Sample records for 26-watt compact fluorescent

  1. Covered Product Category: Compact Fluorescent Lamps

    Broader source: Energy.gov [DOE]

    FEMP provides acquisition guidance across a variety of product categories, including compact fluorescent lamps (CFLs), which are an ENERGY STAR-qualified product category.

  2. The Hazards of Use and Disposal of Compact Fluorescent Bulbs Compact fluorescent lights (aka. CFLs) work by exciting a phosphorous coating within the tube to emit

    E-Print Network [OSTI]

    Maroncelli, Mark

    The Hazards of Use and Disposal of Compact Fluorescent Bulbs Compact fluorescent lights (aka. CFLs the bulb to be an efficient light source. By comparison, older home thermometers contain 500 milligrams decade. HOW SHOULD I DISPOSE OF CFL'S? The presence of mercury requires that all CFL bulbs are properly

  3. Mercury Lamps Recycling Fluorescent light-tubes, compact fluorescent bulbs, mercury and sodium vapor lamps, ultraviolet and

    E-Print Network [OSTI]

    Baker, Chris I.

    Mercury Lamps Recycling Fluorescent light-tubes, compact fluorescent bulbs, mercury and sodium labeled for shipment to a recycling plant for mercury, glass and aluminum recovery. The beneficial re can be recycled infinitely without losing its purity or strength. While the primary end product

  4. Conservation potential of compact fluorescent lamps in India and Brazil

    SciTech Connect (OSTI)

    Gadgil, A.; Martino Jannuzzi, G. de (Lawrence Berkeley Lab., CA (USA); Universidade Estadual de Campinas, SP (Brazil). Faculdade de Engenharia)

    1989-07-01T23:59:59.000Z

    We evaluate the conservation potential of compact fluorescent lamps (CFLs) for managing the rapidly increasing electrical energy and peak demand in India and Brazil. Using very conservative assumptions, we find that the cost of conserved energy using 16 W CFLs is 4 and 6 times less than the long range marginal cost of electricity for the two countries. The cost of avoided peak installed capacity is 6 and 9.5 times less than the cost of new installed capacity for India and Brazil. The analysis is undertaken from the three separate perspectives of the national economies, the consumers, and the utilities. We find that because residential electricity is subsidized, the consumers have little or no incentive to purchase and install the CFLs, unless they too are subsidized. However, the benefits of CFL installation to the utility are so large that subsidizing them is a paying proposition for the utility are so large that subsidizing them is a paying proposition for the utility in almost all cases. As an illustration of a gradual introduction strategy for CFLs, we calculate a scenario where national savings of the order of US $1.2 million per day for India and US $2.5 million per day for Brazil are reached in 10 years by a small and gradual transfer of subsidy from residential electricity to CFLs. We then explore the barriers to immediate large scale introduction of these lamps in the two countries. Specific technical and marketing problems are identified and discussed, which would require solution before such an introduction can be attempted. Lastly, we discuss the range of policy instruments, in addition to a subsidy scheme, that can be used for promoting the diffusion of these lamps in the domestic and commercial sector. 47 refs., 15 figs., 2 tabs.

  5. Compact Fluorescent Plug-In Ballast-in-a-Socket

    SciTech Connect (OSTI)

    Rebecca Voelker

    2001-12-21T23:59:59.000Z

    The primary goal of this program was to develop a ballast system for plug-in CFLs (compact fluorescent lamps) that will directly replace standard metal shell, medium base incandescent lampholders (such as Levition No. 6098) for use with portable lamp fixtures, such as floor, table and desk lamps. A secondary goal was to identify a plug-in CFL that is optimized for use with this ballast. This Plug-in CFL Ballastin-a-Socket system will allow fixture manufacturers to easily manufacture CFL-based high-efficacy portable fixtures that provide residential and commercial consumers with attractive, cost-effective, and energy-efficient fixtures for use wherever portable incandescent fixtures are used today. The advantages of this proposed system over existing CFL solutions are that the fixtures can only be used with high-efficacy CFLs, and they will be more attractive and will have lower life-cycle costs than screw-in or adapter-based CFL retrofit solutions. These features should greatly increase the penetration of CFL's into the North American market. Our work has shown that using integrated circuits it is quite feasible to produce a lamp-fixture ballast of a size comparable to the current Edison-screw 3-way incandescent fixtures. As for price points for BIAS-based fixtures, end-users polled by the Lighting Research Institute at RPI indicated that they would pay as much as an additional $10 for a lamp containing such a ballast. The ballast has been optimized to run with a 26 W amalgam triple biax lamp in the base-down position, yet can accept non-amalgam versions of the lamp. With a few part alterations, the ballast can be produced to support 32 W lamps as well. The ballast uses GE's existing L-Comp[1] power topology in the circuit so that the integrated circuit design would be a design that could possibly be used by other CFL and EFL products with minor modifications. This gives added value by reducing cost and size of not only the BIAS, but also possibly other integral CFL and future dimmable integral and plug-in versions of the EFL products.

  6. Convection venting lensed reflector-type compact fluorescent lamp system

    DOE Patents [OSTI]

    Pelton, B.A.; Siminovitch, M.

    1997-07-29T23:59:59.000Z

    Disclosed herein is a fluorescent lamp housing assembly capable of providing convection cooling to the lamp and the ballast. The lens of the present invention includes two distinct portions, a central portion and an apertured portion. The housing assembly further includes apertures so that air mass is able to freely move up through the assembly and out ventilation apertures. 12 figs.

  7. Convection venting lensed reflector-type compact fluorescent lamp system

    DOE Patents [OSTI]

    Pelton, Bruce A. (825 Manor Rd., El Sobrante, CA 94803); Siminovitch, Michael (829 Manor Rd., El Sobrante, CA 94803)

    1997-01-01T23:59:59.000Z

    Disclosed herein is a fluorescent lamp housing assembly capable of providing convection cooling to the lamp and the ballast. The lens of the present invention includes two distinct portions, a central portion and an apertured portion. The housing assembly further includes apertures so that air mass is able to freely move up through the assembly and out ventilation apertures.

  8. Compact fluorescent lamp using horizontal and vertical insulating septums and convective venting geometry

    DOE Patents [OSTI]

    Siminovitch, M.

    1998-02-10T23:59:59.000Z

    A novel design is described for a compact fluorescent lamp, including a lamp geometry which will increase light output and efficacy of the lamp in a base down operating position by providing horizontal and vertical insulating septums positioned in the ballast compartment of the lamp to provide a cooler coldspot. Selective convective venting provides additional cooling of the ballast compartment. 9 figs.

  9. Frequently Asked Questions Information on Compact Fluorescent Light Bulbs (CFLs) and Mercury

    E-Print Network [OSTI]

    Jia, Songtao

    Frequently Asked Questions Information on Compact Fluorescent Light Bulbs (CFLs) and Mercury February 2008 Why should people use CFLs? Switching from traditional light bulbs to CFLs is an effective light bulbs, last up to 10 times longer, cost little up front, and provide a quick return on investment

  10. Compact Fluorescent Lighting in America: Lessons Learned on the Way to Market

    SciTech Connect (OSTI)

    Sandahl, Linda J.; Gilbride, Theresa L.; Ledbetter, Marc R.; Steward, Heidi E.; Calwell, Chris

    2006-05-22T23:59:59.000Z

    This report describes the history of compact fluorescent lamps (CFLs) in America. CFLs were introduced in the 1970s; however, it has taken more than 20 years for them to gain widespread recognition in the U.S. residential lighting market. This report reviews the development of CFLs, efforts to increase market acceptance of them, and barriers to that acceptance. Lessons to be learned from this study of CFLs are identified in hopes of assisting future market introduction efforts for other promising energy-efficient technologies. This report was prepared by the Pacific Northwest National Laboratory for the U.S. Department of Energy’s Office of Building Technologies, Emerging Technologies Program.

  11. A Review of the Reflector Compact Fluorescent Lights Technology Procurement Program: Conclusions and Results

    SciTech Connect (OSTI)

    Sandahl, Linda J.; Gilbride, Theresa L.; Ledbetter, Marc R.; McCullough, Jeffrey J.

    2008-05-19T23:59:59.000Z

    This report describes a project sponsored by the U.S. Department of Energy (DOE) and implemented by the Pacific Northwest National Laboratory (PNNL), from 2000 to 2007 to improve the performance of reflector type (R-lamp) compact fluorescent lamps (CFLs) and increase their availability throughout the United States by means of a technology development and procurement strategy. In 2000, at the request of the U.S. Department of Energy’s Emerging Technologies Program and its predecessors, the Pacific Northwest National Laboratory undertook a technology procurement seeking R-CFLs that were specifically designed for use in ICAT recessed can fixtures and that met other minimum performance criteria including minimum light output and size restrictions (to ensure they fit in standard residential recessed cans). The technology procurement included two phases. In Phase I, requests for proposals (RFPs) were issued in October 2002 and five manufacturers responded with 12 lamp models. Eight of these models met the minimum requirements and passed the 6-hour short-term test in a simulated ICAT environment. These eight models were subjected to long-term tests of 6,000 or more hours in a simulated ICAT environment. Three of these models passed the short- and long-term tests and were promoted through the program website (www.pnl.gov/rlamps), press releases, and fliers. To increase the number of qualifying models, a second RFP was issued in June 2005. In April 2007, DOE announced that 16 reflector CFL (R-CFL) models by four manufacturers had met all the minimum requirements of Phase 2 of the R-CFL Technology Innovation Competition. PNNL developed both the criteria and the test apparatus design for Elevated Temperature Life Testing (ETLT), which has been included by DOE in its draft ENERGY STAR specifications for the reflector category of CFLs. PNNL promoted the winning lamps through a program website, press releases, and fliers as well as through program partners. PNNL also helped engage distributors including Costco, the Home Depot, Bonneville Power Administration, and utility organizations.

  12. Max Tech and Beyond: Fluorescent Lamps

    E-Print Network [OSTI]

    Scholand, Michael

    2012-01-01T23:59:59.000Z

    Laboratory, LBNL-4998E. General Electric Lamp and BallastEuropean Union General Electric High Intensity DischargeEnergy Saver”; and General Electric has a 26 watt T5 lamp (

  13. Energy Savings and Green Initiatives Project Grant

    SciTech Connect (OSTI)

    Kathy MacLennan

    2011-11-21T23:59:59.000Z

    This project entails retrofitting all four foot, 2, 3 and 4 bulb 40 watt T12 fixtures to T8 28 watt and 150 watt incandescent to 26 watt compact fluorescent bulbs. In total, 2,086 fixtures will be retrofitted

  14. Doppler-free intermodulated fluorescence spectroscopy of $^4He$ $2^3P-3^{1,3}D$ transitions at 588 nm with a one-watt compact laser system

    E-Print Network [OSTI]

    Luo, Pei-Ling; Feng, Yan; Wang, Li-Bang; Shy, Jow-Tsong

    2015-01-01T23:59:59.000Z

    We have demonstrated Doppler-free intermodulated fluorescence spectroscopy of helium $2^3P-3^{1,3}D$ transitions in an rf discharged sealed-off cell using a compact laser system at 588 nm. An external cavity diode laser at 1176 nm was constructed to seed a Raman fiber amplifier. Laser power of more than one watt at 588 nm was produced by frequency doubling of the fiber amplifier output using a MgO:PPLN crystal. A doubling efficiency of 23 % was achieved. The power-dependent spectra of the $2^3P-3^3D$ transitions were investigated. Furthermore, the Doppler-free spectrum of the spin-forbidden $2^3P-3^1D$ transitions was observed for the first time. Our results are crucial towards precision test of QED atomic calculations, especially for improving the determination of the helium $3^1D-3^3D$ separation.

  15. Fluorescent refrigeration

    DOE Patents [OSTI]

    Epstein, Richard I. (Santa Fe, NM); Edwards, Bradley C. (Los Alamos, NM); Buchwald, Melvin I. (Santa Fe, NM); Gosnell, Timothy R. (Santa Fe, NM)

    1995-01-01T23:59:59.000Z

    Fluorescent refrigeration is based on selective radiative pumping, using substantially monochromatic radiation, of quantum excitations which are then endothermically redistributed to higher energies. Ultimately, the populated energy levels radiatively deexcite emitting, on the average, more radiant energy than was initially absorbed. The material utilized to accomplish the cooling must have dimensions such that the exciting radiation is strongly absorbed, but the fluorescence may exit the material through a significantly smaller optical pathlength. Optical fibers and mirrored glasses and crystals provide this requirement.

  16. Pecos River Compact (Texas)

    Broader source: Energy.gov [DOE]

    This legislation authorizes the state's entrance into the Pecos River Compact, a joint agreement between the states of New Mexico and Texas. The compact is administered by the Pecos River Compact...

  17. Fluorescent refrigeration

    DOE Patents [OSTI]

    Epstein, R.I.; Edwards, B.C.; Buchwald, M.I.; Gosnell, T.R.

    1995-09-05T23:59:59.000Z

    Fluorescent refrigeration is based on selective radiative pumping, using substantially monochromatic radiation, of quantum excitations which are then endothermically redistributed to higher energies. Ultimately, the populated energy levels radiatively deexcite emitting, on the average, more radiant energy than was initially absorbed. The material utilized to accomplish the cooling must have dimensions such that the exciting radiation is strongly absorbed, but the fluorescence may exit the material through a significantly smaller optical pathlength. Optical fibers and mirrored glasses and crystals provide this requirement. 6 figs.

  18. Integrated ultrasonic particle positioning and low excitation light fluorescence imaging

    SciTech Connect (OSTI)

    Bernassau, A. L.; Al-Rawhani, M.; Beeley, J.; Cumming, D. R. S. [School of Engineering, University of Glasgow, Glasgow, G12 8LT (United Kingdom)] [School of Engineering, University of Glasgow, Glasgow, G12 8LT (United Kingdom)

    2013-12-09T23:59:59.000Z

    A compact hybrid system has been developed to position and detect fluorescent micro-particles by combining a Single Photon Avalanche Diode (SPAD) imager with an acoustic manipulator. The detector comprises a SPAD array, light-emitting diode (LED), lenses, and optical filters. The acoustic device is formed of multiple transducers surrounding an octagonal cavity. By stimulating pairs of transducers simultaneously, an acoustic landscape is created causing fluorescent micro-particles to agglomerate into lines. The fluorescent pattern is excited by a low power LED and detected by the SPAD imager. Our technique combines particle manipulation and visualization in a compact, low power, portable setup.

  19. NSTX LTXPEGASUS Compact CTF

    E-Print Network [OSTI]

    Princeton Plasma Physics Laboratory

    isotope retention. ST-CTF Compact ST-CTF at ~ 10 MA range provide a compact nuclear component test to NSTX. Large vacuum vessel, no stabilizing plates, excellent set of profile and boundary diagnostics

  20. Red River Compact (Texas)

    Broader source: Energy.gov [DOE]

    The Red River Compact Commission administers the Red River Compact to ensure that Texas receives its equitable share of quality water from the Red River and its tributaries as apportioned by the...

  1. Rio Grande Compact (Texas)

    Broader source: Energy.gov [DOE]

    This legislation authorizes the state's entrance into the Rio Grande Compact, a joint agreement between the states of Colorado, New Mexico, and Texas. The compact is administered by the Rio Grande...

  2. Canadian River Compact (Texas)

    Broader source: Energy.gov [DOE]

    The Canadian River Commission administers the Canadian River Compact which includes the states of New Mexico, Oklahoma, and Texas. Signed in 1950 by the member states, the Compact was subsequently...

  3. Interstate Mining Compact (Maryland)

    Broader source: Energy.gov [DOE]

    This legislation authorizes the state's entrance into the Interstate Mining Compact, a multi-state governmental agency / organization that represents the natural resource and related environmental...

  4. Laboratory compaction of cohesionless sands

    E-Print Network [OSTI]

    Delphia, John Girard

    1998-01-01T23:59:59.000Z

    on the maximum dry unit weight during compaction. Three different laboratory compaction methods were used: 1) Standard Proctor', 2) Modified Proctor; and 3) Vibrating hammer. The effects of the grain size distribution, particle shape and laboratory compaction...

  5. Conservation Potential of Compact Fluorescent Lamps in India and Brazil

    E-Print Network [OSTI]

    Gadgil, A.J.

    2008-01-01T23:59:59.000Z

    cost of avoided peak installed capacity is 6 and 9.5 timesthe cost of new installed capacity for India and Brazil. Theappear to require an installed capacity of more than 100 GW

  6. Zero energy-storage ballast for compact fluorescent lamps

    DOE Patents [OSTI]

    Schultz, W.N.; Thomas, R.J.

    1999-08-31T23:59:59.000Z

    A CFL ballast includes complementary-type switching devices connected in series with their gates connected together at a control node. The switching devices supply a resonant tank circuit which is tuned to a frequency near, but slightly lower than, the resonant frequency of a resonant control circuit. As a result, the tank circuit restarts oscillations immediately following each zero crossing of the bus voltage. Such rapid restarts avoid undesirable flickering while maintaining the operational advantages and high efficacy of the CFL ballast. 4 figs.

  7. Conservation Potential of Compact Fluorescent Lamps in India and Brazil

    E-Print Network [OSTI]

    Gadgil, A.J.

    2008-01-01T23:59:59.000Z

    utility managed program in an LDC).3r'e split the additionalseems obvious that almost no LDC domestic consumers will buy

  8. Zero energy-storage ballast for compact fluorescent lamps

    DOE Patents [OSTI]

    Schultz, William Newell (Niskayuna, NY); Thomas, Robert James (Rexford, NY)

    1999-01-01T23:59:59.000Z

    A CFL ballast includes complementary-type switching devices connected in series with their gates connected together at a control node. The switching devices supply a resonant tank circuit which is tuned to a frequency near, but slightly lower than, the resonant frequency of a resonant control circuit. As a result, the tank circuit restarts oscillations immediately following each zero crossing of the bus voltage. Such rapid restarts avoid undesirable flickering while maintaining the operational advantages and high efficacy of the CFL ballast.

  9. Conservation Potential of Compact Fluorescent Lamps in India and Brazil

    E-Print Network [OSTI]

    Gadgil, A.J.

    2008-01-01T23:59:59.000Z

    1988. The private sector in Brazil owned (in 1986) 40% ofElectricity Conservation in Brazil: Potential and Pro-electricity consumption in Brazil's residential sector was

  10. Conservation Potential of Compact Fluorescent Lamps in India and Brazil

    E-Print Network [OSTI]

    Gadgil, A.J.

    2008-01-01T23:59:59.000Z

    energia: 0 Horario de Verao) Proceedings, I Congres- so Brasileiro de Planejamento Energetico (forthcoming), Universidade Es- tadual de Campinas, Sao Paulo, Brasil,

  11. Conservation Potential of Compact Fluorescent Lamps in India and Brazil

    E-Print Network [OSTI]

    Gadgil, A.J.

    2008-01-01T23:59:59.000Z

    Residential Energy Demand in Brazil and Income Classes:in Brazil: Potential and Pro- gress", ENERGY, vol. 13, no.decreasing energy services in India and Brazil. The initial

  12. Energy Cost Calculator for Compact Fluorescent Lamps | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page onYouTube YouTube Note: Since the YouTube|6721 Federal Register /of Energy 3 BTOWebinarSupplies;Ice Machines

  13. Conservation Potential of Compact Fluorescent Lamps in India and Brazil

    E-Print Network [OSTI]

    Gadgil, A.J.

    2008-01-01T23:59:59.000Z

    household income is a strong determinant of household electricity use, analysis for different prices

  14. Lighting the Way with Compact Fluorescent Lighting | Department of Energy

    Energy Savers [EERE]

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page onYou are now leaving Energy.gov You are now leaving Energy.gov You are being directed off Energy.gov. Are you sure you wantJoin us for #SpaceWeek Join us for #SpaceWeekDepartmentLight

  15. Covered Product Category: Compact Fluorescent Lamps | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page onYouTube YouTube Note: Since the YouTube platformBuildingCoalComplex(GC-72)Columbia Government | Department ofProducts

  16. Medium Base Compact Fluorescent Lamps | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels DataDepartment of Energy Your Density Isn't YourTransport(FactDepartment3311, 3312), October 20122Technologies61-2008 JuneMedication List

  17. Fluorescent optical position sensor

    DOE Patents [OSTI]

    Weiss, Jonathan D.

    2005-11-15T23:59:59.000Z

    A fluorescent optical position sensor and method of operation. A small excitation source side-pumps a localized region of fluorescence at an unknown position along a fluorescent waveguide. As the fluorescent light travels down the waveguide, the intensity of fluorescent light decreases due to absorption. By measuring with one (or two) photodetectors the attenuated intensity of fluorescent light emitted from one (or both) ends of the waveguide, the position of the excitation source relative to the waveguide can be determined by comparing the measured light intensity to a calibrated response curve or mathematical model. Alternatively, excitation light can be pumped into an end of the waveguide, which generates an exponentially-decaying continuous source of fluorescent light along the length of the waveguide. The position of a photodetector oriented to view the side of the waveguide can be uniquely determined by measuring the intensity of the fluorescent light emitted radially at that location.

  18. Safe biodegradable fluorescent particles

    DOE Patents [OSTI]

    Martin, Sue I. (Berkeley, CA); Fergenson, David P. (Alamo, CA); Srivastava, Abneesh (Santa Clara, CA); Bogan, Michael J. (Dublin, CA); Riot, Vincent J. (Oakland, CA); Frank, Matthias (Oakland, CA)

    2010-08-24T23:59:59.000Z

    A human-safe fluorescence particle that can be used for fluorescence detection instruments or act as a safe simulant for mimicking the fluorescence properties of microorganisms. The particle comprises a non-biological carrier and natural fluorophores encapsulated in the non-biological carrier. By doping biodegradable-polymer drug delivery microspheres with natural or synthetic fluorophores, the desired fluorescence can be attained or biological organisms can be simulated without the associated risks and logistical difficulties of live microorganisms.

  19. Compact microchannel system

    DOE Patents [OSTI]

    Griffiths, Stewart

    2003-09-30T23:59:59.000Z

    The present invention provides compact geometries for the layout of microchannel columns through the use of turns and straight channel segments. These compact geometries permit the use of long separation or reaction columns on a small microchannel substrate or, equivalently, permit columns of a fixed length to occupy a smaller substrate area. The new geometries are based in part on mathematical analyses that provide the minimum turn radius for which column performance in not degraded. In particular, we find that straight channel segments of sufficient length reduce the required minimum turn radius, enabling compact channel layout when turns and straight segments are combined. The compact geometries are obtained by using turns and straight segments in overlapped or nested arrangements to form pleated or coiled columns.

  20. Industrial Optimization Compact Course

    E-Print Network [OSTI]

    Kirches, Christian

    Industrial Optimization Compact Course and Challenge Workshop Optimization plays a crucial role of the processes are typically nonlinear and dyna- mic. Thus, complex dynamic optimization or optimal control in industrial optimization. February 17­20, 2014 ·9.00­17.00 IWR ·Im Neuenheimer Feld 368 ·69120 Heidelberg www

  1. Progress in Compact Toroid Experiments

    SciTech Connect (OSTI)

    Dolan, Thomas James

    2002-09-01T23:59:59.000Z

    The term "compact toroids" as used here means spherical tokamaks, spheromaks, and field reversed configurations, but not reversed field pinches. There are about 17 compact toroid experiments under construction or operating, with approximate parameters listed in Table 1.

  2. Sabine River Compact (Multiple States)

    Broader source: Energy.gov [DOE]

    The Sabine River Compact Commission administers the Sabine River Compact to ensure that Texas receives its equitable share of quality water from the Sabine River and its tributaries as apportioned...

  3. Fluorescent Tube Lamps

    Broader source: Energy.gov [DOE]

    FEMP temporarily suspended its energy efficiency requirements for fluorescent tube lamps as it evaluates the market impact of the pending 2012 minimum efficiency standards for fluorescent lamps. The program will issue updated energy efficiency requirements when the market distribution of this product category stabilizes and when doing so has the potential to result in significant Federal energy savings.

  4. Compact Spreader Schemes

    SciTech Connect (OSTI)

    Placidi, M.; Jung, J. -Y.; Ratti, A.; Sun, C.

    2014-07-25T23:59:59.000Z

    This paper describes beam distribution schemes adopting a novel implementation based on low amplitude vertical deflections combined with horizontal ones generated by Lambertson-type septum magnets. This scheme offers substantial compactness in the longitudinal layouts of the beam lines and increased flexibility for beam delivery of multiple beam lines on a shot-to-shot basis. Fast kickers (FK) or transverse electric field RF Deflectors (RFD) provide the low amplitude deflections. Initially proposed at the Stanford Linear Accelerator Center (SLAC) as tools for beam diagnostics and more recently adopted for multiline beam pattern schemes, RFDs offer repetition capabilities and a likely better amplitude reproducibility when compared to FKs, which, in turn, offer more modest financial involvements both in construction and operation. Both solutions represent an ideal approach for the design of compact beam distribution systems resulting in space and cost savings while preserving flexibility and beam quality.

  5. Global Compact for Higher Education Institutions

    E-Print Network [OSTI]

    Global Compact for Higher Education Institutions Communicating on Progress for Université Laval Guide to the United Nations Global Compact for Higher Education Institutions: Implementing the Global to the United Nations Global Compact for Higher Education Institutions: Implementing the Global Compact

  6. Recombinant fluorescent protein microsphere calibration standard

    DOE Patents [OSTI]

    Nolan, John P. (Santa Fe, NM); Nolan, Rhiannon L. (Santa Fe, NM); Ruscetti, Teresa (Los Alamos, NM); Lehnert, Bruce E. (Los Alamos, NM)

    2001-01-01T23:59:59.000Z

    A method for making recombinant fluorescent protein standard particles for calibration of fluorescence instruments.

  7. Fluorescent filtered electrophosphorescence

    DOE Patents [OSTI]

    Forrest, Stephen (Ann Arbor, MI); Sun, Yiru (Princeton, NJ); Giebink, Noel (Ann Arbor, MI); Thompson, Mark E. (Anaheim Hills, CA)

    2010-08-03T23:59:59.000Z

    The present invention relates to organic light emitting devices (OLEDs), and more specifically to OLEDS that emit light using a combination of fluorescent emitters and phosphorescent emitters for the efficient utilization of all of the electrically generated excitons.

  8. Fluorescent filtered electrophosphorescence

    DOE Patents [OSTI]

    Forrest, Stephen R. (Princeton, NJ); Sun, Yiru (Princeton, NJ); Giebink, Noel (Princeton, NJ); Thompson, Mark E. (Anaheim Hills, CA)

    2009-01-06T23:59:59.000Z

    The present invention relates to organic light emitting devices (OLEDs), and more specifically to OLEDS that emit light using a combination of fluorescent emitters and phosphorescent emitters for the efficient utilization of all of the electrically generated excitons.

  9. Accretion in Compact Binaries

    E-Print Network [OSTI]

    Andrew R. King

    2003-03-26T23:59:59.000Z

    Compact binaries have long been a paradigm for accretion theory. Much of our present view of how accretion occurs comes directly from the comparison of theory with observations of these sources. Since theory differs little for other objects such as active galaxies, increasing efforts have recently gone into searching for correspondences in observed behaviour. This chapter aims at giving a concise summary of the field, with particular emphasis on new developments since the previous edition of this book. These developments have been significant. Much of the earlier literature implicitly assumed that accreting binaries were fairly steady sources accreting most of the mass entering their vicinity, often with main-sequence companions, and radiating the resulting accretion luminosity in rough isotropy. We shall see that in reality these assumptions fail for the majority of systems. Most are transient; mass ejection in winds and jets is extremely common; a large (sometimes dominant) fraction of even short-period systems have evolved companions whose structure deviates significantly from the zero-age main sequence; and the radiation pattern of many objects is significantly anisotropic. It is now possible to give a complete characterization of the observed incidence of transient and persistent sources in terms of the disc instability model and formation constraints. X-ray populations in external galaxies, particularly the ultraluminous sources, are revealing important new insights into accretion processes and compact binary evolution.

  10. Susquehanna River Basin Compact (Maryland)

    Broader source: Energy.gov [DOE]

    This legislation enables the state's entrance into the Susquehanna River Basin Compact, which provides for the conservation, development, and administration of the water resources of the...

  11. Fluorescent image tracking velocimeter

    DOE Patents [OSTI]

    Shaffer, Franklin D. (Library, PA)

    1994-01-01T23:59:59.000Z

    A multiple-exposure fluorescent image tracking velocimeter (FITV) detects and measures the motion (trajectory, direction and velocity) of small particles close to light scattering surfaces. The small particles may follow the motion of a carrier medium such as a liquid, gas or multi-phase mixture, allowing the motion of the carrier medium to be observed, measured and recorded. The main components of the FITV include: (1) fluorescent particles; (2) a pulsed fluorescent excitation laser source; (3) an imaging camera; and (4) an image analyzer. FITV uses fluorescing particles excited by visible laser light to enhance particle image detectability near light scattering surfaces. The excitation laser light is filtered out before reaching the imaging camera allowing the fluoresced wavelengths emitted by the particles to be detected and recorded by the camera. FITV employs multiple exposures of a single camera image by pulsing the excitation laser light for producing a series of images of each particle along its trajectory. The time-lapsed image may be used to determine trajectory and velocity and the exposures may be coded to derive directional information.

  12. Fluorescence analyzer for lignin

    SciTech Connect (OSTI)

    Berthold, J.W.; Malito, M.L.; Jeffers, L.

    1993-06-01T23:59:59.000Z

    An apparatus for measuring lignin concentration with time resolved fluorescence in an undiluted wood pulp or black liquor sample, on a real-time, in situ basis is described, comprising: light source means for applying excitation light pulses at a selected wavelength and at known time intervals to the undiluted sample for causing the lignin concentration to produce fluorescent emission light with a fluorescence intensity that monotonically decreases in a quenched fluorescence regime; light detector means for measuring the emission light at the known time intervals and establishing signals indicative thereof; switching means for turning said light detector means on at precise specified time intervals after each excitation light pulse; and signal processing means connected to the light source means and the light detector means for comparing intensities of the emission light from the lignin in the quenched fluorescence regime to the intensities of the excitation light pulses on a time resolved basis for providing a measurement of the lignin concentration in the undiluted sample as a function of the time resolved emission light intensity.

  13. Compact acoustic refrigerator

    DOE Patents [OSTI]

    Bennett, G.A.

    1992-11-24T23:59:59.000Z

    A compact acoustic refrigeration system actively cools components, e.g., electrical circuits, in a borehole environment. An acoustic engine includes first thermodynamic elements for generating a standing acoustic wave in a selected medium. An acoustic refrigerator includes second thermodynamic elements located in the standing wave for generating a relatively cold temperature at a first end of the second thermodynamic elements and a relatively hot temperature at a second end of the second thermodynamic elements. A resonator volume cooperates with the first and second thermodynamic elements to support the standing wave. To accommodate the high heat fluxes required for heat transfer to/from the first and second thermodynamic elements, first heat pipes transfer heat from the heat load to the second thermodynamic elements and second heat pipes transfer heat from first and second thermodynamic elements to the borehole environment. 18 figs.

  14. Compact acoustic refrigerator

    DOE Patents [OSTI]

    Bennett, Gloria A. (Los Alamos, NM)

    1992-01-01T23:59:59.000Z

    A compact acoustic refrigeration system actively cools components, e.g., electrical circuits (22), in a borehole environment. An acoustic engine (12, 14) includes first thermodynamic elements (12) for generating a standing acoustic wave in a selected medium. An acoustic refrigerator (16, 26, 28) includes second thermodynamic elements (16) located in the standing wave for generating a relatively cold temperature at a first end of the second thermodynamic elements (16) and a relatively hot temperature at a second end of the second thermodynamic elements (16). A resonator volume (18) cooperates with the first and second thermodynamic elements (12, 16) to support the standing wave. To accommodate the high heat fluxes required for heat transfer to/from the first and second thermodynamic elements (12, 16), first heat pipes (24, 26) transfer heat from the heat load (22) to the second thermodynamic elements (16) and second heat pipes (28, 32) transfer heat from first and second thermodynamic elements (12, 16) to the borehole environment.

  15. Compact vacuum insulation embodiments

    DOE Patents [OSTI]

    Benson, D.K.; Potter, T.F.

    1992-04-28T23:59:59.000Z

    An ultra-thin compact vacuum insulation panel is comprised of two hard, but bendable metal wall sheets closely spaced apart from each other and welded around the edges to enclose a vacuum chamber. Glass or ceramic spacers hold the wall sheets apart. The spacers can be discrete spherical beads or monolithic sheets of glass or ceramic webs with nodules protruding therefrom to form essentially point' or line' contacts with the metal wall sheets. In the case of monolithic spacers that form line' contacts, two such spacers with the line contacts running perpendicular to each other form effectively point' contacts at the intersections. Corrugations accommodate bending and expansion, tubular insulated pipes and conduits, and preferred applications are also included. 26 figs.

  16. Compact vacuum insulation

    DOE Patents [OSTI]

    Benson, David K. (Golden, CO); Potter, Thomas F. (Denver, CO)

    1993-01-01T23:59:59.000Z

    An ultra-thin compact vacuum insulation panel is comprised of two hard, but bendable metal wall sheets closely spaced apart from each other and welded around the edges to enclose a vacuum chamber. Glass or ceramic spacers hold the wall sheets apart. The spacers can be discrete spherical beads or monolithic sheets of glass or ceramic webs with nodules protruding therefrom to form essentially "point" or "line" contacts with the metal wall sheets. In the case of monolithic spacers that form "line" contacts, two such spacers with the line contacts running perpendicular to each other form effectively "point" contacts at the intersections. Corrugations accommodate bending and expansion, tubular insulated pipes and conduits, and preferred applications are also included.

  17. Compact vacuum insulation

    DOE Patents [OSTI]

    Benson, D.K.; Potter, T.F.

    1993-01-05T23:59:59.000Z

    An ultra-thin compact vacuum insulation panel is comprised of two hard, but bendable metal wall sheets closely spaced apart from each other and welded around the edges to enclose a vacuum chamber. Glass or ceramic spacers hold the wall sheets apart. The spacers can be discrete spherical beads or monolithic sheets of glass or ceramic webs with nodules protruding therefrom to form essentially point'' or line'' contacts with the metal wall sheets. In the case of monolithic spacers that form line'' contacts, two such spacers with the line contacts running perpendicular to each other form effectively point'' contacts at the intersections. Corrugations accommodate bending and expansion, tubular insulated pipes and conduits, and preferred applications are also included.

  18. Compact vacuum insulation embodiments

    DOE Patents [OSTI]

    Benson, David K. (Golden, CO); Potter, Thomas F. (Denver, CO)

    1992-01-01T23:59:59.000Z

    An ultra-thin compact vacuum insulation panel is comprised of two hard, but bendable metal wall sheets closely spaced apart from each other and welded around the edges to enclose a vacuum chamber. Glass or ceramic spacers hold the wall sheets apart. The spacers can be discrete spherical beads or monolithic sheets of glass or ceramic webs with nodules protruding therefrom to form essentially "point" or "line" contacts with the metal wall sheets. In the case of monolithic spacers that form "line" contacts, two such spacers with the line contacts running perpendicular to each other form effectively "point" contacts at the intersections. Corrugations accommodate bending and expansion, tubular insulated pipes and conduits, and preferred applications are also included.

  19. Compact light source performance in recessed type luminaires

    SciTech Connect (OSTI)

    Hammer, E.E.

    1998-11-01T23:59:59.000Z

    Photometric comparisons were made with an indoor, recessed, type luminaire using incandescent, high intensity discharge and compact fluorescent lamps. The test results show substantial performance advantages, as expected, for the discharge light sources where the efficacy gains can be in the order for 400% even when including the ballast losses associated with the discharge lamps. The candlepower distribution patterns emerging from these luminaries are also different from those associated with the baseline incandescent lamps, and which are in some ways, even more desirable from a uniformity of illuminance perspective. A section on fluorescent lamp starting is also included which describes a system having excellent starting characteristics in terms of electrode starting temperature (RH/RC technique), proper operating frequency to minimize unwanted IR interactions, and satisfactory current crest factor values to help insure life performance.

  20. Use of a BCD for compaction control

    E-Print Network [OSTI]

    Li, Yanfeng

    2005-11-01T23:59:59.000Z

    Compaction of soil is essential in the construction of highways, airports, buildings, and bridges. Typically compaction is controlled by measuring the dry density and the water content of the compacted soil and checking that target values have been...

  1. Multiphoton Add fluorescent dye

    E-Print Network [OSTI]

    Braun, Paul

    in toluene was prepared at 0.96 w/w. The monomer used was trimethylolpropane triacrylate (TMPTA) (Aldrich in toluene; the toluene was removed by rotovapping. For fluorescence imaging in colloidal crystals the electro-optic modulator is used to regulate the power of the beam, selectively exposing the regions

  2. Optical Shelving: Suppressed Fluorescence

    E-Print Network [OSTI]

    Mould, R A

    2007-01-01T23:59:59.000Z

    The shelving phenomenon of quantum optics, originally observed by Dehmelt, is analyzed in terms of the nRules that are given in another paper. The heuristic value of these rules is apparent because they reveal the mechanism that enforces the suppression of fluorescence during the dark period associated with shelving.

  3. Optical Shelving: Suppressed Fluorescence

    E-Print Network [OSTI]

    Richard A Mould

    2011-04-11T23:59:59.000Z

    The shelving phenomenon of quantum optics, originally observed by Dehmelt, is analyzed in terms of the qRules that are given in another paper. The heuristic value of these rules is apparent because they not only describe the dark period during shelving, but they reveal the mechanism that enforces the suppression of fluorescence during that time.

  4. Fluorescent Protein Applications in Microscopy

    E-Print Network [OSTI]

    Straight, Aaron

    . The Identification of Green Fluorescent Protein III. Formation of the GFP Chromophore IV. The Structure of GFP V environment. II. The Identification of Green Fluorescent Protein The isolation of green fluorescent protein of Aequorea, Shimomura et al. noted that the lumines- cence from aequorin was blue rather than the green

  5. Compact vacuum insulation

    DOE Patents [OSTI]

    Benson, D.K.; Potter, T.F.

    1992-10-27T23:59:59.000Z

    Improved compact insulation panel is provided which is comprised of two adjacent metal sheets spaced close together with a plurality of spherical, or other discretely shaped, glass or ceramic beads optimally positioned between the sheets to provide support and maintain the spacing between the metal sheets when the gases there between are evacuated to form a vacuum. These spherical glass beads provide the maximum support while minimizing thermal conductance. In its preferred embodiment; these two metal sheets are textured with ribs or concave protrusions in conjunction with the glass beads to maximize the structural integrity of the panels while increasing the spacing between beads, thereby reducing the number of beads and the number of thermal conduction paths. Glass or porcelain-enameled liners in combination with the glass spacers and metal sidewalls effectively decrease thermal conductivity, and various laminates, including wood, porcelain-enameled metal, and others effectively increase the strength and insulation capabilities of the panels. Also, a metal web is provided to hold the spacers in place, and strategic grooves are shown to accommodate expansion and contraction or shaping of the panels. 35 figs.

  6. Compact vacuum insulation

    DOE Patents [OSTI]

    Benson, David K. (Golden, CO); Potter, Thomas F. (Denver, CO)

    1992-01-01T23:59:59.000Z

    Improved compact insulation panel is provided which is comprised of two adjacent metal sheets spaced close together with a plurality of spherical, or other discretely shaped, glass or ceramic beads optimally positioned between the sheets to provide support and maintain the spacing between the metal sheets when the gases therebetween are evacuated to form a vacuum. These spherical glass beads provide the maximum support while minimizing thermal conductance. In its preferred embodiment; these two metal sheets are textured with ribs or concave protrusions in conjunction with the glass beads to maximize the structural integrity of the panels while increasing the spacing between beads, thereby reducing the number of beads and the number of thermal conduction paths. Glass or porcelain-enameled liners in combination with the glass spacers and metal sidewalls effectively decrease thermal conductivity, and variious laminates, including wood, porcelain-enameled metal, and others effectively increase the strength and insulation capabilities of the panels. Also, a metal web is provided to hold the spacers in place, and strategic grooves are shown to accommodate expansion and contraction or shaping of the panels.

  7. Compact neutron generator

    DOE Patents [OSTI]

    Leung, Ka-Ngo; Lou, Tak Pui

    2005-03-22T23:59:59.000Z

    A compact neutron generator has at its outer circumference a toroidal shaped plasma chamber in which a tritium (or other) plasma is generated. A RF antenna is wrapped around the plasma chamber. A plurality of tritium ion beamlets are extracted through spaced extraction apertures of a plasma electrode on the inner surface of the toroidal plasma chamber and directed inwardly toward the center of neutron generator. The beamlets pass through spaced acceleration and focusing electrodes to a neutron generating target at the center of neutron generator. The target is typically made of titanium tubing. Water is flowed through the tubing for cooling. The beam can be pulsed rapidly to achieve ultrashort neutron bursts. The target may be moved rapidly up and down so that the average power deposited on the surface of the target may be kept at a reasonable level. The neutron generator can produce fast neutrons from a T-T reaction which can be used for luggage and cargo interrogation applications. A luggage or cargo inspection system has a pulsed T-T neutron generator or source at the center, surrounded by associated gamma detectors and other components for identifying explosives or other contraband.

  8. Renewable Surface Fluorescence Sandwich Immunoassay Biosensor...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Renewable Surface Fluorescence Sandwich Immunoassay Biosensor for Rapid Sensitive Botulinum Toxin Detection in an Automated Renewable Surface Fluorescence Sandwich Immunoassay...

  9. Single-molecule Fluorescence Spectroelectrochemistry of Cresyl...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Fluorescence Spectroelectrochemistry of Cresyl Violet. Abstract: We coupled scanning fluorescence microscopy with a potentiostat via a three-electrode electrochemical...

  10. Compaction managed mirror bend achromat

    DOE Patents [OSTI]

    Douglas, David (Yorktown, VA)

    2005-10-18T23:59:59.000Z

    A method for controlling the momentum compaction in a beam of charged particles. The method includes a compaction-managed mirror bend achromat (CMMBA) that provides a beamline design that retains the large momentum acceptance of a conventional mirror bend achromat. The CMMBA also provides the ability to tailor the system momentum compaction spectrum as desired for specific applications. The CMMBA enables magnetostatic management of the longitudinal phase space in Energy Recovery Linacs (ERLs) thereby alleviating the need for harmonic linearization of the RF waveform.

  11. The Air-Fluorescence Yield

    E-Print Network [OSTI]

    F. Arqueros; F. Blanco; D. Garcia-Pinto; M. Ortiz; J. Rosado

    2008-07-30T23:59:59.000Z

    Detection of the air-fluorescence radiation induced by the charged particles of extensive air showers is a well-established technique for the study of ultra-high energy cosmic rays. Fluorescence telescopes provide a nearly calorimetric measure of the primary energy. Presently the main source of systematic uncertainties comes from our limited accuracy in the fluorescence yield, that is, the number of fluorescence photons emitted per unit of energy deposited in the atmosphere by the shower particles. In this paper the current status of our knowledge on the fluorescence yield both experimental an theoretical will be discussed.

  12. New considerations for compact cyclotrons

    E-Print Network [OSTI]

    Marshall, Eric S. (Eric Scott)

    2012-01-01T23:59:59.000Z

    A compact cyclotron built with superconducting magnets could be a transformative solution to many scientific problems facing the defense, medical, and energy industries today. This thesis discusses three potential applications ...

  13. MESOSCALE SIMULATIONS OF POWDER COMPACTION

    SciTech Connect (OSTI)

    Lomov, Ilya; Fujino, Don; Antoun, Tarabay; Liu, Benjamin [Lawrence Livermore National Laboratory, P. O. Box 808, Livermore CA 94551 (United States)

    2009-12-28T23:59:59.000Z

    Mesoscale 3D simulations of shock compaction of metal and ceramic powders have been performed with an Eulerian hydrocode GEODYN. The approach was validated by simulating a well-characterized shock compaction experiment of a porous ductile metal. Simulation results using the Steinberg material model and handbook values for solid 2024 aluminum showed good agreement with experimental compaction curves and wave profiles. Brittle ceramic materials are not as well studied as metals, so a simple material model for solid ceramic (tungsten carbide) has been calibrated to match experimental compaction curves. Direct simulations of gas gun experiments with ceramic powders have been performed and showed good agreement with experimental data. The numerical shock wave profile has same character and thickness as that measured experimentally using VISAR. The numerical results show reshock states above the single-shock Hugoniot line as observed in experiments. We found that for good quantitative agreement with experiments 3D simulations are essential.

  14. Yellowstone River Compact (North Dakota)

    Broader source: Energy.gov [DOE]

    The Yellowstone River Compact, agreed to by the States of Montana, North Dakota, and Wyoming, provides for an equitable division and apportionment of the waters of the Yellowstone River, as well as...

  15. Magnetic fluorescent lamp

    DOE Patents [OSTI]

    Berman, S.M.; Richardson R.W.

    1983-12-29T23:59:59.000Z

    The radiant emission of a mercury-argon discharge in a fluorescent lamp assembly is enhanced by providing means for establishing a magnetic field with lines of force along the path of electron flow through the bulb of the lamp assembly, to provide Zeeman splitting of the ultraviolet spectral line. Optimum results are obtained when the magnetic field strength causes a Zeeman splitting of approximately 1.7 times the thermal line width.

  16. STORM/PALM - Super Resolution Fluorescence Microscope | EMSL

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    STORMPALM - Super Resolution Fluorescence Microscope STORMPALM - Super Resolution Fluorescence Microscope EMSL has developed and offers Fluorescence, Super Resolution STORM...

  17. Fluorescence analyzer for lignin

    SciTech Connect (OSTI)

    Berthold, John W. (Salem, OH); Malito, Michael L. (Hubbard, OH); Jeffers, Larry (Alliance, OH)

    1993-01-01T23:59:59.000Z

    A method and apparatus for measuring lignin concentration in a sample of wood pulp or black liquor comprises a light emitting arrangement for emitting an excitation light through optical fiber bundles into a probe which has an undiluted sensing end facing the sample. The excitation light causes the lignin concentration to produce fluorescent emission light which is then conveyed through the probe to analyzing equipment which measures the intensity of the emission light. Measures a This invention was made with Government support under Contract Number DOE: DE-FC05-90CE40905 awarded by the Department of Energy (DOE). The Government has certain rights in this invention.

  18. Fluorescent temperature sensor

    DOE Patents [OSTI]

    Baker, Gary A [Los Alamos, NM; Baker, Sheila N [Los Alamos, NM; McCleskey, T Mark [Los Alamos, NM

    2009-03-03T23:59:59.000Z

    The present invention is a fluorescent temperature sensor or optical thermometer. The sensor includes a solution of 1,3-bis(1-pyrenyl)propane within a 1-butyl-1-1-methylpyrrolidinium bis(trifluoromethylsulfonyl)imide ionic liquid solvent. The 1,3-bis(1-pyrenyl)propane remains unassociated when in the ground state while in solution. When subjected to UV light, an excited state is produced that exists in equilibrium with an excimer. The position of the equilibrium between the two excited states is temperature dependent.

  19. Compact orthogonal NMR field sensor

    DOE Patents [OSTI]

    Gerald, II, Rex E. (Brookfield, IL); Rathke, Jerome W. (Homer Glen, IL)

    2009-02-03T23:59:59.000Z

    A Compact Orthogonal Field Sensor for emitting two orthogonal electro-magnetic fields in a common space. More particularly, a replacement inductor for existing NMR (Nuclear Magnetic Resonance) sensors to allow for NMR imaging. The Compact Orthogonal Field Sensor has a conductive coil and a central conductor electrically connected in series. The central conductor is at least partially surrounded by the coil. The coil and central conductor are electrically or electro-magnetically connected to a device having a means for producing or inducing a current through the coil and central conductor. The Compact Orthogonal Field Sensor can be used in NMR imaging applications to determine the position and the associated NMR spectrum of a sample within the electro-magnetic field of the central conductor.

  20. Compact monolithic capacitive discharge unit

    DOE Patents [OSTI]

    Roesler, Alexander W. (Tijeras, NM); Vernon, George E. (Rio Rancho, NM); Hoke, Darren A. (Albuquerque, NM); De Marquis, Virginia K. (Tijeras, NM); Harris, Steven M. (Albuquerque, NM)

    2007-06-26T23:59:59.000Z

    A compact monolithic capacitive discharge unit (CDU) is disclosed in which a thyristor switch and a flyback charging circuit are both sandwiched about a ceramic energy storage capacitor. The result is a compact rugged assembly which provides a low-inductance current discharge path. The flyback charging circuit preferably includes a low-temperature co-fired ceramic transformer. The CDU can further include one or more ceramic substrates for enclosing the thyristor switch and for holding various passive components used in the flyback charging circuit. A load such as a detonator can also be attached directly to the CDU.

  1. Compact accelerator for medical therapy

    DOE Patents [OSTI]

    Caporaso, George J.; Chen, Yu-Jiuan; Hawkins, Steven A.; Sampayan, Stephen E.; Paul, Arthur C.

    2010-05-04T23:59:59.000Z

    A compact accelerator system having an integrated particle generator-linear accelerator with a compact, small-scale construction capable of producing an energetic (.about.70-250 MeV) proton beam or other nuclei and transporting the beam direction to a medical therapy patient without the need for bending magnets or other hardware often required for remote beam transport. The integrated particle generator-accelerator is actuable as a unitary body on a support structure to enable scanning of a particle beam by direction actuation of the particle generator-accelerator.

  2. Identification of Nucleotides with Identical Fluorescent Labels Based on Fluorescence

    E-Print Network [OSTI]

    Myrick, Michael Lenn

    Identification of Nucleotides with Identical Fluorescent Labels Based on Fluorescence Polarization for discriminating among the four DNA nucleotides la- beled identically with tetramethylrhodamine is described and demonstrated. Labeled nucleotides were dissolved in buffered surfactant solutions. In room temperature 4.5 m

  3. Mesoscale Simulations of Power Compaction

    SciTech Connect (OSTI)

    Lomov, I; Fujino, D; Antoun, T; Liu, B

    2009-08-06T23:59:59.000Z

    Mesoscale 3D simulations of metal and ceramic powder compaction in shock waves have been performed with an Eulerian hydrocode GEODYN. The approach was validated by simulating shock compaction of porous well-characterized ductile metal using Steinberg material model. Results of the simulations with handbook values for parameters of solid 2024 aluminum have good agreement with experimental compaction curves and wave profiles. Brittle ceramic materials are not so well studied as metals, so material model for ceramic (tungsten carbide) has been fitted to shock compression experiments of non-porous samples and further calibrated to match experimental compaction curves. Direct simulations of gas gun experiments with ceramic powder have been performed and showed good agreement with experimental data. Numerical shock wave profile has same character and thickness as measured with VISAR. Numerical results show reshock states above the single-shock Hugoniot line also observed in experiments. They found that to receive good quantitative agreement with experiment it is essential to perform 3D simulations.

  4. Interstate Oil and Gas Conservation Compact (Montana)

    Broader source: Energy.gov [DOE]

    This legislation authorizes the State to join the Interstate Compact for the Conservation of Oil and Gas. The Compact is an agreement that has been entered into by 30 oil- and gas-producing states,...

  5. Interstate Oil and Gas Conservation Compact (Maryland)

    Broader source: Energy.gov [DOE]

    This legislation authorizes the State to join the Interstate Compact for the Conservation of Oil and Gas. The Compact is an agreement that has been entered into by 30 oil- and gas-producing states,...

  6. Nuclear Resonance Fluorescence for Materials Assay

    E-Print Network [OSTI]

    Quiter, Brian

    2010-01-01T23:59:59.000Z

    clandestine material with nuclear resonance fluorescence”.E. Norman, UC Berkeley Dept. of Nuclear Engineering, privatepp. 349. G. Warren et al. “Nuclear Resonance Fluorescence of

  7. Compact neutron generator development at LBNL

    E-Print Network [OSTI]

    2003-01-01T23:59:59.000Z

    Generator Development at LBNL J. Reijonen, G. English, R.Technology Group in LBNL. The compact axial extraction

  8. United Nations Global Compact The UN Global Compact is a strategic policy initiative for

    E-Print Network [OSTI]

    Chatziantoniou, Damianos

    United Nations Global Compact The UN Global Compact is a strategic policy initiative for businesses in the world. The Global Compact pursues two complementary objectives: 1. Mainstream the ten principles the Millennium Development Goals (MDGs). Participation in the Global Compact is open to degree-granting academic

  9. Fluorescent fluid interface position sensor

    DOE Patents [OSTI]

    Weiss, Jonathan D.

    2004-02-17T23:59:59.000Z

    A new fluid interface position sensor has been developed, which is capable of optically determining the location of an interface between an upper fluid and a lower fluid, the upper fluid having a larger refractive index than a lower fluid. The sensor functions by measurement, of fluorescence excited by an optical pump beam which is confined within a fluorescent waveguide where that waveguide is in optical contact with the lower fluid, but escapes from the fluorescent waveguide where that waveguide is in optical contact with the upper fluid.

  10. Compact portable diffraction moire interferometer

    DOE Patents [OSTI]

    Deason, Vance A. (Shelley, ID); Ward, Michael B. (Idaho Falls, ID)

    1989-01-01T23:59:59.000Z

    A compact and portable moire interferometer used to determine surface deformations of an object. The improved interferometer is comprised of a laser beam, optical and fiber optics devices coupling the beam to one or more evanescent wave splitters, and collimating lenses directing the split beam at one or more specimen gratings. Observation means including film and video cameras may be used to view and record the resultant fringe patterns.

  11. Compact portable diffraction moire interferometer

    DOE Patents [OSTI]

    Deason, V.A.; Ward, M.B.

    1988-05-23T23:59:59.000Z

    A compact and portable moire interferometer used to determine surface deformations of an object. The improved interferometer is comprised of a laser beam, optical and fiber optics devices coupling the beam to one or more evanescent wave splitters, and collimating lenses directing the split beam at one or more specimen gratings. Observations means including film and video cameras may be used to view and record the resultant fringe patterns. 7 figs.

  12. Compact magnetic energy storage module

    DOE Patents [OSTI]

    Prueitt, Melvin L. (Los Alamos, NM)

    1994-01-01T23:59:59.000Z

    A superconducting compact magnetic energy storage module in which a plurality of superconducting toroids, each having a toroidally wound superconducting winding inside a poloidally wound superconducting winding, are stacked so that the flow of electricity in each toroidally wound superconducting winding is in a direction opposite from the direction of electrical flow in other contiguous superconducting toroids. This allows for minimal magnetic pollution outside of the module.

  13. Compact magnetic energy storage module

    DOE Patents [OSTI]

    Prueitt, M.L.

    1994-12-20T23:59:59.000Z

    A superconducting compact magnetic energy storage module in which a plurality of superconducting toroids, each having a toroidally wound superconducting winding inside a poloidally wound superconducting winding, are stacked so that the flow of electricity in each toroidally wound superconducting winding is in a direction opposite from the direction of electrical flow in other contiguous superconducting toroids. This allows for minimal magnetic pollution outside of the module. 4 figures.

  14. Compact Gamma-ray Source Technology Development Study

    SciTech Connect (OSTI)

    Anderson, S G; Gibson, D J; Rusnak, B

    2009-09-25T23:59:59.000Z

    This study focuses on the applicability of current accelerator and laser technologies to the construction of compact, narrow bandwidth, gamma-ray sources for DHS missions in illicit materials detection. It also identifies research and development areas in which advancement will directly benefit these light sources. In particular, we review the physics of Compton scattering based light sources and emphasize the source properties most important to Nuclear Resonance Fluorescence (NRF) applications of interest. The influences of laser and electron beam properties on the light source are examined in order to evaluate the utility of different technologies for this application. Applicable bulk and fiber-based laser systems and laser recirculation technologies are discussed and Radio Frequency (RF) Linear Accelerator (linac) technologies are examined to determine the optimal frequency and pulse formats achievable.

  15. Nuclear Resonance Fluorescence for Nuclear Materials Assay

    E-Print Network [OSTI]

    Quiter, Brian Joseph

    2010-01-01T23:59:59.000Z

    Potential of Nuclear Resonance Fluorescence . . . . . . . .2.9.1 Nuclear ThomsonSections . . . . . . . . . . . . . . . Nuclear Resonance

  16. GREEN FLUORESCENT PROTEIN The green revolution

    E-Print Network [OSTI]

    Stearns, Tim

    GREEN FLUORESCENT PROTEIN The green revolution Green fluorescent protein allows gene expression a fluorescent product when expressed. Just such a molecule, green fluorescent protein (GFP), has recently green light when disturbed (often seen when riding in a boat at night). In Aequorea, the green

  17. Compact

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645U.S. DOEThe Bonneville Power Administration would like submit the followingth Lomonosov1 COMMUNITY

  18. Fluorescence of molecular excimers

    SciTech Connect (OSTI)

    Nurmukhametov, R.N.; Sakhno, T.V.; Saukov, G.G.; Khakhel, O.A. [L. Ya. Karpov Research Physiochemical Institute, Moscow (Russian Federation)

    1995-11-01T23:59:59.000Z

    The phenomena of excimer fluorescence are most thoroughly studied in solutions of polycyclic aromatic hydrocarbons (PAHs). Therefore, excimer formation is usually treated with reference to molecules of this class of compounds. In the literature, only a qualitative picture of the energetics of excimer formation is given. It is assumed that dimerization of electron-excited and unexcited molecules is followed by the splitting of molecular electron-excited levels. PAH molecules are characterized by two lower excited levels: {sup 1}L{sub a} and {sup 1}L{sub b} (according to Platt`s classification). The S{sub 1}* state of some PAH compounds (e.g., naphthalene, phenanthrene, pyrene) is {sup 1}L{sub b}, while in other PAH (anthracene, naphthacene, perylene, etc.) it is the {sup 1}L{sub a} state. It is assumed that the {sup 1}L{sub a}-level is split more significantly than the {sup 1}L{sub b} level. Therefore, for all PAH investigated the excimer state is described as a lower-lying component of the split {sup 1}L{sub a} level. Quantum-chemical consideration of the splitting of electron levels of PAH molecules in excimers is undertaken. Unfortunately, in this case the description is also of a qualitative character. In the cited work, a correlation is noted between the energy of the {sup 1}L{sub a} state of the molecule and the wave number corresponding to the maximum of the emission band of the excimer. However, it does not give the wavelength of the maximum of the excimer band for some PAH, in other words, a definite dependence of the position of this band on molecular structure. The present work is devoted to a search for an answer to this question.

  19. The Cooling of Compact Stars

    E-Print Network [OSTI]

    Dany Page; Ulrich Geppert; Fridolin Weber

    2005-08-01T23:59:59.000Z

    The cooling of a compact star depends very sensitively on the state of dense matter at supranuclear densities, which essentially controls the neutrino emission, as well as on the structure of the stellar outer layers which control the photon emission. Open issues concern the hyperon population, the presence of meson condensates, superfluidity and superconductivity, and the transition of confined hadronic matter to quark matter. This paper describes these issues and presents cooling calculations based on a broad collection of equations of state for neutron star matter and strange matter. These results are tested against the body of observed cooling data.

  20. Two Piece Compaction Die Design

    SciTech Connect (OSTI)

    Coffey, Ethan N [ORNL

    2010-03-01T23:59:59.000Z

    Compaction dies used to create europium oxide and tantalum control plates were modeled using ANSYS 11.0. Two-piece designs were considered in order to make the dies easier to assemble than the five-piece dies that were previously used. The two areas of concern were the stresses at the interior corner of the die cavity and the distortion of the cavity wall due to the interference fit between the two pieces and the pressure exerted on the die during the compaction process. A successful die design would have stresses less than the yield stress of the material and a maximum wall distortion on the order of 0.0001 in. Design factors that were investigated include the inner corner radius, the value of the interference fit, the compaction force, the size of the cavity, and the outer radius and geometry of the outer ring. The results show that for the europium oxide die, a 0.01 in. diameter wire can be used to create the cavity, leading to a 0.0055 in. radius corner, if the radial interference fit is 0.003 in. For the tantalum die, the same wire can be used with a radial interference fit of 0.001 in. Also, for the europium oxide die with a 0.003 in. interference fit, it is possible to use a wire with a diameter of 0.006 in. for the wire burning process. Adding a 10% safety factor to the compaction force tends to lead to conservative estimates of the stresses but not for the wall distortion. However, when the 10% safety factor is removed, the wall distortion is not affected enough to discard the design. Finally, regarding the europium oxide die, when the cavity walls are increased by 0.002 in. per side or the outer ring is made to the same geometry as the tantalum die, all the stresses and wall distortions are within the desired range. Thus, the recommendation is to use a 0.006 in. diameter wire and a 0.003 in. interference fit for the europium oxide die and a 0.01 in. diameter wire and a 0.001 in. interference fit for the tantalum die. The dies can also be made to have the same outer geometry if desired.

  1. Compacted carbon for electrochemical cells

    DOE Patents [OSTI]

    Greinke, R.A.; Lewis, I.C.

    1997-10-14T23:59:59.000Z

    This invention provides compacted carbon that is useful in the electrode of an alkali metal/carbon electrochemical cell of improved capacity selected from the group consisting of: (a) coke having the following properties: (1) an x-ray density of at least 2.00 grams per cubic centimeters, (2) a closed porosity of no greater than 5%, and (3) an open porosity of no greater than 47%; and (b) graphite having the following properties: (1) an x-ray density of at least 2.20 grams per cubic centimeters, (2) a closed porosity of no greater than 5%, and (3) an open porosity of no greater than 25%. This invention also relates to an electrode for an alkali metal/carbon electrochemical cell comprising compacted carbon as described above and a binder. This invention further provides an alkali metal/carbon electrochemical cell comprising: (a) an electrode as described above, (b) a non-aqueous electrolytic solution comprising an organic aprotic solvent and an electrolytically conductive salt and an alkali metal, and (c) a counter electrode. 10 figs.

  2. Compact submanifolds supporting singular interactions

    SciTech Connect (OSTI)

    Kaynak, Burak Tevfik, E-mail: burak.kaynak@boun.edu.tr; Teoman Turgut, O., E-mail: turgutte@boun.edu.tr

    2013-12-15T23:59:59.000Z

    A quantum particle moving under the influence of singular interactions on embedded surfaces furnish an interesting example from the spectral point of view. In these problems, the possible occurrence of a bound-state is perhaps the most important aspect. Such systems can be introduced as quadratic forms and generically they do not require renormalization. Yet an alternative path through the resolvent is also beneficial to study various properties. In the present work, we address these issues for compact surfaces embedded in a class of ambient manifolds. We discover that there is an exact bound state solution written in terms of the heat kernel of the ambient manifold for a range of coupling strengths. Moreover, we develop techniques to estimate bounds on the ground state energy when several surfaces, each of which admits a bound state solution, coexist. -- Highlights: •Schrödinger operator with singular interactions supported on compact submanifolds. •Exact bound-state solution in terms of the heat kernel of the ambient manifold. •Generalization of the variational approach to a collection of submanifolds. •Existence of a lower bound for a unique ground state energy.

  3. Hydrostatic compaction of Microtherm HT.

    SciTech Connect (OSTI)

    Broome, Scott Thomas; Bauer, Stephen J.

    2010-09-01T23:59:59.000Z

    Two samples of jacketed Microtherm{reg_sign}HT were hydrostatically pressurized to maximum pressures of 29,000 psi to evaluate both pressure-volume response and change in bulk modulus as a function of density. During testing, each of the two samples exhibited large irreversible compactive volumetric strains with only small increases in pressure; however at volumetric strains of approximately 50%, the Microtherm{reg_sign}HT stiffened noticeably at ever increasing rates. At the maximum pressure of 29,000 psi, the volumetric strains for both samples were approximately 70%. Bulk modulus, as determined from hydrostatic unload/reload loops, increased by more than two-orders of magnitude (from about 4500 psi to over 500,000 psi) from an initial material density of {approx}0.3 g/cc to a final density of {approx}1.1 g/cc. An empirical fit to the density vs. bulk modulus data is K = 492769{rho}{sup 4.6548}, where K is the bulk modulus in psi, and {rho} is the material density in g/cm{sup 3}. The porosity decreased from 88% to {approx}20% indicating that much higher pressures would be required to compact the material fully.

  4. Compact approach to fusion power reactors

    SciTech Connect (OSTI)

    Hagenson, R.L.; Krakowski, R.A.; Bathke, C.G.; Miller, R.L.

    1984-01-01T23:59:59.000Z

    The potential of the Reversed-Field Pinch (RFP) for development into an efficient, compact, copper-coil fusion reactor has been quantified by comprehensive parametric tradeoff studies. These compact systems promise to be competitive in size, power density, and cost to alternative energy sources. Conceptual engineering designs that largely substantiate these promising results have since been completed. This 1000-MWe(net) design is described along with a detailed rationale and physics/technology assessment for the compact approach to fusion.

  5. Method for preparing porous metal hydride compacts

    DOE Patents [OSTI]

    Ron, M.; Gruen, D.M.; Mendelsohn, M.H.; Sheft, I.

    1980-01-21T23:59:59.000Z

    A method for preparing porous metallic-matrix hydride compacts which can be repeatedly hydrided and dehydrided without disintegration. A mixture of a finely divided metal hydride and a finely divided matrix metal is contacted with a poison which prevents the metal hydride from dehydriding at room temperature and atmospheric pressure. The mixture of matrix metal and poisoned metal hydride is then compacted under pressure at room temperature to form porous metallic-matrix hydride compacts.

  6. Method for preparing porous metal hydride compacts

    DOE Patents [OSTI]

    Ron, Moshe (Haifa, IL); Gruen, Dieter M. (Downers Grove, IL); Mendelsohn, Marshall H. (Woodridge, IL); Sheft, Irving (Oak Park, IL)

    1981-01-01T23:59:59.000Z

    A method for preparing porous metallic-matrix hydride compacts which can be repeatedly hydrided and dehydrided without disintegration. A mixture of a finely divided metal hydride and a finely divided matrix metal is contacted with a poison which prevents the metal hydride from dehydriding at room temperature and atmospheric pressure. The mixture of matrix metal and poisoned metal hydride is then compacted under pressure at room temperature to form porous metallic-matrix hydride compacts.

  7. Convolution type operators on locally compact groups

    E-Print Network [OSTI]

    Shtein--~erg, Convolution Type Operators on Locally Compact Groups [in Russian],. Manuscript Deposited in the All-Union Institute of Scientific and Technical ...

  8. Interstate Mining Compact Commission (multi-state)

    Broader source: Energy.gov [DOE]

    The Interstate Mining Compact is a multi-state governmental agency / organization that represents the natural resource and related environmental protection interests of its member states. Currently...

  9. Compact Solid State Cooling Systems: Compact MEMS Electrocaloric Module

    SciTech Connect (OSTI)

    None

    2010-10-01T23:59:59.000Z

    BEETIT Project: UCLA is developing a novel solid-state cooling technology to translate a recent scientific discovery of the so-called giant electrocaloric effect into commercially viable compact cooling systems. Traditional air conditioners use noisy, vapor compression systems that include a polluting liquid refrigerant to circulate within the air conditioner, absorb heat, and pump the heat out into the environment. Electrocaloric materials achieve the same result by heating up when placed within an electric field and cooling down when removed—effectively pumping heat out from a cooler to warmer environment. This electrocaloric-based solid state cooling system is quiet and does not use liquid refrigerants. The innovation includes developing nano-structured materials and reliable interfaces for heat exchange. With these innovations and advances in micro/nano-scale manufacturing technologies pioneered by semiconductor companies, UCLA is aiming to extend the performance/reliability of the cooling module.

  10. Phased array compaction cell for measurement of the transversely isotropic elastic properties of compacting sediments

    E-Print Network [OSTI]

    Nihei, K.T.

    2012-01-01T23:59:59.000Z

    compaction and chemical diagenesis on the microfabric andAt early stages of diagenesis, clay-rich sediments can

  11. Cooling of Color Superconducting Compact Stars

    E-Print Network [OSTI]

    David Blaschke

    2006-03-26T23:59:59.000Z

    We review the status of research on the cooling of compact stars, with emphasis on the influence of color superconducting quark matter phases. Although a consistent microscopic approach is not yet available, severe constraints on the phase structure of matter at high densities come from recent mass and cooling observations of compact stars.

  12. The Compressor: Concurrent, Incremental, and Parallel Compaction

    E-Print Network [OSTI]

    Petrank, Erez

    The Compressor: Concurrent, Incremental, and Parallel Compaction Haim Kermany Erez Petrank Dept non-intrusive compactor is still missing. In this paper we present the Compressor, a novel compaction, thereby allowing acceptable runs on large heaps. Furthermore, the Compressor is the first compactor

  13. Exploration of Compact Stellarators as Power Plants

    E-Print Network [OSTI]

    California at San Diego, University of

    Exploration of Compact Stellarators as Power Plants: Initial Results from ARIES-CS Study Farrokh, see: http://aries.ucsd.edu/ #12;Exploration and Optimization of Compact Stellarators as Power Plants in the context of power plant studies, e.g., particle loss Divertor (location, particle and energy distribution

  14. Compacted Soil Liner Interface Strength Importance

    E-Print Network [OSTI]

    Case Study Compacted Soil Liner Interface Strength Importance Timothy D. Stark, F.ASCE1 ; Hangseok interface is not the geomembrane (GM)/compacted low-permeability soil liner (LPSL) but a soil­soil interface placing the cover soil from bottom to top. DOI: 10.1061/(ASCE)GT.1943-5606 .0000556. © 2012 American

  15. Why Python? 1) readable, compact, simple syntax

    E-Print Network [OSTI]

    Spang, Rainer

    Starting with Python #12;Why Python? 1) readable, compact, simple syntax 2) documented 3) memory output shown using green text 5 True 27 10/19/2010 6 #12;Scope · Declarations are global · Cannot for usually compacter, while more general. for - doing X for each element of S. can simulate while loops

  16. Non-compact versions of Edwards' Theorem

    E-Print Network [OSTI]

    Gogus, Nihat G; Poletsky, Evgeny A

    2010-01-01T23:59:59.000Z

    Edwards' Theorem establishes duality between a convex cone in the space of continuous functions on a compact space and the set of representing or Jensen measures for this cone. In this paper we prove non-compact versions of this theorem.

  17. Covered Product Category: Fluorescent Ballasts

    Broader source: Energy.gov [DOE]

    FEMP provides acquisition guidance and federal efficiency requirements across a variety of product categories, including fluorescent ballasts, which is a FEMP designated product category. Federal laws and requirements mandate that agencies meet these efficiency requirements in all procurement and acquisition actions that are not specifically exempted by law.

  18. Covered Product Category: Fluorescent Luminaires

    Broader source: Energy.gov [DOE]

    FEMP provides acquisition guidance and Federal efficiency requirements across a variety of product categories, including fluorescent luminaires. Federal laws and requirements mandate that agencies meet these efficiency requirements in all procurement and acquisition actions that are not specifically exempted by law.

  19. DOE Withdraws the Energy Star Label from 34 Compact Fluorescent Light Bulbs

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels DataDepartment of Energy Your Density Isn't Your Destiny: Theof"WaveInteractionsMaterials | DepartmentEnergy Will Not| Department

  20. Critical considerations of pupil alignment to achieve open-loop control of MEMS deformable mirror in non-linear laser scanning fluorescence

    E-Print Network [OSTI]

    mechanism of the MEMS DM, a high resolution CMOS camera and a compact Shack-Hartmann wavefront sensor-Hartmann wavefront sensor 1. INTRODUCTION Nonlinear fluorescence microscopic imaging, with its unique advantages of intrinsic three dimensional optical sectioning ability, deep tissue penetration, and reduced photo

  1. Fluorescent Magnetic Nanoparticles for Biomedical Applications

    E-Print Network [OSTI]

    Candea, George

    Fluorescent Magnetic Nanoparticles for Biomedical Applications V.M.Dao, Dr. G. Coullerez, Dr. L, the main goal was to synthesize and to characterize novel fluorescent magnetic nanoparticles. These nanoparticles (NPs) involve superparamagnetic iron oxide nanoparticles (SPIONs), a fluorescently-labeled polymer

  2. A cryogenic fluorescence spectroscopic study of uranyl carbonate...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    fluorescence spectroscopic study of uranyl carbonate, phosphate, and oxyhydroxide minerals. A cryogenic fluorescence spectroscopic study of uranyl carbonate, phosphate, and...

  3. Compacting Plastic-Bonded Explosive Molding Powders to Dense Solids

    SciTech Connect (OSTI)

    B. Olinger

    2005-04-15T23:59:59.000Z

    Dense solid high explosives are made by compacting plastic-bonded explosive molding powders with high pressures and temperatures for extended periods of time. The density is influenced by manufacturing processes of the powders, compaction temperature, the magnitude of compaction pressure, pressure duration, and number of repeated applications of pressure. The internal density variation of compacted explosives depends on method of compaction and the material being compacted.

  4. Compact, electro-hydraulic, variable valve actuation system providing...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Compact, electro-hydraulic, variable valve actuation system providing variable lift, timing and duration to enable high efficiency engine combustion control Compact,...

  5. A compact tritium AMS system

    SciTech Connect (OSTI)

    Chiarappa, M L; Dingley, K H; Hamm, R W; Love, A H; Roberts, M L

    1999-09-23T23:59:59.000Z

    Tritium ({sup 3}H) is a radioisotope that is extensively utilized in biological and environmental research. For biological research, {sup 3}H is generally quantified by liquid scintillation counting requiring gram-sized samples and counting times of several hours. For environmental research, {sup 3}H is usually quantified by {sup 3}He in-growth which requires gram-sized samples and in-growth times of several months. In contrast, provisional studies at LLNL's Center for Accelerator Mass Spectrometry have demonstrated that Accelerator Mass Spectrometry (AMS) can be used to quantify {sup 3}H in milligram-sized biological samples with a 100 to 1000-fold improvement in detection limits when compared to scintillation counting. This increased sensitivity is expected to have great impact in the biological and environmental research community. However in order to make the {sup 3}H AMS technique more broadly accessible, smaller, simpler, and less expensive AMS instrumentation must be developed. To meet this need, a compact, relatively low cost prototype {sup 3}H AMS system has been designed and built based on a LLNL ion source/sample changer and an AccSys Technology, Inc. Radio Frequency Quadrupole (RFQ) linac. With the prototype system, {sup 3}/{sup 1}H ratios ranging from 1 x 10{sup -10} to 1 x 10{sup -13} have to be measured from milligram sized samples. With improvements in system operation and sample preparation methodology, the sensitivity limit of the system is expected to increase to approximately 1 x 10{sup -15}.

  6. Fluorescence based chemical sensors for corrosion detection

    SciTech Connect (OSTI)

    Johnson, R.E. [LeTourneau Univ., Longview, TX (United States). Dept. of Chemistry; Agarwala, V.S. [Naval Air Warfare Center Aircraft Div., Patuxent River, MD (United States)

    1997-12-01T23:59:59.000Z

    Several fluorescent materials have been identified as possible corrosion sensing coatings. These are either redox or metal ion complex materials. The redox materials are nonfluorescent in the reduced state and become fluorescent upon oxidation. Incorporated into paint coatings, they provide an early warning of corrosive conditions at the metal or alloy surface. The metal ion complex materials only fluoresce when the organic compound complexes with metal ions such as those generated in corrosion reactions. Fluorescent materials have been incorporated into paint coatings and on metal surfaces for the detection of corrosion. Oxine reacts with aluminum oxide on corroded aluminum to give a fluorescence that can be photographed in UV light. Several other materials were found to have good fluorescence but cannot be reversibly oxidized or reduced at the present time. More work will be done with these compounds as well as with Schiff bases to develop new fluorescent chemical sensing materials for smart coating on alloy surfaces.

  7. Fluorescent optical liquid level sensor

    DOE Patents [OSTI]

    Weiss, Jonathan D. (Albuquerque, NM)

    2001-01-01T23:59:59.000Z

    A liquid level sensor comprising a transparent waveguide containing fluorescent material that is excited by light of a first wavelength and emits at a second, longer wavelength. The upper end of the waveguide is connected to a light source at the first wavelength through a beveled portion of the waveguide such that the input light is totally internally reflected within the waveguide above an air/liquid interface in a tank but is transmitted into the liquid below this interface. Light is emitted from the fluorescent material only in those portions of the waveguide that are above the air/liquid interface, to be collected at the upper end of the waveguide by a detector that is sensitive only to the second wavelength. As the interface moves down in the tank, the signal strength from the detector will increase.

  8. A CMOS-compatible compact display

    E-Print Network [OSTI]

    Chen, Andrew R. (Andrew Raymond)

    2005-01-01T23:59:59.000Z

    Portable information devices demand displays with high resolution and high image quality that are increasingly compact and energy-efficient. Microdisplays consisting of a silicon CMOS backplane integrated with light ...

  9. Steady state compact toroidal plasma production

    DOE Patents [OSTI]

    Turner, William C. (Livermore, CA)

    1986-01-01T23:59:59.000Z

    Apparatus and method for maintaining steady state compact toroidal plasmas. A compact toroidal plasma is formed by a magnetized coaxial plasma gun and held in close proximity to the gun electrodes by applied magnetic fields or magnetic fields produced by image currents in conducting walls. Voltage supply means maintains a constant potential across the electrodes producing an increasing magnetic helicity which drives the plasma away from a minimum energy state. The plasma globally relaxes to a new minimum energy state, conserving helicity according to Taylor's relaxation hypothesis, and injecting net helicity into the core of the compact toroidal plasma. Controlling the voltage so as to inject net helicity at a predetermined rate based on dissipative processes maintains or increases the compact toroidal plasma in a time averaged steady state mode.

  10. Gravitational waves from merging compact binaries

    E-Print Network [OSTI]

    Hughes, Scott A.

    Largely motivated by the development of highly sensitive gravitational-wave detectors, our understanding of merging compact binaries and the gravitational waves they generate has improved dramatically in recent years. ...

  11. Southern States Energy Compact (Multiple States)

    Broader source: Energy.gov [DOE]

    The Southern States Energy Compact provides for the proper employment and conservation of energy, and for the employment of energy-related facilities, materials, and products, within the context of...

  12. Belle Fourche River Compact (South Dakota)

    Broader source: Energy.gov [DOE]

    The Belle Fourche River Compact, agreed to by South Dakota and Wyoming, seeks to provide for the most efficient use of the waters of the Belle Fourche River Basin for multiple purposes, and to...

  13. Compact reflective imaging spectrometer utilizing immersed gratings

    DOE Patents [OSTI]

    Chrisp, Michael P. (Danville, CA)

    2006-05-09T23:59:59.000Z

    A compact imaging spectrometer comprising an entrance slit for directing light, a first mirror that receives said light and reflects said light, an immersive diffraction grating that diffracts said light, a second mirror that focuses said light, and a detector array that receives said focused light. The compact imaging spectrometer can be utilized for remote sensing imaging spectrometers where size and weight are of primary importance.

  14. Compact binary mergers: an astrophysical perspective

    E-Print Network [OSTI]

    S. Rosswog

    2010-12-22T23:59:59.000Z

    This paper reviews the current understanding of double neutron star and neutron star black hole binaries. It addresses mainly (nuclear) astrophysics aspects of compact binary mergers and thus complements recent reviews that have emphasized the numerical relativity viewpoint. In particular, the paper discusses different channels to release neutron-rich matter into the host galaxy, connections between compact binary mergers and short Gamma-ray bursts and accompanying electromagnetic signals.

  15. Technology Selections for Cylindrical Compact Fabrication

    SciTech Connect (OSTI)

    Jeffrey A. Phillips

    2010-10-01T23:59:59.000Z

    A variety of process approaches are available and have been used historically for manufacture of cylindrical fuel compacts. The jet milling, fluid bed overcoating, and hot press compacting approach being adopted in the U.S. AGR Fuel Development Program for scale-up of the compacting process involves significant paradigm shifts from historical approaches. New methods are being pursued because of distinct advantages in simplicity, yield, and elimination of process mixed waste. Recent advances in jet milling technology allow simplified dry matrix powder preparation. The matrix preparation method is well matched with patented fluid bed powder overcoating technology recently developed for the pharmaceutical industry and directly usable for high density fuel particle matrix overcoating. High density overcoating places fuel particles as close as possible to their final position in the compact and is matched with hot press compacting which fully fluidizes matrix resin to achieve die fill at low compacting pressures and without matrix end caps. Overall the revised methodology provides a simpler process that should provide very high yields, improve homogeneity, further reduce defect fractions, eliminate intermediate grading and QC steps, and allow further increases in fuel packing fractions.

  16. Fluorescent Nanoparticles for Radiation DetectionFluorescent Nanoparticles

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645U.S. DOEThe Bonneville Power AdministrationField8,Dist.New MexicoFinancingProofWorking OutsideFluorescent Lightingfor

  17. Soil Quality Information Sheet Rangeland Soil Quality--Compaction

    E-Print Network [OSTI]

    Soil Quality Information Sheet Rangeland Soil Quality--Compaction USDA, Natural Resources Conservation Service May 2001 Rangeland Sheet 4 What is compaction? Soil compaction occurs when moist or wet soil aggregates are pressed together and the pore space between them is reduced. Compaction changes

  18. Compact Proof Certificates For Linear Logic Kaustuv Chaudhuri

    E-Print Network [OSTI]

    Chaudhuri, Kaustuv

    Compact Proof Certificates For Linear Logic Kaustuv Chaudhuri INRIA, France http://kaustuv.chaudhuri

  19. Saccharide sensing molecules having enhanced fluorescent properties

    DOE Patents [OSTI]

    Satcher Jr., Joe H.; Lane, Stephen M.; Darrow, Christopher B.; Cary, Douglas R.; Tran, Joe Anh

    2004-01-06T23:59:59.000Z

    The present invention provides formulae for fluorescent compounds that have a number of properties which make them uniquely suited for use in sensors of analytes such as saccharides. The advantageous fluorescent properties include favorable excitation wavelengths, emission wavelengths, fluorescence lifetimes, and photostability. Additional advantageous properties include enhanced aqueous solubility, as well as temperature and pH sensitivity. The compound comprises an aryl or a substituted phenyl botonic acid that acts as a substrate recognition component, a fluorescence switch component, and a fluorophore. Fluorescent compounds are described that are excited at wavelengths greater than 400 nm and emit at wavelengths greater than 450 nm, which is advantageous for optical transmission through skin. The fluorophore is typically selected from transition metal-ligand complexes and thiazine, oxazine, oxazone, or oxazine-one as well as anthracene compounds. The fluorescent compound can be immobilized in a glucose permeable biocompatible polymer matrix that is implantable below the skin.

  20. Scanning fluorescent microthermal imaging apparatus and method

    DOE Patents [OSTI]

    Barton, Daniel L. (Albuquerque, NM); Tangyunyong, Paiboon (Albuquerque, NM)

    1998-01-01T23:59:59.000Z

    A scanning fluorescent microthermal imaging (FMI) apparatus and method is disclosed, useful for integrated circuit (IC) failure analysis, that uses a scanned and focused beam from a laser to excite a thin fluorescent film disposed over the surface of the IC. By collecting fluorescent radiation from the film, and performing point-by-point data collection with a single-point photodetector, a thermal map of the IC is formed to measure any localized heating associated with defects in the IC.

  1. Scanning fluorescent microthermal imaging apparatus and method

    DOE Patents [OSTI]

    Barton, D.L.; Tangyunyong, P.

    1998-01-06T23:59:59.000Z

    A scanning fluorescent microthermal imaging (FMI) apparatus and method is disclosed, useful for integrated circuit (IC) failure analysis, that uses a scanned and focused beam from a laser to excite a thin fluorescent film disposed over the surface of the IC. By collecting fluorescent radiation from the film, and performing point-by-point data collection with a single-point photodetector, a thermal map of the IC is formed to measure any localized heating associated with defects in the IC. 1 fig.

  2. Laser-Stimulated Fluorescence in Paleontology

    E-Print Network [OSTI]

    Kaye, Thomas G.; Falk, Amanda Renee; Pittman, Michael; Sereno, Paul C.; Martin, Larry D.; Burnham, David A.; Gong, Enpu; Xu, Xing; Wang, Yinan

    2015-05-27T23:59:59.000Z

    . doi: 10.1371/journal.pone. 0009223 PMID: 20169153 8. Warren TS, Gleason S, Bostwick RC, Verbeek ER. Ultraviolet light and fluorescent minerals: under- standing, collecting and displaying fluorescent minerals. GemGuides Book. 1999. 9. Hibbs AR. Confocal... fake and genuine vertebrate fossils. Journal of Paleontological Techniques. 2008; 2:1–5. Laser-Stimulated Fluorescence in Paleontology PLOS ONE | DOI:10.1371/journal.pone.0125923 May 27, 2015 22 / 22 ...

  3. LED Replacements for Linear Fluorescent Lamps Webcast

    Broader source: Energy.gov [DOE]

    In this June 20, 2011 webcast on LED products marketed as replacements for linear fluorescent lamps, Jason Tuenge of the Pacific Northwest National Laboratory (PNNL) discussed current Lighting...

  4. Portable spotter for fluorescent contaminants on surfaces

    DOE Patents [OSTI]

    Schuresko, Daniel D. (Oak Ridge, TN)

    1980-01-01T23:59:59.000Z

    A portable fluorescence-based spotter for polynuclear aromatic hydrocarbon contamination on personnel and work area surfaces under ambient lighting conditions is provided. This instrument employs beam modulation and phase sensitive detection for discriminating between fluorescence from organic materials from reflected background light and inorganic fluorescent material. The device uses excitation and emission filters to provide differentiation between classes of aromatic organic compounds. Certain inorganic fluorescent materials, including heavy metal compounds, may also be distinguished from the organic compounds, despite both having similar optical properties.

  5. Strategy Guideline: Compact Air Distribution Systems

    SciTech Connect (OSTI)

    Burdick, A.

    2013-06-01T23:59:59.000Z

    This Strategy Guideline discusses the benefits and challenges of using a compact air distribution system to handle the reduced loads and reduced air volume needed to condition the space within an energy efficient home. Traditional systems sized by 'rule of thumb' (i.e., 1 ton of cooling per 400 ft2 of floor space) that 'wash' the exterior walls with conditioned air from floor registers cannot provide appropriate air mixing and moisture removal in low-load homes. A compact air distribution system locates the HVAC equipment centrally with shorter ducts run to interior walls, and ceiling supply outlets throw the air toward the exterior walls along the ceiling plane; alternatively, high sidewall supply outlets throw the air toward the exterior walls. Potential drawbacks include resistance from installing contractors or code officials who are unfamiliar with compact air distribution systems, as well as a lack of availability of low-cost high sidewall or ceiling supply outlets to meet the low air volumes with good throw characteristics. The decision criteria for a compact air distribution system must be determined early in the whole-house design process, considering both supply and return air design. However, careful installation of a compact air distribution system can result in lower material costs from smaller equipment, shorter duct runs, and fewer outlets; increased installation efficiencies, including ease of fitting the system into conditioned space; lower loads on a better balanced HVAC system, and overall improved energy efficiency of the home.

  6. FAA Fluorescent Penetrant Laboratory Inspections

    SciTech Connect (OSTI)

    WINDES,CONNOR L.; MOORE,DAVID G.

    2000-08-02T23:59:59.000Z

    The Federal Aviation Administration Airworthiness Assurance NDI Validation Center currently assesses the capability of various non-destructive inspection (NDI) methods used for analyzing aircraft components. The focus of one such exercise is to evaluate the sensitivity of fluorescent liquid penetrant inspection. A baseline procedure using the water-washable fluorescent penetrant method defines a foundation for comparing the brightness of low cycle fatigue cracks in titanium test panels. The analysis of deviations in the baseline procedure will determine an acceptable range of operation for the steps in the inspection process. The data also gives insight into the depth of each crack and which step(s) of the inspection process most affect penetrant sensitivities. A set of six low cycle fatigue cracks produced in 6.35-mm thick Ti-6Al-4V specimens was used to conduct the experiments to produce sensitivity data. The results will document the consistency of the crack readings and compare previous experiments to find the best parameters for water-washable penetrant.

  7. Cylindrically Symmetric Models of Anisotropic Compact Stars

    E-Print Network [OSTI]

    G. Abbas; Sumara Nazeer; M. A. Meraj

    2014-12-16T23:59:59.000Z

    In this paper we have discussed the possibility of forming anisotropic compact stars from cosmological constant as one of the competent candidates of dark energy with cylindrical symmetry. For this purpose, we have applied the analytical solution of Krori and Barua metric to a particular cylindrically symmetric spacetime. The unknown constants in Krori and Barua metric have been determined by using masses and radii of class of compact stars like 4$U$1820-30, Her X-1, SAX J 1808-3658. The properties of these stars have been analyzed in detail. In this setting the cosmological constant has been taken as a variable which depends on the radial coordinates. We have checked all the regularity conditions, stability and surface redshift of the compact stars 4$U$1820-30, Her X-1, SAX J 1808-3658.

  8. A novel fluorescence detection method for organosilanes

    SciTech Connect (OSTI)

    Yang, H.X.; Craw, M.T.; Depew, M.C.; Wan, J.K.S. (Queen's Univ., Kingston, Ontario (Canada))

    1989-02-01T23:59:59.000Z

    Quinones such as phenanthraquinone and anthraquinone react with organosilanes giving persistent, strongly fluorescent radicals. The reactions are photochemically initiated, rapid, and facile; detection of concentrations of silanes in the 10{sup {minus}7} M range are readily achieved. The staring materials do not fluorescence making the procedure simple, selective and specific.

  9. Remote vacuum compaction of compressible hazardous waste

    DOE Patents [OSTI]

    Coyne, M.J.; Fiscus, G.M.; Sammel, A.G.

    1998-10-06T23:59:59.000Z

    A system is described for remote vacuum compaction and containment of low-level radioactive or hazardous waste comprising a vacuum source, a sealable first flexible container, and a sealable outer flexible container for receiving one or more first flexible containers. A method for compacting low level radioactive or hazardous waste materials at the point of generation comprising the steps of sealing the waste in a first flexible container, sealing one or more first containers within an outer flexible container, breaching the integrity of the first containers, evacuating the air from the inner and outer containers, and sealing the outer container shut. 8 figs.

  10. Remote vacuum compaction of compressible hazardous waste

    DOE Patents [OSTI]

    Coyne, Martin J. (Pittsburgh, PA); Fiscus, Gregory M. (McMurray, PA); Sammel, Alfred G. (Pittsburgh, PA)

    1998-01-01T23:59:59.000Z

    A system for remote vacuum compaction and containment of low-level radioactive or hazardous waste comprising a vacuum source, a sealable first flexible container, and a sealable outer flexible container for receiving one or more first flexible containers. A method for compacting low level radioactive or hazardous waste materials at the point of generation comprising the steps of sealing the waste in a first flexible container, sealing one or more first containers within an outer flexible container, breaching the integrity of the first containers, evacuating the air from the inner and outer containers, and sealing the outer container shut.

  11. COMPACT ACCELERATOR CONCEPT FOR PROTON THERAPY

    SciTech Connect (OSTI)

    Caporaso, G; Sampayan, S; Chen, Y; Harris, J; Hawkins, S; Holmes, C; Krogh, M; Nelson, S; Nunnally, W; Paul, A; Poole, B; Rhodes, M; Sanders, D; Selenes, K; Sullivan, J; Wang, L; Watson, J

    2006-08-18T23:59:59.000Z

    A new type of compact induction accelerator is under development at the Lawrence Livermore National Laboratory that promises to increase the average accelerating gradient by at least an order of magnitude over that of existing induction machines. The machine is based on the use of high gradient vacuum insulators, advanced dielectric materials and switches and is being developed as a compact flash x-ray radiography source. Research describing an extreme variant of this technology aimed at proton therapy for cancer will be presented.

  12. Applications of Nuclear Resonance Fluorescence

    SciTech Connect (OSTI)

    Warren, Glen A.; Detwiler, Rebecca S.; Peplowski, Patrick N.

    2010-11-11T23:59:59.000Z

    Nuclear Resonance Fluorescence (NRF) has the potential of addressing a wide variety of applications, which require isotopic and/or elemental information about a sample. We have investigated a variety of non-proliferation applications that may be addressed by NRF. From these applications, we have selected two, measuring uranium enrichment in UF6 cylinders and material verification in dismantlement, to investigate in more detail. Analytical models have been developed to evaluate these applications, and test measurements have been conducted to validate those models. We found that it is unlikely with current technology to address the requirements for UF6 cylinder enrichment measurements. In contrast, NRF is a very promising approach for material verification for dismantlement.

  13. Hard X-ray Fluorescence Measurements of Heteroepitaxial Solid...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Hard X-ray Fluorescence Measurements of Heteroepitaxial Solid Oxide Fuel Cell Cathode Materials. Hard X-ray Fluorescence Measurements of Heteroepitaxial Solid Oxide Fuel Cell...

  14. Using Nuclear Resonance Fluorescence for Nondestructive Isotopic Analysis

    E-Print Network [OSTI]

    Ludewigt, Bernhard A.

    2010-01-01T23:59:59.000Z

    7, (1959) pp. 54. [12] B.J. Quiter, ``Nuclear ResonanceFluorescence for Nuclear Materials Assay,'' University ofclandestine material with nuclear resonance fluorescence,"

  15. Super-Resolution Fluorescence Nanoscopy Applied to Image Core...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Super-Resolution Fluorescence Nanoscopy Applied to Image Core-Shell Photoswitching Nanoparticles and their Self-Assemblies . Super-Resolution Fluorescence Nanoscopy Applied to...

  16. Three-dimensional x-ray fluorescence mapping of a gold nanoparticle-loaded phantom

    SciTech Connect (OSTI)

    Ren, Liqiang; Wu, Di; Li, Yuhua; Liu, Hong, E-mail: liu@ou.edu [Center for Bioengineering and School of Electrical and Computer Engineering, University of Oklahoma, Norman, Oklahoma 73019 (United States)] [Center for Bioengineering and School of Electrical and Computer Engineering, University of Oklahoma, Norman, Oklahoma 73019 (United States); Wang, Ge [Biomedical Imaging Cluster and Department of Biomedical Engineering, Rensselaer Polytechnic Institute, Troy, New York 12180 (United States)] [Biomedical Imaging Cluster and Department of Biomedical Engineering, Rensselaer Polytechnic Institute, Troy, New York 12180 (United States); Wu, Xizeng [Department of Radiology, University of Alabama, Birmingham, Alabama 35233 (United States)] [Department of Radiology, University of Alabama, Birmingham, Alabama 35233 (United States)

    2014-03-15T23:59:59.000Z

    Purpose : X-ray fluorescence (XRF) is a promising technique with sufficient specificity and sensitivity for identifying and quantifying features in small samples containing high atomic number (Z) materials such as iodine, gadolinium, and gold. In this study, the feasibility of applying XRF to early breast cancer diagnosis and treatment is studied using a novel approach for three-dimensional (3D) x-ray fluorescence mapping (XFM) of gold nanoparticle (GNP)-loaded objects in a physical phantom at the technical level. Methods : All the theoretical analysis and experiments are conducted under the condition of using x-ray pencil beam and a compactly integrated x-ray spectrometer. The penetrability of the fluorescence x-rays from GNPs is first investigated by adopting a combination of BR12 with 70 mm/50 mm in thickness on the excitation/emission path to mimic the possible position of tumor goldin vivo. Then, a physical phantom made of BR12 is designed to translate in 3D space with three precise linear stages and subsequently the step by step XFM scanning is performed. The experimental technique named as background subtraction is applied to isolate the gold fluorescence from each spectrum obtained by the spectrometer. Afterwards, the attenuations of both the incident primary x-ray beam with energies beyond the gold K-edge energy (80.725 keV) and the isolated gold K{sub ?} fluorescence x-rays (65.99 –69.80 keV) acquired after background subtraction are well calibrated, and finally the unattenuated K{sub ?} fluorescence counts are used to realize mapping reconstruction and to describe the linear relationship between gold fluorescence counts and corresponding concentration of gold solutions. Results : The penetration results show that the goldK{sub ?} fluorescence x-rays have sufficient penetrability for this phantom study, and the reconstructed mapping results indicate that both the spatial distribution and relative concentration of GNPs within the designed BR12 phantom can be well identified and quantified. Conclusions : Although the XFM method in this investigation is still studied at the technical level and is not yet practical for routinein vivo mapping tasks with GNPs, the current penetrability measurements and phantom study strongly suggest the feasibility to establish and develop a 3D XFM system.

  17. Preferential Path Profiling: Compactly Numbering Interesting Paths

    E-Print Network [OSTI]

    Chilimbi, Trishul

    preferential path profiling (PPP), that reduces the overhead of path profiling. PPP leverages the observation that most consumers of path profiles are only inter- ested in a subset of all program paths. PPP achieves produced by PPP. This compact path numbering enables our PPP implementation to record path information

  18. Compact range for variable-zone measurements

    DOE Patents [OSTI]

    Burnside, Walter D. (Columbus, OH); Rudduck, Roger C. (Columbus, OH); Yu, Jiunn S. (Albuquerque, NM)

    1988-01-01T23:59:59.000Z

    A compact range for testing antennas or radar targets includes a source for directing energy along a feedline toward a parabolic reflector. The reflected wave is a spherical wave with a radius dependent on the distance of the source from the focal point of the reflector.

  19. Compact Ultradense Objects in the Solar System

    E-Print Network [OSTI]

    J. Rafelski; Ch. Dietl; L. Labun

    2013-03-19T23:59:59.000Z

    We describe properties and gravitational interactions of meteor-mass and greater compact ultra dense objects with nuclear density or greater (CUDO s). We discuss possible enclosure of CUDO s in comets, stability of these objects on impact with the Earth and Sun and show that the hypothesis of a CUDO core helps resolve issues challenging the understanding of a few selected cometary impacts.

  20. A Global Compact to End Poverty

    E-Print Network [OSTI]

    A Global Compact to End Poverty Jeffrey Sachs on stabilisation, transition and weapons of mass progress. We can realistically envision a world without extreme poverty by the year 2025 because. Sachs, The End of Poverty, 2005. WORLD ECONOMICS · Vol. 6 · No. 4 · October­December 2005 11 Jeffrey D

  1. Pathway to a Compact SASE FEL Device

    E-Print Network [OSTI]

    Dattoli, G; Petrillo, V; Rau, J V; Sabia, E; Spassovsky, I; Biedron, S G; Einstein, J; Milton, S V

    2015-01-01T23:59:59.000Z

    Newly developed high peak power lasers have opened the possibilities of driving coherent light sources operating with laser plasma accelerated beams and wave undulators. We speculate on the combination of these two concepts and show that the merging of the underlying technologies could lead to new and interesting possibilities to achieve truly compact, coherent radiator devices.

  2. Southeast Interstate Low-Level Radioactive Waste Management Compact (multi-state)

    Broader source: Energy.gov [DOE]

    The Southeast Interstate Low-Level Radioactive Waste Management Compact is administered by the Compact Commission. The Compact provides for rotating responsibility for the region's low-level...

  3. Glucose sensing molecules having selected fluorescent properties

    DOE Patents [OSTI]

    Satcher, Jr., Joe H.; Lane, Stephen M.; Darrow, Christopher B.; Cary, Douglas R.; Tran, Joe Anh

    2004-01-27T23:59:59.000Z

    An analyte sensing fluorescent molecule that employs intramolecular electron transfer is designed to exhibit selected fluorescent properties in the presence of analytes such as saccharides. The selected fluorescent properties include excitation wavelength, emission wavelength, fluorescence lifetime, quantum yield, photostability, solubility, and temperature or pH sensitivity. The compound comprises an aryl or a substituted phenyl boronic acid that acts as a substrate recognition component, a fluorescence switch component, and a fluorophore. The fluorophore and switch component are selected such that the value of the free energy for electron transfer is less than about 3.0 kcal mol.sup.-1. Fluorescent compounds are described that are excited at wavelengths greater than 400 nm and emit at wavelengths greater than 450 nm, which is advantageous for optical transmission through skin. The fluorophore is typically selected from transition metal-ligand complexes and thiazine, oxazine, oxazone, or oxazine-one as well as anthracene compounds. The fluorescent compound can be immobilized in a glucose permeable biocompatible polymer matrix that is implantable below the skin.

  4. Hiding patterns with daylight fluorescent inks

    E-Print Network [OSTI]

    Romain Rossier; Roger D. Hersch; School Of Computer; Communication Sciences; Ecole Polytechnique; Fédérale Lausanne

    We propose a method for hiding patterns within printed images by making use of classical and of two daylight fluorescent magenta and yellow inks. Under the D65 illuminant we establish in the CIELAB space the gamut of a classical cmyk printer and the gamut of the same printer using a combination of classical inks with daylight fluorescent inks. These gamuts show that a significant part of the classical ink gamut can be reproduced by combining classical inks with daylight fluorescent inks. By printing parts of images with a combination of classical and daylight fluorescent inks instead of using classical inks only, we can hide security patterns within printed images. Under normal daylight, we do not see any difference between the parts printed with classical inks only and the parts printed with daylight fluorescent inks and classical inks. By changing the illumination, e.g. by viewing the printed image under a tungsten lamp or under a UV lamp, the daylight fluorescent inks change their colors and reveal the security pattern formed by combinations of classical inks and of daylight fluorescent inks.

  5. Photosystem II fluorescence lifetime imaging in avocado leaves: Contributions of the lutein-epoxide and violaxanthin cycles to fluorescence quenching

    E-Print Network [OSTI]

    Govindjee

    Photosystem II fluorescence lifetime imaging in avocado leaves: Contributions of the lutein a fluorescence were made on leaves of avocado plants to study whether rapidly reversible Dp

  6. Production, Cost, and Soil Compaction Estimates for Two Western Juniper

    E-Print Network [OSTI]

    Dodson, Beth

    , Crook County Soil and Water Conservation District, Prineville, OR 97754. ABSTRACT: Harvesting trialsProduction, Cost, and Soil Compaction Estimates for Two Western Juniper Extraction Systems, production rates, and soil compaction impacts of two systems for harvesting western juniper (Juniperus

  7. Fundamental building blocks for a compact optoelectronic neural network processor

    E-Print Network [OSTI]

    Ruedlinger, Benjamin Franklin, 1976-

    2003-01-01T23:59:59.000Z

    The focus of this thesis is interconnects within the Compact Optoelectronic Neural Network Processor. The goal of the Compact Optoelectronic Neural Network Processor Project (CONNPP) is to build a small, rugged neural ...

  8. A thermodynamic approach for compaction of asphaltic composites

    E-Print Network [OSTI]

    Koneru, Saradhi

    2009-05-15T23:59:59.000Z

    and Focus of Current Work . . . . . . . . . . . . . . 2 B. Outline of the Thesis . . . . . . . . . . . . . . . . . . . . . 3 C. Notations Used . . . . . . . . . . . . . . . . . . . . . . . . 4 II LITERATURE REVIEW... . . . . . . . . . . . . . . . . 8 b. Asphalt Binder . . . . . . . . . . . . . . . . . . . 8 C. Compaction Equipment . . . . . . . . . . . . . . . . . . . . 9 1. Field Compaction Equipment . . . . . . . . . . . . . . 9 a. Static Steel Wheel Rollers . . . . . . . . . . . . . 9 b...

  9. A study of compaction methods for lunar soil simulants

    E-Print Network [OSTI]

    Ekkad, Rama Varadarajan

    1993-01-01T23:59:59.000Z

    , compaction by vibration, compaction under vacuum pressure under the simultaneous effect of vibration are examined. Duc to the increasing confining pressure, the air voids decrease and the particles will be more closely packed, thus increasing the relative... density. The research will be used to identify a convenient method for compacting samples for laboratory digging experiments. The results of the research conclude that compaction by using vacuum and vibration produce results which can be used to predict...

  10. Probing the denatured state ensemble with fluorescence

    E-Print Network [OSTI]

    Alston, Roy Willis

    2004-09-30T23:59:59.000Z

    around the original tryptophan substitutions in RNase Sa. Regardless of the denaturant, ?max for the proteins and model compounds differed very little, 349.3 ± 1.2 nm. However, significant differences were observed in the fluorescence intensity at ?max...

  11. Fluorescence Imaging for Nuclear Arms Control Verification

    E-Print Network [OSTI]

    Feener, Jessica S

    2014-08-14T23:59:59.000Z

    treaties. Specifically, this technique uses fluorescence imaging to determine fissile material attributes in verifying, during the dismantlement process, an uncanned nuclear warhead or warhead component without revealing sensitive information. This could...

  12. Fluorescence-based optical glucose sensing 

    E-Print Network [OSTI]

    Meledeo, Michael Adam

    2002-01-01T23:59:59.000Z

    Previous studies have indicated that optical means of blood glucose detection are feasible and provide a minimally invasive alternative to current commercially available modalities. Fluorescence spectroscopy has shown promise in many examples...

  13. Using Nuclear Resonance Fluorescence for Nondestructive Isotopic Analysis

    E-Print Network [OSTI]

    Ludewigt, Bernhard A.

    2010-01-01T23:59:59.000Z

    spent fuel assay using Nuclear Resonance Fluorescence,” Annual Meeting of the Institute of Nuclear Materials Management,

  14. Multiplexed fluorescence detector system for capillary electrophoresis

    DOE Patents [OSTI]

    Yeung, E.S.; Taylor, J.A.

    1994-06-28T23:59:59.000Z

    A fluorescence detection system for capillary electrophoresis is provided wherein the detection system can simultaneously excite fluorescence and substantially simultaneously monitor separations in multiple capillaries. This multiplexing approach involves laser irradiation of a sample in a plurality of capillaries through optical fibers that are coupled individually with the capillaries. The array is imaged orthogonally through a microscope onto a charge-coupled device camera for signal analysis. 14 figures.

  15. Multiplexed fluorescence detector system for capillary electrophoresis

    DOE Patents [OSTI]

    Yeung, E.S.; Taylor, J.A.

    1996-03-12T23:59:59.000Z

    A fluorescence detection system for capillary electrophoresis is provided wherein the detection system can simultaneously excite fluorescence and substantially simultaneously monitor separations in multiple capillaries. This multiplexing approach involves laser irradiation of a sample in a plurality of capillaries through optical fibers that are coupled individually with the capillaries. The array is imaged orthogonally through a microscope onto a charge-coupled device camera for signal analysis. 14 figs.

  16. Final Technical Report - Development of a tunable diode laser induced fluorescence diagnostic for the Princeton magnetic nozzle experiment: West Virginia University and Princeton Plasma Physics Laboratory

    SciTech Connect (OSTI)

    Earl Scime

    2006-11-07T23:59:59.000Z

    This project involves the construction of a compact, portable, laser induced fluorescence (LIF) diagnostic for measurements of neutral helium, neutral argon, and argon ion velocity space distributions in a high density, steady state, helicon source. The project is collaborative effort between the Princeton Plasma Physics Laboratory (PPPL) and the West Virginia University (WVU) helicon source group. A key feature of the diagnostic system will be the use of tunable diode lasers instead of the tunable dye lasers typically used in LIF experiments.

  17. A laboratory investigation of vibratory compaction of dry soils

    E-Print Network [OSTI]

    Webster, Cecil Ray

    1984-01-01T23:59:59.000Z

    . Standard Compaction Curve for Soil 3 (CL) 48 49 50 53 54 56 25 Effect of Frequency Variation on the Time Required to Achieve I/2 inch (12. 7 mm) of Settlement 57 26. Foot Size Effects on Compaction of Various Soils 59 27. Effect of Frequency... on the Compaction of Soil 1 (SP) Using Two Different Feet 63 28. Effect of Frequency on the Compaction of Soil 1 (SP) Using the Semi-Circular Foot with Various Static Weights 64 29. Effect of Frequency on the Compaction of Soil 1 (SP) Using the 5 Inch Diameter...

  18. Compact x-ray source and panel

    DOE Patents [OSTI]

    Sampayon, Stephen E. (Manteca, CA)

    2008-02-12T23:59:59.000Z

    A compact, self-contained x-ray source, and a compact x-ray source panel having a plurality of such x-ray sources arranged in a preferably broad-area pixelized array. Each x-ray source includes an electron source for producing an electron beam, an x-ray conversion target, and a multilayer insulator separating the electron source and the x-ray conversion target from each other. The multi-layer insulator preferably has a cylindrical configuration with a plurality of alternating insulator and conductor layers surrounding an acceleration channel leading from the electron source to the x-ray conversion target. A power source is connected to each x-ray source of the array to produce an accelerating gradient between the electron source and x-ray conversion target in any one or more of the x-ray sources independent of other x-ray sources in the array, so as to accelerate an electron beam towards the x-ray conversion target. The multilayer insulator enables relatively short separation distances between the electron source and the x-ray conversion target so that a thin panel is possible for compactness. This is due to the ability of the plurality of alternating insulator and conductor layers of the multilayer insulators to resist surface flashover when sufficiently high acceleration energies necessary for x-ray generation are supplied by the power source to the x-ray sources.

  19. The compactness of presupernova stellar cores

    SciTech Connect (OSTI)

    Sukhbold, Tuguldur; Woosley, S. E., E-mail: sukhbold@ucolick.org [Department of Astronomy and Astrophysics, University of California, Santa Cruz, CA 95064 (United States)

    2014-03-01T23:59:59.000Z

    The success or failure of the neutrino-transport mechanism for producing a supernova in an evolved massive star is known to be sensitive not only to the mass of the iron core that collapses, but also to the density gradient in the silicon and oxygen shells surrounding that core. Here we study the systematics of a presupernova core's 'compactness' as a function of the mass of the star and the physics used in its calculation. Fine-meshed surveys of presupernova evolution are calculated for stars from 15 to 65 M {sub ?}. The metallicity and the efficiency of semiconvection and overshoot mixing are both varied and bare carbon-oxygen cores are explored as well as full hydrogenic stars. Two different codes, KEPLER and MESA, are used for the study. A complex interplay of carbon and oxygen burning, especially in shells, can cause rapid variations in the compactness for stars of very nearly the same mass. On larger scales, the distribution of compactness with main sequence mass is found to be robustly non-monotonic, implying islands of 'explodabilty,' particularly around 8-20 M {sub ?} and 25-30 M {sub ?}. The carbon-oxygen (CO) core mass of a presupernova star is a better, (though still ambiguous) discriminant of its core structure than the main sequence mass.

  20. The Evolution of Compact Binary Star Systems

    E-Print Network [OSTI]

    Konstantin Postnov; Lev Yungelson

    2014-03-21T23:59:59.000Z

    We review the formation and evolution of compact binary stars consisting of white dwarfs (WDs), neutron stars (NSs), and black holes (BHs). Mergings of compact binary stars are expected to be the most important sources for the forthcoming gravitational-wave (GW) astronomy. In the first part of the review, we discuss observational manifestations of close binary stars with NS and/or black components and their merger rate, crucial points in the formation and evolution of compact stars in binary systems, including the treatment of the natal kicks which NSs and BHs acquire during the core collapse of massive stars and the common envelope phase of binary evolution, which are most relevant to the merging rates of NS-NS, NS-BH and BH-BH binaries. The second part of the review is devoted mainly to formation and evolution of binary WDs and their observational manifestations, including their role as progenitors of cosmologically important thermonuclear SN Ia. We also consider AM CVn-stars which are thought to be the best verification binary GW sources for future low-frequency GW space interferometers.

  1. Ultratrace analysis of transuranic actinides by laser-induced fluorescence

    DOE Patents [OSTI]

    Miller, S.M.

    1983-10-31T23:59:59.000Z

    Ultratrace quantities of transuranic actinides are detected indirectly by their effect on the fluorescent emissions of a preselected fluorescent species. Transuranic actinides in a sample are coprecipitated with a host lattice material containing at least one preselected fluorescent species. The actinide either quenches or enhances the laser-induced fluorescence of the preselected fluorescent species. The degree of enhancement or quenching is quantitatively related to the concentration of actinide in the sample.

  2. A 32-channel photon counting module with embedded auto/cross-correlators for real-time parallel fluorescence correlation spectroscopy

    SciTech Connect (OSTI)

    Gong, S.; Labanca, I.; Rech, I.; Ghioni, M. [Dipartimento di Elettronica, Informazione e Bioingegneria, Politecnico di Milano, Piazza Leonardo da Vinci 32, 20133 Milano (Italy)

    2014-10-15T23:59:59.000Z

    Fluorescence correlation spectroscopy (FCS) is a well-established technique to study binding interactions or the diffusion of fluorescently labeled biomolecules in vitro and in vivo. Fast FCS experiments require parallel data acquisition and analysis which can be achieved by exploiting a multi-channel Single Photon Avalanche Diode (SPAD) array and a corresponding multi-input correlator. This paper reports a 32-channel FPGA based correlator able to perform 32 auto/cross-correlations simultaneously over a lag-time ranging from 10 ns up to 150 ms. The correlator is included in a 32 × 1 SPAD array module, providing a compact and flexible instrument for high throughput FCS experiments. However, some inherent features of SPAD arrays, namely afterpulsing and optical crosstalk effects, may introduce distortions in the measurement of auto- and cross-correlation functions. We investigated these limitations to assess their impact on the module and evaluate possible workarounds.

  3. Supercontinuum Stimulated Emission Depletion Fluorescence Lifetime Imaging

    SciTech Connect (OSTI)

    Lesoine, Michael; Bose, Sayantan; Petrich, Jacob; Smith, Emily

    2012-06-13T23:59:59.000Z

    Supercontinuum (SC) stimulated emission depletion (STED) fluorescence lifetime imaging is demonstrated by using time-correlated single-photon counting (TCSPC) detection. The spatial resolution of the developed STED instrument was measured by imaging monodispersed 40-nm fluorescent beads and then determining their fwhm, and was 36 ± 9 and 40 ± 10 nm in the X and Y coordinates, respectively. The same beads measured by confocal microscopy were 450 ± 50 and 430 ± 30 nm, which is larger than the diffraction limit of light due to underfilling the microscope objective. Underfilling the objective and time gating the signal were necessary to achieve the stated STED spatial resolution. The same fluorescence lifetime (2.0 ± 0.1 ns) was measured for the fluorescent beads by using confocal or STED lifetime imaging. The instrument has been applied to study Alexa Fluor 594-phalloidin labeled F-actin-rich projections with dimensions smaller than the diffraction limit of light in cultured cells. Fluorescence lifetimes of the actin-rich projections range from 2.2 to 2.9 ns as measured by STED lifetime imaging.

  4. ,,,"Incandescent","Standard Fluorescent","Compact Fluorescent","High-Intensity Discharge","Halogen"

    U.S. Energy Information Administration (EIA) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page onYou are now leaving Energy.gov You are now leaving Energy.gov YouKizildere IRaghurajiConventional Gasoline Sales toReformulated, Average0.9 Relative Standard Errors for Table98.

  5. ,,,"Incandescent","Standard Fluorescent","Compact Fluorescent","High-Intensity Discharge","Halogen"

    U.S. Energy Information Administration (EIA) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page onYou are now leaving Energy.gov You are now leaving Energy.gov YouKizildere IRaghurajiConventional Gasoline Sales toReformulated, Average0.9 Relative Standard Errors for Table98.B39.

  6. Compact Imaging Spectrometer Utilizing Immersed Gratings

    DOE Patents [OSTI]

    Chrisp, Michael P. (Danville, CA); Lerner, Scott A. (Corvallis, OR); Kuzmenko, Paul J. (Livermore, CA); Bennett, Charles L. (Livermore, CA)

    2006-03-21T23:59:59.000Z

    A compact imaging spectrometer with an immersive diffraction grating that compensates optical distortions. The imaging spectrometer comprises an entrance slit for transmitting light, a system for receiving the light and directing the light, an immersion grating, and a detector array. The entrance slit, the system for receiving the light, the immersion grating, and the detector array are positioned wherein the entrance slit transmits light to the system for receiving the light and the system for receiving the light directs the light to the immersion grating and the immersion grating receives the light and directs the light through an optical element to the detector array.

  7. Raytheon's next generation compact inline cryocooler architecture

    SciTech Connect (OSTI)

    Schaefer, B. R.; Bellis, L.; Ellis, M. J.; Conrad, T. [Raytheon Space and Airborne Systems, 2000 E. El Segundo Blvd., El Segundo, CA 90245 (United States)

    2014-01-29T23:59:59.000Z

    Since the 1970s, Raytheon has developed, built, tested and integrated high performance cryocoolers. Our versatile designs for single and multi-stage cryocoolers provide reliable operation for temperatures from 10 to 200 Kelvin with power levels ranging from 50 W to nearly 600 W. These advanced cryocoolers incorporate clearance seals, flexure suspensions, hermetic housings and dynamic balancing to provide long service life and reliable operation in all relevant environments. Today, sensors face a multitude of cryocooler integration challenges such as exported disturbance, efficiency, scalability, maturity, and cost. As a result, cryocooler selection is application dependent, oftentimes requiring extensive trade studies to determine the most suitable architecture. To optimally meet the needs of next generation passive IR sensors, the Compact Inline Raytheon Stirling 1-Stage (CI-RS1), Compact Inline Raytheon Single Stage Pulse Tube (CI-RP1) and Compact Inline Raytheon Hybrid Stirling/Pulse Tube 2-Stage (CI-RSP2) cryocoolers are being developed to satisfy this suite of requirements. This lightweight, compact, efficient, low vibration cryocooler combines proven 1-stage (RS1 or RP1) and 2-stage (RSP2) cold-head architectures with an inventive set of warm-end mechanisms into a single cooler module, allowing the moving mechanisms for the compressor and the Stirling displacer to be consolidated onto a common axis and in a common working volume. The CI cryocooler is a significant departure from the current Stirling cryocoolers in which the compressor mechanisms are remote from the Stirling displacer mechanism. Placing all of the mechanisms in a single volume and on a single axis provides benefits in terms of package size (30% reduction), mass (30% reduction), thermodynamic efficiency (>20% improvement) and exported vibration performance (?25 mN peak in all three orthogonal axes at frequencies from 1 to 500 Hz). The main benefit of axial symmetry is that proven balancing techniques and hardware can be utilized to null all motion along the common axis. Low vibration translates to better sensor performance resulting in simpler, more direct mechanical mounting configurations, eliminating the need for convoluted, expensive, massive, long lead damping hardware.

  8. Charlton Compact Power Ltd | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page onYou are now leaving Energy.gov You are now leaving Energy.gov You are beingZealand JumpConceptual Model, click here.Telluric Survey asWest,CEICharlotte County, Virginia:Vermont:Compact

  9. Compact Power Inc CPI | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page onYou are now leaving Energy.gov You are now leaving Energy.gov You are beingZealand JumpConceptual Model, clickInformationNew York:GovernorCommons Capital JumpCompact Power Inc CPI

  10. Fluorescence energy transfer enhancement in aluminum nanoapertures

    E-Print Network [OSTI]

    de Torres, Juan; Moparthi, Satish Babu; Grigoriev, Victor; Wenger, Jérome

    2015-01-01T23:59:59.000Z

    Zero-mode waveguides (ZMWs) are confining light into attoliter volumes, enabling single molecule fluorescence experiments at physiological micromolar concentrations. Among the fluorescence spectroscopy techniques that can be enhanced by ZMWs, F\\"{o}rster resonance energy transfer (FRET) is one of the most widely used in life sciences. Combining zero-mode waveguides with FRET provides new opportunities to investigate biochemical structures or follow interaction dynamics at micromolar concentration with single molecule resolution. However, prior to any quantitative FRET analysis on biological samples, it is crucial to establish first the influence of the ZMW on the FRET process. Here, we quantify the FRET rates and efficiencies between individual donor-acceptor fluorophore pairs diffusing in aluminum zero-mode waveguides. Aluminum ZMWs are important structures thanks to their commercial availability and the large literature describing their use for single molecule fluorescence spectroscopy. We also compare the ...

  11. Ultrabright fluorescent OLEDS using triplet sinks

    DOE Patents [OSTI]

    Zhang, Yifan; Forrest, Stephen R; Thompson, Mark

    2013-06-04T23:59:59.000Z

    A first device is provided. The first device further comprises an organic light emitting device. The organic light emitting device further comprises an anode, a cathode, and an emissive layer disposed between the anode and the cathode. The emissive layer further comprises an organic host compound, an organic emitting compound capable of fluorescent emission at room temperature, and an organic dopant compound. The triplet energy of the dopant compound is lower than the triplet energy of the host compound. The dopant compound does not strongly absorb the fluorescent emission of the emitting compound.

  12. Design, Syntheses and Applications of Fluorescent Dyes

    E-Print Network [OSTI]

    Wu, Liangxing

    2010-10-12T23:59:59.000Z

    .11. Normalized UV absorbance and fluorescence of 1h and the labeled streptavidin 1s in 0.1 M lithium phosphate buffer, pH 7.4 ..................... 54 3.1. Spectra of BODIPYs 9 in CH 2 Cl 2 ........................................................... 65...) ............................................................ 94 4.8. Dependence of electronic spectra of 15h on pH ..................................... 96 4.9. UV-Vis absorption and fluorescence spectra of rosamine 25 and 25 labeled avidin in 0.1 M phosphate buffer, pH 7...

  13. Compact solid source of hydrogen gas

    DOE Patents [OSTI]

    Kravitz, Stanley H.; Hecht, Andrew M.; Sylwester, Alan P.; Bell, Nelson S.

    2004-06-08T23:59:59.000Z

    A compact solid source of hydrogen gas, where the gas is generated by contacting water with micro-disperse particles of sodium borohydride in the presence of a catalyst, such as cobalt or ruthenium. The micro-disperse particles can have a substantially uniform diameter of 1-10 microns, and preferably about 3-5 microns. Ruthenium or cobalt catalytic nanoparticles can be incorporated in the micro-disperse particles of sodium borohydride, which allows a rapid and complete reaction to occur without the problems associated with caking and scaling of the surface by the reactant product sodium metaborate. A closed loop water management system can be used to recycle wastewater from a PEM fuel cell to supply water for reacting with the micro-disperse particles of sodium borohydride in a compact hydrogen gas generator. Capillary forces can wick water from a water reservoir into a packed bed of micro-disperse fuel particles, eliminating the need for using an active pump.

  14. Compact wavefunctions from compressed imaginary time evolution

    E-Print Network [OSTI]

    Jarrod R. McClean; Alán Aspuru-Guzik

    2014-09-25T23:59:59.000Z

    Simulation of quantum systems promises to deliver physical and chemical predictions for the frontiers of technology. Unfortunately, the exact representation of these systems is plagued by the exponential growth of dimension with the number of particles, or colloquially, the curse of dimensionality. The success of approximation methods has hinged on the relative simplicity of physical systems with respect to the exponentially complex worst case. Exploiting this relative simplicity has required detailed knowledge of the physical system under study. In this work, we introduce a general and efficient black box method for many-body quantum systems that utilizes technology from compressed sensing to find the most compact wavefunction possible without detailed knowledge of the system. It is a Multicomponent Adaptive Greedy Iterative Compression (MAGIC) scheme. No knowledge is assumed in the structure of the problem other than correct particle statistics. This method can be applied to many quantum systems such as spins, qubits, oscillators, or electronic systems. As an application, we use this technique to compute ground state electronic wavefunctions of hydrogen fluoride and recover 98% of the basis set correlation energy or equivalently 99.996% of the total energy with $50$ configurations out of a possible $10^7$. Building from this compactness, we introduce the idea of nuclear union configuration interaction for improving the description of reaction coordinates and use it to study the dissociation of hydrogen fluoride and the helium dimer.

  15. ROSAT Observations of Compact Groups of Galaxies

    E-Print Network [OSTI]

    P. Saracco; P. Ciliegi

    1994-12-15T23:59:59.000Z

    A search for X-ray emission from compact groups revealed detection from 8 out of the 12 HCG images extracted from the ROSAT public archive. For two of them the X-ray emission originates from galaxies in the group. On the contrary, three groups show an extended emission clearly caused by hot intracluster gas. A Raymond-Smith hot plasma model provides an excellent fit to the X-ray spectra. The estimated temperatures are distributed in a quite narrow range (from 0.73 to 0.92 keV) and are consistent, within the errors, with 0.9 keV. The luminosity ranging from 0.75 to $5.1\\cdot10^{42}$erg s$^{-1}$. The most relevant result is the low metal abundance surely detected in two of them and likely in a third that characterizes the hot gas cloud responsible for the X-ray emission. The data concerning the remaining 3 detected compact groups are not sufficient to discriminate with certainty between diffuse and/or point-like X-ray emission. However the results of the spectral analysis point to the presence of a hot gas again with low metal abundance.

  16. Strange Quark Matter and Compact Stars

    E-Print Network [OSTI]

    Fridolin Weber

    2004-09-27T23:59:59.000Z

    Astrophysicists distinguish between three different types of compact stars. These are white dwarfs, neutron stars, and black holes. The former contain matter in one of the densest forms found in the Universe which, together with the unprecedented progress in observational astronomy, make such stars superb astrophysical laboratories for a broad range of most striking physical phenomena. These range from nuclear processes on the stellar surface to processes in electron degenerate matter at subnuclear densities to boson condensates and the existence of new states of baryonic matter--like color superconducting quark matter--at supernuclear densities. More than that, according to the strange matter hypothesis strange quark matter could be more stable than nuclear matter, in which case neutron stars should be largely composed of pure quark matter possibly enveloped in thin nuclear crusts. Another remarkable implication of the hypothesis is the possible existence of a new class of white dwarfs. This article aims at giving an overview of all these striking physical possibilities, with an emphasis on the astrophysical phenomenology of strange quark matter. Possible observational signatures associated with the theoretically proposed states of matter inside compact stars are discussed as well. They will provide most valuable information about the phase diagram of superdense nuclear matter at high baryon number density but low temperature, which is not accessible to relativistic heavy ion collision experiments.

  17. Compact reactor/ORC power source

    SciTech Connect (OSTI)

    Meier, K.L.; Kirchner, W.L.; Willcutt, G.J.

    1986-01-01T23:59:59.000Z

    A compact power source that combines an organic Rankine Cycle (ORC) electric generator with a nuclear reactor heat source is being designed and fabricated. Incorporating existing ORC technology with proven reactor technology, the compact reactor/ORC power source offers high reliability while minimizing the need for component development. Thermal power at 125 kWt is removed from the coated particle fueled, graphite moderated reactor by heat pipes operating at 500/sup 0/C. Outside the reactor vessel and connected to the heat pipes are vaporizers in which the toluene ORC working fluid is heated to 370/sup 0/C. In the turbine-alternator-pump (TAP) combined-rotating unit, the thermal energy of the toluene is converted to 25 kWe of electric power. Lumped parameter systems analyses combined with a finite element thermal analysis have aided in the power source design. The analyses have provided assurance of reliable multiyear normal operation as well as full power operation with upset conditions, such as failed heat pipes and inoperative ORC vaporizers. Because of inherent high reliability, long life, and insensitivity to upset conditions, this power source is especially suited for use in remote, inaccessible locations where fuel delivery and maintenance costs are high. 10 refs.

  18. Tidal deformations of a spinning compact object

    E-Print Network [OSTI]

    Paolo Pani; Leonardo Gualtieri; Andrea Maselli; Valeria Ferrari

    2015-03-25T23:59:59.000Z

    The deformability of a compact object induced by a perturbing tidal field is encoded in the tidal Love numbers, which depend sensibly on the object's internal structure. These numbers are known only for static, spherically-symmetric objects. As a first step to compute the tidal Love numbers of a spinning compact star, here we extend powerful perturbative techniques to compute the exterior geometry of a spinning object distorted by an axisymmetric tidal field to second order in the angular momentum. The spin of the object introduces couplings between electric and magnetic deformations and new classes of induced Love numbers emerge. For example, a spinning object immersed in a quadrupolar, electric tidal field can acquire some induced mass, spin, quadrupole, octupole and hexadecapole moments to second order in the spin. The deformations are encoded in a set of inhomogeneous differential equations which, remarkably, can be solved analytically in vacuum. We discuss certain subtleties in defining the multipole moments of the central object, which are due to the difficulty in separating the tidal field from the linear response of the object in the solution. By extending the standard procedure to identify the linear response in the static case, we prove analytically that the Love numbers of a Kerr black hole remain zero to second order in the spin. As a by-product, we provide the explicit form for a slowly-rotating, tidally-deformed Kerr black hole to quadratic order in the spin, and discuss its geodesic and geometrical properties.

  19. Compaction of Norphlet sandstones, Rankin County, Mississippi

    SciTech Connect (OSTI)

    McBride, E.F.

    1987-09-01T23:59:59.000Z

    Fabric and porosity changes resulting from compaction were studied in sandstones from three cores sampled at depths between 15,900 and 22,500 ft. Point counts of 30 thin sections indicate that 0.4% of the rock volume was lost by ductile grain deformation and 3% by pressure solution at both grain contacts and at widely spaced stylolites. Pre-cement porosities of eolian sandstone range from 27 to 35% (mean = 29%), indicating that a total of from 10 to 18% porosity (mean = 16%) was lost by compaction (assuming 45% initial porosity). The difference between the total porosity loss and the sum of the other two processes is assumed to be the porosity lost by grain rearrangement (mean = 12.6%). The amount of pressure solution at grain contacts for each well is independent of depth, temperature, and amount of both quartz cement and total cement. Stylolites transect both grains and cements, which indicates they formed late in the diagenetic sequence. Silica released by pressure solution at quartz grain contacts could not be the sole source and was probably not even the major source of quartz cement in the formation, because cementation by quartz preceded the episode of strong pressure solution. In addition, the volume of silica released by pressure solution appears to have been inadequate to provide the volume of quartz cement present.

  20. Compact Stirling cooling of astronomical detectors

    E-Print Network [OSTI]

    Raskin, Gert; Pessemier, Wim; Padilla, Jesus Perez; Vandersteen, Jeroen

    2013-01-01T23:59:59.000Z

    MAIA, a three-channel imager targeting fast cadence photometry, was recently installed on the Mercator telescope (La Palma, Spain). This instrument observes a 9.4 x 14.1 arcmin field of view simultaneously in three color bands ($u$, $g$ and $r$), using three of the largest (un-) available frame-transfer CCDs, namely the 2k x 6k CCD42-C0 from e2v. As these detectors are housed in three separate cryostats, compact cooling devices are required that offer sufficient power to cool the large chips to a temperature of 165K. We explored a broad spectrum of cooling options and technologies to cool the MAIA detectors. Finally, compact free-piston Stirling coolers were selected, namely the CryoTel MT cryo-coolers from SUNPOWER, that can extract 5W of heat at a temperature of 77K. In this contribution we give details of the MAIA detector cooling solution. We also discuss the general usability of this type of closed-cycle cryo-coolers for astronomical detectors. They offer distinct advantages but the vibrations caused by ...

  1. advanced compact accelerator: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    of suitable neutron sources that are compactible with installation in a hospital enviroment. A low-energy accelerator-based neutron source has the potential for meeting...

  2. Compact heat exchangers for condensation applications: Yesterday, today and tomorrow

    SciTech Connect (OSTI)

    Panchal, C.B.

    1993-07-01T23:59:59.000Z

    Compact heat exchangers are being increasingly considered for condensation applications in the process, cryogenic, aerospace, power and refrigeration industries. In this paper, different configurations available for condensation applications are analyzed and the current state-of-the-knowledge for the design of compact condensers is evaluated. The key technical issues for the design and development of compact heat exchangers for condensation applications are analyzed and major advantages are identified. The experimental data and performance prediction methods reported in the literature are analyzed to evaluate the present design capabilities for different compact heat-exchanger configurations. The design flexibility is evaluated for the development of new condensation applications, including integration with other process equipment.

  3. Poroelastic damage rheology: Dilation, compaction, and failure of rocks

    E-Print Network [OSTI]

    Lyakhovsky, Vladimir

    Poroelastic damage rheology: Dilation, compaction, and failure of rocks Yariv Hamiel Institute December 2004; Published 26 January 2005. Hamiel, Y., V. Lyakhovsky, and A. Agnon (2005), Poroelastic

  4. Development, Test and Demonstration of a Cost-Effective, Compact...

    Broader source: Energy.gov (indexed) [DOE]

    taylor.pdf More Documents & Publications Development, Test and Demonstration of a Cost-Effective, Compact, Light-Weight, and Scalable High Temperature Inverter for HEVs, PHEVs, and...

  5. accreting compact stars: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    of the millisecond brightness oscillations from low mass X-ray binaries during thermonuclear bursts can provide us with important information about compact star parameters....

  6. Appalachian States Low-Level Radioactive Waste Compact (Maryland)

    Broader source: Energy.gov [DOE]

    This legislation authorizes Maryland's entrance into the Appalachian States Low-Level Radioactive Waste Compact, which seeks to promote interstate cooperation for the proper management and disposal...

  7. Cape Light Compact- Residential Energy Efficiency Rebate Program

    Broader source: Energy.gov [DOE]

    Cape Light Compact (CLC) offers a variety of financial incentives to customers for purchasing energy efficient residential equipment. Residential customers can take advantage of incentives on...

  8. Interstate Oil and Gas Conservation Compact (Multiple States)

    Broader source: Energy.gov [DOE]

    The Interstate Oil and Gas Compact Commission assists member states efficiently maximize oil and natural gas resources through sound regulatory practices while protecting the nation's health,...

  9. Western Interstate Nuclear Compact State Nuclear Policy (Multiple States)

    Broader source: Energy.gov [DOE]

    Legislation authorizes states' entrance into the Western Interstate Nuclear Compact, which aims to undertake the cooperation of participating states in deriving the optimum benefit from nuclear and...

  10. Southwestern Low-Level Radioactive Waste Disposal Compact (South Dakota)

    Broader source: Energy.gov [DOE]

    This legislation authorizes the state's entrance into the Southwestern Low-Level Radioactive Waste Disposal Compact, which provides for the cooperative management of low-level radioactive waste....

  11. CODED SPECTROSCOPY FOR ETHANOL DETECTION IN DIFFUSE, FLUORESCENT MEDIA

    E-Print Network [OSTI]

    ABSTRACT CODED SPECTROSCOPY FOR ETHANOL DETECTION IN DIFFUSE, FLUORESCENT MEDIA by Scott Thomas Mc FOR ETHANOL DETECTION IN DIFFUSE, FLUORESCENT MEDIA by Scott Thomas McCain Department of Electrical

  12. Modelling of a Fluorescent Lamp Plasma

    E-Print Network [OSTI]

    Eindhoven, Technische Universiteit

    Technische Universiteit Eindhoven, op gezag van de Rector Magnificus, prof.dr. R.A. van Santen, voor een TECHNISCHE UNIVERSITEIT EINDHOVEN Hartgers, Albertus Modelling of a Fluorescent Lamp Plasma / by Albertus Hartgers. - Eindhoven : Technische Universiteit Eindhoven, 2003. - Proefschrift. ISBN 90-386-1665-1 NUR 924

  13. Oil Classification with Fluorescence Spectroscopy Engineering Physics

    E-Print Network [OSTI]

    Oldenburg, Carl von Ossietzky Universität

    detected by these channels. The investigation used three methods to examine crude oil, heavy oil, sludge1 Oil Classification with Fluorescence Spectroscopy Engineering Physics Master of Engineering and classification of oil spills on water surfaces. It is an overview of the laser remote sensor technique

  14. DNA sequencing using fluorescence background electroblotting membrane

    DOE Patents [OSTI]

    Caldwell, Karin D. (Salt Lake City, UT); Chu, Tun-Jen (Salt Lake City, UT); Pitt, William G. (Orem, UT)

    1992-01-01T23:59:59.000Z

    A method for the multiplex sequencing on DNA is disclosed which comprises the electroblotting or specific base terminated DNA fragments, which have been resolved by gel electrophoresis, onto the surface of a neutral non-aromatic polymeric microporous membrane exhibiting low background fluorescence which has been surface modified to contain amino groups. Polypropylene membranes are preferably and the introduction of amino groups is accomplished by subjecting the membrane to radio or microwave frequency plasma discharge in the presence of an aminating agent, preferably ammonia. The membrane, containing physically adsorbed DNA fragments on its surface after the electroblotting, is then treated with crosslinking means such as UV radiation or a glutaraldehyde spray to chemically bind the DNA fragments to the membrane through said smino groups contained on the surface thereof. The DNA fragments chemically bound to the membrane are subjected to hybridization probing with a tagged probe specific to the sequence of the DNA fragments. The tagging may be by either fluorophores or radioisotopes. The tagged probes hybridized to said target DNA fragments are detected and read by laser induced fluorescence detection or autoradiograms. The use of aminated low fluorescent background membranes allows the use of fluorescent detection and reading even when the available amount of DNA to be sequenced is small. The DNA bound to the membrances may be reprobed numerous times.

  15. Text-Alternative Version: LED Replacements for Linear Fluorescent Lamps

    Broader source: Energy.gov [DOE]

    Below is the text-alternative version of the "LED Replacements for Linear Fluorescent Lamps" webcast, held June 20, 2011.

  16. Confocal, FLIM & Multi-Photon Fluorescence Microscope | EMSL

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    supports quantitative fluorescence resonance energy transfer (FRET) for investigating molecular interaction dynamics in living cells. The system also includes differential...

  17. Compact conscious animal positron emission tomography scanner

    DOE Patents [OSTI]

    Schyler, David J. (Bellport, NY); O'Connor, Paul (Bellport, NY); Woody, Craig (Setauket, NY); Junnarkar, Sachin Shrirang (Sound Beach, NY); Radeka, Veljko (Bellport, NY); Vaska, Paul (Sound Beach, NY); Pratte, Jean-Francois (Stony Brook, NY); Volkow, Nora (Chevy Chase, MD)

    2006-10-24T23:59:59.000Z

    A method of serially transferring annihilation information in a compact positron emission tomography (PET) scanner includes generating a time signal for an event, generating an address signal representing a detecting channel, generating a detector channel signal including the time and address signals, and generating a composite signal including the channel signal and similarly generated signals. The composite signal includes events from detectors in a block and is serially output. An apparatus that serially transfers annihilation information from a block includes time signal generators for detectors in a block and an address and channel signal generator. The PET scanner includes a ring tomograph that mounts onto a portion of an animal, which includes opposing block pairs. Each of the blocks in a block pair includes a scintillator layer, detection array, front-end array, and a serial encoder. The serial encoder includes time signal generators and an address signal and channel signal generator.

  18. Compact and highly efficient laser pump cavity

    DOE Patents [OSTI]

    Chang, Jim J. (Dublin, CA); Bass, Isaac L. (Castro Valley, CA); Zapata, Luis E. (Livermore, CA)

    1999-01-01T23:59:59.000Z

    A new, compact, side-pumped laser pump cavity design which uses non-conventional optics for injection of laser-diode light into a laser pump chamber includes a plurality of elongated light concentration channels. In one embodiment, the light concentration channels are compound parabolic concentrators (CPC) which have very small exit apertures so that light will not escape from the pumping chamber and will be multiply reflected through the laser rod. This new design effectively traps the pump radiation inside the pump chamber that encloses the laser rod. It enables more uniform laser pumping and highly effective recycle of pump radiation, leading to significantly improved laser performance. This new design also effectively widens the acceptable radiation wavelength of the diodes, resulting in a more reliable laser performance with lower cost.

  19. Cooldown of the Compact Ignition Tokamak

    SciTech Connect (OSTI)

    Keeton, D.C.

    1987-08-01T23:59:59.000Z

    Cooldown of the Compact Ignition Tokamak (CIT) with the baseline liquid nitrogen cooling system was analyzed. On the basis of this analysis and present knowledge of the two-phase heat transfer, the current baseline CIT can be cooled down in about 1.5 h. An extensive heat transfer test program is recommended to reduce uncertainty in the heat transfer performance and to explore methods for minimizing the cooldown time. An alternate CIT cooldown system is described which uses a pressurized gaseous helium coolant in a closed-loop system. It is shown analytically that this system will cool down the CIT well within 1 h. Confidence in this analysis is sufficiently high that a heat transfer test program would not be necessary. The added cost of this alternate system is estimated to be about $5.3 million. This helium cooling system represents a reasonable backup approach to liquid nitrogen cooling of the CIT. 3 refs., 12 figs., 3 tabs.

  20. Collective Deceleration: Toward a Compact Beam Dump

    SciTech Connect (OSTI)

    Wu, H.-C.; /Munich, Max Planck Inst. Quantenopt.; Tajima, T.; Habs, D.; /Munich, Max Planck Inst. Quantenopt. /Munich U.; Chao, A.W.; /SLAC; Meyer-ter-Vehn, J.; /Munich, Max Planck Inst. Quantenopt.

    2011-11-28T23:59:59.000Z

    With the increasing development of laser accelerators, the electron energy is already beyond GeV and even higher in near future. Conventional beam dump based on ionization or radiation loss mechanism is cumbersome and costly, also has radiological hazards. We revisit the stopping power of high-energy charged particles in matter and discuss the associated problem of beam dump from the point of view of collective deceleration. The collective stopping length in an ionized gas can be several orders of magnitude shorter than the Bethe-Bloch and multiple electromagnetic cascades stopping length in solid. At the mean time, the tenuous density of the gas makes the radioactivation negligible. Such a compact and non-radioactivating beam dump works well for short and dense bunches, which is typically generated from laser wakefield accelerator.

  1. Compact hydrogen/helium isotope mass spectrometer

    DOE Patents [OSTI]

    Funsten, Herbert O. (Los Alamos, NM); McComas, David J. (Los Alamos, NM); Scime, Earl E. (Morgantown, WV)

    1996-01-01T23:59:59.000Z

    The compact hydrogen and helium isotope mass spectrometer of the present invention combines low mass-resolution ion mass spectrometry and beam-foil interaction technology to unambiguously detect and quantify deuterium (D), tritium (T), hydrogen molecule (H.sub.2, HD, D.sub.2, HT, DT, and T.sub.2), .sup.3 He, and .sup.4 He concentrations and concentration variations. The spectrometer provides real-time, high sensitivity, and high accuracy measurements. Currently, no fieldable D or molecular speciation detectors exist. Furthermore, the present spectrometer has a significant advantage over traditional T detectors: no confusion of the measurements by other beta-emitters, and complete separation of atomic and molecular species of equivalent atomic mass (e.g., HD and .sup.3 He).

  2. Compact high voltage solid state switch

    DOE Patents [OSTI]

    Glidden, Steven C.

    2003-09-23T23:59:59.000Z

    A compact, solid state, high voltage switch capable of high conduction current with a high rate of current risetime (high di/dt) that can be used to replace thyratrons in existing and new applications. The switch has multiple thyristors packaged in a single enclosure. Each thyristor has its own gate drive circuit that circuit obtains its energy from the energy that is being switched in the main circuit. The gate drives are triggered with a low voltage, low current pulse isolated by a small inexpensive transformer. The gate circuits can also be triggered with an optical signal, eliminating the trigger transformer altogether. This approach makes it easier to connect many thyristors in series to obtain the hold off voltages of greater than 80 kV.

  3. Compact imaging spectrometer utilizing immersed gratings

    DOE Patents [OSTI]

    Chrisp, Michael P. (Danville, CA); Lerner, Scott A. (Corvallis, OR); Kuzmenko, Paul J. (Livermore, CA); Bennett, Charles L. (Livermore, CA)

    2007-07-03T23:59:59.000Z

    A compact imaging spectrometer with an immersive diffraction grating that compensates optical distortions. The imaging spectrometer comprises an entrance slit for transmitting light, means for receiving the light and directing the light, an immersion grating, and a detector array. The entrance slit, the means for receiving the light, the immersion grating, and the detector array are positioned wherein the entrance slit transmits light to the means for receiving the light and the means for receiving the light directs the light to the immersion grating and the immersion grating receives the light and directs the light to the means for receiving the light, and the means for receiving the light directs the light to the detector array.

  4. Compact microwave ion source for industrial applications

    SciTech Connect (OSTI)

    Cho, Yong-Sub; Kim, Dae-Il; Kim, Han-Sung; Seol, Kyung-Tae; Kwon, Hyeok-Jung; Hong, In-Seok [Proton Engineering Frontier Project, Korea Atomic Energy Research Institute, Daejeon 305-353 (Korea, Republic of)

    2012-02-15T23:59:59.000Z

    A 2.45 GHz microwave ion source for ion implanters has many good properties for industrial application, such as easy maintenance and long lifetime, and it should be compact for budget and space. But, it has a dc current supply for the solenoid and a rf generator for plasma generation. Usually, they are located on high voltage platform because they are electrically connected with beam extraction power supply. Using permanent magnet solenoid and multi-layer dc break, high voltage deck and high voltage isolation transformer can be eliminated, and the dose rate on targets can be controlled by pulse duty control with semiconductor high voltage switch. Because the beam optics does not change, beam transfer components, such as focusing elements and beam shutter, can be eliminated. It has shown the good performances in budget and space for industrial applications of ion beams.

  5. Stirling Air Conditioner for Compact Cooling

    SciTech Connect (OSTI)

    None

    2010-09-01T23:59:59.000Z

    BEETIT Project: Infinia is developing a compact air conditioner that uses an unconventional high efficient Stirling cycle system (vs. conventional vapor compression systems) to produce cool air that is energy efficient and does not rely on polluting refrigerants. The Stirling cycle system is a type of air conditioning system that uses a motor with a piston to remove heat to the outside atmosphere using a gas refrigerant. To date, Stirling systems have been expensive and have not had the right kind of heat exchanger to help cool air efficiently. Infinia is using chip cooling technology from the computer industry to make improvements to the heat exchanger and improve system performance. Infinia’s air conditioner uses helium gas as refrigerant, an environmentally benign gas that does not react with other chemicals and does not burn. Infinia’s improvements to the Stirling cycle system will enable the cost-effective mass production of high-efficiency air conditioners that use no polluting refrigerants.

  6. Potential Environmental Impacts from the Metals in Incandescent, Compact Fluorescent Lamp (CFL), and Light-Emitting Diode (LED)

    E-Print Network [OSTI]

    Short, Daniel

    the lighting products are to be categorized as hazardous waste under existing U.S. federal and California state in lighting products without compromising their performance and useful lifespan. INTRODUCTION The U.S. Energy to increase energy efficiency for general lighting. Therefore, consumers are replacing incandescent light

  7. Measurement and model assessment of fluorescence lifetime sensing in multiply scattering media 

    E-Print Network [OSTI]

    Kuwana, Eddy

    2005-08-29T23:59:59.000Z

    fluorescence sensor and the reliability of fluorescence lifetime measurement verify the prospect of this technology for implantable purposes....

  8. Synonymous Address Compaction for Energy Reduction in Data TLB

    E-Print Network [OSTI]

    Lee, Hsien-Hsin "Sean"

    Synonymous Address Compaction for Energy Reduction in Data TLB Chinnakrishnan S. Ballapuram chinnak and Computer Engineering College of Computing Georgia Institute of Technology, Atlanta, GA 30332 ABSTRACT-cycle compaction of address translation requests in order to save energy in the data TLB. Our results show

  9. compactness in transport theory Mustapha Mokhtar-Kharroubi

    E-Print Network [OSTI]

    Boyer, Edmond

    A main feature of spectra of transport operators in nuclear reactor theory relies on the compactness (orOn L1 compactness in transport theory Mustapha Mokhtar-Kharroubi Département de Mathématiques spectral theory of neutron transport equations on both n-dimensional torus and spatial domains with ...nite

  10. THE ARIES-CS COMPACT STELLARATOR FUSION POWER PLANT

    E-Print Network [OSTI]

    Raffray, A. René

    THE ARIES-CS COMPACT STELLARATOR FUSION POWER PLANT F. NAJMABADI* and A. R. RAFFRAY Center stellarator power plants, ARIES-CS, has been conducted to explore attrac- tive compact stellarator by earlier stellarator power plant studies had led to cost projections much higher than those of the advanced

  11. The Size of Compact Extra Dimensions from Blackbody Radiation Laws

    E-Print Network [OSTI]

    Ramaton Ramos; Henrique Boschi-Filho

    2014-04-28T23:59:59.000Z

    In this work we generalize the Stefan-Boltzmann and Wien's displacement laws for a $D$-dimensional manifold composed by 4 non-compact dimensions and $D-4$ compact dimensions, $ R^{1,3}$ x $T^{D-4} $. The electromagnetic field is assumed to pervade all compact and non-compact dimensions. In particular, the total radiated power becomes $ R(T) = \\sigma_B T^4 + \\sigma_D (a) \\, T^D $, where $a$ is the size of the compact extra dimensions. For $D=10$, predicted from String Theory, and $D=11$, from M-Theory, the outcomes agree with available experimental data for $a$ as high as 2 x $10^{-7}$m.

  12. Modeling compaction-induced energy dissipation of granular HMX

    SciTech Connect (OSTI)

    Gonthier, K.A. [Lamar Univ., Beaumont, TX (US). Dept. of Mechanical Engineering; Menikoff, R.; Son, S.F.; Asay, B.W. [Los Alamos National Lab., NM (US)

    1998-12-31T23:59:59.000Z

    A thermodynamically consistent model is developed for the compaction of granular solids. The model is an extension of the single phase limit of two-phase continuum models used to describe Deflagration-to-Detonation Transition (DDT) experiments. The focus is on the energetics and dissipation of the compaction process. Changes in volume fraction are partitioned into reversible and irreversible components. Unlike conventional DDT models, the model is applicable from the quasi-static to dynamic compaction regimes for elastic, plastic, or brittle materials. When applied to the compaction of granular HMX (a brittle material), the model predicts results commensurate with experiments including stress relaxation, hysteresis, and energy dissipation. The model provides a suitable starting point for the development of thermal energy localization sub-scale models based on compaction-induced dissipation.

  13. COMPACTION OF FIBERBOARD OVERPACK MATERIALS IN A 9975 SHIPPING PACKAGE

    SciTech Connect (OSTI)

    Stefek, T.; Daugherty, W.; Estochen, E.; Murphy, J.

    2010-05-27T23:59:59.000Z

    Compaction of lower layers in the 9975 fiberboard overpack has been observed in packages that contain excess moisture. Dynamic loading of the package during transportation may also contribute to compaction of the fiberboard. This condition is being tested and analyzed to better understand these compaction mechanisms and provide a basis from which to evaluate their impact to the safety basis for transportation (Safety Analysis Report for Packaging) and storage (facility Design Safety Analysis) at the Savannah River Site (SRS). A test program has been developed and is being implemented to identify the extent of the compaction as a function of fiberboard moisture and typical transport dynamic loadings. Test conditions will be compared to regulatory requirements for dynamic loading. Characterization of the recovery of short-term compaction following the application of dynamic loading is also being evaluated. Interim results from this test program will be summarized.

  14. Status of the Silicon Photomultiplier Telescope FAMOUS for the Fluorescence Detection of UHECRs

    E-Print Network [OSTI]

    Niggemann, Tim; Brogueira, Pedro; Bueno, Antonio; Eichler, Hans Michael; Ferreira, Miguel; Hebbeker, Thomas; Lauscher, Markus; Mendes, Luís; Middendorf, Lukas; Navas, Sergio; Peters, Christine; Pimenta, Mário; Ruiz, Angel; Schumacher, Johannes; Stephan, Maurice

    2015-01-01T23:59:59.000Z

    An established technique for the measurement of ultra-high-energy-cosmic-rays is the detection of the fluorescence light induced in the atmosphere of the Earth, by means of telescopes equipped with photomultiplier tubes. Silicon photomultipliers (SiPMs) promise an increase in the photon detection efficiency which outperforms conventional photomultiplier tubes. In combination with their compact package, a moderate bias voltage of several ten volt and single photon resolution, the use of SiPMs can improve the energy and spatial resolution of air fluorescence measurements, and lead to a gain in information on the primary particle. Though, drawbacks like a high dark-noise-rate and a strong temperature dependency have to be managed. FAMOUS is a refracting telescope prototype instrumented with 64 SiPMs of which the main optical element is a Fresnel lens of 549.7 mm diameter and 502.1 mm focal length. The sensitive area of the SiPMs is increased by a special light collection system consisting of Winston cones. The t...

  15. Structural Reliability: Assessing the Condition and Reliability of Casing in Compacting Reservoirs

    E-Print Network [OSTI]

    Chantose, Prasongsit

    2012-02-14T23:59:59.000Z

    . Effective stress may exceed rock compressive strength, inducing compaction. Wells in compacting reservoirs risk high failure and deformation rates. This project introduces the concept of structural reliability to quantify casing failure risks in compacting...

  16. Structural Reliability: Assessing the Condition and Reliability of Casing in Compacting Reservoirs 

    E-Print Network [OSTI]

    Chantose, Prasongsit

    2012-02-14T23:59:59.000Z

    Casing has a higher risk of failure in a compacting reservoir than in a typical reservoir. Casing fails when reservoir compaction induces compression and shear stresses onto it. They compact as reservoir pressure depletes during production. High...

  17. Thermal and electrical conduction in the compaction direction of exfoliated graphite

    E-Print Network [OSTI]

    Chung, Deborah D.L.

    Thermal and electrical conduction in the compaction direction of exfoliated graphite in the compaction direction of graphite-flake-based exfoliated graphite have been decoupled. The compact Exfoliated graphite is elongated graphite particles obtained by the exfoliation (typically involving rapid

  18. Manifold corrections on spinning compact binaries

    SciTech Connect (OSTI)

    Zhong Shuangying; Wu Xin [Nanchang University, Nanchang 330031 (China)

    2010-05-15T23:59:59.000Z

    This paper deals mainly with a discussion of three new manifold correction methods and three existing ones, which can numerically preserve or correct all integrals in the conservative post-Newtonian Hamiltonian formulation of spinning compact binaries. Two of them are listed here. One is a new momentum-position scaling scheme for complete consistency of both the total energy and the magnitude of the total angular momentum, and the other is the Nacozy's approach with least-squares correction of the four integrals including the total energy and the total angular momentum vector. The post-Newtonian contributions, the spin effects, and the classification of orbits play an important role in the effectiveness of these six manifold corrections. They are all nearly equivalent to correct the integrals at the level of the machine epsilon for the pure Kepler problem. Once the third-order post-Newtonian contributions are added to the pure orbital part, three of these corrections have only minor effects on controlling the errors of these integrals. When the spin effects are also included, the effectiveness of the Nacozy's approach becomes further weakened, and even gets useless for the chaotic case. In all cases tested, the new momentum-position scaling scheme always shows the optimal performance. It requires a little but not much expensive additional computational cost when the spin effects exist and several time-saving techniques are used. As an interesting case, the efficiency of the correction to chaotic eccentric orbits is generally better than one to quasicircular regular orbits. Besides this, the corrected fast Lyapunov indicators and Lyapunov exponents of chaotic eccentric orbits are large as compared with the uncorrected counterparts. The amplification is a true expression of the original dynamical behavior. With the aid of both the manifold correction added to a certain low-order integration algorithm as a fast and high-precision device and the fast Lyapunov indicators of two nearby trajectories, phase space scans for chaos in the spinning compact binary system are given.

  19. Process for forming coal compacts and product thereof

    DOE Patents [OSTI]

    Gunnink, Brett (Columbia, MO); Kanunar, Jayanth (Arlington, MA); Liang, Zhuoxiong (San Francisco, CA)

    2002-01-01T23:59:59.000Z

    A process for forming durable, mechanically strong compacts from coal particulates without use of a binder is disclosed. The process involves applying a compressive stress to a particulate feed comprising substantially water-saturated coal particles while the feed is heated to a final compaction temperature in excess of about 100.degree. C. The water present in the feed remains substantially in the liquid phase throughout the compact forming process. This is achieved by heating and compressing the particulate feed and cooling the formed compact at a pressure sufficient to prevent water present in the feed from boiling. The compacts produced by the process have a moisture content near their water saturation point. As a result, these compacts absorb little water and retain exceptional mechanical strength when immersed in high pressure water. The process can be used to form large, cylindrically-shaped compacts from coal particles (i.e., "coal logs") so that the coal can be transported in a hydraulic coal log pipeline.

  20. COMPACTION OF FIBERBOARD IN A 9975 SHIPPING PACKAGE

    SciTech Connect (OSTI)

    Stefek, T.; Daugherty, W.; Estochen, E.; Leduc, D.

    2011-05-11T23:59:59.000Z

    Compaction of lower layers in the fiberboard overpack has been observed in 9975 packages that contain elevated moisture. Lab testing has resulted in a better understanding of (1) the relationship between the fiberboard moisture level and compaction of the lower fiberboard assembly, and (2) the behavior of the fiberboard during transport. In laboratory tests, higher moisture content has been shown to correspond to higher total compaction of fiberboard material, greater rate of compaction, and continued compaction over a longer period of time. In addition, laboratory tests have shown that the application of a dynamic load results in higher fiberboard compaction. The test conditions and sample geometric/loading configurations were chosen to simulate the regulatory requirements for 9975 package input dynamic loading. Dynamic testing was conducted over a period of several months to acquire immediate and cumulative changes in geometric data for various moisture levels. Currently, one sample set has undergone a complete dynamic test regimen, while testing of another set is still in-progress. The dynamic input, data acquisition, test effects on sample dynamic parameters, and interim results from this test program will be summarized and compared to regulatory specifications for dynamic loading. This will provide a basis from which to evaluate the impact of moisture and fiberboard compaction on the safety basis for transportation (Safety Analysis Report for Packaging) and storage (facility Documented Safety Analysis) at the Savannah River Site (SRS).

  1. Study and Simulation of Remote Sensing System: COMPACT Airborne Spectral Sensor (COMPASS)

    E-Print Network [OSTI]

    Salvaggio, Carl

    1 Study and Simulation of Remote Sensing System: COMPACT Airborne Spectral Sensor (COMPASS) Paper............................................................................................ 5 COMPACT Airborne Spectral Sensor (COMPASS............................................................................................... 9 (FOUO) COMPASS Megacollect Data

  2. MACHO (MAssive Compact Halo Objects) Data

    DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

    The primary aim of the MACHO Project is to test the hypothesis that a significant fraction of the dark matter in the halo of the Milky Way is made up of objects like brown dwarfs or planets: these objects have come to be known as MACHOs, for MAssive Compact Halo Objects. The signature of these objects is the occasional amplification of the light from extragalactic stars by the gravitational lens effect. The amplification can be large, but events are extremely rare: it is necessary to monitor photometrically several million stars for a period of years in order to obtain a useful detection rate. For this purpose MACHO has a two channel system that employs eight CCDs, mounted on the 50 inch telescope at Mt. Stromlo. The high data rate (several GBytes per night) is accommodated by custom electronics and on-line data reduction. The Project has taken more than 27,000 images with this system since June 1992. Analysis of a subset of these data has yielded databases containing light curves in two colors for 8 million stars in the LMC and 10 million in the bulge of the Milky Way. A search for microlensing has turned up four candidates toward the Large Magellanic Cloud and 45 toward the Galactic Bulge. The web page for data provides links to MACHO Project data portals and various specialized interfaces for viewing or searching the data. (Specialized Interface)

  3. Compact directed percolation with movable partial reflectors

    E-Print Network [OSTI]

    Ronald Dickman; Daniel ben-Avraham

    2002-07-08T23:59:59.000Z

    We study a version of compact directed percolation (CDP) in one dimension in which occupation of a site for the first time requires that a "mine" or antiparticle be eliminated. This process is analogous to the variant of directed percolation with a long-time memory, proposed by Grassberger, Chate and Rousseau [Phys. Rev. E 55, 2488 (1997)] in order to understand spreading at a critical point involving an infinite number of absorbing configurations. The problem is equivalent to that of a pair of random walkers in the presence of movable partial reflectors. The walkers, which are unbiased, start one lattice spacing apart, and annihilate on their first contact. Each time one of the walkers tries to visit a new site, it is reflected (with probability r) back to its previous position, while the reflector is simultaneously pushed one step away from the walker. Iteration of the discrete-time evolution equation for the probability distribution yields the survival probability S(t). We find that S(t) \\sim t^{-delta}, with delta varying continuously between 1/2 and 1.160 as the reflection probability varies between 0 and 1.

  4. The spheromak as a compact fusion reactor

    SciTech Connect (OSTI)

    Hagenson, R.L.; Krakowski, R.A.

    1987-03-01T23:59:59.000Z

    After summarizing the economic and utility-based rationale for compact, higher-power-density fusion reactors, the gun-sustained spheromak concept is explored as one of a number of poloidal-field-dominated confinement configurations that might improve the prospects for economically attractive and operationally simplified fusion power plants. Using a comprehensive physics/engineering/costing model for the spheromak, guided by realistic engineering constraints and physics extrapolation, a range of cost-optimized reactor design points is presented, and the sensitivity of cost to key physics, engineering, and operational variables is reported. The results presented herein provide the basis for conceptual engineering designs of key fusion-power-core (FPC) subsystems and more detailed plasma modeling of this promising, high mass-power-density concept, which stresses single-piece FPC maintenance, steady-state current drive through electrostatic magnetic helicity injection, a simplified co-axial electrode-divertor, and efficient resistive-coal equilibrium-field coils. The optimal FPC size and the cost estimates project a system that competes aggressively with the best offered by alternative energy sources while simplifying considerably the complexity that has generally been associated with most approaches to magnetic fusion energy.

  5. GUTs on Compact Type IIB Orientifolds

    SciTech Connect (OSTI)

    Blumenhagen, Ralph; /Munich, Max Planck Inst.; Braun, Volker; /Dublin Inst.; Grimm, Thomas W.; /Bonn U.; Weigand, Timo; /SLAC

    2008-12-01T23:59:59.000Z

    We systematically analyze globally consistent SU(5) GUT models on intersecting D7-branes in genuine Calabi-Yau orientifolds with O3- and O7-planes. Beyond the well-known tadpole and K-theory cancellation conditions there exist a number of additional subtle but quite restrictive constraints. For the realization of SU(5) GUTs with gauge symmetry breaking via U(1)Y flux we present two classes of suitable Calabi-Yau manifolds defined via del Pezzo transitions of the elliptically fibred hypersurface P{sub 1,1,1,6,9}[18] and of the Quintic P{sub 1,1,1,1,1}[5], respectively. To define an orientifold projection we classify all involutions on del Pezzo surfaces. We work out the model building prospects of these geometries and present five globally consistent string GUT models in detail, including a 3-generation SU(5) model with no exotics whatsoever. We also realize other phenomenological features such as the 10 10 5{sub H} Yukawa coupling and comment on the possibility of moduli stabilization, where we find an entire new set of so-called swiss-cheese type Calabi-Yau manifolds. It is expected that both the general constrained structure and the concrete models lift to F-theory vacua on compact Calabi-Yau fourfolds.

  6. Polymer quantum effects on compact stars models

    E-Print Network [OSTI]

    Guillermo Chacon-Acosta; Hector Hernandez-Hernandez

    2014-08-05T23:59:59.000Z

    In this work we study a completely degenerated fermion gas at zero temperature within a semiclassical approximation for the Hamiltonian arising in polymer quantum mechanics. Polymer quantum systems are quantum mechanical models quantized in a similar way as in loop quantum gravity that allow the study of the discreteness of space and other features of the loop quantization in a simplified way. We obtain the polymer modified thermodynamical properties noticing that the corresponding Fermi energy is exactly the same as if one directly polymerizes the momentum $p_F$. We also obtain the corresponding expansion of thermodynamical variables for small values of the polymer length scale $\\lambda$. With this results we study a simple model of a compact object where the gravitational collapse is supported by electron degeneracy pressure. We find polymer corrections to the mass of the star. When compared with typical measurements of the mass of white dwarfs we obtain a bound on the polymer length of $\\lambda^2\\lesssim 10^{-26}m^2$.

  7. Color superconducting quark matter in compact stars

    E-Print Network [OSTI]

    D. B. Blaschke; T. Klahn; F. Sandin

    2007-12-02T23:59:59.000Z

    Recent indications for high neutron star masses (M \\sim 2 M_sun) and large radii (R > 12 km) could rule out soft equations of state and have provoked a debate whether the occurence of quark matter in compact stars can be excluded as well. We show that modern quantum field theoretical approaches to quark matter including color superconductivity and a vector meanfield allow a microscopic description of hybrid stars which fulfill the new, strong constraints. For these objects color superconductivity turns out to be an essential ingredient for a successful description of the cooling phenomenology in accordance with recently developed tests. We discuss the energy release in the neutrino untrapping transition as a new aspect of the problem that hybrid stars masquerade themselves as neutron stars. Quark matter searches in future generations of low-temperature/high-density nucleus-nucleus collision experiments such as low-energy RHIC and CBM @ FAIR might face the same problem of an almost crossover behavior of the deconfinement transition. Therefore, diagnostic tools shall be derived from effects of color superconductivity.

  8. Compact noninvasive electron bunch-length monitor

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Roberts, B.; Mammei, R. R.; Poelker, M.; McCarter, J. L.

    2012-12-01T23:59:59.000Z

    A compact rf cavity was constructed that simultaneously resonates at many harmonic modes when excited by a repetitive bunched electron beam passing through its bore. The excitation of these modes provides a Fourier description of the temporal characteristics of the bunch train. The cavity was used to noninvasively characterize electron bunches produced from thin and thick GaAs photocathodes inside a DC high voltage photogun illuminated with 37 ps (full width half maximum, FWHM) laser pulses at repetition rates near 1500 MHz, at average beam current from 5 to 500????A , and at beam energy from 75 to 195 keV. The cavity bunch-length monitor could detect electron bunches as short as 57 ps (FWHM) when connected directly to a sampling oscilloscope, and could clearly distinguish bunches with varying degrees of space-charge induced growth and with different tail signatures. Efforts are under way to detect shorter bunches by designing cavities with increased bandwidth. This demonstration lends credibility to the idea that these cavities could also be used for other applications, including bunching and shaping, when driven with external rf.

  9. Iron-carbon compacts and process for making them

    DOE Patents [OSTI]

    Sheinberg, Haskell (Santa Fe, NM)

    2000-01-01T23:59:59.000Z

    The present invention includes iron-carbon compacts and a process for making them. The process includes preparing a slurry comprising iron powder, furfuryl alcohol, and a polymerization catalyst for initiating the polymerization of the furfuryl alcohol into a resin, and heating the slurry to convert the alcohol into the resin. The resulting mixture is pressed into a green body and heated to form the iron-carbon compact. The compact can be used as, or machined into, a magnetic flux concentrator for an induction heating apparatus.

  10. Preparation of bulk superhard B-C-N nanocomposite compact

    DOE Patents [OSTI]

    Zhao, Yusheng (Los Alamos, NM); He, Duanwei (Sichuan, CN)

    2011-05-10T23:59:59.000Z

    Bulk, superhard, B--C--N nanocomposite compacts were prepared by ball milling a mixture of graphite and hexagonal boron nitride, encapsulating the ball-milled mixture at a pressure in a range of from about 15 GPa to about 25 GPa, and sintering the pressurized encapsulated ball-milled mixture at a temperature in a range of from about 1800-2500 K. The product bulk, superhard, nanocomposite compacts were well sintered compacts with nanocrystalline grains of at least one high-pressure phase of B--C--N surrounded by amorphous diamond-like carbon grain boundaries. The bulk compacts had a measured Vicker's hardness in a range of from about 41 GPa to about 68 GPa.

  11. Compact Data Structures with Fast Queries Daniel K. Blandford

    E-Print Network [OSTI]

    .5 Decoding Multiple Gamma Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 2.6 Rank of Computer Science Carnegie Mellon University Pittsburgh, PA 15213 Thesis Committee: Guy E. Blelloch, chair fast queries (and updates) to the data. This thesis describes compact representations of several types

  12. aeropropulsion compact lightweight: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    24 25 Next Page Last Page Topic Index 1 Design of a compact, lightweight, and low-cost solar concentrator MIT - DSpace Summary: The objective of this mechanical design project was...

  13. Compact hot-nozzle fourier-transform microwave spectormeter

    E-Print Network [OSTI]

    Harmony, Marlin D.; Ratzlaff, Kenneth L.; Angst, D. M.; Beren, K. A.

    1995-11-01T23:59:59.000Z

    A newly constructed pulsed nozzle, Fourier-transform microwave spectrometer utilizes a Fabry-Perot cavity consisting of spherical resonators having diameters of only 10 cm. Tests of this very compact-cavity system show ...

  14. Development, Test and Demonstration of a Cost-Effective, Compact...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    and Peer Evaluation ape012taylor2011o.pdf More Documents & Publications Development, Test and Demonstration of a Cost-Effective, Compact, Light-Weight, and Scalable High...

  15. A Plastic-Core Compact Heat Exchanger for Energy Conservation

    E-Print Network [OSTI]

    Lazaridis, A.; Rafailidis, E.

    This paper describes a compact, single-pass, cross-flow type, gas-to-gas heat exchanger with a polyolefin (polyethylene or polypropylene) core whose seams are welded through a proprietary process. It is constructed of several extruded polyolefin...

  16. Classification of Certain Compact Riemannian Manifolds with Harmonic Curvature a...

    E-Print Network [OSTI]

    Derdzinski, Andrzej

    Classification of Certain Compact Riemannian Manifolds with Harmonic Curvature a... Derdzinski and University Library provides access to digitized documents strictly for noncommercial educational, research) requires prior written permission from the Goettingen State- and University Library. Each copy of any part

  17. A Plastic-Core Compact Heat Exchanger for Energy Conservation 

    E-Print Network [OSTI]

    Lazaridis, A.; Rafailidis, E.

    1995-01-01T23:59:59.000Z

    This paper describes a compact, single-pass, cross-flow type, gas-to-gas heat exchanger with a polyolefin (polyethylene or polypropylene) core whose seams are welded through a proprietary process. It is constructed of several extruded polyolefin...

  18. Folded Compact Range Development and Coherent Change Detection Measurement Project

    SciTech Connect (OSTI)

    Sorensen, K.W.

    1995-03-01T23:59:59.000Z

    A novel, folded compact range configuration has been developed at the Sandia National Laboratories compact range antenna and radar cross section measurement facility, operated by the Radar/Antenna Department 2343, as a means of performing indoor, environmentally-controlled, far-field simulations of synthetic aperture radar (SAR) coherent change detection (CCD) measurements. This report describes the development of the folded compact range configuration, as well as the initial set of coherent change detection measurements made with the system. These measurements have been highly successful, and have demonstrated the viability of the folded compact range concept in simulating SAR CCD measurements. It is felt that follow-on measurements have the potential of contributing significantly to the body of knowledge available to the scientific community involved in CCD image generation and processing, and that this tool will be a significant aid in the research and development of change detection methodologies.

  19. CTI in NSTX, Proposal for Compact Toroid Injection in NSTX

    SciTech Connect (OSTI)

    R. Raman

    2008-11-04T23:59:59.000Z

    This is the final Report summarizing the activities of the proposal to invetigate the potential of deep fueling a spherical torus or tokamak using high velocity injection of compact toroids.

  20. Compact, Isolated High-Velocity Clouds

    E-Print Network [OSTI]

    W. B. Burton; R. Braun; V. de Heij

    2002-06-20T23:59:59.000Z

    We consider here the class of compact, isolated, high-velocity HI clouds, CHVCs, which are sharply bounded in angular extent down to a limiting column density of 1.5x10^18 cm^-2. We describe our automated search algorithm and it's application to the LDS north of dec= -28 deg. and the HIPASS data south of dec=0, resulting in an all--sky catalog numbering 246 CHVCs. We argue that these objects are more likely to represent a single phenomenon in a similar evolutionary state than would a sample which included any of the major HVC complexes. Five principal observables are defined for the CHVC population: (1) the spatial deployment of the objects on the sky, (2) the kinematic distribution, (3) the number distribution of observed HI column densities, (4) the number distribution of angular sizes, and (5) the number distribution of line widths. We show that the spatial and kinematic deployments of the ensemble of CHVCs contain various clues regarding their characteristic distance. These clues are not compatible with a location of the ensemble within the Galaxy proper. The deployments resemble in several regards those of the Local Group galaxies. We describe a model testing the hypothesis that the CHVCs are a Local Group population. The agreement of the model with the data is judged by extracting the observables from simulations, in a manner consistent with the sensitivities of the observations and explicitly taking account of Galactic obscuration. We show that models in which the CHVCs are the HI counterparts of dark-matter halos evolving in the Local Group potential provide a good match to the observables, if account is taken of tidal and ram--pressure disruption, the consequences of obscuration due to Galactic HI and of differing sensitivities and selection effects pertaining to the surveys.

  1. Engineering properties of miniature cement - fly ash compacts prepared by high pressure compaction 

    E-Print Network [OSTI]

    Bormann, Jeffrey Ray

    1985-01-01T23:59:59.000Z

    ENGINEERING PROPERTIES OF MINIATURE CEMENT - FLY ASH COMPACTS PREPARED BY HIGH PRESSURE COMPACTION E NGIRPR OT SFMMAFU AEU C-ALEYY HDOBPvvIi va vGI ge(iD(vI oannItI au NId(R E)L xrP1IeRPvT 9(evP(n uDnuPnnBIrv au vGI eI0DPeIBIrvR uae vGI i...?H?? NId(R E)L xrP1IeRPvT oG(PeB(r au Ei1PRaeT oaBBPvvII? ?e? ??C? ?IiOIvvIe oDeeIrv 9e(8vP8IR (ri vGIaeT 8aruaeB va vGI 8ar8I9v vG(v uae R9I8P(nP?Ii DRIR ( 9aevn(ri 8IBIrv 8ar8eIvI B(vIeP(n ?PvG RveIrtvG (99ea(8GPrt ?????? 9RP B(T OI 9eaiD8Ii OT eIiD8...

  2. Ship response using a compact wave spectrum model

    E-Print Network [OSTI]

    Linn, Larry Donald

    1985-01-01T23:59:59.000Z

    statistical technique, known as principal component analysis, is used to compact large data bases of theoretical and real spectral information. Statistical properties of the various data bases are examined in their original and compacted forms. Sensitivity.... The available spectrum models fall into two basic categories. Formulas which use the first, or "classic, " approach use wind speed as the independent variable to define the spectrum. The Pierson-Noskowitz Spectrum is an example of this type...

  3. Solid state laser media driven by remote nuclear powered fluorescence

    DOE Patents [OSTI]

    Prelas, Mark A. (Columbia, MO)

    1992-01-01T23:59:59.000Z

    An apparatus is provided for driving a solid state laser by a nuclear powered fluorescence source which is located remote from the fluorescence source. A nuclear reaction produced in a reaction chamber generates fluorescence or photons. The photons are collected from the chamber into a waveguide, such as a fiber optic waveguide. The waveguide transports the photons to the remote laser for exciting the laser.

  4. Absolute Calibration of the Auger Fluorescence Detectors

    E-Print Network [OSTI]

    P. Bauleo; J. Brack; L. Garrard; J. Harton; R. Knapik; R. Meyhandan; A. C. Rovero; A. Tamashiro; D. Warner; for the Auger Collaboration

    2005-07-14T23:59:59.000Z

    Absolute calibration of the Pierre Auger Observatory fluorescence detectors uses a light source at the telescope aperture. The technique accounts for the ombined effects of all detector components in a single measurement. The calibrated 2.5 m diameter light source fills the aperture, providing uniform illumination to each pixel. The known flux from the light source and the response of the acquisition system give the required calibration for each pixel. In the lab, light source uniformity is studied using CCD images and the intensity is measured relative to NIST-calibrated photodiodes. Overall uncertainties are presently 12%, and are dominated by systematics.

  5. Fluorescent Lamp Ballasts | Department of Energy

    Energy Savers [EERE]

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page onYou are now leaving Energy.gov You are now leaving Energy.gov You are being directed offOCHCO2: FinalOffers3.pdf0-45.pdf Flash2010-45.pdfFlash2011-43and Statement ofStrikeFluorescent

  6. Fluorescent Optical Position Sensor - Energy Innovation Portal

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645U.S. DOEThe Bonneville Power AdministrationField8,Dist.New MexicoFinancingProofWorking OutsideFluorescent

  7. Fluorescent Pigments for High-Performance Cool Roofing and Facades...

    Energy Savers [EERE]

    dark-colored pigments for cool metal roof and faade coatings that incorporate near-infrared fluorescence and reflectance to improve energy performance. Image: PPG Industries 2...

  8. Satellite-detected fluorescence reveals global physiology of ocean phytoplankton

    E-Print Network [OSTI]

    2009-01-01T23:59:59.000Z

    2000. Jassby, A. D. and Platt, T. : Mathematical formulationTopliss, B. J. and Platt, T. : Passive fluorescence andrates (Topliss and Platt, 1986; Kiefer et al. , 1989) and

  9. atomic fluorescence spectrometry: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    S. Chapman 2010-12-08 9 Quantification of trace metals in deciduous tooth enamel using energy dispersive X-ray fluorescence spectrometry. Open Access Theses and Dissertations...

  10. Fluorescent Multiblock ?-Conjugated Polymer Nanoparticles for In Vivo Tumor Targeting

    E-Print Network [OSTI]

    Ahmed, Eilaf

    Highly fluorescent multiblock conjugated polymer nanoparticles with folic acid surface ligands are highly effective for bioimaging and in vivo tumor targeting. The targeted nanoparticles were preferentially localized in ...

  11. Time-resolved fluorescence decay measurements for flowing particles

    DOE Patents [OSTI]

    Deka, C.; Steinkamp, J.A.

    1999-06-01T23:59:59.000Z

    Time-resolved fluorescence decay measurements are disclosed for flowing particles. An apparatus and method for the measurement and analysis of fluorescence for individual cells and particles in flow are described, wherein the rapid measurement capabilities of flow cytometry and the robust measurement and analysis procedures of time-domain fluorescence lifetime spectroscopy are combined. A pulse-modulated CW laser is employed for excitation of the particles. The characteristics and the repetition rate of the excitation pulses can be readily adjusted to accommodate for fluorescence decays having a wide range of lifetimes. 12 figs.

  12. aequorea green fluorescent: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    plants. Jim Haseloff Biology and Medicine Websites Summary: light, and an accessory green fluorescent protein (GFP), which accepts energy from aequorin and reImaging green...

  13. Modeling of highly loaded fluorescent lamps

    SciTech Connect (OSTI)

    Lister, G.G.; Lawler, J.E.; Curry, J.J.

    1999-07-01T23:59:59.000Z

    Numerical modeling of the positive column of fluorescent lamps under conditions of high current density are of current interest, particularly in view of recent developments in electrodeless lamps. Current models tend to overestimate radiation output, and consequently the maintenance electric field in these discharges. Under highly loaded conditions, mercury-rare gas fluorescent lamps exhibit strong mercury depletion on axis (cataphoresis), and an understanding of resonance radiation transport under these conditions is therefore vital to the development of models with a predictive capability. The authors have explored the effect of radial cataphoresis on resonance radiation trapping for situations in which the radiation transport is dominated by foreign gas broadening, Doppler broadening, or resonance collisional broadening of the spectral line. Several different production rates per unit volume of resonance (excited) atoms have also been studied. It is advantageous in many cases to parameterize the trapped decay rate in terms of the total number of ground state atoms in the positive column independent of their radial distribution. The results of this work have been included in a numerical model of the positive column and the predicted influence on discharge parameters will be presented for cases of interest to highly loaded lamps.

  14. Max Tech and Beyond: Fluorescent Lamps

    SciTech Connect (OSTI)

    Scholand, Michael

    2012-04-01T23:59:59.000Z

    Fluorescent lamps are the most widely used artificial light source today, responsible for approximately 70% of the lumens delivered to our living spaces globally. The technology was originally commercialized in the 1930's, and manufacturers have been steadily improving the efficacy of these lamps over the years through modifications to the phosphors, cathodes, fill-gas, operating frequency, tube diameter and other design attributes. The most efficient commercially available fluorescent lamp is the 25 Watt T5 lamp. This lamp operates at 114-116 lumens per watt while also providing good color rendering and more than 20,000 hours of operating life. Industry experts interviewed indicated that while this lamp is the most efficient in the market today, there is still a further 10 to 14% of potential improvements that may be introduced to the market over the next 2 to 5 years. These improvements include further developments in phosphors, fill-gas, cathode coatings and ultraviolet (UV) reflective glass coatings. The commercialization of these technology improvements will combine to bring about efficacy improvements that will push the technology up to a maximum 125 to 130 lumens per watt. One critical issue raised by researchers that may present a barrier to the realization of these improvements is the fact that technology investment in fluorescent lamps is being reduced in order to prioritize research into light emitting diodes (LEDs) and ceramic metal halide high intensity discharge (HID) lamps. Thus, it is uncertain whether these potential efficacy improvements will be developed, patented and commercialized. The emphasis for premium efficacy will continue to focus on T5 lamps, which are expected to continue to be marketed along with the T8 lamp. Industry experts highlighted the fact that an advantage of the T5 lamp is the fact that it is 40% smaller and yet provides an equivalent lumen output to that of a T8 or T12 lamp. Due to its smaller form factor, the T5 lamp contains less material (i.e., glass, fill gas and phosphor), and has a higher luminance, enabling fixtures to take advantage of the smaller lamp size to improve the optics and provide more efficient overall system illuminance. In addition to offering the market a high-quality efficacious light source, another strong value proposition of fluorescent lighting is its long operating life. In today's market, one manufacturer is offering fluorescent lamps that have a rated life of 79,000 hours - which represents 18 years of service at 12 hours per day, 365 days per year. These lamps, operated using a long-life ballast specified by the manufacturer, take advantage of improvements in cathode coatings, fill gas chemistry and pressure to extend service life by a factor of four over conventional fluorescent lamps. It should be noted that this service life is also longer (approximately twice as long) as today's high-quality LED products. The fluorescent market is currently focused on the T5 and T8 lamp diameters, and it is not expected that other diameters would be introduced. Although T8 is a more optimal diameter from an efficacy perspective, the premium efficiency and optimization effort has been focused on T5 lamps because they are 40% smaller than T8, and are designed to operate at a higher temperature using high-frequency electronic ballasts. The T5 lamp offers savings in terms of materials, packaging and shipping, as well as smaller fixtures with improved optical performance. Manufacturers are actively researching improvements in four critical areas that are expected to yield additional efficacy improvements of approximately 10 to 14 percent over the next five years, ultimately achieving approximately 130 lumens per watt by 2015. The active areas of research where these improvements are anticipated include: (1) Improved phosphors which continue to be developed and patented, enabling higher efficacies as well as better color rendering and lumen maintenance; (2) Enhanced fill gas - adjusting proportions of argon, krypton, neon and xenon to optimize performance, while also m

  15. Development and Application of Fluorescent SDF-1 Derivatives Ryo Masuda,

    E-Print Network [OSTI]

    Takada, Shoji

    #12;1 Development and Application of Fluorescent SDF-1 Derivatives Ryo Masuda, Shinya Oishi of Medicine, 2-1 Seiryocho, Aoba-ku, Sendai 980-8575, Japan. #12;2 Abstract Background: SDF-1/CXCR4 signaling, structure-activity relationship analyses of fluorescent SDF-1 derivatives were carried out. Results: Several

  16. Improved ``Optical Highlighter'' Probes Derived from Discosoma Red Fluorescent Protein

    E-Print Network [OSTI]

    Marchant, Jonathan

    , Minneapolis, Minnesota ABSTRACT The tetrameric red fluorescent protein, DsRed, undergoes a rapid red to green-emitting species of DsRed and an enhancement of emission from the ``immature'' green species, likely caused by dequenching of fluorescence resonance energy transfer occurring within the protein tetramer. Here, we have

  17. Gregorio Weber International Prize in Biological Fluorescence 2008

    E-Print Network [OSTI]

    Weber, David J.

    Gregorio Weber International Prize in Biological Fluorescence 2008 The Gregorio Weber International Prize in Biological Fluorescence (Weber Prize) is awarded for research related to a doctoral (or finalists. Weber Prizes were awarded in 2002 and 2005. The third Weber Prize will be awarded in 2008

  18. Comparison of Segmentation Algorithms For Fluorescence Microscopy Images of Cells

    E-Print Network [OSTI]

    Bernal, Javier

    - mentation techniques are less accurate than k-means clustering with multiple clusters. Segmentation accuracy fluorescence microscopy; k-means cluster; image segmentation; cell edge; bivariate simi- larity index NUMEROUSComparison of Segmentation Algorithms For Fluorescence Microscopy Images of Cells Alden A. Dima,1

  19. Fluorescence correlation spectroscopy at high concentrations using gold bowtie nanoantennas

    E-Print Network [OSTI]

    Fan, Shanhui

    Fluorescence correlation spectroscopy at high concentrations using gold bowtie nanoantennas Anika A to extremely low concentrations. Plasmonic gold bowtie nanoantennas enhance a single molecule's fluorescence relative to a large background of unenhanced molecules, and here we show that bowties can extend FCS

  20. Teal fluorescent proteins: Characterization of a reversibly photoswitchable variant

    E-Print Network [OSTI]

    Campbell, Robert E.

    libraries of variants. mTFP1 has proven to be a particularly useful new member of the FP `toolbox green fluorescent protein (GFP) in 1961 when he was isolating aequorin, a calcium improved variants of GFP, including the variant known as enhanced green fluorescent protein (EGFP), were

  1. Application of Quantitative Fluorescence and Absorption-Edge

    E-Print Network [OSTI]

    Sparks, Donald L.

    Application of Quantitative Fluorescence and Absorption-Edge Computed Microtomography to Image, Chicago, Illinois 60637 This paper shows that synchrotron-based fluorescence and absorption-edge computed, which had a well-correlated metal coating. Absorption-edge CMT showed the three-dimensional distribution

  2. Compact Reversed-Field Pinch Reactors (CRFPR): preliminary engineering considerations

    SciTech Connect (OSTI)

    Hagenson, R.L.; Krakowski, R.A.; Bathke, C.G.; Miller, R.L.; Embrechts, M.J.; Schnurr, N.M.; Battat, M.E.; LaBauve, R.J.; Davidson, J.W.

    1984-08-01T23:59:59.000Z

    The unique confinement physics of the Reversed-Field Pinch (RFP) projects to a compact, high-power-density fusion reactor that promises a significant reduction in the cost of electricity. The compact reactor also promises a factor-of-two reduction in the fraction of total cost devoted to the reactor plant equipment (i.e., fusion power core (FPC) plus support systems). In addition to operational and developmental benefits, these physically smaller systems can operate economically over a range of total power output. After giving an extended background and rationale for the compact fusion approaches, key FPC subsystems for the Compact RFP Reactor (CRFPR) are developed, designed, and integrated for a minimum-cost, 1000-MWe(net) system. Both the problems and promise of the compact, high-power-density fusion reactor are quantitatively evaluated on the basis of this conceptual design. The material presented in this report both forms a framework for a broader, more expanded conceptual design as well as suggests directions and emphases for related research and development.

  3. The DPOSS II compact group survey: first spectroscopically confirmed candidates

    E-Print Network [OSTI]

    Pompei, E; Iovino, A

    2006-01-01T23:59:59.000Z

    This paper presents the results of a pilot redshift survey of 18 candidate compact groups from the distant DPOSS survey that extends the available surveys of compact groups of galaxies to z ~0.2 in redshift, mainly Hickson Compact Groups and Southern Compact Groups. The goal of our survey was to confirm group membership via redshift information and to measure the characteristic parameters of a representative, albeit small, sample of DPOSS survey groups. Of the 18 candidates observed, seven are found to be indeed isolated compact groups, i.e. groups with 3 or more concordant members and with no neighbouring known cluster, while 7 are chance projection configurations on the sky. Three remaining candidates, despite having 3 or more concordant member galaxies, are located in the neighbourhood of known clusters, while another candidate turned out to be a dense sub-condensation within Abell 0952. The median redshift of our 7 confirmed groups is z ~0.12, to be compared with a median redshift of 0.03 for the local sa...

  4. SIMULTANEOUS MEASUREMENT OF CIRCULAR DICHROISM AND FLUORESCENCE POLARIZATION ANISOTROPY.

    SciTech Connect (OSTI)

    SUTHERLAND,J.C.

    2002-01-19T23:59:59.000Z

    Circular dichroism and fluorescence polarization anisotropy are important tools for characterizing biomolecular systems. Both are used extensively in kinetic experiments involving stopped- or continuous flow systems as well as titrations and steady-state spectroscopy. This paper presents the theory for determining circular dichroism and fluorescence polarization anisotropy simultaneously, thus insuring the two parameters are recorded under exactly the same conditions and at exactly the same time in kinetic experiments. The approach to measuring circular dichroism is that used in almost all conventional dichrographs. Two arrangements for measuring fluorescence polarization anisotropy are described. One uses a single fluorescence detector and signal processing with a lock-in amplifier that is similar to the measurement of circular dichroism. The second approach uses classic ''T'' format detection optics, and thus can be used with conventional photon-counting detection electronics. Simple extensions permit the simultaneous measurement of the absorption and excitation intensity corrected fluorescence intensity.

  5. HIgh Rate X-ray Fluorescence Detector

    SciTech Connect (OSTI)

    Grudberg, Peter Matthew [XIA LLC

    2013-04-30T23:59:59.000Z

    The purpose of this project was to develop a compact, modular multi-channel x-ray detector with integrated electronics. This detector, based upon emerging silicon drift detector (SDD) technology, will be capable of high data rate operation superior to the current state of the art offered by high purity germanium (HPGe) detectors, without the need for liquid nitrogen. In addition, by integrating the processing electronics inside the detector housing, the detector performance will be much less affected by the typically noisy electrical environment of a synchrotron hutch, and will also be much more compact than current systems, which can include a detector involving a large LN2 dewar and multiple racks of electronics. The combined detector/processor system is designed to match or exceed the performance and features of currently available detector systems, at a lower cost and with more ease of use due to the small size of the detector. In addition, the detector system is designed to be modular, so a small system might just have one detector module, while a larger system can have many â?? you can start with one detector module, and add more as needs grow and budget allows. The modular nature also serves to simplify repair. In large part, we were successful in achieving our goals. We did develop a very high performance, large area multi-channel SDD detector, packaged with all associated electronics, which is easy to use and requires minimal external support (a simple power supply module and a closed-loop water cooling system). However, we did fall short of some of our stated goals. We had intended to base the detector on modular, large-area detectors from Ketek GmbH in Munich, Germany; however, these were not available in a suitable time frame for this project, so we worked instead with pnDetector GmbH (also located in Munich). They were able to provide a front-end detector module with six 100 m^2 SDD detectors (two monolithic arrays of three elements each) along with associated preamplifiers; these detectors surpassed the performance we expected to get from the Ketek detectors, however they are housed in a sealed module, which does not offer the ease of repair and expandability weâ??d hoped to achieve with the Ketek SDDâ??s. Our packaging efforts were quite successful, as we came up with a very compact way to mount the detector and to house the associated electronics, as well as a very effective way to reliably take out the heat (from the electronics as well as the detectorâ??s Peltier coolers) without risk of condensation and without external airflow or vibration, which could create problems for the target applications. While we were able to design compact processing electronics that fit into the detector assembly, they are still at the prototype stage, and would require a significant redesign to achieve product status. We have not yet tested this detector at a synchrotron facility; we do still plan on working with some close contacts at the nearby Stanford Synchrotron Radiation Laboratory (SSRL) to get some testing with the beam (using existing commercial electronics for readout, as the integrated processor is not ready for use).

  6. Radioiodine detector based on laser induced fluorescence

    DOE Patents [OSTI]

    McDonald, Jimmie R. (Upper Marlboro, MD); Baronavski, Andrew P. (Alexandria, VA)

    1980-01-01T23:59:59.000Z

    The invention involves the measurement of the concentration of the radioisotope .sup.129 I.sub.2 in the presence of a gas. The invention uses a laser to excite a sample of the .sup.129 I.sub.2 in a sample gas chamber and a reference sample of a known concentration of .sup.129 I.sub.2 in a reference gas chamber. The .sup.129 I.sub.2 in the sample and reference gas chamber each gives off fluorescence emissions which are received by photomultipliers which provide signals to a detector. The detector uses a ratioing technique to determine the concentration of .sup.129 I.sub.2 in the sample gas chamber.

  7. Fluorescence in nonlocal dissipative periodic structures

    E-Print Network [OSTI]

    Francesco Intravaia; Kurt Busch

    2015-02-24T23:59:59.000Z

    We present an approach for the description of fluorescence from optically active material embedded in layered periodic structures. Based on an exact electromagnetic Green's tensor analysis, we determine the radiative properties of emitters such as the local photonic density of states, Lamb shifts, line widths etc. for a finite or infinite sequence of thin alternating plasmonic and dielectric layers. In the effective medium limit, these systems may exhibit hyperbolic dispersion relations so that the large wave-vector characteristics of all constituents and processes become relevant. These include the finite thickness of the layers, the nonlocal properties of the constituent metals, and local-field corrections associated with an emitter's dielectric environment. In particular, we show that the corresponding effects are non-additive and lead to considerable modifications of an emitter's luminescence properties.

  8. Generating expansion model incorporating compact DC power flow equations

    SciTech Connect (OSTI)

    Nderitu, D.G.; Sparrow, F.T.; Yu, Z. [Purdue Inst. for Interdisciplinary Engineering Studies, West Lafayette, IN (United States)

    1998-12-31T23:59:59.000Z

    This paper presents a compact method of incorporating the spatial dimension into the generation expansion problem. Compact DC power flow equations are used to provide real-power flow coordination equations. Using these equations the marginal contribution of a generator to th total system loss is formulated as a function of that generator`s output. Incorporating these flow equations directly into the MIP formulation of the generator expansion problem results in a model that captures a generator`s true net marginal cost, one that includes both the cost of generation and the cost of transport. This method contrasts with other methods that iterate between a generator expansion model and an optimal power flow model. The proposed model is very compact and has very good convergence performance. A case study with data from Kenya is used to provide a practical application to the model.

  9. Anisotropic Compact Stars in $f(T)$ Gravity

    E-Print Network [OSTI]

    Abbas, G; Zubair, M

    2015-01-01T23:59:59.000Z

    This paper deals with the theoretical modeling of anisotropic compact stars in the framework of $f(T)$ theory of gravity, where $T$ is torsion scalar. To this end, we have used the exact solutions of Krori and Barua metric to a static spherically symmetric metric. The unknown constants involved in the Krori and Barua metric have been specified by using the masses and radii of compact stars 4$U$1820-30, Her X-1, SAX J 1808-3658. The physical properties of these stars have been analyzed in the framework of $f(T)$ theory. In this setting, we have checked the anisotropic behavior, regularity conditions, stability and surface redshift of the compact stars.

  10. Anisotropic Compact Stars in $f(G)$ Gravity

    E-Print Network [OSTI]

    G. Abbas; D. Momeni; M. Aamir Ali; R. Myrzakulov; S. Qaisar

    2014-12-26T23:59:59.000Z

    This paper is devoted to study the possibility of forming anisotropic compact stars in"modified Gauss-Bonnet, namely called as $f(G)$ theory of gravity which is one of the strong candidates, responsible for the accelerated expansion of the universe. For this purpose, we have used analytical solution of Krori and Barua metric to the Einstein field equations with anisotropic form of matter and power law model of $f(G)$ gravity. To determine the unknown constants in Krori and Barua metric, we have used the masses and radii of compact stars, 4$U$1820-30, Her X-1, SAX J 1808-3658. The physical behavior of these stars have been analyzed with the observational data. In this setting, we have checked all the regularity conditions and stability the compact stars 4$U$1820-30, Her X-1, SAX J 1808-3658.

  11. Anisotropic Compact Stars in $f(R)$ Gravity

    E-Print Network [OSTI]

    M. Zubair; G. Abbas

    2015-02-06T23:59:59.000Z

    In this paper we have investigated the possibility of forming of anisotropic compact stars in $f(R)$ gravity, one of the competent candidates of dark energy. To this end, we have applied the analytical solution of Krori and Barua metric to a static spherically symmetric spacetime in $f(R)$ gravity. The unknown constants in Krori and Barua metric have been determined by using masses and radii of class of compact stars like 4$U$1820-30, Her X-1, SAX J 1808-3658. The properties of these stars have been analyzes in detail. Furthermore, we have checked the regularity conditions, energy conditions, anisotropic behavior, stability and surface redshift of the compact stars 4$U$1820-30, Her X-1, SAX J 1808-3658.

  12. Anisotropic Compact Stars in $f(T)$ Gravity

    E-Print Network [OSTI]

    G. Abbas; Afshan Kanwal; M. Zubair

    2015-01-22T23:59:59.000Z

    This paper deals with the theoretical modeling of anisotropic compact stars in the framework of $f(T)$ theory of gravity, where $T$ is torsion scalar. To this end, we have used the exact solutions of Krori and Barua metric to a static spherically symmetric metric. The unknown constants involved in the Krori and Barua metric have been specified by using the masses and radii of compact stars 4$U$1820-30, Her X-1, SAX J 1808-3658. The physical properties of these stars have been analyzed in the framework of $f(T)$ theory. In this setting, we have checked the anisotropic behavior, regularity conditions, stability and surface redshift of the compact stars.

  13. Anisotropic Compact Stars in $f(G)$ Gravity

    E-Print Network [OSTI]

    Abbas, G; Ali, M Aamir; Myrzakulov, R; Qaisar, S

    2015-01-01T23:59:59.000Z

    This paper is devoted to study the possibility of forming anisotropic compact stars in"modified Gauss-Bonnet, namely called as $f(G)$ theory of gravity which is one of the strong candidates, responsible for the accelerated expansion of the universe. For this purpose, we have used analytical solution of Krori and Barua metric to the Einstein field equations with anisotropic form of matter and power law model of $f(G)$ gravity. To determine the unknown constants in Krori and Barua metric, we have used the masses and radii of compact stars, 4$U$1820-30, Her X-1, SAX J 1808-3658. The physical behavior of these stars have been analyzed with the observational data. In this setting, we have checked all the regularity conditions and stability the compact stars 4$U$1820-30, Her X-1, SAX J 1808-3658.

  14. X-Ray Fluorescence (XRF) Analysis of Obsidian Artifacts from Shoofly Ruin, Central Arizona

    E-Print Network [OSTI]

    Shackley, M. Steven

    1986-01-01T23:59:59.000Z

    X-RAY FLUORESCENCE (XRF) ANALYSIS OF OBSIDIAN ARTIFACTS FROM62:426-437. SOUTHWEST XRF PAPER Table 1. X-ray fluorescence

  15. Air Fluorescence Relevant for Cosmic-Ray Detection - Summary of the 5th Fluorescence Workshop, El Escorial 2007

    E-Print Network [OSTI]

    Fernando Arqueros; Joerg R. Hoerandel; Bianca Keilhauer

    2008-07-24T23:59:59.000Z

    High-energy cosmic rays with energies exceeding $10^{17}$ eV are frequently observed by measurements of the fluorescence light induced by air showers. A major contribution to the systematic uncertainties of the absolute energy scale of such experiments is the insufficient knowledge of the fluorescence light yield of electrons in air. The aim of the 5th Fluorescence Workshop was to bring together experimental and theoretical expertise to discuss the latest progress on the investigations of the fluorescence light yield. The results of the workshop will be reviewed as well as the present status of knowledge in this field. Emphasis is given to the fluorescence light yield important for air shower observations and its dependence on atmospheric parameters, like pressure, temperature, and humidity. The effects of the latest results on the light observed from air showers will be discussed.

  16. Compact Object Formation and the Supernova Explosion Engine

    E-Print Network [OSTI]

    Fryer, C L

    2013-01-01T23:59:59.000Z

    When a massive star ends its life, its core collapses, forming a neutron star or black hole and producing some of the most energetic explosions in the universe. Core-collapse supernovae and long-duration gamma-ray bursts are the violent signatures of compact remnant formation. As such, both fields are intertwined and, coupled with theory, observations of transients can help us better understand compact remnants just as neutron star and black hole observations can constrain the supernova and gamma-ray burst engine. We review these ties in this paper.

  17. Plasma Frequency Shift Due to a Slowly Rotating Compact Star

    E-Print Network [OSTI]

    Babur M. Mirza; Hamid Saleem

    2005-05-10T23:59:59.000Z

    We investigate the effects of a slowly rotating compact gravitational source on electron oscillations in a homogeneous electrically neutral plasma in the absence of an external electric or magnetic field. Neglecting the random thermal motion of the electrons we assume the gravitoelectromagnetic approximation to the general theory of relativity for the gravitational field. It is shown that there is a shift in the plasma frequency and hence in the dielectric constant of the plasma due to the gravitomagnetic force. We also give estimates for the difference in the frequency of radially transmitted electromagnetic signals for typical compact star candidates.

  18. Compact stars in the standard model - and beyond

    E-Print Network [OSTI]

    F. Sandin

    2004-10-18T23:59:59.000Z

    In the context of the standard model of particle physics, there is a definite upper limit to the density of stable compact stars. However, if there is a deeper layer of constituents, below that of quarks and leptons, stability may be re-established far beyond this limiting density and a new class of compact stars could exist. These objects would cause gravitational lensing of white dwarfs and gamma-ray bursts, which might be observable as a diffraction pattern in the spectrum. Such observations could provide means for obtaining new clues about the fundamental particles and the origin of cold dark matter.

  19. A study of hand tamper design for compaction of soils

    E-Print Network [OSTI]

    McDonough, Brian

    1961-01-01T23:59:59.000Z

    Determination Standard Oven Dry Method versus Frying Pan Method Grain Size Distribution Curve Centerville Sand 34 Tamper Comparison Chart: Dry Density after 200 Blows per Square Foot of Layer Dry Density versus Compactive Effort Curve on 3. 0 Inch Square... of Utah revealed that a point exists at which an ultimate density is obtained, and any further increase in compaction effort results in lower than ultimate values. Shear Stress and Beari Ca acit If the resistance in a soil is exceeded by applied loads...

  20. Creation of a Compact Topologically Nontrivial Inflationary Universe

    E-Print Network [OSTI]

    Andrei Linde

    2004-09-11T23:59:59.000Z

    If inflation can occur only at the energy density V much smaller than the Planck density, which is the case for many inflationary models based on string theory, then the probability of quantum creation of a closed or an infinitely large open inflationary universe is exponentially suppressed for all known choices of the wave function of the universe. Meanwhile under certain conditions there is no exponential suppression for creation of topologically nontrivial compact flat or open inflationary universes. This suggests, contrary to the standard textbook lore, that compact flat or open universes with nontrivial topology should be considered a rule rather than an exception.

  1. Infiltration of nickel into alumina compact by electrodeposition

    SciTech Connect (OSTI)

    Hirata, Yoshihiro; Kyoda, Hideharu; Iwamoto, Takayuki [Kagoshima Univ. (Japan)

    1995-09-01T23:59:59.000Z

    Ni metal was electrodeposited into pores of an alumina compact in the aqueous solution of nickel nitrate/urea/ethylene glycol/ammonium sulfate. The Ni{sup 2+} ions in pores of the alumina compact deposited in proportion to t{sup 0.45}-t{sup 0.61} of deposition time (t) on Au electrode sputtered on the alumina surface. The deposition rate of Ni was higher for direct current than pulsed current Nickel grew dendritically in the alumina pores.

  2. Compact two-beam push-pull free electron laser

    DOE Patents [OSTI]

    Hutton, Andrew (Yorktown, VA)

    2009-03-03T23:59:59.000Z

    An ultra-compact free electron laser comprising a pair of opposed superconducting cavities that produce identical electron beams moving in opposite directions such that each set of superconducting cavities accelerates one electron beam and decelerates the other electron beam. Such an arrangement, allows the energy used to accelerate one beam to be recovered and used again to accelerate the second beam, thus, each electron beam is decelerated by a different structure than that which accelerated it so that energy exchange rather than recovery is achieved resulting in a more compact and highly efficient apparatus.

  3. Ship response using a compact wave spectrum model 

    E-Print Network [OSTI]

    Linn, Larry Donald

    1985-01-01T23:59:59.000Z

    SHIP RESPONSE USIM6 A COMPACT HAVE SPECTRUH HODEL A Thesis by LARRY DONALD LINN Submitted to the 6raduate College of Texas A&M University in partial fulfillment of the requirements for the degree of MASTER OF SCIENCE May 1985 Major Subject...: Ocean Engineering SHIP RESPONSE USIN6 A COMPACT 'NAVE SPECTRUN MODEL A Thesis by LARRY DONALD LINN Approved as to style and content by: John M. Niedzwec i (Chairman of Committee) Lee L. Lowery (Member) John M. Klinck (Member) Donald Mc...

  4. Ultrahigh resolution multicolor colocalization of single fluorescent probes

    DOE Patents [OSTI]

    Weiss, Shimon; Michalet, Xavier; Lacoste, Thilo D.

    2005-01-18T23:59:59.000Z

    A novel optical ruler based on ultrahigh-resolution colocalization of single fluorescent probes is described. Two unique families of fluorophores are used, namely energy-transfer fluorescent beads and semiconductor nanocrystal (NC) quantum dots, that can be excited by a single laser wavelength but emit at different wavelengths. A novel multicolor sample-scanning confocal microscope was constructed which allows one to image each fluorescent light emitter, free of chromatic aberrations, by scanning the sample with nanometer scale steps using a piezo-scanner. The resulting spots are accurately localized by fitting them to the known shape of the excitation point-spread-function of the microscope.

  5. Fluorescent lamp unit with magnetic field generating means

    DOE Patents [OSTI]

    Grossman, M.W.; George, W.A.

    1989-08-08T23:59:59.000Z

    A fluorescent lamp unit having a magnetic field generating means for improving the performance of the fluorescent lamp is disclosed. In a preferred embodiment the fluorescent lamp comprises four longitudinally extending leg portions disposed in substantially quadrangular columnar array and joined by three generally U-shaped portions disposed in different planes. In another embodiment of the invention the magnetic field generating means comprises a plurality of permanent magnets secured together to form a single columnar structure disposed within a centrally located region defined by the shape of lamp envelope. 4 figs.

  6. On extendability of group actions on compact Riemann surfaces

    E-Print Network [OSTI]

    Conder, Marston

    of such groups. The associated signatures appear in Table 1 below, the #12;rst eight corresponding to normalOn extendability of group actions on compact Riemann surfaces E. Bujalance #3; , F.J. Cirre y , M.D.E. Conder z 28 September 2001 Abstract The question of whether a given group G which acts faithfully

  7. Fouling characteristics of compact heat exchangers and enhanced tubes.

    SciTech Connect (OSTI)

    Panchal, C. B.; Rabas, T. J.

    1999-07-15T23:59:59.000Z

    Fouling is a complex phenomenon that (1) encompasses formation and transportation of precursors, and (2) attachment and possible removal of foulants. A basic understanding of fouling mechanisms should guide the development of effective mitigation techniques. The literature on fouling in complex flow passages of compact heat exchangers is limited; however, significant progress has been made with enhanced tubes.

  8. Disk-shaped Compact Tension Test for Asphalt Concrete Fracture

    E-Print Network [OSTI]

    Paulino, Glaucio H.

    Disk-shaped Compact Tension Test for Asphalt Concrete Fracture by M.P.Wagoner, W.G. Buttlar and G geometry is the ability to test cylindrical cores obtained from in-place asphalt concrete pavements finalizing the specimen geometry, a typical asphalt concrete surface mixture was tested at various

  9. GRI-04/0067 Evaluation of Soil Compaction

    E-Print Network [OSTI]

    & Pipeline Technology Division Gas Technology Institute 1700 South Mount Prospect Road Des Plaines, IL 60018GRI-04/0067 Evaluation of Soil Compaction Measuring Devices FINAL REPORT Prepared by Distribution Prepared for Gas Research Institute GTI Contract Number 15090 GRI Contract Number 8575 March 2005 #12;ii

  10. SURFING A WAVE TO COMPACT LASER TECHNOLOGY December 10 2007

    E-Print Network [OSTI]

    Strathclyde, University of

    to waves trailing behind a moving boat and small bunches of electrons can gather energy from the waveSURFING A WAVE TO COMPACT LASER TECHNOLOGY December 10 2007 New laser-based technology could laser pulses can be fired into plasma to create a wake and its huge electric fields can be harnessed

  11. Recent progress on the Compact Ignition Tokamak (CIT)

    SciTech Connect (OSTI)

    Ignat, D.W.

    1987-01-01T23:59:59.000Z

    This report describes work done on the Compact Ignition Tokamak (CIT), both at the Princeton Plasma Physics Laboratory (PPPL) and at other fusion laboratories in the United States. The goal of CIT is to reach ignition in a tokamak fusion device in the mid-1990's. Scientific and engineering features of the design are described, as well as projected cost and schedule.

  12. Compact Representation of Coordinated Sampling Policies for Body Sensor Networks

    E-Print Network [OSTI]

    Panangadan, Anand

    .Talukder@jpl.nasa.gov Abstract Embedded sensors of a Body Sensor Network need to efficiently utilize their energy resources Department of Electrical Engineering Los Angeles, CA 90089, USA 1-213-821-0871 {lius,raghu}@usc.edu 2 of a compact representation is feasible with little loss in performance. The global optimal policy is computed

  13. Corona performance of a compact 230-kV line

    SciTech Connect (OSTI)

    Chartier, V.L.; Blair, D.E. [Bonneville Power Administration, Vancouver, WA (United States). Division of Laboratories; Easley, M.D.; Raczkowski, R.T. [Puget Sound Power and Light Co., Bellevue, WA (United States)

    1994-12-31T23:59:59.000Z

    Permitting requirements and the acquisition of new rights-of-way for transmission facilities has in recent years become increasingly difficult for most utilities, including Puget Sound Power and Light Company. In order to maintain a high degree of reliability of service while being responsive to public concerns regarding the siting of high voltage (HV) transmission facilities, Puget Power has found it necessary to more heavily rely upon the use of compact lines in franchise corridors. Compaction does, however, precipitant increased levels of audible noise (AN) and radio and TV interference (RI and TVI) due to corona on the conductors and insulator assemblies. Puget Power relies upon the Bonneville Power Administration (BPA) Corona and Field Effects computer program to calculate AN and RI for new lines. Since there was some question of the program`s ability to accurately represent quiet 230-kV compact designs, a joint project was undertaken with BPA to verify the program`s algorithms. Long-term measurements made on an operating Puget Power 230-kV compact line confirmed the accuracy of BPA`s AN model; however, the RI measurements were much lower than predicted by the BPA computer and other programs. This paper also describes how the BPA computer program can be used to calculate the voltage needed to expose insulator assemblies to the correct electric field in single test setups in HV laboratories.

  14. Corona performance of a compact 230-kV line

    SciTech Connect (OSTI)

    Chartier, V.L.; Blair, D.E. [Bonneville Power Administration, Vancouver, WA (United States). Division of Labs.] [Bonneville Power Administration, Vancouver, WA (United States). Division of Labs.; Easley, M.D.; Raczkowski, R.T. [Puget Sound Power and Light Co., Bellevue, WA (United States)] [Puget Sound Power and Light Co., Bellevue, WA (United States)

    1995-01-01T23:59:59.000Z

    Permitting requirements and the acquisition of new rights-of-way for transmission facilities has in recent years become increasingly difficult for most utilities, including Puget Sound Power and Light Company. In order to maintain a high degree of reliability of service while being responsive to public concerns regarding the siting of high voltage (HV) transmission facilities, Puget Power has found it necessary to more heavily rely upon the use of compact lines in franchise corridors. Compaction does, however, precipitate increased levels of audible noise (AN) and radio and TV interference (RI and TVI) due to corona on the conductors and insulator assemblies. Puget Power relies upon the Bonneville Power Administration (BPA) Corona and Field Effects computer program to calculate AN and RI for new lines. Since there was some question of the program`s ability to accurately represent quiet 230-kV compact designs, a joint project was undertaken with BPA to verify the program`s algorithms. Long-term measurements made on an operating Puget Power 230-kV compact line confirmed the accuracy of BPA`s AN model; however, the RI measurements were much lower than predicted by the BPA and other programs. This paper also describes how the BPA computer program can be used to calculate the voltage needed to expose insulator assemblies to the correct electric field in single test setups in HV laboratories.

  15. A Compact Wireless Charging System for Electric Vehicles

    SciTech Connect (OSTI)

    Ning, Puqi [ORNL] [ORNL; Miller, John M [ORNL] [ORNL; Onar, Omer C [ORNL] [ORNL; White, Cliff P [ORNL] [ORNL

    2013-01-01T23:59:59.000Z

    In this paper, a compact high efficiency wireless power transfer system has been designed and developed. The detailed gate drive design, cooling system design, power stage development, and system assembling are presented. The successful tests verified the feasibility of wireless power transfer system to achieve over-all 90% efficiency.

  16. A New Compact Multichannel Receiver for Underwater Wireless Communication Networks

    E-Print Network [OSTI]

    Abdi, Ali

    size of the proposed receiver makes it particularly useful for small unmanned underwater vehicles1 A New Compact Multichannel Receiver for Underwater Wireless Communication Networks Ali Abdi of the particle velocity, in addition to the pressure, multichannel reception can be accomplished in underwater

  17. Compact anhydrous HCl to aqueous HCl conversion system

    DOE Patents [OSTI]

    Grossman, M.W.; Speer, R.

    1993-06-01T23:59:59.000Z

    The present invention is directed to an inexpensive and compact apparatus adapted for use with a [sup 196]Hg isotope separation process and the conversion of anhydrous HCl to aqueous HCl without the use of air flow to carry the HCl vapor into the converter system.

  18. Compact anhydrous HCl to aqueous HCl conversion system

    SciTech Connect (OSTI)

    Grossman, Mark W. (Belmont, MA); Speer, Richard (S. Hamilton, MA)

    1993-01-01T23:59:59.000Z

    The present invention is directed to an inexpensive and compact apparatus adapted for use with a .sup.196 Hg isotope separation process and the conversion of anhydrous HCl to aqueous HCl without the use of air flow to carry the HCl vapor into the converter system.

  19. Analysis of Time Series Using Compact Model-Based Descriptions

    E-Print Network [OSTI]

    Kriegel, Hans-Peter

    Analysis of Time Series Using Compact Model-Based Descriptions Hans-Peter Kriegel, Peer Kr this is a combination of the coefficients 1, . . . , 3 representing the three input time series using a function f-of-the-art compression methods. The results are visually presented in a very concise way so that the user can easily

  20. MissionBased Compact The Commonwealth of Australia

    E-Print Network [OSTI]

    Viglas, Anastasios

    ;Page 2 CONTENTS Attachments A. Indicative list of Commonwealth Funding provided to the University which is administered by DEEWR and relevant to this Compact. B. List of Commonwealth Funding provided to the University and Workplace Relations and the University about Performance Funding. E. Copy of Commonwealth Grant Scheme

  1. Ultra-compact Marx-type high-voltage generator

    DOE Patents [OSTI]

    Goerz, David A. (Brentwood, CA); Wilson, Michael J. (Modesto, CA)

    2000-01-01T23:59:59.000Z

    An ultra-compact Marx-type high-voltage generator includes individual high-performance components that are closely coupled and integrated into an extremely compact assembly. In one embodiment, a repetitively-switched, ultra-compact Marx generator includes low-profile, annular-shaped, high-voltage, ceramic capacitors with contoured edges and coplanar extended electrodes used for primary energy storage; low-profile, low-inductance, high-voltage, pressurized gas switches with compact gas envelopes suitably designed to be integrated with the annular capacitors; feed-forward, high-voltage, ceramic capacitors attached across successive switch-capacitor-switch stages to couple the necessary energy forward to sufficiently overvoltage the spark gap of the next in-line switch; optimally shaped electrodes and insulator surfaces to reduce electric field stresses in the weakest regions where dissimilar materials meet, and to spread the fields more evenly throughout the dielectric materials, allowing them to operate closer to their intrinsic breakdown levels; and uses manufacturing and assembly methods to integrate the capacitors and switches into stages that can be arranged into a low-profile Marx generator.

  2. Laser wakefield simulations towards development of compact particle accelerators

    E-Print Network [OSTI]

    Geddes, Cameron Guy Robinson

    Laser wakefield simulations towards development of compact particle accelerators C.G.R. Geddes1, D understanding of accelerator physics to advance beam performance and stability, and particle simulations model, France; 9 Oxford University, UK E-mail: cgrgeddes@lbl.gov Abstract. Laser driven wakefield accelerators

  3. THE CLASSIFICATION OF EXCEPTIONAL CDQL WEBS ON COMPACT COMPLEX SURFACES

    E-Print Network [OSTI]

    Pereira, Jorge Vitório

    THE CLASSIFICATION OF EXCEPTIONAL CDQL WEBS ON COMPACT COMPLEX SURFACES J. V. PEREIRA AND L. PIRIO Abstract. Codimension one webs are configurations of finitely many codi- mension one foliations in general equation among the first integrals of the foliations defining the web reminiscent of Abel's addition the

  4. Carbon RRLs Carbon RRLs towards Ultra-compact HII Regions

    E-Print Network [OSTI]

    Balser, Dana S.

    Carbon RRLs Carbon RRLs towards Ultra-compact HII Regions Dana S. Balser D. Anish Roshi (Raman (Agnes Scott College) #12;Carbon RRLs Carbon Radio Recombination Lines (RRLs) NGC 2024 (Orion B) IC 1795 (W3) Palmer et al. (1967) #12;Carbon RRLs Photodissociation Regions (PDRs) Hollenbach & Tielens (1997

  5. Exploratory Divertor Heat Load Studies for Compact Stellarator Reactors

    E-Print Network [OSTI]

    Raffray, A. René

    of the divertor system is described in Sec. III, together with the plate heat load profile, and the conditions is power reaching the plate, AD is the total plate area, Wpk is the design peak heat load limitExploratory Divertor Heat Load Studies for Compact Stellarator Reactors T.K. Maua , H. Mc

  6. Compact X-ray Light Source Workshop Report

    SciTech Connect (OSTI)

    Thevuthasan, Suntharampillai; Evans, James E.; Terminello, Louis J.; Koppenaal, David W.; Manke, Kristin L.; Plata, Charity

    2012-12-01T23:59:59.000Z

    This report, produced jointly by EMSL and FCSD, is the result of a workshop held in September 2011 that examined the utility of a compact x-ray light source (CXLS) in addressing many scientific challenges critical to advancing energy science and technology.

  7. Wavelet Occupancy Grids: a Method for Compact Map Building

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    Wavelet Occupancy Grids: a Method for Compact Map Building Manuel Yguel, Olivier Aycard for multi-resolution map building based on wavelets, which we call the wavelet occupancy grid (WavOG). Pai representation and data storage for large maps, under the constraints of multi-sensor real-time updates

  8. Sustainable LED Fluorescent Light Replacement Technology

    SciTech Connect (OSTI)

    None

    2011-06-30T23:59:59.000Z

    Ilumisys and the National Center for Manufacturing Sciences (NCMS) partnered on a three-year project awarded by the United States (U.S.) Department of Energy (DOE), to quantify the impacts of LED lamps, incandescent lamps and fluorescent benchmark lamps over a product lifecycle – i.e. to develop a sustainable design and manufacturing strategy that addresses product manufacturing, use, recycling and disposal scenarios for LED-based lighting. Based on the knowledge gained from extensive product tear-down studies of fluorescent and screw-in lighting products, lifecycle assessment tools, and accelerated lifecycle testing protocols, an interactive Sustainable LED Design Guide has been developed to aid architectural and lighting designers and engineers in making design decisions that consider three important environmental impacts (greenhouse gas emissions, energy use and mercury emission) across all phases of the life of an LED lighting product. Critical information developed for the lifecycle analysis and product feature comparisons is the useful life of the lighting product as well as its performance. The Design Guide is available at www.ncms.org, and was developed based on operational and durability testing of a variety of lighting products including power consumption, light output, and useful life of a lamp in order to allow a more realistic comparison of lamp designs. This report describes the main project tasks, results and innovative features of the lifecycle assessment (LCA)-based design tools, and the key considerations driving the sustainable design of LED lighting systems. The Design Guide incorporates the following three novel features for efficiently evaluating LED lighting features in value-chains: • Bill-of-Materials (BOM) Builder – Designers may import process data for each component and supply functional data for the product, including power, consumption, lumen output and expected useful life. • Environmental Impact Review – Designs are comparable across lifecycle phases, subsystems, and environmental impact category, and can be normalized to a userdefined functional unit. • Drill-down Review – These provide an indepth look at individual lamp designs with the ability to review across subsystem or lifecycle phase.

  9. COSMOLOGICAL SIMULATIONS OF MASSIVE COMPACT HIGH-z GALAXIES

    SciTech Connect (OSTI)

    Sommer-Larsen, J.; Toft, S., E-mail: jslarsen@astro.ku.d, E-mail: sune@dark-cosmology.d [Dark Cosmology Centre, Niels Bohr Institute, University of Copenhagen, Juliane Mariesvej 30, DK-2100 Copenhagen (Denmark)

    2010-10-01T23:59:59.000Z

    In order to investigate the structure and dynamics of the recently discovered massive (M{sub *} {approx}> 10{sup 11} M{sub sun}) compact z {approx} 2 galaxies, cosmological hydrodynamical/N-body simulations of a {approx}50,000 Mpc{sup 3} comoving (Lagrangian), proto-cluster region have been undertaken. At z = 2, the highest resolution simulation contains {approx}5800 resolved galaxies, of which 509, 27, and 5 have M{sub *}>10{sup 10} M{sub sun}, M{sub *}>10{sup 11} M{sub sun}, and M{sub *}>4 x 10{sup 11} M{sub sun}, respectively. Total stellar masses, effective radii, and characteristic stellar densities have been determined for all galaxies. At z = 2, for the definitely well-resolved mass range of M{sub *} {approx}> 10{sup 11} M{sub sun}, we fit the relation R{sub eff} = R{sub eff,12} M {sup 1/3}{sub *,12} to the data, where M{sub *,12} is the total stellar mass in units of 10{sup 12} M{sub sun}. This yields R{sub eff,12} = (1.20 {+-} 0.04) kpc, in line with observational findings for compact z {approx} 2 galaxies, though somewhat more compact than the observed average. The only line-of-sight velocity dispersion measured for a z {approx} 2 compact galaxy is very large, {sigma}{sub *,p} = 510{sup +165}{sub -95} km s{sup -1}. This value can be matched at about the 1{sigma} level, although a somewhat larger mass than the estimated M{sub *} {approx_equal} 2 x 10{sup 11} M{sub sun} is indicated. For the above mass range, the galaxies have an average axial ratio (b/a) = 0.64 {+-} 0.02 with a dispersion of 0.1, and an average rotation to one-dimensional velocity-dispersion ratio (v/{sigma}) = 0.46 {+-} 0.06 with a dispersion of 0.3, and a maximum value of v/{sigma} {approx_equal} 1.1. Both rotation and velocity anisotropy contribute significantly in flattening the compact galaxies. Some of the observed compact galaxies appear flatter than any of the simulated galaxies. Finally, it is found that the massive compact galaxies are strongly baryon dominated in their inner parts, with typical dark matter mass fractions of order only 20% inside of r = 2 R{sub eff}.

  10. Ceramographic Examinations of Irradiated AGR-1 Fuel Compacts

    SciTech Connect (OSTI)

    Paul Demkowicz; Scott Ploger; John Hunn; Jay S. Kehn

    2012-09-01T23:59:59.000Z

    The AGR 1 experiment involved irradiating 72 cylindrical fuel compacts containing tri-structural isotropic (TRISO)-coated particles to a peak burnup of 19.5% fissions per initial metal atom with no in-pile failures observed out of almost 300,000 particles. Six irradiated AGR 1 fuel compacts were selected for microscopy that span a range of irradiation conditions (temperature, burnup, and fast fluence). These six compacts also included all four TRISO coating variations irradiated in the AGR experiment. The six compacts were cross-sectioned both transversely and longitudinally, mounted, ground, and polished after development of careful techniques for preserving particle structures against preparation damage. From 36 to 79 particles within each cross section were exposed near enough to midplane for optical microscopy of kernel, buffer, and coating behavior. The microstructural analysis focused on kernel swelling and porosity, buffer densification and fracture, debonding between the buffer and inner pyrolytic carbon (IPyC) layers, and fractures in the IPyC and SiC layers. Three basic particle morphologies were established according to the extent of bonding between the buffer and IPyC layers: complete debonding along the interface (Type A), no debonding along the interface (Type B), and partial debonding (Type AB). These basic morphologies were subdivided according to whether the buffer stayed intact or fractured. The resulting six characteristic morphologies were used to classify particles within each cross section, but no spatial patterns were clearly observed in any of the cross-sectional morphology maps. Although positions of particle types appeared random within compacts, examining a total of 931 classified particles allowed other relationships among morphological types to be established.

  11. Ceramographic Examinations of Irradiated AGR-1 Fuel Compacts

    SciTech Connect (OSTI)

    Paul Demkowicz; Scott Ploger; John Hunn

    2012-05-01T23:59:59.000Z

    The AGR 1 experiment involved irradiating 72 cylindrical fuel compacts containing tri-structural isotropic (TRISO)-coated particles to a peak burnup of 19.5% fissions per initial metal atom with no in-pile failures observed out of almost 300,000 particles. Five irradiated AGR 1 fuel compacts were selected for microscopy that span a range of irradiation conditions (temperature, burnup, and fast fluence). These five compacts also included all four TRISO coating variations irradiated in the AGR experiment. The five compacts were cross-sectioned both transversely and longitudinally, mounted, ground, and polished after development of careful techniques for preserving particle structures against preparation damage. Approximately 40 to 80 particles within each cross section were exposed near enough to mid-plane for optical microscopy of kernel, buffer, and coating behavior. The microstructural analysis focused on kernel swelling and porosity, buffer densification and fracture, debonding between the buffer and inner pyrolytic carbon (IPyC) layers, and fractures in the IPyC and SiC layers. Three basic particle morphologies were established according to the extent of bonding between the buffer and IPyC layers: complete debonding along the interface (Type A), no debonding along the interface (Type B), and partial debonding (Type AB). These basic morphologies were subdivided according to whether the buffer stayed intact or fractured. The resulting six characteristic morphologies were used to classify particles within each cross section, but no spatial patterns were clearly observed in any of the cross-sectional morphology maps. Although positions of particle types appeared random within compacts, examining a total of 830 classified particles allowed other relationships among morphological types to be established.

  12. Safe and compact ammonia storage/delivery systems for SCR-DeNOX...

    Energy Savers [EERE]

    Safe and compact ammonia storagedelivery systems for SCR-DeNOX in automotive units Safe and compact ammonia storagedelivery systems for SCR-DeNOX in automotive units Presentation...

  13. Northwest Interstate Compact on Low-Level Radioactive Waste Management (Multiple States)

    Broader source: Energy.gov [DOE]

    The Northwest Interstate Compact on Low-Level Radioactive Waste Management, enacted in 1981, was ratified by Congress in 1985. The Compact is a cooperative effort of the party states to protect...

  14. FY08 Annual Report for Nuclear Resonance Fluorescence Imaging

    SciTech Connect (OSTI)

    Warren, Glen A.; Caggiano, Joseph A.

    2009-01-06T23:59:59.000Z

    FY08 annual report for project the "Nuclear Resonance Fluorescence Imaging" project. Reviews accomplishments of last 3 years, including U-235 signature search, comparison of different photon sources, and examination of NRF measurements using monochromatic photon source.

  15. Calibration of fluorescence resonance energy transfer in microscopy

    DOE Patents [OSTI]

    Youvan, Douglas C. (San Jose, CA); Silva, Christopher M. (Sunnyvale, CA); Bylina, Edward J. (San Jose, CA); Coleman, William J. (Moutain View, CA); Dilworth, Michael R. (Santa Cruz, CA); Yang, Mary M. (San Jose, CA)

    2002-09-24T23:59:59.000Z

    Imaging hardware, software, calibrants, and methods are provided to visualize and quantitate the amount of Fluorescence Resonance Energy Transfer (FRET) occurring between donor and acceptor molecules in epifluorescence microscopy. The MicroFRET system compensates for overlap among donor, acceptor, and FRET spectra using well characterized fluorescent beads as standards in conjunction with radiometrically calibrated image processing techniques. The MicroFRET system also provides precisely machined epifluorescence cubes to maintain proper image registration as the sample is illuminated at the donor and acceptor excitation wavelengths. Algorithms are described that pseudocolor the image to display pixels exhibiting radiometrically-corrected fluorescence emission from the donor (blue), the acceptor (green) and FRET (red). The method is demonstrated on samples exhibiting FRET between genetically engineered derivatives of the Green Fluorescent Protein (GFP) bound to the surface of Ni chelating beads by histidine-tags.

  16. LIGHT-INDUCED CHANGES IN THE FLUORESCENCE YIELD OF

    E-Print Network [OSTI]

    Govindjee

    given during the transient slightly hastens and heightens P. Methyl viologen, an exogenous system I fluorescence intensity is the redox state of Q, the electron acceptor in the system It reaction center (9). Fig

  17. THE HISTORY AND TECHNICAL EVOLUTION OF HIGH FREQUENCY FLUORESCENT LIGHTING

    E-Print Network [OSTI]

    Campbell, John H.

    2011-01-01T23:59:59.000Z

    Dec. 1953. "Hi-Volt-Cycle Lighting ~ Launched i n a Hi-Wide2, F e b r u a r y , 19 53. "Lighting Your Plant with Highg h Frequency Fluorescent Lighting John H. Campbell December

  18. Large core polymer optical backplanes for fluorescence detection

    E-Print Network [OSTI]

    Lee, Kevin Shao-Kwan

    2006-01-01T23:59:59.000Z

    Fluorescence based sensors are used for determining environmental parameters such as dissolved oxygen or pH in biological systems without disturbing a biological system's equilibrium. Recently, there has been a drive to ...

  19. REDUCING INCIDENTAL FLUORESCENCE IN LIVE CELL IMAGING A. Altinok 1

    E-Print Network [OSTI]

    California at Santa Barbara, University of

    , the technique is based on staining bio molecules selectively with proteins carrying fluorescence dyes of known. For instance, length measurements in Fig.1 would lack accuracy since the ends of the objects are blurry within

  20. SHORT COMMUNICATION The Chlorophyll Fluorescence Ratio F735/F700

    E-Print Network [OSTI]

    Gitelson, Anatoly

    sylvatica L.), elm (Ulmus minor 1988; Dahn et al., 1992). In green leaves, about 90% of Miller), and wild of reabsorption of the Chl fluorescence was quan- titatively estimated (Dahn et al., 1992; Gunther et al

  1. Calibration of fluorescence resonance energy transfer in microscopy

    DOE Patents [OSTI]

    Youvan, Dougalas C.; Silva, Christopher M.; Bylina, Edward J.; Coleman, William J.; Dilworth, Michael R.; Yang, Mary M.

    2003-12-09T23:59:59.000Z

    Imaging hardware, software, calibrants, and methods are provided to visualize and quantitate the amount of Fluorescence Resonance Energy Transfer (FRET) occurring between donor and acceptor molecules in epifluorescence microscopy. The MicroFRET system compensates for overlap among donor, acceptor, and FRET spectra using well characterized fluorescent beads as standards in conjunction with radiometrically calibrated image processing techniques. The MicroFRET system also provides precisely machined epifluorescence cubes to maintain proper image registration as the sample is illuminated at the donor and acceptor excitation wavelengths. Algorithms are described that pseudocolor the image to display pixels exhibiting radiometrically-corrected fluorescence emission from the donor (blue), the acceptor (green) and FRET (red). The method is demonstrated on samples exhibiting FRET between genetically engineered derivatives of the Green Fluorescent Protein (GFP) bound to the surface of Ni chelating beads by histidine-tags.

  2. Exploring the mechanome with optical tweezers and single molecule fluorescence

    E-Print Network [OSTI]

    Brau, Ricardo R. (Ricardo Rafael), 1979-

    2008-01-01T23:59:59.000Z

    The combination of optical tweezers and single molecule fluorescence into an instrument capable of making combined, coincident measurements adds an observable dimension that allows for the examination of the localized ...

  3. Protein subcellular localization assays using split fluorescent proteins

    DOE Patents [OSTI]

    Waldo, Geoffrey S. (Santa Fe, NM); Cabantous, Stephanie (Los Alamos, NM)

    2009-09-08T23:59:59.000Z

    The invention provides protein subcellular localization assays using split fluorescent protein systems. The assays are conducted in living cells, do not require fixation and washing steps inherent in existing immunostaining and related techniques, and permit rapid, non-invasive, direct visualization of protein localization in living cells. The split fluorescent protein systems used in the practice of the invention generally comprise two or more self-complementing fragments of a fluorescent protein, such as GFP, wherein one or more of the fragments correspond to one or more beta-strand microdomains and are used to "tag" proteins of interest, and a complementary "assay" fragment of the fluorescent protein. Either or both of the fragments may be functionalized with a subcellular targeting sequence enabling it to be expressed in or directed to a particular subcellular compartment (i.e., the nucleus).

  4. An Enhanced Monomeric Blue Fluorescent Protein with the High Chemical Stability of the Chromophore

    E-Print Network [OSTI]

    Verkhusha, Vladislav V.

    An Enhanced Monomeric Blue Fluorescent Protein with the High Chemical Stability of the Chromophore Commonly used monomeric blue fluorescent proteins suffer from moderate brightness. The brightest of them, m transition from a blue fluorescent state with absorbance at 401 nm to a non-fluorescent state with absorbance

  5. Development of laser excited atomic fluorescence and ionization methods

    SciTech Connect (OSTI)

    Winefordner, J.D.

    1991-01-01T23:59:59.000Z

    Progress report: May 1, 1988 to December 31, 1991. The research supported by DE-FG05-88ER13881 during the past (nearly) 3 years can be divided into the following four categories: (1) theoretical considerations of the ultimate detection powers of laser fluorescence and laser ionization methods; (2) experimental evaluation of laser excited atomic fluorescence; (3) fundamental studies of atomic and molecular parameters in flames and plasmas; (4) other studies.

  6. LucY: A Versatile New Fluorescent Reporter Protein

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Auldridge, Michele E.; Cao, Hongnan; Sen, Saurabh; Franz, Laura P.; Bingman, Craig A.; Yennamalli, Ragothaman M.; Phillips, George N.; Mead, David; Steinmetz, Eric J.; Michnick, Stephen W.

    2015-04-23T23:59:59.000Z

    We report on the discovery, isolation, and use of a novel yellow fluorescent protein. Lucigen Yellow (LucY) binds one FAD molecule within its core, thus shielding it from water and maintaining its structure so that fluorescence is 10-fold higher than freely soluble FAD. LucY displays excitation and emission spectra characteristic of FAD, with 3 excitation peaks at 276nm, 377nm, and 460nm and a single emission peak at 530nm. These excitation and emission maxima provide the large Stokes shift beneficial to fluorescence experimentation. LucY belongs to the MurB family of UDP-N-acetylenolpyruvylglucosamine reductases. The high resolution crystal structure shows that in contrastmore »to other structurally resolved MurB enzymes, LucY does not contain a potentially quenching aromatic residue near the FAD isoalloxazine ring, which may explain its increased fluorescence over related proteins. Using E. coli as a system in which to develop LucY as a reporter, we show that it is amenable to circular permutation and use as a reporter of protein-protein interaction. Fragmentation between its distinct domains renders LucY non-fluorescent, but fluorescence can be partially restored by fusion of the fragments to interacting protein domains. Thus, LucY may find application in Protein-fragment Complementation Assays for evaluating protein-protein interactions.« less

  7. Application of fluorescence microscopy to coal-derived resid characterization

    SciTech Connect (OSTI)

    Rathbone, R.F.; Hower, J.C.; Derbyshire, F.J.

    1991-01-01T23:59:59.000Z

    This study evaluates the usefulness of a fluorescence microscopy methodology to analyze coal-derived resids and interpret the data in the light of liquefaction processing conditions, process response, the inferred resid reactivity, and in relation to results of other analytical data. The fluorescence technique utilized has been widely applied to coal and kerogen characterization, albeit with some modifications, but is novel in its application to the characterization of coal liquids. Fluorescence is the emission of light energy which occurs when electrons, having been excited to a higher energy orbital, return to their lower energy ground state. The majority of organic molecules that fluoresce are those with conjugated double bonds (chromophores), such as aromatics, characterized by pi-electrons less strongly bound within the molecule than sigma electrons, that can be excited to anti-bonding pi-orbitals. Increasing the extent of pi-bond conjugation (i.e. larger molecular size) generally imparts a shift in absorption and emission spectra to longer wavelengths. Resid fluorescence largely depends on the concentration and degree of conjugation of aromatic chromophores in the high molecular weight liquids, possibly with ancillary effects from oxygen functionalities. In this context, fluorescence analysis of liquefaction resids can potentially evaluate process performance, since direct liquefaction processes endeavor to break down the macromolecular structure of coal, and reduce the molecular weight of polycondensed aromatics through hydrogenation, the opening of ring structures, and heteroatom removal.

  8. Application of fluorescence microscopy to coal-derived resid characterization

    SciTech Connect (OSTI)

    Rathbone, R.F.; Hower, J.C.; Derbyshire, F.J.

    1991-12-31T23:59:59.000Z

    This study evaluates the usefulness of a fluorescence microscopy methodology to analyze coal-derived resids and interpret the data in the light of liquefaction processing conditions, process response, the inferred resid reactivity, and in relation to results of other analytical data. The fluorescence technique utilized has been widely applied to coal and kerogen characterization, albeit with some modifications, but is novel in its application to the characterization of coal liquids. Fluorescence is the emission of light energy which occurs when electrons, having been excited to a higher energy orbital, return to their lower energy ground state. The majority of organic molecules that fluoresce are those with conjugated double bonds (chromophores), such as aromatics, characterized by pi-electrons less strongly bound within the molecule than sigma electrons, that can be excited to anti-bonding pi-orbitals. Increasing the extent of pi-bond conjugation (i.e. larger molecular size) generally imparts a shift in absorption and emission spectra to longer wavelengths. Resid fluorescence largely depends on the concentration and degree of conjugation of aromatic chromophores in the high molecular weight liquids, possibly with ancillary effects from oxygen functionalities. In this context, fluorescence analysis of liquefaction resids can potentially evaluate process performance, since direct liquefaction processes endeavor to break down the macromolecular structure of coal, and reduce the molecular weight of polycondensed aromatics through hydrogenation, the opening of ring structures, and heteroatom removal.

  9. Fusion Engineering and Design 81 (2006) 26792693 Recent progress in the ARIES compact stellarator study

    E-Print Network [OSTI]

    Najmabadi, Farrokh

    2006-01-01T23:59:59.000Z

    of compact stellarator power plants, ARIES-CS, was initiated recently to explore attractive compact are similar in size to advanced tokamak power plants. © 2006 Elsevier B.V. All rights reserved. Keywords: Fusion power plant; Compact stellarator Corresponding author. Tel.: +1 858 534 7869; fax: +1 858 822

  10. Steam-circuit Model for the Compact Linear Fresnel Reflector , G. L. Morrison1

    E-Print Network [OSTI]

    Steam-circuit Model for the Compact Linear Fresnel Reflector Prototype J. D. Pye1 , G. L. Morrison1.pye@student.unsw.edu.au Abstract The Compact Linear Fresnel Reflector (CLFR) is a linear-concentrating solar thermal energy system The Compact Linear Fresnel Reflector (CLFR) was first conceived of in 1992-1993 and was patented in 1995

  11. Prediction of Asphalt Mixture Compactability from Mixture, Asphalt, and Aggregate Properties

    E-Print Network [OSTI]

    Muras, Andrew J.

    2010-07-14T23:59:59.000Z

    . Predicted Plot of CV Neural Net of Entire Data Set for a ............................ 50 Figure 32. Predicted Plot of CV Neural Net of Entire Data Set for AV Nini ................... 51 Figure 33. a versus Predicted a... ................................................... 24 Table 5 HMA Mixing and Compaction Temperatures ............................................. 27 Table 6 Compaction Parameters a, c, and AV Nini ................................................... 38 Table 7 Compaction Parameters m1, m2...

  12. Rigidifying Fluorescent Linkers by Metal–Organic Framework Formation for Fluorescence Blue Shift and Quantum Yield Enhancement

    SciTech Connect (OSTI)

    Wei, Zhangwen; Gu, Zhi-Yuan; Arvapally, Ravi K.; Chen, Ying-Pin; Ivy, Joshua F.; Yakovenko, Andrey A.; Feng, Dawei; Omary, Mohammad A.; Zhou, Hong-Cai [UNT

    2014-06-11T23:59:59.000Z

    We demonstrate that rigidifying the structure of fluorescent linkers by structurally constraining them in metal–organic frameworks (MOFs) to control their conformation effectively tunes the fluorescence energy and enhances the quantum yield. Thus, a new tetraphenylethylene-based zirconium MOF exhibits a deep-blue fluorescent emission at 470 nm with a unity quantum yield (99.9 ± 0.5%) under Ar, representing ca. 3600 cm?¹ blue shift and doubled radiative decay efficiency vs the linker precursor. An anomalous increase in the fluorescence lifetime and relative intensity takes place upon heating the solid MOF from cryogenic to ambient temperatures. The origin of these unusual photoluminescence properties is attributed to twisted linker conformation, intramolecular hindrance, and framework rigidity.

  13. D-brane field theory on compact spaces

    E-Print Network [OSTI]

    Washington Taylor

    1996-11-07T23:59:59.000Z

    We consider Dirichlet p-branes in type II string theory on a space which has been toroidally compactified in d dimensions. We give an explicit construction of the field theory description of this system by putting a countably infinite number of copies of each brane on the noncompact covering space, and modding out the resulting gauge theory by Z^d. The resulting theory is a gauge theory with graded fields corresponding to strings winding around the torus an arbitrary number of times. In accordance with T-duality, this theory is equivalent to the gauge theory for the dual system of (d + p)-branes wrapped around the compact directions, where the winding number is exchanged for momentum in the compact direction.

  14. Compact and mobile high resolution PET brain imager

    DOE Patents [OSTI]

    Majewski, Stanislaw (Yorktown, VA); Proffitt, James (Newport News, VA)

    2011-02-08T23:59:59.000Z

    A brain imager includes a compact ring-like static PET imager mounted in a helmet-like structure. When attached to a patient's head, the helmet-like brain imager maintains the relative head-to-imager geometry fixed through the whole imaging procedure. The brain imaging helmet contains radiation sensors and minimal front-end electronics. A flexible mechanical suspension/harness system supports the weight of the helmet thereby allowing for patient to have limited movements of the head during imaging scans. The compact ring-like PET imager enables very high resolution imaging of neurological brain functions, cancer, and effects of trauma using a rather simple mobile scanner with limited space needs for use and storage.

  15. Flaw-detection characteristics of the compact MIB-4 betatron

    SciTech Connect (OSTI)

    Boiko, D.A.; Filimonov, A.A.; Chakhlov, V.L.

    1987-09-01T23:59:59.000Z

    The compact pulse betatron using electrons accelerated to an energy of up to 4 MeV (MIB-4) is designed for the radiographic inspection of reinforced-concrete structures and buildings, welded joints, various materials, and assemblies. Information which refines and complements the method of inspecting parts by means of the MIB-4 device is provided. The results obtained in testing this equipment abroad are given.

  16. Compact betatron with four controlling-field periodicity elements

    SciTech Connect (OSTI)

    Chakhlov, V.L.; Pushin, V.S.; Burov, G.I.; Zvontsov, A.A.; Zvorygin, V.P.; Zrelov, Yu.D.

    1987-01-01T23:59:59.000Z

    A compact 3-MeV betatron is described. The electromagnet of the betatron uses removable four-element poles, which form a magnetic field with azimuthal variation. The betatron accelerates 2 x 10/sup 10/ particles per cycle. The cycle repetition frequency is up to 400 Hz. The radius of the equilibrium orbit is 4.5 cm. The maximum interpole gap is 4 cm. The depth of magnetic-field variation on the equilibrium radius is 0.15.

  17. Microscopic analysis of irradiated AGR-1 coated particle fuel compacts

    SciTech Connect (OSTI)

    Scott A. Ploger; Paul A. Demkowicz; John D. Hunn; Jay S. Kehn

    2014-05-01T23:59:59.000Z

    The AGR-1 experiment involved irradiation of 72 TRISO-coated particle fuel compacts to a peak compact-average burnup of 19.5% FIMA with no in-pile failures observed out of 3 x 105 total particles. Irradiated AGR-1 fuel compacts have been cross-sectioned and analyzed with optical microscopy to characterize kernel, buffer, and coating behavior. Six compacts have been examined, spanning a range of irradiation conditions (burnup, fast fluence, and irradiation temperature) and including all four TRISO coating variations irradiated in the AGR-1 experiment. The cylindrical specimens were sectioned both transversely and longitudinally, then polished to expose from 36 to 79 individual particles near midplane on each mount. The analysis focused primarily on kernel swelling and porosity, buffer densification and fracturing, buffer–IPyC debonding, and fractures in the IPyC and SiC layers. Characteristic morphologies have been identified, 981 particles have been classified, and spatial distributions of particle types have been mapped. No significant spatial patterns were discovered in these cross sections. However, some trends were found between morphological types and certain behavioral aspects. Buffer fractures were found in 23% of the particles, and these fractures often resulted in unconstrained kernel protrusion into the open cavities. Fractured buffers and buffers that stayed bonded to IPyC layers appear related to larger pore size in kernels. Buffer–IPyC interface integrity evidently factored into initiation of rare IPyC fractures. Fractures through part of the SiC layer were found in only four classified particles, all in conjunction with IPyC–SiC debonding. Compiled results suggest that the deliberate coating fabrication variations influenced the frequencies of IPyC fractures and IPyC–SiC debonds.

  18. Simple and Compact Expressions for Neutrino Oscillation Probabilities in Matter

    E-Print Network [OSTI]

    Minakata, Hisakazu

    2015-01-01T23:59:59.000Z

    We reformulate perturbation theory for neutrino oscillations in matter with an expansion parameter related to the ratio of the solar to the atmospheric Delta m^2 scales. Unlike previous works, we use a renormalized basis in which certain first-order effects are taken into account in the zeroth-order Hamiltonian. Using this perturbation theory we derive extremely compact expressions for the neutrino oscillation probabilities in matter. We find, for example, that the $\

  19. Compact gas-insulated transformer. Fourteenth quarterly report

    SciTech Connect (OSTI)

    Not Available

    1983-08-01T23:59:59.000Z

    Objective is to develop a compact, more efficient, quieter transformer which does not rely on mineral oil insulation. Compressed SF/sub 6/ is used as the external insulation and polymer film as the insulation between turns. A separate liquid cooling system is also provided. This document reports progress made in design, mechanical, dielectric, short circuit, thermal, materials, prototype, accessories, commercialization, and system studies. (DLC)

  20. Compact-range coordinate system established using a laser tracker.

    SciTech Connect (OSTI)

    Gallegos, Floyd H.; Bryce, Edwin Anthony

    2006-12-01T23:59:59.000Z

    Establishing a Cartesian coordinate reference system for an existing Compact Antenna Range using the parabolic reflector is presented. A SMX (Spatial Metrix Corporation) M/N 4000 laser-based coordinate measuring system established absolute coordinates for the facility. Electric field characteristics with positional movement correction are evaluated. Feed Horn relocation for alignment with the reflector axis is also described. Reference points are established for follow-on non-laser alignments utilizing a theodolite.

  1. Compact Refractive Imaging Spectrometer Designs Utilizing Immersed Gratings

    DOE Patents [OSTI]

    Lerner, Scott A. (Livermore, CA); Bennett, Charles L. (Livermore, CA); Bixler, Jay V. (Oakland, CA); Kuzmenko, Paul J. (Livermore, CA); Lewis, Isabella T. (San Jose, CA)

    2005-07-26T23:59:59.000Z

    A compact imaging spectrometer comprising an entrance slit for directing light, a first means for receiving the light and focusing the light, an immersed diffraction grating that receives the light from the first means and defracts the light, a second means for receiving the light from the immersed diffraction grating and focusing the light, and an image plane that receives the light from the second means

  2. Ultra-Compact High-Efficiency Luminaire for General Illumination

    SciTech Connect (OSTI)

    Ted Lowes

    2012-04-08T23:59:59.000Z

    Cree has developed a new ultra-compact light emitting diode (LED) luminaire capable of providing high efficacy with excellent color quality that can lead to significant energy savings in todayâ??s commercial and retail applications. This success was based on an integrated development effort tailoring the LED component characteristics, optics, thermal management and driver design for the small footprint to achieve an overall system efficiency of â?¥ 70%. A new LED component was designed to provide high brightness and efficacy in a form factor that allowed for a small directional beam with a luminaire housing design able to dissipate the heat effectively using a small physical envelope. A very compact, 90% efficient driver was developed to meet the system performance while not taking away any thermal mass from the heat sink. A 91% efficient secondary optics was designed to maximize efficiency while providing a smooth beam. The reliability of the new LED component was robust under accelerated testing conditions. Luminaires were assembled integrating the novel LED component, secondary optics, heat sink and driver technology to demonstrate the system improvement. Cree has successfully completed this project by developing an ultra-compact LED luminaire that provided 380 lumens at a correlated color temperature (CCT) of 2822 K and color rendering index (CRI) of 94 with an efficacy of 94 lumens per watt (LPW) when operating at 4 W input power (steady state) with an overall system efficiency of 81%. At a higher input power of 9 Watts, the lamp provided 658 lumens at 71 LPW.

  3. VALIDATION OF A THERMAL CONDUCTIVITY MEASUREMENT SYSTEM FOR FUEL COMPACTS

    SciTech Connect (OSTI)

    Jeff Phillips; Colby Jensen; Changhu Xing; Heng Ban

    2011-03-01T23:59:59.000Z

    A high temperature guarded-comparative-longitudinal heat flow measurement system has been built to measure the thermal conductivity of a composite nuclear fuel compact. It is a steady-state measurement device designed to operate over a temperature range of 300 K to 1200 K. No existing apparatus is currently available for obtaining the thermal conductivity of the composite fuel in a non-destructive manner due to the compact’s unique geometry and composite nature. The current system design has been adapted from ASTM E 1225. As a way to simplify the design and operation of the system, it uses a unique radiative heat sink to conduct heat away from the sample column. A finite element analysis was performed on the measurement system to analyze the associated error for various operating conditions. Optimal operational conditions have been discovered through this analysis and results are presented. Several materials have been measured by the system and results are presented for stainless steel 304, inconel 625, and 99.95% pure iron covering a range of thermal conductivities of 10 W/m*K to 70 W/m*K. A comparison of the results has been made to data from existing literature.

  4. A Global 86GHz VLBI Survey of Compact Radio Sources

    E-Print Network [OSTI]

    Sang-Sung Lee; Andrei P. Lobanov; Thomas P. Krichbaum; Arno Witzel; J. Anton Zensus; Michael Bremer; Albert Greve; Michael Grewing

    2008-03-28T23:59:59.000Z

    We present results from a large 86GHz global VLBI survey of compact radio sources. The main goal of the survey is to increase by factors of 3--5 the total number of objects accessible for future 3-mm VLBI imaging. The survey observations reach the baseline sensitivity of 0.1Jy and image sensitivity of better than 10 mJy/beam. The total of 127 compact radio sources have been observed. The observations have yielded images for 109 sources, extending the database of the sources imaged at 86GHz with VLBI observation by a factor of 5, and only 6 sources have not been detected. The remaining 12 objects have been detected but could not be imaged due to insufficient closure phase information. Radio galaxies are less compact than quasars and BL Lacs on sub-milliarcsecond scale. Flux densities and sizes of core and jet components of all imaged sources have been estimated using Gaussian model fitting. From these measurements, brightness temperatures have been calculated, taking into account resolution limits of the data. The cores of 70% of the imaged sources are resolved. The core brightness temperatures of the sources peak at $\\sim 10^{11}$ K and only 1% have brightness temperatures higher than $10^{12}$ K. Cores of Intraday Variable (IDV) sources are smaller in angular size than non-IDV sources, and so yield higher brightness temperatures.

  5. EXPLORING THE INTERSTELLAR MEDIA OF OPTICALLY COMPACT DWARF GALAXIES

    SciTech Connect (OSTI)

    Most, Hans P.; Cannon, John M.; Engstrom, Eric; Fliss, Palmer [Department of Physics and Astronomy, Macalester College, 1600 Grand Avenue, Saint Paul, MN 55105 (United States); Salzer, John J. [Department of Astronomy, Indiana University, 727 East Third Street, Bloomington, IN 47405 (United States); Rosenberg, Jessica L., E-mail: hmost@macalester.edu, E-mail: jcannon@macalester.edu, E-mail: slaz@astro.indiana.edu, E-mail: jrosenb4@gmu.edu [School of Physics, Astronomy, and Computational Science, George Mason University, Fairfax, VA 22030 (United States)

    2013-06-15T23:59:59.000Z

    We present new Very Large Array H I spectral line, archival Sloan Digital Sky Survey, and archival Spitzer Space Telescope imaging of eight star-forming blue compact dwarf galaxies that were selected to be optically compact (optical radii <1 kpc). These systems have faint blue absolute magnitudes (M{sub B} {approx}> -17), ongoing star formation (based on emission-line selection by the H{alpha} or [O III] lines), and are nearby (mean velocity = 3315 km s{sup -1} {approx_equal} 45 Mpc). One galaxy in the sample, ADBS 113845+2008, is found to have an H I halo that extends 58 r-band scale lengths from its stellar body. In contrast, the rest of the sample galaxies have H I radii to optical-scale-length ratios ranging from 9.3 to 26. The size of the H I disk in the 'giant disk' dwarf galaxy ADBS 113845+2008 appears to be unusual as compared with similarly compact stellar populations.

  6. Cyanine-based probe\\tag-peptide pair fluorescence protein imaging and fluorescence protein imaging methods

    DOE Patents [OSTI]

    Mayer-Cumblidge, M. Uljana; Cao, Haishi

    2013-01-15T23:59:59.000Z

    A molecular probe comprises two arsenic atoms and at least one cyanine based moiety. A method of producing a molecular probe includes providing a molecule having a first formula, treating the molecule with HgOAc, and subsequently transmetallizing with AsCl.sub.3. The As is liganded to ethanedithiol to produce a probe having a second formula. A method of labeling a peptide includes providing a peptide comprising a tag sequence and contacting the peptide with a biarsenical molecular probe. A complex is formed comprising the tag sequence and the molecular probe. A method of studying a peptide includes providing a mixture containing a peptide comprising a peptide tag sequence, adding a biarsenical probe to the mixture, and monitoring the fluorescence of the mixture.

  7. Laser-induced differential normalized fluorescence method for cancer diagnosis

    DOE Patents [OSTI]

    Vo-Dinh, T.; Panjehpour, M.; Overholt, B.F.

    1996-12-03T23:59:59.000Z

    An apparatus and method for cancer diagnosis are disclosed. The diagnostic method includes the steps of irradiating a tissue sample with monochromatic excitation light, producing a laser-induced fluorescence spectrum from emission radiation generated by interaction of the excitation light with the tissue sample, and dividing the intensity at each wavelength of the laser-induced fluorescence spectrum by the integrated area under the laser-induced fluorescence spectrum to produce a normalized spectrum. A mathematical difference between the normalized spectrum and an average value of a reference set of normalized spectra which correspond to normal tissues is calculated, which provides for amplifying small changes in weak signals from malignant tissues for improved analysis. The calculated differential normalized spectrum is correlated to a specific condition of a tissue sample. 5 figs.

  8. Laser-induced differential normalized fluorescence method for cancer diagnosis

    DOE Patents [OSTI]

    Vo-Dinh, Tuan (Knoxville, TN); Panjehpour, Masoud (Knoxville, TN); Overholt, Bergein F. (Knoxville, TN)

    1996-01-01T23:59:59.000Z

    An apparatus and method for cancer diagnosis are disclosed. The diagnostic method includes the steps of irradiating a tissue sample with monochromatic excitation light, producing a laser-induced fluorescence spectrum from emission radiation generated by interaction of the excitation light with the tissue sample, and dividing the intensity at each wavelength of the laser-induced fluorescence spectrum by the integrated area under the laser-induced fluorescence spectrum to produce a normalized spectrum. A mathematical difference between the normalized spectrum and an average value of a reference set of normalized spectra which correspond to normal tissues is calculated, which provides for amplifying small changes in weak signals from malignant tissues for improved analysis. The calculated differential normalized spectrum is correlated to a specific condition of a tissue sample.

  9. Engineering and Characterization of a Superfolder Green Fluorescent Protein

    SciTech Connect (OSTI)

    Pedelacq,J.; Cabantous, S.; Tran, T.; Terwilliger, T.; Waldo, G.

    2006-01-01T23:59:59.000Z

    Existing variants of green fluorescent protein (GFP) often misfold when expressed as fusions with other proteins. We have generated a robustly folded version of GFP, called 'superfolder' GFP, that folds well even when fused to poorly folded polypeptides. Compared to 'folding reporter' GFP, a folding-enhanced GFP containing the 'cycle-3' mutations and the 'enhanced GFP' mutations F64L and S65T, superfolder GFP shows improved tolerance of circular permutation, greater resistance to chemical denaturants and improved folding kinetics. The fluorescence of Escherichia coli cells expressing each of eighteen proteins from Pyrobaculum aerophilum as fusions with superfolder GFP was proportional to total protein expression. In contrast, fluorescence of folding reporter GFP fusion proteins was strongly correlated with the productive folding yield of the passenger protein. X-ray crystallographic structural analyses helped explain the enhanced folding of superfolder GFP relative to folding reporter GFP.

  10. Fluorescent single walled nanotube/silica composite materials

    SciTech Connect (OSTI)

    Dattelbaum, Andrew M.; Gupta, Gautam; Duque, Juan G.; Doorn, Stephen K.; Hamilton, Christopher E.; DeFriend Obrey, Kimberly A.

    2013-03-12T23:59:59.000Z

    Fluorescent composites of surfactant-wrapped single-walled carbon nanotubes (SWNTs) were prepared by exposing suspensions of surfactant-wrapped carbon nanotubes to tetramethylorthosilicate (TMOS) vapor. Sodium deoxycholate (DOC) and sodium dodecylsulphate (SDS) were the surfactants. No loss in emission intensity was observed when the suspension of DOC-wrapped SWNTs were exposed to the TMOS vapors, but about a 50% decrease in the emission signal was observed from the SDS-wrapped SWNTs nanotubes. The decrease in emission was minimal by buffering the SDS/SWNT suspension prior to forming the composite. Fluorescent xerogels were prepared by adding glycerol to the SWNT suspensions prior to TMOS vapor exposure, followed by drying the gels. Fluorescent aerogels were prepared by replacing water in the gels with methanol and then exposing them to supercritical fluid drying conditions. The aerogels can be used for gas sensing.

  11. Photosynthesis: Research for Food, Fuel and Future--15th International Conference on Photosynthesis518 FLIM (Fluorescence Lifetime Imaging Microscopy) of Avocado Leaves during Slow

    E-Print Network [OSTI]

    Govindjee

    518 FLIM (Fluorescence Lifetime Imaging Microscopy) of Avocado Leaves during Slow Fluorescence avocado leaves (Persea americana Mill.) during the slow part of chlorophyll (Chl) a fluorescence transient

  12. Nuclear Resonance Fluorescence for Safeguards Applications

    SciTech Connect (OSTI)

    Ludewigt, Bernhard A; Quiter, Brian J; Ambers, Scott D

    2011-02-04T23:59:59.000Z

    In nuclear resonance fluorescence (NRF) measurements, resonances are excited by an external photon beam leading to the emission of {gamma} rays with specific energies that are characteristic of the emitting isotope. The promise of NRF as a non-destructive analysis technique (NDA) in safeguards applications lies in its potential to directly quantify a specific isotope in an assay target without the need for unfolding the combined responses of several fissile isotopes as often required by other NDA methods. The use of NRF for detection of sensitive nuclear materials and other contraband has been researched in the past. In the safeguards applications considered here one has to go beyond mere detection and precisely quantify the isotopic content, a challenge that is discussed throughout this report. Basic NRF measurement methods, instrumentation, and the analytical calculation of NRF signal strengths are described in Section 2. Well understood modeling and simulation tools are needed for assessing the potential of NRF for safeguards and for designing measurement systems. All our simulations were performed with the radiation transport code MCNPX, a code that is widely used in the safeguards community. Our initial studies showed that MCNPX grossly underestimated the elastically scattered background at backwards angles due to an incorrect treatment of Rayleigh scattering. While new, corrected calculations based on ENDF form factors showed much better agreement with experimental data for the elastic scattering of photons on an uranium target, the elastic backscatter is still not rigorously treated. Photonuclear scattering processes (nuclear Thomson, Delbruck and Giant Dipole Resonance scattering), which are expected to play an important role at higher energies, are not yet included. These missing elastic scattering contributions were studied and their importance evaluated evaluated against data found in the literature as discussed in Section 3. A transmission experiment was performed in September 2009 to test and demonstrate the applicability of the method to the quantitative measurement of an isotope of interest embedded in a thick target. The experiment, data analysis, and results are described in Section 4. The broad goal of our NRF studies is to assess the potential of the technique in safeguards applications. Three examples are analyzed in Section 5: the isotopic assay of spent nuclear fuel (SNF), the measurement of {sup 235}U enrichment in UF{sub 6} cylinders, and the determination of {sup 239}Pu in mixed oxide (MOX) fuel. The study of NRF for the assay of SNF assemblies was supported by the Next Generation Safeguards Initiative (NGSI) of the U.S. Department of Energy as part of a large multi-lab/university effort to quantify the plutonium (Pu) mass in spent nuclear fuel assemblies and to detect the diversion of pins with non-destructive assay (NDA) methods. NRF is one of 14 NDA techniques being researched. The methodology for performing and analyzing quantitative NRF measurements was developed for determining Pu mass in SNF and is extensively discussed in this report. The same methodology was applied to the assessment of NRF for the measurement of {sup 235}U enrichment and the determination of {sup 239}Pu in MOX fuel. The analysis centers on determining suitable NRF measurement methods, measurement capabilities that could be realized with currently available instrumentation, and photon source and detector requirements for achieving useful NDA capabilities.

  13. Preliminary results of post-irradiation examination of the AGR-1 TRISO fuel compacts

    SciTech Connect (OSTI)

    Paul Demkowicz; John Hunn; Robert Morris; Jason Harp; Philip Winston; Charles Baldwin; Fred Montgomery; Scott Ploger; Isabella van Rooyen

    2012-10-01T23:59:59.000Z

    Five irradiated fuel compacts from the AGR-1 experiment have been examined in detail in order to assess in-pile fission product release behavior. Compacts were electrolytically deconsolidated and analyzed using the leach-burn-leach technique to measure fission product inventory in the compact matrix and identify any particles with a defective SiC layer. Loose particles were then gamma counted to measure the fission product inventory. One particle with a defective SiC layer was found in the five compacts examined. The fractional release of Ag 110m from the particles was significant. The total fraction of silver released from all the particles within a compact ranged from 0-0.63 and individual particles within a single compact often exhibited a very wide range of silver release. The average fractional release of Eu-154 from all particles in a compact was 2.4×10-4—1.3×10-2, which is indicative of release through intact coatings. The fractional Cs-134 inventory in the compact matrix was <2×10-5 when all coatings remained intact, indicating good cesium retention. Approximately 1% of the palladium inventory was found in the compact matrix for two of the compacts, indicating significant release through intact coatings.

  14. Heat transfer assembly for a fluorescent lamp and fixture

    DOE Patents [OSTI]

    Siminovitch, M.J.; Rubenstein, F.M.; Whitman, R.E.

    1992-12-29T23:59:59.000Z

    In a lighting fixture including a lamp and a housing, a heat transfer structure is disclosed for reducing the minimum lamp wall temperature of a fluorescent light bulb. The heat transfer structure, constructed of thermally conductive material, extends from inside the housing to outside the housing, transferring heat energy generated from a fluorescent light bulb to outside the housing where the heat energy is dissipated to the ambient air outside the housing. Also disclosed is a method for reducing minimum lamp wall temperatures. Further disclosed is an improved lighting fixture including a lamp, a housing and the aforementioned heat transfer structure. 11 figs.

  15. An Event Reconstruction Method for the Telescope Array Fluorescence Detectors

    SciTech Connect (OSTI)

    Fujii, T.; Ogio, S.; Yamazaki, K. [Graduate Schiool of Science, Osaka City University, Sumiyoshi, Osaka 558-8585 (Japan); Fukushima, M.; Ikeda, D.; Sagawa, H.; Takahashi, Y.; Tameda, Y. [Institute of Cosmic Ray Research, University of Tokyo, Kashiwa, Chiba 277-8582 (Japan); Hayashi, K.; Ishimori, R.; Kobayashi, Y.; Tokuno, H.; Tsunesada, Y. [Graduate School of Science and Engineering, Tokyo Institute of Technology, Meguro, Tokyo 152-8551 (Japan); Honda, K.; Tomida, T. [Graduate School of Medicine and Engineering, University of Yamanashi, Kofu, Yamanashi 400-8511 (Japan); Udo, S. [Faculty of Engineering, Kanagawa University, Yokohama, Kanagawa 221-8686 (Japan)

    2011-09-22T23:59:59.000Z

    We measure arrival directions, energies and mass composition of ultra-high energy cosmic rays with air fluorescence detector telescopes. The longitudinal profile of the cosmic ray induced extensive air shower cascade is imaged on focal plane of the telescope camera. Here, we show an event reconstruction method to obtain the primary information from data collected by the Telescope Array Fluorescence Detectors. In particular, we report on an ''Inverse Monte Carlo (IMC)'' method in which the reconstruction process searches for an optimum solution via repeated Monte Carlo simulations including characteristics of all detectors, atmospheric conditions, photon emission and scattering processes.

  16. Longitudinal Shower Profile Reconstruction from Fluorescence and Cherenkov Light

    E-Print Network [OSTI]

    M. Unger; R. Engel; F. Schüssler; R. Ulrich

    2007-06-11T23:59:59.000Z

    Traditionally, longitudinal shower profiles are reconstructed in fluorescence light experiments by treating the Cherenkov light contribution as background. Here we will argue that, due to universality of the energy spectra of electrons and positrons, both fluorescence and Cherenkov light can be used simultaneously as signal to infer the longitudinal shower development. We present a new profile reconstruction method that is based on the analytic least-square solution for the estimation of the shower profile from the observed light signal and discuss the extrapolation of the profile with a Gaisser-Hillas function.

  17. A versatile detector for total fluorescence and electron yield experiments

    SciTech Connect (OSTI)

    Thielemann, N. [Institute for Methods and Instrumentation for Synchrotron Radiation Research, Helmholtz-Zentrum Berlin fuer Materialien und Energie GmbH, Albert-Einstein-Str. 15, 12489 Berlin (Germany); Institut fuer Physik, Humboldt-Universitaet zu Berlin, Newtonstrasse 15, 12489 Berlin (Germany); Hoffmann, P. [Institute for Methods and Instrumentation for Synchrotron Radiation Research, Helmholtz-Zentrum Berlin fuer Materialien und Energie GmbH, Albert-Einstein-Str. 15, 12489 Berlin (Germany); Foehlisch, A. [Institute for Methods and Instrumentation for Synchrotron Radiation Research, Helmholtz-Zentrum Berlin fuer Materialien und Energie GmbH, Albert-Einstein-Str. 15, 12489 Berlin (Germany); Institut fuer Physik und Astronomie, Universitaet Potsdam, Karl-Liebknecht-Strasse 24-25, 14476 Potsdam (Germany)

    2012-09-15T23:59:59.000Z

    The combination of a non-coated silicon photodiode with electron repelling meshes makes a versatile detector for total fluorescence yield and electron yield techniques highly suitable for x-ray absorption spectroscopy. In particular, a copper mesh with a bias voltage allows to suppress or transmit the electron yield signal. The performance of this detection scheme has been characterized by near edge x-ray absorption fine structure studies of thermal oxidized silicon and sapphire. The results show that the new detector probes both electron yield and for a bias voltage exceeding the maximum photon energy the total fluorescence yield.

  18. Heat transfer assembly for a fluorescent lamp and fixture

    SciTech Connect (OSTI)

    Siminovitch, Michael J. (Richmond, CA); Rubenstein, Francis M. (Berkeley, CA); Whitman, Richard E. (Richmond, CA)

    1992-01-01T23:59:59.000Z

    In a lighting fixture including a lamp and a housing, a heat transfer structure is disclosed for reducing the minimum lamp wall temperature of a fluorescent light bulb. The heat transfer structure, constructed of thermally conductive material, extends from inside the housing to outside the housing, transferring heat energy generated from a fluorescent light bulb to outside the housing where the heat energy is dissipated to the ambient air outside the housing. Also disclosed is a method for reducing minimum lamp wall temperatures. Further disclosed is an improved lighting fixture including a lamp, a housing and the aforementioned heat transfer structure.

  19. Microscopic analysis of irradiated AGR-1 coated particle fuel compacts

    SciTech Connect (OSTI)

    Scott Ploger; Paul Demkowicz; John Hunn; Robert Morris

    2012-10-01T23:59:59.000Z

    The AGR-1 experiment involved irradiation of 72 TRISO-coated particle fuel compacts to a peak burnup of 19.5% FIMA with no in-pile failures observed out of 3×105 total particles. Irradiated AGR-1 fuel compacts have been cross-sectioned and analyzed with optical microscopy to characterize kernel, buffer, and coating behavior. Five compacts have been examined so far, spanning a range of irradiation conditions (burnup, fast fluence, and irradiation temperature) and including all four TRISO coating variations irradiated in the AGR-1 experiment. The cylindrical specimens were sectioned both transversely and longitudinally, then polished to expose between approximately 40-80 individual particles on each mount. The analysis focused primarily on kernel swelling and porosity, buffer densification and fracturing, buffer-IPyC debonding, and fractures in the IPyC and SiC layers. Characteristic morphologies have been identified, over 800 particles have been classified, and spatial distributions of particle types have been mapped. No significant spatial patterns were discovered in these cross sections. However, some trends were found between morphological types and certain behavioral aspects. Buffer fractures were found in approximately 23% of the particles, and these fractures often resulted in unconstrained kernel swelling into the open cavities. Fractured buffers and buffers that stayed bonded to IPyC layers appear related to larger pore size in kernels. Buffer-IPyC interface integrity evidently factored into initiation of rare IPyC fractures. Fractures through part of the SiC layer were found in only three particles, all in conjunction with IPyC-SiC debonding. Compiled results suggest that the deliberate coating fabrication variations influenced the frequencies of IPyC fractures, IPyC-SiC debonds, and SiC fractures.

  20. COMPACT BINARY PROGENITORS OF SHORT GAMMA-RAY BURSTS

    SciTech Connect (OSTI)

    Giacomazzo, Bruno [JILA, University of Colorado and National Institute of Standards and Technology, Boulder, CO 80309 (United States); Perna, Rosalba [JILA and Department of Astrophysical and Planetary Sciences, University of Colorado, Boulder, CO 80309 (United States); Rezzolla, Luciano [Max-Planck-Institut fuer Gravitationsphysik, Albert-Einstein-Institut, Potsdam D-14476 (Germany); Troja, Eleonora [NASA Goddard Space Flight Center, Greenbelt, MD 20771 (United States); Lazzati, Davide [Department of Physics, NC State University, 2401 Stinson Drive, Raleigh, NC 27695-8202 (United States)

    2013-01-10T23:59:59.000Z

    In recent years, detailed observations and accurate numerical simulations have provided support to the idea that mergers of compact binaries containing either two neutron stars (NSs) or an NS and a black hole (BH) may constitute the central engine of short gamma-ray bursts (SGRBs). The merger of such compact binaries is expected to lead to the production of a spinning BH surrounded by an accreting torus. Several mechanisms can extract energy from this system and power the SGRBs. Here we connect observations and numerical simulations of compact binary mergers, and use the current sample of SGRBs with measured energies to constrain the mass of their powering tori. By comparing the masses of the tori with the results of fully general-relativistic simulations, we are able to infer the properties of the binary progenitors that yield SGRBs. By assuming a constant efficiency in converting torus mass into jet energy, {epsilon}{sub jet} = 10%, we find that most of the tori have masses smaller than 0.01 M{sub Sun }, favoring 'high-mass' binary NSs mergers, i.e., binaries with total masses {approx}> 1.5 the maximum mass of an isolated NS. This has important consequences for the gravitational wave signals that may be detected in association with SGRBs, since 'high-mass' systems do not form a long-lived hypermassive NS after the merger. While NS-BH systems cannot be excluded to be the engine of at least some of the SGRBs, the BH would need to have an initial spin of {approx}0.9 or higher.

  1. Compact cyclone filter train for radiological and hazardous environments

    DOE Patents [OSTI]

    Bench, T.R.

    1998-04-28T23:59:59.000Z

    A compact cyclone filter train is disclosed for the removal of hazardous and radiological particles from a gaseous fluid medium. This filter train permits a small cyclone separator to be used in a very small space envelope due to the arrangement of the filter housing adjacent to the separator with the cyclone separator and the filters mounted on a plate. The entire unit will have a hoist connection at the center of gravity so that the entire unit including the separator, the filters, and the base can be lifted and repositioned as desired. 3 figs.

  2. Compact collimated fiber optic array diagnostic for railgun plasma experiments

    SciTech Connect (OSTI)

    Tang, V; Solberg, J; Ferriera, T; Tully, L; Stephan, P

    2008-10-02T23:59:59.000Z

    We have developed and tested a compact collimated sixteen channel fiber optic array diagnostic for studying the light emission of railgun armature plasmas with {approx}mm spatial and sub-{micro}s temporal resolution. The design and operational details of the diagnostic are described. Plasma velocities, oscillation, and dimension data from the diagnostic for the Livermore Fixed Hybrid Armature experiment are presented and compared with 1-D simulations. The techniques and principles discussed allow the extension of the diagnostic to other railgun and related dense plasma experiments.

  3. Porous silicon ring resonator for compact, high sensitivity biosensing applications

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Rodriguez, Gilberto A.; Hu, Shuren; Weiss, Sharon M.

    2015-01-01T23:59:59.000Z

    A ring resonator is patterned on a porous silicon slab waveguide to produce a compact, high quality factor biosensor with a large internal surface area available for enhanced recognition of biological and chemical molecules. The porous nature of the ring resonator allows molecules to directly interact with the guided mode. Quality factors near 10,000 were measured for porous silicon ring resonators with a radius of 25 ?m. A bulk detection sensitivity of 380 nm/RIU was measured upon exposure to salt water solutions. Specific detection of nucleic acid molecules was demonstrated with a surface detection sensitivity of 4 pm/nM.

  4. High-resolution imaging of compact high-velocity clouds

    E-Print Network [OSTI]

    Robert Braun; Butler Burton

    1999-12-20T23:59:59.000Z

    Six examples of the compact, isolated high-velocity HI clouds (CHVCs) identified by Braun and Burton (1999) have been imaged with the WSRT. The 65 confirmed objects in this class define a dynamically cold system, with a global minimum for the velocity dispersion of only 70 km/s, found in the Local Group Standard of Rest, while in-falling at 100 km/s toward the LG barycenter. These objects have a characteristic morphology, in which several compact cores are embedded in a diffuse halo. The compact cores typically account for 40% of the HI line flux while covering some 15% of the source area. The cores are the cool condensed phase of HI, the CNM, with temp. near 100 K, while the halos appear to be a shielding column of warm diffuse HI, the WNM, with temp. near 8000 K. We detect a core with one of the narrowest HI emission lines ever observed, with intrinsic FWHM of 2 km/s and 75 K brightness. From a comparison of column and volume densities we derive a distance in the range 0.5 to 1 Mpc. We determine a metallicity for this same object of 0.04 to 0.07 solar. Comparably high distances are implied by demanding the stability of objects with multiple cores, which show relative velocities as large as 70 km/s on 30 arcmin scales. Many compact cores show systematic velocity gradients along the major axis of their elliptical extent which are consistent with circular rotation. Several of the derived rotation curves are well-fit by Navarro, Frenk, and White (1997) cold dark matter profiles. These kinematic signatures imply a high dark-to-visible mass ratio of 10-50, for D=0.7Mpc, which scales as 1/D. The implied dark matter halos dominate the mass volume density within the central 2 kpc (10 arcmin) of each source, providing a sufficent hydrostatic pressure to allow local CNM condensation. (abridged)

  5. Diffusion Welding of Compact Heat Exchangers for Nuclear Applications

    SciTech Connect (OSTI)

    Denis Clark; Ron Mizia; Dr. Michael V. Glazoff; Mr. Michael W. Patterson

    2012-06-01T23:59:59.000Z

    The next-­-generation nuclear plant (NGNP) is designed to be a flexible source of energy, producing various mixes of electrical energy and process heat (for example, for hydrogen generation) on demand. Compact heat exchangers provide an attractive way to move energy from the helium primary reactor coolant to process heat uses. For process heat efficiency, reactor outlet temperatures of 750-­-900°C are desirable. There are minor but deleterious components in the primary coolant; the number of alloys that can handle this environment is small. The present work concentrates on Alloys 800H and 617.

  6. PDC (polycrystalline diamond compact) bit research at Sandia National Laboratories

    SciTech Connect (OSTI)

    Finger, J.T.; Glowka, D.A.

    1989-06-01T23:59:59.000Z

    From the beginning of the geothermal development program, Sandia has performed and supported research into polycrystalline diamond compact (PDC) bits. These bits are attractive because they are intrinsically efficient in their cutting action (shearing, rather than crushing) and they have no moving parts (eliminating the problems of high-temperature lubricants, bearings, and seals.) This report is a summary description of the analytical and experimental work done by Sandia and our contractors. It describes analysis and laboratory tests of individual cutters and complete bits, as well as full-scale field tests of prototype and commercial bits. The report includes a bibliography of documents giving more detailed information on these topics. 26 refs.

  7. The nucleation of false vacuum bubbles with compact geometries

    E-Print Network [OSTI]

    Bum-Hoon Lee; Chul H. Lee; Wonwoo Lee; Changheon Oh

    2013-11-18T23:59:59.000Z

    We investigate the nucleation process for the possible types of vacuum bubbles. We classify false vacuum bubbles of a self-gravitating scalar field with compact geometries. We show that there exist numerical solutions representing the tunneling from the true vacuum state to the false vacuum state. The solutions are possible only gravity taken into account. We present the analytic computations for the radius and nucleation rate of a vacuum bubble using the thin-wall approximation. We discuss possible cosmological implications of our solutions.

  8. Compact cyclone filter train for radiological and hazardous environments

    DOE Patents [OSTI]

    Bench, Thomas R. (Pittsburgh, PA)

    1998-01-01T23:59:59.000Z

    A compact cyclone filter train for the removal of hazardous and radiologi particles from a gaseous fluid medium which permits a small cyclone separator to be used in a very small space envelope due to the arrangement of the filter housing adjacent to the separator with the cyclone separator and the filters mounted on a plate. The entire unit will have a hoist connection at the center of gravity so that the entire unit including the separator, the filters, and the base can be lifted and repositioned as desired.

  9. Controlled powder morphology experiments in megabar 304 stainless steel compaction

    SciTech Connect (OSTI)

    Staudhammer, K.P.; Johnson, K.A.

    1985-01-01T23:59:59.000Z

    Experiments with controlled morphology including shape, size, and size distribution were made on 304L stainless steel powders. These experiments involved not only the powder variables but pressure variables of 0.08 to 1.0 Mbar. Also included are measured container strain on the material ranging from 1.5% to 26%. Using a new strain controllable design it was possible to seperate and control, independently, strain and pressure. Results indicate that powder morphology, size distribution, packing density are among the pertinent parameters in predicting compaction of these powders.

  10. Compact Orthogonal NMR Field Sensor - Energy Innovation Portal

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645U.S. DOEThe Bonneville Power Administration would like submit the followingth Lomonosov1 COMMUNITYGeothermalCompact

  11. Compact high resolution isobar separator for study of exotic decays

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645U.S. DOEThe Bonneville Power Administration would like submit the followingth Lomonosov1Compact high resolution isobar

  12. Fluorescent Dye Encapsulated ZnO Particles with Cell-specific...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    the visible fluorescence emission of the dye or UV fluorescence emission of ZnO, and anti-cancerantibacterial treatments using the selective toxicity of the nanoscale ZnO outer...

  13. Classification with Artificial Neural Networks and Support Vector Machines: application to oil fluorescence spectra

    E-Print Network [OSTI]

    Oldenburg, Carl von Ossietzky Universität

    methods to examine crude oils, heavy refined oils, and sludge oils: the channels relationships method (CRMClassification with Artificial Neural Networks and Support Vector Machines: application to oil, and Oil fluorescence ABSTRACT: This paper reports on oil classification with fluorescence spectroscopy

  14. Detection of Ethylene Gas by Fluorescence Turn-On of a Conjugated Polymer

    E-Print Network [OSTI]

    Swager, Timothy Manning

    Ripe fruits: The fluorescence of a conjugated polymer is quenched by the presence of copper(I) moieties. Upon exposure to ethylene gas the copper complexes bind to ethylene and no longer quench the polymer fluorescence ...

  15. Extending the utility of enzymes for site-specific targeting of fluorescent probes

    E-Print Network [OSTI]

    Liu, Daniel S. (Daniel Shao-Chen)

    2014-01-01T23:59:59.000Z

    Genetically encodable fluorescence reporters such as the green fluorescent protein (GFP) are useful for studying protein expression, localization, and dynamics in a variety of biological systems. GFP and its related variants, ...

  16. Surfactant Diffusion into Lysozyme Crystal Matrices Investigated by Quantitative Fluorescence Microscopy

    E-Print Network [OSTI]

    Velev, Orlin D.

    the infusion of lysozyme crystals with pyrene-based fluorescent surfactants by quantitative fluorescence × 10-10 to 30 × 10-10 cm2 /s, depending on the type and size of the surfactant. The slow infusion

  17. Optical gating of perylene bisimide fluorescence using dithienylcyclopentene photochromic switches

    SciTech Connect (OSTI)

    Pärs, Martti; Köhler, Jürgen, E-mail: juergen.koehler@uni-bayreuth.de [Experimental Physics IV, University of Bayreuth, 95440 Bayreuth (Germany)] [Experimental Physics IV, University of Bayreuth, 95440 Bayreuth (Germany); Gräf, Katja; Bauer, Peter; Thelakkat, Mukundan [Applied Functional Polymers, University of Bayreuth, 95440 Bayreuth (Germany)] [Applied Functional Polymers, University of Bayreuth, 95440 Bayreuth (Germany)

    2013-11-25T23:59:59.000Z

    The emission of millions of fluorescence photons from a chromophore is controlled by the absorption of a few tens of photons in a photochromic molecule. The parameters that determine the efficiency of this process are investigated, providing insights for the development of an all-optical gate.

  18. EMERGING TECHNOLOGIES Two-photon excitation chlorophyll fluorescence lifetime imaging

    E-Print Network [OSTI]

    Qu, Jianan

    at higher Cd concentration was clearly identified. The decay of chlorophyll fluorescence extracted from) toxicity Abbreviations Cd Cadmium PS Photosystem LHCII Light-harvesting complex II PAM Pulse and Computer Engineering, Hong Kong University of Science and Technology (HKUST), Clear Water Bay, Kowloon

  19. Fluorescent lamp with static magnetic field generating means

    DOE Patents [OSTI]

    Moskowitz, P.E.; Maya, J.

    1987-09-08T23:59:59.000Z

    A fluorescent lamp wherein magnetic field generating means (e.g., permanent magnets) are utilized to generate a static magnetic field across the respective electrode structures of the lamp such that maximum field strength is located at the electrode's filament. An increase in efficacy during operation has been observed. 2 figs.

  20. Diffusion of Polymer-Coated Nanoparticles Studied by Fluorescence Correlation

    E-Print Network [OSTI]

    Granick, Steve

    Diffusion of Polymer-Coated Nanoparticles Studied by Fluorescence Correlation Spectroscopy Jiang of Brownian motion of polystyrene nanoparticles is controlled by tuning their hydro- dynamic radius through coefficient of the particles. This study has initiated our further studies on the interaction of nanoparticles

  1. Aqueous Ferrofluid of Magnetite Nanoparticles: Fluorescence Labeling and Magnetophoretic Control

    E-Print Network [OSTI]

    Swihart, Mark T.

    functionalization of magnetite nanoparticles using citric acid to produce a stable aqueous dispersionAqueous Ferrofluid of Magnetite Nanoparticles: Fluorescence Labeling and Magnetophoretic ControlVed: October 8, 2004 A method is presented for the preparation of a biocompatible ferrofluid containing dye-functionalized

  2. Classification of Protein Localization Patterns Obtained via Fluorescence Light Microscopy

    E-Print Network [OSTI]

    Gordon, Geoffrey J.

    of the microscope. They should also be in- sensitive to the wide variability in cell morphology that is present in fluores- cence light microscope images of mammalian cells. Such images are generated on a regular basis by labeling one or more subcellular structures with fluorescent dyes and then collecting images

  3. Cellubrevin-targeted Fluorescence Uncovers Heterogeneity in the Recycling Endosomes*

    E-Print Network [OSTI]

    Machen, Terry E.

    Cellubrevin-targeted Fluorescence Uncovers Heterogeneity in the Recycling Endosomes* (Received, University of California, Berkeley, California 94720-3200 The pH and trafficking of recycling endosomes have-enriched recycling endosomes (pHCb) and FITC-transferrin to measure the pH of transferrin- enriched recycling

  4. Enhanced Archaerhodopsin Fluorescent Protein Voltage Yiyang Gong1,2*

    E-Print Network [OSTI]

    Ferrari, Silvia

    Enhanced Archaerhodopsin Fluorescent Protein Voltage Indicators Yiyang Gong1,2* , Jin Zhong Li1 by nearly three-fold in comparison to Arch-D95N. Citation: Gong Y, Li JZ, Schnitzer MJ (2013) Enhanced; Published June 19, 2013 Copyright: © 2013 Gong et al. This is an open-access article distributed under

  5. Identication of Major Water-Soluble Fluorescent Components of Some

    E-Print Network [OSTI]

    Myrick, Michael Lenn

    limits for PAHs in water are in the parts-per-billion to parts-per- trillion range for a varietyIdenti®cation of Major Water-Soluble Fluorescent Components of Some Petrochemicals M. GRONER, A. R the ultraviolet (UV) ¯uorescence of water after exposure to gasoline, diesel fuel and crude oil are pre- sented

  6. Automatically Identifying Scatter in Fluorescence Data using Robust Techniques.

    E-Print Network [OSTI]

    (PARAFAC) to fluorescence excitation-emission data (EEM). The scatter does not contain any relevant handle first and second order Rayleigh scatter as well as Raman scatter in various types of EEM data of such a measurement is an excitation-emission matrix (EEM). When several samples (I) are mea- sured the data can

  7. Laser fluorescence EEM probe for cone penetrometer pollution analysis

    SciTech Connect (OSTI)

    Lin, J.; Hart, S.J.; Taylor, T.A.; Kenny, J.E. [Tufts Univ., Medford, MA (United States). Dept. of Chemistry

    1995-12-31T23:59:59.000Z

    A laser-induced fluorescence (LIF) excitation-emission matrix (EEM) probe has been developed in the laboratory, and installed and tested in a cone penetrometer. The laser excitation system uses the fourth harmonic of a flashlamp-pumped Nd:YAG laser (at 266 nm) to pump a Raman shifter. Up to ten laser beams (in the wavelength region of 257 to 400 nm) from the Raman shifter are launched into optical fibers that are connected to the optical fibers of the cone penetrometer probe through standard connectors. In the probe head, the laser radiation is focused onto the outer surface of sapphire windows that are in contact with the soils. The fluorescence emission is collected by ten collection fibers that take the fluorescence to a detection system consisting of a spectrograph and a CCD detector. This probe allows real-time collection of LIF-EEMs of pollutants adsorbed on solids or dissolved in groundwater. LIF-EEMs provide a substantial amount of spectral information that can be used to determine the composition and quantity of pollutants in soils. This probe can be used to measure POL (petroleum, oil, lubricants), PAH (polycyclic aromatic hydrocarbons), and other fluorescent pollutants. The LIF-EEM instrument has been developed in the laboratory, and installed in a cone penetrometer truck for a field test at Hill Air Force Base, Utah. The experience of the test will be discussed.

  8. Optimal resolution in Fresnel incoherent correlation holographic fluorescence microscopy

    E-Print Network [OSTI]

    Rosen, Joseph

    Optimal resolution in Fresnel incoherent correlation holographic fluorescence microscopy Gary, Israel 4 rosen@ee.bgu.ac.il *gbrooker@jhu.edu Abstract: Fresnel Incoherent Correlation Holography (FINCH. Rosen and G. Brooker, "Digital spatially incoherent Fresnel holography," Opt. Lett. 32(8), 912­914 (2007

  9. Amplifying Fluorescent Polymers Direct Synthesis of an OligonucleotidePoly-

    E-Print Network [OSTI]

    Tan, Weihong

    Amplifying Fluorescent Polymers Direct Synthesis of an Oligonucleotide­Poly- (phenylene ethynylene bioprobes can be constructed with these polymers for selective target recog- nition. To achieve this objective, the polymer must be conjugated with a biomolecule such as a DNA strand, a peptide, or a protein

  10. Automated hybridization/imaging device for fluorescent multiplex DNA sequencing

    DOE Patents [OSTI]

    Weiss, R.B.; Kimball, A.W.; Gesteland, R.F.; Ferguson, F.M.; Dunn, D.M.; Di Sera, L.J.; Cherry, J.L.

    1995-11-28T23:59:59.000Z

    A method is disclosed for automated multiplex sequencing of DNA with an integrated automated imaging hybridization chamber system. This system comprises an hybridization chamber device for mounting a membrane containing size-fractionated multiplex sequencing reaction products, apparatus for fluid delivery to the chamber device, imaging apparatus for light delivery to the membrane and image recording of fluorescence emanating from the membrane while in the chamber device, and programmable controller apparatus for controlling operation of the system. The multiplex reaction products are hybridized with a probe, the enzyme (such as alkaline phosphatase) is bound to a binding moiety on the probe, and a fluorogenic substrate (such as a benzothiazole derivative) is introduced into the chamber device by the fluid delivery apparatus. The enzyme converts the fluorogenic substrate into a fluorescent product which, when illuminated in the chamber device with a beam of light from the imaging apparatus, excites fluorescence of the fluorescent product to produce a pattern of hybridization. The pattern of hybridization is imaged by a CCD camera component of the imaging apparatus to obtain a series of digital signals. These signals are converted by the controller apparatus into a string of nucleotides corresponding to the nucleotide sequence an automated sequence reader. The method and apparatus are also applicable to other membrane-based applications such as colony and plaque hybridization and Southern, Northern, and Western blots. 9 figs.

  11. Automated hybridization/imaging device for fluorescent multiplex DNA sequencing

    DOE Patents [OSTI]

    Weiss, Robert B. (Salt Lake City, UT); Kimball, Alvin W. (Salt Lake City, UT); Gesteland, Raymond F. (Salt Lake City, UT); Ferguson, F. Mark (Salt Lake City, UT); Dunn, Diane M. (West Valley City, UT); Di Sera, Leonard J. (Salt Lake City, UT); Cherry, Joshua L. (Salt Lake City, UT)

    1995-01-01T23:59:59.000Z

    A method is disclosed for automated multiplex sequencing of DNA with an integrated automated imaging hybridization chamber system. This system comprises an hybridization chamber device for mounting a membrane containing size-fractionated multiplex sequencing reaction products, apparatus for fluid delivery to the chamber device, imaging apparatus for light delivery to the membrane and image recording of fluorescence emanating from the membrane while in the chamber device, and programmable controller apparatus for controlling operation of the system. The multiplex reaction products are hybridized with a probe, then an enzyme (such as alkaline phosphatase) is bound to a binding moiety on the probe, and a fluorogenic substrate (such as a benzothiazole derivative) is introduced into the chamber device by the fluid delivery apparatus. The enzyme converts the fluorogenic substrate into a fluorescent product which, when illuminated in the chamber device with a beam of light from the imaging apparatus, excites fluorescence of the fluorescent product to produce a pattern of hybridization. The pattern of hybridization is imaged by a CCD camera component of the imaging apparatus to obtain a series of digital signals. These signals are converted by the controller apparatus into a string of nucleotides corresponding to the nucleotide sequence an automated sequence reader. The method and apparatus are also applicable to other membrane-based applications such as colony and plaque hybridization and Southern, Northern, and Western blots.

  12. REGULAR PAPER Modulation of the fluorescence yield in heliobacterial cells

    E-Print Network [OSTI]

    . They are thought to use a light-driven cyclic electron transport pathway to pump protons, and thereby phos brief flashes is inversely correlated to the variable fluorescence. Using pump-probe spectros- copy), or conversion to heat. When photosynthetic systems are operating efficiently, photochemistry dominates

  13. Assaying protein import into mitochondria using fluorescence spectroscopy

    E-Print Network [OSTI]

    Cargill, Holly Beth

    2006-08-16T23:59:59.000Z

    of the Outer Membrane (TOM) complex, and the inner mitochondrial membrane (IM) via the Translocase of the Inner Membrane 23 (TIM23) complex. A novel system was set up to examine the import of matrix-targeted preproteins into mitochondria using fluorescence...

  14. Quantitative high dynamic range beam profiling for fluorescence microscopy

    SciTech Connect (OSTI)

    Mitchell, T. J., E-mail: t.j.mitchell@dur.ac.uk; Saunter, C. D.; O’Nions, W.; Girkin, J. M.; Love, G. D. [Centre for Advanced Instrumentation and Biophysical Sciences Institute, Department of Physics, Durham University, Durham DH1 3LE (United Kingdom)

    2014-10-15T23:59:59.000Z

    Modern developmental biology relies on optically sectioning fluorescence microscope techniques to produce non-destructive in vivo images of developing specimens at high resolution in three dimensions. As optimal performance of these techniques is reliant on the three-dimensional (3D) intensity profile of the illumination employed, the ability to directly record and analyze these profiles is of great use to the fluorescence microscopist or instrument builder. Though excitation beam profiles can be measured indirectly using a sample of fluorescent beads and recording the emission along the microscope detection path, we demonstrate an alternative approach where a miniature camera sensor is used directly within the illumination beam. Measurements taken using our approach are solely concerned with the illumination optics as the detection optics are not involved. We present a miniature beam profiling device and high dynamic range flux reconstruction algorithm that together are capable of accurately reproducing quantitative 3D flux maps over a large focal volume. Performance of this beam profiling system is verified within an optical test bench and demonstrated for fluorescence microscopy by profiling the low NA illumination beam of a single plane illumination microscope. The generality and success of this approach showcases a widely flexible beam amplitude diagnostic tool for use within the life sciences.

  15. Global VLBI Observations of Compact Radio Sources in M82

    E-Print Network [OSTI]

    A. R. McDonald; T. W. B. Muxlow; A. Pedlar; M. A. Garrett; K. A. Wills; S. T. Garrington; P. J. Diamond; P. N. Wilkinson

    2000-10-23T23:59:59.000Z

    Observations of the starburst galaxy, M82, have been made with a 20-station global VLBI array at $\\lambda$18cm. Maps are presented of the brightest young supernova remnants (SNR) in M82 and the wide-field mapping techniques used in making images over a field of view of $\\sim$1 arcminute with 3 milliarcsecond resolution are discussed. A limit has been placed on the power law deceleration of the young SNR, 43.31+592 with an index greater than 0.73 $\\pm$ 0.11 from observations with the European VLBI Network. Using the global array we have resolved compact knots of radio emission in the source which, with future global observations, will enable better constraints to be placed on the expansion parameters of this SNR. The latest global observations have also provided high resolution images of the most compact radio source in M82, 41.95+575. We determine an upper limit to the radial expansion rate along the major axis of 2000 km s$^{-1}$. However, the new images also show structure resembling that of collimated ejection which brings into question the previous explanation of the source as being due to the confinement of a supernova by a high density circumstellar medium. It is apparent that we are now able to image the brightest supernova remnants in M82 with a linear scale which allows direct comparison with galactic SNR such as Cassiopeia A.

  16. The effects of compaction of different golf green soil mixtures on plant growth

    E-Print Network [OSTI]

    Kunze, Raymond John

    1956-01-01T23:59:59.000Z

    growth, removed prior Co compaction treatments, from mixtures of different sand- clay soll-peat rstlosoeoooeoo ~ ~ aeoaoae ~ o oo ~ o ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ 7e An average of 2 clipping yields of top growth, removed after Che compaction and during...-clay soil-peat rs'tlos ~ a ~ eaoaoaeooaeeaa ~ o ~ aeea e ~ o ~ eaeoao ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ a ~ aooo 28 9e Differential effects of the different sand-clay soll-peat ratios of 5 particle size mixtures on yields of 2 clip plugs following Che compaction...

  17. Detection of counterfeit U.S. paper money using intrinsic fluorescence lifetime

    E-Print Network [OSTI]

    Levene, Michael J.

    -photon spectral and lifetime fluorescence microscopy," Appl. Opt. 43(27), 5173­5182 (2004). #118121 - $15.00 USD

  18. Damage to HDPE geomembrane from interface shear over gravelly compacted clay liner

    E-Print Network [OSTI]

    Thielmann, Stuart

    2012-01-01T23:59:59.000Z

    hydraulic conductivity of compacted clay liners,” Journal offrom stones in an underlying clay layer,” Geotextiles andof three geosynthetic clay liners,” Journal of Geotechnical

  19. Nuclear fuel particles and method of making nuclear fuel compacts therefrom

    DOE Patents [OSTI]

    DeVelasco, Rubin I. (Encinitas, CA); Adams, Charles C. (San Diego, CA)

    1991-01-01T23:59:59.000Z

    Methods for making nuclear fuel compacts exhibiting low heavy metal contamination and fewer defective coatings following compact fabrication from a mixture of hardenable binder, such as petroleum pitch, and nuclear fuel particles having multiple layer fission-product-retentive coatings, with the dense outermost layer of the fission-product-retentive coating being surrounded by a protective overcoating, e.g., pyrocarbon having a density between about 1 and 1.3 g/cm.sup.3. Such particles can be pre-compacted in molds under relatively high pressures and then combined with a fluid binder which is ultimately carbonized to produce carbonaceous nuclear fuel compacts having relatively high fuel loadings.

  20. Bulk superhard B-C-N nanocomposite compact and method for preparing thereof

    DOE Patents [OSTI]

    Zhao, Yusheng; He, Duanwei

    2004-07-06T23:59:59.000Z

    Bulk, superhard, B-C-N nanocomposite compact and method for preparing thereof. The bulk, superhard, nanocomposite compact is a well-sintered compact and includes nanocrystalline grains of at least one high-pressure phase of B-C-N surrounded by amorphous diamond-like carbon grain boundaries. The bulk compact has a Vicker's hardness of about 41-68 GPa. It is prepared by ball milling a mixture of graphite and hexagonal boron nitride, encapsulating the ball-milled mixture, and sintering the encapsulated ball-milled mixture at a pressure of about 5-25 GPa and at a temperature of about 1000-2500 K.

  1. Diffusion and Swelling Measurements in Pharmaceutical Powder Compacts Using Terahertz Pulsed Imaging

    E-Print Network [OSTI]

    Yassin, Samy; Su, Ke; Lin, Hungyen; Gladden, Lynn F.; Zeitler, J. Axel

    2015-02-02T23:59:59.000Z

    the Morphologi v8.11 software (Malvern In- struments). The mean particle size, D50, of HPMC, Eudragit RSPO, and Lactose were 16.9, 8.6, and 22.1 :m, respectively. Compaction Tablets were compressed to 1.5 mm thickness, either by using a manual hydraulic press... - prisingly, the tablets produced using the compaction simulator exhibited a more consistent pore distribution compared with the ones produced using the hydraulic press that reflects the more controlled method of compaction in the compaction simu- lator...

  2. Global compactness for a class of quasi-linear elliptic problems

    E-Print Network [OSTI]

    Mercuri, Carlo

    2011-01-01T23:59:59.000Z

    We prove a global compactness result for Palais-Smale sequences associated with a class of quasi-linear elliptic equations on exterior domains.

  3. Compact, Light-Weight, Single-Phase, Liquid-Cooled Cold Plate...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    1 DOE Hydrogen and Fuel Cells Program, and Vehicle Technologies Program Annual Merit Review and Peer Evaluation ape039narumanchi2011p.pdf More Documents & Publications Compact,...

  4. A Superconducting Bending Magnet System for a Compact Synchrotron Light Source

    E-Print Network [OSTI]

    Green, M.A.

    2011-01-01T23:59:59.000Z

    Garren, "Optimization of Superconducting Bending Magnets foral, "Development of a Superconducting Compact Storage Ringsdesigns M. A Green, "Superconducting Dipole Magnets for

  5. Cape Light Compact- Commercial, Industrial and Municipal Buildings Energy Efficiency Rebate Program

    Broader source: Energy.gov [DOE]

    Through a multi-member partnership, Cape Light Compact (CLC) and Masssave offer a variety of financial incentives for commercial, industrial, and municipal facilities. Custom rebate options are...

  6. Caged Molecular Fluorescence Velocimetry to measure meso-to micro-scale thermal flow fields

    E-Print Network [OSTI]

    Park, Jaesung

    2000-01-01T23:59:59.000Z

    (CPL). The system utilizes a microscope objective lens, caged molecular fluorescence probes, Nd:YAG laser for UV light source, Ar-ion laser for 488 nm fluorescence pumping, and a color CCD camera to record a series of fluorescent images. Caged...

  7. 428 BIOCHIMICAET BIOPHYSICAACTA pH CONTROL OF THE CHLOROPHYLL a FLUORESCENCE IN ALGAE

    E-Print Network [OSTI]

    Govindjee

    428 BIOCHIMICAET BIOPHYSICAACTA BBA 46126 pH CONTROL OF THE CHLOROPHYLL a FLUORESCENCE IN ALGAE on the "slow" (min) time course of Chlorophyll a fluorescence yield in the green alga Chlorella pyrenoidosa and in the blue-green alga Anacystis nidulans. In Chlorella, the decay of fluorescence yield, in the I- to 5-rain

  8. Fluorescence Behavioral Imaging (FBI) Tracks Identity in Heterogeneous Groups of Drosophila

    E-Print Network [OSTI]

    Floreano, Dario

    Fluorescence Behavioral Imaging (FBI) Tracks Identity in Heterogeneous Groups of Drosophila Pavan describe Fluorescence Behavioral Imaging (FBI), a toolkit that uses transgenic fluorescence to discriminate-source software for automated, high-accuracy determination of genetic identity. Using FBI, we measure courtship

  9. Fluorescence quenching of water-soluble porphyrins. A novel fluorescence quenching of anionic porphyrin by anionic anthraquinone

    SciTech Connect (OSTI)

    Kano, K.; Sato, T.; Yamada, S.; Ogawa, T.

    1983-02-17T23:59:59.000Z

    The fluorescence quenching of 5-phenyl-10,15,20-tris(p-sulfonatophenyl)porphine (TPPS/sup 3 -/) and 5,10,15,20-tetrakis(4-N-methylpyridyl)porphine (TMPyP/sup 4 +/) has been studied in water (pH 8.0) by using 9,10-anthra-quinone-2,6-disulfonate (AQDS/sup 2 -/) and methyl viologen (MV/sup 2 +/) as quenchers. While electrostatic repulsion is expected, AQDS/sup 2 -/ quenched the TPPS/sup 3 -/ fluorescence more efficiently than MV/sup 2 +/. The steady-state and time-resolved fluorescence measurements indicated that static quenching took place in the TPPS/sup 3 -/-AQDS/sup 2 -/ system. Studies on the absorption spectra and the effects of ionic strength on the fluorescence quenching indicated the formation of the ground-state complex of TPPS/sup 3 -/ and AQDS/sup 2 -/. The thermodynamic parameters (..delta..H and ..delta..S) suggested that the ground-state complex was formed via van der Walls interaction.

  10. Fluorescent Probe Solubilization in the Headgroup and Core Regions of Micelles: Fluorescence Lifetime and Orientational Relaxation Measurements

    E-Print Network [OSTI]

    Fayer, Michael D.

    the microheterogeneous medium under investigation. To ascertain that the probe is located in the target environment in the hydrocarbon core region of the micelle. In this environment the chromophores have a considerably longer to be applied successfully, the fluorescent molecule must be tailored to probe the desired environment within

  11. Compact cladding-pumped planar waveguide amplifier and fabrication method

    DOE Patents [OSTI]

    Bayramian, Andy J.; Beach, Raymond J.; Honea, Eric; Murray, James E.; Payne, Stephen A.

    2003-10-28T23:59:59.000Z

    A low-cost, high performance cladding-pumped planar waveguide amplifier and fabrication method, for deployment in metro and access networks. The waveguide amplifier has a compact monolithic slab architecture preferably formed by first sandwich bonding an erbium-doped core glass slab between two cladding glass slabs to form a multi-layer planar construction, and then slicing the construction into multiple unit constructions. Using lithographic techniques, a silver stripe is deposited and formed at a top or bottom surface of each unit construction and over a cross section of the bonds. By heating the unit construction in an oven and applying an electric field, the silver stripe is then ion diffused to increase the refractive indices of the core and cladding regions, with the diffusion region of the core forming a single mode waveguide, and the silver diffusion cladding region forming a second larger waveguide amenable to cladding pumping with broad area diodes.

  12. Color Superconductivity in Compact Stars and Gamma Ray Bursts

    E-Print Network [OSTI]

    A. Drago; A. Lavagno; G. Pagliara

    2003-04-08T23:59:59.000Z

    We study the effects of color superconductivity on the structure and formation of compact stars. We show that it is possible to satisfy most of recent observational boundaries on masses and radii if a diquark condensate forms in a hybrid or a quark star. Moreover, we find that a huge amount of energy, of the order of $10^{53}$ erg, can be released in the conversion from a (metastable) hadronic star into a (stable) hybrid or quark star, if the presence of a color superconducting phase is taken into account. Accordingly to the scenario proposed in Astrophys.J.586(2003)1250, the energy released in this conversion can power a Gamma Ray Burst. This mechanism can explain the recent observations indicating a delay, of the order of days or years, between a few Supernova explosions and the subsequent Gamma Ray Burst.

  13. Compact High-Velocity Clouds at High Resolution

    E-Print Network [OSTI]

    W. B. Burton; Robert Braun

    1999-12-22T23:59:59.000Z

    Six examples of the compact, isolated high-velocity clouds catalogued by Braun & Burton (1999) and identified with a dynamically cold ensemble of primitive objects falling towards the barycenter of the Local Group have been imaged with the Westerbork Synthesis Radio Telescope; an additional ten have been imaged with the Arecibo telescope. The imaging reveals a characteristic core/halo morphology: one or several cores of cool, relatively high-column-density material, are embedded in an extended halo of warmer, lower-density material. Several of the cores show kinematic gradients consistent with rotation; these CHVCs are evidently rotationally supported and dark-matter dominated. The imaging data allows several independent estimates of the distances to these objects, which lie in the range 0.3 to 1.0 Mpc. The CHVC properties resemble what might be expected from very dark dwarf irregular galaxies.

  14. Compact, maintainable 80-KeV neutral beam module

    DOE Patents [OSTI]

    Fink, Joel H. (Livermore, CA); Molvik, Arthur W. (Livermore, CA)

    1980-01-01T23:59:59.000Z

    A compact, maintainable 80-keV arc chamber, extractor module for a neutral beam system immersed in a vacuum of <10.sup.-2 Torr, incorporating a nested 60-keV gradient shield located midway between the high voltage ion source and surrounding grounded frame. The shield reduces breakdown or arcing path length without increasing the voltage gradient, tends to keep electric fields normal to conducting surfaces rather than skewed and reduces the peak electric field around irregularities on the 80-keV electrodes. The arc chamber or ion source is mounted separately from the extractor or ion accelerator to reduce misalignment of the accelerator and to permit separate maintenance to be performed on these systems. The separate mounting of the ion source provides for maintaining same without removing the ion accelerator.

  15. Evidence for compact structuring in the corona of active stars

    E-Print Network [OSTI]

    F. Favata

    2000-11-27T23:59:59.000Z

    The ``current wisdom'' regarding the structuring of the X-ray emitting corona in active stars (i.e. a corona dominated by extended coronal structures) is briefly reviewed, followed by a review of a new approach to flare analysis and the analysis of a significant number of newly observed and previously published large flares, all leading to a much more compactly structured corona. Recent observations showing the polar location of the flaring plasma are then discussed, showing how the current evidence points toward a (flaring) corona composed of rather low-lying polar structures, also in agreement with some recent radio VLBI observational results and with starspot Doppler images. The resulting picture is significantly different from the solar case.

  16. Compact mass spectrometer for plasma discharge ion analysis

    DOE Patents [OSTI]

    Tuszewski, Michel G. (Los Alamos, NM)

    1997-01-01T23:59:59.000Z

    A mass spectrometer and methods for mass spectrometry which are useful in characterizing a plasma. This mass spectrometer for determining type and quantity of ions present in a plasma is simple, compact, and inexpensive. It accomplishes mass analysis in a single step, rather than the usual two-step process comprised of ion extraction followed by mass filtering. Ions are captured by a measuring element placed in a plasma and accelerated by a known applied voltage. Captured ions are bent into near-circular orbits by a magnetic field such that they strike a collector, producing an electric current. Ion orbits vary with applied voltage and proton mass ratio of the ions, so that ion species may be identified. Current flow provides an indication of quantity of ions striking the collector.

  17. Beam shaping element for compact fiber injection systems

    SciTech Connect (OSTI)

    Weichman, L.S.; Dickey, F.M.; Shagam, R.N.

    2000-01-05T23:59:59.000Z

    Injection of high power, multi-mode laser profiles into a fiber optic delivery system requires controlling a number of injection parameters to maximize throughput and minimize concerns for optical damage both at the entrance and exit faces of the fiber optic. A simple method for simultaneously achieving a compact fiber injection geometry and control of these injection parameters, independent of the input source characteristics, is provided by a refractive lenslet array and simple injection lens configuration. Design criteria together with analytical and experimental results for the refractive lenslet array and short focal length injection lens are presented. This arrangement provides a uniform spatial intensity distribution at the fiber injection plane to a large degree independent of the source mode structure, spatial profile, divergence, size, and/or alignment to the injection system. This technique has application to a number of laser systems where uniform illumination of a target or remote delivery of high peak power is desired.

  18. Collisional Hardening of Compact Binaries in Globular Clusters

    E-Print Network [OSTI]

    S. Banerjee; P. Ghosh

    2006-09-29T23:59:59.000Z

    We consider essential mechanisms for orbit-shrinkage or "hardening" of compact binaries in globular clusters to the point of Roche-lobe contact and X-ray emission phase, focussing on the process of collisional hardening due to encounters between binaries and single stars in the cluster core. The interplay between this kind of hardening and that due to emission of gravitational radiation produces a characteristic scaling of the orbit-shrinkage time with the single-star binary encounter rate $\\gamma$ in the cluster which we introduce, clarify, and explore. We investigate possible effects of this scaling on populations of X-ray binaries in globular clusters within the framework of a simple "toy" scheme for describing the evolution of pre-X-ray binaries in globular clusters. We find the expected qualitative trends sufficiently supported by data on X-ray binaries in galactic globular clusters to encourage us toward a more quantitative study.

  19. Phase conversion dissipation in multi-component compact stars

    E-Print Network [OSTI]

    Mark G. Alford; Sophia Han; Kai Schwenzer

    2015-01-15T23:59:59.000Z

    We propose a mechanism for the damping of density oscillations in multi-component compact stars. The mechanism is the periodic conversion between different phases, i.e. the movement of the interface between them, induced by pressure oscillations in the star. The damping grows nonlinearly with the amplitude of the oscillation. We study in detail the case of r-modes in a hybrid star with a sharp interface, and we find that this mechanism is powerful enough to saturate the r-mode at very low saturation amplitude, of order $10^{-10}$, and is therefore likely to be the dominant r-mode saturation mechanism in hybrid stars with a sharp interface.

  20. Measurements of Beam Ion Loss from the Compact Helical System

    SciTech Connect (OSTI)

    D. S. Darrow, M. Isobe, Takashi Kondo, M. Sasao, and the CHS Group National Institute for Fusion Science, Toki, Gifu, Japan

    2010-02-03T23:59:59.000Z

    Beam ion loss from the Compact Helical System (CHS) has been measured with a scintillator-type probe. The total loss to the probe, and the pitch angle and gyroradius distributions of that loss, have been measured as various plasma parameters were scanned. Three classes of beam ion loss were observed at the probe position: passing ions with pitch angles within 10o of those of transition orbits, ions on transition orbits, and ions on trapped orbits, typically 15o or more from transition orbits. Some orbit calculations in this geometry have been performed in order to understand the characteristics of the loss. Simulation of the detector signal based upon the following of orbits from realistic beam deposition profiles is not able to reproduce the pitch angle distribution of the losses measured. Consequently it is inferred that internal plasma processes, whether magnetohydrodynamic modes, radial electric fields, or plasma turbulence, move previously confined beam ions to transition orbits, resulting in their loss.

  1. Resurvey of order and chaos in spinning compact binaries

    SciTech Connect (OSTI)

    Wu Xin [Department of Physics, Nanchang University, Nanchang 330031 (China); Xie Yi [Department of Astronomy, Nanjing University, Nanjing 210093 (China)

    2008-05-15T23:59:59.000Z

    This paper is mainly devoted to applying the invariant, fast, Lyapunov indicator to clarify some doubt regarding the apparently conflicting results of chaos in spinning compact binaries at the second-order post-Newtonian approximation of general relativity from previous literatures. It is shown with a number of examples that no single physical parameter or initial condition can be described as responsible for causing chaos, but a complicated combination of all parameters and initial conditions is responsible. In other words, a universal rule for the dependence of chaos on each parameter or initial condition cannot be found in general. Chaos does not depend only on the mass ratio, and the maximal spins do not necessarily bring the strongest effect of chaos. Additionally, chaos does not always become drastic when the initial spin vectors are nearly perpendicular to the orbital plane, and the alignment of spins cannot trigger chaos by itself.

  2. Systems Analysis of a Compact Next Step Burning Plasma Experiment

    SciTech Connect (OSTI)

    S.C. Jardin; C.E. Kessel; D. Meade; C. Neumeyer

    2002-02-06T23:59:59.000Z

    A new burning plasma systems code (BPSC) has been developed for analysis of a next step compact burning plasma experiment with copper-alloy magnet technology. We consider two classes of configurations: Type A, with the toroidal field (TF) coils and ohmic heating (OH) coils unlinked, and Type B, with the TF and OH coils linked. We obtain curves of the minimizing major radius as a function of aspect ratio R(A) for each configuration type for typical parameters. These curves represent, to first order, cost minimizing curves, assuming that device cost is a function of major radius. The Type B curves always lie below the Type A curves for the same physics parameters, indicating that they lead to a more compact design. This follows from that fact that a high fraction of the inner region, r < R-a, contains electrical conductor material. However, the fact that the Type A OH and TF magnets are not linked presents fewer engineering challenges and should lead to a more reliable design. Both the Type A and Type B curves have a minimum in major radius R at a minimizing aspect ratio A typically above 2.8 and at high values of magnetic field B above 10 T. The minimizing A occurs at larger values for longer pulse and higher performance devices. The larger A and higher B design points also have the feature that the ratio of the discharge time to the current redistribution time is largest so that steady-state operation can be more realistically prototyped. A sensitivity study is presented for the baseline Type A configuration showing the dependence of the results on the parameters held fixed for the minimization study.

  3. Revisit on ''Ruling out chaos in compact binary systems''

    SciTech Connect (OSTI)

    Wu Xin [Department of Physics, Nanchang University, Nanchang 330031 (China); Xie Yi [Department of Astronomy, Nanjing University, Nanjing 210093 (China)

    2007-12-15T23:59:59.000Z

    Full general relativity requires that chaos indicators should be invariant in various spacetime coordinate systems for a given relativistic dynamical problem. On the basis of this point, we calculate the invariant Lyapunov exponents (LEs) for one of the spinning compact binaries in the conservative second post-Newtonian (2PN) Lagrangian formulation without the dissipative effects of gravitational radiation, using the two-nearby-orbits method with projection operations and with coordinate time as an independent variable. It is found that the actual source leading to zero LEs in one paper [J. D. Schnittman and F. A. Rasio, Phys. Rev. Lett. 87, 121101 (2001)] but to positive LEs in the other [N. J. Cornish and J. Levin, Phys. Rev. Lett. 89, 179001 (2002)] does not mainly depend on rescaling, but is due to two slightly different treatments of the LEs. It takes much more CPU time to obtain the stabilizing limit values as reliable values of LEs for the former than to get the slopes (equal to LEs) of the fit lines for the latter. Due to coalescence of some of the black holes, the LEs from the former are not an adaptive indicator of chaos for comparable mass compact binaries. In this case, the invariant fast Lyapunov indicator (FLI) of two-nearby orbits, as a very sensitive tool to distinguish chaos from order, is worth recommending. As a result, we do again find chaos in the 2PN approximation through different ratios of FLIs varying with time. Chaos cannot indeed be ruled out in real binaries.

  4. Nano-compact disks with 400 Gbit/in2 storage density fabricated

    E-Print Network [OSTI]

    Nano-compact disks with 400 Gbit/in2 storage density fabricated using nanoimprint lithography and read with proximal probe Peter R. Kraussa) and Stephen Y. Choub) NanoStructure Laboratory, Department for publication 30 September 1997 Nano-compact disks Nano-CDs with 400 Gbit/in2 topographical bit density nearly

  5. A Study of the Hydro-Mechanical Behaviour of Compacted Crushed Argillite

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    1 A Study of the Hydro-Mechanical Behaviour of Compacted Crushed Argillite C.S. Tang a, b , A and the microstruc- ture on the hydro-mechanical behaviour of the compacted crushed argillite have been in a strong effect of the grain size distribution on the hydro-mechanical behaviour and thus the close link

  6. Compact, High-Resolution, Multi-Layer Semiconductor PET Detector Module

    E-Print Network [OSTI]

    Ohta, Shigemi

    Compact, High-Resolution, Multi-Layer Semiconductor PET Detector Module Summary Multi tomography (PET) systems, but the conventional electrodes used require a prohibitive number of readout channels. Now, a breakthrough compact PET detector offers a specialized configuration of cross strip

  7. Flame Stability Analysis in an Ultra Compact Combustor Using Large-Eddy Simulation

    E-Print Network [OSTI]

    Raman, Venkat

    Flame Stability Analysis in an Ultra Compact Combustor Using Large-Eddy Simulation C. Lietz , C Base, Ohio 45433 Large eddy simulation (LES) of an experimental ultra-compact combustor (UCC as a conven- tional combustor path. In order to reduce the penalty due to increased weight of these burners

  8. A RELATIVE TRACE FORMULA FOR A COMPACT RIEMANN KIMBALL MARTIN, MARK MCKEE, AND ERIC WAMBACH

    E-Print Network [OSTI]

    Martin, Kimball

    A RELATIVE TRACE FORMULA FOR A COMPACT RIEMANN SURFACE KIMBALL MARTIN, MARK MCKEE, AND ERIC WAMBACH Abstract. We study a relative trace formula for a compact Riemann surface with respect to a closed geodesic estimates on the lengths of geodesic segments which start and end orthogonally on C. Variant trace formulas

  9. Disk-shaped Compact Tension Test for Plain Concrete A. Amirkhanian1

    E-Print Network [OSTI]

    Paulino, Glaucio H.

    Disk-shaped Compact Tension Test for Plain Concrete A. Amirkhanian1 , D. Spring1 , J. Roesler1 , K cracking prediction of concrete pavement systems. The single-edge notched beam test has been used energy in asphalt concrete using the disk-shaped compact tension (DCT) test. The benefit of this specimen

  10. The ARIES-CS A Compact Stellarator Power Plant F. Najmabadi

    E-Print Network [OSTI]

    Najmabadi, Farrokh

    1 FT/P5-26 The ARIES-CS ­ A Compact Stellarator Power Plant F. Najmabadi University of California features as fusion power plants. A detailed and integrated study of compact stellarator configurations as power plants, ARIES-CS, was initiated recently. Configurations with A 6 and excellent quasi

  11. Melt segregation under compaction and shear channelling: Application to granitic magma segregation in a continental crust

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    1 Melt segregation under compaction and shear channelling: Application to granitic magma segregation in a mush submitted to both compaction and shear. It applies to a granitic melt imbedded within of melt to about 20 % in total to be extracted from the matrix. Abridged title Granitic melt segregation

  12. Impact of Soil Type and Compaction Conditions on Soil Water Characteristic

    E-Print Network [OSTI]

    Yu, Sheng-Tao

    Impact of Soil Type and Compaction Conditions on Soil Water Characteristic C. J. Miller, M.ASCE1 the variation of water content and pore water suction for compacted clayey soils. The soils had varying amounts of clay fraction with plasticities ranging from low to high plasticity. The unsaturated soil behavior

  13. Soil compaction: track induced soil stress isn't so positive in comparison with tyre

    E-Print Network [OSTI]

    Boyer, Edmond

    Soil compaction: track induced soil stress isn't so positive in comparison with tyre Ingeniors, Clermont-Ferrand, France Abstract This study concludes that, from the soil compaction point of view, using on all the contact area and induce overall less stress on the soil. Introduction As agricultural machines

  14. The probabilistic powerdomain for stably compact spaces Mauricio AlvarezManilla # Achim Jung + Klaus Keimel #

    E-Print Network [OSTI]

    Jung, Achim

    on these spaces. This is the basis for transferring methods and results from functional analysis to the non of the (known) fact that every valuation on a stably compact space extends uniquely to a Radon measure on the Borel algebra of the corresponding compact Hausdorff space. The view of valuations and measures

  15. The probabilistic powerdomain for stably compact spaces Mauricio Alvarez-Manilla

    E-Print Network [OSTI]

    Jung, Achim

    . This is the basis for transferring methods and results from functional analysis to the non-Hausdorff setting that every valuation on a stably compact space extends uniquely to a Radon measure on the Borel algebra of the corresponding compact Hausdorff space. The view of valuations and measures as certain linear functionals

  16. ccsd-00001059(version1):26Jan2004 Continuous melting of compact polymers

    E-Print Network [OSTI]

    Boyer, Edmond

    ccsd-00001059(version1):26Jan2004 Continuous melting of compact polymers Jesper Lykke Jacobsen and bending rigidity in compact polymers can be ad- dressed within a lattice model introduced by P.J. Flory for polymers on surfaces, such as DNA adsorbed on a lipid bilayer. We predict a continuous melting transition

  17. Hierarchical Sequence Compaction for Power Estimation* Radu Marculescu, Diana Marculescu, Massoud Pedram

    E-Print Network [OSTI]

    Pedram, Massoud

    1 Hierarchical Sequence Compaction for Power Estimation* Radu Marculescu, Diana Marculescu, Massoud 90089 Abstract - This paper presents an effective technique for compacting a large sequence of input vectors into a much smaller one such that when the two sequences are applied to any circuit, the resulting

  18. Optimization of sequential attractor-based movement for compact behaviour generation

    E-Print Network [OSTI]

    Toussaint, Marc

    Optimization of sequential attractor-based movement for compact behaviour generation Marc Toussaint optimal robot motion based on a sequence of attractor dynamics in task space. This is motivated] ­ and by the need for compact movement representations on which efficient optimization can be performed. We

  19. THE FBI TRANSFORM ON COMPACT C 1 MANIFOLDS JARED WUNSCH AND MACIEJ ZWORSKI

    E-Print Network [OSTI]

    Zworski, Maciej

    THE FBI TRANSFORM ON COMPACT C 1 MANIFOLDS JARED WUNSCH AND MACIEJ ZWORSKI 1. Introduction In this paper we discuss the Fourier-Bros-Iagolnitzer (FBI) transform on smooth, boundaryless manifolds-compactness of the cotangent bundle. By reviewing the basic constructions of the FBI transform theory, we hope to make

  20. Gurson's plasticity coupled to damage as a CAP model for concrete compaction in dynamics

    E-Print Network [OSTI]

    1 Gurson's plasticity coupled to damage as a CAP model for concrete compaction in dynamics Fabrice (compaction) but also the plastic strains in compression and cracking in tension. Recently, new dynamic is generally described by means of the plasticity theory where the spherical and the deviatoric responses

  1. Coded Aperture Imaging for Fluorescent X-rays-Biomedical Applications

    SciTech Connect (OSTI)

    Haboub, Abdel; MacDowell, Alastair; Marchesini, Stefano; Parkinson, Dilworth

    2013-06-01T23:59:59.000Z

    Employing a coded aperture pattern in front of a charge couple device pixilated detector (CCD) allows for imaging of fluorescent x-rays (6-25KeV) being emitted from samples irradiated with x-rays. Coded apertures encode the angular direction of x-rays and allow for a large Numerical Aperture x- ray imaging system. The algorithm to develop the self-supported coded aperture pattern of the Non Two Holes Touching (NTHT) pattern was developed. The algorithms to reconstruct the x-ray image from the encoded pattern recorded were developed by means of modeling and confirmed by experiments. Samples were irradiated by monochromatic synchrotron x-ray radiation, and fluorescent x-rays from several different test metal samples were imaged through the newly developed coded aperture imaging system. By choice of the exciting energy the different metals were speciated.

  2. Fluorescence quenching of CdSe quantum dots on graphene

    SciTech Connect (OSTI)

    Guo, Xi Tao; Hua Ni, Zhen, E-mail: zhni@seu.edu.cn; Yan Nan, Hai; Hui Wang, Wen [Department of Physics and Key Laboratory of MEMS of the Ministry of Education, Southeast University, Nanjing 211189 (China)] [Department of Physics and Key Laboratory of MEMS of the Ministry of Education, Southeast University, Nanjing 211189 (China); Yan Liao, Chun [Physics Department, National Photoelectric Technology and Functional Materials and Application of Science and Technology International Cooperation Base, Northwest University, Xi'an 710069 (China)] [Physics Department, National Photoelectric Technology and Functional Materials and Application of Science and Technology International Cooperation Base, Northwest University, Xi'an 710069 (China); Zhang, Yan; Wei Zhao, Wei [Jiangsu Key Laboratory for Design and Fabrication of Micro-Nano Biomedical Instruments, School of Mechanical Engineering, Southeast University, Nanjing 211189 (China)] [Jiangsu Key Laboratory for Design and Fabrication of Micro-Nano Biomedical Instruments, School of Mechanical Engineering, Southeast University, Nanjing 211189 (China)

    2013-11-11T23:59:59.000Z

    We studied systematically the fluorescence quenching of CdSe quantum dots (QDs) on graphene and its multilayers, as well as graphene oxide (GO) and reduced graphene oxide (rGO). Raman intensity of QDs was used as a quantitatively measurement of its concentration in order to achieve a reliable quenching factor (QF). It was found that the QF of graphene (?13.1) and its multilayers is much larger than rGO (?4.4), while GO (?1.5) has the lowest quenching efficiency, which suggests that the graphitic structure is an important factor for quenching the fluorescence of QDs. It was also revealed that the QF of graphene is not strongly dependent on its thicknesses.

  3. Archaeometrical studies using X-ray fluorescence methods

    SciTech Connect (OSTI)

    Pauna, Catalina; Constantinescu, B.; Constantin, F.; Bugoi, R.; Stan, D.; Vasilescu, A. [National Institute of Nuclear Physics and Engineering, POB MG-6, 077125, Bucharest (Romania)

    2010-04-26T23:59:59.000Z

    Elemental analysis contributes to authentication (knowing the elemental composition and considering the information about the usual composition of the objects in different historical periods it can be established if the item is original or fake), provenance studies (minor and trace elements indicates ores origin and 'consequently' mines location), (relative) dating of archaeological objects (e.g. for painted items--the chemical recipes for pigments can offer information about the age of objects). The paper gives a general layout for the NIPNE Archaeometry Laboratory's applications using X-Ray Fluorescence (XRF), micro--Proton Induced X-Ray Emission (micro-PIXE), micro-Synchrotron Radiation Induced X-Ray Fluorescence (micro--SR-XRF) methods.

  4. Noise induced narrowing of metamolecule fluorescence spectral line

    E-Print Network [OSTI]

    E. S. Andrianov; N. M. Chtchelkatchev; A. A. Pukhov

    2015-04-27T23:59:59.000Z

    We consider metamolecule consisting of bosonic mode correlated with the two-level system: it can be, for example, plasmonic mode interacting with the quantum dot or molecule in the resonator. We focus on the parameter range where all the correlations are strong and of the same order: interaction between bosonic mode correlated with the two-level system, external coherent drive and dissipation. Quantum Monte-Carlo simulations show a fluorescence of this system at dissipation larger than the driving amplitude and strong (by the order of magnitude) narrowing of its spectral line. This effect may be related to kind of a quantum stochastic resonance. We show that the fluorescence corresponds to finite domain over the coherent drive with sharp lower threshold and there is splitting of the Wigner function.

  5. DNA fragment sizing and sorting by laser-induced fluorescence

    DOE Patents [OSTI]

    Hammond, Mark L. (Angier, NC); Jett, James H. (Los Alamos, NM); Keller, Richard A. (Los Alamos, NM); Marrone, Babetta L. (Los Alamos, NM); Martin, John C. (Los Alamos, NM)

    1996-01-01T23:59:59.000Z

    A method is provided for sizing DNA fragments using high speed detection systems, such as flow cytometry to determine unique characteristics of DNA pieces from a sample. In one characterization the DNA piece is fragmented at preselected sites to produce a plurality of DNA fragments. The DNA piece or the resulting DNA fragments are treated with a dye effective to stain stoichiometrically the DNA piece or the DNA fragments. The fluorescence from the dye in the stained fragments is then examined to generate an output functionally related to the number of nucleotides in each one of the DNA fragments. In one embodiment, the intensity of the fluorescence emissions from each fragment is linearly related to the fragment length. The distribution of DNA fragment sizes forms a characterization of the DNA piece for use in forensic and research applications.

  6. Rotational order–disorder structure of fluorescent protein FP480

    SciTech Connect (OSTI)

    Pletnev, Sergei, E-mail: svp@ncifcrf.gov [SAIC-Frederick Inc., Basic Research Program, Argonne National Laboratory, 9700 South Cass Avenue, Argonne, IL 60439 (United States); Morozova, Kateryna S.; Verkhusha, Vladislav V. [Department of Anatomy and Structural Biology, Albert Einstein College of Medicine, 1300 Morris Park Avenue, Bronx, New York 10461 (United States); Dauter, Zbigniew, E-mail: svp@ncifcrf.gov [Synchrotron Radiation Research Section, MCL, National Cancer Institute, Argonne National Laboratory, 9700 South Cass Avenue, Argonne, IL 60439 (United States); SAIC-Frederick Inc., Basic Research Program, Argonne National Laboratory, 9700 South Cass Avenue, Argonne, IL 60439 (United States)

    2009-09-01T23:59:59.000Z

    An analysis of the rotational order–disorder structure of fluorescent protein FP480 is presented. In the last decade, advances in instrumentation and software development have made crystallography a powerful tool in structural biology. Using this method, structural information can now be acquired from pathological crystals that would have been abandoned in earlier times. In this paper, the order–disorder (OD) structure of fluorescent protein FP480 is discussed. The structure is composed of tetramers with 222 symmetry incorporated into the lattice in two different ways, namely rotated 90° with respect to each other around the crystal c axis, with tetramer axes coincident with crystallographic twofold axes. The random distribution of alternatively oriented tetramers in the crystal creates a rotational OD structure with statistically averaged I422 symmetry, although the presence of very weak and diffuse additional reflections suggests that the randomness is only approximate.

  7. COMBINED FLUORESCENT AND GOLD PROBES FOR MICROSCOPIC AND MORPHOLOGICAL INVESTIGATIONS.

    SciTech Connect (OSTI)

    POWELL,R.D.HAINFELD,J.F.

    2002-04-17T23:59:59.000Z

    Nanogold{reg_sign}, a gold cluster with a core of gold atoms 1.4 nm in diameter, has proven to be a superior probe label for electron microscopy (EM), giving both higher labeling density and improved access to previously hindered or restricted antigens. It may be visualized by autometallography (AMG) for use in light microscopy (LM): silver-and gold-amplified Nanogold detection has proven to be one of the most sensitive methods available for the detection of low copy number targets such as viral DNA in cells and tissue specimens. AMG enhancement has also made Nanogold an effective detection label in blots and gels. The following protocols will be described: Labeling of nuclear components in cells. Protocol for in situ hybridization and detection with fluorescein-Nanogold--or Cy3{trademark}-Nanogold-labeled streptavidin. Nanogold is an inert molecule, and generally does not interact with biological molecules unless a specific chemical reactivity is introduced into the molecule. Conjugates are prepared using site-specific chemical conjugation through reactive chemical functionalities introduced during Nanogold preparation, which allows the gold label to be attached to a specific site on the conjugate biomolecule. For example, a maleimido-Nanogold derivative, which is specific for thiol binding, is frequently attached to the hinge region of an antibody at a unique thiol site generated by selective reduction of a hinge disulfide. This site is remote from the antigen combining region, and the Nanogold, therefore, does not compromise target binding. Nanogold may also be prepared with specific reactivity towards amines or other unique chemical groups. This mode of attachment enables the preparation of probes labeled with both Nanogold and fluorescent labels. Different chemical reactivities are used to attach the Nanogold and the fluorescent groups to different sites in the conjugate biomolecule, as shown in Figure 7.1. In this manner, the two labels are spaced sufficiently far apart that fluorescent resonance energy transfer does not quench the fluorescent signal, and the probes may be used to label specimens for fluorescent and EM observation in a single staining procedure. This reduces the complexity of the staining procedure, allowing less specimen perturbation, and also enables a higher degree of correlation between the fluorescence and EM localization of the target, thus increasing the usefulness of the complementary data sets. Since gold and fluorescent-labeled probes are often used at different concentrations under different conditions, optimum procedures for the use of fluorescent and gold probes may entail some degree of compromise between the most appropriate conditions for the two types of probes. However, the chemical stability of the Nanogold label means that it is generally stable to a wide range of use conditions, and the following protocols have been found to be effective for labeling specimens with combined fluorescein and Nanogold-labeled antibody Fab' probes and with combined Cy3 and Nanogold-labeled streptavidin.

  8. Development of a fluorescent antibody test for equine infectious anemia

    E-Print Network [OSTI]

    Lester, Thomas Lee

    1972-01-01T23:59:59.000Z

    . Moore The development of a direct fluorescent antibody technique for a reliable laboratory and diagnostic test for equine infectious anemia (EIA) was described. A specific antiserum was produced by inoculation of goats with EIA virus derived from... the Texas and Illinois strains of EIA virus in cell culture and in known infected horses and against the Wyoming strain of EIA virus in inoculated horses. Its specificity was further substantiated by testing it against heterologous viruses including...

  9. Contraband Detection with Nuclear Resonance Fluorescence: Feasibility and Impact

    SciTech Connect (OSTI)

    Pruet, J; Lange, D

    2007-01-03T23:59:59.000Z

    In this report they show that cargo interrogation systems developed to thwart trafficking of illicit nuclear materials could also be powerful tools in the larger fight against contraband smuggling. In particular, in addition to detecting special nuclear materials, cargo scanning systems that exploit nuclear resonance fluorescence to detect specific isotopes can be used to help find: chemical weapons; some drugs as well as some chemicals regulated under the controlled substances act; precious metals; materials regulated under export control laws; and commonly trafficked fluorocarbons.

  10. Dynamic fluorescence imaging with molecular agents for cancer detection

    E-Print Network [OSTI]

    Kwon, Sun Kuk

    2009-05-15T23:59:59.000Z

    emission computed tomography SUV standard uptake values SLN sentinel lymph node TK tyrosine kinase TBR target to background ratio Symbols ? pharmacokinetic parameter ? pharmacokinetic parameter )(tC BOUND concentration of dye... bound to integrin receptor either in the vascular or extravascular compartments )(tC LAREXTRAVASCU concentration of dye in extravascular space )(tC VASCULAR concentration of dye in vascular space 0 I background fluorescence intensity c k...

  11. Nuclear Resonance Fluorescence and Isotopic Mapping of Containers

    SciTech Connect (OSTI)

    Johnson, M S; McNabb, D P

    2008-08-08T23:59:59.000Z

    National security programs have expressed interest in developing systems to isotopically map shipping containers, fuel assemblies, and waste barrels for various materials including special nuclear material (SNM). Current radiographic systems offer little more than an ambiguous density silhouette of a container's contents. In this paper we will present a system being developed at LLNL to isotopically map containers using the nuclear resonance fluorescence (NRF) method. Recent experimental measurements on NRF strengths in SNM are discussed.

  12. Magnetic fluorescent lamp having reduced ultraviolet self-absorption

    DOE Patents [OSTI]

    Berman, Samuel M. (San Francisco, CA); Richardson, Robert W. (Pelham, NY)

    1985-01-01T23:59:59.000Z

    The radiant emission of a mercury-argon discharge in a fluorescent lamp assembly (10) is enhanced by providing means (30) for establishing a magnetic field with lines of force along the path of electron flow through the bulb (12) of the lamp assembly, to provide Zeeman splitting of the ultraviolet spectral line. Optimum results are obtained when the magnetic field strength causes a Zeeman splitting of approximately 1.7 times the thermal line width.

  13. Enhanced detection of fluorescence quenching in labeled cells

    DOE Patents [OSTI]

    Crissman, H.A.; Steinkamp, J.A.

    1987-11-30T23:59:59.000Z

    A method is provided for quantifying BrdU labeled DNA in cells. The BrdU is substituted onto the DNA and the DNA is stained with a first fluorochrome having a fluorescence which is quenchable by BrdU. The first fluorochrome is preferably a thymidine base halogen analogue, such as a Hoechst fluorochrome. The DNA is then stained with a second fluorochrome having a fluorescence which is substantially uneffected by BrdU. The second fluorochrome may be selected from the group consisting of mithramycin, chromomycin A3, olivomycin, propidium iodide and ethidium bromine. The fluorescence from the first and second fluorochromes is then measured to obtain first and second output signals, respectively. The first output signal is subtracted from the second output signal to obtain a difference signal which is functionally related to the quantity of BrdU incorporated into DNA. The technique is particularly useful for quantifying the synthesis of DNA during the S-phase of the cell cycle. 2 figs.

  14. FINAL REPORT FOR MOISTURE EFFECTS ON COMPACTION OF FIBERBOARD IN A 9975 SHIPPING PACKAGE

    SciTech Connect (OSTI)

    Stefek, T.; Daugherty, W.; Estochen, E.

    2013-09-17T23:59:59.000Z

    Compaction of lower layers in the fiberboard assembly has been observed in 9975 packages that contain elevated moisture. Lab testing has resulted in a better understanding of the relationship between the fiberboard moisture level and compaction of the lower fiberboard assembly, and the behavior of the fiberboard during transport. In laboratory tests of cane fiberboard, higher moisture content has been shown to correspond to higher total compaction, greater rate of compaction, and continued compaction over a longer period of time. In addition, laboratory tests have shown that the application of a dynamic load results in higher fiberboard compaction compared to a static load. The test conditions and sample geometric/loading configurations were chosen to simulate the regulatory requirements for 9975 package input dynamic loading. Dynamic testing was conducted to acquire immediate and cumulative changes in geometric data for various moisture levels. Two sample sets have undergone a complete dynamic test regimen, one set for 27 weeks, and the second set for 47 weeks. The dynamic input, data acquisition, test effects on sample dynamic parameters, and results from this test program are summarized and compared to regulatory specifications for dynamic loading. Compaction of the bottom fiberboard layers due to the accumulation of moisture is one possible cause of an increase in the axial gap at the top of the package. The net compaction of the bottom layers will directly add to the axial gap. The moisture which caused this compaction migrated from the middle region of the fiberboard assembly (which is typically the hottest). This will cause the middle region to shrink axially, which will also contribute directly to the axial gap. Measurement of the axial gap provides a screening tool for identifying significant change in the fiberboard condition. The data in this report provide a basis to evaluate the impact of moisture and fiberboard compaction on 9975 package performance during storage at the Savannah River Site (SRS).

  15. ISSUANCE 2014-12-29: Energy Conservation Program: Clarification for Energy Conservation Standards and Test Procedures for Fluorescent Lamp Ballasts

    Broader source: Energy.gov [DOE]

    Energy Conservation Program: Clarification for Energy Conservation Standards and Test Procedures for Fluorescent Lamp Ballasts

  16. Characterization of dissolved organic matter fluorescence in the South Atlantic Bight with use of PARAFAC model: Relationships between fluorescence and its

    E-Print Network [OSTI]

    Durako, Michael J.

    [aCDOM(350)] and CDOM excitation emission matrix (EEM) fluorescence were used to estimate annual (PARAFAC) of CDOM EEM spectra identified six components: three terrestrial humic-like, one marine humic concentration and aCDOM(350), total fluorescence intensity and the intensities of respective EEM components. DOC

  17. Soil compaction is a manageable factor that can lim-it grain or silage yield on many Virginia soils. Corn

    E-Print Network [OSTI]

    Liskiewicz, Maciej

    Soil compaction is a manageable factor that can lim- it grain or silage yield on many Virginia soils. Corn plants growing on compacted areas are often stunted and have slower root penetration rates grown in these areas. Compaction is created when soil particles are pressed together, reducing the pore

  18. STATUS REPORT FOR MOISTURE EFFECTS ON COMPACTION OF FIBERBOARD IN A 9975 SHIPPING PACKAGE

    SciTech Connect (OSTI)

    Stefek, T.; Daugherty, W.; Estochen, E.

    2011-06-23T23:59:59.000Z

    Compaction of lower layers in the fiberboard overpack has been observed in 9975 packages that contain elevated moisture. Lab testing has resulted in a better understanding of the relationship between the fiberboard moisture level and compaction of the lower fiberboard assembly, and the behavior of the fiberboard during transport. In laboratory tests, higher moisture content has been shown to correspond to higher total compaction of fiberboard material, greater rate of compaction, and continued compaction over a longer period of time. In addition, laboratory tests have shown that the application of a dynamic load results in higher fiberboard compaction. The test conditions and sample geometric/loading configurations were chosen to simulate the regulatory requirements for 9975 package input dynamic loading. Dynamic testing was conducted over a period of six months to acquire immediate and cumulative changes in geometric data for various moisture levels. Currently, one sample set has undergone a complete dynamic test regimen, while testing of another set is still in-progress. The dynamic input, data acquisition, test effects on sample dynamic parameters, and interim results from this test program are summarized and compared to regulatory specifications for dynamic loading. This will provide a basis from which to evaluate the impact of moisture and fiberboard compaction on the safety basis for transportation (Safety Analysis Report for Packaging) and storage (facility Documented Safety Analysis) at the Savannah River Site (SRS).

  19. Quasi-static thermal evolution of compact objects

    E-Print Network [OSTI]

    L. Becerra; H. Hernandez; L. A. Nunez

    2014-06-22T23:59:59.000Z

    We study under what conditions the thermal peeling is present for dissipative local and quasi-local anisotropic spherical matter configurations. The thermal peeling occurs when different signs in the velocity of fluid elements appears, giving rise to the splitting of the matter configuration. The evolution is considered in the quasi-static approximation and the matter contents are radiant, anisotropic (unequal stresses) spherical local and quasi-local fluids. The heat flux and the associated temperature profiles are described by causal thermodynamics consistent with this approximation. It is found some particular, local and quasi-local equation of state for ultra-dense matter configurations exhibit thermal peeling when most of the radiated energy is concentrated at the middle of the distribution. This effect, which appears to be associated with extreme astrophysical scenarios (highly relativistic and very luminous gravitational system expelling its outer mass shells), is very sensible to energy flux profile and to the shape of the luminosity emitted by the compact object.

  20. Thermo-Rotational Instability in Plasma Disks Around Compact Objects

    E-Print Network [OSTI]

    Bruno Coppi

    2008-02-12T23:59:59.000Z

    Differentially rotating plasma disks, around compact objects, that are imbedded in a ``seed'' magnetic field are shown to develop vertically localized ballooning modes that are driven by the combined radial gradient of the rotation frequency and vertical gradients of the plasma density and temperature. When the electron mean free path is shorter than the disk height and the relevant thermal conductivity can be neglected, the vertical particle flows produced by of these modes have the effect to drive the density and temperature profiles toward the ``adiabatic condition'' where $\\eta_{T}\\equiv(dlnT/dz)/(dlnn/dz)=2/3$. Here $T$ is the plasma temperature and $n$ the particle density. The faster growth rates correspond to steeper temperature profiles $(\\eta_{T}>2/3)$ such as those produced by an internal (e.g., viscous) heating process. In the end, ballooning modes excited for various values of $\\eta_{T}$ can lead to the evolution of the disk into a different current carrying configuration such as a sequence of plasma rings.

  1. TeV neutrinos from microquasars in compact massive binaries

    E-Print Network [OSTI]

    W. Bednarek

    2005-05-27T23:59:59.000Z

    We consider a compact binary system in which a Wolf-Rayet star supplies matter onto a stellar mass black hole or a neutron star. This matter forms an accretion disk which ejects a jet as observed in Galactic microquasars. A part of the jet kinetic energy, typically 10%, can be transfered to relativistic nuclei. These nuclei lose nucleons as a result of photo-disintegration process in collisions with thermal photons from the accretion disk and the massive star. Due to the head on photon-nucleus collisions most of neutrons released from nuclei move towards the surface of the accretion disk and/or the massive star producing neutrinos in collisions with the matter. We calculate the spectra of muon neutrinos and expected neutrino event rates in a 1 km^2 neutrino detector of the IceCube type from a microquasar inside our Galaxy applying, as an example, the parameters of the Cyg X-3 binary system, provided that nuclei are accelerated to the Lorentz factors above 10^6 with the power law spectrum with an index close to 2.

  2. Hunting for Orphaned Central Compact Objects among Radio Pulsars

    E-Print Network [OSTI]

    Luo, J; Ho, W C G; Bogdanov, S; Kaspi, V M; He, C

    2015-01-01T23:59:59.000Z

    Central compact objects (CCOs) are a handful of young neutron stars found at the center of supernova remnants (SNRs). They show high thermal X-ray luminosities but no radio emission. Spin-down rate measurements of the three CCOs with X-ray pulsations indicate surface dipole fields much weaker than those of typical young pulsars. To investigate if CCOs and known radio pulsars are objects at different evolutionary stages, we carried out a census of all weak-field (<1e11 G) isolated radio pulsars in the Galactic plane to search for CCO-like X-ray emission. None of the 12 candidates is detected at X-ray energies, with luminosity limits of 1e32-1e34 erg/s. We consider a scenario in which the weak surface fields of CCOs are due to rapid accretion of supernova materials and show that as the buried field diffuses back to the surface, a CCO descendant is expected to leave the P-Pdot parameter space of our candidates at a young age of a few times 10kyr. Hence, the candidates are likely to be just old ordinary pulsar...

  3. Arecibo imaging of compact high-velocity clouds

    E-Print Network [OSTI]

    Burton, W B; Chengalur, J N

    2001-01-01T23:59:59.000Z

    Ten isolated compact high-velocity clouds (CHVCs) of the type cataloged by Braun & Burton (1999) have been imaged with the Arecibo telescope and were found to have a nested core/halo morphology. We argue that a combination of high-resolution filled-aperture and synthesis data is crucial to determining the intrinsic properties of the CHVCs. We identify the halos as Warm Neutral Medium surrounding one or more cores in the Cool Neutral Medium phase. These halos are clearly detected and resolved by the Arecibo filled-aperture imaging, which reaches a limiting sensitivity (1 sigma) of N_H about 2x10^17 cm^-2 over the typical 70 km/s linewidth at zero intensity. The FWHM linewidth of the halo gas is found to be 25 km/s, consistent with a WNM thermal broadening within 10^4 K gas. Substantial asymmetries are found at high N_H (>10^18.5 cm^-2) levels in 60% of our sample. A high degree of reflection-symmetry is found at low N_H (<10^18.5 cm^-2) in all sources studied at these levels. The column-density profiles...

  4. A compact, versatile low-energy electron beam ion source

    SciTech Connect (OSTI)

    Zschornack, G., E-mail: g.zschornack@hzdr.de [Department of Physics, Dresden University of Technology, 01062 Dresden, Germany and Helmholtz-Zentrum Dresden-Rossendorf, Institute of Ion Beam Physics and Materials Research, 01328 Dresden (Germany); König, J.; Schmidt, M.; Thorn, A. [DREEBIT GmbH, 01109 Dresden (Germany)] [DREEBIT GmbH, 01109 Dresden (Germany)

    2014-02-15T23:59:59.000Z

    A new compact Electron Beam Ion Source, the Dresden EBIT-LE, is introduced as an ion source working at low electron beam energies. The EBIT-LE operates at an electron energy ranging from 100 eV to some keV and can easily be modified to an EBIT also working at higher electron beam energies of up to 15 keV. We show that, depending on the electron beam energy, electron beam currents from a few mA in the low-energy regime up to about 40 mA in the high-energy regime are possible. Technical solutions as well as first experimental results of the EBIT-LE are presented. In ion extraction experiments, a stable production of low and intermediate charged ions at electron beam energies below 2 keV is demonstrated. Furthermore, X-ray spectroscopy measurements confirm the possibility of using the machine as a source of X-rays from ions excited at low electron energies.

  5. Compact, Low-power and Precision Timing Photodetector Readout

    SciTech Connect (OSTI)

    Varner, Gary S.; Ruckman, Larry L.; /Hawaii U.; Schwiening, Jochen; Vavra, Jaroslav; /SLAC

    2011-06-14T23:59:59.000Z

    Photodetector readout for next generation high event rate particle identification and single-photon detection requires a digitizer capable of integrated recording of dense arrays of sensor elements with high analog bandwidth (precision timing) and large record depth, in a cost-effective, compact and low-power way. Simply stated, one cannot do better than having a high-fidelity 'oscilloscope on a chip' for every sensor channel. A firs version of the Buffered Large Analog Bandwidth (BLAB1) ASIC has been designed based upon the lessons learned from the development of the Large Analog Bandwidth Recorder and Digitizer with Ordered Readout (LABRADOR) ASIC. While this LABRADOR ASIC has been very successful and forms the readout basis of a generation of new, large-scale radio neutrino detectors, its limited sampling depth is a major drawback. To address this shortcoming, a prototype intended for photodetector readout has been designed and fabricated with 64k deep sampling at multi-GSa/s operation. An evaluation system has been constructed for instrumentation of Time-Of-Propagation (TOP) and focusing DIRC prototypes and test results will be reported.

  6. Comprehensive nucleosynthesis analysis for ejecta of compact binary mergers

    E-Print Network [OSTI]

    Just, Oliver; Pulpillo, Ricard Ardevol; Goriely, Stephane; Janka, H -Thomas

    2015-01-01T23:59:59.000Z

    We present a comprehensive study of r-process element nucleosynthesis in the ejecta of compact binary mergers (CBMs) and their relic black-hole (BH)-torus systems. The evolution of the BH-accretion tori is simulated for seconds with a Newtonian hydrodynamics code including viscosity effects, pseudo-Newtonian gravity for rotating BHs, and an energy-dependent two-moment closure scheme for the transport of electron neutrinos and antineutrinos. The investigated cases are guided by relativistic double neutron star (NS-NS) and NS-BH merger models, producing ~3-6 Msun BHs with rotation parameters of A~0.8 and tori of 0.03-0.3 Msun. Our nucleosynthesis analysis includes the dynamical (prompt) ejecta expelled during the CBM phase and the neutrino and viscously driven outflows of the relic BH-torus systems. While typically ~20-25% of the initial accretion-torus mass are lost by viscously driven outflows, neutrino-powered winds contribute at most another ~1%, but neutrino heating enhances the viscous ejecta significantl...

  7. A compact, multichannel, and low noise arbitrary waveform generator

    SciTech Connect (OSTI)

    Govorkov, S. [Sema Systems, 302-5553 16th ave., Delta, British Columbia V4M 2H7 (Canada)] [Sema Systems, 302-5553 16th ave., Delta, British Columbia V4M 2H7 (Canada); Ivanov, B. I. [Leibniz-Institute of Photonic Technology, PO Box 100239, D-07702 Jena (Germany) [Leibniz-Institute of Photonic Technology, PO Box 100239, D-07702 Jena (Germany); Novosibirsk State Technical University, K.Marx-Ave. 20, Novosibirsk 630092 (Russian Federation); Il'ichev, E.; Meyer, H.-G. [Leibniz-Institute of Photonic Technology, PO Box 100239, D-07702 Jena (Germany)] [Leibniz-Institute of Photonic Technology, PO Box 100239, D-07702 Jena (Germany)

    2014-05-15T23:59:59.000Z

    A new type of high functionality, fast, compact, and easy programmable arbitrary waveform generator for low noise physical measurements is presented. The generator provides 7 fast differential waveform channels with a maximum bandwidth up to 200 MHz frequency. There are 6 fast pulse generators on the generator board with 78 ps time resolution in both duration and delay, 3 of them with amplitude control. The arbitrary waveform generator is additionally equipped with two auxiliary slow 16 bit analog-to-digital converters and four 16 bit digital-to-analog converters for low frequency applications. Electromagnetic shields are introduced to the power supply, digital, and analog compartments and with a proper filter design perform more than 110 dB digital noise isolation to the output signals. All the output channels of the board have 50 ? SubMiniature version A termination. The generator board is suitable for use as a part of a high sensitive physical equipment, e.g., fast read out and manipulation of nuclear magnetic resonance or superconducting quantum systems and any other application, which requires electromagnetic interference free fast pulse and arbitrary waveform generation.

  8. Search for Blue Compact Dwarf Galaxies During Quiescence

    E-Print Network [OSTI]

    J. Sanchez Almeida; C. Munoz-Tunon; R. Amorin; J. A. Aguerri; R. Sanchez-Janssen; G. Tenorio-Tagle

    2008-05-21T23:59:59.000Z

    Blue Compact Dwarf (BCD) galaxies are metal poor systems going through a major starburst that cannot last for long. We have identified galaxies which may be BCDs during quiescence (QBCD), i.e., before the characteristic starburst sets in or when it has faded away. These QBCD galaxies are assumed to be like the BCD host galaxies. The SDSS/DR6 database provides ~21500 QBCD candidates. We also select from SDSS/DR6 a complete sample of BCD galaxies to serve as reference. The properties of these two galaxy sets have been computed and compared. The QBCD candidates are thirty times more abundant than the BCDs, with their luminosity functions being very similar except for the scaling factor, and the expected luminosity dimming associated with the end of the starburst. QBCDs are redder than BCDs, and they have larger HII region based oxygen abundance. QBCDs also have lower surface brightness. The BCD candidates turn out to be the QBCD candidates with the largest specific star formation rate (actually, with the largest H_alpha equivalent width). One out of each three dwarf galaxies in the local universe may be a QBCD. The properties of the selected BCDs and QBCDs are consistent with a single sequence in galactic evolution, with the quiescent phase lasting thirty times longer than the starburst phase. The resulting time-averaged star formation rate is low enough to allow this cadence of BCD -- QBCD phases during the Hubble time.

  9. Search for Blue Compact Dwarf Galaxies During Quiescence

    E-Print Network [OSTI]

    Almeida, J Sanchez; Amorin, R; Aguerri, J A; Sanchez-Janssen, R; Tenorio-Tagle, G

    2008-01-01T23:59:59.000Z

    Blue Compact Dwarf (BCD) galaxies are metal poor systems going through a major starburst that cannot last for long. We have identified galaxies which may be BCDs during quiescence (QBCD), i.e., before the characteristic starburst sets in or when it has faded away. These QBCD galaxies are assumed to be like the BCD host galaxies. The SDSS/DR6 database provides ~21500 QBCD candidates. We also select from SDSS/DR6 a complete sample of BCD galaxies to serve as reference. The properties of these two galaxy sets have been computed and compared. The QBCD candidates are thirty times more abundant than the BCDs, with their luminosity functions being very similar except for the scaling factor, and the expected luminosity dimming associated with the end of the starburst. QBCDs are redder than BCDs, and they have larger HII region based oxygen abundance. QBCDs also have lower surface brightness. The BCD candidates turn out to be the QBCD candidates with the largest specific star formation rate (actually, with the largest...

  10. Charged particle driver for ICF using an accelerated, focused compact torus

    SciTech Connect (OSTI)

    Meeker, D.J.; Hammer, J.H.; Hartman, C.W.

    1986-06-01T23:59:59.000Z

    We report the status of evaluating an accelerated and focused compact torus as a driver for ICF. We are studying the acceleration and focusing aspects experimentally in the RACE facility, a recently completed ring generator coupled to a 260 kJ acceleration bank. Compact torus and ICF target interaction is being investigated with PIC codes and LASNEX, a 2D magneto-hydrodynamics code. Final conditions required of the CT are discussed as well as coupling issues such as superthermal electron production. We conclude with an economic evaluation of a few 100 MW reactor driven by a compact torus. 9 refs., 5 figs., 1 tab.

  11. Two methods for characterizing the compaction and ejection behavior of metal powders in a die 

    E-Print Network [OSTI]

    Sajdak, Richard James

    1969-01-01T23:59:59.000Z

    of the compact divided by the ejection load per square inch of the wall surface area of the compact. A~lt*d F Cross Section Area ~E' ' F Wall Surface Area Coefficient of friction Standard chemical abbreviations used throughout. C HAPTER 1 THE POWDER... atmosphere to remove any oxide coating. The powder is blended with a suitable lubricant which is used either to reduce friction or to act as a bonding agent or both. In the compaction process the prepared metal powder is poured into an accurately-made di...

  12. Software Development for a CompactRIO-Based Wire Scanner Control and Data Acquisition SYstem

    SciTech Connect (OSTI)

    Sedillo, James Daniel [Los Alamos National Laboratory

    2012-05-16T23:59:59.000Z

    The Beam Diagnostics and Instrumentation Team at the Los Alamos Neutron Science Center is developing a wire scanner data acquisition and control system with a National Instrument's compactRIO at its core. For this application, the compactRIO controller not only requires programming the FPGA and RT computer internal to the compactRIO, but also requires programming a client computer and a touch panel display. This article will summarize the hardware interfaces and describe the software design approach utilized for programming and interfacing the four systems together in order to fulfill the design requirements and promote reliable interoperability.

  13. A light diet for a giant appetite: An assessment of China's proposed fluorescent lamp standard

    SciTech Connect (OSTI)

    Lin, Jiang

    2002-04-11T23:59:59.000Z

    Lighting has been one of the fastest growing electric end-uses in China over the last twenty years, with an average annual growth rate of 14%. Fluorescent lighting provides a significant portion of China's lighting need. In 1998, China produced 680 million fluorescent lamps, of which 420 million were linear fluorescent lamps of various diameters (T8 to T12). There are substantial variations both in energy efficiency and lighting performance among locally produced fluorescent lamps. Such variations present a perfect opportunity for policy intervention through efficiency standards to promote the adoption of more efficient fluorescent lamps in China. This paper analyzes China's proposed minimum efficiency standard for fluorescent lamps and presents an assessment of its likely impacts on China's lighting energy consumption and GHG emissions.

  14. Air Fluorescence Relevant for Cosmic-Ray Detection - Review of Pioneering Measurements

    E-Print Network [OSTI]

    Fernando Arqueros; Joerg R. Hoerandel; Bianca Keilhauer

    2008-07-24T23:59:59.000Z

    Cosmic rays with energies exceeding $10^{17}$ eV are frequently registered by measurements of the fluorescence light emitted by extensive air showers. The main uncertainty for the absolute energy scale of the measured air showers is coming from the fluorescence light yield of electrons in air. The fluorescence light yield has been studied in laboratory experiments. Pioneering measurements between 1954 and 2000 are reviewed.

  15. Microcavity effects on the generation,fluorescence, and diffusion of excitons in organic solar cells

    E-Print Network [OSTI]

    Kozyreff, G; Vuong, L T; Silleras, O Nieto; Martorell, J

    2013-01-01T23:59:59.000Z

    We compute the short-circuit diffusion current of excitons in an organic solar cell, with special emphasis on fluorescence losses. The exciton diffusion length is not uniform but varies with its position within the device, even with moderate fluorescence quantum efficiency. With large quantum efficiencies, the rate of fluorescence can be strongly reduced with proper choices of the geometrical and dielectric parameters. In this way, the diffusion length can be increased and the device performance significantly improved.

  16. Feedback control of the squeezing of the fluorescence light

    E-Print Network [OSTI]

    Alberto Barchielli; Matteo Gregoratti

    2009-10-09T23:59:59.000Z

    Among the formulations of the theory of quantum measurements in continuous time, quantum trajectory theory is very suitable for the introduction of measurement based feedback and closed loop control of quantum systems. In this paper we present such a construction in the concrete case of a two-level atom stimulated by a coherent, monochromatic laser. In particular, we show how fast feedback \\`a la Wiseman and Milburn can be introduced in the formulation of the theory. Then, the spectrum of the free fluorescence light is studied and typical quantum phenomena, squeezing and sub-natural line-narrowing, are presented.

  17. Quantum Process Tomography by 2D Fluorescence Spectroscopy

    E-Print Network [OSTI]

    Leonardo A. Pachon; Andrew H. Marcus; Alan Aspuru-Guzik

    2015-02-09T23:59:59.000Z

    Reconstruction of the dynamics (quantum process tomography) of the single-exciton manifold in energy transfer systems is proposed here on the basis of two-dimensional fluorescence spectroscopy (2D-FS) with phase-modulation. The quantum-process-tomography protocol introduced here benefits from, e.g., the sensitivity enhancement and signal-to-noise ratio ascribed to 2D-FS. Although the isotropically averaged spectroscopic signals depend on the quantum yield parameter $\\Gamma$ of the doubly-excited-exciton manifold, it is shown that the reconstruction of the dynamics is insensitive to this parameter. Applications to foundational and applied problems, as well as further extensions, are discussed.

  18. Quantum Process Tomography by 2D Fluorescence Spectroscopy

    E-Print Network [OSTI]

    Pachon, Leonardo A; Aspuru-Guzik, Alan

    2015-01-01T23:59:59.000Z

    Reconstruction of the dynamics (quantum process tomography) of the single-exciton manifold in energy transfer systems is proposed here on the basis of two-dimensional fluorescence spectroscopy (2D-FS) with phase-modulation. The quantum-process-tomography protocol introduced here benefits from, e.g., the sensitivity enhancement and signal-to-noise ratio ascribed to 2D-FS. Although the isotropically averaged spectroscopic signals depend on the quantum yield parameter $\\Gamma$ of the doubly-excited-exciton manifold, it is shown that the reconstruction of the dynamics is insensitive to this parameter. Applications to foundational and applied problems, as well as further extensions, are discussed.

  19. Interaction of fluorescent probes with dodecylammonium propionate aggregates in cyclohexane

    E-Print Network [OSTI]

    Correll, Glenn David

    1975-01-01T23:59:59.000Z

    of Added . 01M NaOEL 44 48 51 54 25. Rate P1ot of Carbontetrachloride Quenching of PSA in DAP/Cyclohexane. 26. Rate Plots of KSr Quenching of PSA. in DAP/Cyclohexane 58 at Different Stoichiometric Concentrations of Hs0. . . . . 61 27. KBr... Quenching Rate vs. Aqueous Volume. . . . . . . . . . . . . 28. PSA Fluorescence Lifetimes vs. Aqueous Volume of Constant KBr Concentration (4. OM KBr/0. 01M NaOH). . . 29. Plot of' ?. /(I- ?. ) vs. [DAP] for PSA in Cyclohexane at Constant Water...

  20. Blue-green phosphor for fluorescent lighting applications

    DOE Patents [OSTI]

    Srivastava, Alok; Comanzo, Holly; Manivannan, Venkatesan; Setlur, Anant Achyut

    2005-03-15T23:59:59.000Z

    A fluorescent lamp including a phosphor layer including Sr.sub.4 Al.sub.14 O.sub.25 :Eu.sup.2+ (SAE) and at least one of each of a red, green and blue emitting phosphor. The phosphor layer can optionally include an additional, deep red phosphor and a yellow emitting phosphor. The resulting lamp will exhibit a white light having a color rendering index of 90 or higher with a correlated color temperature of from 2500 to 10000 Kelvin. The use of SAE in phosphor blends of lamps results in high CRI light sources with increased stability and acceptable lumen maintenance over, the course of the lamp life.