Sample records for 202-586-1114 specific technical

  1. Central Solenoid Insert Technical Specification

    SciTech Connect (OSTI)

    Martovetsky, Nicolai N [ORNL; Smirnov, Alexandre [ORNL

    2011-09-01T23:59:59.000Z

    The US ITER Project Office (USIPO) is responsible for the ITER central solenoid (CS) contribution to the ITER project. The Central Solenoid Insert (CSI) project will allow ITER validation the appropriate lengths of the conductors to be used in the full-scale CS coils under relevant conditions. The ITER Program plans to build and test a CSI to verify the performance of the CS conductor. The CSI is a one-layer solenoid with an inner diameter of 1.48 m and a height of 4.45 m between electric terminal ends. The coil weight with the terminals is approximately 820 kg without insulation. The major goal of the CSI is to measure the temperature margin of the CS under the ITER direct current (DC) operating conditions, including determining sensitivity to load cycles. Performance of the joints, ramp rate sensitivity, and stability against thermal or electromagnetic disturbances, electrical insulation, losses, and instrumentation are addressed separately and therefore are not major goals in this project. However, losses and joint performance will be tested during the CSI testing campaign. The USIPO will build the CSI that will be tested at the Central Solenoid Model Coil (CSMC) Test Facility at the Japan Atomic Energy Agency (JAEA), Naka, Japan. The industrial vendors (the Suppliers) will report to the USIPO (the Company). All approvals to proceed will be issued by the Company, which in some cases, as specified in this document, will also require the approval of the ITER Organization. Responsibilities and obligations will be covered by respective contracts between the USIPO, called Company interchangeably, and the industrial Prime Contractors, called Suppliers. Different stages of work may be performed by more than one Prime Contractor, as described in this specification. Technical requirements of the contract between the Company and the Prime Contractor will be covered by the Fabrication Specifications developed by the Prime Contractor based on this document and approved by the Company and ITER. The Fabrication Specifications may reflect some national requirements and regulations that are not fully provided here. This document presents the ITER CSI specifications.

  2. Improvements to Technical Specifications surveillance requirements

    SciTech Connect (OSTI)

    Lobel, R.; Tjader, T.R.

    1992-12-01T23:59:59.000Z

    In August 1983 an NRC task group was formed to investigate problems with surveillance testing required by Technical Specifications, and to recommend approaches to effect improvements. NUREG-1024 ( Technical Specifications-Enhancing Safety Impact'') resulted, and it contained recommendations to review the basis for test frequencies; to ensure that the tests promote safety and do not degrade equipment; and to review surveillance tests so that they do not unnecessarily burden personnel. The Technical Specifications Improvement Program (TSIP) was established in December 1984 to provide the framework for rewriting and improving the Technical Specifications. As an element of the TSIP, all Technical Specifications surveillance requirements were comprehensively examined as recommended in NUREG-1024. The results of that effort are presented in this report. The study found that while some testing at power is essential to verify equipment and system operability, safety can be improved, equipment degradation decreased, and unnecessary personnel burden relaxed by reducing the amount of testing at power.

  3. Technical requirements specification for tank waste retrieval

    SciTech Connect (OSTI)

    Lamberd, D.L.

    1996-09-26T23:59:59.000Z

    This document provides the technical requirements specification for the retrieval of waste from the underground storage tanks at the Hanford Site. All activities covered by this scope are conducted in support of the Tank Waste Remediation System (TWRS) mission.

  4. ALSEP TECHNICAL SPECIFICATION Contract NAS 9-5829

    E-Print Network [OSTI]

    Rathbun, Julie A.

    . ", ., ,I',: , t "' ,- EXHIBIT 13 ALSEP TECHNICAL SPECIFICATION Contract NAS 9-5829 -~ t. ".' . THE MncfYCORPORATION BENDIX SYSTEMS DIVISION' ANN ARBOR MICHIGAN' #12;EXHIBIT B ALSEP TECHNICAL SPECIFICATION Contract NAS 9-5829 March 10, 1966 #12;TABLE OF CONTENTS 1.0 SCOPE 1.1 Scope 1. 2 Associated

  5. Standard technical specifications: Babcock and Wilcox Plants. Revision 1

    SciTech Connect (OSTI)

    NONE

    1995-04-01T23:59:59.000Z

    This report documents the results of the combined effort of the NRC and the industry to produce improved Standard Technical Specifications (STS), Revision 1 for Babcock & Wilcox Plants. The changes reflected in Revision 1 resulted from the experience gained from license amendment applications to convert to these improved STS or to adopt partial improvements to existing technical specifications. This NUREG is the result of extensive public technical meetings and discussions between the Nuclear Regulatory Commission (NRC) staff and various nuclear power plant licensees, Nuclear Steam Supply System (NSSS) Owners Groups, NSSS vendors, and the Nuclear Energy Institute (NEI). The improved STS were developed based on the criteria in the Final Commission Policy Statement on Technical Specifications Improvements for Nuclear Power Reactors, dated July 22, 1993. The improved STS will be used as the basis for individual nuclear power plant licensees to develop improved plant-specific technical specifications. This report contains three volumes. Volume 1 contains the Specifications for all chapters and sections of the improved STS. Volume 2 contains the Bases for Chapters 2.0 and 3.0, and Sections 3.1--3.3 of the improved STS. Volume 3 contains the Bases for Sections 3.4--3.9 of the improved STS.

  6. Technical specifications for mechanical recycling of agricultural plastic waste

    SciTech Connect (OSTI)

    Briassoulis, D., E-mail: briassou@aua.gr; Hiskakis, M.; Babou, E.

    2013-06-15T23:59:59.000Z

    Highlights: • Technical specifications for agricultural plastic wastes (APWs) recycling proposed. • Specifications are the base for best economical and environmental APW valorisation. • Analysis of APW reveals inherent characteristics and constraints of APW streams. • Thorough survey on mechanical recycling processes and industry as it applies to APW. • Specifications for APW recycling tested, adjusted and verified through pilot trials. - Abstract: Technical specifications appropriate for the recycling of agricultural plastic wastes (APWs), widely accepted by the recycling industry were developed. The specifications establish quality standards to be met by the agricultural plastics producers, users and the agricultural plastic waste management chain. They constitute the base for the best economical and environmental valorisation of the APW. The analysis of the APW streams conducted across Europe in the framework of the European project “LabelAgriWaste” revealed the inherent characteristics of the APW streams and the inherent constraints (technical or economical) of the APW. The APW stream properties related to its recycling potential and measured during pilot trials are presented and a subsequent universally accepted simplified and expanded list of APW recycling technical specifications is proposed and justified. The list includes two sets of specifications, applied to two different quality categories of recyclable APW: one for pellet production process (“Quality I”) and another one for plastic profile production process (“Quality II”). Parameters that are taken into consideration in the specifications include the APW physical characteristics, contamination, composition and degradation. The proposed specifications are focused on polyethylene based APW that represents the vast majority of the APW stream. However, the specifications can be adjusted to cover also APW of different materials (e.g. PP or PVC) that are found in very small quantities in protected cultivations in Europe. The adoption of the proposed specifications could transform this waste stream into a labelled commodity traded freely in the market and will constitute the base for the best economical and environmental valorisation of the APW.

  7. Standard technical specifications: Combustion engineering plants. Volume 1, Revision 1: Specifications

    SciTech Connect (OSTI)

    NONE

    1995-04-01T23:59:59.000Z

    This report documents the results of the combined effort of the NRC and the industry to produce improved Standard Technical Specifications (STS), Revision 1 for Combustion Engineering Plants. The changes reflected in Revision 1 resulted from the experience gained from license amendment applications to convert to these improved STS or to adopt partial improvements to existing technical specifications. This NUREG is the result of extensive public technical meetings and discussions between the Nuclear Regulatory Commission (NRC) staff and various nuclear power plant licensees, Nuclear Steam Supply System (NSSS) Owners Groups, NSSS vendors, and the Nuclear Energy Institute (NEI). The improved STS were developed based on the criteria in the Final Commission Policy Statement on Technical Specifications Improvements for Nuclear Power Reactors, dated July 22, 1993. The improved STS will be used as the basis for individual nuclear power plant licensees to develop improved plant-specific technical specifications. This report contains three volumes. Volume 1 contains the Specifications for all chapters and sections of the improved STS. Volume 2 contains the Bases for Chapters 2.0 and 3.0, and Sections 3.1--3.3 of the improved STS. Volume 3 contains the Bases for Sections 3.4--3.9 of the improved STS.

  8. Savannah River Site production reactor technical specifications. K Production Reactor

    SciTech Connect (OSTI)

    NONE

    1996-02-01T23:59:59.000Z

    These technical specifications are explicit restrictions on the operation of the Savannah River Site K Production Reactor. They are designed to preserve the validity of the plant safety analysis by ensuring that the plant is operated within the required conditions bounded by the analysis, and with the operable equipment that is assumed to mitigate the consequences of an accident. Technical specifications preserve the primary success path relied upon to detect and respond to accidents. This report describes requirements on thermal-hydraulic limits; limiting conditions for operation and surveillance for the reactor, power distribution control, instrumentation, process water system, emergency cooling and emergency shutdown systems, confinement systems, plant systems, electrical systems, components handling, and special test exceptions; design features; and administrative controls.

  9. Advanced systems demonstration for utilization of biomass as an energy source. Volume II. Technical specifications

    SciTech Connect (OSTI)

    None

    1980-10-01T23:59:59.000Z

    This volume contains all of the technical specifications relating to materials and construction of the biomass cogeneration facility in the state of Maine. (DMC)

  10. TECHNICAL BASIS FOR VENTILATION REQUIREMENTS IN TANK FARMS OPERATING SPECIFICATIONS DOCUMENTS

    SciTech Connect (OSTI)

    BERGLIN, E J

    2003-06-23T23:59:59.000Z

    This report provides the technical basis for high efficiency particulate air filter (HEPA) for Hanford tank farm ventilation systems (sometimes known as heating, ventilation and air conditioning [HVAC]) to support limits defined in Process Engineering Operating Specification Documents (OSDs). This technical basis included a review of older technical basis and provides clarifications, as necessary, to technical basis limit revisions or justification. This document provides an updated technical basis for tank farm ventilation systems related to Operation Specification Documents (OSDs) for double-shell tanks (DSTs), single-shell tanks (SSTs), double-contained receiver tanks (DCRTs), catch tanks, and various other miscellaneous facilities.

  11. Feasibility assessment of a risk-based approach to technical specifications

    SciTech Connect (OSTI)

    Atefi, B.; Gallagher, D.W. (Science Applications International Corp., McLean, VA (USA))

    1991-05-01T23:59:59.000Z

    To assess the potential use of risk and reliability techniques for improving the effectiveness of the technical specifications to control plant operational risk, the Technical Specifications Branch of the Nuclear Regulatory Commission initiated an effort to identify and evaluate alternative risk-based approaches that could bring greater risk perspective to these requirements. In the first phase four alternative approaches were identified and their characteristics were analyzed. Among these, the risk-based approach to technical specifications is the most promising approach for controlling plant operational risk using technical specifications. The second phase of the study concentrated on detailed characteristics of the real time risk-based approach. It is concluded that a real time risk-based approach to technical specifications has the potential to improve both plant safety and availability. 33 figs., 5 figs., 6 tabs.

  12. Feasibility assessment of a risk-based approach to technical specifications

    SciTech Connect (OSTI)

    Atefi, B.; Gallagher, D.W. (Science Applications International Corp., McLean, VA (USA))

    1991-05-01T23:59:59.000Z

    The first phase of the assessment concentrates on (1) identification of selected risk-based approaches for improving current technical specifications, (2) appraisal of characteristics of each approach, including advantages and disadvantages, and (3) recommendation of one or more approaches that might result in improving current technical specification requirements. The second phase of the work concentrates on assessment of the feasibility of implementation of a pilot program to study detailed characteristics of the preferred approach. The real time risk-based approach was identified as the preferred approach to technical specifications for controlling plant operational risk. There do not appear to be any technical or institutional obstacles to prevent initiation of a pilot program to assess the characteristics and effectiveness of such an approach. 2 tabs.

  13. Technical Specifications

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level:Energy: Grid Integration Redefining What'sis Taking Over Our InstagramStructureProposedPAGESafety Tag:8,, 20153 To.T. J. KulpP.T.

  14. Technical specifications manual for the MARK-1 pulsed ionizing radiation detection system. Volume 1

    SciTech Connect (OSTI)

    Lawrence, R.S.; Harker, Y.D.; Jones, J.L.; Hoggan, J.M.

    1993-03-01T23:59:59.000Z

    The MARK-1 detection system was developed by the Idaho National Engineering Laboratory for the US Department of Energy Office of Arms Control and Nonproliferation. The completely portable system was designed for the detection and analysis of intense photon emissions from pulsed ionizing radiation sources. This manual presents the technical design specifications for the MARK-1 detection system and was written primarily to assist the support or service technician in the service, calibration, and repair of the system. The manual presents the general detection system theory, the MARK-1 component design specifications, the acquisition and control software, the data processing sequence, and the system calibration procedure. A second manual entitled: Volume 2: Operations Manual for the MARK-1 Pulsed Ionizing Radiation Detection System (USDOE Report WINCO-1108, September 1992) provides a general operational description of the MARK-1 detection system. The Operations Manual was written primarily to assist the field operator in system operations and analysis of the data.

  15. Handbook of methods for risk-based analysis of Technical Specification requirements

    SciTech Connect (OSTI)

    Samanta, P.K.; Vesely, W.E.

    1993-12-31T23:59:59.000Z

    Technical Specifications (TS) requirements for nuclear power plants define the Limiting Conditions for Operation (LCOs) and Surveillance Requirements (SRs) to assure safety during operation. In general, these requirements were based on deterministic analysis and engineering judgments. Experiences with plant operation indicate that some elements of the requirements are unnecessarily restrictive, while others may not be conducive to safety. Improvements in these requirements are facilitated by the availability of plant specific Probabilistic Safety Assessments (PSAs). The use of risk and reliability-based methods to improve TS requirements has gained wide interest because these methods can: quantitatively evaluate the risk impact and justify changes based on objective risk arguments. Provide a defensible basis for these requirements for regulatory applications. The United States Nuclear Regulatory Commission (USNRC) Office of Research is sponsoring research to develop systematic risk-based methods to improve various aspects of TS requirements. The handbook of methods, which is being prepared, summarizes such risk-based methods. The scope of the handbook includes reliability and risk-based methods for evaluating allowed outage times (AOTs), action statements requiring shutdown where shutdown risk may be substantial, surveillance test intervals (STIs), defenses against common-cause failures, managing plant configurations, and scheduling maintenances. For each topic, the handbook summarizes methods of analysis and data needs, outlines the insights to be gained, lists additional references, and presents examples of evaluations.

  16. Specification and qualification of welding procedures for metallic materials : Welding procedure test : Part 2: Arc welding of aluminium and its alloys : technical corrigendum 1

    E-Print Network [OSTI]

    International Organization for Standardization. Geneva

    2005-01-01T23:59:59.000Z

    Specification and qualification of welding procedures for metallic materials : Welding procedure test : Part 2: Arc welding of aluminium and its alloys : technical corrigendum 1

  17. Technical specification action requirements for AFW system failures: Method development and application to four PWR plants

    SciTech Connect (OSTI)

    Mankamo, T. [Avaplan Oy, Espoo (Finland); Kim, I.S.; Yang, Ji Wu; Samanta, P.K. [Brookhaven National Lab., Upton, NY (United States)

    1996-09-01T23:59:59.000Z

    Failures in the auxiliary feedwater (AFW) system of pressurized water reactors (PWRs) are considered to involve substantial risk whether a decision is made to either continue power operation while repair is being done, or to shut down the plant to undertake repairs. Technical specification action requirements usually require immediate plant shutdown in the case of multiple failures in the system (in some cases, immediate repair of one train is required when all AFW trains fail). This paper presents a probabilistic risk assessment-based method to quantitatively evaluate and compare both the risks of continued power operation and of shutting the plant down, given known failures in the system. The method is applied to the AFW system for four different PWRs. Results show that the risk of continued power operation and plant shutdown both are substantial, but the latter is larger than the former over the usual repair time. This was proven for four plants with different designs: two operating Westinghouse plants, one operating Asea-Brown Boveri Combustion Engineering Plant, and one of evolutionary design. The method can be used to analyze individual plant design and to improve AFW action requirements using risk-informed evaluations.

  18. Reviewing PSA-based analyses to modify technical specifications at nuclear power plants

    SciTech Connect (OSTI)

    Samanta, P.K.; Martinez-Guridi, G. [Brookhaven National Lab., Upton, NY (United States); Vesely, W.E. [Science Applications International Corporation, Dublin, OH (United States)

    1995-12-01T23:59:59.000Z

    Changes to Technical Specifications (TSs) at nuclear power plants (NPPs) require review and approval by the United States Nuclear Regulatory Commission (USNRC). Currently, many requests for changes to TSs use analyses that are based on a plant`s probabilistic safety assessment (PSA). This report presents an approach to reviewing such PSA-based submittals for changes to TSs. We discuss the basic objectives of reviewing a PSA-based submittal to modify NPP TSs; the methodology of reviewing a TS submittal, and the differing roles of a PSA review, a PSA Computer Code review, and a review of a TS submittal. To illustrate this approach, we discuss our review of changes to allowed outage time (AOT) and surveillance test interval (STI) in the TS for the South Texas Project Nuclear Generating Station. Based on this experience gained, a check-list of items is given for future reviewers; it can be used to verify that the submittal contains sufficient information, and also that the review has addressed the relevant issues. Finally, recommended steps in the review process and the expected findings of each step are discussed.

  19. Handbook of methods for risk-based analyses of technical specifications

    SciTech Connect (OSTI)

    Samanta, P.K.; Kim, I.S. [Brookhaven National Lab., Upton, NY (United States); Mankamo, T. [Avaplan Oy, Espoo (Finland); Vesely, W.E. [Science Applications International Corp., Dublin, OH (United States)

    1994-12-01T23:59:59.000Z

    Technical Specifications (TS) requirements for nuclear power plants define the Limiting Conditions for Operation (LCOs) and Surveillance Requirements (SRs) to assure safety during operation. In general, these requirements are based on deterministic analysis and engineering judgments. Experiences with plant operation indicate that some elements of the requirements are unnecessarily restrictive, while a few may not be conducive to safety. The US Nuclear Regulatory Commission (USNRC) Office of Research has sponsored research to develop systematic risk-based methods to improve various aspects of TS requirements. This handbook summarizes these risk-based methods. The scope of the handbook includes reliability and risk-based methods for evaluating allowed outage times (AOTs), scheduled or preventive maintenance, action statements requiring shutdown where shutdown risk may be substantial, surveillance test intervals (STIs), and management of plant configurations resulting from outages of systems, or components. For each topic, the handbook summarizes analytic methods with data needs, outlines the insights to be gained, lists additional references, and gives examples of evaluations.

  20. CT-guided Bipolar and Multipolar Radiofrequency Ablation (RF Ablation) of Renal Cell Carcinoma: Specific Technical Aspects and Clinical Results

    SciTech Connect (OSTI)

    Sommer, C. M., E-mail: christof.sommer@med.uni-heidelberg.de [University Hospital Heidelberg, INF 110, Department of Diagnostic and Interventional Radiology (Germany); Lemm, G.; Hohenstein, E. [Minimally Invasive Therapies and Nuclear Medicine, SLK Kliniken Heilbronn GmbH, Clinic for Radiology (Germany); Bellemann, N.; Stampfl, U. [University Hospital Heidelberg, INF 110, Department of Diagnostic and Interventional Radiology (Germany); Goezen, A. S.; Rassweiler, J. [Clinic for Urology, SLK Kliniken Heilbronn GmbH (Germany); Kauczor, H. U.; Radeleff, B. A. [University Hospital Heidelberg, INF 110, Department of Diagnostic and Interventional Radiology (Germany); Pereira, P. L. [Minimally Invasive Therapies and Nuclear Medicine, SLK Kliniken Heilbronn GmbH, Clinic for Radiology (Germany)

    2013-06-15T23:59:59.000Z

    Purpose. This study was designed to evaluate the clinical efficacy of CT-guided bipolar and multipolar radiofrequency ablation (RF ablation) of renal cell carcinoma (RCC) and to analyze specific technical aspects between both technologies. Methods. We included 22 consecutive patients (3 women; age 74.2 {+-} 8.6 years) after 28 CT-guided bipolar or multipolar RF ablations of 28 RCCs (diameter 2.5 {+-} 0.8 cm). Procedures were performed with a commercially available RF system (Celon AG Olympus, Berlin, Germany). Technical aspects of RF ablation procedures (ablation mode [bipolar or multipolar], number of applicators and ablation cycles, overall ablation time and deployed energy, and technical success rate) were analyzed. Clinical results (local recurrence-free survival and local tumor control rate, renal function [glomerular filtration rate (GFR)]) and complication rates were evaluated. Results. Bipolar RF ablation was performed in 12 procedures and multipolar RF ablation in 16 procedures (2 applicators in 14 procedures and 3 applicators in 2 procedures). One ablation cycle was performed in 15 procedures and two ablation cycles in 13 procedures. Overall ablation time and deployed energy were 35.0 {+-} 13.6 min and 43.7 {+-} 17.9 kJ. Technical success rate was 100 %. Major and minor complication rates were 4 and 14 %. At an imaging follow-up of 15.2 {+-} 8.8 months, local recurrence-free survival was 14.4 {+-} 8.8 months and local tumor control rate was 93 %. GFR did not deteriorate after RF ablation (50.8 {+-} 16.6 ml/min/1.73 m{sup 2} before RF ablation vs. 47.2 {+-} 11.9 ml/min/1.73 m{sup 2} after RF ablation; not significant). Conclusions. CT-guided bipolar and multipolar RF ablation of RCC has a high rate of clinical success and low complication rates. At short-term follow-up, clinical efficacy is high without deterioration of the renal function.

  1. Technical basis for flawed cylinder test specification to assure adequate fracture resistance of ISO high-strength steel cylinder

    SciTech Connect (OSTI)

    Rana, M.D. [Praxair, Inc., Tonawanda, NY (United States); Smith, J.H. [National Inst. of Standards and Technology, Gaithersburg, MD (United States). Metallurgy Div.; Tribolet, R.O. [Tribolet (R.O.), Van Wert, OH (United States)

    1997-11-01T23:59:59.000Z

    High-pressure industrial gases (such as oxygen, nitrogen, argon, hydrogen, etc.) are stored and transported in portable cylinders. ISO TC58 SC3 has developed a draft specification 9809 for design and fabrication of high-pressure cylinders with maximum tensile strength limitation of 1,100 N/mm{sup 2}. In order to extend the ISO 9809 rules for higher than 1,100 N/mm{sup 2} strength level cylinders, a working group WG14 was formed in 1989 to develop new rules to assure adequate fracture resistance. In 1994, WG14 recommended a simple, but unique flawed cylinder test method for design qualification of the cylinder and acceptance criteria to assure adequate fracture resistance. WG14 also recommended Charpy-V-notch impact tests to control the required fracture resistance on production cylinders. This paper presents the technical basis that was employed in developing the flawed cylinder test method and acceptance criteria. The specification was developed for seamless steel cylinders having actual strength in the range of 1,100 to 1,400 N/mm{sup 2} and cylindrical section wall thickness in the range of 3 to 10 mm. Flawed cylinder tests were conducted on several hundred cylinders of varying sizes and strength levels. The specification requires to demonstrate LEAK-BEFORE-BREAK performance of the cylinder having flaw length equal to 1.6 (o.d. {times} t{sub design}){sup 0.5} at failure pressure = (t{sub design}/t{sub actual}) x Design Pressure.

  2. Technical basis for flawed cylinder test specification to assure adequate fracture resistance of ISO high strength steel cylinder

    SciTech Connect (OSTI)

    Rana, M.D. [Praxair, Inc., Tonawanda, NY (United States). Process and Systems R and D; Smith, J.H. [National Inst. of Standards and Technology, Gaithersburg, MD (United States). Metallurgy Div.; Tribolet, R.O.

    1996-12-01T23:59:59.000Z

    High pressure industrial gases (such as oxygen, nitrogen, argon, hydrogen, etc.) are stored and transported in portable cylinders. ISO TC58 SC3 has developed a draft specification 9809 for design and fabrication of high pressure cylinders with maximum tensile strength limitation of 1,100 N/mm{sup 2}. In order to extend the ISO 9809 rules for higher than 1,100 N/mm{sup 2} strength level cylinders, a working group WG14 was formed in 1989 to develop new rules to assure adequate fracture resistance. In 1994, WG14 recommended a simple, but unique flawed cylinder test method for design qualification of the cylinder and acceptance criteria to assure adequate fracture resistance. WG14 also recommended Charpy-V-Notch impact tests to control the required fracture resistance on production cylinders. This paper presents the technical basis that was employed in developing the flawed cylinder test method and acceptance criteria. The specification was developed for seamless steel cylinders having actual strength in the range of 1,100 to 1,400 N/mm{sup 2} and cylindrical section wall thickness in the range of 3mm to 10mm. Flawed cylinder tests were conducted on several hundred cylinders of varying sizes and strength levels. The specification requires to demonstrate LEAK-BEFORE-BREAK performance of the cylinder having flaw length equal to 1.6(O.D. {times} t{sub design}){sup 0.5} at failure pressure = (t{sub design}/t{sub actual}) {times} Design Pressure.

  3. Technical documentation in support of the project-specific analysis for construction and operation of the National Ignition Facility

    SciTech Connect (OSTI)

    Lazaro, M.A.; Vinikour, W. [Argonne National Lab., IL (United States). Environmental Assessment Div.; Allison, T. [Argonne National Lab., IL (United States). Decision and Information Sciences Div.] [and others

    1996-09-01T23:59:59.000Z

    This document provides information that supports or supplements the data and impact analyses presented in the National Ignition Facility (NIF) Project-Specific Analysis (PSA). The purposes of NIF are to achieve fusion ignition in the laboratory for the first time with inertial confinement fusion (ICF) technology and to conduct high- energy-density experiments ins support of national security and civilian application. NIF is an important element in the DOE`s science-based SSM Program, a key mission of which is to ensure the reliability of the nation`s enduring stockpile of nuclear weapons. NIF would also advance the knowledge of basic and applied high-energy- density science and bring the nation a large step closer to developing fusion energy for civilian use. The NIF PSA includes evaluations of the potential environmental impacts of constructing and operating the facility at one of five candidate site and for two design options.

  4. OSH technical reference manual

    SciTech Connect (OSTI)

    Not Available

    1993-11-01T23:59:59.000Z

    In an evaluation of the Department of Energy (DOE) Occupational Safety and Health programs for government-owned contractor-operated (GOCO) activities, the Department of Labor`s Occupational Safety and Health Administration (OSHA) recommended a technical information exchange program. The intent was to share written safety and health programs, plans, training manuals, and materials within the entire DOE community. The OSH Technical Reference (OTR) helps support the secretary`s response to the OSHA finding by providing a one-stop resource and referral for technical information that relates to safe operations and practice. It also serves as a technical information exchange tool to reference DOE-wide materials pertinent to specific safety topics and, with some modification, as a training aid. The OTR bridges the gap between general safety documents and very specific requirements documents. It is tailored to the DOE community and incorporates DOE field experience.

  5. Technical Guidance

    Broader source: Energy.gov [DOE]

    The Office of Technical Guidance, within the Office of Health, Safety and Security develops and issues Government-wide and Department-wide technical guidance to ensure that classified nuclear...

  6. Mechanical Engineering Department Technical Review

    SciTech Connect (OSTI)

    Carr, R.B.; Denney, R.M. (eds.)

    1981-07-01T23:59:59.000Z

    The Mechanical Engineering Department Technical Review is published to inform readers of various technical activities within the Department, promote exchange of ideas, and give credit to personnel who are achieving the results. The report is presented in two parts: technical achievements and publication abstracts. The first is divided into seven sections, each of which reports on an engineering division and its specific activities related to nuclear tests, nuclear explosives, weapons, energy systems, engineering sciences, magnetic fusion, and materials fabrication.

  7. Technical Assistance to Developers

    SciTech Connect (OSTI)

    Rockward, Tommy [Los Alamos National Laboratory; Borup, Rodney L. [Los Alamos National Laboratory; Garzon, Fernando H. [Los Alamos National Laboratory; Mukundan, Rangachary [Los Alamos National Laboratory; Spernjak, Dusan [Los Alamos National Laboratory

    2012-07-17T23:59:59.000Z

    This task supports the allowance of technical assistance to fuel-cell component and system developers as directed by the DOE. This task includes testing of novel materials and participation in the further development and validation of single cell test protocols. This task also covers technical assistance to DOE Working Groups, the U.S. Council for Automotive Research (USCAR) and the USCAR/DOE Driving Research and Innovation for Vehicle efficiency and Energy sustainability (U.S. Drive) Fuel Cell Technology Team. Assistance includes technical validation of new fuel cell materials and methods, single cell fuel cell testing to support the development of targets and test protocols, and regular advisory participation in other working groups and reviews. This assistance is made available to PEM fuel cell developers by request and DOE Approval. The objectives are to: (1) Support technically, as directed by DOE, fuel cell component and system developers; (2) Assess fuel cell materials and components and give feedback to developers; (3) Assist the DOE Durability Working Group with the development of various new material durability Testing protocols; and (4) Provide support to the U.S. Council for Automotive Research (USCAR) and the USCAR/DOE Fuel Cell Technology Team. FY2012 specific technical objectives are: (1) Evaluate novel MPL materials; (2) Develop of startup/ shutdown protocol; (3) Test the impact of hydrophobic treatment on graphite bi-polar plates; (4) Perform complete diagnostics on metal bi-polar plates for corrosion; and (5) Participate and lead efforts in the DOE Working Groups.

  8. The Technical Specification for the Security Content

    E-Print Network [OSTI]

    ) Karen Scarfone of Scarfone Cybersecurity, and Adam Halbardier of Booz Allen Hamilton wish to thank Farrell, Angela Orebaugh, and Victoria Thompson of Booz Allen Hamilton; Alan Peltzman of the Defense

  9. The Technical Specification for the Security Content

    E-Print Network [OSTI]

    Thompson of Booz Allen Hamilton; Alan Peltzman of the Defense Information Systems Agency (DISA); and Jon

  10. Technical Brief

    E-Print Network [OSTI]

    Depleted Uranium; Brian Littleton

    2006-01-01T23:59:59.000Z

    ii iiiFOREWARD The Depleted Uranium Technical Brief is designed to convey available information and knowledge about depleted uranium to EPA Remedial Project Managers, On-Scene Coordinators, contractors, and other Agency managers involved with the remediation of sites contaminated with this material. It addresses relative questions regarding the chemical and radiological health concerns involved with depleted uranium in the environment. This technical brief was developed to address the common misconception that depleted uranium represents only a radiological health hazard. It provides accepted data and references to additional sources for both the radiological and chemical characteristics, health risk as well as references for both the monitoring and measurement and applicable treatment techniques for depleted uranium. Please Note: This document has been changed from the original publication dated

  11. Technical information

    Annual Energy Outlook 2013 [U.S. Energy Information Administration (EIA)]

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742 33 111 1,613 122 40Coal StocksProvedFeet)ThousandNumber andCrude StreamCrudeTechnical

  12. Technical Sessions

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level:Energy: Grid Integration Redefining What'sis Taking Over Our InstagramStructureProposedPAGESafety Tag:8,, 20153 To synchronizeTechnical

  13. Technical Report Documentation Page 1. Report No.

    E-Print Network [OSTI]

    Texas at Austin, University of

    FINAL COPY Technical Report Documentation Page 1. Report No. FHWA/TX-05/0-1700-2 2. Government-based specifications. 18. Distribution Statement No restrictions. This document is available to the public through

  14. Technical Qualification Program Self-Assessment Report - Los...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    and Federal Technical Capability program was conducted to provide Los Alamos Field Office management specific information related to effectiveness of the documentation and...

  15. Technical Consultant Report Template

    Broader source: Energy.gov [DOE]

    Technical Consultant Report Template, from the Tool Kit Framework: Small Town University Energy Program (STEP).

  16. Biodiesel Progress: ASTM Specifications and 2nd Generation Biodiesel

    Broader source: Energy.gov (indexed) [DOE]

    Progress: ASTM Specifications and 2 nd Generation Biodiesel Steve Howell Technical Director National Biodiesel Board Detroit, Michigan August 15, 2007 Today's Topics Biodiesel...

  17. A Study of Building Information Modeling Usage through the Perceived Utilization of Facilities Management Training, Building Information Modeling Technical Specifications, and a Quality Building Information Model for Facilities Management at Higher Educational Institutions in Texas

    E-Print Network [OSTI]

    Thompson, Darrell

    2014-12-15T23:59:59.000Z

    The research for this study investigated the correlation between the perceived usage of Building Information Modeling in Facilities Management and; the perceived training level of the FM personnel, the perceived specification requirement...

  18. Commissioning Specifications

    Broader source: Energy.gov [DOE]

    Commissioning specifications outline basic requirements of the commissioning process and detail the roles and responsibilities of each party involved. System checklists, startup requirements, and...

  19. Federal Technical Capability Manual

    Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

    2004-05-18T23:59:59.000Z

    Provides requirements and responsibilities to ensure recruitment and hiring of technically capable personnel to retain critical technical capabilities within the Department at all times. Cancels DOE M 426.1-1. Canceled by DOE O 426.1.

  20. Technical Fact Sheets

    Broader source: Energy.gov [DOE]

    Technical Fact Sheets (TFS) provide summary-level information on the impact of new, deployed, applied, and/or planned technical approaches supporting EM cleanup projects.  The TFS is presented as a...

  1. Technical Qualification Program Self-Assessment Report- Los Alamos Field Office- FY15

    Broader source: Energy.gov [DOE]

    The FY15 self-assessment of the Technical Qualifications and Federal Technical Capability program was conducted to provide Los Alamos Field Office (NA-LA) management specific information related to effectiveness of the documentation and implementation of these programs.

  2. Federal Technical Capability

    Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

    2009-11-19T23:59:59.000Z

    This directive defines requirements and responsibilities for meeting the Department of Energy (DOE) commitment to recruiting, deploying, developing, and retaining a technically competent workforce that will accomplish DOE missions in a safe and efficient manner through the Federal Technical Capability Program (FTCP). Cancels DOE M 426.1-1A, Federal Technical Capability Manual.

  3. Technical Standards Program

    Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

    2011-02-23T23:59:59.000Z

    The Order promotes DOE's use of Voluntary Consensus Standards (VCS) as the primary method for application of technical standards and establishes and manages the DOE Technical Standards Program (TSP) including technical standards development, information, activities, issues, and interactions. Admin Chg 1 dated 3-12-13.

  4. Technical Standards Program

    Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

    1999-11-19T23:59:59.000Z

    The Technical Standards Program (TSP) promotes the use of voluntary consensus standards by the Department of Energy (DOE), provides DOE with the means to develop needed technical standards, and manages overall technical standards information, activities, issues, and interactions. Cancels DOE O 1300.2A. Canceled by DOE O 252.1A

  5. Implementation Guide for Use in Developing Technical Safety Requirements

    Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

    2015-03-18T23:59:59.000Z

    This Guide provides a complete description of what Technical Safety Requirements should contain and how they should be developed and maintained. This revision of the guide provides new guidance on Technical Safety Requirements for Specific Administrative Controls, incorporates and addresses lessons learned, and makes clarifications and organization changes to improve usability.

  6. Technical Report Documentation Page 1. Report No.

    E-Print Network [OSTI]

    Texas at Austin, University of

    . Key Words Prestressed Concrete Pavement (PCP), Special Specifications (SS), Nondestructive Testing Development of Post-Tension Prestressed Concrete Pavements in Texas. 16. Abstract This is the third technical of Post-Tensioned Prestressed Concrete Pavements in Texas." The contents of this document intend

  7. Chameleonic Radio Technical Memo No. 4

    E-Print Network [OSTI]

    Ellingson, Steven W.

    Chameleonic Radio Technical Memo No. 4 A Comparison of Some Existing Radios with Implications 1 2 Methodology 1 3 Findings 2 4 Concluding Remarks 3 A Summary of Radio Specifications 5 B.S. consists of a dis- parate collection of radio technologies operating over a wide range of frequencies

  8. NCC Technical Training Opportunity in Concrete

    E-Print Network [OSTI]

    NCC Technical Training Opportunity in Concrete Pavement Technology National Concrete Consortium training through the National Concrete Pavement Technology Center (CP Tech Center). · Michigan Tech for Concrete Pavement: You may select specific subjects within the manual for emphasis if that is of interest

  9. Water Resources Research Center Annual Technical Report

    E-Print Network [OSTI]

    Water Resources Research Center Annual Technical Report FY 1999 Introduction WATER PROBLEMS AND ISSUES OF MISSOURI The water problems and issues in the State of Missouri can be separated into three general areas: 1) water quality, 2) water quantity, and 3) water policy. Each of Missouri's specific

  10. Technical Report Documentation Page 1. Report No.

    E-Print Network [OSTI]

    Texas at Austin, University of

    Technical Report Documentation Page 1. Report No. FHWA/TX-04/4178-2 2. Government Accession No. 3 of Transportation 16. Abstract Changes in the AASHTO Standard Specifications for Structural Supports for Highway commonly used connection details exhibit poor fatigue performance. This study was initiated to confirm

  11. Technical Report Documentation Page 1. Report No.

    E-Print Network [OSTI]

    Texas at Austin, University of

    Technical Report Documentation Page 1. Report No. FHWA/TX-09/0-5444-2 2. Government Accession No. 3. Cross stitching is effective for cracks that are still relatively narrow. Details and specifications are included for a section of US 75 near Sherman that exhibited slab faulting and joint separation. 17. Key

  12. Water Resources Research Institute Annual Technical Report

    E-Print Network [OSTI]

    Water Resources Research Institute Annual Technical Report FY 2003 Introduction The Idaho Water an autonomous statewide source of support for water research and training without regard to specific topic soils contain appreciable amounts of active clay minerals and exhibit shrink-swell behavior in response

  13. Technical Talks Timing

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    a technical talk is to communicate information to the audience. The Speaker Keep in mind that your objective is communication of information. Mumbling, monotone speech and use...

  14. DOE Technical Assistance Program

    Broader source: Energy.gov (indexed) [DOE]

    Designing Effective Residential Retrofit Programs eere.energy.gov The Parker Ranch installation in Hawaii DOE Technical Assistance Program Quality Assurance for Residential...

  15. Exhibit 9RDF Technical Data -ITER UT-B Contracts Div Page 1 of 5

    E-Print Network [OSTI]

    Pennycook, Steve

    Exhibit 9RDF ­ Technical Data - ITER UT-B Contracts Div Sept 2009 Page 1 of 5 ex9rdf-ITER-sept09.doc Exhibit 9RDF-ITER Ref: DEAR 970.5227-1 TECHNICAL DATA ­ ITER (Sept 2009) 1. Rights in Data; (ii) Unlimited rights in Technical Data and Computer Software specifically used in the performa

  16. Exhibit 9RDF Technical Data UT-B Contracts Div Page 1 of 4

    E-Print Network [OSTI]

    Pennycook, Steve

    Exhibit 9RDF ­ Technical Data UT-B Contracts Div Nov 2009 Page 1 of 4 ex9rdf-nov09.doc Exhibit 9RDF) The right to have all technical data and computer software first produced or specifically used Ref: DEAR 970.5227-1 TECHNICAL DATA (Nov 2009) 1. Rights in Data--Facilities. (a) Definitions. (1

  17. Federal Technical Capability

    Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

    2009-11-19T23:59:59.000Z

    To define requirements and responsibilities for meeting the Department of Energy (DOE) commitment to recruiting, deploying, developing, and retaining a technically competent workforce that will accomplish DOE missions in a safe and efficient manner through the Federal Technical Capability Program (FTCP). Chg. 1 dated 9-20-11 Cancels DOE O 426.1. Cancels DOE P 426.1.

  18. About Technical Assistance

    Broader source: Energy.gov [DOE]

    As technologies proceed along the development pipeline, most face major hurdles as they attempt to enter commercial markets. Our Technical Assistance program helps lower a range of institutional barriers to prepare innovative, energy-efficient technologies and energy management systems for full commercial deployment. These projects and activities address barriers that are not technical, Technology Readiness Level 9.

  19. Technical Report Computer Laboratory

    E-Print Network [OSTI]

    Haddadi, Hamed

    the opportunity to consider a physical attack, with very little to lose. We thus set out to analyse the deviceTechnical Report Number 592 Computer Laboratory UCAM-CL-TR-592 ISSN 1476-2986 Unwrapping J. Murdoch Technical reports published by the University of Cambridge Computer Laboratory are freely

  20. Federal Technical Capability Manual

    Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

    2000-06-05T23:59:59.000Z

    The Federal Technical Capability Manual provides the process for the recruitment, deployment, development, and retention of Federal personnel with the demonstrated technical capability to safely accomplish the Departments missions and responsibilities at defense nuclear facilities. Canceled by DOE M 426.1-1A. Does not cancel other directives.

  1. Depleted Uranium Technical Brief

    E-Print Network [OSTI]

    Depleted Uranium Technical Brief United States Environmental Protection Agency Office of Air and Radiation Washington, DC 20460 EPA-402-R-06-011 December 2006 #12;#12;Depleted Uranium Technical Brief EPA of Radiation and Indoor Air Radiation Protection Division ii #12;iii #12;FOREWARD The Depleted Uranium

  2. MATHEMATICAL ENGINEERING TECHNICAL REPORTS

    E-Print Network [OSTI]

    Yamamoto, Hirosuke

    MATHEMATICAL ENGINEERING TECHNICAL REPORTS A Subband Coding Approach to Control under Limited Data Rates and Message Losses Hideaki ISHII and Shinji HARA (Communicated by Kazuo Murota) METR 2006­22 April METR technical reports are published as a means to ensure timely dissemination of scholarly

  3. Soladigm DOE Final Technical Report

    SciTech Connect (OSTI)

    None

    2011-12-31T23:59:59.000Z

    Soladigm's research has produced a fundamental improvement in the technology for dynamic windows by successfully transitioning a low-cost, high-performance dynamic glass fabrication process from a simple 2" research prototype into a full-scale manufacturing environment capable of producing commercial dynamic insulated glass units (IGUs), and developing and optimizing the production process to meet all specifications for mass commercial production. The technology developed under this project is a revolutionary process for fabricating electrochromic glass that today exceeds DOE's 2020 performance and reliability targets at a compelling consumer price point. Before this project, we had demonstrated 2" prototypes using our deposition process that met these performance targets. The goal of this project was to prove that we could transition this lab-scale process to a scalable, "inline" manufacturing process, leveraging existing manufacturing tools capable of achieving a commercially attractive pricepoint in the near-term. Under this project we demonstrated the technical effectiveness of our manufacturing process by achieving or exceeding all of our technical and performance targets for inline fabrication of electrochromic IGUs. These performance specifications exceed DOE's 2020 performance and reliability targets. We also demonstrated the economic feasibility of our manufacturing process by reaching an initial production process that will achieve our target costs, which are compatible with mass adoption.

  4. Security Policy Specification Using a Graphical Approach Page 1 Security Policy Specification Using a Graphical

    E-Print Network [OSTI]

    California at Davis, University of

    Security Policy Specification Using a Graphical Approach Page 1 Security Policy Specification Using of California, Davis {hoagland,pandey,levitt}@cs.ucdavis.edu Technical Report CSE-98-3 A security policy states for organizations to declare their security policies, even informal state- ments would be better than the current

  5. Active Technical Standards Managers List

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    TECHNICAL STANDARDS PROGRAM ASSIGNMENT TELEPHONEFAXEMAIL NAME DOE FACILITYADDRESS LOC CODE AU-30 Jeff D. Feit DOE Technical Standards Program, Manager U.S. Department of Energy...

  6. Final Technical Report

    SciTech Connect (OSTI)

    Joel Walls, Richard Uden, Scott Singleton, Rone Shu, Gary Mavko

    2005-04-12T23:59:59.000Z

    Using current methods, oil and gas in the subsurface cannot be reliably predicted from seismic data. This causes domestic oil and gas fields to go undiscovered and unexploited, thereby increasing the need to import energy. The general objective of this study was to demonstrate a simple and effective methodology for estimating reservoir properties (gas saturation in particular, but also including lithology, net to gross ratios, and porosity) from seismic attenuation and other attributes using P and S-waves. Phase I specific technical objectives: • Develop Empirical or Theoretical Rock Physics Relations for Qp and Qs • Create P-wave and S-wave Synthetic Seismic Modeling Algorithms with Q • Compute P-wave and S-wave Q Attributes from Multi-component Seismic Data All objectives defined in the Phase I proposal were accomplished. During the course of this project, a new class of seismic analysis was developed based on compressional and shear wave inelastic rock properties (attenuation). This method provides a better link between seismic data and the presence of hydrocarbons. The technique employs both P and S-wave data to better discriminate between attenuation due to hydrocarbons versus energy loss due to other factors such as scattering and geometric spreading. It was demonstrated that P and S attenuation can be computed from well log data and used to generate synthetic seismograms. Rock physics models for P and S attenuation were tested on a well from the Gulf of Mexico. The P and S-wave Q attributes were computed on multi-component 2D seismic data intersecting this well. These methods generated reasonable results, and most importantly, the Q attributes indicated gas saturation.

  7. Final Technical Report

    SciTech Connect (OSTI)

    Juan Camilo Serrano

    2011-12-16T23:59:59.000Z

    New and novel material and process technologies applied in wind blade designs and production are critical to increasing the competitiveness of wind power generation against traditional sources of energy. In this project, through collaboration between PPG Industries and MAG Industrial Automation Systems, the potential of using automated manufacturing for the production of fiber glass composite wind blades was evaluated from both technical and economic points of view. Further, it was demonstrated that by modifying the standard blade raw material forms through the use of cost effective pre-impregnated rovings coupled with using an automated fiber placement machine to lay up the parts, it is possible to produce state of the art composite laminates with significantly improved mechanical performance and with higher processing rates than standard blade production technology allows for today, thereby lowering the cost of energy over turbine blades made using traditional processes and materials. In conformity with the scope of work of the submitted proposal, the project team completed each task and documented and reported its findings on the appropriate quarterly report submitted to the DOE project team. The activities and this report are divided into 5 subtasks: (1) Material Investigation - Reviews traditional materials and key specifications and testing methods; (2) Manufacturing and Automation - Identifies new candidate material forms and automated layup processes; (3) Process Development - Performs trials of candidate materials and processes; (4) Predictive Analysis - Assesses impact of new material forms and automated processes on a model blade design; and (5) Feasibility Assessment - Compares traditional manufacturing processes and materials to new candidate material forms and automated processes.

  8. Technical Foundations of the Agent Contest 2008

    E-Print Network [OSTI]

    Zachmann, Gabriel

    (Technical Computer Science) Prof. Dr. Gabriel Zachmann (Computer Graphics) #12;Technical Foundations

  9. Technical Standards, Style Guide- August 1, 2000

    Broader source: Energy.gov [DOE]

    Style Guide for the Preparation of DOE Technical Standards (Standards, Handbooks, and Technical Standards Lists)

  10. How to Design and Market Energy Efficiency Programs to Specific Neighborhoods

    Broader source: Energy.gov [DOE]

    This presentation, given through the DOE's Technical Assitance Program (TAP), identifies how to design and market energy efficiency programs to specific neighborhoods.

  11. Technical Planning Basis

    Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

    2007-07-11T23:59:59.000Z

    The Guide assists DOE/NNSA field elements and operating contractors in identifying and analyzing hazards at facilities and sites to provide the technical planning basis for emergency management programs. Cancels DOE G 151.1-1, Volume 2.

  12. Technical Standards Program

    Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

    2011-02-23T23:59:59.000Z

    The order establishes the DOE Technical Standards Program. Cancels DOE O 252.1 and DOE G 252.1-1. Admin Chg 1, dated 3-12-13 cancels DOE O 252.1A.

  13. DOE Technical Assistance Program

    Broader source: Energy.gov (indexed) [DOE]

    Solid-State Solutions for Municipal Lighting: What You'll Need to Know eere.energy.gov The Parker Ranch installation in Hawaii DOE Technical Assistance Program Solid-State...

  14. Climate Vison: Resources and Links - Technical Information

    Office of Scientific and Technical Information (OSTI)

    Technical Information Publications Case Studies Publications DOE BestPractices Technical Publications The DOE BestPractices team offers a broad selection of technical publications...

  15. Technical Consultant RFP | Department of Energy

    Energy Savers [EERE]

    RFP Technical Consultant RFP Technical Consultant RFP, from the Tool Kit Framework: Small Town University Energy Program (STEP). C3b Technical Consultant RFP.pdf More Documents &...

  16. Technical Report Computer Laboratory

    E-Print Network [OSTI]

    Haddadi, Hamed

    for criminal activity. One general attack route to breach the security is to carry out physical attack afterTechnical Report Number 829 Computer Laboratory UCAM-CL-TR-829 ISSN 1476-2986 Microelectronic report is based on a dissertation submitted January 2009 by the author for the degree of Doctor

  17. MATHEMATICAL ENGINEERING TECHNICAL REPORTS

    E-Print Network [OSTI]

    Yamamoto, Hirosuke

    MATHEMATICAL ENGINEERING TECHNICAL REPORTS Modeling of Contagious Credit Events and Risk Analysis holder. #12;Modeling of Contagious Credit Events and Risk Analysis of Credit Portfolios Suguru YAMANAKA This paper presents a new model of the intensities of contagious credit events such as rating changes

  18. TECHNICAL STANDARDS PROGRAM TOPICAL COMMITTEES

    Broader source: Energy.gov [DOE]

    PurposeThis procedure describes how topical committees are organized and recognized under the Technical Standards Program. 

  19. Business Case for Technical Qualification Program Accreditation...

    Broader source: Energy.gov (indexed) [DOE]

    Business Case for Technical Qualification Program Accreditation Incentives Business Case for Technical Qualification Program Accreditation Incentives TQP Accreditation standardize...

  20. Final Technical Report

    SciTech Connect (OSTI)

    Maxwell, Mike, J., P.E.

    2012-08-30T23:59:59.000Z

    The STI product is the Final Technical Report from ReliOn, Inc. for contract award DE-EE0000487: Recovery Act PEM Fuel Cell Systems Providing Emergency Reserve and Backup Power. The program covered the turnkey deployment of 431 ReliOn fuel cell systems at 189 individual sites for AT&T and PG&E with ReliOn functioning as the primary equipment supplier and the project manager. The Final Technical Report provides an executive level summary, a comparison of the actual accomplishments vs. the goals and objectives of the project, as well as a summary of the project activity from the contract award date of August 1, 2009 through the contract expiration date of December 31, 2011. Two photos are included in the body of the report which show hydrogen storage and bulk hydrogen refueling technologies developed as a result of this program.

  1. 1993 DOE technical standards managers workshop: Proceedings

    SciTech Connect (OSTI)

    Not Available

    1993-12-31T23:59:59.000Z

    This workshop is focused on the benefits of the DOE technical standards program, which is focused toward the preferred use of non-Government standards for DOE activities and the development of DOE technical standards when non-Government standards are not available or are inappropriate. One goal of the program is to replace redundant site-specific standards with more universally accepted documents that have been scrutinized by experts. This replacement is discussed at the workshop along with the problems encountered and solutions found. The workshop provided an opportunity for geographically dispersed people to meet and advance their standards knowledge and efforts to support the program. Safety issues have been the driving force behind the program to date. Several companies offer products and services that support the development, processing, and retrieval of standards. This document mostly comprise vugraphs.

  2. Technical Support Document for Version 3.6.1 of the COMcheck Software

    SciTech Connect (OSTI)

    Bartlett, Rosemarie; Connell, Linda M.; Gowri, Krishnan; Halverson, Mark A.; Lucas, Robert G.; Richman, Eric E.; Schultz, Robert W.; Winiarski, David W.

    2009-09-29T23:59:59.000Z

    This technical support document (TSD) is designed to explain the technical basis for the COMcheck software as originally developed based on the ANSI/ASHRAE/IES Standard 90.1-1989 (Standard 90.1-1989). Documentation for other national model codes and standards and specific state energy codes supported in COMcheck has been added to this report as appendices. These appendices are intended to provide technical documentation for features specific to the supported codes and for any changes made for state-specific codes that differ from the standard features that support compliance with the national model codes and standards.

  3. Honda Transmission Technical Center

    High Performance Buildings Database

    Russells Point, OH The Honda Transmission Technical Center is located on the Honda of America Manufacturing Plant facility site in Russells Point, Ohio. This facility is used for product engineering and market quality testing and analysis of automatic transmissions. The building contains a large workshop area for ten cars, a future dynamometer, two laboratories, an open office area, three conference rooms, a break room, restrooms, and related support areas.

  4. Technical Surveillance Countermeasures Program

    Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

    1993-06-18T23:59:59.000Z

    To prescribe policies, responsibilities and authorities to establish Department of Energy (DOE) Technical Surveillance Countermeasures (TSCM) Program. This order implements the DOE TSCM Procedural Guide, DOE TSCM Operations Manual, DOE TSCM Report Writing Guide and Threat Assessment Scheduling System (TASS) which contain classified policies and procedures concerning the DOE TSCM Program. Cancels DOE 5636.3A. Canceled by DOE O 471.2 dated 9-28-95.

  5. Technical approach document

    SciTech Connect (OSTI)

    Not Available

    1989-12-01T23:59:59.000Z

    The Uranium Mill Tailings Radiation Control Act (UMTRCA) of 1978, Public Law 95-604 (PL95-604), grants the Secretary of Energy the authority and responsibility to perform such actions as are necessary to minimize radiation health hazards and other environmental hazards caused by inactive uranium mill sites. This Technical Approach Document (TAD) describes the general technical approaches and design criteria adopted by the US Department of Energy (DOE) in order to implement remedial action plans (RAPS) and final designs that comply with EPA standards. It does not address the technical approaches necessary for aquifer restoration at processing sites; a guidance document, currently in preparation, will describe aquifer restoration concerns and technical protocols. This document is a second revision to the original document issued in May 1986; the revision has been made in response to changes to the groundwater standards of 40 CFR 192, Subparts A--C, proposed by EPA as draft standards. New sections were added to define the design approaches and designs necessary to comply with the groundwater standards. These new sections are in addition to changes made throughout the document to reflect current procedures, especially in cover design, water resources protection, and alternate site selection; only minor revisions were made to some of the sections. Sections 3.0 is a new section defining the approach taken in the design of disposal cells; Section 4.0 has been revised to include design of vegetated covers; Section 8.0 discusses design approaches necessary for compliance with the groundwater standards; and Section 9.0 is a new section dealing with nonradiological hazardous constituents. 203 refs., 18 figs., 26 tabs.

  6. Heating System Specification Specification of Heating System

    E-Print Network [OSTI]

    Day, Nancy

    Appendix A Heating System Specification /* Specification of Heating System (loosely based */ requestHeat : Room ­? bool; 306 #12; APPENDIX A. HEATING SYSTEM SPECIFICATION 307 /* user inputs */ livingPattern : Room ­? behaviour; setTemp : Room ­? num; heatSwitchOn, heatSwitchOff, userReset : simple

  7. Technical Qualification Program Self-Assessment Report- Carlsbad Field Office- 2012

    Broader source: Energy.gov [DOE]

    Management Assessment (MA-12-08) was conducted from October 1-31, 2012. The management assessment team evaluated the specific requirement implementation, processes, and performance areas of the CBFO Technical Qualification Program (TQP). The assessment covered the relevant parts of DOE 0 426.1, Federal Technical Capability.

  8. GENERAL TECHNICAL REPORT PSW-GTR-245 Management Adaptation to Fires in the

    E-Print Network [OSTI]

    Standiford, Richard B.

    GENERAL TECHNICAL REPORT PSW-GTR-245 357 Management Adaptation to Fires in the Wildland-Urban Risk result in major socio-economic losses and in the worst cases loss of human life. Specifically Institute). #12;GENERAL TECHNICAL REPORT PSW-GTR-245 358 Its configuration has occurred coincidently

  9. Proceedings of IDETC/CIE 2005 ASME 2005 International Design Engineering Technical Conferences

    E-Print Network [OSTI]

    of the system. Rather, such systems exhibit branch- specific nonlinearities which, when collectively analyzedProceedings of IDETC/CIE 2005 ASME 2005 International Design Engineering Technical Conferences Proceedings of IDETC/CIE 2005 ASME 2005 International Design Engineering Technical Conferences & Computers

  10. Final Scientific/Technical Report

    SciTech Connect (OSTI)

    Chang, Yale [JHU/APL; Thomas, Michael E. [JHU/APL; Siegrist, Karen M. [JHU/APL; Lennon, Andrew M. [JHU/APL; Hunter, Lawrence W. [JHU/APL; Oguz, Hasan O. [JHU/APL

    2014-07-01T23:59:59.000Z

    JHU/APL conducted solid propellant fire characterization tests in warm, humid, ambient conditions near sea level. Yttria and ceria surrogate materials were placed in the fires. The substrates simulating ground surfaces were concrete from a Kennedy Space Center launch pad, and steel covered with a protective ablative material representing a launch platform. In-situ instrumentation consisted of witness materials, thermocouples, air handlers, filters, and cascade impactors; remote instrumentation consisted of optical cameras and spectrometers. Test and analysis team members included the Naval Air Warfare Center Aircraft Division, Sandia National Laboratories (SNL), Alliant Techsystems, and the Johns Hopkins University. Test data were analyzed, reported, and delivered, including plume rise and transport captured on video. Derivation of the alumina particle size distributions formed the basis for condensing vapor and agglomeration estimates. Assessment of alumina mass in the plume, along with the surrogate fraction from filter forensics, provided an estimate of airborne surrogate mass. Technical interchange meetings were held with SNL and the Jet Propulsion Laboratory. Specifications for the fire environment were developed and delivered. A thermochemistry model that simultaneously provides the maximum temperature and heat flux was developed and delivered. An SPIE paper on 3D pyrometry of the fire was written and presented.

  11. RADTRAN 6 technical manual.

    SciTech Connect (OSTI)

    Weiner, Ruth F.; Neuhauser, Karen Sieglinde; Heames, Terence John; O'Donnell, Brandon M.; Dennis, Matthew L.

    2014-01-01T23:59:59.000Z

    This Technical Manual contains descriptions of the calculation models and mathematical and numerical methods used in the RADTRAN 6 computer code for transportation risk and consequence assessment. The RADTRAN 6 code combines user-supplied input data with values from an internal library of physical and radiological data to calculate the expected radiological consequences and risks associated with the transportation of radioactive material. Radiological consequences and risks are estimated with numerical models of exposure pathways, receptor populations, package behavior in accidents, and accident severity and probability.

  12. Boiler MACT Technical Assistance

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels DataDepartment of Energy Your Density Isn't Your Destiny: The FutureCommentsEnergyandapproximately 10|BlueFireBoiler MACT Technical

  13. Final Technical Report

    SciTech Connect (OSTI)

    Sobecky, Patricia A; Taillefert, Martial

    2013-03-29T23:59:59.000Z

    This final technical report describes results and findings from a research project to examine the role of microbial phosphohydrolase enzymes in naturally occurring subsurface microorganisms for the purpose of promoting the immobilization of the radionuclide uranium through the production of insoluble uranium phosphate minerals. The research project investigated the microbial mechanisms and the physical and chemical processes promoting uranium biomineralization and sequestration in oxygenated subsurface soils. Uranium biomineralization under aerobic conditions can provide a secondary biobarrier strategy to immobilize radionuclides should the metal precipitates formed by microbial dissimilatory mechanisms remobilize due to a change in redox state.

  14. SPEAR3 | Technical Documentation

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level:Energy: Grid Integration Redefining What's PossibleRadiation Protection245C Unlimited ReleaseWelcome ton n u a l r e p o Technical

  15. Technical Review Panel Report

    Office of Environmental Management (EM)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742 33Frequently AskedEnergyIssuesEnergy Solar Decathlon | DepartmentEnergyOffice -TechnicalTRP

  16. External Technical Review Report

    Office of Environmental Management (EM)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742 33 111 1,613 122Commercial602 1,39732 DOEDepartment of EnergyEric J.ExploringExternal Technical

  17. ARM - Technical Reports

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742EnergyOnItem NotEnergy,ARMForms About Become a UsergovAboutRecoverygovPublicationsTechnical

  18. Mechanical Engineering Department technical abstracts

    SciTech Connect (OSTI)

    Denney, R.M. (ed.)

    1982-07-01T23:59:59.000Z

    The Mechanical Engineering Department publishes listings of technical abstracts twice a year to inform readers of the broad range of technical activities in the Department, and to promote an exchange of ideas. Details of the work covered by an abstract may be obtained by contacting the author(s). Overall information about current activities of each of the Department's seven divisions precedes the technical abstracts.

  19. Mechanical engineering department technical review

    SciTech Connect (OSTI)

    Carr, R.B. Denney, R.M. (eds.)

    1981-01-01T23:59:59.000Z

    The Mechanical Engineering Department Technical Review is published to: (1) inform the readers of various technical activities within the department, (2) promote exchange of ideas, and (3) give credit to the personnel who are achieving the results. The report is formatted into two parts: technical acievements and publication abstracts. The first is divided into eight sections, one for each division in the department providing the reader with the names of the personnel and the division accomplishing the work.

  20. Kansas Water Resources Research Institute Annual Technical Report

    E-Print Network [OSTI]

    Kansas Water Resources Research Institute Annual Technical Report FY 1998 Introduction Research, and bioavailable P losses in runoff are influenced by a variety of factors. The purpose of this project is to quantify the impact of best management practices on P losses in runoff. The specific objectives are: 1

  1. Computer Science and Artificial Intelligence Laboratory Technical Report

    E-Print Network [OSTI]

    Lynch, Nancy

    Computer Science and Artificial Intelligence Laboratory Technical Report massachusetts institute these are translated to executable code. Formal system specifications and their behavior analysis are valuable tools that should be at the disposal of the software developers, especially when dealing with systems exhibiting

  2. TECHNICAL ADVANCE BAR expressolog identification: expression profile similarity

    E-Print Network [OSTI]

    Toronto, University of

    TECHNICAL ADVANCE BAR expressolog identification: expression profile similarity ranking with the highest sequence similarity do not necessarily exhibit the highest expression pattern similarity. Other-annotation or more specific annotation. Ultimately, it is envisaged that this pipeline will aid in improvement

  3. Electrical Engineering and Computer Science Department Technical Report

    E-Print Network [OSTI]

    Shahriar, Selim

    Electrical Engineering and Computer Science Department Technical Report NWU-EECS-09-09 March 25. Current AI systems exhibit brittleness when faced with new situations and domains. This work explores how is extendable by adding additional example-specific models. The robustness of this method for reasoning

  4. Scientific and Technical Information Management

    Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

    2003-10-14T23:59:59.000Z

    The Order establishes requirements and responsibilities for managing DOE's scientific and technical information. Cancels DOE O 241.1. Canceled by DOE O 241.1B.

  5. Technical Services | Argonne National Laboratory

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    noteworthy for their unique technical capabilities: Central Shops facility performs welding and brazing for high-vacuum applications, machining of radioactive materials, and a...

  6. Hydrogen Storage Technical Team Roadmap

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    and technology pathways are impacted by their analyses. These technical teams include Fuel Cells, Fuel Pathway Integration, Hydrogen Delivery, Hydrogen Production, Materials,...

  7. APS Technical Systems Monitoring Page

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Photon Source Technical Systems Accelerator Systems Storage Ring Status for the past 24 hours with real Time of Day User beam delineated. Current, Lifetime, History with 24-hr...

  8. Technical Note LiDAR-derived measures of hurricane-and restoration-generated beach

    E-Print Network [OSTI]

    Weishampel, John F.

    are particularly vulnerable, as they rely on specific beaches for reproduction and exhibit high-nest-site fidelityTechnical Note LiDAR-derived measures of hurricane- and restoration-generated beach morphodynamics

  9. Proceedings of the ASME 2009 International Design Engineering Technical Conferences & Computers and Information in Engineering Conference

    E-Print Network [OSTI]

    Rhoads, Jeffrey F.

    Proceedings of the ASME 2009 International Design Engineering Technical Conferences & Computers bandpass filters based on cyclically-coupled, closed-chain resonator configurations and specifically exhibit improved ripple metrics, reduced frequency dependence Address all correspondence to this author

  10. MILITARY TECHNICAL ACADEMY Vol. XXII, No. 4

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    #12;MILITARY TECHNICAL ACADEMY Vol. XXII, No. 4 © Military Technical Academy Publishing House Technical Academy of Bucharest, Romania Col. Prof. Eng. IOAN NICOLAESCU, Ph.D. The Military Technical Academy of Bucharest, Romania Prof. Eng. VICTOR-VALERIU PATRICIU, Ph.D. The Military Technical Academy

  11. Joint Technical Operations Team | National Nuclear Security Administra...

    National Nuclear Security Administration (NNSA)

    Render Safe Joint Technical Operations Team Joint Technical Operations Team JTOT Logo NNSA's Joint Technical Operations Team (JTOT) provides specialized technical...

  12. Yucca Mountain Site Characterization Project technical data catalog quarterly supplement

    SciTech Connect (OSTI)

    NONE

    1995-03-31T23:59:59.000Z

    The Department of Energy (DOE)/Nuclear Regulatory Commission (NRC) Site-Specific Procedural Agreement for Geologic Repository Site Investigation and Characterization Program requires the DOE to develop and maintain a catalog of data which will be updated and provided to the NRC at least quarterly. This catalog is to include a description of the data; the time (date), place, and method of acquisition; and where the data may be examined. The Yucca Mountain Site Characterization Project (YMP) Technical Data Catalog is published and distributed in accordance with t requirements of the Site-Specific Agreement. The YMP Technical Data Catalog is a report based on reference information contained in the YMP Automated Technical Data Tracking System (ATDT). The reference information is provided by Participants for data acquired or developed in support of the YMP. The Technical Data Catalog is updated quarterly and distributed in the month following the end of each quarter. A complete revision to the catalog is published at the end of each fiscal year. Supplements to the end-of-year edition are published each quarter. These supplements provide information related to new data items not included in previous quarterly updates and data items affected by changes to@ previously published reference information. The Technical Data Catalog, dated September 30, 1994, should be retained as the baseline document for the supplements until the end-of-year revision is published and distributed in October 1995.

  13. Yucca Mountain Site Characterization Project: Technical Data Catalog quarterly supplement

    SciTech Connect (OSTI)

    NONE

    1994-03-31T23:59:59.000Z

    The March 21, 1993, Department of Energy (DOE)/Nuclear Regulatory Commission (NRC) Site-Specific Procedural Agreement for Geologic Repository Site Investigation and Characterization Program requires the DOE to develop and maintain a catalog of data which will be updated and provided to the NRC at least quarterly. This catalog is to include a description of the data; the time (date), place, and method of acquisition; and where it may be examined. The Yucca Mountain Site Characterization Project (YMP) Technical Data Catalog is published and distributed in accordance with the requirements of the Site-Specific Agreement. The YMP Technical Data Catalog is a report based on reference information contained in the YMP Automated Technical Data Tracking System (ATDT). The reference information is provided by Participants for data acquired or developed in support of the YMP. The Technical Data Catalog is updated quarterly and published in the month following the end of each quarter. A complete revision to the Catalog is published at the end of each fiscal year. Supplements to the end-of-year edition are published each quarter. These supplements provide information related to new data items not included in previous quarterly updates and data items affected by changes to previously published reference information. The Technical Data Catalog, dated September 30, 1993, should be retained as the baseline document for the supplements until the end-of-year revision is published and distributed in October 1994.

  14. Final Technical Report: Hydrogen Codes and Standards Outreach

    SciTech Connect (OSTI)

    Hall, Karen I.

    2007-05-12T23:59:59.000Z

    This project contributed significantly to the development of new codes and standards, both domestically and internationally. The NHA collaborated with codes and standards development organizations to identify technical areas of expertise that would be required to produce the codes and standards that industry and DOE felt were required to facilitate commercialization of hydrogen and fuel cell technologies and infrastructure. NHA staff participated directly in technical committees and working groups where issues could be discussed with the appropriate industry groups. In other cases, the NHA recommended specific industry experts to serve on technical committees and working groups where the need for this specific industry expertise would be on-going, and where this approach was likely to contribute to timely completion of the effort. The project also facilitated dialog between codes and standards development organizations, hydrogen and fuel cell experts, the government and national labs, researchers, code officials, industry associations, as well as the public regarding the timeframes for needed codes and standards, industry consensus on technical issues, procedures for implementing changes, and general principles of hydrogen safety. The project facilitated hands-on learning, as participants in several NHA workshops and technical meetings were able to experience hydrogen vehicles, witness hydrogen refueling demonstrations, see metal hydride storage cartridges in operation, and view other hydrogen energy products.

  15. Texas Phosphorus Index TECHNICAL NOTES

    E-Print Network [OSTI]

    Mukhtar, Saqib

    for West Texas, see Figure 1. NRCS and Extension Service specialists in Texas developed the P indicesTexas Phosphorus Index TECHNICAL NOTES U.S. DEPARTMENT OF AGRICULTURE NATURAL RESOURCES CONSERVATION SERVICE TEXAS Revised December, 2012 AGRONOMY TECHNICAL NOTE NUMBER ­ 15 PHOSPHORUS ASSESSMENT

  16. Computer Science Department Technical Report

    E-Print Network [OSTI]

    Shahriar, Selim

    of computing #12;Virtuoso: A System for Virtual Machine Marketplaces Technical Report NWU-CS-04-39 Alex that presents the abstraction of a new raw physical machine on the buyer's network. This report describesComputer Science Department Technical Report NWU-CS-04-39 July 20, 2004 Virtuoso: A System

  17. Technical planning activity: Final report

    SciTech Connect (OSTI)

    Not Available

    1987-01-01T23:59:59.000Z

    In April 1985, the US Department of Energy's (DOE's) Office of Fusion Energy commissioned the Technical Planning Activity (TPA). The purpose of this activity was to develop a technical planning methodology and prepare technical plans in support of the strategic and policy framework of the Magnetic Fusion Program Plan issued by DOE in February 1985. Although this report represents the views of only the US magnetic fusion community, it is international in scope in the sense that the technical plans contained herein describe the full scope of the tasks that are prerequisites for the commercialization of fusion energy. The TPA has developed a well-structured methodology that includes detailed definitions of technical issues, definitions of program areas and elements, statements of research and development objectives, identification of key decision points and milestones, and descriptions of facility requirements.

  18. Technical applications of aerogels

    SciTech Connect (OSTI)

    Hrubesh, L.W.

    1997-08-18T23:59:59.000Z

    Aerogel materials posses such a wide variety of exceptional properties that a striking number of applications have developed for them. Many of the commercial applications of aerogels such as catalysts, thermal insulation, windows, and particle detectors are still under development and new application as have been publicized since the ISA4 Conference in 1994: e.g.; supercapacitors, insulation for heat storage in automobiles, electrodes for capacitive deionization, etc. More applications are evolving as the scientific and engineering community becomes familiar with the unusual and exceptional physical properties of aerogels, there are also scientific and technical application, as well. This paper discusses a variety of applications under development at Lawrence Livermore National Laboratory for which several types of aerogels are formed in custom sizes and shapes. Particular discussions will focus on the uses of aerogels for physics experiments which rely on the exceptional, sometimes unique, properties of aerogels.

  19. FINAL/ SCIENTIFIC TECHNICAL REPORT

    SciTech Connect (OSTI)

    McDonald, Henry; Singh, Suminderpal

    2006-08-28T23:59:59.000Z

    The overall objective of the Chattanooga fuel cell demonstrations project was to develop and demonstrate a prototype 5-kW grid-parallel, solid oxide fuel cell (SOFC) system that co-produces hydrogen, based on Ion America’s technology. The commercial viability of the 5kW SOFC system was tested by transporting, installing and commissioning the SOFC system at the Alternative Energy Laboratory at the University of Tennessee – Chattanooga. The system also demonstrated the efficiency and the reliability of the system running on natural gas. This project successfully contributed to the achievement of DOE technology validation milestones from the Technology Validation section of the Hydrogen, Fuel Cells and Infrastructure Technologies Program Multi-Year Research, Development and Demonstration Plan. Results of the project can be found in the final technical report.

  20. LLNL 1981: technical horizons

    SciTech Connect (OSTI)

    Not Available

    1981-07-01T23:59:59.000Z

    Research programs at LLNL for 1981 are described in broad terms. In his annual State of the Laboratory address, Director Roger Batzel projected a $481 million operating budget for fiscal year 1982, up nearly 13% from last year. In projects for the Department of Energy and the Department of Defense, the Laboratory applies its technical facilities and capabilities to nuclear weapons design and development and other areas of defense research that include inertial confinement fusion, nonnuclear ordnances, and particle-beam technology. LLNL is also applying its unique experience and capabilities to a variety of projects that will help the nation meet its energy needs in an environmentally acceptable manner. A sampling of recent achievements by LLNL support organizations indicates their diversity. (GHT)

  1. Boiler Maximum Achievable Control Technology (MACT) Technical...

    Energy Savers [EERE]

    Boiler Maximum Achievable Control Technology (MACT) Technical Assistance - Fact Sheet, April 2015 Boiler Maximum Achievable Control Technology (MACT) Technical Assistance - Fact...

  2. Building America Residential Energy Efficiency Technical Update...

    Energy Savers [EERE]

    Residential Energy Efficiency Technical Update Meeting: August 2011 Building America Residential Energy Efficiency Technical Update Meeting: August 2011 On this page, you may link...

  3. Low Emission Development Strategies (LEDS): Technical, Institutional...

    Open Energy Info (EERE)

    Strategies (LEDS): Technical, Institutional and Policy Lessons Jump to: navigation, search Tool Summary LAUNCH TOOL Name: Low Emission Development Strategies (LEDS): Technical,...

  4. Independent Oversight Review, Babcock & Wilcox Technical Services...

    Office of Environmental Management (EM)

    Independent Oversight Review, Babcock & Wilcox Technical Services Y-12, LLC - July 2012 Independent Oversight Review, Babcock & Wilcox Technical Services Y-12, LLC - July 2012 July...

  5. Federal Energy Management Program (FEMP) Technical Assistance...

    Energy Savers [EERE]

    Federal Energy Management Program (FEMP) Technical Assistance Request Portal User Guide Federal Energy Management Program (FEMP) Technical Assistance Request Portal User Guide...

  6. Vice President, Engineering and Technical Services

    Broader source: Energy.gov [DOE]

    The Engineering and Technical Services organization is responsible for implementing the transmission capital program, providing technical support for the transmission maintenance program and...

  7. A Technical Databook for Geothermal Energy Utilization

    E-Print Network [OSTI]

    Phillips, S.L.

    1981-01-01T23:59:59.000Z

    A TECHNICAL DATABOOK FOR GEOTHERMAL ENERGY UTILIZATION S.L.Technical Databook for Geothermal Energy Utilization* s. L.Survey, Menlo Park, CA. Geothermal Energy Development, CA.

  8. Space Conditioning Standing Technical Commitee Presentation ...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Commitee Presentation Space Conditioning Standing Technical Commitee Presentation This presentation outlines the goals of the Space Conditioning Standing Technical ommittee, as...

  9. Technical Consultant Report Template | Department of Energy

    Energy Savers [EERE]

    C3d Technical Consultant Report Template.pdf More Documents & Publications External Independent Review (EIR) Report Template Technical Consultant Contract Evaluation Consultant RFP...

  10. Previous Technical Assistance | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    Technical assistance provided to WGAWIEB by the Electricity Market Studies Group of LBNL and The Regulatory Assistance Project (RAP); and More limited technical assistance...

  11. Energy Department Technical Assistance Bolsters Tribal Clean...

    Energy Savers [EERE]

    Technical Assistance Bolsters Tribal Clean Energy Deployment Energy Department Technical Assistance Bolsters Tribal Clean Energy Deployment December 2, 2011 - 3:39pm Addthis The...

  12. Ocean Thermal Extractable Energy Visualization: Final Technical...

    Office of Environmental Management (EM)

    Ocean Thermal Extractable Energy Visualization: Final Technical Report Ocean Thermal Extractable Energy Visualization: Final Technical Report Report about the Ocean Thermal...

  13. Technical Journal The Bendix Technical Journal publishes noteworthy results of

    E-Print Network [OSTI]

    Rathbun, Julie A.

    ADVISORY BOARD E. C. Johnson, Chairman R. E. Esch W. E. Kock L. J. Larsen TECHNICAL CONSULTANTS ALSEP: The Scientific Voice of the Moon L. R. Lewis Some Aspects of ALSEP Structural/Thermal Design J. L

  14. The Independent Technical Analysis Process

    SciTech Connect (OSTI)

    Duberstein, Corey A.; Ham, Kenneth D.; Dauble, Dennis D.; Johnson, Gary E.

    2007-04-13T23:59:59.000Z

    The Bonneville Power Administration (BPA) contracted with the Pacific Northwest National Laboratory (PNNL) to provide technical analytical support for system-wide fish passage information (BPA Project No. 2006-010-00). The goal of this project was to produce rigorous technical analysis products using independent analysts and anonymous peer reviewers. In the past, regional parties have interacted with a single entity, the Fish Passage Center to access the data, analyses, and coordination related to fish passage. This project provided an independent technical source for non-routine fish passage analyses while allowing routine support functions to be performed by other well-qualified entities.

  15. Ideal Based Cyber Security Technical Metrics for Control Systems

    SciTech Connect (OSTI)

    W. F. Boyer; M. A. McQueen

    2007-10-01T23:59:59.000Z

    Much of the world's critical infrastructure is at risk from attack through electronic networks connected to control systems. Security metrics are important because they provide the basis for management decisions that affect the protection of the infrastructure. A cyber security technical metric is the security relevant output from an explicit mathematical model that makes use of objective measurements of a technical object. A specific set of technical security metrics are proposed for use by the operators of control systems. Our proposed metrics are based on seven security ideals associated with seven corresponding abstract dimensions of security. We have defined at least one metric for each of the seven ideals. Each metric is a measure of how nearly the associated ideal has been achieved. These seven ideals provide a useful structure for further metrics development. A case study shows how the proposed metrics can be applied to an operational control system.

  16. 1990 Pacific Northwest Loads and Resources Study, Technical Appendix.

    SciTech Connect (OSTI)

    United States. Bonneville Power Administration.

    1990-12-01T23:59:59.000Z

    The 1990 Pacific Northwest Loads and Resources Study establishes the Bonneville Power Administration's (BPA) planning basis for supplying electricity to BPA customers. The Loads and Resources Study is presented in three documents: (1) this technical appendix detailing loads and resources for each major Pacific Northwest generating utility, (2) a summary of Federal system and Pacific Northwest region loads and resources, and (3) a technical appendix detailing forecasted Pacific Northwest economic trends and loads. This technical appendix provides utility-specific information that BPA uses in its long-range planning. It incorporates the following for each utility: electrical demand--firm loads--under the medium 1990 Draft Joint Load Forecast; generating resources; and contracts both inside and outside the region.

  17. GEM Technical Design Report

    SciTech Connect (OSTI)

    Not Available

    1993-07-31T23:59:59.000Z

    The GEM collaboration was formed in June 1991 to develop a major detector for the SSC. The primary physics objectives of GEM are those central to the motivation for the SSC, to study high p{sub T} physics - exemplified by the search for Higgs bosons - and to search for new physics beyond the standard model. The authors present in this Technical Design Report (TDR) a detector with broad capabilities for the discovery and subsequent study of electroweak symmetry breaking, the origin of mass and flavor, and other physics requiring precise measurements of gammas, electrons, and muons - hence the name, GEM. In addition, as a design goal, they have taken care to provide the robustness needed to do the physics that requires high luminosity. Finally, good coverage and hermeticity allow the detection of missing transverse energy, E{sub T}. The GEM design emphasizes clean identification and high resolution measurement of the primary physics signatures for high p{sub T} physics. The approach is to make precise energy measurements that maximize the sensitivity to rare narrow resonances, to detect the elementary interaction products (quarks, leptons, and photons), and to build in the features required to reduce backgrounds.

  18. Final Technical Report

    SciTech Connect (OSTI)

    Stoessel, Chris

    2013-11-13T23:59:59.000Z

    This project developed a new high-performance R-10/high SHGC window design, reviewed market positioning and evaluated manufacturing solutions required for broad market adoption. The project objectives were accomplished by: identifying viable technical solutions based on modeling of modern and potential coating stacks and IGU designs; development of new coating material sets for HM thin film stacks, as well as improved HM IGU designs to accept multiple layers of HM films; matching promising new coating designs with new HM IGU designs to demonstrate performance gains; and, in cooperation with a window manufacturer, assess the potential for high-volume manufacturing and cost efficiency of a HM-based R-10 window with improved solar heat gain characteristics. A broad view of available materials and design options was applied to achieve the desired improvements. Gated engineering methodologies were employed to guide the development process from concept generation to a window demonstration. The project determined that a slightly de-rated window performance allows formulation of a path to achieve the desired cost reductions to support end consumer adoption.

  19. FINAL TECHNICAL REPORT

    SciTech Connect (OSTI)

    STEFAN VASILE; ZHENG LI

    2010-06-17T23:59:59.000Z

    High-resolution tracking detectors based on Active Pixel Sensor (APS) have been valuable tools in Nuclear Physics and High-Energy Physics research, and have contributed to major discoveries. Their integration time, radiation length and readout rate is a limiting factor for the planed luminosity upgrades in nuclear and high-energy physics collider-based experiments. The goal of this program was to demonstrate and develop high-gain, high-resolution tracking detector arrays with faster readout, and shorter radiation length than APS arrays. These arrays may operate as direct charged particle detectors or as readouts of high resolution scintillating fiber arrays. During this program, we developed in CMOS large, high-resolution pixel sensor arrays with integrated readout, and reset at pixel level. Their intrinsic gain, high immunity to surface and moisture damage, will allow operating these detectors with minimal packaging/passivation requirements and will result in radiation length superior to APS. In Phase I, we designed and fabricated arrays with calorimetric output capable of sub-pixel resolution and sub-microsecond readout rate. The technical effort was dedicated to detector and readout structure development, performance verification, as well as to radiation damage and damage annealing.

  20. Specific Learning Difficulties

    E-Print Network [OSTI]

    Anderson, Jim

    Dyslexia and other Specific Learning Difficulties (SpLDs) A guide for tutors Enabling Services Supporting you to succeed #12;2 Contents Dyslexia Support ............................................................................................................ 3 Recognising students with dyslexia or other specific learning difficulties................. 4

  1. Istanbul Technical University Istanbul, Turkey

    E-Print Network [OSTI]

    Duchowski, Andrew T.

    and ocean engineering Faculty of science and letters Faculty of management Faculty of Aeronautics Engineering Shipbuilding and Ocean Engineering Mathematics Engineering Physics Engineering Chemistry distinguished in Turkey with its engineering and architecture education. Istanbul Technical University

  2. Offshoring and Directed Technical Change

    E-Print Network [OSTI]

    Acemoglu, Daron

    2012-11-24T23:59:59.000Z

    To study the short-run and long-run implications on wage inequality, we introduce directed technical change into a Ricardian model of offshoring. A unique final good is produced by combining a skilled and an unskilled ...

  3. Technical challenges for dismantlement verification

    SciTech Connect (OSTI)

    Olinger, C.T.; Stanbro, W.D.; Johnston, R.G.; Nakhleh, C.W.; Dreicer, J.S.

    1997-11-01T23:59:59.000Z

    In preparation for future nuclear arms reduction treaties, including any potential successor treaties to START I and II, the authors have been examining possible methods for bilateral warhead dismantlement verification. Warhead dismantlement verification raises significant challenges in the political, legal, and technical arenas. This discussion will focus on the technical issues raised by warhead arms controls. Technical complications arise from several sources. These will be discussed under the headings of warhead authentication, chain-of-custody, dismantlement verification, non-nuclear component tracking, component monitoring, and irreversibility. The authors will discuss possible technical options to address these challenges as applied to a generic dismantlement and disposition process, in the process identifying limitations and vulnerabilities. They expect that these considerations will play a large role in any future arms reduction effort and, therefore, should be addressed in a timely fashion.

  4. Facility worker technical basis document

    SciTech Connect (OSTI)

    SHULTZ, M.V.

    2003-08-28T23:59:59.000Z

    This technical basis document was developed to support the Tank Farm Documented Safety Analysis (DSA). It describes the criteria and methodology for allocating controls to hazardous conditions with significant facility work consequence and presents the results of the allocation.

  5. EPA's Financial and Technical Resources

    E-Print Network [OSTI]

    Perea, S. M.

    2011-01-01T23:59:59.000Z

    EPA?s Financial and Technical Resources Suzanna M. Perea, EPA Region VI CATEE Conference November 9, 2011 EPA?s Primary Role Where and how communities are built has a major impact on the environment and on public health. Many programs... are aimed at supporting activities that build more sustainable communities. Protecting Human Health and the Environment Smart Growth Implementation Assistance (SGIA) Grants http://www.epa.gov/smartgrowth/sgia.htm Building Blocks Technical...

  6. Guam Initial Technical Assessment Report

    SciTech Connect (OSTI)

    Baring-Gould, I.; Conrad, M.; Haase, S.; Hotchkiss, E.; McNutt, P.

    2011-04-01T23:59:59.000Z

    Under an interagency agreement, funded by the Department of Interior's (DOI) Office of Insular Affairs (OIA), the National Renewable Energy Laboratory (NREL) was tasked to deliver technical assistance to the island of Guam by conducting an island initial technical assessment that would lay out energy consumption and production data and establish a baseline. This assessment will be used to conduct future analysis and studies by NREL that will estimate energy efficiency and renewable energy potential for the island of Guam.

  7. FAST Final Technical Report

    SciTech Connect (OSTI)

    Toister, Elad

    2014-11-06T23:59:59.000Z

    The FAST project was initiated by BrightSource in an attempt to provide potential solar field EPC contractors with an effective set of tools to perform specific construction tasks. These tasks are mostly associated with heliostat assembly and installation, and require customized non-standard tools. The FAST concept focuses on low equipment cost, reduced setup time and increased assembly throughput as compared to the Ivanpah solar field construction tools.

  8. CTBT technical issues handbook

    SciTech Connect (OSTI)

    Zucca, J.J. [ed.

    1994-05-01T23:59:59.000Z

    The purpose of this handbook is to give the nonspecialist in nuclear explosion physics and nuclear test monitoring an introduction to the topic as it pertains to a Comprehensive Test Ban Treaty (CTBT). The authors have tried to make the handbook visually oriented, with figures paired to short discussions. As such, the handbook may be read straight through or in sections. The handbook covers four main areas and ends with a glossary, which includes both scientific terms and acronyms likely to be encountered during CTBT negotiations. The following topics are covered: (1) Physics of nuclear explosion experiments. This is a description of basic nuclear physics and elementary nuclear weapon design. Also discussed are testing practices. (2) Other nuclear experiments. This section discusses experiments that produce small amounts of nuclear energy but differ from explosion experiments discussed in the first chapter. This includes the type of activities, such as laser fusion, that would continue after a CTBT is in force. (3) Monitoring tests in various environments. This section describes the different physical environments in which a test could be conducted (underground, in the atmosphere, in space, underwater, and in the laboratory); the sources of non-nuclear events (such as earthquakes and mining operations); and the opportunities for evasion. (4) On-site inspections. A CTBT is likely to include these inspections as an element of the verification provisions, in order to resolve the nature of ambiguous events. This chapter describes some technical considerations and technologies that are likely to be useful. (5) Selecting verification measures. This chapter discusses the uncertain nature of the evidence from monitoring systems and how compliance judgments could be made, taking the uncertainties into account. It also discusses how to allocate monitoring resources, given the likelihood of testing by various countries in various environments.

  9. Specific energy for laser removal of rocks.

    SciTech Connect (OSTI)

    Xu, Z.; Kornecki, G.; Reed, C. B.; Gahan, B. C.; Parker, R. A.; Batarseh, S.; Graves, R. M.

    2001-08-16T23:59:59.000Z

    Application of advanced high power laser technology into oil and gas well drilling has been attracting significant research interests recently among research institutes, petroleum industries, and universities. Potential laser or laser-aided oil and gas well drilling has many advantages over the conventional rotary drilling, such as high penetration rate, reduction or elimination of tripping, casing, and bit costs, and enhanced well control, perforating and side-tracking capabilities. The energy required to remove a unit volume of rock, namely the specific energy (SE), is a critical rock property data that can be used to determine both the technical and economic feasibility of laser oil and gas well drilling.

  10. General Technical Report PSW-GTR-243 First Results With a Lab-on-a-Chip System for a

    E-Print Network [OSTI]

    Standiford, Richard B.

    General Technical Report PSW-GTR-243 168 First Results With a Lab-on-a-Chip System for a Fast to a diagnostic lab with specific equipment. This takes time and means financial losses for the commercial nursery and academics collaborated to develop a chip-based technical platform that miniaturized hybridization and PCR

  11. Final Technical Report

    SciTech Connect (OSTI)

    S.T. Misture

    2011-10-29T23:59:59.000Z

    The project was centered on developing new ceramic materials to improve efficiency of solar energy capture for photovoltaic cells and for catalysts to split water to make hydrogen. The work has led to one possible breakthrough material, a nanoscale photocatalyst that can be used to assemble nanocomposite catalysts. Another important result of the work is the development of synthesis methods to create nanostructured and mesoporous oxides for use in solar energy harvesting. Specifically, we have developed two new methods potentially useful for preparing high performance electrodes for PV cells.

  12. Technical Support and Transfer of Geothrmal Technical Knowledge and Information

    SciTech Connect (OSTI)

    John W. Lund

    2007-11-14T23:59:59.000Z

    The Geo-Heat Center (GHC) staff provided responses to 1442 technical support requests during the contract period (April 1, 2006 to September 30, 2007), which were six quarters under this contract. Our website, consisting of 1900 files, also contributes to our technical assistance activity. Downloaded files were 1,889,323 (3,448 per day) from our website, the total number of users was 1,365,258 (2,491 per day), and the total number of hits were 6,008,500 (10,064 per day). The GHC staff attended 60 workshops, short course and professional meeting and made 29 technical presentations. The staff also prepared and mailed out 2,000 copies of each of five issues of the GHC Quaterly Bulletin which contained 26 articles. We also mailed out approximately 5,000 papers and publications to interested individuals and organizations.

  13. Nutrient Management TrainingNutrient Management Training for Technical Service Providersfor Technical Service Providers

    E-Print Network [OSTI]

    Nutrient ManagementNutrient Management ­­ Record KeepingRecord Keeping ­­ Feed ManagementFeed ManagementNutrient Management TrainingNutrient Management Training for Technical Service Providersfor Management Planning Technical Guidance.Management Planning Technical Guidance. Manure and Wastewater Handling

  14. Specific Group Hardware

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Group Hardware Specific Group Hardware ALICE palicevo1 The Virtual Organization (VO) server. Serves as gatekeeper for ALICE jobs. It's duties include getting assignments from...

  15. Legacy Management Specific Training

    Broader source: Energy.gov [DOE]

    The following courses are specific to Legacy Management Employees, for more information about the courses below or to register for any of these courses please contact Chequita Johnson.

  16. CONTENT KNOWLEDGE (Declarative Knowledge; Technical Skills): Students will demonstrate use of critical methods together with mastery of pertinent declarative

    E-Print Network [OSTI]

    Fernandez, Eduardo

    CONTENT KNOWLEDGE (Declarative Knowledge; Technical Skills): Students will demonstrate use effective communication skills by writing thesisdriven essays in response to a specific prompt. Essays are expected to exhibit the control of rhetorical elements that include clarity, coherence, comprehensiveness

  17. FLAMMABLE GAS TECHNICAL BASIS DOCUMENT

    SciTech Connect (OSTI)

    KRIPPS, L.J.

    2005-03-03T23:59:59.000Z

    This document describes the qualitative evaluation of frequency and consequences for DST and SST representative flammable gas accidents and associated hazardous conditions without controls. The evaluation indicated that safety-significant structures, systems and components (SSCs) and/or technical safety requirements (TSRs) were required to prevent or mitigate flammable gas accidents. Discussion on the resulting control decisions is included. This technical basis document was developed to support WP-13033, Tank Farms Documented Safety Analysis (DSA), and describes the risk binning process for the flammable gas representative accidents and associated represented hazardous conditions. The purpose of the risk binning process is to determine the need for safety-significant structures, systems, and components (SSC) and technical safety requirement (TSR)-level controls for a given representative accident or represented hazardous condition based on an evaluation of the event frequency and consequence.

  18. Organic solvent technical basis document

    SciTech Connect (OSTI)

    SANDGREN, K.R.

    2003-03-22T23:59:59.000Z

    This technical basis document was developed to support the Tank Farms Documented Safety Analysis (DSA), and describes the risk binning process and the technical basis for assigning risk bins for the organic solvent fire representative and associated represented hazardous conditions. The purpose of the risk binning process is to determine the need for safety-significant structures, systems, and components (SSC) and technical safety requirement (TSR)-level controls for a given representative accident or represented hazardous conditions based on an evaluation of the frequency and consequence. Note that the risk binning process is not applied to facility workers, because all facility worker hazardous conditions are considered for safety-significant SSCs and/or TSR-level controls. Determination of the need for safety-class SSCs was performed in accordance with DOE-STD-3009-94, Preparation Guide for US Department of Energy Nonreactor Nuclear Facility Documented Safety Analyses, as described in this report.

  19. U.S. Renewable Energy Technical Potentials: A GIS-Based Analysis

    SciTech Connect (OSTI)

    Lopez, A.; Roberts, B.; Heimiller, D.; Blair, N.; Porro, G.

    2012-07-01T23:59:59.000Z

    This report presents the state-level results of a spatial analysis effort calculating energy technical potential, reported in square kilometers of available land, megawatts of capacity, and gigawatt-hours of generation, for six different renewable technologies. For this analysis, the system specific power density (or equivalent), efficiency (capacity factor), and land-use constraints were identified for each technology using independent research, published research, and professional contacts. This report also presents technical potential findings from previous reports.

  20. Exhibit 9ED -Technical Data UT-B Contracts Div Page 1 of 3

    E-Print Network [OSTI]

    Pennycook, Steve

    Exhibit 9ED - Technical Data UT-B Contracts Div June 2011 Page 1 of 3 ex9ed-june11.doc Exhibit 9ED Ref: DEAR 927.409; FAR 52.227-14, 52.227-14 Alt. IV, 52.227-14 Alt. V, 52.227-16 TECHNICAL DATA (June, or statements, regardless of the media in which recorded, that allow or cause a computer to perform a specific

  1. Exhibit 9 Technical Data ITER UT-B Contracts Div Page 1 of 5

    E-Print Network [OSTI]

    Pennycook, Steve

    Exhibit 9 ­ Technical Data ­ ITER UT-B Contracts Div June 2011 Page 1 of 5 ex9-ITER-june11.doc Exhibit 9 ITER Ref: DEAR 927.409; FAR 52.227-14, 52.227-14 Alt.V, 52.227-16 TECHNICAL DATA - ITER (June, or statements, regardless of the media in which recorded, that allow or cause a computer to perform a specific

  2. Exhibit 9 Technical Data UT-B Contracts Div Page 1 of 3

    E-Print Network [OSTI]

    Pennycook, Steve

    Exhibit 9 ­ Technical Data UT-B Contracts Div June 2011 Page 1 of 3 ex9-june11.doc Exhibit 9 Ref: DEAR 927.409; FAR 52.227-14, 52.227-14 Alt.V, 52.227-16 TECHNICAL DATA (June 2011) 1. RIGHTS IN DATA, regardless of the media in which recorded, that allow or cause a computer to perform a specific operation

  3. Spent Nuclear Fuel (SNF) Project Product Specification

    SciTech Connect (OSTI)

    PAJUNEN, A.L.

    2000-12-07T23:59:59.000Z

    The process for removal of Spent Nuclear Fuel (SNF) from the K Basins has been divided into major sub-systems. The Fuel Retrieval System (FRS) removes fuel from the existing storage canisters, cleans it, and places it into baskets. The multi-canister overpack (MCO) loading system places the baskets into an MCO that has been pre-loaded in a cask. The cask, containing a loaded MCO, is then transferred to the Cold Vacuum Drying (CVD) Facility. After drying at the CVD Facility, the cask, and MCO, are transferred to the Canister Storage Building (CSB), where the MCO is removed from the cask, staged, inspected, sealed (by welding), and stored until a suitable permanent disposal option is implemented. The purpose of this document is to specify the process related characteristics of an MCO at the interface between major process systems. The characteristics are derived from the primary technical documents that form the basis for safety analysis and design calculations. This document translates the calculation assumptions into implementation requirements and describes the method of verifying that the requirement is achieved. These requirements are used to define validation test requirements and describe requirements that influence multiple sub-project safety analysis reports. This product specification establishes limits and controls for each significant process parameter at interfaces between major sub-systems that potentially affect the overall safety and/or quality of the SNF packaged for processing, transport, and interim dry storage. The product specifications in this document cover the SNF packaged in MCOs to be transported throughout the SNF Project. The description of the product specifications are organized in the document as follows: Section 2.0--Summary listing of product specifications at each major sub-system interface. Section 3.0--Summary description providing guidance as to how specifications are complied with by equipment design or processing within a major sub-system. Section 4.0--Specific technical basis description for each product specification. The scope of this product specification does not include data collection requirements to support accountability or environmental compliance activities.

  4. FLAMMABLE GAS TECHNICAL BASIS DOCUMENT

    SciTech Connect (OSTI)

    KRIPPS, L.J.

    2003-10-09T23:59:59.000Z

    This technical basis document was developed to support of the Tank Farms Documented Safety Analysis (DSA) and describes the risk binning process for the flammable gas representative accidents and associated represented hazardous conditions. The purpose of the risk binning process is to determine the need for safety-significant structures, systems, and components (SSC) and technical safety requirement (TSR)-level controls for a given representative accident or represented hazardous condition based on an evaluation of the event frequency and consequence. Note that the risk binning process is not applied to facility workers, because all facility worker hazardous conditions are considered for safety-significant SSC and/or TSR-level controls.

  5. Technical Publications | Department of Energy

    Office of Environmental Management (EM)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742 33Frequently AskedEnergyIssuesEnergy Solar Decathlon | Department ofHeating1TechnicalTechnical

  6. US DRIVE Materials Technical Team Roadmap | Department of Energy

    Energy Savers [EERE]

    Materials Technical Team Roadmap US DRIVE Materials Technical Team Roadmap The Materials Technical Team (MTT) focuses primarily on reducing the mass of structural systems such as...

  7. FreedomCAR and Fuel Partnership 2008 Highlights of Technical...

    Energy Savers [EERE]

    8 Highlights of Technical Accomplishments FreedomCAR and Fuel Partnership 2008 Highlights of Technical Accomplishments Report containing brief summaries of key technical...

  8. FreedomCAR and Fuel Partnership 2007 Highlights of Technical...

    Energy Savers [EERE]

    7 Highlights of Technical Accomplishments FreedomCAR and Fuel Partnership 2007 Highlights of Technical Accomplishments Report containing brief summaries of key technical...

  9. FreedomCAR and Fuel Partnership 2009 Highlights of Technical...

    Energy Savers [EERE]

    9 Highlights of Technical Accomplishments FreedomCAR and Fuel Partnership 2009 Highlights of Technical Accomplishments This report summarizes key technical accomplishments achieved...

  10. FreedomCAR and Fuel Partnership 2010 Highlights of Technical...

    Energy Savers [EERE]

    10 Highlights of Technical Accomplishments FreedomCAR and Fuel Partnership 2010 Highlights of Technical Accomplishments This report summarizes key technical accomplishments...

  11. FreedomCAR and Fuel Partnership 2006 Highlights of Technical...

    Energy Savers [EERE]

    6 Highlights of Technical Accomplishments FreedomCAR and Fuel Partnership 2006 Highlights of Technical Accomplishments Report containing brief summaries of key technical...

  12. FreedomCAR and Fuel Partnership 2005 Highlights of Technical...

    Energy Savers [EERE]

    5 Highlights of Technical Accomplishments FreedomCAR and Fuel Partnership 2005 Highlights of Technical Accomplishments Report containing brief summaries of key technical...

  13. Table I: Technical Targets for Catalyst Coated Membranes (CCMs...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    I: Technical Targets for Catalyst Coated Membranes (CCMs): Automotive Table I: Technical Targets for Catalyst Coated Membranes (CCMs): Automotive Technical targets for fuel cell...

  14. Final Technical Report

    SciTech Connect (OSTI)

    Magnuson, Timothy S. [Idaho State University] [Idaho State University

    2013-09-10T23:59:59.000Z

    The biochemistry of bacterial proteins involved in redox transformations of metals and minerals is, without dispute, an important area of research. Nevertheless, most studies on bacterial metal transformation have focused not on biochemistry but on genetics and genomics. The objective of this research is to better understand the role of conformation change in electron transfer from cytochromes to minerals, a process that underpins respiratory metal reduction by bacteria in nature and in bioremediation strategies, including reductive immobilization of radioactive contaminants. Our DOE-funded work is specifically focused on answering long-standing questions about the biochemical behavior of these very interesting proteins, and our findings thus far have already made impacts in the fields of environmental microbiology and biogeochemistry. Among the key findings from the project are 1) Successful large-scale production of biomass for protein isolation; 2) Purification of several c-type cytochromes for biochemical study; 3) Characterization of these proteins using spectrophotometric and electrochemical techniques; 4) Examination of protein conformational change and redox activity towards metal oxides using a small mass cytochrome c from Acidiphilium cryptum; 5) Proteomic characterization of A. cryptum biofilms; 6) Training of 2 undergraduate research assistants; 7) Publications and several meeting presentations.

  15. CEEM Final Technical Report

    SciTech Connect (OSTI)

    Bowers, John

    2014-11-26T23:59:59.000Z

    The mission of the Center for Energy Efficient Materials (CEEM) was to serve the Department of Energy and the nation as a center of excellence dedicated to advancing basic research in nano-structured materials and devices for applications to solar electricity, thermoelectric conversion of waste heat to electricity, and solidstate lighting. The foundation of CEEM was based on the unique capabilities of UCSB and its partner institutions to control, synthesize, characterize, model, and apply materials at the nanoscale for more efficient sustainable energy resources. This unique expertise was a key source of the synergy that unified the research of the Center. Although the Center’s focus was basic research, It’s longer-term objective has been to transfer new materials and devices into the commercial sector where they will have a substantial impact on the nation’s need for efficient sustainable energy resources. As one measure of the impact of the Center, two start-up companies were formed based on its research. In addition, Center participants published a total of 210 archival journal articles, of which 51 were exclusively sponsored by the DOE grant. The work of the Center was structured around four specific tasks: Organic Solar Cells, Solid-State Lighting, Thermoelectrics, and High Efficiency Multi-junction Photovoltaic devices. A brief summary of each follows – detailed descriptions are in Sections 4 & 5 of this report. Research supported through CEEM led to an important shift with respect to the choice of materials used for the fabrication of solution deposited organic solar cells. Solution deposition opens the opportunity to manufacture solar cells via economically-viable high throughput tools, such as roll to roll printing. Prior to CEEM, most organic semiconductors utilized for this purpose involved polymeric materials, which, although they can form thin films reliably, suffer from batch to batch variations due to the statistical nature of the chemical reactions that produce them. In response, the CEEM team developed well-defined molecular semiconductors that produce active layers with very high power conversion efficiencies, in other words they can convert a very high fraction of sunlight into useful electrical power. The fact that the semiconductor is formed from molecular species provides the basis for circumventing the unreliability of polymer counterparts and, as an additional bonus, allows one to attain much grater insight into the structure of the active layer. The latter is particularly important because efficient conversion is the result of a complex arrangement of two semiconductors that need to phase separate in a way akin to oil and water, but with domains that are described by nanoscale dimensions. CEEM was therefore able to provide deep insight into the influence of nanostructure, through the application of structural characterization tools and theoretical methods that describe how electrical charges migrate through the organic layer. Our research in light emitting diode (LED)-based solid state lighting (SSL) was directed at improving efficiency and reducing costs to enable the widespread deployment of economically-viable replacements for inefficient incandescent, halogen, and fluorescent-based lighting. Our specific focus was to advance the fundamental science and technology of light emitting diodes to both understand factors that limit efficiencies and to provide innovative and viable solutions to the current impediments. One of the main challenges we faced is the decrease in efficiency when LEDs are driven harder to increase light output---the so called “droop” effect. It requires large emitting surfaces to reach a desired optical output, and necessitates the use of costly heat sinks, both of which increase the cost. We successfully reduced droop by growing LED crystals having non-conventional orientations. As recognized by the award of the 2014 Nobel prize to the inventors of the nitride LEDs (one of whom was a member of CEEM), LEDs already have a large societal impact in both developed (l

  16. Computer Science Department Technical Report

    E-Print Network [OSTI]

    Shahriar, Selim

    questions on querying and attack-resilience of CDDHT are also discussed. #12;Keywords: security, distributed intrusion detection systems, distributed hash table #12;1 Cyber Disease Monitoring with Distributed HashComputer Science Department Technical Report NWU-CS-04-40 July 12, 2004 Cyber Disease Monitoring

  17. Invite Paper Fall Technical Meeting

    E-Print Network [OSTI]

    Gomez, Alessandro

    within which it is sensible to make predictions, combustion is here to stay. In addition to oil1 Invite Paper Fall Technical Meeting of the Eastern States Section of the Combustion Institute: A Laboratory-Scale Benchmark for Turbulent Combustion Studies Alessandro Gomez Department of Mechanical

  18. Technical Note 499 December1990

    E-Print Network [OSTI]

    Technical Note 499 · December1990 Interpretation as Abduction Jerry R. Hobbs, Mark Stickel;Interpretation as Abduction Jerry R. Hobbs, Mark Stickel, Douglas Appelt, and Paul Martin Artificial Intelligence Center SRI International Abstract Abduction is inference to the best explanation. In the TACITUS project

  19. DOE FINAL TECHNICAL REPORT RP

    SciTech Connect (OSTI)

    RUSS PETERMAN

    2012-01-01T23:59:59.000Z

    The City of Georgetown Utility Systems (GUS) patnered with the private sector, the American Public Power Association (APPA) and Southwestern University to design, construct, test and monitor a solar co-generation system directly connected to the GUS electric distribution system. This report consists of the Primary Technical Report and 3 attachments.

  20. Modularized training for technical editors

    SciTech Connect (OSTI)

    Murphy, P.W.

    1988-09-08T23:59:59.000Z

    This paper outlines the editorial services provided at the Lawrence Livermore National Laboratory (LLNL), sketches a syllabus of basic training for technical editors, describes the approach being used to develop this cost-effective individualized instruction for editors (experienced or not) new to work at LLNL, and enumerates the advantages of this approach. 8 refs.

  1. Defense Technical Information Center thesaurus

    SciTech Connect (OSTI)

    Dickert, J.H. [ed.] [comp.

    1996-10-01T23:59:59.000Z

    This DTIC Thesaurus provides a basic multidisciplinary subject term vocabulary used by DTIC to index and retrieve scientific and technical information from its various data bases and to aid DTIC`s users in their information storage and retrieval operations. It includes an alphabetical posting term display, a hierarchy display, and a Keywork Out of Context (KWOC) display.

  2. Facility worker technical basis document

    SciTech Connect (OSTI)

    EVANS, C.B.

    2003-03-21T23:59:59.000Z

    This report documents the technical basis for facility worker safety to support the Tank Farms Documented Safety Analysis and described the criteria and methodology for allocating controls to hazardous conditions with significant facility worker consequences and presents the results of the allocation.

  3. Mechanical Engineering Department technical review

    SciTech Connect (OSTI)

    Carr, R.B.; Abrahamson, L.; Denney, R.M.; Dubois, B.E (eds.) [eds.

    1982-01-01T23:59:59.000Z

    Technical achievements and publication abstracts related to research in the following Divisions of Lawrence Livermore Laboratory are reported in this biannual review: Nuclear Fuel Engineering; Nuclear Explosives Engineering; Weapons Engineering; Energy Systems Engineering; Engineering Sciences; Magnetic Fusion Engineering; and Material Fabrication. (LCL)

  4. Deleware Water Resources Center Annual Technical Report

    E-Print Network [OSTI]

    of best management practices (BMPs) by private businesses, and improved storm water management & wetlandsDeleware Water Resources Center Annual Technical Report FY 2002 Introduction Delaware Water Resources Center Annual Technical Report Introduction and Program Management/Administration Description FY

  5. Biodiesel ASTM Update and Future Technical Needs

    Broader source: Energy.gov (indexed) [DOE]

    ASTM Update and Future Technical Needs Steve Howell Technical Director National Biodiesel Board ASTM Current Status ASTM D6751 is the approved standard for B100 for blending up to...

  6. Technical Report Documentation Page 1. Report No.

    E-Print Network [OSTI]

    Texas at Austin, University of

    Technical Report Documentation Page 1. Report No. FHWA/TX-00-1795-S 2. Government Accession No. 3. Distribution Statement No restrictions. This document is available to the public through the National Technical

  7. Technical Report Documentation Page 1. Report No.

    E-Print Network [OSTI]

    Texas at Austin, University of

    Technical Report Documentation Page 1. Report No. FHWA/TX-05/0-4485-1 2. Government Accession No. 3 No restrictions. This document is available to the public through the National Technical Information Service

  8. Technical Report Documentation Page 1. Report No.

    E-Print Network [OSTI]

    Texas at Austin, University of

    Technical Report Documentation Page 1. Report No. FHWA/TX-00/0-1843-1 2. Government Accession No. 3 No restrictions. This document is available to the public through the National Technical Information Service

  9. Technical Report Documentation Page 1. Report No.

    E-Print Network [OSTI]

    Texas at Austin, University of

    Technical Report Documentation Page 1. Report No. FHWA/TX-03/4083-2 2. Government Accession No. 3. This document is available to the public through the National Technical Information Service, Springfield

  10. Technical Report Documentation Page 1. Report No.

    E-Print Network [OSTI]

    Zornberg, Jorge G.

    Technical Report Documentation Page 1. Report No. FHWA/TX-12/5-4829-01-3 2. Government Accession No No restrictions. This document is available to the public through the National Technical Information Service

  11. Technical Report Documentation Page 1. Report No.

    E-Print Network [OSTI]

    Texas at Austin, University of

    Technical Report Documentation Page 1. Report No. FHWA/TX-0-1814-1 2. Government Accession No. 3 No restrictions. This document is available to the public through the National Technical Information Service

  12. Technical Report Documentation Page 1. Report No.

    E-Print Network [OSTI]

    Zornberg, Jorge G.

    Technical Report Documentation Page 1. Report No. FHWA/TX-10/0-5812-1 2. Government Accession No. 3. This document is available to the public through the National Technical Information Service, Springfield

  13. Technical Report Documentation Page 1. Report No.

    E-Print Network [OSTI]

    Texas at Austin, University of

    Technical Report Documentation Page 1. Report No. FHWA/TX-03-1838-8 2. Government Accession No. 3. Distribution Statement No restrictions. This document is available to the public through the National Technical

  14. Technical Report Documentation Page 1. Report No.

    E-Print Network [OSTI]

    Texas at Austin, University of

    Technical Report Documentation Page 1. Report No. FHWA/TX-00/1754-1 2. Government Accession No. 3 No restrictions. This document is available to the public through the National Technical Information Service

  15. Technical Report Documentation Page 1. Report No.

    E-Print Network [OSTI]

    Texas at Austin, University of

    Technical Report Documentation Page 1. Report No. FHWA/TX-05/9-580/589-2 2. Government Accession No. Distribution Statement No restrictions. This document is available to the public through the National Technical

  16. Technical Report Documentation Page 1. Report No.

    E-Print Network [OSTI]

    Texas at Austin, University of

    Technical Report Documentation Page 1. Report No. FHWA/TX-04/1778-4 2. Government Accession No. 3 No restrictions. This document is available to the public through the National Technical Information Service

  17. Technical Report Documentation Page 1. Report No.

    E-Print Network [OSTI]

    Texas at Austin, University of

    Technical Report Documentation Page 1. Report No. FHWA/TX-04/0-1734-S 2. Government Accession No. 3 No restrictions. This document is available to the public through the National Technical Information Service

  18. Technical Report Documentation Page 1. Report No.

    E-Print Network [OSTI]

    Texas at Austin, University of

    Technical Report Documentation Page 1. Report No. FHWA/TX-11/0-6348-1 2. Government Accession No. 3. Distribution Statement No restrictions. This document is available to the public through the National Technical

  19. Technical Report Documentation Page 1. Report No.

    E-Print Network [OSTI]

    Texas at Austin, University of

    Technical Report Documentation Page 1. Report No. FHWA/TX-00/1785-2 2. Government Accession No. 3 No restrictions. This document is available to the public through the National Technical Information Service

  20. Technical Report Documentation Page 1. Report No.

    E-Print Network [OSTI]

    Texas at Austin, University of

    Technical Report Documentation Page 1. Report No. FHWA/TX-03/4386-1 2. Government Accession No. 3. Distribution Statement No restrictions. This document is available to the public through the National Technical

  1. Technical Report Documentation Page 1. Report No.

    E-Print Network [OSTI]

    Texas at Austin, University of

    Technical Report Documentation Page 1. Report No. FHWA/TX-06/0-4085-5 2. Government Accession No. 3. Distribution Statement No restrictions. This document is available to the public through the National Technical

  2. Technical Report Documentation Page 1. Report No.

    E-Print Network [OSTI]

    Texas at Austin, University of

    Technical Report Documentation Page 1. Report No. FHWA/TX-06/0-1401-2 2. Government Accession No. 3. Distribution Statement No restrictions. This document is available to the public through the National Technical

  3. Technical Report Documentation Page 1. Report No.

    E-Print Network [OSTI]

    Texas at Austin, University of

    Technical Report Documentation Page 1. Report No. FHWA/TX-10/0-5974-1 2. Government Accession No. 3. Distribution Statement No restrictions. This document is available to the public through the National Technical

  4. Technical Report Documentation Page 1. Report No.

    E-Print Network [OSTI]

    Texas at Austin, University of

    Technical Report Documentation Page 1. Report No. FHWA/TX-04/0-1471-4 2. Government Accession No. 3. Distribution Statement No restrictions. This document is available to the public through the National Technical

  5. Technical Report Documentation Page 1. Report No.

    E-Print Network [OSTI]

    Texas at Austin, University of

    Technical Report Documentation Page 1. Report No. FHWA/TX-0-1748-2 2. Government Accession No. 3. This document is available to the public through the National Technical Information Service, Springfield

  6. Technical Report Documentation Page 1. Report No.

    E-Print Network [OSTI]

    Texas at Austin, University of

    Technical Report Documentation Page 1. Report No. FHWA/TX-04/0-4808-1 2. Government Accession No. 3. This document is available to the public through the National Technical Information Service, Springfield

  7. Technical Report Documentation Page 1. Report No.

    E-Print Network [OSTI]

    Texas at Austin, University of

    Technical Report Documentation Page 1. Report No. FHWA/TX-04/5-3933-01-P1-4 2. Government Accession No restrictions. This document is available to the public through the National Technical Information Service

  8. Technical Report Documentation Page 1. Report No.

    E-Print Network [OSTI]

    Texas at Austin, University of

    Technical Report Documentation Page 1. Report No. FHWA/TX-06/0-4437-1 2. Government Accession No. 3. This document is available to the public through the National Technical Information Service, Springfield

  9. Technical Report Documentation Page 1. Report No.

    E-Print Network [OSTI]

    Texas at Austin, University of

    Technical Report Documentation Page 1. Report No. FHWA/TX-06/5-4975-01-1 2. Government Accession No. This document is available to the public through the National Technical Information Service, Springfield

  10. Technical Report Documentation Page 1. Report No.

    E-Print Network [OSTI]

    Texas at Austin, University of

    Technical Report Documentation Page 1. Report No. FHWA/TX-06/0-4185-4 2. Government Accession No. 3. This document is available to the public through the National Technical Information Service, Springfield

  11. Technical Report Documentation Page 1. Report No.

    E-Print Network [OSTI]

    Texas at Austin, University of

    Technical Report Documentation Page 1. Report No. FHWA/TX-06/0-4958-1 2. Government Accession No. 3 No restrictions. This document is available to the public through the National Technical Information Service

  12. Technical Report Documentation Page 1. Report No.

    E-Print Network [OSTI]

    Texas at Austin, University of

    Technical Report Documentation Page 1. Report No. FHWA/TX-11/0-6095-2 2. Government Accession No. 3 Statement No restrictions. This document is available to the public through the National Technical

  13. Technical Report Documentation Page 1. Report No.

    E-Print Network [OSTI]

    Texas at Austin, University of

    Technical Report Documentation Page 1. Report No. FHWA/TX-07/0-1700-7 2. Government Accession No. 3. Distribution Statement No restrictions. This document is available to the public through the National Technical

  14. Technical Report Documentation Page 1. Report No.

    E-Print Network [OSTI]

    Texas at Austin, University of

    Technical Report Documentation Page 1. Report No. FHWA/TX-07/0-5410-1 2. Government Accession No. 3 No restrictions. This document is available to the public through the National Technical Information Service

  15. Technical Report Documentation Page 1. Report No.

    E-Print Network [OSTI]

    Texas at Austin, University of

    Technical Report Documentation Page 1. Report No. FHWA/TX-05/0-4661-1 2. Government Accession No. 3. This document is available to the public through the National Technical Information Service, Springfield

  16. Technical Report Documentation Page 1. Report No.

    E-Print Network [OSTI]

    Texas at Austin, University of

    Technical Report Documentation Page 1. Report No. FHWA/TX-04/0-1700-1 2. Government Accession No. 3. Distribution Statement No restrictions. This document is available to the public through the National Technical

  17. PRELIMINARY REVIEW COPY Technical Report Documentation Page

    E-Print Network [OSTI]

    Zornberg, Jorge G.

    PRELIMINARY REVIEW COPY Technical Report Documentation Page 1. Report No. FHWA/TX-13/0-6603-2 2 No restrictions. This document is available to the public through the National Technical Information Service

  18. Technical Report Documentation Page 1. Report No.

    E-Print Network [OSTI]

    Texas at Austin, University of

    Technical Report Documentation Page 1. Report No. FHWA/TX-04/4576-3 2. Government Accession No. 3 Statement No restrictions. This document is available to the public through the National Technical

  19. Technical Report Documentation Page 1. Report No.

    E-Print Network [OSTI]

    Texas at Austin, University of

    Technical Report Documentation Page 1. Report No. FHWA/TX-09/0-5799-1 2. Government Accession No. 3 Statement No restrictions. This document is available to the public through the National Technical

  20. Technical Report Documentation Page 1. Report No.

    E-Print Network [OSTI]

    Texas at Austin, University of

    Technical Report Documentation Page 1. Report No. FHWA/TX-7-4957-1 2. Government Accession No. 3 No restrictions. This document is available to the public through the National Technical Information Service

  1. Technical Report Documentation Page 1. Report No.

    E-Print Network [OSTI]

    Texas at Austin, University of

    Technical Report Documentation Page 1. Report No. FHWA/TX-05/0-4416-1 2. Government Accession No. 3 No restrictions. This document is available to the public through the National Technical Information Service

  2. Technical Report Documentation Page 1. Report No.

    E-Print Network [OSTI]

    Texas at Austin, University of

    Technical Report Documentation Page 1. Report No. FHWA/TX-07/0-1895-1 2. Government Accession No. 3. Distribution Statement No restrictions. This document is available to the public through the National Technical

  3. Technical Report Documentation Page 1. Report No.

    E-Print Network [OSTI]

    Texas at Austin, University of

    Technical Report Documentation Page 1. Report No. FHWA/TX-0-2129-1 2. Government Accession No. 3. Distribution Statement No restrictions. This document is available to the public through the National Technical

  4. Technical Report Documentation Page 1. Report No.

    E-Print Network [OSTI]

    Texas at Austin, University of

    Technical Report Documentation Page 1. Report No. FHWA/TX-07/0-5068-2 2. Government Accession No. 3 No restrictions. This document is available to the public through the National Technical Information Service

  5. Technical Report Documentation Page 1. Report No.

    E-Print Network [OSTI]

    Texas at Austin, University of

    Technical Report Documentation Page 1. Report No. FHWA/TX-05/0-4410-2 2. Government Accession No. 3. Distribution Statement No restrictions. This document is available to the public through the National Technical

  6. Technical Report Documentation Page 1. Report No.

    E-Print Network [OSTI]

    Texas at Austin, University of

    Technical Report Documentation Page 1. Report No. FHWA/TX-09/0-5830-1 2. Government Accession No. 3 No restrictions. This document is available to the public through the National Technical Information Service

  7. Technical Report Documentation Page 1. Report No.

    E-Print Network [OSTI]

    Texas at Austin, University of

    Technical Report Documentation Page 1. Report No. FHWA/TX-05/0-4069-1 2. Government Accession No. 3. This document is available to the public through the National Technical Information Service, Springfield

  8. Technical Report Documentation Page 1. Report No.

    E-Print Network [OSTI]

    Texas at Austin, University of

    Technical Report Documentation Page 1. Report No. 9-572-1 2. Government Accession No. 3. Recipient Statement No restrictions. This document is available to the public through the National Technical

  9. Technical Report Documentation Page 1. Report No.

    E-Print Network [OSTI]

    Texas at Austin, University of

    Technical Report Documentation Page 1. Report No. FHWA/TX-06/0-4661-2 2. Government Accession No. 3. Distribution Statement No restrictions. This document is available to the public through the National Technical

  10. Technical Report Documentation Page 1. Report No.

    E-Print Network [OSTI]

    Texas at Austin, University of

    Technical Report Documentation Page 1. Report No. FHWA/TX-05/0-1713-1 2. Government Accession No. 3 No restrictions. This document is available to the public through the National Technical Information Service

  11. Technical Report Documentation Page 1. Report No.

    E-Print Network [OSTI]

    Zornberg, Jorge G.

    Technical Report Documentation Page 1. Report No. FHWA/TX-07/0-5202-2 2. Government Accession No. 3 No restrictions. This document is available to the public through the National Technical Information Service

  12. Technical Report Documentation Page 1. Report No.

    E-Print Network [OSTI]

    Texas at Austin, University of

    Technical Report Documentation Page 1. Report No. FHWA/TX-05/0-4185-3 2. Government Accession No. 3 Statement No restrictions. This document is available to the public through the National Technical

  13. Technical Report Documentation Page 1. Report No.

    E-Print Network [OSTI]

    Texas at Austin, University of

    Technical Report Documentation Page 1. Report No. FHWA/TX-10/0-5973-2 2. Government Accession No. 3. Distribution Statement No restrictions. This document is available to the public through the National Technical

  14. Technical Report Documentation Page 1. Report No.

    E-Print Network [OSTI]

    Zornberg, Jorge G.

    Technical Report Documentation Page 1. Report No. FHWA/TX-13/5-4829-01-2 2. Government Accession No. This document is available to the public through the National Technical Information Service, Springfield

  15. Technical Report Documentation Page 1. Report No.

    E-Print Network [OSTI]

    Texas at Austin, University of

    Technical Report Documentation Page 1. Report No. FHWA/TX-05/0-1713-2 2. Government Accession No. 3. Distribution Statement No restrictions. This document is available to the public through the National Technical

  16. Technical Report Documentation Page 1. Report No.

    E-Print Network [OSTI]

    Texas at Austin, University of

    Technical Report Documentation Page 1. Report No. FHWA/TX-07/0-5176-2 2. Government Accession No. 3. Distribution Statement No restrictions. This document is available to the public through the National Technical

  17. Technical Report Documentation Page 1. Report No.

    E-Print Network [OSTI]

    Texas at Austin, University of

    Technical Report Documentation Page 1. Report No. FHWA/TX-05/5-1924-01-1 2. Government Accession No No restrictions. This document is available to the public through the National Technical Information Service

  18. Technical Report Documentation Page 1. Report No.

    E-Print Network [OSTI]

    Texas at Austin, University of

    Technical Report Documentation Page 1. Report No. FHWA/TX-09/0-5668-1 2. Government Accession No. 3. Distribution Statement No restrictions. This document is available to the public through the National Technical

  19. Specific light in sculpture

    E-Print Network [OSTI]

    Powell, John William

    1989-01-01T23:59:59.000Z

    Specific light is defined as light from artificial or altered natural sources. The use and manipulation of light in three dimensional sculptural work is discussed in an historic and contemporary context. The author's work ...

  20. Redesigning specificity in miniproteins

    E-Print Network [OSTI]

    Taylor, Christina Marie

    2006-01-01T23:59:59.000Z

    This work focuses on designing specific miniprotein interactions using computational models and then testing these designs with experiments. Miniproteins are small, autonomously-folding proteins that are excellent for ...

  1. Extraction Utility Design Specification

    Energy Savers [EERE]

    Extraction Utility Design Specification January 11, 2011 Document Version 1.9 1 Revision History Date Version Section and Titles Author Summary of Change January 15, 2010 1.0 All...

  2. Space Conditioning Standing Technical Committee Strategic Plan

    Broader source: Energy.gov [DOE]

    This strategic plan document outlines the gaps, barriers, and opportunities identified by the Building America Space Conditioning Standing Technical Committee.

  3. Supporting Technical Documents | Department of Energy

    Office of Environmental Management (EM)

    Environmental Department (NMED) Los Alamos National Laboratory (LANL) Hazardous Waste Facility Permit Supporting Technical Document for the Radiological Release Accident...

  4. Harmonization of Biodiesel Specifications

    SciTech Connect (OSTI)

    Alleman, T. L.

    2008-02-01T23:59:59.000Z

    Worldwide biodiesel production has grown dramatically over the last several years. Biodiesel standards vary across countries and regions, and there is a call for harmonization. For harmonization to become a reality, standards have to be adapted to cover all feedstocks. Additionally, all feedstocks cannot meet all specifications, so harmonization will require standards to either tighten or relax. For harmonization to succeed, the biodiesel market must be expanded with the alignment of test methods and specification limits, not contracted.

  5. Final Technical Report

    SciTech Connect (OSTI)

    Efthimios Kaxiras

    2009-02-02T23:59:59.000Z

    This research consisted of a theoretical investigation of the properties of surface-based nanostructures, having as a main goal the deeper understanding of the atomic-scale mechanisms responsible for the formation and stability of such structures. This understanding will lead to the design of improved systems for applications in diverse areas such as novel electronic devices, sensors, field-effect transistors, substrates with enhanced hydro-phobic (water repelling) or hydro-philic (water absorbing) behavior for coatings of various surfaces used in bioengineering, flexible displays, organic photovoltaics, etc. The research consisted of developing new theoretical methodologies and applying them to a wide range of interesting physical systems. Highlights of the new methodologies include techniques for bridging different scales, from the quantum-mechanical electronic level to the meso-scopic level of large molecular structures such as DNA, carbon nanotubes and two-dimensional assemblies of organic molecules. These methodologies were successfully applied to investigate interactions between systems that are large on the atomic scale (reaching the scale of microns in length or milliseconds in time), but still incorporating all the essential elements of the atomic-scale structure. While the research performed here did not address applications directly, the implications of its finding are important in guiding experimental searches and in coming up with novel solutions to important problems. In this sense, the results of this work can be incorporated in the design of many useful applications. Specifically, in addition to elucidating important physical principles on how nano-structures are stabilized on surfaces, we have used our theoretical investigations to make predictions for useful applications in the following fields: a) we proposed new types of nanotubes that can overcome the limitations of the carbon nanotubes whose properties depend sensitively on the structure which cannot be controlled experimentally; b) we showed how carbon nanotubes can be employed in optical determination of the DNA base sequence, an exciting application for ultra-fast DNA sequencing; c) we proposed a nano-structure (titanium dioxide nano-wire) based design for organic photovoltaics using natural dyes, and showed that it will be an efficient system for the absorption of light and the charge transfer from the dye to the wire.

  6. Final Technical Report

    SciTech Connect (OSTI)

    Helen Cunning

    2012-05-08T23:59:59.000Z

    Hackensack University Medical Center's major initiative to create a cleaner healthier and safer environment for patients, employees and the community served by the medical center is built on its commitment to protect the environment and conserve precious energy resources. Since 2004 the Medical Center launched a long term campaign to temper the negative environmental impact of proposed and existing new construction at the medical center and to improve campus wide overall energy efficiency. The plan was to begin by implementing a number of innovative and eco-friendly enhancements to the Gabrellian Women's and Children's Pavilion, in construction at the time, which would lead to Certification by the US Green Building Councils Leadership & Environmental Design (LEED) program. In addition the medical center would evaluate the feasibility of implementing a photovoltaic system in the new construction (in development and planned) to provide clean pollution free electricity. The steps taken to achieve this included conducting a feasibility study complete with architectural and engineering assessments to determine the potential for implementation of a photovoltaic system on the campus and also to conduct an energy survey that would focus on determining specific opportunities and upgrades that would lead to a healthier energy efficient interior environment at the medical center. The studies conducted by the medical center to determine the viability of installing a photovoltaic system identified two key issues that factored into leaderships decision not to implement the solar powered system. These factors were related to the advanced phase of construction of the women's and children's pavilion and the financial considerations to redesign and implement in the ambulatory cancer center. The medical center, in spite of their inability to proceed with the solar aspect of the project upheld their commitment to create a healthier environment for the patients and the community. To achieve a healthier energy efficient interior environment the medical center made substantive upgrades and improvements to the HVAC, plumbing electrical and other operating systems. Measures that were implemented range from use of lighting and plumbing fixture sensors , to reduce electrical and water usage, to use of refrigerants containing hydrochlorofluorocarbons (HCFCs) which cause significantly less depletion of the ozone layer than the refrigerants more commonly used. Additional appropriate energy efficiency component upgrades include the installation of Chiller plants with variable frequency drives (VFDs) and harmonic filters, high efficiency motors, solar window glazing, and lighting/motion sensors.

  7. UNITED STATES NUCLEAR WASTE TECHNICAL REVIEW BOARD

    E-Print Network [OSTI]

    UNITED STATES NUCLEAR WASTE TECHNICAL REVIEW BOARD 2300 Clarendon Boulevard, Suite 1300 Arlington are pleased to transmit a technical report prepared by the Nuclear Waste Technical Review Board (Board. Based on its review of data gathered by the DOE and the Center for Nuclear Waste Regulatory Analyses

  8. Effective Community-Wide Policy Technical Assistance

    E-Print Network [OSTI]

    Effective Community-Wide Policy Technical Assistance: The DOE/NREL Approach NREL is a national: The DOE/NREL Approach Effective Community-Wide Policy Technical Assistance: The DOE/NREL Approach HelpingVoss, Sarah Busche, Eric Lantz, Lynn Billman, and Dan Beckley. The layout and technical editing were

  9. The NOvA Technical Design Report

    SciTech Connect (OSTI)

    Ayres, D.S.; Drake, G.R.; Goodman, M.C.; Grudzinski, J.J.; Guarino, V.J.; Talaga, R.L.; Zhao, A.; /Argonne; Stamoulis, P.; Stiliaris, E.; Tzanakos, G.; Zois, M.; /Athens U. /Caltech /UCLA /Fermilab /College de France /Harvard U. /Indiana U. /Lebedev Inst. /Michigan State U. /Minnesota U., Duluth /Minnesota U.

    2007-10-08T23:59:59.000Z

    Technical Design Report (TDR) describes the preliminary design of the NOvA accelerator upgrades, NOvA detectors, detector halls and detector sites. Compared to the March 2006 and November 2006 NOvA Conceptual Design Reports (CDR), critical value engineering studies have been completed and the alternatives still active in the CDR have been narrowed to achieve a preliminary technical design ready for a Critical Decision 2 review. Many aspects of NOvA described this TDR are complete to a level far beyond a preliminary design. In particular, the access road to the NOvA Far Detector site in Minnesota has an advanced technical design at a level appropriate for a Critical Decision 3a review. Several components of the accelerator upgrade and new neutrino detectors also have advanced technical designs appropriate for a Critical Decision 3a review. Chapter 1 is an Executive Summary with a short description of the NOvA project. Chapter 2 describes how the Fermilab NuMI beam will provide a narrow band beam of neutrinos for NOvA. Chapter 3 gives an updated overview of the scientific basis for the NOvA experiment, focusing on the primary goal to extend the search for {nu}{sub {mu}} {yields} {nu}{sub e} oscillations and measure the sin{sup 2}(2{theta}{sub 13}) parameter. This parameter has not been measured in any previous experiment and NOvA would extend the search by about an order of magnitude beyond the current limit. A secondary goal is to measure the dominant mode oscillation parameters, sin{sup 2}(2{theta}{sub 23}) and {Delta}m{sub 32}{sup 2} to a more precise level than previous experiments. Additional physics goals for NOvA are also discussed. Chapter 4 describes the Scientific Design Criteria which the Fermilab accelerator complex, NOvA detectors and NOvA detector sites must satisfy to meet the physics goals discussed in Chapter 3. Chapter 5 is an overview of the NOvA project. The changes in the design relative to the NOvA CDR are discussed. Chapter 6 summarizes the NOvA design performance relative to the Design Criteria set out in Chapter 4. Chapter 7 presents the Work Breakdown Structure dictionary at Level 3 and the Milestone dictionary. Chapters 8 through 17 then take each Level 2 WBS element of the NOvA project and present each part of the design in more detail than the overview given in Chapter 5. Specific technical design criteria are delineated for each part of the project in addition to the scientific design criteria outlined in Chapter 4. Changes in the design since the NOvA CDR are discussed in detail. The work remaining to bring each part of this preliminary design to a final design is outlined. Appendix A is a guide to other NOvA Project documentation with links to those documents.

  10. Final Scientific/Technical Report

    SciTech Connect (OSTI)

    Brown, R. C.; McCarley, T. M.

    2006-05-04T23:59:59.000Z

    The overall goal of this project was to establish an education and training program in biobased products at Iowa State University (ISU). In particular, a graduate program in Biorenewable Resources and Technology (BRT) was to be established as a way of offering students advanced study in the use of plant- and crop-based resources in the production of biobased products. The program was to include three fundamental elements: an academic program, a research program, and industrial interactions. The academic program set out to introduce a new graduate major in Biorenewable Resources and Technology. Unlike other schools, which only offer certificates or areas of emphasis in biobased products, Iowa State University offers both M.S. and Ph.D degrees through its graduate program. Core required courses in Biorenewable Resources and Technology include a foundation course entitled Fundamentals of Biorenewable Resources (BRT 501); a seminar course entitled Biobased Products Seminar (BRT 506); a laboratory course, and a special topics laboratory course. The foundation course is a three-credit course introducing students to basic concepts in biorenewable resources and technology. The seminar course provides students with an opportunity to hear from nationally and internationally recognized leaders in the field. The laboratory requirement is a 1-credit laboratory course or a special topics laboratory/research experience (BRT 591L). As part of student recruitment, quarter-time assistantships from DOE funds were offered to supplement assistantships provided by faculty to students. Research was built around platform teams in an effort to encourage interdisciplinary research and collaborative student learning in biorenewable resources. A platform is defined as the convergence of enabling technologies into a highly integrated system for transforming a specific feedstock into desired products. The platform teams parallel the way industry conducts research and product development. Platform teams organize faculty and students for cross-disciplinary, systems-oriented research and collaborative learning. To date, nine platforms have been developed, although these will most likely be reorganized into a smaller number of broader topics. In the spring of 2004, BRT faculty initiated a regional partnership and collaborative learning program with colleagues at the University of Minnesota, Kansas State University, and South Dakota State University to develop distance education courses in biorenewable resources and technology. As a fledgling graduate program, the BRT graduate program didn’t have the breadth of resources to offer a large number of courses in biorenewables. Other schools faced a similar problem. The academic consortium as first conceived would allow students from the member schools to enroll in biorenewables courses from any of the participating schools, which would assure the necessary enrollment numbers to offer specialized course work. Since its inception, the collaborative curriculum partnership has expanded to include Louisiana State University and the University of Wisconsin. A second international curriculum development campaign was also initiated in the spring of 2004. In particular, several BRT faculty teamed with colleagues at the University of Arkansas, University of Washington, University of Gent (Belgium), National Polytechnic Institute of Toulouse (France), and Technical University of Graz (Austria) to develop an EU-US exchange program in higher education and vocational education/training (entitled “Renewable Resources and Clean Technology”).

  11. PhD student in Energy Technology, specifically in New low GWP refrigerants

    E-Print Network [OSTI]

    Kazachkov, Ivan

    PhD student in Energy Technology, specifically in New low GWP refrigerants The School of Industrial, specifically New low GWP refrigerants. KTH is the largest technical university in Sweden. Education and Refrigeration The Division of Applied Thermodynamics and Refrigeration, part of the Department of Energy

  12. NREL scientists confirm the first molecular compound designed specifically to exhibit exciton multiplication.

    E-Print Network [OSTI]

    NREL scientists confirm the first molecular compound designed specifically to exhibit exciton designed with specific properties favorable for singlet fission. The stacking arrangement of molecules. Technical Contact: Justin Johnson, justin.johnson@nrel.gov References: Johnson, J.C.; Nozik, A.J.; Michl, J

  13. An evaluation of technical review of federal laboratory research: Findings from a US Department of Energy technical review pilot

    SciTech Connect (OSTI)

    Jordan, G.; Kuswa, G.; Mortensen, J.

    1998-06-01T23:59:59.000Z

    Recommendations for improving the process for expert panel reviews of technical and programmatic aspects of science and technology programs are provided based on an evaluation study of pilot reviews for two programs at Sandia National Laboratories. These reviews were part of a larger Technical Review Pilot for the US Department of Energy (DOE). Both the Sandia Pulse Power program and Solar Thermal Electric program (a virtual lab with NREL) reviews used the recommended four DOE review criteria, but motivation for the review and the review process differed. These differences provide insight into recommendations for ways to improve the review of DOE`s multifaceted technical programs. Recommendations are: (1) Review when the program has specific need for information or validation. There is no one size fits all correct time or reason to review technical programs. (2) Tailor the four DOE criteria to the program and its need for information and explain them to the Review Panel. (3) Pay attention to the review process. Spend more time in preparation and pre-review and on briefings on the review outcomes. (4) Evaluate reviews to determine how to do them better. The survey instrument is provided for those who wish to modify it for their own use.

  14. Final Technical Report

    SciTech Connect (OSTI)

    Sara Bergan, Executive Director; Brendan Jordan, Program Manager; Subcontractors as listed on the report.

    2007-06-06T23:59:59.000Z

    The following report contributes to our knowledge of how to economically produce wildlife-friendly grass mixtures for future fuel feedstocks in the northern plains. It investigates northern-adapted cultivars; management and harvest regimes that are good for yields, soils and wildlife; comparative analysis of monocultures and simple mixtures of native grasses; economic implications of growing grasses for fuel feedstocks in specific locations in the northern plains; and conversion options for turning the grasses into useful chemicals and fuels. The core results of this study suggest the following: ? Native grasses, even simple grass mixtures, can be produced profitably in the northern plains as far west as the 100th meridian with yields ranging from 2 to 6 tons per acre. ? Northern adapted cultivars may yield less in good years, but have much greater long-term sustainable yield potential than higher-yielding southern varieties. ? Grasses require very little inputs and stop economically responding to N applications above 56kg/hectare. ? Harvesting after a killing frost may reduce the yield available in that given year but will increase overall yields averaged throughout multiple years. ? Harvesting after a killing frost or even in early spring reduces the level of ash and undesirable molecules like K which cause adverse reactions in pyrolysis processing. Grasses can be managed for biomass harvest and maintain or improve overall soil-health and carbon sequestration benefits of idled grassland ? The carbon sequestration activity of the grasses seems to follow the above ground health of the biomass. In other words plots where the above ground biomass is regularly removed can continue to sequester carbon at the rate of 2 tons/acre/year if the stand health is strong and yielding significant amounts of biomass. ? Managing grasses for feedstock quality in a biomass system requires some of the same management strategies as managing for wildlife benefit. We believe that biomass development can be done in such a way that also maximizes or improves upon conservation and other environmental goals (in some cases even when compared to idled land). ? Switchgrass and big bluestem work well together in simple mixture plots where big bluestem fills in around the switchgrass which alone grows in bunches and leaves patches of bare soil open and susceptible to erosion. ? Longer-term studies in the northern plains may also find that every other year harvest schemes produce as much biomass averaged over the years as annual harvests ? Grasses can be grown for between $23 and $54/ton in the northern plains at production rates between 3 and 5 tons/acre. ? Land costs, yields, and harvest frequency are the largest determining factors in the farm scale economics. Without any land rent offset or incentive for production, and with annual harvesting, grass production is likely to be around $35/ton in the northern plains (farm gate). ? Average transportation costs range from $3 to $10/ton delivered to the plant gate. Average distance from the plant is the biggest factor - $3/ton at 10 miles, $10/ton at 50 miles. ? There is a substantial penalty paid on a per unit of energy produced basis when one converts grasses to bio-oil, but the bio-oil can then compete in higher priced fuel markets whereas grasses alone compete directly with relatively cheap coal. ? Bio oil or modified bio-oil (without the HA or other chemical fraction) is a suitable fuel for boiler and combustion turbines that would otherwise use residual fuel oil or number 2 diesel. ? Ensyn has already commercialized the use of HA in smokey flavorants for the food industry but that market is rather small. HA, however, is also found to be a suitable replacement for the much larger US market for ethanolamines and ethalyne oxides that are used as dispersants. ? Unless crude oil prices rise, the highest and best use of grass based bio-oil is primarily as a direct fuel. As prices rise, HA, phenol and other chemical fractions may become more attractive ? Although we were

  15. FINAL TECHNICAL REPORT

    SciTech Connect (OSTI)

    Loren F. Goodrich

    2011-05-31T23:59:59.000Z

    NIST has played a key role in many of the one-on-one, domestic, and international interlaboratory comparisons of measurements on superconductors. The history of interlaboratory comparisons of measurements on superconductors tells us that careful measurement methods are needed to obtain consistent results. Inconsistent results can lead to many problems including: a mistrust of the results of others, unfair advantages in commerce, and erroneous feedback in the optimization of conductor performance. NIST has experience in many interlaboratory comparisons; a long-term commitment to measurement accuracy; and independent, third-party laboratory status. The principal investigator's direct involvement in the measurements and daily supervision of sample mounting is the unique situation that has allowed important discoveries and evolution of our capabilities over the last 30 years. The principal investigator's research and metrology has helped to improve the accuracy of critical-current (I{sub c}) measurements in laboratories throughout the world. As conductors continue to improve and design limits are tested, the continuation of the long-term commitment to measurement accuracy could be vitally important to the success of new conductor development programs. It is extremely important to the U.S. wire manufacturers to get accurate (high certainty) I{sub c} measurements in order to optimize conductor performance. The optimization requires the adjustment of several fabrication parameters (such as reaction time, reaction temperature, conductor design, doping, diffusion barrier, Cu to non-Cu ratio, and twist pitch) based on the I{sub c} measurement of the conductor. If the I{sub c} measurements are made with high variability, it may be unclear whether or not the parameters are being adjusted in the optimal direction or whether or not the conductor meets the target specification. Our metrology is vital to the U.S. wire manufacturers in the highly competitive international arena and to meet the aggressive performance goals. The latest high-performance Nb{sub 3}Sn wires are being designed with higher current densities, larger effective filament diameter, less Cu stabilizer, and, in some cases, larger wire diameters than ever before. In addition, some of the conductor designs and heat treatments cause the residual resistivity ratio (RRR, ratio of room temperature resistivity to the resistivity at 20 K) of the stabilizer to be less than 20. These parameters are pushing the conductors towards less intrinsic stability, into a region we call marginally stable. These parameters also create a whole series of challenges for routine I{sub c} testing on short-samples, even when tested with the sample immersed in liquid helium. High-current, variable-temperature I{sub c} measurements are even more difficult than those made in liquid helium because the sample is only cooled by flowing helium gas. Providing accurate I{sub c} results under these conditions requires a complex system that provide adequate cooling as well as uniform sample temperature. We have been make variable-temperature measurements for about 15 years, but we started to design the first high-current (at least 500 A), variable-temperature, variable-strain apparatus in late 2006. Our first critical-current measurements as a function of strain, temperature, and magnetic field, I{sub c}(B,T,{var_epsilon}), in a new single, unified apparatus (full matrix characterization) were made in the summer of 2008. This is the only such facility in the U.S. and it has some unique components that are not duplicated anywhere in the world. The compounding of all three variables (H, T, {var_epsilon}) makes an already labor and time intensive characterization very formidable; however, the results cannot be generated any other way and are needed to answer key questions about strain and temperature safety margins and about the reliability of using scaling laws based on small data sets to predict performance. In the future, this new apparatus will allow NIST to create a database on strands that would benefit

  16. Final Technical Report

    SciTech Connect (OSTI)

    Dr. Asok K. Ray

    2012-05-22T23:59:59.000Z

    During the past decades, considerable theoretical efforts have been devoted to studying the electronic and geometric structures and related properties of surfaces. Such efforts are particularly important for systems like the actinides for which experimental work is relatively difficult to perform due to material problems and toxicity. The actinides are characterized by a gradual filling of the 5f-electron shell with the degree of localization increasing with the atomic number Z along the last series of the periodic table. The open shell of the 5f electrons determines the atomic, molecular, and solid state properties of the actinide elements and their compounds and understanding the quantum mechanics of the 5f electrons is the defining issue in the chemistry and physics of actinide elements. These elements are also characterized by the increasing prominence of relativistic effects and their studies can, in fact, help us understand the role of relativity throughout the periodic table. However, the electronic and geometric structures of the actinides, specifically the trans-uranium actinides and the roles of the 5f electrons in chemical bonding are still not well understood. This is crucial not only for our understanding of the actinides but also for the fact that the actinides constitute 'the missing link' between the d transition elements and the lanthanides. The 5f orbitals have properties intermediate between those of localized 4f and delocalized 3d orbitals. Thus, a proper understanding of the actinides will help us understand the behavior of the lanthanides and transition metals as well. In fact, there is an urgent need for continued extensive and detailed theoretical research in this area to provide significant and deep understandings of the electronic and geometric structures of the actinides. In this work, we have performed electronic structure studies for plutonium (Pu), americium (Am), and curium (Cm) surfaces, and molecular adsorptions on Pu and Am surfaces. In particular, the region at the boundary of Pu and Am, is widely believed to be the crossover region between d-like itinerant and f-like localized behavior The eventual goal is a complete understanding of the surface chemistry and physics processes of all actinide surfaces, defining the chemistry and physics of such heavy elements. Among the actinides, plutonium, with five 5f electrons in the solid state, is arguably the most complex, fascinating, and enigmatic element known to mankind and has attracted extraordinary scientific and technological interests because of its unique properties, generating a significant body of research in diverse areas, including superconductivity. Pu has, at least, six stable allotropes between room temperature and melting at atmospheric pressure, indicating that the valence electrons can hybridize into a number of complex bonding arrangements. Central and critical questions relate to the electronic structure, localization of the 5f electrons and the magnetism of Pu. For the light-actinides, from Th to Pu, the 5f electrons are believed to be delocalized, hybridizing with the 6d and 7s electrons. For the heavier actinides, Am and beyond, the 5f electrons are localized with the 5f orbitals progressively lower in energy relative to the 6d configuration. Hence, Pu is in a position where the 5f electronic behavior changes from itinerant to localized. As far as magnetism is concerned, a majority of the theoretical calculations continues to claim the existence of magnetism while almost all the experimental results do not find any support for such claims. The second element of interest to us, namely americium, occupies a central position in the actinide series with respect to the involvement of 5f electrons in metallic bonding. It is widely believed that the 5f electrons in Am are localized and that Am undergoes a series of crystallographic phase changes with pressure. Fully-relativistic all electron surface studies of the different phases of Am, initially for the dhcp and the fcc surfaces, can and have provided us with valuable informa

  17. Linac4 Technical Design Report

    E-Print Network [OSTI]

    Arnaudon, L; Baylac, M; Bellodi, G; Body, Y; Borburgh, J; Bourquin, P; Broere, J; Brunner, O; Bruno, L; Carli, C; Caspers, Friedhelm; Cousineau, S M; Cuvet, Y; De Almeida Martins, C; Dobers, T; Fowler, T; Garoby, R; Gerigk, F; Goddard, B; Hanke, K; Hori, M; Jones, M; Kahle, K; Kalbreier, Willi; Kroyer, T; Küchler, D; Lombardi, A M; López-Hernandez, L A; Magistris, M; Martini, M; Maury, S; Page, E; Paoluzzi, M; Pasini, M; Raich, U; Rossi, C; Royer, J P; Sargsyan, E; Serrano, J; Scrivens, R; Silari, M; Timmins, M; Venturini-Delsolaro, W; Vretenar, M; Wegner, R; Weterings, W; Zickler, T

    2006-01-01T23:59:59.000Z

    Linac4 is an H- linear accelerator, intended to replace Linac2 as injector to the PS Booster (PSB). By delivering to the PSB a beam at 160 MeV energy, Linac4 will provide the conditions to double the brightness and intensity of the beam from the PSB, thus removing the first bottleneck towards higher brightness for the LHC and simplifying operation. Moreover, this new linac constitutes an essential component of any of the envisaged LHC upgrade scenarios and could open the way to future extensions of the CERN accelerator complex towards higher performance. This Technical Design Report presents a detailed technical overview of the Linac4 design as it stands at end 2006.

  18. FLAMMABLE GAS TECHNICAL BASIS DOCUMENT

    SciTech Connect (OSTI)

    KRIPPS, L.J.

    2005-02-18T23:59:59.000Z

    This document describes the qualitative evaluation of frequency and consequences for double shell tank (DST) and single shell tank (SST) representative flammable gas accidents and associated hazardous conditions without controls. The evaluation indicated that safety-significant SSCs and/or TSRS were required to prevent or mitigate flammable gas accidents. Discussion on the resulting control decisions is included. This technical basis document was developed to support of the Tank Farms Documented Safety Analysis (DSA) and describes the risk binning process for the flammable gas representative accidents and associated represented hazardous conditions. The purpose of the risk binning process is to determine the need for safety-significant structures, systems, and components (SSC) and technical safety requirement (TSR)-level controls for a given representative accident or represented hazardous condition based on an evaluation of the event frequency and consequence.

  19. McKenzie River Subbasin Assessment, Technical Report 2000.

    SciTech Connect (OSTI)

    Alsea Geospatial, Inc.

    2000-02-01T23:59:59.000Z

    This document details the findings of the McKenzie River Subbasin Assessment team. The goal of the subbasin assessment is to provide an ecological assessment of the McKenzie River Floodplain, identification of conservation and restoration opportunities, and discussion of the influence of some upstream actions and processes. This Technical Report can be viewed in conjunction with the McKenzie River Subbasin Summary or as a stand-alone document. The purpose of the technical report is to detail the methodology and findings of the consulting team that the observations and recommendations in the summary document are based on. This part, Part I, provides an introduction to the subbasin and a general overview. Part II details the specific findings of the science team. Part III provides an explanation and examples of how to use the data that has been developed through this assessment to aid in prioritizing restoration activities. Part III also includes the literature cited and appendices.

  20. FACILITY WORKER TECHNICAL BASIS DOCUMENT

    SciTech Connect (OSTI)

    SHULTZ, M.V.

    2005-03-31T23:59:59.000Z

    This technical basis document was developed to support RPP-13033, ''Tank Farms Documented Safety Analysis (DSA). It describes the criteria and methodology for allocating controls to hazardous conditions with significant facility worker (FW) consequence and presents the results of the allocation. The criteria and methodology for identifying controls that address FW safety are in accordance with DOE-STD-3009-94, ''Preparation Guide for US Department of Energy Nonreactor Nuclear Facility Documented Safety Analyses''.

  1. Technical Assistance | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious Rank EERE: Alternative Fuels Data Center HomeIdle ReductionOffices Offices AllFeeds RSSSustainableTechnical

  2. Development of superior asphalt recycling agency: Phase 1, Technical feasibility. Technical progress report

    SciTech Connect (OSTI)

    Bullin, J.A.; Glover, C.J.; Davison, R.R.; Lin, Moon-Sun; Chaffin, J.; Liu, Meng; Eckhardt, C.

    1996-04-01T23:59:59.000Z

    About every 12 years, asphalt roads must be reworked, and this is usually done by placing thick layers (hot-mix overlays) of new material on top of failed material, resulting in considerable waste of material and use of new asphalt binder. A good recycling agent is needed, not only to reduce the viscosity of the aged material but also to restore compatibility. Objective is to establish the technical feasibility (Phase I) of determining the specifications and operating parameters for producing high quality recycling agents which will allow most/all the old asphalt-based road material to be recycled. It is expected that supercritical fractionation can be used. The advanced road aging simulation procedure will be used to study aging of blends of old asphalt and recycling agents.

  3. IDC System Specification Document.

    SciTech Connect (OSTI)

    Clifford, David J.

    2014-12-01T23:59:59.000Z

    This document contains the system specifications derived to satisfy the system requirements found in the IDC System Requirements Document for the IDC Reengineering Phase 2 project. Revisions Version Date Author/Team Revision Description Authorized by V1.0 12/2014 IDC Reengineering Project Team Initial delivery M. Harris

  4. Plume measurement system (PLUMES) technical manual and data analysis procedures. Final report

    SciTech Connect (OSTI)

    Tubman, M.W.

    1995-02-01T23:59:59.000Z

    The PLUmes MEasurement System (PLUMES) was developed under the Measurement of Entrainment and Transport work unit, Dredging Research Program Technical Area 1, Analysis of Dredged Material Placed in Open Water, to monitor the transport of suspended sediment from dredging and dredged material disposal operations. This system can monitor the transport nearly synoptically, both horizontally and vertically. This report provides technical information on the overall system, guidance on locating specific information in the standard technical manuals provided by the manufacturers of the individual system components, technical information on special features of the system components not included in the manufacturer`s manuals, information on system operation and deployment procedures, descriptions of the PLUMES software, and information on the data analysis procedures.

  5. Technical Report Confirms Reliability of Yucca Mountain Technical Work |

    Energy Savers [EERE]

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page onYou are now leaving Energy.gov You are now leaving Energy.gov You are being directedAnnual Siteof Energy 2, 2015 - January 16,Administrative Forms TechnicalDepartment of Energy

  6. Changing fuel specifications

    SciTech Connect (OSTI)

    Hatt, R.

    1995-08-01T23:59:59.000Z

    This paper will describe the goals, methods, and results of a program designed to expand fuel specifications. The ability to expand fuel specs can provide many advantages to a power company. These would include increased fuel flexibility, better performance and lower fuel cost. The expansion of transportation modes also may enhance the scenario. Although brief, this paper should provide a good understanding of the types of problems that can be encountered, and the cooperative effort necessary to resolve them.

  7. Technical Specifications and Usage Procedures and Policies Contact Technical Director Peter Davis at 912.478.7916 with questions regarding technical

    E-Print Network [OSTI]

    Hutcheon, James M.

    information is to be arranged through the House Manager. Programs must include FOH information sheet. Reminder: The Performing Arts Center is not liable for loss of or damage to personal property. STAGE DIMENSIONS Proscenium instructions and leave the building as quickly as possible. The Production Manager or Stage Manager is to take

  8. Sludge Treatment Evaluation: 1992 Technical progress

    SciTech Connect (OSTI)

    Silva, L J; Felmy, A R; Ding, E R

    1993-01-01T23:59:59.000Z

    This report documents Fiscal Year 1992 technical progress on the Sludge Treatment Evaluation Task, which is being conducted by Pacific Northwest Laboratory. The objective of this task is to develop a capability to predict the performance of pretreatment processes for mixed radioactive and hazardous waste stored at Hanford and other US Department of Energy (DOE) sites. Significant cost savings can be achieved if radionuclides and other undesirable constituents can be effectively separated from the bulk waste prior to final treatment and disposal. This work is initially focused on chemical equilibrium prediction of water washing and acid or base dissolution of Hanford single-shell tank (SST) sludges, but may also be applied to other steps in pretreatment processes or to other wastes. Although SST wastes contain many chemical species, there are relatively few constituents -- Na, Al, NO[sub 3], NO[sub 2], PO[sub 4], SO[sub 4], and F -- contained in the majority of the waste. These constituents comprise 86% and 74% of samples from B-110 and U-110 SSTS, respectively. The major radionuclides of interest (Cs, Sr, Tc, U) are present in the sludge in small molal quantities. For these constituents, and other important components that are present in small molal quantities, the specific ion-interaction terms used in the Pitzer or NRTL equations may be assumed to be zero for a first approximation. Model development can also be accelerated by considering only the acid or base conditions that apply for the key pretreatment steps. This significantly reduces the number of chemical species and chemical reactions that need to be considered. Therefore, significant progress can be made by developing all the specific ion interactions for a base model and an acid dissolution model.

  9. Scientific and Technical Information Management

    Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

    2001-04-09T23:59:59.000Z

    To establish Department of Energy (DOE) requirements and responsibilities to ensure that scientific and technical information (STI) is identified, processed, disseminated, and preserved in a manner that (a) enables the scientific community and the public to locate and use the unclassified and unlimited STI resulting from DOE's research and related endeavors and (b) ensures access to classified and sensitive unclassified STI is protected according to legal or Departmental requirements. Cancels DOE O 241.1. Canceled by DOE O 241.1A Chg 1.

  10. PVWatts Version 1 Technical Reference

    SciTech Connect (OSTI)

    Dobos, A. P.

    2013-10-01T23:59:59.000Z

    The NREL PVWatts(TM) calculator is a web application developed by the National Renewable Energy Laboratory (NREL) that estimates the electricity production of a grid-connected photovoltaic system based on a few simple inputs. PVWatts combines a number of sub-models to predict overall system performance, and makes several hidden assumptions about performance parameters. This technical reference details the individual sub-models, documents assumptions and hidden parameters, and explains the sequence of calculations that yield the final system performance estimation.

  11. Technical Assistance | Department of Energy

    Energy Savers [EERE]

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page onYou are now leaving Energy.gov You are now leaving Energy.gov You are being directed offOCHCO Overview OCHCOSystems Analysis Success Stories SystemsTara Trujillo AboutTechnical

  12. Technical Assistance | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page onYouTube YouTube Note: Since the.pdfBreakingMayDepartment ofEnergyTeam Cumberland » TeamTechnical Assistance

  13. SAM Photovoltaic Model Technical Reference

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level:Energy: Grid Integration Redefining What's PossibleRadiation Protection TechnicalResonantNovember 15Rotary FiringRobertSAC HomePastSAM

  14. Report Back from Technical Editor

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level:Energy: Grid Integration Redefining What's PossibleRadiation Protection Technical s o Freiberge s 3 % A PB 2 7 7 2 x> - ^Rep.LANSv_^ '

  15. Technical Reports | ornl.gov

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645U.S. DOE Office of ScienceandMesa del SolStrengthening a solidSynthesis of 2D AlloysTrails News Home |21-6-9Technical

  16. TECHNICAL ADVANCEMENTS AND ISSUES ASSOCIATED WITH

    E-Print Network [OSTI]

    of Energy United States Nuclear Waste Technical Review Board #12;#12;U.S. Nuclear Waste Technical Review in the report are those of the Board and not necessarily those of the reviewers. #12;U.S. NUCLEAr WASTE TECh.D., P.E. Duke University Durham, North Carolina #12;NUCLEAr WASTE TEChNiCAL rEviEW BOArD STAff EXECUTIVE

  17. Establishment of the International Power Institute. Final technical report

    SciTech Connect (OSTI)

    Julius E. Coles

    2000-08-04T23:59:59.000Z

    The International Power Institute, in collaboration with American industries, seeks to address technical, political, economic and cultural issues of developing countries in the interest of facilitating profitable transactions in power related infrastructure projects. IPI works with universities, governments and commercial organizations to render project-specific recommendations for private-sector investment considerations. IPI also established the following goals: Facilitate electric power infrastructure transactions between developing countries and the US power industry; Collaborate with developing countries to identify development strategies to achieve energy stability; and Encourage market driven solutions and work collaboratively with other international trade energy, technology and banking organizations.

  18. Usability of digital libraries: a source of creative tensions with technical developments

    E-Print Network [OSTI]

    Blandford, Ann

    Usability of digital libraries: a source of creative tensions with technical developments Ann If digital libraries are to achieve their full potential, they need to be usable and used ­ by people of `usability' and how they apply specifically to digital libraries. There are great challenges to integrating

  19. Proceedings of IDETC/CIE 2005 ASME 2005 International Design Engineering Technical Conferences

    E-Print Network [OSTI]

    Moehlis, Jeff

    of the system. Rather, such systems exhibit branch- specific nonlinearities which, when collectively analyzedProceedings of IDETC/CIE 2005 ASME 2005 International Design Engineering Technical Conferences;such systems can exhibit not only typical softening or hardening behavior, but also mixed behavior

  20. GENERAL TECHNICAL REPORT PSW-GTR-240 Breeding for Disease Resistance in Hevea spp. -

    E-Print Network [OSTI]

    Standiford, Richard B.

    GENERAL TECHNICAL REPORT PSW-GTR-240 240 Breeding for Disease Resistance in Hevea spp. - Status be implemented to tackle such future threats of epidemics. Hevea clones clearly exhibit variable levels from H. benthamiana "F4542." Few other attempts for inter-specific hybridization have been made

  1. ACI Materials Journal/September-October 2009 1 ACI MATERIALS JOURNAL TECHNICAL PAPER

    E-Print Network [OSTI]

    ACI Materials Journal/September-October 2009 1 ACI MATERIALS JOURNAL TECHNICAL PAPER ACI Materials-cured for 7 days exhibited the highest compressive strengths at ages of 28 and 56 days. In contrast, 1-day. Although some design specifications have addressed the use of HSC, many have implicitly or explicitly

  2. Information and Telecommunication Technology Center, Technical Report: ITTC-FY97-11100-1.

    E-Print Network [OSTI]

    Kansas, University of

    Information and Telecommunication Technology Center, Technical Report: ITTC- FY97 almost impossible for a casual user to look for specific information without getting lost among huge with search systems that exhibit an above average degree of agency or incorporate learning capabilities

  3. Technical Report: Michigan Department of Environmental Quality, Michigan Great Lakes Protection Fund

    E-Print Network [OSTI]

    Denver, Robert J.

    1 Technical Report: Michigan Department of Environmental Quality, Michigan Great Lakes Protection (TTR). In mammals, TTR is a T4-specific binding protein. However, in nonmammalian species, TTR binds 3 competitive binding assays with several PCB congeners or hydroxylated PCBs to determine whether they exhibit

  4. Proceedings of the ASME 2010 International Design Engineering Technical Conferences & Computers and Information in Engineering Conference

    E-Print Network [OSTI]

    Dollar, Aaron M.

    Proceedings of the ASME 2010 International Design Engineering Technical Conferences & Computers in. Specifically, we show that in conditions when the actuator position is fixed, hands with single-acting mechanisms exhibit a bimodal behavior in contrast to hands with double-acting mechanisms that exhibit

  5. Technical Qualification Program Description - Integrated Support...

    Broader source: Energy.gov (indexed) [DOE]

    to begin the 18 month qualification period). Technical Qualification Program Description Revision 2, November 2010 5 The position's inclusion in the TQP is: * Specified in the PD...

  6. Technical Position, Regarding Acceptable Methods for Assessing...

    Office of Environmental Management (EM)

    Regarding Acceptable Methods for Assessing and Recording Radiation Doses to Individuals Technical Position, Regarding Acceptable Methods for Assessing and Recording Radiation Doses...

  7. Dampers for Natural Draft Heaters: Technical Report

    E-Print Network [OSTI]

    Lutz, James D.

    2009-01-01T23:59:59.000Z

    Oil? Fired Residential Water Heaters. Berkeley Heights, Newof Residential Gas Water Heaters. Chicago, IL, Gas ApplianceDampers for Natural Draft Water Heaters: Technical Report.

  8. Technical Consultant Contract | Department of Energy

    Energy Savers [EERE]

    Program (STEP). C3c Technical Consultant Contract.pdf More Documents & Publications Communication Consultant Contract Communications Consultant RFP Loan Loss Reserve Agreement...

  9. APPA Engineering and Operations Technical Conference

    Office of Energy Efficiency and Renewable Energy (EERE)

    The 2014 APPA Engineering and Operations Technical Conference is designed for public power professionals charged with designing, developing, and maintaining the nation's electric system.

  10. Space Conditioning Standing Technical Committee Strategic Plan...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Committee Strategic Plan Space Conditioning Standing Technical Committee Strategic Plan This strategic plan document outlines the gaps, barriers, and opportunities identified by...

  11. TR-003 Ecology March 2000 Technical Report

    E-Print Network [OSTI]

    TR-003 Ecology March 2000 Technical Report Research Disciplines: Ecology ~ Geology ~ Geomorphology: Ecology ~ Geology ~ Geomorphology ~ Hydrology ~ Pedology ~ Silviculture ~ Wildlife CONTENTS ABSTRACT

  12. Technical Standards, Program Project Justification Statement...

    Energy Savers [EERE]

    Standards, Program Project Justification Statement - August 29, 2012 August 29, 2012 DOE Technical Standards Program Project Justification Statement As part of the new...

  13. FAQS Reference Guide – General Technical Base

    Broader source: Energy.gov [DOE]

    This reference guide addresses the competency statements in the December 2007 edition of DOE-STD-1146-2007, General Technical Base Functional Area Qualification Standard.

  14. Technical Report Documentation Page 1. Report No.

    E-Print Network [OSTI]

    Texas at Austin, University of

    Technical Report Documentation Page 1. Report No. 1732-S 2. Government Accession No. 3. Recipients, geometric design, entrance ramps, exit ramps 18. Distribution Statement No restrictions. This document

  15. PRELIMINARY REVIEW COPY Technical Report Documentation Page

    E-Print Network [OSTI]

    Texas at Austin, University of

    PRELIMINARY REVIEW COPY Technical Report Documentation Page 1. Report No. 2941-3 Preliminary Review, long-term monitoring 18. Distribution Statement No restrictions. This document is available

  16. Oak Ridge Site Specific

    Office of Environmental Management (EM)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742 33Frequently Asked QuestionsDepartment ofDepartment640OrderOREMJanuary 20149Oak RidgeSite Specific

  17. Specific Group Hardware

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645U.S. DOE Office of ScienceandMesa del Sol HomeFacebookScholarship Fund3Biology|SolarSpeakers BureauSpecialSpecific Group

  18. Roadmap: Technical and Applied Studies NonprofitHuman Services Bachelor of Technical and Applied Studies

    E-Print Network [OSTI]

    Sheridan, Scott

    Roadmap: Technical and Applied Studies ­ Nonprofit­Human Services ­ Bachelor of Technical-Aug-12/TET This roadmap is a recommended semester-by-semester plan of study for this major. However / SOC 32570 COMM 35864, COMT 36318 or Visit www.kent.edu/catalog/elr 2.000 2.000 #12;Roadmap: Technical

  19. Next Generation Nuclear Plant Project Technology Development Roadmaps: The Technical Path Forward for 750–800°C Reactor Outlet Temperature

    SciTech Connect (OSTI)

    John Collins

    2009-08-01T23:59:59.000Z

    This document presents the NGNP Critical PASSCs and defines their technical maturation path through Technology Development Roadmaps (TDRMs) and their associated Technology Readiness Levels (TRLs). As the critical PASSCs advance through increasing levels of technical maturity, project risk is reduced and the likelihood of within-budget and on-schedule completion is enhanced. The current supplier-generated TRLs and TDRMs for a 750–800°C reactor outlet temperature (ROT) specific to each supplier are collected in Appendix A.

  20. Technical Insights for Saltstone PA Maintenance

    SciTech Connect (OSTI)

    Flach, G.; Sarkar, S.; Mahadevan, S.; Kosson, D.

    2011-07-20T23:59:59.000Z

    The Cementitious Barriers Partnership (CBP) is a collaborative program sponsored by the US DOE Office of Waste Processing. The objective of the CBP is to develop a set of computational tools to improve understanding and prediction of the long-term structural, hydraulic, and chemical performance of cementitious barriers and waste forms used in nuclear applications. CBP tools are expected to better characterize and reduce the uncertainties of current methodologies for assessing cementitious barrier performance and increase the consistency and transparency of the assessment process, as the five-year program progresses. In September 2009, entering its second year of funded effort, the CBP sought opportunities to provide near-term tangible support to DOE Performance Assessments (PAs). The Savannah River Saltstone Disposal Facility (SDF) was selected for the initial PA support effort because (1) cementitious waste forms and barriers play a prominent role in the performance of the facility, (2) certain important long-term behaviors of cementitious materials composing the facility are uncertain, (3) review of the SDF PA by external stakeholders is ongoing, and (4) the DOE contractor responsible for the SDF PA is open to receiving technical assistance from the CBP. A review of the current (SRR Closure & Waste Disposal Authority 2009) and prior Saltstone PAs (e.g., Cook et al. 2005) suggested five potential opportunities for improving predictions. The candidate topics considered were (1) concrete degradation from external sulfate attack, (2) impact of atmospheric exposure to concrete and grout before closure, such as accelerated slag and Tc-99 oxidation, (3) mechanistic prediction of geochemical conditions, (4) concrete degradation from rebar corrosion due to carbonation, and (5) early age cracking from drying and/or thermal shrinkage. The candidate topics were down-selected considering the feasibility of addressing each issue within approximately six months, and compatibility with existing CBP expertise and already-planned activities. Based on these criteria, the five original topics were down-selected to two: external sulfate attack and mechanistic geochemical prediction. For each of the selected topics, the CBP communicated with the PA analysts and subject matter experts at Savannah River to acquire input data specific to the Saltstone facility and related laboratory experiments. Simulations and analyses were performed for both topics using STADIUM (SIMCO 2008), LeachXS/ORCHESTRA (ECN 2007, Meeussen 2003), and other software tools. These supplemental CBP analyses produced valuable technical insights that can be used to strengthen the Saltstone PA using the ongoing PA maintenance process. This report in part summarizes key information gleaned from more comprehensive documents prepared by Sarkar et al. (2010), Samson (2010), and Sarkar (2010).

  1. Technical data base quarterly report, April--June 1992; Yucca Mountain Site Characterization Project

    SciTech Connect (OSTI)

    NONE

    1992-09-01T23:59:59.000Z

    The acquisition and development of technical data are activities that provide the information base from which the Yucca mountain Site will be characterized and may P-ventually be licensed as a high-level waste repository. The Project Technical Data Base (TDB) is the repository for the regional and site-specific technical data required in intermediate and license application analyses and models. The TDB Quarterly Report provides the mechanism for identifying technical data currently available from the Project TDB. Due to the variety of scientific information generated by YMP activities, the Project TDB consists of three components, each designed to store specific types of data. The Site and Engineering Properties Data Base (SEPDB) maintains technical data best stored in a tabular format. The Geographic Nodal Information Study and Evaluation System (GENISES), which is the Geographic Information System (GIS) component of the Project TDB, maintains spatial or map-like data. The Geologic and Engineering Materials Bibliography of Chemical Species (GEMBOCHS) data base maintains thermodynamic/geochemical data needed to support geochemical reaction models involving the waste package and repository geochemical environment. Each of these data bases are addressed independently within the TDB Quarterly Report.

  2. Cylinder Test Specification

    SciTech Connect (OSTI)

    Richard Catanach; Larry Hill; Herbert Harry; Ernest Aragon; Don Murk

    1999-10-01T23:59:59.000Z

    The purpose of the cylinder testis two-fold: (1) to characterize the metal-pushing ability of an explosive relative to that of other explosives as evaluated by the E{sub 19} cylinder energy and the G{sub 19} Gurney energy and (2) to help establish the explosive product equation-of-state (historically, the Jones-Wilkins-Lee (JWL) equation). This specification details the material requirements and procedures necessary to assemble and fire a typical Los Alamos National Laboratory (LANL) cylinder test. Strict adherence to the cylinder. material properties, machining tolerances, material heat-treatment and etching processes, and high explosive machining tolerances is essential for test-to-test consistency and to maximize radial wall expansions. Assembly and setup of the cylinder test require precise attention to detail, especially when placing intricate pin wires on the cylinder wall. The cylinder test is typically fired outdoors and at ambient temperature.

  3. UNITED STATES NUCLEAR WASTE TECHNICAL REVIEW BOARD

    E-Print Network [OSTI]

    con144vf UNITED STATES NUCLEAR WASTE TECHNICAL REVIEW BOARD 2300 Clarendon Boulevard, Suite 1300 Dear Speaker Hastert, Senator Thurmond, and Secretary Richardson: The Nuclear Waste Technical Review with provisions of the Nuclear Waste Policy Amendments Act of 1987, Public Law 100-203. The Act requires the Board

  4. Appendix A Nuclear Waste Technical Review Board

    E-Print Network [OSTI]

    39 Appendices Appendices #12;Appendix A Nuclear Waste Technical Review Board Members: Curricula to the Nuclear Waste Technical Review Board. President Clinton appointed Dr. Cohon chairman on January 17, 1997, and Asia and on energy facility siting, including nuclear waste ship- ping and storage. In addition to his

  5. Appendix A Nuclear Waste Technical Review Board

    E-Print Network [OSTI]

    59 Appendices Appendices #12;Appendix A Nuclear Waste Technical Review Board Members: Curricula Cohon to serve on the Nuclear Waste Technical Review Board. President Clinton appointed Dr. Cohon, and Asia and on energy-facility siting, including nuclear waste shipping and storage. In addition to his

  6. UNITED STATES NUCLEAR WASTE TECHNICAL REVIEW BOARD

    E-Print Network [OSTI]

    UNITED STATES NUCLEAR WASTE TECHNICAL REVIEW BOARD 2300 Clarendon Boulevard, Suite 1300 Arlington.C. 20585 Dear Speaker Hastert, Senator Stevens, and Secretary Bodman: The Nuclear Waste Technical Review Board was created by Congress in the Nuclear Waste Policy Amendments Act (NWPAA) of 1987 and charged

  7. UNITED STATES NUCLEAR WASTE TECHNICAL REVIEW BOARD

    E-Print Network [OSTI]

    JEC187V3 UNITED STATES NUCLEAR WASTE TECHNICAL REVIEW BOARD 2300 Clarendon Boulevard, Suite 1300 of Energy 1000 Independence Avenue, SW Washington, DC 20585 Dear Secretary O'Leary: At the Nuclear Waste UNITED STATES NUCLEAR WASTE TECHNICAL REVIEW BOARD 2300 Clarendon Boulevard, Suite 1300 Arlington, VA

  8. UNITED STATES NUCLEAR WASTE TECHNICAL REVIEW BOARD

    E-Print Network [OSTI]

    UNITED STATES NUCLEAR WASTE TECHNICAL REVIEW BOARD 2300 Clarendon Boulevard, Suite 1300 Arlington Dear Speaker Pelosi, Senator Byrd, and Secretary Bodman: The Nuclear Waste Technical Review Board, and transporting high-level radioactive waste and spent nuclear fuel. The Board is required to report its findings

  9. Water Resources Center Annual Technical Report

    E-Print Network [OSTI]

    Inactivation of Microorganisms in Drinking Water using Ultraviolet (UV) Radiation and Residual Chlorine. DrWater Resources Center Annual Technical Report FY 2009 Water Resources Center Annual Technical Report FY 2009 1 #12;Introduction This is a report on the projects of the Rhode Island Water Resources

  10. UNITED STATES NUCLEAR WASTE TECHNICAL REVIEW BOARD

    E-Print Network [OSTI]

    of the overall system for managing spent fuel and defense high-level waste. The Board includes its findingsjlc029va UNITED STATES NUCLEAR WASTE TECHNICAL REVIEW BOARD 2300 Clarendon Boulevard, Suite 1300, D.C. 20585 Dear Speaker Gingrich, Senator Thurmond, and Secretary Peña: The Nuclear Waste Technical

  11. Water Resources Center Annual Technical Report

    E-Print Network [OSTI]

    Water Resources Center Annual Technical Report FY 2001 Introduction Three research projects were. The technical transfer project set up a RI Water Resources Center Website to allow easy access to the Center treatment devices, such as oil/sediment separators, that have been widely installed in urbanized areas have

  12. Arkansas Water Resources Center Annual Technical Report

    E-Print Network [OSTI]

    Arkansas Water Resources Center Annual Technical Report FY 2010 Arkansas Water Resources Center Annual Technical Report FY 2010 1 #12;Introduction The Arkansas Water Resources Center located at the University of Arkansas, Fayetteville, Arkansas is part of the network of 54 water institutes established

  13. Arkansas Water Resources Center Annual Technical Report

    E-Print Network [OSTI]

    Arkansas Water Resources Center Annual Technical Report FY 2011 Arkansas Water Resources Center Annual Technical Report FY 2011 1 #12;Introduction The Arkansas Water Resources Center located at the University of Arkansas at Fayetteville, is part of the network of 54 water institutes established

  14. Colorado Water Institute Annual Technical Report

    E-Print Network [OSTI]

    Colorado Water Institute Annual Technical Report FY 2012 Colorado Water Institute Annual Technical Report FY 2012 1 #12;Introduction Colorado Water Institute Annual Report for the period: March 1, 2012 ­ February 28, 2013 Water research is more pertinent than ever in Colorado. Whether the project explores

  15. Colorado Water Institute Annual Technical Report

    E-Print Network [OSTI]

    Colorado Water Institute Annual Technical Report FY 2011 Colorado Water Institute Annual Technical Report FY 2011 1 #12;Introduction Water research is more pertinent than ever in Colorado. Whether the project explores the effects of decentralized wastewater treatment systems on water quality, optimal

  16. Arkansas Water Resources Center Annual Technical Report

    E-Print Network [OSTI]

    Arkansas Water Resources Center Annual Technical Report FY 2013 Arkansas Water Resources Center Annual Technical Report FY 2013 1 #12;Introduction The Arkansas Water Resources Center is part of the network of 54 water institutes established by the Water Resources Research Act of 1964 and is located

  17. Arkansas Water Resources Center Annual Technical Report

    E-Print Network [OSTI]

    Arkansas Water Resources Center Annual Technical Report FY 2009 Arkansas Water Resources Center Annual Technical Report FY 2009 1 #12;Introduction The Arkansas Water Resources Center located at the University of Arkansas, Fayetteville, Arkansas is part of the network of 54 water institutes established

  18. Colorado Water Institute Annual Technical Report

    E-Print Network [OSTI]

    Colorado Water Institute Annual Technical Report FY 2013 Colorado Water Institute Annual Technical Report FY 2013 1 #12;Introduction Water research is more important than ever in Colorado. Whether the project explores the effects of decentralized wastewater treatment systems on water quality, optimal

  19. Colorado Water Institute Annual Technical Report

    E-Print Network [OSTI]

    Colorado Water Institute Annual Technical Report FY 2009 Colorado Water Institute Annual Technical Report FY 2009 1 #12;Introduction Water research is more pertinent than ever in Colorado. Whether the research explores the effects of decentralized wastewater treatment systems on water quality, optimal

  20. Water Resources Center Annual Technical Report

    E-Print Network [OSTI]

    Water Resources Center Annual Technical Report FY 2007 Water Resources Center Annual Technical Report FY 2007 1 #12;Introduction The Rhode Island Water Resources Center has supported one information transfer project, "Clean Drinking Water in Rhode Island" and one research project "Enhancing Drinking Water

  1. Iowa Water Center Annual Technical Report

    E-Print Network [OSTI]

    Iowa Water Center Annual Technical Report FY 2010 Iowa Water Center Annual Technical Report FY 2010 1 #12;Introduction The Iowa Water Center is a multi-campus and multi-organizational center focusing-institutional water research that can improve Iowa's water quality and provide adequate water supplies to meet both

  2. Iowa Water Center Annual Technical Report

    E-Print Network [OSTI]

    Iowa Water Center Annual Technical Report FY 2011 Iowa Water Center Annual Technical Report FY 2011 1 #12;Introduction The Iowa Water Center is a multi-campus and multi-organizational center focusing-institutional water research that can improve Iowa's water quality and provide adequate water supplies to meet both

  3. Iowa Water Center Annual Technical Report

    E-Print Network [OSTI]

    Iowa Water Center Annual Technical Report FY 2012 Iowa Water Center Annual Technical Report FY 2012 1 #12;Introduction The Iowa Water Center is a multi-campus and multi-organizational center focusing-institutional water research that can improve Iowa's water quality and provide adequate water supplies to meet both

  4. Colorado Water Institute Annual Technical Report

    E-Print Network [OSTI]

    Colorado Water Institute Annual Technical Report FY 2010 Colorado Water Institute Annual Technical Report FY 2010 1 #12;Introduction Water research is more pertinent than ever in Colorado. Whether the project explores the effects of decentralized wastewater treatment systems on water quality, optimal

  5. Managing Technical Risk: Understanding Private Sector

    E-Print Network [OSTI]

    action. Our study seeks to inform the decisions of both government managers and private entrepreneursApril 2000 Managing Technical Risk: Understanding Private Sector Decision Making on Early Stage 00-787 Managing Technical Risk Understanding Private Sector Decision Making on Early Stage Technology

  6. Water Resources Center Annual Technical Report

    E-Print Network [OSTI]

    , and nitrogen in non-conventional onsite wastewater treatment processes: a technical and economic analysis Basic treatment processes: a technical and economic analysis Project Number: 2002CA1B Start Date: 3/1/2002 End for the Onsite Treatment of Wastewater in California, Center for Water Resources Engineering, University

  7. Waste transfer leaks technical basis document

    SciTech Connect (OSTI)

    ZIMMERMAN, B.D.

    2003-03-22T23:59:59.000Z

    This document provides technical support for the onsite radiological and toxicological, and offsite toxicological, portions of the waste transfer leak accident presented in the Documented Safety Analysis. It provides the technical basis for frequency and consequence bin selection, and selection of safety SSCs and TSRs.

  8. Technical Report Documentation Page 1. Report No.

    E-Print Network [OSTI]

    Texas at Austin, University of

    Technical Report Documentation Page 1. Report No. FHWA/TX-05 / 0-4562-1 2.Government accession No and Friction Losses in Multi-Strand Post- Tensioning Tendons Including the Effects of Emulsifiable Oils 6 Austin, TX 78705-2650 11. Contract or Grant No. 0-4562 13. Type of Report and Period Covered Technical

  9. BNL/SNS TECHNICAL NOTE R. Witkover

    E-Print Network [OSTI]

    BNL/SNS TECHNICAL NOTE NO. 049 R. Witkover September 23, 1998 ALTERNATING GRADIENT SYNCHROTRON-In-Gap" Monitor for the Spallation Neutron Source #12;SNS Technical Note Considerations in Designing a "Beam of approximately 550 nsec. With a design intensity of 1014 per pulse, un-controlled losses must be kept to a level

  10. Technical Report Documentation Page 1. Report No.

    E-Print Network [OSTI]

    Texas at Austin, University of

    Technical Report Documentation Page 1. Report No. FHWA/TX-05/0-1778-3 2. Government Accession No. 3, and others. A number of reports, tables, and queries have been prepared and documented herein showing example. This document is available to the public through the National Technical Information Service, Springfield

  11. Technical Documentation and Verification for the

    E-Print Network [OSTI]

    PNNL-15202 Technical Documentation and Verification for the Buildings Module in the Visual Sample://www.ntis.gov/ordering.htm This document was printed on recycled paper. (9/2003) #12;PNNL-15202 Technical Documentation and Verification ...................................................................... 1 2.0 Documentation of Statistical Methods and Computations

  12. Technical Report Documentation Page 1. Report No.

    E-Print Network [OSTI]

    Texas at Austin, University of

    Technical Report Documentation Page 1. Report No. FHWA/TX-05/0-1778-6 2. Government Accession No. 3 summarizes the tasks conducted under TxDOT Project 0-1778 "TxDOT Rigid Pavement Database." This document report is the final technical document prepared for the project. Additional information is provided

  13. Technical Report Documentation Page 1. Report No.

    E-Print Network [OSTI]

    Texas at Austin, University of

    Technical Report Documentation Page 1. Report No. FHWA/TX-04/0-4266-2 2. Government Accession No. 3 significant changes in traffic operation and safety. A review of the design standard documents shows Statement No restrictions. This document is available to the public through the National Technical

  14. Technical Report Documentation Page 1. Report No.

    E-Print Network [OSTI]

    Texas at Austin, University of

    Technical Report Documentation Page 1. Report No. FHWA/TX-10/0-5517-1 2. Government Accession No. 3 for a series of tire bale case histories. The following document outlines all the work conducted as part Statement No restrictions. This document is available to the public through the National Technical

  15. Technical Report Documentation Page 1. Report No.

    E-Print Network [OSTI]

    Texas at Austin, University of

    Technical Report Documentation Page 1. Report No. FHWA/TX-04/0-1405-7 2. Government Accession No. 3 researchers, after an extensive literature review. This report documents the final evaluation of the long No restrictions. This document is available to the public through the National Technical Information Service

  16. Technical Report Documentation Page 1. Report No.

    E-Print Network [OSTI]

    Texas at Austin, University of

    Technical Report Documentation Page 1. Report No. FHWA/TX-04/5-1873-01-1 2. Government Accession No to improve safety and facilitate traffic flow. Finally, they documented these design considerations. This document is available to the public through the National Technical Information Service, Springfield

  17. Technical Report Documentation Page 1. Report No.

    E-Print Network [OSTI]

    Texas at Austin, University of

    Technical Report Documentation Page 1. Report No. FHWA/TX-10/0-6044-1 2. Government Accession No. 3 the researchers' understanding of the general T&R approach used by the industry, (c) documents the research No restrictions. This document is available to the public through the National Technical Information Service

  18. TWRS privatization process technical baseline

    SciTech Connect (OSTI)

    Orme, R.M.

    1996-09-13T23:59:59.000Z

    The U.S. Department of Energy (DOE) is planning a two-phased program for the remediation of Hanford tank waste. Phase 1 is a pilot program to demonstrate the procurement of treatment services. The volume of waste treated during the Phase 1 is a small percentage of the tank waste. During Phase 2, DOE intends to procure treatment services for the balance of the waste. The TWRS Privatization Process Technical Baseline (PPTB) provides a summary level flowsheet/mass balance of tank waste treatment operations which is consistent with the tank inventory information, waste feed staging studies, and privatization guidelines currently available. The PPTB will be revised periodically as privatized processing concepts are crystallized.

  19. MELCOR technical assessment at SNL

    SciTech Connect (OSTI)

    Kmetyk, L.N.; Tautges, T.J.

    1993-12-01T23:59:59.000Z

    MELCOR is a fully integrated, engineering-level computer code that models the progression of severe accidents in light water reactor (LWR) nuclear power plants, which is being developed at Sandia National Laboratories for the US Nuclear Regulatory Commission (US-NRC). The entire spectrum of severe accident phenomena, including reactor coolant system and containment thermal/hydraulic response, core heatup, degradation and relocation, and fission product release and transport, is treated in MELCOR in a unified framework for both boiling water reactors (PRWs). The MELCOR computer code has been developed to the point that is now being successfully applied in severe accident analyses, particularly in probabilistic risk assessment (PRA) studies. MELCOR was the first of the severe accident analysis code to undergo a formal peer review process. One of the major conclusions of the recent MELCOR Peer Review was the need for a more comprehensive and more systematic program of MELCOR assessment. This report provides a discussion of this technical assessment.

  20. Technical abstracts: Mechanical engineering, 1990

    SciTech Connect (OSTI)

    Broesius, J.Y. (comp.)

    1991-03-01T23:59:59.000Z

    This document is a compilation of the published, unclassified abstracts produced by mechanical engineers at Lawrence Livermore National Laboratory (LLNL) during the calendar year 1990. Many abstracts summarize work completed and published in report form. These are UCRL-JC series documents, which include the full text of articles to be published in journals and of papers to be presented at meetings, and UCID reports, which are informal documents. Not all UCIDs contain abstracts: short summaries were generated when abstracts were not included. Technical Abstracts also provides descriptions of those documents assigned to the UCRL-MI (miscellaneous) category. These are generally viewgraphs or photographs presented at meetings. An author index is provided at the back of this volume for cross referencing.

  1. Technical Appendix for Development for Modified Streamflows 1928-1989 : Columbia River & Coastal Basin.

    SciTech Connect (OSTI)

    United States. Bonneville Power Administration; A.G. Crook Company

    1993-06-01T23:59:59.000Z

    The report ``Adjusted Streamflow and Storage 1928-1989`` contains listings of historical flows for the sites in the Columbia River and Coastal Basins. This section of the Technical Appendix provides for the site specific procedures used to determine those historical flows. The study purpose, authority, and definitions are given in the main report. The purpose of this section of the Technical Appendix is to document the computational procedures used at each of the project sites to develop historical flows for the period July 1928--September 1989.

  2. Advanced Small Modular Reactor (SMR) Probabilistic Risk Assessment (PRA) Technical Exchange Meeting

    SciTech Connect (OSTI)

    Curtis Smith

    2013-09-01T23:59:59.000Z

    During FY13, the INL developed an advanced SMR PRA framework which has been described in the report Small Modular Reactor (SMR) Probabilistic Risk Assessment (PRA) Detailed Technical Framework Specification, INL/EXT-13-28974 (April 2013). In this framework, the various areas are considered: Probabilistic models to provide information specific to advanced SMRs Representation of specific SMR design issues such as having co-located modules and passive safety features Use of modern open-source and readily available analysis methods Internal and external events resulting in impacts to safety All-hazards considerations Methods to support the identification of design vulnerabilities Mechanistic and probabilistic data needs to support modeling and tools In order to describe this framework more fully and obtain feedback on the proposed approaches, the INL hosted a technical exchange meeting during August 2013. This report describes the outcomes of that meeting.

  3. US DRIVE Advanced Combustion and Emission Control Technical Team...

    Energy Savers [EERE]

    Advanced Combustion and Emission Control Technical Team Roadmap US DRIVE Advanced Combustion and Emission Control Technical Team Roadmap The ACEC focuses on advanced engine and...

  4. annual technical meeting: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Water Resources Research Institute Annual Technical Report FY 2012 New Jersey Water 322 Kansas Water Resources Research Institute Annual Technical Report Geosciences Websites...

  5. annual meeting technical: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Water Resources Research Institute Annual Technical Report FY 2012 New Jersey Water 322 Kansas Water Resources Research Institute Annual Technical Report Geosciences Websites...

  6. annual international technical: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Water Resources Research Institute Annual Technical Report FY 2012 New Jersey Water 286 Kansas Water Resources Research Institute Annual Technical Report Geosciences Websites...

  7. Net Zero Waste - Tools and Technical Support ...and other observations...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Net Zero Waste - Tools and Technical Support ...and other observations Net Zero Waste - Tools and Technical Support ...and other observations Presentation at Waste-to-Energy using...

  8. US DRIVE Electrochemical Energy Storage Technical Team Roadmap...

    Office of Environmental Management (EM)

    Electrochemical Energy Storage Technical Team Roadmap US DRIVE Electrochemical Energy Storage Technical Team Roadmap This U.S. DRIVE electrochemical energy storage roadmap...

  9. Sources of Technical Variability in Quantitative LC-MS Proteomics...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Sources of Technical Variability in Quantitative LC-MS Proteomics: Human Brain Tissue Sample Analysis. Sources of Technical Variability in Quantitative LC-MS Proteomics: Human...

  10. Building America Analysis Methods and Tools Standing Technical...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Building America Analysis Methods and Tools Standing Technical Committee Presentation Building America Analysis Methods and Tools Standing Technical Committee Presentation This...

  11. actinide halides technical: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    University, Department of Engineering, Technical Report 97-25, December 1997. Based Pont, Michael J. 276 CERTIFICATE PROGRAM in TECHNICAL WRITING Biology and Medicine Websites...

  12. Application of Engineering and Technical Requirements for DOE...

    Office of Environmental Management (EM)

    Engineering and Technical Requirements for DOE Nuclear Facilities Standard Review Plan (SRP) Application of Engineering and Technical Requirements for DOE Nuclear Facilities...

  13. Preliminary Technical Risk Analysis for the Geothermal Technologies...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Preliminary Technical Risk Analysis for the Geothermal Technologies Program Preliminary Technical Risk Analysis for the Geothermal Technologies Program This report explains the...

  14. Enforcement Letter, Babcock & Wilcox Technical Services Y-12...

    Energy Savers [EERE]

    Enforcement Letter, Babcock & Wilcox Technical Services Y-12, LLC - July 10, 2009 Enforcement Letter, Babcock & Wilcox Technical Services Y-12, LLC - July 10, 2009 July 10, 2009...

  15. NSRD-2015-TD01, Technical Report for Calculations of Atmospheric...

    Office of Environmental Management (EM)

    NSRD-2015-TD01, Technical Report for Calculations of Atmospheric Dispersion at Onsite Locations for DOE Nuclear Facilities NSRD-2015-TD01, Technical Report for Calculations of...

  16. WORKSHOP REPORT:Light-Duty Vehicles Technical Requirements and...

    Energy Savers [EERE]

    Light-Duty Vehicles Technical Requirements and Gaps for Lightweight and Propulsion Materials WORKSHOP REPORT:Light-Duty Vehicles Technical Requirements and Gaps for Lightweight and...

  17. WORKSHOP REPORT: Trucks and Heavy-Duty Vehicles Technical Requirements...

    Energy Savers [EERE]

    Heavy-Duty Vehicles Technical Requirements and Gaps for Lightweight and Propulsion Materials WORKSHOP REPORT: Trucks and Heavy-Duty Vehicles Technical Requirements and Gaps for...

  18. 2013 Geothermal Technologies Office Peer Review Technical Report...

    Energy Savers [EERE]

    2013 Geothermal Technologies Office Peer Review Technical Report 2013 Geothermal Technologies Office Peer Review Technical Report March 5, 2014 - 12:00am Addthis Foro Energy, Inc....

  19. Explanations of FreedomCAR/DOE Hydrogen Storage Technical Targets...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Explanations of FreedomCARDOE Hydrogen Storage Technical Targets Explanations of FreedomCARDOE Hydrogen Storage Technical Targets Summary of FreedomCAR Targets and Basis for...

  20. STEP Energy Coach and Technical Consultant Job Descriptions ...

    Energy Savers [EERE]

    Consultant Job Descriptions.pdf More Documents & Publications Technical Consultant RFP Tool Kit Framework: Small Town University Energy Program (STEP) Technical Consultant...

  1. assessment grant technical: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    rockfish management and conservation in the northeast Pacific 24 Technical Instrument Report CDBS 2009-01 Assessment and Delivery of Physics Websites Summary: Technical Instrument...

  2. Effective Community-Wide Policy Technical Assistance: The NREL...

    Open Energy Info (EERE)

    Wide Policy Technical Assistance: The NRELDOE Approach Jump to: navigation, search Tool Summary LAUNCH TOOL Name: Effective Community-Wide Policy Technical Assistance: The NREL...

  3. 2011 Residential Energy Efficiency Technical Update Meeting Summary...

    Energy Savers [EERE]

    2011 Residential Energy Efficiency Technical Update Meeting Summary Report: Denver, Colorado - August 9-11, 2011 2011 Residential Energy Efficiency Technical Update Meeting Summary...

  4. Automated Home Energy Management (AHEM) Standing Technical Committee...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Home Energy Management (AHEM) Standing Technical Committee Strategic Plan - February 2012 Automated Home Energy Management (AHEM) Standing Technical Committee Strategic Plan -...

  5. Energy Department Announces New Technical Assistance for Tribal...

    Office of Environmental Management (EM)

    Energy Department Announces New Technical Assistance for Tribal Clean Energy Projects Energy Department Announces New Technical Assistance for Tribal Clean Energy Projects May 20,...

  6. Africa - Technical Potential of Solar Energy to Address Energy...

    Open Energy Info (EERE)

    Africa - Technical Potential of Solar Energy to Address Energy Poverty and Avoid GHG Emissions Jump to: navigation, search Tool Summary LAUNCH TOOL Name: Technical Potential of...

  7. FreedomCAR and Fuel Partnership 2004 Highlights of Technical...

    Energy Savers [EERE]

    4 Highlights of Technical Accomplishments FreedomCAR and Fuel Partnership 2004 Highlights of Technical Accomplishments Report containing brief summaries of key accomplishments of...

  8. FAQS Gap Analysis Qualification Card - Senior Technical Safety...

    Office of Environmental Management (EM)

    Gap Analysis Qualification Card - Senior Technical Safety Manager FAQS Gap Analysis Qualification Card - Senior Technical Safety Manager Functional Area Qualification Standard Gap...

  9. FAQS Job Task Analyses - Safeguards and Security General Technical...

    Broader source: Energy.gov (indexed) [DOE]

    Base More Documents & Publications FAQS Qualification Card - Safeguards and Security General Technical Base FAQS Job Task Analyses - General Technical Base FAQS Qualification Card...

  10. Recent Research to Address Technical Barriers to Increased Use...

    Broader source: Energy.gov (indexed) [DOE]

    Recent Research to Address Technical Barriers to Increased Use of Biodiesel Recent Research to Address Technical Barriers to Increased Use of Biodiesel 2005 Diesel Engine Emissions...

  11. Task Order Awarded for Environmental Technical Services | Department...

    Broader source: Energy.gov (indexed) [DOE]

    Project Office Audit Task Order Awarded for Technical and Safety Support Services DOE Issues Request for Quotations for Depleted Uranium Hexafluoride Conversion Technical Services...

  12. Task Order Awarded for Technical and Safety Support Services...

    Broader source: Energy.gov (indexed) [DOE]

    Order Awarded for Environmental Technical Services DOE Issues Request for Quotations for Depleted Uranium Hexafluoride Conversion Technical Services DOE Awards Small Business...

  13. aging final technical: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    abundance Oakley, Jeremy 32 Technical Brief CiteSeer Summary: ii iiiFOREWARD The Depleted Uranium Technical Brief is designed to convey available information and knowledge about...

  14. artery origin technical: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    arteries Atalar, Ergin 19 Technical Brief CiteSeer Summary: ii iiiFOREWARD The Depleted Uranium Technical Brief is designed to convey available information and knowledge about...

  15. Technical Assessment of Compressed Hydrogen Storage Tank Systems...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Compressed Hydrogen Storage Tank Systems for Automotive Applications Technical Assessment of Compressed Hydrogen Storage Tank Systems for Automotive Applications Technical report...

  16. Hydrogen and Fuel Cell Technical Advisory Committee Biennial...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Hydrogen and Fuel Cell Technical Advisory Committee Biennial Report to the Secretary of Energy Hydrogen and Fuel Cell Technical Advisory Committee Biennial Report to the Secretary...

  17. Department of Energy Technical Support Document National Environmental...

    Broader source: Energy.gov (indexed) [DOE]

    This Technical Support Document supplements the Department of Energy's (DOE's) Notice of Proposed Rulemaking. In this Technical Support Document, the Department of Energy presents...

  18. Specification No. 203-HJT-9004 R0 Specification for the

    E-Print Network [OSTI]

    McDonald, Kirk

    Specification No. 203-HJT-9004 R0 Specification for the MERIT Mercury-Jet Experiment Titanium TITANIUM TARGET MODULE COMPONENTS Prepared by: V.B. Graves (Oak Ridge National Laboratory) P. T. Spampinato.S. DEPARTMENT OF ENERGY April 10, 2006 #12;Specification for Ti Alloy Components MERIT High Power Mercury

  19. General Vehicle Performance Specifications for the UPRM AUV Vehicle Specifications

    E-Print Network [OSTI]

    Gilbes, Fernando

    General Vehicle Performance Specifications for the UPRM AUV Vehicle Specifications Vehicle Characteristics Specification Maximum Depth 700m with 1.5 safety factor Vehicle power 2kWHr Li Ion Rechargeable Transducer 700m rated Paroscientific Depth Sensor will be integrated into the vehicle navigation stream

  20. Specifications are subject to change without notice. 29 For technical assistance call the Trimmer

    E-Print Network [OSTI]

    Berns, Hans-Gerd

    Stops..................Wiper idles Terminals ........................Solderable pins Weight diagram, date code, manufacturer's model number and style Wiper ..............................Set at CW Adjustment Tool ..............................H-90 1 3 CW CLOCKWISE CCW 2 WIPER 1.52 (.060) 3 2 1 BOTTOM VIEW

  1. TECHNICAL ADVANCE A simple and reliable assay for detecting specific nucleotide

    E-Print Network [OSTI]

    Deng, Xing-Wang

    -film biosensor chips to detect unique transgenes in genetically modified (GM) crops and SNP markers in model-processing sectors often need to detect genetically modified (GM) crops or microbial pathogens in plant product

  2. Administrative Record References: Quarry Residuals Administrative Record Technical Site-Specific References.

    Office of Legacy Management (LM)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742EnergyOn AprilA group currentBradleyTableSelling Corp -KWatertown Arsenal'.I Y.it !D;rC. 1.' :

  3. TIDAL ENERGY SITE RESOURCE ASSESSMENT: TECHNICAL SPECIFICATIONS, BEST PRACTICES AND CASE STUDIES

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645U.S. DOE Office of ScienceandMesa del SolStrengthening a solidSynthesis of 2D Alloys & Heterostructures |TIDAL ENERGY

  4. PROGRAMME SPECIFICATION POSTGRADUATE PROGRAMMES Programme name Renewable Energy and Power Systems Management

    E-Print Network [OSTI]

    Weyde, Tillman

    and understanding: Understand and evaluate the technical aspects and challenges of alternative modes of energy1 PROGRAMME SPECIFICATION ­ POSTGRADUATE PROGRAMMES KEY FACTS Programme name Renewable Energy or equivalent School of Engineering and Mathematical Sciences Programme code PSPSEM Type of study Full time

  5. On the Design of an Interactive, Patient-Specific Surgical Simulator for Mitral Valve Repair

    E-Print Network [OSTI]

    On the Design of an Interactive, Patient-Specific Surgical Simulator for Mitral Valve Repair Neil A repair of the mitral valve is a difficult procedure that is often avoided in favor of less effective valve replacement because of the associated technical challenges facing non-expert surgeons

  6. Technical basis for dose reconstruction

    SciTech Connect (OSTI)

    Anspaugh, L.R.

    1996-01-31T23:59:59.000Z

    The purpose of this paper is to consider two general topics: technical considerations of why dose-reconstruction studies should or should not be performed and methods of dose reconstruction. The first topic is of general and growing interest as the number of dose-reconstruction studies increases, and one asks the question whether it is necessary to perform a dose reconstruction for virtually every site at which, for example, the Department of Energy (DOE) has operated a nuclear-related facility. And there is the broader question of how one might logically draw the line at performing or not performing dose-reconstruction (radiological and chemical) studies for virtually every industrial complex in the entire country. The second question is also of general interest. There is no single correct way to perform a dose-reconstruction study, and it is important not to follow blindly a single method to the point that cheaper, faster, more accurate, and more transparent methods might not be developed and applied.

  7. 1990 Resource Program : Technical Report.

    SciTech Connect (OSTI)

    United States. Bonneville Power Administration.

    1990-07-01T23:59:59.000Z

    This Technical Report is a detailed presentation of the actions Bonneville Power Administration (BPA) will take to develop new resources to meet the power requirements of its customers. The primary focus of this report is on what BPA will do in Fiscal Years (FY's) 1992 and 1993. However, much care has been taken to define near-term actions aimed at meeting BPA's long-term needs. An aggressive, steadily increasing conservation program forms the foundation of the 1990 Resource Program and resource acquisitions for FY's 1992 and 1993. BPA's commitment to a steady ramp-up of the conservation program is key to achieving the least-cost approach to resource development, and to making the conservation resource deliverable in the long run. By itself, conservation can meet much of the likely range of load growth that BPA faces. A diverse mix of generation resources in small increments is the second cornerstone of the 1990 Resource Program. These generation resources can meet the rest of the likely range of BPA resource needs. Finally, a Resource Contingency Plan prepares BPA to reliably meet load in the event that load growth exceeds the likely range. 14 figs., 27 tabs.

  8. Technical University of Denmark rsted DTU Automation

    E-Print Network [OSTI]

    Technical University of Denmark �rsted · DTU Automation Project: SICAM - SIngle Conversion stage based SICAM using an LC-network Petar Ljusev, MSc., Ph.D. student, �rsted · DTU Automation e-mail: pl

  9. Technical University of Denmark rsted DTU Automation

    E-Print Network [OSTI]

    Technical University of Denmark �rsted · DTU Automation Project: SICAM - SIngle Conversion stage, �rsted · DTU Automation e-mail: pl@oersted.dtu.dk Abstract In this report an isolated PWM DC-AC SICAM

  10. RISK ASSESSMENT TECHNICAL EXPERT WORKING GROUP

    Broader source: Energy.gov [DOE]

    The Risk Assessment Technical Expert Working Group (RWG) is established to assist the Department of Energy (DOE) with the appropriate and effective use of quantitative risk assessment in nuclear...

  11. Energy Technical Assistance: Industrial Processes Program

    E-Print Network [OSTI]

    McClure, J. D.

    1980-01-01T23:59:59.000Z

    The Energy Technical Assistance Division of Texas Engineering Extension Service (TEEX) has implemented an energy conservation program to assist small industry in using energy more efficiently. This full time service, an outgrowth of the Texas A...

  12. Financial and Technical Resources The HUD Perspective 

    E-Print Network [OSTI]

    Jensen, J.

    2011-01-01T23:59:59.000Z

    Financial and Technical Resources The HUD Perspective U.S. Department of Housing and Urban Development Jerry Jensen, HUD Fort Worth Regional Office CATEE Conference November 9, 2011 Partnership for Sustainable Communities: Livability...

  13. Water Resources Research Institute Annual Technical Report

    E-Print Network [OSTI]

    Water Resources Research Institute Annual Technical Report FY 1999 Introduction ABSTRACT The FY 1999 Oregon Water Resources Research Institute (OWRRI) program included four research projects funded Coastal Lakes: Water Quality Status and Management Implications Based on Nutrient Loading OWRRI sponsored

  14. Hydraulic and Habitat Suitability Analyses Technical Memorandum

    E-Print Network [OSTI]

    Appendix D Hydraulic and Habitat Suitability Analyses Technical Memorandum #12;COPYRIGHT DECEMBER Series 2 and Pond Series 3 Hydraulic and Habitat Suitability Analyses Prepared for Bureau of Reclamation HILL, INC. III Hydraulic and Habitat Suitability Analyses

  15. Fifth technical contractors' conference on peat

    SciTech Connect (OSTI)

    Not Available

    1982-01-01T23:59:59.000Z

    The Fifth Technical Contractors' Conference on Peat was held April 28 to 29, 1982, at Bethesda, Maryland. Thirty papers have been entered into EDB and ERA; two had been entered previously from other sources. (LTN)

  16. TR-017 Ecology March 2002 Technical Report

    E-Print Network [OSTI]

    TR-017 Ecology March 2002 Technical Report Forest Research Vancouver Forest Region 2100 Labieux Region Coarse Woody Debris Working Group Research Disciplines: Ecology ~ Geology ~ Geomorphology Research Section, Vancouver Forest Region, BCMOF Research Disciplines: Ecology ~ Geology ~ Geomorphology

  17. Texas Water Resources Institute Annual Technical Report

    E-Print Network [OSTI]

    Texas Water Resources Institute Annual Technical Report FY 2003 Introduction The Mission of the Texas Water Resources Institute is to: (1) Provide leadership for Experiment Station and Extension research and education water programs statewide, coordinating with scientists, specialists, county agents

  18. Arkansas Water Resources Center Annual Technical Report

    E-Print Network [OSTI]

    and heavy metals to surface runoff following storm events. Evaluating runoff water quality response, innovative domestic wastewater disposal systems, ground water modeling and landuse mapping, erosionArkansas Water Resources Center Annual Technical Report FY 2008 Arkansas Water Resources Center

  19. Water Research Institute Annual Technical Report

    E-Print Network [OSTI]

    : Ground-water Flow and Transport Focus Category: Non Point Pollution, Surface Water, Toxic Substances Descriptors: Benthos, Bioindicators, Biomonitoring, Ecosystems, Heavy metals, Insects, Land use, PollutantsWater Research Institute Annual Technical Report FY 2001 Introduction Introduction - Research

  20. Contributions to Metric Number Technical Report

    E-Print Network [OSTI]

    Dent, Alexander W.

    Contributions to Metric Number Theory Paul Rowe Technical Report RHUL­MA­2002­2 5 December 2002, Professor Glyn Harman, for sug- gestions of problems to attempt, helpful advice on methods and help

  1. Utility Variable Generation Integration Group Fall Technical...

    Broader source: Energy.gov (indexed) [DOE]

    15, 2014 9:00AM CDT to October 17, 2014 3:00PM CDT The Utility Variable Generation Integration Group (UVIG) Fall Technical Workshop in San Antonio, Texas will provide attendees...

  2. Technical Report Documentation Page 1. Report No.

    E-Print Network [OSTI]

    Texas at Austin, University of

    to evaluate the technical suitability of AC overlays on CRCP. These criteria are, namely, a profile criterion, based on the remaining life concept and on the formulation of a dynamic load factor; a condition survey

  3. Fuel Pathway Integration Technical Team Roadmap

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Fuel Pathway Integration Technical Team Roadmap June 2013 This roadmap is a document of the U.S. DRIVE Partnership. U.S. DRIVE (Driving Research and Innovation for Vehicle...

  4. Technical basis document for natural event hazards

    SciTech Connect (OSTI)

    CARSON, D.M.

    2003-08-28T23:59:59.000Z

    This technical basis document was developed to support the documented safety analysis (DSA) and describes the risk binning process and the technical basis for assigning risk bins for natural event hazard (NEH)-initiated accidents. The purpose of the risk binning process is to determine the need for safety-significant structures, systems, and components (SSC) and technical safety requirement (TSR)-level controls for a given representative accident or represented hazardous conditions based on an evaluation of the frequency and consequence. Note that the risk binning process is not applied to facility workers, because all facility worker hazardous conditions are considered for safety-significant SSCs and/or TSR-level controls This report documents the technical basis for assigning risk bins for Natural Event Hazards Representative Accident and associated represented hazardous conditions.

  5. Nebraska Water Resources Center Annual Technical Report

    E-Print Network [OSTI]

    : Groundwater, Models, Water Use Descriptors: Aquifer parameters, conjuntive use, groundwater modeling, surface-groundwater modeling, Surface- groundwater Relationships, Well hydraulics Problem and research objectives: ProblemNebraska Water Resources Center Annual Technical Report FY 2000 Introduction Welcome

  6. Energy Technical Assistance: Industrial Processes Program 

    E-Print Network [OSTI]

    McClure, J. D.

    1980-01-01T23:59:59.000Z

    The Energy Technical Assistance Division of Texas Engineering Extension Service (TEEX) has implemented an energy conservation program to assist small industry in using energy more efficiently. This full time service, an outgrowth of the Texas A...

  7. Technical Report Documentation Page 1. Report No.

    E-Print Network [OSTI]

    Texas at Austin, University of

    Technical Report Documentation Page 1. Report No. FHWA/TX-02/1884-2 2. Government Accession No. 3, paratransit systems 18. Distribution Statement No restrictions. This document is available to the public

  8. Technical Report Documentation Page 1. Report No.

    E-Print Network [OSTI]

    Texas at Austin, University of

    Technical Report Documentation Page 1. Report No. FHWA/TX-09/0-5367-1 2. Government Accession No. 3, deck, slab, shear, fatigue 18. Distribution Statement No restrictions. This document is available

  9. Technical Report Documentation Page 1. Report No.

    E-Print Network [OSTI]

    Texas at Austin, University of

    Technical Report Documentation Page 1. Report No. FHWA/TX-03/4382-1 2. Government Accession No. 3, concrete pavement, sensitivity, fatigue, distress 18. Distribution Statement No restrictions. This document

  10. Technical Report Documentation Page 1. Report No.

    E-Print Network [OSTI]

    Zornberg, Jorge G.

    Technical Report Documentation Page 1. Report No. FHWA/TX-10/5-4829-01-1 2. Government Accession No, stiffness 18. Distribution Statement No restrictions. This document is available to the public through

  11. Technical Report Documentation Page 1. Report No.

    E-Print Network [OSTI]

    Texas at Austin, University of

    Technical Report Documentation Page 1. Report No. 1747-3 2. Government Accession No. 3. Recipient, Information Technology 18. Distribution Statement No restrictions. This document is available to the public

  12. Technical Report Documentation Page 1. Report No.

    E-Print Network [OSTI]

    Zornberg, Jorge G.

    Technical Report Documentation Page 1. Report No. FHWA/TX-10/5-5517-01-1 2. Government Accession No, field monitoring 18. Distribution Statement No restrictions. This document is available to the public

  13. Technical Report Documentation Page 1. Report No.

    E-Print Network [OSTI]

    Texas at Austin, University of

    Technical Report Documentation Page 1. Report No. FHWA/TX-0-2122-1 2. Government Accession No. 3, regulations, vehicle characteristics 18. Distribution Statement No restrictions. This document is available

  14. Technical Report Documentation Page 1. Report No.

    E-Print Network [OSTI]

    Texas at Austin, University of

    Technical Report Documentation Page 1. Report No. FWHA/TX-05/0-1774-3 2. Government Accession No. 3, rehabilitation, encapsulation 18. Distribution Statement No restrictions. This document is available

  15. Technical Report Documentation Page 1. Report No.

    E-Print Network [OSTI]

    Texas at Austin, University of

    Technical Report Documentation Page 1. Report No. FHWA/TX-09/0-5197-4 2. Government Accession No. 3 consolidating concrete, microcracking 18. Distribution Statement No restrictions. This document is available

  16. Technical Report Documentation Page 1. Report No.

    E-Print Network [OSTI]

    Texas at Austin, University of

    Technical Report Documentation Page 1. Report No. FHWA/TX-03/1892-1 2. Government Accession No. 3, nondestructive testing 18. Distribution Statement No restrictions. This document is available to the public

  17. Technical Report Documentation Page 1. Report No.

    E-Print Network [OSTI]

    Texas at Austin, University of

    Technical Report Documentation Page 1. Report No. FHWA/TX-05/9-580/589-1 2. Government Accession No resistance, creep, shrinkage 18. Distribution Statement No restrictions. This document is available

  18. Technical Report Documentation Page 1. Report No.

    E-Print Network [OSTI]

    Texas at Austin, University of

    Technical Report Documentation Page 1. Report No. FHWA/TX-08/0-4562-2 2. Government Accession No. 3 concrete 18. Distribution Statement No restrictions. This document is available to the public through

  19. Technical Report Documentation Page 1. Report No.

    E-Print Network [OSTI]

    Texas at Austin, University of

    Technical Report Documentation Page 1. Report No. FHWA/TX-04/0-1405-9 2. Government Accession No. 3 joints, reinforcement coatings 18. Distribution Statement No restrictions. This document is available

  20. Technical Report Documentation Page 1. Report No.

    E-Print Network [OSTI]

    Texas at Austin, University of

    Technical Report Documentation Page 1. Report No. FHWA/TX-03/1898-1 2. Government Accession No. 3 after the deck had hardened. 17. Key Words 18. Distribution Statement No restrictions. This document

  1. Technical Report Documentation Page 1. Report No.

    E-Print Network [OSTI]

    Texas at Austin, University of

    Technical Report Documentation Page 1. Report No. FHWA/TX-00/1795-1 2. Government Accession No. 3 strategies 18. Distribution Statement No restrictions. This document is available to the public through

  2. Technical Report Documentation Page 1. Report No.

    E-Print Network [OSTI]

    Texas at Austin, University of

    Technical Report Documentation Page 1. Report No. FHWA/TX-02/1395-2F 2. Government Accession No. 3 Bracing, Brace Forces, Torsional Stiffness 18. Distribution Statement No restrictions. This document

  3. Technical Report Documentation Page 1. Report No.

    E-Print Network [OSTI]

    Texas at Austin, University of

    Technical Report Documentation Page 1. Report No. FHWA/TX-02-1810-2 2. Government Accession No. 3 in Texas 18. Distribution Statement No restrictions. This document is available to the public through

  4. Technical Report Documentation Page 1. Report No.

    E-Print Network [OSTI]

    Texas at Austin, University of

    Technical Report Documentation Page 1. Report No. FHWA/TX-04/5-1291-01-1 2. Government Accession No),PASSER II, GEOPAK, Vehicle Turn Templates 18. Distribution Statement No restrictions. This document

  5. Technical Report Documentation Page 1. Report No.

    E-Print Network [OSTI]

    Texas at Austin, University of

    i Technical Report Documentation Page 1. Report No. FHWA/TX-07 / 0-1774-4 2. Government Accession, encapsulation 18. Distribution Statement No restrictions. This document is available to the public through

  6. Technical Report Documentation Page 1. Report No.

    E-Print Network [OSTI]

    Texas at Austin, University of

    Technical Report Documentation Page 1. Report No. FHWA/TX-10/0-5185-3 2. Government Accession No. 3 Pavement. 18. Distribution Statement No restrictions. This document is available to the public through

  7. Technical Report Documentation Page 1. Report No.

    E-Print Network [OSTI]

    Texas at Austin, University of

    Technical Report Documentation Page 1. Report No. FHWA/TX-02/1852-1 2. Government Accession No. 3 concrete mix design 18. Distribution Statement No restrictions. This document is available to the public

  8. Technical Report Documentation Page 1. Report No.

    E-Print Network [OSTI]

    Texas at Austin, University of

    Technical Report Documentation Page 1. Report No. FHWA/TX-08/5-4958-01-1 2. Government Accession No lens 18. Distribution Statement No restrictions. This document is available to the public through

  9. Technical Report Documentation Page 1. Report No.

    E-Print Network [OSTI]

    Texas at Austin, University of

    Technical Report Documentation Page 1. Report No. FHWA/TX-03-1810-3 2. Government Accession No. 3, Highway user taxes, Highway finance 18. Distribution Statement No restrictions. This document is available

  10. Technical Report Documentation Page 1. Report No.

    E-Print Network [OSTI]

    Zornberg, Jorge G.

    Technical Report Documentation Page 1. Report No. FHWA/TX-07/0-5202-3 2. Government Accession No. 3 Shale, Paris Clay, Beaumont Clay. 18. Distribution Statement No restrictions. This document is available

  11. Technical Report Documentation Page 1. Report No.

    E-Print Network [OSTI]

    Texas at Austin, University of

    Technical Report Documentation Page 1. Report No. FHWA/TX-07/0-4080-8 2. Government Accession No. 3 frameworks, econometric models, empirical results 18. Distribution Statement No restrictions. This document

  12. Technical Report Documentation Page 1. Report No.

    E-Print Network [OSTI]

    Texas at Austin, University of

    Technical Report Documentation Page 1. Report No. 0-4080-1 2. Government Accession No. 3. Recipient modeling 18. Distribution Statement No restrictions. This document is available to the public through

  13. Technical Report Documentation Page 1. Report No.

    E-Print Network [OSTI]

    Texas at Austin, University of

    Technical Report Documentation Page 1. Report No. FHWA/TX-7-2957-2 2. Government Accession No. 3/pavement interaction, pavement noise, noise level. 18. Distribution Statement No restrictions. This document

  14. TESLA Technical Design Report Executive Summary

    E-Print Network [OSTI]

    TESLA Technical Design Report PART I Executive Summary March 2001 Editors: F.Richard, J.R.Schneider, D.Trines, A.Wagner #12;#12;Dedicated to the memory of Bjørn H. Wiik (1937-1999) #12;#12;TESLA ­ A Summary This report describes the scientific aims and potential as well as the technical de- sign of TESLA

  15. MCO loading and cask loadout technical manual

    SciTech Connect (OSTI)

    PRAGA, A.N.

    1998-10-01T23:59:59.000Z

    A compilation of the technical basis for loading a multi-canister overpack (MCO) with spent nuclear fuel and then placing the MCO into a cask for shipment to the Cold Vacuum Drying Facility. The technical basis includes a description of the process, process technology that forms the basis for loading alternatives, process control considerations, safety considerations, equipment description, and a brief facility structure description.

  16. annual technical symposium: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Summary: Report Date: Mar 31, 2003 Semi-Annual Technical Progress Report PREFERRED WATERFLOOD MANAGEMENT...3...

  17. analysis technical progress: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Summary: Report Date: Mar 31, 2003 Semi-Annual Technical Progress Report PREFERRED WATERFLOOD MANAGEMENT...3...

  18. annual technical progress: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Summary: Report Date: Mar 31, 2003 Semi-Annual Technical Progress Report PREFERRED WATERFLOOD MANAGEMENT...3...

  19. annual progress technical: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Summary: Report Date: Mar 31, 2003 Semi-Annual Technical Progress Report PREFERRED WATERFLOOD MANAGEMENT...3...

  20. activity technical progress: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Summary: Report Date: Mar 31, 2003 Semi-Annual Technical Progress Report PREFERRED WATERFLOOD MANAGEMENT...3...

  1. alcohols technical progress: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Summary: Report Date: Mar 31, 2003 Semi-Annual Technical Progress Report PREFERRED WATERFLOOD MANAGEMENT...3...

  2. Evaluation of the Technical Basis for Extended Dry Storage and

    E-Print Network [OSTI]

    -- Executive Summary U.S. Nuclear Waste Technical Review Board December 2010 #12;U.S.U.S. Nuclear Waste Technical Review Board Authors This report was prepared for the U.S. Nuclear Waste Technical Review Board.NWTRB.GOV ii #12;Extended Dry Storage and Transportation of Used Nuclear Fuel U.S. Nuclear Waste Technical

  3. DOE Technical Standards Program Procedures, 2009, DOE-TSPP-6

    Broader source: Energy.gov (indexed) [DOE]

    2.1.6 Coordination of Technical Qualification Standards and Information Architecture Standards ......

  4. DOE-TSPP-06; Coordination of DOE Technical Standard

    Broader source: Energy.gov (indexed) [DOE]

    5 2.1.6 Coordination of Technical Qualification Standards and Information Architecture Standards......

  5. Kentucky Water Resources Research Institute Annual Technical Report

    E-Print Network [OSTI]

    support for the Paducah Gaseous Diffusion Plant (CHS), 3) Technical Support for Environmental Construction

  6. Web-Based Method to Generate Specific Energy Consumption Data for the Evaluation and Optimization of Building Operation

    E-Print Network [OSTI]

    Wagner, A.; Wambsgan, M.; Froehlich, S.

    2004-01-01T23:59:59.000Z

    about energy consumptionand specific data especially in large building stocks?user complaints and energy consumption arerarely considered in building operation?reduction of energy consumption and operation costsas well as ensuring a high work space... consumption specific heating energy consumption buildings with additional technical usage (control room)without arithmetic mean consumption related to the heated net floor area; data measured one full year: 02-2001 to 02-2002 specific yearly energy...

  7. Technical solutions to nonproliferation challenges

    SciTech Connect (OSTI)

    Satkowiak, Lawrence [Director, Nonproliferation, Safeguards and Security Programs, Oak Ridge National Laboratory, Oak Ridge, Tennessee (United States)

    2014-05-09T23:59:59.000Z

    The threat of nuclear terrorism is real and poses a significant challenge to both U.S. and global security. For terrorists, the challenge is not so much the actual design of an improvised nuclear device (IND) but more the acquisition of the special nuclear material (SNM), either highly enriched uranium (HEU) or plutonium, to make the fission weapon. This paper provides two examples of technical solutions that were developed in support of the nonproliferation objective of reducing the opportunity for acquisition of HEU. The first example reviews technologies used to monitor centrifuge enrichment plants to determine if there is any diversion of uranium materials or misuse of facilities to produce undeclared product. The discussion begins with a brief overview of the basics of uranium processing and enrichment. The role of the International Atomic Energy Agency (IAEA), its safeguard objectives and how the technology evolved to meet those objectives will be described. The second example focuses on technologies developed and deployed to monitor the blend down of 500 metric tons of HEU from Russia's dismantled nuclear weapons to reactor fuel or low enriched uranium (LEU) under the U.S.-Russia HEU Purchase Agreement. This reactor fuel was then purchased by U.S. fuel fabricators and provided about half the fuel for the domestic power reactors. The Department of Energy established the HEU Transparency Program to provide confidence that weapons usable HEU was being blended down and thus removed from any potential theft scenario. Two measurement technologies, an enrichment meter and a flow monitor, were combined into an automated blend down monitoring system (BDMS) and were deployed to four sites in Russia to provide 24/7 monitoring of the blend down. Data was downloaded and analyzed periodically by inspectors to provide the assurances required.

  8. Environmental effects of dredging. Evaluating environmental effects of dredged material management alternatives - a technical framework. Technical notes

    SciTech Connect (OSTI)

    Palermo, M.R.; Francingues, N.R.; Engler, R.M.

    1993-02-01T23:59:59.000Z

    This Technical Note presents a brief description of a joint U.S. Army Corps of Engineers (USACE) and U.S. Environmental Protection Agency (USEPA) Technical Framework for the identification of environmentally acceptable alternatives for the management of dredged material. This Technical Note replaces the earlier Technical Note EEDPA-06-14, which should be discarded.

  9. Socio-Technical Systems: A Meta-Design Perspective Page 1 of 34 Socio-Technical Systems

    E-Print Network [OSTI]

    Fischer, Gerhard

    Socio-Technical Systems: A Meta-Design Perspective Page 1 of 34 Socio-Technical Systems ­ A Meta of Bochum) thomas.herrmann@rub.de Abstract Meta-design of socio-technical systems is an approach which complies with the need of integrating two different types of structures and processes: technical systems

  10. Renewable Fuel Heating Plant SyStem SpecificationS

    E-Print Network [OSTI]

    Renewable Fuel Heating Plant SyStem SpecificationS Manufacturer: Advanced Recycling Equipment efficiency of natural gas combustion) The facility is designed to meet additional future heating loads, so annual output will increase when the Research Support Facility comes online What it will heat

  11. Specification No. 203-HJT-9004 R1 Specification for the

    E-Print Network [OSTI]

    McDonald, Kirk

    .S. DEPARTMENT OF ENERGY April 10, 2006 #12;Specification for Titanium Components MERIT High Power Mercury Titanium Components August 14, 2006 #12;Specification for Titanium Components MERIT High Power Mercury MODULE TITANIUM COMPONENTS Prepared by: V.B. Graves (Oak Ridge National Laboratory) P. T. Spampinato (Oak

  12. Mesa Top Photovoltaic Array SyStem SpecificationS

    E-Print Network [OSTI]

    Mesa Top Photovoltaic Array SyStem SpecificationS System size: 750 kW (DC, estimated) Characteristics: Single axis tracker photovoltaics, ground mounted Annual output: 1,200 MWh Location: Top of South Table Mountain; NREL Campus; Golden, Colorado Start of operation: Spring 2008 financial terms System

  13. DOCUMENTATION SPECIFIC TASK TRAINING PROGRAM

    E-Print Network [OSTI]

    Illinois at Urbana-Champaign, University of

    DOCUMENTATION APPENDIX SPECIFIC TASK TRAINING PROGRAM Conducted by the ILLINOIS CENTER ............................................................. Coordination of Contract Documents Art.105.05 Appendix Page 14

  14. Pre-Approved1 Chemical Engineering Technical Electives (NOTE: Technical Electives Engineering Electives Bioengineering Electives)2

    E-Print Network [OSTI]

    Dyer, Bill

    EELE 250 Circuits, Devices, and Motors [F,S] 4 EENV 340 Principles of Environmental Engineering [F,S] 3Pre-Approved1 Chemical Engineering Technical Electives (NOTE: Technical Electives Engineering Biochemistry of Macromolecules [F] 3 BIOB 256 Intro Biol: Cells to Organisms [S] 3+1 BIOB 375 General Genetics

  15. Pre-Approved1 Chemical Engineering Technical Electives (NOTE: Technical Electives Engineering Electives Bioengineering Electives)2

    E-Print Network [OSTI]

    Lawrence, Rick L.

    & Design [S] 3 EIND 354 Engr Probability and Statistics I [F] 3 EIND 434 Project and Engineering Management [F] 3 EMAT 252 Materials Science Laboratory [F,S] 1 EMAT 452 Adv. Engineering Materials [on demand] 3Pre-Approved1 Chemical Engineering Technical Electives (NOTE: Technical Electives Engineering

  16. Optics Technical Electives As of Fall 2013, three technical electives are required. Suggested technical elective themes are listed in blue in the first row of

    E-Print Network [OSTI]

    Mahon, Bradford Z.

    Optics Technical Electives As of Fall 2013, three technical in Optics Class Title OPT 204 Sources Lab OPT 223 Quantum Theory of Optics-Mechanics OPT 241 Geometrical Optics OPT 242 Aberrations and Testing OPT 243 Optical

  17. Technical Review of SRS Dose Reconstrruction Methods Used By CDC

    SciTech Connect (OSTI)

    Simpkins, Ali, A

    2005-07-20T23:59:59.000Z

    At the request of the Centers for Disease Control and Prevention (CDC), a subcontractor Advanced Technologies and Laboratories International, Inc.(ATL) issued a draft report estimating offsite dose as a result of Savannah River Site operations for the period 1954-1992 in support of Phase III of the SRS Dose Reconstruction Project. The doses reported by ATL differed than those previously estimated by Savannah River Site SRS dose modelers for a variety of reasons, but primarily because (1) ATL used different source terms, (2) ATL considered trespasser/poacher scenarios and (3) ATL did not consistently use site-specific parameters or correct usage parameters. The receptors with the highest dose from atmospheric and liquid pathways were within about a factor of four greater than dose values previously reported by SRS. A complete set of technical comments have also been included.

  18. Technical Manual for the SAM Physical Trough Model

    SciTech Connect (OSTI)

    Wagner, M. J.; Gilman, P.

    2011-06-01T23:59:59.000Z

    NREL, in conjunction with Sandia National Lab and the U.S Department of Energy, developed the System Advisor Model (SAM) analysis tool for renewable energy system performance and economic analysis. This paper documents the technical background and engineering formulation for one of SAM's two parabolic trough system models in SAM. The Physical Trough model calculates performance relationships based on physical first principles where possible, allowing the modeler to predict electricity production for a wider range of component geometries than is possible in the Empirical Trough model. This document describes the major parabolic trough plant subsystems in detail including the solar field, power block, thermal storage, piping, auxiliary heating, and control systems. This model makes use of both existing subsystem performance modeling approaches, and new approaches developed specifically for SAM.

  19. Hanford Site environmental management specification

    SciTech Connect (OSTI)

    Grygiel, M.L.

    1998-06-10T23:59:59.000Z

    The US Department of Energy, Richland Operations Office (RL) uses this Hanford Site Environmental Management Specification (Specification) to document top-level mission requirements and planning assumptions for the prime contractors involved in Hanford Site cleanup and infrastructure activities under the responsibility of the US Department of Energy, Office of Environmental Management. This Specification describes at a top level the activities, facilities, and infrastructure necessary to accomplish the cleanup of the Hanford Site and assigns this scope to Site contractors and their respective projects. This Specification also references the key National Environmental Policy Act of 1969 (NEPA), Comprehensive Environmental Response, Compensation, and Liability Act of 1980 (CERCLA), and safety documentation necessary to accurately describe the cleanup at a summary level. The information contained in this document reflects RL`s application of values, priorities, and critical success factors expressed by those involved with and affected by the Hanford Site project. The prime contractors and their projects develop complete baselines and work plans to implement this Specification. These lower-level documents and the data that support them, together with this Specification, represent the full set of requirements applicable to the contractors and their projects. Figure 1-1 shows the relationship of this Specification to the other basic Site documents. Similarly, the documents, orders, and laws referenced in this specification represent only the most salient sources of requirements. Current and contractual reference data contain a complete set of source documents.

  20. Technical Assistance Contractor management plan. Revision 1

    SciTech Connect (OSTI)

    NONE

    1995-08-01T23:59:59.000Z

    The Technical Assistance Contractor (TAC) for the Uranium Mill Tailings Remedial Action (UMTRA) Project comprises Jacobs Engineering Group Inc. (JEG) as the prime contractor and three teaming partner subcontractors: Roy F. Weston, Inc. (RFW), AGRA Earth and Environmental, Inc. (AGRA), and Geraghty and Miller, Inc. (G and M). The TAC contract`s scope is to provide technical, analytical, environmental, engineering, design, inspection, and management support services to the US Department of Energy (DOE) for both Surface and Ground Water Projects. The TAC team supports the DOE in completing surface remedial action and initiating ground water remediation work for start-up, characterization, compliance planning, design, construction oversight, and remedial operations. The TAC provides the DOE UMTRA Project Team with a dedicated management, scientific, and technical resource base in Albuquerque, New Mexico, which is supplemented by corporate resources. A carefully developed and maintained staff of technical experts is available to assess, analyze, develop, and execute cost-effective solutions to the demanding technical and institutional problems presented by the UMTRA Project.

  1. Technology status in support of refined technical baseline for the Spent Nuclear Fuel project. Revision 1

    SciTech Connect (OSTI)

    Puigh, R.J.; Toffer, H.; Heard, F.J.; Irvin, J.J.; Cooper, T.D.

    1995-10-20T23:59:59.000Z

    The Spent Nuclear Fuel Project (SNFP) has undertaken technology acquisition activities focused on supporting the technical basis for the removal of the N Reactor fuel from the K Basins to an interim storage facility. The purpose of these technology acquisition activities has been to identify technology issues impacting design or safety approval, to establish the strategy for obtaining the necessary information through either existing project activities, or the assignment of new work. A set of specific path options has been identified for each major action proposed for placing the N Reactor fuel into a ``stabilized`` form for interim storage as part of this refined technical basis. This report summarizes the status of technology information acquisition as it relates to key decisions impacting the selection of specific path options. The following specific categories were chosen to characterize and partition the technology information status: hydride issues and ignition, corrosion, hydrogen generation, drying and conditioning, thermal performance, criticality and materials accountability, canister/fuel particulate behavior, and MCO integrity. This report represents a preliminary assessment of the technology information supporting the SNFP. As our understanding of the N Reactor fuel performance develops the technology information supporting the SNFP will be updated and documented in later revisions to this report. Revision 1 represents the incorporation of peer review comments into the original document. The substantive evolution in our understanding of the technical status for the SNFP (except section 3) since July 1995 have not been incorporated into this revision.

  2. TECHNICAL BASIS DOCUMENT FOR NATURAL EVENT HAZARDS

    SciTech Connect (OSTI)

    KRIPPS, L.J.

    2006-07-31T23:59:59.000Z

    This technical basis document was developed to support the documented safety analysis (DSA) and describes the risk binning process and the technical basis for assigning risk bins for natural event hazard (NEH)-initiated accidents. The purpose of the risk binning process is to determine the need for safety-significant structures, systems, and components (SSC) and technical safety requirement (TSR)-level controls for a given representative accident or represented hazardous conditions based on an evaluation of the frequency and consequence. Note that the risk binning process is not applied to facility workers, because all facility worker hazardous conditions are considered for safety-significant SSCs and/or TSR-level controls.

  3. Technical basis document for natural event hazards

    SciTech Connect (OSTI)

    CARSON, D.M.

    2003-03-20T23:59:59.000Z

    This technical basis document was developed to support the Tank Farms Documented Safety Analysis (DSA), and describes the risk binning process and the technical basis for assigning risk bins for natural event hazards (NEH)-initiated representative accident and associated represented hazardous conditions. The purpose of the risk binning process is to determine the need for safety-significant structures, systems, and components (SSC) and technical safety requirement (TSR)-level controls for a given representative accident or represented hazardous conditions based on an evaluation of the frequency and consequence. Note that the risk binning process is not applied to facility workers, because all facility worker hazardous conditions are considered for safety-significant SSCs and/or TSR-level controls. Determination of the need for safety-class SSCs was performed in accordance with DOE-STD-3009-94, ''Preparation Guide for US Department of Energy Nonreactor Nuclear Facility Documented Safety Analyses'', as described in this report.

  4. 1996 DOE technical standards program workshop: Proceedings

    SciTech Connect (OSTI)

    NONE

    1996-07-01T23:59:59.000Z

    The workshop theme is `The Strategic Standardization Initiative - A Technology Exchange and Global Competitiveness Challenge for DOE.` The workshop goal is to inform the DOE technical standards community of strategic standardization activities taking place in the Department, other Government agencies, standards developing organizations, and industry. Individuals working on technical standards will be challenged to improve cooperation and communications with the involved organizations in response to the initiative. Workshop sessions include presentations by representatives from various Government agencies that focus on coordination among and participation of Government personnel in the voluntary standards process; reports by standards organizations, industry, and DOE representatives on current technology exchange programs; and how the road ahead appears for `information superhighway` standardization. Another session highlights successful standardization case studies selected from several sites across the DOE complex. The workshop concludes with a panel discussion on the goals and objectives of the DOE Technical Standards Program as envisioned by senior DOE management. The annual workshop on technical standards has proven to be an effective medium for communicating information related to standards throughout the DOE community. Technical standards are used to transfer technology and standardize work processes to produce consistent, acceptable results. They provide a practical solution to the Department`s challenge to protect the environment and the health and safety of the public and workers during all facility operations. Through standards, the technologies of industries and governments worldwide are available to DOE. The DOE Technical Standards Program, a Department-wide effort that crosscuts all organizations and disciplines, links the Department to those technologies.

  5. Technical analysis of US Army Weapons Systems and related advanced technologies of military interest. Final report

    SciTech Connect (OSTI)

    NONE

    1991-06-14T23:59:59.000Z

    This report summarizes the activities and accomplishments of an US Army technology security project designed to identify and develop effective policy guidelines for militarily critical technologies in specific Army systems and in broad generic technology areas of military interest, Individual systems analyses are documented in separate Weapons Systems Technical Assessments (WSTAs) and the general generic technology areas are evaluated in the Advanced Technology Assessment Reports (ATARs), However, specific details of these assessments are not addressed here, only recommendations regarding aspects of the defined approach, methodology, and format are provided and discussed.

  6. DOE technical standards list. Department of Energy standards index

    SciTech Connect (OSTI)

    NONE

    1995-08-01T23:59:59.000Z

    This document was prepared for use by personnel involved in the selection and use of DOE technical standards and other Government and non-Government standards. This TSL provides listing of current DOE technical standards, non-Government standards that have been adopted by DOE, other Government documents in which DOE has a recorded interest, and canceled DOE technical standards. Information on new DOE technical standards projects, technical standards released for coordination, recently published DOE technical standards, and activities of non-Government standards bodies that may be of interest to DOE is published monthly in Standards Actions.

  7. NHI Component Technical Readiness Evaluation System

    SciTech Connect (OSTI)

    Steven R. Sherman; Dane F. Wilson; Steven J. Pawel

    2007-09-01T23:59:59.000Z

    A decision process for evaluating the technical readiness or maturity of components (i.e., heat exchangers, chemical reactors, valves, etc.) for use by the U.S. DOE Nuclear Hydrogen Initiative is described. This system is used by the DOE NHI to assess individual components in relation to their readiness for pilot-scale and larger-scale deployment and to drive the research and development work needed to attain technical maturity. A description of the evaluation system is provided, and examples are given to illustrate how it is used to assist in component R&D decisions.

  8. Technical Assessment Team Report | Department of Energy

    Energy Savers [EERE]

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page onYou are now leaving Energy.gov You are now leaving Energy.gov You are being directedAnnual Siteof Energy 2, 2015 - January 16, 2015MeetingsElectric WaterTaxTechnical &Technical

  9. E-Print Network 3.0 - analysis technical evaluation Sample Search...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Technical 12... Technical Thomas Ballestero Dept. of Civil Engineering, CEPS DOI FWS Stream Restoration Design... for Southampton Creek, PA General* Technical* Amitava...

  10. E-Print Network 3.0 - analysis technical report-constructor Sample...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Technical 12... Technical Thomas Ballestero Dept. of Civil Engineering, CEPS DOI FWS Stream Restoration Design... for Southampton Creek, PA General* Technical* Amitava...

  11. DOE-TSPP-8-2013, Converting DOE Technical Standards to Voluntary...

    Energy Savers [EERE]

    8-2013, Converting DOE Technical Standards to Voluntary Consensus Standards DOE-TSPP-8-2013, Converting DOE Technical Standards to Voluntary Consensus Standards Technical Standards...

  12. RISK REDUCTION THROUGH USE OF EXTERNAL TECHNICAL REVIEWS, TECHNOLOGY READINESS ASSESSMENTS AND TECHNICAL RISK RATINGS - 9174

    SciTech Connect (OSTI)

    Cercy, M; Steven P Schneider, S; Kurt D Gerdes, K

    2008-12-12T23:59:59.000Z

    The U.S. Department of Energy's Office of Environmental Management (DOE-EM) was established to achieve the safe and compliant disposition of legacy wastes and facilities from defense nuclear applications. A large majority of these wastes and facilities are 'one-of-a-kind' and unique to DOE. Many of the programs to treat these wastes have been 'first-of-a-kind' and unprecedented in scope and complexity. This has meant that many of the technologies needed to successfully disposition these wastes were not yet developed or required significant re-engineering to be adapted for DOE-EM's needs. The DOE-EM program believes strongly in reducing the technical risk of its projects and has initiated several efforts to reduce those risks: (1) Technology Readiness Assessments to reduce the risks of deployment of new technologies; (2) External Technical Reviews as one of several steps to ensure the timely resolution of engineering and technology issues; and (3) Technical Risk Ratings as a means to monitor and communicate information about technical risks. This paper will present examples of how Technology Readiness Assessments, External Technical Reviews, and Technical Risk Ratings are being used by DOE-EM to reduce technical risks.

  13. RISK REDUCTION THROUGH USE OF EXTERNAL TECHNICAL REVIEWS, TECHNOLOGY READINESS ASSESSMENTS AND TECHNICAL RISK RATINGS - 9174

    SciTech Connect (OSTI)

    Cercy, M; Steven P Schneider, S; Kurt D Gerdes, K

    2009-01-15T23:59:59.000Z

    The U.S. Department of Energy's Office of Environmental Management (DOE-EM) was established to achieve the safe and compliant disposition of legacy wastes and facilities from defense nuclear applications. A large majority of these wastes and facilities are 'one-of-a-kind' and unique to DOE. Many of the programs to treat these wastes have been 'first-of-a-kind' and unprecedented in scope and complexity. This has meant that many of the technologies needed to successfully disposition these wastes were not yet developed or required significant re-engineering to be adapted for DOE-EM's needs. The DOE-EM program believes strongly in reducing the technical risk of its projects and has initiated several efforts to reduce those risks: (1) Technology Readiness Assessments to reduce the risks of deployment of new technologies; (2) External Technical Reviews as one of several steps to ensure the timely resolution of engineering and technology issues; and (3) Technical Risk Ratings as a means to monitor and communicate information about technical risks. This paper will present examples of how Technology Readiness Assessments, External Technical Reviews, and Technical Risk Ratings are being used by DOE-EM to reduce technical risks.

  14. Cell Data Sheet Specification (Presentation)

    SciTech Connect (OSTI)

    Kurtz, S.

    2012-03-01T23:59:59.000Z

    The presentation shows a brief status report on the development of a specification being considered by IEC TC82 WG7 for a concentrator cell data sheet and solicits suggestions from the community.

  15. Oak Ridge Site Specific Advisory ...

    Office of Environmental Management (EM)

    Ridge Site Specific Advisory Board * P.O. Box 2001, EM-91, Oak Ridge, TN 37831 Phone: 865-241-4583, 865-241-4584, 1-800-382-6938 * Fax: 865-574-3521 * Internet:...

  16. Building Energy Data Exchange Specification Scoping Report |...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Building Energy Data Exchange Specification Scoping Report Building Energy Data Exchange Specification Scoping Report The Building Energy Data Exchange Specification (BEDES),...

  17. PhD student in Energy Technology, specifically in Energy storage in the The School of Industrial Engineering and Management at the Royal Institute of

    E-Print Network [OSTI]

    Kazachkov, Ivan

    PhD student in Energy Technology, specifically in Energy storage in the ground The School Technology, specifically Energy storage in the ground. KTH is the largest technical university in Sweden the possibility to finance a Ph.D. student for studies of storage of energy, primarily as heat in borehole rock

  18. PhD student in Energy Technology, specifically in Magnetic Refrigeration The School of Industrial Engineering and Management at the Royal Institute of

    E-Print Network [OSTI]

    Kazachkov, Ivan

    PhD student in Energy Technology, specifically in Magnetic Refrigeration Processes The School Technology, specifically Magnetic Refrigeration Processes. KTH is the largest technical university in Sweden progress and it can be expected that magnetic refrigeration processes will be used also in consumer

  19. Technical Support Document for Version 3.4.0 of the COMcheck Software

    SciTech Connect (OSTI)

    Bartlett, Rosemarie; Connell, Linda M.; Gowri, Krishnan; Halverson, Mark A.; Lucas, Robert G.; Richman, Eric E.; Schultz, Robert W.; Winiarski, David W.

    2007-09-14T23:59:59.000Z

    COMcheck provides an optional way to demonstrate compliance with commercial and high-rise residential building energy codes. Commercial buildings include all use groups except single family and multifamily not over three stories in height. COMcheck was originally based on ANSI/ASHRAE/IES Standard 90.1-1989 (Standard 90.1-1989) requirements and is intended for use with various codes based on Standard 90.1, including the Codification of ASHRAE/IES Standard 90.1-1989 (90.1-1989 Code) (ASHRAE 1989a, 1993b) and ASHRAE/IESNA Standard 90.1-1999 (Standard 90.1-1999). This includes jurisdictions that have adopted the 90.1-1989 Code, Standard 90.1-1989, Standard 90.1-1999, or their own code based on one of these. We view Standard 90.1-1989 and the 90.1-1989 Code as having equivalent technical content and have used both as source documents in developing COMcheck. This technical support document (TSD) is designed to explain the technical basis for the COMcheck software as originally developed based on the ANSI/ASHRAE/IES Standard 90.1-1989 (Standard 90.1-1989). Documentation for other national model codes and standards and specific state energy codes supported in COMcheck has been added to this report as appendices. These appendices are intended to provide technical documentation for features specific to the supported codes and for any changes made for state-specific codes that differ from the standard features that support compliance with the national model codes and standards.

  20. Technical Support Document for Version 3.9.1 of the COMcheck Software

    SciTech Connect (OSTI)

    Bartlett, Rosemarie; Connell, Linda M.; Gowri, Krishnan; Halverson, Mark A.; Lucas, Robert G.; Richman, Eric E.; Schultz, Robert W.; Winiarski, David W.

    2012-09-01T23:59:59.000Z

    COMcheck provides an optional way to demonstrate compliance with commercial and high-rise residential building energy codes. Commercial buildings include all use groups except single family and multifamily not over three stories in height. COMcheck was originally based on ANSI/ASHRAE/IES Standard 90.1-1989 (Standard 90.1-1989) requirements and is intended for use with various codes based on Standard 90.1, including the Codification of ASHRAE/IES Standard 90.1-1989 (90.1-1989 Code) (ASHRAE 1989a, 1993b) and ASHRAE/IESNA Standard 90.1-1999 (Standard 90.1-1999). This includes jurisdictions that have adopted the 90.1-1989 Code, Standard 90.1-1989, Standard 90.1-1999, or their own code based on one of these. We view Standard 90.1-1989 and the 90.1-1989 Code as having equivalent technical content and have used both as source documents in developing COMcheck. This technical support document (TSD) is designed to explain the technical basis for the COMcheck software as originally developed based on the ANSI/ASHRAE/IES Standard 90.1-1989 (Standard 90.1-1989). Documentation for other national model codes and standards and specific state energy codes supported in COMcheck has been added to this report as appendices. These appendices are intended to provide technical documentation for features specific to the supported codes and for any changes made for state-specific codes that differ from the standard features that support compliance with the national model codes and standards. Beginning with COMcheck version 3.8.0, support for 90.1-1989, 90.1-1999, and the 1998 IECC and version 3.9.0 support for 2000 and 2001 IECC are no longer included, but those sections remain in this document for reference purposes.

  1. Technical Support Document for Version 3.9.0 of the COMcheck Software

    SciTech Connect (OSTI)

    Bartlett, Rosemarie; Connell, Linda M.; Gowri, Krishnan; Halverson, Mark A.; Lucas, R. G.; Richman, Eric E.; Schultz, Ralph W.; Winiarski, David W.

    2011-09-01T23:59:59.000Z

    COMcheck provides an optional way to demonstrate compliance with commercial and high-rise residential building energy codes. Commercial buildings include all use groups except single family and multifamily not over three stories in height. COMcheck was originally based on ANSI/ASHRAE/IES Standard 90.1-1989 (Standard 90.1-1989) requirements and is intended for use with various codes based on Standard 90.1, including the Codification of ASHRAE/IES Standard 90.1-1989 (90.1-1989 Code) (ASHRAE 1989a, 1993b) and ASHRAE/IESNA Standard 90.1-1999 (Standard 90.1-1999). This includes jurisdictions that have adopted the 90.1-1989 Code, Standard 90.1-1989, Standard 90.1-1999, or their own code based on one of these. We view Standard 90.1-1989 and the 90.1-1989 Code as having equivalent technical content and have used both as source documents in developing COMcheck. This technical support document (TSD) is designed to explain the technical basis for the COMcheck software as originally developed based on the ANSI/ASHRAE/IES Standard 90.1-1989 (Standard 90.1-1989). Documentation for other national model codes and standards and specific state energy codes supported in COMcheck has been added to this report as appendices. These appendices are intended to provide technical documentation for features specific to the supported codes and for any changes made for state-specific codes that differ from the standard features that support compliance with the national model codes and standards. Beginning with COMcheck version 3.8.0, support for 90.1-1989, 90.1-1999, and the 1998 IECC are no longer included, but those sections remain in this document for reference purposes.

  2. TESLA-LNF TECHNICAL NOTE Divisione Acceleratori

    E-Print Network [OSTI]

    TESLA-LNF TECHNICAL NOTE _____________ Divisione Acceleratori Frascati, November 20, 2003 Note: TESLA Report 2003-26 TESLA DAMPING RING: INJECTION/EXTRACTION SCHEMES WITH RF DEFLECTORS D. Alesini, S/extraction schemes in the Damping Ring of TESLA using RF deflectors. We illustrate different possible solutions using

  3. Technical University of Denmark rsted DTU Automation

    E-Print Network [OSTI]

    Technical University of Denmark �rsted · DTU Automation Project: SICAM - SIngle Conversion stage;Isolated PDM and PWM DC-AC SICAMs Petar Ljusev, MSc., Ph.D. student, �rsted · DTU Automation e-mail: pl

  4. Final Technical Report: Hawaii Hydrogen Center for

    E-Print Network [OSTI]

    Alkaline Electrolyzer System 8 2.4.1.2 5 kW PEM Fuel Cell System 9 2.4.2 Experiments/Results and Economic 2.8 Acknowledgements 47 2.9 References 47 3 Task 2 ­ Hydrogen Fuel Purity Assessment 49 3.1 GoalsFinal Technical Report: Hawaii Hydrogen Center for Development and Deployment of Distributed Energy

  5. Technical Note Puncture protection of PVC geomembranes______________________________________________

    E-Print Network [OSTI]

    Technical Note Puncture protection of PVC geomembranes a design procedure for estimating the puncture protection of polyvinyl chloride (PVC) geomembranes. The puncture resistance of 0.5 mm, 0.75 mm, and 1.0 mm thick PVC geomembranes was measured using the truncated

  6. Ocean Engineering 33 (2006) 22092223 Technical Note

    E-Print Network [OSTI]

    Mohseni, Kamran

    Ocean Engineering 33 (2006) 2209­2223 Technical Note Pulsatile vortex generators for low-speed maneuvering of small underwater vehicles Kamran Mohseni� Department of Aerospace Engineering Sciences, science writer). #12;1. Introduction Oceans hold the key to the origin and continuity of life on the Earth

  7. Technical Report Documentation Page 1. Report No.

    E-Print Network [OSTI]

    Texas at Austin, University of

    Office P.O. Box 5080 Austin, TX 78763-5080 13. Type of Report and Period Covered Technical Report with potentially significant cost implications. This research project is designed to address issues associated, floodplain, Weir equations, culvert, flow, test channel, return channel, Pitot tube 18. Distribution

  8. Water Research Institute Annual Technical Report

    E-Print Network [OSTI]

    Water Research Institute Annual Technical Report FY 2002 Introduction Research Program #12;MtBE in Groundwater: The Maine Experiment Basic Information Title: MtBE in Groundwater: The Maine Experiment Project, J.M. (2002) The occurrence and persistence of MtBE in groundwater in Windham, Maine, NE FOCUS Conf

  9. Water Resources Research Center Annual Technical Report

    E-Print Network [OSTI]

    Water Resources Research Center Annual Technical Report FY 1999 Introduction PROGRAM REPORT FLORIDA WATER RESOURCES RESEARCH CENTER FEDERAL GRANT NO. 1434-HQ-96-GRO2663 PERIOD: March 1, 1999 - February 29, 2000 The Water Resources Research Center (WRRC) was re-established as a separate entity from

  10. Water Resources Research Institute Annual Technical Report

    E-Print Network [OSTI]

    Water Resources Research Institute Annual Technical Report FY 2003 Introduction The Puerto Rico Water Resources and Environmental Research Institute (PRWRERI) is one of 54 water research centers objectives of the Puerto Rico Water Resources and Environmental Research Institute are (1) to conduct

  11. Nebraska Water Resources Center Annual Technical Report

    E-Print Network [OSTI]

    Nebraska Water Resources Center Annual Technical Report FY 2010 Nebraska Water Resources Center of the University of Nebraska Water Center as of September 2009. Lorrie Benson, J.D. serves as the assistant, respectively. The Water Center staff also includes Rachael Herpel as the water outreach specialist. Duane

  12. Nebraska Water Resources Center Annual Technical Report

    E-Print Network [OSTI]

    Nebraska Water Resources Center Annual Technical Report FY 2011 Nebraska Water Resources Center Engineering Department at the University of Nebraska-Lincoln, took over as the interim director of the Water Liedle serve as the communications specialist and program specialist, respectively. The Water Center

  13. Technical Note Graphene: Substrate preparation and introduction

    E-Print Network [OSTI]

    Technical Note Graphene: Substrate preparation and introduction Radosav S. Pantelic a , Ji Won Suk September 2010 Accepted 4 October 2010 Available online xxxx Keywords: Graphene Graphene oxide Cryo the transfer of continuous, single-layer, pristine graphene to standard Quan- tifoil TEM grids. We compare

  14. C. David (Dave) Warren Field Technical Manager

    E-Print Network [OSTI]

    , Processing Technologies 1B lbs/year Wind Energy Enables Longer Blade Designs and More EfficientC. David (Dave) Warren Field Technical Manager Transportation Materials Research Oak Ridge National by UT-Battelle for the U.S. Department of Energy Presentation_name Questions for Today Materials How can

  15. TECHNICAL REPORT: MODEL SENSITIVITY TO SURFACE TOPOGRAPHY

    E-Print Network [OSTI]

    Forget, François

    TECHNICAL REPORT: MODEL SENSITIVITY TO SURFACE TOPOGRAPHY ESTEC Contract 11369/95/NL/JG S. R. Lewis and Consortium Topography . . . . . . . . . . . . . 7 3 Studies of Sensitivity to Surface Topography 9 3.1 Zonal with respect to the surface topography with particular emphasis on any differences which may be important

  16. Technical Considerations for Broadband Powerline (BPL) Communication

    E-Print Network [OSTI]

    Technical Considerations for Broadband Powerline (BPL) Communication Robert G. Olsen1 1 School of the electric power transmission and distribution system as a transmission medium for broadband communications for the unlicensed systems that use the power system as a communications medium. I. INTRODUCTION The possible use

  17. ELKHORN SLOUGH TECHNICAL REPORT SERIES 2009: 1

    E-Print Network [OSTI]

    California at Santa Cruz, University of

    Research Reserve and the Elkhorn Slough Foundation Synthesis for Management of Eutrophication Issues in Elkhorn Slough Brent Hughes April 2009 (Updated March 2010) #12;Eutrophication in Elkhorn Slough 2 B of eutrophication issues in Elkhorn Slough. Elkhorn Slough Technical Report Series 2009:1. AUTHOR AFFLIATION

  18. Lasers and Optical Engineering Concentration Technical Electives

    E-Print Network [OSTI]

    Schumacher, Russ

    Lasers and Optical Engineering Concentration Technical Electives Course Number Course Title Credits495¹ Independent Study 1-3 n/a F,S,SS ECE503 Ultrafast Optics 3 ECE 342 S ECE504 Physical Optics 3 ECE 353 F ECE506 Optical Interferometry and Laser Metrology ECE 341; ECE 342; ECE 441 F ECE507 Plasma

  19. UNITED STATES NUCLEAR WASTE TECHNICAL REVIEW BOARD

    E-Print Network [OSTI]

    's mission, continuing role, and refocused goals as the U.S. approach to managing spent nuclear fuel and high an ongoing and integrated technical peer review of all DOE activities related to managing spent nuclear fuel, and the characteristics and quantities of waste associated with adopting alternatives for spent nuclear fuel management

  20. United States Nuclear Waste Technical Review Board

    E-Print Network [OSTI]

    Programs to Manage High-Level Radioactive Waste and Spent Nuclear Fuel in the United States and Other-Level Radioactive Waste and Spent Nuclear Fuel in the United States and Other Countries A Report to CongressUnited States Nuclear Waste Technical Review Board Experience Gained From Programs to Manage High