000Z

484

Electrical installations in oil shale mines. Open file report 21 Sep 81-13 Aug 83  

SciTech Connect (OSTI)

This report presents recommended guidelines and regulatory changes applicable to electrical installations in underground oil shale mines. These recommendations are based on information gathered from oil shale operators, government agencies, and other knowledgeable sources familiar with existing plans for mining systems and electrical installations, and on present understanding of the problems and hazards associated with oil shale mining. Additional discussions of specific electrical problems related to oil shale mining include ground fault current levels, permissible electric wheel motors, permissible batteries and electric starting systems, intrinsically safe instrumentation, and applicability of existing test standards.

Gillenwater, B.B.; Kline, R.J.; Paas, N.

1983-08-01T23:59:59.000Z

485

Modeling Reluctance-Assisted PM Motors  

SciTech Connect (OSTI)

This report contains a derivation of the fundamental equations used to calculate the base speed, torque delivery, and power output of a reluctance-assisted PM motor which has a saliency ratio greater than 1 as a function of its terminal voltage, current, voltage-phase angle, and current-phase angle. The equations are applied to model Motor X using symbolically-oriented methods with the computer tool Mathematica to determine: (1) the values of current-phase angle and voltage-phase angle that are uniquely determined once a base speed has been selected; (2) the attainable current in the voltage-limited region above base speed as a function of terminal voltage, speed, and current-phase angle; (3) the attainable current in the voltage-limited region above base speed as a function of terminal voltage, speed, and voltage-phase angle; (4) the maximum-power output in the voltage-limited region above base speed as a function of speed; (5) the optimal voltage-phase angle in the voltage-limited region above base speed required to obtain maximum-power output; (6) the maximum-power speed curve which was linear from rest to base speed in the current limited region below base speed; (7) the current angle as a function of saliency ratio in the current-limited region below base speed; and (8) the torque as a function of saliency ratio which is almost linear in the current-limited region below base speed. The equations were applied to model Motor X using numerically-oriented methods with the computer tool LabVIEW. The equations were solved iteratively to find optimal current and voltage angles that yield maximum power and maximum efficiency from rest through the current-limited region to base speed and then through the voltage-limited region to high-rotational speeds. Currents, voltages, and reluctance factors were all calculated and external loops were employed to perform additional optimization with respect to PM pitch angle (magnet fraction) and with respect to magnet strength. The conclusion was that the optimal-magnet fraction for Motor X is 0.72 which corresponds to a PM pitch angle of 130{sup o}, a value close to the maximum-saliency ratio in a plot of saliency ratio versus PM pitch angle. Further, the strength of Motor X magnets may be lowered to 80% of full strength without significantly impacting motor performance for PM pitch angles between the peak saliency (130{sup o}) and peak-characteristic current (160{sup o}). It is recommended that future research involve maximizing a driving-cycle-weighted efficiency based on the Federal Urban Driving Cycle and the Federal Highway Driving Cycle as criteria for selecting the final optimal-PM fraction and magnet strength for this inset PM motor. Results of this study indicate that the reduction in PM torque due to reduced-magnet fraction will be more than compensated by the reluctance torque resulting from the higher saliency ratio. It seems likely that the best overall performance will require saliency; consequently, we think the best motor will be a reluctance-assisted PM motor. This should be explored for use with other types of PM motors, such as fractional-slot motors with concentrated windings.

Otaduy, P.J.

2006-01-13T23:59:59.000Z

486

Modeling and characterization of a voice coil motor  

E-Print Network [OSTI]

This thesis describes the development of a voice-coil motor that will allow viscous fluids to be delivered via a portable needle-free injection device. The chosen motor design features opposing magnets whose flux is channeled ...

Brown, Ashley (Ashley A.)

2012-01-01T23:59:59.000Z

487

9.373 Somatosensory and Motor Systems, Spring 2002  

E-Print Network [OSTI]

General principles of motor control in biological systems. Structure and function of sensory receptors. Muscle structure and reflex arcs. Spinal cord. Locomotion. Oculomotor control. Cerebellar structure and function. Motor ...

Bizzi, Emilio

488

The Binding of Learning to Action in Motor Adaptation  

E-Print Network [OSTI]

In motor tasks, errors between planned and actual movements generally result in adaptive changes which reduce the occurrence of similar errors in the future. It has commonly been assumed that the motor adaptation arising ...

Gonzalez Castro, Luis Nicolas

489

Secrets of the Motor That Drives Archaea Revealed  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Secrets of the Motor That Drives Archaea Revealed Secrets of the Motor That Drives Archaea Revealed Print Thursday, 14 February 2013 00:00 An international team led by John Tainer...

490

An Examination of Motor Skills in Children who Stutter  

E-Print Network [OSTI]

Recently, research has postulated that stuttering is a motor disorder that results from brain abnormalities within the central nervous system. Based on evidence of numerous irregularities within various motor systems, it has been suggested...

2012-10-19T23:59:59.000Z

491

Transient Peak Currents in Permanent Magnet Synchronous Motors  

E-Print Network [OSTI]

synchronous motors (PMSM) became more and more popular for these applications. The performance of PMSM drives not be triggered at motor operating points, for which the SSC current behavior will damage the PMSM drive. An analysis of PMSM behavior with

Paderborn, Universität

492

Electrical Equipment Inspection Program Electrical Safety  

E-Print Network [OSTI]

Electrical Equipment Inspection Program Electrical Safety SLAC-I-730-0A11A-001-R003 23 March 2005 Document Title: Electrical Equipment Inspection Program Original Publication Date: 19 January 2005 Revised Publication Date: 23 March 2005 (updated 29 November 2010) Department: Electrical Safety Document Number: SLAC

Wechsler, Risa H.

493

Fuzzy logic electric vehicle regenerative antiskid braking and traction control system  

DOE Patents [OSTI]

An regenerative antiskid braking and traction control system using fuzzy logic for an electric or hybrid vehicle having a regenerative braking system operatively connected to an electric traction motor, and a separate hydraulic braking system includes sensors for monitoring present vehicle parameters and a processor, responsive to the sensors, for calculating vehicle parameters defining the vehicle behavior not directly measurable by the sensor and determining if regenerative antiskid braking control, requiring hydraulic braking control, and requiring traction control are required. The processor then employs fuzzy logic based on the determined vehicle state and provides command signals to a motor controller to control operation of the electric traction motor and to the brake controller to control fluid pressure applied at each vehicle wheel to provide the appropriate regenerative braking control, hydraulic braking control, and traction control. 123 figs.

Cikanek, S.R.

1994-10-25T23:59:59.000Z

494

Evaluation of 2004 Toyota Prius Hybrid Electric Drive System Interim Report  

SciTech Connect (OSTI)

Laboratory tests were conducted to evaluate the electrical and mechanical performance of the 2004 Toyota Prius and its hybrid electric drive system. As a hybrid vehicle, the 2004 Prius uses both a gasoline-powered internal combustion engine and a battery-powered electric motor as motive power sources. Innovative algorithms for combining these two power sources results in improved fuel efficiency and reduced emissions compared to traditional automobiles. Initial objectives of the laboratory tests were to measure motor and generator back-electromotive force (emf) voltages and determine gearbox-related power losses over a specified range of shaft speeds and lubricating oil temperatures. Follow-on work will involve additional performance testing of the motor, generator, and inverter. Information contained in this interim report summarizes the test results obtained to date, describes preliminary conclusions and findings, and identifies additional areas for further study.

Ayers, C.W.

2004-11-23T23:59:59.000Z

495

Fuzzy logic electric vehicle regenerative antiskid braking and traction control system  

DOE Patents [OSTI]

An regenerative antiskid braking and traction control system using fuzzy logic for an electric or hybrid vehicle having a regenerative braking system operatively connected to an electric traction motor, and a separate hydraulic braking system includes sensors for monitoring present vehicle parameters and a processor, responsive to the sensors, for calculating vehicle parameters defining the vehicle behavior not directly measurable by the sensor and determining if regenerative antiskid braking control, requiring hydraulic braking control, and requiring traction control are required. The processor then employs fuzzy logic based on the determined vehicle state and provides command signals to a motor controller to control operation of the electric traction motor and to the brake controller to control fluid pressure applied at each vehicle wheel to provide the appropriate regenerative braking control, hydraulic braking control, and traction control.

Cikanek, Susan R. (Wixom, MI)

1994-01-01T23:59:59.000Z

496

Extending the Constant Power Speed Range of the Brushless DC Motor through Dual Mode Inverter Control -- Part I: Theory and Simulation  

SciTech Connect (OSTI)

An inverter topology and control scheme has been developed that can drive low-inductance, surface-mounted permanent magnet motors over the wide constant power speed range required in electric vehicle applications. This new controller is called the dual-mode inverter control (DMIC) [1]. The DMIC can drive either the Permanent Magnet Synchronous Machine (PMSM) with sinusoidal back emf, or the brushless dc machine (BDCM) with trapezoidal emf in the motoring and regenerative braking modes. In this paper we concentrate on the BDCM under high-speed motoring conditions. Simulation results show that if all motor and inverter loss mechanisms are neglected, the constant power speed range of the DMIC is infinite. The simulation results are supported by closed form expressions for peak and rms motor current and average power derived from analytical solution to the differential equations governing the DMIC/BDCM drive for the lossless case. The analytical solution shows that the range of motor inductance that can be accommodated by the DMIC is more than an order of magnitude such that the DMIC is compatible with both low- and high-inductance BDCMs. Finally, method is given for integrating the classical hysteresis band current control, used for motor control below base speed, with the phase advance of DMIC that is applied above base speed. The power versus speed performance of the DMIC is then simulated across the entire speed range.

Lawler, J.S.

2001-10-29T23:59:59.000Z

497

VIRTUAL E-MOTOR AS A TOOL FOR THE DEVELOPMENT  

E-Print Network [OSTI]

is the motor model employed by the emulator. Standard models have limited performance, such as the linear PMSM

Paderborn, Universität

498

Optimal Current Waveforms for Brushless Permanent Magnet Motors  

E-Print Network [OSTI]

;1 Introduction We consider the problem of controlling an AC permanent magnet synchronous motor (PMSM) by choosing

499

Theories of rotary motors Richard M. Berry  

E-Print Network [OSTI]

and the `proton turbine' model of La« uger or Berry. Models such as these are typically represented by a small connected to an extracellular helical propeller. The motor is powered by the £ow of ions down to the helical propeller, or `¢lament'. The stator is a ring of particles in the cytoplasmic membrane, containing

Berry, Richard

500

January 08 1 Ford -Chrysler -General Motors  

E-Print Network [OSTI]

January 08 1 Ford - Chrysler - General Motors DOE Fuel Cell Pre-Solicitation Workshop worthy - and not worthy - of study in the DOE Fuel Cell Subprogram · Categories described within DOE Fuel for Study · PGM cathode catalysts, mass activity > 0.44 A/mgPGM ­ Core/shell ­ Structure-controlled PGM