Powered by Deep Web Technologies
Note: This page contains sample records for the topic "210-s machine shop" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


1

Heavy Machine Shop | Central Fabrication Services | Brookhaven...  

NLE Websites -- All DOE Office Websites (Extended Search)

Heavy Machine Shop Heavy Machine Shop The Heavy Machine Shop facility is located in building 479, and may be accessed by the main door on the north face or front of the building....

2

Machine Shop Investigates PQ Issues  

Science Conference Proceedings (OSTI)

EPRI performed a power quality (PQ) audit to harden a machine shop against PQ-related issues. EPRI engineers investigated the various origins of existing PQ disturbances as well as the susceptibility of the plant equipment to these disturbances. This case study reports the findings of this detailed investigation.

2007-12-31T23:59:59.000Z

3

MACHINE SHOP SAFETY POLICY THE WYSS INSTITUTE  

E-Print Network (OSTI)

Health 210 Lincoln Street 617-432-1370 617-355-7580 617-632-0710 617-632-3016 617-353-6630 617 Research Building (NRB) Security: For lockouts and escorts 617-432-6119 Harvard Custodial Services 617 in the Wyss Institute for Biologically Inspired Engineering (Wyss Institute) light machine shops in the Center

Church, George M.

4

General Orientation to the Building 433 LOM Machine Shop  

NLE Websites -- All DOE Office Websites (Extended Search)

grinder in the LOM Machine Shop to grind non-ferrous materials (e.g., aluminum, brass, plastics, or wood). * Contact the Shop Coordinator or an APS Floor Coordinator if you...

5

CRAD, Machine Shop Safe Operations Assessment Plan | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Machine Shop Safe Operations Assessment Plan Machine Shop Safe Operations Assessment Plan CRAD, Machine Shop Safe Operations Assessment Plan Performance Objective: The purpose of this assessment is to verify that machine shop operators are provided a safe and healthful workplace which will reduce or prevent injuries, illnesses, and accidental losses. Criteria: A worker protection program shall be implemented that provides a place of employment free from recognized hazards that are causing or likely to cause death or serious physical harm. (DOE O 440.1A Contractor Requirements Document (CRD)) Employees shall be encouraged to become involved in the identification and control of hazards in the workplace. (DOE O 440.1A CRD) Workers shall have the right, without reprisal, to accompany DOE worker protection personnel during workplace inspections. (DOE O44.1A

6

Scheduling trains as a blocking parallel-machine job shop scheduling problem  

Science Conference Proceedings (OSTI)

In this paper, the train scheduling problem is modelled as a blocking parallel-machine job shop scheduling (BPMJSS) problem. In the model, trains, single-track sections and multiple-track sections, respectively, are synonymous with jobs, single machines ... Keywords: Blocking, Job shop scheduling, Parallel machine, Train scheduling

Shi Qiang Liu; Erhan Kozan

2009-10-01T23:59:59.000Z

7

Machine Shop Safe Operations Assessment Plan, 7/03 | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Machine Shop Safe Operations Assessment Plan, 7/03 Machine Shop Safe Operations Assessment Plan, 7/03 Machine Shop Safe Operations Assessment Plan, 7/03 The purpose of this assessment is to verify that machine shop operators are provided a safe and healthful workplace which will reduce or prevent injuries, illnesses, and accidental losses. A worker protection program shall be implemented that provides a place of employment free from recognized hazards that are causing or likely to cause death or serious physical harm. (DOE O 440.1A Contractor Requirements Document (CRD)) Machine-Shop.doc More Documents & Publications MAINTENANCE Assessment Plan, NNSA/Nevada Site Office Facility Representative Division Order Module--DOE O 440.1B, WORKER PROTECTION PROGRAM FOR DOE (INCLUDING NNSA) FEDERAL EMPLOYEES DOE-STD-6005-01

8

Machine Shop Safe Operations Assessment Plan - Developed By NNSA/Nevada Site Office Facility Representative Division  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

July 2003 - Machine Shop Safe Operations July 2003 - Machine Shop Safe Operations Utilize 29 CFR 1910 Utilize applicable LLNL, LANL, DTRA, BN procedures VALUE ADDED FOR: AMTS Contractor Assurance Focus Area AMTS ISM Improvements Focus Area AMTS Safety Precursors/Hazards Analysis Focus Area AMTS Environment, Safety, & Health Division MACHINE SHOP SAFE OPERATIONS Assessment Plan NNSA/Nevada Site Office Independent Oversight Division Performance Objective: The purpose of this assessment is to verify that machine shop operators are provided a safe and healthful workplace which will reduce or prevent injuries, illnesses, and accidental losses. Criteria: A worker protection program shall be implemented that provides a place of employment free from recognized hazards that are causing or likely to cause

9

A hybrid heuristic to solve the parallel machines job-shop scheduling problem  

Science Conference Proceedings (OSTI)

This paper presents an advanced software system for solving the flexible manufacturing systems (FMS) scheduling in a job-shop environment with routing flexibility, where the assignment of operations to identical parallel machines has to be managed, in ... Keywords: Ant colony optimization, Genetic algorithms, Hybrid systems, Parallel machines, Statistical analysis

Andrea Rossi; Elena Boschi

2009-02-01T23:59:59.000Z

10

Design of a desktop milling machine for fabrication in an introductory machine shop class  

E-Print Network (OSTI)

The purpose of this research is to design, fabricate and test the electromechanical subsystem of a CNC milling machine kit. Unlike all other CNC kits on the market, the purpose of this kit is to teach students the principles ...

Lorenc, Dan (Daniel P.)

2010-01-01T23:59:59.000Z

11

IRLab shop area  

NLE Websites -- All DOE Office Websites (Extended Search)

The IRLab machine tool shop contains a variety of equipment for working with metal, wood, and plastic. This facility is used extensively by researchers from in the Optics Lab...

12

APS LOM Shop Usage  

NLE Websites -- All DOE Office Websites (Extended Search)

Division XSD Groups Industry Argonne Home Advanced Photon Source APS LOM Shop Usage User Shop Access - Policies and Procedures User Shop Orientation User Shop...

13

LOM_Shop_Monthly_Inspection_Record.xls  

NLE Websites -- All DOE Office Websites (Extended Search)

ˆš Satisfactory ˆš Satisfactory R Requires follow-up U Urgent attention required Outside postings: Eye protection required; Authorized users only; User Shop Access List, Lead postings Inside postings: User Shop Access List; Machine Daily Checklists, Lead postings, Safety Rules Date Deficiencies corrected Outside postings Visitors safety glasses Inside postings Overhead & task lamps OK Work table clean; machines free of debris Clamping mechanisms OK Machines anchored to floor Access to emergency power disconnects Auto machine restart inhibit working OK Egress aisles clear Machine working areas clear General housekeeping No tripping hazards Spill control kit available Waste lead container in place & labeled Oily rag container in place & labeled General Vacuum OK with correct

14

Machining  

NLE Websites -- All DOE Office Websites (Extended Search)

laboratory equipment. Machinery includes live spindle tooling lathes, CNC lathes, CNC milling machines, wire-cut EDMs, a high-speed machining center and a CNC four-axis EDM...

15

A heuristic for minimizing the makespan in no-idle permutation flow shops  

Science Conference Proceedings (OSTI)

The paper deals with the problem of finding a job sequence that minimizes the makespan in m-machine flow shops under the no-idle condition. This condition requires that each machine must process jobs without any interruption from the start of processing ... Keywords: Flow shop, Heuristics, Makespan, No-idle machines, Scheduling

Pawel Jan Kalczynski; Jerzy Kamburowski

2005-08-01T23:59:59.000Z

16

Comparison shopping on the internet  

Science Conference Proceedings (OSTI)

Though comparison shopping is used widely by online shoppers, very little research exists about how comparison shoppers differ from those who are not involved in comparison shopping. A survey of 208 US consumers identified comparison shoppers, both on ... Keywords: USA, United States, comparison shopping, consumer attitudes, e-commerce, e-shopping, e-tailing, electronic commerce, electronic retailing, factors, internet, online shopping

Michael Klassen; Pola Gupta; Matthew P. Bunker

2009-05-01T23:59:59.000Z

17

Argonne Software Shop  

Argonne Software Shop. Argonne's researchers have created a wealth of powerful software and models with broad-ranging applications. In addition to ...

18

The urban coffee shop  

E-Print Network (OSTI)

This thesis is an investigation of the role of the coffee shop in the urban environment throughout history. Coffee shops spread from the Arab world to Europe and then to the U.S. at the end of the seventeenth century. ...

Chadios, Konstantinos

2005-01-01T23:59:59.000Z

19

Review: Virtual machine tools and virtual machining-A technological review  

Science Conference Proceedings (OSTI)

Virtual manufacturing systems provide a useful means for products to be manufactured 'right the first time' without the need of physical testing on the shop floor. Earlier research was mostly on developing a virtual manufacturing environment. Over the ... Keywords: Machining simulation, Virtual machine tool, Virtual machining, Virtual system

Aini Abdul Kadir; Xun Xu; Enrico Hämmerle

2011-06-01T23:59:59.000Z

20

Jack Case ? the man who helped bring uranium machining to Y...  

NLE Websites -- All DOE Office Websites (Extended Search)

the man who helped bring uranium machining to Y-12 Most of you realize that Y-12 is basically a huge and very precise machine shop. For years it has been the nation's only uranium...

Note: This page contains sample records for the topic "210-s machine shop" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


21

Design guidelines for downtown shopping centers  

E-Print Network (OSTI)

This thesis focuses on urban design issues germane to downtown shopping center design. The underlying concept is that, all new downtown shopping centers should attempt to build upon the existing fabric in such a way as to ...

McGhee, Billy Kevin

1987-01-01T23:59:59.000Z

22

Remote Food Shopping Robot System in a Supermarket Realization of the shopping task from remote places  

E-Print Network (OSTI)

the experimental result performed with the integrated system. Index Terms-- Remote shopping, Foods handling, Human dailylifeRemote shopping, Foods handling, Human dailylife I. INTRODUCTION In this research we focusedRemote Food Shopping Robot System in a Supermarket ­Realization of the shopping task from remote

Ohya, Akihisa

23

CAST SHOP TECHNOLOGY: V: Cast House Safety  

Science Conference Proceedings (OSTI)

TMS Logo. 1997 TMS Annual Meeting: Wednesday Session. CAST SHOP TECHNOLOGY: Session V: Cast House Safety. Sponsored by: LMD Aluminum ...

24

Developing an improved production planning method for a machining cell using an active-nondelay hybrid scheduling technique  

E-Print Network (OSTI)

We examine the production planning and scheduling of a job shop environment of a machining cell in a manufacturing facility. This thesis addresses the scheduling limitations in the machining cell that can result in unbalanced ...

Tan, Wei Yung

2010-01-01T23:59:59.000Z

25

One Stop Information Shop: Personalized Content Recommendations  

4 Managed by UT-Battelle One Stop Information Shop: Personalized Content Recommendations for the U.S. Department of Energy Technology Leadership

26

One Stop Information Shop: Personalized Content Recommendations  

Onefor the U.S. Department of Energy Stop Information Shop Problem . 3 Managed by UT-Battelle ... • Concept works in prototype, market acceptance unknown

27

Safety_Tips_for_Christmas_Shopping-DEC-2011  

NLE Websites -- All DOE Office Websites (Extended Search)

Christmas Shopping The holiday shopping season can be a time of great joy safety risks. Below are some safety tips to keep in mind while shopping. * Carry a cell phone and program...

28

Property:Building/FloorAreaGroceryShops | Open Energy Information  

Open Energy Info (EERE)

for Grocery shops Retrieved from "http:en.openei.orgwindex.php?titleProperty:BuildingFloorAreaGroceryShops&oldid286018" What links here Related changes Special pages...

29

Microsoft Word - 2.6 Shop Managers 0913.docx  

NLE Websites -- All DOE Office Websites (Extended Search)

Shop Managers Shop Managers Shop Managers, as described in ES&H Manual Chapter 25, are a special type of Work Lead appointed by AFRD Program Heads to assist in monitoring work in AFRD shops. The Shop Manager must be a person who can, through experience, sufficient knowledge, or training, operate the equipment safely, and identify and mitigate hazards associated with the work performed in the shop. The Shop Manager: * Completes any training required for Shop Managers; * Has demonstrated experience in the safe operation of the equipment in the shop; * Determines whether other personnel are competent and qualified to operate specific pieces of equipment in the shop; * Determines who may use the equipment, and how and when they may do so ES&H Manual Chapter 25, Section 25.7 Work Process A, 2.a.xvi and

30

Tips: Shopping for Appliances | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Tips: Shopping for Appliances Tips: Shopping for Appliances Tips: Shopping for Appliances April 24, 2012 - 7:33pm Addthis What's the Real Cost? Every appliance has two price tags -- the purchase price and the operating cost. Consider both when buying a new appliance. What's the Real Cost? Every appliance has two price tags -- the purchase price and the operating cost. Consider both when buying a new appliance. When you're shopping for appliances, think of two price tags. The first one covers the purchase price -- think of it as a down payment. The second price tag is the cost of operating the appliance during its lifetime. You'll be paying on that second price tag every month with your utility bill for the next 10 to 20 years, depending on the appliance. Refrigerators last an average of 12 years; clothes washers about 11 years; dishwashers

31

Enabling Technologies for Communities at Web Shops  

Science Conference Proceedings (OSTI)

This paper identifies needs for communities at web shops. Different types of communities are classified and rated according to their value for e-commerce sites. Three virtual stores and one external instant messaging and presence tool are observed regarding ...

Till Schümmer

2002-04-01T23:59:59.000Z

32

Building Green in Greensburg: Dillons Kwik Shop  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Dillons Kwik Shop Dillons Kwik Shop After a tornado destroyed 95% of Greensburg, Kansas, in May 2007, residents needed a convenience store for gas and groceries. Just a year after the storm, Kroger Company broke ground on a prototype for rural grocery stores. Completed in February 2009, the new Dillons Kwik Shop is a hybrid between a convenience store and a gas station. Kroger Company hopes this type of store will serve the grocer needs of several rural county areas. Additionally, this building includes a number of unique green building and energy efficiency features. ENERGY EFFICIENCY FEATURES * Well-insulated roof with an R-value of R-24 that prevents heat loss and maintains cooler temperatures in summer * A high albedo reflective roof coating reflects heat away from the building in

33

The Research of Internet Shopping Customer Value Model  

Science Conference Proceedings (OSTI)

The existing empirical study of Internet shopping in literature, mostly concerned about the interaction relationship of retailer and customer, few scholars study the process of transactions between customers and other services suppliers, by assaying ... Keywords: Internet Shopping, Stakeholders, Customer Value

Xiao-bin Liu; Ming-qing Qiu

2010-05-01T23:59:59.000Z

34

Search Strategies in Shopping Engines: An Experimental Investigation  

Science Conference Proceedings (OSTI)

Shopping engines of different designs were researched in respect to convenience as a mode of access to goods and services offered on the Web. Some shopping engines function autonomously in one stage, quickly maximizing decision accuracy as a function ... Keywords: Consumer Behavior, Data-Envelopment Analysis, Decision Support, On-Line Commerce, Preference Elicitation, Recall, Shopping Engines

Arnold Kamis

2006-10-01T23:59:59.000Z

35

Tips: Shopping for Lighting | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Tips: Shopping for Lighting Tips: Shopping for Lighting Tips: Shopping for Lighting July 29, 2012 - 7:27pm Addthis With an array of lighting options, use the Lighting Facts label to determine the right lightbulb for you. | Photo courtesy of Michelle Vigen, Clean Energy Resource Teams. With an array of lighting options, use the Lighting Facts label to determine the right lightbulb for you. | Photo courtesy of Michelle Vigen, Clean Energy Resource Teams. When shopping for lighting, you can now use the Lighting Facts label and lumens to compare bulbs and purchase a bulb with the amount of brightness you want. The Lighting Facts Label Lighting facts per bulb label. The label is an example showing the brightness at 800 lumens, estimated yearly energy cost at $1.57, based on 3 hours per day and 11 cents per kWh. Cost depends on rates and use. The life is 9 years and is based on 3 hours per day. Light appearance is warm at 2700 K. Energy used is 13 watts, and the bulb is ENERGY STAR rated.

36

Gas Turbine Component Repair Shop Capabilities  

Science Conference Proceedings (OSTI)

Aftermarket repair services for gas turbine OM has been undergoing continual transformation beginning with the emergence of independent shops in the 1980s. The original equipment manufacturers (OEMs) in the late 1990s began to aggressively pursue repair services. Gas turbine hot section component repair/replacement coupled with inspection/overhaul technical support has come to be offered as long-term service agreements (LTSAs). These agreements often extend from 6 to 18 years. The repair business continu...

2011-12-16T23:59:59.000Z

37

Safety_Tips_for_Christmas_Shopping-DEC-2011  

NLE Websites -- All DOE Office Websites (Extended Search)

for Christmas Shopping for Christmas Shopping The holiday shopping season can be a time of great joy safety risks. Below are some safety tips to keep in mind while shopping. * Carry a cell phone and program emergency and * If you plan on carrying a purse or handbag, carry it as clo body as possible. * Try to shop during the daytime hours and bring a friend or family member Safety in numbers! * Carry minimal amounts of cash. * Have credit card numbers and customer service numbers case. * If your card(s) are lost or stolen, call the credit card loss. * Do not overload yourself with packages. * If you must leave purchases * When walking to the parkin * When unloading the content purse unattended in the shopping cart. * Be cautious of anyone who approaches you in a parking lot or in a store. It could be a

38

Insanely Fast Microprocessor Shop - Vulnerability Assessment Team - Nuclear  

NLE Websites -- All DOE Office Websites (Extended Search)

Insanely Fast Microprocessor Shop Insanely Fast Microprocessor Shop VAT Projects Introducing the VAT Adversarial Vulnerability Assessments Safety Tags & Product Counterfeiting Election Security Spoofing GPS Defeating Existing Tamper-Indicating Seals Specialty Field Tools & Sampling Tools Insider Threat Mitigation Drug Testing Security Microprocessor Prototypes The Journal of Physical Security Vulnerability Assessments Vulnerability Assessments Insanely Fast µProcessor Shop Insanely Fast µProcessor Shop Seals About Seals Applications of Seals Common Myths about Tamper Indicating Seals Definitions Findings and Lessons Learned New Seals Types of Seals Seals References Selected VAT Papers Selected VAT Papers Selected Invited Talks Self-Assessment Survey Security Maxims Devil's Dictionary of Security Terms

39

Flow shop scheduling with peak power consumption constraints  

E-Print Network (OSTI)

Mar 29, 2012 ... In particular, we consider a flow shop scheduling problem with a restriction on peak power consumption, in addition to the traditional ...

40

Mining Skewed and Sparse Transaction Data for Personalized Shopping Recommendation  

Science Conference Proceedings (OSTI)

A good shopping recommender system can boost sales in a retailer store. To provide accurate recommendation, the recommender needs to accurately predict a customer's preference, an ability difficult to acquire. Conventional data mining techniques, such ... Keywords: collaborative filtering, graphical models, shopping recommendation, transaction data, user profiles

Chun-Nan Hsu; Hao-Hsiang Chung; Han-Shen Huang

2004-10-01T23:59:59.000Z

Note: This page contains sample records for the topic "210-s machine shop" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


41

A study of interactive qualitative at online shopping behavior  

Science Conference Proceedings (OSTI)

As the information age arrives and the internet network has very popular day by day. Internet network has already become quite important activity in people's daily life. The research shows that there are more than 650 million non-repeating users shop ... Keywords: interactive qualitative analysis (IQA), interactive qualitative research, on-line shopping, transaction cost

Chien-Yuan Lai; Dong-Her Shih; Hsiu-Sen Chiang; Ching-Chiang Chen

2010-02-01T23:59:59.000Z

42

Electric machine  

SciTech Connect

An interior permanent magnet electric machine is disclosed. The interior permanent magnet electric machine comprises a rotor comprising a plurality of radially placed magnets each having a proximal end and a distal end, wherein each magnet comprises a plurality of magnetic segments and at least one magnetic segment towards the distal end comprises a high resistivity magnetic material.

El-Refaie, Ayman Mohamed Fawzi (Niskayuna, NY); Reddy, Patel Bhageerath (Madison, WI)

2012-07-17T23:59:59.000Z

43

Post-Holiday Holiday Shopping | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Post-Holiday Holiday Shopping Post-Holiday Holiday Shopping Post-Holiday Holiday Shopping January 10, 2012 - 4:31pm Addthis Elizabeth Spencer Communicator, National Renewable Energy Laboratory Ah, January. It's still cold and it's still dark all the time, but now all the cheerful Christmas lights have come down so there's nothing to break up the monotony. What's there to do? Well, while it's a little late now, you might want to go do some post-holiday holiday shopping. Yes, I know. That sounds insane. Everyone is thoroughly sick of holiday shopping. You've spent enough money already. I know. But I was out wandering through the stores during the first week of January when I happened to pass by heavily discounted holiday products. And in that great wasteland of 50% off products and half-empty shelves, I found a vast

44

Green your Back to School Shopping List! | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Green your Back to School Shopping List! Green your Back to School Shopping List! Green your Back to School Shopping List! August 23, 2013 - 10:06am Addthis Save energy and money while buying school supplies this year. | Photo courtesy of ©iStockphoto/Ls9907 Save energy and money while buying school supplies this year. | Photo courtesy of ©iStockphoto/Ls9907 Agatha Wein Communications Specialist, State Energy Program How can I participate? You can save energy and money this fall by simply reducing, reusing, and recycling school supplies. It seems back-to-school shopping lists get longer every year! This year, you can reduce the impact your back-to-school shopping has on energy and the environment by making a few simple choices. Just use the mantra: reuse, reduce, recycle! Reuse Reusing items is the best way to minimize the environmental and energy

45

Meso-machining  

NLE Websites -- All DOE Office Websites (Extended Search)

following meso-machin- ing technologies: * Focused ion beam (FIB) machining, * Micro-milling and -turning, * Femto-second laser machining * Micro-Electro Discharge Machining...

46

MAINTENANCE SHOP The shop manager, Clint Steffan has over 25 years experience in Electronic design, test, and repair in  

E-Print Network (OSTI)

MAINTENANCE SHOP The shop manager, Clint Steffan has over 25 years experience in Electronic design the capability of repairing most electronic, mechanical and electro-mechanical equipment, including refrigeration source for parts instead of buying from equipment manufacturer. Repair/recharge small refrigeration

Lajeunesse, Marc J.

47

Machine therapy  

E-Print Network (OSTI)

Machine Therapy is a new practice combining art, design, psychoanalysis, and engineering work in ways that access and reveal the vital, though often unnoticed, relevance of people's interactions and relationships with ...

Dobson, Kelly E. (Kelly Elizabeth), 1970-

2007-01-01T23:59:59.000Z

48

DOE - Office of Legacy Management -- Transcontinental Machine and Tool Co -  

NLE Websites -- All DOE Office Websites (Extended Search)

Transcontinental Machine and Tool Transcontinental Machine and Tool Co - US 06 FUSRAP Considered Sites Site: TRANSCONTINENTAL MACHINE AND TOOL CO. (US.06 ) Eliminated from further consideration under FUSRAP Designated Name: Not Designated Alternate Name: None Location: Unknown US.06-1 Evaluation Year: 1990 US.06-1 Site Operations: Metal Fabrication operations - Machined Uranium slugs in support of Savannah River program for evaluation of Uranium fabrication methods. US.06-1 Site Disposition: Eliminated - Based on similar AEC/MED machine shops' surveys with low potential for contamination - did not exceed DOE guidelines US.06-1 Radioactive Materials Handled: Yes Primary Radioactive Materials Handled: Uranium US.06-1 Radiological Survey(s): None Indicated Site Status: Eliminated from further consideration under FUSRAP

49

Weatherization Assistance Available at Florida Pie Shop | Department of  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Weatherization Assistance Available at Florida Pie Shop Weatherization Assistance Available at Florida Pie Shop Weatherization Assistance Available at Florida Pie Shop June 29, 2010 - 10:00am Addthis Malea Guiriba uses a portion of profits from her pie business to fund weatherization projects for local residents. | Photo courtesy of Malea Guiriba Malea Guiriba uses a portion of profits from her pie business to fund weatherization projects for local residents. | Photo courtesy of Malea Guiriba Pie in the Sky, a seemingly simple store that offers customers fresh-baked desserts, is providing a second treat: weatherization. Local resident Malea Guiriba opened the pie shop in the small town of Hastings, Fla., last summer and started using part of the store's profits to help weatherize homes of low-income residents in the area. She did all

50

Business expansion and lean transformation for helicopter blade shop  

E-Print Network (OSTI)

Sikorsky Aircraft is undergoing a lean transformation as its helicopter blade line is relocated from Stratford to Site B. Value Stream Mapping is a vital tool to eliminate sources of waste in the existing blade shop and ...

Bar, S. Neil (Saumen Neil)

2006-01-01T23:59:59.000Z

51

HEART SMART NUTRITION Heart Smart Shopping & Label Reading  

E-Print Network (OSTI)

Lesson 3 HEART SMART NUTRITION Heart Smart Shopping & Label Reading What's the first step in fat. Your goal is to eat a diet lower in saturated fat, trans fat, and cholesterol. The National Heart

52

Cost Effective Machining Of Ceramics (CEMOC)  

SciTech Connect

The purpose of the CEMOC program was to support U.S. industry needs in fabricating precision components, from difficult to machine materials, while maintaining and enhancing the precision manufacturing skills of the Oak Ridge Complex. Oak Ridge and partner company personnel worked in a team relationship wherein each contributed equally to the success of the program. In general, Oak Ridge contributed a wider range of expertise to a given task while the companies provided operations-specific equipment and shop-floor services. Process control technologies, machining procedures and parameters, and coolant-related environmental tasks were the primary focus areas. The companies were very pleased with the results of the CRADAs and are planning on continuing the relationships. Finish machining operations contribute the majority of the costs associated with fabricating high quality ceramic products. These components are typically used in harsh environments such as diesel engines, defense machinery, and automotive components. The required finishing operations involve a variety of technologies including process controls, machine coolants, product certification, etc. and are not limited only to component grinding methods. The broad range of manufacturing problem solving expertise available in Oak Ridge provided resources that were far beyond what are typically available to the CRADA partners. These partners contributed equipment, such as state-of-the-art machine tools, and operation-specific experience base. In addition, addressing these challenging tasks enabled Oak Ridge personnel to maintain familiarity with rapidly advancing technologies, such as those associated with computer control systems.

Barkman, W.E.

1997-04-18T23:59:59.000Z

53

Induction machine  

DOE Patents (OSTI)

A polyphase rotary induction machine for use as a motor or generator utilizing a single rotor assembly having two series connected sets of rotor windings, a first stator winding disposed around the first rotor winding and means for controlling the current induced in one set of the rotor windings compared to the current induced in the other set of the rotor windings. The rotor windings may be wound rotor windings or squirrel cage windings.

Owen, Whitney H. (Ogden, UT)

1980-01-01T23:59:59.000Z

54

JEA - ShopSmart Residential Rebate Program | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

JEA - ShopSmart Residential Rebate Program JEA - ShopSmart Residential Rebate Program JEA - ShopSmart Residential Rebate Program < Back Eligibility Multi-Family Residential Residential Savings Category Home Weatherization Commercial Weatherization Heating & Cooling Commercial Heating & Cooling Cooling Appliances & Electronics Sealing Your Home Ventilation Heat Pumps Commercial Lighting Lighting Windows, Doors, & Skylights Maximum Rebate Limit one rebate per appliance type per customer Insulation: $250 Program Info Start Date 12/01/2009 State Florida Program Type Utility Rebate Program Rebate Amount CFLs: Up to a $1.25 markdown per product in stores Refrigerators: $25 Clothes Washers: $25 Window Film/Solar Screens: $30/window - South, east, and west exposures only - up to $300 Insulation: $0.30/square foot

55

Land of Enchantment's Appliance Rebate Program Spurs Shopping | Department  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Land of Enchantment's Appliance Rebate Program Spurs Shopping Land of Enchantment's Appliance Rebate Program Spurs Shopping Land of Enchantment's Appliance Rebate Program Spurs Shopping September 20, 2010 - 10:00am Addthis Lindsay Gsell What does this project do? Issued 8830 appliance rebates in Arizona. One local business saw an 80% sales increase weeks after the launch of the appliance rebate program. Rebates can add up quickly - especially when 8,830 are issued. Through Recovery Act funding, New Mexico has distributed about 8,830 rebates worth $200 for ENERGY STAR qualified refrigerators, clothes washers and gas furnaces. The state's appliance rebate program launched on April 22 -- Earth Day -- and is currently winding down, with a little more than $125,000 available for furnace rebates. Program manager Harold Trujillo says that more than half the rebates were

56

Property:Building/FloorAreaShops | Open Energy Information  

Open Energy Info (EERE)

Property Property Edit with form History Facebook icon Twitter icon » Property:Building/FloorAreaShops Jump to: navigation, search This is a property of type Number. Floor area for Shops Pages using the property "Building/FloorAreaShops" Showing 19 pages using this property. S Sweden Building 05K0002 + 900 + Sweden Building 05K0009 + 800 + Sweden Building 05K0012 + 1,587 + Sweden Building 05K0013 + 154 + Sweden Building 05K0017 + 3,150 + Sweden Building 05K0018 + 245 + Sweden Building 05K0019 + 5,600 + Sweden Building 05K0035 + 292 + Sweden Building 05K0046 + 530 + Sweden Building 05K0062 + 940 + Sweden Building 05K0081 + 530 + Sweden Building 05K0086 + 920 + Sweden Building 05K0088 + 1,170 + Sweden Building 05K0089 + 976 + Sweden Building 05K0092 + 360 +

57

New Lighting Facts Label: Takes the Guess Work Out of Shopping...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Lighting Facts Label: Takes the Guess Work Out of Shopping for Light Bulbs New Lighting Facts Label: Takes the Guess Work Out of Shopping for Light Bulbs January 25, 2012 - 5:52am...

58

Accelerating Turing Machines  

Science Conference Proceedings (OSTI)

Accelerating Turing machines are Turing machines of a sort able to perform tasks that are commonly regarded as impossible for Turing machines. For example, they can determine whether or not the decimal representation of ? contains n consecutive 7s, ... Keywords: ?-machine, Chinese room argument, Church–Turing thesis, accelerating Turing machine, decision problem, effective procedure, halting problem, hypercomputation, hypercomputer, infinity machine, oracle machine, super-task

B. Jack Copeland

2002-05-01T23:59:59.000Z

59

Remote Shopping Robot System for Fresh Foods Development of the foods grasping mechanism  

E-Print Network (OSTI)

of this mechanism, and shows performance. Key Words: Remote shopping, Mobile Manipulator, Foods handling 1. 1·1 1) 1Remote Shopping Robot System for Fresh Foods ­Development of the foods grasping mechanism­ Tetsuo) Abstract-- Our purpose is developing the remote shopping system as a concrete application. A human uses

Ohya, Akihisa

60

IMPACTing SHOP: Putting an AI Planner Into a Multi-Agent Environment  

Science Conference Proceedings (OSTI)

In this paper we describe a formalism for integrating the SHOP HTN planning system with the IMPACT multi-agent environment. We define the A-SHOP algorithm, an agentized adaptation of the SHOP planning algorithm that takes advantage of IMPACT's capabilities ... Keywords: HTN planning, heterogenous/distributed data, multi-agent systems

Jürgen Dix; Héctor Muñoz-Avila; Dana S. Nau; Lingling Zhang

2003-04-01T23:59:59.000Z

Note: This page contains sample records for the topic "210-s machine shop" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


61

Designing a cross-language comparison-shopping agent  

Science Conference Proceedings (OSTI)

This research pertains to the design and development of a shopbot called WebShopper+. This shopbot is intended to help customers find and compare e-tailers that market their wares using different languages. WebShopper+ is built with a multilingual ontology ... Keywords: Comparison-shopping, Formal concept analysis, Ontology, Semantic similarity, Shopbot

Shiu-Li Huang; Yu-Hsiang Tsai

2011-01-01T23:59:59.000Z

62

Resource Constraints for Preemptive Job-shop Scheduling  

Science Conference Proceedings (OSTI)

This paper presents an experimental study of constraint propagation algorithms for preemptive scheduling. We propose generalizations of non-preemptive constraint propagation techniques (based on timetables, on disjunctive constraints, and on edge-finding) ... Keywords: constraint propagation, disjunctive constraints, edge-finding, job-shop scheduling, network flows, preemptive scheduling, resource constraints, timetables

Claude Le Pape; Philippe Baptiste

1998-10-01T23:59:59.000Z

63

NORTH PORTAL-HOT WATER CALCULATION-SHOP BUILDING #5006  

SciTech Connect

The purpose of this design analysis and calculation is to determine the demand for domestic cold water and to size the supply main for the Shop Building No.5006 in accordance with the Uniform Plumbing Code (UPC) (Section 4.4.1) and the U.S. Department of Energy, Order 6430.1A-1540 (Section 4.4.2).

R. Blackstone

2006-01-25T23:59:59.000Z

64

Machine Tool Locator  

NLE Websites -- All DOE Office Websites (Extended Search)

gathered and used to set the position of the machine tool and to measure the size and shape of the machine tool tip, and examine cutting edge wear. April 18, 2013 machine tool...

65

Socially guided machine learning  

E-Print Network (OSTI)

Social interaction will be key to enabling robots and machines in general to learn new tasks from ordinary people (not experts in robotics or machine learning). Everyday people who need to teach their machines new things ...

Thomaz, Andrea Lockerd

2006-01-01T23:59:59.000Z

66

An Effective Optimization-Based Algorithm for Job Shop Scheduling with Fixed-Size Transfer Lots  

E-Print Network (OSTI)

Effective scheduling of production lots is of great importance for manufacturing medium to high-volume products that require significant setup times. Compared to traditional entire-lot production, lot splitting techniques divide a production lot into multiple smaller sublots so that each sublot can be "transferred" from one stage of operation to the next as soon as it has been completed. "Transfer lots," therefore, significantly reduce lead times and lower work-in-process (WIP) inventory. The mathematical modeling, analysis, and control of transfer lots, however, is extremely difficult. This paper presents a novel integer programming formulation with separable structure for scheduling job shops with fixed-size transfer lots. A solution methodology based on a synergistic combination of Lagrangian relaxation, backward dynamic programming (BDP), and heuristics is developed. Through explicit modeling of lot dynamics, transfer lots are handled on standard machines, machines with setups, and machines requiring all transfer lots within a production lot to be processed simultaneously. With "substates" and the derivation of DP functional equations considering transfer lot dynamics, the standard BDP is extended to solve the lot-level subproblems. The recently developed "time step reduction technique" is also used for increased efficiency. It implicitly establishes two time scales to reduce computational requirements without much loss of modeling accuracy and scheduling performance, thus enabling resolution of long-horizon problems within controllable computational requirements. The method has been implemented using object-oriented programming language C++, and numerical tests show that high-quality schedules involving transfer lots are efficiently generated to achieve on-time delivery of products with low WIP inventory.

Bin Jin; Peter B. Luh; L.S. Thakur

1999-01-01T23:59:59.000Z

67

VEE-0084 - In the Matter of Gas'n Shop, Inc. | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

84 - In the Matter of Gas'n Shop, Inc. 84 - In the Matter of Gas'n Shop, Inc. VEE-0084 - In the Matter of Gas'n Shop, Inc. On March 26, 2002, Gas'n Shop, Inc. (Gas'n Shop) of Lincoln, Nebraska filed an Application for Exception with the Office of Hearings and Appeals (OHA) of the Department of Energy (DOE). In its application, Gas'n Shop requests that it be excused from filing the Energy Information Administration's (EIA) form entitled "Resellers'/ Retailers' Monthly Petroleum Product Sales Report" (Form EIA-782B). For the reasons detailed below, we deny Gas'n Shop's request for exception relief. vee0084.pdf More Documents & Publications VEE-0082 - In the Matter of Fleischli Oil Company VEE-0081 - In the Matter of North Side Coal & Oil Co., Inc. VEE-0026 - In the Matter of R.W. Hays Co.

68

Machines reviving humans  

NLE Websites -- All DOE Office Websites (Extended Search)

The machines you may be referring to include machines to electrically stimulate the heart into again having a normal sequence of electrical impulses necessary for sustained...

69

CX-006388: Categorical Exclusion Determination | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

88: Categorical Exclusion Determination 88: Categorical Exclusion Determination CX-006388: Categorical Exclusion Determination Installation of Water Jet Cutter into 210-S Machine Shop CX(s) Applied: B1.3 Date: 06/08/2011 Location(s): Aiken, South Carolina Office(s): Environmental Management, Savannah River Operations Office Maintenance purchased and wishes to install a water jet cutter inside the 210-S machine shop. The water jet cutter will have electrical, water and air services run to it. The proposed activity has the water jets' outflow draining into the floor drain located in the maintenance shop weld cell. From there it will ultimately reach Central Sanitary Wastewater Treatment Facility (CSWTF) for disposition. DOCUMENT(S) AVAILABLE FOR DOWNLOAD CX-006388.pdf More Documents & Publications

70

Survey of Gas Turbine Component Repair Shops - 2008 Update  

Science Conference Proceedings (OSTI)

Aftermarket repair services for gas turbine O&M has been undergoing continual transformation beginning with the emergence of independent shops in the 1980s. The original equipment manufacturers (OEMs) began to aggressively pursue repair services in the late 1990s. Gas turbine hot section component repair/replacement coupled with inspection/overhaul technical support has come to be known broadly as long-term service agreements (LTSAs). These agreements often extend from 6 to 18 years. The repair business ...

2009-03-17T23:59:59.000Z

71

Clean iron production and machining technology. Year 1 summary report, January 1--December 31, 1995  

SciTech Connect

The first phase of this project was conducted to develop a technique for evaluating the machinability of gray and ductile iron. That technique was then used to measure the machinability of a variety of irons and determine the processing factors that influenced and controlled machinability. The procedure developed to evaluate machinability involved drilling holes with a feed rate of 0.009 in/rev at various surface speeds. High speed steel drills were used so wear was observed more quickly. Microcarbides present in the irons were found to dominate the machinability. Pearlitic irons considered to have ``acceptable`` machinability (indicated either by tool life measured in the laboratory using high speed steel (HSS) drills or reports from commercial machine shops using other cutters) were found to contain from 8.9 to 10.5% by weight microscopic carbides. The tool wear rate increased when machining at higher surface speeds or machining irons containing higher weight percentage of microcarbides. All irons containing above 11.5% microcarbides consistently exhibited poor machinability. Tool wear results obtained using cubic boron nitride (CBN) cutters paralleled those obtained with HSS. Higher iron microcarbide concentrations produced faster tool wear. Experiments are now being formulated to explore methods of improving iron machinability. Future work will extend the study to ductile irons.

1996-03-05T23:59:59.000Z

72

Action Memorandum for Decommissioning of TAN-607 Hot Shop Area  

DOE Green Energy (OSTI)

The Department of Energy is documenting the selection of an alternative for the TAN-607 Hot Shop Area using a Comprehensive Environmental Response, Compensation, and Liability Act non-time-critical removal action (NTCRA). The scope of the removal action is limited to TAN-607 Hot Shop Area. An engineering evaluation/cost analysis (EE/CA) has assisted the Department of Energy Idaho Operations Office in identifuomg the most effective method for performing the decommissioning of this structure whose mission has ended. TAN-607 Hot Shop Area is located at Test Area North Technical Support Facility within the Idaho National Laboratory Site. The selected alternative consists of demolishing the TAN-607 aboveground structures and components, removing belowground noninert components (e.g. wood products), and removing the radiologically contaminated debris that does not meet remedial action objectives (RAOs), as defined in the Record of Decision Amendment for the V-Tanks and Explanation of Significant Differences for the PM-2A Tanks at Test Area North, Operable Unit 1-10.

M. A. Pinzel

2007-05-01T23:59:59.000Z

73

Vehicle Technologies Office: Electrical Machines  

NLE Websites -- All DOE Office Websites (Extended Search)

Electrical Machines to Electrical Machines to someone by E-mail Share Vehicle Technologies Office: Electrical Machines on Facebook Tweet about Vehicle Technologies Office: Electrical Machines on Twitter Bookmark Vehicle Technologies Office: Electrical Machines on Google Bookmark Vehicle Technologies Office: Electrical Machines on Delicious Rank Vehicle Technologies Office: Electrical Machines on Digg Find More places to share Vehicle Technologies Office: Electrical Machines on AddThis.com... Just the Basics Hybrid & Vehicle Systems Energy Storage Advanced Power Electronics & Electrical Machines Power Electronics Electrical Machines Thermal Control & System Integration Advanced Combustion Engines Fuels & Lubricants Materials Technologies Electrical Machines Emphasis in the electrical machines activity is on advanced motor

74

Thanks, George Washington, for the Energy Efficient Washing Machine! |  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Thanks, George Washington, for the Energy Efficient Washing Thanks, George Washington, for the Energy Efficient Washing Machine! Thanks, George Washington, for the Energy Efficient Washing Machine! February 20, 2012 - 5:00am Addthis Kristin Swineford Communication Specialist, Weatherization and Intergovernmental Programs For many of us, particularly those living east of the Mississippi river, President's Day weekend is not just a time to honor the birthday of our country's founding father, it's also the final escape from dreadfully cold and snowy days. However, those of us with pestering consumerist habits to feed always ensure our return to the metropolis by Monday, as the day is quickly taking on a new reputation: Second best shopping day of the year, after Black Friday. By now you're asking, "What does any of this have to do with energy

75

Thanks, George Washington, for the Energy Efficient Washing Machine! |  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Thanks, George Washington, for the Energy Efficient Washing Thanks, George Washington, for the Energy Efficient Washing Machine! Thanks, George Washington, for the Energy Efficient Washing Machine! February 20, 2012 - 5:00am Addthis Kristin Swineford Communication Specialist, Weatherization and Intergovernmental Programs For many of us, particularly those living east of the Mississippi river, President's Day weekend is not just a time to honor the birthday of our country's founding father, it's also the final escape from dreadfully cold and snowy days. However, those of us with pestering consumerist habits to feed always ensure our return to the metropolis by Monday, as the day is quickly taking on a new reputation: Second best shopping day of the year, after Black Friday. By now you're asking, "What does any of this have to do with energy

76

Ubira: a mobile platform for an integrated online/offline shopping experience  

Science Conference Proceedings (OSTI)

Recently, mobile applications focusing on barcode scanning and price comparison are gaining popularity among users. The users of these applications are drawn away from participating in the business model of the brick-and-mortar stores. Ubira is a novel ... Keywords: brick-and-mortar stores, context-aware services, online and offline shopping integration, real world shopping, retailers, service model

Udana Bandara; James Chen

2011-09-01T23:59:59.000Z

77

A hybrid genetic tabu search algorithm for solving job shop scheduling problems: a case study  

Science Conference Proceedings (OSTI)

In recent decades many attempts have been made at the solution of Job Shop Scheduling Problem using a varied range of tools and techniques such as Branch and Bound at one end of the spectrum and Heuristics at the other end. However, the literature reviews ... Keywords: Genetic algorithms, Hybrid systems, Job shop, Scheduling, Tabu search

S. Meeran; M. S. Morshed

2012-08-01T23:59:59.000Z

78

A hybrid harmony search algorithm for the blocking permutation flow shop scheduling problem  

Science Conference Proceedings (OSTI)

This paper proposes a hybrid modified global-best harmony search (hmgHS) algorithm for solving the blocking permutation flow shop scheduling problem with the makespan criterion. First of all, the largest position value (LPV) rule is proposed to convert ... Keywords: Blocking flow shop, Harmony search, Metaheuristics, NEH heuristic, Tabu Search

Ling Wang; Quan-Ke Pan; M. Fatih Tasgetiren

2011-08-01T23:59:59.000Z

79

Solving the job-shop scheduling problem optimally by dynamic programming  

Science Conference Proceedings (OSTI)

Scheduling problems received substantial attention during the last decennia. The job-shop problem is a very important scheduling problem, which is NP-hard in the strong sense and with well-known benchmark instances of relatively small size which attest ... Keywords: Complexity analysis, Dynamic programming, Job-shop scheduling

Joaquim A. S. Gromicho; Jelke J. Van Hoorn; Francisco Saldanha-Da-Gama; Gerrit T. Timmer

2012-12-01T23:59:59.000Z

80

Mining customer knowledge to implement online shopping and home delivery for hypermarkets  

Science Conference Proceedings (OSTI)

With advances in modern technology, the Internet population has increased year by year globally. For young customers who consider convenience and speed as prerequisites, online shopping has become a new type of consumption. In addition, business-to-customer ... Keywords: Association rule, Cluster analysis, Data mining, Database marketing, Electronic commerce, Home delivery, On-line shopping

Shu-hsien Liao; Yin-ju Chen; Yi-tsun Lin

2011-04-01T23:59:59.000Z

Note: This page contains sample records for the topic "210-s machine shop" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


81

Sams Teach Yourself Paint Shop Pro 6 in 24 Hours, 1st edition  

Science Conference Proceedings (OSTI)

From the Publisher:This easily accessible tutorial uses a friendly, conversational approach to teach you the basics of Paint Shop Pro 6. With its careful, step-by-step approach, Sams Teach Yourself Paint Shop Pro 6 in 24 Hours makes it easy even for ...

T. Michael Clark; Michael Clark / Kris Tufto

1999-11-01T23:59:59.000Z

82

[Shopping Using the Product/Keyword Search] Updated March 15, 2012  

E-Print Network (OSTI)

Search returns products from the hosted catalogs. Start with by entering an item into the search field/Shop tab at the top to start your search 1. Shop at the Top To start searching for an item, enter the item in the search field ­ include specific search terms, such as "latex-free gloves" instead of just "gloves". New

Choate, Paul M.

83

From Shop Floor to Top Floor: Best Business Practices in Energy Efficiency  

Open Energy Info (EERE)

From Shop Floor to Top Floor: Best Business Practices in Energy Efficiency From Shop Floor to Top Floor: Best Business Practices in Energy Efficiency Jump to: navigation, search Tool Summary LAUNCH TOOL Name: From Shop Floor to Top Floor: Best Business Practices in Energy Efficiency Agency/Company /Organization: Pew Center on Global Climate Change Sector: Energy Focus Area: Energy Efficiency Topics: Policies/deployment programs Resource Type: Lessons learned/best practices Website: www.pewclimate.org/docUploads/PEW_EnergyEfficiency_FullReport.pdf References: From Shop Floor to Top Floor: Best Business Practices in Energy Efficiency[1] FROM SHOP FLOOR TO TOP FLOOR: BEST BUSINESS PRACTICES IN ENERGY EFFICIENCY. Pew Center on Global Climate Change. William R. Prindle. April 2010. In the last decade, rising and volatile energy prices coupled with

84

Science shops: A kaleidoscope of science-society collaborations in Europe  

E-Print Network (OSTI)

The science-shop model was initiated in the Netherlands in the 1970s. During the 1980s, the model spread throughout Europe, but without much coordination. The crucial idea behind the science shops involves a working relationship between knowledge-producing institutions like universities and citizen groups that need answers to relevant questions. More recently, the European Commission has funded a number of projects for taking stock of the results of science shops. Twenty-one in-depth case studies by seven science shops across Europe enable us to draw some conclusions about the variety of experiences in terms of differences among disciplines, nations, and formats of the historical institutionalization. The functions of science shops in the mediation of normative concerns with analytical perspectives can further be specified.

Leydesdorff, Loet

2009-01-01T23:59:59.000Z

85

Energy Savers: The One-Stop Shop for Energy Efficiency  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Savers: The One-Stop Savers: The One-Stop Shop for Energy Efficiency Building America Stakeholder Meeting Austin, TX Jayne Choi, Energy Analyst, CNT Energy March 1, 2012 CNT Center for Neighborhood Technology 33 year-old not-for-profit: 100 employees 2009 MacArthur Award Recipient Four issue areas: - Water - Transportation & community development - Climate - Energy Two affiliates: - CNT Energy - I-GO Car Sharing CNT Energy A division of the Center for Neighborhood Technology dedicated to helping communities and consumers save energy and money with: Dynamic Pricing and Smart Grid - Ameren Power Smart Pricing - ComEd Residential Real-Time Pricing Energy Efficient Buildings - Residential - Commercial and municipal buildings Regional Energy Planning - Sustainability plans for municipalities

86

finite state machine  

Science Conference Proceedings (OSTI)

... Moore machine), multiple start states, transitions conditioned on no input symbol (a null) or more than one transition for a given symbol and state ( ...

2013-11-08T23:59:59.000Z

87

Stirling machine operating experience  

Science Conference Proceedings (OSTI)

Numerous Stirling machines have been built and operated, but the operating experience of these machines is not well known. It is important to examine this operating experience in detail, because it largely substantiates the claim that stirling machines are capable of reliable and lengthy operating lives. The amount of data that exists is impressive, considering that many of the machines that have been built are developmental machines intended to show proof of concept, and are not expected to operate for lengthy periods of time. Some Stirling machines (typically free-piston machines) achieve long life through non-contact bearings, while other Stirling machines (typically kinematic) have achieved long operating lives through regular seal and bearing replacements. In addition to engine and system testing, life testing of critical components is also considered. The record in this paper is not complete, due to the reluctance of some organizations to release operational data and because several organizations were not contacted. The authors intend to repeat this assessment in three years, hoping for even greater participation.

Ross, B. [Stirling Technology Co., Richland, WA (United States); Dudenhoefer, J.E. [Lewis Research Center, Cleveland, OH (United States)

1994-09-01T23:59:59.000Z

88

Biomass Company Sets Up Shop in High School Lab | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Biomass Company Sets Up Shop in High School Lab Biomass Company Sets Up Shop in High School Lab Biomass Company Sets Up Shop in High School Lab March 30, 2010 - 2:45pm Addthis Stephen Graff Former Writer & editor for Energy Empowers, EERE Unlike most biotechnology students who have to go to a research facility to see scientists in action, those at Greeneville High just need to turn their heads. For the last four years, Larry Cosenza, of C2 Biotechnologies, a one-man shop in Germantown, N.Y, has been working in his basement to construct fusion enzymes, a new technology that converts biomass into energy more easily. But in January, he took over Greeneville High School's agriculture room, a move that will not only expand his workspace and put him steps closer to commercialization but also encourage project-based

89

Solving job-shop scheduling problems by a novel artificial immune system  

Science Conference Proceedings (OSTI)

The optimization of job-shop scheduling is very important because of its theoretical and practical significance. This paper proposes an efficient scheduling method based on artificial immune systems. In the proposed method, the initial population is ...

Hong-Wei Ge; Liang Sun; Yan-Chun Liang

2005-12-01T23:59:59.000Z

90

A multi-objective genetic algorithm for fuzzy flexible job-shop scheduling problem  

Science Conference Proceedings (OSTI)

In many real-world applications, processing times may vary dynamically due to human factors or operating faults and there are some other uncertain factors in the scheduling problems. Flexible job-shop scheduling problem (FJSP) is an extended traditional ...

Xiaojuan Wang; Liang Gao; Chaoyong Zhang; Xinyu Li

2012-12-01T23:59:59.000Z

91

Vehicle Technologies Office: Electrical Machines  

NLE Websites -- All DOE Office Websites (Extended Search)

Electrical Machines Emphasis in the electrical machines activity is on advanced motor technologies, performance, low-cost materials, and thermal control systems that will yield...

92

Human-machine interactions  

DOE Patents (OSTI)

Digital technology utilizing a cognitive model based on human naturalistic decision-making processes, including pattern recognition and episodic memory, can reduce the dependency of human-machine interactions on the abilities of a human user and can enable a machine to more closely emulate human-like responses. Such a cognitive model can enable digital technology to use cognitive capacities fundamental to human-like communication and cooperation to interact with humans.

Forsythe, J. Chris (Sandia Park, NM); Xavier, Patrick G. (Albuquerque, NM); Abbott, Robert G. (Albuquerque, NM); Brannon, Nathan G. (Albuquerque, NM); Bernard, Michael L. (Tijeras, NM); Speed, Ann E. (Albuquerque, NM)

2009-04-28T23:59:59.000Z

93

BCDA Machine Status Link  

NLE Websites -- All DOE Office Websites (Extended Search)

Machine Status Link Machine Status Link Version 1.33 (December 2005) David M. Kline. The Machine Status Link (MSL) is responsible for distributing the digitized beam current, injection status, P0 clock, and other statuses over a single fiber to several locations around the Storage Ring. The MRD100 is a VME-based module that is part of the MSL and was specifically designed for the APS. It receives and interprets information from the XMS100 module by means of copper or fiber. Signals from the XMS100 module are sent at a P0 rate (3.667 microseconds). It sends two registers every cycle and all in about 12 cycles. Refer to the ASD website for additional information regarding the MSL. The focus of this page is to provide information of how to configure the MRD100 for a beamline IOC and to discuss the sample IOC

94

Automated fiber pigtailing machine  

DOE Patents (OSTI)

The Automated Fiber Pigtailing Machine (AFPM) aligns and attaches optical fibers to optoelectronic (OE) devices such as laser diodes, photodiodes, and waveguide devices without operator intervention. The so-called pigtailing process is completed with sub-micron accuracies in less than 3 minutes. The AFPM operates unattended for one hour, is modular in design and is compatible with a mass production manufacturing environment. This machine can be used to build components which are used in military aircraft navigation systems, computer systems, communications systems and in the construction of diagnostics and experimental systems. 26 figs.

Strand, O.T.; Lowry, M.E.

1999-01-05T23:59:59.000Z

95

How Will You Shop for Your Next Vehicle? | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

How Will You Shop for Your Next Vehicle? How Will You Shop for Your Next Vehicle? How Will You Shop for Your Next Vehicle? July 28, 2011 - 11:41am Addthis On Monday, Shannon talked about how she's been using the online tools from the Advanced Technology Vehicle Data Center (AFDC) to help her decide what type of highly efficient vehicle may be best for her household. The AFDC provides excellent information such as a Light Duty Vehicle Search, an Alternative Fueling Station Locator, and a Hybrid and Plug-in Electric Vehicles section. All of these are helpful if you're wondering what type of vehicle can fit your needs while using the least possible amount of gasoline. In June, Eric's post Driving Home to a Clean Energy Future shared the latest in gasoline, electric, and hybrid vehicle labels. How about you? Are you starting to research vehicles, and if so, what tools

96

New Lighting Facts Label: Takes the Guess Work Out of Shopping for Light  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Lighting Facts Label: Takes the Guess Work Out of Shopping for Lighting Facts Label: Takes the Guess Work Out of Shopping for Light Bulbs New Lighting Facts Label: Takes the Guess Work Out of Shopping for Light Bulbs January 25, 2012 - 5:52am Addthis Chris Stewart Senior Communicator at DOE's National Renewable Energy Laboratory If you're like me, it sometimes feels overwhelming standing at the store and staring at a big wall of light bulbs, trying to understand all the lighting choices. With new lighting standards taking effect this year, now's a great time switch to energy-saving incandescent, CFL, and LED light bulbs, which are available in most hardware and home improvement retailers. They all are more energy-efficient than traditional incandescent bulbs, and upgrading 15 of the inefficient incandescent light bulbs in your home could

97

Operating the Lisp Machine  

E-Print Network (OSTI)

This document is a draft copy of a portion of the Lisp Machine window system manual. It is being published in this form now to make it available, since the complete window system manual is unlikely to be finished in the ...

Moon, David A.

98

Scalable formal machine models  

Science Conference Proceedings (OSTI)

In the past few years, we have seen machine-checked proofs of relatively large software systems, including compilers and micro-kernels. But like all formal arguments, the assurance gained by these mechanical proofs is only as good as the models we construct ...

Greg Morrisett

2012-12-01T23:59:59.000Z

99

Laser machining of explosives  

DOE Patents (OSTI)

The invention consists of a method for machining (cutting, drilling, sculpting) of explosives (e.g., TNT, TATB, PETN, RDX, etc.). By using pulses of a duration in the range of 5 femtoseconds to 50 picoseconds, extremely precise and rapid machining can be achieved with essentially no heat or shock affected zone. In this method, material is removed by a nonthermal mechanism. A combination of multiphoton and collisional ionization creates a critical density plasma in a time scale much shorter than electron kinetic energy is transferred to the lattice. The resulting plasma is far from thermal equilibrium. The material is in essence converted from its initial solid-state directly into a fully ionized plasma on a time scale too short for thermal equilibrium to be established with the lattice. As a result, there is negligible heat conduction beyond the region removed resulting in negligible thermal stress or shock to the material beyond a few microns from the laser machined surface. Hydrodynamic expansion of the plasma eliminates the need for any ancillary techniques to remove material and produces extremely high quality machined surfaces. There is no detonation or deflagration of the explosive in the process and the material which is removed is rendered inert.

Perry, Michael D. (Livermore, CA); Stuart, Brent C. (Fremont, CA); Banks, Paul S. (Livermore, CA); Myers, Booth R. (Livermore, CA); Sefcik, Joseph A. (Tracy, CA)

2000-01-01T23:59:59.000Z

100

Logically Possible Machines  

Science Conference Proceedings (OSTI)

I use modal logic and transfinite set-theory to define metaphysical foundations for a general theory of computation. A possible universe is a certain kind of situation; a situation is a set of facts. An algorithm is a certain kind of inductively defined ... Keywords: convergence, fixed-point, infinite algorithm, infinite machine, infinite mind, limit, possible world, situation, super-Turing computer

Eric Steinhart

2002-05-01T23:59:59.000Z

Note: This page contains sample records for the topic "210-s machine shop" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


101

Remote foods shopping robot system in a supermarket Tetsuo TOMIZAWA, National Inst. of Advanced Industrial Science and Technology  

E-Print Network (OSTI)

with the integrated system. Key Words: Remote shopping, Foods handling, Human interface 1. [1] 2 Remote foods shopping robot system in a supermarket Tetsuo TOMIZAWA, National Inst as a teleoperated tool for accessing and manipulating remote objects. This system attempts to answer the challenge

Ohya, Akihisa

102

Pricing and promotion strategies of an online shop based on customer segmentation and multiple objective decision making  

Science Conference Proceedings (OSTI)

The advent of the Internet and web technologies has enabled the prosperity of virtual stores, which greatly reduce customers' search costs and retailers' overhead. However, the furious competition between online shops makes it difficult for them to generate ... Keywords: Bargaining, Customer relationship management, Multiple objective decision making, Online shop, Pricing, Promotion

C.-C. Henry Chan; Chi-Bin Cheng; Wen-Chen Hsien

2011-11-01T23:59:59.000Z

103

Coded output support vector machine  

Science Conference Proceedings (OSTI)

The authors propose a coded output support vector machine (COSVM) by introducing the idea of information coding to solve multi-class classification problems for large-scale datasets. The COSVM is built based on the support vector regression (SVR) machine ... Keywords: coded output, multi-class classification, number system, parallel implementation, support vector machine (SVM)

Tao Ye; Xuefeng Zhu

2012-07-01T23:59:59.000Z

104

Data envelopment analysis classification machine  

Science Conference Proceedings (OSTI)

This paper establishes the equivalent relationship between the data classification machine and the data envelopment analysis (DEA) model, and thus build up a DEA based classification machine. A data is characterized by a set of values. Without loss of ... Keywords: Classification machine, Data envelopment analysis, Preference cone

Hong Yan; Quanling Wei

2011-11-01T23:59:59.000Z

105

International Business Machines Corporation  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Business Machines Corporation Business Machines Corporation Thomas J. Watson Research Center 1101 Kitchawan Road, NY 10598 Office of the Assistant General Counsel for Technology Transfer and Intellectual Property U.S. Department of Energy 1000 Independence Ave, SW, Washington DC 20585 ATTN: TECHNOLOGY TRANSFER QUESTIONS Sent electronically to GC-62@hq.doe.gov RE: Questions Concerning Technology Transfer Practices at DOE Laboratories Federal Register, Vol. 73, No. 229 Dear Mr. Gottlieb: IBM Corporation appreciates the opportunity to provide comments in response to the Department of Energy notice of inquiry. DOE Laboratories are a fundamental resource to government, industry, academia and the economy as a whole. All can benefit from efficient contracting processes and

106

Dynamic production scheduling of job-shop operations on the IBM 704 data-processing equipment  

Science Conference Proceedings (OSTI)

First, let us explain what we mean by job-shop operations. In this case we are talking about our Jet Engine Department in the General Electric Company, Aircraft Gas Turbine Division. The Jet Engine Department is the step between the basic concept development ...

L. N. Caplan; V. L. Schatz

1959-03-01T23:59:59.000Z

107

The Influence of Information Control upon On-line Shopping Behavior  

Science Conference Proceedings (OSTI)

Previous studies have explored privacy instruments and disclosures as factors that affect on-line shopping intentions or attitudes. However, few have evaluated how information control affects this behavior. This paper draws on psychological and social ... Keywords: Cognitive Absorption, Information Control, Intrinsic Motivation, On-Line Behavior, Procedural Practice Justice

Milam Aiken; Jianfeng Wang; Linwu Gu; Kustim Wibowo

2011-01-01T23:59:59.000Z

108

Remote Shopping Robot System for Fresh Foods Method of handling foods  

E-Print Network (OSTI)

Remote Shopping Robot System for Fresh Foods ­ Method of handling foods ­ Tetsuo TOMIZAWA, Akihisa a mobile manipulator as a teleoperated tool for accessing and manipulating remote objects. A human uses the system to select and buy fresh foods of a super market from a remote location via the Internet. We

Ohya, Akihisa

109

Predictors of police investigation performance: An empirical study of Norwegian police as value shop  

Science Conference Proceedings (OSTI)

Problem-solving organizations such as hospitals, law firms, engineering enterprises, consulting firms, and law enforcement agencies share the same value configuration of a value shop. Rather than inbound and outbound logistics found in value chains, ... Keywords: Information systems, Knowledge management, Knowledge management technology stages, Knowledge sharing, Leadership roles, Occupational culture, Organizational culture, Survey research

Petter Gottschalk

2007-02-01T23:59:59.000Z

110

Improving Multi-agent Evolutionary Techniques with Local Search for Job Shop Scheduling Problem  

Science Conference Proceedings (OSTI)

Scheduling is the allocation of shared resources over time in order to perform a number of tasks. Job Shop Scheduling Problem (JSSP) is the most commonly encountered scheduling problem. A wide range of approaches have been proposed to solve it. In this ... Keywords: Genetic Algorithm, Particle Swarm Optimization, Multi-Agent System, Job Schop Scheduling

Ahmad Balid; Sonajharia Minz

2008-12-01T23:59:59.000Z

111

Exposure Evaluation for Benzene, Lead and Noise in Vehicle and Equipment Repair Shops  

SciTech Connect

An exposure assessment was performed at the equipment and vehicle maintenance repair shops operating at the U. S. Department of Energy Hanford site, in Richland, Washington. The maintenance shops repair and maintain vehicles and equipment used in support of the Hanford cleanup mission. There are three general mechanic shops and one auto body repair shop. The mechanics work on heavy equipment used in construction, cranes, commercial motor vehicles, passenger-type vehicles in addition to air compressors, generators, and farm equipment. Services include part fabrication, installation of equipment, repair and maintenance work in the engine compartment, and tire and brake services. Work performed at the auto body shop includes painting and surface preparation which involves applying body filler and sanding. 8-hour time-weighted-average samples were collected for benzene and noise exposure and task-based samples were collected for lead dust work activities involving painted metal surfaces. Benzene samples were obtained using 3M™ 3520 sampling badges and were analyzed for additional volatile organic compounds. These compounds were selected based on material safety data sheet information for the aerosol products used by the mechanics for each day of sampling. The compounds included acetone, ethyl ether, toluene, xylene, VM&P naphtha, methyl ethyl ketone, and trichloroethylene. Laboratory data for benzene, VM&P naphtha, methyl ethyl ketone and trichloroethylene were all below the reporting detection limit. Airborne concentrations for acetone, ethyl ether, toluene and xylene were all less than 10% of their occupational exposure limit. The task-based samples obtained for lead dusts were submitted for a metal scan analysis to identify other metals that might be present. Laboratory results for lead dusts were all below the reporting detection limit and airborne concentration for the other metals observed in the samples were less than 10% of the occupational exposure limit. Noise dosimetry sampling was performed on a random basis and was representative of the different work activities within the four shops. Twenty three percent of the noise samples exceeded the occupational exposure limit of 85 decibels for an 8-hour time-weightedaverage. Work activities where noise levels were higher included use of impact wrenches and grinding wheels.

Sweeney, Lynn C.

2013-04-10T23:59:59.000Z

112

Machine Learning for Global Optimization  

E-Print Network (OSTI)

approach for global optimization in which machine learning is used to predict ..... In Figure 1 we show the level curves of the 2–dimensional Rastrigin function.

113

Power Electronics and Electric Machines  

NLE Websites -- All DOE Office Websites (Extended Search)

PEEM Activities Application Power Electronics Electric Machines Traction Drive System Inverter & Boost Converter (if needed) MotorGenerator Vehicle Power Management Bi-directional...

114

A new hybrid multi-objective Pareto archive PSO algorithm for a bi-objective job shop scheduling problem  

Science Conference Proceedings (OSTI)

This paper presents a new mathematical model for a bi-objective job shop scheduling problem with sequence-dependent setup times and ready times that minimizes the weighted mean flow time (F@?"w) and total penalties of tardiness and earliness (E/T). Obtaining ... Keywords: Bi-objective job shop, Genetic operators, Pareto archive PSO, Ready time, Sequence-dependent setup times, VNS

R. Tavakkoli-Moghaddam; M. Azarkish; A. Sadeghnejad-Barkousaraie

2011-09-01T23:59:59.000Z

115

Energy Efficiency Can Be at the Top of Your Shopping List | Department of  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Efficiency Can Be at the Top of Your Shopping List Efficiency Can Be at the Top of Your Shopping List Energy Efficiency Can Be at the Top of Your Shopping List November 30, 2009 - 3:30pm Addthis Eric Barendsen Energy Technology Program Specialist, Office of Energy Efficiency and Renewable Energy I don't know about you, but about the last thing I want this year for the holidays is another mustard-yellow sweater. Sure, it's nice to have some extra-warm clothes stashed in the top drawer of the dresser this time of year, but I'm clearly maxed-out in the yellow department. Right around this time of year I start putting together my master list of gifts that I could actually use-you know, things my parents would never buy me unless I told them I needed them. Now, honestly, not all of what I want this year has to do with saving energy and money. I can't think of any

116

Energy Efficiency Can Be at the Top of Your Shopping List | Department of  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Energy Efficiency Can Be at the Top of Your Shopping List Energy Efficiency Can Be at the Top of Your Shopping List Energy Efficiency Can Be at the Top of Your Shopping List November 30, 2009 - 3:30pm Addthis Eric Barendsen Energy Technology Program Specialist, Office of Energy Efficiency and Renewable Energy I don't know about you, but about the last thing I want this year for the holidays is another mustard-yellow sweater. Sure, it's nice to have some extra-warm clothes stashed in the top drawer of the dresser this time of year, but I'm clearly maxed-out in the yellow department. Right around this time of year I start putting together my master list of gifts that I could actually use-you know, things my parents would never buy me unless I told them I needed them. Now, honestly, not all of what I want this year has to do with saving energy and money. I can't think of any

117

Cleaning of Free Machining Brass  

Science Conference Proceedings (OSTI)

We have investigated four brightening treatments proposed by two cleaning vendors for cleaning free machining brass. The experimental results showed that none of the proposed brightening treatments passed the swipe test. Thus, we maintain the recommendation of not using the brightening process in the cleaning of free machining brass for NIF application.

Shen, T

2005-12-29T23:59:59.000Z

118

Knowledge representation and machine translation  

Science Conference Proceedings (OSTI)

This paper describes a new knowledge representation called "frame knowledge representation-0" (FKR-0), and an experimental machine translation system named ATLAS/I which uses FKR-0.The purpose of FKR-0 is to stored information required for machine translation ...

Susumu Sawai; Hiromichi Fukushima; Masakatsu Sugimoto; Naoya Ukai

1982-07-01T23:59:59.000Z

119

MSc Design of Rotating Machines  

E-Print Network (OSTI)

design management and intellectual skills of communication in a group working environment. Focus on your interests The Machine Design specialism aims to provide students with a greater degree of training of stress analysis, machine dynamics, transmissions, computer aided engineering, and project management

120

Environmental constituents of Electrical Discharge Machining  

E-Print Network (OSTI)

Electrical Discharge Machining (EDM) is a non-traditional process that uses no mechanical forces to machine metals. It is extremely useful in machining hard materials. With the advantages EDM has to offer and its presence ...

Cho, Margaret H. (Margaret Hyunjoo), 1982-

2004-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "210-s machine shop" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


121

Machine Learning Benchmarks and Random Forest Regression  

E-Print Network (OSTI)

Machine Learning Benchmarks and Random Forest Regressionerror on a suite of benchmark datasets. As the basethe Machine Learning Benchmark Problems package; see http://

Segal, Mark R

2004-01-01T23:59:59.000Z

122

Free Machining Brasses with Minimized Lead Content  

Science Conference Proceedings (OSTI)

Abstract Scope, Article describes the role of lead in free machining brass and ... Similar legislative acts take care of lead content in free machined brass.

123

Ma'aden Open Mould Casting Machines  

Science Conference Proceedings (OSTI)

The paper will describe Ma'aden experience in ingot casting machines: commissioning and start-up, the challenges faced specially with De-molding machines, ...

124

Optimal Design of Electrical Machines: Mathematical Programming ...  

E-Print Network (OSTI)

for the same problem of the design of an electrical machine without slot. ... tion, inverse problem, design, electrical machine ..... trade-off situation arises.

125

Measurement Science for Smart Machine Tools  

Science Conference Proceedings (OSTI)

... ASME B5.59-2, "Information Technology for Machine Tools—Part 2: Data Specification for Properties of Machine tools for Milling and Turning,"and ...

2012-12-21T23:59:59.000Z

126

Akrong Machine Services | Open Energy Information  

Open Energy Info (EERE)

Machine Services Jump to: navigation, search Name Akron Machine Services Address 17 w. Rosewood Ave Place Akron, Ohio Zip 44301 Sector Carbon Product Manufacturing Phone...

127

Slide system for machine tools  

DOE Patents (OSTI)

The present invention relates to a machine tool which permits the machining of nonaxisymmetric surfaces on a workpiece while rotating the workpiece about a central axis of rotation. The machine tool comprises a conventional two-slide system (X-Y) with one of these slides being provided with a relatively short travel high-speed auxiliary slide which carries the material-removing tool. The auxiliary slide is synchronized with the spindle speed and the position of the other two slides and provides a high-speed reciprocating motion required for the displacement of the cutting tool for generating a nonaxisymmetric surface at a selected location on the workpiece.

Douglass, S.S.; Green, W.L.

1980-06-12T23:59:59.000Z

128

Recent advances in kernel machines  

Science Conference Proceedings (OSTI)

This talk will review recent advances in the kernel methods focusing on support vector machines (SVM) for pattern recognition. Topics discussed include the kernel design issue through the multi kernel approach and the optimization issue with emphasis ...

Stéphane Canu

2010-11-01T23:59:59.000Z

129

ASC_machines_cielo_2  

National Nuclear Security Administration (NNSA)

ASC 1 Top500 winners ASC supercomputers ASC future supercomputers Leading High-Performance Computing ASCI Red * First sustained teraFLOPS machine * 1 teraFLOPS * 1 TOP500 6...

130

Selective batch crushing in the coal-preparation shop at OAO NTMK  

Science Conference Proceedings (OSTI)

In September 2004, after reconstruction at OAO Nizhnetagil'skii Metallurgicheskii Kombinat (NTMK), blast furnace 6 went into operation for the production of vanadium from hot metal. At the startup of furnace 6, besides optimising its composition; it was decided to restore selective crushing of the coal batch using pneumatic and mechanical separation in the third unit of the coal preparation shop. Additional increase in the mechanical strength of coke by 1.5-2.0% was predicted with a 0.5-1.0% decrease in wear.

N.A. Berkutov; Yu.V. Stepanov; P.V. Shtark; L.A. Makhortova; N.K. Popova; D.A. Koshkarov; N.V. Tsarev [OAO Nizhnetagil'skii Metallurgicheskii Kombinat (NTMK)(Russian Federation)

2007-05-15T23:59:59.000Z

131

Direct Semantics of Extended State Machines  

E-Print Network (OSTI)

In this paper we present semantic profiles for UML 2 state machines, which are based directly upon the structure of a state machine model, without requiring flattening or other transformations on these models. The approach addresses many of the semantic problems identified for state machines, and provides a basis for semantic analysis and proof of behavioural compatibility between state machines. 1

K. Lano; D. Clark

2007-01-01T23:59:59.000Z

132

Optimization Online - Optimal Design of Electrical Machines ...  

E-Print Network (OSTI)

Jun 8, 2011 ... Optimal Design of Electrical Machines: Mathematical Programming ... Science and Engineering (Multidisciplinary Design Optimization ).

133

Blacksmith Shops  

NLE Websites -- All DOE Office Websites (Extended Search)

of Cain, and Zillah had a son, Tubal-cain, "an instructor of every artificer in brass and iron". He is the hero of an epic poem written during the 19th century by a Scot,...

134

Window shopping  

SciTech Connect

The author addresses the energy efficiency of windows and describes changes and new products available in this consumer information article. Experiments currently being done by Lawrence Berkeley Laboratory (LBL), Bonneville Power Authority and the Washington State Energy Office show that some of these superwindows collect more energy from the sun than they let escape from inside the home. One type of window in current production is the low-E (low-emissivity) and the IGUs (insulated glass units). Low-E techniques include glazing of the glass with various materials including polyester and metallic coatings. Other measures include filling the airspace in double pane windows with argon, aerogel or by creating a vacuum in the airspace. Another factor the author considers is ultraviolet light protection.

Best, D.

1990-03-01T23:59:59.000Z

135

Alpha Channeling in Mirror Machines  

SciTech Connect

Because of their engineering simplicity, high-?, and steady-state operation, mirror machines and related open-trap machines such as gas dynamic traps, are an attractive concept for achieving controlled nuclear fusion. In these open-trap machines, the confinement occurs by means of magnetic mirroring, without the magnetic field lines closing upon themselves within the region of particle confinement. Unfortunately, these concepts have not achieved to date very spectacular laboratory results, and their reactor prospects are dimmed by the prospect of a low Q-factor, the ratio of fusion power produced to auxiliary power. Nonetheless, because of its engineering promise, over the years numerous improvements have been proposed to enhance the reactor prospects of mirror fusion, such as tandem designs, end-plugging, and electric potential barriers.

Fisch N.J.

2005-10-19T23:59:59.000Z

136

Cooling system for rotating machine  

Science Conference Proceedings (OSTI)

An electrical machine comprising a rotor is presented. The electrical machine includes the rotor disposed on a rotatable shaft and defining a plurality of radial protrusions extending from the shaft up to a periphery of the rotor. The radial protrusions having cavities define a fluid path. A stationary shaft is disposed concentrically within the rotatable shaft wherein an annular space is formed between the stationary and rotatable shaft. A plurality of magnetic segments is disposed on the radial protrusions and the fluid path from within the stationary shaft into the annular space and extending through the cavities within the radial protrusions.

Gerstler, William Dwight (Niskayuna, NY); El-Refaie, Ayman Mohamed Fawzi (Niskayuna, NY); Lokhandwalla, Murtuza (Clifton Park, NY); Alexander, James Pellegrino (Ballston Lake, NY); Quirion, Owen Scott (Clifton Park, NY); Palafox, Pepe (Schenectady, NY); Shen, Xiaochun (Schenectady, NY); Salasoo, Lembit (Schenectady, NY)

2011-08-09T23:59:59.000Z

137

A New Approach to Abstract Machines - Introduction to the Theory of Configuration Machines  

E-Print Network (OSTI)

An abstract machine is a theoretical model designed to perform a rigorous study of computation. Such a model usually consists of configurations, instructions, programs, inputs and outputs for the machine. In this paper we formalize these notions as a very simple algebraic system, called a configuration machine. If an abstract machine is defined as a configuration machine consisting of primitive recursive functions then the functions computed by the machine are always recursive. The theory of configuration machines provides a useful tool to study universal machines.

Luo, Zhaohua

2010-01-01T23:59:59.000Z

138

CRM strategies for a small-sized online shopping mall based on association rules and sequential patterns  

Science Conference Proceedings (OSTI)

As dot-com bubble burst in 2002, an uncountable number of small-sized online shopping malls have emerged every day due to many good characteristics of online marketplace, including significantly reduced search costs and menu cost for products or services ... Keywords: Association rule, CRM strategy, Data mining, RFM, Sequential pattern

Beomsoo Shim; Keunho Choi; Yongmoo Suh

2012-07-01T23:59:59.000Z

139

Syntactic mismatches in machine translation  

Science Conference Proceedings (OSTI)

This paper addresses one of the central problems arising at the transfer stage in machine translation: syntactic mismatches, that is, mismatches between a source-language sentence structure and its equivalent target-language sentence structure. The level ... Keywords: Deep-syntactic structure, Meaning-Text Theory, Paraphrasing, Syntactic mismatch, Transfer

Igor Mel'?uk; Leo Wanner

2006-06-01T23:59:59.000Z

140

Machinable dissolved metal oxide superconductors  

DOE Patents (OSTI)

Powders of a metal oxide superconductor are mixed with sufficient amount (10--80 mol%) of In, Sn, and/or Al, to become nonbrittle, machinable. Preferred superconductors are YBa[sub 2]Cu[sub 3]O[sub 7[minus]x] and Bi-Sr-Ca-Cu-O compounds.

Chen, Chung-Hsuan.

1991-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "210-s machine shop" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


141

Arbitrary norm support vector machines  

Science Conference Proceedings (OSTI)

Support vector machines (SVM) are state-of-the-art classifiers. Typically L2-norm or L1-norm is adopted as a regularization term in SVMs, while other norm-based SVMs, for example, the L0-norm SVM or even the L?-norm ...

Kaizhu Huang; Danian Zheng; Irwin King; Michael R. Lyu

2009-02-01T23:59:59.000Z

142

Polar Warnings A Lifelike Machine  

E-Print Network (OSTI)

States conducted its last underground nuclear test in 1992 and turned to Los Alamos and the other weapons Certification without Testing LOS ALAMOS DELIVERS THE FIRST NUCLEAR TRIGGER IN 20 YEARS A Lifelike Machine laboratories for a new approach to ensuring the continued safety and reliability of its nuclear deterrent

143

Machinable dissolved metal oxide superconductors  

DOE Patents (OSTI)

Powders of a metal oxide superconductor are mixed with sufficient amount (10--80 mol%) of In, Sn, and/or Al, to become nonbrittle, machinable. Preferred superconductors are YBa{sub 2}Cu{sub 3}O{sub 7{minus}x} and Bi-Sr-Ca-Cu-O compounds.

Chen, Chung-Hsuan

1991-12-31T23:59:59.000Z

144

Human-Machine Function Allocation  

Science Conference Proceedings (OSTI)

Table 1   Human-machine function comparison...ability Comparatively slow and poor computers. Excellent and very rapid computers. Memory storage Poor short-term storage. Excellent long-term storage. Excellent short-term storage. Long-term storage very

145

Engineering Evaluation/Cost Analysis (EE/CA) for Decommissioning of TAN-607 Hot Shop Area  

SciTech Connect

Test Area North (TAN) -607, the Technical Support Facility, is located at the north end of the Idaho National Laboratory (INL) Site. U.S. Department of Energy Idaho Operations Office (DOE-ID) is proposing to decommission the northern section of the TAN-607 facility, hereinafter referred to as TAN-607 Hot Shop Area, under a Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA) non-time-critical removal action (NTCRA). Despite significant efforts by the United States (U.S.) Department of Energy (DOE) to secure new business, no future mission has been identified for the TAN-607 Hot Shop Area. Its disposition has been agreed to by the Idaho State Historical Preservation Office documented in the Memorandum of Agreement signed October 2005 and it is therefore considered a surplus facility. A key element in DOE's strategy for surplus facilities is decommissioning to the maximum extent possible to ensure risk and building footprint reduction and thereby eliminating operations and maintenance cost. In addition, the DOE's 2006 Strategic Plan is ''complete cleanup of the contaminated nuclear weapons manufacturing and testing sites across the United States. DOE is responsible for the risk reduction and cleanup of the environmental legacy of the Nation's nuclear weapons program, one of the largest, most diverse, and technically complex environmental programs in the world. The Department will successfully achieve this strategic goal by ensuring the safety of the DOE employees and U.S. citizens, acquiring the best resources to complete the complex tasks, and managing projects throughout the United States in the most efficient and effective manner.'' TAN-607 is designated as a historical Signature Property by DOE Headquarters Advisory Council on Historic Preservation and, as such, public participation is required to determine the final disposition of the facility. The decommissioning action will place the TAN-607 Hot Shop Area in a final configuration that will be protective of human health and the environment. Decommissioning the TAN-607 Hot Shop Area is consistent with the joint DOE and U.S. Environmental Protection Agency (EPA) Policy on Decommissioning of Department of Energy Facilities Under the Comprehensive Environmental Response, Compensation and Liability Act, which establishes the CERCLA NTCRA process as the preferred approach for decommissioning surplus DOE facilities. Under this policy, a NTCRA may be taken when DOE determines that the action will prevent, minimize, stabilize, or eliminate a risk to human health and/or the environment. When DOE determines that a CERCLA NTCRA is necessary, DOE is authorized to evaluate, select, and implement the removal action that DOE determines is most appropriate to address the potential risk posed by the release or threat of release. This action is taken in accordance with applicable authorities and in conjunction with EPA and the State of Idaho pursuant to Section 5.3 of the Federal Facility Agreement and Consent Order. In keeping with the joint policy, this engineering evaluation/cost analysis (EE/CA) was developed in accordance with CERCLA as amended by the ''Superfund Amendments and Reauthorization Act of 1986'' and in accordance with the ''National Oil and Hazardous Substances Pollution Contingency Plan.'' This EE/CA is consistent with the remedial action objectives (RAOs) of the Final Record of Decision, Test Area North, Operable Unit 1-10 and supports the overall remediation goals established through the Federal Facility Agreement and Consent Order for Waste Area Group 1. Waste Area Group 1 is located at TAN.

J. P. Floerke

2007-02-05T23:59:59.000Z

146

Analyzing the Performance of Scientific Applications with OpenSpeedShop  

Science Conference Proceedings (OSTI)

Open|SpeedShop (O|SS) is a comprehensive, open source, parallel performance analysis tool set that provides the most common performance analysis steps in a single environment. It can help application programmers to analyze, understand and optimize the performance of their codes. O|SS provides a wide range of performance experiments covering both sampling and tracing techniques. It works on sequential, MPI, and multithreaded codes without requiring source code modifications. The latter allows users an easy integration of O|SS into their application's workflow and runtime environment. This ensures a low learning curve and is essential for achieving a wide spread adoption of any performance tool set. O|SS, together with documentation and extensive tutorials, is available at http://www.openspeedshop.org/.

Schulz, M; Galarowicz, J; Maghrak, D; Hachfeld, W; Montoya, D; Cranford, S

2009-10-14T23:59:59.000Z

147

Engineering Evaluation/Cost Analysis (EE/CA) for Decommissioning of TAN-607 Hot Shop Area  

SciTech Connect

Test Area North (TAN) -607, the Technical Support Facility, is located at the north end of the Idaho National Laboratory (INL) Site. U.S. Department of Energy Idaho Operations Office (DOE-ID) is proposing to decommission the northern section of the TAN-607 facility, hereinafter referred to as TAN-607 Hot Shop Area, under a Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA) non-time-critical removal action (NTCRA). Despite significant efforts by the United States (U.S.) Department of Energy (DOE) to secure new business, no future mission has been identified for the TAN-607 Hot Shop Area. Its disposition has been agreed to by the Idaho State Historical Preservation Office documented in the Memorandum of Agreement signed October 2005 and it is therefore considered a surplus facility. A key element in DOE's strategy for surplus facilities is decommissioning to the maximum extent possible to ensure risk and building footprint reduction and thereby eliminating operations and maintenance cost. In addition, the DOE's 2006 Strategic Plan is ''complete cleanup of the contaminated nuclear weapons manufacturing and testing sites across the United States. DOE is responsible for the risk reduction and cleanup of the environmental legacy of the Nation's nuclear weapons program, one of the largest, most diverse, and technically complex environmental programs in the world. The Department will successfully achieve this strategic goal by ensuring the safety of the DOE employees and U.S. citizens, acquiring the best resources to complete the complex tasks, and managing projects throughout the United States in the most efficient and effective manner.'' TAN-607 is designated as a historical Signature Property by DOE Headquarters Advisory Council on Historic Preservation and, as such, public participation is required to determine the final disposition of the facility. The decommissioning action will place the TAN-607 Hot Shop Area in a final configuration that will be protective of human health and the environment. Decommissioning the TAN-607 Hot Shop Area is consistent with the joint DOE and U.S. Environmental Protection Agency (EPA) Policy on Decommissioning of Department of Energy Facilities Under the Comprehensive Environmental Response, Compensation and Liability Act, which establishes the CERCLA NTCRA process as the preferred approach for decommissioning surplus DOE facilities. Under this policy, a NTCRA may be taken when DOE determines that the action will prevent, minimize, stabilize, or eliminate a risk to human health and/or the environment. When DOE determines that a CERCLA NTCRA is necessary, DOE is authorized to evaluate, select, and implement the removal action that DOE determines is most appropriate to address the potential risk posed by the release or threat of release. This action is taken in accordance with applicable authorities and in conjunction with EPA and the State of Idaho pursuant to Section 5.3 of the Federal Facility Agreement and Consent Order. In keeping with the joint policy, this engineering evaluation/cost analysis (EE/CA) was developed in accordance with CERCLA as amended by the ''Superfund Amendments and Reauthorization Act of 1986'' and in accordance with the ''National Oil and Hazardous Substances Pollution Contingency Plan.'' This EE/CA is consistent with the remedial action objectives (RAOs) of the Final Record of Decision, Test Area North, Operable Unit 1-10 and supports the overall remediation goals established through the Federal Facility Agreement and Consent Order for Waste Area Group 1. Waste Area Group 1 is located at TAN.

J. P. Floerke

2007-02-05T23:59:59.000Z

148

Using linguistic knowledge in statistical machine translation  

E-Print Network (OSTI)

In this thesis, we present methods for using linguistically motivated information to enhance the performance of statistical machine translation (SMT). One of the advantages of the statistical approach to machine translation ...

Zbib, Rabih M. (Rabih Mohamed), 1974-

2010-01-01T23:59:59.000Z

149

Spatial Ontology in Factored Statistical Machine Translation  

Science Conference Proceedings (OSTI)

This paper presents a statistical phrase-based machine translation system which is enriched with semantic data coming from a spatial ontology. Paper presents the spatial ontology, how it is integrated in statistical machine translation system using factored ...

Raivis Skadi?š

2011-08-01T23:59:59.000Z

150

Integrated Inverter For Driving Multiple Electric Machines  

DOE Patents (OSTI)

An electric machine drive (50) has a plurality of inverters (50a, 50b) for controlling respective electric machines (57, 62), which may include a three-phase main traction machine (57) and two-phase accessory machines (62) in a hybrid or electric vehicle. The drive (50) has a common control section (53, 54) for controlling the plurality of inverters (50a, 50b) with only one microelectronic processor (54) for controlling the plurality of inverters (50a, 50b), only one gate driver circuit (53) for controlling conduction of semiconductor switches (S1-S10) in the plurality of inverters (50a, 50b), and also includes a common dc bus (70), a common dc bus filtering capacitor (C1) and a common dc bus voltage sensor (67). The electric machines (57, 62) may be synchronous machines, induction machines, or PM machines and may be operated in a motoring mode or a generating mode.

Su, Gui-Jia [Knoxville, TN; Hsu, John S [Oak Ridge, TN

2006-04-04T23:59:59.000Z

151

Case history study of total energy system at Western Mall Shopping Center, Sioux Falls, South Dakota  

SciTech Connect

Western Mall Total Energy Plant in Sioux Falls, South Dakota, serves an enclosed mall shopping center of 462,000 ft/sup 2/. The plant provides most of the mall and tenants with electricity, space-heating, and air-conditioning services from a natural gas-fueled engine-generator plant with hot water heat recovery, supplementary gas-fueled boiler, and absorption water chiller. Heating load served by the plant is calculated to be 15,000,000 Btu at -30/sup 0/F winter design condition with 70/sup 0/F space temperature. Maximum observed cooling load at 100/sup 0/F, 75/sup 0/ W.B. outdoor conditions is about 750 tons of refrigeration. Engine heat is recovered in a water system operated at 210 to 240/sup 0/F; an auxiliary scotch marine type, firetype gas-fueled boiler provides up to 14,000,000 Btu/h or supplementary heat. Energy customers have recently begun to exercise considerable control over their uses of electricity with more careful operation of lighting and appliances and with some replacement of illumination devices with more-efficient equipment. It is concluded that central heating and air-conditioning facilities provide the owner with an assured means for serving the shopping center, regardless of which energy source is most economical or least available. The hot and chilled water can be obtained from gas fuel as at present, from fuel oil, propane, all electric, or coal firing. Adapting the conversion equipment is difficult only for coal because of the space requirement for storage and handling that fuel. The power-generating capacity in place is an asset that should be used to serve the tenants because it reduces the public utility company need for expanded capacity. (MCW)

1977-11-01T23:59:59.000Z

152

Software Tackles Production Line Machine ?Cyclic Jitters?  

Science Conference Proceedings (OSTI)

Software Tackles Production Line Machine 'Cyclic ... products, even shutting down assembly lines. ... high-speed data transmission characteristics of ...

2011-07-18T23:59:59.000Z

153

Automated energy monitoring of machine tools  

E-Print Network (OSTI)

in the energy usage, such as increased total consumption fortotal energy use for the machine tool based on the usage

Vijayaraghavan, Athulan; Dornfeld, David

2010-01-01T23:59:59.000Z

154

Do Accelerating Turing Machines Compute the Uncomputable?  

Science Conference Proceedings (OSTI)

Accelerating Turing machines have attracted much attention in the last decade or so. They have been described as "the work-horse of hypercomputation" (Potgieter and Rosinger 2010: 853). But do they really compute beyond the "Turing limit"--e.g., compute ... Keywords: ATM paradox, Accelerating Turing machine, Epistemic embedding, External and internal computation, Halting problem, Hypercomputation, Ontology of computing, Supertask, Thompson lamp paradox, Turing-machine purism, Turing-machine realism

B. Jack Copeland; Oron Shagrir

2011-05-01T23:59:59.000Z

155

Method and apparatus for monitoring machine performance  

DOE Patents (OSTI)

Machine operating conditions can be monitored by analyzing, in either the time or frequency domain, the spectral components of the motor current. Changes in the electric background noise, induced by mechanical variations in the machine, are correlated to changes in the operating parameters of the machine.

Smith, Stephen F. (Loudon, TN); Castleberry, Kimberly N. (Harriman, TN)

1996-01-01T23:59:59.000Z

156

Hindi to Punjabi machine translation system  

Science Conference Proceedings (OSTI)

Hindi-Punjabi being closely related language pair (Goyal V. and Lehal G. S., 2008), Hybrid Machine Translation approach has been used for developing Hindi to Punjabi Machine Translation System. Non-availability of lexical resources, spelling variations ... Keywords: Hindi, Punjabi, closely related languages, computational linguistics, machine translation, natural language processing, translate Hindi to Punjabi

Vishal Goyal; Gurpreet Singh Lehal

2011-06-01T23:59:59.000Z

157

Nano-Machines Achieve Huge Mechanical Breakthrough  

E-Print Network (OSTI)

NANO TECH Nano-Machines Achieve Huge Mechanical Breakthrough Dublin, Ireland (SPX) Sep 08, 2005 that use molecular 'nano'-machines of this kind to help perform physical tasks. Nano-machines could also owners set to return to battered Orleans l Six dead, two missing after heavy rains hit Page 1 of 3Nano

Leigh, David A.

158

Machine learning in space: extending our reach  

Science Conference Proceedings (OSTI)

We introduce the challenge of using machine learning effectively in space applications and motivate the domain for future researchers. Machine learning can be used to enable greater autonomy to improve the duration, reliability, cost-effectiveness, and ... Keywords: Autonomy, Machine learning applications, Space missions

Amy Mcgovern; Kiri L. Wagstaff

2011-09-01T23:59:59.000Z

159

A first look at cellular machine-to-machine traffic: large scale measurement and characterization  

Science Conference Proceedings (OSTI)

Cellular network based Machine-to-Machine (M2M) communication is fast becoming a market-changing force for a wide spectrum of businesses and applications such as telematics, smart metering, point-of-sale terminals, and home security and automation systems. ... Keywords: cellular network, machine-to-machine traffic

Muhammad Zubair Shafiq; Lusheng Ji; Alex X. Liu; Jeffrey Pang; Jia Wang

2012-06-01T23:59:59.000Z

160

Machine-to-Machine Communications and Security Solution in Cellular Systems  

Science Conference Proceedings (OSTI)

This paper introduces an efficient machine-to-machine M2M communication model based on 4G cellular systems. M2M terminals are capable of establishing Ad Hoc clusters wherever they are close enough. It is also possible to extend the cellular coverage ... Keywords: 4G Network, Ad Hoc, Machine-To-Machine, Security, Terminals

Mahdy Saedy; Vahideh Mojtahed

2011-04-01T23:59:59.000Z

Note: This page contains sample records for the topic "210-s machine shop" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


161

A micro-machined resonator  

DOE Patents (OSTI)

This invention is comprised of a micro-machined resonator, typically quartz, with upper and lower micromachinable support members, or covers, having etched wells which may be lined with conductive electrode material, between the support members is a quartz resonator having an energy trapping quartz mesa capacitively coupled to the electrodes through a diaphragm; the quartz resonator is supported by either micro-machined cantilever springs or by thin layers extending over the surfaces of the support. If the diaphragm is rigid, clock applications are available, and if the diaphragm is resilient, then transducer applications can be achieved. Either the thin support layers or the conductive electrode material can be integral with the diaphragm. In any event, the covers are bonded to form a hermetic seal and the interior volume may be filled with a gas or may be evacuated. In addition, one or both of the covers may include oscillator and interface circuitry for the resonator.

Godshall, N.A.; Koehler, D.R.; Liang, A.Y.; Smith, B.K.

1991-12-31T23:59:59.000Z

162

Z Machine | National Nuclear Security Administration  

National Nuclear Security Administration (NNSA)

Z Machine | National Nuclear Security Administration Z Machine | National Nuclear Security Administration Our Mission Managing the Stockpile Preventing Proliferation Powering the Nuclear Navy Emergency Response Recapitalizing Our Infrastructure Continuing Management Reform Countering Nuclear Terrorism About Us Our Programs Our History Who We Are Our Leadership Our Locations Budget Our Operations Media Room Congressional Testimony Fact Sheets Newsletters Press Releases Speeches Events Social Media Video Gallery Photo Gallery NNSA Archive Federal Employment Apply for Our Jobs Our Jobs Working at NNSA Blog Z Machine Z Machine Home > About Us > Our Programs > Defense Programs > Office of Research, Development, Test, and Evaluation > Office of Inertial Confinement Fusion > Facilities > Z Machine Z Machine Z Machine Sandia National Laboratories

163

Machines  

Science Conference Proceedings (OSTI)

...are used to supply electrical energy for the welding operation. The transformer tap switch frequently is a rotary, eight-step, knife-type, fully enclosed locking switch, which provides convenient adjustment of the welding voltage to suit work

164

Nuclear Maintenance Applications Center: Guide for the Performance of OnSite and Vendor Shop Inspections of Electric Motors  

Science Conference Proceedings (OSTI)

The power industry is experiencing a loss of expertise as its workforce ages. Compounding the problem is that many plants find that there is limited time to train new workers. Periodically, station and corporate motor specialists are asked to perform inspections of on-site motors to maintain a level of equipment reliability or to perform inspections for customers at vendor motor shops. This report should prove valuable during visual inspections of electric motors.

2008-12-19T23:59:59.000Z

165

Experiments with the Dragon Machine  

Science Conference Proceedings (OSTI)

The basic characteristics of a self-sustaining chain reaction were demonstrated with the Chicago Pile in 1943, but it was not until early 1945 that sufficient enriched material became available to experimentally verify fast-neutron cross-sections and the kinetic characteristics of a nuclear chain reaction sustained with prompt neutrons alone. However, the demands of wartime and the rapid decline in effort following the cessation of hostilities often resulted in the failure to fully document the experiments or in the loss of documentation as personnel returned to civilian pursuits. When documented, the results were often highly classified. Even when eventually declassified, the data were often not approved for public release until years later.2 Even after declassification and approval for public release, the records are sometimes difficult to find. Through a fortuitous discovery, a set of handwritten notes by ''ORF July 1945'' entitled ''Dragon - Research with a Pulsed Fission Reactor'' was found by William L. Myers in an old storage safe at Pajarito Site of the Los Alamos National Laboratory3. Of course, ORF was identified as Otto R. Frisch. The document was attached to a page in a nondescript spiral bound notebook labeled ''494 Book'' that bore the signatures of Louis Slotin and P. Morrison. The notes also reference an ''Idea LS'' that can only be Louis Slotin. The discovery of the notes led to a search of Laboratory Archives, the negative files of the photo lab, and the Report Library for additional details of the experiments with the Dragon machine that were conducted between January and July 1945. The assembly machine and the experiments were carefully conceived and skillfully executed. The analyses--without the crutch of computers--display real insight into the characteristics of the nuclear chain reaction. The information presented here provides what is believed to be a complete collection of the original documentation of the observations made with the Dragon Machine in early 1945.

R.E. Malenfant

2005-08-12T23:59:59.000Z

166

Free-piston cutting machine  

DOE Patents (OSTI)

A cutting machine includes a gun barrel for receiving a projectile. A compression tube is disposed in flow communication with the barrel and includes a piston therein. A reservoir is disposed in flow communication with the tube and receives a first gas under pressure. A second gas fills the compression tube on a front face of the piston. And, the pressurized first gas is discharged into the tube on a back face of the piston to accelerate the piston through the tube for compressing the second gas, and in turn launching the projectile through the barrel to impact a workpiece.

Ciccarelli, Gaby (East Setauket, NY); Subudhi, Manomohan (East Setauket, NY); Hall, Robert E. (Port Jefferson, NY)

2000-01-01T23:59:59.000Z

167

Hypervelocity cutting machine and method  

DOE Patents (OSTI)

A method and machine are provided for cutting a workpiece such as concrete. A gun barrel is provided for repetitively loading projectiles therein and is supplied with a pressurized propellant from a storage tank. A thermal storage tank is disposed between the propellant storage tank and the gun barrel for repetitively receiving and heating propellant charges which are released in the gun barrel for repetitively firing projectiles therefrom toward the workpiece. In a preferred embodiment, hypervelocity of the projectiles is obtained for cutting the concrete workpiece by fracturing thereof. 10 figs.

Powell, J.R.; Reich, M.

1996-11-12T23:59:59.000Z

168

Hypervelocity cutting machine and method  

DOE Patents (OSTI)

A method and machine 14 are provided for cutting a workpiece 12 such as concrete. A gun barrel 16 is provided for repetitively loading projectiles 22 therein and is supplied with a pressurized propellant from a storage tank 28. A thermal storage tank 32,32A is disposed between the propellant storage tank 28 and the gun barrel 16 for repetitively receiving and heating propellant charges which are released in the gun barrel 16 for repetitively firing projectiles 22 therefrom toward the workpiece 12. In a preferred embodiment, hypervelocity of the projectiles 22 is obtained for cutting the concrete workpiece 12 by fracturing thereof.

Powell, James R. (Shoreham, NY); Reich, Morris (Queens, NY)

1996-11-12T23:59:59.000Z

169

Micro-machined calorimetric biosensors  

DOE Patents (OSTI)

A method and apparatus are provided for detecting and monitoring micro-volumetric enthalpic changes caused by molecular reactions. Micro-machining techniques are used to create very small thermally isolated masses incorporating temperature-sensitive circuitry. The thermally isolated masses are provided with a molecular layer or coating, and the temperature-sensitive circuitry provides an indication when the molecules of the coating are involved in an enthalpic reaction. The thermally isolated masses may be provided singly or in arrays and, in the latter case, the molecular coatings may differ to provide qualitative and/or quantitative assays of a substance.

Doktycz, Mitchel J. (Knoxville, TN); Britton, Jr., Charles L. (Alcoa, TN); Smith, Stephen F. (Loudon, TN); Oden, Patrick I. (Plano, TX); Bryan, William L. (Knoxville, TN); Moore, James A. (Powell, TN); Thundat, Thomas G. (Knoxville, TN); Warmack, Robert J. (Knoxville, TN)

2002-01-01T23:59:59.000Z

170

Machine and Beam Delivery Updates  

NLE Websites -- All DOE Office Websites (Extended Search)

MAchine and Beam delivery Updates FY13 MAchine and Beam delivery Updates FY13 Summary of Beam Delivery: FACET Summary Feb_15_22.pdf FACET Summary Feb_15_22.pdf FACET Summary Feb_23_Mar_1.pdf FACET Summary Feb_23_Mar_1.pdf FACET Summary Mar_2_8.pdf FACET Summary Mar_2_8.pdf FACET Summary Mar_9_15.pdf FACET Summary Mar_9_15.pdf FACET Summary Mar_16_22.pdf FACET Summary Mar_16_22.pdf FACET Summary Mar_23_29.pdf FACET Summary Mar_23_29.pdf FACET Summary Mar_30_Apr_5.pdf FACET Summary Mar_30_Apr_5.pdf FACET Summary Apr_6_12.pdf FACET Summary Apr_6_12.pdf FACET Summary Apr_27_May_3.pdf FACET Summary Apr_27_May_3.pdf FACET Summary May_4_10.pdf FACET Summary May_4_10.pdf Emittance Stability in Sector 2_31513.pdf Emittance Stability in Sector 2_31513.pdf FACET beam operations readiness with R56.pdf FACET beam operations readiness with R56.pdf (6/19/2013)

171

Micro-machined resonator oscillator  

DOE Patents (OSTI)

A micro-miniature resonator-oscillator is disclosed. Due to the miniaturization of the resonator-oscillator, oscillation frequencies of one MHz and higher are utilized. A thickness-mode quartz resonator housed in a micro-machined silicon package and operated as a telemetered sensor beacon'' that is, a digital, self-powered, remote, parameter measuring-transmitter in the FM-band. The resonator design uses trapped energy principles and temperature dependence methodology through crystal orientation control, with operation in the 20--100 MHz range. High volume batch-processing manufacturing is utilized, with package and resonator assembly at the wafer level. Unique design features include squeeze-film damping for robust vibration and shock performance, capacitive coupling through micro-machined diaphragms allowing resonator excitation at the package exterior, circuit integration and extremely small (0.1 in. square) dimensioning. A family of micro-miniature sensor beacons is also disclosed with widespread applications as bio-medical sensors, vehicle status monitors and high-volume animal identification and health sensors. The sensor family allows measurement of temperatures, chemicals, acceleration and pressure. A microphone and clock realization is also available. 21 figs.

Koehler, D.R.; Sniegowski, J.J.; Bivens, H.M.; Wessendorf, K.O.

1994-08-16T23:59:59.000Z

172

Micro-machined resonator oscillator  

DOE Patents (OSTI)

A micro-miniature resonator-oscillator is disclosed. Due to the miniaturization of the resonator-oscillator, oscillation frequencies of one MHz and higher are utilized. A thickness-mode quartz resonator housed in a micro-machined silicon package and operated as a "telemetered sensor beacon" that is, a digital, self-powered, remote, parameter measuring-transmitter in the FM-band. The resonator design uses trapped energy principles and temperature dependence methodology through crystal orientation control, with operation in the 20-100 MHz range. High volume batch-processing manufacturing is utilized, with package and resonator assembly at the wafer level. Unique design features include squeeze-film damping for robust vibration and shock performance, capacitive coupling through micro-machined diaphragms allowing resonator excitation at the package exterior, circuit integration and extremely small (0.1 in. square) dimensioning. A family of micro-miniature sensor beacons is also disclosed with widespread applications as bio-medical sensors, vehicle status monitors and high-volume animal identification and health sensors. The sensor family allows measurement of temperatures, chemicals, acceleration and pressure. A microphone and clock realization is also available.

Koehler, Dale R. (Albuquerque, NM); Sniegowski, Jeffry J. (Albuquerque, NM); Bivens, Hugh M. (Albuquerque, NM); Wessendorf, Kurt O. (Albuquerque, NM)

1994-01-01T23:59:59.000Z

173

Rapid Response Small Machining NNR Project 703025  

SciTech Connect

This project was an effort to develop a machining area for small sized parts that is capable of delivering product with a quick response time. This entailed focusing efforts on leaning out specific work cells that would result in overall improvement to the entire machining area. This effort involved securing the most efficient available technologies for these areas. In the end, this incorporated preparing the small machining area for transformation to a new facility.

Kanies, Tim

2008-12-05T23:59:59.000Z

174

Automated energy monitoring of machine tools  

E-Print Network (OSTI)

studies to correlate energy usage with the operations beinghas characterized machining energy usage solely based on theplanning, process energy usage was characterized solely by

Vijayaraghavan, Athulan; Dornfeld, David

2010-01-01T23:59:59.000Z

175

Single machine stochastic appointment sequencing and scheduling  

E-Print Network (OSTI)

linear combination of job waiting time, machine idle time, and overtime. .... Through straightforward but lengthy analysis we found finite values for M1 and M2.

176

High pressure water jet mining machine  

DOE Patents (OSTI)

A high pressure water jet mining machine for the longwall mining of coal is described. The machine is generally in the shape of a plowshare and is advanced in the direction in which the coal is cut. The machine has mounted thereon a plurality of nozzle modules each containing a high pressure water jet nozzle disposed to oscillate in a particular plane. The nozzle modules are oriented to cut in vertical and horizontal planes on the leading edge of the machine and the coal so cut is cleaved off by the wedge-shaped body.

Barker, Clark R. (Rolla, MO)

1981-05-05T23:59:59.000Z

177

6.685 Electric Machines, Fall 2003  

E-Print Network (OSTI)

Treatment of electromechanical transducers, rotating and linear electric machines. Lumped-parameter electromechanics of interaction. Development of device characteristics: energy conversion density, efficiency; and of ...

Kirtley, James L.

178

Automated energy monitoring of machine tools  

E-Print Network (OSTI)

Potential for Energy Consumption in Discrete Part Productionprocessing Reducing the energy consumption of machine toolsthis, monitoring of energy consumption patterns in the

Vijayaraghavan, Athulan; Dornfeld, David

2010-01-01T23:59:59.000Z

179

Tabu search heuristic for two-machine flowshop with batch processing machines  

Science Conference Proceedings (OSTI)

Batch processing machines are frequently encountered in many industrial environments. A batch processing machine is one which can process several jobs simultaneously as a batch. The processing time of a batch is equal to the largest processing time of ... Keywords: Batch processing machines, Flowshop, MILP model, Tabu search

Li-Man Liao; Ching-Jen Huang

2011-04-01T23:59:59.000Z

180

A two-stage stochastic programming model for the parallel machine scheduling problem with machine capacity  

Science Conference Proceedings (OSTI)

This paper proposes a two-stage stochastic programming model for the parallel machine scheduling problem where the objective is to determine the machines' capacities that maximize the expected net profit of on-time jobs when the due dates are uncertain. ... Keywords: Average sample approximation, Parallel machine scheduling, Ranking and selection, Stochastic programming, Weighted number of on-time jobs

Talal Al-Khamis; Rym M'Hallah

2011-12-01T23:59:59.000Z

Note: This page contains sample records for the topic "210-s machine shop" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


181

Nontraditional Machining of Dies and Molds  

Science Conference Proceedings (OSTI)

...instability (Ref 9, 10). When coupled with ultrafast controllers operating on 2 μs control loops and glass scales to directly measure the motion of the machines axes, linear motors enable EDM machines to react to process instabilities quickly, leading to increased process speed and decreased risk of...

182

Improving vehicle aeroacoustics using machine learning  

Science Conference Proceedings (OSTI)

This paper presents a new approach to improving the overall aeroacoustic comfort of a vehicle, an important feature of vehicle design. The traditional improvement process is extended to benefit extensively from machine learning, information retrieval ... Keywords: Aeroacoustics, Automobile industry, Machine learning, Noise frequency spectrum analysis, Process automation

Damjan Kunar; Martin Moina; Marina Giordanino; Ivan Bratko

2012-08-01T23:59:59.000Z

183

Quantum Cloning Machines and the Applications  

E-Print Network (OSTI)

No-cloning theorem is fundamental for quantum mechanics and for quantum information science that states an unknown quantum state cannot be cloned perfectly. However, we can try to clone a quantum state approximately with the optimal fidelity, or instead, we can try to clone it perfectly with the largest probability. Thus various quantum cloning machines have been designed for different quantum information protocols. Specifically, quantum cloning machines can be designed to analyze the security of quantum key distribution protocols such as BB84 protocol, six-state protocol, B92 protocol and their generalizations. Some well-known quantum cloning machines include universal quantum cloning machine, phase-covariant cloning machine, the asymmetric quantum cloning machine and the probabilistic quantum cloning machine etc. In the past years, much progress has been made in studying quantum cloning machines and their applications and implementations, both theoretically and experimentally. In this review, we will give a complete description of those important developments about quantum cloning and some related topics. On the other hand, this review is self-consistent, and in particular, we try to present some detailed formulations so that further study can be taken based on those results. In addition, this review also contains some new results, for example, the study of quantum retrodiction protocol.

Heng Fan; Yi-Nan Wang; Li Jing; Jie-Dong Yue; Han-Duo Shi; Yong-Liang Zhang; Liang-Zhu Mu

2013-01-14T23:59:59.000Z

184

Following directions using statistical machine translation  

Science Conference Proceedings (OSTI)

Mobile robots that interact with humans in an intuitive way must be able to follow directions provided by humans in unconstrained natural language. In this work we investigate how statistical machine translation techniques can be used to bridge the gap ... Keywords: human-robot interaction, instruction following, natural language, navigation, statistical machine translation

Cynthia Matuszek; Dieter Fox; Karl Koscher

2010-03-01T23:59:59.000Z

185

Bagging and Boosting statistical machine translation systems  

Science Conference Proceedings (OSTI)

In this article we address the issue of generating diversified translation systems from a single Statistical Machine Translation (SMT) engine for system combination. Unlike traditional approaches, we do not resort to multiple structurally different SMT ... Keywords: Ensemble learning, Statistical machine translation, System combination

Tong Xiao; Jingbo Zhu; Tongran Liu

2013-02-01T23:59:59.000Z

186

Comparison of crowdsourcing translation with Machine Translation  

Science Conference Proceedings (OSTI)

In this paper we examine the model of crowdsourcing for translation and compare it with Machine Translation (MT). The large volume of material to be translated, the translation of this material into many languages combined with tight deadlines lead enterprises ... Keywords: Machine Translation, crowdsourcing, empirical data, human translation, quality

Dimitra Anastasiou; Rajat Gupta

2011-12-01T23:59:59.000Z

187

Machine Translation Errors: English and Iraqi Arabic  

Science Conference Proceedings (OSTI)

Errors in machine translations of English-Iraqi Arabic dialogues were analyzed using the methods developed for the Human Translation Error Rate measure (HTER). Human annotations were used to refine the Translation Error Rate (TER) annotations. The analyses ... Keywords: Arabic, English, error analysis, evaluation, statistical machine translation

S. Condon; D. Parvaz; J. Aberdeen; C. Doran; A. Freeman; M. Awad

2011-03-01T23:59:59.000Z

188

A Machine Vision System for Inspecting Bearings  

Science Conference Proceedings (OSTI)

In this paper, we describe a machine vision system for inspecting bearings, which are an important part of electro-mechanical kWh meters. The system consists of a personal computer with a frame grabber, a black and white progressive scan CCD camera, ... Keywords: machine vision, quality control, bearing, eccentricity

2000-09-01T23:59:59.000Z

189

Using artificially generated data to evaluate statistical machine translation  

Science Conference Proceedings (OSTI)

Although Statistical Machine Translation (SMT) is now the dominant paradigm within Machine Translation, we argue that it is far from clear that it can outperform Rule-Based Machine Translation (RBMT) on small- to medium-vocabulary applications where ...

Manny Rayner; Paula Estrella; Pierrette Bouillon; Beth Ann Hockey; Yukie Nakao

2009-08-01T23:59:59.000Z

190

A hybrid type small 5-axis CNC milling machine  

E-Print Network (OSTI)

5-axis CNC milling machines are important in a number of industries ranging from aerospace to consumer-die-mold machining because they can deliver high machining accuracy with a spindle tilting capacity. Most of these ...

Son, Seung-Kil, 1964-

2002-01-01T23:59:59.000Z

191

ESH / QA  

NLE Websites -- All DOE Office Websites (Extended Search)

Advanced Photon Source (APS). APS Safety and Training Information ES&H Online Safety Manuals LOTO Menu User Machine Shop Information The User Machine Shops require individual...

192

DOE - Office of Legacy Management -- La Pointe Machine and Tool...  

Office of Legacy Management (LM)

La Pointe Machine and Tool Co - MA 16 FUSRAP Considered Sites Site: LA POINTE MACHINE AND TOOL CO. (MA.16 ) Eliminated from consideration under FUSRAP Designated Name: Not...

193

Electric machine for hybrid motor vehicle - Energy Innovation ...  

A power system for a motor vehicle having an internal combustion engine and an electric machine is disclosed. The electric machine has a stator, a permanent magnet ...

194

John Hsu, Oak Ridge National Laboratory, Flux Coupling Machines...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Flux Coupling Machines and Switched Reluctance Motors to Replace Permanent Magnets in Electric Vehicles John Hsu, Oak Ridge National Laboratory, Flux Coupling Machines and...

195

Hybrid MPI/OpenMP parallel support vector machine training  

E-Print Network (OSTI)

Jan 6, 2009 ... Support Vector Machines are a powerful machine learning technol- ..... to the precision recall curve were evaluated on the Challenge web-.

196

Multi-winding homopolar electric machine - Energy Innovation Portal  

A multi-winding homopolar electric machine and method for converting between mechanical energy and electrical energy. The electric machine includes a shaft defining ...

197

Ultraprecision machining of optics at Los Alamos  

Science Conference Proceedings (OSTI)

Ultraprecision machine tools are used at Los Alamos for single point diamond turning of optics and other precision parts. Measurements of a 50-mm-dia copper flat are used to illustrate the quality of a part which can be machined on the Moore No. 3 lathe. Measurements of a 0.4-m-dia aluminum mirror with a 20-m radius-of-curvature are presented as an example of a part machined on the Moore No. 5 lathe. A varying frequency sine wave grating is used to show a type of special optical grating which can be produced using the Pneumo lathe.

Rhorer, R.L.; Gauler, A.L.; Colston, E.W.; Ruhe, J.R.

1981-01-01T23:59:59.000Z

198

Electric machine for hybrid motor vehicle  

DOE Patents (OSTI)

A power system for a motor vehicle having an internal combustion engine and an electric machine is disclosed. The electric machine has a stator, a permanent magnet rotor, an uncluttered rotor spaced from the permanent magnet rotor, and at least one secondary core assembly. The power system also has a gearing arrangement for coupling the internal combustion engine to wheels on the vehicle thereby providing a means for the electric machine to both power assist and brake in relation to the output of the internal combustion engine.

Hsu, John Sheungchun (Oak Ridge, TN)

2007-09-18T23:59:59.000Z

199

An analysis of iterated local search for job-shop scheduling.  

Science Conference Proceedings (OSTI)

Iterated local search, or ILS, is among the most straightforward meta-heuristics for local search. ILS employs both small-step and large-step move operators. Search proceeds via iterative modifications to a single solution, in distinct alternating phases. In the first phase, local neighborhood search (typically greedy descent) is used in conjunction with the small-step operator to transform solutions into local optima. In the second phase, the large-step operator is applied to generate perturbations to the local optima obtained in the first phase. Ideally, when local neighborhood search is applied to the resulting solution, search will terminate at a different local optimum, i.e., the large-step perturbations should be sufficiently large to enable escape from the attractor basins of local optima. ILS has proven capable of delivering excellent performance on numerous N P-Hard optimization problems. [LMS03]. However, despite its implicity, very little is known about why ILS can be so effective, and under what conditions. The goal of this paper is to advance the state-of-the-art in the analysis of meta-heuristics, by providing answers to this research question. They focus on characterizing both the relationship between the structure of the underlying search space and ILS performance, and the dynamic behavior of ILS. The analysis proceeds in the context of the job-shop scheduling problem (JSP) [Tai94]. They begin by demonstrating that the attractor basins of local optima in the JSP are surprisingly weak, and can be escaped with high probaiblity by accepting a short random sequence of less-fit neighbors. this result is used to develop a new ILS algorithms for the JSP, I-JAR, whose performance is competitive with tabu search on difficult benchmark instances. They conclude by developing a very accurate behavioral model of I-JAR, which yields significant insights into the dynamics of search. The analysis is based on a set of 100 random 10 x 10 problem instances, in addition to some widely used benchmark instances. Both I-JAR and the tabu search algorithm they consider are based on the N1 move operator introduced by van Laarhoven et al. [vLAL92]. The N1 operator induces a connected search space, such that it is always possible to move from an arbitrary solution to an optimal solution; this property is integral to the development of a behavioral model of I-JAR. However, much of the analysis generalizes to other move operators, including that of Nowicki and Smutnick [NS96]. Finally the models are based on the distance between two solutions, which they take as the well-known disjunctive graph distance [MBK99].

Whitley, L. Darrell (Colorado State University, Fort Collins, CO); Howe, Adele E. (Colorado State University, Fort Collins, CO); Watson, Jean-Paul (Colorado State University, Fort Collins, CO)

2003-08-01T23:59:59.000Z

200

Machine Partitions | Argonne Leadership Computing Facility  

NLE Websites -- All DOE Office Websites (Extended Search)

BG/Q Drivers Status Machine Overview Machine Partitions Torus Network Data Storage & File Systems Compiling & Linking Queueing & Running Jobs Data Transfer Debugging & Profiling Performance Tools & APIs Software & Libraries IBM References Intrepid/Challenger/Surveyor Tukey Eureka / Gadzooks Policies Documentation Feedback Please provide feedback to help guide us as we continue to build documentation for our new computing resource. [Feedback Form] Machine Partitions Mira As our production machine, the queues on Mira are very similar to those on our BG/P system Intrepid. In the prod-capability queue, partition sizes of 8192, 12288, 16384, 32768, and 49152 nodes are available. All partitions have a full torus network. The max runtime of jobs submitted to the

Note: This page contains sample records for the topic "210-s machine shop" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


201

Computational aesthetic evaluation: steps towards machine creativity  

Science Conference Proceedings (OSTI)

Programmer and artists have invented a broad range of generative systems that create art and music. These powerful systems sometimes produce results that surprise their human collaborators, but the surprises are not always welcome or useful. Machine ...

Philip Galanter

2012-08-01T23:59:59.000Z

202

Machine Learning for Sequential Data: A Review  

Science Conference Proceedings (OSTI)

Statistical learning problems in many fields involve sequential data. This paper formalizes the principal learning tasks and describes the methods that have been developed within the machine learning research community for addressing these problems. ...

Thomas G. Dietterich

2002-08-01T23:59:59.000Z

203

CCG supertags in factored statistical machine translation  

Science Conference Proceedings (OSTI)

Combinatorial Categorial Grammar (CCG) supertags present phrase-based machine translation with an opportunity to access rich syntactic information at a word level. The challenge is incorporating this information into the translation process. Factored ...

Alexandra Birch; Miles Osborne; Philipp Koehn

2007-06-01T23:59:59.000Z

204

March 8, 2006: Sandia's Z Machine  

Energy.gov (U.S. Department of Energy (DOE))

March 8, 2006The Department's Sandia National Laboratories announces that its Z machine has produced plasmas that exceed temperatures of 2 billion degrees Kelvin-hotter than the interiors of stars....

205

An environment machine for the ??-calculus  

Science Conference Proceedings (OSTI)

We introduce a natural deduction-like formalisation of Parigot's ??-calculus. From this, we derive an environment machine that allows any well-typed ??-term to be reduced to its weak head normal form. The soundness and completeness ...

Philippe De Groote

1998-12-01T23:59:59.000Z

206

Machine translation system combination by confusion forest  

Science Conference Proceedings (OSTI)

The state-of-the-art system combination method for machine translation (MT) is based on confusion networks constructed by aligning hypotheses with regard to word similarities. We introduce a novel system combination framework in which hypotheses are ...

Taro Watanabe; Eiichiro Sumita

2011-06-01T23:59:59.000Z

207

A machine learning system for recognizing subclasses  

Science Conference Proceedings (OSTI)

Thematic information extraction from remote sensing images is a complex task. In this demonstration, we present *Miner machine learning system. In particular, we demonstrate an advanced subclass recognition algorithm that is specifically designed to ...

Ranga Raju Vatsavai

2012-07-01T23:59:59.000Z

208

Machine Status | Argonne Leadership Computing Facility  

NLE Websites -- All DOE Office Websites (Extended Search)

Machine Status Science on Mira Cores Core Hours Atomistic Simulations of Nanoscale Oxides and Oxide Interfaces 65536 1297201.9256901 Lattice QCD 16384 28881.396622179 MockBOSS :...

209

Revisiting parallel rendering for shared memory machines  

Science Conference Proceedings (OSTI)

Increasing the core count of CPUs to increase computational performance has been a significant trend for the better part of a decade. This has led to an unprecedented availability of large shared memory machines. Programming paradigms and systems are ...

B. Nouanesengsy; J. Ahrens; J. Woodring; H. Shen

2011-04-01T23:59:59.000Z

210

Virtualisation: Real security for virtual machines  

Science Conference Proceedings (OSTI)

Server virtualisation offers many real benefits to enterprises, maximising hardware resources and providing significant cost and energy savings. But there is a downside: all of the security issues we battle on networked systems also plague virtual machines, ...

Ulf Mattsson

2009-04-01T23:59:59.000Z

211

DESIGN FOR AN AUTOGRAPHICALLY RECORDING TENSILE MACHINE  

SciTech Connect

An improved "hard" type tensile machine is described, designed primarily for metallurgical usage. Compactness and mechanical simplicity are combined with maximum accessibility of the load measuring device and specimen, and the load is measured with an electro-mechanical dynamometer which is easily adapted into a system for autographically recording ihe load-elongaticn curve. The machine should be particularly useful for dry-box or hot-cell work. (auth)

Adams, M.A.

1959-10-01T23:59:59.000Z

212

Baseline Test Specimen Machining Report  

SciTech Connect

The Next Generation Nuclear Plant (NGNP) Project is tasked with selecting a high temperature gas reactor technology that will be capable of generating electricity and supplying large amounts of process heat. The NGNP is presently being designed as a helium-cooled high temperature gas reactor (HTGR) with a large graphite core. The graphite baseline characterization project is conducting the research and development (R&D) activities deemed necessary to fully qualify nuclear-grade graphite for use in the NGNP reactor. Establishing nonirradiated thermomechanical and thermophysical properties by characterizing lot-to-lot and billet-to-billet variations (for probabilistic baseline data needs) through extensive data collection and statistical analysis is one of the major fundamental objectives of the project. The reactor core will be made up of stacks of graphite moderator blocks. In order to gain a more comprehensive understanding of the varying characteristics in a wide range of suitable graphites, any of which can be classified as “nuclear grade,” an experimental program has been initiated to develop an extensive database of the baseline characteristics of numerous candidate graphites. Various factors known to affect the properties of graphite will be investigated, including specimen size, spatial location within a graphite billet, specimen orientation within a billet (either parallel to [P] or transverse to [T] the long axis of the as-produced billet), and billet-to-billet variations within a lot or across different production lots. Because each data point is based on a certain position within a given billet of graphite, particular attention must be paid to the traceability of each specimen and its spatial location and orientation within each billet. The evaluation of these properties is discussed in the Graphite Technology Development Plan (Windes et. al, 2007). One of the key components in the evaluation of these graphite types will be mechanical testing on specimens drawn from carefully controlled sections of each billet. To this end, this report will discuss the machining of the first set of test specimens that will be evaluated in this program through tensile, compressive, and flexural testing. Validation that the test specimens have been produced to the tolerances required by the applicable ASTM standards, and to the quality control levels required by this program, will demonstrate the viability of sending graphite to selected suppliers that will provide valuable and certifiable data to future data sets that are integral to the NGNP program and beyond.

mark Carroll

2009-08-01T23:59:59.000Z

213

Machine Maintenance Integrated Performance Support System  

SciTech Connect

The objectives of this partnership project were to develop a preventive maintenance checklist program, a troubleshooting system for the Vertical Turning Center (VTC)-5, an on-line manual, and to integrate these components with a custom browser that would run on the VTC-5 machine's controller and would support future internet/intranet delivery. Kingsbury provided subject matter experts from engineering, manufacturing, and technical support. They also provided photographs, schematics, and CAD drawings, which AlliedSignal Federal Manufacturing and Technologies (ASFM and T) digitized for use in the final program. Information from The Kingsbury troubleshooting experts were interviewed regarding symptoms and root causes of system malfunctions This knowledge was captured and from it, fault trees were developed. These trees were then incorporated into the EPSS as a troubleshooting tool. The troubleshooting portion of the system presents simple questions to the machine operator in order to determine the likely cause or causes of malfunctions and then recommends systematic corrective actions. The on-line reference manual, covering operations and maintenance, provides text and illustrations to the machine operator in a traditional structure, but additionally offers the capability to search voluminous amounts of technical data and retrieve specific information on request. The maintenance portion of the EPSS includes checklists that are displayed daily, weekly, monthly, and annually, as appropriate, on the VTC-5 controller screen. The controller software is unavailable for machining parts until the machine tool operator goes through and checks off all of the checklist items. This project provided the team with a detailed understanding of the knowledge and information required to produce and support advanced machine tools. In addition, it resulted in the design and construction of a prototype VTC-5 EPSS containing all the logic and interfaces necessary to integrate operations and maintenance information from other Kingsbury machine tools.

Bohley, M.C.; Schwartz, M.E.

1998-03-11T23:59:59.000Z

214

Digital clip gift shops as scenarios for collaborative architectures for monetising broadcast archive content: an evaluation from a technical and business viewpoint  

Science Conference Proceedings (OSTI)

Within the scope of this paper we focus on the investigation of potential scenarios for providing clips via common broadcasting platform for sharing these across social media. We develop the idea of a digital clip gift shop and present a technical solution ...

Sabine Bachmayer, Artur Lugmayr, Gabriele Kotsis

2013-05-01T23:59:59.000Z

215

International Conference on Machine Control & Guidance 2008 1 Automatic Guidance of Track Laying Machines with  

E-Print Network (OSTI)

laying machines, coordinate systems, error detection, work process driven data management, quality. Its outstanding result, the track management system Toporail, was developed under the operational lead on Machine Control & Guidance 2008 5 Figure 5: Maintenance process driven data management: Data updates

216

Trunnion Collar Removal Machine - Gap Analysis Table  

SciTech Connect

The purpose of this document is to review the existing the trunnion collar removal machine against the ''Nuclear Safety Design Bases for License Application'' (NSDB) [Ref. 10] requirements and to identify codes and standards and supplemental requirements to meet these requirements. If these codes and standards can not fully meet these requirements then a ''gap'' is identified. These gaps will be identified here and addressed using the ''Trunnion Collar Removal Machine Design Development Plan'' [Ref. 15]. The codes and standards, supplemental requirements, and design development requirements for the trunnion collar removal machine are provided in the gap analysis table (Appendix A, Table 1). Because the trunnion collar removal machine is credited with performing functions important to safety (ITS) in the NSDB [Ref. 10], design basis requirements are applicable to ensure equipment is available and performs required safety functions when needed. The gap analysis table is used to identify design objectives and provide a means to satisfy safety requirements. To ensure that the trunnion collar removal machine performs required safety functions and meets performance criteria, this portion of the gap analysis tables supplies codes and standards sections and the supplemental requirements and identifies design development requirements, if needed.

M. Johnson

2005-06-27T23:59:59.000Z

217

Machine Overview | Argonne Leadership Computing Facility  

NLE Websites -- All DOE Office Websites (Extended Search)

BG/Q Drivers Status Machine Overview Machine Partitions Torus Network Data Storage & File Systems Compiling & Linking Queueing & Running Jobs Data Transfer Debugging & Profiling Performance Tools & APIs Software & Libraries IBM References Intrepid/Challenger/Surveyor Tukey Eureka / Gadzooks Policies Documentation Feedback Please provide feedback to help guide us as we continue to build documentation for our new computing resource. [Feedback Form] Machine Overview Blue Gene /Q systems are composed of login nodes, I/O nodes, and compute nodes. Login Nodes Login and compile nodes are IBM Power 7-based systems running Red Hat Linux and are the user's interface to a Blue Gene/Q system. This is where users login, edit files, compile, and submit jobs. These are shared resources

218

RHIC Machine/Detector Planning Meetings  

NLE Websites -- All DOE Office Websites (Extended Search)

RHIC Machine/Detector Planning Meeting RHIC Machine/Detector Planning Meeting RHIC STAR PHENIX RHIC STAR PHENIX BNL Home Page C-AD Home Page C-AD ES&F Division BNL Physics Department RHIC Run History Super Conducting Magnet Division Run 14 Scheduling Physicist Home Page NPP PAC Run 13 Recommendations CAD Power Run 11-Run 13 Off-line CNI Polarization Results APEX for Run 13 RHIC Machine/Detector Meetings for Run 12 FY02-Present C-AD Energy Use Plots Cryo Power Run 11-Run 13 H-jet Target Results APEX Nov. 19-20, 2012 Workshop for Run 13 RHIC Run 13 Run Home Page (pp) FY10-Present BNL Energy Use Plot Cryo Temperatures Latest Luminosity Plots BNL Current Energy Use (BNL Intranet only and requires password) RHIC Retreat 2012

219

Gallant Precision Machining GPM | Open Energy Information  

Open Energy Info (EERE)

Gallant Precision Machining GPM Gallant Precision Machining GPM Jump to: navigation, search Name Gallant Precision Machining (GPM) Place Hsinchu, Taiwan Sector Solar Product Engaged in the design and manufacture of solar cell manufacturing equpiment. Coordinates 24.69389°, 121.148064° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":24.69389,"lon":121.148064,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

220

Micro-machined thermo-conductivity detector  

DOE Patents (OSTI)

A micro-machined thermal conductivity detector for a portable gas chromatograph. The detector is highly sensitive and has fast response time to enable detection of the small size gas samples in a portable gas chromatograph which are in the order of nanoliters. The high sensitivity and fast response time are achieved through micro-machined devices composed of a nickel wire, for example, on a silicon nitride window formed in a silicon member and about a millimeter square in size. In addition to operating as a thermal conductivity detector, the silicon nitride window with a micro-machined wire therein of the device can be utilized for a fast response heater for PCR applications.

Yu, Conrad (Antioch, CA)

2003-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "210-s machine shop" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


221

Multi-winding homopolar electric machine  

SciTech Connect

A multi-winding homopolar electric machine and method for converting between mechanical energy and electrical energy. The electric machine includes a shaft defining an axis of rotation, first and second magnets, a shielding portion, and a conductor. First and second magnets are coaxial with the shaft and include a charged pole surface and an oppositely charged pole surface, the charged pole surfaces facing one another to form a repulsive field therebetween. The shield portion extends between the magnets to confine at least a portion of the repulsive field to between the first and second magnets. The conductor extends between first and second end contacts and is toroidally coiled about the first and second magnets and the shield portion to develop a voltage across the first and second end contacts in response to rotation of the electric machine about the axis of rotation.

Van Neste, Charles W

2012-10-16T23:59:59.000Z

222

New and Underutilized Technology: Vending Machine Occupancy Sensors |  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Vending Machine Occupancy Sensors Vending Machine Occupancy Sensors New and Underutilized Technology: Vending Machine Occupancy Sensors October 7, 2013 - 9:09am Addthis The following information outlines key deployment considerations for vending machine occupancy sensors within the Federal sector. Benefits Vending machine occupancy sensors detect when no people are in the vicinity and powers down beverage vending machines. These systems do not completely turn off compressor, but reduce their run times. Application Vending machine occupancy sensors are applicable in most building categories where vending machines are present. Key Factors for Deployment Occupancy sensors or similar features should be an integral part of new vending machine purchases. Ranking Criteria Federal energy savings, cost-effectiveness, and probability of success are

223

High slot utilization systems for electric machines  

DOE Patents (OSTI)

Two new High Slot Utilization (HSU) Systems for electric machines enable the use of form wound coils that have the highest fill factor and the best use of magnetic materials. The epoxy/resin/curing treatment ensures the mechanical strength of the assembly of teeth, core, and coils. In addition, the first HSU system allows the coil layers to be moved inside the slots for the assembly purpose. The second system uses the slided-in teeth instead of the plugged-in teeth. The power density of the electric machine that uses either system can reach its highest limit.

Hsu, John S (Oak Ridge, TN)

2009-06-23T23:59:59.000Z

224

Passive machine augmented composite for multifunctional properties  

E-Print Network (OSTI)

This dissertation studies by experiment and numerical analysis an advanced composite material (Machine Augmented Composite or MAC) for enhancement of the passive damping while maintaining its stiffness. This MAC is composed of a pre-buckled wall structure placed within a viscoelastic matrix. The pre-buckled machine can contain viscous fluids for additional energy dissipation. For the experiments, the MAC was fabricated by using rigid and soft polyurethane as a machine and matrix material respectively. Various viscosity fluids (0.83 ~ 4730 cps) filled the inner-channel of the machine structure. Dynamic properties such as tan ?? and the loss modulus (E") of the composite were measured and compared with those of a homogeneous matrix sample over a frequency range of 0.1 to 100 Hz at room temperature through load-controlled cyclic testing. Measured tan ?? and loss modulus values for the composite were higher than those of the matrix alone in the 1 to 40 Hz range. However the viscous fluid effects on the overall damping properties were small. The performance of a theoretical MAC was explored through numerical analysis. The amount of inner-channel gap closure was calculated for various matrix Poisson??s ratios, for various Young??s modulus ratios between the machine and matrix (Emachine/Ematrix), and for the volume fraction of the machines. The most desirable performance of the composite was obtained when the matrix Poisson??s ratio was 0.49, and there was interaction between the Emachine/Ematrix and the volume fraction of the machines. Also the proper volume fraction range of the machine was predicted to be between 0.15 and 0.2 for the lamina shape MAC. Based upon the analysis, a sandwich structure MAC was fabricated and tested. This composite showed 11 times higher stiffness than the matrix without loosing the matrix damping property. This dissertation shows that the research met these objectives: 1) the MAC concept is effective for passive damping of vibrations, 2) that material combinations studied here had optimal combinations for best performance, and 3) that this is a promising field study for future passive and active materials development.

Kim, Jong Hyun

2005-08-01T23:59:59.000Z

225

CSP Theorems for Communicating B Machines  

E-Print Network (OSTI)

CSP Theorems for Communicating B Machines Steve Schneider and Helen Treharne Technical Report CSD #12;#12;Introduction 1 Abstract. Recent work on combining CSP and B has provided ways of describing sys- tems comprised of components described in both B (to express requirements on state) and CSP (to

Doran, Simon J.

226

Rankine cycle machines for solar cooling  

DOE Green Energy (OSTI)

A vigorous effort to develop and demonstrate practical uses of solar energy to heat and cool buildings, to process agricultural products, and to provide thermal and electrical energy for industry has been initiated. One significant part of this effort is the research, development, and demonstration of Rankine cycle machines using fluids heated by solar energy. Recent developments in three such devices are discussed briefly.

Weathers, H.M.

1978-08-01T23:59:59.000Z

227

Data management for the world's largest machine  

Science Conference Proceedings (OSTI)

The world's largest machine, the Large Hadron Collider, will have four detectors whose output is expected to answer fundamental questions about the universe. The ATLAS detector is expected to produce 3.2 PB of data per year which will be distributed ...

Sigve Haug; Farid Ould-Saada; Katarina Pajchel; Alexander L. Read

2006-06-01T23:59:59.000Z

228

Gas quantitative analysis with support vector machine  

Science Conference Proceedings (OSTI)

Gas sensor array is an important part of electronic nose. The gas analysis performance of electronic nose is affected badly by the cross sensitivity of gas sensor array. In order to solve the problem of the cross sensitivity, in this work a new method ... Keywords: electronic nose, gas mixture, quantitative analysis, support vector machine

Liang Xie; Xiaodong Wang

2009-06-01T23:59:59.000Z

229

Performance implications of virtualizing multicore cluster machines  

Science Conference Proceedings (OSTI)

High performance computers are typified by cluster machines constructed from multicore nodes and using high performance interconnects like Infiniband. Virtualizing such 'capacity computing' platforms implies the shared use of not only the nodes and node ... Keywords: Infiniband, high-performance computing, virtualization

Adit Ranadive; Mukil Kesavan; Ada Gavrilovska; Karsten Schwan

2008-03-01T23:59:59.000Z

230

HEART SMART NUTRITION Be a Lean Machine  

E-Print Network (OSTI)

Lesson 6 HEART SMART NUTRITION Be a Lean Machine This Heart Smart Nutrition series can help you Heart, Lung and Blood Institute). Physical activity increases your metabolic rate, which helps to burn more calories. Plus it helps the heart and lungs function to full capacity. Exercise also helps raise

231

Preprocessing unbalanced data using support vector machine  

Science Conference Proceedings (OSTI)

This paper deals with the application of support vector machine (SVM) to deal with the class imbalance problem. The objective of this paper is to examine the feasibility and efficiency of SVM as a preprocessor. Our study analyzes different classification ... Keywords: COIL data, Hybrid method, Preprocessor, SVM, Unbalanced data

M. A. H. Farquad; Indranil Bose

2012-04-01T23:59:59.000Z

232

Tolerating latency in replicated state machines through client speculation  

Science Conference Proceedings (OSTI)

Replicated state machines are an important and widely-studied methodology for tolerating a wide range of faults. Unfortunately, while replicas should be distributed geographically for maximum fault tolerance, current replicated state machine protocols ...

Benjamin Wester; James Cowling; Edmund B. Nightingale; Peter M. Chen; Jason Flinn; Barbara Liskov

2009-04-01T23:59:59.000Z

233

Proceedings of the 25th international conference on Machine learning  

Science Conference Proceedings (OSTI)

This volume contains the papers accepted to the 25th International Conference on Machine Learning (ICML 2008). ICML is the annual conference of the International Machine Learning Society (IMLS), and provides a venue for the presentation and discussion ...

William Cohen; Andrew McCallum; Sam Roweis

2008-07-01T23:59:59.000Z

234

Forecasting electricity demand by hybrid machine learning model  

Science Conference Proceedings (OSTI)

This paper proposes a hybrid machine learning model for electricity demand forecasting, based on Bayesian Clustering by Dynamics (BCD) and Support Vector Machine (SVM). In the proposed model, a BCD classifier is firstly applied to cluster the input data ...

Shu Fan; Chengxiong Mao; Jiadong Zhang; Luonan Chen

2006-10-01T23:59:59.000Z

235

The RWTH Aachen machine translation system for WMT 2012  

Science Conference Proceedings (OSTI)

This paper describes the statistical machine translation (SMT) systems developed at RWTH Aachen University for the translation task of the NAACL 2012 Seventh Workshop on Statistical Machine Translation (WMT 2012). We participated in the evaluation ...

Matthias Huck; Stephan Peitz; Markus Freitag; Malte Nuhn; Hermann Ney

2012-06-01T23:59:59.000Z

236

Virtual cutter path display for dental milling machine  

E-Print Network (OSTI)

This paper presents the prototype of a mixed reality system using the computer controlled dental milling machine, which is called MRD Mill. First, overview of the core dental milling machine developed in this study is ...

Ito, Teruaki

237

Machine Learning Forensics for Law Enforcement, Security, and Intelligence  

Science Conference Proceedings (OSTI)

Increasingly, crimes and fraud are digital in nature, occurring at breakneck speed and encompassing large volumes of data. To combat this unlawful activity, knowledge about the use of machine learning technology and software is critical. Machine Learning ...

Jesus Mena

2011-06-01T23:59:59.000Z

238

Seattle City Light - Vending Machine Rebate Program | Department...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

of VendingMiser Energy Efficient Vending Machines. VendingMiser reduces the energy consumption of cold drink vending machines by using an occupancy sensor to power down the...

239

A Bahadur Representation of the Linear Support Vector Machine  

Science Conference Proceedings (OSTI)

The support vector machine has been successful in a variety of applications. Also on the theoretical front, statistical properties of the support vector machine have been studied quite extensively with a particular attention to its Bayes risk consistency ...

Ja-Yong Koo; Yoonkyung Lee; Yuwon Kim; Changyi Park

2008-06-01T23:59:59.000Z

240

Magnesium: Digital Resource Center - ARTICLE: Safe Machining of ...  

Science Conference Proceedings (OSTI)

Sep 7, 2007... Other ==== Miscellaneous Digital Resources in Magnesium. Spacer ... Topic Title: ARTICLE: Safe Machining of Magnesium Parts by Cutting ...

Note: This page contains sample records for the topic "210-s machine shop" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


241

NIST Open Machine Translation (OpenMT) Evaluation  

Science Conference Proceedings (OSTI)

DARPA TIDES Machine Translation 2004 Evaluation (MT04). Current and Recent DARPA TIDES MT Activities. MT04 takes ...

242

A Reordering Model for Phrase-Based Machine Translation  

Science Conference Proceedings (OSTI)

This paper presents a new method for reordering in phrase based statistical machine translation (PBSMT). Our method is based on previous chunk-level reordering methods for PBSMT. Our method is a global reordering. First, we parse the source language ... Keywords: Machine Translation, Natural Language Processing, Phrase-based Statistical Machine Translation

Vinh Nguyen; Thai Phuong Nguyen; Akira Shimazu; Minh Nguyen

2008-08-01T23:59:59.000Z

243

Argument based machine learning in a medical domain  

Science Conference Proceedings (OSTI)

Argument Based Machine Learning (ABML) is a new approach to machine learning in which the learning examples can be accompanied by arguments. The arguments for specific examples are a special form of expert's knowledge which the expert uses to substantiate ... Keywords: Argument Based Machine Learning, Bacterial Infections, Geriatric Population, Rule Learning

Jure Žabkar; Martin Možina; Jerneja Vide?nik; Ivan Bratko

2006-05-01T23:59:59.000Z

244

Interacting meaningfully with machine learning systems: Three experiments  

Science Conference Proceedings (OSTI)

Although machine learning is becoming commonly used in today's software, there has been little research into how end users might interact with machine learning systems, beyond communicating simple ''right/wrong'' judgments. If the users themselves could ... Keywords: Explanations, Intelligent user interfaces, Machine learning, Rich feedback

Simone Stumpf; Vidya Rajaram; Lida Li; Weng-Keen Wong; Margaret Burnett; Thomas Dietterich; Erin Sullivan; Jonathan Herlocker

2009-08-01T23:59:59.000Z

245

Improving energy efficiency of buffer cache in virtual machines  

Science Conference Proceedings (OSTI)

Main memory contributes a large fraction of energy consumption in powerful servers running virtualization software to support concurrent virtual machines (VMs). Furthermore, data-intensive applications executing inside virtual machines increase the demand ... Keywords: Buffer Cache,Virtual Machine,Energy Management

Lei Ye; Chris Gniady

2012-06-01T23:59:59.000Z

246

Long Term Climate Simulations Using an Adaptable Virtual Machine.  

E-Print Network (OSTI)

the DOE NERSC, a re­ mote machine could be added to the virtual machine until the NERSC account test bed. Another is to include the NERSC machines at LBL, the Cray C90 and the Cray T3E connections, particularly into NERSC, would be important for the success of this project. The latency

247

Constructive hidden nodes selection of extreme learning machine for regression  

Science Conference Proceedings (OSTI)

In this paper, we attempt to address the architectural design of ELM regressor by applying a constructive method on the basis of ELM algorithm. After the nonlinearities of ELM network are fixed by randomly generating the parameters, the network will ... Keywords: Constructive method, Error-minimized extreme learning machine, Extreme learning machine, Incremental extreme learning machine

Yuan Lan; Yeng Chai Soh; Guang-Bin Huang

2010-10-01T23:59:59.000Z

248

A real-time virtual machine implementation for small microcontrollers  

Science Conference Proceedings (OSTI)

A way to host a full general purpose virtual machine (VM) interpreter on a very small microcontroller platform is described. This machine provides a comprehensive set of general and enhanced functionality efficiently by abstracting the VM instruction ... Keywords: Microcontrollers, Real-time systems, Virtual machine

W. Roger Davis; Phillip A. Laplante; Bo I. Sandén

2012-09-01T23:59:59.000Z

249

Scheduling a capacitated batch-processing machine to minimize makespan  

Science Conference Proceedings (OSTI)

This paper aims at improving the utilization of a single batch-processing machine. The batch-processing machine can process a batch of jobs, as long as the number of jobs and the total size of all the jobs in a batch do not violate the machine's capacity. ... Keywords: Batch processing, Mathematical modeling, Scheduling, Simulated annealing

Purushothaman Damodaran; Krishnaswami Srihari; Sarah S. Lam

2007-04-01T23:59:59.000Z

250

Virtual Data System on distributed virtual machines in computational grids  

Science Conference Proceedings (OSTI)

This paper presents the work of building a Grid workflow system on distributed virtual machines. A Grid Virtualisation Engine (GVE) is implemented to manage virtual machines as computing resources for Grid applications. The Virtual Data System ... Keywords: compact muon solenoid, distributed virtual machines, grid computing, grid workflow, high energy physics applications, virtual data systems

Lizhe Wang; Gregor Von Laszewski; Jie Tao; Marcel Kunze

2010-09-01T23:59:59.000Z

251

Super-tasks, accelerating Turing machines and uncomputability  

Science Conference Proceedings (OSTI)

Accelerating Turing machines are devices with the same computational structure as Turing machines (TM), but able to perform super-tasks. We ask whether performing super-tasks alone produces more computational power; for example, whether accelerating ... Keywords: Thomson's paradox, accelerating Turing machines, halting problem, super-task

Oron Shagrir

2004-06-01T23:59:59.000Z

252

Estimation of synchronous machine parameters by standstill tests  

Science Conference Proceedings (OSTI)

In this paper we present the results of a time-domain identification procedure to estimate the linear parameters of a salient-pole synchronous machine at standstill. A new approach is proposed for the estimation of synchronous machine coupled to DC-chopper ... Keywords: Parameter estimation, Standstill tests, Synchronous machine

M. Hasni; O. Touhami; R. Ibtiouen; M. Fadel; S. Caux

2010-10-01T23:59:59.000Z

253

Mechanical design of a desktop milling machine for fabrication in an introductory machining class by Johannes Schneider.  

E-Print Network (OSTI)

The purpose of this research is the mechanical design of a miniature desktop milling machine for use as an alternative class project in MIT's introductory machining course 2.670. This research is important, because a ...

Schneider, Johannes (Johannes A.)

2010-01-01T23:59:59.000Z

254

Hybrid-secondary uncluttered induction machine  

DOE Patents (OSTI)

An uncluttered secondary induction machine (100) includes an uncluttered rotating transformer (66) which is mounted on the same shaft as the rotor (73) of the induction machine. Current in the rotor (73) is electrically connected to current in the rotor winding (67) of the transformer, which is not electrically connected to, but is magnetically coupled to, a stator secondary winding (40). The stator secondary winding (40) is alternately connected to an effective resistance (41), an AC source inverter (42) or a magnetic switch (43) to provide a cost effective slip-energy-controlled, adjustable speed, induction motor that operates over a wide speed range from below synchronous speed to above synchronous speed based on the AC line frequency fed to the stator.

Hsu, John S. (Oak Ridge, TN)

2001-01-01T23:59:59.000Z

255

R&D ERL: Machine Protection System  

SciTech Connect

The Machine Protection System (MPS) is a device-safety system that is designed to prevent damage to hardware by generating interlocks, based upon the state of input signals generated by selected sub-system. It exists to protect key machinery such as the 50 kW and 1 MW RF Systems. When a fault state occurs, the MPS is capable of responding with an interlock signal within several microseconds. The Machine Protection System inputs are designed to be fail-safe. In addition, all fault conditions are latched and time-stamped. The ERL MPS is based on a National Instruments hardware platform, and is programmed by utilizing National Instruments development environment for a visual programming language.

Altinbas, Z.

2010-01-01T23:59:59.000Z

256

Walcot Electric Machines | Open Energy Information  

Open Energy Info (EERE)

Walcot Electric Machines Walcot Electric Machines Jump to: navigation, search Name Walcot Electric Machines Place Bath, United Kingdom Zip BA2 7AY Sector Efficiency Product A spin-out from Bath University which that will develop and licence process relating to high efficiency electric motors for fixed speed applications, and will offer endusers substantial reductions in the cost of operation Coordinates 45.467055°, -98.329279° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":45.467055,"lon":-98.329279,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

257

Dovetail spoke internal permanent magnet machine  

Science Conference Proceedings (OSTI)

An internal permanent magnet (IPM) machine is provided. The IPM machine includes a stator assembly and a stator core. The stator core also includes multiple stator teeth. The stator assembly is further configured with stator windings to generate a stator magnetic field when excited with alternating currents and extends along a longitudinal axis with an inner surface defining a cavity. The IPM machine also includes a rotor assembly and a rotor core. The rotor core is disposed inside the cavity and configured to rotate about the longitudinal axis. The rotor assembly further includes a shaft. The shaft further includes multiple protrusions alternately arranged relative to multiple bottom structures provided on the shaft. The rotor assembly also includes multiple stacks of laminations disposed on the protrusions and dovetailed circumferentially around the shaft. The rotor assembly further includes multiple pair of permanent magnets for generating a magnetic field, which magnetic field interacts with the stator magnetic field to produce a torque. The multiple pair of permanent magnets are disposed between the stacks. The rotor assembly also includes multiple middle wedges mounted between each pair of the multiple permanent magnets.

Alexander, James Pellegrino (Ballston Lake, NY); EL-Refaie, Ayman Mohamed Fawzi (Niskayuna, NY); Lokhandwalla, Murtuza (Clifton Park, NY); Shah, Manoj Ramprasad (Latham, NY); VanDam, Jeremy Daniel (West Coxsackie, NY)

2011-08-23T23:59:59.000Z

258

Positional reference system for ultraprecision machining  

DOE Patents (OSTI)

A stable positional reference system for use in improving the cutting tool-to-part contour position in numerical controlled-multiaxis metal turning machines is provided. The reference system employs a plurality of interferometers referenced to orthogonally disposed metering bars which are substantially isolated from machine strain induced position errors for monitoring the part and tool positions relative to the metering bars. A microprocessor-based control system is employed in conjunction with the plurality of position interferometers and part contour description data inputs to calculate error components for each axis of movement and output them to corresponding axis drives with appropriate scaling and error compensation. Real-time position control, operating in combination with the reference system, makes possible the positioning of the cutting points of a tool along a part locus with a substantially greater degree of accuracy than has been attained previously in the art by referencing and then monitoring only the tool motion relative to a reference position located on the machine base.

Arnold, Jones B. (Knoxville, TN); Burleson, Robert R. (Clinton, TN); Pardue, Robert M. (Knoxville, TN)

1982-01-01T23:59:59.000Z

259

Positional reference system for ultraprecision machining  

DOE Patents (OSTI)

A stable positional reference system for use in improving the cutting tool-to-part contour position in numerical controlled-multiaxis metal turning machines is provided. The reference system employs a plurality of interferometers referenced to orthogonally disposed metering bars which are substantially isolated from machine strain induced position errors for monitoring the part and tool positions relative to the metering bars. A microprocessor-based control system is employed in conjunction with the plurality of positions interferometers and part contour description data input to calculate error components for each axis of movement and output them to corresponding axis driven with appropriate scaling and error compensation. Real-time position control, operating in combination with the reference system, makes possible the positioning of the cutting points of a tool along a part locus with a substantially greater degree of accuracy than has been attained previously in the art by referencing and then monitoring only the tool motion relative to a reference position located on the machine base.

Arnold, J.B.; Burleson, R.R.; Pardue, R.M.

1980-09-12T23:59:59.000Z

260

El Ma Electronic Machining srl | Open Energy Information  

Open Energy Info (EERE)

Ma Electronic Machining srl Ma Electronic Machining srl Jump to: navigation, search Name El.Ma. Electronic Machining srl Place Riva del Garda (TN), Italy Zip 38066 Sector Hydro, Hydrogen, Solar, Wind energy Product String representation "Italy-based, in ... solar sectors." is too long. References El.Ma. Electronic Machining srl[1] LinkedIn Connections CrunchBase Profile No CrunchBase profile. Create one now! This article is a stub. You can help OpenEI by expanding it. El.Ma. Electronic Machining srl is a company located in Riva del Garda (TN), Italy . References ↑ "El.Ma. Electronic Machining srl" Retrieved from "http://en.openei.org/w/index.php?title=El_Ma_Electronic_Machining_srl&oldid=344591" Categories: Clean Energy Organizations Companies Organizations

Note: This page contains sample records for the topic "210-s machine shop" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


261

Photo of the Week: The Z Machine | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

The Z Machine The Z Machine Photo of the Week: The Z Machine September 21, 2012 - 11:08am Addthis The Z machine, the largest X-ray generator in the world, is located in Albuquerque, New Mexico. As part of the Pulsed Power Program, which started at Sandia National Laboratories in the 1960s, the Z machine concentrates electrical energy and turns it into short pulses of enormous power, which can then be used to generate X-rays and gamma rays. Click on the image for a full size version. | Photo credit: Randy Montoya/Sandia National Laboratories. The Z machine, the largest X-ray generator in the world, is located in Albuquerque, New Mexico. As part of the Pulsed Power Program, which started at Sandia National Laboratories in the 1960s, the Z machine concentrates electrical energy and turns it into short pulses of enormous power, which

262

Parameter optimization of modern machining processes using teaching-learning-based optimization algorithm  

Science Conference Proceedings (OSTI)

Modern machining processes are now-a-days widely used by manufacturing industries in order to produce high quality precise and very complex products. These modern machining processes involve large number of input parameters which may affect the cost ... Keywords: Abrasive jet machining, Modern machining processes, Parameter optimization, TLBO algorithm, Ultrasonic machining, Wire electrical discharge machining

R. Venkata Rao; V. D. Kalyankar

2013-01-01T23:59:59.000Z

263

Laboratory Directed Research and Development Final Report Intelligent Tools for On-Machine Acceptance of Precision Machined Components  

E-Print Network (OSTI)

On-Machine Acceptance (OMA) is an agile manufacturing concept being developed for machine tools at SNL. The concept behind OMA is the integration of product design, fabrication, and qualification processes by using the machining center as a fabrication and inspection tool. This report documents the final results of a Laboratory Directed Research and Development effort to qualify OMA. Intelligent Tools for On-Machine Acceptance of Precision Machined Components 2 Acknowledgments Thanks to Don Sheaffer, Department 8120, Mark Powell, Department 9611, and Marcey Abate, Department 12323, for their contributions to this final report. Thanks to Tony Bryce, and Dennis Clingan, Department 1484, Phil Skogmo, Department 2645, and Charles Steinhaus, Department 8240, for their assistance in writing this report. Intelligent Tools for On-Machine Acceptance of Precision Machined Components 3 Contents 1.0 Introduction .................................................................................

Naomi Christensen Precision; Naomi G. Christensen; Lane D. Harwell; Andrew Hazelton

1996-01-01T23:59:59.000Z

264

Page not found | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

41 - 8550 of 29,416 results. 41 - 8550 of 29,416 results. Download CX-006386: Categorical Exclusion Determination Grouting of Storm Sewer Grates and Man Holes at 770U CX(s) Applied: B1.28 Date: 06/13/2011 Location(s): Aiken, South Carolina Office(s): Environmental Management, Savannah River Operations Office http://energy.gov/nepa/downloads/cx-006386-categorical-exclusion-determination Download CX-006387: Categorical Exclusion Determination Kennel Lights and Sidewalk Date: 06/08/2011 Location(s): Aiken, South Carolina Office(s): Environmental Management, Savannah River Operations Office http://energy.gov/nepa/downloads/cx-006387-categorical-exclusion-determination Download CX-006388: Categorical Exclusion Determination Installation of Water Jet Cutter into 210-S Machine Shop CX(s) Applied: B1.3

265

Categorical Exclusion (CX) Determinations By Date | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

9, 2011 9, 2011 CX-007082: Categorical Exclusion Determination Provide Telecommunications Cable to Buildings 6750 and 6753 CX(s) Applied: B1.7 Date: 06/09/2011 Location(s): Albuquerque, New Mexico Office(s): NNSA-Headquarters, Sandia Site Office June 9, 2011 CX-007081: Categorical Exclusion Determination Installation of 7 New Storm Water Monitoring Stations CX(s) Applied: B3.1 Date: 06/09/2011 Location(s): Albuquerque, New Mexico Office(s): NNSA-Headquarters, Sandia Site Office June 8, 2011 CX-006388: Categorical Exclusion Determination Installation of Water Jet Cutter into 210-S Machine Shop CX(s) Applied: B1.3 Date: 06/08/2011 Location(s): Aiken, South Carolina Office(s): Environmental Management, Savannah River Operations Office June 8, 2011 CX-006389: Categorical Exclusion Determination

266

Machine augmented composite materials for damping purposes  

E-Print Network (OSTI)

In this study the energy dissipation performance of machine augmented composite (MAC) materials is investigated. MAC materials are formed by inserting simple machines into a matrix material. In this work the machines take the form of fluid filled tubes, and the tube cross-sectional geometry induces fluid flow when it is deformed in its plane. This flow dissipates mechanical energy, and thus provides the composite material with attractive damping properties. The objective of this study is to gain insight into the geometry, the material property combinations, and the boundary conditions that are effective in producing high damping MAC materials. Particular attention is given to tube geometry and to dimensionless parameters that govern the energy dissipation efficiency of a MAC lamina. An important dimensionless parameter is the ratio of solid elastic moduli to the product of the driving frequency and the fluid dynamic viscosity. This is a measure of the ratio of elastic forces in the solid material to the viscous forces in the fluid material that makes up a MAC lamina. Governing equations and simulation methods are discussed. Simplified equations are derived to predict the pressure generated when a tube/matrix cell is squeezed with zero pressure end conditions. Transient, three dimensional finite element models are also used to predict the performance of the damping MAC materials with zero pressure at the ends of the tubes. For the geometry and material properties considered, the highest energy dissipation efficiency predicted by these models is approximately 0.8 out of a maximum of 1.0.

McCutcheon, David Matthew

2004-12-01T23:59:59.000Z

267

Ccg supertags in factored statistical machine translation  

E-Print Network (OSTI)

Combinatorial Categorial Grammar (CCG) supertags present phrase-based machine translation with an opportunity to access rich syntactic information at a word level. The challenge is incorporating this information into the translation process. Factored translation models allow the inclusion of supertags as a factor in the source or target language. We show that this results in an improvement in the quality of translation and that the value of syntactic supertags in flat structured phrase-based models is largely due to better local reorderings. 1

Alexandra Birch; Miles Osborne

2007-01-01T23:59:59.000Z

268

International Journal of Machine Tools & Manufacture 47 (2007) 22732281 Near dry electrical discharge machining  

E-Print Network (OSTI)

discharge machining C.C. Kao, Jia Tao, Albert J. ShihÃ? Mechanical Engineering, University of Michigan, Ann. The dielectric strength, defined as the maximum electric field strength that the dielectric fluid can withstand and kerosene-based oil are two commonly used dielectric fluids in conventional wet EDM. Dry EDM uses gas

Shih, Albert J.

269

Agile Machining and Inspection Non-Nuclear Report (NNR) Project  

SciTech Connect

This report is a high level summary of the eight major projects funded by the Agile Machining and Inspection Non-Nuclear Readiness (NNR) project (FY06.0422.3.04.R1). The largest project of the group is the Rapid Response project in which the six major sub categories are summarized. This project focused on the operations of the machining departments that will comprise Special Applications Machining (SAM) in the Kansas City Responsive Infrastructure Manufacturing & Sourcing (KCRIMS) project. This project was aimed at upgrading older machine tools, developing new inspection tools, eliminating Classified Removable Electronic Media (CREM) in the handling of classified Numerical Control (NC) programs by installing the CRONOS network, and developing methods to automatically load Coordinated-Measuring Machine (CMM) inspection data into bomb books and product score cards. Finally, the project personnel leaned perations of some of the machine tool cells, and now have the model to continue this activity.

Lazarus, Lloyd

2009-02-19T23:59:59.000Z

270

Energy Cost Calculator for Commercial Ice Machines | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Ice Machines Ice Machines Energy Cost Calculator for Commercial Ice Machines October 8, 2013 - 2:25pm Addthis Vary capacity size, energy cost, hours of operation, and /or efficiency level. INPUT SECTION Input the following data (if any parameter is missing, calculator will set to default value). Defaults Type of Ice Cube Machine Ice Making Head Self-Contained Remote Condensing Unit Ice Making Head Type of Condenser Air Cooled Water Cooled Air Cooled Ice Harvest Rate (lbs. ice per 24 hrs.) lbs. per 24 hrs. 500 lbs. per 24 hrs. Energy Consumption (per 100 lbs. of ice) kWh 5.5 kWh Quantity of ice machines to be purchased 1 Energy Cost $/kWh 0.06 $/kWh Annual Hours of Operation hrs. 3000 hrs. Calculate Reset OUTPUT SECTION Performance per Ice Cube Machine Your

271

Edge diagnostics for tandem mirror machines  

SciTech Connect

The edge plasma in a tandem mirror machine shields the plasma core from cold neutral gas and impurities. A variety of diagnostics are used to measure the fueling, shielding, and confinement of the edge plasma in both the end plug and central cell regions. Fast ion gauges and residual gas analyzers measure the gas pressure and composition outside of the plasma. An array of Langmuir probes is used to measure the electron density and temperature. Extreme ultraviolet (euv) and visible spectroscopy are used to measure both the impurity and deuterium densities and to estimate the shielding factor for the core plasma. The linear geometry of a tandem mirror also allows direct measurements of the edge plasma by sampling the ions and electrons lost but the ends of the machine. Representative data obtained by these diagnostics during operation of the Tandem Mirror Experiment (TMX) and Tandem Mirror Experiment-Upgrade (TMX-U) experiments are presented. Diagnostics that are currently being developed to diagnose the edge plasma are also discussed.

Allen, S.L.

1984-09-14T23:59:59.000Z

272

Evaluation of machining dispersions for turning process  

E-Print Network (OSTI)

In this article we propose to extend the model of simulation of dispersions in turning based on the geometrical specifications. Our study is articulated around two trends of development: the first trend relates to the geometrical model. The geometrical model suggested must allow a follow-up of the geometry of the part during the simulation of machining. It is thus a question of carrying out a systematic treatment of the whole dimensioning and tolerancing process while being based on the principles of the \\DeltaL method. We also planned to integrate this type of specification in the model of simulation of machining suggested. It is more generally a question of extending the traditional model for better taking into account the multi axis specification of coaxiality and perpendicularity on the turned workpieces. The second trend of our study relates to the widening of the field of application of the model. We propose to extend the field of application of the model by taking into account the modifications of several parameters of the manufacturing process plans, likely to involve variations of dispersions.

Arnaud Lefebvre; Valery Wolff

2008-03-03T23:59:59.000Z

273

Automatic tool path generation for finish machining  

SciTech Connect

A system for automatic tool path generation was developed at Sandia National Laboratories for finish machining operations. The system consists of a commercially available 5-axis milling machine controlled by Sandia developed software. This system was used to remove overspray on cast turbine blades. A laser-based, structured-light sensor, mounted on a tool holder, is used to collect 3D data points around the surface of the turbine blade. Using the digitized model of the blade, a tool path is generated which will drive a 0.375 inch diameter CBN grinding pin around the tip of the blade. A fuzzified digital filter was developed to properly eliminate false sensor readings caused by burrs, holes and overspray. The digital filter was found to successfully generate the correct tool path for a blade with intentionally scanned holes and defects. The fuzzified filter improved the computation efficiency by a factor of 25. For application to general parts, an adaptive scanning algorithm was developed and presented with simulation results. A right pyramid and an ellipsoid were scanned successfully with the adaptive algorithm.

Kwok, Kwan S.; Loucks, C.S.; Driessen, B.J.

1997-03-01T23:59:59.000Z

274

Multi-winding Homopolar Electric Machine Offers Variable Voltage ...  

Wind Energy Industrial Technologies Multi-winding Homopolar Electric Machine Offers Variable Voltage at Low Rotational Speed Oak Ridge National Laboratory. Contact ...

275

Combined Electric Machine and Current Source Inverter Drive System ...  

Wind power generators ; Industrial power generators; More Information John S. Hsu. Combined Electric Machine and Current Source Invertor Drive System, U.S ...

276

Electrical machines and assemblies including a yokeless stator ...  

Wind Energy; Partners (27) Visual Patent Search; Success Stories; News; Events; Electrical machines and assemblies including a yokeless stator with modular lamination ...

277

DOE - Office of Legacy Management -- Cincinnati Milling and Machining...  

NLE Websites -- All DOE Office Websites (Extended Search)

& Machining Co. (OH.25 ) Eliminated from consideration under FUSRAP - Referred to NRC Designated Name: Not Designated Alternate Name: None Location: Cincinnati , Ohio...

278

Livermore installs big data machine | National Nuclear Security...  

National Nuclear Security Administration (NNSA)

installs big data machine | National Nuclear Security Administration Our Mission Managing the Stockpile Preventing Proliferation Powering the Nuclear Navy Emergency Response...

279

Parallel machine scheduling with nested job assignment restrictions  

Science Conference Proceedings (OSTI)

We derive a polynomial time approximation scheme for a special case of makespan minimization on unrelated machines. Keywords: Approximation algorithms, Restricted assignment, Scheduling

Gabriella Muratore; Ulrich M. Schwarz; Gerhard J. Woeginger

2010-01-01T23:59:59.000Z

280

KCP relocates 18-ton machine | National Nuclear Security Administratio...  

NLE Websites -- All DOE Office Websites (Extended Search)

relocates 18-ton machine | National Nuclear Security Administration Our Mission Managing the Stockpile Preventing Proliferation Powering the Nuclear Navy Emergency Response...

Note: This page contains sample records for the topic "210-s machine shop" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


281

A Column Generation Approach for Support Vector Machines  

E-Print Network (OSTI)

Mar 23, 2006 ... For instance, taking the Wisconsin Breast Cancer Database from the UCI Machine ..... European Journal of Operational Research. In press.

282

John Hsu, Oak Ridge National Laboratory, Flux Coupling Machines...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

John Hsu, Oak Ridge National Laboratory, Flux Coupling Machines and Switched Reluctance Motors to Replace Permanent Magnets in Electric Vehicles John Hsu, Oak Ridge National...

283

Hybrid-secondary uncluttered permanent magnet machine and ...  

An electric machine (40) has a stator (43), a permanent magnet rotor (38) with permanent magnets (39) and a magnetic coupling uncluttered rotor (46) for inducing a ...

284

Vending Machine Energy Consumption and VendingMiser Evaluation  

E-Print Network (OSTI)

As an effort to decrease the amount of non-critical energy used on the Texas A&M campus, and to assist Dixie Narco in evaluating the efficiency of their vending machines, the Texas A&M Energy Systems Laboratory investigated the power consumption of soda vending machines on the Texas A&M campus. Several vending machines were evaluated to determine the power consumption for the individual components, and the whole machine. Recommendations were made from the results. The VendingMiser device was also tested to evaluate the potential energy savings of this device.

Ritter, J.; Hugghins, J.

2000-01-01T23:59:59.000Z

285

Sandia gives Japanese elected official a tour of Z machine |...  

National Nuclear Security Administration (NNSA)

gives Japanese elected official a tour of Z machine | National Nuclear Security Administration Our Mission Managing the Stockpile Preventing Proliferation Powering the Nuclear Navy...

286

Hybrid MPI/OpenMP parallel support vector machine training  

E-Print Network (OSTI)

Jan 12, 2009 ... A parallel implementation of Support Vector Machine training has been developed, using a combination of MPI and OpenMP. Using an interior ...

287

Exploiting separability in large-scale Support Vector Machine training  

E-Print Network (OSTI)

Aug 8, 2007 ... Abstract: Linear support vector machine training can be represented as a large quadratic program. We present an efficient and numerically ...

288

Interpolator for numerically controlled machine tools  

DOE Patents (OSTI)

A digital differential analyzer circuit is provided that depending on the embodiment chosen can carry out linear, parabolic, circular or cubic interpolation. In the embodiment for parabolic interpolations, the circuit provides pulse trains for the X and Y slide motors of a two-axis machine to effect tool motion along a parabolic path. The pulse trains are generated by the circuit in such a way that parabolic tool motion is obtained from information contained in only one block of binary input data. A part contour may be approximated by one or more parabolic arcs. Acceleration and initial velocity values from a data block are set in fixed bit size registers for each axis separately but simultaneously and the values are integrated to obtain the movement along the respective axis as a function of time. Integration is performed by continual addition at a specified rate of an integrand value stored in one register to the remainder temporarily stored in another identical size register. Overflows from the addition process are indicative of the integral. The overflow output pulses from the second integration may be applied to motors which position the respective machine slides according to a parabolic motion in time to produce a parabolic machine tool motion in space. An additional register for each axis is provided in the circuit to allow "floating" of the radix points of the integrand registers and the velocity increment to improve position accuracy and to reduce errors encountered when the acceleration integrand magnitudes are small when compared to the velocity integrands. A divider circuit is provided in the output of the circuit to smooth the output pulse spacing and prevent motor stall, because the overflow pulses produced in the binary addition process are spaced unevenly in time. The divider has the effect of passing only every nth motor drive pulse, with n being specifiable. The circuit inputs (integrands, rates, etc.) are scaled to give exactly n times the desired number of pulses out, in order to compensate for the divider.

Bowers, Gary L. (Clinton, TN); Davenport, Clyde M. (Oak Ridge, TN); Stephens, Albert E. (Knoxville, TN)

1976-01-01T23:59:59.000Z

289

Optimisation of machining processes design for Stellite 6, a wear resistant and difficult-to-machine material.  

E-Print Network (OSTI)

??"The research work in this thesis involves a series of physical experiments and theoretical investigations for machining of Stellite 6 using PCBN (Polycrystalline Cubic Boron… (more)

Hasan, Md Shahanur.

2011-01-01T23:59:59.000Z

290

Technology: Machine and its interpretation in architecture  

E-Print Network (OSTI)

The objective of this study is to develop a comprehensive theory for the relationship between architecture and technology and to examine the interpretation of technology when it is applied to architecture. In architecture, 'art and craft' and 'doing and saying (presentation)' are closely interwoven. It is sensitive to the external environment in nature, and its boundary has been actively changed. The nineteenth century brought the sudden alteration of culture with the collaboration between science and its applied means or knowledge - "technology". Subsequently, in the twentieth century, the new culture has transformed our normal life style and we can perceive the development of civilization sensuously. The machine as a product of industrial civilization and the symbol of technology has generated new meanings and tradition in tune with this historical trend. Therefore, this study will center on the concept 'technology', which is one of the conspicuous factors in the formation of modern architecture, and it will investigate the relationship between technology and architecture.

Kim, Ju Hong

2002-01-01T23:59:59.000Z

291

Applying Alpha-Channeling to Mirror Machines  

SciTech Connect

The ?-channeling effect entails the use of radio-frequency waves to expel and cool high-energetic ?- particles born in a fusion reactor; the device reactivity can then be increased even further by redirecting the extracted energy to fuel ions. Originally proposed for tokamaks, this technique has also been shown to benefi t open-ended fusion devices. Here, the fundamental theory and practical aspects of ?- channeling in mirror machines are reviewed, including the influence of magnetic field inhomogeneity and the effect of a finite wave region on the ?-channeling mechanism. For practical implementation of the ? -channeling effect in mirror geometry, suitable contained weakly-damped modes are identifi ed. In addition, the parameter space of candidate waves for implementing the ? -channeling effect can be signi cantly extended through the introduction of a suitable minority ion species that has the catalytic effect of moderating the transfer of power from the ?-channeling wave to the fuel ions.

A.I. Zhmoginov and N.J. Fisch

2012-03-16T23:59:59.000Z

292

Design studies of mirror machine reactors  

SciTech Connect

An overview is presented of a mirror fusion reactor design study. The general methodology used in the study is discussed, the reactor is described, and some design alternatives to the present approach are enumerated. The system chosen for this design study is a mirror machine with direct conversion using D- T fuel. The nominal power output is 200 MW. The coil geometry is the Yin Yang, minimum B with a vacuum mirror ratio of 3. The coil is of particular utility because of its simple conductor shapes and because the two separate conductors, by proper B-field biasing, allow the charged particles to escape preferentially through one mirror only and through a relatively small window'' of that mirror. This is necessary for direct converter economy. (auth)

Werner, R.W.; Carlson, G.A.; Hovingh, J.; Lee, J.D.; Peterson, M.A.

1973-12-01T23:59:59.000Z

293

Energy Efficient Allocation of Virtual Machines in Cloud Data Centers  

Science Conference Proceedings (OSTI)

Rapid growth of the demand for computational power has led to the creation of large-scale data centers. They consume enormous amounts of electrical power resulting in high operational costs and carbon dioxide emissions. Moreover, modern Cloud computing ... Keywords: Energy efficiency, Cloud computing, Energy consumption, Green IT, Resource management, Virtualization, Allocation of virtual machines, Live migration of virtual machines

Anton Beloglazov; Rajkumar Buyya

2010-05-01T23:59:59.000Z

294

Brain-controlled finite state machine for wheelchair navigation  

Science Conference Proceedings (OSTI)

This proposal is about a brain-controlled electrically powered wheelchair. The system comprises a brain-computer interface based on steady-state visual evoked potentials and a processing unit relying on a finite state machine (FSM). Results of first ... Keywords: brain-computer interface (bci), finite state machine (fsm), human-computer interaction, stea dy-state visual evoked potentials (ssvep)

Amir Teymourian; Thorsten Lueth; Axel Graeser; Torsten Felzer; Rainer Nordmann

2008-10-01T23:59:59.000Z

295

Synthesizing hierarchical state machines from expressive scenario descriptions  

Science Conference Proceedings (OSTI)

There are many examples in the literature of algorithms for synthesizing state machines from scenario-based models. The motivation for these is to automate the transition from scenario-based requirements to early behavioral design models. To date, however, ... Keywords: State machine synthesis, interaction overview diagrams, scenario-based requirements, software modeling

Jon Whittle; Praveen K. Jayaraman

2010-01-01T23:59:59.000Z

296

Monthly streamflow forecasting based on improved support vector machine model  

Science Conference Proceedings (OSTI)

To improve the performance of the support vector machine (SVM) model in predicting monthly streamflow, an improved SVM model with adaptive insensitive factor is proposed in this paper. Meanwhile, considering the influence of noise and the disadvantages ... Keywords: Adaptive insensitive factor, Artificial neural network, Chaos and phase-space reconstruction theory, Streamflow forecast, Support vector machine, Wavelet

Jun Guo; Jianzhong Zhou; Hui Qin; Qiang Zou; Qingqing Li

2011-09-01T23:59:59.000Z

297

Terminal models for switching overvoltage studies in electrical machines  

Science Conference Proceedings (OSTI)

In this paper, terminal models for high voltage machine windings are developed. The models are useful for simulating transient overvoltages due to switching operations on industrial installations. The models are based on network synthesis of the winding ... Keywords: electrical parameters, machine winding, network synthesis, switching transients, terminal impedance

J. L. Guardado; V. Venegas; E. Melgoza

2006-03-01T23:59:59.000Z

298

Fatigue crack growth estimation by relevance vector machine  

Science Conference Proceedings (OSTI)

The investigation of damage propagation mechanisms on a selected safety-critical component or structure requires the quantification of its remaining useful life (RUL) to verify until when it can continue performing the required function. In this work, ... Keywords: Bayesian techniques, Fatigue crack growth, Prognostics, Relevance vector machine, Residual useful life, Support vector machine

Enrico Zio; Francesco Di Maio

2012-09-01T23:59:59.000Z

299

Advanced support vector machines for 802.11 indoor location  

Science Conference Proceedings (OSTI)

Due to the proliferation of ubiquitous computing services, locating a device in indoor scenarios has received special attention during recent years. A variety of algorithms are based on Wi-Fi measurements of the received signal strength and estimate ... Keywords: Autocorrelation kernel, Complex support vector machines, Fingerprinting, IEEE 802.11, Indoor location, Support vector machines

Carlos Figuera; José Luis Rojo-Álvarez; Mark Wilby; Inmaculada Mora-Jiménez; Antonio J. Caamaño

2012-09-01T23:59:59.000Z

300

Grading of construction aggregate through machine vision: Results and prospects  

Science Conference Proceedings (OSTI)

Traditionally, crushed aggregate to be used in construction is graded using sieves. We describe an innovative machine vision approach to such grading. Our operational scenario is one where a camera takes images from directly overhead of a layer of aggregate ... Keywords: Construction industry, Image database, Machine vision, Supervised and unsupervised classification, Wavelet transform

Fionn Murtagh; Xiaoyu Qiao; Paul Walsh; P. A. M. Basheer; Danny Crookes; Adrian Long

2005-12-01T23:59:59.000Z

Note: This page contains sample records for the topic "210-s machine shop" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


301

Bounded sequence testing from deterministic finite state machines  

Science Conference Proceedings (OSTI)

The W- andWp-methods are the basis for conformance testing from a deterministic finite state machine (DFSM) when the conformance relation considered is equivalence. However, many DFSM applications use only input sequences of limited length. In such cases, ... Keywords: Finite state machines, Specification-based testing, Test selection, W-method, Wp-method

Florentin Ipate

2010-03-01T23:59:59.000Z

302

Milling Machine Replacement Project (4587), 5/11/2012  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Milling Machine Replacement Projects (4587) Milling Machine Replacement Projects (4587) Program or Field Office: Y-12 Site Office Location(s) (City/County/State): Oak Ridge, Anderson County, Tennessee Proposed Action Description: Submit by E-mail The proposed action is to replace two large milling machines with two new medium sized CNC milling machines. The new machines will be connected to the digital network communication (DNC) system. Categorical Exclusion(s) Applied: 81.31 -Installation or relocation of machinery and equipment For the complete DOE National Environmental Policy Act regulations regarding categorical exclusions, including the full text of each categorical exclusion, see Subpart D of 10 CFR Part 1021. Regulatory Requirements in 10 CFR 1021.410(b): (See full text in regulation)

303

Traction sheave elevator, hoisting unit and machine space  

DOE Patents (OSTI)

Traction sheave elevator consisting of an elevator car moving along elevator guide rails, a counterweight moving along counterweight guide rails, a set of hoisting ropes (3) on which the elevator car and counterweight are suspended, and a drive machine unit (6) driving a traction sheave (7) acting on the hoisting ropes (3) and placed in the elevator shaft. The drive machine unit (6) is of a flat construction. A wall of the elevator shaft is provided with a machine space with its open side facing towards the shaft, the essential parts of the drive machine unit (6) being placed in the space. The hoisting unit (9) of the traction sheave elevator consists of a substantially discoidal drive machine unit (6) and an instrument panel (8) mounted on the frame (20) of the hoisting unit.

Hakala, Harri (Hyvinkaa, FI); Mustalahti, Jorma (Hyvinkaa, FI); Aulanko, Esko (Kerava, FI)

2000-01-01T23:59:59.000Z

304

cast shop technology i  

Science Conference Proceedings (OSTI)

M.D. Hurd, L.J. Laviolette and M.E. Lewellyn. Mitigation of ... The Determination of the Exposure to Electromagnetic Fields in Aluminum Electrolysis [pp. 253-259

305

cast shop technology i  

Science Conference Proceedings (OSTI)

Upgradation of Alumina Refinery at Hindalco Renukoot (India) R.P. Shah and .... The Influence of Crude Oil Desalting on Calcined Coke Quality (abstract only)

306

cast shop technology i  

Science Conference Proceedings (OSTI)

Guy Leblanc, and Vincent J. Newberry. Laboratory Investigations About the Influence of Starting Conditions on Butt Curl and Swell of DC Cast Sheet Ingots [

307

Aluminum Cast Shop IV  

Science Conference Proceedings (OSTI)

Mar 6, 2013 ... The energy released from one kilogram of molten aluminium reacted with oxygen is equivalent to detonating 3 kilograms of trinitrotoluene ...

308

cast shop technology ii  

Science Conference Proceedings (OSTI)

Energy Efficiency Considerations on Monopolar Versus Bipolar Fused Salt .... Use of a Technical Audit to Improve the Safe Handling of Molten Materials [pp.

309

Online Shopping Tips  

Science Conference Proceedings (OSTI)

... Giant Texas Turkey (Feeds 75) $95.10, Texas Turkey (28 - 30 lb) (feeds 75) Maximum Price: $95.10 Unit Price: $3.17 per lb, Texas Turkey Unit Price ...

2012-01-30T23:59:59.000Z

310

Hybrid machine maintenance planning systems using case-based reasoning and evolution strategies  

Science Conference Proceedings (OSTI)

Machine failure prediction involves the processing of massive amounts of data, expert's knowledge of various types of machines, problems of noisy data and operation variability. The chief advantages of effective machine failure prediction are that it ...

Kan Yuen Sin / James Liu

2004-01-01T23:59:59.000Z

311

LTC vacuum blasting machine (metal): Baseline report  

SciTech Connect

The LTC coating removal technology was tested and is being evaluated at Florida International University (FIU) as a baseline technology. In conjunction with evaluation of efficiency and cost, this report covers the evaluation conducted for safety and health issues. It is a commercially available technology and has been used for various projects at locations throughout the country. The LTC coating removal system consisted of several hand tools, a Roto Peen scaler, and a needlegun. They are designed to remove coatings from steel, concrete, brick, and wood. These hand tools are used with the LTC PTC-6 vacuum system to capture dust and debris as removal of the coating takes place. The safety and health evaluation during the testing demonstration focused on two main areas of exposure: dust and noise. The dust exposure was minimal but noise exposure was significant. Further testing for each exposure is recommended because of the environment where the testing demonstration took place. It is feasible that the dust and noise levels will be higher in an enclosed operating environment of different construction. In addition, other areas of concern found were arm-hand vibration, whole-body vibration, ergonomics, heat stress, tripping hazards, electrical hazards, machine guarding, and lockout/tagout.

1997-07-31T23:59:59.000Z

312

LTC vacuum blasting machine (concrete): Baseline report  

SciTech Connect

The LTC shot blast technology was tested and is being evaluated at Florida International University (FIU) as a baseline technology. In conjunction with FIU`s evaluation of efficiency and cost, this report covers the evaluation conducted for safety and health issues. It is a commercially available technology and has been used for various projects at locations throughout the country. The LTC 1073 Vacuum Blasting Machine uses a high-capacity, direct-pressure blasting system which incorporates a continuous feed for the blast media. The blast media cleans the surface within the contained brush area of the blast. It incorporates a vacuum system which removes dust and debris from the surface as it is blasted. The safety and health evaluation during the testing demonstration focused on two main areas of exposure: dust and noise. Dust exposure during maintenance activities was minimal, but due to mechanical difficulties dust monitoring could not be conducted during operation. Noise exposure was significant. Further testing for each of these exposures is recommended because of the outdoor environment where the testing demonstration took place. This may cause the results to be inaccurate. It is feasible that the dust and noise levels will be higher in an enclosed environment. In addition, other safety and health issues found were ergonomics, heat stress, tripping hazards, electrical hazards, lockout/tagout, and arm-hand vibration.

1997-07-31T23:59:59.000Z

313

Classification of Images Using Support Vector Machines  

E-Print Network (OSTI)

Support Vector Machines (SVMs) are a relatively new supervised classification technique to the land cover mapping community. They have their roots in Statistical Learning Theory and have gained prominence because they are robust, accurate and are effective even when using a small training sample. By their nature SVMs are essentially binary classifiers, however, they can be adopted to handle the multiple classification tasks common in remote sensing studies. The two approaches commonly used are the One-Against-One (1A1) and One-Against-All (1AA) techniques. In this paper, these approaches are evaluated in as far as their impact and implication for land cover mapping. The main finding from this research is that whereas the 1AA technique is more predisposed to yielding unclassified and mixed pixels, the resulting classification accuracy is not significantly different from 1A1 approach. It is the authors conclusions that ultimately the choice of technique adopted boils down to personal preference and the uniquene...

Anthony, Gidudu; Tshilidzi, Marwala

2007-01-01T23:59:59.000Z

314

Muon Collider Machine-Detector Interface  

SciTech Connect

In order to realize the high physics potential of a Muon Collider (MC) a high luminosity of {mu}{sup +}{mu}{sup -}-collisions at the Interaction Point (IP) in the TeV range must be achieved ({approx}10{sup 34} cm{sup -2}s{sup -1}). To reach this goal, a number of demanding requirements on the collider optics and the IR hardware - arising from the short muon lifetime and from relatively large values of the transverse emittance and momentum spread in muon beams that can realistically be obtained with ionization cooling should be satisfied. These requirements are aggravated by limitations on the quadrupole gradients as well as by the necessity to protect superconducting magnets and collider detectors from muon decay products. The overall detector performance in this domain is strongly dependent on the background particle rates in various sub-detectors. The deleterious effects of the background and radiation environment produced by the beam in the ring are very important issues in the Interaction Region (IR), detector and Machine-Detector Interface (MDI) designs. This report is based on studies presented very recently.

Mokhov, Nikolai V.; /Fermilab

2011-08-01T23:59:59.000Z

315

Energy Consumption Characterization and Reduction Strategies for Milling Machine Tool Use  

E-Print Network (OSTI)

Cutting Condition on Power Consumption of Machine Tools, in:Energy Consumption Characterization and Reduction Strategiesand reducing the energy consumption of milling machine tools

Diaz, Nancy; E. Redelsheimer; Dornfeld, David

2011-01-01T23:59:59.000Z

316

Energy Consumption Characterization and Reduction Strategies for Milling Machine Tool Use  

E-Print Network (OSTI)

Part Orientation for Face Milling, in: Annals of the CIRP,2010): Environmental Analysis of Milling Machine Tool Use inand Reduction Strategies for Milling Machine Tool Use Nancy

Diaz, Nancy; E. Redelsheimer; Dornfeld, David

2011-01-01T23:59:59.000Z

317

Environmental Analysis of Milling Machine Tool Use in Various Manufacturing Environments  

E-Print Network (OSTI)

Environmental Analysis of Milling Machine Tool Use inHorvath, David Dornfeld Milling is a type of cutting processof a standard vertical milling machine tool. In this

Diaz, Nancy; Helu, Moneer; Jayanathan, Stephen; Chen, Yifen; Horvath, Arpad; Dornfeld, David

2010-01-01T23:59:59.000Z

318

Energy Consumption Characterization and Reduction Strategies for Milling Machine Tool Use  

E-Print Network (OSTI)

Energy Consumption Characterization and Reduction Strategiesand reducing the energy consumption of milling machine toolsGreen Machine Tools; Energy Consumption Reduction; Specific

Diaz, Nancy; E. Redelsheimer; Dornfeld, David

2011-01-01T23:59:59.000Z

319

Water spray ventilator system for continuous mining machines  

DOE Patents (OSTI)

The invention relates to a water spray ventilator system mounted on a continuous mining machine to streamline airflow and provide effective face ventilation of both respirable dust and methane in underground coal mines. This system has two side spray nozzles mounted one on each side of the mining machine and six spray nozzles disposed on a manifold mounted to the underside of the machine boom. The six spray nozzles are angularly and laterally oriented on the manifold so as to provide non-overlapping spray patterns along the length of the cutter drum.

Page, Steven J. (Pittsburgh, PA); Mal, Thomas (Pittsburgh, PA)

1995-01-01T23:59:59.000Z

320

Flotation machine and process for removing impurities from coals  

DOE Patents (OSTI)

The present invention is directed to a type of flotation machine that combines three separate operations in a single unit. The flotation machine is a hydraulic separator that is capable of reducing the pyrite and other mineral matter content of a coal. When the hydraulic separator is used with a flotation system, the pyrite and certain other minerals particles that may have been entrained by hydrodynamic forces associated with conventional flotation machines and/or by the attachment forces associated with the formation of microagglomerates are washed and separated from the coal.

Szymocha, Kazimierz (Edmonton, CA); Ignasiak, Boleslaw (Edmonton, CA); Pawlak, Wanda (Edmonton, CA); Kulik, Conrad (Newark, CA); Lebowitz, Howard E. (Mountain View, CA)

1997-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "210-s machine shop" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


321

Flotation machine and process for removing impurities from coals  

DOE Patents (OSTI)

The present invention is directed to a type of flotation machine that combines three separate operations in a single unit. The flotation machine is a hydraulic separator that is capable of reducing the pyrite and other mineral matter content of a coal. When the hydraulic separator is used with a flotation system, the pyrite and certain other minerals particles that may have been entrained by hydrodynamic forces associated with conventional flotation machines and/or by the attachment forces associated with the formation of microagglomerates are washed and separated from the coal.

Szymocha, Kazimierz (Edmonton, CA); Ignasiak, Boleslaw (Edmonton, CA); Pawlak, Wanda (Edmonton, CA); Kulik, Conrad (Newark, CA); Lebowitz, Howard E. (Mountain View, CA)

1995-01-01T23:59:59.000Z

322

System and method for cooling a superconducting rotary machine  

Science Conference Proceedings (OSTI)

A system for cooling a superconducting rotary machine includes a plurality of sealed siphon tubes disposed in balanced locations around a rotor adjacent to a superconducting coil. Each of the sealed siphon tubes includes a tubular body and a heat transfer medium disposed in the tubular body that undergoes a phase change during operation of the machine to extract heat from the superconducting coil. A siphon heat exchanger is thermally coupled to the siphon tubes for extracting heat from the siphon tubes during operation of the machine.

Ackermann, Robert Adolf (Schenectady, NY); Laskaris, Evangelos Trifon (Schenectady, NY); Huang, Xianrui (Clifton Park, NY); Bray, James William (Niskayuna, NY)

2011-08-09T23:59:59.000Z

323

Integrated Mirco-Machined Hydrogen Gas Sensors  

DOE Green Energy (OSTI)

The widespread use of hydrogen as both an industrial process gas and an energy storage medium requires fast, selective detection of hydrogen gas. This report discusses the development of a new type of solid-state hydrogen gas sensor that couples novel metal hydride thin films with a MEMS (Micro-Electro-Mechanical System) structure known as a micro-hotplate. In this project, Micro-hotplate structures were overcoated with engineered multilayers that serve as the active hydrogen-sensing layer. The change in electrical resistance of these layers when exposed to hydrogen gas was the measured sensor output. This project focused on achieving the following objectives: (1) Demonstrating the capabilities of micro-machined H2 sensors; (2) Developing an understanding of their performance; (3) Critically evaluating the utility and viability of this technology for life safety and process monitoring applications. In order to efficiently achieve these objectives, the following four tasks were identified: (1) Sensor Design and Fabrication; (2) Short Term Response Testing; (3) Long Term Behavior Investigation; (4) Systems Development. Key findings in the project include: The demonstration of sub-second response times to hydrogen; measured sensitivity to hydrogen concentrations below 200 ppm; a dramatic improvement in the sensor fabrication process and increased understanding of the processing properties and performance relationships of the devices; the development of improved sensing multilayers; and the discovery of a novel strain based hydrogen detection mechanism. The results of this program suggest that this hydrogen sensor technology has exceptional potential to meet the stringent demands of life safety applications as hydrogen utilization and infrastructure becomes more prevalent.

Frank DiMeoJr. Ing--shin Chen

2005-12-15T23:59:59.000Z

324

TENTH WORLD CONGRESS ON THE THEORY OF MACHINES AND MECHANISMS  

E-Print Network (OSTI)

for Intelligent Machines, 817 Sherbrooke W., Montreal, Quebec, H3A 2K6 Canada. email: johnh@cim.mcgill.ca, kourosh@cim.mcgill.ca, angeles@cim.mcgill.ca Keywords: approximate kinematic synthesis, design, structural error, function

Hayes, John

325

A case for high performance computing with virtual machines  

Science Conference Proceedings (OSTI)

Virtual machine (VM) technologies are experiencing a resurgence in both industry and research communities. VMs offer many desirable features such as security, ease of management, OS customization, performance isolation, check-pointing, and migration, ...

Wei Huang; Jiuxing Liu; Bulent Abali; Dhabaleswar K. Panda

2006-06-01T23:59:59.000Z

326

Induction machine stray loss from inter-bar currents  

E-Print Network (OSTI)

Stray load loss refers generally to the sources of induction machine loss not accounted for by typical calculations of primary or secondary copper loss, no load core loss, or friction and windage loss. Harmonic rotor bar ...

Englebretson, Steven Carl

2009-01-01T23:59:59.000Z

327

Enforcing performance isolation across virtual machines in xen  

Science Conference Proceedings (OSTI)

Virtual machines (VMs) have recently emerged as the basis for allocating resources in enterprise settings and hosting centers. One benefit of VMs in these environments is the ability to multiplex several operating systems on hardware based on dynamically ...

Diwaker Gupta; Ludmila Cherkasova; Rob Gardner; Amin Vahdat

2006-11-01T23:59:59.000Z

328

Simple Memory Machine Models for GPUs Koji Nakano  

E-Print Network (OSTI)

Simple Memory Machine Models for GPUs Koji Nakano Department of Information Engineering Hiroshima University Kagamiyama 1-4-1, Higashi Hiroshima, 739-8527 Japan Email: nakano@cs.hiroshima-u.ac.jp Abstract

Moreno Maza, Marc

329

Substrate denaturation and translocation by a proteolytic machine  

E-Print Network (OSTI)

Many AAA+ molecular machines generate power and drive cellular processes by harnessing energy from cycles of ATP hydrolysis. ClpX is a relatively simple AAA+ ATPase that powers regulated protein degradation by binding ...

Kenniston, Jon Anders

2005-01-01T23:59:59.000Z

330

A Machine Learning System for Recognizing Subclasses (Demo)  

SciTech Connect

Thematic information extraction from remote sensing images is a complex task. In this demonstration, we present *Miner machine learning system. In particular, we demonstrate an advanced subclass recognition algorithm that is specifically designed to extract finer classes from aggregate classes.

Vatsavai, Raju [ORNL

2012-01-01T23:59:59.000Z

331

Machine learning for host-based anomaly detection  

Science Conference Proceedings (OSTI)

Anomaly detection techniques complement, signature based methods for intrusion detection. Machine learning approaches are applied to anomaly detection for automated learning and detection. Traditional host-based anomaly detectors model system call sequences ...

Gaurav Tandon / Philip K. Chan

2008-01-01T23:59:59.000Z

332

Face occlusion detection for automated teller machine surveillance  

Science Conference Proceedings (OSTI)

Real time automatic alarm systems play an essential role in security management, as evidenced by the surveillance cameras installed in nearly all automated teller machines (ATMs). Whereas manual video surveillance requires constant staff monitoring, ...

Daw-Tung Lin; Ming-Ju Liu

2006-12-01T23:59:59.000Z

333

KCP relocates 18-ton machine | National Nuclear Security Administratio...  

National Nuclear Security Administration (NNSA)

8 a.m. and by lunchtime that day, it was in place at the NSC. The machine will undergo laser alignment and build test parts around mid-June. It will be ready for production again...

334

Designing a unified programming model for heterogeneous machines  

Science Conference Proceedings (OSTI)

While high-efficiency machines are increasingly embracing heterogeneous architectures and massive multithreading, contemporary mainstream programming languages reflect a mental model in which processing elements are homogeneous, concurrency is limited, ...

Michael Garland; Manjunath Kudlur; Yili Zheng

2012-11-01T23:59:59.000Z

335

Applications of machine learning: matching problems to tasks and methods  

Science Conference Proceedings (OSTI)

The terminology of Machine Learning and Data Mining methods does not always allow a simple match between practical problems and methods. While some problems look similar from the user's point of view, but require different methods to be solved, some ...

Maarten Van Someren; Tanja Urban?i?

2005-12-01T23:59:59.000Z

336

Water-Cooled Ice Machines, Purchasing Specifications for Energy...  

NLE Websites -- All DOE Office Websites (Extended Search)

Ice Makers. b) Measured in accordance with ARI Standard 810-2003. Does not include condenser water use. Buying Energy-Efficient Water-Cooled Ice Machines Several types of...

337

Simplified hybrid-secondary uncluttered machine and method ...  

An electric machine (40, 40') has a stator (43) and a rotor (46) and a primary air gap (48) has secondary coils (47c, 47d) separated from the rotor (46) by a ...

338

Development of magnetic induction machines for micro turbo machinery  

E-Print Network (OSTI)

This thesis presents the nonlinear analysis, design, fabrication, and testing of an axial-gap magnetic induction micro machine, which is a two-phase planar motor in which the rotor is suspended above the stator via mechanical ...

KöÅŸ er, Hür, 1976-

2002-01-01T23:59:59.000Z

339

Approximation algorithms for stochastic scheduling on unrelated machines  

E-Print Network (OSTI)

Motivated by problems in distributed computing, this thesis presents the first nontrivial polynomial time approximation algorithms for an important class of machine scheduling problems. We study the family of preemptive ...

Scott, Jacob (Jacob Healy)

2008-01-01T23:59:59.000Z

340

Logomatic Gmbh Grinding Machines Fabrication | Open Energy Information  

Open Energy Info (EERE)

Logomatic Gmbh Grinding Machines Fabrication Logomatic Gmbh Grinding Machines Fabrication Jump to: navigation, search Name Logomatic Gmbh Grinding Machines Fabrication Place Mainaschaff, Germany Zip D-63814 Sector Solar Product German manufacturer of capital equipment for semiconductor and solar industries; for solar, offers diamond cropping and squaring machines. Coordinates 49.97746°, 9.085379° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":49.97746,"lon":9.085379,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

Note: This page contains sample records for the topic "210-s machine shop" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


341

A Machine Learning Evaluation of an Artificial Immune System  

Science Conference Proceedings (OSTI)

ARTIS is an artificial immune system framework which contains several adaptive mechanisms. LISYS is a version of ARTIS specialized for the problem of network intrusion detection. The adaptive mechanisms of LISYS are characterized in terms of their machine-learning ...

Matthew Glickman; Justin Balthrop; Stephanie Forrest

2005-06-01T23:59:59.000Z

342

Machine Learning for the New York City Power Grid  

E-Print Network (OSTI)

Power companies can benefit from the use of knowledge discovery methods and statistical machine learning for preventive maintenance. We introduce a general process for transforming historical electrical grid data into ...

Rudin, Cynthia

343

Machine to machine (M2M) technology in demand responsive commercial buildings  

SciTech Connect

Machine to Machine (M2M) is a term used to describe the technologies that enable computers, embedded processors, smart sensors, actuators and mobile devices to communicate with one another, take measurements and make decisions--often without human intervention. M2M technology was applied to five commercial buildings in a test. The goal was to reduce electric demand when a remote price signal rose above a predetermine price. In this system, a variable price signal was generated from a single source on the Internet and distributed using the meta-language, XML (Extensible Markup Language). Each of five commercial building sites monitored the common price signal and automatically shed site-specific electric loads when the price increased above predetermined thresholds. Other than price signal scheduling, which was set up in advance by the project researchers, the system was designed to operate without human intervention during the two-week test period. Although the buildings responded to the same price signal, the communication infrastructures used at each building were substantially different. This study provides an overview of the technologies used at each building site, the price generator/server, and each link in between. Network architecture, security, data visualization and site-specific system features are characterized. The results of the test are discussed, including: functionality at each site, measurement and verification techniques, and feedback from energy managers and building operators. Lessons learned from the test and potential implications for widespread rollout are provided.

Watson, David S.; Piette, Mary Ann; Sezgen, Osman; Motegi, Naoya; ten Hope, Laurie

2004-08-01T23:59:59.000Z

344

Enhanced Interpretation of Electromagnetic Signature Analysis for Large Machines  

Science Conference Proceedings (OSTI)

This project developed and applied frequency domain models to enhance interpretation of electromagnetic signature analysis (EMSA) for large electrical generators. The project's rationale was to provide a prediction of the native frequency response of the winding calculated from machine dimensions and design data so that the positions of the resonances would be known a priore. This procedure allowed augmentation of an EMSA spectrum at the characteristic resonant frequencies of the machine in the interpret...

2010-11-16T23:59:59.000Z

345

Online Load Balancing on Unrelated Machines with Startup Costs  

E-Print Network (OSTI)

Motivated by applications in energy-efficient scheduling in data centers, Khuller, Li, and Saha introduced the {\\em machine activation} problem as a generalization of the classical optimization problems of set cover and load balancing on unrelated machines. In this problem, a set of $n$ jobs have to be distributed among a set of $m$ (unrelated) machines, given the processing time of each job on each machine, where each machine has a startup cost. The goal is to produce a schedule of minimum total startup cost subject to a constraint $\\bf L$ on its makespan. While Khuller {\\em et al} considered the offline version of this problem, a typical scenario in scheduling is one where jobs arrive online and have to be assigned to a machine immediately on arrival. We give an $(O(\\log (mn)\\log m), O(\\log m))$-competitive randomized online algorithm for this problem, i.e. the schedule produced by our algorithm has a makespan of $O({\\bf L} \\log m)$ with high probability, and a total expected startup cost of $O(\\log (mn)\\lo...

Azar, Yossi

2012-01-01T23:59:59.000Z

346

Homopolar machine for reversible energy storage and transfer systems  

DOE Patents (OSTI)

A homopolar machine designed to operate as a generator and motor in reversibly storing and transferring energy between the machine and a magnetic load coil for a thermo-nuclear reactor. The machine rotor comprises hollow thin-walled cylinders or sleeves which form the basis of the system by utilizing substantially all of the rotor mass as a conductor thus making it possible to transfer substantially all the rotor kinetic energy electrically to the load coil in a highly economical and efficient manner. The rotor is divided into multiple separate cylinders or sleeves of modular design, connected in series and arranged to rotate in opposite directions but maintain the supply of current in a single direction to the machine terminals. A stator concentrically disposed around the sleeves consists of a hollow cylinder having a number of excitation coils each located radially outward from the ends of adjacent sleeves. Current collected at an end of each sleeve by sleeve slip rings and brushes is transferred through terminals to the magnetic load coil. Thereafter, electrical energy returned from the coil then flows through the machine which causes the sleeves to motor up to the desired speed in preparation for repetition of the cycle. To eliminate drag on the rotor between current pulses, the brush rigging is designed to lift brushes from all slip rings in the machine.

Stillwagon, Roy E. (Ruffsdale, PA)

1981-01-01T23:59:59.000Z

347

Homopolar machine for reversible energy storage and transfer systems  

DOE Patents (OSTI)

A homopolar machine designed to operate as a generator and motor in reversibly storing and transferring energy between the machine and a magnetic load coil for a thermo-nuclear reactor. The machine rotor comprises hollow thin-walled cylinders or sleeves which form the basis of the system by utilizing substantially all of the rotor mass as a conductor thus making it possible to transfer substantially all the rotor kinetic energy electrically to the load coil in a highly economical and efficient manner. The rotor is divided into multiple separate cylinders or sleeves of modular design, connected in series and arranged to rotate in opposite directions but maintain the supply of current in a single direction to the machine terminals. A stator concentrically disposed around the sleeves consists of a hollow cylinder having a number of excitation coils each located radially outward from the ends of adjacent sleeves. Current collected at an end of each sleeve by sleeve slip rings and brushes is transferred through terminals to the magnetic load coil. Thereafter, electrical energy returned from the coil then flows through the machine which causes the sleeves to motor up to the desired speed in preparation for repetition of the cycle. To eliminate drag on the rotor between current pulses, the brush rigging is designed to lift brushes from all slip rings in the machine.

Stillwagon, Roy E. (South Huntington Township, Huntington County, PA)

1978-01-01T23:59:59.000Z

348

Precise global collision detection in multi-axis NC-machining  

Science Conference Proceedings (OSTI)

We introduce a new approach to the problem of collision detection in multi-axis NC-machining. Due to the directional nature (tool axis) of multi-axis NC-machining, space subdivision techniques are adopted from ray-tracing algorithms and are extended ... Keywords: 5-Axis machining, Collision detection and verification, Lower envelopes, NC-machining, Ray tracing, Space subdivision

Oleg Ilushin; Gershon Elber; Dan Halperin; Ron Wein; Myung-Soo Kim

2005-08-01T23:59:59.000Z

349

Application of Particle Swarm Optimization technique for achieving desired milled surface roughness in minimum machining time  

Science Conference Proceedings (OSTI)

Face milling is a widely used machining operation to produce various components. The finished component depends not only on the dimensional accuracy but also on the surface finish. The present method of selection of machining parameters by trial and ... Keywords: Face milling, Machining parameters, Machining time, Particle Swarm Optimization, Surface roughness

S. Bharathi Raja; N. Baskar

2012-04-01T23:59:59.000Z

350

A comparative study for content-based dynamic spam classification using four machine learning algorithms  

Science Conference Proceedings (OSTI)

The growth of email users has resulted in the dramatic increasing of the spam emails during the past few years. In this paper, four machine learning algorithms, which are Naive Bayesian (NB), neural network (NN), support vector machine (SVM) and relevance ... Keywords: Naïve Bayesian, Neural network, Relevance vector machine, Spam classification, Support vector machine

Bo Yu; Zong-ben Xu

2008-05-01T23:59:59.000Z

351

The Kelastic variable wall mining machine. Interim final report  

SciTech Connect

This machine cuts coal along a longwall face extending up to 500 feet by a rotating auger with bits. The machine also transports the coal that is cut acting as screw conveyor. By virtue of an integral shroud comprising part of the conveyor the machine is also amenable to a separation of the zones where men work from air being contaminated by dust and methane gas by the cutting action. Beginning as single intake air courses, the air separates at the working section where one split provides fresh air to the Occupied Zone (OZ) for human needs and the other split purges and carries away dust and methane from face fragmentation in the Cutting Zone (CZ). The attractiveness of the Variable Wall Mining Machine is that it addresses the limitations of current longwall mining equipment: it can consistently out-produce continuous mining machines and most longwall shearing machines. It also is amenable to configuring an environment, the dual-duct system, where the air for human breathing is separated from dust-laden ventilating air with methane mixtures. The objective of the research was to perform a mathematical and experimental study of the interrelationships of the components of the system so that a computer model could demonstrate the workings of the system in an animation program. The analysis resulted in the compilation of the parameters for three different configurations of a dual aircourse system of ventilating underground mines. In addressing the goal of an inherently safe mining system the dual-duct adaptation to the Variable Wall Mining Machine appears to offer the path to solution. The respirable dust problem is solvable; the explosive dust problem is nearly solvable; and the explosive methane problem can be greatly reduced. If installed in a highly gassy mine, the dual duct models would also be considerably less costly.

1995-11-12T23:59:59.000Z

352

Rotating electrical machines. Part 2: Methods for determining losses and efficiency of rotating electrical machinery from tests (excluding machines for traction vehicles)  

E-Print Network (OSTI)

Applies to d.c. machines and to a.c. synchronous and induction machines. The principles can be applied to other types of machines such as rotary converters, a.c. commutator motors and single-phase induction motors for which other methods of determining losses are used.

International Electrotechnical Commission. Geneva

1972-01-01T23:59:59.000Z

353

Mid States Tool and Machine Inc | Open Energy Information  

Open Energy Info (EERE)

and Machine Inc and Machine Inc Jump to: navigation, search Name Mid States Tool and Machine Inc Place decatur, Indiana Zip 46733 Sector Services Product Provides engineering and manufacturing, testing, delivery, and post-installation on-site services. Coordinates 33.23476°, -97.585979° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":33.23476,"lon":-97.585979,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

354

Manz Intech Machines Co Ltd | Open Energy Information  

Open Energy Info (EERE)

Intech Machines Co Ltd Intech Machines Co Ltd Jump to: navigation, search Name Manz Intech Machines Co Ltd Place Taoyuan, Taiwan Zip 320 Sector Solar Product Taiwan-based manufacturer producing wet-chemical process equipment for the LCD and PCB industries and for thin-film solar PV production. Coordinates 25.001909°, 121.304977° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":25.001909,"lon":121.304977,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

355

Silicon Micromachined Dimensional Calibration Artifact for Mesoscale Measurement Machines  

NLE Websites -- All DOE Office Websites (Extended Search)

Silicon Micromachined Dimensional Calibration Silicon Micromachined Dimensional Calibration Artifact for Mesoscale Measurement Machines 1 Silicon Micromachined Dimensional Calibration Artifact for Mesoscale Measurement Machines 2 Sandia National Laboratories PO Box 5800 Albuquerque, NM 87185 USA Hy D. Tran, PhD, PE Phone: (505)844-5417 Fax: (505)844-4372 hdtran@sandia.gov AFFIRMATION: I affirm that all information submitted as a part of, or supplemental to, this entry is a fair and accurate representation of this product. ___________________________________ Hy D. Tran Not a joint entry. Silicon Micromachined Dimensional Calibration Artifact for Mesoscale Measurement Machines The silicon hybrid artifact is an anisotropic-etched silicon standard that is used as a calibration reference artifact to calibrate vision-based and

356

International Business Machines Corp IBM | Open Energy Information  

Open Energy Info (EERE)

Machines Corp IBM Machines Corp IBM Jump to: navigation, search Name International Business Machines Corp (IBM) Place Armonk, New York Zip 10504 Sector Services Product IBM is a technology company supplying hardware, software and Information Technology services. Coordinates 41.119417°, -73.708388° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":41.119417,"lon":-73.708388,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

357

Be a Lean, Mean, Green Eating Machine | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Be a Lean, Mean, Green Eating Machine Be a Lean, Mean, Green Eating Machine Be a Lean, Mean, Green Eating Machine January 31, 2012 - 2:53pm Addthis Kristin Swineford Communication Specialist, Weatherization and Intergovernmental Programs Like most Americans, I watched the State of the Union to hear President Obama outline his goals for the year ahead, to understand his energy outlook and plans, and of course, to see what Michelle would be wearing (a stunning royal blue, of course). When listening to the President highlight his administration's clean energy initiatives, I couldn't help but remember the First Family's goals to reduce childhood obesity in America. By no surprise, the link between nationwide health improvement and energy efficiency efforts is strong. By reducing our demand for processed and imported foods, we can improve the

358

DOE - Office of Legacy Management -- Etna Machine Co - OH 28  

NLE Websites -- All DOE Office Websites (Extended Search)

Etna Machine Co - OH 28 Etna Machine Co - OH 28 FUSRAP Considered Sites Site: Etna Machine Co. (OH.28 ) Eliminated from further consideration under FUSRAP Designated Name: Not Designated Alternate Name: None Location: 3400 Maplewood Avenue , Toledo , Ohio OH.28-1 Evaluation Year: 1987 OH.28-1 Site Operations: Conducted swaging experiment to reduce the diameter of a hot-rolled uranium metal rod Research/Development and Testing on Uranium Metal in December 1950 (lasted only two days). OH.28-1 Site Disposition: Eliminated - Limited scope of activities performed there - Potential for residual radioactive contamination is considered remote OH.28-2 Radioactive Materials Handled: Yes Primary Radioactive Materials Handled: Uranium OH.28-1 Radiological Survey(s): None Indicated

359

Be a Lean, Mean, Green Eating Machine | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Be a Lean, Mean, Green Eating Machine Be a Lean, Mean, Green Eating Machine Be a Lean, Mean, Green Eating Machine January 31, 2012 - 2:53pm Addthis Kristin Swineford Communication Specialist, Weatherization and Intergovernmental Programs Like most Americans, I watched the State of the Union to hear President Obama outline his goals for the year ahead, to understand his energy outlook and plans, and of course, to see what Michelle would be wearing (a stunning royal blue, of course). When listening to the President highlight his administration's clean energy initiatives, I couldn't help but remember the First Family's goals to reduce childhood obesity in America. By no surprise, the link between nationwide health improvement and energy efficiency efforts is strong. By reducing our demand for processed and imported foods, we can improve the

360

Development of precision machining and inspection technology for structural ceramics  

SciTech Connect

Finish machining operations contribute the majority of the costs associated with fabricating high quality ceramic products. These components are typically used in harsh environments such as diesel engines, the defense industry, and automotive applications. The required finishing operations involve a variety of technology areas including process controls, process analysis, product certification, etc. and are not limited only to component grinding methods. The broad range of manufacturing problem solving expertise available in Oak Ridge provided resources that were far beyond what is available to the Coors manufacturing sites. Coors contributed equipment, such as the computer controls and part handling mechanisms associated with a state-of-the-art inspection machine plus operation-specific experience base. In addition, addressing these challenging tasks enabled Oak Ridge personnel to maintain familarity with rapidly advancing technologies, such as those associated with machine vision equipment, process monitoring techniques, and computer control systems.

Barkman, W.E.

1997-03-06T23:59:59.000Z

Note: This page contains sample records for the topic "210-s machine shop" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


361

Electric Discharge Machining (EDM) Projects (4584), 4/11/2012  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Electric Discharge Machining (EDM) Projects (4584) Electric Discharge Machining (EDM) Projects (4584) Program or Field Office: Y -12 Site Office Location(s) (Citv/Countv/State): Oak Ridge, Anderson County, Tennessee Proposed Action Description: Submit by E-mail The proposed action is to installation of oil submerged Electric Discharge Machining (EDM) for development and production use. Categorical Exclusion(s) Applied: 81.31 -Installation or relocation of machinery and equipment For the complete DOE National Environmental Policy Act regulations regarding categorical exclusions, including the full text of each categorical exclusion, see Subpart D of 10 CFR Part 1021. Regulatory Requirements in 10 CFR 1021.410(b): (See full text in regulation) [{Jrhe proposal fits within a class of actions that is listed in Appendix A orB to 10 CFR Part 1021, Subpart D.

362

Holographic Labeling And Reading Machine For Authentication And Security Appications  

DOE Patents (OSTI)

A holographic security label and automated reading machine for marking and subsequently authenticating any object such as an identification badge, a pass, a ticket, a manufactured part, or a package is described. The security label is extremely difficult to copy or even to read by unauthorized persons. The system comprises a holographic security label that has been created with a coded reference wave, whose specification can be kept secret. The label contains information that can be extracted only with the coded reference wave, which is derived from a holographic key, which restricts access of the information to only the possessor of the key. A reading machine accesses the information contained in the label and compares it with data stored in the machine through the application of a joint transform correlator, which is also equipped with a reference hologram that adds additional security to the procedure.

Weber, David C. (Rancho Santa Margarita, CA); Trolinger, James D. (Costa Mesa, CA)

1999-07-06T23:59:59.000Z

363

From jet fuel to electric power using a mesoscale, efficient Stirling cycle  

E-Print Network (OSTI)

Engineering Thesis: Development of the Machine Shop Instruction and the Stirling Engine Project for 2.670: M

Gomez, Alessandro

364

Cleaning of Workpieces  

Science Conference Proceedings (OSTI)

...and the filler metal. Shop dirt, paint, grease, oil, machine lubricants, processing chemicals, temperature-indicating sticks, marking crayons, oxide

365

Machine-learning algorithm aims to accelerate materials discovery | Argonne  

NLE Websites -- All DOE Office Websites (Extended Search)

Science Science Computing, Environment & Life Sciences Energy Engineering & Systems Analysis Photon Sciences Physical Sciences & Engineering Energy Frontier Research Centers Science Highlights Postdoctoral Researchers Machine-learning algorithm aims to accelerate materials discovery July 16, 2013 Tweet EmailPrint A research team led by Argonne Leadership Computing Facility computational chemist Anatole von Lilienfeld is developing an algorithm that combines quantum chemistry with machine learning (artificial intelligence) to enable atomistic simulations that predict the properties of new materials with unprecedented speed. From innovations in medicine to novel materials for next-generation batteries, this approach could greatly accelerate the pace of materials discovery, with high-performance

366

Control coil arrangement for a rotating machine rotor  

DOE Patents (OSTI)

A rotating machine (e.g., a turbine, motor or generator) is provided wherein a fixed solenoid or other coil configuration is disposed adjacent to one or both ends of the active portion of the machine rotor for producing an axially directed flux in the active portion so as to provide planar axial control at single or multiple locations for rotor balance, levitation, centering, torque and thrust action. Permanent magnets can be used to produce an axial bias magnetic field. The rotor can include magnetic disks disposed in opposed, facing relation to the coil configuration.

Shah, Manoj R. (Latham, NY); Lewandowsk, Chad R. (Amsterdam, NY)

2001-07-31T23:59:59.000Z

367

Gelcasting compositions having improved drying characteristics and machinability  

DOE Patents (OSTI)

A gelcasting composition has improved drying behavior, machinability and shelf life in the dried and unfired state. The composition includes an inorganic powder, solvent, monomer system soluble in the solvent, an initiator system for polymerizing the monomer system, and a plasticizer soluble in the solvent. Dispersants and other processing aides to control slurry properties can be added. The plasticizer imparts an ability to dry thick section parts, to store samples in the dried state without cracking under conditions of varying relative humidity, and to machine dry gelcast parts without cracking or chipping. A method of making gelcast parts is also disclosed.

Janney, Mark A. (Knoxville, TN); Walls, Claudia A. H. (Oak Ridge, TN)

2001-01-01T23:59:59.000Z

368

Control Coil Arrangement for a Rotating Machine Rotor  

DOE Patents (OSTI)

A rotating machine (e.g., a turbine, motor or generator) is provided wherein a fixed solenoid or other coil configuration is disposed adjacent to one or both ends of the active portion of the machine rotor for producing an axially directed flux in the active portion so as to provide planar axial control at single or multiple locations for rotor balance, levitation, centering, torque and thrust action. Permanent magnets can be used to produce an axial bias magnetic field. The rotor can include magnetic disks disposed in opposed, facing relation to the coil configuration.

Shah, Manoj R.; Lewandowski, Chad R.

1999-05-05T23:59:59.000Z

369

Aspects of surface generation in orthogonal ultraprecision machining  

SciTech Connect

The depth of the plastically deformed layer at the workpiece surface which resulted in the orthogonal ultraprecision machining of Cu over the range of uncut chip thicknesses of 0.01-10 {mu}m was investigated. Two tools with the same nominal geometry but with differing edge geometries were used to machine both Te-Cu and fine grain Cu. Tool edge geometries were characterized by atomic force microscopy, taking into account the AFM cantilever tip radius. Magnitudes of the measured depths appear to be consistent with values reported in the literature and those arrived at by simple analyses.

Lucca, D.A.; Seo, Y.W. [Oklahoma State Univ., Stillwater, OK (United States). School of Mechanical and Aerospace Engineering; Rhorer, R.L. [Los Alamos National Lab., NM (United States)

1994-10-01T23:59:59.000Z

370

Human versus machine in the topic distillation task  

E-Print Network (OSTI)

This paper reports on and discusses a set of user experiments using the TREC 2003 Web interactive track protocol. The focus is on comparing humans and machine algorithms in terms of performance in a topic distillation task. We also investigated the effect of the search results layout in supporting the users ’ effort. We have demonstrated that machines can perform nearly as well as people on the topic distillation task. Given a system tailored to the task there is significant performance improvement and finally, given a presentation that supports the task, there is strong user satisfaction.

Mingfang Wu; Gheorghe Muresan; Alistair Mclean; Muh-chyun (morris Tang; Ross Wilkinson; Yuelin Li; Hyuk-jin Lee; Nichloas J. Belkin

2004-01-01T23:59:59.000Z

371

Revised Finding of No Significant Impact for Expansion and Operation of the Central Shops Borrow Pit at the Savannah River Site (DOE/EA-1194)(10/29/03)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Revised Finding of No Significant Impact Revised Finding of No Significant Impact for Expansion and Operation of the Central Shops Borrow Pit at the Savannah River Site Agency: U. S. Department of Energy Action: Revised Finding of No Significant Impact Summary: The Department of Energy (DOE) prepared an environmental assessment (EA) (DOE/EA-1194) in 1997 for the expansion and operation of the existing Central Shops Borrow Pit (i.e., SRS Facility 632-G) at the Savannah River Site (SRS), located near Aiken, South Carolina. This EA was prepared in accordance with the National Environmental Policy Act (NEPA) of 1969, as amended; the requirements of the Council on Environmental Quality Regulations for Implementing NEPA (40 CFR 15400-1508); and the DOE Regulations for Implementing NEPA (10 CFR 1021). Based on the analyses in the EA, DOE determined that

372

The Cutting Edge of Modernity: Machine Tools in the United States and Germany 1930-1945  

E-Print Network (OSTI)

): Germany – see Figures 1 & 2; US – American Machinist (1930 and 1931, 1940, and 1945) and United States, Department of Labor, Bureau of Labor Statistics, Handbook 1951, p. 10, Table A-3. Of course, a simple comparison of the total machine tool stock may... .71 Forging machines 32,598 18,602 0.78 Milling machines 116,978 71,474 0.83 Pipe cutting and threading machines + Thread machines 42,142 27,531 0.89 Lathes 308,170 225,749 1.00 Presses (not forging presses) 174,379 130,303 1.02 Cutting-off machines 39,719 29...

Ristuccia, Cristiano A; Tooze, J Adam

2004-06-16T23:59:59.000Z

373

Two-dimensional finite element method simulation of a four-quadrant transducer prototype machine considering skewed slots  

Science Conference Proceedings (OSTI)

A four-quadrant transducer (4QT) electric machine is an integrated electric machine used for hybrid electric vehicles. In this article a 4QT prototype machine that is radially integrated by two permanent-magnet synchronous machines is analyzed. Skewed slots are adopted for the two machines

Ping Zheng; Peter Thelin; Erik Nordlund; Chandur Sadarangani

2006-01-01T23:59:59.000Z

374

Blast-induced ground vibration prediction using support vector machine  

Science Conference Proceedings (OSTI)

Ground vibrations induced by blasting are one of the fundamental problems in the mining industry and may cause severe damage to structures and plants nearby. Therefore, a vibration control study plays an important role in the minimization of environmental ... Keywords: Blast vibration, Coefficient of determination, Conventional vibration predictor equations, Mean absolute error, Support vector machine

Manoj Khandelwal

2011-07-01T23:59:59.000Z

375

ROSSLER NONLINEAR DYNAMICAL MACHINE FOR CRYPTOGRAPHY APPLICATIONS Sunil Pandey  

E-Print Network (OSTI)

of chemical kinetics. The Rossler system is described by a system of 3 coupled nonlinear ordinary differentialROSSLER NONLINEAR DYNAMICAL MACHINE FOR CRYPTOGRAPHY APPLICATIONS Sunil Pandey * M.Tech. (Info Sec Author e-mail: algosunil@yahoo.co.in ABSTRACT In many of the cryptography applications like password

International Association for Cryptologic Research (IACR)

376

Some problems of prepositional phrases in machine translation  

Science Conference Proceedings (OSTI)

Prepositions as functional words play an important role in the construction of phrases and sentences. They connect typically a noun or a pronoun to another word and show their relationships in a sentence. They are a kind of “small” word and ... Keywords: controlled language technique, disambiguation, equivalent, grammatical functions, machine translation (MT), prepositional phrase attachment (PP attachment), translation information

Xiaohong Wu; Sylviane Cardey; Peter Greenfield

2006-08-01T23:59:59.000Z

377

Induction of robust classifiers for web ontologies through kernel machines  

Science Conference Proceedings (OSTI)

The paper focuses on the task of approximate classification of semantically annotated individual resources in ontological knowledge bases. The method is based on classification models built through kernel methods, a well-known class of effective statistical ... Keywords: Individual classification, Inductive reasoning, Kernel methods, Ontology mining, Similarity, Support vector machines

Nicola Fanizzi; Claudia d'Amato; Floriana Esposito

2012-03-01T23:59:59.000Z

378

EMLTrust: An enhanced Machine Learning based Reputation System for MANETs  

Science Conference Proceedings (OSTI)

Many mission critical networks including MANETs for military communications and disaster relief communications rely on node cooperation. If malicious nodes gain access to such networks they can easily launch attacks, such as spreading viruses or spam, ... Keywords: Digital credentials, Fading Memories, Machine Learning, Trust management

Rehan Akbani; Turgay Korkmaz; G. V. Raju

2012-05-01T23:59:59.000Z

379

Catenation and Specialization for Tcl Virtual Machine Performance  

E-Print Network (OSTI)

Catenation and Specialization for Tcl Virtual Machine Performance Benjamin Vitale bv @ cs-in-time native-code compilation. In the context of the Tcl VM, we convert bytecodes to native Sparc code implementation. These are relatively long in Tcl, but dispatch is still a signif- icant overhead. However

Abdelrahman, Tarek S.

380

Network anomaly detection with the restricted Boltzmann machine  

Science Conference Proceedings (OSTI)

With the rapid growth and the increasing complexity of network infrastructures and the evolution of attacks, identifying and preventing network abuses is getting more and more strategic to ensure an adequate degree of protection from both external and ... Keywords: Anomaly detection, Energy-based models, Intrusion detection, Restricted Boltzmann machine, Semi-supervised learning

Ugo Fiore, Francesco Palmieri, Aniello Castiglione, Alfredo De Santis

2013-12-01T23:59:59.000Z

Note: This page contains sample records for the topic "210-s machine shop" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


381

Pools of virtual boxes: building campus grids with virtual machines  

Science Conference Proceedings (OSTI)

A campus grid is a critical component of research cyberinfrastructure. A grid facilitates resource sharing, improving collaboration and increasing the capability to address large scale scientific and engineering problems. Resources comprising a grid ... Keywords: campus grid, deployment, distributed computing, high throughput computing, virtual machines, virtualization

David J. Herzfeld; Lars E. Olson; Craig A. Struble

2010-06-01T23:59:59.000Z

382

Predicting electricity distribution feeder failures using machine learning susceptibility analysis  

E-Print Network (OSTI)

This work has been partly supported by a research contract from Consolidated Edison. A Machine Learning (ML) System known as ROAMS (Ranker for Open-Auto Maintenance Scheduling) was developed to create failure-susceptibility rankings for almost one thousand 13.8kV-27kV energy distribution feeder cables that supply electricity to the boroughs of New

Philip Gross; Albert Boulanger; Marta Arias; David Waltz; Philip M. Long; Charles Lawson; Roger Anderson; Matthew Koenig; Mark Mastrocinque; William Fairechio; John A. Johnson; Serena Lee; Frank Doherty; Arthur Kressner

2006-01-01T23:59:59.000Z

383

Robotics and machine learning in a core college curriculum  

Science Conference Proceedings (OSTI)

In recent years, there has been an increase of interest in Robotics and Machine Learning in our society. Since the early days of industrial robotics, robots have been introduced to numerous areas of our everyday lives, ranging from robots in medicine ...

Boris Kerkez

2008-10-01T23:59:59.000Z

384

Support Vector Machines Applied to a Combustion Process  

Science Conference Proceedings (OSTI)

The following research aims to make the characterization of flames in the combustion process in an industrial boiler fossil fuel composed of one burner. The characterization of the flames is performed by analysis of electrical signals that are obtained ... Keywords: Combustion, electromagnetic radiation, principal components analysis, statistical moments, support vector machines

Claudia I. Torres, Fernando Hernandez, Antonio Trejo, Guillermo Ronquillo

2012-11-01T23:59:59.000Z

385

Big data, lifelong machine learning and transfer learning  

Science Conference Proceedings (OSTI)

A major challenge in today's world is the Big Data problem, which manifests itself in Web and Mobile domains as rapidly changing and heterogeneous data streams. A data-mining system must be able to cope with the influx of changing data in a continual ... Keywords: big data, lifelong machine learning, transfer learning

Qiang Yang

2013-02-01T23:59:59.000Z

386

Dependency-Based Chinese-English Statistical Machine Translation  

Science Conference Proceedings (OSTI)

We present a Chinese-English Statistical Machine Translation (SMT) system based on dependency tree mappings. We use a state-of-the-art dependency parser to parse the English translation of the Penn Chinese Treebank to make it bilingual and then learn ...

Xiaodong Shi; Yidong Chen; Jianfeng Jia

2009-05-01T23:59:59.000Z

387

Expert system development for vibration analysis in machine condition monitoring  

Science Conference Proceedings (OSTI)

Expert systems can be adapted for machine condition monitoring data interpretation due to the ability to identify systematic reasoning processes. As vibration analysis in condition monitoring is still generally performed by highly trained professionals, ... Keywords: Condition monitoring, Expert system, Vibration analysis

Stephan Ebersbach; Zhongxiao Peng

2008-01-01T23:59:59.000Z

388

Discrete element modeling of machine-manure interactions  

Science Conference Proceedings (OSTI)

The discrete element method (DEM) was applied to the study of the machine-product interactions occurring in manure handling and land application equipment. Two types of conveying systems (scraper and 4-auger system) were modeled along with a hopper and ... Keywords: Conveying systems, Discrete element method (DEM), Flow rate, Manure, Numerical modeling, Specific energy, Spreader

H. Landry; C. Laguë; M. Roberge

2006-06-01T23:59:59.000Z

389

Simulation of doubly-fed machine with improved wind turbine  

Science Conference Proceedings (OSTI)

Most of wind turbines use induction generators that are very reliable with low costs [2], but when it is straightly connected to the grid, maximum power is not accessible [1] and only a few change of speed between maximum speed and synchronous speed ... Keywords: doubly-fed machine, gearbox ratio, high speed shaft, low speed shaft, wind turbine

Hengameh Kojooyan Jafari

2009-02-01T23:59:59.000Z

390

Aquatic weed automatic classification using machine learning techniques  

Science Conference Proceedings (OSTI)

Aquatic weed control through chemical products has attracted much attention in the last years, mainly because of the ecological disorder caused by such plants, and also the consequences to the economical activities. However, this kind of control has ... Keywords: Aquatic weed, Artificial neural networks, Naïve Bayes, Optimum-path forest, Shape analysis, Support vector machines

LuíS A. M. Pereira; Rodrigo Y. M. Nakamura; Guilherme F. S. De Souza; Dagoberto Martins; JoãO P. Papa

2012-09-01T23:59:59.000Z

391

Improved Rooftop Detection in Aerial Images with Machine Learning  

Science Conference Proceedings (OSTI)

In this paper, we examine the use of machine learning to improve a rooftop detection process, one step in a vision system that recognizes buildings in overhead imagery. We review the problem of analyzing aerial images and describe an existing system ... Keywords: applications of learning, evaluation of algorithms, learning for computer vision, supervised learning

M. A. Maloof; P. Langley; T. O. Binford; R. Nevatia; S. Sage

2003-10-01T23:59:59.000Z

392

Efficient virtual machine support of runtime structural reflection  

Science Conference Proceedings (OSTI)

Increasing trends towards adaptive, distributed, generative and pervasive software have made object-oriented dynamically typed languages become increasingly popular. These languages offer dynamic software evolution by means of reflection, facilitating ... Keywords: Dynamically typed languages, JIT compilation, Prototype-based object-oriented model, SSCLI, Structural reflection, Virtual machine

Francisco Ortin; Jose Manuel Redondo; J. Baltasar García Perez-Schofield

2009-08-01T23:59:59.000Z

393

Using machine learning to predict catastrophes in dynamical systems  

Science Conference Proceedings (OSTI)

Nonlinear dynamical systems, which include models of the Earth's climate, financial markets and complex ecosystems, often undergo abrupt transitions that lead to radically different behavior. The ability to predict such qualitative and potentially disruptive ... Keywords: 37B30, 37N99, 65P99, 68T05, Conley index, Dynamical systems, Machine learning

Jesse Berwald; Tomáš Gedeon; John Sheppard

2012-03-01T23:59:59.000Z

394

Machine learning for event selection in high energy physics  

Science Conference Proceedings (OSTI)

The field of high energy physics aims to discover the underlying structure of matter by searching for and studying exotic particles, such as the top quark and Higgs boson, produced in collisions at modern accelerators. Since such accelerators are extraordinarily ... Keywords: Event selection, Evolutionary computation, High energy physics, Machine learning, Neural networks

Shimon Whiteson; Daniel Whiteson

2009-12-01T23:59:59.000Z

395

Machine Vision Analysis of the Energy Efficiency of Intermodal Trains  

E-Print Network (OSTI)

intermodal terminal mangers' feedback on loading performance for trains and be integrated into the software1 Machine Vision Analysis of the Energy Efficiency of Intermodal Trains YUNG-CHENG (REX) LAI JOHN M of constraints imposed by equipment design and diversity, there are often large gaps between intermodal loads

Barkan, Christopher P.L.

396

Virtual Machine Services: An Opportunity for Hardware Customization  

E-Print Network (OSTI)

of transistor count, which is leading to archi- tecture heterogeneity and customization. (2) Software developers (Virtual Machine), which executes services such as profiling, compilation, scheduling, and memory for potential improvements in energy through the use of hardware heterogeneity. This paper uses systematic

McKinley, Kathryn S.

397

Control system for an interior permanent magnet synchronous machine  

DOE Patents (OSTI)

A high performance, fully operational, four-quadrant control scheme is used in an interior permanent magnet synchronous machine. The machine operates smoothly with full performance in the constant-torque region as well as in the flux-weakening, constant-power region in both directions of motion. The transition between the constant-torque and constant-power regions is very smooth under all conditions of operation. Control in the constant-torque region is based on a vector or field-oriented technique, with the direct-axis aligned with the total stator flux, whereas constant-power region control is accomplished by orientation of the torque angle of the impressed square-wave voltage through the feedforward vector rotator. In a preferred embodiment, the control system employs a digital distributed microcomputer controller arrangement which relies upon various precisely estimated feedback signals, such as torque, flux, etc. The control scheme includes an outer torque control loop primarily for traction type applications, but also contemplates speed and position control loops for various industrial drives. A 70 hp drive system using a Neodymium-Iron-Boron permanent magnet machine and transistor pulse width modulating inverter has been designed and successfully tested. This control scheme also has application in controlling surface permanent magnet machines. 16 figs.

Bose, B.K.

1988-10-12T23:59:59.000Z

398

Energy management for hypervisor-based virtual machines  

E-Print Network (OSTI)

Current approaches to power management are based on operating systems with full knowledge of and full control over the underlying hardware; the distributed nature of multi-layered virtual machine environments renders such approaches insufficient. In this paper, we present a novel framework for energy management in modular, multi-layered operating system structures. The framework provides a unified model to partition and distribute energy, and mechanisms for energy-aware resource accounting and allocation. As a key property, the framework explicitly takes the recursive energy consumption into account, which is spent, e.g., in the virtualization layer or subsequent driver components. Our prototypical implementation targets hypervisor-based virtual machine systems and comprises two components: a host-level subsystem, which controls machine-wide energy constraints and enforces them among all guest OSes and service components, and, complementary, an energy-aware guest operating system, capable of fine-grained applicationspecific energy management. Guest level energy management thereby relies on effective virtualization of physical energy effects provided by the virtual machine monitor. Experiments with CPU and disk devices and an external data acquisition system demonstrate that our framework accurately controls and stipulates the power consumption of individual hardware devices, both for energy-aware and energyunaware guest operating systems. 1

Jan Stoess; Christian Lang; Frank Bellosa

2007-01-01T23:59:59.000Z

399

Micro rotary machine and methods for using same  

SciTech Connect

A micro rotary machine may include a micro actuator and a micro shaft coupled to the micro actuator. The micro shaft comprises a horizontal shaft and is operable to be rotated by the micro actuator. A micro tool is coupled to the micro shaft and is operable to perform work in response to motion of the micro shaft.

Stalford, Harold L. (Norman, OK)

2012-04-17T23:59:59.000Z

400

Anton, a special-purpose machine for molecular dynamics simulation  

Science Conference Proceedings (OSTI)

The ability to perform long, accurate molecular dynamics (MD) simulations involving proteins and other biological macro-molecules could in principle provide answers to some of the most important currently outstanding questions in the fields of biology, ... Keywords: bioinformatics, biomolecular system simulation, computational biology, computational drug design, molecular dynamics, protein folding, protein structure, special-purpose machine

David E. Shaw; Martin M. Deneroff; Ron O. Dror; Jeffrey S. Kuskin; Richard H. Larson; John K. Salmon; Cliff Young; Brannon Batson; Kevin J. Bowers; Jack C. Chao; Michael P. Eastwood; Joseph Gagliardo; J. P. Grossman; C. Richard Ho; Douglas J. Ierardi; István Kolossváry; John L. Klepeis; Timothy Layman; Christine McLeavey; Mark A. Moraes; Rolf Mueller; Edward C. Priest; Yibing Shan; Jochen Spengler; Michael Theobald; Brian Towles; Stanley C. Wang

2007-06-01T23:59:59.000Z

Note: This page contains sample records for the topic "210-s machine shop" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


401

Training of support vector machines with Mahalanobis kernels  

Science Conference Proceedings (OSTI)

Radial basis function (RBF) kernels are widely used for support vector machines. But for model selection, we need to optimize the kernel parameter and the margin parameter by time-consuming cross validation. To solve this problem, in this paper we propose ...

Shigeo Abe

2005-09-01T23:59:59.000Z

402

MALEF: Framework for distributed machine learning and data mining  

Science Conference Proceedings (OSTI)

Growing importance of distributed data mining techniques has recently attracted attention of researchers in multiagent domain. In this paper we present a novel framework MultiAgent Learning Framework (MALEF) designed for both the agent-based ... Keywords: MAS, agent-based systems, architectures, data mining, distributed machine learning, market-based approaches, multi-agent systems, multiagent learning frameworks, unsupervised clustering

Jan Tozicka; Michael Rovatsos; Michal Pechoucek; Stepan Urban

2008-02-01T23:59:59.000Z

403

Electromechanical coupling model for cutterhead driving system of shield machines  

Science Conference Proceedings (OSTI)

The synchronization of the cutterhead driving system of shield machines is affected by not only the nonlinearity of mechanical transmission mechanism and the characteristics of driving motors, but also their interaction. In this paper, dynamics of the ... Keywords: cutterhead, electromechanical coupling, synchronization

Jianzhong Sun; Ran Liu; Yaqin Luo; Wei Sun

2010-11-01T23:59:59.000Z

404

Micro Electro Discharge Machining of Electrically Nonconductive Ceramics  

Science Conference Proceedings (OSTI)

EDM is a known process for machining of hard and brittle materials. Due to its noncontact and nearly forceless behaviour, it has been introduced into micro manufacturing and through constant development it is now an important means for producing high-precision micro geometries. One restriction of EDM is its limitation to electrically conducting materials.Today many applications, especially in the biomedical field, make use of the benefits of ceramic materials, such as high strength, very low wear and biocompatibility. Common ceramic materials such as Zirconium dioxide are, due to their hardness in the sintered state, difficult to machine with conventional cutting techniques. A demand for the introduction of EDM to these materials could so far not be satisfied because of their nonconductive nature.At the Chemnitz University of Technology and the Fraunhofer IWU, investigations in the applicability of micro-EDM for the machining of nonconductive ceramics are being conducted. Tests are undertaken using micro-EDM drilling with Tungsten carbide tool electrodes and ZrO{sub 2} ceramic workpieces. A starting layer, in literature often referred to as 'assisting electrode' is used to set up a closed electric circuit to start the EDM process. Combining carbon hydride based dielectric and a specially designed low-frequency vibration setup to excite the workpiece, the process environment can be held within parameters to allow for a constant EDM process even after the starting layer is machined. In the experiments a cylindrical 120 {mu}m diameter Tungsten carbide tool electrode and Y{sub 2}O{sub 3}- and MgO- stabilized ZrO{sub 2} worpieces are used. The current and voltage signals of the discharges within the different stages of the process (machining of the starting layer, machining of the base material, transition stage) are recorded and their characteristics compared to discharges in metallic material. Additionally, the electrode feed is monitored. The influences of the process parameters are analysed with regard to the discharge type, electrode wear and process speed.Using the found parameters, micro geometries can be successfully machined into nonconductive Y{sub 2}O{sub 3}- and MgO- stabilized ZrO{sub 2} ceramic by means of micro-EDM.

Schubert, A. [Chair Micromanufacturing Technology, Faculty of Mechanical Engineering, Chemnitz University of Technology, 09107 Chemnitz (Germany); Fraunhofer Institute for Machine Tools and Forming Technology IWU, 09126 Chemnitz (Germany); Zeidler, H.; Hackert, M. [Chair Micromanufacturing Technology, Faculty of Mechanical Engineering, Chemnitz University of Technology, 09107 Chemnitz (Germany); Wolf, N. [Fraunhofer Institute for Machine Tools and Forming Technology IWU, 09126 Chemnitz (Germany)

2011-05-04T23:59:59.000Z

405

Application of Support Vector Machine (SVM) and Proximal Support Vector Machine (PSVM) for fault classification of monoblock centrifugal pump  

Science Conference Proceedings (OSTI)

Monoblock centrifugal pumps are widely used in a variety of applications. Defects and malfunctions (faults) of these pumps result in significant economic loss. Therefore, the pumps must be under constant monitoring. When a possible fault is detected, ... Keywords: CAV, PSVM, bearing faults, cavitation, decision trees, fault classification, fault diagnosis, impeller faults, monoblock centrifugal pumps, proximal SVM, seal faults, support vector machines, vibration signals

N. R. Sakthivel; V. Sugumaran; Binoy B. Nair

2010-12-01T23:59:59.000Z

406

Microsoft Word - ANL 2005 ESH - Volume II -FINAL FORMATTED...  

NLE Websites -- All DOE Office Websites (Extended Search)

described in the following three paragraphs. Dust-producing machine shop equipment (i.e., grinding wheels and belt sanders) is present in numerous laboratory office module machine...

407

Y-12 enters the 1980s  

NLE Websites -- All DOE Office Websites (Extended Search)

the nation's, and likely the world's, most precise machine shop. At the same time, the aging infrastructure and even some of the machine tools, foundry equipment, metal...

408

Analysis of electromechanical interactions in a flywheel system with a doubly fed induction machine  

E-Print Network (OSTI)

This paper analyzes the electromechanical inter-action in a flywheel system with a doubly fed induction machine, used for wind farm power smoothing or grid frequency response control. The grid-connected electrical machine ...

Ran, Li

409

A new method for crude oil price forecasting based on support vector machines  

Science Conference Proceedings (OSTI)

This paper proposes a new method for crude oil price forecasting based on support vector machine (SVM). The procedure of developing a support vector machine model for time series forecasting involves data sampling, sample preprocessing, training & ...

Wen Xie; Lean Yu; Shanying Xu; Shouyang Wang

2006-05-01T23:59:59.000Z

410

A Virtual Machine for a Type-omega Denotational Proof Language  

E-Print Network (OSTI)

In this thesis, I designed and implemented a virtual machine (VM) for a monomorphic variant of Athena, a type-omega denotational proof language (DPL). This machine attempts to maintain the minimum state required to ...

III, Teodoro Arvizo

2002-06-01T23:59:59.000Z

411

On the Performance of Informative Wavelets for Classification and Diagnosis of Machine Faults  

Science Conference Proceedings (OSTI)

This paper deals with an application of wavelets for feature extraction and classification of machine faults in a real-world machine data analysis environment. We have utilized informative wavelet algorithm to generate wavelets and subsequent coefficients ...

H. Ahmadi; R. Tafreshi; F. Sassani; G. Dumont

2001-12-01T23:59:59.000Z

412

A two-phase spherical electric machine for generating rotating uniform magnetic fields  

E-Print Network (OSTI)

This thesis describes the design and construction of a novel two-phase spherical electric machine that generates rotating uniform magnetic fields, known as a fluxball machine. Alternative methods for producing uniform ...

Lawler, Clinton T. (Clinton Thomas)

2007-01-01T23:59:59.000Z

413

Formulating Detergents and Personal Care ProductsChapter 6 Hand and Machine Dishwashing Products  

Science Conference Proceedings (OSTI)

Formulating Detergents and Personal Care Products Chapter 6 Hand and Machine Dishwashing Products Surfactants and Detergents eChapters Surfactants - Detergents Press Downloadable pdf of\tChapter 6 Hand and Machine

414

Revisiting Computational Thermodynamics through Machine Learning of High-Dimensional Data  

Science Conference Proceedings (OSTI)

A new perspective on alloy thermodynamics computation uses data-driven analysis and machine learning for the design and discovery of materials. The focus is on an integrated machine-learning framework

2013-01-01T23:59:59.000Z

415

Machine Design Op.miza.on Based on Finite Element Analysis using  

E-Print Network (OSTI)

Toyota Prius! Nissan Leaf! Chevy Volt! #12;WEMPEC 5/2/2012 Condor Week 2012 WJ - 4 EV Electric Machine

Wisconsin at Madison, University of

416

A strategy of investigation on the thermal behaviour of motorised spindles under high-speed machining  

Science Conference Proceedings (OSTI)

Motorised spindles used for high-speed machining are notorious for their sudden catastrophic failures at high speeds mainly due to bearing thermal problems. Loss of machining accuracy is another major problem due to thermal deformation of the spindle, ... Keywords: FEM, angular contact ball bearings, bearing temperature, external cooling, finite element method, heat dissipation modelling, high speed machining, machining accuracy, motor heat generation, motorised spindles, simulation, spindle nose deformation, thermal deformation

V. Prabhu Raja; P. R. Thyla; P. Radhakrishnan

2006-09-01T23:59:59.000Z

417

Advanced Flywheel and Ultracapacitors as Embedded Solutions for Advanced Machine Tools and Robotics  

Science Conference Proceedings (OSTI)

Providing the precision metal cutting and forming capabilities for manufacturing worldwide, automated machine tools are industry's workhorses. When voltage sags upset machine tools, manufacturing processes stop or malfunction, damaging the tool cutting head or machined part. These events result in lost production, increased cost of goods, and higher manufacturing costs. This EPRI research project is part of a continuation of a multiyear effort to make machine tools more robust to voltage sags through tec...

2003-03-12T23:59:59.000Z

418

A population-based variable neighborhood search for the single machine total weighted tardiness problem  

Science Conference Proceedings (OSTI)

This paper investigates the single machine total weighted tardiness problem, in which a set of independent jobs with distinct processing times, weights, and due dates are to be scheduled on a single machine to minimize the sum of weighted tardiness of ... Keywords: Single machine scheduling, Total weighted tardiness, Variable neighborhood search

Xianpeng Wang; Lixin Tang

2009-06-01T23:59:59.000Z

419

Financial Data Mining Based on Support Vector Machines and Ensemble Learning  

Science Conference Proceedings (OSTI)

With the rapid development of e-commerce, financial data mining has been one of the most important research topics in the data mining community. Support vector machines (SVMs) and ensemble learning are two popular techniques in the machine learning field. ... Keywords: Financial Data Mining, Support Vector Machines, Ensemble Learning

Shi Lei; Ma Xinming; Xi Lei; Hu Xiaohong

2010-05-01T23:59:59.000Z

420

The Design for Warp Knitting Machine Traversing Control System Based on DSP  

Science Conference Proceedings (OSTI)

On the basis of in-depth study of warp knitting machine traversing control system, this paper designs a warp knitting machine traversing electronic control system based on digital signal processor (DSP). This system takes a three-phase permanent magnet ... Keywords: warp knitting machine, traversing motion, linear motor, DSP

De-Jun Li; Le-Ping Xu

2009-12-01T23:59:59.000Z

Note: This page contains sample records for the topic "210-s machine shop" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


421

Studying a self-sustainable system by making a mind time machine  

Science Conference Proceedings (OSTI)

We present our pilot study on a special machine that self-sustains its rich dynamics in an open environment. We made a machine called "MTM" (Mind Time Machine) that runs all day long, receiving massive visual data from the environment, processing by ... Keywords: massive data, mind time, plasticity, sustainability

Takashi Ikegami

2010-09-01T23:59:59.000Z

422

Enhancing product performance in machining processes: statistical analysis and development of predictive models  

Science Conference Proceedings (OSTI)

Process parameters, tool geometry and operating conditions considerably influence the quality and the functional performance, including the service-life, of machined components. Surface characteristics of the machined products such as hardness and roughness ... Keywords: lubrication systems, predictive models, statistical analysis, sustainable machining

G. Rotella, S. Rizzuti, D. Umbrello

2013-07-01T23:59:59.000Z

423

2013 Rube Goldberg Machine Contest | Argonne National Laboratory  

NLE Websites -- All DOE Office Websites (Extended Search)

Rube Goldberg Machine Contest Rube Goldberg Machine Contest Rube Goldberg 2013 1 of 26 Rube Goldberg 2013 Maine South High School Team #2 Rube Goldberg 2013 1 of 26 Rube Goldberg 2013 Maine South High School Team #2 Rube Goldberg 2013 2 of 26 Rube Goldberg 2013 Joliet Central High School Team #1 Rube Goldberg 2013 3 of 26 Rube Goldberg 2013 Hoffman Estates High School Team #1 Rube Goldberg 2013 4 of 26 Rube Goldberg 2013 Maine South High School Team #2 Rube Goldberg 2013 5 of 26 Rube Goldberg 2013 Rube Goldberg 2013 6 of 26 Rube Goldberg 2013 Hoffman Estates High School Team #1 Rube Goldberg 2013 7 of 26 Rube Goldberg 2013 Hoffman Estates High School Team #1 Rube Goldberg 2013 8 of 26 Rube Goldberg 2013 Hoffman Estates High School Team #2 Rube Goldberg 2013 9 of 26 Rube Goldberg 2013 Maine South High School Team #2

424

List of Vending Machine Controls Incentives | Open Energy Information  

Open Energy Info (EERE)

Controls Incentives Controls Incentives Jump to: navigation, search The following contains the list of 64 Vending Machine Controls Incentives. CSV (rows 1 - 64) Incentive Incentive Type Place Applicable Sector Eligible Technologies Active APS - Energy Efficiency Solutions for Business (Arizona) Utility Rebate Program Arizona Commercial Industrial Institutional Local Government Retail Supplier Schools State Government Building Insulation Central Air conditioners Chillers Comprehensive Measures/Whole Building Custom/Others pending approval Energy Mgmt. Systems/Building Controls Lighting Lighting Controls/Sensors Motor VFDs Motors Programmable Thermostats Refrigerators LED Exit Signs Evaporative Coolers Vending Machine Controls Food Service Equipment Yes Alliant Energy Interstate Power and Light (Electric) - Business Energy Efficiency Rebate Programs (Iowa) Utility Rebate Program Iowa Commercial

425

OBSERVATION REPORT BendKing Pipe Bending Machine.doc  

NLE Websites -- All DOE Office Websites (Extended Search)

BENDKING PIPE BENDING MACHI\NE BENDKING PIPE BENDING MACHI\NE DEMONSTRATION Field Observation Report for December 3 - 4, 2001 Date Published: March 2002 Brian Meindinger, RMOTC PREPARED FOR THE U.S. DEPARTMENT OF ENERGY ROCKY MOUNTAIN OILFIELD TESTING CENTER 907 N. POPLAR, SUITE 150 CASPER, WY 82601 1-888-599-2200 Approval: RMOTC Manager_____________________________ Date:______________ Disclaimer This report was prepared as an account of work sponsored by an agency of the United States Government. Neither the United States Government nor any agency thereof, nor any of their employees, nor any of their contractors, subcontractors, or their employees makes any warranty, express or implied, or assumes any legal liability or responsibility for the accuracy, completeness, or any third party's use or the results of such use of any

426

Electron beam machining using rotating and shaped beam power distribution  

DOE Patents (OSTI)

An apparatus and method for electron beam (EB) machining (drilling, cutting and welding) that uses conventional EB guns, power supplies, and welding machine technology without the need for fast bias pulsing technology. The invention involves a magnetic lensing (EB optics) system and electronic controls to: 1) concurrently bend, focus, shape, scan, and rotate the beam to protect the EB gun and to create a desired effective power-density distribution, and 2) rotate or scan this shaped beam in a controlled way. The shaped beam power-density distribution can be measured using a tomographic imaging system. For example, the EB apparatus of this invention has the ability to drill holes in metal having a diameter up to 1000 .mu.m (1 mm or larger), compared to the 250 .mu.m diameter of laser drilling.

Elmer, John W. (Pleasanton, CA); O' Brien, Dennis W. (Livermore, CA)

1996-01-01T23:59:59.000Z

427

Simplified Hybrid-Secondary Uncluttered Machine And Method  

DOE Patents (OSTI)

An electric machine (40, 40') has a stator (43) and a rotor (46) and a primary air gap (48) has secondary coils (47c, 47d) separated from the rotor (46) by a secondary air gap (49) so as to induce a slip current in the secondary coils (47c, 47d). The rotor (46, 76) has magnetic brushes (A, B, C, D) or wires (80) which couple flux in through the rotor (46) to the secondary coils (47c, 47d) without inducing a current in the rotor (46) and without coupling a stator rotational energy component to the secondary coils (47c, 47d). The machine can be operated as a motor or a generator in multi-phase or single-phase embodiments. A method of providing a slip energy controller is also disclosed.

Hsu, John S [Oak Ridge, TN

2005-05-10T23:59:59.000Z

428

Permanent magnet machine with windings having strand transposition  

DOE Patents (OSTI)

This document discusses, among other things, a stator with transposition between the windings or coils. The coils are free from transposition to increase the fill factor of the stator slots. The transposition at the end connections between an inner coil and an outer coil provide transposition to reduce circulating current loss. The increased fill factor reduces further current losses. Such a stator is used in a dual rotor, permanent magnet machine, for example, in a compressor pump, wind turbine gearbox, wind turbine rotor.

Qu, Ronghai (Clifton Park, NY); Jansen, Patrick Lee (Scotia, NY)

2009-04-21T23:59:59.000Z

429

Radiator debris removing apparatus and work machine using same  

DOE Patents (OSTI)

A radiator assembly includes a finned radiator core and a debris removing apparatus having a compressed air inlet and at least one compressed air outlet configured to direct compressed air through the radiator core. A work machine such as a wheel loader includes a radiator and a debris removing apparatus coupled with on-board compressed air and having at least one pressurized gas outlet configured to direct a gas toward the face of the radiator.

Martin, Kevin L. (Washburn, IL); Elliott, Dwight E. (Chillicothe, IL)

2008-09-02T23:59:59.000Z

430

Augmenting Manual Dictionaries for Statistical Machine Translation Systems  

E-Print Network (OSTI)

We show that the usefulness of manually created dictionaries can be enhanced for a statistical machine translation system when new translations are automatically added which are simple morphological transformations (plural forms, different verb inflections) of the original. Further improvement is possible when assigning probabilities to the lexicon entries. We describe a method to do this on the basis of an automatically trained statistical lexicon. Experimental results are given for Chinese to English translation tasks and show a significant improvement in translation quality.

Stephan Vogel; Christian Monson

2004-01-01T23:59:59.000Z

431

Kinetic effects on ballooning modes in mirror machines  

SciTech Connect

A general procedure for examining the influence of kinetic effects on the stability of magnetohydrodynamic ballooning modes in mirror machines is presented. In particular, the basic kinetic ballooning mode equation for a nonaxisymmetric, arbitrary beta system with anisotropic pressure is derived. Considering a long-thin equilibrium typical of the tandem mirror, it is shown that this governing eigenmode equation reduces to a simple form independent of wave-particle resonant effects.

Tang, W.M.; Catto, P.J.

1981-07-01T23:59:59.000Z

432

Diamond tool machining of materials which react with diamond  

DOE Patents (OSTI)

Apparatus for the diamond machining of materials which detrimentally react with diamond cutting tools in which the cutting tool and the workpiece are chilled to very low temperatures. This chilling halts or retards the chemical reaction between the workpiece and the diamond cutting tool so that wear rates of the diamond tool on previously detrimental materials are comparable with the diamond turning of materials which do not react with diamond.

Lundin, Ralph L. (Los Alamos, NM); Stewart, Delbert D. (Los Alamos, NM); Evans, Christopher J. (Gaithersburg, MD)

1992-01-01T23:59:59.000Z

433

Simulation of Alpha-Channeling in Mirror Machines  

SciTech Connect

Applying ?-channeling techniques to mirror machines can significantly increase their effective reactivity, thus making open configurations more advantageous for practical fusion. A large fraction of ? particle energy can be extracted using rf waves. Effects employed to cool ? particles can also in principle be used to heat the fusion ions; the possibility to design a configuration of rf waves which could be used to perform both tasks is demonstrated.

A.I. Zhmoginov, N.J. Fisch

2008-03-17T23:59:59.000Z

434

Strategy making and power in environmental assessments. Lessons from the establishment of an out-of-town shopping centre in Vaesteras, Sweden  

SciTech Connect

This paper seeks to provide deeper insights into how EA ineffectiveness is produced in land use planning practice. This is explored in a study of local development planning in the city of Vaesteras, Sweden. The case in question is the development of a large out-of-town shopping centre, propelled by the establishment of a new IKEA furniture store. The Healey (2007) framework of planning as strategy making is applied as an analytical framework, together with a focus on power-knowledge relations. In the analysis, we identify a range of mechanisms that produced ineffectiveness by limiting the role of environmental knowledge throughout the planning process. The specific mechanisms we identified were related to the overall consensus perspective in local development strategies and plans, a lack of concretisation and integration of various policies and strategies, a range of exclusion mechanisms and an overall focus on mitigation and benefits of the process in question. In practice, these mechanisms were closely intertwined. Our main conclusion is, consequently, that increased effectiveness of EA would require fundamental transformation of the norms, frameworks and routines that implicitly and explicitly guide land use planning in practice. - Highlights: Black-Right-Pointing-Pointer We analyse how EA-ineffectiveness is produced in land use planning practice. Black-Right-Pointing-Pointer Several mechanisms produce EA-ineffectiveness throughout the whole planning process. Black-Right-Pointing-Pointer These mechanisms are often closely intertwined and mutually reinforcing each other. Black-Right-Pointing-Pointer Enhancing EA-effectiveness requires a fundamental shift of the norms, frameworks and routines shaping planning practice.

Isaksson, Karolina, E-mail: karolina.isaksson@vti.se [Mobility, Actors and Planning Processes (MAP), Swedish National Road and Transport Research Institute (VTI), 581 95 Linkoeping (Sweden); Storbjoerk, Sofie, E-mail: sofie.storbjork@liu.se [Department of Water and Environmental Studies (DWES) and Centre for Climate Science and Policy Research (CSPR), Linkoeping University, 581 83 Linkoeping (Sweden)

2012-04-15T23:59:59.000Z

435

Coordinate measuring machine test standard apparatus and method  

DOE Patents (OSTI)

A coordinate measuring machine test standard apparatus and method are disclosed which includes a rotary spindle having an upper phase plate and an axis of rotation, a kinematic ball mount attached to the phase plate concentric with the axis of rotation of the phase plate, a groove mounted at the circumference of the phase plate, and an arm assembly which rests in the groove. The arm assembly has a small sphere at one end and a large sphere at the other end. The small sphere may be a coordinate measuring machine probe tip and may have variable diameters. The large sphere is secured in the kinematic ball mount and the arm is held in the groove. The kinematic ball mount includes at least three mounting spheres and the groove is an angular locating groove including at least two locking spheres. The arm may have a hollow inner core and an outer layer. The rotary spindle may be a ratio reducer. The device is used to evaluate the measuring performance of a coordinate measuring machine for periodic recertification, including 2 and 3 dimensional accuracy, squareness, straightness, and angular accuracy. 5 figs.

Bieg, L.F.

1994-08-30T23:59:59.000Z

436

Muon Collider interaction region and machine-detector interface design  

Science Conference Proceedings (OSTI)

One of the key systems of a Muon Collider (MC) - seen as the most exciting option for the energy frontier machine in the post-LHC era - is its interaction region (IR). Designs of its optics, magnets and machine-detector interface are strongly interlaced and iterative. As a result of recent comprehensive studies, consistent solutions for the 1.5-TeV c.o.m. MC IR have been found and are described here. To provide the required momentum acceptance, dynamic aperture and chromaticity, an innovative approach was used for the IR optics. Conceptual designs of large-aperture high-field dipole and high-gradient quadrupole magnets based on Nb{sub 3}Sn superconductor were developed and analyzed in terms of the operating margin, field quality, mechanics, coil cooling and quench protection. Shadow masks in the interconnect regions and liners inside the magnets are used to mitigate the unprecedented dynamic heat deposition due to muon decays ({approx}0.5 kW/m). It is shown that an appropriately designed machine-detector interface (MDI) with sophisticated shielding in the detector has a potential to substantially suppress the background rates in the MC detector.

Mokhov, N.V.; Alexahin, Y.I.; Kashikhin, V.V.; Striganov, S.I.; Zlobin, A.V.; /Fermilab

2011-03-01T23:59:59.000Z

437

A Graphic Representation of States for Quantum Copying Machines  

E-Print Network (OSTI)

The aim of this paper is to introduce a new graphic representation of quantum states by means of a specific application: the analysis of two models of quantum copying machines. The graphic representation by diagrams of states offers a clear and detailed visualization of quantum information's flow during the unitary evolution of not too complex systems. The diagrams of states are exponentially more complex in respect to the standard representation and this clearly illustrates the discrepancy of computational power between quantum and classical systems. After a brief introductive exposure of the general theory, we present a constructive procedure to illustrate the new representation by means of concrete examples. Elementary diagrams of states for single-qubit and two-qubit systems and a simple scheme to represent entangled states are presented. Quantum copying machines as imperfect cloners of quantum states are introduced and the quantum copying machines of Griffiths and Niu and of Buzek and Hillery are analyzed, determining quantum circuits of easier interpretation. The method has indeed shown itself to be extremely successful for the representation of the involved quantum operations and it has allowed to point out the characteristic aspects of the quantum computations examined.

Sara Felloni; Giuliano Strini

2006-09-29T23:59:59.000Z

438

Coordinate measuring machine test standard apparatus and method  

DOE Patents (OSTI)

A coordinate measuring machine test standard apparatus and method which iudes a rotary spindle having an upper phase plate and an axis of rotation, a kinematic ball mount attached to the phase plate concentric with the axis of rotation of the phase plate, a groove mounted at the circumference of the phase plate, and an arm assembly which rests in the groove. The arm assembly has a small sphere at one end and a large sphere at the other end. The small sphere may be a coordinate measuring machine probe tip and may have variable diameters. The large sphere is secured in the kinematic ball mount and the arm is held in the groove. The kinematic ball mount includes at least three mounting spheres and the groove is an angular locating groove including at least two locking spheres. The arm may have a hollow inner core and an outer layer. The rotary spindle may be a ratio reducer. The device is used to evaluate the measuring performance of a coordinate measuring machine for periodic recertification, including 2 and 3 dimensional accuracy, squareness, straightness, and angular accuracy.

Bieg, Lothar F. (Louisville, CO)

1994-08-30T23:59:59.000Z

439

Method and apparatus for characterizing and enhancing the functional performance of machine tools  

DOE Patents (OSTI)

Disclosed are various systems and methods for assessing and improving the capability of a machine tool. The disclosure applies to machine tools having at least one slide configured to move along a motion axis. Various patterns of dynamic excitation commands are employed to drive the one or more slides, typically involving repetitive short distance displacements. A quantification of a measurable merit of machine tool response to the one or more patterns of dynamic excitation commands is typically derived for the machine tool. Examples of measurable merits of machine tool performance include workpiece surface finish, and the ability to generate chips of the desired length.

Barkman, William E; Babelay, Jr., Edwin F; Smith, Kevin Scott; Assaid, Thomas S; McFarland, Justin T; Tursky, David A; Woody, Bethany; Adams, David

2013-04-30T23:59:59.000Z

440

Method for producing fabrication material for constructing micrometer-scaled machines, fabrication material for micrometer-scaled machines  

DOE Patents (OSTI)

A method for producing fabrication material for use in the construction of nanometer-scaled machines is provided whereby similar protein molecules are isolated and manipulated at predetermined residue positions so as to facilitate noncovalent interaction, but without compromising the folding configuration or native structure of the original protein biomodules. A fabrication material is also provided consisting of biomodules systematically constructed and arranged at specific solution parameters.

Stevens, F.J.

1995-12-31T23:59:59.000Z

Note: This page contains sample records for the topic "210-s machine shop" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


441

Property:On-Site fabrication capability/equipment | Open Energy Information  

Open Energy Info (EERE)

On-Site fabrication capability/equipment On-Site fabrication capability/equipment Jump to: navigation, search Property Name On-Site fabrication capability/equipment Property Type Text Pages using the property "On-Site fabrication capability/equipment" Showing 25 pages using this property. (previous 25) (next 25) A Alden Large Flume + Full on-site carpentry, machine, and instrumentation shops Alden Small Flume + Full on-site carpentry, machine, and instrumentation shops Alden Tow Tank + Full on-site carpentry, machine, and instrumentation shops Alden Wave Basin + Full on-site carpentry, machine, and instrumentation shops C Chase Tow Tank + There is a machine shop in the Laboratory Conte Large Flume + Full carpentry shop with welding and machining capabilities Conte Small Flume + Full carpentry shop with welding and machining capabilities

442

Agile machining and inspection thrust area team-on-machine probing / compatibility assessment of Parametric Technology Corporation (PTC) pro/CMM DMIS with Zeiss DMISEngine.  

SciTech Connect

The charter goal of the Agile Machining and Inspection Thrust Area Team is to identify technical requirements, within the nuclear weapons complex (NWC), for Agile Machining and Inspection capabilities. During FY 2008, the team identified Parametric Technology Corporation (PTC) Pro/CMM as a software tool for use in off-line programming of probing routines--used for measurement--for machining and turning centers. The probing routine would be used for in-process verification of part geometry. The same Pro/CMM program used on the machine tool could also be employed for program validation / part verification using a coordinate measuring machine (CMM). Funding was provided to determine the compatibility of the Pro/CMM probing program with CMM software (Zeiss DMISEngine).

Wade, James Rokwel; Tomlinson, Kurt; Bryce, Edwin Anthony

2008-09-01T23:59:59.000Z

443

Job-Shop Scheduling in a Body Shop  

E-Print Network (OSTI)

sions between industrial robots have to be taken into ac- count. ... The real world application which motivated this article arises from welding on car bodies: Let J ...

444

SECTION 10-SHOP AND SHOP/LAB SAFETY INTRODUCTION  

E-Print Network (OSTI)

and abrasive blasting, slate work, diatomite calcination Diatomaceous earth Roofing and asphalt felt Filling is often used generically even when other materials such as such as coal and metal slags, steel shot

Selmic, Sandra

445

How small can thermal machines be? The smallest possible refrigerator  

E-Print Network (OSTI)

We investigate the fundamental dimensional limits to thermodynamic machines. In particular we show that it is possible to construct self-contained refrigerators (i.e. not requiring external sources of work) consisting of only a small number of qubits and/or qutrits. We present three different models, consisting of two qubits, a qubit and a qutrit with nearest-neighbour interactions, and a single qutrit respectively. We then investigate fundamental limits to their performance; in particular we show that it is possible to cool towards absolute zero.

Noah Linden; Sandu Popescu; Paul Skrzypczyk

2009-08-14T23:59:59.000Z

446

Time machines and traversable wormholes in modified theories of gravity  

E-Print Network (OSTI)

We review recent work on wormhole geometries in the context of modified theories of gravity, in particular, in f(R) gravity and with a nonminimal curvature-matter coupling, and in the recently proposed hybrid metric-Palatini theory. In principle, the normal matter threading the throat can be shown to satisfy the energy conditions and it is the higher order curvatures terms that sustain these wormhole geometries. We also briefly review the conversion of wormholes into time-machines, explore several of the time travel paradoxes and possible remedies to these intriguing side-effects in wormhole physics.

Francisco S. N. Lobo

2012-12-05T23:59:59.000Z

447

Stator for a rotating electrical machine having multiple control windings  

DOE Patents (OSTI)

A rotating electric machine is provided which includes multiple independent control windings for compensating for rotor imbalances and for levitating/centering the rotor. The multiple independent control windings are placed at different axial locations along the rotor to oppose forces created by imbalances at different axial locations along the rotor. The multiple control windings can also be used to levitate/center the rotor with a relatively small magnetic field per unit area since the rotor and/or the main power winding provides the bias field.

Shah, Manoj R. (Latham, NY); Lewandowski, Chad R. (Amsterdam, NY)

2001-07-17T23:59:59.000Z

448

Direct control of air gap flux in permanent magnet machines  

DOE Patents (OSTI)

A method and apparatus for field weakening in PM machines uses field weakening coils (35, 44, 45, 71, 72) to produce flux in one or more stators (34, 49, 63, 64), including a flux which counters flux normally produced in air gaps between the stator(s) (34, 49, 63, 64) and the rotor (20, 21, 41, 61) which carries the PM poles. Several modes of operation are introduced depending on the magnitude and polarity of current in the field weakening coils (35, 44, 45, 71, 72). The invention is particularly useful for, but not limited to, the electric vehicle drives and PM generators.

Hsu, John S. (Oak Ridge, TN)

2000-01-01T23:59:59.000Z

449

Stator for Rotating Electrical Machine Having Multiple Controlwindings  

DOE Patents (OSTI)

A rotating electric machine is provided which includes multiple independent control windings for compensating for rotor imbalances and for levitating/centering the rotor. The multiple independent control windings are placed at different axial locations along the rotor to oppose forces created by imbalances at different axial locations along the rotor. The multiple control windings can also be used to levitate/center the rotor with a relatively small magnetic field per unit area since the rotor and/or the main power winding provides the biasfield.

Shah, Manoj R.; Lewandowski, Chad R.

1999-05-05T23:59:59.000Z

450

Prototyping Faithful Execution in a Java virtual machine.  

SciTech Connect

This report presents the implementation of a stateless scheme for Faithful Execution, the design for which is presented in a companion report, ''Principles of Faithful Execution in the Implementation of Trusted Objects'' (SAND 2003-2328). We added a simple cryptographic capability to an already simplified class loader and its associated Java Virtual Machine (JVM) to provide a byte-level implementation of Faithful Execution. The extended class loader and JVM we refer to collectively as the Sandia Faithfully Executing Java architecture (or JavaFE for short). This prototype is intended to enable exploration of more sophisticated techniques which we intend to implement in hardware.

Tarman, Thomas David; Campbell, Philip LaRoche; Pierson, Lyndon George

2003-09-01T23:59:59.000Z

451

Machine tool accuracy characterization workshops. Final report, May 5, 1992--November 5 1993  

Science Conference Proceedings (OSTI)

The ability to assess the accuracy of machine tools is required by both tool builders and users. Builders must have this ability in order to predict the accuracy capability of a machine tool for different part geometry`s, to provide verifiable accuracy information for sales purposes, and to locate error sources for maintenance, troubleshooting, and design enhancement. Users require the same ability in order to make intelligent choices in selecting or procuring machine tools, to predict component manufacturing accuracy, and to perform maintenance and troubleshooting. In both instances, the ability to fully evaluate the accuracy capabilities of a machine tool and the source of its limitations is essential for using the tool to its maximum accuracy and productivity potential. This project was designed to transfer expertise in modern machine tool accuracy testing methods from LLNL to US industry, and to educate users on the use and application of emerging standards for machine tool performance testing.

NONE

1995-01-06T23:59:59.000Z

452

Methods, systems and apparatus for controlling operation of two alternating current (AC) machines  

SciTech Connect

A system is provided for controlling two alternating current (AC) machines via a five-phase PWM inverter module. The system comprises a first control loop, a second control loop, and a current command adjustment module. The current command adjustment module operates in conjunction with the first control loop and the second control loop to continuously adjust current command signals that control the first AC machine and the second AC machine such that they share the input voltage available to them without compromising the target mechanical output power of either machine. This way, even when the phase voltage available to either one of the machines decreases, that machine outputs its target mechanical output power.

Gallegos-Lopez, Gabriel (Torrance, CA); Nagashima, James M. (Cerritos, CA); Perisic, Milun (Torrance, CA); Hiti, Silva (Redondo Beach, CA)

2012-06-05T23:59:59.000Z

453

Cast Shop for Aluminum Production  

Science Conference Proceedings (OSTI)

Organizer(s), Trond Furu, Hydro ... Review at Several US Aluminum Die Cast Manufacturers Using Unique, Non-Wetting, Micro-Porous Refractory Products.

454

Cast Shop for Aluminum Production  

Science Conference Proceedings (OSTI)

Implementation of a Global Casthouse Furnace Energy Efficiency Program at Rio Tinto ... Optimised Re-melting by the Use of Low-temperature Oxyfuel at Hydro ...

455

MACHINING TECHNIQUES AND PROCEDURES FOR URANIUM, GRAPHITE, TITANIUM, ZIRCONIUM, THORIUM, TANTALUM, BERYLLIUM, BISMUTH, LITHIUM, AND STELLITE  

SciTech Connect

Techniqnes are presented which are applicable in machining materinls such as U, graphite, Ti, Zr, Th, Ta, Be, Bi, Li, and stellite. Included in the general considerations are factors related to machinability of the materials, operating condition of the machines, and the condition of the cutting tools. In addition, industrial hygtene and safety aspects are examined. The techniques for each material are discussed in detail, the greatest attention being focused on uranium. (J.R.D.)

Davis, C.

1952-11-01T23:59:59.000Z

456

Method and system for controlling a synchronous machine over full operating range  

DOE Patents (OSTI)

System and method for controlling a synchronous machine are provided. The method allows for calculating a stator voltage index. The method further allows for relating the magnitude of the stator voltage index against a threshold voltage value. An offset signal is generated based on the results of the relating step. A respective state of operation of the machine is determined. The offset signal is processed based on the respective state of the machine.

Walters, James E. (Carmel, IN); Gunawan, Fani S. (Westfield, IN); Xue, Yanhong (Westfield, IN)

2002-01-01T23:59:59.000Z

457

Methods, systems and apparatus for synchronous current regulation of a five-phase machine  

DOE Patents (OSTI)

Methods, systems and apparatus are provided for controlling operation of and regulating current provided to a five-phase machine when one or more phases has experienced a fault or has failed. In one implementation, the disclosed embodiments can be used to synchronously regulate current in a vector controlled motor drive system that includes a five-phase AC machine, a five-phase inverter module coupled to the five-phase AC machine, and a synchronous current regulator.

Gallegos-Lopez, Gabriel; Perisic, Milun

2012-10-09T23:59:59.000Z

458

MACHINING TECHNIQUES AND PROCEDURES FOR URANIUM, GRAPHITE, TITANIUM, ZIRCONIUM, THORIUM, TANTALUM, BERYLLIUM, BISMUTH, LITHIUM, AND STELLITE  

SciTech Connect

Techniqnes are presented which are applicable in machining materinls such as U, graphite, Ti, Zr, Th, Ta, Be, Bi, Li, and stellite. Included in the general considerations are factors related to machinability of the materials, operating condition of the machines, and the condition of the cutting tools. In addition, industrial hygtene and safety aspects are examined. The techniques for each material are discussed in detail, the greatest attention being focused on uranium.

Davis, C.

1952-11-04T23:59:59.000Z

459

Environmental Analysis of Milling Machine Tool Use in Various Manufacturing Environments  

E-Print Network (OSTI)

United States’s total energy usage [2]. Machining is an areacould reduce the overall energy usage since HVAC is energy

Diaz, Nancy; Helu, Moneer; Jayanathan, Stephen; Chen, Yifen; Horvath, Arpad; Dornfeld, David

2010-01-01T23:59:59.000Z

460

The role of intelligent machines on the future battlefield, circa 2030.  

E-Print Network (OSTI)

??The application of Intelligent Machine (IM) technology to the battlefield in future has the potential to revolutionise warfare. Converging trends and incentives are propelling this… (more)

Morton, Ben Robert

2009-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "210-s machine shop" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


461

Evaluating trade-offs between sustainability, performance, and cost of green machining technologies  

E-Print Network (OSTI)

that begins with the load profile on the machine toolcomponents. Because these load profiles were difficultmultifunction I/O card. The load profile was generated using

Helu, Moneer

2012-01-01T23:59:59.000Z

462

Evaluating Trade-Offs Between Sustainability, Performance, and Cost of Green Machining Technologies  

E-Print Network (OSTI)

that begins with the load profile on the machine toolcomponents. Because these load profiles were difficultmultifunction I/O card. The load profile was generated using

Helu, Moneer; Rühl, Jan; Dornfeld, David; Werner, Patrick; Lanza, Gisela

2011-01-01T23:59:59.000Z

463

A test machine for investigation of the strength of thin sheet materials ...  

Science Conference Proceedings (OSTI)

PRODUCTION SECTION. A TEST MACHINE FOR INVESTIGATION OF THE STRENGTH OF THIN. SHEET ~IATERIALS IN BIAXIAL TENSION IN THE 20-300 ~.

464

Numerical Simulation of Earth Pressure on Head Chamber of Shield Machine with FEM  

SciTech Connect

Model parameters of conditioned soils in head chamber of shield machine are determined based on tree-axial compression tests in laboratory. The loads acting on tunneling face are estimated according to static earth pressure principle. Based on Duncan-Chang nonlinear elastic constitutive model, the earth pressures on head chamber of shield machine are simulated in different aperture ratio cases for rotating cutterhead of shield machine. Relationship between pressure transportation factor and aperture ratio of shield machine is proposed by using aggression analysis.

Li Shouju; Kang Chengang [State Key Laboratory of structural analysis for industrial equipment, Dalian University of Technology, Dalian 116023 (China); Sun, Wei [School of Mechanical Engineering, Dalian University of Technology, Dalian 116023 (China); Shangguan Zichang [School of Civil and Hydraulic Engineering, Dalian University of Technology, Dalian 116023 (China); Institute of Civil Engineering, Dalian Fishery University, Dalian 116023 (China)

2010-05-21T23:59:59.000Z

465

ACCELERATED AGING STUDY OF MACHINE WINDING INSULATION UNDER AC AND HIGH FREQUENCY PULSE VOLTAGE APPLICATION.  

E-Print Network (OSTI)

?? It is common practice to perform accelerated aging with 60 Hz ac to determine the lifetime characteristics of insulation used in the machine. Comparable… (more)

Chalise, Sajal Raj

2010-01-01T23:59:59.000Z

466

Energy Usage Evaluation and Condition Monitoring for Electric Machines using Wireless Sensor Networks.  

E-Print Network (OSTI)

??Energy usage evaluation and condition monitoring for electric machines are important in industry for overall energy savings. Traditionally these functions are realized only for large… (more)

Lu, Bin

2006-01-01T23:59:59.000Z

467

Decision Support System (DSS) for Machine Selection: A Cost Minimization Model  

E-Print Network (OSTI)

Within any manufacturing environment, the selection of the production or assembly machines is part of the day to day responsibilities of management. This is especially true when there are multiple types of machines that can be used to perform each assembly or manufacturing process. As a result, it is critical to find the optimal way to select machines when there are multiple related assembly machines available. The objective of this research is to develop and present a model that can provide guidance to management when making machine selection decisions of parallel, non-identical, related electronics assembly machines. A model driven Decision Support System (DSS) is used to solve the problem with the emphasis in optimizing available resources, minimizing production disruption, thus minimizing cost. The variables that affect electronics product costs are considered in detail. The first part of the Decision Support System was developed using Microsoft Excel as an interactive tool. The second part was developed through mathematical modeling with AMPL9 mathematical programming language and the solver CPLEX90 as the optimization tools. The mathematical model minimizes total cost of all products using a similar logic as the shortest processing time (SPT) scheduling rule. This model balances machine workload up to an allowed imbalance factor. The model also considers the impact on the product cost when expediting production. Different scenarios were studied during the sensitivity analysis, including varying the amount of assembled products, the quantity of machines at each assembly process, the imbalance factor, and the coefficient of variation (CV) of the assembly processes. The results show that the higher the CV, the total cost of all products assembled increased due to the complexity of balancing machine workload for a large number of products. Also, when the number of machines increased, given a constant number of products, the total cost of all products assembled increased because it is more difficult to keep the machines balanced. Similar results were obtained when a tighter imbalance factor was used.

Mendez Pinero, Mayra I.

2009-05-01T23:59:59.000Z

468

Results of Water and Sediment Toxicity Tests and Chemical Analyses Conducted at the Central Shops Burning Rubble Pit Waste Unit, January 1999  

SciTech Connect

The Central Shops Burning Rubble Pit Operable Unit consists of two inactive rubble pits (631-1G and 631-3G) that have been capped, and one active burning rubble pit (631-2G), where wooden pallets and other non-hazardous debris are periodically burned. The inactive rubble pits may have received hazardous materials, such as asbestos, batteries, and paint cans, as well as non-hazardous materials, such as ash, paper, and glass. In an effort to determine if long term surface water flows of potentially contaminated water from the 631-1G, 631-3G, and 631-2G areas have resulted in an accumulation of chemical constituents at toxic levels in the vicinity of the settling basin and wetlands area, chemical analyses for significant ecological preliminary constituents of concern (pCOCs) were performed on aqueous and sediment samples. In addition, aquatic and sediment toxicity tests were performed in accordance with U.S. EPA methods (U.S. EPA 1989, 1994). Based on the results of the chemical analyses, unfiltered water samples collected from a wetland and settling basins located adjacent to the CSBRP Operable Unit exceed Toxicity Reference Values (TRVs) for aluminum, barium, chromium, copper, iron, lead, and vanadium at one or more of the four locations that were sampled. The water contained very high concentrations of clay particles that were present as suspended solids. A substantial portion of the metals were present as filterable particulates, bound to the clay particles, and were therefore not biologically available. Based on dissolved metal concentrations, the wetland and settling basin exceeded TRVs for aluminum and barium. However, the background reference location also exceeded the TRV for barium, which suggests that this value may be too low, based on local geochemistry. The detection limits for both total and dissolved mercury were higher than the TRV, so it was not possible to determine if the TRV for mercury was exceeded. Dissolved metal levels of chromium, copper, iron, lead and vanadium were below the TRVs. Metal concentrations in the sediment exceeded the TRVs for arsenic, chromium, copper, and mercury but not for antimony and lead. The results of the water toxicity tests indicated no evidence of acute toxicity in any of the samples. The results of the chronic toxicity tests indicated possible reproductive impairment at two locations. However, the results appear to be anomalous, since the toxicity was unrelated to concentration, and because the concentrations of pCOCs were similar in the toxic and the non-toxic samples. The results of the sediment toxicity tests indicated significant mortality in all but one sample, including the background reference sediment. When the results of the CSBRP sediment toxicity tests were statistically compared to the result from the background reference sediment, there was no significant mortality. These results suggest that the surface water and sediment at the CSBRP Operable Unit are not toxic to the biota that inhabit the wetland and the settling basin.

Specht, W.L.

1999-06-02T23:59:59.000Z

469

Magical Seals, Secure Voting Machines, and Other Fantasies  

NLE Websites -- All DOE Office Websites (Extended Search)

Magical Seals, Magical Seals, Secure Voting Machines, and Other Fantasies Roger G. Johnston, Ph.D., CPP Jon S. Warner, Ph.D. Vulnerability Assessment Team! Argonne National Laboratory! ! ! 630-252-6168 rogerj@anl.gov http://www.ne.anl.gov/capabilities/vat! Invited Talk for the Election Verification Network Meeting, Chicago, March 24-26, 2011 Argonne National Laboratory ~$738 million annual budget 1500 acres, 3400 employees, 4400 facility users, 1500 students R&D and technical assistance for government & industry Sponsors * DHS * DoD * DOS * IAEA * Euratom * DOE/NNSA * private companies * intelligence agencies * public interest organizations The VAT has done detailed vulnerability assessments on hundreds of different security

470

DOE - Office of Legacy Management -- American Machine and Foundry Co -  

NLE Websites -- All DOE Office Websites (Extended Search)

Buffalo - NY 63 Buffalo - NY 63 FUSRAP Considered Sites Site: American Machine and Foundry Co - Buffalo (NY.63 ) Eliminated from further consideration under FUSRAP Designated Name: Not Designated Alternate Name: AMF NY.63-1 Location: Buffalo , New York NY.63-1 Evaluation Year: 1990 NY.63-1 Site Operations: Design engineering for the development of electrical and mechanical controls. NY.63-1 Site Disposition: Eliminated - Potential for radioactive contamination considered remote. Radioactive material, if any was used at the site, would have been limited to test quantities. NY.63-2 Radioactive Materials Handled: None Indicated - test quantities, if any NY.63-1 Primary Radioactive Materials Handled: None Indicated, But Could Have Included Test Quantities of Finished Uranium Metal NY.63-1

471

MACHINE PROTECTION SYSTEM FOR CONCURRENT OPERATION OF RHIC AND BLIP.  

SciTech Connect

The Brookhaven 200MeV linac is a multipurpose machine used to inject low intensity polarized protons for RHIC (Relativistic Heavy Ion Collider), as well as to inject high intensity protons to BLIP (Brookhaven Linac Isotope Producer), a medical isotope production facility. If high intensity protons were injected to RHIC by mistake, administrative radiation limits could be exceeded or sensitive electronics could be damaged. In the past, the changeover from polarized proton to high intensity proton operation has been a lengthy process, thereby never allowing the two programs to run simultaneously. To remedy this situation and allow concurrent operation of RHIC and BLIP, an active interlock system has been designed to monitor current levels in the AGS using two current transformers with fail safe circuitry and associated electronics to inhibit beam to RHIC if high intensity currents are detected.

WILINSKI, M.; BELLAVIA, S.; GLENN, J.W.; MAUSNER, L.F.; UNGER, K.L.

2005-05-16T23:59:59.000Z

472

LTC American`s, Inc. vacuum blasting machine: Baseline report  

Science Conference Proceedings (OSTI)

The LTC shot blast technology was tested and is being evaluated at Florida International University (FIU) as a baseline technology. In conjunction with FIU`s evaluation of efficiency and cost, this report covers the evaluation conducted for safety and health issues. It is a commercially available technology and has been used for various projects at locations throughout the country. The LTC 1073 Vacuum Blasting Machine uses a high-capacity, direct-pressure blasting system which incorporates a continuous feed for the blast media. The blast media cleans the surface within the contained brush area of the blast. It incorporates a vacuum system which removes dust and debris from the surface as it is blasted. The safety and health evaluation during the testing focused on two main areas of exposure: dust and noise.

NONE

1997-07-31T23:59:59.000Z

473

Machine Learning for Host-based Anomaly Detection by  

E-Print Network (OSTI)

Anomaly detection techniques complement signature based methods for intrusion detection. Machine learning approaches are applied to anomaly detection for automated learning and detection. Traditional host-based anomaly detectors model system call sequences to detect novel attacks. This dissertation makes four key contributions to detect host anomalies. First, we present an unsupervised approach to clean training data using novel representations for system call sequences. Second, supervised learning with system call arguments and other attributes is proposed for enriched modeling. Third, techniques to increase model coverage for improved accuracy are presented. Fourth, we propose spatio-temporal modeling to detect suspicious behavior for mobile hosts. Experimental results on various data sets indicate that our techniques are more effective than traditional methods in capturing attack-based host anomalies. Additionally, our supervised methods create succint models and the computational overhead incurred is reasonable for an online anomaly detection system. iii Acknowledgements An ancient saying in Sanskrit: Matri devo bhava (revere your mother), pitri devo

Gaurav Tandon; Gaurav Tandon; Philip K. Chan, Ph.D.; Marius C. Silaghi, Ph.D.; Georgios C. Anagnostopoulos, Ph.D.; Gaurav Tandon; Dissertation Advisor; Philip K. Chan, Ph.D.

2008-01-01T23:59:59.000Z

474

A new DFM approach to combine machining and additive manufacturing  

E-Print Network (OSTI)

Design For Manufacturing (DFM) approaches aim to integrate manufacturability aspects during the design stage. Most of DFM approaches usually consider only one manufacturing process, but products competitiveness may be improved by designing hybrid modular products, in which products are seen as 3-D puzzles with modules realized aside by the best manufacturing process and further gathered. A new DFM system is created in order to give quantitative information during the product design stage of which modules will benefit in being machined and which ones will advantageously be realized by an additive process (such as Selective Laser Sintering or laser deposition). A methodology for a manufacturability evaluation in case of a subtractive or an additive manufacturing process is developed and implemented in a CAD software. Tests are carried out on industrial products from automotive industry.

Kerbrat, Olivier; Hascoët, Jean-Yves; 10.1016/j.compind.2011.04.003

2011-01-01T23:59:59.000Z

475

Diamond Wire Saw for Precision Machining of Laser Target Components  

SciTech Connect

The fabrication of precision laser targets requires a wide variety of specialized mesoscale manufacturing techniques. The diamond wire saw developed in this study provides the capability to precisely section meso-scale workpieces mounted on the assembly stations used by the Target Fabrication Group. This new capability greatly simplifies the fabrication of many types of targets and reduces the time and cost required to build the targets. A variety of materials are used to fabricate targets, including metals, plastics with custom designed chemical formulas, and aerogels of various densities. The materials are usually provided in the form of small pieces or cast rods that must be machined to the required shape. Many of these materials, such as metals and some plastics, can be trimmed using a parting tool on a diamond turning machine. However, other materials, such as aerogels and brittle materials, cannot be adequately cut with a parting tool. In addition, the geometry of the parts often requires that the workpieces be held in a special assembly station, which excludes the use of a parting tool. In the past, these materials were sectioned using a small, handheld coping saw that used a diamond-impregnated wire as a blade. This miniature coping saw was effective, but it required several hours to cut through certain materials. Furthermore, the saw was guided by hand and often caused significant damage to fragile aerogels. To solve these problems, the diamond wire saw shown in Figure 1 was developed. The diamond wire saw is designed to machine through materials that are mounted in the Target Fabrication Group's benchtop assembly stations. These assembly stations are the primary means of aligning and assembling target components, and there is often a need to machine materials while they are mounted in the assembly stations. Unfortunately, commercially available saws are designed for very different applications and are far too large to be used with the assembly stations. Therefore, a custom diamond wire saw was designed and constructed. The diamond wire saw cuts through workpieces using a continuous loop of diamond-impregnated wire of length 840 mm. The wire loop runs around several idler pulleys and is driven by a simple geared DC motor that rotates at 17 rpm. The linear speed of the wire is 107 inches/minute. The saw is oriented at an angle of 20{sup o} from horizontal, so the operator can view the wire through the cutout at the front end of the saw. When looking through a microscope or camera with a horizontal line of sight, the operator can clearly see the wire as it cuts through the workpiece, as shown in the right side of Figure 1. The saw is mounted on a two-axis stage that allows the operator to align the wire with the workpiece. To cut through the workpiece, the operator drives the wire through the workpiece by turning the feed micrometer. An image of the interior of the diamond wire saw appears in Figure 2. This picture was taken after removing the protective cover plate from the saw.

Bono, M J; Bennett, D W

2005-08-08T23:59:59.000Z

476

MRC Psycholinguistic Database: Machine Usable Dictionary, Version 2.00.  

E-Print Network (OSTI)

The MRC machine usable dictionary contains 150837 words with up to 26 linguistic and psycholinguistic attributes for each. The attributes are from sources that are publicly available, but difficult to obtain and structure into a single dictionary. Three utility programs are described which permit the selection of words defined by a set of specified attribute values, and the attribute values for a set of specified words. These programs permit the construction of word sets for psycholinguistic experiments which control for the attributes specified in the dictionary. The dictionary may also be of use to researchers in artificial intelligence and computer science who require psychological and linguistic descriptions of words. - 2 - Those wishing to construct word sets as stimuli for psycholinguistic experiments must take into account a large number of characteristics of the words (see Cutler, 1981; Whaley, 1978). The Medical Research Council (MRC) Psycholinguistic Database version 1, was...

Michael Wilson; Michael Wilson; Oxon Ox Qx; Philip Quinlan

1987-01-01T23:59:59.000Z

477

Feasibility Studies of Alpha-Channeling in Mirror Machines  

SciTech Connect

The linear magnetic trap is an attractive concept both for fusion reactors and for other plasma applications due to its relative engineering simplicity and high-beta operation. Applying the ?- channeling technique to linear traps, such as mirror machines, can benefit this concept by efficiently redirecting ? particle energy to fuel ion heating or by otherwise sustaining plasma confinement, thus increasing the effective fusion reactivity. To identify waves suitable for ?-channeling a rough optimization of the energy extraction rate with respect to the wave parameters is performed. After the optimal regime is identified, a systematic search for modes with similar parameters in mirror plasmas is performed, assuming quasi-longitudinal or quasi-transverse wave propagation. Several modes suitable for ? particle energy extraction are identified for both reactor designs and for proof- of-principle experiments.

A. I. Zhmoginov and N. J. Fisch

2010-03-19T23:59:59.000Z

478

Topical Report Tantalum – 2.5% Tungsten Machinability Testing  

Science Conference Proceedings (OSTI)

Protection Association (NFPA). NFPA 484, Standard for Combustible Metals, Chapter 9 Tantalum and Annex E, supplemental Information on Tantalum require cutting oil be used when machining tantalum because it burns at such a high temperature that it breaks down the water in a water-based metalworking fluid (MWF). The NFPA guide devotes approximately 20 pages to this material. The Kansas City Plant (KCP) uses Fuchs Lubricants Ecocut Base 44 LVC as a MWF. This is a highly chlorinated oil with a high flash point (above 200° F). The chlorine is very helpful in preventing BUE (Built Up Edge) that occurs frequently with this very gummy material. The Ecocut is really a MWF additive that Fuchs uses to add chlorinated fats to other non-chlorinated MWF.

L. J. Lazarus

2009-09-02T23:59:59.000Z

479

Identifying Energy-Efficient Concurrency Levels using Machine Learning  

SciTech Connect

Multicore microprocessors have been largely motivated by the diminishing returns in performance and the increased power consumption of single-threaded ILP microprocessors. With the industry already shifting from multicore to many-core microprocessors, software developers must extract more thread-level parallelism from applications. Unfortunately, low power-efficiency and diminishing returns in performance remain major obstacles with many cores. Poor interaction between software and hardware, and bottlenecks in shared hardware structures often prevent scaling to many cores, even in applications where a high degree of parallelism is potentially available. In some cases, throwing additional cores at a problem may actually harm performance and increase power consumption. Better use of otherwise limitedly beneficial cores by software components such as hypervisors and operating systems can improve system-wide performance and reliability, even in cases where power consumption is not a main concern. In response to these observations, we evaluate an approach to throttle concurrency in parallel programs dynamically. We throttle concurrency to levels with higher predicted efficiency from both performance and energy standpoints, and we do so via machine learning, specifically artificial neural networks (ANNs). One advantage of using ANNs over similar techniques previously explored is that the training phase is greatly simplified, thereby reducing the burden on the end user. Using machine learning in the context of concurrency throttling is novel. We show that ANNs are effective for identifying energy-efficient concurrency levels in multithreaded scientific applications, and we do so using physical experimentation on a state-of-the-art quad-core Xeon platform.

Curtis-Maury, M; Singh, K; Blagojevic, F; Nikolopoulos, D S; de Supinski, B R; Schulz, M; McKee, S A

2007-07-23T23:59:59.000Z

480

Fault diagnosis of regenerative water heater based-on multi-class support vector machines  

Science Conference Proceedings (OSTI)

The main idea of multi-class support vector machines (SVMs) is described. a multi-class model for regenerative water heater fault diagnosis is presented combining the fuzzy logic and SVMs. The typical faults set of regenerative water heater is built ... Keywords: fault diagnosis, fuzzy rules, regenerative water heater, steam turbine, support vector machines

Lei Wang; Rui-Qing Zhang

2009-08-01T23:59:59.000Z

Note: This page contains sample records for the topic "210-s machine shop" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


481

Applying RBR and CBR to develop a VR based integrated system for machining fixture design  

Science Conference Proceedings (OSTI)

A fixture is a special tool used to accurately and stably locate the workpiece during machining process. Proper fixture design improves the quality and production of parts and also facilitates the interchangeability of parts that is prevalent in much ... Keywords: Case-based reasoning (CBR), Machining fixture design, Rule-based reasoning (RBR), Virtual reality

Gaoliang Peng; Guangfeng Chen; Chong Wu; Hou Xin; Yang Jiang

2011-01-01T23:59:59.000Z

482

Modeling and experimental validation of internal faults in salient pole synchronous machines including space harmonics  

Science Conference Proceedings (OSTI)

Considering the space harmonics caused by the faulted windings, a simulation model of internal faults in salient pole synchronous machines is proposed in this paper. The model is based on the winding function approach, which makes no assumption for sinusoidal ... Keywords: Internal faults, Space harmonics, Synchronous machines, Winding function

X. Tu; L. -A. Dessaint; M. El Kahel; A. Barry

2006-06-01T23:59:59.000Z

483

Original article: Overview of analytical models of permanent magnet electrical machines for analysis and design purposes  

Science Conference Proceedings (OSTI)

Generally, accurate modelling of electrical machines requires the use of finite-element method. However, FE analysis is too time consuming, especially at firsts design stages, from the point of view of engineers working in R&D departments in the electrical ... Keywords: Analytical modelling, Electromagnetic analysis, Permanent magnet machines

Huguette Tiegna, Yacine Amara, Georges Barakat

2013-04-01T23:59:59.000Z

484

A refinement-based compositional reasoning framework for pipelined machine verification  

Science Conference Proceedings (OSTI)

We present a refinement-based compositional framework for showing that pipelined machines satisfy the same safety and liveness properties as their non-pipelined specifications. Our framework consists of a set of convenient, easily applicable, and complete ... Keywords: compositional reasoning, pipelined machine verification, refinement

Panagiotis Manolios; Sudarshan K. Srinivasan

2008-04-01T23:59:59.000Z

485

Learning to suggest: a machine learning framework for ranking query suggestions  

Science Conference Proceedings (OSTI)

We consider the task of suggesting related queries to users after they issue their initial query to a web search engine. We propose a machine learning approach to learn the probability that a user may find a follow-up query both useful and relevant, ... Keywords: machine learning, query log mining, query suggestion, search assistance

Umut Ozertem; Olivier Chapelle; Pinar Donmez; Emre Velipasaoglu

2012-08-01T23:59:59.000Z

486

Ensemble modeling of transport and dispersion simulations guided by machine learning hypotheses generation  

Science Conference Proceedings (OSTI)

In this article an approach is presented where machine learning classifiers are used to drive an ensemble modeling method of multiple atmospheric transport and dispersion simulations. The goal is to achieve a higher spread of the results with a lower ... Keywords: Ensemble modeling, Machine learning, Transport and dispersion simulations

Andreas D. Lattner; Guido Cervone

2012-11-01T23:59:59.000Z

487

A sequential minimal optimization algorithm for the all-distances support vector machine  

Science Conference Proceedings (OSTI)

The All-Distances SVM is a single-objective light extension of the binary µ-SVM for multi-category classification that is competitive against multi-objective SVMs, such as One-against-the-Rest SVMs and One-against-One SVMs. Although the model takes ... Keywords: kernel machines, multi-category classification, sequential minimal optimization, support vector machines

Diego Candel; Ricardo Ñanculef; Carlos Concha; Héctor Allende

2010-11-01T23:59:59.000Z

488

Intelligent process modeling and optimization of die-sinking electric discharge machining  

Science Conference Proceedings (OSTI)

This paper reports an intelligent approach for process modeling and optimization of electric discharge machining (EDM). Physics based process modeling using finite element method (FEM) has been integrated with the soft computing techniques like artificial ... Keywords: Artificial neural networks (ANN), Electric discharge machining (EDM), Finite element method (FEM), Non-dominated sorting genetic algorithm (NSGA), Process modeling and optimization, Scaled conjugate gradient algorithm (SCG)

S. N. Joshi; S. S. Pande

2011-03-01T23:59:59.000Z

489

New Idea for Hydraulic Testing Machine with Stress and Strain Rates Controlled and its Realization  

Science Conference Proceedings (OSTI)

Based on the relationship between pressure and flux of thin-walled hole, a new idea is proposed for hydraulic testing machine. Using transducer and computer technique, hydraulic system is formed by SCM(single chip micyoco), needle valve, frequency converter ... Keywords: testing machine, stress rate, strain rate, needle valves

Du Jingqing; Gao Shiqiao; Niu Shaohua

2010-05-01T23:59:59.000Z

490

To Design, Build and Test a Wireless Measurement System for Machine Rotor  

Science Conference Proceedings (OSTI)

A wireless measurement system was designed to detect the rotor current of an induction machine. The reason of using wireless technique instead of wire is that it is difficult to connect measured components with wire directly from the rotor which is running ... Keywords: wireless measurement system, machine rotor

Jieyin Zhang; Minxia Zhang

2009-03-01T23:59:59.000Z

491

Simulation of Photovoltaic Array-driven Electric Machines with Power Electronic Interfaces  

Science Conference Proceedings (OSTI)

Power electronic interfaces between photovoltaic (PV) arrays and electric machines are necessary in order to match the drive characteristics with the characteristics of the array for efficient utilization of the resource. This paper proposes a model ... Keywords: MATLAB/SIMULINK modeling, electric machines, photovoltaic array, power electronics, simulation

S. Arul Daniel; N. Ammasai Gounden

2010-11-01T23:59:59.000Z

492

Utilizing cable winding and industrial robots to facilitate the manufacturing of electric machines  

Science Conference Proceedings (OSTI)

Cable wound electric machines are used mainly for high voltage and direct-drive applications. They can be found in areas such as wind power, hydropower, wave power and high-voltage motors. Compared to conventional winding techniques, cable winding includes ... Keywords: Automated production, Electric machine assembly, Industrial robot, Powerformer, Stator winding, Wave energy converter

Erik Hultman; Mats Leijon

2013-02-01T23:59:59.000Z

493

Fuzzy Logic Controller for Enhancement of Transient Stability in Multi Machine AC-DC Power Systems  

Science Conference Proceedings (OSTI)

This paper discusses the impact of HVDC on Power System Stability and proposes a new type of control mechanism based on Fuzzy set theory to augment dynamic performance of a multi-machine power system. To have good damping characteristics over a wide ... Keywords: HVDC, Power System Stability, Multi-Machine Stability, Fuzzy Logic Controller

M. Uma Vani; P. V. Ramana Rao

2010-11-01T23:59:59.000Z

494

TSL: A System for Generating Abstract Interpreters and its Application to Machine-Code Analysis  

Science Conference Proceedings (OSTI)

This article describes the design and implementation of a system, called TSL (for Transformer Specification Language), that provides a systematic solution to the problem of creating retargetable tools for analyzing machine code. TSL ... Keywords: Abstract interpretation, dataflow analysis, dynamic analysis, machine-code analysis, static analysis, symbolic analysis

Junghee Lim; Thomas Reps

2013-04-01T23:59:59.000Z

495

Human-Machine Collaborative Knowledge Modeling in Railway Location Intelligent Environment  

Science Conference Proceedings (OSTI)

To fulfill intelligent railway location", "Human-machine collaboration and modeling railway location knowledge unified is indispensable. Knowledge that man or computer can use are in different representation forms. Furthermore, when man and computer ... Keywords: Railway Location, Human-machine collaboration, Knowledge Representation, Domain-concerned Person Oriented Knowledge, Computer Oriented knowledge

Chunhua Han; Wei Cheng; Xiaofeng Ji; Yuan Xu

2012-04-01T23:59:59.000Z

496

Minimizing total earliness and tardiness on a single machine using a hybrid heuristic  

Science Conference Proceedings (OSTI)

This paper focuses on scheduling jobs with different processing times and distinct due dates on a single machine with no inserted idle time as to minimize the sum of total earliness and tardiness. This scheduling problem is a very important and frequent ... Keywords: Combinatorial optimization, Earliness, Hybrid heuristics, Scheduling, Single machine, Tardiness

Rym M'Hallah

2007-10-01T23:59:59.000Z

497

The Synchronous Boltzmann Machine for learning and hard-combinatoric search  

E-Print Network (OSTI)

The Synchronous Boltzmann Machine for learning and hard-combinatoric search Ursula X. Iturrarán that part of the theory related to energy minimisation only permits one unit at a time to update its state Boltzmann machine is in hard combinatoric search. The main difficulty is that, for a given search problem

Jones, Antonia J.

498

Applying least squares support vector machines to the airframe wing-box structural design cost estimation  

Science Conference Proceedings (OSTI)

This research used the least squares support vector machines (LS-SVM) method to estimate the project design cost of an airframe wing-box structure. We also compared the estimation performance using back-propagation neural networks (BPN) and statistical ... Keywords: Airframe structure, Back-propagation neural networks, Cost estimation, Least squares support vector machines, Response surface methodology

S. Deng; Tsung-Han Yeh

2010-12-01T23:59:59.000Z

499

Energy consumption forecasting in process industry using support vector machines and particle swarm optimization  

Science Conference Proceedings (OSTI)

In this paper, Support Vector Machines (SVMs) are applied in predicting energy consumption in the first phase of oil refining at a particular oil refinery. During cross-validation process of the SVM training Particle Swarm Optimization (PSO) algorithm ... Keywords: energy prediction, particle swarm optimization (PSO), support vector machines (SVM)

Milena R. Petkovi?; Milan R. Rapai?; Boris B. Jakovljevi?

2009-09-01T23:59:59.000Z

500

Energy-Aware Virtual Machine Dynamic Provision and Scheduling for Cloud Computing  

Science Conference Proceedings (OSTI)

Power consumption is one of the most critical problems in data centers. One effective way to reduce power consumption is to consolidate the hosting workloads and shut down physical machines which become idle after consolidation. Server consolidation ... Keywords: Cloud Computing, Data Center, Power Saving, Virtual Machine Consolidation

Ching-Chi Lin; Pangfeng Liu; Jan-Jan Wu

2011-07-01T23:59:59.000Z